| Age | Commit message (Collapse) | Author |
|---|
|
Add function to apply a bitmask to an i2c register, so
that specific bits can be cleared and/or set.
Suggested-by: Simon Glass <[email protected]>
Signed-off-by: Sebastian Reichel <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Update boot-commands to load device-tree from
boot-device at 'fdt_addr_r' address in DDR
during distro-boot.
Signed-off-by: Priyanka Jain <[email protected]>
|
|
Use moveconfig.py script to convert below defines to Kconfig and move
these entries to defconfigs.
CONFIG_CORTINA_FW_ADDR
CONFIG_CORTINA_FW_LENGTH
Signed-off-by: Kuldeep Singh <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
This symbol was largely migrated, except for one case. Update it.
Cc: Priyanka Jain <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
Reviewed-by: Priyanka Jain <[email protected]>
|
|
Use enum efi_memory_type and enum_allocate_type in the definitions of the
efi_allocate_pages(), efi_allocate_pool().
In the external UEFI API leave the type as int as the UEFI specification
explicitely requires that enums use a 32bit type.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Use the same name as in the UEFI specification to avoid confusion.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
For type checking we need an enum.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
This commit adds the comment of the TCG Specification
efi_tcg2.h file refers, and comment for the structure.
Signed-off-by: Masahisa Kojima <[email protected]>
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Define a UCLASS API for verifying ECDSA signatures. Unlike
UCLASS_MOD_EXP, which focuses strictly on modular exponentiation,
the ECDSA class focuses on verification. This is done so that it
better aligns with mach-specific implementations, such as stm32mp.
Signed-off-by: Alexandru Gagniuc <[email protected]>
Reviewed-by: Patrick Delaunay <[email protected]>
|
|
TCG PC Client PFP spec requires to measure
"Exit Boot Services Invocation" if ExitBootServices() is invoked.
Depending upon the return code from the ExitBootServices() call,
"Exit Boot Services Returned with Success" or "Exit Boot Services
Returned with Failure" is also measured.
Signed-off-by: Masahisa Kojima <[email protected]>
Swap two ifs in efi_exit_boot_services().
efi_tcg2_notify_exit_boot_services must have EFIAPI signature.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
TCG PC Client PFP spec requires to measure "Boot####"
and "BootOrder" variables, EV_SEPARATOR event prior
to the Ready to Boot invocation.
Since u-boot does not implement Ready to Boot event,
these measurements are performed when efi_start_image() is called.
TCG spec also requires to measure "Calling EFI Application from
Boot Option" for each boot attempt, and "Returning from EFI
Application from Boot Option" if a boot device returns control
back to the Boot Manager.
Signed-off-by: Masahisa Kojima <[email protected]>
|
|
TCG PC Client PFP spec requires to measure the secure
boot policy before validating the UEFI image.
This commit adds the secure boot variable measurement
of "SecureBoot", "PK", "KEK", "db", "dbx", "dbt", and "dbr".
Note that this implementation assumes that secure boot
variables are pre-configured and not be set/updated in runtime.
Signed-off-by: Masahisa Kojima <[email protected]>
|
|
iPXE used Uri() device path nodes. So we should support them in the
device path to text protocol.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Add Rockchip SFC driver support;
- DTS sync from kernel;
- emmc hs400 support for rk3399;
- Fix for spinore bootdevice and MMC boot order;
|
|
- Some CFI flash related fixups (Kconfig & header) (Bin)
- Enable CFI flash support on the QEMU RISC-V virt machine. (Bin)
|
|
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
|
|
In order to update the DT for rk3188
sync the power domain dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
In order to update the DT for rk3066 and rk3188
sync the clock dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <[email protected]>
Reviewed-by: Heiko Stuebner <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <[email protected]>
Reviewed-by: Kever Yang <[email protected]>
|
|
Enable support to the 2 NOR flashes on the QEMU RISC-V virt machine.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Those embers wrapped with CONFIG_SYS_FLASH_CFI in struct flash_info_t
are unconditionally used in the cfi_flash.c driver.
Drop the #ifdefs in the definition of flash_info_t.
Signed-off-by: Bin Meng <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Enable DM SATA in board file.
Signed-off-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Activate the following Kconfig options:
* AVB for Android Verified Boot support
* ADTIMG for merging DTBOs
* ABOOTIMG for extracting Android boot image
Also rework the partitioning tables:
- add a misc partition to handle BCB messages
- add a dtbo partition to store various DTBOs
- add a vbmeta partition for AVB hashes
- Merge vendor and system into the "super" partition
Note: avb support is disables by default. To activate it:
=> setenv force_avb 1;
=> saveenv;
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
doc/README.gpt states:
> The fields 'uuid' and 'uuid_disk' are optional if CONFIG_RANDOM_UUID is
> enabled. A random uuid will be used if omitted or they point to an empty/
> non-existent environment variable. The environment variable will be
> set to the generated UUID. The 'gpt guid' command reads the current
> value of the uuid_disk from the GPT.
