| Age | Commit message (Collapse) | Author |
|---|
|
Add a test for this code, adjusting the timestamp on various files to
check each use case.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add a test for this code. It requires some defconfig files and a test
Kconfig to work with, so copy these into the temporary directory at the
start.
Signed-off-by: Simon Glass <[email protected]>
|
|
Rather than using the global thoughout each function, pass in these
values. This allows tests to use different values when testing the same
functions.
Improve a few comments while we are here.
No functional change is intended.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not needed anymore, so drop it.
Signed-off-by: Simon Glass <[email protected]>
Fixes: 252ed872 ("kconfig: remove meaningless prefixes in defconfig files")
|
|
Use names consistent with their target names.
Signed-off-by: Simon Glass <[email protected]>
|
|
Test should return a suitable exit code when they fail. Fix this and tidy
up the code a little.
Signed-off-by: Simon Glass <[email protected]>
|
|
The -D option is used, but plumb it through --debug to enable a full
traceback when something goes wrong.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix the typo in the RunTests() function, adding comments while we are
here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add test for u_boot_spl_pubkey_dtb. The test adds a public key to the
dtb and checks if the required nodes will be added to the images dtb.
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add documentation for the 'bootgen' bintool
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This adds a new etype 'u-boot-spl-pubkey-dtb'. The etype adds the public
key from a certificate to the dtb. This creates a '/signature' node which
is turn contains the fields which make up the public key. Usually this
is done by 'mkimage -K'. However, 'binman sign' does not add the public
key to the SPL. This is why the pubkey is added using this etype.
The etype calls the underlying 'fdt_add_pubkey' tool.
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add btool which calls 'fdt_add_pubkey'
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add documentation for btool which calls 'fdt_add_pubkey'
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The method 'connect_contents_to_file()' calls ObtainsContents() with
'fake_size' argument. Without providing the argument in the blob_dtb
we are not able to call this method without error.
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
While signing a fit compressed data (i.e. 'blob-ext') is decompressed,
but never compressed again. When compressed data was wrapped in a
section, decompression leads to an error because the outer section had
the original compressed size but the inner entry has the
uncompressed size now.
While singing there is no reason to decompress data. Thus, decompression
should be disabled.
Furthermore, bintools should be collected before loading the data. This
way bintools are available if processing is required on a node.
Signed-off-by: Lukas Funke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Add tests to reach 100% code coverage for the added etype encrypted.
Signed-off-by: Christian Taedcke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
The new encrypted etype generates a cipher node in the device tree
that should not be evaluated by binman, but still be kept in the
output device tree.
Signed-off-by: Christian Taedcke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
This adds a new etype encrypted.
It creates a new cipher node in the related image similar to the
cipher node used by u-boot, see boot/image-cipher.c.
Signed-off-by: Christian Taedcke <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
Rerun 'binman bintool-docs' to regenerate bintools.rst
Signed-off-by: Simon Glass <[email protected]>
|
|
These have ended up with the same numbers as earlier files. Fix them.
Signed-off-by: Simon Glass <[email protected]>
|
|
These have ended up with the same numbers as earlier files. Fix them.
Signed-off-by: Simon Glass <[email protected]>
|
|
Drop the use of a numbered key file since numbering is just for the test
devicetree files. Also adjust the tests to avoid putting a hard-coded
path to binman in the file, using the entry arg instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
At this point, buildman requires a few different modules and so we need
a requirements.txt to track what modules are needed.
Cc: Simon Glass <[email protected]>
Cc: Neha Malcom Francis <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Neha Malcom Francis <[email protected]>
Signed-off-by: Tom Rini <[email protected]>
|
|
Without this re-building will fail with an error when trying to create
the symlink for the second time with an already exists error.
Signed-off-by: Andrew Davis <[email protected]>
[[email protected]: Added support for test output dir and testcase]
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
Since binman is used to package bootloader images for all K3 devices, we
do not have to rely on the earlier methods to package them.
Scripts that were used to generate x509 certificate for tiboot3.bin and
generate tispl.bin, u-boot.img have been removed.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
The ti-secure entry contains certificate for binaries that will be
loaded or booted by system firmware whereas the ti-secure-rom entry
contains certificate for binaries that will be booted by ROM. Support
for both these types of certificates is necessary for booting of K3
devices.
