| Age | Commit message (Collapse) | Author |
|---|
|
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Add Support for the same.
Signed-off-by: Faiz Abbas <[email protected]>
|
|
In preparation for addition of ADMA2 support, cleanup SDMA handling by
moving it to a new sdhci_prepare_dma() function. Also add a flags field
in sdhci_host to indicate if DMA is enabled.
Signed-off-by: Faiz Abbas <[email protected]>
|
|
- Various btrfs fixes
- Various TI platform fixes
- Other fixes (cross build, taurus update, Kconfig help text)
|
|
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <[email protected]>
Reviewed-by: Lokesh Vutla <[email protected]>
|
|
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <[email protected]>
|
|
The existing comments where confusing read and write. The comment for
fs_write() had:
"@addr: The address to read into"
So let's rework the comments and format them in Sphinx style.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
|
|
If SCSI is enabled, U-Boot should try to boot also from SCSI device on
Turris Omnia.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
The I2C dependencies are defined in include/configs/turris_omnia.h,
because Turris Omnia won't boot correctly without I2C support.
Move these dependencies to Kconfig, so that they are selected if Turris
Omnia is selected as target.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Heiko Schocher <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
These are not needed if MMC and SCSI DM drivers are used.
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Amend the unit test 'start image exit' to transfer a string as exit data.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
In case of a failure exit data may be passed to Exit() which in turn is
returned by StartImage().
Let the `bootefi` command print the exit data string in case of an error.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
The field boot OptionalData in structure _EFI_LOAD_OPTIONS is for binary
data.
When we use `efidebug boot add` we should convert the 5th argument from
UTF-8 to UTF-16 before putting it into the BootXXXX variable.
When printing boot variables with `efidebug boot dump` we should support
the OptionalData being arbitrary binary data. So let's dump the data as
hexadecimal values.
Here is an example session protocol:
=> efidebug boot add 00a1 label1 scsi 0:1 doit1 'my option'
=> efidebug boot add 00a2 label2 scsi 0:1 doit2
=> efidebug boot dump
Boot00A0:
attributes: A-- (0x00000001)
label: label1
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit1
data:
00000000: 6d 00 79 00 20 00 6f 00 70 00 74 00 69 00 6f 00 m.y. .o.p.t.i.o.
00000010: 6e 00 00 00 n...
Boot00A1:
attributes: A-- (0x00000001)
label: label2
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit2
data:
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Improvements and new features:
- improved SPI driver for better read throughput
- refactors initialisation of debug UART init
- restructures header file paths
- adds pinctrl improvements
Adds Kever as a co-custodian.
|
|
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
|
|
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <[email protected]>
Reviewed-by: Philipp Tomsich <[email protected]>
|
|
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <[email protected]>
[trini: Re-run migration]
Signed-off-by: Tom Rini <[email protected]>
|
|
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
[1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22
[2]: https://github.com/OP-TEE/optee_os/pull/2699
Reviewed-by: Simon Glass <[email protected]>
Reviewed-by: Sam Protsenko <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
SYSFW version 2019.01 introduces a slightly modified version of this API,
add support for it here.
Signed-off-by: Andrew F. Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Andreas Dannenberg <[email protected]>
|
|
TI-SCI message protocol provides support for controlling the firewall
configurations available in SoC.
Introduce support for the set of TI-SCI message protocol APIs that
provide us with this capability of controlling firewalls.
Signed-off-by: Andrew F. Davis <[email protected]>
Reviewed-by: Tom Rini <[email protected]>
Reviewed-by: Andreas Dannenberg <[email protected]>
|
|
adding a new bootstage ID:
BOOTSTAGE_ID_ENTER_CLI_LOOP
Signed-off-by: Heiko Schocher <[email protected]>
|
|
- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
|
|
|
|
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Heiko Schocher <[email protected]>
Cc: Tom Rini <[email protected]>
Cc: Michal Simek <[email protected]>
Cc: "Marek Behún" <[email protected]>
Cc: Daniel Schwierzeck <[email protected]>
Cc: Maxim Sloyko <[email protected]>
Cc: Erik van Luijk <[email protected]>
Cc: Ryder Lee <[email protected]>
Cc: Weijie Gao <[email protected]>
Cc: Simon Glass <[email protected]>
Cc: "Álvaro Fernández Rojas" <[email protected]>
Cc: Philippe Reynes <[email protected]>
Cc: Christophe Leroy <[email protected]>
Reviewed-by: Michal Simek <[email protected]>
Tested-by: Michal Simek <[email protected]> (on zcu100)
|
|
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
We have run now multiple times into size issues with the openrd
board port. To finally fix this, this patch now moves the U-Boot size
from 0x6.0000 to 0x8.0000, giving enough space for the next time.
This also changes the environment location and potentially the
MTD partitioning, but I see no better fix for now. Especially since
this board does not have an active maintainer.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Chris Packham <[email protected]>
Reviewed-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed
as CONFIG_ENV_OFFSET is also set to the same value.
Signed-off-by: Stefan Roese <[email protected]>
Cc: Chris Packham <[email protected]>
Reviewed-by: Chris Packham <[email protected]>
Signed-off-by: Stefan Roese <[email protected]>
|
|
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Tested-by: Marcel Ziswiler <[email protected]>
Signed-off-by: Igor Opaniuk <[email protected]>
|
|
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs.
Signed-off-by: Pierre-Jean Texier <[email protected]>
Signed-off-by: Joris Offouga <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
Port for the DART-6UL Evaluation Kit SBC. Based on the variscite
DART-6UL iMX6ULL SoM.
