| Age | Commit message (Collapse) | Author |
|---|
|
This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.
The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.
Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.
The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.
The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.
Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef5340c ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.
The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.
The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.
Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.
Signed-off-by: Alper Nebi Yasak <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Tested-by: Simon Glass <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
|
|
- Rockchip, i.MX and xenon_sdhci updates
|
|
- k210 updates
|
|
Delegate setting the Enhanced Strobe configuration to individual drivers
if they set a function for it. Return -ENOTSUPP if they do not, like
what the MMC uclass does.
Signed-off-by: Alper Nebi Yasak <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
After commit f132aab40327 ("Revert "mmc: fsl_esdhc_imx: use
VENDORSPEC_FRC_SDCLK_ON to control card clock output""), it
involve issue in mmc_switch_voltage(), because of the special
design of usdhc.
For FSL_USDHC, it do not implement VENDORSPEC_CKEN/PEREN/HCKEN/IPGEN,
these are reserved bits(Though RM contain the definition of these bits,
but actually internal IC logic do not implement, already confirm with
IC team). Instead, use VENDORSPEC_FRC_SDCLK_ON to gate on/off the card
clock output. Here is the definition of this bit in RM:
[8] FRC_SDCLK_ON
Force CLK output active
Do not set this bit to 1 unless it is necessary. Also, make sure that
this bit is cleared when uSDHC’s clock is about to be changed (frequency
change, clock source change, or delay chain tuning).
0b - CLK active or inactive is fully controlled by the hardware.
1b - Force CLK active
In default, the FRC_SDCLK_ON is 0. This means, when there is no command
or data transfer on bus, hardware will gate off the card clock. But in
some case, we need the card clock keep on. Take IO voltage 1.8v switch
as example, after IO voltage change to 1.8v, spec require gate off the
card clock for 5ms, and gate on the clock back, once detect the card
clock on, then the card will draw the dat0 to high immediately. If there
is not clock gate off/on behavior, some card will keep the dat0 to low
level. This is the reason we fail in mmc_switch_voltage().
To fix this issue, and concern that this is only the fsl usdhc hardware
design limitation, set the bit FRC_SDCLK_ON in the beginning of the
wait_dat0() and clear it in the end. To make sure the 1.8v IO voltage
switch process align with SD specification.
For standard tuning process, usdhc specification also require the card
clock keep on, so also add these behavior in fsl_esdhc_execute_tuning().
Reviewed-by: Marek Vasut <[email protected]>
Tested-by: Fabio Estevam <[email protected]>
Signed-off-by: Haibo Chen <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
|
|
Update the LZ4 compression module based on LZ4 v1.8.3 in order to
use the newest LZ4_decompress_safe_partial() which can now decode
exactly the nb of bytes requested.
Signed-off-by: Huang Jianan <[email protected]>
|
|
This patch mainly deals with uncompressed files.
Signed-off-by: Huang Jianan <[email protected]>
|
|
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <[email protected]>
Signed-off-by: Niklas Cassel <[email protected]>
Reviewed-by: Leo Yu-Chi Liang <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-video
- fix display of the u-boot logo on Apple devices
- convert Nokia RX-51 to CONFIG_DM_VIDEO
|
|
Prepare v2022.04-rc4
|
|
Add pinctrl driver for Xilinx ZynqMP SOC. This driver is compatible with
linux device tree parameters for configuring pinmux and pinconf.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/2d7eefa83c8c0129f7243a25de56a289e948f6c6.1645626183.git.michal.simek@xilinx.com
|
|
Xilinx ZynqMP SOC can set 6 parameters for its pins. pinmux status
command will print the status of these parameters for each pin. But
current print buffer length is only 40 characters long, increase it
to 80 to print all the parameters.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/3a6be84c8354f38754a9838670cc0319e84f29e8.1645626183.git.michal.simek@xilinx.com
|
|
InstallProtocolInterface() is called with a pointer to the protocol GUID.
There is not guarantee that the memory used by the caller for the protocol
GUID stays allocated. To play it safe the GUID should be copied to U-Boot's
internal structures.
Reported-by: Joerie de Gram <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <[email protected]>
|
|
PHY init
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 5980925e2a5a ("include: configs: j721e_evm: Add support to boot ethfw core in j721e")
Reported-by: Suman Anna <[email protected]>
Signed-off-by: Aswath Govindraju <[email protected]>
|
|
Add a command to show the available events.
Signed-off-by: Simon Glass <[email protected]>
|
|
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <[email protected]>
|
|
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <[email protected]>
|
|
Generate events when devices are probed or removed, allowing hooks
to be added for these situations.
This is controlled by the DM_EVENT config option.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
A 'test' event is the only option for now.
Signed-off-by: Simon Glass <[email protected]>
|
|
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <[email protected]>
|
|
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
|
|
Remove static return type for phy_device_create() to avoid file scope for
this function. Also add required prototype in phy.h.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/1517f4053403fbd53e899d500e7485d068a4f0b6.1645627539.git.michal.simek@xilinx.com
|
|
Add new function to get ethernet phy id from compatible property
of the mdio phy node.
Signed-off-by: Michal Simek <[email protected]>
Signed-off-by: T Karthik Reddy <[email protected]>
Link: https://lore.kernel.org/r/16019efb3820a50330935fdaae191cec1f101b5c.1645627539.git.michal.simek@xilinx.com
|
|
Most of the frequencies are not rounded up to a proper number.
When we need to devide these frequencies to get a number for example
frequency in Mhz, we see it as one less than the actual intended value.
