| Age | Commit message (Collapse) | Author |
|---|
|
While converting to binman for an imx8mq board, it has been found that
building in the u-boot CI fails. This is because an imx8mq requires an
external binary (signed_hdmi_imx8m.bin). If this file cannot be found
mkimage fails.
To be able to build this board in the u-boot CI a binman option
(--fake-ext-blobs) is introduced that can be switched on via the u-boot
makefile option BINMAN_FAKE_EXT_BLOBS. With that the needed dummy files are
created.
Signed-off-by: Heiko Thiery <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Recent changes caused fields in the image main header to be modified
after the header checksum had already been computed. Move the checksum
computation to once again be the last operation performed on the header.
Fixes: 2b0980c24027 ("tools: kwbimage: Fill the real header size into the main header")
Signed-off-by: Pierre Bourdon <[email protected]>
Reviewed-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-01-rc4-4
UEFI:
* allow for more than 16 KiB UEFI variable size when using StMM
Others:
* make watchdog sysreset compatible with separate poweroff driver
* avoid OpenSSL deprecation warnings
|
|
Our Gitlab CI buildsystem is set up to treat warnings as errors.
With OpenSSL 3.0 a lot of deprecation warnings occur.
With the patch compatibility with OpenSSL 1.1.1 is declared.
In the long run we should upgrade our code to use the current API.
A -Wdiscarded-qualifiers warning is muted by casting.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
rk3568 is the first SoC which supports idb header v2.
Signed-off-by: Kever Yang <[email protected]>
|
|
Rockchip BootRom supports new idb header v2 instead of legacy version.
Add support for it so that we can generate image for new SoCs.
Signed-off-by: Yi Liu <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
|
|
We are going to have more than one version header, add the version in the
header info.
Signed-off-by: Kever Yang <[email protected]>
|
|
The first 4byte of idbimage is a magic number instead of signature,
correct it.
Signed-off-by: Kever Yang <[email protected]>
|
|
Commit "fw_setenv: lock the flash only if it was locked before"
checks for Locked status with uninitialized erase data.
Address by moving the test for MEMISLOCKED.
Fixes: 8a726b852502 ("fw_setenv: lock the flash only if it was locked before")
Signed-off-by: Joakim Tjernlund <[email protected]>
|
|
Cap end of relocations by the binary size.
Linkers like to insert some auxiliary sections between .rela.dyn and
.bss_start. These sections don't make their way to the final binary, but
reloc_rela still tries to relocate them, resulting in attempted read
past the end of file.
When linking U-Boot with ld.lld, the STATIC_RELA feature (enabled by
default on arm64) breaks the build. After this patch, U-Boot can be
linked successfully with and without CONFIG_STATIC_RELA.
Originally-from: Elena Petrova <[email protected]>
Signed-off-by: Alistair Delva <[email protected]>
Cc: David Brazdil <[email protected]>
Cc: Scott Wood <[email protected]>
Cc: Tom Rini <[email protected]>
|
|
Signed-off-by: Tom Rini <[email protected]>
|
|
For testing the TPM drivers and the EFI_TCG2_PROTOCOL we need the tool
swtpm.
Once we move to Ubuntu Impish we can take libtpms from package libtpms-dev.
Signed-off-by: Heinrich Schuchardt <[email protected]>
|
|
Fix some copy&paste artifacts.
Signed-off-by: Jan Kiszka <[email protected]>
|
|
WIth EFI we must embed the devicetree in an ELF image so that it is loaded
as part of the executable file. We want it to include the binman
definition in there also, which in some cases cannot be created until the
ELF (u-boot) is built. Add an option to binman to support writing the
updated dtb to the ELF file u-boot.out
This is useful with the EFI app, which is always packaged as an ELF file.
Signed-off-by: Simon Glass <[email protected]>
|
|
The comment for this function is missing an argument and the return value.
Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
Binman needs to be able to update the contents of an ELF file after it has
been build. To support this, add a function to locate the position of a
symbol's contents within the file.
Fix the comments on bss_data.c and Symbol while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
At present any error from the 'make' command is silently swallowed by the
test system. Fix this by showing it when detected.
Signed-off-by: Simon Glass <[email protected]>
|
|
The Exception base class is a very vague and could be confusing to the
test system. Use the more specific ValueError exception instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
Quite a lot of the code in common/relates to booting and images. Before
adding more it seems like a good time to move the code into its own
directory.
