From d11fec5015334deb2010e36ce00bb118cc5429a5 Mon Sep 17 00:00:00 2001 From: Haiying Wang Date: Fri, 26 May 2006 10:24:48 -0500 Subject: Add first draft of the MPC8641HPCN doc/README. Signed-off-by: Jon Loeliger --- doc/README.mpc8641hpcn | 123 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 123 insertions(+) create mode 100644 doc/README.mpc8641hpcn (limited to 'doc') diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn new file mode 100644 index 00000000000..907a911ed1a --- /dev/null +++ b/doc/README.mpc8641hpcn @@ -0,0 +1,123 @@ +Freescale MPC8641HPCN board +=========================== + +Created 05/24/2006 Haiying Wang +------------------------------- + +1. Building U-Boot +------------------ +The 86xx HPCN code base is known to compile using: + Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 + + $ make MPC8641HPCN_config + Configuring for MPC8641HPCN board... + + $ make + + +2. Switch and Jumper Setting +---------------------------- +Jumpers: + J14 Pins 1-2 (near plcc32 socket) + +Switches: + SW1(1-5) = 01100 CFG_COREPLL = 01000 :: CORE = 2:1 + 01100 :: CORE = 2.5:1 + 10000 :: CORE = 3:1 + 11100 :: CORE = 3.5:1 + 10100 :: CORE = 4:1 + 01110 :: CORE = 4.5:1 + SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz + 001 :: SYSCLK = 40MHz + + SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X + 0100 :: 4X + 0110 :: 6X + 1000 :: 8X + 1010 :: 10X + 1100 :: 12X + 1110 :: 14X + 0000 :: 16X + SW2(5-8) = 1110 CFG_BOOTLOC = 1110 :: boot 16-bit localbus + + SW3(1-7) = 0011000 CFG_VID = 0011000 :: VCORE = 1.2V + 0100000 :: VCORE = 1.11V + SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V + 1 :: VCC_PLAT = 1.0V + + SW4(1-2) = 11 CFG_HOSTMODE = 11 :: both prots host/root + SW4(3-4) = 11 CFG_BOOTSEQ = 11 :: no boot seq + SW4(5-8) = 0011 CFG_IOPORT = 0011 :: both PEX + + SW5(1) = 1 CFG_FLASHMAP = 1 :: boot from flash + 0 :: boot from PromJet + SW5(2) = 1 CFG_FLASHBANK = 1 :: swap upper/lower + halves (virtual banks) + 0 :: normal + SW5(3) = 0 CFG_FLASHWP = 0 :: not protected + SW5(4) = 0 CFG_PORTDIV = 1 :: 2:1 for PD4 + 1:1 for PD6 + SW5(5-6) = 11 CFG_PIXISOPT = 11 :: s/w determined + SW5(7-8) = 11 CFG_LADOPT = 11 :: s/w determined + + SW6(1) = 1 CFG_CPUBOOT = 1 :: no boot holdoff + SW6(2) = 1 CFG_BOOTADDR = 1 :: no traslation + SW6(3-5) = 000 CFG_REFCLKSEL = 000 :: 100MHZ + SW6(6) = 1 CFG_SERROM_ADDR= 1 :: + SW6(7) = 1 CFG_MEMDEBUG = 1 :: + SW6(8) = 1 CFG_DDRDEBUG = 1 :: + + SW8(1) = 1 ACZ_SYNC = 1 :: 48MHz on TP49 + SW8(2) = 1 ACB_SYNC = 1 :: THRMTRIP disabled + SW8(3) = 1 ACZ_SDOUT = 1 :: p4 mode + SW8(4) = 1 ACB_SDOUT = 1 :: PATA freq. = 133MHz + SW8(5) = 0 SUSLED = 0 :: SouthBridge Mode + SW8(6) = 0 SPREAD = 0 :: REFCLK SSCG Disabled + SW8(7) = 1 ACPWR = 1 :: non-battery + SW8(8) = 0 CFG_IDWP = 0 :: write enable + + +3. Flash U-Boot +--------------- +The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves. +It is possible to use either half to boot using u-boot. Switch 5 bit 2 +is used for this purpose. + +0xFF800000 to 0xFFBFFFFF - 4MB +0xFFC00000 to 0xFFFFFFFF - 4MB +When this bit is 0, U-Boot is at 0xFFF00000. +When this bit is 1, U-Boot is at 0xFFB00000. + +Use the above mentioned flash commands to program the other half, and +use switch 5, bit 2 to alternate between the halves. Note: The booting +version of U-Boot will always be at 0xFFF00000. + +To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF): + + tftp 1000000 u-boot.bin + protect off all + erase fff00000 ffffffff + cp.b 1000000 fff00100 80000 + +To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): + + tftp 1000000 u-boot.bin + erase ffb00000 ffbfffff + cp.b 1000000 ffb00100 80000 + + +4. Memory Map +------------- + + Memory Range Device Size + ------------ ------ ---- + 0x0000_0000 0x7fff_ffff DDR 2G + 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M + 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M + 0xf800_0000 0xf80f_ffff CCSR 1M + 0xf810_0000 0xf81f_ffff PIXIS 1M + 0xf840_0000 0xf840_3fff Stack space 32K + 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 512M + 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 512M + 0xfe00_0000 0xfeff_ffff Flash(alternate)16M + 0xff00_0000 0xffff_ffff Flash(boot bank)16M -- cgit v1.3.1 From 9cb3e8816ae4d854e7dc22128c3eea3d70bb982c Mon Sep 17 00:00:00 2001 From: Haiying Wang Date: Fri, 28 Jul 2006 12:41:41 -0400 Subject: Change the space size of PEX IO in README --- doc/README.mpc8641hpcn | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'doc') diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn index 907a911ed1a..8ea0b1e9eeb 100644 --- a/doc/README.mpc8641hpcn +++ b/doc/README.mpc8641hpcn @@ -117,7 +117,7 @@ To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): 0xf800_0000 0xf80f_ffff CCSR 1M 0xf810_0000 0xf81f_ffff PIXIS 1M 0xf840_0000 0xf840_3fff Stack space 32K - 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 512M - 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 512M + 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M + 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M 0xfe00_0000 0xfeff_ffff Flash(alternate)16M 0xff00_0000 0xffff_ffff Flash(boot bank)16M -- cgit v1.3.1 From 34c3c0e01dbf1f8cc2bd08de92f2b89ba84921eb Mon Sep 17 00:00:00 2001 From: Matthew McClintock Date: Wed, 28 Jun 2006 10:47:03 -0500 Subject: * Switched default PCI speed for 8540 ADS back to 33MHz * Added comments and a printf to warn that PCI-X won't work at 33MHz Patch by Andy Fleming 17-Mar-2006 Signed-off-by: Andy Fleming --- cpu/mpc85xx/pci.c | 3 +++ doc/README.mpc85xxads | 3 +++ include/configs/MPC8540ADS.h | 6 +++++- 3 files changed, 11 insertions(+), 1 deletion(-) (limited to 'doc') diff --git a/cpu/mpc85xx/pci.c b/cpu/mpc85xx/pci.c index ca11bce22ea..cfb7dcdc895 100644 --- a/cpu/mpc85xx/pci.c +++ b/cpu/mpc85xx/pci.c @@ -72,6 +72,9 @@ pci_mpc85xx_init(struct pci_controller *board_hose) if (!(gur->pordevsr & PORDEVSR_PCI)) { /* PCI-X init */ + if (CONFIG_SYS_CLK_FREQ < 66000000) + printf("PCI-X will only work at 66 MHz\n"); + reg16 = PCI_X_CMD_MAX_SPLIT | PCI_X_CMD_MAX_READ | PCI_X_CMD_ERO | PCI_X_CMD_DPERR_E; pci_hose_write_config_word(hose, dev, PCIX_COMMAND, reg16); diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads index f0cf782a8fc..ae8202bdd17 100644 --- a/doc/README.mpc85xxads +++ b/doc/README.mpc85xxads @@ -100,6 +100,9 @@ Updated 13-July-2004 Jon Loeliger SW7[1:4] = 0101 = 5 => 5 x 66 = 330 CCB Sysclk SW7[5:6] = 01 => 5:2 x 330 = 825 Core clock + In order to use PCI-X (only in the first PCI slot. The one with + the RIO connector), you need to set SW1[4] (config) to 1 (off). + Also, configure the board to run PCI at 66 MHz. 2. MEMORY MAP TO WORK WITH LINUX KERNEL diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 81ee945d499..8e4d2c95a44 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -68,10 +68,14 @@ * The board, however, can run at 66MHz. In any event, this value * must match the settings of some switches. Details can be found * in the README.mpc85xxads. + * + * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to + * 33MHz to accommodate, based on a PCI pin. + * Note that PCI-X won't work at 33MHz. */ #ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_SYS_CLK_FREQ 33000000 #endif -- cgit v1.3.1 From 887e2ec9ecf49366a60a49b32b73825804909865 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 7 Sep 2006 11:51:23 +0200 Subject: Add support for AMCC Sequoia PPC440EPx eval board - Add support for PPC440EPx & PPC440GRx - Add support for PPC440EP(x)/GR(x) NAND controller in cpu/ppc4xx directory - Add NAND boot functionality for Sequoia board, please see doc/README.nand-boot-ppc440 for details - This Sequoia NAND image doesn't support environment in NAND for now. This will be added in a short while. Patch by Stefan Roese, 07 Sep 2006 --- CHANGELOG | 10 + MAINTAINERS | 1 + MAKEALL | 9 +- Makefile | 39 ++- board/amcc/sequoia/Makefile | 52 +++ board/amcc/sequoia/config.mk | 41 +++ board/amcc/sequoia/init.S | 157 +++++++++ board/amcc/sequoia/sdram.c | 83 +++++ board/amcc/sequoia/sequoia.c | 552 ++++++++++++++++++++++++++++++ board/amcc/sequoia/sequoia.h | 67 ++++ board/amcc/sequoia/u-boot-nand.lds | 131 +++++++ board/amcc/sequoia/u-boot.lds | 145 ++++++++ common/cmd_bdinfo.c | 6 +- config.mk | 4 + cpu/ppc4xx/405gp_pci.c | 3 +- cpu/ppc4xx/4xx_enet.c | 184 ++++++++-- cpu/ppc4xx/Makefile | 2 +- cpu/ppc4xx/cpu.c | 109 +++++- cpu/ppc4xx/interrupts.c | 57 ++- cpu/ppc4xx/miiphy.c | 14 +- cpu/ppc4xx/ndfc.c | 173 ++++++++++ cpu/ppc4xx/serial.c | 263 +++++--------- cpu/ppc4xx/speed.c | 3 +- cpu/ppc4xx/start.S | 128 ++++++- cpu/ppc4xx/usb_ohci.c | 8 +- cpu/ppc4xx/usbdev.c | 20 +- cpu/ppc4xx/vecnum.h | 89 ++++- doc/README.nand-boot-ppc440 | 36 ++ dtt/lm75.c | 5 + include/405_mal.h | 2 +- include/440_i2c.h | 3 +- include/asm-ppc/processor.h | 4 + include/asm-ppc/u-boot.h | 3 +- include/configs/bamboo.h | 1 + include/configs/pcs440ep.h | 1 + include/configs/sequoia.h | 431 +++++++++++++++++++++++ include/configs/yellowstone.h | 1 + include/configs/yosemite.h | 1 + include/linux/mtd/compat.h | 2 + include/linux/mtd/ndfc.h | 67 ++++ include/ppc440.h | 609 +++++++++++++++++++++++++++++++-- include/ppc4xx_enet.h | 22 +- include/ppc_asm.tmpl | 2 +- lib_ppc/board.c | 12 +- nand_spl/board/amcc/sequoia/Makefile | 83 +++++ nand_spl/board/amcc/sequoia/config.mk | 49 +++ nand_spl/board/amcc/sequoia/u-boot.lds | 65 ++++ nand_spl/nand_boot.c | 178 ++++++++++ 48 files changed, 3606 insertions(+), 321 deletions(-) create mode 100644 board/amcc/sequoia/Makefile create mode 100644 board/amcc/sequoia/config.mk create mode 100644 board/amcc/sequoia/init.S create mode 100644 board/amcc/sequoia/sdram.c create mode 100644 board/amcc/sequoia/sequoia.c create mode 100644 board/amcc/sequoia/sequoia.h create mode 100644 board/amcc/sequoia/u-boot-nand.lds create mode 100644 board/amcc/sequoia/u-boot.lds create mode 100644 cpu/ppc4xx/ndfc.c create mode 100644 doc/README.nand-boot-ppc440 create mode 100644 include/configs/sequoia.h create mode 100644 include/linux/mtd/ndfc.h create mode 100644 nand_spl/board/amcc/sequoia/Makefile create mode 100644 nand_spl/board/amcc/sequoia/config.mk create mode 100644 nand_spl/board/amcc/sequoia/u-boot.lds create mode 100644 nand_spl/nand_boot.c (limited to 'doc') diff --git a/CHANGELOG b/CHANGELOG index 3c42d93fe84..576cd7fb861 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,16 @@ Changes since U-Boot 1.1.4: ====================================================================== +* Add support for AMCC Sequoia PPC440EPx eval board + - Add support for PPC440EPx & PPC440GRx + - Add support for PPC440EP(x)/GR(x) NAND controller + in cpu/ppc4xx directory + - Add NAND boot functionality for Sequoia board, + please see doc/README.nand-boot-ppc440 for details + - This Sequoia NAND image doesn't support environment + in NAND for now. This will be added in a short while. + Patch by Stefan Roese, 07 Sep 2006 + * Fix mkimage -l bug with multifile images on 64bit platforms Patch by David Updegraff, 06 Sep 2006 diff --git a/MAINTAINERS b/MAINTAINERS index 0c4cfb43cf4..42627196f86 