From 6921b314a855b3c4856ef5ef83315fe945de98b2 Mon Sep 17 00:00:00 2001 From: Sanjeev Premi Date: Mon, 18 Jul 2011 09:20:15 -0400 Subject: omap3evm: eth: split function setup_net_chip In current implementation, the function sets up the ethernet chip and resets it. The steps to reset depend upon the board revision. The patch moves the reset actions to new function reset_net_chip(). Signed-off-by: Sanjeev Premi Signed-off-by: Sandeep Paulraj --- board/ti/evm/evm.c | 12 +++++++++++- board/ti/evm/evm.h | 1 + 2 files changed, 12 insertions(+), 1 deletion(-) (limited to 'board') diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index aaf3033b04a..8f9f141682f 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -130,6 +130,9 @@ int misc_init_r(void) #endif omap3_evm_get_revision(); +#if defined(CONFIG_CMD_NET) + reset_net_chip(); +#endif dieid_num_r(); return 0; @@ -153,7 +156,6 @@ void set_muxconf_regs(void) */ static void setup_net_chip(void) { - struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE; struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; /* Configure GPMC registers */ @@ -172,6 +174,14 @@ static void setup_net_chip(void) /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, &ctrl_base->gpmc_nadv_ale); +} + +/** + * Reset the ethernet chip. + */ +static void reset_net_chip(void) +{ + struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE; /* Make GPIO 64 as output pin */ writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe); diff --git a/board/ti/evm/evm.h b/board/ti/evm/evm.h index b721ad6af5e..623cf1bb18d 100644 --- a/board/ti/evm/evm.h +++ b/board/ti/evm/evm.h @@ -49,6 +49,7 @@ u32 get_omap3_evm_rev(void); #if defined(CONFIG_CMD_NET) static void setup_net_chip(void); +static void reset_net_chip(void); #endif /* -- cgit v1.3.1 From c06825873dbc977028c393cb9cbe320634cb5785 Mon Sep 17 00:00:00 2001 From: Sriramakrishnan Date: Mon, 18 Jul 2011 09:21:55 -0400 Subject: omap3evm: Update ethernet reset sequence for Rev.G board The GPIO pin used for resetting the external LAN chip has changed for Rev.G board. The patch uses generic gpio API instead of direct access to corresponding registers. Signed-off-by: Sriramakrishnan Signed-off-by: Sanjeev Premi Signed-off-by: Sandeep Paulraj --- board/ti/evm/evm.c | 35 ++++++++++++++++++++++++++--------- 1 file changed, 26 insertions(+), 9 deletions(-) (limited to 'board') diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index 8f9f141682f..2c95fae68cf 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -33,10 +33,14 @@ #include #include #include +#include #include #include #include "evm.h" +#define OMAP3EVM_GPIO_ETH_RST_GEN1 64 +#define OMAP3EVM_GPIO_ETH_RST_GEN2 7 + DECLARE_GLOBAL_DATA_PTR; static u32 omap3_evm_version; @@ -181,17 +185,30 @@ static void setup_net_chip(void) */ static void reset_net_chip(void) { - struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE; - - /* Make GPIO 64 as output pin */ - writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe); - - /* Now send a pulse on the GPIO pin */ - writel(GPIO0, &gpio3_base->setdataout); + int ret; + int rst_gpio; + + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) { + rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN1; + } else { + rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN2; + } + + ret = omap_request_gpio(rst_gpio); + if (ret < 0) { + printf("Unable to get GPIO %d\n", rst_gpio); + return ; + } + + /* Configure as output */ + omap_set_gpio_direction(rst_gpio, 0); + + /* Send a pulse on the GPIO pin */ + omap_set_gpio_dataout(rst_gpio, 1); udelay(1); - writel(GPIO0, &gpio3_base->cleardataout); + omap_set_gpio_dataout(rst_gpio, 0); udelay(1); - writel(GPIO0, &gpio3_base->setdataout); + omap_set_gpio_dataout(rst_gpio, 1); } int board_eth_init(bd_t *bis) -- cgit v1.3.1 From 5626f336caa7d19e7a79bd836a221a6899dc70b5 Mon Sep 17 00:00:00 2001 From: Sanjeev Premi Date: Mon, 18 Jul 2011 09:23:00 -0400 Subject: omap3evm: eth: Include functions only when necessary These functions are not required when CONFIG_CMD_NET is not defined: - setup_net_chip() - reset_net_chip() - board_eth_init() This patch wraps them in #ifdef CONFIG_CMD_NET...#endif Signed-off-by: Sanjeev Premi Signed-off-by: Sandeep Paulraj --- board/ti/evm/evm.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'board') diff --git a/board/ti/evm/evm.c b/board/ti/evm/evm.c index 2c95fae68cf..30c1c570f16 100644 --- a/board/ti/evm/evm.c +++ b/board/ti/evm/evm.c @@ -153,6 +153,7 @@ void set_muxconf_regs(void) MUX_EVM(); } +#ifdef CONFIG_CMD_NET /* * Routine: setup_net_chip * Description: Setting up the configuration GPMC registers specific to the @@ -219,3 +220,4 @@ int board_eth_init(bd_t *bis) #endif return rc; } +#endif /* CONFIG_CMD_NET */ -- cgit v1.3.1 From 0bf98f1d13224b0c7a18c72f4aaa6a04df982a47 Mon Sep 17 00:00:00 2001 From: Laurence Withers Date: Mon, 18 Jul 2011 09:25:58 -0400 Subject: DaVinci: rename gpio_defs.h to gpio.h In preparation for a generic GPIO driver for the DA8xx processors, rename to and fix up all files which include it. Signed-off-by: Laurence Withers Signed-off-by: Sandeep Paulraj --- arch/arm/include/asm/arch-davinci/gpio.h | 66 +++++++++++++++++++++++++++ arch/arm/include/asm/arch-davinci/gpio_defs.h | 66 --------------------------- board/davinci/dm355leopard/dm355leopard.c | 2 +- board/davinci/dm365evm/dm365evm.c | 2 +- drivers/usb/musb/da8xx.h | 2 +- 5 files changed, 69 insertions(+), 69 deletions(-) create mode 100644 arch/arm/include/asm/arch-davinci/gpio.h delete mode 100644 arch/arm/include/asm/arch-davinci/gpio_defs.h (limited to 'board') diff --git a/arch/arm/include/asm/arch-davinci/gpio.h b/arch/arm/include/asm/arch-davinci/gpio.h new file mode 100644 index 00000000000..1be2ac26604 --- /dev/null +++ b/arch/arm/include/asm/arch-davinci/gpio.h @@ -0,0 +1,66 @@ +/* + * Copyright (C) 2009 Texas Instruments Incorporated + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _GPIO_DEFS_H_ +#define _GPIO_DEFS_H_ + +#ifndef CONFIG_SOC_DA8XX +#define DAVINCI_GPIO_BINTEN 0x01C67008 +#define DAVINCI_GPIO_BANK01 0x01C67010 +#define DAVINCI_GPIO_BANK23 0x01C67038 +#define DAVINCI_GPIO_BANK45 0x01C67060 +#define DAVINCI_GPIO_BANK67 0x01C67088 + +#else /* CONFIG_SOC_DA8XX */ +#define DAVINCI_GPIO_BINTEN 0x01E26008 +#define DAVINCI_GPIO_BANK01 0x01E26010 +#define DAVINCI_GPIO_BANK23 0x01E26038 +#define DAVINCI_GPIO_BANK45 0x01E26060 +#define DAVINCI_GPIO_BANK67 0x01E26088 +#endif /* CONFIG_SOC_DA8XX */ + +struct davinci_gpio { + unsigned int dir; + unsigned int out_data; + unsigned int set_data; + unsigned int clr_data; + unsigned int in_data; + unsigned int set_rising; + unsigned int clr_rising; + unsigned int set_falling; + unsigned int clr_falling; + unsigned int intstat; +}; + +struct davinci_gpio_bank { + int num_gpio; + unsigned int irq_num; + unsigned int irq_mask; + unsigned long *in_use; + unsigned long base; +}; + +#define davinci_gpio_bank01 ((struct davinci_gpio *)DAVINCI_GPIO_BANK01) +#define davinci_gpio_bank23 ((struct davinci_gpio *)DAVINCI_GPIO_BANK23) +#define davinci_gpio_bank45 ((struct davinci_gpio *)DAVINCI_GPIO_BANK45) +#define davinci_gpio_bank67 ((struct davinci_gpio *)DAVINCI_GPIO_BANK67) + +#endif diff --git a/arch/arm/include/asm/arch-davinci/gpio_defs.h b/arch/arm/include/asm/arch-davinci/gpio_defs.h deleted file mode 100644 index 1be2ac26604..00000000000 --- a/arch/arm/include/asm/arch-davinci/gpio_defs.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * Copyright (C) 2009 Texas Instruments Incorporated - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#ifndef _GPIO_DEFS_H_ -#define _GPIO_DEFS_H_ - -#ifndef CONFIG_SOC_DA8XX -#define DAVINCI_GPIO_BINTEN 0x01C67008 -#define DAVINCI_GPIO_BANK01 0x01C67010 -#define DAVINCI_GPIO_BANK23 0x01C67038 -#define DAVINCI_GPIO_BANK45 0x01C67060 -#define DAVINCI_GPIO_BANK67 0x01C67088 - -#else /* CONFIG_SOC_DA8XX */ -#define DAVINCI_GPIO_BINTEN 0x01E26008 -#define DAVINCI_GPIO_BANK01 0x01E26010 -#define DAVINCI_GPIO_BANK23 0x01E26038 -#define DAVINCI_GPIO_BANK45 0x01E26060 -#define DAVINCI_GPIO_BANK67 0x01E26088 -#endif /* CONFIG_SOC_DA8XX */ - -struct davinci_gpio { - unsigned int dir; - unsigned int out_data; - unsigned int set_data; - unsigned int clr_data; - unsigned int in_data; - unsigned int set_rising; - unsigned int clr_rising; - unsigned int set_falling; - unsigned int clr_falling; - unsigned int intstat; -}; - -struct davinci_gpio_bank { - int num_gpio; - unsigned int irq_num; - unsigned int irq_mask; - unsigned long *in_use; - unsigned long base; -}; - -#define davinci_gpio_bank01 ((struct davinci_gpio *)DAVINCI_GPIO_BANK01) -#define davinci_gpio_bank23 ((struct davinci_gpio *)DAVINCI_GPIO_BANK23) -#define davinci_gpio_bank45 ((struct davinci_gpio *)DAVINCI_GPIO_BANK45) -#define davinci_gpio_bank67 ((struct davinci_gpio *)DAVINCI_GPIO_BANK67) - -#endif diff --git a/board/davinci/dm355leopard/dm355leopard.c b/board/davinci/dm355leopard/dm355leopard.c index 0ee0d11a71b..0ad5678106e 100644 --- a/board/davinci/dm355leopard/dm355leopard.c +++ b/board/davinci/dm355leopard/dm355leopard.c @@ -20,7 +20,7 @@ #include #include #include -#include +#include #include #include #include diff --git a/board/davinci/dm365evm/dm365evm.c b/board/davinci/dm365evm/dm365evm.c index 5fb76111b4a..ac541062514 100644 --- a/board/davinci/dm365evm/dm365evm.c +++ b/board/davinci/dm365evm/dm365evm.c @@ -22,7 +22,7 @@ #include #include #include -#include +#include #include #include #ifdef CONFIG_DAVINCI_MMC diff --git a/drivers/usb/musb/da8xx.h b/drivers/usb/musb/da8xx.h index b9660ba8097..be1cdaf1dc7 100644 --- a/drivers/usb/musb/da8xx.h +++ b/drivers/usb/musb/da8xx.h @@ -25,7 +25,7 @@ #define __DA8XX_MUSB_H__ #include -#include +#include #include "musb_core.h" /* Base address of da8xx usb0 wrapper */ -- cgit v1.3.1 From 469ec1e35354e45dce48299248c641367ed9e68a Mon Sep 17 00:00:00 2001 From: Aneesh V Date: Thu, 21 Jul 2011 09:10:01 -0400 Subject: omap4: cleanup pin mux data - separate mux settings into essential and non essential parts - essential part is board independent as of now(so move it to SoC directory). Will help in having single SPL for all boards. - Non-essential part(the pins not essential for u-boot to function) need to be phased out eventually. - Correct mux data by aligning to the latest settings in x-loader Signed-off-by: Aneesh V Signed-off-by: Sandeep Paulraj --- arch/arm/cpu/armv7/omap4/board.c | 53 +++++- arch/arm/cpu/armv7/omap4/omap4_mux_data.h | 76 ++++++++ arch/arm/include/asm/arch-omap4/sys_proto.h | 4 +- board/ti/panda/panda.c | 25 +-- board/ti/panda/panda.h | 264 ---------------------------- board/ti/panda/panda_mux_data.h | 230 ++++++++++++++++++++++++ board/ti/sdp4430/sdp.c | 25 +-- board/ti/sdp4430/sdp.h | 264 ---------------------------- board/ti/sdp4430/sdp4430_mux_data.h | 230 ++++++++++++++++++++++++ 9 files changed, 601 insertions(+), 570 deletions(-) create mode 100644 arch/arm/cpu/armv7/omap4/omap4_mux_data.h delete mode 100644 board/ti/panda/panda.h create mode 100644 board/ti/panda/panda_mux_data.h delete mode 100644 board/ti/sdp4430/sdp.h create mode 100644 board/ti/sdp4430/sdp4430_mux_data.h (limited to 'board') diff --git a/arch/arm/cpu/armv7/omap4/board.c b/arch/arm/cpu/armv7/omap4/board.c index de4cc2ab84a..3fd6f8459f8 100644 --- a/arch/arm/cpu/armv7/omap4/board.c +++ b/arch/arm/cpu/armv7/omap4/board.c @@ -31,17 +31,65 @@ #include #include #include +#include "omap4_mux_data.h" DECLARE_GLOBAL_DATA_PTR; +void do_set_mux(u32 base, struct pad_conf_entry const *array, int size) +{ + int i; + struct pad_conf_entry *pad = (struct pad_conf_entry *) array; + + for (i = 0; i < size; i++, pad++) + writew(pad->val, base + pad->offset); +} + +static void set_muxconf_regs_essential(void) +{ + do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_essential, + sizeof(core_padconf_array_essential) / + sizeof(struct pad_conf_entry)); + + do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_essential, + sizeof(wkup_padconf_array_essential) / + sizeof(struct pad_conf_entry)); +} + +static void set_mux_conf_regs(void) +{ + switch (omap4_hw_init_context()) { + case OMAP_INIT_CONTEXT_SPL: + set_muxconf_regs_essential(); + break; + case OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL: + set_muxconf_regs_non_essential(); + break; + case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR: + case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH: + set_muxconf_regs_essential(); + set_muxconf_regs_non_essential(); + break; + } +} + /* * Routine: s_init - * Description: Does early system init of muxing and clocks. - * - Called path is with SRAM stack. + * Description: Does early system init of watchdog, muxing, andclocks + * Watchdog disable is done always. For the rest what gets done + * depends on the boot mode in which this function is executed + * 1. s_init of SPL running from SRAM + * 2. s_init of U-Boot running from FLASH + * 3. s_init of U-Boot loaded to SDRAM by SPL + * 4. s_init of U-Boot loaded to SDRAM by ROM code using the + * Configuration Header feature + * Please have a look at the respective functions to see what gets + * done in each of these cases + * This function is called with SRAM stack. */ void s_init(void) { watchdog_init(); + set_mux_conf_regs(); } /* @@ -124,7 +172,6 @@ int checkboard(void) */ int arch_cpu_init(void) { - set_muxconf_regs(); return 0; } diff --git a/arch/arm/cpu/armv7/omap4/omap4_mux_data.h b/arch/arm/cpu/armv7/omap4/omap4_mux_data.h new file mode 100644 index 00000000000..00c52f835f2 --- /dev/null +++ b/arch/arm/cpu/armv7/omap4/omap4_mux_data.h @@ -0,0 +1,76 @@ + /* + * (C) Copyright 2010 + * Texas Instruments Incorporated, + * + * Balaji Krishnamoorthy + * Aneesh V + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _OMAP4_MUX_DATA_H_ +#define _OMAP4_MUX_DATA_H_ + +#include + +const struct pad_conf_entry core_padconf_array_essential[] = { + +{GPMC_AD0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat0 */ +{GPMC_AD1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat1 */ +{GPMC_AD2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat2 */ +{GPMC_AD3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat3 */ +{GPMC_AD4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat4 */ +{GPMC_AD5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat5 */ +{GPMC_AD6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat6 */ +{GPMC_AD7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat7 */ +{GPMC_NOE, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M1)}, /* sdmmc2_clk */ +{GPMC_NWE, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_cmd */ +{SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */ +{SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */ +{SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */ +{SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */ +{SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */ +{SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */ +{SDMMC1_DAT4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat4 */ +{SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */ +{SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */ +{SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */ +{I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */ +{I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */ +{I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */ +{I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */ +{I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */ +{I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */ +{I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */ +{I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */ +{UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */ +{UART3_RTS_SD, (M0)}, /* uart3_rts_sd */ +{UART3_RX_IRRX, (IEN | M0)}, /* uart3_rx */ +{UART3_TX_IRTX, (M0)} /* uart3_tx */ + +}; + +const struct pad_conf_entry wkup_padconf_array_essential[] = { + +{PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */ +{PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */ +{PAD1_SYS_32K, (IEN | M0)} /* sys_32k */ + +}; + +#endif /* _OMAP4_MUX_DATA_H_ */ diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index 6b596b48988..3624378f206 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -24,6 +24,7 @@ #include #include #include +#include struct omap_sysinfo { char *board_string; @@ -33,7 +34,8 @@ extern const struct omap_sysinfo sysinfo; void gpmc_init(void); void watchdog_init(void); u32 get_device_type(void); -void set_muxconf_regs(void); +void do_set_mux(u32 base, struct pad_conf_entry const *array, int size); +void set_muxconf_regs_non_essential(void); void sr32(void *, u32, u32, u32); u32 wait_on_value(u32, u32, void *, u32); void sdelay(unsigned long); diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index 78e19107978..9afed807b08 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -25,7 +25,7 @@ #include #include -#include "panda.h" +#include "panda_mux_data.h" DECLARE_GLOBAL_DATA_PTR; @@ -65,27 +65,14 @@ int misc_init_r(void) return 0; } -void do_set_mux(u32 base, struct pad_conf_entry const *array, int size) +void set_muxconf_regs_non_essential(void) { - int i; - struct pad_conf_entry *pad = (struct pad_conf_entry *) array; - - for (i = 0; i < size; i++, pad++) - writew(pad->val, base + pad->offset); -} - -/** - * @brief set_muxconf_regs Setting up the configuration Mux registers - * specific to the board. - */ -void