| Age | Commit message (Collapse) | Author |
|---|
|
Pull request net-20251022
net:
- airoha: improvements
- Tighten a few more driver dependencies
- designware: fix bitbang init error
- phy: Make driver overloading get_phy_id depend on !COMPILE_TEST
- phy: add paged PHY register accessors
- make dhcp_run() common for NET and NET_LWIP
- dwc_eth_ops: Correct check for FDT_64BIT
- mediatek: mt7988: various fixup + MDIO detach
- phy: aquantia: switch to use phy_get_ofnode(), fix bindings typo
net-legacy:
- bootp: Prevent buffer overflow to avoid leaking the RAM content
- tftp: make TFTP ports unconditionally configurable
misc:
- uthreads: Make use of CONFIG_IS_ENABLED consistently
|
|
https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 features for the 2026.01 cycle:
This small fixes set includes a change on clocks register value and a
fix for the sam9x60ek default timer.
|
|
Synchronize paged PHY helpers with Linux v6.17.
Add support for PHY devices that use paged register access by
implementing the following functions:
- phy_save_page(): Save current page number
- phy_select_page(): Switch to a specific page and return previous page
- phy_restore_page(): Restore previously saved page
Also adds read_page and write_page callbacks to the phy_driver
structure to enable driver-specific page handling.
These helpers allow safe access to paged PHY registers by ensuring
proper page selection and restoration,
even in error conditions, which will be used by the Airoha PHY driver.
Signed-off-by: Lucien.Jheng <[email protected]>
|
|
There are currently two implementations of dhcp_run(): one in cmd/net.c
for NET and one in net/lwip/dhcp.c for NET_LWIP. There is no
justification for that. Therefore, move the NET version into
net/net-common.c to be used by both stacks, and drop the NET_LWIP
version which by the way does not look totally correct.
Signed-off-by: Jerome Forissier <[email protected]>
Suggested-by: Tom Rini <[email protected]>
Acked-by: Benjamin Hahn <[email protected]>
|
|
We do not yet support UTHREADS in xPL phases. However, we have the need
to dummy out certain functions so that xPL can build when full U-Boot
has UTHREADS enabled. Update the few places that need to use
CONFIG_IS_ENABLED so that we have the correct dummy in xPL.
Signed-off-by: Tom Rini <[email protected]>
Acked-by: Jerome Forissier <[email protected]>
|
|
Falcon mode loads a kernel file and an args file which is the
device-tree. However in the case of kernel file being a FIT that
contains the device-tree within it, loading the args file is not
required.
Therefore, this patch introduces a new SPL_OS_BOOT_ARGS config options
that allows us to enable or disable loading of the args file in falcon
mode.
Signed-off-by: Anshul Dalal <[email protected]>
|
|
Remove default values for PMC PLL Analog Control Register(ACR) as the
values are specific for each SoC and PLL, so load them from PLL
characteristics structure
Signed-off-by: Manikandan Muralidharan <[email protected]>
Signed-off-by: Varshini Rajendran <[email protected]>
|
|
This partly fix commit 726404a66c773 ("airoha: rework RAM size handling
to support multiple RAM size")
The function get_effective_memsize() do not see non-global defines
of CFG_MAX_MEM_MAPPED, so the effective memory size will not be changed.
Fix the issue by putting definition of CFG_MAX_MEM_MAPPED to the proper
place.
Fixes: 726404a66c773 ("airoha: rework RAM size handling to support multiple RAM size")
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
|
|
Add a few comments about global bootmeths and first_glob_method
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Mattijs Korpershoek <[email protected]>
Reviewed-by: Sam Protsenko <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
AMD/Xilinx/FPGA changes for v2026.01-rc1 v2
zynqmp:
- DT updates
- Enable new commands
mbv:
- Simplify defconfigs
clk:
- Separate legacy handler and use SMC handler
misc:
- Tighten TTC Kconfig dependency
net:
- Add 10GBE support to Gem
pwm:
- cadence-ttc: Fix array sizes
fwu:
- Add platform hook support
spi:
- Remove undocumented cdns,is-dma property
video:
- Fix DPSUB RGB handling
|
|
https://source.denx.de/u-boot/custodians/u-boot-tpm
TPM changes:
Make all drive names defined with U_BOOT_DRIVER unique
TEE changes:
Rework things such that sandbox will also traverse the optee directory
when SANDBOX_TEE is enabled, but only build one of the optee-specific
files when OPTEE is enabled.
