| Age | Commit message (Collapse) | Author |
|---|
|
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <[email protected]>
|
|
Signed-off-by: Valeriy Glushkov <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
Signed-off-by: Valeriy Glushkov <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <[email protected]>
Cc: Dave Liu <[email protected]>
Cc: Ron Madrid <[email protected]>
Cc: Anton Vorontsov <[email protected]>
|
|
Add a bootargs for M53017EVB and update bootargs
for M54451EVB
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Remove individual CPU specific DSPI driver.
Add required feature for the common DSPI driver in cpu_init and
in platform configuration file.
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Increase the flash size from 8MB to 16MB
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Update M52277EVB, M53017EVB and M54455EVB platform configuration
file to use flash buffer write
Signed-off-by: TsiChung Liew <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
Needed for Rev. 2 silicon at 400 MHz
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Reinhard Arlt <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Peter Pearse <[email protected]>
Cc: Catalin Marinas <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Peter Pearse <[email protected]>
Cc: Catalin Marinas <[email protected]>
|
|
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <[email protected]>
|
|
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <[email protected]>
|
|
The current defition for CKEN_B register bits is nonsense. Adding 32 to
the shifted value is equal to '| (1 << 5)', and this bit is marked
'reserved' in the PXA docs.
Signed-off-by: Daniel Mack <[email protected]>
|
|
This clock is needed for systems using the USB2 device unit or the 2d
graphics accelerator.
Signed-off-by: Daniel Mack <[email protected]>
|
|
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Matthias Fuchs <[email protected]>
|
|
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <[email protected]>
Acked-by: Nobuhiro Iwamatsu <[email protected]>
Acked-by: Andy Fleming <[email protected]>
Acked-by: Andre Schwarz <[email protected]>
Acked-by: Kim Phillips <[email protected]>
|
|
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <[email protected]>
Acked-by: Grant Likely <[email protected]>
|
|
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
fix a stray CONFIG_MPC83XX that escaped commit
0f898604945af4543c1525fc33b6bae621a3b805.
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
|
This patch use blackfin errno.h implementation which
correspond Linux kernel one.
MIPS implemetation is different that's why I keep it.
I removed ppc_error_no.h from Marvell boards which
was the same too.
I have got ack from ppc40x, blackfin, arm, coldfire and avr custodians.
Acked-by: Stefan Roese <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
|
|
|
|
Signed-off-by: Heiko Schocher <[email protected]>
|
