| Age | Commit message (Collapse) | Author |
|---|
|
Migrate the PXA serial driver to be configured via Kconfig.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
|
|
Remove the custom low-level initialization function and reuse the
default low-level initialization function. But this requires the
ARMV8_MULTIENTRY config option to be enabled for Exynos7420.
On Exynos7420, the boot CPU belongs to the second cluster and so
with ARMV8_MULTIENTRY config option enabled, the 'branch_if_master'
macro fails to detect the CPU as boot CPU. As a temporary workaround
the CPU_RELEASE_ADDR is set to point to '_main'.
Cc: Minkyu Kang <[email protected]>
Cc: Alison Wang <[email protected]>
Signed-off-by: Thomas Abraham <[email protected]>
Reviewed-by: Alison Wang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
The previous partition table did not support a separate device tree
and the kernel size was limited to 4MB. This update shows the
location of the device tree (labeled as spl-os) for those who
want to use Falcon Mode or use U-Boot to store the Flattened
Device Tree (FDT) to NAND without appending it to the kernel.
This also grows the kernel to 6MB since 4MB was becomming tight
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The memory map defined in commit ("49c7303f0e52: OMAP3: Enable SPL
on omap3_logic) was used by a copy-paste of another board without
fully understanding how the map works in Falcon mode. This patch
undoes the customization and uses the default SPL Memory Map
for OMAP3.
When building the uImage, set LOADADDR=0x82000000 and Falcon
mode should properly load.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Remove the need to explicitly add SHA/RSA pairings. Invalid SHA/RSA
pairings will still fail on verify operations when the hash length is
longer than the key length.
Follow the same naming scheme "checksum,crytpo" without explicitly
defining the string.
Indirectly adds support for "sha1,rsa4096" signing/verification.
Signed-off-by: Andrew Duda <[email protected]>
Signed-off-by: aduda <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Cut down on the repetition of algorithm information by defining separate
checksum and crypto structs. image_sig_algos are now simply pairs of
unique checksum and crypto algos.
Signed-off-by: Andrew Duda <[email protected]>
Signed-off-by: aduda <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Padding verification was done against static SHA/RSA pair arrays which
take up a lot of static memory, are mostly 0xff, and cannot be reused
for additional SHA/RSA pairings. The padding can be easily computed
according to PKCS#1v2.1 as:
EM = 0x00 || 0x01 || PS || 0x00 || T
where PS is (emLen - tLen - 3) octets of 0xff and T is DER encoding
of the hash.
Store DER prefix in checksum_algo and create rsa_verify_padding
function to handle verification of a message for any SHA/RSA pairing.
Signed-off-by: Andrew Duda <[email protected]>
Signed-off-by: aduda <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
checksum_algo's pad_len field isn't actually used to store the length of
the padding but the total length of the RSA key (msg_len + pad_len)
Signed-off-by: Andrew Duda <[email protected]>
Signed-off-by: aduda <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
With the move to arch/arm/mach-omap2 there are now very few uses of
CONFIG_OMAP_COMMON and further they can all be replaced with
CONFIG_ARCH_OMAP2, so do so.
Signed-off-by: Tom Rini <[email protected]>
|
|
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories. All refernces to the former locations are updated to
the current locations. For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.
Signed-off-by: Tom Rini <[email protected]>
|
|
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
Make Android partition table the same as for AM57x EVM.
1. Make "bootloader" partition start from 0x300 sectors offset, so
DRA7 is bootable in Android mode (see
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR option).
2. Increase "bootloader" partition size, because size of u-boot.img is
about 632 KiB (when building DT defconfig, with FIT image enabled).
3. Specify "reserved" partition explicitly, rather than specifying
"efs" partition start. Reserved area will be used to store U-Boot
environment on eMMC. It's convenient to have it exposed explicitly
so we can read/write U-Boot environment.
4. Keep all Android partitions locations intact, by reducing
"reserved" partition size. CONFIG_ENV_SIZE is considered.