Since we have CONFIG_RANDOM_UUID=y, remove the hard-coded uuids
and use meaningful variable names instead.
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
There is a mix of spaces and tabs at the leading \. This makes updating
theses lines harder.
Add a single space before each \ for some consistency.
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Since Android 10, we are required to use a "dtbo" partition which
includes the various device-tree overlays [1].
It's also possible to provide a "dtb" partition.
This is supported via the "abootimg" command.
On Yukawa, the assumption is that we have only a "dtbo" partition, which
includes all board dtbs and their dtbos [2]
[1] https://source.android.com/devices/architecture/dto/partitions
[2] https://android.googlesource.com/device/amlogic/yukawa/+/refs/heads/master/build/tasks/dtimages.mk#16
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
BOOT_CMD might be different based on CONFIG_CMD_ABOOTIMG.
To prepare for abootimg support, extract the boot command
to a dedicated macro.
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Implement A/B slot selection using the U-Boot ab_select command.
Keep support for non A/B.
Not: We need to redefine the recovery partition label, as RecoveryOS
is included in the boot image for A/B systems [1]
[1] https://source.android.com/devices/tech/ota/ab/ab_implement#recovery
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
AVB (Android Verified Boot) is well supported in U-Boot already.
Add support for it in meson64_android.
This is controlled by the "force_avb" environment variable and the
CONFIG_CMD_AVB option.
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
To prepare for AVB support, increase SYS_MALLOC_LEN to 128M.
This value has been found by testing the following on khadas vim3l:
=> avb init
=> avb verify
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
Permit redefining SYS_MALLOC_LEN for board specific configs.
This is especially useful for Android with AVB, which requires a malloc
length of 128M.
Signed-off-by: Guillaume La Roque <[email protected]>
Signed-off-by: Mattijs Korpershoek <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20210809
- new SOC: add support for imx8ulp
- Toradex fixes for colibri (vf / imx6 / imx7 / imx8x)
- convert to DM for mx28evk
- Fixes for Gateworks ventana boards
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8639
|
|
Use log subsystem for dm_warn()
Various minor bug fixes
|
|
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MX8ULP dtsi
Signed-off-by: Peng Fan <[email protected]>
|
|
i.MX8ULP lpuart has same register layout as i.MX7ULP and i.MX8
Signed-off-by: Peng Fan <[email protected]>
|
|
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.
Signed-off-by: Sebastian Reichel <[email protected]>
|
|
Do not pass the console baudrate to the 'console' variable
to avoid the baudrate being passed twice when extlinux.conf
contains the standard: console=${console},${baudrate} format.
cat /proc/cmdline
root=PARTUUID=00000000-01 rootwait rw console=ttymxc0,115200,115200
Signed-off-by: Fabio Estevam <[email protected]>
|
|
After the conversion to DM_MMC, the rootfs becomes mmc 1, so
adjust it accordingly.
Signed-off-by: Fabio Estevam <[email protected]>
|
|
At present it is possible to call uclass_get() before driver model is
inited. In fact this happens on x86 boards which use Intel FSPv1, since
mrccache_get_region() tries to get the SPI flash device very early
during init.
This has always been undefined behaviour. Previously it generally worked,
i.e. returned an error code without crashing, because gd->uclass_root_s
is zeroed and the uclass can be added despite driver model not being
ready, due to the way lists are implemented. With the change to use a
gd->uclass_root pointer, this no-longer works. For example, it causes a
hang on minnowmax.
Fix this by adding a check that driver model is ready when uclass_get() is
called. This function is called in the process of locating any device, so
it is a good place to add the check.
This fixes booting on minnowmax.
Signed-off-by: Simon Glass <[email protected]>
Fixes: 8a715530bb1 ("dm: core: Allow the uclass list to move")
|
|
Migrate the dm_warn function to log macro with
LOGC_DM category and LOGL_WARNING level.
This macro allows filtering with log command and allows
output on all log backend.
Signed-off-by: Patrick Delaunay <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The bootparams do not have to be at fixed location, they can be
dynamically mallocated instead. Make it so to get rid of another
fixed assignment.
Signed-off-by: Marek Vasut <[email protected]>
Cc: Biju Das <[email protected]>
Cc: Lad Prabhakar <[email protected]>
|
|
These boards have been removed. Drop the config file and other references.
Signed-off-by: Simon Glass <[email protected]>
|
