From 466fff1a7bb5fe764a06450626f6098219f446b8 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 25 Jun 2007 15:57:39 +0200 Subject: ppc4xx: Add pci_pre_init() for 405 boards This patch removes the CFG_PCI_PRE_INIT option completely, since it's not needed anymore with the patch from Matthias Fuchs with the "weak" pci_pre_init() implementation. Signed-off-by: Stefan Roese --- doc/README.ppc440 | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) (limited to 'doc') diff --git a/doc/README.ppc440 b/doc/README.ppc440 index 08f34f589fa..2e04abacc8c 100644 --- a/doc/README.ppc440 +++ b/doc/README.ppc440 @@ -146,12 +146,13 @@ that maps in a single PCI I/O space and PCI memory space. The I/O space begins at PCI I/O address 0 and the PCI memory space is 256 MB starting at PCI address CFG_PCI_TARGBASE. After the pci_controller structure is initialized, the cpu-specific code will -call the routine pci_pre_init() if the CFG_PCI_PRE_INIT flag is -defined. This routine is implemented by board-specific code & is where -the board can over-ride/extend the default pci_controller structure -settings and do other pre-initialization tasks. If pci_pre_init() -returns a value of zero, PCI initialization is aborted; otherwise the -controller structure is registered and initialization continues. +call the routine pci_pre_init(). This routine is implemented by +board-specific code & is where the board can over-ride/extend the +default pci_controller structure settings and exspecially provide +a routine to map the PCI interrupts and do other pre-initialization +tasks. If pci_pre_init() returns a value of zero, PCI initialization +is aborted; otherwise the controller structure is registered and +initialization continues. The default 440GP PCI target configuration is minimal -- it assumes that the strapping registers are set as necessary. Since the strapping bits -- cgit v1.3.1 From 96e1d75be8193ca79e4215a368bf9d7f2362450f Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Wed, 11 Jul 2007 18:39:11 +0200 Subject: [PCS440EP] - Show on the DIAG LEDs, if the SHA1 check failed - now the Flash ST M29W040B is supported (not tested) - fix the "led" command - fix compile error, if BUILD_DIR is used Signed-off-by: Heiko Schocher --- Makefile | 2 +- board/pcs440ep/flash.c | 11 +++++++++ board/pcs440ep/pcs440ep.c | 37 ++++++++++++++++++++++-------- doc/README.sha1 | 57 ++++++++++++++++++++++++++++++++++++++++++++++ include/configs/pcs440ep.h | 8 +++---- 5 files changed, 101 insertions(+), 14 deletions(-) create mode 100644 doc/README.sha1 (limited to 'doc') diff --git a/Makefile b/Makefile index 47e4e670abd..c45700e08d6 100644 --- a/Makefile +++ b/Makefile @@ -268,7 +268,7 @@ $(obj)u-boot.img: $(obj)u-boot.bin -d $< $@ $(obj)u-boot.sha1: $(obj)u-boot.bin - ./tools/ubsha1 $(obj)u-boot.bin + $(obj)./tools/ubsha1 $(obj)u-boot.bin $(obj)u-boot.dis: $(obj)u-boot $(OBJDUMP) -d $< > $@ diff --git a/board/pcs440ep/flash.c b/board/pcs440ep/flash.c index 70014407c6e..c5a62e25436 100644 --- a/board/pcs440ep/flash.c +++ b/board/pcs440ep/flash.c @@ -82,6 +82,7 @@ void flash_print_info(flash_info_t *info) case FLASH_MAN_AMD: printf ("AMD "); break; case FLASH_MAN_FUJ: printf ("FUJITSU "); break; case FLASH_MAN_SST: printf ("SST "); break; + case FLASH_MAN_STM: printf ("ST Micro"); break; case FLASH_MAN_EXCEL: printf ("Excel Semiconductor "); break; case FLASH_MAN_MX: printf ("MXIC "); break; default: printf ("Unknown Vendor "); break; @@ -118,6 +119,8 @@ void flash_print_info(flash_info_t *info) break; case FLASH_SST040: printf ("SST39LF/VF040 (4 Mbit, uniform sector size)\n"); break; + case STM_ID_M29W040B: printf ("ST Micro M29W040B (4 Mbit, uniform sector size)\n"); + break; default: printf ("Unknown Chip Type\n"); break; } @@ -193,6 +196,9 @@ static ulong flash_get_size(vu_long *addr, flash_info_t *info) case (CFG_FLASH_WORD_SIZE)SST_MANUFACT: info->flash_id = FLASH_MAN_SST; break; + case (CFG_FLASH_WORD_SIZE)STM_MANUFACT: + info->flash_id = FLASH_MAN_STM; + break; case (CFG_FLASH_WORD_SIZE)EXCEL_MANUFACT: info->flash_id = FLASH_MAN_EXCEL; break; @@ -226,6 +232,11 @@ static ulong flash_get_size(vu_long *addr, flash_info_t *info) info->sector_count = 8; info->size = 0x0080000; /* => 0.5 MB */ break; + case (CFG_FLASH_WORD_SIZE)STM_ID_M29W040B: + info->flash_id += FLASH_AM040; + info->sector_count = 8; + info->size = 0x0080000; /* => 0,5 MB */ + break; case (CFG_FLASH_WORD_SIZE)AMD_ID_LV800T: info->flash_id += FLASH_AM800T; diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c index ada6b82c927..0e34a76cb9f 100644 --- a/board/pcs440ep/pcs440ep.c +++ b/board/pcs440ep/pcs440ep.c @@ -85,8 +85,9 @@ static void status_led_blink (void) /* set all LED which are on, to state BLINKING */ for (i = 0; i < 4; i++) { - if (val & 0x08) status_led_set (i, STATUS_LED_BLINKING); - val = val << 1; + if (val & 0x01) status_led_set (3 - i, STATUS_LED_BLINKING); + else status_led_set (3 - i, STATUS_LED_OFF); + val = val >> 1; } } @@ -113,12 +114,14 @@ void show_boot_progress (int val) status_led_set (1, STATUS_LED_ON); status_led_set (2, STATUS_LED_ON); break; +#if 0 case 64: /* starting Ethernet configuration */ status_led_set (0, STATUS_LED_OFF); status_led_set (1, STATUS_LED_OFF); status_led_set (2, STATUS_LED_ON); break; +#endif case 80: /* loading Image */ status_led_set (0, STATUS_LED_ON); @@ -404,6 +407,9 @@ static void pcs440ep_checksha1 (void) int ret; char *cs_test; + status_led_set (0, STATUS_LED_OFF); + status_led_set (1, STATUS_LED_OFF); + status_led_set (2, STATUS_LED_ON); ret = pcs440ep_sha1 (1); if (ret == 0) return; @@ -751,28 +757,41 @@ void hw_watchdog_reset(void) ************************************************************************/ int do_led (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { - int rcode = 0; + int rcode = 0, i; ulong pattern = 0; - pattern = simple_strtoul (argv[1], NULL, 10); - if (pattern > 200) { + pattern = simple_strtoul (argv[1], NULL, 16); + if (pattern > 0x400) { + int val = GET_LEDS; + printf ("led: %x\n", val); + return rcode; + } + if (pattern > 0x200) { status_led_blink (); hang (); return rcode; } - if (pattern > 100) { + if (pattern > 0x100) { status_led_blink (); return rcode; } pattern &= 0x0f; - set_leds (pattern); + for (i = 0; i < 4; i++) { + if (pattern & 0x01) status_led_set (i, STATUS_LED_ON); + else status_led_set (i, STATUS_LED_OFF); + pattern = pattern >> 1; + } return rcode; } U_BOOT_CMD( led, 2, 1, do_led, - "led - set the led\n", - NULL + "led [bitmask] - set the DIAG-LED\n", + "[bitmask] 0x01 = DIAG 1 on\n" + " 0x02 = DIAG 2 on\n" + " 0x04 = DIAG 3 on\n" + " 0x08 = DIAG 4 on\n" + " > 0x100 set the LED, who are on, to state blinking\n" ); #if defined(CONFIG_SHA1_CHECK_UB_IMG) diff --git a/doc/README.sha1 b/doc/README.sha1 new file mode 100644 index 00000000000..92dc8fffaea --- /dev/null +++ b/doc/README.sha1 @@ -0,0 +1,57 @@ +SHA1 usage: +----------- + +In the U-Boot Image for the pcs440ep board is a SHA1 checksum integrated. +This SHA1 sum is used, to check, if the U-Boot Image in Flash is not +corrupted. + +The following command is available: + +=> help sha1 +sha1 address len [addr] calculate the SHA1 sum [save at addr] + -p calculate the SHA1 sum from the U-Boot image in flash and print + -c check the U-Boot image in flash + +"sha1 -p" + calculates and prints the SHA1 sum, from the Image stored in Flash + +"sha1 -c" + check, if the SHA1 sum from the Image stored in Flash is correct + + +It is possible to calculate a SHA1 checksum from a memoryrange with: + +"sha1 address len" + +If you want to store a new Image in Flash for the pcs440ep board, +which has no SHA1 sum, you can do the following: + +a) cp the new Image on a position in RAM (here 0x300000) + (for this example we use the Image from Flash, stored at 0xfffa0000 and + 0x60000 Bytes long) + +"cp.b fffa0000 300000 60000" + +b) Initialize the SHA1 sum in the Image with 0x00 + The SHA1 sum is stored in Flash at: + CFG_MONITOR_BASE + CFG_MONITOR_LEN + SHA1_SUM_POS + for the pcs440ep Flash: 0xfffa0000 + 0x60000 + -0x20 + = 0xffffffe0 + for the example in RAM: 0x300000 + 0x60000 + -0x20 + = 0x35ffe0 + + note: a SHA1 checksum is 20 bytes long. + +"mw.b 35ffe0 0 