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -285,6 +285,7 @@ Stefan Roese ocotea PPC440GX p3p440 PPC440GP pcs440ep PPC440EP + sequoia PPC440EPx sycamore PPC405GPr walnut PPC405GP yellowstone PPC440GR diff --git a/MAKEALL b/MAKEALL index d2f86d3ac8a..8039f3d7082 100755 --- a/MAKEALL +++ b/MAKEALL @@ -13,7 +13,7 @@ if [ "${MAKEALL_LOGDIR}" ] ; then else LOG_DIR="LOG" fi - + if [ ! "${BUILD_DIR}" ] ; then BUILD_DIR="." fi @@ -85,9 +85,10 @@ LIST_4xx=" \ ML2 ml300 ocotea OCRTC \ ORSG p3p440 PCI405 pcs440ep \ PIP405 PLU405 PMC405 PPChameleonEVB \ - sbc405 VOH405 VOM405 W7OLMC \ - W7OLMG walnut WUH405 XPEDITE1K \ - yellowstone yosemite yucca bamboo \ + sbc405 sequoia sequoia_nand VOH405 \ + VOM405 W7OLMC W7OLMG walnut \ + WUH405 XPEDITE1K yellowstone yosemite \ + yucca bamboo \ " ######################################################################### diff --git a/Makefile b/Makefile index fc7b117e3fe..a63aaef15bc 100644 --- a/Makefile +++ b/Makefile @@ -48,7 +48,7 @@ VENDOR= # # U-boot build supports producing a object files to the separate external # directory. Two use cases are supported: -# +# # 1) Add O= to the make command line # 'make O=/tmp/build all' # @@ -59,12 +59,12 @@ VENDOR= # The second approach can also be used with a MAKEALL script # 'export BUILD_DIR=/tmp/build' # './MAKEALL' -# +# # Command line 'O=' setting overrides BUILD_DIR environent variable. -# +# # When none of the above methods is used the local build is performed and # the object files are placed in the source directory. -# +# ifdef O ifeq ("$(origin O)", "command line") @@ -101,7 +101,7 @@ src := $(SRCTREE)/ else obj := src := -endif +endif export obj src ######################################################################### @@ -214,13 +214,18 @@ SUBDIRS = tools \ post/cpu .PHONY : $(SUBDIRS) +ifeq ($(CONFIG_NAND_U_BOOT),y) +NAND_SPL = nand_spl +U_BOOT_NAND = $(obj)u-boot-nand.bin +endif + __OBJS := $(subst $(obj),,$(OBJS)) __LIBS := $(subst $(obj),,$(LIBS)) ######################################################################### ######################################################################### -ALL = $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map +ALL = $(obj)u-boot.srec $(obj)u-boot.bin $(obj)System.map $(U_BOOT_NAND) all: $(ALL) @@ -258,6 +263,12 @@ $(LIBS): $(SUBDIRS): $(MAKE) -C $@ all +$(NAND_SPL): version + $(MAKE) -C nand_spl all + +$(U_BOOT_NAND): $(NAND_SPL) $(obj)u-boot.bin + cat nand_spl/u-boot-spl-4k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin + version: @echo -n "#define U_BOOT_VERSION \"U-Boot " > $(VERSION_FILE); \ echo -n "$(U_BOOT_VERSION)" >> $(VERSION_FILE); \ @@ -309,7 +320,8 @@ endif ######################################################################### unconfig: - @rm -f $(obj)include/config.h $(obj)include/config.mk $(obj)board/*/config.tmp + @rm -f $(obj)include/config.h $(obj)include/config.mk \ + $(obj)board/*/config.tmp $(obj)board/*/*/config.tmp #======================================================================== # PowerPC @@ -1128,6 +1140,17 @@ PPChameleonEVB_HI_33_config: unconfig sbc405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx sbc405 +sequoia_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx sequoia amcc + +sequoia_nand_config: unconfig + @ln -s board/amcc/sequoia/Makefile nand_spl/Makefile + @echo "#define CONFIG_NAND_U_BOOT" >include/config.h + @echo "Compile NAND boot image for sequoia" + @$(MKCONFIG) -a sequoia ppc ppc4xx sequoia amcc + @echo "TEXT_BASE = 0x01000000" >board/amcc/sequoia/config.tmp + @echo "CONFIG_NAND_U_BOOT = y" >> include/config.mk + sycamore_config: unconfig @echo "Configuring for sycamore board as subset of walnut..." @$(MKCONFIG) -a walnut ppc ppc4xx walnut amcc @@ -2195,6 +2218,8 @@ clean: rm -f $(obj)board/trab/trab_fkt $(obj)board/voiceblue/eeprom rm -f $(obj)board/integratorap/u-boot.lds $(obj)board/integratorcp/u-boot.lds rm -f $(obj)include/bmp_logo.h + find nand_spl -lname "*" -print | xargs rm -f + rm -f nand_spl/u-boot-spl nand_spl/u-boot-spl.map clobber: clean find $(OBJTREE) -type f \( -name .depend \ diff --git a/board/amcc/sequoia/Makefile b/board/amcc/sequoia/Makefile new file mode 100644 index 00000000000..b29c04a0d9e --- /dev/null +++ b/board/amcc/sequoia/Makefile @@ -0,0 +1,52 @@ +# +# (C) Copyright 2002-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +include $(TOPDIR)/include/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o sdram.o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/amcc/sequoia/config.mk b/board/amcc/sequoia/config.mk new file mode 100644 index 00000000000..7713a72be85 --- /dev/null +++ b/board/amcc/sequoia/config.mk @@ -0,0 +1,41 @@ +# +# (C) Copyright 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# +# AMCC 440EPx Reference Platform (Sequoia) board +# + +sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp + +ifndef TEXT_BASE +TEXT_BASE = 0xFFFA0000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 +endif diff --git a/board/amcc/sequoia/init.S b/board/amcc/sequoia/init.S new file mode 100644 index 00000000000..3d4ac8543d5 --- /dev/null +++ b/board/amcc/sequoia/init.S @@ -0,0 +1,157 @@ +/* + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +/* General */ +#define TLB_VALID 0x00000200 +#define _256M 0x10000000 + +/* Supported page sizes */ + +#define SZ_1K 0x00000000 +#define SZ_4K 0x00000010 +#define SZ_16K 0x00000020 +#define SZ_64K 0x00000030 +#define SZ_256K 0x00000040 +#define SZ_1M 0x00000050 +#define SZ_8M 0x00000060 +#define SZ_16M 0x00000070 +#define SZ_256M 0x00000090 + +/* Storage attributes */ +#define SA_W 0x00000800 /* Write-through */ +#define SA_I 0x00000400 /* Caching inhibited */ +#define SA_M 0x00000200 /* Memory coherence */ +#define SA_G 0x00000100 /* Guarded */ +#define SA_E 0x00000080 /* Endian */ + +/* Access control */ +#define AC_X 0x00000024 /* Execute */ +#define AC_W 0x00000012 /* Write */ +#define AC_R 0x00000009 /* Read */ + +/* Some handy macros */ + +#define EPN(e) ((e) & 0xfffffc00) +#define TLB0(epn,sz) ( (EPN((epn)) | (sz) | TLB_VALID ) ) +#define TLB1(rpn,erpn) ( ((rpn)&0xfffffc00) | (erpn) ) +#define TLB2(a) ( (a)&0x00000fbf ) + +#define tlbtab_start\ + mflr r1 ;\ + bl 0f ; + +#define tlbtab_end\ + .long 0, 0, 0 ; \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + +#define tlbentry(epn,sz,rpn,erpn,attr)\ + .long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr) + + +/************************************************************************** + * TLB TABLE + * + * This table is used by the cpu boot code to setup the initial tlb + * entries. Rather than make broad assumptions in the cpu source tree, + * this table lets each board set things up however they like. + * + * Pointer to the table is returned in r1 + * + *************************************************************************/ + .section .bootpg,"ax" + .globl tlbtab + +tlbtab: + tlbtab_start + + /* + * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ +#ifndef CONFIG_NAND_SPL + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G ) +#else + tlbentry( CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 1, AC_R|AC_W|AC_X|SA_G ) +#endif + + /* TLB-entry for DDR SDRAM (Up to 2GB) */ + tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) + +#ifdef CFG_INIT_RAM_DCACHE + /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ + tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) +#endif + + /* TLB-entry for PCI Memory */ + tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I ) + tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I ) + + /* TLB-entry for EBC */ + tlbentry( CFG_BCSR_BASE, SZ_1K, CFG_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* TLB-entry for NAND */ + tlbentry( CFG_NAND_ADDR, SZ_1K, CFG_NAND_ADDR, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* TLB-entry for Internal Registers & OCM */ + tlbentry( 0xe0000000, SZ_16M, 0xe0000000, 0, AC_R|AC_W|AC_X|SA_I ) + + /*TLB-entry PCI registers*/ + tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* TLB-entry for peripherals */ + tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I) + + tlbtab_end + +#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) + /* + * For NAND booting the first TLB has to be reconfigured to full size + * and with caching disabled after running from RAM! + */ +#define TLB00 TLB0(CFG_BOOT_BASE_ADDR, SZ_256M) +#define TLB01 TLB1(CFG_BOOT_BASE_ADDR, 1) +#define TLB02 TLB2(AC_R|AC_W|AC_X|SA_G|SA_I) + + .globl reconfig_tlb0 +reconfig_tlb0: + sync + isync + addi r4,r0,0x0000 /* TLB entry #0 */ + lis r5,TLB00@h + ori r5,r5,TLB00@l + tlbwe r5,r4,0x0000 /* Save it out */ + lis r5,TLB01@h + ori r5,r5,TLB01@l + tlbwe r5,r4,0x0001 /* Save it out */ + lis r5,TLB02@h + ori r5,r5,TLB02@l + tlbwe r5,r4,0x0002 /* Save it out */ + sync + isync + blr +#endif diff --git a/board/amcc/sequoia/sdram.c b/board/amcc/sequoia/sdram.c new file mode 100644 index 00000000000..a62648bb5f4 --- /dev/null +++ b/board/amcc/sequoia/sdram.c @@ -0,0 +1,83 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/************************************************************************* + * + * initdram -- 440EPx's DDR controller is a DENALI Core + * + ************************************************************************/ +long int initdram (int board_type) +{ +#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) + volatile ulong val; + + mtsdram(DDR0_02, 0x00000000); + + /* + * Soft-reset SDRAM controller + */ + mtsdr(sdr_srst, SDR0_SRST0_DMC); + mtsdr(sdr_srst, 0x00000000); + + mtsdram(DDR0_00, 0x0000190A); + mtsdram(DDR0_01, 0x01000000); + mtsdram(DDR0_03, 0x02030602); + mtsdram(DDR0_04, 0x13030300); + mtsdram(DDR0_05, 0x0202050E); + mtsdram(DDR0_06, 0x0104C823); + mtsdram(DDR0_07, 0x000D0100); + mtsdram(DDR0_08, 0x02360001); + mtsdram(DDR0_09, 0x00011D5F); + mtsdram(DDR0_10, 0x00000300); + mtsdram(DDR0_11, 0x0027C800); + mtsdram(DDR0_12, 0x00000003); + mtsdram(DDR0_14, 0x00000000); + mtsdram(DDR0_17, 0x19000000); + mtsdram(DDR0_18, 0x19191919); + mtsdram(DDR0_19, 0x19191919); + mtsdram(DDR0_20, 0x0B0B0B0B); + mtsdram(DDR0_21, 0x0B0B0B0B); + mtsdram(DDR0_22, 0x00267F0B); + mtsdram(DDR0_23, 0x00000000); + mtsdram(DDR0_24, 0x01010002); + mtsdram(DDR0_26, 0x5B260181); + mtsdram(DDR0_27, 0x0000682B); + mtsdram(DDR0_28, 0x00000000); + mtsdram(DDR0_31, 0x00000000); + mtsdram(DDR0_42, 0x01000006); + mtsdram(DDR0_43, 0x050A0200); + mtsdram(DDR0_44, 0x00000005); + mtsdram(DDR0_02, 0x00000001); + + /* + * Wait for DCC master delay line to finish calibration + */ + mfsdram(DDR0_17, val); + while (((val >> 8) & 0x000007f) == 0) { + mfsdram(DDR0_17, val); + } +#endif /* #ifndef CONFIG_NAND_U_BOOT */ + + return (CFG_MBYTES_SDRAM << 20); +} diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c new file mode 100644 index 00000000000..95734b9c57c --- /dev/null +++ b/board/amcc/sequoia/sequoia.c @@ -0,0 +1,552 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include "sequoia.h" + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +int board_early_init_f(void) +{ + unsigned long sdr0_cust0; + unsigned long sdr0_pfc1, sdr0_pfc2; + register uint