summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2009-07-06arm nomadik: use 1000 as HZ value and rewrite timer codeAlessandro Rubini
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites timer code, which is now both correct and much smaller. Unused functions like udelay_masked() have been removed as no driver uses them, even the ones that are not currently active for this board. mtu.h is copied literally from the kernel sources. Signed-off-by: Alessandro Rubini <[email protected]> Acked-by: Andrea Gallo <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06arm nomadik: allow Nand and OneNand to coexistsAlessandro Rubini
The evaluation kit has both Nand and OneNand, both drivers are there and the two configurations only select a different default for the jffs partition. This adds the OneNand driver and cleans up storage. Signed-off-by: Alessandro Rubini <[email protected]> Acked-by: Andrea Gallo <[email protected]>
2009-07-06arm nomadik: cleanup resetAlessandro Rubini
There is only one public release of the Nomadik chip, so the ifdef in reset code as well as a define in the config file are not needed Signed-off-by: Alessandro Rubini <[email protected]> Acked-by: Andrea Gallo <[email protected]>
2009-07-06arm nomadik: rename board to nhk8815Alessandro Rubini
This is an error in my side in the initial submission: nobody calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead. Signed-off-by: Alessandro Rubini <[email protected]> Acked-by: Andrea Gallo <[email protected]>
2009-07-06xscale: add support for the polaris boardStefano Babic
The Polaris board is based on the TrizepsIV module of Keith & Koep (http://www.keith-koep.com). Signed-off-by: Stefano Babic <[email protected]>
2009-07-06at91: Add esd gmbh MEESC board supportDaniel Gorsulowski
This patch adds support for esd gmbh MEESC board. The MEESC is based on an Atmel AT91SAM9263 SoC. Signed-off-by: Daniel Gorsulowski <[email protected]>
2009-07-06ARM: Update mach-typesJean-Christophe PLAGNIOL-VILLARD
update against linux v2.6.30 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06at91: Add CAN init functionDaniel Gorsulowski
To enable CAN init, CONFIG_CAN has to be defined in the board config file and at91_can_hw_init() has to be called in the board specific code. CAN is available on AT91SAM9263 and AT91CAP9 SoC. Signed-off-by: Daniel Gorsulowski <[email protected]>
2009-07-06arm: Kirkwood: Correct header defineSimon Kagstrom
Correct define typo (. -> ,) Signed-off-by: Simon Kagstrom <[email protected]>
2009-07-06MX31: Add basic support for Freescale i.MX31 PDK board.Magnus Lilja
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board). This patch assumes that some other program performs the actual NAND boot. Signed-off-by: Magnus Lilja <[email protected]> Acked-by: Fabio Estevam <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06S3C24x0: extract interrupts from timerJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06dm355/pm9261: add missing CONFIG_NET_MULTIJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06move L2 cache enable/disable function to cache.c in the omap3 SoC directoryKim, Heung Jun
Signed-off-by: HeungJun, Kim <[email protected]> CC: Dirk Behme <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-07-06versatile: config coding style cleanupJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Cc: Peter Pearse <[email protected]>
2009-07-06arm: Kirkwood: Basic SOCs supportPrafulla Wadaskar
Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core. SOC versions supported:- 1) 88F6281-A0 define CONFIG_KW88F6281_A0 2) 88F6192-A0 define CONFIG_KW88F6192_A0 Other supported features:- 1) get_random_hex() fucntion 2) PCI Express port initialization 3) NS16550 driver support Contributors: Yotam Admon <[email protected]> Michael Blostein <[email protected] Reviewed-by: Ronen Shitrit <[email protected]> Acked-by: Stefan Rose <[email protected]> Signed-off-by: Prafulla Wadaskar <[email protected]>
2009-07-06arm: generic cache.h for ARM architecturesPrafulla Wadaskar
This patch is required for Kirkwood SoC support may be used by other ARM architectures Signed-off-by: Prafulla Wadaskar <[email protected]>