set_muxconf_regs(void) -{ - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array, - sizeof(core_padconf_array) / + do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + sizeof(core_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array, - sizeof(wkup_padconf_array) / + do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + sizeof(wkup_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); } diff --git a/board/ti/panda/panda.h b/board/ti/panda/panda.h deleted file mode 100644 index e3d090e5691..00000000000 --- a/board/ti/panda/panda.h +++ /dev/null @@ -1,264 +0,0 @@ -/* - * (C) Copyright 2010 - * Texas Instruments Incorporated, - * - * Balaji Krishnamoorthy - * Aneesh V - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef _PANDA_H_ -#define _PANDA_H_ - -#include -#include - -const struct pad_conf_entry core_padconf_array[] = { - {GPMC_AD0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat0 */ - {GPMC_AD1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat1 */ - {GPMC_AD2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat2 */ - {GPMC_AD3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat3 */ - {GPMC_AD4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat4 */ - {GPMC_AD5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat5 */ - {GPMC_AD6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat6 */ - {GPMC_AD7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat7 */ - {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ - {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ - {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ - {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ - {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ - {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ - {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ - {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ - {GPMC_A16, (M3)}, /* gpio_40 */ - {GPMC_A17, (PTD | M3)}, /* gpio_41 */ - {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ - {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ - {GPMC_A20, (IEN | M3)}, /* gpio_44 */ - {GPMC_A21, (M3)}, /* gpio_45 */ - {GPMC_A22, (M3)}, /* gpio_46 */ - {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ - {GPMC_A24, (PTD | M3)}, /* gpio_48 */ - {GPMC_A25, (PTD | M3)}, /* gpio_49 */ - {GPMC_NCS0, (M3)}, /* gpio_50 */ - {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ - {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ - {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ - {GPMC_NWP, (M3)}, /* gpio_54 */ - {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ - {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ - {GPMC_NOE, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M1)}, /* sdmmc2_clk */ - {GPMC_NWE, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_cmd */ - {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ - {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ - {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ - {GPMC_WAIT1, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_62 */ - {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ - {C2C_DATA12, (PTU | IEN | M3)}, /* gpio_101 */ - {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ - {C2C_DATA14, (M1)}, /* dsi2_te0 */ - {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ - {HDMI_HPD, (M0)}, /* hdmi_hpd */ - {HDMI_CEC, (M0)}, /* hdmi_cec */ - {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ - {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ - {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ - {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ - {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ - {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ - {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ - {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ - {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ - {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ - {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ - {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ - {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ - {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ - {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ - {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ - {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ - {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ - {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ - {USBB1_ULPITLL_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M4)},/* usbb1_ulpiphy_clk */ - {USBB1_ULPITLL_STP, (OFF_EN | OFF_OUT_PTD | M4)}, /* usbb1_ulpiphy_stp */ - {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dir */ - {USBB1_ULPITLL_NXT, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_nxt */ - {USBB1_ULPITLL_DAT0, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat0 */ - {USBB1_ULPITLL_DAT1, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat1 */ - {USBB1_ULPITLL_DAT2, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat2 */ - {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat3 */ - {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */ - {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */ - {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */ - {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */ - {USBB1_HSIC_DATA, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_data */ - {USBB1_HSIC_STROBE, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_strobe */ - {USBC1_ICUSB_DP, (IEN | M0)}, /* usbc1_icusb_dp */ - {USBC1_ICUSB_DM, (IEN | M0)}, /* usbc1_icusb_dm */ - {SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */ - {SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */ - {SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */ - {SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */ - {SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */ - {SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */ - {SDMMC1_DAT4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat4 */ - {SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */ - {SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */ - {SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */ - {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ - {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ - {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ - {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ - {ABE_MCBSP1_CLKX, (IEN | M1)}, /* abe_slimbus1_clock */ - {ABE_MCBSP1_DR, (IEN | M1)}, /* abe_slimbus1_data */ - {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ - {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ - {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ - {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ - {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ - {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ - {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ - {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ - {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ - {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */ - {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ - {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */ - {UART2_RTS, (M0)}, /* uart2_rts */ - {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */ - {UART2_TX, (M0)}, /* uart2_tx */ - {HDQ_SIO, (M3)}, /* gpio_127 */ - {I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */ - {I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */ - {I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */ - {I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */ - {I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */ - {I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */ - {I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */ - {I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */ - {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ - {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ - {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ - {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ - {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ - {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ - {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ - {UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */ - {UART3_RTS_SD, (M0)}, /* uart3_rts_sd */ - {UART3_RX_IRRX, (IEN | M0)}, /* uart3_rx */ - {UART3_TX_IRTX, (M0)}, /* uart3_tx */ - {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ - {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ - {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ - {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ - {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ - {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ - {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ - {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ - {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ - {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ - {UART4_RX, (IEN | M0)}, /* uart4_rx */ - {UART4_TX, (M0)}, /* uart4_tx */ - {USBB2_ULPITLL_CLK, (IEN | M3)}, /* gpio_157 */ - {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ - {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ - {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ - {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ - {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ - {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ - {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ - {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ - {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ - {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ - {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ - {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ - {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ - {UNIPRO_TX0, (PTD | IEN | M3)}, /* gpio_171 */ - {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ - {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ - {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ - {UNIPRO_TX2, (PTU | IEN | M3)}, /* gpio_0 */ - {UNIPRO_TY2, (PTU | IEN | M3)}, /* gpio_1 */ - {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ - {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ - {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ - {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ - {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ - {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ - {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */ - {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */ - {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */ - {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ - {FREF_CLK2_OUT, (PTU | IEN | M3)}, /* gpio_182 */ - {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ - {SYS_NIRQ2, (PTU | IEN | M0)}, /* sys_nirq2 */ - {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ - {SYS_BOOT1, (M3)}, /* gpio_185 */ - {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ - {SYS_BOOT3, (M3)}, /* gpio_187 */ - {SYS_BOOT4, (M3)}, /* gpio_188 */ - {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ - {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ - {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ - {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ - {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ - {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ - {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ - {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ - {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ - {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ - {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ - {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ - {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ - {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ - {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ - {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ - {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ - {DPM_EMU16, (M3)}, /* gpio_27 */ - {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ - {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ - {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ -}; - -const struct pad_conf_entry wkup_padconf_array[] = { - {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ - {PAD1_SIM_CLK, (M0)}, /* sim_clk */ - {PAD0_SIM_RESET, (M0)}, /* sim_reset */ - {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ - {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ - {PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */ - {PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */ - {PAD1_FREF_XTAL_IN, (M0)}, /* # */ - {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ - {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ - {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ - {PAD1_FREF_CLK3_REQ, (M3)}, /* gpio_wk30 */ - {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */ - {PAD1_FREF_CLK4_REQ, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* led status_1 */ - {PAD0_FREF_CLK4_OUT, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* led status_2 */ - {PAD1_SYS_32K, (IEN | M0)}, /* sys_32k */ - {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ - {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ - {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ - {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ - {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ - {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ -}; - -#endif diff --git a/board/ti/panda/panda_mux_data.h b/board/ti/panda/panda_mux_data.h new file mode 100644 index 00000000000..16cc0ad6e02 --- /dev/null +++ b/board/ti/panda/panda_mux_data.h @@ -0,0 +1,230 @@ +/* + * (C) Copyright 2010 + * Texas Instruments Incorporated, + * + * Balaji Krishnamoorthy + * Aneesh V + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _SDP4430_MUX_DATA_H +#define _SDP4430_MUX_DATA_H + +#include + +const struct pad_conf_entry core_padconf_array_non_essential[] = { + {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ + {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ + {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ + {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ + {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ + {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ + {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ + {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ + {GPMC_A16, (M3)}, /* gpio_40 */ + {GPMC_A17, (PTD | M3)}, /* gpio_41 */ + {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ + {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ + {GPMC_A20, (IEN | M3)}, /* gpio_44 */ + {GPMC_A21, (M3)}, /* gpio_45 */ + {GPMC_A22, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col6 */ + {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ + {GPMC_A24, (PTD | M3)}, /* gpio_48 */ + {GPMC_A25, (PTD | M3)}, /* gpio_49 */ + {GPMC_NCS0, (M3)}, /* gpio_50 */ + {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ + {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ + {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ + {GPMC_NWP, (M3)}, /* gpio_54 */ + {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ + {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ + {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ + {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ + {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ + {GPMC_WAIT1, (IEN | M3)}, /* gpio_62 */ + {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ + {C2C_DATA12, (M1)}, /* dsi1_te0 */ + {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ + {C2C_DATA14, (M1)}, /* dsi2_te0 */ + {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ + {HDMI_HPD, (M0)}, /* hdmi_hpd */ + {HDMI_CEC, (M0)}, /* hdmi_cec */ + {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ + {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ + {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ + {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ + {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ + {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ + {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ + {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ + {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ + {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ + {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ + {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ + {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ + {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ + {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ + {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ + {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ + {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ + {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ + {USBB1_ULPITLL_CLK, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cawake */ + {USBB1_ULPITLL_STP, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cadata */ + {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caflag */ + {USBB1_ULPITLL_NXT, (OFF_EN | M1)}, /* hsi1_acready */ + {USBB1_ULPITLL_DAT0, (OFF_EN | M1)}, /* hsi1_acwake */ + {USBB1_ULPITLL_DAT1, (OFF_EN | M1)}, /* hsi1_acdata */ + {USBB1_ULPITLL_DAT2, (OFF_EN | M1)}, /* hsi1_acflag */ + {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caready */ + {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */ + {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */ + {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */ + {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */ + {USBB1_HSIC_DATA, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_data */ + {USBB1_HSIC_STROBE, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_strobe */ + {USBC1_ICUSB_DP, (IEN | M0)}, /* usbc1_icusb_dp */ + {USBC1_ICUSB_DM, (IEN | M0)}, /* usbc1_icusb_dm */ + {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ + {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ + {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ + {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ + {ABE_MCBSP1_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_clkx */ + {ABE_MCBSP1_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dr */ + {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ + {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ + {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ + {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ + {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ + {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ + {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ + {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ + {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ + {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */ + {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ + {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */ + {UART2_RTS, (M0)}, /* uart2_rts */ + {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */ + {UART2_TX, (M0)}, /* uart2_tx */ + {HDQ_SIO, (M3)}, /* gpio_127 */ + {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ + {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ + {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ + {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ + {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ + {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ + {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ + {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ + {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ + {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ + {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ + {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ + {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ + {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ + {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ + {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ + {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ + {UART4_RX, (IEN | M0)}, /* uart4_rx */ + {UART4_TX, (M0)}, /* uart4_tx */ + {USBB2_ULPITLL_CLK, (PTD | IEN | M3)}, /* gpio_157 */ + {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ + {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ + {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ + {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ + {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ + {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ + {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ + {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ + {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ + {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ + {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ + {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ + {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ + {UNIPRO_TX0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col0 */ + {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ + {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ + {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ + {UNIPRO_TX2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col4 */ + {UNIPRO_TY2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col5 */ + {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ + {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ + {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ + {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ + {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ + {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ + {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */ + {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */ + {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */ + {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ + {FREF_CLK2_OUT, (M0)}, /* fref_clk2_out */ + {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ + {SYS_NIRQ2, (M7)}, /* sys_nirq2 */ + {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ + {SYS_BOOT1, (M3)}, /* gpio_185 */ + {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ + {SYS_BOOT3, (PTD | IEN | M3)}, /* gpio_187 */ + {SYS_BOOT4, (M3)}, /* gpio_188 */ + {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ + {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ + {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ + {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ + {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ + {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ + {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ + {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ + {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ + {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ + {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ + {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ + {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ + {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ + {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ + {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ + {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ + {DPM_EMU16, (M3)}, /* gpio_27 */ + {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ + {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ + {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ +}; + +const struct pad_conf_entry wkup_padconf_array_non_essential[] = { + {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ + {PAD1_SIM_CLK, (M0)}, /* sim_clk */ + {PAD0_SIM_RESET, (M0)}, /* sim_reset */ + {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ + {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ + {PAD1_FREF_XTAL_IN, (M0)}, /* # */ + {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ + {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ + {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ + {PAD1_FREF_CLK3_REQ, (PTU | IEN | M0)}, /* # */ + {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */ + {PAD1_FREF_CLK4_REQ, (PTU | IEN | M0)}, /* # */ + {PAD0_FREF_CLK4_OUT, (M0)}, /* # */ + {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ + {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ + {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ + {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ + {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ + {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ + {PAD1_FREF_CLK3_REQ, (M3)}, /* gpio_wk30 */ + {PAD1_FREF_CLK4_REQ, (M3)}, /* gpio_wk7 */ + {PAD0_FREF_CLK4_OUT, (M3)}, /* gpio_wk8 */ +}; + +#endif /* _SDP4430_MUX_DATA_H */ diff --git a/board/ti/sdp4430/sdp.c b/board/ti/sdp4430/sdp.c index b13c4c5c1d8..a5ea6829cd2 100644 --- a/board/ti/sdp4430/sdp.c +++ b/board/ti/sdp4430/sdp.c @@ -27,7 +27,7 @@ #include #include -#include "sdp.h" +#include "sdp4430_mux_data.h" DECLARE_GLOBAL_DATA_PTR; @@ -70,27 +70,14 @@ int misc_init_r(void) return 0; } -void do_set_mux(u32 base, struct pad_conf_entry const *array, int size) +void set_muxconf_regs_non_essential(void) { - int i; - struct pad_conf_entry *pad = (struct pad_conf_entry *) array; - - for (i = 0; i < size; i++, pad++) - writew(pad->val, base + pad->offset); -} - -/** - * @brief set_muxconf_regs Setting up the configuration Mux registers - * specific to the board. - */ -void set_muxconf_regs(void) -{ - do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array, - sizeof(core_padconf_array) / + do_set_mux(CONTROL_PADCONF_CORE, core_padconf_array_non_essential, + sizeof(core_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); - do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array, - sizeof(wkup_padconf_array) / + do_set_mux(CONTROL_PADCONF_WKUP, wkup_padconf_array_non_essential, + sizeof(wkup_padconf_array_non_essential) / sizeof(struct pad_conf_entry)); } diff --git a/board/ti/sdp4430/sdp.h b/board/ti/sdp4430/sdp.h deleted file mode 100644 index bf41067ca71..00000000000 --- a/board/ti/sdp4430/sdp.h +++ /dev/null @@ -1,264 +0,0 @@ -/* - * (C) Copyright 2010 - * Texas Instruments Incorporated, - * - * Balaji Krishnamoorthy - * Aneesh V - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef _SDP_H_ -#define _SDP_H_ - -#include -#include - -const struct pad_conf_entry core_padconf_array[] = { - {GPMC_AD0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat0 */ - {GPMC_AD1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat1 */ - {GPMC_AD2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat2 */ - {GPMC_AD3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat3 */ - {GPMC_AD4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat4 */ - {GPMC_AD5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat5 */ - {GPMC_AD6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat6 */ - {GPMC_AD7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_dat7 */ - {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ - {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ - {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ - {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ - {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ - {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ - {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ - {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ - {GPMC_A16, (M3)}, /* gpio_40 */ - {GPMC_A17, (PTD | M3)}, /* gpio_41 */ - {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ - {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ - {GPMC_A20, (IEN | M3)}, /* gpio_44 */ - {GPMC_A21, (M3)}, /* gpio_45 */ - {GPMC_A22, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col6 */ - {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ - {GPMC_A24, (PTD | M3)}, /* gpio_48 */ - {GPMC_A25, (PTD | M3)}, /* gpio_49 */ - {GPMC_NCS0, (M3)}, /* gpio_50 */ - {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ - {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ - {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ - {GPMC_NWP, (M3)}, /* gpio_54 */ - {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ - {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ - {GPMC_NOE, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M1)}, /* sdmmc2_clk */ - {GPMC_NWE, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* sdmmc2_cmd */ - {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ - {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ - {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ - {GPMC_WAIT1, (IEN | M3)}, /* gpio_62 */ - {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ - {C2C_DATA12, (M1)}, /* dsi1_te0 */ - {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ - {C2C_DATA14, (M1)}, /* dsi2_te0 */ - {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ - {HDMI_HPD, (M0)}, /* hdmi_hpd */ - {HDMI_CEC, (M0)}, /* hdmi_cec */ - {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ - {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ - {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ - {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ - {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ - {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ - {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ - {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ - {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ - {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ - {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ - {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ - {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ - {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ - {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ - {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ - {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ - {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ - {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ - {USBB1_ULPITLL_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M4)},/* usbb1_ulpiphy_clk */ - {USBB1_ULPITLL_STP, (OFF_EN | OFF_OUT_PTD | M4)}, /* usbb1_ulpiphy_stp */ - {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dir */ - {USBB1_ULPITLL_NXT, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_nxt */ - {USBB1_ULPITLL_DAT0, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat0 */ - {USBB1_ULPITLL_DAT1, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat1 */ - {USBB1_ULPITLL_DAT2, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat2 */ - {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat3 */ - {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */ - {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */ - {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */ - {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */ - {USBB1_HSIC_DATA, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_data */ - {USBB1_HSIC_STROBE, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_strobe */ - {USBC1_ICUSB_DP, (IEN | M0)}, /* usbc1_icusb_dp */ - {USBC1_ICUSB_DM, (IEN | M0)}, /* usbc1_icusb_dm */ - {SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */ - {SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */ - {SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */ - {SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */ - {SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */ - {SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */ - {SDMMC1_DAT4, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat4 */ - {SDMMC1_DAT5, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat5 */ - {SDMMC1_DAT6, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat6 */ - {SDMMC1_DAT7, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat7 */ - {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ - {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ - {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ - {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ - {ABE_MCBSP1_CLKX, (IEN | M1)}, /* abe_slimbus1_clock */ - {ABE_MCBSP1_DR, (IEN | M1)}, /* abe_slimbus1_data */ - {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ - {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ - {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ - {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ - {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ - {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ - {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ - {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ - {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ - {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */ - {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ - {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */ - {UART2_RTS, (M0)}, /* uart2_rts */ - {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */ - {UART2_TX, (M0)}, /* uart2_tx */ - {HDQ_SIO, (M3)}, /* gpio_127 */ - {I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */ - {I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */ - {I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */ - {I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */ - {I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */ - {I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */ - {I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */ - {I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */ - {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ - {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ - {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ - {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ - {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ - {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ - {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ - {UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */ - {UART3_RTS_SD, (M0)}, /* uart3_rts_sd */ - {UART3_RX_IRRX, (IEN | M0)}, /* uart3_rx */ - {UART3_TX_IRTX, (M0)}, /* uart3_tx */ - {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ - {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ - {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ - {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ - {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ - {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ - {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ - {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ - {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ - {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ - {UART4_RX, (IEN | M0)}, /* uart4_rx */ - {UART4_TX, (M0)}, /* uart4_tx */ - {USBB2_ULPITLL_CLK, (IEN | M3)}, /* gpio_157 */ - {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ - {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ - {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ - {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ - {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ - {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ - {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ - {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ - {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ - {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ - {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ - {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ - {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ - {UNIPRO_TX0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col0 */ - {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ - {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ - {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ - {UNIPRO_TX2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col4 */ - {UNIPRO_TY2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col5 */ - {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ - {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ - {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ - {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ - {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ - {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ - {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */ - {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */ - {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */ - {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ - {FREF_CLK2_OUT, (M0)}, /* fref_clk2_out */ - {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ - {SYS_NIRQ2, (PTU | IEN | M0)}, /* sys_nirq2 */ - {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ - {SYS_BOOT1, (M3)}, /* gpio_185 */ - {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ - {SYS_BOOT3, (M3)}, /* gpio_187 */ - {SYS_BOOT4, (M3)}, /* gpio_188 */ - {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ - {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ - {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ - {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ - {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ - {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ - {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ - {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ - {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ - {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ - {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ - {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ - {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ - {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ - {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ - {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ - {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ - {DPM_EMU16, (M3)}, /* gpio_27 */ - {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ - {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ - {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ -}; - -const struct pad_conf_entry wkup_padconf_array[] = { - {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ - {PAD1_SIM_CLK, (M0)}, /* sim_clk */ - {PAD0_SIM_RESET, (M0)}, /* sim_reset */ - {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ - {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ - {PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */ - {PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */ - {PAD1_FREF_XTAL_IN, (M0)}, /* # */ - {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ - {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ - {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ - {PAD1_FREF_CLK3_REQ, (PTU | IEN | M0)}, /* # */ - {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */ - {PAD1_FREF_CLK4_REQ, (PTU | IEN | M0)}, /* # */ - {PAD0_FREF_CLK4_OUT, (M0)}, /* # */ - {PAD1_SYS_32K, (IEN | M0)}, /* sys_32k */ - {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ - {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ - {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ - {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ - {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ - {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ -}; - -#endif diff --git a/board/ti/sdp4430/sdp4430_mux_data.h b/board/ti/sdp4430/sdp4430_mux_data.h new file mode 100644 index 00000000000..16cc0ad6e02 --- /dev/null +++ b/board/ti/sdp4430/sdp4430_mux_data.h @@ -0,0 +1,230 @@ +/* + * (C) Copyright 2010 + * Texas Instruments Incorporated, + * + * Balaji Krishnamoorthy + * Aneesh V + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef _SDP4430_MUX_DATA_H +#define _SDP4430_MUX_DATA_H + +#include + +const struct pad_conf_entry core_padconf_array_non_essential[] = { + {GPMC_AD8, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* gpio_32 */ + {GPMC_AD9, (PTU | IEN | M3)}, /* gpio_33 */ + {GPMC_AD10, (PTU | IEN | M3)}, /* gpio_34 */ + {GPMC_AD11, (PTU | IEN | M3)}, /* gpio_35 */ + {GPMC_AD12, (PTU | IEN | M3)}, /* gpio_36 */ + {GPMC_AD13, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_37 */ + {GPMC_AD14, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_38 */ + {GPMC_AD15, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_39 */ + {GPMC_A16, (M3)}, /* gpio_40 */ + {GPMC_A17, (PTD | M3)}, /* gpio_41 */ + {GPMC_A18, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row6 */ + {GPMC_A19, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row7 */ + {GPMC_A20, (IEN | M3)}, /* gpio_44 */ + {GPMC_A21, (M3)}, /* gpio_45 */ + {GPMC_A22, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col6 */ + {GPMC_A23, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col7 */ + {GPMC_A24, (PTD | M3)}, /* gpio_48 */ + {GPMC_A25, (PTD | M3)}, /* gpio_49 */ + {GPMC_NCS0, (M3)}, /* gpio_50 */ + {GPMC_NCS1, (IEN | M3)}, /* gpio_51 */ + {GPMC_NCS2, (IEN | M3)}, /* gpio_52 */ + {GPMC_NCS3, (IEN | M3)}, /* gpio_53 */ + {GPMC_NWP, (M3)}, /* gpio_54 */ + {GPMC_CLK, (PTD | M3)}, /* gpio_55 */ + {GPMC_NADV_ALE, (M3)}, /* gpio_56 */ + {GPMC_NBE0_CLE, (M3)}, /* gpio_59 */ + {GPMC_NBE1, (PTD | M3)}, /* gpio_60 */ + {GPMC_WAIT0, (PTU | IEN | M3)}, /* gpio_61 */ + {GPMC_WAIT1, (IEN | M3)}, /* gpio_62 */ + {C2C_DATA11, (PTD | M3)}, /* gpio_100 */ + {C2C_DATA12, (M1)}, /* dsi1_te0 */ + {C2C_DATA13, (PTD | M3)}, /* gpio_102 */ + {C2C_DATA14, (M1)}, /* dsi2_te0 */ + {C2C_DATA15, (PTD | M3)}, /* gpio_104 */ + {HDMI_HPD, (M0)}, /* hdmi_hpd */ + {HDMI_CEC, (M0)}, /* hdmi_cec */ + {HDMI_DDC_SCL, (PTU | M0)}, /* hdmi_ddc_scl */ + {HDMI_DDC_SDA, (PTU | IEN | M0)}, /* hdmi_ddc_sda */ + {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */ + {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */ + {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */ + {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */ + {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */ + {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */ + {CSI21_DX3, (PTD | M7)}, /* csi21_dx3 */ + {CSI21_DY3, (PTD | M7)}, /* csi21_dy3 */ + {CSI21_DX4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dx4 */ + {CSI21_DY4, (PTD | OFF_EN | OFF_PD | OFF_IN | M7)}, /* csi21_dy4 */ + {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */ + {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */ + {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */ + {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */ + {CAM_SHUTTER, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_shutter */ + {CAM_STROBE, (OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* cam_strobe */ + {CAM_GLOBALRESET, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M3)}, /* gpio_83 */ + {USBB1_ULPITLL_CLK, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cawake */ + {USBB1_ULPITLL_STP, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_cadata */ + {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caflag */ + {USBB1_ULPITLL_NXT, (OFF_EN | M1)}, /* hsi1_acready */ + {USBB1_ULPITLL_DAT0, (OFF_EN | M1)}, /* hsi1_acwake */ + {USBB1_ULPITLL_DAT1, (OFF_EN | M1)}, /* hsi1_acdata */ + {USBB1_ULPITLL_DAT2, (OFF_EN | M1)}, /* hsi1_acflag */ + {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_IN | M1)}, /* hsi1_caready */ + {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */ + {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */ + {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */ + {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */ + {USBB1_HSIC_DATA, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_data */ + {USBB1_HSIC_STROBE, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usbb1_hsic_strobe */ + {USBC1_ICUSB_DP, (IEN | M0)}, /* usbc1_icusb_dp */ + {USBC1_ICUSB_DM, (IEN | M0)}, /* usbc1_icusb_dm */ + {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */ + {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */ + {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */ + {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */ + {ABE_MCBSP1_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_clkx */ + {ABE_MCBSP1_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dr */ + {ABE_MCBSP1_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp1_dx */ + {ABE_MCBSP1_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp1_fsx */ + {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */ + {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */ + {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */ + {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */ + {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */ + {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */ + {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */ + {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */ + {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */ + {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */ + {UART2_RTS, (M0)}, /* uart2_rts */ + {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */ + {UART2_TX, (M0)}, /* uart2_tx */ + {HDQ_SIO, (M3)}, /* gpio_127 */ + {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */ + {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */ + {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */ + {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */ + {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M3)}, /* mcspi1_cs1 */ + {MCSPI1_CS2, (PTU | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_139 */ + {MCSPI1_CS3, (PTU | IEN | M3)}, /* gpio_140 */ + {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc5_clk */ + {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */ + {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */ + {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */ + {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */ + {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */ + {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */ + {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */ + {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */ + {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */ + {UART4_RX, (IEN | M0)}, /* uart4_rx */ + {UART4_TX, (M0)}, /* uart4_tx */ + {USBB2_ULPITLL_CLK, (PTD | IEN | M3)}, /* gpio_157 */ + {USBB2_ULPITLL_STP, (IEN | M5)}, /* dispc2_data23 */ + {USBB2_ULPITLL_DIR, (IEN | M5)}, /* dispc2_data22 */ + {USBB2_ULPITLL_NXT, (IEN | M5)}, /* dispc2_data21 */ + {USBB2_ULPITLL_DAT0, (IEN | M5)}, /* dispc2_data20 */ + {USBB2_ULPITLL_DAT1, (IEN | M5)}, /* dispc2_data19 */ + {USBB2_ULPITLL_DAT2, (IEN | M5)}, /* dispc2_data18 */ + {USBB2_ULPITLL_DAT3, (IEN | M5)}, /* dispc2_data15 */ + {USBB2_ULPITLL_DAT4, (IEN | M5)}, /* dispc2_data14 */ + {USBB2_ULPITLL_DAT5, (IEN | M5)}, /* dispc2_data13 */ + {USBB2_ULPITLL_DAT6, (IEN | M5)}, /* dispc2_data12 */ + {USBB2_ULPITLL_DAT7, (IEN | M5)}, /* dispc2_data11 */ + {USBB2_HSIC_DATA, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_169 */ + {USBB2_HSIC_STROBE, (PTD | OFF_EN | OFF_OUT_PTU | M3)}, /* gpio_170 */ + {UNIPRO_TX0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col0 */ + {UNIPRO_TY0, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col1 */ + {UNIPRO_TX1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col2 */ + {UNIPRO_TY1, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col3 */ + {UNIPRO_TX2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col4 */ + {UNIPRO_TY2, (OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_col5 */ + {UNIPRO_RX0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row0 */ + {UNIPRO_RY0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row1 */ + {UNIPRO_RX1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row2 */ + {UNIPRO_RY1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row3 */ + {UNIPRO_RX2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row4 */ + {UNIPRO_RY2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M1)}, /* kpd_row5 */ + {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */ + {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */ + {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */ + {FREF_CLK1_OUT, (M0)}, /* fref_clk1_out */ + {FREF_CLK2_OUT, (M0)}, /* fref_clk2_out */ + {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */ + {SYS_NIRQ2, (M7)}, /* sys_nirq2 */ + {SYS_BOOT0, (PTU | IEN | M3)}, /* gpio_184 */ + {SYS_BOOT1, (M3)}, /* gpio_185 */ + {SYS_BOOT2, (PTD | IEN | M3)}, /* gpio_186 */ + {SYS_BOOT3, (PTD | IEN | M3)}, /* gpio_187 */ + {SYS_BOOT4, (M3)}, /* gpio_188 */ + {SYS_BOOT5, (PTD | IEN | M3)}, /* gpio_189 */ + {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */ + {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */ + {DPM_EMU2, (IEN | M0)}, /* dpm_emu2 */ + {DPM_EMU3, (IEN | M5)}, /* dispc2_data10 */ + {DPM_EMU4, (IEN | M5)}, /* dispc2_data9 */ + {DPM_EMU5, (IEN | M5)}, /* dispc2_data16 */ + {DPM_EMU6, (IEN | M5)}, /* dispc2_data17 */ + {DPM_EMU7, (IEN | M5)}, /* dispc2_hsync */ + {DPM_EMU8, (IEN | M5)}, /* dispc2_pclk */ + {DPM_EMU9, (IEN | M5)}, /* dispc2_vsync */ + {DPM_EMU10, (IEN | M5)}, /* dispc2_de */ + {DPM_EMU11, (IEN | M5)}, /* dispc2_data8 */ + {DPM_EMU12, (IEN | M5)}, /* dispc2_data7 */ + {DPM_EMU13, (IEN | M5)}, /* dispc2_data6 */ + {DPM_EMU14, (IEN | M5)}, /* dispc2_data5 */ + {DPM_EMU15, (IEN | M5)}, /* dispc2_data4 */ + {DPM_EMU16, (M3)}, /* gpio_27 */ + {DPM_EMU17, (IEN | M5)}, /* dispc2_data2 */ + {DPM_EMU18, (IEN | M5)}, /* dispc2_data1 */ + {DPM_EMU19, (IEN | M5)}, /* dispc2_data0 */ +}; + +const struct pad_conf_entry wkup_padconf_array_non_essential[] = { + {PAD0_SIM_IO, (IEN | M0)}, /* sim_io */ + {PAD1_SIM_CLK, (M0)}, /* sim_clk */ + {PAD0_SIM_RESET, (M0)}, /* sim_reset */ + {PAD1_SIM_CD, (PTU | IEN | M0)}, /* sim_cd */ + {PAD0_SIM_PWRCTRL, (M0)}, /* sim_pwrctrl */ + {PAD1_FREF_XTAL_IN, (M0)}, /* # */ + {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */ + {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */ + {PAD0_FREF_CLK0_OUT, (M2)}, /* sys_drm_msecure */ + {PAD1_FREF_CLK3_REQ, (PTU | IEN | M0)}, /* # */ + {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */ + {PAD1_FREF_CLK4_REQ, (PTU | IEN | M0)}, /* # */ + {PAD0_FREF_CLK4_OUT, (M0)}, /* # */ + {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */ + {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */ + {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */ + {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */ + {PAD0_SYS_BOOT6, (IEN | M3)}, /* gpio_wk9 */ + {PAD1_SYS_BOOT7, (IEN | M3)}, /* gpio_wk10 */ + {PAD1_FREF_CLK3_REQ, (M3)}, /* gpio_wk30 */ + {PAD1_FREF_CLK4_REQ, (M3)}, /* gpio_wk7 */ + {PAD0_FREF_CLK4_OUT, (M3)}, /* gpio_wk8 */ +}; + +#endif /* _SDP4430_MUX_DATA_H */ -- cgit v1.3.1 From bcae72116257201d7288cb8c525a29aea4875b95 Mon Sep 17 00:00:00 2001 From: Aneesh V Date: Thu, 21 Jul 2011 09:10:21 -0400 Subject: omap: add basic SPL support - Provide alternate implementations of board_init_f() board_init_r() for OMAP spl. - Provide linker script - Initialize global data - Add serial console support - Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move it to board config header from config.mk Signed-off-by: Aneesh V Signed-off-by: Sandeep Paulraj --- arch/arm/cpu/armv7/Makefile | 7 ++- arch/arm/cpu/armv7/omap-common/Makefile | 4 ++ arch/arm/cpu/armv7/omap-common/spl.c | 82 +++++++++++++++++++++++++++ arch/arm/cpu/armv7/omap-common/u-boot-spl.lds | 62 ++++++++++++++++++++ arch/arm/cpu/armv7/omap4/Makefile | 5 +- arch/arm/cpu/armv7/omap4/board.c | 7 +++ arch/arm/cpu/armv7/omap4/clocks.c | 33 +++++++++++ arch/arm/include/asm/arch-omap4/sys_proto.h | 1 + arch/arm/include/asm/omap_common.h | 2 + board/ti/panda/Makefile | 2 + board/ti/panda/config.mk | 31 ---------- board/ti/sdp4430/Makefile | 2 + board/ti/sdp4430/config.mk | 31 ---------- include/configs/omap4_panda.h | 26 +++++++++ include/configs/omap4_sdp4430.h | 26 +++++++++ 15 files changed, 257 insertions(+), 64 deletions(-) create mode 100644 arch/arm/cpu/armv7/omap-common/spl.c create mode 100644 arch/arm/cpu/armv7/omap-common/u-boot-spl.lds delete mode 100644 board/ti/panda/config.mk delete mode 100644 board/ti/sdp4430/config.mk (limited to 'board') diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile index 299792ac5a1..92a5a968006 100644 --- a/arch/arm/cpu/armv7/Makefile +++ b/arch/arm/cpu/armv7/Makefile @@ -26,7 +26,12 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(CPU).o START := start.o -COBJS := cpu.o cache_v7.o + +ifndef CONFIG_SPL_BUILD +COBJS += cache_v7.o +COBJS += cpu.o +endif + COBJS += syslib.o SRCS := $(START:.o=.S) $(COBJS:.o=.c) diff --git a/arch/arm/cpu/armv7/omap-common/Makefile b/arch/arm/cpu/armv7/omap-common/Makefile index 8f698f841df..07087964e6a 100644 --- a/arch/arm/cpu/armv7/omap-common/Makefile +++ b/arch/arm/cpu/armv7/omap-common/Makefile @@ -30,6 +30,10 @@ SOBJS := reset.o COBJS := timer.o COBJS += utils.o +ifdef CONFIG_SPL_BUILD +COBJS += spl.o +endif + SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/arch/arm/cpu/armv7/omap-common/spl.c b/arch/arm/cpu/armv7/omap-common/spl.c new file mode 100644 index 00000000000..b2015431e32 --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/spl.c @@ -0,0 +1,82 @@ +/* + * (C) Copyright 2010 + * Texas Instruments, + * + * Aneesh V + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +/* Define global data structure pointer to it*/ +static gd_t gdata __attribute__ ((section(".data"))); +static bd_t bdata __attribute__ ((section(".data"))); + +inline void hang(void) +{ + puts("### ERROR ### Please RESET the board ###\n"); + for (;;) + ; +} + +void board_init_f(ulong dummy) +{ + /* + * We call relocate_code() with relocation target same as the + * CONFIG_SYS_SPL_TEXT_BASE. This will result in relocation getting + * skipped. Instead, only .bss initialization will happen. That's + * all we need + */ + debug(">>board_init_f()\n"); + relocate_code(CONFIG_SPL_STACK, &gdata, CONFIG_SPL_TEXT_BASE); +} + +void board_init_r(gd_t *id, ulong dummy) +{ + for (;;) + ; +} + +void preloader_console_init(void) +{ + const char *u_boot_rev = U_BOOT_VERSION; + char rev_string_buffer[50]; + + gd = &gdata; + gd->bd = &bdata; + gd->flags |= GD_FLG_RELOC; + gd->baudrate = CONFIG_BAUDRATE; + + setup_clocks_for_console(); + serial_init(); /* serial communications setup */ + + /* Avoid a second "U-Boot" coming from this string */ + u_boot_rev = &u_boot_rev[7]; + + printf("\nU-Boot SPL %s (%s - %s)\n", u_boot_rev, U_BOOT_DATE, + U_BOOT_TIME); + omap_rev_string(rev_string_buffer); + printf("Texas Instruments %s\n", rev_string_buffer); +} diff --git a/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds new file mode 100644 index 00000000000..8867e0604db --- /dev/null +++ b/arch/arm/cpu/armv7/omap-common/u-boot-spl.lds @@ -0,0 +1,62 @@ +/* + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * (C) Copyright 2010 + * Texas Instruments, + * Aneesh V + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\ + LENGTH = CONFIG_SPL_MAX_SIZE } +MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \ + LENGTH = CONFIG_SPL_BSS_MAX_SIZE } + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + .text : + { + __start = .; + arch/arm/cpu/armv7/start.o (.text) + *(.text*) + } >.sram + + . = ALIGN(4); + .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram + + . = ALIGN(4); + .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram + . = ALIGN(4); + __image_copy_end = .; + _end = .; + + .bss : + { + . = ALIGN(4); + __bss_start = .; + *(.bss*) + . = ALIGN(4); + __bss_end__ = .; + } >.sdram +} diff --git a/arch/arm/cpu/armv7/omap4/Makefile b/arch/arm/cpu/armv7/omap4/Makefile index e1ccd68192b..e7ee0b8c0ab 100644 --- a/arch/arm/cpu/armv7/omap4/Makefile +++ b/arch/arm/cpu/armv7/omap4/Makefile @@ -30,9 +30,12 @@ SOBJS += lowlevel_init.o COBJS += board.o COBJS += clocks.o COBJS += emif.o -COBJS += mem.o COBJS += sdram_elpida.o + +ifndef CONFIG_SPL_BUILD +COBJS += mem.o COBJS += sys_info.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS)) diff --git a/arch/arm/cpu/armv7/omap4/board.c b/arch/arm/cpu/armv7/omap4/board.c index 786c239794d..54dd5091947 100644 --- a/arch/arm/cpu/armv7/omap4/board.c +++ b/arch/arm/cpu/armv7/omap4/board.c @@ -155,7 +155,14 @@ void s_init(void) init_omap4_revision(); watchdog_init(); set_mux_conf_regs(); +#ifdef CONFIG_SPL_BUILD + preloader_console_init(); +#endif prcm_init(); +#ifdef CONFIG_SPL_BUILD + /* For regular u-boot sdram_init() is called from dram_init() */ + sdram_init(); +#endif } /* diff --git a/arch/arm/cpu/armv7/omap4/clocks.c b/arch/arm/cpu/armv7/omap4/clocks.c index e8d3a524403..f1e233a10ec 100644 --- a/arch/arm/cpu/armv7/omap4/clocks.c +++ b/arch/arm/cpu/armv7/omap4/clocks.c @@ -791,6 +791,39 @@ void lock_dpll(u32 *const base) wait_for_lock(base); } +void setup_clocks_for_console(void) +{ + /* Do not add any spl_debug prints in this function */ + clrsetbits_le32(&prcm->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_SW_WKUP << + CD_CLKCTRL_CLKTRCTRL_SHIFT); + + /* Enable all UARTs - console will be on one of them */ + clrsetbits_le32(&prcm->cm_l4per_uart1_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart2_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart3_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_uart3_clkctrl, + MODULE_CLKCTRL_MODULEMODE_MASK, + MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN << + MODULE_CLKCTRL_MODULEMODE_SHIFT); + + clrsetbits_le32(&prcm->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK, + CD_CLKCTRL_CLKTRCTRL_HW_AUTO << + CD_CLKCTRL_CLKTRCTRL_SHIFT); +} + void prcm_init(void) { switch (omap4_hw_init_context()) { diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index 1e62878ea47..a81f8e5c240 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -44,6 +44,7 @@ u32 wait_on_value(u32, u32, void *, u32); void sdelay(unsigned long); void set_pl310_ctrl_reg(u32 val); void omap_rev_string(char *omap4_rev_string); +void setup_clocks_for_console(void); void prcm_init(void); void bypass_dpll(u32 *const base); void freq_update_core(void); diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index 33caa4e6cc8..69d53d2c729 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -34,4 +34,6 @@ #define OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL 2 #define OMAP_INIT_CONTEXT_UBOOT_AFTER_CH 3 +void preloader_console_init(void); + #endif /* _OMAP_COMMON_H_ */ diff --git a/board/ti/panda/Makefile b/board/ti/panda/Makefile index 21864037327..09f88ee86d6 100644 --- a/board/ti/panda/Makefile +++ b/board/ti/panda/Makefile @@ -25,7 +25,9 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +ifndef CONFIG_SPL_BUILD COBJS := panda.o +endif SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/ti/panda/config.mk b/board/ti/panda/config.mk deleted file mode 100644 index 33901a77b56..00000000000 --- a/board/ti/panda/config.mk +++ /dev/null @@ -1,31 +0,0 @@ -# -# (C) Copyright 2006-2009 -# Texas Instruments Incorporated, -# -# OMAP 4430 SDP -# see http://www.ti.com/ for more information on Texas Instruments -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# SDRAM Address Space: -# 8000'0000 - 9fff'ffff (512 MB) -# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 -# (mem base + reserved) - -CONFIG_SYS_TEXT_BASE = 0x80e80000 diff --git a/board/ti/sdp4430/Makefile b/board/ti/sdp4430/Makefile index f1ee5448eda..12f2743d493 100644 --- a/board/ti/sdp4430/Makefile +++ b/board/ti/sdp4430/Makefile @@ -25,7 +25,9 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +ifndef CONFIG_SPL_BUILD COBJS := sdp.o cmd_bat.o +endif SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/ti/sdp4430/config.mk b/board/ti/sdp4430/config.mk deleted file mode 100644 index 33901a77b56..00000000000 --- a/board/ti/sdp4430/config.mk +++ /dev/null @@ -1,31 +0,0 @@ -# -# (C) Copyright 2006-2009 -# Texas Instruments Incorporated, -# -# OMAP 4430 SDP -# see http://www.ti.com/ for more information on Texas Instruments -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# -# SDRAM Address Space: -# 8000'0000 - 9fff'ffff (512 MB) -# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 -# (mem base + reserved) - -CONFIG_SYS_TEXT_BASE = 0x80e80000 diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h index a8dd8611266..1112362b323 100644 --- a/include/configs/omap4_panda.h +++ b/include/configs/omap4_panda.h @@ -243,4 +243,30 @@ #define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS #endif +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_TEXT_BASE 0x40304350 +#define CONFIG_SPL_MAX_SIZE 0x8000 /* 32 K */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds" + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80100000 + #endif /* __CONFIG_H */ diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h index 534f89a5e72..6a6be9e9b85 100644 --- a/include/configs/omap4_sdp4430.h +++ b/include/configs/omap4_sdp4430.h @@ -249,4 +249,30 @@ #define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS #endif +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_TEXT_BASE 0x40304350 +#define CONFIG_SPL_MAX_SIZE 0x8000 /* 32 K */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds" + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80100000 + #endif /* __CONFIG_H */ -- cgit v1.3.1 From 21d671d0c492984c75c7cb704325e56448bf277a Mon Sep 17 00:00:00 2001 From: "Xu, Hong" Date: Mon, 1 Aug 2011 03:56:53 +0000 Subject: AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master Rework for AT91SAM9RL-EK, makes it build again. Based on the work for AT91SAM9260-EK. V4: added changes to MAKEALL Signed-off-by: Hong Xu Signed-off-by: Reinhard Meyer --- MAKEALL | 1 - Makefile | 12 ----- board/atmel/at91sam9rlek/at91sam9rlek.c | 73 +++++++++++++++++----------- board/atmel/at91sam9rlek/config.mk | 1 - board/atmel/at91sam9rlek/led.c | 6 ++- boards.cfg | 2 + include/configs/at91sam9rlek.h | 85 +++++++++++++++++++-------------- 7 files changed, 99 insertions(+), 81 deletions(-) delete mode 100644 board/atmel/at91sam9rlek/config.mk (limited to 'board') diff --git a/MAKEALL b/MAKEALL index 2f4eeb778dc..dad6bd12efd 100755 --- a/MAKEALL +++ b/MAKEALL @@ -450,7 +450,6 @@ LIST_at91="$(boards_by_soc at91)\ at91sam9g10ek \ at91sam9g20ek \ at91sam9m10g45ek \ - at91sam9rlek \ pm9g45 \ SBC35_A9G20 \ TNY_A9260 \ diff --git a/Makefile b/Makefile index e081c25cf40..54b88043283 100644 --- a/Makefile +++ b/Makefile @@ -844,18 +844,6 @@ at91sam9263ek_config : unconfig fi; @$(MKCONFIG) -n $@ -a at91sam9263ek arm arm926ejs at91sam9263ek atmel at91 -at91sam9rlek_nandflash_config \ -at91sam9rlek_dataflash_config \ -at91sam9rlek_dataflash_cs0_config \ -at91sam9rlek_config : unconfig - @mkdir -p $(obj)include - @if [ "$(findstring _nandflash,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_NANDFLASH 1" >>$(obj)include/config.h ; \ - else \ - echo "#define CONFIG_SYS_USE_DATAFLASH 1" >>$(obj)include/config.h ; \ - fi; - @$(MKCONFIG) -n $@ -a at91sam9rlek arm arm926ejs at91sam9rlek atmel at91 - at91sam9m10g45ek_nandflash_config \ at91sam9m10g45ek_dataflash_config \ at91sam9m10g45ek_dataflash_cs0_config \ diff --git a/board/atmel/at91sam9rlek/at91sam9rlek.c b/board/atmel/at91sam9rlek/at91sam9rlek.c index e3749174681..e5590846417 100644 --- a/board/atmel/at91sam9rlek/at91sam9rlek.c +++ b/board/atmel/at91sam9rlek/at91sam9rlek.c @@ -23,6 +23,7 @@ */ #include +#include #include #include #include @@ -31,7 +32,7 @@ #include #include #include -#include + #include #include #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB) @@ -48,33 +49,37 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_CMD_NAND static void at91sam9rlek_nand_hw_init(void) { + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, - csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; + + writel(csa, &matrix->ebicsa); /* Configure SMC CS3 for NAND/SmartMedia */ - at91_sys_write(AT91_SMC_SETUP(3), - AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), - AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) | - AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), - AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); - at91_sys_write(AT91_SMC_MODE(3), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | #ifdef CONFIG_SYS_NAND_DBW_16 - AT91_SMC_DBW_16 | + AT91_SMC_MODE_DBW_16 | #else /* CONFIG_SYS_NAND_DBW_8 */ - AT91_SMC_DBW_8 | + AT91_SMC_MODE_DBW_8 | #endif - AT91_SMC_TDF_(2)); + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_PIOD); + writel(1 << ATMEL_ID_PIOD, &pmc->pcer); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -102,7 +107,7 @@ vidinfo_t panel_info = { vl_vsync_len: 1, vl_upper_margin:1, vl_lower_margin:0, - mmio: AT91SAM9RL_LCDC_BASE, + mmio: ATMEL_BASE_LCDC, }; void lcd_enable(void) @@ -116,6 +121,8 @@ void lcd_disable(void) } static void at91sam9rlek_lcd_hw_init(void) { + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + at91_set_B_periph(AT91_PIN_PC1, 0); /* LCDPWR */ at91_set_A_periph(AT91_PIN_PC5, 0); /* LCDHSYNC */ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDDOTCK */ @@ -138,9 +145,7 @@ static void at91sam9rlek_lcd_hw_init(void) at91_set_B_periph(AT91_PIN_PC24, 0); /* LCDD22 */ at91_set_B_periph(AT91_PIN_PC25, 0); /* LCDD23 */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_LCDC); - - gd->fb_base = 0; + writel(1 << ATMEL_ID_LCDC, &pmc->pcer); } #ifdef CONFIG_LCD_INFO @@ -157,7 +162,7 @@ void lcd_show_board_info(void) lcd_printf ("(C) 2008 ATMEL Corp\n"); lcd_printf ("at91support@atmel.com\n"); lcd_printf ("%s CPU at %s MHz\n", - CONFIG_SYS_AT91_CPU_NAME, + ATMEL_CPU_NAME, strmhz(temp, get_cpu_clk_rate())); dram_size = 0; @@ -173,6 +178,17 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif +int board_early_init_f(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable clocks for all PIOs */ + writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | + (1 << ATMEL_ID_PIOC) | (1 << ATMEL_ID_PIOD), + &pmc->pcer); + + return 0; +} int board_init(void) { @@ -182,9 +198,9 @@ int board_init(void) /* arch number of AT91SAM9RLEK-Board */ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9RLEK; /* adress of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - at91_serial_hw_init(); + at91_seriald_hw_init(); #ifdef CONFIG_CMD_NAND at91sam9rlek_nand_hw_init(); #endif @@ -199,7 +215,8 @@ int board_init(void) int dram_init(void) { - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; + gd->ram_size = get_ram_size( + (void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); return 0; } diff --git a/board/atmel/at91sam9rlek/config.mk b/board/atmel/at91sam9rlek/config.mk deleted file mode 100644 index e554a450073..00000000000 --- a/board/atmel/at91sam9rlek/config.mk +++ /dev/null @@ -1 +0,0 @@ -CONFIG_SYS_TEXT_BASE = 0x23f00000 diff --git a/board/atmel/at91sam9rlek/led.c b/board/atmel/at91sam9rlek/led.c index 9634cc03e14..987e8c061cc 100644 --- a/board/atmel/at91sam9rlek/led.c +++ b/board/atmel/at91sam9rlek/led.c @@ -26,12 +26,14 @@ #include #include #include -#include +#include void coloured_LED_init(void) { + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + /* Enable clock */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9RL_ID_PIOD); + writel(ATMEL_ID_PIOD, &pmc->pcer); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/boards.cfg b/boards.cfg index 3e79c82d4ec..8a5a618416c 100644 --- a/boards.cfg +++ b/boards.cfg @@ -80,6 +80,8 @@ at91sam9260ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91sam9g20ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH at91sam9g20ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0 at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1 +at91sam9rlek_nandflash arm arm926ejs at91sam9rlek atmel at91 at91sam9rlek:AT91SAM9RL,SYS_USE_NANDFLASH +at91sam9rlek_dataflash arm arm926ejs at91sam9rlek atmel at91 at91sam9rlek:AT91SAM9RL,SYS_USE_DATAFLASH at91sam9xeek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_NANDFLASH at91sam9xeek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS0 at91sam9xeek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9XE,SYS_USE_DATAFLASH_CS1 diff --git a/include/configs/at91sam9rlek.h b/include/configs/at91sam9rlek.h index 8dbd0825b52..3ca09e1438d 100644 --- a/include/configs/at91sam9rlek.h +++ b/include/configs/at91sam9rlek.h @@ -27,33 +27,42 @@ #ifndef __CONFIG_H #define __CONFIG_H -#define CONFIG_AT91_LEGACY +#include + +#define CONFIG_SYS_TEXT_BASE 0x21F00000 /* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */ -#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* main clock xtal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91SAM9RLEK 1 /* It's an AT91SAM9RLEK Board */ -#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ -#define CONFIG_AT91SAM9RL 1 /* It's an Atmel AT91SAM9RL SoC*/ -#define CONFIG_AT91SAM9RLEK 1 /* on an AT91SAM9RLEK Board */ #define CONFIG_ARCH_CPU_INIT -#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 -#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_ATMEL_LEGACY +#define CONFIG_AT91_GPIO 1 +#define CONFIG_AT91_GPIO_PULLUP 1 /* * Hardware drivers */ -#define CONFIG_AT91_GPIO 1 -#define CONFIG_ATMEL_USART 1 -#undef CONFIG_USART0 -#undef CONFIG_USART1 -#undef CONFIG_USART2 -#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200, 19200, 38400, 57600, 9600} /* LCD */ #define CONFIG_LCD 1 @@ -62,10 +71,13 @@ #undef LCD_TEST_PATTERN #define CONFIG_LCD_INFO 1 #define CONFIG_LCD_INFO_BELOW_LOGO 1 -#define CONFIG_SYS_WHITE_ON_BLACK 1 +#define CONFIG_SYS_WHITE_ON_BLACK 1 #define CONFIG_ATMEL_LCD 1 #define CONFIG_ATMEL_LCD_RGB565 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Let board_init_f handle the framebuffer allocation */ +#undef CONFIG_FB_ADDR +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 + /* LED */ #define