Most files with 'boot' or 'image' in them are moved, except:
- autoboot.c which relates to U-Boot automatically running a script
- bootstage.c which relates to U-Boot timing
Drop the removal of boot* files from the output directory, since this
interfers with the symlinks created by tools and there does not appear
to be any such file from my brief testing.
Signed-off-by: Simon Glass <[email protected]>
Reviewed-by: Artem Lapkin <[email protected]>
Tested-by: Artem Lapkin <[email protected]>
|
|
Field srcaddr in kwbimage v0 needs to be adjusted similarly like in v1.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Kwbimage v0 has similar alignment requirements as v1.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Fill the real header size without padding into the main header
This allows to reduce final image when converting image to another format
which does not need additional padding.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Currently kwbimage header is always aligned to 4096 bytes. But it does not
have to be aligned to such a high value.
The header needs to be just 4-byte aligned, while some image types have
additional alignment restrictions.
This change reduces size of kwbimage binaries by removing extra padding
between header and data part.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This change allows to convert image from one format to another without need
to include unnecessary padding (e.g. when target image format has smaller
alignment requirement as source image format).
Do it by storing real image data size without padding to the kwbimage
header.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
xmodem block size is 128 bytes, therefore it is possible to transfer only
images with size multiple of 128 bytes. kwboot automatically pads image
with zero bytes at the end to align it to 128 bytes boundary.
Do this padding when generating image to allow uploading with other xmodem
tools or older kwboot versions.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
There are more unused enums and function prototypes. Remove them. The
function kwbimage_check_params() does not return enum kwbimage_cmd_types,
but a boolean value returned as int.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
kwbimage v0 sldo has 32-bit data checksum at the end like kwbimage v1.
Use same data checksum validation for both v0 and v1 image types.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
kwbimage must have valid blockid member instead of zero value. Thus if
config file does not contain BOOT_FROM command, use by default the value
for SPI booting (which is probably the most common).
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
For documentation purposes update struct main_hdr_v0 to include information
where version of the image must be stored. For kwbimage v0 it obviously
must be 0. By default all image header memory is initialized to zero,
therefore this change has no functional effect.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
These two commands allow to specify custom setting of UART port used for
printing BootROM messages.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
It is useful to see kwboot version in the boot log output for debugging
purposes.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Properly calculate and align image header size to xmodem block size.
Kirkwood v0 images do not have stored total size of header in header
structure itself like it is for v1 images. So kwbheader_size() calculates
size by traversing image structure itself. Aligning is done in kwboot by
putting zero padding bytes between the header and data part.
Signed-off-by: Pali Rohár <[email protected]>
Tested-by: Tony Dinh <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
After successful transfer of whole image only two things can happen:
- BootROM starts execution of data block, which changes UART baudrate
back to 115200 Bd,
- board crashes and causes CPU reset
In both cases UART baudrate is reset to the default speed. So there is
no need to send special magic sequence to inform kwboot that baudrate is
going to be reset and kwboot does not need to wait for this event and
can do it immediately after BootROM acknowledges end of xmodem transfer.
Move ARM code for sending magic sequence from main baudrate change
section to binhdr_pre section which is executed only before changing
baudrate from the default value of 115200 Bd to some new value. Remove
kwboot code waiting for magic sequence after successful xmodem transfer.
Rationale: sometimes when using very high UART speeds, magic sequence is
damaged and kwboot fails at this last stage. Removal of this magic
sequence makes booting more stable.
Data transfer protocol (xmodem) is using checksums and retransmit, so it
already deals with possible errors on transfer line.
Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
The ARM code we inject into the image to change baudrate back to the
default value of 115200 Baud, which is run after successful UART transfer
of the whole image, cannot use stack as at this stage stack pointer is not
initialized yet.
Stack can only be used when BootROM is executing binary header, to
preserve state of registers, since BootROM expects that.
Change the ARM baudrate code to not use stack at all and put binary
header specific pre + post code (which stores and restores registers) into
separate arrays.
The baudrate change code now jumps at it's end and expects that there is
either code which returns to the BootROM or jumps to the original exec
address.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Older Armada SoCs have custom ARMv5te compatible core which does not
support movt instruction. So replace mov + movt instruction pair used for
immediate move construction by mov + orr instructions which are supported
also by ARMv5te.
