| Age | Commit message (Collapse) | Author |
|---|
|
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Aleksandar Gerasimovski <[email protected]>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <[email protected]>
Acked-by: Michael Walle <[email protected]> [for kontron-sl28]
Reviewed-by: Priyanka Jain <[email protected]>
|
|
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <[email protected]>
Signed-off-by: Mian Yousaf Kaukab <[email protected]>
Reviewed-by: Ramon Fried <[email protected]>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <[email protected]>
|
|
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Make it possible to invoke rescue boot from U-Boot console, without
having to press the factory reset button. This is needed when accessing
the device remotely, for example.
Achieve this by putting rescue command into `bootcmd_rescue` default
environment variable and setting some distroboot environment variables
to their default values when the factory button is pressed.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Add defconfig and board support for HiFive Unmatched.
Signed-off-by: Green Wan <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
Add dts support for fu740. The HiFive Unmatched support is based on
fu740 cpu and drivers in following patch set.
Signed-off-by: Green Wan <[email protected]>
[greentime.hu: set fu740 speed to 1.2GHz]
Signed-off-by: Greentime Hu <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Rick Chen <[email protected]>
|
|
"TCG PC Client Platform Firmware Profile Specification"
requires to measure every attempt to load and execute
a OS Loader(a UEFI application) into PCR[4].
This commit adds the PE/COFF image measurement, extends PCR,
and appends measurement into Event Log.
Acked-by: Ilias Apalodimas <[email protected]>
Tested-by: Ilias Apalodimas <[email protected]>
Signed-off-by: Masahisa Kojima <[email protected]>
Replace CONFIG_HASH_CALCULATE by CONFIG_HASH
Fix conversions between pointers and u64.
Signed-off-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Ilias Apalodimas <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Fix reset for AM64 platforms
- Enable networking PHY driver for AM64
- Fix default R5F cluster setting in J7
|
|
MLO has increased to a size greater than the allocated
128 kB in dfu_alt_info_emmc and _mmc.
Therefore, double the allocated size for MLO.raw in
the default environment.
Signed-off-by: Faiz Abbas <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
ut_asserteq_strn is defined twice. Remove one definition.
Fixes: 33d7edfd5f ("test: Add a way to check part of a console line or skip it")
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Remove qemu_mips boards because DM migration doesn't make sense.
The board support for qemu_mips is already marked as deprecated
in Qemu in favour of the Malta board. Also qemu_mips support
has been removed from Linux a long time ago.
The official replacement is the Malta board. The same Malta U-Boot
image can be used with Qemu and on physical hardware.
All combinations of Big Endian and Little Endian as well as 32 bit
and 64 bit are supported.
Signed-off-by: Daniel Schwierzeck <[email protected]>
|
|
When building with LTO, the system libc's `errno` variable used in
arch/sandbox/cpu/os.c conflicts with U-Boot's `errno` (defined in
lib/errno.c) with the following error:
.../ld: errno@@GLIBC_PRIVATE: TLS definition in /lib64/libc.so.6
section .tbss mismatches non-TLS reference in
/tmp/u-boot.EQlEXz.ltrans0.ltrans.o
To avoid this conflict use different asm label for this variable when
CONFIG_SANDBOX is enabled.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add macro __efi_runtime_rodata, for const variables with similar purpose
as those using __efi_runtime_data.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
Document the macros __efi_runtime and __efi_runtime_data in Sphinx
style.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Heinrich Schuchardt <[email protected]>
|
|
When linking with LTO, the compiler complains about type mismatch of
variables `__efi_runtime_start`, `__efi_runtime_stop`,
`__efi_runtime_rel_start` and `__efi_runtime_rel_stop`:
include/efi_loader.h:218:21: warning: type of ‘__efi_runtime_start’
does not match original
declaration [-Wlto-type-mismatch]
218 | extern unsigned int __efi_runtime_start, __efi_runtime_stop;
| ^
arch/sandbox/lib/sections.c:7:6: note: ‘__efi_runtime_start’ was
previously declared here
7 | char __efi_runtime_start[0] __attribute__((section(".__efi_run
| ^
Change the type to char[] in include/efi_loader.h.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Use UNIQUE_ID in the __ADDRESSABLE macro.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Signed-off-by: Stefan Chulski <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <[email protected]>
|
|
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <[email protected]>
|
|
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <[email protected]>
Reviewed-by: Maxime Ripard <[email protected]>
|
|
This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.
In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.
Based on this:
- "extension scan" makes the generic code call the board-specific
extension_board_scan() function to retrieve the list of detected
extension boards.
- "extension list" allows to list the detected extension boards.