reg; + + mtdcr(ebccfga, xbcfg); + mtdcr(ebccfgd, 0xb8400000); + + /*-------------------------------------------------------------------- + * Setup the GPIO pins + *-------------------------------------------------------------------*/ + /* test-only: take GPIO init from pcs440ep ???? in config file */ + out32(GPIO0_OR, 0x00000000); + out32(GPIO0_TCR, 0x0000000f); + out32(GPIO0_OSRL, 0x50015400); + out32(GPIO0_OSRH, 0x550050aa); + out32(GPIO0_TSRL, 0x50015400); + out32(GPIO0_TSRH, 0x55005000); + out32(GPIO0_ISR1L, 0x50000000); + out32(GPIO0_ISR1H, 0x00000000); + out32(GPIO0_ISR2L, 0x00000000); + out32(GPIO0_ISR2H, 0x00000100); + out32(GPIO0_ISR3L, 0x00000000); + out32(GPIO0_ISR3H, 0x00000000); + + out32(GPIO1_OR, 0x00000000); + out32(GPIO1_TCR, 0xc2000000); + out32(GPIO1_OSRL, 0x5c280000); + out32(GPIO1_OSRH, 0x00000000); + out32(GPIO1_TSRL, 0x0c000000); + out32(GPIO1_TSRH, 0x00000000); + out32(GPIO1_ISR1L, 0x00005550); + out32(GPIO1_ISR1H, 0x00000000); + out32(GPIO1_ISR2L, 0x00050000); + out32(GPIO1_ISR2H, 0x00000000); + out32(GPIO1_ISR3L, 0x01400000); + out32(GPIO1_ISR3H, 0x00000000); + + /*-------------------------------------------------------------------- + * Setup the interrupt controller polarities, triggers, etc. + *-------------------------------------------------------------------*/ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + mtdcr(uic0er, 0x00000000); /* disable all */ + mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */ + mtdcr(uic0pr, 0xfffff7ff); /* per ref-board manual */ + mtdcr(uic0tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic0sr, 0xffffffff); /* clear all */ + + mtdcr(uic1sr, 0xffffffff); /* clear all */ + mtdcr(uic1er, 0x00000000); /* disable all */ + mtdcr(uic1cr, 0x00000000); /* all non-critical */ + mtdcr(uic1pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic1tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic1sr, 0xffffffff); /* clear all */ + + mtdcr(uic2sr, 0xffffffff); /* clear all */ + mtdcr(uic2er, 0x00000000); /* disable all */ + mtdcr(uic2cr, 0x00000000); /* all non-critical */ + mtdcr(uic2pr, 0xffffffff); /* per ref-board manual */ + mtdcr(uic2tr, 0x00000000); /* per ref-board manual */ + mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */ + mtdcr(uic2sr, 0xffffffff); /* clear all */ + + /* 50MHz tmrclk */ + *(unsigned char *)(CFG_BCSR_BASE | 0x04) = 0x00; + + /* clear write protects */ + *(unsigned char *)(CFG_BCSR_BASE | 0x07) = 0x00; + + /* enable Ethernet */ + *(unsigned char *)(CFG_BCSR_BASE | 0x08) = 0x00; + + /* enable USB device */ + *(unsigned char *)(CFG_BCSR_BASE | 0x09) = 0x20; + + /* select Ethernet pins */ + mfsdr(SDR0_PFC1, sdr0_pfc1); + sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) | SDR0_PFC1_SELECT_CONFIG_4; + mfsdr(SDR0_PFC2, sdr0_pfc2); + sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) | SDR0_PFC2_SELECT_CONFIG_4; + mtsdr(SDR0_PFC2, sdr0_pfc2); + mtsdr(SDR0_PFC1, sdr0_pfc1); + + /* PCI arbiter enabled */ + mfsdr(sdr_pci0, reg); + mtsdr(sdr_pci0, 0x80000000 | reg); + + /* setup NAND FLASH */ + mfsdr(SDR0_CUST0, sdr0_cust0); + sdr0_cust0 = SDR0_CUST0_MUX_NDFC_SEL | + SDR0_CUST0_NDFC_ENABLE | + SDR0_CUST0_NDFC_BW_8_BIT | + SDR0_CUST0_NDFC_ARE_MASK | + (0x80000000 >> (28 + CFG_NAND_CS)); + mtsdr(SDR0_CUST0, sdr0_cust0); + + return 0; +} + +/*---------------------------------------------------------------------------+ + | misc_init_r. + +---------------------------------------------------------------------------*/ +int misc_init_r(void) +{ + uint pbcr; + int size_val = 0; + unsigned long usb2d0cr = 0; + unsigned long usb2phy0cr, usb2h0cr = 0; + unsigned long sdr0_pfc1; + char *act = getenv("usbact"); + + /* + * FLASH stuff... + */ + + /* Re-do sizing to get full correct info */ +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) + mtdcr(ebccfga, pb3cr); +#else + mtdcr(ebccfga, pb0cr); +#endif + pbcr = mfdcr(ebccfgd); + switch (gd->bd->bi_flashsize) { + case 1 << 20: + size_val = 0; + break; + case 2 << 20: + size_val = 1; + break; + case 4 << 20: + size_val = 2; + break; + case 8 << 20: + size_val = 3; + break; + case 16 << 20: + size_val = 4; + break; + case 32 << 20: + size_val = 5; + break; + case 64 << 20: + size_val = 6; + break; + case 128 << 20: + size_val = 7; + break; + } + pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17); +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) + mtdcr(ebccfga, pb3cr); +#else + mtdcr(ebccfga, pb0cr); +#endif + mtdcr(ebccfgd, pbcr); + + /* adjust flash start and offset */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + +#ifdef CFG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + -CFG_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); + + /* Env protection ON by default */ + (void)flash_protect(FLAG_PROTECT_SET, + CFG_ENV_ADDR_REDUND, + CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1, + &flash_info[0]); +#endif + + /* + * USB suff... + */ + if (act == NULL || strcmp(act, "hostdev") == 0) { + /* SDR Setting */ + mfsdr(SDR0_PFC1, sdr0_pfc1); + mfsdr(SDR0_USB0, usb2d0cr); + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mfsdr(SDR0_USB2H0CR, usb2h0cr); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ + + /* An 8-bit/60MHz interface is the only possible alternative + when connecting the Device to the PHY */ + usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ; /*1*/ + + /* To enable the USB 2.0 Device function through the UTMI interface */ + usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; + usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION; /*1*/ + + sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; + sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL; /*0*/ + + mtsdr(SDR0_PFC1, sdr0_pfc1); + mtsdr(SDR0_USB0, usb2d0cr); + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mtsdr(SDR0_USB2H0CR, usb2h0cr); + + /*clear resets*/ + udelay (1000); + mtsdr(SDR0_SRST1, 0x00000000); + udelay (1000); + mtsdr(SDR0_SRST0, 0x00000000); + + printf("USB: Host(int phy) Device(ext phy)\n"); + + } else if (strcmp(act, "dev") == 0) { + /*-------------------PATCH-------------------------------*/ + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST; /*1*/ + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + + udelay (1000); + mtsdr(SDR0_SRST1, 0x672c6000); + + udelay (1000); + mtsdr(SDR0_SRST0, 0x00000080); + + udelay (1000); + mtsdr(SDR0_SRST1, 0x60206000); + + *(unsigned int *)(0xe0000350) = 0x00000001; + + udelay (1000); + mtsdr(SDR0_SRST1, 0x60306000); + /*-------------------PATCH-------------------------------*/ + + /* SDR Setting */ + mfsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mfsdr(SDR0_USB2H0CR, usb2h0cr); + mfsdr(SDR0_USB0, usb2d0cr); + mfsdr(SDR0_PFC1, sdr0_pfc1); + + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_XOCLK_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_WDINT_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DVBUS_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN; /*1*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_DWNSTR_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV; /*0*/ + usb2phy0cr = usb2phy0cr &~SDR0_USB2PHY0CR_UTMICN_MASK; + usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV; /*0*/ + + usb2h0cr = usb2h0cr &~SDR0_USB2H0CR_WDINT_MASK; + usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ; /*0*/ + + usb2d0cr = usb2d0cr &~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK; + usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION; /*0*/ + + sdr0_pfc1 = sdr0_pfc1 &~SDR0_PFC1_UES_MASK; + sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL; /*1*/ + + mtsdr(SDR0_USB2H0CR, usb2h0cr); + mtsdr(SDR0_USB2PHY0CR, usb2phy0cr); + mtsdr(SDR0_USB0, usb2d0cr); + mtsdr(SDR0_PFC1, sdr0_pfc1); + + /*clear resets*/ + udelay (1000); + mtsdr(SDR0_SRST1, 0x00000000); + udelay (1000); + mtsdr(SDR0_SRST0, 0x00000000); + + printf("USB: Device(int phy)\n"); + } + + return 0; +} + +int checkboard(void) +{ + char *s = getenv("serial#"); + + printf("Board: Sequoia - AMCC PPC440EPx Evaluation Board"); + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return (0); +} + +#if defined(CFG_DRAM_TEST) +int testdram(void) +{ + unsigned long *mem = (unsigned long *)0; + const unsigned long kend = (1024 / sizeof(unsigned long)); + unsigned long k, n; + + mtmsr(0); + + for (k = 0; k < CFG_MBYTES_SDRAM; + ++k, mem += (1024 / sizeof(unsigned long))) { + if ((k & 1023) == 0) { + printf("%3d MB\r", k / 1024); + } + + memset(mem, 0xaaaaaaaa, 1024); + for (n = 0; n < kend; ++n) { + if (mem[n] != 0xaaaaaaaa) { + printf("SDRAM test fails at: %08x\n", + (uint) & mem[n]); + return 1; + } + } + + memset(mem, 0x55555555, 1024); + for (n = 0; n < kend; ++n) { + if (mem[n] != 0x55555555) { + printf("SDRAM test fails at: %08x\n", + (uint) & mem[n]); + return 1; + } + } + } + printf("SDRAM test passes\n"); + return 0; +} +#endif + +/************************************************************************* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) +int pci_pre_init(struct pci_controller *hose) +{ + unsigned long addr; +#if 0 + /*--------------------------------------------------------------------------+ + * Cactus is always configured as the host & requires the + * PCI arbiter to be enabled ??? + *--------------------------------------------------------------------------*/ + unsigned long strap; + mfsdr(sdr_sdstp1, strap); + if ((strap & SDR0_SDSTP1_PAE_MASK) == 0) { + printf("PCI: SDR0_STRP1[PAE] not set.\n"); + printf("PCI: Configuration aborted.