| Age | Commit message (Collapse) | Author |
|---|
|
The using the bitops is too easy controlling than now.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
To maintain consistency, set_ios type of legacy mmc_ops changed to int.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
This quirk doesn't need anymore.
It's replaced to get_cd callback function.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Some SoCs can have their own card dect scheme.
Then they may use this get_cd callback function after implementing init
in their drivers.
Signed-off-by: Jaehoon Chung <[email protected]>
|
|
Move configuration option from board file to defconfig.
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
|
|
DNL numbers are not changed that's why fastboot needs to be called with
-i parameter (Xilinx vendor id).
- Show available devices
sudo fastboot -i 0x03fd devices
xilinx_zynqmp_zcu100 fastboot
- Stop fastboot and go back to U-Boot prompt
sudo fastboot -i 0x03fd continue
- Reboot the board
sudo fastboot -i 0x03fd reboot
- Get internal variables
sudo fastboot -i 0x3fd getvar bootloader-version
bootloader-version: U-Boot 2016.07-00026-g19bd53044817
sudo fastboot -i 0x3fd getvar downloadsize
downloadsize: 0x06000000
sudo fastboot -i 0x3fd getvar version
version: 0.4
(regular variables needs to have fastboot. prefix - there is also
serialno variable which should be define as serial#)
- Format SD/MMC/EMMC card
sudo fastboot -i 0x3fd oem format
- Write images to boot and Linux partition
sudo fastboot -i 0x3fd flash boot sd.img
sudo fastboot -i 0x3fd flash Linux os.img
- Creating sd.img or os.img
$ dd if=/dev/zero of=sd.img bs=1024 count=1024
$ mkfs.vfat sd.img
$ mkdir sd-mount
$ mount -o loop sd.img sd-mount
$ echo foo > sd-mount/bar
$ umount sd-mount
partitions setting should be checked by running gpt command.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Do the same change which was done in ZynqMP by:
"ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP"
(sha1: a8b6a156c0f7fb99502229e454bc9c3b38645280)
Signed-off-by: Michal Simek <[email protected]>
|
|
Enable CONFIG_SYS_TEXT_BASE via Kconfig.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Increase environment size to 32K as the current default
environment itself is greater than 4K.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Enable overwriting variables out of main config file.
Signed-off-by: Michal Simek <[email protected]>
|
|
IP addresses shouldn't be hardcoded in board config.
This patch removes them.
Signed-off-by: Michal Simek <[email protected]>
|
|
wait_for_bit() is missing reset watchdog in case watchdog
is configured.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Since usb ether gadget have support for driver model, so enable
usb ether gadget.
Signed-off-by: Mugunthan V N <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Adopt usb ether gadget and rndis driver to adopt driver model
Signed-off-by: Mugunthan V N <[email protected]>
|
|
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <[email protected]>
|
|
|
|
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <[email protected]>
|
|
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig to select errata workaround.
Signed-off-by: York Sun <[email protected]>
|
|
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <[email protected]>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <[email protected]>
|
|
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <[email protected]>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use TARGET_T2081QDS from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use TARGET_T2080RDB from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use TARGET_T2080QDS from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use TARGET_T1040QDS from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <[email protected]>
|
|
Use TARGET_T1023RDB from Kconfig instead.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.
Signed-off-by: York Sun <[email protected]>
|
|
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <[email protected]>
|
|
Use Kconfig option for E500 and E500MC macros.
Signed-off-by: York Sun <[email protected]>
|
|
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Alexander Graf <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The UL() macro is pretty useful in sharing constants between assembly
and C files while still being able to specify a type for C.
Move the macro from an armv8 specific header into a common header file
to be able to use it by arm code (for instance) as well.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Alexander Graf <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Alexander Graf <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Acked-by: Maxime Ripard <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
|
|
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
- Add tab space
- remove exctra 'mmc dev ${mmcdev}'
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Create ubifs.img:
$ mkfs.ubifs -q -r /rootfs -m 4096 -e 253952 -c 7936 -o ubifs.img
Write ubifs.img:
---------------
icorem6qdl> nand erase.part rootfs
icorem6qdl> ubi part rootfs
icorem6qdl> ubi create rootfs
icorem6qdl> ext4load mmc 0:2 ${loadaddr} ubifs.img
166592512 bytes read in 8091 ms (19.6 MiB/s)
icorem6qdl> ubi write ${loadaddr} rootfs ${filesize}
166592512 bytes written to volume rootfs
icorem6qdl> ubifsmount ubi0:rootfs
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <[email protected]>
Cc: Matteo Lisi <[email protected]>
Cc: Michael Trimarchi <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Modify U-Boot default env settings.
Boot sequence:
1. SD card boot script
2. SD card boot no script
3. SATA boot script
4. SATA boot no script
5. eMMC boot script
6. eMMC boot no script
Signed-off-by: Uri Mashiach <[email protected]>
Acked-by: Igor Grinberg <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