Signed-off-by: Sam Protsenko <[email protected]>
|
|
Signed-off-by: Sam Protsenko <[email protected]>
|
|
"fastboot oem format" command reuses "gpt write" command, which in turn
requires correct partitions defined in $partitions variable. This patch
adds such definition of Android partitions for DRA7XX EVM board.
By default $partitions variable contains Linux partition table. In order
to prepare Android environment one can run next commands from U-Boot
shell:
=> env set partitions $partitions_android
=> env save
After those operations one can go to fastboot mode and perform
"fastboot oem format" to create Android partition table.
While at it, enable CONFIG_RANDOM_UUID to spare user from providing
UUIDs for each partition manually.
Signed-off-by: Sam Protsenko <[email protected]>
|
|
Add support for distro_bootcmd on MMC and fall back to prior
behavior if distro_bootcmd fails.
Tested on Beagleboad xM to boot GRUB2 (and then Linux kernel) in EFI mode
from MMC.
Signed-off-by: Guillaume GARDET <[email protected]>
Cc: Tom Rini <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
On "fastboot reboot-bootloader" we check "dofastboot" variable and do
"fastboot 0" command in U-Boot if it's 1. But there are boards which have
USB controller number other than 0, so it should be respected when
performing "fastboot" command.
This patch reuses CONFIG_FASTBOOT_USB_DEV option toprovide correct USB
controller number to "fastboot" command.
Signed-off-by: Sam Protsenko <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
LPUART0 is used by default, and it's using platform clock.
Signed-off-by: Shaohui Xie <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
The patch adds support for Freescale ls1021a-iot board.
Signed-off-by: Feng Li <[email protected]>
[YS: rewrite commit message, fix whitespace in Kconfig]
Reviewed-by: York Sun <[email protected]>
|
|
There is the stmicro DSPI flash on LS12080ARDB.
Enable DSPI flash related configure options.
Signed-off-by: Yuan Yao <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add optimization parameters like "quiet" in bootargs to reduce the system
boot time
Signed-off-by: Pratiyush Mohan Srivastava <[email protected]>
Signed-off-by: Harninder Rai <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <[email protected]>
Cc: York Sun <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Mugunthan V N <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
This option isn't used for anything, so get rid of it.
Signed-off-by: Sam Protsenko <[email protected]>
|
|
Signed-off-by: Sam Protsenko <[email protected]>
[trini: Fix sniper and kc1 migration]
Signed-off-by: Tom Rini <[email protected]>
|
|
INFO macro make flash table entries more adjustable like
adding new flash_info attributes, update ID length bytes
and so on and more over it will sync to Linux way of defining
flash_info attributes.
- Add JEDEC_ID
- Add JEDEC_EXT macro
- Add JEDEC_MFR
- spi_flash_params => spi_flash_info
- params => info
Cc: Simon Glass <[email protected]>
Cc: Bin Meng <[email protected]>
Cc: York Sun <[email protected]>
Cc: Vignesh R <[email protected]>
Cc: Mugunthan V N <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: Siva Durga Prasad Paladugu <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Tested-by: Jagan Teki <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
|
|
Patch queue for efi - 2016-11-17
Highlights this time around:
- x86 efi_loader support
- hello world efi test case
- network device name is now representative
- terminal output reports modes correctly
- fix psci reset for ls1043/ls1046
- fix efi_add_runtime_mmio definition for x86
- efi_loader support for ls2080
|
|
Most new systems in U-Boot these days make use of the generic "distro"
framework which allows a user to have U-Boot scan for a bootable OS
on all available media types.
This patch extends the LS2080ARDB board to use that framework if the
hard coded NOR flash location does not contain a bootable image.
Signed-off-by: Alexander Graf <[email protected]>
|
|
The efi_add_runtime_mmio prototype for disabled CONFIG_EFI_LOADER
was different from the enabled one. Sync them.
