summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2020-06-22arm: wandboard: move CONFIG_MXC_UART to defconfigHeinrich Schuchardt
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in the .config file. To avoid duplicate definitions move the setting from include/configs/wandboard.h to configs/wandboard_defconfig. Document the debug UART settings in the README. Signed-off-by: Heinrich Schuchardt <[email protected]> Reviewed-by: Fabio Estevam <[email protected]>
2020-06-22colibri_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22colibri_imx7: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22apalis_imx6: boot env configuration updatesIgor Opaniuk
1. Drop legacy emmcboot wrapper from env. 2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP 3. Drop DFU defines Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22apalis-tk1: enable distrobootIgor Opaniuk
1. Use distro_bootcmd as default boot command instead of legacy emmcboot wrapper. 2. Drop emmcboot and sdboot wrappers. 3. Provide proper boot order for Distro Boot. Signed-off-by: Igor Opaniuk <[email protected]>
2020-06-22configs/colibri_vf.h: drop sdboot in favour of distro_bootcmdMax Krummenacher
The distro bootscript uses kernel_image to get the file name of the kernel, so change that variable name. UBI boot has precedence in the default boot command. If one wants to boot from SD with a working NAND installation stop in U-Boot and enter: setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd Signed-off-by: Max Krummenacher <[email protected]>
2020-06-22colibri-imx6ull/imx7: define bootubipart for distro bootStefan Agner
When using distro boot to boot from UBI volumes the boot partition has been hardcoded to "UBI" (capital letters). However, our default MTD layout uses "ubi" (lower case letter). Define "ubi" as the default UBI partition for distro boot for Toradex. This allows to use distro boot without having to redefine the MTD partition layout which is useful for TorizonCore. Signed-off-by: Stefan Agner <[email protected]>
2020-06-22colibri_imx7: add addresses required for distro bootStefan Agner
Define addresses required for full distro boot support. Signed-off-by: Stefan Agner <[email protected]>
2020-06-22colibri-imx8x: declare consoleargsOleksandr Suvorov
Store all console-related kernel parameters in dedicated variable. Signed-off-by: Oleksandr Suvorov <[email protected]>
2020-06-22mx6cuboxi: Convert to DM_ETHFabio Estevam
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet Driver Model. This also brings the benefit of restoring Ethernet functionality. Reported-by: Tom Rini <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Tested-by: Tom Rini <[email protected]>
2020-06-20Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini
2020-06-18ARM: rmobile: Increase PHY auto-negotiation timeout to 20sMarek Vasut
The ethernet PHY on all known Gen3 boards takes a while to come out of reset, increase the auto-negotiation timeout to prevent it from timing out in case the ethernet is used right after the board was reset. Signed-off-by: Marek Vasut <[email protected]> Cc: Nobuhiro Iwamatsu <[email protected]>
2020-06-18colibri_imx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Acked-by: Igor Opaniuk <[email protected]>
2020-06-18apalis_imx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Acked-by: Igor Opaniuk <[email protected]>
2020-06-18cm_fx6: fix video stdout in default environmentAnatolij Gustschin
After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <[email protected]> Cc: Nikita Kiryanov <[email protected]>
2020-06-15Merge tag 'efi-2020-07-rc5' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc5 Use correct printf code in efi_image_parse(). Add random number generation to HTML documentation.
