| Age | Commit message (Collapse) | Author |
|---|
|
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <[email protected]>
|
|
PHY init
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 5980925e2a5a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Suman Anna <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
Add a command to show the available events.
Signed-off-by: Simon Glass <[email protected]>
|
|
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <[email protected]>
|
|
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <[email protected]>
|
|
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <[email protected]>
Cc: Pramod Kumar <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This slight environment modification shouldn't be in the CONFIG
namespace, change it.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOOTFILE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_POSTCLK_INIT
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_ECC_SUPPORT
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BIOSEMU
Cc: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_COMMON
Signed-off-by: Tom Rini <[email protected]>
|
|
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BTB
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a6b ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Implements SCMI APIs to retrieve the number exposed SCMI clocks using
SCMI_PROTOCOL_ATTRIBUTES messages and the names of the clocks using
SCMI_CLOCK_ATTRIBUTES messages.
This change updates sandbox SCMI clock test driver to manage these
2 new message IDs.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Clement Leger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Gabriel Fernandez <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Changes devm_scmi_process_msg() first argument from target parent device
to current SCMI device and lookup the SCMI agent device among SCMI device
parents for find the SCMI agent operator needed for communication with
the firmware.
This change is needed in order to support CCF in clk_scmi driver unless
what CCF will fail to find the right udevice related to exposed SCMI
clocks.
This patch allows to simplify the caller sequence, using SCMI device
reference as parameter instead of knowing SCMI uclass topology. This
change also adds some protection in case devm_scmi_process_msg() API
function is called for an invalid device type.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
|
|
This adds a helper function for clk_get_by_name in cases where the clock is
optional. Hopefully this helps point driver writers in the right direction.
Also convert some existing users.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This converts the existing driver API docs (clk-uclass.h) to kernel doc
format and adds them to the HTML documentation. Because the kernel doc
sphinx converter does not handle functions in structs very well, the
individual methods are documented separately. This is primarily inspired by
the phylink documentation [1], which uses this trick extensively.
[1] https://www.kernel.org/doc/html/latest/networking/kapi.html#c.phylink_mac_ops
Signed-off-by: Sean Anderson <[email protected]>
Tested-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This converts the existing client (aka clk.h) documentation to kernel doc
format, and adds it to the HTML docs. I have tried to preserve existing
comments as much as possible, refraining from semantic changes.
Signed-off-by: Sean Anderson <[email protected]>
Tested-by: Heinrich Schuchardt <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[rebased onto u-boot/master and resolved conflicts]
Signed-off-by: Sean Anderson <[email protected]>
|
|
The optional varients of clk_get_* functions are just simple wrappers.
Reduce code size a bit by inlining them. On platforms where it is not used
(most of them), it will not be compiled in any more. On platforms where
they are used, the inlined branch should not cause any significant growth.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This normalizes the name of this accessor function to put "_optional" last.
Signed-off-by: Sean Anderson <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
These symbols are incorrect, meaning that binman cannot find the
associated entry. This leads to errors like:
binman: Section '/binman/simple-bin': Symbol '_binman_spl_prop_size'
in entry '/binman/simple-bin/u-boot-spl/u-boot-spl-nodtb':
Entry 'spl' not found in list (mkimage,u-boot-spl-nodtb,
u-boot-spl-bss-pad,u-boot-spl-dtb,u-boot-spl,u-boot-img,main-section)
Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc3
microblaze:
- Fix exception handler
zynqmp:
- Show information about secure images
- DT changes (som u-boot file removal)
- Fix zynqmp_pm_cfg_obj_convert.py
- Fix platform boot
xilinx:
- Fix bootm_size calculation
- Remove GPIO_EXTRA_HEADER selection
power:
- Add zynqmp power management driver
scsi:
- Add phy support to ceva driver
zynq qspi:
- Fix unaligned accesses and check baudrate setup
- Add support for spi memory operations
net:
- Fix 64bit calculation in axi_emac
video:
- Add missing gpio dependency for seps driver
|
|
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Michael Walle <[email protected]>
|
|
Use the complete 512kb (4 blocks) nand partition reserved for u-boot
environment instead of just the first block, this allows the module to
have a working environment even if 3 blocks are bad.
Signed-off-by: Francesco Dolcini <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
Clean up config file:
- remove unnecessary IMX_FEC_BASE
- remove unnecessary comment
- remove ipaddr/serverip from env
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Add initial support for Advantech RSB-3720 board.
