| Age | Commit message (Collapse) | Author |
|---|
|
It speeds up writing a lot.
Signed-off-by: Michal Simek <[email protected]>
|
|
Command provides just dump subcommand for showing clock
frequencies in a soc.
Signed-off-by: Michal Simek <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Fix the timeout issue after running "bootp" command in U-Boot console.
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).
Signed-off-by: Jim Lin <[email protected]>
Signed-off-by: Stephen Warren <[email protected]>
Tested-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.
This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.
Signed-off-by: Tom Warren <[email protected]>
Signed-off-by: Stephen Warren <[email protected]>
Tested-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Tegra124's MMC controller is very similar to earlier SoC generations,
and can be supported by the same driver.
However, there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW. This
patch updates the driver to support that new compatible value.
That said, the HW differences are only relevant when enabling certain
high-performance transfer modes. Since the driver is currently very
simple and doesn't enable those modes, we don't actually need to address
any of these HW differences in the code yet, hence the simple nature of
this patch.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Pantelis Antoniou <[email protected]>
Tested-by: Thierry Reding <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
$usb_need_init prevents "usb start" from being run multiple times for
each boot attempt, i.e. once for USB storage, another for PXE, and
another for DHCP. However, the flag that's used to determine when to run
"usb start" is never cleared, so a subsequent "boot" command will never
probe for a freshly plugged in USB device. Fix this so that new USB
devices will be probed once per boot attempt.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The U-Boot "cardhu" build supports only revision 4 of the Cardhu board
and later compatible revisions. Hence, set $board_name in the default
environment to "cardhu-a04" rather than just "cardhu".
The Linux kernel has separate DTs for Cardhu A02 and A04, although the
former isn't really supported any more. Consequently, the kernel DT file
that matches the U-Boot cardhu build is "tegra30-cardhu-a04.dtb" rather
than "tegra30-cardhu.dtb". Set the $fdtfile default environment variable
to reflect this.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So update acessor functions with common IFC acessor functions to take care
both type of endianness.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.
Signed-off-by: Valentin Longchamp <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.
Signed-off-by: Valentin Longchamp <[email protected]>
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun <[email protected]>
|
|
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Valentin Longchamp <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <[email protected]>
Signed-off-by: Valentin Longchamp <[email protected]>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <[email protected]>
|
|
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <[email protected]>
|
|
Add usb2 node entry to hwconfig default
Remove DDR controller interleaving from hwconfig
Move SPI related macros out of "#ifdef CONFIG_SPIFLASH"
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot
Signed-off-by: Prabhakar Kushwaha <[email protected]>
[York Sun: Fix commit message]
Signed-off-by: York Sun <[email protected]>
|
|
Add usb2 node entry in "hwconfig string"
Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller
SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible
Signed-off-by: Poonam Aggrwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <[email protected]>
|
|
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
Define MDIO related configs
Added eth.c file
Update t1040.c to support RGMII and SGMII
Update t1040qds.c to support ethernet
Define the PHY address
Signed-off-by: Arpit Goel <[email protected]>
Signed-off-by: Bhupesh Sharma <[email protected]>
Signed-off-by: Poonam Aggrwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
Signed-off-by: Prabhakar Kushwaha <[email protected]>
[York Sun: remove dash from commit message]
Signed-off-by: York Sun <[email protected]>
|
|
This change allows updating environment stored on MMC by dfu or thor.
New setting:
- "params.bin mmc 0x38 0x8"
File params.bin can be generated by: tools/mkenvimage.
e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file>
Every new env variable in text file should start with a new line.
Sample env text file:
- board/samsung/common/dfu_sample_env.txt
Requirements:
- file name: "params.bin"
- file size: 4096 Bytes - the same as CONFIG_ENV_SIZE.
Other size will cause CRC miscalculation at boot.