2020-06-15mmc: fsl_esdhc: workaround for hardware 3.3v IO reliability issueYangbo Lu
When eSDHC operates at 3.3v, damage can accumulate in an internal level shifter at a higher than expected rate. The faster the interface runs, the more damage accumulates. This issue now is found on LX2160A eSDHC1 for only SD card. The hardware workaround is recommended to use an on-board level shifter that is 1.8v on SoC side and 3.3v on SD card side. For boards without hardware workaround, this option could be enabled, ensuring 1.8v IO voltage and disabling eSDHC if no card. This option assumes no hotplug, and u-boot has to make all the way to to linux to use 1.8v UHS-I speed mode if has card. If you do not want the workaround for better user experience, of course you can choose to not select it running eSDHC in unsafe mode. Signed-off-by: Yangbo Lu <[email protected]> Acked-by: Peng Fan <[email protected]>
2020-06-14doc: random number generationHeinrich Schuchardt
Add random number generation APIs to the HTML documentation. Fix style issues. Signed-off-by: Heinrich Schuchardt <[email protected]>
2020-06-11arm: Remove pcm051 boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Lars Poeschel <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-11arm: Remove omap3_pandora_defconfig boardJagan Teki
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Acked-by: Grazvydas Ignotas <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-11spi: davinci: Drop non-dm codeJagan Teki
Now all boards which are using davinci SPI driver have moved to SPL_DM so drop the unneeded non-dm code. Cc: Adam Ford <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Tested-by: Adam Ford <[email protected]> #da850-evm
2020-06-11ks2_evm: Switch to DM_SPL, SPL_OF_CONTROLJagan Teki
This would make SPL build to DM_SPL, SPL_OF_CONTROL. Build fine with but not tested. Cc: Vitaly Andrianov <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-06-09Merge tag 'u-boot-imx-20200609' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.07 ----------------- - mx53: mx53menlo Convert to DM_ETH, fix fail boot - imx8mp_evk: fix boot issue - MX6, display5: fix environment - drop warnings (watchdog) for i.MX8mm i.mx8mp - enable bootaux for i.MX8M Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/695929999
2020-06-08imx: imx8mp_evk: fix boot issuePeng Fan
The u-boot-spl.bin pad with ddr firmware conflicts with the CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten by malloc in SPL stage and cause ddr initialization not able to finish. So update the related addresses to fix the issue. Reported-by: Fabio Estevam <[email protected]> Signed-off-by: Peng Fan <[email protected]> Signed-off-by: Fabio Estevam <[email protected]>
2020-06-08imx: Update MTD partitions layout for display5 (i.MX6Q) boardLukasz Majewski
This change updates the MTD partition layout on SPI-NOR memory for display5 board. Signed-off-by: Lukasz Majewski <[email protected]>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-06-04Convert CONFIG_BOARD_LATE_INIT to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BOARD_LATE_INIT Signed-off-by: Tom Rini <[email protected]>
2020-06-04Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <[email protected]>
2020-06-04Convert CONFIG_BZIP2 et al to KconfigTom Rini
This converts the following to Kconfig: CONFIG_BZIP2 CONFIG_GZIP CONFIG_LZO CONFIG_ZLIB CONFIG_LZMA CONFIG_LZO Signed-off-by: Tom Rini <[email protected]>
2020-06-04topic_miami: Disable GPIOTom Rini
Per the boards config header file, there is no useful GPIO on these boards. Remove CONFIG_CMD_GPIO from the defconfigs. Cc: Mike Looijmans <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04ARM: rmobile: blanche: Disable CONFIG_CMD_SF / CONFIG_CMD_SPITom Rini
The config header for this platform disables both CMD_SF and CMD_SPI and the defconfig leaves them enabled. Disable them from the defconfig and enable them in the header. Cc: Marek Vasut <[email protected]> Cc: Masakazu Mochizuki <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04bcmstb: Migrate CONFIG_CMD_EXT[24]Tom Rini
The common config header for bcm7260 and bcm7445 enable CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the commands being disabled. Enable them via the defconfig. Cc: Thomas Fitzsimmons <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04mx6memcal: Finish migration to defconfig optionsTom Rini
The config header for this platform uses '#undef' in a number of cases. All of the MMC related ones were already handled correctly in the defconfig file. In the case of CONFIG_CMD_FUSE, the command was being built and enabled via defconfig. Disable it in the defconfig, cleanup the header. Reviewed-by: Eric Nelson <[email protected]> Signed-off-by: Tom Rini <[email protected]>
2020-06-04pfla02: Rework excluding NAND from SPLTom Rini
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD options to defconfig and rework the guards to not try and call the function in SPL builds. Cc: Stefano Babic <[email protected]> Signed-off-by: Tom Rini <[email protected]> Acked-by: Stefano Babic <[email protected]>
2020-06-04serial: Convert ARM_DCC to KconfigTom Rini
The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <[email protected]> Cc: Michal Simek <[email protected]> Cc: Tom McLeod <[email protected]> Cc: Mike Looijmans <[email protected]> Signed-off-by: Tom Rini <[email protected]> Reviewed-by: Luca Ceresoli <[email protected]>
2020-06-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscvTom Rini
- Fixes 7e249bc13aaf: ("riscv: Move all SMP related SBI calls to SBI_v01") Move sbi_probe_extension() out of CONFIG_SBI_V01. - SiFive FU540 support SPL.