Ex: If we want to get Mhz from frequency 199999994hz, we will calculate
it using div64_u64(199999994, 1000000) and we will get 199Mhz in place
of 200Mhz.
Add a macro DIV64_U64_ROUND_UP for rounding up div64_u64. This is taken
from linux 'commit 68600f623d69("mm: don't miss the last page because of
round-off error")'.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f9fdcba76cd692ae436b1d7883b490e3dc207231.1645626962.git.michal.simek@xilinx.com
|
|
Add firmware API's to set SD configuration and to check if a purticular
function is supported.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/f64fa2f73e4775e9ad2f4d91339d6c74b43116a3.1645626962.git.michal.simek@xilinx.com
|
|
Update enum pm_ioctl_id with more IOCTLs.
Add enum pm_sd_config_type to support dynamic sd configuration.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/9aba090ec11d2591dbe6978e73e64384873c99fc.1645626962.git.michal.simek@xilinx.com
|
|
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <[email protected]>
|
|
Based on discussion at
https://lore.kernel.org/r/[email protected] we got
recommendation to use explicit values for all enums.
So, add explicit values to all pinctrl related enums for readability.
Signed-off-by: Ashok Reddy Soma <[email protected]>
Signed-off-by: Michal Simek <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Link: https://lore.kernel.org/r/dcdb20e7252ea7465e9f984d815e9624c30e9558.1645624969.git.michal.simek@xilinx.com
|
|
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).
## Loading kernel from FIT Image at 90000000 ...
Could not find configuration node
ERROR: can't get kernel image!
Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].
The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].
The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.
When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.
[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473e4fe018aececc8ed3bf8fc2b3ff561
Signed-off-by: Romain Naour <[email protected]>
Cc: Tom Rini <[email protected]>
Reviewed-by: Denys Dmytriyenko <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CHIP_SELECTS_PER_CTRL
Cc: Alison Wang <[email protected]>
Cc: Pramod Kumar <[email protected]>
Cc: Priyanka Jain <[email protected]>
Cc: Rajesh Bhagat <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOOTP_MAY_FAIL
CONFIG_BOOTP_VENDOREX
CONFIG_BOOTP_BOOTFILESIZE
CONFIG_BOOTP_NISDOMAIN
CONFIG_BOOTP_TIMEOFFSET
Cc: Ramon Fried <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This slight environment modification shouldn't be in the CONFIG
namespace, change it.
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOOTFILE
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_POSTCLK_INIT
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_ECC_SUPPORT
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BIOSEMU
Cc: Simon Glass <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BOARD_COMMON
Signed-off-by: Tom Rini <[email protected]>
|
|
These particular values are not configurable and today we always set
CONFIG_SECURE_BL1_ONLY. Move these to where they're used in the code,
and drop from the CONFIG namespace.
Cc: Minkyu Kang <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Jaehoon Chung <[email protected]>
Reviewed-by: Minkyu Kang <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_BTB
Signed-off-by: Tom Rini <[email protected]>
|
|
Remove some code, primarily CPM2 related, that is now unused since the
removal of MPC8540/60ADS.
Fixes 3913191c8a6b ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS")
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Update and fixes for sl28, lx2, pblimage generation for some powerpc
products
|
|
Implements SCMI APIs to retrieve the number exposed SCMI clocks using
SCMI_PROTOCOL_ATTRIBUTES messages and the names of the clocks using
SCMI_CLOCK_ATTRIBUTES messages.
This change updates sandbox SCMI clock test driver to manage these
2 new message IDs.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Clement Leger <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Gabriel Fernandez <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Changes devm_scmi_process_msg() first argument from target parent device
to current SCMI device and lookup the SCMI agent device among SCMI device
parents for find the SCMI agent operator needed for communication with
the firmware.
This change is needed in order to support CCF in clk_scmi driver unless
what CCF will fail to find the right udevice related to exposed SCMI
clocks.
This patch allows to simplify the caller sequence, using SCMI device
reference as parameter instead of knowing SCMI uclass topology. This
change also adds some protection in case devm_scmi_process_msg() API
function is called for an invalid device type.
Cc: Lukasz Majewski <[email protected]>
Cc: Sean Anderson <[email protected]>
Cc: Jaehoon Chung <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
Signed-off-by: Etienne Carriere <[email protected]>
|
|
Support for Apple M1 Pro and Max will allow using a single binary for
all M1 SoCs. The M1 Pro/Max have a different memory layout. The RAM
start address is 0x100_0000_0000 instead of 0x8_0000_0000.
Replace the hardcoded memory layout with dynamic initialized
environment variables in board_late_init().
Tested on Mac Mini (2020) and Macbook Pro 14-inch (2021).
Signed-off-by: Janne Grunau <[email protected]>
Reviewed-by: Mark Kettenis <[email protected]>
|
|
The BOOT_TARGET_DEVICES list for distro_bootcmd was hard-coded to assume
that all boot devices are available/enabled in the configuration,
thus ignoring the actual config settings. The config_distro_bootcmd.h
header file specifically has compile-time checks to detect such problems.
To allow disabling USB, SCSI, etc. in custom lx2160a board configs,
make it depend on the config settings and use only the enabled features.
Signed-off-by: Daniel Klauer <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Add a multi-function device driver which will probe its children and
provides methods to access the device.
Signed-off-by: Michael Walle <[email protected]>
[Rebased]
Signed-off-by: Priyanka Jain <[email protected]>
|
