summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2008-05-30[MIPS] <asm/mipsregs.h>: CodinygStyle cleanupsShinya Kuribayashi
No functional changes. Signed-off-by: Shinya Kuribayashi <[email protected]>
2008-05-28Make onenand_uboot.h self-sufficient.Scott Wood
Don't assume types are provided by previously included headers. Signed-off-by: Scott Wood <[email protected]>
2008-05-28NAND: Provide a sane default for NAND_MAX_CHIPS.Scott Wood
This allows the header to be included regardless of whether a board's config file provides NAND-related defininitions. Signed-off-by: Scott Wood <[email protected]>
2008-05-27avr32: Rework SDRAM initialization codeHaavard Skinnemoen
This cleans up the SDRAM initialization and related code a bit, and allows faster booting. * Add definitions for EBI and internal SRAM to asm/arch/memory-map.h * Remove memory test from sdram_init() and make caller responsible for verifying the SDRAM and determining its size. * Remove base_address member from struct sdram_config (was sdram_info) * Add data_bits member to struct sdram_config and kill CFG_SDRAM_16BIT * Add support for a common STK1000 hack: 16MB SDRAM instead of 8. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: Rename pm_init() as clk_init() and make SoC-specificHaavard Skinnemoen
pm_init() was always more about clock initialization than anything else. Dealing with PLLs, clock gating and such is also inherently SoC-specific, so move it into a SoC-specific directory. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: Clean up the HMATRIX codeHaavard Skinnemoen
Rework the HMATRIX configuration interface so that it becomes easier to configure the HMATRIX for boards with special needs, and add new parts. The HMATRIX header file has been split into a general, chip-independent part with register definitions, etc. and a chip-specific part with SFR bitfield definitions and master/slave identifiers. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: Add support for the ATSTK1006 boardHaavard Skinnemoen
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on board. It's currently in production and will be available soon. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: Get rid of the .flashprog sectionHaavard Skinnemoen
The .flashprog section was only needed back when we were running directly from flash, and it's even more useless on NGW100 since it uses the CFI flash driver which never used this workaround in the first place. Remove it on STK1000 as well, and get rid of all the associated code and annotations. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: Use correct condition around macb clock accessorsHaavard Skinnemoen
get_macb_pclk_rate() and get_macb_hclk_rate() should be available when the chip has a MACB controller, not when it has a USART. Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27avr32: stk1002 and ngw100 convergenceDavid Brownell
Make STK1002 and NGW100 boards act more alike: - STK boards can use as many arguments as NGW - STK boards don't need to manage FPGAs either - NGW commands should match STK ones Also spell U-Boot right in prompts for STK1002 and NGW100. Signed-off-by: David Brownell <[email protected]> [[email protected]: update STK100[34] as well] Signed-off-by: Haavard Skinnemoen <[email protected]>
2008-05-27Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
Conflicts: include/configs/socrates.h Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-27Socrates: Added USB support.Sergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]>
2008-05-27Socrates: add support for DS75 Digital Thermo Sensor on I2C bus.Sergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]>
2008-05-27Socrates: Config file cleanup.Sergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]>
2008-05-24Merging Stelian Pop AT91 patchesJean-Christophe PLAGNIOL-VILLARD
Merge branch 'testing-V2' Conflicts: board/atmel/at91cap9adk/Makefile Fixing copyright board/atmel/at91sam9260ek/Makefile Fixing copyright board/atmel/at91sam9260ek/u-boot.lds Delete no more needed ld script Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-22USB: add support for multiple PCI OHCI controllersSergei Poselenov
Add new configuration variable CONFIG_PCI_OHCI_DEVNO. In case of several PCI USB controllers on a board this variable specifys which controller to use. Also add USB support for sokrates board. See doc/README.generic_usb_ohci for details. Signed-off-by: Sergei Poselenov <[email protected]> Signed-off-by: Markus Klotzbuecher <[email protected]>
2008-05-21Merge branch 'quad100hd'Stefan Roese
2008-05-21Merge branch 'socrates' of /home/wd/git/u-boot/projectsWolfgang Denk
2008-05-21Merge branch 'lwmon5' of /home/wd/git/u-boot/projectsWolfgang Denk
2008-05-21Adding DIU support for Freescale 5121ADSYork Sun
Add DIU and cfb console support to FSL 5121ADS board. Use #define CONFIG_VIDEO in config file to enable fb console. Signed-off-by: York Sun <[email protected]>
2008-05-21Big white-space cleanup.Wolfgang Denk
This commit gets rid of a huge amount of silly white-space issues. Especially, all sequences of SPACEs followed by TAB characters get removed (unless they appear in print statements). Also remove all embedded "vim:" and "vi:" statements which hide indentation problems. Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-20socrates: fix second TSEC configuration (it is actually TSEC3)Sergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]>