CPU: Freescale i.MX6ULL rev1.1 900 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 43C
Reset cause: POR
Model: Variscite DART-6UL Evaluation Kit
Board: Variscite DART-6UL Evaluation Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2c
- MMC/SD
- eMMC
- USB host
- UART 1
Note: LCDIF porting needs DM_VIDEO
https://lists.denx.de/pipermail/u-boot/2019-April/365506.html
Signed-off-by: Parthiban Nallathambi <[email protected]>
|
|
Fix fdt_file and console to boot upstream Linux Kernel.
Upstream linux use imx8qxp-mek.dtb, and pass lpuart32 to earlycon
will not work for i.MX8QXP, only need to pass earlycon,
check drivers/tty/serial/earlycon.c,
" /* Just 'earlycon' is a valid param for devicetree and ACPI SPCR. */ "
Signed-off-by: Peng Fan <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
After DM conversion, U-Boot is larger than 512 KiB, so we need to increase
the "size" of the dfu_alt_info setting.
Signed-off-by: Pierre-Jean Texier <[email protected]>
Acked-by: Joris Offouga <[email protected]>
Reviewed-by: Fabio Estevam <[email protected]>
|
|
After DM conversion, the size of U-Boot binary to increase.
Previous size is 480K after DM Conversion the new size is 557K
So it's necessary to increase the dfu request for store u-boot-dtb.img in eMMC.
Signed-off-by: Joris Offouga <[email protected]>
|
|
Migrate Ethernet FEC to using driver model.
Drop PHY_MICREL_KSZ90X1 which slipped in from Apalis iMX6.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
Migrate MMC to using driver model.
Migrate USDHC to using pinctrl.
While at it also add GPIO1_IO03__OSC32K_32K_OUT pin muxing.
While at it also update copyright period.
Signed-off-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
Currently $loadaddr and $fdt_addr_r point to the same address. This
might be not ideal for some distro boot scripts which make use of
$loadaddr after loading the device tree.
Make sure the two variables point to two different addresses. Moving
$loadaddr is not entirly trivial since it is defined in mx6_common.h.
Move $fdt_addr_r and $ramdisk_addr_r by 1MiB, which should be enough
for scripts.
Signed-off-by: Stefan Agner <[email protected]>
Acked-by: Marcel Ziswiler <[email protected]>
Reviewed-by: Igor Opaniuk <[email protected]>
|
|
Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT
Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2
U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
CPU: NXP i.MX8QM RevB A53 at 142933 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW 9330215b
Boot: SD1
DRAM: 6 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial@5a060000
Out: serial@5a060000
Err: serial@5a060000
Net:
Error: ethernet@5b040000 address not set.
eth-1: ethernet@5b040000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MX8QM clocks definition
Signed-off-by: Peng Fan <[email protected]>
|
|
Add i.MX8QM pads definition
Signed-off-by: Peng Fan <[email protected]>
|
|
This converts the following to Kconfig:
CONFIG_USB_EHCI_MX5
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
After i.MX5's EHCI conversion to DM, the CONFIG_MXC_USB_PORT is not needed
anymore and should be removed.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
After unification of the rootfs for both HSC and DDC devices, only one,
common wic file is necessary - without the distinction of specific board.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
After switching to DM/DTS support of esdhc3 - the code in this patch
can be removed.
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
The CONFIG_FSL_ESDHC is now enabled and defined in Kconfig, not in
include/configs/kp_imx53.h
Signed-off-by: Lukasz Majewski <[email protected]>
|
|
Instead of hardcoding the mmcroot to /dev/mmcblkX, use the UUID
method.
Signed-off-by: Adam Ford <[email protected]>
|
|
This adds an extra, optional environmental variable called
'optargs' which if enabled allow additional parameters to be
passed to the kernel (ie, quiet, cma=128M, etc.)
Each script that setups the bootargs will just append this.
Signed-off-by: Adam Ford <[email protected]>
|
|
Move HUSH_PARSER to defconfig, otherwise meet
"
=> run netboot
Booting from net ...
Unknown command 'if' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
Unknown command '0x80280000' - try 'help'
Unknown command 'if' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'then' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
Unknown command 'else' - try 'help'
Unknown command 'fi' - try 'help'
"
Signed-off-by: Peng Fan <[email protected]>
|
|
Remove outdated defines (not used any more, outdated due to DM
conversion) from various socfpga files in include/config.
Signed-off-by: Simon Goldschmidt <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Series-version: 3
Series-changes: 2
- added (this) patch with further cleanups to the socfpga board config
files
|
|
socfpga_common.h defines CONFIG_SYS_BOOTMAPSZ to 64 MiB.
Since having this define overrides the 'bootm_size' env variable for
the whole socfpga platform, let's remove this define from socfpga_common.h
and instead rely on the 'bootm_size' env variable (which is initialized
to 160 MiB in the same file's default env). This gives users the
chance to override it in their own environment.
Signed-off-by: Simon Goldschmidt <[email protected]>
Acked-by: Marek Vasut <[email protected]>
Series-to: Marek Vasut <[email protected]>
Series-to: [email protected]
Cover-letter:
arm: socfpga: clean up socfpga_common.h
This series cleans up the include/configs/socfpga_common.h file a bit.
It removes some defines that are used nowhere and cleans up some
leftovers after various subsystems have been converted to use DM.
END
|
|
Remove outdated macros and comments (not used any more, outdated due to
DM conversion) from socfpga_common.h.
Signed-off-by: Simon Goldschmidt <[email protected]>
Series-changes: 3
- changed commit message: s/defines/macros and comments/
Series-changes: 2
- remove even more outdated things
|