Signed-off-by: Przemyslaw Marczak <[email protected]>
CC: Piotr Wilczek <[email protected]>
CC: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Przemyslaw Marczak <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
This simple LCD menu allows run one of download mode on device
without writing on console or for fast and easy upgrade.
This feature check user keys combination at boot:
- power key + volume up - download menu
- power key + volume down - thor mode (without menu)
New configs:
- CONFIG_LCD_MENU
- CONFIG_LCD_MENU_BOARD
For proper effect this feature needs following definitions:
Power key:
- KEY_PWR_PMIC_NAME - (string) pmic which supports power key check
Register address:
- KEY_PWR_STATUS_REG
- KEY_PWR_INTERRUPT_REG
Register power key mask:
- KEY_PWR_STATUS_MASK
- KEY_PWR_INTERRUPT_MASK
Gpio numbers:
- KEY_PWR_INTERRUPT_MASK
- KEY_VOL_DOWN_GPIO
Functions needs to be called:
- keys_init() - for set proper gpio direction
- check_boot_mode() - menu - main function
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
16 bpp mode is required by LCD console mode.
This change updates exynos board files.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Changes:
- check image bpp instead of resolution when returns logo address
- remove 32bpp logo
- add 16bpp logo in two formats: bmp and gzipped bmp
- init logo address with "0" for unsupported bpp mode
- update boards configs with proper image size for gunzip
- extend structure vidinfo by two fields: logo_x_offset and logo_y_offset.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Tested-by: Hyungwon Hwang <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Changes:
new file:
- board/samsung/common/misc.c
depends on: CONFIG_MISC_COMMON
- move draw_logo() to misc.c
configs: trats, trats2, universal:
- enable CONFIG_MISC_COMMON,
- enable CONFIG_MISC_INIT_R,
- add misc_init_r() and call draw_logo() in it.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Remove wrong and unused env variables
Trats2 is not as GT-I8800.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Acked-by: Jaehoon Chung <[email protected]>
Cc: Piotr Wilczek <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
|
|
|
|
Enable CONFIG_REGEX on M53EVK to allow usage of regular expressions
on environment variables.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
The name the Linux kernel expects is 'mxc_nand' , not 'mxc-nand' .
This patch renames the driver name.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Stefano Babic <[email protected]>
Acked-by: Stefano Babic <[email protected]>
|
|
Enable PCI express on MX6 Sabrelite.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Eric Nelson <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>
|
|
Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot
Signed-off-by: Dan Murphy <[email protected]>
|
|
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <[email protected]>
|
|
Move the FAT functions to a common location for reuse.
Signed-off-by: Dan Murphy <[email protected]>
|
|
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The function os_free() returns nothing.
Its return type should be "void" rather than "void *".
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
We do not have to define CONFIG_MPC512X in board config headers
because it is defined in arch/powerpc/cpu/mpc512x/config.mk.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.
include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Like other architectures, CONFIG_AVR32 can be defined
in arch/avr32/config.mk rather than board header files.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Acked-by: Andreas Bießmann <[email protected]>
|
|
Commit 643aae1406c93ddc64fcf8c136b47cdffd9c8ccd
deleted include/linux/config.h but missed to
delete _LINUX_CONFIG_H macro.
It is no longer used at all.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Upon further inspection of relevant parts of the architecture, the
maximum SPL binary size is 220KiB.
Cc: Lokesh Vutla <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
To reduce code duplication update omap3_igep00x0.h to use ti_omap3_common.h.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
|
|
Create a new file, include/configs/ti_omap3_common.h, for everything
common to the OMAP3 SoC leaving just the board specific part to board
configuration file.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
|
|
If CONFIG_NR_DRAM_BANKS is not defined, we say (for simplicity) that we have
1 bank, but for some boards should be interesting that we can define
CONFIG_NR_DRAM_BANKS. To handle this possibility just define the number of
DRAM banks if is not already defined. This is useful for some OMAP3 boards
where the DRAM initialitzation is only at u-boot level.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
|
