| Age | Commit message (Collapse) | Author |
|---|
|
Add the missing CONFIG_BUILD_TARGET to get u-boot-with-spl.sfp built
automatically upon running make in the source tree.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Denis Bakhvalov <[email protected]>
|
|
Don't understand how it happened, but this change got applied twice!
Therefore, removing the duplicated items.
Signed-off-by: Steve Rae <[email protected]>
|
|
transmission and storage
As tested on the Odroid XU3, large files to be stored on the file system
require considerable time to be physically written to the medium.
The default 300 ms is not enough to store large file (e.g. 26 MiB).
To fix this situation the DFU_MANIFEST_POLL_TIMEOUT has been defined.
It is used to cease the communication with dfu-util and allow the target
board to store the data on file system.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <[email protected]>
Reported-by: Alex Gdalevich <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Tested-by: Heiko Schocher <[email protected]>
|
|
Signed-off-by: Zhao Qiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add USB XHCI support for ls1043qds board.
Signed-off-by: Gong Qianyu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Before Linux boot DPL must be deployed to DPAA2 interface.
So update bootcmd env variable to make sure DPL deployment before
Linux boot.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Define mcinitcmd env variable to load Management complex during
u-boot boot sequence.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Increase default hugepage count to 256 from 16
Signed-off-by: Ashish Kumar <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <[email protected]>
[[email protected]: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <[email protected]>
|
|
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <[email protected]>
Tested-by: Siarhei Siamashka <[email protected]>
Acked-by: Siarhei Siamashka <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <[email protected]>
CC: Alison Wang <[email protected]>
CC: Bin Meng <[email protected]>
Reviewed-by: Bin Meng <[email protected]>
Reviewed-by: Alison Wang <[email protected]>
|
|
|
|
Implement a DMA uclass so that the devices like ethernet, spi,
mmc etc can offload the data transfers from/to the device and
memory.
Signed-off-by: Mugunthan V N <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
|
|
Extend options for saving variables to QSPI.
Reviewed-by: Jagan Teki <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Zybo contains on board HDMI that's why enable EDID.
Doing it via config because zynq i2c driver hasn't been moved to DM yet
and enabling via Kconfig requires DM_I2C.
This will be moved that driver is moved to DM.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
This phy is available at Zybo board.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
reg-offset is the part of standard 8250 binding in the kernel.
It is shifting start of address space by reg-offset.
On Xilinx platform this offset is typically 0x1000.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
|
Remove the miss-placed \0 and add missing ; for usbboot env variable.
Signed-off-by: Jason Wu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Use RAM support in jtagboot mode.
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Moritz Fischer <[email protected]>
|
|
Remove CONFIG_ZYNQ_BOOT_FREEBSD configuration option and setup
CONFIG_SYS_MMC_MAX_DEVICE 1 for all Zynq boards.
Signed-off-by: Michal Simek <[email protected]>
|
|
OF_CONTROL is setup by default and memory reading is done via DT. Remove
all config files with memory references.
Signed-off-by: Michal Simek <[email protected]>
|
|
Add Arasan SDHCI entry to Kconfig and fix all references.
Signed-off-by: Michal Simek <[email protected]>
|
|
Clean config file.
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
Introduce macros and command to support booting M4 core for
i.MX7D SabreSD board.
Signed-off-by: Ye.Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Introduce macros and command to support booting M4 core for
i.MX6SX SabreSD board.
Signed-off-by: Ye.Li <[email protected]>
Signed-off-by: Peng Fan <[email protected]>
|
|
Implement board specific functions to select the environment device and
partition when booting from SD/MMC.
SD2: mmc 0 0
SD3: mmc 1 0
eMMC: mmc 2 1
Signed-off-by: Soeren Moch <[email protected]>
|
|
Refactored data structure for CAAM's job ring and Secure Memory
to support i.MX7.
The new memory map use macros to resolve SM's offset by version.
This will solve the versioning issue caused by the new version of
secure memory of i.MX7
Signed-off-by: Ulises Cardenas <[email protected]>
Reviewed-by: Stefano Babic <[email protected]>
|
|
Select CONFIG_FSL_QSPI so that the SPI can be probed:
=> sf probe
SF: Detected N25Q256 with page size 256 Bytes, erase size 64 KiB, total 32 MiB
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
|
|
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.
This adds a simple driver to enable serial port and handle GPIO.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
|
|
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <[email protected]>
Acked-by: Nicolas Ferre <[email protected]>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Andreas Bießmann <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Andreas Bießmann <[email protected]>
|
|
New features for smartweb:
* switch to hush command parser
* change autoboot stop to <ESC><ESC>
* allow to write ethaddr
Signed-off-by: Matthias Michel <[email protected]>
Reviewed-by: Samuel Egli <[email protected]>
Cc: Roger Meier <[email protected]>
Cc: Heiko Schocher <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Andreas Bießmann <[email protected]>
|
|
This allows U-Boot to expose UMS and DFU protocols on this port in device
mode, or to act as a USB host on the port, using an "OTG" (micro-B to
female A host) cable.
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This option is no longer used now that DM_USB is enabled.
Fixes: 534f9d3feffd ("dm: tegra: usb: Move USB to driver model")
Signed-off-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Anatolij Gustschin <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Anatolij Gustschin <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <[email protected]>
Acked-by: Anatolij Gustschin <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
While we transition to using driver model for video, we need to support both
options.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Sync up these files with Linux v4.4.
Signed-off-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
The kernel gets much too sad when the ramdisk is loaded too high into the 1GiB
of memory on Raspberry Pi 2:
## Flattened Device Tree blob at 00000100
Booting using the fdt blob at 0x000100
Loading Ramdisk to 39c14000, end 3ab45067 ... OK
Using Device Tree in place at 00000100, end 000045ea
...
[ 0.599346] Unpacking initramfs...
[ 0.602924] Unable to handle kernel paging request at virtual address f9c14000
Placement of the device tree was fixed in 89ca1000 (ARM: rpi: set fdt_high
in the default environment).
Signed-off-by: Lubomir Rintel <[email protected]>
Acked-by: Stephen Warren <[email protected]>
|
|
With the recent addition of UBI support, this patch will add the preset
parameters to allow for mouting an UBIFS from the 'fs' partition in NAND.
-V2: ubi.mtd=fs instead of ubi.mtd=4
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
