| Age | Commit message (Collapse) | Author |
|---|
|
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <[email protected]>
Signed-off-by: York Sun <[email protected]>
|
|
Signed-off-by:Jason Jin <[email protected]>
|
|
|
|
Patch by Martin Krause, 20 Mar 2006
Signed-off-by: Martin Krause <[email protected]>
|
|
Patch by Markus Klotzbuecher, 12 Jul 2006
|
|
|
|
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
|
|
|
|
Set Timer Clock Select to use CPU clock as a timer input source.
|
|
|
|
|
|
Enabled it for Yucca board.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <[email protected]>
|
|
* Added support for PCI2 on CDS
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <[email protected]>
|
|
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <[email protected]>
|
|
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <[email protected]>
|
|
Patch by Andy Fleming on 17-Mar-2006
Signed-off-by: Andy Fleming <[email protected]>
|
|
Patch by Jon Loeliger 17-Jan-2006
Signed-off-by: Jon Loeliger <[email protected]>
|
|
Patch by Matthew McClintock 26-June-2006
|
|
|
|
Signed-off-by: Jason Jin <[email protected]>
|
|
|
|
signed-off-by: Jason Jin <[email protected]>
signed-off-by: Wei Zhang <[email protected]>
|
|
Signed-off-by: Jason Jin <[email protected]>
|
|
|
|
|
|
|
|
|
|
Patch from Richard Danter, 12 Aug 2005
|
|
|
|
Patch by Thomas Lange, Aug 11 2005
|
|
Patch by Martin Krause, 8 Jun 2006
This patch supports two serial consoles on boards with
a MPC5xxx CPU. The console can be switched at runtime
by setting stdin, stdout and stderr to the desired serial
interface (serial0 or serial1). The PSCs to be used as
console port are definded by CONFIG_PSC_CONSOLE
and CONFIG_PSC_CONSOLE2.
See README.serial_multi for details.
|
|
Patch by Martin Krause, 17 Nov 2005
|
|
Patch by Martin Krause, 07 Nov 2005
Tested on a STK85XX baseboard. Make sure the PS/2 controller
has been programmed. Jumper Settings: X66 1-2, 9-10; X61 2-3
|
|
Make the automatic CS configuration the default.
The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
and CONFIG_TQM5200_AC are removed.
"TQM5200_config" is now the default for STK52XX.200 base boards.
On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
Patch by Martin Krause, 07 Nov 2005
|
|
Patch by Martin Krause, 27 Oct 2005
|
|
Patch by Martin Krause, 27 Oct 2005
|
|
|
|
|
|
- Add support for mpc8xx USB device.
- Add support for Common Device Class - Abstract Control Model USB console.
- Add support for flow control in USB slave devices.
- Add support for switching between gserial and cdc_acm using environment.
- Minor changes to usbdcore_omap1510.c usbdcore_omap1510.h
- Update usbcore slightly to ease host enumeration.
- Fix non-portable endian problems in usbdcore and usbdcore_ep0.
- Add AdderUSB_config as a defconfig to enable usage of the USB console
by default with the Adder87x U-Boot port.
Patches by Bryan O'Donoghue <[email protected]>, 29 May 2006
|
|
Patch by Stefan Roese, 13 Jun 2006
|
|
|
|
|
|
Patch by Scott McNutt, 08 Jun 2006
|