EFI changes:
Up to now we were relying on the file extension to accept and load
an image over HTTP. We expected images to be either .iso or .img.
By wiring up internal existing functions we can try to mount any
file extension and reject it only if mounting fails.
part_driver_lookup_type
|
|
Make part_driver_lookup_type non-static so it can be used outside
part.c. This allows external callers to determine the appropriate
partition driver for a block device, enabling more flexible handling of
partition types.
Add a prototype and kernel-doc comment in part.h to document the
function contract. Provide a stub inline implementation returning NULL
when partition support is disabled, ensuring build consistency across
configurations.
Signed-off-by: Javier Tia <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Ilias Apalodimas <[email protected]>
|
|
Today, only a few platforms enable SPL_LOAD_FIT_FULL, and all enable
SPL_LOAD_FIT. As can be seen in usage, the FULL symbol is a superset of
the first symbol, not an alternative. Update Kconfig entries based on
this and simplify the only code which checks for either being set.
Signed-off-by: Tom Rini <[email protected]>
|
|
Matthias Schiffer <[email protected]> says:
Following a discussion on the LKML [1], there has been a clarification
of the correct use of the rgmii(/-rxid/-txid/-it) phy-modes [2] - namely,
that they don't describe the interface at the MAC or PHY boundary, but
whether the PCB traces add delays or not (where it is
implementation-defined whether the delays are added on the MAC or PHY
side in the latter case).
Accordingly, a fixup has been implemented in the am65-cpsw-nuss driver
to make it follow the clarified rules [3]; apply the same change to
U-Boot. Backwards compatibility is preserved: using an old DTB with
the wrong phy-mode only results in a warning message, but keeps the
Ethernet working. With a new DTB from Linux 6.17+ that sets the mode to
rgmii-id, these changes are necessary to avoid using an unsupported/
reserved configuration. See the commit message of patch 2/2 for some
additional detail.
[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c360eb0c3ccb95306704fd221442283ee82f1f58
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=ca13b249f291f4920466638d1adbfb3f9c8db6e9
Link: https://lore.kernel.org/r/[email protected]
|
|
dm_eth_phy_connect_interface() is a variant of dm_eth_phy_connect() that
allows to set the used PHY mode, in case the MAC driver needs to fix it
up. The previously static dm_eth_connect_phy_handle() is renamed and
extended for this purpose.
Signed-off-by: Matthias Schiffer <[email protected]>
|
|
While we declare some of our dummy functions as "inline" we do not also
declare them as "static" and so it is possible for the compiler to
decide to make these as global functions instead. This can lead to link
time failures in some cases, such as "allyesconfig". As these are just
dummy functions, convert them to a macro instead.
Signed-off-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-nand-flash
This series adds significant and valuable work by Mikhail Kshevetskiy to
align spi-mem with Linux 6.16. It also includes contributions to the mtd
performance patches, a work started by Miquel Raynal and improved by
Mikhail Kshevetskiy. Additionally, two patches tighten dependencies on
the Atmel driver.
The patches pass the pipeline CI:
https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/27873
|
|
Peng Fan (OSS) <[email protected]> says:
Misc update on firmware scmi:
- Typo fix
- Use io helpers
- Use PAGE_SIZE for arm64
- Add IN_USE error code
- Add more error info
- Support scmi max rx timeout in mailbox
- Add myself as scmi maintainer, AKASHI contributed most code, but
seems he is not invovled in the developement anymore, I volunteer to
help here.
Some items on list that I am thinking to add:
- align with linux kernel to use cpu_to_le32 and le32_to_cpu, but have not find
a good way to use the helpers.
- Add SCMI version negotiation as Linux Kernel
Link: https://lore.kernel.org/r/[email protected]
|
|
In SCMI spec 3.2, there is an update:
Add IN_USE error code for usage with Pin control protocol
So add the error decoding for IN_USE.