2009-07-06OMAP3EVM: fix typo. replace CS6 by CS5, no functionality changeMatthias Ludwig
Signed-off-by: Matthias Ludwig <[email protected]>
2009-07-0283xx: Add support for fsl_dma driverPeter Tyser
Signed-off-by: Peter Tyser <[email protected]> Reviewed-by: Ira W. Snyder <[email protected]> Tested-by: Ira W. Snyder <[email protected]> Acked-by: Kim Phillips <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-028xxx: Second UART port added for MPC85xx, MPC83xx, MPC86xx processorsPoonam Aggrwal
Defining the next two configs allows to switch the serial port from the console using the setenv stdin and stdout 1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */ 2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ Signed-off-by: Poonam Aggrwal <[email protected]> Signed-off-by: Ed Swarthout <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-0285xx: Adds GPIO registers to MPC85xx Memory Map.Poonam Aggrwal
Signed-off-by: Poonam Aggrwal <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-0186xx: XPedite5170 board supportPeter Tyser
Initial support for Extreme Engineering Solutions XPedite5170 - a MPC8640-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-01fsl_dma: Break out common memory initialization functionPeter Tyser
Signed-off-by: Peter Tyser <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-01fsl_dma: Move dma function prototypes to common header filePeter Tyser
Signed-off-by: Peter Tyser <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-01fsl_dma: Add bitfield definitions for common registersPeter Tyser
Signed-off-by: Peter Tyser <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-07-018xxx: Break out DMA code to a common filePeter Tyser
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the previous CONFIG_DDR_ECC Signed-off-by: Peter Tyser <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-06-3085xx: Add pci e1000 Ethernet support for P2020 boardRoy Zang
Signed-off-by: Roy Zang <[email protected]> Signed-off-by: Kumar Gala <[email protected]>
2009-06-308xxx: Fix PCI bus address setup for 36-bit configsKumar Gala
We want the outbound PCI memory map to end at the 4G boundary so we can maximize the amount of space available for inbound mappings if we have large amounts of memory. This matches the device tree setup in the kernel for the 36-bit physical configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS). Signed-off-by: Kumar Gala <[email protected]>
2009-06-3086xx: Add CPU_TYPE_ENTRY supportKumar Gala
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use this to convey the # of cores and DDR width in the near future so its good to keep in sync. Signed-off-by: Kumar Gala <[email protected]>
2009-06-26spi: Add Marvell Kirkwood SPI driverPrafulla Wadaskar
This patch adds a SPI driver for the Marvell Kirkwood SoC's. Signed-off-by: Prafulla Wadaskar <[email protected]>
2009-06-23integratorap/cp: use cfi driverJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> Acked-by: Peter Pearse <[email protected]>
2009-06-21serial_mx31: allow it to work with mx27 too and rename to serial_mxcIlya Yanok
UART hardware on i.MX27 is the same as on the i.MX31 so we just need to provide the driver with correct address of the registers. Signed-off-by: Ilya Yanok <[email protected]>
2009-06-21mx27: basic cpu supportIlya Yanok
This patch adds generic code to support Freescale's i.MX27 SoCs. Signed-off-by: Ilya Yanok <[email protected]>
2009-06-21i.MX31: Create a common device file.Magnus Lilja
Signed-off-by: Magnus Lilja <[email protected]>
2009-06-21ARM: Add macros.h to be used in assembler file.Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-21MX31: Add NAND SPL for i.MX31.Magnus Lilja
This patch adds the NAND SPL framework needed to boot i.MX31 boards from NAND. It has been tested on a i.MX31 PDK board with large page NAND. Small page NANDs should work as well, but this has not been tested. Note: The i.MX31 NFC uses a non-standard layout for large page NANDs, whether this is compatible with a particular setup depends on how the NAND device is programmed by the flash programmer (e.g. JTAG debugger). The patch is based on the work by Maxim Artamonov. Signed-off-by: Maxim Artamonov <[email protected]> Signed-off-by: Magnus Lilja <[email protected]>