Signed-off-by: Alexander Graf <[email protected]>
|
|
Signed-off-by: Stefano Babic <[email protected]>
Signed-off-by: Heiko Schocher <[email protected]>
|
|
Correct the sdhci minimum frequency for ep platform.
It should be right shift instead of left shift operand.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The new FW interface returns the IDCODE and version register, leaving
extracting bitfields to the caller.
Cc: Michal Simek <[email protected]>
Cc: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Soren Brinkmann <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Zynq 7000S (Single A9 core) devices is using different ID code.
This patch adds this new codes and assign them.
Signed-off-by: Michal Simek <[email protected]>
|
|
Enable zynq Nand flash controller driver for a zynq ZC770
XM011(dc2) board.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
The topic-miami SoMs contain a Zynq xc7z015 or xc7z030 SoC, 1GB DDR3L RAM,
32MB QSPI NOR flash and 256MB NAND flash.
The topic-miamiplus SoMs contain a Zynq xc7z035, xc7z045 or xc7z100 SoC,
2x 1GB DDR3L RAM, 64MB dual-parallel QSPI flash, clock sources
and a fan controller.
The "Florida" carrier boards add SD, USB, ethernet and other interfaces.
Signed-off-by: Mike Looijmans <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Rather than hard-coding the relocation type, add it to the ELF header file
and use it from there.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
It is useful to have a basic sanity check for EFI loader support. Add a
'bootefi hello' command which loads HelloWord.efi and runs it under U-Boot.
Signed-off-by: Simon Glass <[email protected]>
[agraf: Fix documentation, add unfulfilled kconfig dep]
Signed-off-by: Alexander Graf <[email protected]>
|
|
At present we use a CONFIG option in efi.h to determine whether we are
building the EFI stub or not. This means that the same header cannot be
used for EFI_LOADER support. The CONFIG option will be enabled for the
whole build, even when not building the stub.
Use a different define instead, set up just for the files that make up the
stub.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
When adding network interface node use Messaging device path with
subtype MAC Address and device's MAC address as a value instead
of Media Device path type with subtype File Path and path "Net"
Signed-off-by: Oleksandr Tymoshenko <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
Like [1], reset the FLP burst timing for the KSZ9031 to the 16ms
specified by the IEEE802.3 standard from the chip's default of 8ms.
For more details, see the "Auto-Negotiation Timing" section of the
KSZ9031RNX datasheet.
[1] https://patchwork.kernel.org/patch/6558371/
Signed-off-by: Ash Charles <[email protected]>
Acked-by: Joe Hershberger <[email protected]>
|
|
As the upcoming driver model integration takes up some more precious flash
space first make sure to drop expensive LZMA support.
Signed-off-by: Marcel Ziswiler <[email protected]>
|
|
|
|
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Not all networks have a DHCP server configured properly, so these
scripts make it easier to boot in that scenario.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
The LCD isn't supported in U-Boot and the LCD is now configured in
the device tree, so this code is pointless.
V2: Eliminiate erroneous newline.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Unify the partitions of each chip then it will be more easy for us to
write scripts, tools or guides for rockchip chips.
Those extra partitions mostly are used to be compatible with our
internal loaders (such as miniloader which was same as spl, or
android loader then we can support dual boot)
Signed-off-by: Jacob Chen <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
rk3399 has two mmc dev controller:
mmc 0: SD card;
mmc 1: EMMC
U-Boot will scan the mmc boot device configured by CONFIG_SYS_MMC_ENV_DEV,
since evb has emmc on board, let's set the EMMC as default.
Signed-off-by: Kever Yang <[email protected]>
|
|
I am not sure why this limit is changing. But my kernel
doesn't load when it's above 256. This was testing on the
rock2 board.
Signed-off-by: Sandy Patterson <[email protected]>
Updated commit subject:
Signed-off-by: Simon Glass <[email protected]>
|
|
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: Masahiro Yamada <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <[email protected]>
Cc: Ian Campbell <[email protected]>
Cc: Hans de Goede <[email protected]>
Signed-off-by: Jagan Teki <[email protected]>
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