14" + +c) now calculate the SHA1 sum from the memoryrange and write + the calculated checksum at the right place: + +"sha1 300000 60000 35ffe0" + +Now you have a U-Boot-Image for the pcs440ep board with the correct SHA1 sum. + +If you do a "./MAKEALL pcs440ep" or a "make all" to get the U-Boot image, +the correct SHA1 sum will be automagically included in the U-Boot image. + +Heiko Schocher, 11 Jul 2007 diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 69d97d66ea1..5ee97c12794 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -197,16 +197,16 @@ #define CONFIG_STATUS_LED 1 /* Status LED enabled */ #define CONFIG_BOARD_SPECIFIC_LED 1 -#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */ +#define STATUS_LED_BIT 0x08 /* DIAG1 is on GPIO_PPC_1 */ #define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ #define STATUS_LED_STATE STATUS_LED_OFF -#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */ +#define STATUS_LED_BIT1 0x04 /* DIAG2 is on GPIO_PPC_2 */ #define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ #define STATUS_LED_STATE1 STATUS_LED_ON -#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */ +#define STATUS_LED_BIT2 0x02 /* DIAG3 is on GPIO_PPC_3 */ #define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ #define STATUS_LED_STATE2 STATUS_LED_OFF -#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */ +#define STATUS_LED_BIT3 0x01 /* DIAG4 is on GPIO_PPC_4 */ #define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ #define STATUS_LED_STATE3 STATUS_LED_OFF -- cgit v1.3.1 From 239f05ee4dd4cfe0b50f251b533dcebe9e67c360 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Thu, 12 Jul 2007 01:45:34 +0200 Subject: Update CHANGELOG, minor coding style cleanup. Signed-off-by: Wolfgang Denk --- CHANGELOG | 28 ++++++++++++++++++++++++++++ cpu/ppc4xx/44x_spd_ddr.c | 2 +- doc/README.sha1 | 10 +++++----- 3 files changed, 34 insertions(+), 6 deletions(-) (limited to 'doc') diff --git a/CHANGELOG b/CHANGELOG index 2397191fc97..fef629ad468 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,3 +1,31 @@ +commit fa1df308926a6f70e3504c57514ef27ac31fd13a +Author: Bartlomiej Sieka +Date: Wed Jul 11 20:11:07 2007 +0200 + + CM1.QP1: Support for the Schindler CM1.QP1 board. + + Signed-off-by: Piotr Kruszynski + Signed-off-by: Bartlomiej Sieka + +commit 96e1d75be8193ca79e4215a368bf9d7f2362450f +Author: Heiko Schocher +Date: Wed Jul 11 18:39:11 2007 +0200 + + [PCS440EP] - Show on the DIAG LEDs, if the SHA1 check failed + - now the Flash ST M29W040B is supported (not tested) + - fix the "led" command + - fix compile error, if BUILD_DIR is used + + Signed-off-by: Heiko Schocher + +commit 4ef218f6fdf8d747f4589da5252b004e7d2c2876 +Author: Wolfgang Denk +Date: Tue Jul 10 00:01:28 2007 +0200 + + Coding style cleanup; update CHANGELOG. + + Signed-off-by: Wolfgang Denk + commit f1152f8c28db4a22087c21c618a3f7baa48e9a4f Author: Wolfgang Denk Date: Fri Jul 6 02:50:19 2007 +0200 diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index 8c18d0f4e21..6d6fba1802d 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -1017,7 +1017,7 @@ static int short_mem_test(void) */ for (i = 0; i < NUMMEMTESTS; i++) { for (j = 0; j < NUMMEMWORDS; j++) { -//printf("bank enabled base:%x\n", &membase[j]); + /* printf("bank enabled base:%x\n", &membase[j]); */ membase[j] = test[i][j]; ppcDcbf((unsigned long)&(membase[j])); } diff --git a/doc/README.sha1 b/doc/README.sha1 index 92dc8fffaea..7992f7fb4c8 100644 --- a/doc/README.sha1 +++ b/doc/README.sha1 @@ -34,11 +34,11 @@ a) cp the new Image on a position in RAM (here 0x300000) b) Initialize the SHA1 sum in the Image with 0x00 The SHA1 sum is stored in Flash at: - CFG_MONITOR_BASE + CFG_MONITOR_LEN + SHA1_SUM_POS - for the pcs440ep Flash: 0xfffa0000 + 0x60000 + -0x20 - = 0xffffffe0 - for the example in RAM: 0x300000 + 0x60000 + -0x20 - = 0x35ffe0 + CFG_MONITOR_BASE + CFG_MONITOR_LEN + SHA1_SUM_POS + for the pcs440ep Flash: 0xfffa0000 + 0x60000 + -0x20 + = 0xffffffe0 + for the example in RAM: 0x300000 + 0x60000 + -0x20 + = 0x35ffe0 note: a SHA1 checksum is 20 bytes long. -- cgit v1.3.1