The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console
Signed-off-by: Darren Huang <[email protected]>
Signed-off-by: Kevin12.Chen <[email protected]>
Signed-off-by: Phill.Liu <[email protected]>
Signed-off-by: Tim Liang <[email protected]>
Signed-off-by: wei.zeng <[email protected]>
Signed-off-by: Ying-Chun Liu (PaulLiu) <[email protected]>
Cc: uboot-imx <[email protected]>
Cc: Peng Fan (OSS) <[email protected]>
|
|
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
|
|
This change updates all Armada 37xx DTS files to version which is used by
Linux kernel v5.18.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
PCI config space of the aardvark PCIe Root Port is available only in
internal aardvark memory space starting at offset 0x0. PCI Express
registers (PCI_EXP_*) start at offset 0xc0. And Advanced Error Reporting
registers (PCI_ERR_*) start at offset 0x100.
Replace custom aardvark register macros by standard PCI macros from
include/pci.h file with fixed offset.
Some DEVCTL and AER macros are not defined in include/pci.h file, so define
them in the same way as in linux uapi header file pci_regs.h.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Now that single defconfig can be used for booting J721E EVM and
SK, default device tree will not work for selecting dtb for
kernel. Update the findfdt env to select right dtb based on
board_name env variable.
Signed-off-by: Sinthu Raja <[email protected]>
|
|
This function has not been conditionally compiled for some time, so
remove the incorrect guards around the declaration.
Signed-off-by: Tom Rini <[email protected]>
|
|
Also, rename it to XILINX_MICROBLAZE0_DELAY_SLOT_EXCEP, since it only
covers delay slot exception support.
Signed-off-by: Ovidiu Panait <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Michal Simek <[email protected]>
|
|
Add command "zynqmp pmufw node close" to disable permission to load
additional pmufw config overlays. This command will make sure that any
other sw will ask for changing permission.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/cfa5cc7909eb8deb23eb0f11c26954cbaddeb861.1642163135.git.michal.simek@xilinx.com
|
|
Introduce zynqmp_pmufw_node() for loading PMU configuration fragment for
enabling IPs. Firmware driver has small overlay where NODE id is added and
config fragment is sent to PMUFW. There is a need to build PMUFW with
fragment support.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/636e8150bd4e2b1f988d59795772c685ceeec083.1642163135.git.michal.simek@xilinx.com
|
|
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
|
|
This function is used by both x86 and sandbox. Put it in a common header
file.
Signed-off-by: Simon Glass <[email protected]>
|
|
When parsing the dfu_alt_info, check the number of arguments
and argument string strictly. If there is any garbage data
(which is not able to be parsed correctly) in dfu_alt_info,
that means something wrong and user may make a typo or mis-
understanding about the syntax. Since the dfu_alt_info is
used for updating the firmware, this mistake may lead to
brick the hardware.
Thus it should be checked strictly for making sure there
is no mistake.
Signed-off-by: Masami Hiramatsu <[email protected]>
|
|
this will add kaslrseed keyword to sysboot lable,
when it set, it will request to genarate random number
from hwrng as kaslr-seed.
with this patch exlinux.conf label looks like
label l0
menu testing
linux /boot/vmlinuz-5.15.16-arm
initrd /boot/initramfs-5.15.16-arm.img
fdtdir /boot/dtbs/5.15.16-arm/
kaslrseed
append root=UUID=92ae1e50-eeeb-4c5b-8939-7e1cd6cfb059 ro
Tested on Khadas VIM with kernel 5.16.0-rc5-arm64, Debian 11.
Signed-off-by: Zhang Ning <[email protected]>
|
|
|
|
The imx8mm and imx8mn appear compatible with imx7d-usb
flags in the OTG driver. If the dr_mode is defined as
host or peripheral, the device appears to operate correctly,
however the auto host/peripheral detection results in an error.
The solution isn't just adding checks for imx8mm and imx8mn to
the check for imx7, because the USB clock needs to be running
to read from the USBNC_PHY_STATUS_OFFSET register or it will hang.
Marek requested that I not enable the clocks in ehci_usb_of_to_plat,
so I modified that function to return an unknown state if the
device tree does not explicitly state whether it is a host
or a peripheral.
When the driver probes, it looks to see if it's in the unknown
state, and only then will it read the register to auto-detect.
Signed-off-by: Adam Ford <[email protected]>
Tested-by: Tim Harvey <[email protected]>
|
|
There are no boards that define CONFIG_SYS_RESET_ADDR, so drop the
remaining comments referencing it and also the config_whitelist.txt entry.
Signed-off-by: Ovidiu Panait <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Acked-by: [email protected]
|
