| Age | Commit message (Collapse) | Author |
|---|
|
Overlapped with fdt_addr*, thus corrupted the latter when using both.
Signed-off-by: Jan Kiszka <[email protected]>
|
|
With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.
Signed-off-by: Michal Simek <[email protected]>
|
|
With multi defconfig targeting several board configurations bug report like
below is so verbose.
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
0 Bytes
Do not report that message and simply say "Flash: 0 Bytes" because most of
Zynq boards are using different type of flashes than NOR.
Signed-off-by: Michal Simek <[email protected]>
|
|
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Jerome Brunet <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Import the common leds bindings definition from linux
d5226fa6dbae ("Linux 5.5")
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Jerome Brunet <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
- Add support for Jetson Nano, plus miscellaneous other fixes found
during Nano bringup.
- Add Igor's update_uboot wrapper patches.
|
|
The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
Tested-by: Peter Robinson <[email protected]>
|
|
The L4T kernel is 32MB+, and can overwrite the ramdisk/fdt loaded
from extlinux.conf. Adjust the load addresses to fix this for now.
Using the calculated_env addresses table from T186 U-Boot is a
better fix, but it isn't working correctly on T210 U-Boot right now,
so this will do until I can fix it.
Signed-off-by: Tom Warren <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra30 colibri_t30.img.cfg colibri_t30.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage(NAND).
Create an proper tegra image:
$ cbootimage -s tegra20 colibri_t20-512-v12-nand.img.cfg colibri_t20.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra30 apalis_t30.img.cfg apalis_t30.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.
Create an proper tegra image:
$ cbootimage -s tegra124 apalis-tk1.img.cfg apalis-tk1.img
Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot
Signed-off-by: Igor Opaniuk <[email protected]>
Reviewed-by: Oleksandr Suvorov <[email protected]>
|
|
Enable config options and console setting to respective
rk3399 board for HDMI output.
Boards supported and tested on this patch are:
- NanoPc T4
- NanoPi M4
- NanoPi Neo4
- ROC-RK3399-PC
- Rock960
Cc: Manivannan Sadhasivam <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Tested-by: Peter Robinson <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
These are used in multiple places so update them to use a shared #define.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Philippe Reynes <[email protected]>
|
|
This should mention that conf_uname can be NULL and should be in the
header file. Fix this.
Signed-off-by: Simon Glass <[email protected]>
|
|
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc5
This series fixes:
* UEFI Python tests CONFIG_OF_CONTROL=y.
* int to pointer cast warning for cmd/efidebug.c
* memory reservation even if fdt node is disabled
Now that the Python test is fixed reintroduce the reverted patch for
vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
|
|
Change to use SOCFPGA_PHYS_OCRAM_SIZE macro for onchip RAM size.
Signed-off-by: Ley Foon Tan <[email protected]>
|
|
MC_INIT and BOOT command currently access spi-nor flash memory directly.
As per spi-mem framework, flash memory access via absolute addresses is
no more possible. Use flash APIs to access memory instead of directly
using it.
Signed-off-by: Kuldeep Singh <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Adjust environment kernel_addr_r from 0x96000000 to 0x92000000
to fix a bug that failed to boot kernel for ls1012afrwy with 512MiB RAM,
=> tftpboot $kernel_addr_r Image (Image size is 36 MiB)
TFTP error: trying to overwrite reserved memory...
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This patch appends othbootargs to bootargs for LS1021ATWR board.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Fix wrong environment variable of board for ls1012afrwy
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Move the environment variables from command head file to
ls1028ardb specific head file so that they will not mess
up with ls1028aqds board.
Also updated some variable slightly.
There is no function change by this patch.
Signed-off-by: Yuantian Tang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add sd and emmc bootcmd environments to facilitate
the boot process.
Signed-off-by: Yuantian Tang <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add support of distro boot for ls2080aqds
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add support of distro boot for ls1088aqds
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
The old load address of itb will overwrite uboots reserved memory
on ls1012afrwy with 512 MiB ram
Signed-off-by: Biwen Li <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add dhcp in supported boot_targets for lx2160.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Add DHCP boot target device to enable command bootcmd_dhcp.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Update the secure boot headers offsets of Kernel and other
firmware images for SD and XSPI boot sources used by
esbc_validate command.
Signed-off-by: Priyanka Singh <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add emmc in supported boot_targets and
Add bootcmd environment variable for emmc boot.
Signed-off-by: Meenakshi Aggarwal <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Setting fdt_high and initrd_high to 0xffffffffffffffff leads to
various difficulty to resolve bugs.
Remove them and use bootm_size instead to safely contain a kernel,
device tree and initrd for relocation.
Signed-off-by: Yuantian Tang <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This patch sets CONFIG_SYS_BOOTMAPSZ to the amount of memory available
to safely contain a kernel, device tree and initrd for relocation. The
way to set fdt_high as 0xffffffff to disable device tree relocation is
removed.
Signed-off-by: Alison Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <[email protected]>
|
|
EFI was disabled in f95b8a4b5f64f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <[email protected]>
|
|
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5965e5bb2bcad1c53ca8419b428ff6d.
Signed-off-by: Tom Rini <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip
- Fixed for rv1108 and elgin-rv1108 board
- Fix the keyboard from USB instead of CrOS EC
|
|
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <[email protected]>
Reviewed-by: Michael Trimarchi <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <[email protected]>
Acked-by: Patrice Chotard <[email protected]>
|
|
EFI was disabled in f95b8a4b5f64f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <[email protected]>
|
|
'vendor' is both an input and an output parameter. So it cannot be
constant.
Fixes: 0bda81bfdc5c ("efi_loader: use const efi_guid_t * for variable services")
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti into next
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- i2c-gpio: make it possible to run deblock sequence on driver probe
- i2c-gpio: add clock stretching support
- updates the Designware I2C driver for high speed mode,
fix a bug and add some improvements.
- add DM support for memory based bootcounter driver
|
|
See UEFI specification, section 8.5.3.
In addition, the structure, efi_capsule_header, should be "packed"
as it is a serialized binary format in a capsule file.
Signed-off-by: AKASHI Takahiro <[email protected]>
|
|
This is a preparatory patch.
Those functions will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <[email protected]>
|
|
Some of those values will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <[email protected]>
|