2008-05-20socrates: changes to support FDTSergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]> Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-20Initial support for "Socrates" boardSergei Poselenov
Signed-off-by: Sergei Poselenov <[email protected]>
2008-05-20POST: replace the LOGBUFF_INITIALIZED flag in gd->post_log_word (1 << 31) ↵Yuri Tikhonov
with the GD_FLG_LOGINIT flag in gd->flags. This way we become able to utilize the full post_log_word for POST activities (overwise, POST ECC, which has 0x8000 ID, could be erroneously treated as started in post_output_backlog() even if there was actually no POST ECC run (because of OCM POST failure, for example). Signed-off-by: Yuri Tikhonov <[email protected]>
2008-05-20POST: add POST_STOP flagYuri Tikhonov
Don't run futher tests in case of a test fails that is marked as POST_STOP. Signed-off-by: Ilya Yanok <[email protected]> Signed-off-by: Yuri Tikhonov <[email protected]>
2008-05-20POST: switch CFG_POST_OCM with CFG_POST_CODEC (workaround)Yuri Tikhonov
Switch the OCM testid with the codec one. The reason is that current implementation requires the POST_ROM testid to fit into lower 16 bits, and the codec test will never run with POST_ROM hopefully. Signed-off-by: Ilya Yanok <[email protected]>
2008-05-20lwmon5: enable OCM post test on lwmon5 boardYuri Tikhonov
Signed-off-by: Ilya Yanok <[email protected]>
2008-05-20POST: OCM test added.Yuri Tikhonov
Added OCM test to POST layer. This version runs before all other tests but doesn't yet interrupt post sequence on failure. Signed-off-by: Ilya Yanok <[email protected]> Signed-off-by: Yuri Tikhonov <[email protected]>
2008-05-19Fix 8313ERDB board configurationYork Sun
Change LCRR clock ratio from 2 to 4 to commodate VSC7385. Correct TSEC1 vs TSEC2 assignment. Define ETHADDR and ETH1ADDR always. Signed-off-by: York Sun <[email protected]> Signed-off-by: Timur Tabi <[email protected]>
2008-05-19mpc86xx: Removed unused and unconfigured memory test code.Jon Loeliger
Besides, other common code exists. Signed-off-by: Jon Loeliger <[email protected]>
2008-05-14environment: fix bug introduced by commit a8409f4f1ac8Wolfgang Denk
env_get_char is not a function, but a pointer to one. Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-14Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xxWolfgang Denk
2008-05-14ppc4xx: QUAD100HD: Allow the environment to be put into flash.Gary Jennejohn
After moving TEXT_BASE the value for CFG_ENV_ADDR was incorrect. Also use a redundant environment. Signed-off-by: Gary Jennejohn <[email protected]>
2008-05-14environment: cleanup prototype declarations of env functions.Wolfgang Denk
Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-13Makefile: fix "error: version_autogenerated.h: No such file or directory"Wolfgang Denk
Signed-off-by: Wolfgang Denk <[email protected]>
2008-05-13ppc4xx: Add 405EX(r) revision C PVR definitions and detection codeStefan Roese
Signed-off-by: Stefan Roese <[email protected]>
2008-05-12Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2008-05-12Revert "Avoid initrd and logbuffer area overlaps"Wolfgang Denk
This reverts commit 1b5605ca57fbb364f4d78eeee28b974ed875e888 which breaks building on all PPC boards that don't use a log buffer.
2008-05-12Revert "Change env_get_char from a global function ptr to a function."Wolfgang Denk
This reverts commit c0559be371b2a64b1a817088c3308688e2182f93 which is known to break booting from dataflash and NAND.
2008-05-10AT91: Cleanup unused config header file definitions.Stelian Pop
CONFIG_ENV_OVERWRITE is commented out in the config header files, so let's cleanup the files by removing the whole definition. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10Support AT91CAP9 revC CPUsStelian Pop
The AT91CAP9 revC CPU has a few differences over the previous, revB CPU which was distributed in small quantities only (revA was an internal Atmel product only). The revC silicon needs a special initialisation sequence to switch from the internal (imprecise) RC oscillator to the external 32k clock. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9RLEK: hook up the ATMEL LCD driverStelian Pop
This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91SAM9RLEK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9263EK: hook up the ATMEL LCD driverStelian Pop
This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91SAM9263EK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9261EK: hook up the ATMEL LCD driverStelian Pop
This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91SAM9261EK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91CAP9ADK: hook up the ATMEL LCD driverStelian Pop
This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91CAP9ADK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10Add ATMEL LCD driverStelian Pop
This patch adds support for the ATMEL LCDC driver which is used on some AT91 and AVR platforms. Is has been tested with the AT91CAP9ADK, AT91SAM9261EK, AT91SAM9263EK and AT91SAM9RLEK boards. Adaptation for AVR32 should probably be easy. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9RLEK supportStelian Pop
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9263EK supportStelian Pop
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2008-05-10AT91SAM9261EK supportStelian Pop
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK board. Signed-off-by: Stelian Pop <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>