| Age | Commit message (Collapse) | Author |
|---|
|
This allows for more flexible and standardized boot across multiple
platforms.
Remove redundant legacy boot environment.
Cc: Otavio Salvador <[email protected]>
Signed-off-by: Vagrant Cascadian <[email protected]>
|
|
This allows for more flexible and standardized boot across multiple
platforms.
Remove redundant legacy boot environment.
Signed-off-by: Vagrant Cascadian <[email protected]>
|
|
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <[email protected]>
Signed-off-by: Alexandre Courbot <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This needs a separate compatible value from Tegra124 since the new HW
version has bugs that would prevent a driver for previous HW versions
from operating at all.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
On the target board:
=> dfu 0 mmc 0
On the host PC:
$ dfu-util -l
Found DFU: [0525:a4a5] devnum=0, cfg=1, intf=0, alt=0, name="image"
Found DFU: [0525:a4a5] devnum=0, cfg=1, intf=0, alt=1, name="u-boot"
Found DFU: [0525:a4a5] devnum=0, cfg=1, intf=0, alt=2, name="bootimg"
Found DFU: [0525:a4a5] devnum=0, cfg=1, intf=0, alt=3, name="rootfs"
Update with a full SD image
$ dfu-util -a image -D core-image-minimal-imx7dsabresd.sdcard
Update u-boot only
$ dfu-util -a u-boot -D u-boot.imx
Signed-off-by: Tzu-Jung Lee <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
|
|
Rename board nios2-generic to 3c120_devboard. Since nios2 is
converted to driver model and device tree control of u-boot,
the nios2-generic board directory is removed. We can rename
the board back to a real board name. Now the boards maintained
in u-boot mainline are the same as Linux kernel, namely 3c120
and 10m50.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Zap the altera_tse_initialize() prototypes, since it is converted
to driver model.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Do not allocate rx buf in net.c, because altera_tse allocates
its own rx buf in driver. This can save 6KB memory.
Signed-off-by: Thomas Chou <[email protected]>
|
|
Use cfi flash driver model.
Signed-off-by: Thomas Chou <[email protected]>
|
|
Implement a Memory Technology Device (MTD) uclass. It should
include most flash drivers in the future. Though no uclass ops
are defined yet, the MTD ops could be used.
The NAND flash driver is based on MTD. The CFI flash and SPI
flash support MTD, too. It should make sense to convert them
to MTD uclass.
Signed-off-by: Thomas Chou <[email protected]>
|
|
|
|
Now that we have solved the problems that prevented this feature from
being enabled, enable it everywhere.
Signed-off-by: Stephen Warren <[email protected]>
|
|
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
The tricorder and tricorder_flash boards have grown too big.
Reduce their size by building them with CONFIG_SYS_THUMB_BUILD.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
This target is ARMv7-M therefore can only build for Thumb,
but it did not #define CONFIG_SYS_THUMB_BUILD, so the U-Boot
code did not know it had to build for Thumb(2), not ARM.
This patch is binary-invariant: builds of stm32f429-discovery
with and without this patch were compared and found to differ
only by their U-Boot version strings.
Signed-off-by: Albert ARIBAUD <[email protected]>
|
|
A number of headers define functions as "extern inline" which is
causing problems with gcc5. The reason is that starting with
version 5.1, gcc defaults to the standard C99 semantics for the
inline keyword.
Under the traditional GNU inline semantics, an "extern inline"
function would never create an external definition, the same
as inline *without* extern in C99. In C99, and "extern inline"
definition is simply an external definition with an inline hint.
In short, the meanings of inline with and without extern are
swapped between GNU and C99.
The upshot is that all these definitions in header files create
an external definition wherever those headers are included,
resulting in multiple definition errors at link time.
Changing all these functions to "static inline" fixes the problem
since this works as desired in all gcc versions. Although the
semantics are slightly different (a static inline definition may
result in an actual function being emitted), it works as intended
in practice.
This patch also removes extern prototype declarations for the
changed functions where they existed.
Signed-off-by: Mans Rullgard <[email protected]>
|
|
|
|
Trim CONFIG_SYS_MEMTEST_END location.