Signed-off-by: Peng Fan <[email protected]>
|
|
The script based firmware loader does not use anything from the
fs_loader implementation. Separate it into its own library source
file and convert the mediatek PHY to use this separate code. This
should reduce the amount of code that is pulled in alongside the
firmware loader, as the FS loader is no longer included.
Signed-off-by: Marek Vasut <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27872
- Several improvements for kontron-sl-mx8mm.
- Add rauc to bootmeths to phycore_imx8mp.
- Fix imx93_frdm USB vendor ID.
|
|
FWU metadata information is unavailable for platform-specific
operations since FWU initialization has not yet occurred.
The initialization function is invoked as part of the main
loop event. To address this, the FWU platform hook function
is introduced during FWU initialization, allowing metadata
processing with platform-specific operations.
Signed-off-by: Padmarao Begari <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Currently xilinx_pm_request API supports four u32 payloads. However the
legacy SMC format supports five u32 request payloads and extended SMC
format supports six u32 request payloads. Add support for the same in
xilinx_pm_request API. Also add two dummy arguments to all the callers
of xilinx_pm_request.
The TF-A always fills seven u32 return payload so add support
for the same in xilinx_pm_request API.
Signed-off-by: Naman Trivedi <[email protected]>
Signed-off-by: Venkatesh Yadav Abbarapu <[email protected]>
Acked-by: Senthil Nathan Thangaraj <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/5ae6b560741f3ca8b89059c4ebb87acf75b4718e.1756388537.git.michal.simek@amd.com
|
|
This define is obsolete, and bus width is now handled via
CONFIG_SYS_NAND_BUSWIDTH_16BIT option.
Signed-off-by: Yegor Yefremov <[email protected]>
|
|
Linux kernel .get_temp() callback reports values in millicelsius,
U-Boot currently reports them in celsius. Align the two and report
in millicelsius. Update drivers accordingly. Update callsites that
use thermal_get_temp() as well.
The 'temperature' command now reports temperature in millicelsius
as well, with additional accuracy. This changes command line ABI
slightly.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Quentin Schulz <[email protected]>
Reviewed-by: David Zang <[email protected]>
[trini: Update test/cmd/temperature.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use plain buffer pointer in request_firmware_into_buf_via_script()
instead of a pointer to pointer. The later is not necessary as the
request_firmware_into_buf_via_script() does not modify the buffer
pointer. Update the mediatek driver to match.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Weijie Gao <[email protected]>
|
|
The bootstd framework is the new way to support various bootflows
and media. Use it instead of legacy distro boot.
Signed-off-by: Frieder Schrempf <[email protected]>
|
|
This makes the U-Boot SPI NAND driver almost the same as in Linux
6.17-rc1. The only major differences are:
* support of ECC engines. The Linux driver supports different ECC
engines while U-Boot uses on-die ECC only.
* per operation maximum SPI bus frequency
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
There is already a manufacturer hook, which is manufacturer specific but
not chip specific. We no longer have access to the actual NAND identity
at this stage so let's add a per-chip configuration hook to align the
chip configuration (if any) with the core's setting.
This is a port of linux commit
da55809ebb45 ("mtd: spinand: Add a ->configure_chip() hook")
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Mikhail Kshevetskiy <[email protected]> # U-Boot port
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot.
The patch is based on linux commit
666c299be696 (mtd: spinand: Enhance the logic when picking a variant)
created by Miquel Raynal <[email protected]>
The code was a bit restricted in the functionality since not all
required functionality is supported in the u-boot.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
The code was ported from linux-6.15
based on a linux commit c06b1f753bea (mtd: spinand: add OTP support)
created by Martin Kurbanov <[email protected]>
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
When the host ECC fails to correct the data error of NAND device,
there's a special read for data recovery method which can be setup
by the host for the next read. There are several retry levels that
can be attempted until the lost data is recovered or definitely
assumed lost.
This is the port of linux commit
f2cb43c98010 (mtd: spinand: Add read retry support)
Signed-off-by: Cheng Ming Lin <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Mikhail Kshevetskiy <[email protected]> # U-Boot port
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
The code was ported from linux-6.12. The original continuous reading
support was implemented by Miquel Raynal <[email protected]>
in linux commit 631cfdd0520d (mtd: spi-nand: Add continuous read support).