\n"); + return 0; + } +#endif + + /*-------------------------------------------------------------------------+ + | Set priority for all PLB3 devices to 0. + | Set PLB3 arbiter to fair mode. + +-------------------------------------------------------------------------*/ + mfsdr(sdr_amp1, addr); + mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb3_acr); + mtdcr(plb3_acr, addr | 0x80000000); + + /*-------------------------------------------------------------------------+ + | Set priority for all PLB4 devices to 0. + +-------------------------------------------------------------------------*/ + mfsdr(sdr_amp0, addr); + mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00); + addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */ + mtdcr(plb4_acr, addr); + + /*-------------------------------------------------------------------------+ + | Set Nebula PLB4 arbiter to fair mode. + +-------------------------------------------------------------------------*/ + /* Segment0 */ + addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair; + addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled; + addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep; + addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep; + mtdcr(plb0_acr, addr); + + /* Segment1 */ + addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair; + addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled; + addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep; + addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep; + mtdcr(plb1_acr, addr); + + return 1; +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */ + +/************************************************************************* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller *hose) +{ + /*--------------------------------------------------------------------------+ + * Set up Direct MMIO registers + *--------------------------------------------------------------------------*/ + /*--------------------------------------------------------------------------+ + | PowerPC440EPX PCI Master configuration. + | Map one 1Gig range of PLB/processor addresses to PCI memory space. + | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF + | Use byte reversed out routines to handle endianess. + | Make this region non-prefetchable. + +--------------------------------------------------------------------------*/ + out32r(PCIX0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ + out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE); /* PMM0 Local Address */ + out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE); /* PMM0 PCI Low Address */ + out32r(PCIX0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */ + out32r(PCIX0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */ + + out32r(PCIX0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */ + out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2); /* PMM0 Local Address */ + out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2); /* PMM0 PCI Low Address */ + out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */ + out32r(PCIX0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */ + + out32r(PCIX0_PTM1MS, 0x00000001); /* Memory Size/Attribute */ + out32r(PCIX0_PTM1LA, 0); /* Local Addr. Reg */ + out32r(PCIX0_PTM2MS, 0); /* Memory Size/Attribute */ + out32r(PCIX0_PTM2LA, 0); /* Local Addr. Reg */ + + /*--------------------------------------------------------------------------+ + * Set up Configuration registers + *--------------------------------------------------------------------------*/ + + /* Program the board's subsystem id/vendor id */ + pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID, + CFG_PCI_SUBSYS_VENDORID); + pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID); + + /* Configure command register as bus master */ + pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER); + + /* 240nS PCI clock */ + pci_write_config_word(0, PCI_LATENCY_TIMER, 1); + + /* No error reporting */ + pci_write_config_word(0, PCI_ERREN, 0); + + pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101); + +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ + +/************************************************************************* + * pci_master_init + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) +void pci_master_init(struct pci_controller *hose) +{ + unsigned short temp_short; + + /*--------------------------------------------------------------------------+ + | Write the PowerPC440 EP PCI Configuration regs. + | Enable PowerPC440 EP to be a master on the PCI bus (PMM). + | Enable PowerPC440 EP to act as a PCI memory target (PTM). + +--------------------------------------------------------------------------*/ + pci_read_config_word(0, PCI_COMMAND, &temp_short); + pci_write_config_word(0, PCI_COMMAND, + temp_short | PCI_COMMAND_MASTER | + PCI_COMMAND_MEMORY); +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT) */ + +/************************************************************************* + * is_pci_host + * + * This routine is called to determine if a pci scan should be + * performed. With various hardware environments (especially cPCI and + * PPMC) it's insufficient to depend on the state of the arbiter enable + * bit in the strap register, or generic host/adapter assumptions. + * + * Rather than hard-code a bad assumption in the general 440 code, the + * 440 pci code requires the board to decide at runtime. + * + * Return 0 for adapter mode, non-zero for host (monarch) mode. + * + * + ************************************************************************/ +#if defined(CONFIG_PCI) +int is_pci_host(struct pci_controller *hose) +{ + /* Cactus is always configured as host. */ + return (1); +} +#endif /* defined(CONFIG_PCI) */ diff --git a/board/amcc/sequoia/sequoia.h b/board/amcc/sequoia/sequoia.h new file mode 100644 index 00000000000..1d44b164649 --- /dev/null +++ b/board/amcc/sequoia/sequoia.h @@ -0,0 +1,67 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +/*----------------------------------------------------------------------------+ + | EBC Configuration Register - EBC0_CFG + +----------------------------------------------------------------------------*/ +/* External Bus Three-State Control */ +#define EBC0_CFG_EBTC_DRIVEN 0x80000000 +/* Device-Paced Time-out Disable */ +#define EBC0_CFG_PTD_ENABLED 0x00000000 +/* Ready Timeout Count */ +#define EBC0_CFG_RTC_MASK 0x38000000 +#define EBC0_CFG_RTC_16PERCLK 0x00000000 +#define EBC0_CFG_RTC_32PERCLK 0x08000000 +#define EBC0_CFG_RTC_64PERCLK 0x10000000 +#define EBC0_CFG_RTC_128PERCLK 0x18000000 +#define EBC0_CFG_RTC_256PERCLK 0x20000000 +#define EBC0_CFG_RTC_512PERCLK 0x28000000 +#define EBC0_CFG_RTC_1024PERCLK 0x30000000 +#define EBC0_CFG_RTC_2048PERCLK 0x38000000 +/* External Master Priority Low */ +#define EBC0_CFG_EMPL_LOW 0x00000000 +#define EBC0_CFG_EMPL_MEDIUM_LOW 0x02000000 +#define EBC0_CFG_EMPL_MEDIUM_HIGH 0x04000000 +#define EBC0_CFG_EMPL_HIGH 0x06000000 +/* External Master Priority High */ +#define EBC0_CFG_EMPH_LOW 0x00000000 +#define EBC0_CFG_EMPH_MEDIUM_LOW 0x00800000 +#define EBC0_CFG_EMPH_MEDIUM_HIGH 0x01000000 +#define EBC0_CFG_EMPH_HIGH 0x01800000 +/* Chip Select Three-State Control */ +#define EBC0_CFG_CSTC_DRIVEN 0x00400000 +/* Burst Prefetch */ +#define EBC0_CFG_BPF_ONEDW 0x00000000 +#define EBC0_CFG_BPF_TWODW 0x00100000 +#define EBC0_CFG_BPF_FOURDW 0x00200000 +/* External Master Size */ +#define EBC0_CFG_EMS_8BIT 0x00000000 +/* Power Management Enable */ +#define EBC0_CFG_PME_DISABLED 0x00000000 +#define EBC0_CFG_PME_ENABLED 0x00020000 +/* Power Management Timer */ +#define EBC0_CFG_PMT_ENCODE(n) ((((unsigned long)(n))&0x1F)<<12) + +#define SDR0_USB0 0x0320 /* USB Control Register */ diff --git a/board/amcc/sequoia/u-boot-nand.lds b/board/amcc/sequoia/u-boot-nand.lds new file mode 100644 index 00000000000..c3d3d968fed --- /dev/null +++ b/board/amcc/sequoia/u-boot-nand.lds @@ -0,0 +1,131 @@ +/* + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + _end = . ; + PROVIDE (end = .); +} diff --git a/board/amcc/sequoia/u-boot.lds b/board/amcc/sequoia/u-boot.lds new file mode 100644 index 00000000000..a423f982858 --- /dev/null +++ b/board/amcc/sequoia/u-boot.lds @@ -0,0 +1,145 @@ +/* + * (C) Copyright 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/ppc4xx/start.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); + + _end = . ; + PROVIDE (end = .); +} diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c index 256e4bc7968..70de795deed 100644 --- a/common/cmd_bdinfo.c +++ b/common/cmd_bdinfo.c @@ -62,11 +62,13 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ - defined(CONFIG_440SP) + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) print_str ("procfreq", strmhz(buf, bd->bi_procfreq)); print_str ("plb_busfreq", strmhz(buf, bd->bi_plb_busfreq)); #if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE) + defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) print_str ("pci_busfreq", strmhz(buf, bd->bi_pci_busfreq)); #endif #else /* ! CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_ML300, CONFIG_440EP CONFIG_440GR */ diff --git a/config.mk b/config.mk index 3ed7107fb80..0f5d0f43d94 100644 --- a/config.mk +++ b/config.mk @@ -132,8 +132,12 @@ DBGFLAGS= -g # -DDEBUG OPTFLAGS= -Os #-fomit-frame-pointer ifndef LDSCRIPT #LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds.debug +ifeq ($(CONFIG_NAND_U_BOOT),y) +LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds +else LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds endif +endif OBJCFLAGS += --gap-fill=0xff gccincdir := $(shell $(CC) -print-file-name=include) diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c index 0b0686bcf71..03128d3f6d1 100644 --- a/cpu/ppc4xx/405gp_pci.c +++ b/cpu/ppc4xx/405gp_pci.c @@ -555,7 +555,8 @@ void pci_440_init (struct pci_controller *hose) #ifdef CONFIG_PCI_SCAN_SHOW printf("PCI: Bus Dev VenId DevId Class Int\n"); #endif -#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) +#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER); #endif hose->last_busno = pci_hose_scan(hose); diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index fab65aff78a..5b1c17c351a 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -130,7 +130,17 @@ #define BI_PHYMODE_NONE 0 #define BI_PHYMODE_ZMII 1 #define BI_PHYMODE_RGMII 2 +#define BI_PHYMODE_GMII 3 +#define BI_PHYMODE_RTBI 4 +#define BI_PHYMODE_TBI 5 +#if defined (CONFIG_440EPX) +#define BI_PHYMODE_SMII 6 +#define BI_PHYMODE_MII 7 +#endif +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_MFR_ETH_CLK_SEL_V(n) ((0x01<<27) / (n+1)) +#endif /*-----------------------------------------------------------------------------+ * Global variables. TX and RX descriptors and buffers. @@ -181,7 +191,7 @@ static void ppc_4xx_eth_halt (struct eth_device *dev) { EMAC_4XX_HW_PST hw_p = dev->priv; uint32_t failsafe = 10000; -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) unsigned long mfr; #endif @@ -205,19 +215,19 @@ static void ppc_4xx_eth_halt (struct eth_device *dev) } /* EMAC RESET */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* provide clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); - mfr |= 0x08000000; + mfr |= SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum); mtsdr(sdr_mfr, mfr); #endif out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST); -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* remove clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); - mfr &= ~0x08000000; + mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum); mtsdr(sdr_mfr, mfr); #endif @@ -317,10 +327,50 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) out32 (RGMII_FER, rmiifer); return ((int)pfc1); - } #endif /* CONFIG_440_GX */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) +{ + unsigned long zmiifer=0x0; + + /* + * Right now only 2*RGMII is supported. Please extend when needed. + * sr - 2006-08-29 + */ + switch (1) { + case 0: + /* 1 x GMII port */ + out32 (ZMII_FER, 0x00); + out32 (RGMII_FER, 0x00000037); + bis->bi_phymode[0] = BI_PHYMODE_GMII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case 1: + /* 2 x RGMII ports */ + out32 (ZMII_FER, 0x00); + out32 (RGMII_FER, 0x00000055); + bis->bi_phymode[0] = BI_PHYMODE_RGMII; + bis->bi_phymode[1] = BI_PHYMODE_RGMII; + break; + case 2: + /* 2 x SMII ports */ + + break; + default: + break; + } + + /* Ensure we setup mdio for this devnum and ONLY this devnum */ + zmiifer = in32 (ZMII_FER); + zmiifer |= (ZMII_FER_MDI) << ZMII_FER_V(devnum); + out32 (ZMII_FER, zmiifer); + + return ((int)0x0); +} +#endif /* CONFIG_440EPX */ + static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) { int i, j; @@ -332,13 +382,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) unsigned mode_reg; unsigned short devnum; unsigned short reg_short; -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) sys_info_t sysinfo; -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) int ethgroup = -1; #endif #endif -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || defined(CONFIG_440SPE) unsigned long mfr; #endif @@ -352,7 +405,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) return -1; } -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* Need to get the OPB frequency so we can access the PHY */ get_sys_info (&sysinfo); #endif @@ -407,7 +462,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) #if defined(CONFIG_440EP) || defined(CONFIG_440GR) out32 (ZMII_FER, (ZMII_FER_RMII | ZMII_FER_MDI) << ZMII_FER_V (devnum)); -#elif defined(CONFIG_440GX) +#elif defined(CONFIG_440GX) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis); #elif defined(CONFIG_440GP) /* set RMII mode */ @@ -429,10 +484,10 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) __asm__ volatile ("eieio"); /* reset emac so we have access to the phy */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* provide clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); - mfr |= 0x08000000; + mfr |= SDR0_MFR_ETH_CLK_SEL_V(devnum); mtsdr(sdr_mfr, mfr); #endif @@ -444,15 +499,19 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) udelay (1000); failsafe--; } + if (failsafe <= 0) + printf("\nProblem resetting EMAC!