CONFIG_AT91_LED @@ -85,25 +97,29 @@ #undef CONFIG_CMD_IMLS #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS #undef CONFIG_CMD_SOURCE #undef CONFIG_CMD_USB -#define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_NAND 1 /* SDRAM */ #define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM 0x20000000 -#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE 0x04000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE) /* DataFlash */ #define CONFIG_ATMEL_DATAFLASH_SPI -#define CONFIG_HAS_DATAFLASH 1 +#define CONFIG_HAS_DATAFLASH 1 #define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ) #define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ -#define AT91_SPI_CLK 15000000 -#define DATAFLASH_TCSS (0x1a << 16) -#define DATAFLASH_TCHS (0x1 << 24) +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) /* NOR flash - not present */ #define CONFIG_SYS_NO_FLASH 1 @@ -112,7 +128,7 @@ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_ATMEL #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 #define CONFIG_SYS_NAND_DBW_8 1 /* our ALE is AD21 */ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) @@ -129,7 +145,7 @@ #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_MEMTEST_END 0x23e00000 #ifdef CONFIG_SYS_USE_DATAFLASH @@ -149,7 +165,7 @@ #else /* CONFIG_SYS_USE_NANDFLASH */ /* bootstrap + u-boot + env + linux in nandflash */ -#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ @@ -161,25 +177,20 @@ #endif -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } - #define CONFIG_SYS_PROMPT "U-Boot> " #define CONFIG_SYS_CBSIZE 256 #define CONFIG_SYS_MAXARGS 16 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_CMDLINE_EDITING 1 /* * Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) #define CONFIG_STACKSIZE (32*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -#error CONFIG_USE_IRQ not supported -#endif +#undef CONFIG_USE_IRQ #endif -- cgit v1.3.1 From f7aea46d6ad9c257d2fbea7238cc8796aaa733f1 Mon Sep 17 00:00:00 2001 From: "Xu, Hong" Date: Sun, 31 Jul 2011 22:49:00 +0000 Subject: AT91: Board fix for AT91SAM9261-EK Fix board part of AT91SAM9261-EK according to the new scheme Signed-off-by: Hong Xu Signed-off-by: Reinhard Meyer --- Makefile | 23 ----- board/atmel/at91sam9261ek/at91sam9261ek.c | 136 ++++++++++++++++-------------- board/atmel/at91sam9261ek/config.mk | 1 - board/atmel/at91sam9261ek/led.c | 7 +- boards.cfg | 6 ++ include/configs/at91sam9261ek.h | 133 +++++++++++++++-------------- 6 files changed, 154 insertions(+), 152 deletions(-) delete mode 100644 board/atmel/at91sam9261ek/config.mk (limited to 'board') diff --git a/Makefile b/Makefile index 54b88043283..28398a39d49 100644 --- a/Makefile +++ b/Makefile @@ -802,29 +802,6 @@ M5485HFE_config : unconfig ## ARM926EJ-S Systems ######################################################################### -at91sam9261ek_nandflash_config \ -at91sam9261ek_dataflash_cs0_config \ -at91sam9261ek_dataflash_cs3_config \ -at91sam9261ek_config \ -at91sam9g10ek_nandflash_config \ -at91sam9g10ek_dataflash_cs0_config \ -at91sam9g10ek_dataflash_cs3_config \ -at91sam9g10ek_config : unconfig - @mkdir -p $(obj)include - @if [ "$(findstring 9g10,$@)" ] ; then \ - echo "#define CONFIG_AT91SAM9G10EK 1" >>$(obj)include/config.h ; \ - else \ - echo "#define CONFIG_AT91SAM9261EK 1" >>$(obj)include/config.h ; \ - fi; - @if [ "$(findstring _nandflash,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_NANDFLASH 1" >>$(obj)include/config.h ; \ - elif [ "$(findstring dataflash_cs0,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_DATAFLASH_CS3 1" >>$(obj)include/config.h ; \ - else \ - echo "#define CONFIG_SYS_USE_DATAFLASH_CS0 1" >>$(obj)include/config.h ; \ - fi; - @$(MKCONFIG) -n $@ -a at91sam9261ek arm arm926ejs at91sam9261ek atmel at91 - at91sam9263ek_norflash_config \ at91sam9263ek_norflash_boot_config \ at91sam9263ek_nandflash_config \ diff --git a/board/atmel/at91sam9261ek/at91sam9261ek.c b/board/atmel/at91sam9261ek/at91sam9261ek.c index de5cfaeb00a..b6c7d9e02c5 100644 --- a/board/atmel/at91sam9261ek/at91sam9261ek.c +++ b/board/atmel/at91sam9261ek/at91sam9261ek.c @@ -23,6 +23,7 @@ */ #include +#include #include #include #include @@ -31,7 +32,6 @@ #include #include #include -#include #include #include #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000) @@ -49,44 +49,48 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_CMD_NAND static void at91sam9261ek_nand_hw_init(void) { + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX; + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; unsigned long csa; /* Enable CS3 */ - csa = at91_sys_read(AT91_MATRIX_EBICSA); - at91_sys_write(AT91_MATRIX_EBICSA, - csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA; + + writel(csa, &matrix->ebicsa); /* Configure SMC CS3 for NAND/SmartMedia */ #ifdef CONFIG_AT91SAM9G10EK - at91_sys_write(AT91_SMC_SETUP(3), - AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), - AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(7) | - AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(7)); - at91_sys_write(AT91_SMC_CYCLE(3), - AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7)); + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(7) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(7), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(7), + &smc->cs[3].cycle); #else - at91_sys_write(AT91_SMC_SETUP(3), - AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(3), - AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) | - AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3)); - at91_sys_write(AT91_SMC_CYCLE(3), - AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5)); + writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[3].setup); + writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) | + AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3), + &smc->cs[3].pulse); + writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5), + &smc->cs[3].cycle); #endif - at91_sys_write(AT91_SMC_MODE(3), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | #ifdef CONFIG_SYS_NAND_DBW_16 - AT91_SMC_DBW_16 | + AT91_SMC_MODE_DBW_16 | #else /* CONFIG_SYS_NAND_DBW_8 */ - AT91_SMC_DBW_8 | + AT91_SMC_MODE_DBW_8 | #endif - AT91_SMC_TDF_(2)); + AT91_SMC_MODE_TDF_CYCLE(2), + &smc->cs[3].mode); - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOC); + writel(1 << ATMEL_ID_PIOC, &pmc->pcer); /* Configure RDY/BSY */ at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); @@ -102,35 +106,37 @@ static void at91sam9261ek_nand_hw_init(void) #ifdef CONFIG_DRIVER_DM9000 static void at91sam9261ek_dm9000_hw_init(void) { + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + /* Configure SMC CS2 for DM9000 */ #ifdef CONFIG_AT91SAM9G10EK - at91_sys_write(AT91_SMC_SETUP(2), - AT91_SMC_NWESETUP_(3) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(3) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(2), - AT91_SMC_NWEPULSE_(6) | AT91_SMC_NCS_WRPULSE_(8) | - AT91_SMC_NRDPULSE_(6) | AT91_SMC_NCS_RDPULSE_(8)); - at91_sys_write(AT91_SMC_CYCLE(2), - AT91_SMC_NWECYCLE_(20) | AT91_SMC_NRDCYCLE_(20)); - at91_sys_write(AT91_SMC_MODE(2), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | - AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | - AT91_SMC_TDF_(1)); + writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(3) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[2].setup); + writel(AT91_SMC_PULSE_NWE(6) | AT91_SMC_PULSE_NCS_WR(8) | + AT91_SMC_PULSE_NRD(6) | AT91_SMC_PULSE_NCS_RD(8), + &smc->cs[2].pulse); + writel(AT91_SMC_CYCLE_NWE(20) | AT91_SMC_CYCLE_NRD(20), + &smc->cs[2].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | + AT91_SMC_MODE_TDF_CYCLE(1), + &smc->cs[2].mode); #else - at91_sys_write(AT91_SMC_SETUP(2), - AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | - AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0)); - at91_sys_write(AT91_SMC_PULSE(2), - AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | - AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8)); - at91_sys_write(AT91_SMC_CYCLE(2), - AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16)); - at91_sys_write(AT91_SMC_MODE(2), - AT91_SMC_READMODE | AT91_SMC_WRITEMODE | - AT91_SMC_EXNWMODE_DISABLE | - AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | - AT91_SMC_TDF_(1)); + writel(AT91_SMC_SETUP_NWE(3) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[2].setup); + writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) | + AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8), + &smc->cs[2].pulse); + writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16), + &smc->cs[2].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | + AT91_SMC_MODE_TDF_CYCLE(1), + &smc->cs[2].mode); #endif /* Configure Reset signal as output */ @@ -156,7 +162,7 @@ vidinfo_t panel_info = { vl_vsync_len: 1, vl_upper_margin:1, vl_lower_margin:0, - mmio: AT91SAM9261_LCDC_BASE, + mmio: ATMEL_BASE_LCDC, }; void lcd_enable(void) @@ -171,6 +177,8 @@ void lcd_disable(void) static void at91sam9261ek_lcd_hw_init(void) { + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + at91_set_A_periph(AT91_PIN_PB1, 0); /* LCDHSYNC */ at91_set_A_periph(AT91_PIN_PB2, 0); /* LCDDOTCK */ at91_set_A_periph(AT91_PIN_PB3, 0); /* LCDDEN */ @@ -194,12 +202,11 @@ static void at91sam9261ek_lcd_hw_init(void) at91_set_B_periph(AT91_PIN_PB27, 0); /* LCDD22 */ at91_set_B_periph(AT91_PIN_PB28, 0); /* LCDD23 */ - at91_sys_write(AT91_PMC_SCER, AT91_PMC_HCK1); + writel(AT91_PMC_HCK1, &pmc->scer); -#ifdef CONFIG_AT91SAM9G10EK - gd->fb_base = CONFIG_AT91SAM9G10_LCD_BASE; -#else - gd->fb_base = AT91SAM9261_SRAM_BASE; + /* For 9G10EK, let U-Boot allocate the framebuffer in SDRAM */ +#ifdef CONFIG_AT91SAM9261EK + gd->fb_base = ATMEL_BASE_SRAM; #endif } @@ -217,7 +224,7 @@ void lcd_show_board_info(void) lcd_printf ("(C) 2008 ATMEL Corp\n"); lcd_printf ("at91support@atmel.com\n"); lcd_printf ("%s CPU at %s MHz\n", - CONFIG_SYS_AT91_CPU_NAME, + ATMEL_CPU_NAME, strmhz(temp, get_cpu_clk_rate())); dram_size = 0; @@ -246,9 +253,9 @@ int board_init(void) gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9261EK; #endif /* adress of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - at91_serial_hw_init(); + at91_seriald_hw_init(); #ifdef CONFIG_CMD_NAND at91sam9261ek_nand_hw_init(); #endif @@ -273,8 +280,9 @@ int board_eth_init(bd_t *bis) int dram_init(void) { - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; } diff --git a/board/atmel/at91sam9261ek/config.mk b/board/atmel/at91sam9261ek/config.mk deleted file mode 100644 index e554a450073..00000000000 --- a/board/atmel/at91sam9261ek/config.mk +++ /dev/null @@ -1 +0,0 @@ -CONFIG_SYS_TEXT_BASE = 0x23f00000 diff --git a/board/atmel/at91sam9261ek/led.c b/board/atmel/at91sam9261ek/led.c index 5d1c5f2f8ba..0c2f522825c 100644 --- a/board/atmel/at91sam9261ek/led.c +++ b/board/atmel/at91sam9261ek/led.c @@ -26,12 +26,15 @@ #include #include #include -#include +#include +#include void coloured_LED_init(void) { + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + /* Enable clock */ - at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9261_ID_PIOA); + writel(ATMEL_ID_PIOA, &pmc->pcer); at91_set_gpio_output(CONFIG_RED_LED, 1); at91_set_gpio_output(CONFIG_GREEN_LED, 1); diff --git a/boards.cfg b/boards.cfg index 8a5a618416c..f77ecfcd304 100644 --- a/boards.cfg +++ b/boards.cfg @@ -77,6 +77,12 @@ at91cap9adk arm arm926ejs - atmel at91sam9260ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH at91sam9260ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS0 at91sam9260ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_DATAFLASH_CS1 +at91sam9261ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_NANDFLASH +at91sam9261ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS0 +at91sam9261ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS3 +at91sam9g10ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH +at91sam9g10ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0 +at91sam9g10ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3 at91sam9g20ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH at91sam9g20ek_dataflash_cs0 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0 at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1 diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h index 401478b2705..126907f445c 100644 --- a/include/configs/at91sam9261ek.h +++ b/include/configs/at91sam9261ek.h @@ -27,52 +27,62 @@ #ifndef __CONFIG_H #define __CONFIG_H -#define CONFIG_AT91_LEGACY - /* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */ -#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_HZ 1000 -#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ -#ifdef CONFIG_AT91SAM9G10EK -#define CONFIG_AT91SAM9G10 1 /* It's an Atmel AT91SAM9G10 SoC*/ +#ifdef CONFIG_AT91SAM9G10 +#define CONFIG_AT91SAM9G10EK /* It's an Atmel AT91SAM9G10 EK*/ #else -#define CONFIG_AT91SAM9261 1 /* It's an Atmel AT91SAM9261 SoC*/ +#define CONFIG_AT91SAM9261EK /* It's an Atmel AT91SAM9261 EK*/ #endif + +#include + #define CONFIG_ARCH_CPU_INIT #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG #define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_ATMEL_LEGACY +#define CONFIG_SYS_TEXT_BASE 0x21f00000 + /* * Hardware drivers */ -#define CONFIG_AT91_GPIO 1 -#define CONFIG_ATMEL_USART 1 -#undef CONFIG_USART0 -#undef CONFIG_USART1 -#undef CONFIG_USART2 -#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +/* gpio */ +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200, 57600, 38400, 19200, 9600} /* LCD */ -#define CONFIG_LCD 1 +#define CONFIG_LCD #define LCD_BPP LCD_COLOR8 -#define CONFIG_LCD_LOGO 1 +#define CONFIG_LCD_LOGO #undef LCD_TEST_PATTERN -#define CONFIG_LCD_INFO 1 -#define CONFIG_LCD_INFO_BELOW_LOGO 1 -#define CONFIG_SYS_WHITE_ON_BLACK 1 -#define CONFIG_ATMEL_LCD 1 +#define CONFIG_LCD_INFO +#define CONFIG_LCD_INFO_BELOW_LOGO +#define CONFIG_SYS_WHITE_ON_BLACK +#define CONFIG_ATMEL_LCD #ifdef CONFIG_AT91SAM9261EK -#define CONFIG_ATMEL_LCD_BGR555 1 -#else -#define CONFIG_AT91SAM9G10_LCD_BASE 0x23E00000 /* LCD is no more in SRAM */ +#define CONFIG_ATMEL_LCD_BGR555 #endif -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 + +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* LED */ #define CONFIG_AT91_LED @@ -85,10 +95,10 @@ /* * BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE 1 -#define CONFIG_BOOTP_BOOTPATH 1 -#define CONFIG_BOOTP_GATEWAY 1 -#define CONFIG_BOOTP_HOSTNAME 1 +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. @@ -101,33 +111,35 @@ #undef CONFIG_CMD_LOADS #undef CONFIG_CMD_SOURCE -#define CONFIG_CMD_PING 1 -#define CONFIG_CMD_DHCP 1 -#define CONFIG_CMD_NAND 1 -#define CONFIG_CMD_USB 1 +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NAND +#define CONFIG_CMD_USB /* SDRAM */ #define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM 0x20000000 -#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ +#define CONFIG_SYS_SDRAM_BASE 0x20000000 +#define CONFIG_SYS_SDRAM_SIZE 0x04000000 +#define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE) /* DataFlash */ #define CONFIG_ATMEL_DATAFLASH_SPI -#define CONFIG_HAS_DATAFLASH 1 +#define CONFIG_HAS_DATAFLASH #define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ) #define CONFIG_SYS_MAX_DATAFLASH_BANKS 2 #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* CS3 */ -#define AT91_SPI_CLK 15000000 -#define DATAFLASH_TCSS (0x1a << 16) -#define DATAFLASH_TCHS (0x1 << 24) +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) /* NAND flash */ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_ATMEL #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x40000000 -#define CONFIG_SYS_NAND_DBW_8 1 +#define CONFIG_SYS_NAND_DBW_8 /* our ALE is AD22 */ #define CONFIG_SYS_NAND_MASK_ALE (1 << 22) /* our CLE is AD21 */ @@ -138,24 +150,24 @@ #endif /* NOR flash - no real flash on this board */ -#define CONFIG_SYS_NO_FLASH 1 +#define CONFIG_SYS_NO_FLASH /* Ethernet */ -#define CONFIG_NET_MULTI 1 -#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_NET_MULTI +#define CONFIG_DRIVER_DM9000 #define CONFIG_DM9000_BASE 0x30000000 #define DM9000_IO CONFIG_DM9000_BASE #define DM9000_DATA (CONFIG_DM9000_BASE + 4) -#define CONFIG_DM9000_USE_16BIT 1 -#define CONFIG_DM9000_NO_SROM 1 +#define CONFIG_DM9000_USE_16BIT +#define CONFIG_DM9000_NO_SROM #define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_RESET_PHY_R 1 +#define CONFIG_RESET_PHY_R /* USB */ #define CONFIG_USB_ATMEL -#define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_DOS_PARTITION 1 -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_USB_OHCI_NEW +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9261_UHP_BASE */ #ifdef CONFIG_AT91SAM9G10EK #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g10" @@ -163,18 +175,18 @@ #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9261" #endif #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 -#define CONFIG_USB_STORAGE 1 -#define CONFIG_CMD_FAT 1 +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_FAT #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_MEMTEST_END 0x23e00000 #ifdef CONFIG_SYS_USE_DATAFLASH_CS0 /* bootstrap + u-boot + env + linux in dataflash on CS0 */ -#define CONFIG_ENV_IS_IN_DATAFLASH 1 +#define CONFIG_ENV_IS_IN_DATAFLASH #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) #define CONFIG_ENV_OFFSET 0x4200 #define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET) @@ -188,7 +200,7 @@ #elif