From 57285737cbae4638112a96e4b3ee78eda6182b6e Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Sun, 2 Apr 2023 01:17:07 +0100 Subject: sunxi: dts: arm/arm64: update devicetree files from Linux-v6.4-rc2 Sync the devicetree files from the official Linux kernel tree, v6.4-rc2. This is covering both 64-bit and 32-bit Allwinner SoCs with Arm Ltd. cores, we skip the new RISC-V bits for now, as sunxi RISC-V support is still work in progress. Among smaller cosmetic changes, this adds a SATA regulator node which we need in U-Boot to get rid of hard-coded GPIOs. Also this updates the Allwinner F1C100s DTs, enabling USB support, and also adds the DTs for two new boards. As before, this omits the non-backwards compatible changes to the R_INTC controller, to remain compatible with older kernels. Signed-off-by: Andre Przywara --- arch/arm/dts/axp22x.dtsi | 6 +++ arch/arm/dts/axp809.dtsi | 7 +++ arch/arm/dts/axp81x.dtsi | 14 ----- arch/arm/dts/sun50i-a64.dtsi | 1 + arch/arm/dts/sun50i-h5-orangepi-pc2.dts | 1 + arch/arm/dts/sun5i-gr8-chip-pro.dts | 2 +- arch/arm/dts/sun5i-r8-chip.dts | 2 +- arch/arm/dts/sun6i-a31.dtsi | 12 ++--- arch/arm/dts/sun6i-a31s-sina31s.dts | 2 +- arch/arm/dts/sun8i-a23-a33.dtsi | 10 ++-- arch/arm/dts/sun8i-a33.dtsi | 1 + arch/arm/dts/sun8i-a83t-bananapi-m3.dts | 15 ++++++ arch/arm/dts/sun8i-h3-beelink-x2.dts | 2 +- arch/arm/dts/sun8i-h3-nanopi-duo2.dts | 2 +- arch/arm/dts/sun8i-v3s.dtsi | 6 +-- arch/arm/dts/suniv-f1c100s-licheepi-nano.dts | 16 ++++++ arch/arm/dts/suniv-f1c100s.dtsi | 32 +++++++++++ arch/arm/dts/suniv-f1c200s-lctech-pi.dts | 76 ++++++++++++++++++++++++++ arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts | 81 ++++++++++++++++++++++++++++ arch/arm/dts/sunxi-h3-h5.dtsi | 8 +-- 20 files changed, 259 insertions(+), 37 deletions(-) create mode 100644 arch/arm/dts/suniv-f1c200s-lctech-pi.dts create mode 100644 arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts diff --git a/arch/arm/dts/axp22x.dtsi b/arch/arm/dts/axp22x.dtsi index a020c12b288..f79650afd0a 100644 --- a/arch/arm/dts/axp22x.dtsi +++ b/arch/arm/dts/axp22x.dtsi @@ -67,6 +67,12 @@ status = "disabled"; }; + axp_gpio: gpio { + compatible = "x-powers,axp221-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + regulators { /* Default work frequency for buck regulators */ x-powers,dcdc-freq = <3000>; diff --git a/arch/arm/dts/axp809.dtsi b/arch/arm/dts/axp809.dtsi index ab8e5f2d924..d134d4c00bd 100644 --- a/arch/arm/dts/axp809.dtsi +++ b/arch/arm/dts/axp809.dtsi @@ -50,4 +50,11 @@ compatible = "x-powers,axp809"; interrupt-controller; #interrupt-cells = <1>; + + axp_gpio: gpio { + compatible = "x-powers,axp809-gpio", + "x-powers,axp221-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; }; diff --git a/arch/arm/dts/axp81x.dtsi b/arch/arm/dts/axp81x.dtsi index b93387b0c1c..ebaf1c3ce8d 100644 --- a/arch/arm/dts/axp81x.dtsi +++ b/arch/arm/dts/axp81x.dtsi @@ -62,16 +62,6 @@ compatible = "x-powers,axp813-gpio"; gpio-controller; #gpio-cells = <2>; - - gpio0_ldo: gpio0-ldo-pin { - pins = "GPIO0"; - function = "ldo"; - }; - - gpio1_ldo: gpio1-ldo-pin { - pins = "GPIO1"; - function = "ldo"; - }; }; battery_power_supply: battery-power { @@ -144,15 +134,11 @@ }; reg_ldo_io0: ldo-io0 { - pinctrl-names = "default"; - pinctrl-0 = <&gpio0_ldo>; /* Disable by default to avoid conflicts with GPIO */ status = "disabled"; }; reg_ldo_io1: ldo-io1 { - pinctrl-names = "default"; - pinctrl-0 = <&gpio1_ldo>; /* Disable by default to avoid conflicts with GPIO */ status = "disabled"; }; diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi index b04f492c0f2..135762b34fd 100644 --- a/arch/arm/dts/sun50i-a64.dtsi +++ b/arch/arm/dts/sun50i-a64.dtsi @@ -1197,6 +1197,7 @@ compatible = "allwinner,sun50i-a64-mipi-dphy", "allwinner,sun6i-a31-mipi-dphy"; reg = <0x01ca1000 0x1000>; + interrupts = ; clocks = <&ccu CLK_BUS_MIPI_DSI>, <&ccu CLK_DSI_DPHY>; clock-names = "bus", "mod"; diff --git a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts index b5c1ff19b4c..ce3ae19e72d 100644 --- a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts @@ -3,6 +3,7 @@ /dts-v1/; #include "sun50i-h5.dtsi" +#include "sun50i-h5-cpu-opp.dtsi" #include #include diff --git a/arch/arm/dts/sun5i-gr8-chip-pro.dts b/arch/arm/dts/sun5i-gr8-chip-pro.dts index a32cde3e32e..5c3562b85a5 100644 --- a/arch/arm/dts/sun5i-gr8-chip-pro.dts +++ b/arch/arm/dts/sun5i-gr8-chip-pro.dts @@ -70,7 +70,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "chip-pro:white:status"; gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/dts/sun5i-r8-chip.dts b/arch/arm/dts/sun5i-r8-chip.dts index 4bf4943d4eb..fd37bd1f392 100644 --- a/arch/arm/dts/sun5i-r8-chip.dts +++ b/arch/arm/dts/sun5i-r8-chip.dts @@ -70,7 +70,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "chip:white:status"; gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/dts/sun6i-a31.dtsi b/arch/arm/dts/sun6i-a31.dtsi index f6701ece7b7..b32d2ab6aa2 100644 --- a/arch/arm/dts/sun6i-a31.dtsi +++ b/arch/arm/dts/sun6i-a31.dtsi @@ -820,7 +820,7 @@ clocks = <&ccu CLK_APB2_UART0>; resets = <&ccu RST_APB2_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -833,7 +833,7 @@ clocks = <&ccu CLK_APB2_UART1>; resets = <&ccu RST_APB2_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -846,7 +846,7 @@ clocks = <&ccu CLK_APB2_UART2>; resets = <&ccu RST_APB2_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -859,7 +859,7 @@ clocks = <&ccu CLK_APB2_UART3>; resets = <&ccu RST_APB2_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -872,7 +872,7 @@ clocks = <&ccu CLK_APB2_UART4>; resets = <&ccu RST_APB2_UART4>; dmas = <&dma 10>, <&dma 10>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -885,7 +885,7 @@ clocks = <&ccu CLK_APB2_UART5>; resets = <&ccu RST_APB2_UART5>; dmas = <&dma 22>, <&dma 22>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; diff --git a/arch/arm/dts/sun6i-a31s-sina31s.dts b/arch/arm/dts/sun6i-a31s-sina31s.dts index 0af48e143b6..56956352914 100644 --- a/arch/arm/dts/sun6i-a31s-sina31s.dts +++ b/arch/arm/dts/sun6i-a31s-sina31s.dts @@ -67,7 +67,7 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "sina31s:status:usr"; gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ }; diff --git a/arch/arm/dts/sun8i-a23-a33.dtsi b/arch/arm/dts/sun8i-a23-a33.dtsi index 06809c3a1f2..84c6d9379a3 100644 --- a/arch/arm/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/dts/sun8i-a23-a33.dtsi @@ -488,7 +488,7 @@ clocks = <&ccu CLK_BUS_UART0>; resets = <&ccu RST_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -501,7 +501,7 @@ clocks = <&ccu CLK_BUS_UART1>; resets = <&ccu RST_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -514,7 +514,7 @@ clocks = <&ccu CLK_BUS_UART2>; resets = <&ccu RST_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -527,7 +527,7 @@ clocks = <&ccu CLK_BUS_UART3>; resets = <&ccu RST_BUS_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -540,7 +540,7 @@ clocks = <&ccu CLK_BUS_UART4>; resets = <&ccu RST_BUS_UART4>; dmas = <&dma 10>, <&dma 10>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; diff --git a/arch/arm/dts/sun8i-a33.dtsi b/arch/arm/dts/sun8i-a33.dtsi index b3d1bdfb511..30fdd2703b1 100644 --- a/arch/arm/dts/sun8i-a33.dtsi +++ b/arch/arm/dts/sun8i-a33.dtsi @@ -278,6 +278,7 @@ dphy: d-phy@1ca1000 { compatible = "allwinner,sun6i-a31-mipi-dphy"; reg = <0x01ca1000 0x1000>; + interrupts = ; clocks = <&ccu CLK_BUS_MIPI_DSI>, <&ccu CLK_DSI_DPHY>; clock-names = "bus", "mod"; diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts index b60016a4429..197cf6959b5 100644 --- a/arch/arm/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/dts/sun8i-a83t-bananapi-m3.dts @@ -105,6 +105,21 @@ /* enables internal regulator and de-asserts reset */ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */ }; + + /* + * Power supply for the SATA disk, behind a USB-SATA bridge. + * Since it is a USB device, there is no consumer in the DT, so we + * have to keep this always on. + */ + regulator-sata-disk-pwr { + compatible = "regulator-fixed"; + regulator-name = "sata-disk-pwr"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + enable-active-high; + gpio = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */ + }; }; &cpu0 { diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts index 27a0d51289d..a6d38ecee14 100644 --- a/arch/arm/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts @@ -57,7 +57,7 @@ ethernet1 = &sdiowifi; }; - cec-gpio { + cec { compatible = "cec-gpio"; cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */ hdmi-phandle = <&hdmi>; diff --git a/arch/arm/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts index 43641cb8239..343b02b9715 100644 --- a/arch/arm/dts/sun8i-h3-nanopi-duo2.dts +++ b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts @@ -57,7 +57,7 @@ regulator-ramp-delay = <50>; /* 4ms */ enable-active-high; - enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ gpios-states = <0x1>; states = <1100000 0>, <1300000 1>; diff --git a/arch/arm/dts/sun8i-v3s.dtsi b/arch/arm/dts/sun8i-v3s.dtsi index db194c606fd..b001251644f 100644 --- a/arch/arm/dts/sun8i-v3s.dtsi +++ b/arch/arm/dts/sun8i-v3s.dtsi @@ -479,7 +479,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART0>; status = "disabled"; }; @@ -492,7 +492,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART1>; status = "disabled"; }; @@ -505,7 +505,7 @@ reg-io-width = <4>; clocks = <&ccu CLK_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; resets = <&ccu RST_BUS_UART2>; pinctrl-0 = <&uart2_pins>; pinctrl-names = "default"; diff --git a/arch/arm/dts/suniv-f1c100s-licheepi-nano.dts b/arch/arm/dts/suniv-f1c100s-licheepi-nano.dts index 04e59b8381c..43896723a99 100644 --- a/arch/arm/dts/suniv-f1c100s-licheepi-nano.dts +++ b/arch/arm/dts/suniv-f1c100s-licheepi-nano.dts @@ -6,6 +6,8 @@ /dts-v1/; #include "suniv-f1c100s.dtsi" +#include + / { model = "Lichee Pi Nano"; compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s"; @@ -50,8 +52,22 @@ }; }; +&otg_sram { + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pe_pins>; status = "okay"; }; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; /* PE2 */ + status = "okay"; +}; diff --git a/arch/arm/dts/suniv-f1c100s.dtsi b/arch/arm/dts/suniv-f1c100s.dtsi index 9455d27e516..3c61d59ab5f 100644 --- a/arch/arm/dts/suniv-f1c100s.dtsi +++ b/arch/arm/dts/suniv-f1c100s.dtsi @@ -133,6 +133,32 @@ #size-cells = <0>; }; + usb_otg: usb@1c13000 { + compatible = "allwinner,suniv-f1c100s-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ccu CLK_BUS_OTG>; + resets = <&ccu RST_BUS_OTG>; + interrupts = <26>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + allwinner,sram = <&otg_sram 1>; + status = "disabled"; + }; + + usbphy: phy@1c13400 { + compatible = "allwinner,suniv-f1c100s-usb-phy"; + reg = <0x01c13400 0x10>; + reg-names = "phy_ctrl"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb0_phy"; + resets = <&ccu RST_USB_PHY0>; + reset-names = "usb0_reset"; + #phy-cells = <1>; + status = "disabled"; + }; + ccu: clock@1c20000 { compatible = "allwinner,suniv-f1c100s-ccu"; reg = <0x01c20000 0x400>; @@ -181,6 +207,12 @@ pins = "PE0", "PE1"; function = "uart0"; }; + + /omit-if-no-ref/ + uart1_pa_pins: uart1-pa-pins { + pins = "PA2", "PA3"; + function = "uart1"; + }; }; i2c0: i2c@1c27000 { diff --git a/arch/arm/dts/suniv-f1c200s-lctech-pi.dts b/arch/arm/dts/suniv-f1c200s-lctech-pi.dts new file mode 100644 index 00000000000..2d2a3f026df --- /dev/null +++ b/arch/arm/dts/suniv-f1c200s-lctech-pi.dts @@ -0,0 +1,76 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2022 Arm Ltd, + * based on work: + * Copyright 2022 Icenowy Zheng + */ + +/dts-v1/; +#include "suniv-f1c100s.dtsi" + +#include + +/ { + model = "Lctech Pi F1C200s"; + compatible = "lctech,pi-f1c200s", "allwinner,suniv-f1c200s", + "allwinner,suniv-f1c100s"; + + aliases { + serial0 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_vcc3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&mmc0 { + broken-cd; + bus-width = <4>; + disable-wp; + vmmc-supply = <®_vcc3v3>; + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pc_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pa_pins>; + status = "okay"; +}; + +/* + * This is a Type-C socket, but CC1/2 are not connected, and VBUS is connected + * to Vin, which supplies the board. Host mode works (if the board is powered + * otherwise), but peripheral is probably the intention. + */ +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts b/arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts new file mode 100644 index 00000000000..184c245041a --- /dev/null +++ b/arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2022 Icenowy Zheng + */ + +/dts-v1/; +#include "suniv-f1c100s.dtsi" + +#include +#include + +/ { + model = "Popcorn Computer PopStick v1.1"; + compatible = "sourceparts,popstick-v1.1", "sourceparts,popstick", + "allwinner,suniv-f1c200s", "allwinner,suniv-f1c100s"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&pio 4 6 GPIO_ACTIVE_HIGH>; /* PE6 */ + linux,default-trigger = "heartbeat"; + }; + }; + + reg_vcc3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&mmc0 { + cd-gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */ + bus-width = <4>; + disable-wp; + vmmc-supply = <®_vcc3v3>; + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pc_pins>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-max-frequency = <40000000>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pe_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi index fc1af9b608b..bdc796f4622 100644 --- a/arch/arm/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/dts/sunxi-h3-h5.dtsi @@ -709,7 +709,7 @@ clocks = <&ccu CLK_BUS_UART0>; resets = <&ccu RST_BUS_UART0>; dmas = <&dma 6>, <&dma 6>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -722,7 +722,7 @@ clocks = <&ccu CLK_BUS_UART1>; resets = <&ccu RST_BUS_UART1>; dmas = <&dma 7>, <&dma 7>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -735,7 +735,7 @@ clocks = <&ccu CLK_BUS_UART2>; resets = <&ccu RST_BUS_UART2>; dmas = <&dma 8>, <&dma 8>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -748,7 +748,7 @@ clocks = <&ccu CLK_BUS_UART3>; resets = <&ccu RST_BUS_UART3>; dmas = <&dma 9>, <&dma 9>; - dma-names = "rx", "tx"; + dma-names = "tx", "rx"; status = "disabled"; }; -- cgit v1.2.3 From b0816e3bd38d0273bbc6fce1fe87fd842991733c Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Tue, 11 Apr 2023 23:56:14 +0100 Subject: sunxi: defconfig: Add Lctech Pi F1C200s board The Lctech Pi F1C200s (also previously known under the Cherry Pi brand) is a small development board with the Allwinner F1C200s SoC. This is the same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM. Add a defconfig for this board, enabling the most basic features. This uses the new 64MB memory map, which avoids the very tight memory map we use for the 32MB F1C100s board(s). The devicetree file is already in the tree, courtesy of the previous Linux repo sync. Signed-off-by: Andre Przywara --- configs/lctech_pi_f1c200s_defconfig | 11 +++++++++++ 1 file changed, 11 insertions(+) create mode 100644 configs/lctech_pi_f1c200s_defconfig diff --git a/configs/lctech_pi_f1c200s_defconfig b/configs/lctech_pi_f1c200s_defconfig new file mode 100644 index 00000000000..310719cf915 --- /dev/null +++ b/configs/lctech_pi_f1c200s_defconfig @@ -0,0 +1,11 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_DEFAULT_DEVICE_TREE="suniv-f1c200s-lctech-pi" +CONFIG_SPL=y +CONFIG_MACH_SUNIV=y +CONFIG_DRAM_CLK=156 +CONFIG_DRAM_ZQ=0 +CONFIG_SUNXI_MINIMUM_DRAM_MB=64 +# CONFIG_VIDEO_SUNXI is not set +CONFIG_CONS_INDEX=2 +CONFIG_SPI=y -- cgit v1.2.3 From 9bc6f1a4d08261032d60836ea1dd6f2e98889060 Mon Sep 17 00:00:00 2001 From: Sam Edwards Date: Fri, 12 May 2023 15:22:14 -0600 Subject: sunxi: Fix typo in include guard Signed-off-by: Sam Edwards Reviewed-by: Andre Przywara --- arch/arm/include/asm/arch-sunxi/pmic_bus.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/include/asm/arch-sunxi/pmic_bus.h b/arch/arm/include/asm/arch-sunxi/pmic_bus.h index 3ccfe138f39..5ab9b2809f2 100644 --- a/arch/arm/include/asm/arch-sunxi/pmic_bus.h +++ b/arch/arm/include/asm/arch-sunxi/pmic_bus.h @@ -6,7 +6,7 @@ */ #ifndef _SUNXI_PMIC_BUS_H -#define _SUNXI_PMIS_BUS_H +#define _SUNXI_PMIC_BUS_H int pmic_bus_init(void); int pmic_bus_read(u8 reg, u8 *data); -- cgit v1.2.3