| Age | Commit message (Collapse) | Author |
|---|
|
If no CONFIG_OPTEE_LOAD_ADDR is provided i.e. you are not loading OPTEE
into memory in u-boot, then just set the non-existent CONFIG option to
zero, elsewise stringify(CONFIG_OPTEE_LOAD_ADDR) will return
"CONFIG_OPTEE_LOAD_ADDR" - which looks weird in the u-boot environment.
Signed-off-by: Bryan O'Donoghue <[email protected]>
|
|
In the Mbed Linux OS bootflow OP-TEE runs before u-boot and provides a DTB
overlay at 0x83100000.
This overlay should subsequently be merged into the main DTB before handing
over to the kernel.
This patch defines fdtovaddr at 0x83100000.
Signed-off-by: Bryan O'Donoghue <[email protected]>
|
|
Reusing the loadaddr to load the boot script breaks some of the logic we
want to have around the bootscript/FIT load addresses. Making a dedicated
bootscript address allows us to differentiate the bootscript load address
from the Linux Kernel or OPTEE load address, thus ensuring that no matter
what the load sequence the bootscript and Kernel/OPTEE binary load
addresses do not conflict.
Signed-off-by: Bryan O'Donoghue <[email protected]>
|
|
When obtaining the bootscript from a FIT image we need to specify the name
of the bootscript as defined inside of the FIT.
This patch makes a define that appends a "bootscr" parameter to the source
command when compiling up in FIT mode on warp7.
An environment variable is supplied to enable others to use a different
name than "bootscr" as the image name of the boot script in their FIT.
Signed-off-by: Bryan O'Donoghue <[email protected]>
|
|
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Signed-off-by: Sergey Kubushyn <[email protected]>
Signed-off-by: Shyam Saini <[email protected]>
|
|
This patch provides code to implement the CCF clock tree in sandbox. It
uses all the introduced primitives; some generic ones are reused, some
sandbox specific were developed.
In that way (after introducing the real CCF tree in sandbox) the recently
added to clk-uclass.c: clk_get_by_id() and clk_get_parent_rate() are tested
in their natural work environment.
Usage (sandbox_defconfig and sandbox_flattree_defconfig):
./u-boot --fdt arch/sandbox/dts/test.dtb --command "ut dm clk_ccf"
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
The generic mux clock code for CCF requires reading the clock multiplexer
value from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the mux structure (accessible only when sandbox is run)
has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
The generic divider clock code for CCF requires reading the divider value
from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the divider structure (accessible only when sandbox is
run) has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This patch brings the files from Linux kernel (linux-stable/linux-5.1.y
SHA1: 5752b50477da)to provide clocks support as it is used on the Linux
kernel with Common Clock Framework [CCF] setup.
The directory structure has been preserved. The ported code only supports
reading information from PLL, MUX, Divider, etc and enabling/disabling
the clocks USDHCx/ECSPIx depending on used bus. Moreover, it is agnostic
to the alias numbering as the information about the clock is read from the
device tree.
One needs to pay attention to the comments indicating necessary for U-Boot's
driver model changes.
If needed, the code can be extended to support the "set" part of the clock
management.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit adds the clk_get_by_id() function, which is responsible
for getting the udevice with matching clk->id. Such approach allows
re-usage of inherit DM list relationship for the same class (UCLASS_CLK).
As a result - we don't need any other external list - it is just enough
to look for UCLASS_CLK related udevices.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This commit adds the clk_get_parent_rate() function, which is responsible
for getting the rate of parent clock.
Unfortunately, u-boot's DM support for getting parent is different
(the parent relationship is in udevice) than the one in Common Clock
Framework [CCF] in Linux.
To alleviate this problem - the clk_get_parent_rate() function has been
introduced to clk-uclass.c.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This commit adds the clk_get_parent() function, which is responsible
for getting the parent's struct clock pointer.
U-Boot's DM support for getting parent is different (the parent
relationship is in udevice) than the one in Common Clock Framework [CCF]
in Linux. To obtain the pointer to struct clk of parent the
pdev->uclass_priv field is read via dev_get_clk_ptr() wrapper.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This file now stores the dev_get_clk_ptr() wrapper on the dev_get_uclass_priv()
function.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This commit extends the struct clk to provide information regarding the
flags related to this devices.
Those flags are clk device agnostic and indicate generic features
(like e.g. CLK_GET_RATE_NOCACHE - the need to always recalculate the rate).
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This commit extends the struct clk to provide information regarding the
clock rate.
As a result the clock tree traversal is performed at most once, and further
reads are using the cached value.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
There is no UCLASS_CLOCK uclass defined. Instead we do use the UCLASS_CLK.
Signed-off-by: Lukasz Majewski <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
|
|
%s/ot/to/
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <[email protected]>
Tested-by: Heinrich Schuchardt <[email protected]>
|
|
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <[email protected]>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <[email protected]>
Reviewed-by: Simon Goldschmidt <[email protected]>
|
|
The block count entry in the EXT4 filesystem disk structures uses
standard 512-bytes units for most of the typical files. The only
exception are HUGE files, which use the filesystem block size, but those
are not supported by uboot's EXT4 implementation anyway. This patch fixes
the EXT4 code to use proper unit count for inode block count. This fixes
errors reported by fsck.ext4 on disks with non-standard (i.e. 4KiB, in
case of new flash drives) PHYSICAL block size after using 'ext4write'
uboot's command.