CONFIG_SYS_USE_DATAFLASH_CS3 /* bootstrap + u-boot + env + linux in dataflash on CS3 */ -#define CONFIG_ENV_IS_IN_DATAFLASH 1 +#define CONFIG_ENV_IS_IN_DATAFLASH #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + 0x8400) #define CONFIG_ENV_OFFSET 0x4200 #define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + CONFIG_ENV_OFFSET) @@ -202,7 +214,7 @@ #else /* CONFIG_SYS_USE_NANDFLASH */ /* bootstrap + u-boot + env + linux in nandflash */ -#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ @@ -216,22 +228,19 @@ #endif -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } - #define CONFIG_SYS_PROMPT "U-Boot> " #define CONFIG_SYS_CBSIZE 256 #define CONFIG_SYS_MAXARGS 16 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) -#define CONFIG_STACKSIZE (32*1024) /* regular stack */ +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ #ifdef CONFIG_USE_IRQ #error CONFIG_USE_IRQ not supported -- cgit v1.3.1 From cd46b0f2b97771a19c3997e713d22bfb374815bb Mon Sep 17 00:00:00 2001 From: "Xu, Hong" Date: Fri, 10 Jun 2011 21:31:26 +0000 Subject: AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master Rework for AT91SAM9263-EK, makes it build again. Based on the work for AT91SAM9260-EK. Signed-off-by: Hong Xu Signed-off-by: Reinhard Meyer --- Makefile | 19 ------- board/atmel/at91sam9263ek/at91sam9263ek.c | 56 +++++++++++++-------- board/atmel/at91sam9263ek/config.mk | 1 - board/atmel/at91sam9263ek/led.c | 23 ++++----- boards.cfg | 5 ++ include/configs/at91sam9263ek.h | 83 +++++++++++++++++-------------- 6 files changed, 98 insertions(+), 89 deletions(-) delete mode 100644 board/atmel/at91sam9263ek/config.mk (limited to 'board') diff --git a/Makefile b/Makefile index 28398a39d49..aa788513d77 100644 --- a/Makefile +++ b/Makefile @@ -802,25 +802,6 @@ M5485HFE_config : unconfig ## ARM926EJ-S Systems ######################################################################### -at91sam9263ek_norflash_config \ -at91sam9263ek_norflash_boot_config \ -at91sam9263ek_nandflash_config \ -at91sam9263ek_dataflash_config \ -at91sam9263ek_dataflash_cs0_config \ -at91sam9263ek_config : unconfig - @mkdir -p $(obj)include - @if [ "$(findstring _nandflash,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_NANDFLASH 1" >>$(obj)include/config.h ; \ - elif [ "$(findstring norflash,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_NORFLASH 1" >>$(obj)include/config.h ; \ - else \ - echo "#define CONFIG_SYS_USE_DATAFLASH 1" >>$(obj)include/config.h ; \ - fi; - @if [ "$(findstring norflash_boot,$@)" ] ; then \ - echo "#define CONFIG_SYS_USE_BOOT_NORFLASH 1" >>$(obj)include/config.h ; \ - fi; - @$(MKCONFIG) -n $@ -a at91sam9263ek arm arm926ejs at91sam9263ek atmel at91 - at91sam9m10g45ek_nandflash_config \ at91sam9m10g45ek_dataflash_config \ at91sam9m10g45ek_dataflash_cs0_config \ diff --git a/board/atmel/at91sam9263ek/at91sam9263ek.c b/board/atmel/at91sam9263ek/at91sam9263ek.c index 91efc07ffd1..4d2937d2dbb 100644 --- a/board/atmel/at91sam9263ek/at91sam9263ek.c +++ b/board/atmel/at91sam9263ek/at91sam9263ek.c @@ -32,7 +32,8 @@ #include #include #include -#include +#include +#include #include #include #include @@ -52,9 +53,9 @@ DECLARE_GLOBAL_DATA_PTR; static void at91sam9263ek_nand_hw_init(void) { unsigned long csa; - at91_smc_t *smc = (at91_smc_t *) AT91_SMC0_BASE; - at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE; - at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0; + at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; /* Enable CS3 */ csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A; @@ -83,14 +84,14 @@ static void at91sam9263ek_nand_hw_init(void) AT91_SMC_MODE_TDF_CYCLE(2), &smc->cs[3].mode); - writel(1 << AT91SAM9263_ID_PIOA | 1 << AT91SAM9263_ID_PIOCDE, + writel(1 << ATMEL_ID_PIOA | 1 << ATMEL_ID_PIOCDE, &pmc->pcer); /* Configure RDY/BSY */ - at91_set_pio_input(CONFIG_SYS_NAND_READY_PIN, 1); + at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1); /* Enable NandFlash */ - at91_set_pio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); + at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1); } #endif @@ -98,11 +99,11 @@ static void at91sam9263ek_nand_hw_init(void) static void at91sam9263ek_macb_hw_init(void) { unsigned long erstl; - at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; - at91_pio_t *pio = (at91_pio_t *) AT91_PIO_BASE; - at91_rstc_t *rstc = (at91_rstc_t *) AT91_RSTC_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; + at91_pio_t *pio = (at91_pio_t *) ATMEL_BASE_PIO; + at91_rstc_t *rstc = (at91_rstc_t *) ATMEL_BASE_RSTC; /* Enable clock */ - writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer); + writel(1 << ATMEL_ID_EMAC, &pmc->pcer); /* * Disable pull-up on: @@ -153,7 +154,7 @@ vidinfo_t panel_info = { vl_vsync_len: 1, vl_upper_margin:1, vl_lower_margin:0, - mmio: AT91SAM9263_LCDC_BASE, + mmio: ATMEL_BASE_LCDC, }; void lcd_enable(void) @@ -168,7 +169,7 @@ void lcd_disable(void) static void at91sam9263ek_lcd_hw_init(void) { - at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */ at91_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDDOTCK */ @@ -193,8 +194,8 @@ static void at91sam9263ek_lcd_hw_init(void) at91_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDD22 */ at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */ - writel(1 << AT91SAM9263_ID_LCDC, &pmc->pcer); - gd->fb_base = AT91SAM9263_SRAM0_BASE; + writel(1 << ATMEL_ID_LCDC, &pmc->pcer); + gd->fb_base = ATMEL_BASE_SRAM0; } #ifdef CONFIG_LCD_INFO @@ -218,7 +219,7 @@ void lcd_show_board_info(void) lcd_printf ("(C) 2008 ATMEL Corp\n"); lcd_printf ("at91support@atmel.com\n"); lcd_printf ("%s CPU at %s MHz\n", - CONFIG_SYS_AT91_CPU_NAME, + ATMEL_CPU_NAME, strmhz(temp, get_cpu_clk_rate())); dram_size = 0; @@ -244,6 +245,18 @@ void lcd_show_board_info(void) #endif /* CONFIG_LCD_INFO */ #endif +int board_early_init_f(void) +{ + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC; + + /* Enable clocks for all PIOs */ + writel((1 << ATMEL_ID_PIOA) | (1 << ATMEL_ID_PIOB) | + (1 << ATMEL_ID_PIOCDE), + &pmc->pcer); + + return 0; +} + int board_init(void) { /* Enable Ctrlc */ @@ -252,9 +265,9 @@ int board_init(void) /* arch number of AT91SAM9263EK-Board */ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9263EK; /* adress of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; - at91_serial_hw_init(); + at91_seriald_hw_init(); #ifdef CONFIG_CMD_NAND at91sam9263ek_nand_hw_init(); #endif @@ -276,8 +289,9 @@ int board_init(void) int dram_init(void) { - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); + return 0; } @@ -291,7 +305,7 @@ int board_eth_init(bd_t *bis) { int rc = 0; #ifdef CONFIG_MACB - rc = macb_eth_initialize(0, (void *) AT91_EMAC_BASE, 0x00); + rc = macb_eth_initialize(0, (void *) ATMEL_BASE_EMAC, 0x00); #endif return rc; } diff --git a/board/atmel/at91sam9263ek/config.mk b/board/atmel/at91sam9263ek/config.mk deleted file mode 100644 index e554a450073..00000000000 --- a/board/atmel/at91sam9263ek/config.mk +++ /dev/null @@ -1 +0,0 @@ -CONFIG_SYS_TEXT_BASE = 0x23f00000 diff --git a/board/atmel/at91sam9263ek/led.c b/board/atmel/at91sam9263ek/led.c index fa1f05b0de1..c44455e6641 100644 --- a/board/atmel/at91sam9263ek/led.c +++ b/board/atmel/at91sam9263ek/led.c @@ -23,25 +23,24 @@ */ #include -#include -#include -#include +#include #include -#include +#include +#include void coloured_LED_init(void) { /* Enable clock */ - at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE; + at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC; - writel(1 << AT91SAM9263_ID_PIOB | 1 << AT91SAM9263_ID_PIOCDE, + writel(1 << ATMEL_ID_PIOB | 1 << ATMEL_ID_PIOCDE, &pmc->pcer); - at91_set_pio_output(CONFIG_RED_LED, 1); - at91_set_pio_output(CONFIG_GREEN_LED, 1); - at91_set_pio_output(CONFIG_YELLOW_LED, 1); + at91_set_gpio_output(CONFIG_RED_LED, 1); + at91_set_gpio_output(CONFIG_GREEN_LED, 1); + at91_set_gpio_output(CONFIG_YELLOW_LED, 1); - at91_set_pio_value(CONFIG_RED_LED, 0); - at91_set_pio_value(CONFIG_GREEN_LED, 1); - at91_set_pio_value(CONFIG_YELLOW_LED, 1); + at91_set_gpio_value(CONFIG_RED_LED, 0); + at91_set_gpio_value(CONFIG_GREEN_LED, 1); + at91_set_gpio_value(CONFIG_YELLOW_LED, 1); } diff --git a/boards.cfg b/boards.cfg index f77ecfcd304..e5018908d5d 100644 --- a/boards.cfg +++ b/boards.cfg @@ -80,6 +80,11 @@ at91sam9260ek_dataflash_cs1 arm arm926ejs at91sam9260ek atmel at91sam9261ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_NANDFLASH at91sam9261ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS0 at91sam9261ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9261,SYS_USE_DATAFLASH_CS3 +at91sam9263ek_nandflash arm arm926ejs at91sam9263ek atmel at91 at91sam9263ek:AT91SAM9263,SYS_USE_NANDFLASH +at91sam9263ek_dataflash_cs0 arm arm926ejs at91sam9263ek atmel at91 at91sam9263ek:AT91SAM9263,SYS_USE_DATAFLASH +at91sam9263ek_dataflash arm arm926ejs at91sam9263ek atmel at91 at91sam9263ek:AT91SAM9263,SYS_USE_DATAFLASH +at91sam9263ek_norflash arm arm926ejs at91sam9263ek atmel at91 at91sam9263ek:AT91SAM9263,SYS_USE_NORFLASH +at91sam9263ek_norflash_boot arm arm926ejs at91sam9263ek atmel at91 at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH at91sam9g10ek_nandflash arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH at91sam9g10ek_dataflash_cs0 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0 at91sam9g10ek_dataflash_cs3 arm arm926ejs at91sam9261ek atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3 diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index f6cb40684fd..d817423a7ed 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -27,13 +27,21 @@ #ifndef __CONFIG_H #define __CONFIG_H +/* + * SoC must be defined first, before hardware.h is included. + * In this case SoC is defined in boards.cfg. + */ +#include + +#define CONFIG_SYS_TEXT_BASE 0x21F00000 + /* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 16367660 /* 16.367 MHz crystal */ -#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_AT91_MAIN_CLOCK 16367660 /* 16.367 MHz crystal */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91SAM9263EK 1 /* It's an AT91SAM9263EK Board */ -#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ -#define CONFIG_AT91SAM9263 1 /* It's an Atmel AT91SAM9263 SoC*/ -#define CONFIG_AT91SAM9263EK 1 /* on an AT91SAM9263EK Board */ #define CONFIG_ARCH_CPU_INIT #undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ @@ -43,17 +51,27 @@ #ifndef CONFIG_SYS_USE_BOOT_NORFLASH #define CONFIG_SKIP_LOWLEVEL_INIT +#else +#define CONFIG_SYS_USE_NORFLASH #endif +#define CONFIG_BOARD_EARLY_INIT_F + +#define CONFIG_DISPLAY_CPUINFO + /* * Hardware drivers */ -#define CONFIG_AT91_GPIO 1 -#define CONFIG_ATMEL_USART 1 -#undef CONFIG_USART0 -#undef CONFIG_USART1 -#undef CONFIG_USART2 -#define CONFIG_USART3 1 /* USART 3 is DBGU */ +#define CONFIG_ATMEL_LEGACY +#define CONFIG_AT91_GPIO 1 +#define CONFIG_AT91_GPIO_PULLUP 1 + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {115200, 19200, 38400, 57600, 9600} /* LCD */ #define CONFIG_LCD 1 @@ -62,16 +80,16 @@ #undef LCD_TEST_PATTERN #define CONFIG_LCD_INFO 1 #define CONFIG_LCD_INFO_BELOW_LOGO 1 -#define CONFIG_SYS_WHITE_ON_BLACK 1 +#define CONFIG_SYS_WHITE_ON_BLACK 1 #define CONFIG_ATMEL_LCD 1 #define CONFIG_ATMEL_LCD_BGR555 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 /* LED */ #define CONFIG_AT91_LED -#define CONFIG_RED_LED AT91_PIO_PORTB, 7 /* the power led */ -#define CONFIG_GREEN_LED AT91_PIO_PORTB, 8 /* the user1 led */ -#define CONFIG_YELLOW_LED AT91_PIO_PORTC, 29 /* the user2 led */ +#define CONFIG_RED_LED AT91_PIN_PB7 /* the power led */ +#define CONFIG_GREEN_LED AT91_PIN_PB8 /* the user1 led */ +#define CONFIG_YELLOW_LED AT91_PIN_PC29 /* the user2 led */ #define CONFIG_BOOTDELAY 3 @@ -101,8 +119,11 @@ /* SDRAM */ #define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM 0x20000000 -#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE 0x04000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) /* DataFlash */ #define CONFIG_ATMEL_DATAFLASH_SPI @@ -254,19 +275,14 @@ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_ATMEL #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x40000000 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 #define CONFIG_SYS_NAND_DBW_8 1 /* our ALE is AD21 */ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22 -/* -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22 -*/ - +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD15 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PA22 #define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif @@ -291,7 +307,7 @@ #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_MEMTEST_END 0x23e00000 #ifdef CONFIG_SYS_USE_DATAFLASH @@ -311,7 +327,7 @@ #elif CONFIG_SYS_USE_NANDFLASH /* bootstrap + u-boot + env + linux in nandflash */ -#define CONFIG_ENV_IS_IN_NAND 1 +#define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_OFFSET 0x60000 #define CONFIG_ENV_OFFSET_REDUND 0x80000 #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ @@ -323,15 +339,12 @@ #endif -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } - #define CONFIG_SYS_PROMPT "U-Boot> " #define CONFIG_SYS_CBSIZE 256 #define CONFIG_SYS_MAXARGS 16 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_LONGHELP 1 -#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_CMDLINE_EDITING 1 #define CONFIG_AUTO_COMPLETE #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " @@ -339,12 +352,10 @@ /* * Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) #define CONFIG_STACKSIZE (32*1024) /* regular stack */ -#ifdef CONFIG_USE_IRQ -#error CONFIG_USE_IRQ not supported -#endif +#undef CONFIG_USE_IRQ #endif -- cgit v1.3.1 From ad7a1785f77216da89769d530a29b157e4f5a53a Mon Sep 17 00:00:00 2001 From: Andreas Bießmann Date: Thu, 30 Jun 2011 22:03:20 +0000 Subject: avr32: add grasshopper (ICnova AP7000) board MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The grasshopper board is a neat avr32 evaluation kit produced by In-Circuit GmbH. See http://www.ic-board.de/product_info.php?info=p75_ICnova-AP7000-Base.html for detailed information about this device. Signed-off-by: Andreas Bießmann Signed-off-by: Reinhard Meyer --- MAINTAINERS | 1 + board/in-circuit/grasshopper/Makefile | 45 +++++++ board/in-circuit/grasshopper/grasshopper.c | 112 ++++++++++++++++ boards.cfg | 1 + include/configs/grasshopper.h | 198 +++++++++++++++++++++++++++++ 5 files changed, 357 insertions(+) create mode 100644 board/in-circuit/grasshopper/Makefile create mode 100644 board/in-circuit/grasshopper/grasshopper.c create mode 100644 include/configs/grasshopper.h (limited to 'board') diff --git a/MAINTAINERS b/MAINTAINERS index f8d85590bf8..fd4181f072a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -600,6 +600,7 @@ Rishi Bhattacharya Andreas Bießmann at91rm9200ek at91rm9200 + grasshopper avr32 Cliff Brake diff --git a/board/in-circuit/grasshopper/Makefile b/board/in-circuit/grasshopper/Makefile new file mode 100644 index 00000000000..a6c36c79832 --- /dev/null +++ b/board/in-circuit/grasshopper/Makefile @@ -0,0 +1,45 @@ +# +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2011 +# Corscience GmbH & Co.KG, Andreas Bießmann +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +include $(TOPDIR)/config.mk + +LIB := $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o + +SRCS := $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/in-circuit/grasshopper/grasshopper.c b/board/in-circuit/grasshopper/grasshopper.c new file mode 100644 index 00000000000..475a759b7a5 --- /dev/null +++ b/board/in-circuit/grasshopper/grasshopper.c @@ -0,0 +1,112 @@ +/* + * Copyright (C) 2011 + * Corscience GmbH & Co.KG, Andreas Bießmann + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include + +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = { + { + .virt_pgno = CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT, + .nr_pages = CONFIG_SYS_FLASH_SIZE >> PAGE_SHIFT, + .phys = (CONFIG_SYS_FLASH_BASE >> PAGE_SHIFT) + | MMU_VMR_CACHE_NONE, + }, { + .virt_pgno = CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT, + .nr_pages = EBI_SDRAM_SIZE >> PAGE_SHIFT, + .phys = (CONFIG_SYS_SDRAM_BASE >> PAGE_SHIFT) + | MMU_VMR_CACHE_WRBACK, + }, +}; + +static const struct sdram_config sdram_config = { + /* Dual MT48LC16M16A2-7E (or equal) */ + .data_bits = SDRAM_DATA_32BIT, + .row_bits = 13, + .col_bits = 9, + .bank_bits = 2, + .cas = 2, + .twr = 2, + .trc = 7, + .trp = 2, + .trcd = 2, + .tras = 4, + .txsr = 7, + /* 7.81 us */ + .refresh_period = (781 * (SDRAMC_BUS_HZ / 1000)) / 100000, +}; + +int board_early_init_f(void) +{ + /* Enable SDRAM in the EBI mux */ + hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE)); + + portmux_enable_ebi(SDRAM_DATA_32BIT, 23, 0, PORTMUX_DRIVE_HIGH); + portmux_enable_usart0(PORTMUX_DRIVE_MIN); + portmux_enable_usart1(PORTMUX_DRIVE_MIN); +#if defined(CONFIG_MACB) + portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_LOW); +#endif + + return 0; +} + +phys_size_t initdram(int board_type) +{ + unsigned long expected_size; + unsigned long actual_size; + void *sdram_base; + + sdram_base = uncached(EBI_SDRAM_BASE); + + expected_size = sdram_init(sdram_base, &sdram_config); + actual_size = get_ram_size(sdram_base, expected_size); + + if (expected_size != actual_size) + printf("Warning: Only %lu of %lu MiB SDRAM is working\n", + actual_size >> 20, expected_size >> 20); + + return actual_size; +} + +int board_early_init_r(void) +{ + gd->bd->bi_phy_id[0] = 0x00; + return 0; +} + +#ifdef