| Age | Commit message (Collapse) | Author |
|---|
|
The reason is enabling tftpput command where
tftp shorcut stops to work for tftpboot.
Signed-off-by: Michal Simek <[email protected]>
|
|
U-Boot names the Raspberry Pi board rpi_b. This means that the common
expression for DTB filename ${soc}-${board}.dtb expands to
bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is
bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts
look for the correct DTB filename.
An alternative would be to rename the U-Boot board to rpi-b. However,
that change would be far more invasive, and end up affecting users (i.e
they'd have to change their U-Boot build commands).
Signed-off-by: Stephen Warren <[email protected]>
|
|
|
|
|
|
Add L2 cache support and enable it by default.
Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Dirk Behme <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading
address to avoid overlaping), we need to adjust the fdt_addr in order to be
able to boot FSL 3.10 kernel.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <[email protected]>
|
|
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.
Cc: Lokesh Vutla <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <[email protected]>
Cc: Minkyu Kang <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Acked-by: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <[email protected]>
Cc: Pantelis Antoniou <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions. Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.
Cc: Pantelis Antoniou <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Signed-off-by: Rajeshwari S Shinde <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
Signed-off-by: Pantelis Antoniou <[email protected]>
|
|
Now that the designware ethernet driver uses phylib we need to turn it
on here.
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <[email protected]>
Cc: Vipin Kumar <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Mischa Jonker <[email protected]>
Cc: Shiraz Hashim <[email protected]>
Cc: Albert ARIBAUD <[email protected]>
Cc: Amit Virdi <[email protected]>
Cc: Sonic Zhang <[email protected]>
Signed-off-by: Alexey Brodkin <[email protected]>
|
|
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:
* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMAC
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Francois Bedard <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.
This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Francois Bedard <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Alexey Brodkin <[email protected]>
Cc: Vineet Gupta <[email protected]>
Cc: Francois Bedard <[email protected]>
Cc: Wolfgang Denk <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
This patch modifies envs to enable dual kernel boot
- with separated DTB if the DTB file is loaded successfully;
- with DTB apppended to uImage if DTB file is not found;
This is neccesssary for backward compatibilty.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Przemyslaw Marczak <[email protected]>
Acked-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Cc: Mateusz Zalega <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This patch sets envs that describe board information.
The following envs are set: soc_id, soc_rev, board_rev.
Based on this information, if CONFIG_OF_LIBFDT is enabled,
the 'fdtfile' env is set as:
fdtfile=${soc_family}${soc_id}-${board}.dtb
The generated envs are intenionally not saved to persistent storage.
Signed-off-by: Piotr Wilczek <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
With e0059ea switching to using SZ_1K, we need to #include <asm/sizes.h>
here for everyone to build still.
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Just extend tables with this new device.
Signed-off-by: Michal Simek <[email protected]>
|
|
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Eric Nelson <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Michael Schwingen <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
describe a set of default features that distros can rely on being available.
having this common definition means that distros can easily support systems
implementing them.
Signed-off-by: Dennis Gilmore <[email protected]>
|
|
|
|
|
|
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <[email protected]>
|