Here is an original patch description:
--------------------------------------
A regular page read consist in:
- Asking one page of content from the NAND array to be loaded in the
chip's SRAM,
- Waiting for the operation to be done,
- Retrieving the data (I/O phase) from the chip's SRAM.
When reading several sequential pages, the above operation is repeated
over and over. There is however a way to optimize these accesses, by
enabling continuous reads. The feature requires the NAND chip to have a
second internal SRAM area plus a bit of additional internal logic to
trigger another internal transfer between the NAND array and the second
SRAM area while the I/O phase is ongoing. Once the first I/O phase is
done, the host can continue reading more data, continuously, as the chip
will automatically switch to the second SRAM content (which has already
been loaded) and in turns trigger the next load into the first SRAM area
again.
From an instruction perspective, the command op-codes are different, but
the same cycles are required. The only difference is that after a
continuous read (which is stopped by a CS deassert), the host must
observe a delay of tRST. However, because there is no guarantee in Linux
regarding the actual state of the CS pin after a transfer (in order to
speed-up the next transfer if targeting the same device), it was
necessary to manually end the continuous read with a configuration
register write operation.
Continuous reads have two main drawbacks:
* They only work on full pages (column address ignored)
* Only the main data area is pulled, out-of-band bytes are not
accessible. Said otherwise, the feature can only be useful with on-die
ECC engines.
Performance wise, measures have been performed on a Zynq platform using
Macronix SPI-NAND controller with a Macronix chip (based on the
flash_speed tool modified for testing sequential reads):
- 1-1-1 mode: performances improved from +3% (2-pages) up to +10% after
a dozen pages.
- 1-1-4 mode: performances improved from +15% (2-pages) up to +40% after
a dozen pages.
This series is based on a previous work from Macronix engineer Jaime
Liao.
--------------------------------------
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
This is a port of linux commit
6d9d6ab3a82a (mtd: spinand: Introduce a way to avoid raw access)
Signed-off-by: Takahiro Kuwano <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Signed-off-by: Mikhail Kshevetskiy <[email protected]> # U-Boot port
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Add two flags for inserting the Plane Select bit into the column
address during the write_to_cache and the read_from_cache operation.
Add the SPINAND_HAS_PROG_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the write_to_cache operation.
Add the SPINAND_HAS_READ_PLANE_SELECT_BIT flag for serial NAND flash
that require inserting the Plane Select bit into the column address
during the read_from_cache operation.
This is a port of linux commit
ca229bdbef29 (mtd: spinand: Add support for setting plane select bits)
Signed-off-by: Cheng Ming Lin <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Mikhail Kshevetskiy <[email protected]> # U-Boot port
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
This makes the U-Boot SPI NAND driver almost the same as in Linux 6.10.
The only major difference is support of ECC engines. The Linux driver
supports different ECC engines while U-Boot uses on-die ECC only.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
This aligns spinand_wait() with the linux kernel. Instead of calling into
spi_mem_poll_status() which is not implemented in U-Boot, we code the
polling logic and make sure that schedule() is called periodically.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Use an enum to differentiate the type of I/O (reading or writing a
page). Also update the request iterator.
This is a port of linux commit
701981cab016 ("mtd: nand: Add a NAND page I/O request type")
Signed-off-by: Miquel Raynal <[email protected]>
Reviewed-by: Boris Brezillon <[email protected]>
Link: https://lore.kernel.org/linux-mtd/[email protected]
Signed-off-by: Mikhail Kshevetskiy <[email protected]> # U-Boot port
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on a linux commit 981d1aa0697c ("mtd: spinand: Use the spi-mem dirmap API")
created by Boris Brezillon <[email protected]> with additional
fixes taken from Linux 6.10.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
This pulls in multiple changes from the Linux kernel in order to keep
the code in sync. This also fixes octal mode support.
Signed-off-by: Mikhail Kshevetskiy <[email protected]>
Reviewed-by: Frieder Schrempf <[email protected]>
Signed-off-by: Michael Trimarchi <[email protected]>
|
|
While we continue to have some systems which support extremely legacy
OS booting methods, we do not have use cases for supporting this in
Falcon mode anymore. Remove this support and references from the
documentation.