\n"); -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* remove clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); - mfr &= ~0x08000000; + mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(devnum); mtsdr(sdr_mfr, mfr); #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* Whack the M1 register */ mode_reg = 0x0; mode_reg &= ~0x00000038; @@ -502,15 +561,39 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) * otherwise, just check the speeds & feeds */ if (hw_p->first_init == 0) { +#if defined(CONFIG_88E1111_CLK_DELAY) + /* + * On some boards (e.g. ALPR) the Marvell 88E1111 PHY needs + * the "RGMII transmit timing control" and "RGMII receive + * timing control" bits set, so that Gbit communication works + * without problems. + * Also set the "Transmitter disable" to 1 to enable the + * transmitter. + * After setting these bits a soft-reset must occur for this + * change to become active. + */ + miiphy_read (dev->name, reg, 0x14, ®_short); + reg_short |= (1 << 7) | (1 << 1) | (1 << 0); + miiphy_write (dev->name, reg, 0x14, reg_short); +#endif +#if defined(CONFIG_M88E1111_PHY) /* test-only: merge with CONFIG_88E1111_CLK_DELAY !!! */ + miiphy_write (dev->name, reg, 0x14, 0x0ce3); + miiphy_write (dev->name, reg, 0x18, 0x4101); + miiphy_write (dev->name, reg, 0x09, 0x0e00); + miiphy_write (dev->name, reg, 0x04, 0x01e1); +#endif miiphy_reset (dev->name, reg); -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) + #if defined(CONFIG_CIS8201_PHY) /* * Cicada 8201 PHY needs to have an extended register whacked * for RGMII mode. */ - if ( ((devnum == 2) || (devnum ==3)) && (4 == ethgroup) ) { + if (((devnum == 2) || (devnum == 3)) && (4 == ethgroup)) { #if defined(CONFIG_CIS8201_SHORT_ETCH) miiphy_write (dev->name, reg, 23, 0x1300); #else @@ -580,7 +663,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) (int) speed, (duplex == HALF) ? "HALF" : "FULL"); } -#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) +#if defined(CONFIG_440) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) #if defined(CONFIG_440EP) || defined(CONFIG_440GR) mfsdr(sdr_mfr, reg); if (speed == 100) { @@ -603,15 +687,34 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) reg = (RGMII_SSR_SP_1000MBPS << RGMII_SSR_V (devnum)); else if (speed == 100) reg = (RGMII_SSR_SP_100MBPS << RGMII_SSR_V (devnum)); - else + else if (speed == 10) reg = (RGMII_SSR_SP_10MBPS << RGMII_SSR_V (devnum)); - + else { + printf("Error in RGMII Speed\n"); + return -1; + } out32 (RGMII_SSR, reg); } #endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + if (speed == 1000) + reg = (RGMII_SSR_SP_1000MBPS << RGMII_SSR_V (devnum)); + else if (speed == 100) + reg = (RGMII_SSR_SP_100MBPS << RGMII_SSR_V (devnum)); + else if (speed == 10) + reg = (RGMII_SSR_SP_10MBPS << RGMII_SSR_V (devnum)); + else { + printf("Error in RGMII Speed\n"); + return -1; + } + out32 (RGMII_SSR, reg); +#endif + /* set the Mal configuration reg */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA | MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000); #else @@ -795,8 +898,10 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) /* set speed */ if (speed == _1000BASET) { -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) unsigned long pfc1; + mfsdr (sdr_pfc1, pfc1); pfc1 |= SDR0_PFC1_EM_1000; mtsdr (sdr_pfc1, pfc1); @@ -942,6 +1047,14 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, #define UIC0SR uic0sr #endif +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define UICMSR_ETHX uic0msr +#define UICSR_ETHX uic0sr +#else +#define UICMSR_ETHX uic1msr +#define UICSR_ETHX uic1sr +#endif + int enetInt (struct eth_device *dev) { int serviced; @@ -950,6 +1063,7 @@ int enetInt (struct eth_device *dev) unsigned long emac_isr = 0; unsigned long mal_rx_eob; unsigned long my_uic0msr, my_uic1msr; + unsigned long my_uicmsr_ethx; #if defined(CONFIG_440GX) unsigned long my_uic2msr; @@ -977,8 +1091,11 @@ int enetInt (struct eth_device *dev) #if defined(CONFIG_440GX) my_uic2msr = mfdcr (uic2msr); #endif + my_uicmsr_ethx = mfdcr (UICMSR_ETHX); + if (!(my_uic0msr & (UIC_MRE | UIC_MTE)) - && !(my_uic1msr & (UIC_ETH0 | UIC_ETH1 | UIC_MS | UIC_MTDE | UIC_MRDE))) { + && !(my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) + && !(my_uicmsr_ethx & (UIC_ETH0 | UIC_ETH1))) { /* not for us */ return (rc); } @@ -997,8 +1114,7 @@ int enetInt (struct eth_device *dev) mal_isr = mfdcr (malesr); /* look for mal error */ if (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) { - mal_err (dev, mal_isr, my_uic0msr, - MAL_UIC_DEF, MAL_UIC_ERR); + mal_err (dev, mal_isr, my_uic1msr, MAL_UIC_DEF, MAL_UIC_ERR); serviced = 1; rc = 0; } @@ -1006,7 +1122,7 @@ int enetInt (struct eth_device *dev) /* port by port dispatch of emac interrupts */ if (hw_p->devnum == 0) { - if (UIC_ETH0 & my_uic1msr) { /* look for EMAC errors */ + if (UIC_ETH0 & my_uicmsr_ethx) { /* look for EMAC errors */ emac_isr = in32 (EMAC_ISR + hw_p->hw_addr); if ((hw_p->emac_ier & emac_isr) != 0) { emac_err (dev, emac_isr); @@ -1017,14 +1133,15 @@ int enetInt (struct eth_device *dev) if ((hw_p->emac_ier & emac_isr) || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (uic1sr, UIC_ETH0 | UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ + mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ + mtdcr (UICSR_ETHX, UIC_ETH0); /* Clear */ return (rc); /* we had errors so get out */ } } #if !defined(CONFIG_440SP) if (hw_p->devnum == 1) { - if (UIC_ETH1 & my_uic1msr) { /* look for EMAC errors */ + if (UIC_ETH1 & my_uicmsr_ethx) { /* look for EMAC errors */ emac_isr = in32 (EMAC_ISR + hw_p->hw_addr); if ((hw_p->emac_ier & emac_isr) != 0) { emac_err (dev, emac_isr); @@ -1035,7 +1152,8 @@ int enetInt (struct eth_device *dev) if ((hw_p->emac_ier & emac_isr) || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (uic1sr, UIC_ETH1 | UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ + mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ + mtdcr (UICSR_ETHX, UIC_ETH1); /* Clear */ return (rc); /* we had errors so get out */ } } @@ -1102,10 +1220,10 @@ int enetInt (struct eth_device *dev) mtdcr (uic1sr, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ switch (hw_p->devnum) { case 0: - mtdcr (uic1sr, UIC_ETH0); + mtdcr (UICSR_ETHX, UIC_ETH0); break; case 1: - mtdcr (uic1sr, UIC_ETH1); + mtdcr (UICSR_ETHX, UIC_ETH1); break; #if defined (CONFIG_440GX) case 2: @@ -1512,7 +1630,7 @@ int ppc_4xx_eth_initialize (bd_t * bis) if (0 == virgin) { /* set the MAL IER ??? names may change with new spec ??? */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) mal_ier = MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE | MAL_IER_DE | MAL_IER_OTE | MAL_IER_OE | MAL_IER_PE ; diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index 93416b57bf7..16dc8d62c05 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -30,7 +30,7 @@ SOBJS = dcr.o COBJS = 405gp_pci.o 4xx_enet.o \ bedbug_405.o commproc.o \ cpu.o cpu_init.o i2c.o interrupts.o \ - miiphy.o sdram.o serial.o \ + miiphy.o ndfc.o sdram.o serial.o \ spd_sdram.o speed.o traps.o usb_ohci.o usbdev.o \ 440spe_pcie.o diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index bc51fbfdbed..94478dbb109 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -41,14 +41,15 @@ DECLARE_GLOBAL_DATA_PTR; #endif - #if defined(CONFIG_440) #define FREQ_EBC (sys_info.freqEPB) #else #define FREQ_EBC (sys_info.freqPLB / sys_info.pllExtBusDiv) #endif -#if defined(CONFIG_405GP) || defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_405GP) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define PCI_ASYNC @@ -58,7 +59,8 @@ int pci_async_enabled(void) return (mfdcr(strap) & PSR_PCI_ASYNC_EN); #endif -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) unsigned long val; mfsdr(sdr_sdstp1, val); @@ -82,9 +84,10 @@ int pci_arbiter_enabled(void) return (mfdcr(cpc0_strp1) & CPC0_STRP1_PAE_MASK); #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) unsigned long val; mfsdr(sdr_sdstp1, val); @@ -93,8 +96,10 @@ int pci_arbiter_enabled(void) } #endif -#if defined(CONFIG_405EP) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ - defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_405EP) || defined(CONFIG_440GX) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) #define I2C_BOOTROM @@ -102,17 +107,75 @@ int i2c_bootrom_enabled(void) { #if defined(CONFIG_405EP) return (mfdcr(cpc0_boot) & CPC0_BOOT_SEP); -#endif - -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) +#else unsigned long val; mfsdr(sdr_sdcs, val); return (val & SDR0_SDCS_SDD); #endif } + +#if defined(CONFIG_440GX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (16 bits)", + "EBC (8 bits)", + "EBC (32 bits)", + "EBC (8 bits)", + "PCI", + "I2C (Addr 0x54)", + "Reserved", + "I2C (Addr 0x50)", +}; +#endif + +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#define SDR0_PINSTP_SHIFT 30 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "PCI", + "I2C (Addr 0x54)", + "I2C (Addr 0x50)", +}; +#endif + +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "PCI", + "NAND (8 bits)", + "EBC (16 bits)", + "EBC (16 bits)", + "I2C (Addr 0x54)", + "PCI", + "I2C (Addr 0x52)", +}; +#endif + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "EBC (16 bits)", + "EBC (16 bits)", + "NAND (8 bits)", + "PCI", + "I2C (Addr 0x54)", + "PCI", + "I2C (Addr 0x52)", +}; +#endif + +#if defined(SDR0_PINSTP_SHIFT) +static int bootstrap_option(void) +{ + unsigned long val; + + mfsdr(sdr_pinstp, val); + return ((val & 0xe0000000) >> SDR0_PINSTP_SHIFT); +} +#endif /* SDR0_PINSTP_SHIFT */ #endif @@ -244,6 +307,22 @@ int checkcpu (void) #endif /* CONFIG_440GR */ #endif /* CONFIG_440 */ + case PVR_440EPX1_RA: + puts("EPx Rev. A - Security/Kasumi support"); + break; + + case PVR_440EPX2_RA: + puts("EPx Rev. A - No Security/Kasumi support"); + break; + + case PVR_440GRX1_RA: + puts("GRx Rev. A - Security/Kasumi support"); + break; + + case PVR_440GRX2_RA: + puts("GRx Rev. A - No Security/Kasumi support"); + break; + case PVR_440SP_RA: puts("SP Rev. A"); break; @@ -272,6 +351,10 @@ int checkcpu (void) #if defined(I2C_BOOTROM) printf (" I2C boot EEPROM %sabled\n", i2c_bootrom_enabled() ? "en" : "dis"); +#if defined(SDR0_PINSTP_SHIFT) + printf (" Bootstrap Option %c - ", (char)bootstrap_option() + 'A'); + printf ("Boot ROM Location %s\n", bootstrap_str[bootstrap_option()]); +#endif #endif #if defined(CONFIG_PCI) diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c index 886f4051562..c5a9f02566a 100644 --- a/cpu/ppc4xx/interrupts.c +++ b/cpu/ppc4xx/interrupts.c @@ -57,12 +57,13 @@ static struct irq_action irq_vecs1[32]; /* For UIC1 */ void uic1_interrupt( void * parms); /* UIC1 handler */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) static struct irq_action irq_vecs2[32]; /* For UIC2 */ void uic2_interrupt( void * parms); /* UIC2 handler */ #endif /* CONFIG_440GX CONFIG_440SPE */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) static struct irq_action irq_vecs3[32]; /* For UIC3 */ void uic3_interrupt( void * parms); /* UIC3 handler */ #endif /* CONFIG_440SPE */ @@ -119,12 +120,13 @@ int interrupt_init_cpu (unsigned *decrementer_count) irq_vecs1[vec].handler = NULL; irq_vecs1[vec].arg = NULL; irq_vecs1[vec].count = 0; -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) irq_vecs2[vec].handler = NULL; irq_vecs2[vec].arg = NULL; irq_vecs2[vec].count = 0; #endif /* CONFIG_440GX */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) irq_vecs3[vec].handler = NULL; irq_vecs3[vec].arg = NULL; irq_vecs3[vec].count = 0; @@ -230,6 +232,32 @@ void external_interrupt(struct pt_regs *regs) } /* external_interrupt CONFIG_440GX */ +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +void external_interrupt(struct pt_regs *regs) +{ + ulong uic_msr; + + /* + * Read masked interrupt status register to determine interrupt source + */ + /* 440 SPe uses base uic register */ + uic_msr = mfdcr(uic0msr); + + if ( (UICB0_UIC1CI & uic_msr) || (UICB0_UIC1NCI & uic_msr) ) + uic1_interrupt(0); + + if ( (UICB0_UIC2CI & uic_msr) || (UICB0_UIC2NCI & uic_msr) ) + uic2_interrupt(0); + + if (uic_msr & ~(UICB0_ALL)) + uic0_interrupt(0); + + mtdcr(uic0sr, uic_msr); + + return; + +} /* external_interrupt CONFIG_440EPX & CONFIG_440GRX */ + #elif defined(CONFIG_440SPE) void external_interrupt(struct pt_regs *regs) { @@ -303,7 +331,8 @@ void external_interrupt(struct pt_regs *regs) } #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* Handler for UIC0 interrupt */ void uic0_interrupt( void * parms) { @@ -394,7 +423,8 @@ void uic1_interrupt( void * parms) } #endif /* defined(CONFIG_440) */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* Handler for UIC2 interrupt */ void uic2_interrupt( void * parms) { @@ -496,7 +526,8 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg) int i = vec; #if defined(CONFIG_440) -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) { i = vec - 32; irqa = irq_vecs1; @@ -523,7 +554,8 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg) irqa[i].arg = arg; #if defined(CONFIG_440) -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) mtdcr (uic1er, mfdcr (uic1er) | (0x80000000 >> i)); else if (vec > 63) @@ -546,7 +578,8 @@ void irq_free_handler (int vec) int i = vec; #if defined(CONFIG_440) -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) { irqa = irq_vecs1; i = vec - 32; @@ -567,7 +600,8 @@ void irq_free_handler (int vec) #endif #if defined(CONFIG_440) -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) mtdcr (uic1er, mfdcr (uic1er) & ~(0x80000000 >> i)); else if (vec > 63) @@ -635,7 +669,8 @@ do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) printf("\n"); #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) printf ("\nUIC 2\n"); printf ("Nr Routine Arg Count\n"); diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c index aa580ed48f9..6b98025308f 100644 --- a/cpu/ppc4xx/miiphy.c +++ b/cpu/ppc4xx/miiphy.c @@ -173,7 +173,8 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, } sta_reg = reg; /* reg address */ /* set clock (50Mhz) and read flags */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_READ; #else @@ -183,7 +184,9 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, sta_reg = (sta_reg | EMAC_STACR_READ) & ~EMAC_STACR_CLK_100MHZ; #endif -#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE) +#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && \ + !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; #endif sta_reg = sta_reg | (addr << 5); /* Phy address */ @@ -244,7 +247,8 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr, sta_reg = 0; sta_reg = reg; /* reg address */ /* set clock (50Mhz) and read flags */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_WRITE; #else @@ -254,7 +258,9 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr, sta_reg = (sta_reg | EMAC_STACR_WRITE) & ~EMAC_STACR_CLK_100MHZ; #endif -#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && !defined(CONFIG__440SP) && !defined(CONFIG__440SPE) +#if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && \ + !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; /* Set clock frequency (PLB freq. dependend) */ #endif sta_reg = sta_reg | ((unsigned long) addr << 5);/* Phy address */ diff --git a/cpu/ppc4xx/ndfc.c b/cpu/ppc4xx/ndfc.c new file mode 100644 index 00000000000..e4ab326bbfc --- /dev/null +++ b/cpu/ppc4xx/ndfc.c @@ -0,0 +1,173 @@ +/* + * Overview: + * Platform independend driver for NDFC (NanD Flash Controller) + * integrated into EP440 cores + * + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Based on original work by + * Thomas Gleixner + * Copyright 2006 IBM + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) + +#include +#include +#include +#include + +static u8 hwctl = 0; + +static void ndfc_hwcontrol(struct mtd_info *mtdinfo, int cmd) +{ + switch (cmd) { + case NAND_CTL_SETCLE: + hwctl |= 0x1; + break; + + case NAND_CTL_CLRCLE: + hwctl &= ~0x1; + break; + + case NAND_CTL_SETALE: + hwctl |= 0x2; + break; + + case NAND_CTL_CLRALE: + hwctl &= ~0x2; + break; + } +} + +static void ndfc_write_byte(struct mtd_info *mtdinfo, u_char byte) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + + if (hwctl & 0x1) + out8(base + NDFC_CMD, byte); + else if (hwctl & 0x2) + out8(base + NDFC_ALE, byte); + else + out8(base + NDFC_DATA, byte); +} + +static u_char ndfc_read_byte(struct mtd_info *mtdinfo) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + + return (in8(base + NDFC_DATA)); +} + +static int ndfc_dev_ready(struct mtd_info *mtdinfo) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + + while (!(in32(base + NDFC_STAT) & NDFC_STAT_IS_READY)) + ; + + return 1; +} + +#ifndef CONFIG_NAND_SPL +/* + * Don't use these speedup functions in NAND boot image, since the image + * has to fit into 4kByte. + */ + +/* + * Speedups for buffer read/write/verify + * + * NDFC allows 32bit read/write of data. So we can speed up the buffer + * functions. No further checking, as nand_base will always read/write + * page aligned. + */ +static void ndfc_read_buf(struct mtd_info *mtdinfo, uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + uint32_t *p = (uint32_t *) buf; + + for(;len > 0; len -= 4) + *p++ = in32(base + NDFC_DATA); +} + +static void ndfc_write_buf(struct mtd_info *mtdinfo, const uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + uint32_t *p = (uint32_t *) buf; + + for(; len > 0; len -= 4) + out32(base + NDFC_DATA, *p++); +} + +static int ndfc_verify_buf(struct mtd_info *mtdinfo, const uint8_t *buf, int len) +{ + struct nand_chip *this = mtdinfo->priv; + ulong base = (ulong) this->IO_ADDR_W; + uint32_t *p = (uint32_t *) buf; + + for(; len > 0; len -= 4) + if (*p++ != in32(base + NDFC_DATA)) + return -1; + + return 0; +} +#endif /* #ifndef CONFIG_NAND_SPL */ + +void board_nand_init(struct nand_chip *nand) +{ + nand->eccmode = NAND_ECC_SOFT; + + nand->hwcontrol = ndfc_hwcontrol; + nand->read_byte = ndfc_read_byte; + nand->write_byte = ndfc_write_byte; + nand->dev_ready = ndfc_dev_ready; + +#ifndef CONFIG_NAND_SPL + nand->write_buf = ndfc_write_buf; + nand->read_buf = ndfc_read_buf; + nand->verify_buf = ndfc_verify_buf; +#else + /* + * Setup EBC (CS0 only right now) + */ + mtdcr(ebccfga, xbcfg); + mtdcr(ebccfgd, 0xb8400000); + + mtebc(pb0cr, CFG_EBC_PB0CR); + mtebc(pb0ap, CFG_EBC_PB0AP); +#endif + + /* Set NandFlash Core Configuration Register */ + /* Chip select 3, 1col x 2 rows */ + out32(CFG_NAND_BASE + NDFC_CCR, 0x00000000 | (CFG_NAND_CS << 24)); + out32(CFG_NAND_BASE + NDFC_BCFG0 + (CFG_NAND_CS << 2), 0x80002222); +} + +#endif diff --git a/cpu/ppc4xx/serial.c b/cpu/ppc4xx/serial.c index ad3ca6e819e..fab0d950063 100644 --- a/cpu/ppc4xx/serial.c +++ b/cpu/ppc4xx/serial.c @@ -264,10 +264,12 @@ int serial_tstc () #endif /* CONFIG_IOP480 */ /*****************************************************************************/ -#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) || defined(CONFIG_405EP) +#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_405EP) || \ + defined(CONFIG_440) #if defined(CONFIG_440) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define UART0_BASE CFG_PERIPHERAL_BASE + 0x00000300 #define UART1_BASE CFG_PERIPHERAL_BASE + 0x00000400 #else @@ -279,15 +281,34 @@ int serial_tstc () #define UART2_BASE CFG_PERIPHERAL_BASE + 0x00000600 #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) -#define CR0_MASK 0xdfffffff -#define CR0_EXTCLK_ENA 0x00800000 -#define CR0_UDIV_POS 0 -#else +#if defined(CONFIG_440GP) #define CR0_MASK 0x3fff0000 #define CR0_EXTCLK_ENA 0x00600000 #define CR0_UDIV_POS 16 -#endif /* CONFIG_440GX */ +#define UDIV_SUBTRACT 1 +#define UART0_SDR cntrl0 +#define MFREG(a, d) d = mfdcr(a) +#define MTREG(a, d) mtdcr(a, d) +#else /* #if defined(CONFIG_440GP) */ +/* all other 440 PPC's access clock divider via sdr register */ +#define CR0_MASK 0xdfffffff +#define CR0_EXTCLK_ENA 0x00800000 +#define CR0_UDIV_POS 0 +#define UDIV_SUBTRACT 0 +#define UART0_SDR sdr_uart0 +#define UART1_SDR sdr_uart1 +#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \ + defined(CONFIG_440GR) || defined(CONFIG_440GRx) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPe) +#define UART2_SDR sdr_uart2 +#endif +#if defined(CONFIG_440EP) || defined(CONFIG_440EPx) || \ + defined(CONFIG_440GR) || defined(CONFIG_440GRx) +#define UART3_SDR sdr_uart3 +#endif +#define MFREG(a, d) mfsdr(a, d) +#define MTREG(a, d) mtsdr(a, d) +#endif /* #if defined(CONFIG_440GP) */ #elif defined(CONFIG_405EP) #define UART0_BASE 0xef600300 #define UART1_BASE 0xef600400 @@ -309,21 +330,15 @@ int serial_tstc () #if defined(CONFIG_UART1_CONSOLE) #define ACTING_UART0_BASE UART1_BASE #define ACTING_UART1_BASE UART0_BASE -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) -#define