| Age | Commit message (Collapse) | Author |
|---|
|
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Tested on the following baseline (note "dirty" since I enabled
ALT_BOOT in the config in order to use the alternate boot bank.)
Everything seems to work fine with no additional changes. The
banner warning message is now gone.
---
U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)
CPU: 8548E, Version: 2.1, (0x80390021)
Core: e500, Version: 2.2, (0x80210022)
Clock Configuration:
CPU0:990 MHz,
CCB:396 MHz,
DDR:198 MHz (396 MT/s data rate), LBC:99 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
I2C: ready
DRAM: Detected UDIMM
SDRAM: 128 MiB
256 MiB (DDR2, 64-bit, CL=3, ECC off)
Flash: 72 MiB
L2: 512 KiB enabled
*** Warning - bad CRC, using default environment
PCI: Host, 64 bit, 66 MHz, sync, arbiter
00:01.0 - 8086:1026 - Network controller
PCI1: Bus 00 - 00
PCIe1: Root Complex, x1 gen1, regs @ 0xe000a000
02:00.0 - 1148:9e00 - Network controller
PCIe1: Bus 01 - 02
In: serial
Out: serial
Err: serial
Net: eTSEC0 [PRIME], eTSEC1
Hit any key to stop autoboot: 0
=> ver
U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)
powerpc-linux-gcc (GCC) 4.5.2
GNU ld (GNU Binutils) 2.21
=>
---
Signed-off-by: Paul Gortmaker <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.
Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.
Signed-off-by: Valentin Longchamp <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
|
|
Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.
Signed-off-by: Soeren Moch <[email protected]>
|
|
|
|
add the spl info in the header file.
Also, added a macro statement in m6sabre_common.h to avoid compiler
warning.
Signed-off-by: John Tobias <[email protected]>
|
|
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space
for u-boot image.
When enabling NAND flash support feature, the u-boot image size has exceeded the
384KB, which causes overlay to the environment variables storage.
Signed-off-by: Ye.Li <[email protected]>
Acked-by: Fabio Estevam <[email protected]>
|
|
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Otavio Salvador <[email protected]>
|
|
U-Boot 2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: WDOG
Board: ot1200
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
In: serial
Out: serial
Err: serial
Net: using phy at 0
FEC [PRIME]
Hit any key to stop autoboot: 0
=> usb start
(Re)start USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
|
+-3 Mass Storage (480 Mb/s, 80mA)
| USBest Technology USB Mass Storage Device 0000000000028B
|
+-4 Vendor specific (480 Mb/s, 2mA)
=>
Signed-off-by: Christian Gmeiner <[email protected]>
|
|
|
|
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
Acked-by: Marek Vasut <[email protected]>
|
|
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).
Also add some extra clock register constant defines.
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
|
|
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Acked-by: Ian Campbell <[email protected]>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
|
|
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Move CONFIG_DEFAULT_DEVICE_TREE from board config
directly to defconfig.
This patch removes compilation warning:
include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE"
redefined [enabled by default]
#define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
This commit moves CONFIG_SH2, CONFIG_SH2A, CONFIG_SH3, CONFIG_SH4
to Kconfig renaming into CONFIG_CPU_SH2, CONFIG_CPU_SH2A,
CONFIG_CPU_SH3, CONFIG_CPU_SH4, respectively because
arch/sh/Kconfig of Linux uses CONFIG_CPU_SH* convention.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <[email protected]>
Cc: Anatolij Gustschin <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Cc: York Sun <[email protected]>
Signed-off-by: Nikita Kiryanov <[email protected]>
|
|
This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.
Signed-off-by: Valentin Longchamp <[email protected]>
|
|
|
|
|
|
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.
With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack. In some use cases, the system hangs up
with stack over-flow.
Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
FAT-formated USB storage device access is available.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
This patch adds config support needed for ZYBO target and has
been tested on Rev. B ZYBO hardware.
Signed-off-by: Tinghui Wang <[email protected]>
[PC changes:
* Dropped boards.cfg change (rebase conflict)
* Dropped custom u-boot env
* Added DTS
* Misc forward-porting changes
]
Signed-off-by: Peter Crosthwiate <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
|
|
|
|
Change clock of SCIF for Alt board is used to external clock.
This changes to using external clock.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Sonic Zhang <[email protected]>
|
|
R-Car SoCs of rmobile have same IP of rcar-i2c, and have same address.
This moves rcar-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
R-Car SoCs of rmobile have same IP of sh-i2c, and have same address.
This moves sh-i2c of the address defined to rcar-base.h as common header of
R-Car SoCs, and headers of each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Alt board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Lager board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Koelsch board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Gose board has two USB ports, and can use USB EHCI HCD driver of rmobile.
This adds driver settings in order to use this driver.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Gose board has one ether port, this works using sh-ether driver.
This adds GPIO settings and driver settings in order to use the sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
The gose board has R8A7793, 1GB DDR3-SDRAM, USB, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
- QSPI
- SPI
Signed-off-by: Hisashi Nakamura <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
CC: Masahiro Yamada <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Anatolij Gustschin <[email protected]>
|
|
|
|
The header file include/usb.h references ARCH_DMA_MINALIGH and
block_dev_desc_t, thus it must include <asm/cache.h> and <part.h>.
Signed-off-by: Masahiro Yamada <[email protected]>
|
|
Add example of an USB UDC configuration with DFU and UMS.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Vince Bridgers <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Cc: Stefan Roese <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
|
|
Allow passing in a custom configuration of the gusbcfg register
via platform data.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Vince Bridgers <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Cc: Stefan Roese <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
|
|
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Vince Bridgers <[email protected]>
Acked-by: Pavel Machek <[email protected]>
Cc: Stefan Roese <[email protected]>
Reviewed-by: Lukasz Majewski <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
|
|
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Marek Vasut <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Vince Bridgers <[email protected]>
Cc: Albert Aribaud <[email protected]>
Cc: Pavel Machek <[email protected]>
Cc: Simon Glass <[email protected]>
|
|
With fresh environment the kernel gets wrong console
argument and boots without console output. Fix it.
Reported-by: Dinh Nguyen <[email protected]>
Signed-off-by: Anatolij Gustschin <[email protected]>
Cc: Chin Liang See <[email protected]>
Cc: Dinh Nguyen <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
Add support for splash screen on both DVI and SCF0403 LCD.
Signed-off-by: Igor Grinberg <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
|