2020-06-04sifive: fu540: Add sample SD gpt partition layoutJagan Teki
This is a sample GPT partition layout for SD card, right now three important partitions are added to make the system bootable. partition layout: Part Start LBA End LBA Name Attributes Type GUID Partition GUID 1 0x00000022 0x00000821 "loader1" attrs: 0x0000000000000000 type: 5b193300-fc78-40cd-8002-e86c45580b47 guid: cbcbef44-e627-42bc-b134-93b6f3784b8c 2 0x00000822 0x00002821 "loader2" attrs: 0x0000000000000000 type: 2e54b353-1271-4842-806f-e436d6af6985 guid: f54eba28-d8de-4852-978d-1a673777e2ae 3 0x00002822 0x00020821 "rootfs" attrs: 0x0000000000000004 type: 0fc63daf-8483-4772-8e79-3d69d8477de4 type: linux guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93 Note: - loader1 would be fsbl or spl - loader2 would be U-Boot or U-Boot proper Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Bin Meng <[email protected]> Reviewed-by: Pragnesh Patel <[email protected]>
2020-06-04riscv: sifive: fu540: add SPL configurationPragnesh Patel
Add a support for SPL which will boot from L2 LIM (0x0800_0000) and then SPL will boot U-Boot FIT image (OpenSBI FW_DYNAMIC + u-boot.bin) from MMC boot devices. SPL related code is leveraged from FSBL (https://github.com/sifive/freedom-u540-c000-bootloader.git) Signed-off-by: Pragnesh Patel <[email protected]> Reviewed-by: Bin Meng <[email protected]> Tested-by: Bin Meng <[email protected]> Reviewed-by: Jagan Teki <[email protected]> Tested-by: Jagan Teki <[email protected]>
2020-06-03Merge tag 'efi-2020-07-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc4 This patch series addresses the following issues: * allow compiling with clang * add missing function descriptions to the HTML documentation * simplify the validation of UEFI images * validate load options in the UEFI boot manager In a preparatory patch a structure definition is moved.