After this change kwboot ARM code should be compatible with any 32-bit ARM
core compatible by ARMv2 or new. At least GNU AS does not throw any error
or warning.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Increase loop cycles from 600000 to 2998272, which should increase delay
from 1ms to about 5ms on 1200 MHz CPU.
The Number 2998272 was chosen as the nearest value around 3000000 which can
be encoded into one ARM mov instruction. It avoids usage of movt instruction
which is not supported by ARMv5te cores.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Kwboot puts each xmodem packet to kernel queue, then waits until all bytes
of that packet are transmitted over UART and then waits for xmodem reply
until it is received into kernel queue.
If some reply is received during the time we are waiting until all bytes
are transmitted, then kernel puts them into the queue and returns it to
kwboot in next read() call.
So there is no need to wait (with tcdrain() function) until all bytes from
xmodem packet are transmitted over UART, since any reply received either
during that time or after is returned to kwboot with the next read().
Therefore do not call tcdrain() after each xmodem packet sent. Instead
directly wait for any reply after putting xmodem packet into write kernel
queue.
This change could speed up xmodem transfer in case tcdrain() function waits
for a longer time.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
After the trasfer of last header packet, it is possible that baudrate
change pattern is received, and also that NAK byte is received so that
the packet should be sent again.
Thus we should not clear the baudrate change state when sending retry
of that packet.
Move code for initializing state variables from kwboot_xm_recv_reply()
to kwboot_xm_sendblock().
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Currently when kwboot receive some garbage reply which does not understand,
it waits 1s before it tries to resend packet again.
The most common error on UART is that receiver sees some bit flipped which
results in invalid reply.
This behavior slows down xmodem transfer over UART as basically on every
error kwboot is waiting one second.
To fix this, try to resend xmodem packet for first 3 attempts immediately
without any delay. If broken reply is received also after the 3 attempts,
continue retrying with 1s delay like it was before.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This patch does not change behavior of the code, just allows to implement
new changes more easily.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
kwboot_img_grow_hdr()
Size of the header stored in kwbimage may be larger than real used size in
the kwbimage header. If there is unused space in kwbimage header then use
it for growing it. So update code to calculate used space of kwbimage
header.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
This ensures that kwboot_img_grow_hdr() function still sees valid kwbimage
header.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Expression (hdrsz % KWBOOT_XM_BLKSZ) is non-zero therefore expression
(KWBOOT_XM_BLKSZ - hdrsz % KWBOOT_XM_BLKSZ) is always less than value
KWBOOT_XM_BLKSZ. So there is no need to add another modulo. Also rename
variable `offset` to `grow` which better describes what is stored in
this variable.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
It is hard to debug why kwboot is failing when the last message is
'Finishing transfer' and no additional output. So show verbose message when
kwboot finished transfer and is waiting for baudrate change magic sequence.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
For kwbimage v1, tell BootROM to send BootROM messages to UART port number
0 (used also for UART booting) with default baudrate (which should be
115200) and do not touch UART MPP configuration.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
If data part of image is modified, update 4-byte data checksum.
It looks like A385 BootROM does not verify this checksum for image
loaded via UART, but we do not know if other BootROMs are also ignoring
it. It is always better to provide correct checksum.
Signed-off-by: Pali Rohár <[email protected]>
[ refactored ]
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Some vendor U-Boot kwbimage binaries (e.g. those for A375) have load
address set to zero. Therefore it is not possible to inject code which
changes baudrate back to 115200 Bd before the data part.
So instead inject it after the data part and change kwbimage execution
address to that offset. Also store original execution address into
baudrate change code, so after it changes baudrate back to 115200 Bd, it
can jump to orignal address.
Signed-off-by: Pali Rohár <[email protected]>
[ refactored ]
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Data part of the image contains 4-byte checksum. Validate it when
processing the image.
Signed-off-by: Pali Rohár <[email protected]>
[ refactored ]
Signed-off-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
SPI image header and data parts do not have to be aligned to 128 byte
xmodem block size. So reserve additional memory for aligning header part
and additional memory for aligning data part.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
|
Explicitly disable 2 stop bits by clearing CSTOPB flag, disable modem
control flow by clearing CRTSCTS flag and do not send hangup after closing
device by clearing HUPCL flag.
Signed-off-by: Pali Rohár <[email protected]>
Reviewed-by: Marek Behún <[email protected]>
Reviewed-by: Stefan Roese <[email protected]>
|