- "extension apply <number>|all" allows to apply the Device Tree
overlay(s) corresponding to one, or all, extension boards
The latter requires two environment variables to exist and set one variable
to run:
- extension_overlay_addr: the RAM address where to load the Device
Tree overlays
- extension_overlay_cmd: the U-Boot command to load one overlay.
Indeed, the location and mechanism to load DT overlays is very setup
specific.
- extension_overlay_name: set by the command: the name of the DT which
will be load during the execution.
When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:
extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name
Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)
Signed-off-by: Kory Maincent <[email protected]>
Reviewed-by: Maxime Ripard <[email protected]>
|
|
Move the fdt_valid function to fdt_support.
This changes allow to be able to test the validity of a devicetree in
other c files.
Update code syntax.
Signed-off-by: Kory Maincent <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Maxime Ripard <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-ti
- Initial support for AM64 EVM and SK
- K3 DDR driver unification for J7 and AM64 platforms.
- Minor fixes for TI clock driver
|
|
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Grygorii Strashko <[email protected]>
|
|
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <[email protected]>
|
|
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Avoid R5 SPL stack writing into ROM index table. Re-use the same space
for storing EEPROM data.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Add pinctrl macros for AM64 SoC. These macro definitions are similar to
that of previous platforms, but adding new definitions to avoid any
naming confusions in the soc dts files.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
Add board specific initialization for am64x based boards.
Signed-off-by: Dave Gerlach <[email protected]>
|
|
This reverts commit d64b9cdcd475eb7f07b49741ded87e24dae4a5fc.
As pointed by [1] and [2], the reverted patch made every DT 'reg'
property translatable. What the patch was trying to fix was fixed in a
different way from previously submitted patches which instead of
correcting the generic address translation function fixed the issue with
appropriate platform code.
[1] https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
[2] https://lore.kernel.org/linux-clk/[email protected]/T/
Signed-off-by: Dario Binacchi <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20210502
-------------------
- mx6: fixes for Ventana
- local fixes from maintainer
- imx7d: Ronetix's iMX7-CM
- imx8: Ronetix iMX8MQ-CM
Engicam i.Core MX8M
Compulab iot-gate-imx8
- Fixes i.MX8 documentation
- Fixes phy usage with fec
|
|
By declaring board-specific board_fdt_chosen_bootargs() the kernel
command line arguments can be adjusted before injecting to flat dt
chosen node.
Signed-off-by: Niko Mauno <[email protected]>
|
|
It can be useful to use the same U-Boot binary for multiple purposes,
say the normal one, one for developers that allow breaking into the
U-Boot shell, and one for use during bootstrapping which runs a
special-purpose bootcmd. Or one can have several board variants that
can share almost all boot logic, but just needs a few tweaks in the
variables used by the boot script.
To that end, allow the control dtb to contain a /config/enviroment
node (or whatever one puts in fdt_env_path variable), whose
property/value pairs are used to update the run-time environment after
it has been loaded from its persistent location.
The indirection via fdt_env_path is for maximum flexibility - for
example, should the user wish (or board logic dictate) that the values
in the DTB should no longer be applied, one simply needs to delete the
fdt_env_path variable; that can even be done automatically by
including a
fdt_env_path = "";
property in the DTB node.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Rasmus Villemoes <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
This has the uclass enforce calling detect() before other methods. This
allows drivers to cache information in detect() and perform (cheaper)
retrieval in the other accessors. This also modifies the only instance
where this sequencing was not followed.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <[email protected]>
|
|
Console boot log:
U-Boot SPL 2021.04-00836-ga6232e065d-dirty (Apr 16 2021 - 15:16:35 +0200)
Trying to boot from MMC1
U-Boot 2021.04-00836-ga6232e065d-dirty (Apr 16 2021 - 15:16:35 +0200)
CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 44C
Reset cause: POR
Model: Ronetix iMX7-CM Board
Board: iMX7-CM
DRAM: 512 MiB
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address - fe:be:37:01:5a:3f
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Signed-off-by: Ilko Iliev <[email protected]>
|
|
Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate).
The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console
Signed-off-by: Kirill Kapranov <[email protected]>
Signed-off-by: Uri Mashiach <[email protected]>
Signed-off-by: Valentin Raevsky <[email protected]>
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: Peter Robinson <[email protected]>
|
|
Add a board_pci_fixup_dev weak function to allow PCI device fixups
during enumeration.
Signed-off-by: Tim Harvey <[email protected]>
|
|
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <[email protected]>
|
|
Prevent shell access on boot failure by entering an infinite
loop.
Signed-off-by: Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Minor cosmetic changes to unify `CONFIG_EXTRA_ENV_SETTINGS'
indentation between Bx50v3 and PPD to make comparison and
review easier and simplify the default boot command.
Signed-off-by: Ian Ray Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Remove unsupported USB boot.
Signed-off-by: Ian Ray <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
|
