| Age | Commit message (Collapse) | Author |
|---|
|
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <[email protected]>
Tested-by: Sylvain Lemieux <[email protected]>
|
|
|
|
|
|
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit 2afddae07523f23f77acd066ad1719f53d289f98.
Signed-off-by: Simon Glass <[email protected]>
|
|
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <[email protected]>
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
This patch enabled the MVEBU PCIe support on the db-88f6820-gp A38x
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Anton Schubert <[email protected]>
Cc: Luka Perkov <[email protected]>
Cc: Dirk Eibach <[email protected]>
|
|
This patch enabled the MVEBU PCIe support on the db-mv784mp-gp AXP
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Anton Schubert <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
the ECC SDRAM scrubbing that needs to be done in the main U-Boot.
The SPL (previously bin_hdr) has already scrubbed the area:
0x0000.0000 - 0x0100.0000
In this area this main U-Boot needs to get loaded. The main U-Boot
then can scrub the remaining SDRAM area while running from this
location.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
This patch adds support for multiple hostcontrollers to the ehci-marvell driver
and enables all 3 usb-hcs on the db-mv784mp-gp board.
It depends on the initial Armada XP usb support patch from Stefan.
Signed-off-by: Anton Schubert <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
This patch enabled the USB/EHCI support for the Marvell
DB-MV784MP-GP Armada XP eval board.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Anton Schubert <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Luka Perkov <[email protected]>
|
|
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
|
|
Also update maintainer info.
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Also update maintainer info.
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: York Sun <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Wolfgang Denk <[email protected]>
|
|
The default boot command searches for dofastboot varaiable
and does a fastboot if it is set to 1.
But the condition "if test ${dofastboot} -eq 1" always
returns true if dofastboot is not defined and breaking mmc boot.
So make dofastboot as 0 by default and let the runtime
environment set it if fastboot is required.
Reported-by: Yan Liu <[email protected]>
Signed-off-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
At present we have a simple assignment to gd. With some archs this is
implemented as a register or through some other means; a simple assignment
does not suit in all cases.
Change this to a function and add documentation to describe how this all
works.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: York Sun <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <[email protected]>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <[email protected]>
Cc: Przemyslaw Marczak <[email protected]>
Cc: Simon Glass <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
These functions allow iteration through all PCI devices including bridges.
The children of each PCI bus are returned in turn. This can be useful for
configuring, checking or enumerating all the devices.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
At present there are no PCI functions which allow access to PCI
configuration using a struct udevice. This is a sad situation for driver
model as it makes use of PCI harder. Add these functions.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
|
|
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Tested-by: Bin Meng <[email protected]>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <[email protected]>
|
|
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Signed-off-by: Bin Meng <[email protected]>
|
|
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Signed-off-by: Bin Meng <[email protected]>
|
|
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Add support for making the visual area of the framebuffer smaller and
drawing a black border around it. This is intended for use with
overscanning monitors (esp. with composite video out), to avoid part
of the picture being invisible.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
Acked-by: Anatolij Gustschin <[email protected]>
|
|
Represent all available RAM in either one or two banks. The first bank
describes any RAM below 4GB. The second bank describes any RAM above 4GB.
This split is driven by the following requirements:
- The NVIDIA L4T kernel requires separate entries in the DT /memory/reg
property for memory below and above the 4GB boundary. The layout of that
DT property is directly driven by the entries in the U-Boot bank array.
- On systems with RAM beyond a physical address of 4GB, the potential
existence of a carve-out at the end of RAM below 4GB can only be
represented using multiple banks, since usable RAM is not contiguous.
While making this change, add a lot more comments re: how and why RAM is
represented in banks, and implement a few more "semantic" functions that
define (and perhaps later detect at run-time) the size of any carve-out.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The new value is the most likely value where the kernel wants to end up
at run-time. Selecting this value as the load address likely avoids the
need to copy the kernel image from the actual load address to the desired
load address. Note that this isn't guaranteed since the kernel may wish
to run at an arbitrary location. In that case, U-Boot will still relocate
the image according to its wishes; this change is a performance
optimization, not a hard-coding of the final image location.
Signed-off-by: Stephen Warren <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Various clean-ups either in comments, order or spacing without any
functional impact:
- Add some comments in the device trees resp. reorder some parameters
for consistency across all our modules.
- Sort some include files alphabetically (while leaving common.h on
top of course).
- Streamline some comments in the configuration files and fix the
spacing from using spaces to tabs.
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Enable CONFIG_IP_DEFRAG and set CONFIG_TFTP_BLOCKSIZE to 16384.
This increases the tftp download speed considerably.
While at it enable CONFIG_TFTP_TSIZE which limits the progress bar to
fifty '#' independent of the downloaded file size.
Signed-off-by: Max Krummenacher <[email protected]>
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Now as all is in place actually enable UBI/UBIFS support to be able to
boot the Linux kernel and root file system from NAND.
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Enable mtdparts aka dynamic MTD partition support.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add I2C support in order to subsequently allow disabling the PMIC sleep
mode on low supply voltage.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Add LCD display support defaulting to VESA VGA resolution. Different
resolutions configurable via device tree.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Allow detecting whether or not U-Boot was launched through the
recovery mode of the resp. NVIDIA SoC.
Make use of a board specific arch_misc_init() and enable the same via
CONFIG_ARCH_MISC_INIT configuration option.
Signed-off-by: Marcel Ziswiler <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Allow for optional custom USB gadget manufacturer/product/vendor
IDs/strings to be specified.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Acked-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Remove spurious new line in configuration file.
Signed-off-by: Marcel Ziswiler <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
9MB reserved for initrd is not enough for default ramfs used for keystone
devices, which is ~33MB. This patch increases the size up to 80MB.
Signed-off-by: Vitaly Andrianov <[email protected]>
|
|
This patch set the correct initrd address to much rdaddr, which used at
get_fs_ramfs commad.
Fixes: 3e97f0b63c8e ("configs: ti_armv7_keystone2: switch addresses
to generic addresses")
Signed-off-by: Vitaly Andrianov <[email protected]>
|
|
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: Stefano Babic <[email protected]>
Cc: Igor Grinberg <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <[email protected]>
|
