| Age | Commit message (Collapse) | Author |
|---|
|
Allows one to set the processor clock rate via "setenv mpurate 720" for example
Default is set to a "safe" 500 Mhz.
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
This patch adds a function to allow one to easily set the target
voltage for the TWL4030 regulators. It also modifies the existing
code to use this new function. Applicable definitions are moved
out of the driver file and into the header file so that they are
generally accessible
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
|
|
|
|
This patch fixes a bug in reconfigure_pll(), where the detection of
the current bootstrap option is wrong. The ICS bits where incorrectly
shifted. This bug was found on the lwmon5 board, which uses bootstrap
option H (I2C bootstrap EEPROM).
Additionally a bit of code was moved into the if statement, since its
only used after later on. No need to run this code all the time.
Also, a few empty lines are added to make the code better readable.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Rupjyoti Sarmah <[email protected]>
Cc: Victor Gallardo <[email protected]>
|
|
Opps, after a long time I tested recent u-boot on our
APC405 board. This simple fix makes networking work again.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Albert Aribaud <[email protected]>
Acked-by: Prafulla Wadaskar<[email protected]>
Acked-by: Heiko Schocher<[email protected]>
|
|
These are not used on this board, which uses soft I2C instead.
Signed-off-by: Albert Aribaud <[email protected]>
Acked-by: Prafulla Wadaskar<[email protected]>
Acked-by: Heiko Schocher<[email protected]>
|
|
We get two build errors:
fsl_elbc_nand.c: In function 'fsl_elbc_run_command':
fsl_elbc_nand.c:231: error: 'fsl_lbc_t' has no member named 'lsor'
make[1]: *** [/work/wd/tmp-ppc/drivers/mtd/nand/fsl_elbc_nand.o] Error 1
and
ve8313.c: In function 'initdram':
ve8313.c:104: error: expected '=', ',', ';', 'asm' or '__attribute__'
before '*' token
ve8313.c:104: error: 'lbc' undeclared (first use in this function)
ve8313.c:104: error: (Each undeclared identifier is reported only once
ve8313.c:104: error: for each function it appears in.)
ve8313.c:104: error: 'immap_t' has no member named 'lbus'
make[1]: *** [ve8313.o] Error 1
make: *** [board/ve8313/libve8313.a] Error 2
Due to changes to unifiy local bus struct definitions.
Reported-by: Wolfgang Denk <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
The board specific parameters associated with quad rank dimms where
missing. This fixes it so the board will function if quad rank dimms
are placed in it.
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
|
|
Enabling USB HOST in defconfig.
Signed-off-by: Ajay Kumar Gupta <[email protected]>
|
|
Tested MSC Host on AM3517EVM.
Signed-off-by: Ajay Kumar Gupta <[email protected]>
|
|
Recent features enabled by default require a larger monitor size for the
cm-bf548 port, so bump it up a bit.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls
to take a (const char *) parameter instead of (char *), but in some cases
the modified functions call other functions taking (char *). The end result
is warnings about discarding the const qualifier.
This patch fixes these other function signatures.
Signed-off-by: Ben Warren <[email protected]>
|
|
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <[email protected]>
Acked-by: Dave Liu <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
This patch has the following fixes/changes:
- Set 'kernel_addr' and 'ramdisk_addr' to correct values and add
'fdt_addr' environment variable
- Remove 'kozio' environment variable
- Remove environmant variables to boot ancient arch/ppc Linux kernels
- Remove CONFIG_SYS_BOOTMAPSZ definition. It's already defined to
the same value in amcc-common.h
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size and default environment
after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
None of the AMCC boards uses an embedded environment, so there is no
need to run "saveenv" after updating U-Boot. Drop the redundant
commands from the default environment.
Signed-off-by: Wolfgang Denk <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Heiko Schocher <[email protected]>
|
|
- nfs-options removed
- hda->sda changed
- mtd parts added
- loadaddress changed
- cmd-line length increased
- lcd stuff removed
- code cleanup (use I/O accessors etc.)
Signed-off-by: Klaus Heydeck <[email protected]>
|
|
This patch enables mvsata driver and related filesystem support.
The patch is tested for ide reset and ext2ls operation for a disk drive connected on SATA port0.
This patch depends upon the patche-series http://lists.denx.de/pipermail/u-boot/2010-August/074908.html
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
Add mvsata_ide and cmd_ide configuration in edminiv2 config
Signed-off-by: Albert Aribaud <[email protected]>
|
|
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <[email protected]>
|
|
|
|
Specify vram on command line, remove erroneous call to nandboot
in the boot script, add CONFIG_BOOTDELAY
Signed-off-by: Steve Sakoman <[email protected]>
Acked-by: Nishanth Menon <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
This patch add the basic infrastructure for the TWL6030 driver and enables
support in the two existing OMAP4 boards, Panda and OMAP4430 SDP
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
The OMAP4 x-load code sets gptimer1 clock source to 32Khz. This isn't
acceptable for udelay. This patch changes from gptimer1 to gptimer2,
which uses sys_clk at 38.4 Mhz.
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Aneesh V <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function. This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).
Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.
To avoid confusion, rename into getenv_f() [as "running from flash"]
Signed-off-by: Wolfgang Denk <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
|
|
|
|
|
|
Adds the board_mmc_init function and enable the mmc command
Signed-off-by: Minkyu Kang <[email protected]>
Signed-off-by: Jaehoon Chung <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
|
|
because it's convenient.
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Add support for the P4080DS board, with the following features:
* 36-bit only
* Boots from NOR flash
* FMAN drivers NOT supported
* SPD DDR initialization
Signed-off-by: Ed Swarthout <[email protected]>
Signed-off-by: Emil Medve <[email protected]>
Signed-off-by: Becky Bruce <[email protected]>
Signed-off-by: Ashish Kalra <[email protected]>
Signed-off-by: Stuart Yoder <[email protected]>
Signed-off-by: Dave Liu <[email protected]>
Signed-off-by: Lan Chunhe-B25806 <[email protected]>
Signed-off-by: Scott Wood <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Roy Zang <[email protected]>
Signed-off-by: Timur Tabi <[email protected]>
Signed-off-by: Andy Fleming <[email protected]>
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
Enabled SPD
Enabled DDR2
Enabled hwconfig
Signed-off-by: York Sun <[email protected]>
|
|
Enabled registered DIMMs using data from SPD. RDIMMs have registers
which need to be configured before using. The register configuration
words are stored in SPD byte 60~116 (JEDEC standard No.21-C). Software
should read those RCWs and put into DDR controller before initialization.
Signed-off-by: York Sun <[email protected]>
|