2020-06-03Merge https://gitlab.denx.de/u-boot/custodians/u-boot-spiTom Rini
- Toshiba spinand (Yoshio) - SPI/SPI Flash cleanup (Jagan) - Remove SH SPI (Jagan)
2020-06-03efi_loader: validate load optionHeinrich Schuchardt
For passing the optional data of the load option to the loaded imaged protocol we need its size. efi_deserialize_load_option() is changed to return the size of the optional data. As a by-product we get a partial validation of the load option. Checking the length of the device path remains to be implemented. Some Coverity defects identified the load options as user input because get_unaligned_le32() and get_unaligned_le16() is called. But non of these Coverity defects can be resolved without marking functions with Coverity specific tags. Reported-by: Coverity (CID 303760) Reported-by: Coverity (CID 303768) Reported-by: Coverity (CID 303776) Signed-off-by: Heinrich Schuchardt <[email protected]>
2020-06-02dma-mapping: Add header file for ARCH_DMA_MINALIGNSimon Glass
This is defined in the asm/cache.h header file. Update this header file to include it. Signed-off-by: Simon Glass <[email protected]> Reviewed-by: Tom Rini <[email protected]> Tested-by: Adam Ford <[email protected]> #da850-evm
2020-06-01sf: Drop spl_flash_get_sw_write_protJagan Teki
The get_sw_write_prot API is used to get the write-protected bits of flash by reading the status register and other wards it's API for reading register bits. 1) This kind of requirement can be achieved using existing flash operations and flash locking API calls instead of making a separate flash API. 2) Technically there is no real hardware user for this API to use in the source tree. 3) Having a flash operations API for simple register read bits also make difficult to extend the flash operations. 4) Instead of touching generic code, it is possible to have this functionality inside spinor operations in the form of flash hooks or fixups for associated flash chips. Considering all these points, this patch drops the get_sw_write_prot and associated code bases. Cc: Simon Glass <[email protected]> Cc: Vignesh R <[email protected]> Signed-off-by: Jagan Teki <[email protected]>
2020-05-31rockchip: Add initial support for the Pinebook Pro laptop from Pine64.Peter Robinson
Specification: - Rockchip RK3399 - 4GB Dual-Channel LPDDR4 - eMMC socket - mSD card slot - 128Mbit (16Mb) SPI Flash - AP6256 for 11AC WiFi + BT5 - 14 inch 1920*1080 eDP MiPi display - Camera - USB 3.0, 2.0 ports - Type-C port with alt-mode display (DP 1.2) and 15W charge - DC 5V/3A - optional PCIe slot for NVMe SSD drive Signed-off-by: Peter Robinson <[email protected]> Tested-by: Vagrant Cascadian <[email protected]> Reviewed-by: Kever Yang <[email protected]> Signed-off-by: Kever Yang <[email protected]>
2020-05-31dt-bindings: input: adopt Linux gpio-keys binding constantsPeter Robinson
Sync the gpio-keys input bindings from linux 5.7-rc1. Signed-off-by: Peter Robinson <[email protected]>
2020-05-29usb: dwc3: amend UTMI/UTMIW phy interface setupFrank Wang
Let move 8/16-bit UTMI+ interface initialization into DWC3 core init that is convenient for both DM_USB and u-boot traditional process. Signed-off-by: Frank Wang <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-05-29usb: dwc3: Add disable u2mac linestate check quirkJagan Teki
This patch adds a quirk to disable USB 2.0 MAC linestate check during HS transmit. Refer the dwc3 databook, we can use it for some special platforms if the linestate not reflect the expected line state(J) during transmission. When use this quirk, the controller implements a fixed 40-bit TxEndDelay after the packet is given on UTMI and ignores the linestate during the transmit of a token (during token-to-token and token-to-data IPGAP). On some rockchip platforms (e.g. rk3399), it requires to disable the u2mac linestate check to decrease the SSPLIT token to SETUP token inter-packet delay from 566ns to 466ns, and fix the issue that FS/LS devices not recognized if inserted through USB 3.0 HUB. Reference from below Linux commit, commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate check quirk") Cc: Marek Vasut <[email protected]> Signed-off-by: Jagan Teki <[email protected]> Reviewed-by: Kever Yang <[email protected]>
2020-05-29usb: dwc3: add dis_u2_freeclk_exists_quirkFrank Wang
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit, which specifies whether the USB2.0 PHY provides a free-running PHY clock, which is active when the clock control input is active. Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk") in Linux Rockchip Kernel. Signed-off-by: Frank Wang <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Jagan Teki <[email protected]> Tested-by: Jagan Teki <[email protected]>
2020-05-29usb: dwc3: add dis_enblslpm_quirkFrank Wang
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls whether the PHY receives the suspend signal from the controller. Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk") in Linux Kernel. Signed-off-by: Frank Wang <[email protected]> Reviewed-by: Kever Yang <[email protected]> Reviewed-by: Jagan Teki <[email protected]> Tested-by: Jagan Teki <[email protected]>
generated by cgit v1.3.1 (git 2.54.0) at 2026-07-24 01:26:20 +0000