| Age | Commit message (Collapse) | Author |
|---|
|
add gmac support for sama5d3xek board, the gmac embedded in:
- sama5d33, sama5d34, sama5d35
Signed-off-by: Bo Shen <[email protected]>
Signed-off-by: Andreas Bießmann <[email protected]>
|
|
|
|
The target uses AUART 3 instead of the DUART for console output.
Signed-off-by: Andreas Wass <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: Marek Vasut <[email protected]>
|
|
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
Enable p1022ds to start from eSPI with SPL.
Signed-off-by: Ying Zhang <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
Enable p1022ds to start from eSDHC with SPL.
Signed-off-by: Ying Zhang <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
functionality for common SPL
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.
Signed-off-by: Ying Zhang <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
This patch removes support for the APM 405CR CPU.
This CPU is EOL and no board uses this chip.
Signed-off-by: Matthias Fuchs <[email protected]>
|
|
This board and especially the CPU (PPC405CR) is EOL.
Signed-off-by: Matthias Fuchs <[email protected]>
Acked-by: Wolfgang Denk <[email protected]>
|
|
I2C framework
New I2C framework, introduced after v2013.07 final release, imposed I2C
code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210.
Those boards were using schematic based I2C enumeration (I2C_5, I2C_9).
However, new I2C framework imposes usage of logical I2C adapters numbering
(e.g. I2C_0, I2C_1, etc).
Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions.
Trats board gained definition of second soft I2C adapter.
Signed-off-by: Lukasz Majewski <[email protected]>
Cc: Minkyu Kang <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
enabled
The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.
This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:
SHA1: 385c9ef5a7215b2b0c22836fee6c692dfc8559d7
i2c: add i2c_core and prepare for new multibus support
Signed-off-by: Lukasz Majewski <[email protected]>
Cc: Heiko Schocher <[email protected]>
|
|
This way, we don't have to run mkimage on them.
Signed-off-by: Stephen Warren <[email protected]>
Acked-by: Simon Glass <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Disabling the data cache is no longer required to boot Dalmore, so
enable it. This results in notably better performance when loading
and booting the Linux kernel.
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.
Signed-off-by: Thierry Reding <[email protected]>
Tested-by: Stephen Warren <[email protected]>
Reviewed-by: Stephen Warren <[email protected]>
Signed-off-by: Tom Warren <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <[email protected]>
|
|
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <[email protected]>
Cc: Stefan Roese <[email protected]>
Signed-off-by: Wolfgang Denk <[email protected]>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Wolfgang Denk <[email protected]>
|
|
The __* keywords are reserved. On FreeBSD __unused evaluates
to the attribute unused, causing a compilation failure.
Just use unused instead.
Signed-off-by: Jeroen Hofstee <[email protected]>
cc: [email protected]
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Dirk Eibach <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <[email protected]>
|
|
|
|
Signed-off-by: Antoine Tenart <[email protected]>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: Tom Rini <[email protected]>
|
|
add the am1808 based ipam390 board from Barix.
- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM
interface
- 128MByte, NAND Flash, 8bit databus to the NANDFlash
Interface
- Ethernet PHY Micrel KSZ8051R via RMII
- Console on UART 0
- booting fron nand flash
- spl falcon bootmode
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name()
show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress()
if CONFIG_BOOTSTAGE is not defined.
Signed-off-by: Heiko Schocher <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Albert Aribaud <[email protected]>
Acked-by: Simon Glass <[email protected]>
|
|
Add the generic "poke a GPIO" command, with the GPIO related defines.
Acked-by: Dan Murphy <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Add the generic "poke the SPI bus" command, with the SPI related
defines.
Acked-by: Dan Murphy <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <[email protected]>
|
|
We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms. We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Signed-off-by: Tom Rini <[email protected]>
|
|
Bring in the 'boot_fdt' environment variable that i.MX boards use to try
and load a device tree when booting.
Signed-off-by: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1
in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.
Signed-off-by: Tom Rini <[email protected]>
|
|
Acked-by: Dan Murphy <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
IGEP boards now have Device Tree support in the mainline
kernel. To boot an IGEP board using a DT, a uEnv.txt plain
text file could be used to define a custom uenvcmd that will
be run by the default boot command.
It is more convenient to change the default boot command to
allow loading a FDT if it is stored in the boot dir of the
rootfs uSD/MMC partition.
If no FDT is found then the defaul command tries to boot a
zImage without a DT using legacy boot.
Signed-off-by: Javier Martinez Canillas <[email protected]>
|
|
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and
later of the Linux Kernel, uImage isn't builtable anymore by default, so we
should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
|
|
As config was originally based on am335x_evm.h we have also some
duplicate / unnused #defines.
Commit 15191c91 removed these #defines on various AM335x boards but not
for IGEP COM AQUILA. This patch simply removes them for this board.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
|
|
Add to the default environment the possibily to boot from NAND using
a ubi rootfs. Also the partition scheme is set as follows:
Start Size
SPL : 0x00000000 0x00080000 (512KiB)
U-Boot : 0x00080000 0x00100000 (1MiB)
U-Boot Env : 0x00180000 0x00020000 (128KiB)
File System : 0x001C0000 -
The ubiboot script gets the kernel and the dtb file from the boot directory
of the File System.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
|
|
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As
old kernel is deprecated we should adapt the boot commands to use DTB files.
Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore
by default, so we should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
|
|
After commit:
79cd2f814b1c75efd47161ac27f4cbebf768240f config_cmd_default.h: Remove CONFIG_CMD_MEMTEST
It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from
configuration file.
Signed-off-by: Enric Balletbo i Serra <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
|
|
Add config file
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <[email protected]>
|
|
|
|
Replace license header with SPDX license identifier.
Replace GPL-2.0 with GPL-2.0+.
Signed-off-by: York Sun <[email protected]>
Acked-by: Ramneek Mehresh <[email protected]>
|
|
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <[email protected]>
Acked-by: York Sun <[email protected]>
|
|
|
|
|