Co-developed-by: Anshul Dalal <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Synchronize upper_NN_bits() and lower_NN_bits() macros with Linux 6.16
commit 118d777c4cb4 ("wordpart.h: Add REPEAT_BYTE_U32()"). This fixes the
lower_32_bits() macros and assures it works with 64bit systems correctly.
This also adds 16bit variants of these macros, which will be used by the
Airoha PHY driver.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-socfpga into next
SoCFPGA updates for v2025.10:
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27762
This pull request brings a set of updates across SoCFPGA platforms
covering Agilex5, Agilex7, N5X, and Stratix10. The changes include:
* Agilex5 enhancements:
- USB3.1 enablement and DWC3 host driver support
- System Manager register configuration for USB3
- Watchdog timeout increase and SDMMC clock API integration
- dcache handling improvements in SMC mailbox path
- Enable SPL_SYS_DCACHE_OFF in defconfig
* Clock driver improvements:
- Introduce dt-bindings header for Agilex clocks
- Add enable/disable API and EMAC clock selection fixes
- Replace manual shifts with FIELD_GET usage
* DDR updates:
- IOSSM mailbox compatibility check
- Correct DDR calibration status handling
* Device tree changes:
- Agilex5: disable cache allocation for reads
- Stratix10: add NAND IP node
- Enable driver model watchdog
- Enable USB3.1 node for Agilex5
* Config cleanups:
- Simplify Agilex7 VAB defconfig
- Remove obsolete SYS_BOOTM_LEN from N5X VAB config
- Enable CRC32 support for SoCFPGA
- Increase USB hub debounce timeout
Overall this set improves reliability of DDR and cache flows,
adds missing USB and MMC features for Agilex5, and refines clock
and configuration handling across platforms.
This patch set has been tested on Agilex 5 devkit, and Agilex devkit.
|
|
Introduce header file to define the clock indexes for the Agilex
platform.
Signed-off-by: Alif Zakuan Yuslaimi <[email protected]>
Reviewed-by: Tien Fong Chee <[email protected]>
|
|
Rasmus Villemoes <[email protected]> says:
This all started from me wondering "why does this standalone app end
up being so huge"? Oh, it essentially links in its own standard C
library to get strlen() and snprintf(). Which then led to asking "why
don't we export all those standard C functions when we have them
anyway?".
CI has chewed on these and seem happy - it was CI which told me about
the necessity of [1/9]: https://github.com/u-boot/u-boot/pull/813
Link: https://lore.kernel.org/r/[email protected]
|
|
There have been quite a few changes to _exports.h since the last
update of XF_VERSION, also before the previous patches in this series.
I doubt the mechanism is actually being used in practice, it is simply
too fragile: Not only does the list of exported functions depend on
.config, so with the same XF_VERSION the jump table entries could have
different offsets. But getting to the jump table itself from gd to
even call the ->get_version() is fragile, since offsetof(gd_t, jt)
can, and does, change. For example, as recently as commit
d9902107027 ("global_data: Remove jump table in SPL").
One really must build one's standalone app against the proper U-Boot
version and config.h. But for good measure, do bump it now.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The current list of exported functions lacks quite a few bog-standard C
library functions that we might as well expose, since U-Boot certainly
has them implemented anyway. There's no reason a standalone
application should have its own strlen() implementation or link in a
copy from some tiny libc.
For a customer's standalone app, this means it goes from 95K to 10K.
More importantly, we can ditch the custom toolchain including a
newlibc used to build the standalone app and just use the same
toolchain as used to build u-boot itself.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The current list of exported functions is somewhat of a
mess. Reorganize them so that related functionality is kept together:
- console I/O: move vprintf next to printf and the getc/putc functions
- integer parsing: move the *strto* functions together
- standard string.h stuff: move memset() and strcpy() next to strcmp()
- time: move mdelay() next to udelay() and get_timer()
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
After finishing a later patch in this series, I discovered I had
neglected to update the list of declarations in exports.h to
match. But then I realized I wasn't the first to do that.
Use the existing mechanism and DRY it out.
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Rasmus Villemoes <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
