| Age | Commit message (Collapse) | Author |
|---|
|
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <[email protected]>
Signed-off-by: Vitaly Wool <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Signed-off-by: Tom Rini <[email protected]>
Conflicts:
include/configs/imx6qdl_icore_rqs.h
include/configs/imx6ul_geam.h
include/configs/imx6ul_isiot.h
|
|
This reverts commit ddb3ac3c716f56cead695444e65a7ba7b0946555.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
The SPL_MAX_SIZE is the internal memory size minux the space
used by bootrom.
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Philipp Tomsich <[email protected]>
|
|
since commit: f8b7fff1d5c5 "serial: atmel_usart: Add clk support"
corvus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
As all x86 boards have been switched over to use DM USB, remove
CONFIG_USB_MAX_CONTROLLER_COUNT which is not used by DM USB.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Tested-by: Stefan Roese <[email protected]>
|
|
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Tested-by: Stefan Roese <[email protected]>
|
|
|
|
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <[email protected]>
|
|
Decrease malloc size to 1MB from 256MB. Huge malloc
space is adding huge delay in mem_malloc_init() because
we are enabling CONFIG_SYS_MALLOC_CLEAR_ON_INIT
which clear the whole malloc space.
Signed-off-by: Michal Simek <[email protected]>
|
|
CPU_RELEASE_ADDR is used only when CONFIG_ARMV8_MULTIENTRY
is enabled. ZynqMP is running ATF which takes care about this
that's why no need to have this macro.
Signed-off-by: Michal Simek <[email protected]>
|
|
Remove the CONFIG_DM_I2C_COMPAT config.
Signed-off-by: Jaehoon Chung <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
we removed 5xx support. So delete some forgotten remains.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
we removed 82xx support. Missed some 82xx remains,
remove them now.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
To prevent possible double inclusions in future.
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
For better readability and setup-handling we refactor the default
environment.
Signed-off-by: Hannes Schmelzer <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Hannes Schmelzer <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
This define isn't used anymore in the u-boot source tree, so we drop it
from the config header.
We drop it also from the 'config_whitelist.txt'
Signed-off-by: Hannes Schmelzer <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
the BMP logo loading has become obsolete and is not used any more. So we
drop the support for it.
Signed-off-by: Hannes Schmelzer <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brxre1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Jean-Jacques Hiblot <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
The terminator endif of ifdef _NAND_H_ should be at the
end of file as a fail safe.
Signed-off-by: Mugunthan V N <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Grygorii Strashko <[email protected]>
|
|
|
|
|
|
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <[email protected]>
|
|
Signed-off-by: York Sun <[email protected]>
|
|
Enable DHCP command to make TFTP easier.
Enable DDR interactive debug by default.
Signed-off-by: York Sun <[email protected]>
|
|
Use eMMC (instead of SD card) to store U-Boot environment. Use
"reserved" partition for U-Boot environment.
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
|
|
Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).
[1] 7a53a1a8115b ARM: ti: Update layout for MMC and eMMC (env and dfu)
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).
[1] 7a53a1a8115b ARM: ti: Update layout for MMC and eMMC (env and dfu)
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <[email protected]>
|
|
|
|
When we don't have CONFIG_BLK defined we don't have a forward
declaration of struct udevice, and thus get a warning about it on
blk_get_from_parent(), which we only have when CONFIG_BLK is set. Move
the declaration of blk_get_from_parent() to be with the other CONFIG_BLK
parts.
Fixes 9f103b9cb5f8 ("dm: blk: Add a way to obtain a block device from ...")
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
As only FIT image is supported now, this patch is to support loading
32-bit uImage, dtb and rootfs separately.
Signed-off-by: Alison Wang <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
Signed-off-by: Tom Rini <[email protected]>
|
|
Show the U-Boot banner and board information on the video display during
boot.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present CP15 init is disabled on tegra. Use the correct option so that
this init is performed on boot. This enables the instruction cache, for
example, which is critical to the machine running at full speed.
Signed-off-by: Simon Glass <[email protected]>
|
|
As per the datasheet[1] available for DDR2 part on board
the OMAP-L138 LCDK, the tXSNR (exit self refresh to a
non-read command) is 137.5 ns. This corresponds to a
value of 20 to be written to T_XSNR register field of
OMAP-L138's DDR configuration. The DDR2 is at 150 MHz.
Fix this. The correct value also appears on the initialization
scripts (called CCS GEL files) available on TI's wiki pages[2]
[1] http://www.samsung.com/global/business/semiconductor/file/product/ds_k4t1gxx4qf_rev12-0.pdf
[2] http://processors.wiki.ti.com/index.php/L138/C6748_Development_Kit_(LCDK)#CCS_XML_.26_GEL_Files
Signed-off-by: Sekhar Nori <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
There is some inconsistency between uses of CONFIG_RTC_DS13xx and
CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from
these variables.
Signed-off-by: Chris Packham <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <[email protected]>
|
|
Signed-off-by: Vikas Manocha <[email protected]>
|
