| Age | Commit message (Collapse) | Author |
|---|
|
Opps, after a long time I tested recent u-boot on our
APC405 board. This simple fix makes networking work again.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Albert Aribaud <[email protected]>
Acked-by: Prafulla Wadaskar<[email protected]>
Acked-by: Heiko Schocher<[email protected]>
|
|
These are not used on this board, which uses soft I2C instead.
Signed-off-by: Albert Aribaud <[email protected]>
Acked-by: Prafulla Wadaskar<[email protected]>
Acked-by: Heiko Schocher<[email protected]>
|
|
Use the same configuration around S5P SoCs.
(s5pc100, s5pc110, s5pc210 and so on)
Signed-off-by: Minkyu Kang <[email protected]>
|
|
Signed-off-by: Eric Bénard <[email protected]>
Signed-off-by: Reinhard Meyer <[email protected]>
|
|
convert the board to the new soc architecture
update default config
i2c upgrade taken from eb_cpux9k2.h & board/BuS/eb_cpux9k2/cpux9k2.c
Signed-off-by: Eric Bénard <[email protected]>
Signed-off-by: Reinhard Meyer <[email protected]>
|
|
There was an redesign, so USB is available now.
Signed-off-by: Daniel Gorsulowski <[email protected]>
Signed-off-by: Reinhard Meyer <[email protected]>
|
|
* convert meesc board to use c stucture SoC access
* change gpio access to at91_gpio syntax
* moved CONFIG_SYS_HZ below board and cpu defines (purely cosmetic)
Signed-off-by: Daniel Gorsulowski <[email protected]>
Signed-off-by: Reinhard Meyer <[email protected]>
|
|
Autodetection is undesired now
Signed-off-by: Daniel Gorsulowski <[email protected]>
Signed-off-by: Reinhard Meyer <[email protected]>
|
|
We get two build errors:
fsl_elbc_nand.c: In function 'fsl_elbc_run_command':
fsl_elbc_nand.c:231: error: 'fsl_lbc_t' has no member named 'lsor'
make[1]: *** [/work/wd/tmp-ppc/drivers/mtd/nand/fsl_elbc_nand.o] Error 1
and
ve8313.c: In function 'initdram':
ve8313.c:104: error: expected '=', ',', ';', 'asm' or '__attribute__'
before '*' token
ve8313.c:104: error: 'lbc' undeclared (first use in this function)
ve8313.c:104: error: (Each undeclared identifier is reported only once
ve8313.c:104: error: for each function it appears in.)
ve8313.c:104: error: 'immap_t' has no member named 'lbus'
make[1]: *** [ve8313.o] Error 1
make: *** [board/ve8313/libve8313.a] Error 2
Due to changes to unifiy local bus struct definitions.
Reported-by: Wolfgang Denk <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
The board specific parameters associated with quad rank dimms where
missing. This fixes it so the board will function if quad rank dimms
are placed in it.
Signed-off-by: York Sun <[email protected]>
Signed-off-by: Kumar Gala <[email protected]>
|
|
|
|
|
|
|
|
Enabling USB HOST in defconfig.
Signed-off-by: Ajay Kumar Gupta <[email protected]>
|
|
Tested MSC Host on AM3517EVM.
Signed-off-by: Ajay Kumar Gupta <[email protected]>
|
|
Recent features enabled by default require a larger monitor size for the
cm-bf548 port, so bump it up a bit.
Signed-off-by: Mike Frysinger <[email protected]>
|
|
This patch adds support for the jadecpu board using the
MB86R01 'Jade' SoC from Fujitsu.
Signed-off-by: Matthias Weisser <[email protected]>
|
|
Signed-off-by: Matthias Weisser <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
Commit 6e37b1a3a25004d3df5867de49fff6b3fc9c4f04 modifies several net calls
to take a (const char *) parameter instead of (char *), but in some cases
the modified functions call other functions taking (char *). The end result
is warnings about discarding the const qualifier.
This patch fixes these other function signatures.
Signed-off-by: Ben Warren <[email protected]>
|
|
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <[email protected]>
Acked-by: Dave Liu <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
since commit 1384f3bb8a4f9066805b70c1418eda78ecb73fdd ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Ben Warren <[email protected]>
|
|
This patch has the following fixes/changes:
- Set 'kernel_addr' and 'ramdisk_addr' to correct values and add
'fdt_addr' environment variable
- Remove 'kozio' environment variable
- Remove environmant variables to boot ancient arch/ppc Linux kernels
- Remove CONFIG_SYS_BOOTMAPSZ definition. It's already defined to
the same value in amcc-common.h
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size and default environment
after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Update image size after addition of new environment handling.
Signed-off-by: Matthias Fuchs <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
None of the AMCC boards uses an embedded environment, so there is no
need to run "saveenv" after updating U-Boot. Drop the redundant
commands from the default environment.
Signed-off-by: Wolfgang Denk <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Signed-off-by: Marek Vasut <[email protected]>
|
|
Signed-off-by: Heiko Schocher <[email protected]>
|
|
- nfs-options removed
- hda->sda changed
- mtd parts added
- loadaddress changed
- cmd-line length increased
- lcd stuff removed
- code cleanup (use I/O accessors etc.)
Signed-off-by: Klaus Heydeck <[email protected]>
|
|
This patch enables mvsata driver and related filesystem support.
The patch is tested for ide reset and ext2ls operation for a disk drive connected on SATA port0.
This patch depends upon the patche-series http://lists.denx.de/pipermail/u-boot/2010-August/074908.html
Signed-off-by: Prafulla Wadaskar <[email protected]>
|
|
Add mvsata_ide and cmd_ide configuration in edminiv2 config
Signed-off-by: Albert Aribaud <[email protected]>
|
|
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <[email protected]>
|
|
|
|
Specify vram on command line, remove erroneous call to nandboot
in the boot script, add CONFIG_BOOTDELAY
Signed-off-by: Steve Sakoman <[email protected]>
Acked-by: Nishanth Menon <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
This patch add the basic infrastructure for the TWL6030 driver and enables
support in the two existing OMAP4 boards, Panda and OMAP4430 SDP
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
The OMAP4 x-load code sets gptimer1 clock source to 32Khz. This isn't
acceptable for udelay. This patch changes from gptimer1 to gptimer2,
which uses sys_clk at 38.4 Mhz.
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <[email protected]>
Signed-off-by: Aneesh V <[email protected]>
Signed-off-by: Sandeep Paulraj <[email protected]>
|
|
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function. This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).
Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.
To avoid confusion, rename into getenv_f() [as "running from flash"]
Signed-off-by: Wolfgang Denk <[email protected]>
Acked-by: Detlev Zundel <[email protected]>
|
|
|
|
|