CONFIG_SYS_MONITOR_LEN
Reserving 256k for U-Boot at: d7fc0000
CONFIG_ENV_SIZE
CONFIG_SYS_MALLOC_LEN
Reserving 256k for malloc() at: d7f80000
0x10000 for the rest
Reserving 68 Bytes for Board Info at: d7f7ffbc
Reserving 208 Bytes for Global Data at: d7f7feec
Reserving 12000 Bytes for FDT at: d7f7d00c
Stack
Signed-off-by: Thomas Chou <[email protected]>
|
|
Trim CONFIG_SYS_MALLOC_LEN size, because CONFIG_ENV_SIZE
is included to total memory allocation in common.h,
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Chin Liang See <[email protected]>
|
|
Remove CONFIG_SYS_INIT_SP macro, as the initial stack is set to
below the u-boot code.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Chin Liang See <[email protected]>
|
|
Remove CONFIG_SYS_MALLOC_BASE macro, as it is not used by
the generic board.
Signed-off-by: Thomas Chou <[email protected]>
Reviewed-by: Chin Liang See <[email protected]>
|
|
Clean up macros that do not need a value as suggested by
Marek.
Signed-off-by: Thomas Chou <[email protected]>
Tested-by: Marek Vasut <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Use dram bank in board info, so that it displays correct
memory values in bdinfo command.
Signed-off-by: Thomas Chou <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Many SPI flashes have protection bits (BP2, BP1 and BP0) in the
status register that can protect selected regions of the SPI NOR.
Take these bits into account when performing erase operations,
making sure that the protected areas are skipped.
Tested on a mx6qsabresd:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
=> sf protect lock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
offset 0x3f0000 is protected and cannot be erased
SF: 65536 bytes @ 0x3f0000 Erased: ERROR
=> sf protect unlock 0x3f0000 0x10000
=> sf erase 0x3f0000 0x10000
SF: 65536 bytes @ 0x3f0000 Erased: OK
Signed-off-by: Fabio Estevam <[email protected]>
[re-worked to fit the lock common to dm and non-dm]
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Add fls_long and __ffs64 support to align with the kernel bitops
implementation.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Use the generic bitops header files from the kernel.
Imported from kernel 4.2.3.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Use the log2 header files from the kernel.
Imported from kernel 4.2.3.
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
|
|
|
|
|
|
|
|
DEV_EXT_VIDEO does not have any actual meaning, hence drop it.
Signed-off-by: Bin Meng <[email protected]>
|
|
DEV_FLAGS_SYSTEM does not have any actual meaning, hence drop it.
Signed-off-by: Bin Meng <[email protected]>
|
|
Commit: sandbox: add ADC driver
adds the driver without its main header file.
It causes build brake for sandbox_defonfig.
This commit adds a missing header:
- include/sandbox-adc.h
Signed-off-by: Przemyslaw Marczak <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Adding fdtdec_get_uint function which is the
unsigned version for fdtdec_get_int
Signed-off-by: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Stefan Roese <[email protected]>
Cc: Vikas Manocha <[email protected]>
Cc: Jagannadh Teki <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
|
|
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Update this driver to use driver model and change all users.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Production boards should not use CONFIG_OF_EMBED. Fix this for the Zybo
boards.
The image to use now becomes u-boot-dtb.bin.
For example, the .bif file should contain a line like:
[load = 0x04000000,startup=0x04000000]/path/to/u-boot-dtb.bin
instead of:
[load = 0x04000000,startup=0x04000000]/path/to/u-boot.bin
When device tree is enabled we need to load u-boot-dtb.img. Change the
settings so that SPL does the right thing.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
At present in SPL we place the device tree immediately after BSS. This
avoids needing to copy it out of the way before BSS can be used. However on
some boards BSS is not placed with the image - e.g. it can be in RAM if
available.
Add an option to tell U-Boot that the device tree should be placed at the
end of the image binary (_image_binary_end) instead of at the end of BSS.
Note: A common reason to place BSS in RAM is to support the FAT filesystem.
We should update the code so that it does not use so much BSS.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
It is sometimes useful to find a property in the chosen node. Add a function
for this.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Enable CONFIG_SYS_I2C_ZYNQ only if it has either I2C0 or I2C1
enabled in a board config.This fixes the issue of i2c error
during board init if board specific doesnt have either I2C0
or I2C1.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
This adds support to update firmware on qspi flash using DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D MLO -a MLO
$ sudo dfu-util -D u-boot.img -a u-boot.img
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Daniel Gorsulowski <[email protected]>
|
|
On T1040D4RDB board, u-boot fails to connect port FM1@DTSEC3 to
the Ethernet PHY because the wrong PHY address is used. Also,
T1040D4RDB supports SGMII on one port only.
Signed-off-by: Codrin Ciubotariu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Signed-off-by: Yangbo Lu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