CONFIG_CMD_NET +int board_eth_init(bd_t *bi) +{ + macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]); + return 0; +} +#endif +/* vim: set noet ts=8: */ diff --git a/boards.cfg b/boards.cfg index e5018908d5d..38ccb8c27e2 100644 --- a/boards.cfg +++ b/boards.cfg @@ -228,6 +228,7 @@ atstk1003 avr32 at32ap atstk1000 atmel atstk1004 avr32 at32ap atstk1000 atmel at32ap700x atstk1006 avr32 at32ap atstk1000 atmel at32ap700x favr-32-ezkit avr32 at32ap - earthlcd at32ap700x +grasshopper avr32 at32ap - in-circuit at32ap700x mimc200 avr32 at32ap - mimc at32ap700x hammerhead avr32 at32ap - miromico at32ap700x bct-brettl2 blackfin blackfin diff --git a/include/configs/grasshopper.h b/include/configs/grasshopper.h new file mode 100644 index 00000000000..9779449bc6a --- /dev/null +++ b/include/configs/grasshopper.h @@ -0,0 +1,198 @@ +/* + * Copyright (C) 2011 + * Corscience GmbH & Co.KG, Andreas Bießmann + * + * Configuration settings for the grasshopper (ICnova AP7000) board + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __GRASSHOPPER_CONFIG_H +#define __GRASSHOPPER_CONFIG_H + +#include + +#define CONFIG_AVR32 +#define CONFIG_AT32AP +#define CONFIG_AT32AP7000 + +/* + * Timer clock frequency. We're using the CPU-internal COUNT register + * for this, so this is equivalent to the CPU core clock frequency + */ +#define CONFIG_SYS_HZ 1000 + +/* + * Set up the PLL to run at 140 MHz, the CPU to run at the PLL + * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the + * PLL frequency. + * (CONFIG_SYS_OSC0_HZ * CONFIG_SYS_PLL0_MUL) / CONFIG_SYS_PLL0_DIV = PLL MHz + */ +#define CONFIG_PLL +#define CONFIG_SYS_POWER_MANAGER +#define CONFIG_SYS_OSC0_HZ 20000000 +#define CONFIG_SYS_PLL0_DIV 1 +#define CONFIG_SYS_PLL0_MUL 7 +#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16 +/* + * Set the CPU running at: + * PLL / (2^CONFIG_SYS_CLKDIV_CPU) = CPU MHz + */ +#define CONFIG_SYS_CLKDIV_CPU 0 +/* + * Set the HSB running at: + * PLL / (2^CONFIG_SYS_CLKDIV_HSB) = HSB MHz + */ +#define CONFIG_SYS_CLKDIV_HSB 1 +/* + * Set the PBA running at: + * PLL / (2^CONFIG_SYS_CLKDIV_PBA) = PBA MHz + */ +#define CONFIG_SYS_CLKDIV_PBA 2 +/* + * Set the PBB running at: + * PLL / (2^CONFIG_SYS_CLKDIV_PBB) = PBB MHz + */ +#define CONFIG_SYS_CLKDIV_PBB 1 + +/* Reserve VM regions for SDRAM and NOR flash */ +#define CONFIG_SYS_NR_VM_REGIONS 2 + +/* + * The PLLOPT register controls the PLL like this: + * icp = PLLOPT<2> + * ivco = PLLOPT<1:0> + * + * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). + */ +#define CONFIG_SYS_PLL0_OPT 0x04 + +#define CONFIG_USART_BASE ATMEL_BASE_USART1 +#define CONFIG_USART_ID 1 + +/* User serviceable stuff */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +#define CONFIG_STACKSIZE (2048) + +#define CONFIG_BAUDRATE 115200 + +/* + * Only interrupt autoboot if is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d" \ + " seconds\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr". This is normally done during production. + */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE +#define CONFIG_NET_MULTI + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY + +/* + * Command line configuration. + */ +#include + +/* remove unneeded commands */ +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR + +/* add useful commands */ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_PROMPT_HUSH_PS2 "~> " +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_ATMEL_USART +#define CONFIG_MACB +#define CONFIG_PORTMUX_PIO +#define CONFIG_SYS_NR_PIOS 5 +#define CONFIG_SYS_HSDRAMC + +#define CONFIG_SYS_DCACHE_LINESZ 32 +#define CONFIG_SYS_ICACHE_LINESZ 32 + +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER + +#define CONFIG_SYS_FLASH_BASE 0x00000000 +#define CONFIG_SYS_FLASH_SIZE 0x800000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_TEXT_BASE 0x00000000 + +#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE +#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE + +#define CONFIG_ENV_IS_IN_FLASH +/* place u-boot env in flash sector after u-boot */ +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_ADDR 0x20000 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + \ + CONFIG_SYS_INTRAM_SIZE) + +#define CONFIG_SYS_MALLOC_LEN (256*1024) +#define CONFIG_SYS_DMA_ALLOC_LEN (16384) + +/* Allow 4MB for the kernel run-time image */ +#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) +#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024) + +/* Other configuration settings that shouldn't have to change all that often */ +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP + +#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x700000) +#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } + +#endif /* __GRASSHOPPER_CONFIG_H */ +/* vim: set ts=8 noet: */ -- cgit v1.3.1 From 2dd97488ee1aee3511706425853522a3fb2c8467 Mon Sep 17 00:00:00 2001 From: Dirk Behme Date: Sat, 9 Jul 2011 20:52:17 +0000 Subject: ARMv7: u8500_href: Add missing header to fix compiler warning Fix the compiler warning u8500_href.c: In function 'hrefplus_mmc_power_init': u8500_href.c:258: warning: implicit declaration of function 'prcmu_i2c_read' u8500_href.c:265: warning: implicit declaration of function 'prcmu_i2c_write' by adding the missing header file. Signed-off-by: Dirk Behme --- board/st-ericsson/u8500/u8500_href.c | 1 + 1 file changed, 1 insertion(+) (limited to 'board') diff --git a/board/st-ericsson/u8500/u8500_href.c b/board/st-ericsson/u8500/u8500_href.c index 525633e865d..9283fab6859 100644 --- a/board/st-ericsson/u8500/u8500_href.c +++ b/board/st-ericsson/u8500/u8500_href.c @@ -27,6 +27,7 @@ #include #include #ifdef CONFIG_MMC +#include "prcmu-fw.h" #include "../../../drivers/mmc/arm_pl180_mmci.h" #endif -- cgit v1.3.1 From d388298a59ba375c76597b8f95b560afa971a0fb Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 24 Jun 2011 03:04:38 +0000 Subject: ARM: versatile: fix board support MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Versatile board is used as example to run u-boot under qemu. The patch fixes relocation for all versatile boards and adds a versatileqemu target to be used under qemu. Patch tested only under qemu, not on real boards. Tested with QEMU emulator version 0.14.50. Signed-off-by: Stefano Babic CC: Alessandro Rubini CC: Loïc Minier --- Makefile | 9 --------- board/armltd/versatile/config.mk | 5 ----- board/armltd/versatile/versatile.c | 10 +++++++++- boards.cfg | 3 +++ include/configs/versatile.h | 21 ++++++++++++++++++++- 5 files changed, 32 insertions(+), 16 deletions(-) delete mode 100644 board/armltd/versatile/config.mk (limited to 'board') diff --git a/Makefile b/Makefile index aa788513d77..03d80b7c50e 100644 --- a/Makefile +++ b/Makefile @@ -933,15 +933,6 @@ edb9315_config \ edb9315a_config: unconfig @$(MKCONFIG) -n $@ -t $(@:_config=) edb93xx arm arm920t edb93xx - ep93xx -######################################################################### -# ARM supplied Versatile development boards -######################################################################### - -versatile_config \ -versatileab_config \ -versatilepb_config : unconfig - @board/armltd/versatile/split_by_variant.sh $@ - ######################################################################### ## XScale Systems ######################################################################### diff --git a/board/armltd/versatile/config.mk b/board/armltd/versatile/config.mk deleted file mode 100644 index 8b57af1c5e8..00000000000 --- a/board/armltd/versatile/config.mk +++ /dev/null @@ -1,5 +0,0 @@ -# -# image should be loaded at 0x01000000 -# - -CONFIG_SYS_TEXT_BASE = 0x01000000 diff --git a/board/armltd/versatile/versatile.c b/board/armltd/versatile/versatile.c index 6e836dd1f93..ee8cb5e3c7d 100644 --- a/board/armltd/versatile/versatile.c +++ b/board/armltd/versatile/versatile.c @@ -51,7 +51,7 @@ void show_boot_progress(int progress) * Miscellaneous platform dependent initialisations */ -int board_init (void) +int board_early_init_f (void) { /* * set clock frequency: @@ -62,6 +62,11 @@ int board_init (void) ((VERSATILE_TIMCLK << VERSATILE_TIMER1_EnSel) | (VERSATILE_TIMCLK << VERSATILE_TIMER2_EnSel) | (VERSATILE_TIMCLK << VERSATILE_TIMER3_EnSel) | (VERSATILE_TIMCLK << VERSATILE_TIMER4_EnSel)); + return 0; +} + +int board_init (void) +{ /* arch number of Versatile Board */ gd->bd->bi_arch_number = MACH_TYPE_VERSATILE_PB; @@ -88,6 +93,9 @@ int misc_init_r (void) ******************************/ int dram_init (void) { + /* dram_init must store complete ramsize in gd->ram_size */ + gd->ram_size = get_ram_size((volatile void *)CONFIG_SYS_SDRAM_BASE, + PHYS_SDRAM_1_SIZE); return 0; } diff --git a/boards.cfg b/boards.cfg index 38ccb8c27e2..3fe7d1bc6ad 100644 --- a/boards.cfg +++ b/boards.cfg @@ -71,6 +71,9 @@ smdk2410 arm arm920t - samsung netstar arm arm925t voiceblue arm arm925t omap1510inn arm arm925t - ti +versatileqemu arm arm926ejs versatile armltd versatile versatile:ARCH_VERSATILE_QEMU +versatilepb arm arm926ejs versatile armltd versatile versatile:ARCH_VERSATILE_PB +versatileab arm arm926ejs versatile armltd versatile versatile:ARCH_VERSATILE_AB aspenite arm arm926ejs - Marvell armada100 afeb9260 arm arm926ejs - - at91 at91cap9adk arm arm926ejs - atmel at91 diff --git a/include/configs/versatile.h b/include/configs/versatile.h index db6896584a5..32cee824bb6 100644 --- a/include/configs/versatile.h +++ b/include/configs/versatile.h @@ -74,6 +74,7 @@ /* * Size of malloc() pool */ +#define CONFIG_ENV_SIZE 8192 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) /* @@ -168,9 +169,26 @@ #define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ #define PHYS_FLASH_SIZE 0x04000000 /* 64MB */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x00800000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x000FFFFF +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_GBL_DATA_OFFSET) + +#define CONFIG_BOARD_EARLY_INIT_F + /*----------------------------------------------------------------------- * FLASH and environment organization */ +#ifdef CONFIG_ARCH_VERSATILE_QEMU +#define CONFIG_SYS_TEXT_BASE 0x10000 +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_MONITOR_LEN 0x80000 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000000 /* * Use the CFI flash driver for ease of use */ @@ -222,7 +240,6 @@ /* The ARM Boot Monitor is shipped in the lowest sector of flash */ #define FLASH_TOP (CONFIG_SYS_FLASH_BASE + PHYS_FLASH_SIZE) -#define CONFIG_ENV_SIZE 8192 #define CONFIG_ENV_ADDR (FLASH_TOP - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_MONITOR_BASE (CONFIG_ENV_ADDR - CONFIG_SYS_MONITOR_LEN) @@ -230,4 +247,6 @@ #define CONFIG_SYS_FLASH_PROTECTION /* The devices have real protection */ #define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ +#endif + #endif /* __CONFIG_H */ -- cgit v1.3.1 From a39fcfb24be1520859af038971f1eb1b5e06e927 Mon Sep 17 00:00:00 2001 From: Shiraz Hashim Date: Sat, 11 Jun 2011 21:32:57 +0000 Subject: spear: fix build errors for spear3xx/spear600 platforms Signed-off-by: Shiraz Hashim Acked-by: Vipin Kumar --- board/spear/common/spr_misc.c | 10 +++++++--- include/configs/spear-common.h | 12 ++++++++++++ 2 files changed, 19 insertions(+), 3 deletions(-) (limited to 'board') diff --git a/board/spear/common/spr_misc.c b/board/spear/common/spr_misc.c index 0562222ac82..0812c20b8c8 100644 --- a/board/spear/common/spr_misc.c +++ b/board/spear/common/spr_misc.c @@ -46,9 +46,7 @@ int dram_init(void) struct xloader_table_1_2 *table_1_2; struct chip_data *chip = &chip_data; - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = get_ram_size(PHYS_SDRAM_1, - PHYS_SDRAM_1_MAXSIZE); + gd->ram_size = get_ram_size(PHYS_SDRAM_1, PHYS_SDRAM_1_MAXSIZE); if (XLOADER_TABLE_VERSION_1_1 == xloader_tb->table_version) { table_1_1 = &xloader_tb->table.table_1_1; @@ -66,6 +64,12 @@ int dram_init(void) return 0; } +void dram_init_banksize(void) +{ + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = gd->ram_size; +} + int misc_init_r(void) { #if defined(CONFIG_CMD_NET) diff --git a/include/configs/spear-common.h b/include/configs/spear-common.h index 4e5bdea369a..55d19b5ce3f 100644 --- a/include/configs/spear-common.h +++ b/include/configs/spear-common.h @@ -86,6 +86,8 @@ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* NAND FLASH Configuration */ +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS #define CONFIG_NAND_SPEAR 1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 @@ -209,4 +211,14 @@ #define PHYS_SDRAM_1 0x00000000 #define PHYS_SDRAM_1_MAXSIZE 0x40000000 +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xD2800000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + #endif -- cgit v1.3.1 From 26749582d5c168dba72e3b11e84873e252b6b567 Mon Sep 17 00:00:00 2001 From: Ajay Bhargav <[ajay.bhargav@einfochips.com]> Date: Thu, 4 Aug 2011 21:26:02 +0530 Subject: Armada100: Add Board Support for Marvell GuruPlug-Display This patch adds basic board support with DRAM and UART functionality Signed-off-by: Prafulla Wadaskar Signed-off-by: Ajay Bhargav Acked-by: Tanmay Upadhyay --- MAINTAINERS | 4 ++ board/Marvell/gplugd/Makefile | 57 ++++++++++++++++++++++++++++ board/Marvell/gplugd/gplugd.c | 62 ++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/gplugd.h | 87 +++++++++++++++++++++++++++++++++++++++++++ 5 files changed, 211 insertions(+) create mode 100644 board/Marvell/gplugd/Makefile create mode 100644 board/Marvell/gplugd/gplugd.c create mode 100644 include/configs/gplugd.h (limited to 'board') diff --git a/MAINTAINERS b/MAINTAINERS index fd4181f072a..94e7da48b40 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -593,6 +593,10 @@ Eric Benard cpu9260 ARM926EJS (AT91SAM9260 SoC) cpu9G20 ARM926EJS (AT91SAM9G20 SoC) +Ajay Bhargav + + gplugd ARM926EJS (ARMADA100 88AP168 SoC) + Rishi Bhattacharya omap5912osk ARM926EJS diff --git a/board/Marvell/gplugd/Makefile b/board/Marvell/gplugd/Makefile new file mode 100644 index 00000000000..2d8bba0e389 --- /dev/null +++ b/board/Marvell/gplugd/Makefile @@ -0,0 +1,57 @@ +# +# (C) Copyright 2011 +# eInfochips Ltd. +# Written-by: Ajay Bhargav +# +# Based on Aspenite: +# (C) Copyright 2010 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# Contributor: Mahavir Jain +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := gplugd.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c new file mode 100644 index 00000000000..dc7d89d82d0 --- /dev/null +++ b/board/Marvell/gplugd/gplugd.c @@ -0,0 +1,62 @@ +/* + * (C) Copyright 2011 + * eInfochips Ltd. + * Written-by: Ajay Bhargav + * + * Based on Aspenite: + * (C) Copyright 2010 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * Contributor: Mahavir Jain + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + u32 mfp_cfg[] = { + /* I2C */ + MFP105_CI2C_SDA, + MFP106_CI2C_SCL, + + /* Enable Console on UART3 */ + MFPO8_UART3_TXD, + MFPO9_UART3_RXD, + MFP_EOC /*End of configuration*/ + }; + /* configure MFP's */ + mfp_config(mfp_cfg); + return 0; +} + +int board_init(void) +{ + /* arch number of Board */ + gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD; + /* adress of boot parameters */ + gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100; + return 0; +} diff --git a/boards.cfg b/boards.cfg index 3fe7d1bc6ad..6827cf31764 100644 --- a/boards.cfg +++ b/boards.cfg @@ -75,6 +75,7 @@ versatileqemu arm arm926ejs versatile armltd versatilepb arm arm926ejs versatile armltd versatile versatile:ARCH_VERSATILE_PB versatileab arm arm926ejs versatile armltd versatile versatile:ARCH_VERSATILE_AB aspenite arm arm926ejs - Marvell armada100 +gplugd arm arm926ejs - Marvell armada100 afeb9260 arm arm926ejs - - at91 at91cap9adk arm arm926ejs - atmel at91 at91sam9260ek_nandflash arm arm926ejs at91sam9260ek atmel at91 at91sam9260ek:AT91SAM9260,SYS_USE_NANDFLASH diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h new file mode 100644 index 00000000000..cc14f49966d --- /dev/null +++ b/include/configs/gplugd.h @@ -0,0 +1,87 @@ +/* + * (C) Copyright 2011 + * eInfochips Ltd. + * Written-by: Ajay Bhargav + * + * Based on Aspenite: + * (C) Copyright 2010 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * Contributor: Mahavir Jain + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +#ifndef __CONFIG_GPLUGD_H +#define __CONFIG_GPLUGD_H + +/* + * Version number information + */ +#define CONFIG_IDENT_STRING "\nMarvell-gplugD" + +/* + * High Level Configuration Options + */ +#define CONFIG_SHEEVA_88SV331xV5 1 /* CPU Core subversion */ +#define CONFIG_ARMADA100 1 /* SOC Family Name */ +#define CONFIG_ARMADA168 1 /* SOC Used on this Board */ +#define CONFIG_MACH_SHEEVAD /* Machine type */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ + +#define CONFIG_SYS_TEXT_BASE 0x00f00000 + +/* + * There is no internal RAM in ARMADA100, using DRAM + * TBD: dcache to be used for this + */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - 0x00200000) +#define CONFIG_NR_DRAM_BANKS_MAX 2 + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#include +#define CONFIG_CMD_I2C +#define CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" +#undef CONFIG_ARCH_MISC_INIT + +#ifdef CONFIG_SYS_NS16550_COM1 +#undef CONFIG_SYS_NS16550_COM1 +#endif /* CONFIG_SYS_NS16550_COM1 */ + +#define CONFIG_SYS_NS16550_COM1 ARMD1_UART3_BASE + +/* + * Environment variables configurations + */ +#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ +#define CONFIG_ENV_SIZE 0x20000 /* 64k */ + +#endif /* __CONFIG_GPLUGD_H */ -- cgit v1.3.1