| Age | Commit message (Collapse) | Author |
|---|
|
Adapt highbank to use config_distro_defaults.h and remove the redundant
defines.
Signed-off-by: Rob Herring <[email protected]>
|
|
|
|
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.
Signed-off-by: York Sun <[email protected]>
CC: Troy Kisky <[email protected]>
|
|
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Reviewed-by: Jagannadha Sutradharudu Teki <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Eric Nelson <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <[email protected]>
|
|
MACH_TYPE_LAGER and CONFIG_MACH_TYPE are not already available on Lager board.
This removes them.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
CONFIG_SH_TMU_CLK_FREQ of lager is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
CONFIG_SH_TMU_CLK_FREQ of koelsch is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
Signed-off-by: Nobuhiro Iwamatsu <[email protected]>
|
|
|
|
|
|
|
|
Signed-off-by: Alexey Brodkin <[email protected]>
|
|
With 32 milliseconds delay on some boards EEMPROM got written inconsistently.
With 64 msec all of our existig boards show properly written EEPROM.
Cc: Tom Rini <[email protected]>
Signed-off-by: Alexey Brodkin <[email protected]>
|
|
add support for the ids8313 board.
CPU: e300c3, MPC8313, Rev: 2.1 at 396 MHz, CSB: 132 MHz
I2C: ready
SPI: ready
DRAM: 128 MiB (DDR2, 32-bit, ECC off, 264 MHz)
Flash: 8 MiB
NAND: 128 MiB
Net: TSEC0, TSEC1 [PRIME]
public key on NOR flash start
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
|
|
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <[email protected]>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <[email protected]>
|
|
Adds support for clock sourcing from sysclk(100MHz) for usb
on T104xRDB and T1040QDS. This requires changing reference divisor
and multiplication factor to derive usb clock from sysclk.
Signed-off-by: Nikhil Badola <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1040 and it's variants provide "Single Oscillator Source" Reference Clock Mode.
In this mode, single onboard oscillator(DIFF_SYSCLK) can provide the reference clock
(100MHz) to the following PLLs:
• Platform PLL
• Core PLLs
• USB PLL
• DDR PLL, etc
The cfg_eng_use0 of porsr1 register identifies whether the SYSCLK (single-ended) or
DIFF_SYSCLK (differential) is selected as the clock input to the chip.
get_sys_info has been enhanced to add the diff_sysclk so that the
various drivers can be made aware of ths diff sysclk configuration and
act accordingly.
Other changes:
-single_src to ddr_refclk_sel, as it is use for checking ddr reference clock
-Removed the print of single_src from get_sys_info as this will be
-printed whenever somebody calls get_sys_info which is not appropriate.
-Add print of single_src in checkcpu as it is called only once during initialization
Signed-off-by: Poonam Aggrwal <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
Signed-off-by: Vijay Rai <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.
Signed-off-by: Haijun Zhang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
U-boot binary size has been increased from 512KB to 768KB.
So update CONFIG_SYS_MONITOR_LEN to reflect the same.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add support of loading image, binary for MMC and SPI during SPL boot.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1042RDB_PI board does not have QE connector.
So disable CONFIG_QE and CONFIG_U_QE for T1042RDB_PI
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add u-qe support for t1040qds
Signed-off-by: Zhao Qiang <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add deep sleep support on T104xRDB platforms.
Signed-off-by: Tang Yuantian <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Add deep sleep support on T1040QDS platform.
Signed-off-by: Tang Yuantian <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
When T104x soc wakes up from deep sleep, control is passed to the
primary core that starts executing uboot. After re-initialized some
IP blocks, like DDRC, kernel will take responsibility to continue
to restore environment it leaves before.
Signed-off-by: Tang Yuantian <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
Increase TXFIFOTHRES field value in TXFILLTUNING register of usb for T4 Rev 2.0.
This decreases data burst rate with which data packets are posted from the TX
latency FIFO to compensate for latencies in DDR pipeline during DMA.
This avoids Tx buffer underruns and leads to successful usb writes
Signed-off-by: Ramneek Mehresh <[email protected]>
Signed-off-by: Nikhil Badola <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.
This support of CPLD includes
- files and register defintion
- Commands to swtich alternate bank and default bank
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.
Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file
Signed-off-by: Vijay Rai <[email protected]>
Signed-off-by: Priyanka Jain <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
NOR flash is on CS1 instead of CS2 when NAND boot.
So correct NOR chip selection to CS1 from CS2.
Signed-off-by: Shengzhou Liu <[email protected]>
Reviewed-by: York Sun <[email protected]>
|
|
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.
Signed-off-by: York Sun <[email protected]>
|
|
Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register
calculation and programming.
Signed-off-by: York Sun <[email protected]>
|