Signed-off-by: Marek Szyprowski <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
This will allow for downloading and applying overlays from an MMC/SD
boot media based on the overlay_files ENV variable containing a list
of overlay files.
Signed-off-by: Andreas Dannenberg <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
|
|
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
|
|
Add configs to support RAW boot mode in eMMC.
Signed-off-by: Faiz Abbas <[email protected]>
Signed-off-by: Andreas Dannenberg <[email protected]>
|
|
Switch to using the full malloc scheme in post-relocation SPL to allow
better utilization of available memory for example by allowing memory
to get freed. Initially allocate a 16MB-sized region in DDR starting
at address 0x84000000 for this purpose.
Signed-off-by: Andreas Dannenberg <[email protected]>
|
|
In order to be able to use more advanced driver functionality which often
relies on having BSS initialized during early boot prior to relocation
several things need to be in place:
1) Memory needs to be available for BSS to use. For this, we locate BSS
at the top of the MCU SRAM area, with the stack starting right below
it,
2) We need to move the initialization of BSS prior to entering
board_init_f(). We will do this with a separate commit by turning on
the respective CONFIG option.
In this commit we also clean up the assignment of the initial SP address
as part of the refactoring, taking into account the pre-decrement post-
increment nature in which the SP is used on ARM.
Signed-off-by: Andreas Dannenberg <[email protected]>
|
|
The current U-Boot SPL image loader infrastructure is very powerful,
able to initialize and load from a variety of boot media however it
is strongly geared towards loading specific types of images in a very
specific way. To address the need being able to use this infrastructure
to load arbitrary image files go ahead and refactor it as follows:
- Refactor existing spl_mmc_load_image function into superset function,
accepting additional arguments such as filenames and media load offset
(same concept can also be applied toother spl_XXX_load_image functions)
- Extend the loader function to "remember" their peripheral initialization
status so that the init is only done once during the boot process,
- Extend the FIT image loading function to allow skipping the parsing/
processing of the FIT contents (so that this can be done separately
in a more customized fashion)
- Populate the SPL_LOAD_IMAGE_METHOD() list with a trampoline function,
invoking the newly refactored superset functions in a way to maintain
compatibility with the existing behavior
This refactoring initially covers MMC/SD card loading (RAW and FS-based).
Signed-off-by: Andreas Dannenberg <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Add Support for creating a GPT partition for the filesystem in eMMC.
The filesystem is created in the user partition (partition 0).
Signed-off-by: Faiz Abbas <[email protected]>
|
|
Add configs such that U-boot environment is in eMMC by default.
Signed-off-by: Faiz Abbas <[email protected]>
|
|
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.
Also create a common API to set UHS timings in HOST_CONTROL2.
Signed-off-by: Faiz Abbas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Make set_ios_post() return int to faciliate error handling in
platform drivers.
Signed-off-by: Faiz Abbas <[email protected]>
|
|
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.
Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.
Signed-off-by: Faiz Abbas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
In device nodes with more than one entry in the reg property,
it is sometimes useful to regmap only of the entries. Add an
API regmap_init_mem_index() to facilitate this.
Signed-off-by: Faiz Abbas <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
- Beelink-x2 STB support (Marcus)
- H6 DDR3, LPDDR3 changes (Andre, Jernej)
- H6 pin controller, USB PHY (Andre)
|
|
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <[email protected]>
Tested-by: Corentin Labbe <[email protected]> # Pine-H64
Reviewed-by: Jagan Teki <[email protected]>
|
|
|
|
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
|
|
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <[email protected]>
|
|
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <[email protected]>
Signed-off-by: Anup Patel <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
sequence"
This reverts commit 318a7a576bc49aa8b4207e694d3fbd48c663d6ac.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <[email protected]>
|
|
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Removed MMC_CAP_NONREMOVABLE, MMC_CAP_NEEDS_POLL macros from
mvebu_mmc.h to avoid redefining of these macros when compiled with
mvebu based configs.
Signed-off-by: T Karthik Reddy <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- syscon: add support for power off
- stm32mp1: add op-tee config
- stm32mp1: add specific commands: stboard and stm32key
- add stm32 mailbox driver
- solve many stm32 warnings when building with W=1
- update stm32 gpio driver
|
|
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <[email protected]>
Tested-by: Michal Simek <[email protected]> (zcu102)
Tested-by: Patrick Delaunay <[email protected]>
|
|
Support for Phytech phyCORE AM335x R2 SOM (PCL060) on the Phytec
phyBOARD-Wega AM335x.
CPU : AM335X-GP rev 2.1
Model: Phytec AM335x phyBOARD-WEGA
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
eth0: ethernet@4a100000
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART
- USB (host)
Device trees were taken from Linux mainline:
commit 37624b58542f ("Linux 5.1-rc7")
Signed-off-by: Niel Fourie <[email protected]>
Signed-off-by: Parthiban Nallathambi <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Tested-by: Marek Vasut <[email protected]>
|
