| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_S3C6400 is must defined at config header file
That definition is unnecessary at this file
Signed-off-by: Minkyu Kang <[email protected]>
|
|
|
|
|
|
The size of U-Boot binary for MPC8360ERDK increased
(> 2 flash sectors now), so 'saveenv' will partially
overwrite U-Boot in flash and will brick the board.
This patch moves environment offset to fourth flash
sector and also fixes CONFIG_SYS_MONITOR_LEN.
Signed-off-by: Anatolij Gustschin <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
Change netdev.h to use CONFIG_ULI526X instead of CONFIG_ULI526. CONFIG_ULI526X
is used everywhere else, so that's the correct macro name. Without this fix,
Ethernet will not work on the Freescale MPC8610 HPCD.
Signed-off-by: Timur Tabi <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
Update the DaVinci DM6446 boards to use the new convention
for CONFIG_SYS_NS16550_REG_SIZE ... the size hasn't changed
from the original 4 bytes, but these chips are little-endian.
(Resolves a regression added recently by the include/ns16550.h
patch to "Unify structure declaration for registers". The code
previously worked just fine because the registers were accessed
as host-endian words, not as bytes.)
Signed-off-by: David Brownell <[email protected]>
|
|
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Tested-by: Sergey Lapin <[email protected]>
Tested-by: Eric BENARD <[email protected]>
|
|
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
calculate dynamically the clock rate and pllb setting for usb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <[email protected]>
|
|
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <[email protected]>
|
|
|
|
Signed-off-by: Mike Frysinger <[email protected]>
|
|
This Patch adds Support for PXA27X UDC.
(Rebased to drivers/usb reorganisation)
Signed-off-by: Vivek Kutal <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
|
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Remy Bohmer <[email protected]>
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
unify arm cache management except for non standard cache as ARM7TDMI
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
import system.h from linux
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
This patch fix the wrong gpio offset
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.
Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.
Signed-off-by: Kyungmin Park <[email protected]>
|
|
Signed-off-by: Tom Rix <[email protected]>
|
|
|
|
This brings it in line with other Freescale boards.
Signed-off-by: Scott Wood <[email protected]>
|
|
On platforms with multiple NOR chips, currently only the first one
can be selected using the "ubi part" command. This patch fixes this
problem by using different names for the NOR "mtd devices".
It also changes the name of the NOR MTD device from "cfi-mtd" to
"norX" (X indexing the device numer) to better match the mtdparts
defaults.
Signed-off-by: Stefan Roese <[email protected]>
Signed-off-by: Andreas Huber <[email protected]>
|
|
Signed-off-by: Mingkai Hu <[email protected]>
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Acked-by: Stelian Pop <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
add CONFIG_AT91RM9200_USART to activate the driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
Signed-off-by: Nicolas Ferre <[email protected]>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
|
|
|
|
This is required so that the MAC address will be updated in the device tree.
Signed-off-by: Scott Wood <[email protected]>
|
|
PCI on PQ2FADS is very similar to PCI on MPC8272ADS.
Signed-off-by: Scott Wood <[email protected]>
|
|
Signed-off-by: Kumar Gala <[email protected]>
|
|
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <[email protected]>
|
|
Some systems have zlib.h installed in /usr/include/. This isn't the
desired file for u-boot code - we want the one in include/zlib.h.
This rename will avoid the conflict.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
Signed-off-by: Mike Frysinger <[email protected]>
|
|
Instead of special casing the different access patterns, use common
code with light macros sprinkled in to accomodate for the different
layouts of the register structure.
Note that this also changes the types of the registers for the
"positively packed (>1)" cases. As the registers truly are unsigned
chars, this is surely the Right Thing, but it is a semantic change.
Note that for this case depending on the endianness on the bus, we may
see a change of behaviour.
Signed-off-by: Detlev Zundel <[email protected]>
|
|
Add support for compiling the host tools in the tools directory using
the MinGW toolchain. This produces executables which can be used on
standard Windows computers without requiring cygwin.
One must specify the MinGW compiler and strip utilities as if they
were the host toolchain in order to build win32 executables, eg:
make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
Signed-off-by: Peter Tyser <[email protected]>
|
|
The original code provided an incomplete set of typedefs for WIN32
compiles and replicated the standard typedefs that are already
provided by stdint.h
Signed-off-by: Peter Tyser <[email protected]>
|
|
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <[email protected]>
|
|
|
|
|
|
Fix problems introduced in commit
7b5611cdd12ca0cc33f994f0d4a4454788fc3124 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.
Also eliminate redundant definitions in ps2mult.h. More cleanup will
be needed for other redundant occurrences though.
Signed-off-by: Detlev Zundel <[email protected]>
|
|
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
Since the Blackfin timer code requires HZ to be 1000, barf on any board
that tries to use a different value.
Signed-off-by: Mike Frysinger <[email protected]>
|
