| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for lager.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for koelsch.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Add CONFIG_SYS_GENERIC_BOARD to use common/board_*.c for armadillo800eva.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Lager board has USB ports. This add support of USB controller of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Koelsch board has USB ports. This add support of USB controller of rmobile.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Because do not need these feature to lager board, this delete it.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
The define of SCIF register was already defined in rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Because do not need these feature to koelsch board, this delete it.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
The define of SCIF register was already defined in rcar-base.h.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Added support to load a bitstream image in chunks by reading it in
chunks from SD/MMC.
Command format:
loadfs [dev] [address] [image size] [blocksize] <interface>
[<dev[:part]>] <filename>
Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Use new fpga commands for loading partial bitstreams.
Signed-off-by: Michal Simek <[email protected]>
|
|
Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <[email protected]>
|
|
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
Fix typo in CMD_FPGA command enabling.
Signed-off-by: Michal Simek <[email protected]>
|
|
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
|
|
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.
The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.
Signed-off-by: Liu Gang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.
Signed-off-by: Kim Phillips <[email protected]>
Acked-by: Edward Swarthout <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.
Signed-off-by: Aneesh Bansal <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <[email protected]>
Signed-off-by: Ramneek Mehresh <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.
Signed-off-by: Chunhe Lan <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Conflicts:
boards.cfg
Trivial conflict, maintainer change plus board addition
|
|
|
|
|
|
Signed-off-by: Jaehoon Chung <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Support the DDR mode at dw-mmc controller
Signed-off-by: Jaehoon Chung <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Jaehoon Chung <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Jaehoon Chung <[email protected]>
Reviewed-by: Lukasz Majeski <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <[email protected]>
Tested-by: Lukasz Majewski <[email protected]>
Acked-by: Lukasz Majewski <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Exynos serise can be supported the dw-mmc controller.
So, it's good that used the general prefix as "_EXYNOS_DWMMC".
Signed-off-by: Jaehoon Chung <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
UMS-related defines were added to Samsung Goni config header.
Signed-off-by: Mateusz Zalega <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Mateusz Zalega <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Proper adjustment for supporting DFU at GONI target has been made.
The s5p_goni.h file has been updated. Moreover the code for low level
USB initialization has been added to GONI board code.
The malloc pool has been enlarged in order to support larger buffer
sizes needed by DFU implementation.
Signed-off-by: Arkadiusz Wlodarczyk <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Signed-off-by: Mateusz Zalega <[email protected]>
Tested-by: Arkadiusz Wlodarczyk <[email protected]>
Tested-by: Mateusz Zalega <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Configuration file for GONI has been updated to support FAT file system,
new mmc partitioning scheme and read linux kernel from eMMC instead of
OneNAND.
Signed-off-by: Arkadiusz Wlodarczyk <[email protected]>
Signed-off-by: Kyungmin Park <[email protected]>
Signed-off-by: Mateusz Zalega <[email protected]>
Tested-by: Arkadiusz Wlodarczyk <[email protected]>
Tested-by: Mateusz Zalega <[email protected]>
Signed-off-by: Minkyu Kang <[email protected]>
|
|
|
|
|
|
SPL should load "u-boot-dtb.img" if both CONFIG_OF_CONTROL
and CONFIG_OF_SEPARATE are defined.
Otherwise, "u-boot.img" should be loaded.
Since CONFIG_OF_CONTROL is always undefined for SPL_BUILD,
the undef block should be moved below the conditional definition
of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <[email protected]>
Cc: Michal Simek <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
|
|
|