Reviewed-by: Simon Glass <[email protected]>
[[email protected]: fixed inconsist cert generation by multiple packing]
Signed-off-by: Vignesh Raghavendra <[email protected]>
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
The ti-board-config entry loads and validates a given YAML config file
against a given schema, and generates the board config binary. K3
devices require these binaries to be packed into the final system
firmware images.
Reviewed-by: Simon Glass <[email protected]>
Signed-off-by: Neha Malcom Francis <[email protected]>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
|
|
Update my and DPs email address to match current setup.
Signed-off-by: Michal Simek <[email protected]>
Link: https://lore.kernel.org/r/aba5b19b9c5a95608829e86ad5cc4671c940f1bb.1688992543.git.michal.simek@amd.com
|
|
https://source.denx.de/u-boot/custodians/u-boot-dm
binman mkimage and template enhancements
misc fixes
|
|
These are not very important message. Change them to use the 'debug' level
instead of 'detail'.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add support for writing symbols and determining the assumed position of
binaries inside a mkimage image. This is useful as an example for other
entry types which might want to do the same thing.
Signed-off-by: Simon Glass <[email protected]>
|
|
Allow templates to be used inside a section, not just in the top-level
/binman node.
Signed-off-by: Simon Glass <[email protected]>
|
|
Add this as a separate test case.
Signed-off-by: Simon Glass <[email protected]>
|
|
Allow a template to appear in the top level description when using
multiple images.
Signed-off-by: Simon Glass <[email protected]>
|
|
Collections can used to collect the contents of other entries into a
single entry, but they result in a single entry, with the original entries
'left behind' in their old place.
It is useful to be able to specific a set of entries ones and have it used
in multiple images, or parts of an image.
Implement this mechanism.
Signed-off-by: Simon Glass <[email protected]>
|
|
Provide a way to specify a phandle list of nodes which are to be inserted
into an existing node.
Signed-off-by: Simon Glass <[email protected]>
|
|
This permits implementation of a simple templating system, where a node
can be reused as a base for others.
For now this adds new subnodes after any existing ones.
Signed-off-by: Simon Glass <[email protected]>
|
|
Fix the check for the __bss_size symbol, since it may be 0. Unfortunately
there was no test coverage for this.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is not needed since the linker script sets it up. Drop the variable
to avoid confusion.
Fix the prototype for main() while we are here.
Signed-off-by: Simon Glass <[email protected]>
|
|
Sometimes multiple boards are built with binman and it is useful to
specify a different FDT list for each. At present this is not possible
without providing multiple values of the of-list entryarg (which is not
supported in the U-Boot build system).
Allow a fit,fdt-list-val string-list property to be used instead.
Signed-off-by: Simon Glass <[email protected]>
|
|
This is needed to handle mkimage with inner section located itself in a
section.
Signed-off-by: Marek Vasut <[email protected]>
Use BuildSectionData() instead of ObtainContents(), add tests and a few
other minor fixes:
Signed-off-by: Simon Glass <[email protected]>
|
|
This area of binman can be a bit confusing. Add some more comments to
help.
Signed-off-by: Simon Glass <[email protected]>
|
|
Update the LookupAndWriteSymbols() function to return the number of
symbols written. Also add some logging for when debugging is not
enabled.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some boards don't use symbol writing but do access the symbols in SPL.
Provide an option to work around this.
Signed-off-by: Simon Glass <[email protected]>
|
|
Move this to the ReadEntries() function where it belongs.
Signed-off-by: Simon Glass <[email protected]>
|
|
Some section types don't have a simple _entries list. Use the GetEntries()
method in GetEntryContents() and other places to handle this.
This makes the behaviour more consistent.
Signed-off-by: Simon Glass <[email protected]>
|
|
This should be set up in the init function, to avoid a warning about a
property not set up there. Fix it.
Signed-off-by: Simon Glass <[email protected]>
|
|
When building from source, setuptools would complain about not finding
package via its auto-discovery mechanism. Manually specify how to
locate the files, relative to the package's directory.
* tools/u_boot_pylib/pyproject.toml: New tool.setuptools.packages.find
section.
Signed-off-by: Maxim Cournoyer <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
|
* tools/u_boot_pylib/pyproject.toml (readme): Replace README.md with
README.rst.
Signed-off-by: Maxim Cournoyer <[email protected]>
Reviewed-by: Simon Glass <[email protected]>
|