2009-06-21at91: unify nor boot supportJean-Christophe PLAGNIOL-VILLARD
the lowlevel init sequence is the same so unify it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-21at91sam9263ek: add nor flash supportJean-Christophe PLAGNIOL-VILLARD
this will allow you to store use it for the env and to boot directly U-Boot from Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-21at91: add support for the PM9261 board of Ronetix GmbHIlko Iliev
The PM9261 board is based on the AT91SAM9261-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9261.html Signed-off-by: Ilko Iliev <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-21pm9263: use macro instead of hardcode value for the lowlevel_initJean-Christophe PLAGNIOL-VILLARD
optimize a few the RAM init Signed-off-by: Ilko Iliev <[email protected]> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-21pm9263: lowlevel init updateJean-Christophe PLAGNIOL-VILLARD
move PSRAM init to pm9263.c this will allow us after to make the nor lowlevel_init generic Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
2009-06-15Blackfin: fix SPI flash speed define nameMike Frysinger
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards. Signed-off-by: Mike Frysinger <[email protected]>
2009-06-15Blackfin: bf548-ezkit: bump up monitor sizeMike Frysinger
The latest version of U-Boot got a bit fatter in the BSS section which caused overflows in the RAM region, so increase the monitor size. Signed-off-by: Mike Frysinger <[email protected]>
2009-06-15Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flashVivi Li
The SPI flash layer is much stricter about sector usage than the eeprom layer we used to use, so update the env settings to better match the sector alignment of the flashes we use. Signed-off-by: Vivi Li <[email protected]> Signed-off-by: Mike Frysinger <[email protected]>
2009-06-15Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2009-06-15Convert DM9000 driver for CONFIG_NET_MULTIRemy Bohmer
All drivers need to be converted to CONFIG_NET_MULTI. This patch converts the dm9000 driver. Signed-off-by: Thomas Smits <[email protected]> Signed-off-by: Remy Bohmer <[email protected]> Signed-off-by: Ben Warren <[email protected]>
2009-06-15net: Add Marvell Kirkwood gigabit ethernet driverPrafulla Wadaskar
This patch adds a egiga driver for the Marvell Kirkwood SoC's. Contributors: Yotam Admon <[email protected]> Michael Blostein <[email protected] Reviewed-by: Ronen Shitrit <[email protected]> Acked-by: Stefan Rose <[email protected]> Signed-off-by: Prafulla Wadaskar <[email protected]> Signed-off-by: Ben Warren <[email protected]>
2009-06-15DaVinci Network Driver Updates[email protected]
Different flavours of DaVinci SOC's have differences in their EMAC IP This patch does the following 1) Updates base addresses for DM365 2) Updates MDIO frequencies for DM365 and DM646x 3) Update EMAC wrapper registers for DM365 and DM646x Patch applies to u-boot-net git. the EMAC driver itself will be updated shortly to add support for DM365 and DM646x Signed-off-by: Sandeep Paulraj <[email protected]> Signed-off-by: Ben Warren <[email protected]>
2009-06-15Switched davinci_emac Ethernet driver to use newer APIBen Warren
Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <[email protected]>
2009-06-15Marvell MV88E61XX Switch Driver supportPrafulla Wadaskar
Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported for:- default or router port vlan configuration led_init configuration mdip/n polarity reversal configuration Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon <[email protected]> Michael Blostein <[email protected] Reviewed by: Ronen Shitrit <[email protected]> Signed-off-by: Prafulla Wadaskar <[email protected]> Signed-off-by: Ben Warren <[email protected]>
2009-06-15tsec: Add support for BCM5482S PHYZach LeRoy
Signed-off-by: Zach LeRoy <[email protected]> Acked-by: Kumar Gala <[email protected]> Signed-off-by: Ben Warren <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-07-26 20:44:27 +0000