UART0_SDR sdr_uart1 -#define UART1_SDR sdr_uart0 -#endif /* CONFIG_440GX */ #else #define ACTING_UART0_BASE UART0_BASE #define ACTING_UART1_BASE UART1_BASE -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) -#define UART0_SDR sdr_uart0 -#define UART1_SDR sdr_uart1 -#endif /* CONFIG_440GX */ +#endif + +#if defined(CONFIG_SERIAL_MULTI) +#define UART_BASE dev_base +#else +#define UART_BASE ACTING_UART0_BASE #endif #if defined(CONFIG_405EP) && defined(CFG_EXT_SERIAL_CLOCK) @@ -419,7 +434,7 @@ static void serial_divs (int baudrate, unsigned long *pudiv, *pbdiv = div/udiv; } -#endif /* defined(CONFIG_440) && !defined(CFG_EXT_SERIAL_CLK */ +#endif /* defined(CONFIG_440) && !defined(CFG_EXT_SERIAL_CLK) */ /* * Minimal serial functions needed to use one of the SMC ports @@ -441,23 +456,9 @@ int serial_init(void) unsigned long tmp; #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) -#if defined(CONFIG_SERIAL_MULTI) - if (UART0_BASE == dev_base) { - mfsdr(UART0_SDR,reg); - reg &= ~CR0_MASK; - } else { - mfsdr(UART1_SDR,reg); - reg &= ~CR0_MASK; - } -#else - mfsdr(UART0_SDR,reg); + MFREG(UART0_SDR, reg); reg &= ~CR0_MASK; -#endif -#else - reg = mfdcr(cntrl0) & ~CR0_MASK; -#endif /* CONFIG_440GX */ + #ifdef CFG_EXT_SERIAL_CLOCK reg |= CR0_EXTCLK_ENA; udiv = 1; @@ -471,47 +472,34 @@ int serial_init(void) serial_divs (gd->baudrate, &udiv, &bdiv); #endif -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) - reg |= udiv << CR0_UDIV_POS; /* set the UART divisor */ -#if defined(CONFIG_SERIAL_MULTI) - if (UART0_BASE == dev_base) { - mtsdr (UART0_SDR,reg); - } else { - mtsdr (UART1_SDR,reg); - } -#else - mtsdr (UART0_SDR,reg); + reg |= (udiv - UDIV_SUBTRACT) << CR0_UDIV_POS; /* set the UART divisor */ + + /* + * Configure input clock to baudrate generator for all + * available serial ports here + */ + MTREG(UART0_SDR, reg); +#if defined(UART1_SDR) + MTREG(UART1_SDR, reg); #endif -#else - reg |= (udiv - 1) << CR0_UDIV_POS; /* set the UART divisor */ - mtdcr (cntrl0, reg); +#if defined(UART2_SDR) + MTREG(UART2_SDR, reg); #endif - -#if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */ - out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ - out8 (dev_base + UART_FCR, 0x00); /* disable FIFO */ - out8 (dev_base + UART_MCR, 0x00); /* no modem control DTR RTS */ - val = in8 (dev_base + UART_LSR); /* clear line status */ - val = in8 (dev_base + UART_RBR); /* read receive buffer */ - out8 (dev_base + UART_SCR, 0x00); /* set scratchpad */ - out8 (dev_base + UART_IER, 0x00); /* set interrupt enable reg */ -#else - out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */ - out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ - out8 (ACTING_UART0_BASE + UART_FCR, 0x00); /* disable FIFO */ - out8 (ACTING_UART0_BASE + UART_MCR, 0x00); /* no modem control DTR RTS */ - val = in8 (ACTING_UART0_BASE + UART_LSR); /* clear line status */ - val = in8 (ACTING_UART0_BASE + UART_RBR); /* read receive buffer */ - out8 (ACTING_UART0_BASE + UART_SCR, 0x00); /* set scratchpad */ - out8 (ACTING_UART0_BASE + UART_IER, 0x00); /* set interrupt enable reg */ +#if defined(UART3_SDR) + MTREG(UART3_SDR, reg); #endif + + out8(UART_BASE + UART_LCR, 0x80); /* set DLAB bit */ + out8(UART_BASE + UART_DLL, bdiv); /* set baudrate divisor */ + out8(UART_BASE + UART_DLM, bdiv >> 8); /* set baudrate divisor */ + out8(UART_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ + out8(UART_BASE + UART_FCR, 0x00); /* disable FIFO */ + out8(UART_BASE + UART_MCR, 0x00); /* no modem control DTR RTS */ + val = in8(UART_BASE + UART_LSR); /* clear line status */ + val = in8(UART_BASE + UART_RBR); /* read receive buffer */ + out8(UART_BASE + UART_SCR, 0x00); /* set scratchpad */ + out8(UART_BASE + UART_IER, 0x00); /* set interrupt enable reg */ + return (0); } @@ -564,29 +552,17 @@ int serial_init (void) tmp = gd->baudrate * udiv * 16; bdiv = (clk + tmp / 2) / tmp; -#if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */ - out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ - out8 (dev_base + UART_FCR, 0x00); /* disable FIFO */ - out8 (dev_base + UART_MCR, 0x00); /* no modem control DTR RTS */ - val = in8 (dev_base + UART_LSR); /* clear line status */ - val = in8 (dev_base + UART_RBR); /* read receive buffer */ - out8 (dev_base + UART_SCR, 0x00); /* set scratchpad */ - out8 (dev_base + UART_IER, 0x00); /* set interrupt enable reg */ -#else - out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */ - out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ - out8 (ACTING_UART0_BASE + UART_FCR, 0x00); /* disable FIFO */ - out8 (ACTING_UART0_BASE + UART_MCR, 0x00); /* no modem control DTR RTS */ - val = in8 (ACTING_UART0_BASE + UART_LSR); /* clear line status */ - val = in8 (ACTING_UART0_BASE + UART_RBR); /* read receive buffer */ - out8 (ACTING_UART0_BASE + UART_SCR, 0x00); /* set scratchpad */ - out8 (ACTING_UART0_BASE + UART_IER, 0x00); /* set interrupt enable reg */ -#endif + out8(UART_BASE + UART_LCR, 0x80); /* set DLAB bit */ + out8(UART_BASE + UART_DLL, bdiv); /* set baudrate divisor */ + out8(UART_BASE + UART_DLM, bdiv >> 8); /* set baudrate divisor */ + out8(UART_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ + out8(UART_BASE + UART_FCR, 0x00); /* disable FIFO */ + out8(UART_BASE + UART_MCR, 0x00); /* no modem control DTR RTS */ + val = in8(UART_BASE + UART_LSR); /* clear line status */ + val = in8(UART_BASE + UART_RBR); /* read receive buffer */ + out8(UART_BASE + UART_SCR, 0x00); /* set scratchpad */ + out8(UART_BASE + UART_IER, 0x00); /* set interrupt enable reg */ + return (0); } @@ -598,55 +574,10 @@ void serial_setbrg_dev (unsigned long dev_base) void serial_setbrg (void) #endif { - unsigned long tmp; - unsigned long clk; - unsigned long udiv; - unsigned short bdiv; - -#ifdef CFG_EXT_SERIAL_CLOCK - clk = CFG_EXT_SERIAL_CLOCK; -#else - clk = gd->cpu_clk; -#endif - -#ifdef CONFIG_405EP - udiv = ((mfdcr (cpc0_ucr) & UCR0_MASK) >> UCR0_UDIV_POS); -#else - udiv = ((mfdcr (cntrl0) & 0x3e) >> 1) + 1; -#endif /* CONFIG_405EP */ - -#if !defined(CFG_EXT_SERIAL_CLOCK) && \ - ( defined(CONFIG_440GX) || defined(CONFIG_440EP) || \ - defined(CONFIG_440GR) || defined(CONFIG_440SP) || \ - defined(CONFIG_440SPE) ) - serial_divs (gd->baudrate, &udiv, &bdiv); - tmp = udiv << CR0_UDIV_POS; /* set the UART divisor */ -#if defined(CONFIG_SERIAL_MULTI) - if (UART0_BASE == dev_base) { - mtsdr (UART0_SDR, tmp); - } else { - mtsdr (UART1_SDR, tmp); - } -#else - mtsdr (UART0_SDR, tmp); -#endif - -#else - - tmp = gd->baudrate * udiv * 16; - bdiv = (clk + tmp / 2) / tmp; -#endif /* !defined(CFG_EXT_SERIAL_CLOCK) && (...) */ - #if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_LCR, 0x80); /* set DLAB bit */ - out8 (dev_base + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (dev_base + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (dev_base + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ + serial_init_dev(dev_base); #else - out8 (ACTING_UART0_BASE + UART_LCR, 0x80); /* set DLAB bit */ - out8 (ACTING_UART0_BASE + UART_DLL, bdiv); /* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_DLM, bdiv >> 8);/* set baudrate divisor */ - out8 (ACTING_UART0_BASE + UART_LCR, 0x03); /* clear DLAB; set 8 bits, no parity */ + serial_init(); #endif } @@ -667,19 +598,11 @@ void serial_putc (const char c) /* check THRE bit, wait for transmiter available */ for (i = 1; i < 3500; i++) { -#if defined(CONFIG_SERIAL_MULTI) - if ((in8 (dev_base + UART_LSR) & 0x20) == 0x20) -#else - if ((in8 (ACTING_UART0_BASE + UART_LSR) & 0x20) == 0x20) -#endif + if ((in8 (UART_BASE + UART_LSR) & 0x20) == 0x20) break; udelay (100); } -#if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_THR, c); /* put character out */ -#else - out8 (ACTING_UART0_BASE + UART_THR, c); /* put character out */ -#endif + out8 (UART_BASE + UART_THR, c); /* put character out */ } #if defined(CONFIG_SERIAL_MULTI) @@ -709,11 +632,7 @@ int serial_getc (void) #if defined(CONFIG_HW_WATCHDOG) WATCHDOG_RESET (); /* Reset HW Watchdog, if needed */ #endif /* CONFIG_HW_WATCHDOG */ -#if defined(CONFIG_SERIAL_MULTI) - status = in8 (dev_base + UART_LSR); -#else - status = in8 (ACTING_UART0_BASE + UART_LSR); -#endif + status = in8 (UART_BASE + UART_LSR); if ((status & asyncLSRDataReady1) != 0x0) { break; } @@ -721,22 +640,14 @@ int serial_getc (void) asyncLSROverrunError1 | asyncLSRParityError1 | asyncLSRBreakInterrupt1 )) != 0) { -#if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_LSR, -#else - out8 (ACTING_UART0_BASE + UART_LSR, -#endif + out8 (UART_BASE + UART_LSR, asyncLSRFramingError1 | asyncLSROverrunError1 | asyncLSRParityError1 | asyncLSRBreakInterrupt1); } } -#if defined(CONFIG_SERIAL_MULTI) - return (0x000000ff & (int) in8 (dev_base)); -#else - return (0x000000ff & (int) in8 (ACTING_UART0_BASE)); -#endif + return (0x000000ff & (int) in8 (UART_BASE)); } #if defined(CONFIG_SERIAL_MULTI) @@ -747,11 +658,7 @@ int serial_tstc (void) { unsigned char status; -#if defined(CONFIG_SERIAL_MULTI) - status = in8 (dev_base + UART_LSR); -#else - status = in8 (ACTING_UART0_BASE + UART_LSR); -#endif + status = in8 (UART_BASE + UART_LSR); if ((status & asyncLSRDataReady1) != 0x0) { return (1); } @@ -759,11 +666,7 @@ int serial_tstc (void) asyncLSROverrunError1 | asyncLSRParityError1 | asyncLSRBreakInterrupt1 )) != 0) { -#if defined(CONFIG_SERIAL_MULTI) - out8 (dev_base + UART_LSR, -#else - out8 (ACTING_UART0_BASE + UART_LSR, -#endif + out8 (UART_BASE + UART_LSR, asyncLSRFramingError1 | asyncLSROverrunError1 | asyncLSRParityError1 | diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c index e552c034733..2d16a83420a 100644 --- a/cpu/ppc4xx/speed.c +++ b/cpu/ppc4xx/speed.c @@ -199,7 +199,8 @@ ulong get_PCI_freq (void) #elif defined(CONFIG_440) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) void get_sys_info (sys_info_t *sysInfo) { unsigned long temp; diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 60ed2d54536..5a1ab386b18 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -117,12 +117,16 @@ .extern ext_bus_cntlr_init .extern sdram_init +#ifdef CONFIG_NAND_U_BOOT + .extern reconfig_tlb0 +#endif /* * Set up GOT: Global Offset Table * * Use r14 to access the GOT */ +#if !defined(CONFIG_NAND_SPL) START_GOT GOT_ENTRY(_GOT2_TABLE_) GOT_ENTRY(_FIXUP_TABLE_) @@ -136,6 +140,18 @@ GOT_ENTRY(_end) GOT_ENTRY(__bss_start) END_GOT +#endif /* CONFIG_NAND_SPL */ + +#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) + /* + * NAND U-Boot image is started from offset 0 + */ + .text + bl reconfig_tlb0 + GET_GOT + bl cpu_init_f /* run low-level CPU init code (from Flash) */ + bl board_init_f +#endif /* * 440 Startup -- on reset only the top 4k of the effective @@ -150,11 +166,21 @@ */ #if defined(CONFIG_440) +#if !defined(CONFIG_NAND_SPL) .section .bootpg,"ax" +#endif .globl _start_440 /**************************************************************************/ _start_440: + /*--------------------------------------------------------------------+ + | 440EPX BUP Change - Hardware team request + +--------------------------------------------------------------------*/ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + sync + nop + nop +#endif /*----------------------------------------------------------------+ | Core bug fix. Clear the esr +-----------------------------------------------------------------*/ @@ -171,15 +197,19 @@ _start_440: mtspr srr1,r0 mtspr csrr0,r0 mtspr csrr1,r0 -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* NOTE: 440GX adds machine check status regs */ + /* NOTE: 440GX adds machine check status regs */ +#if defined(CONFIG_440) && !defined(CONFIG_440GP) mtspr mcsrr0,r0 mtspr mcsrr1,r0 - mfspr r1, mcsr + mfspr r1,mcsr mtspr mcsr,r1 #endif /*----------------------------------------------------------------*/ /* Initialize debug */ /*----------------------------------------------------------------*/ + mfspr r1,dbcr0 + andis. r1, r1, 0x8000 /* test DBCR0[EDM] bit */ + bne skip_debug_init /* if set, don't clear debug register */ mtspr dbcr0,r0 mtspr dbcr1,r0 mtspr dbcr2,r0 @@ -193,6 +223,7 @@ _start_440: mfspr r1,dbsr mtspr dbsr,r1 /* Clear all valid bits */ +skip_debug_init: /*----------------------------------------------------------------*/ /* CCR0 init */ @@ -352,7 +383,53 @@ rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/ /*----------------------------------------------------------------*/ /* Continue from 'normal' start */ /*----------------------------------------------------------------*/ -2: bl 3f +2: + +#if defined(CONFIG_NAND_SPL) + /* + * Enable internal SRAM + */ + lis r2,0x7fff + ori r2,r2,0xffff + mfdcr r1,isram0_dpc + and r1,r1,r2 /* Disable parity check */ + mtdcr isram0_dpc,r1 + mfdcr r1,isram0_pmeg + and r1,r1,r2 /* Disable pwr mgmt */ + mtdcr isram0_pmeg,r1 + + /* + * Copy SPL from cache into internal SRAM + */ + li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1 + mtctr r4 + lis r2,CFG_NAND_BOOT_SPL_SRC@h + ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l + lis r3,CFG_NAND_BOOT_SPL_DST@h + ori r3,r3,CFG_NAND_BOOT_SPL_DST@l +spl_loop: + lwzu r4,4(r2) + stwu r4,4(r3) + bdnz spl_loop + + /* + * Jump to code in RAM + */ + bl 00f +00: mflr r10 + lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h + ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l + sub r10,r10,r3 + addi r10,r10,28 + mtlr r10 + blr + +start_ram: + sync + isync +#endif + + bl 3f b _start 3: li r0,0 @@ -366,6 +443,7 @@ rsttlb: tlbwe r0,r1,0x0000 /* Invalidate all entries (V=0)*/ * r3 - 1st arg to board_init(): IMMP pointer * r4 - 2nd arg to board_init(): boot flag */ +#ifndef CONFIG_NAND_SPL .text .long 0x27051956 /* U-Boot Magic Number */ .globl version_string @@ -379,6 +457,7 @@ version_string: * location (0x100) is where the CriticalInput Execption should be. */ . = EXC_OFF_SYS_RESET +#endif .globl _start _start: @@ -417,7 +496,8 @@ _start: /* Setup the internal SRAM */ /*----------------------------------------------------------------*/ li r0,0 -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) + +#ifdef CFG_INIT_RAM_DCACHE /* Clear Dcache to use as RAM */ addis r3,r0,CFG_INIT_RAM_ADDR@h ori r3,r3,CFG_INIT_RAM_ADDR@l @@ -433,19 +513,22 @@ _start: dcbz r0,r3 addi r3,r3,32 bdnz ..d_ag -#else -#if defined (CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#endif /* CFG_INIT_RAM_DCACHE */ + + /* 440EP & 440GR are only 440er PPC's without internal SRAM */ +#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) + /* not all PPC's have internal SRAM usable as L2-cache */ +#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) mtdcr l2_cache_cfg,r0 /* Ensure L2 Cache is off */ #endif - mtdcr isram0_sb1cr,r0 /* Disable bank 1 */ - li r2,0x7fff + lis r2,0x7fff ori r2,r2,0xffff mfdcr r1,isram0_dpc and r1,r1,r2 /* Disable parity check */ mtdcr isram0_dpc,r1 mfdcr r1,isram0_pmeg - andis. r1,r1,r2 /* Disable pwr mgmt */ + and r1,r1,r2 /* Disable pwr mgmt */ mtdcr isram0_pmeg,r1 lis r1,0x8000 /* BAS = 8000_0000 */ @@ -474,11 +557,12 @@ _start: lis r1, 0x0003 ori r1,r1, 0x0984 /* fourth 64k */ mtdcr isram0_sb3cr,r1 -#else +#elif defined(CONFIG_440GP) ori r1,r1,0x0380 /* 8k rw */ mtdcr isram0_sb0cr,r1 + mtdcr isram0_sb1cr,r0 /* Disable bank 1 */ #endif -#endif +#endif /* #if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) */ /*----------------------------------------------------------------*/ /* Setup the stack in internal SRAM */ @@ -495,10 +579,14 @@ _start: stwu r1,-8(r1) /* Save back chain and move SP */ stw r0,+12(r1) /* Save return addr (underflow vect) */ +#ifdef CONFIG_NAND_SPL + bl nand_boot /* will not return */ +#else GET_GOT bl cpu_init_f /* run low-level CPU init code (from Flash) */ bl board_init_f +#endif #endif /* CONFIG_440 */ @@ -808,6 +896,7 @@ _start: /*----------------------------------------------------------------------- */ +#ifndef CONFIG_NAND_SPL /*****************************************************************************/ .globl _start_of_vectors _start_of_vectors: @@ -1013,6 +1102,7 @@ crit_return: lwz r1,GPR1(r1) SYNC rfci +#endif /* CONFIG_NAND_SPL */ /* Cache functions. */ @@ -1254,6 +1344,7 @@ ppcSync: /*------------------------------------------------------------------------------*/ +#ifndef CONFIG_NAND_SPL /* * void relocate_code (addr_sp, gd, addr_moni) * @@ -1267,7 +1358,9 @@ ppcSync: */ .globl relocate_code relocate_code: -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SPE) /* * On some 440er platforms the cache is enabled in the first TLB (Boot-CS) * to speed up the boot process. Now this cache needs to be disabled. @@ -1482,22 +1575,22 @@ trap_init: cmplw 0, r7, r8 blt 4b -#if !defined(CONFIG_440GX) && !defined(CONFIG_440SPE) +#if !defined(CONFIG_440) addi r7,r0,0x1000 /* set ME bit (Machine Exceptions) */ oris r7,r7,0x0002 /* set CE bit (Critical Exceptions) */ mtmsr r7 /* change MSR */ #else - bl __440gx_msr_set - b __440gx_msr_continue + bl __440_msr_set + b __440_msr_continue -__440gx_msr_set: +__440_msr_set: addi r7,r0,0x1000 /* set ME bit (Machine Exceptions) */ oris r7,r7,0x0002 /* set CE bit (Critical Exceptions) */ mtspr srr1,r7 mflr r7 mtspr srr0,r7 rfi -__440gx_msr_continue: +__440_msr_continue: #endif mtlr r4 /* restore link register */ @@ -1516,6 +1609,7 @@ trap_reloc: stw r0, 4(r7) blr +#endif /* CONFIG_NAND_SPL */ /**************************************************************************/ diff --git a/cpu/ppc4xx/usb_ohci.c b/cpu/ppc4xx/usb_ohci.c index bb5765891f8..ab852c525cf 100644 --- a/cpu/ppc4xx/usb_ohci.c +++ b/cpu/ppc4xx/usb_ohci.c @@ -76,7 +76,7 @@ #define m16_swap(x) swap_16(x) #define m32_swap(x) swap_32(x) -#ifdef CONFIG_440EP +#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) #define ohci_cpu_to_le16(x) (x) #define ohci_cpu_to_le32(x) (x) #else @@ -1599,7 +1599,11 @@ int usb_lowlevel_init(void) gohci.disabled = 1; gohci.sleeping = 0; gohci.irq = -1; - gohci.regs = (struct ohci_regs *)(CFG_PERIPHERAL_BASE | 0x1000); +#if defined(CONFIG_440EP) + gohci.regs = (struct ohci_regs *)(CFG_PERIPHERAL_BASE | 0x1000); +#elif defined(CONFIG_440EPX) + gohci.regs = (struct ohci_regs *)(CFG_USB_HOST); +#endif gohci.flags = 0; gohci.slot_name = "ppc440"; diff --git a/cpu/ppc4xx/usbdev.c b/cpu/ppc4xx/usbdev.c index 8262c54bef1..6140d2a9089 100644 --- a/cpu/ppc4xx/usbdev.c +++ b/cpu/ppc4xx/usbdev.c @@ -3,7 +3,7 @@ #include #include -#ifdef CONFIG_440EP +#if (defined(CONFIG_440EP) || defined(CONFIG_440EPX)) && (CONFIG_COMMANDS & CFG_CMD_USB) #include #include "usbdev.h" @@ -186,6 +186,21 @@ int usbInt(void) return 0; } +#if defined(CONFIG_440EPX) +void usb_dev_init() +{ + printf("USB 2.0 Device init\n"); + + /*usb dev init */ + *(unsigned char *)USB2D0_POWER_8 = 0xa1; /* 2.0 */ + + /*enable interrupts */ + *(unsigned char *)USB2D0_INTRUSBE_8 = 0x0f; + + irq_install_handler(VECNUM_HSB2D, (interrupt_handler_t *) usbInt, + NULL); +} +#else void usb_dev_init() { #ifdef USB_2_0_DEVICE @@ -210,5 +225,6 @@ void usb_dev_init() irq_install_handler(VECNUM_USBDEV, (interrupt_handler_t *) usbInt, NULL); } +#endif -#endif /*CONFIG_440EP */ +#endif /* CONFIG_440EP || CONFIG_440EPX */ diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h index 93cef026a3f..70e436aab23 100644 --- a/cpu/ppc4xx/vecnum.h +++ b/cpu/ppc4xx/vecnum.h @@ -31,7 +31,94 @@ #ifndef _VECNUMS_H_ #define _VECNUMS_H_ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440EPX) || defined(CONFIG_440_GRX) + +/* UIC 0 */ +#define VECNUM_U0 0 /* UART 0 */ +#define VECNUM_U1 1 /* UART 1 */ +#define VECNUM_IIC0 2 /* IIC */ +#define VECNUM_KRD 3 /* Kasumi Ready for data */ +#define VECNUM_KDA 4 /* Kasumi Data Available */ +#define VECNUM_PCRW 5 /* PCI command register write */ +#define VECNUM_PPM 6 /* PCI power management */ +#define VECNUM_IIC1 7 /* IIC */ +#define VECNUM_SPI 8 /* SPI */ +#define VECNUM_EPCISER 9 /* External PCI SERR */ +#define VECNUM_MTE 10 /* MAL TXEOB */ +#define VECNUM_MRE 11 /* MAL RXEOB */ +#define VECNUM_D0 12 /* DMA channel 0 */ +#define VECNUM_D1 13 /* DMA channel 1 */ +#define VECNUM_D2 14 /* DMA channel 2 */ +#define VECNUM_D3 15 /* DMA channel 3 */ +#define VECNUM_UD0 16 /* UDMA irq 0 */ +#define VECNUM_UD1 17 /* UDMA irq 1 */ +#define VECNUM_UD2 18 /* UDMA irq 2 */ +#define VECNUM_UD3 19 /* UDMA irq 3 */ +#define VECNUM_HSB2D 20 /* USB2.0 Device */ +#define VECNUM_USBDEV 20 /* USB 1.1/USB 2.0 Device */ +#define VECNUM_OHCI1 21 /* USB2.0 Host OHCI irq 1 */ +#define VECNUM_OHCI2 22 /* USB2.0 Host OHCI irq 2 */ +#define VECNUM_EIP94 23 /* Security EIP94 */ +#define VECNUM_ETH0 24 /* Emac 0 */ +#define VECNUM_ETH1 25 /* Emac 1 */ +#define VECNUM_EHCI 26 /* USB2.0 Host EHCI */ +#define VECNUM_EIR4 27 /* External interrupt 4 */ +#define VECNUM_UIC2NC 28 /* UIC2 non-critical interrupt */ +#define VECNUM_UIC2C 29 /* UIC2 critical interrupt */ +#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ +#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ + +/* UIC 1 */ +#define VECNUM_MS (32 + 0) /* MAL SERR */ +#define VECNUM_MTDE (32 + 1) /* MAL TXDE */ +#define VECNUM_MRDE (32 + 2) /* MAL RXDE */ +#define VECNUM_U2 (32 + 3) /* UART 2 */ +#define VECNUM_U3 (32 + 4) /* UART 3 */ +#define VECNUM_EBCO (32 + 5) /* EBCO interrupt status */ +#define VECNUM_NDFC (32 + 6) /* NDFC */ +#define VECNUM_KSLE (32 + 7) /* KASUMI slave error */ +#define VECNUM_CT5 (32 + 8) /* GPT compare timer 5 */ +#define VECNUM_CT6 (32 + 9) /* GPT compare timer 6 */ +#define VECNUM_PLB34I0 (32 + 10) /* PLB3X4X MIRQ0 */ +#define VECNUM_PLB34I1 (32 + 11) /* PLB3X4X MIRQ1 */ +#define VECNUM_PLB34I2 (32 + 12) /* PLB3X4X MIRQ2 */ +#define VECNUM_PLB34I3 (32 + 13) /* PLB3X4X MIRQ3 */ +#define VECNUM_PLB34I4 (32 + 14) /* PLB3X4X MIRQ4 */ +#define VECNUM_PLB34I5 (32 + 15) /* PLB3X4X MIRQ5 */ +#define VECNUM_CT0 (32 + 16) /* GPT compare timer 0 */ +#define VECNUM_CT1 (32 + 17) /* GPT compare timer 1 */ +#define VECNUM_EIR7 (32 + 18) /* External interrupt 7 */ +#define VECNUM_EIR8 (32 + 19) /* External interrupt 8 */ +#define VECNUM_EIR9 (32 + 20) /* External interrupt 9 */ +#define VECNUM_CT2 (32 + 21) /* GPT compare timer 2 */ +#define VECNUM_CT3 (32 + 22) /* GPT compare timer 3 */ +#define VECNUM_CT4 (32 + 23) /* GPT compare timer 4 */ +#define VECNUM_SRE (32 + 24) /* Serial ROM error */ +#define VECNUM_GPTDC (32 + 25) /* GPT decrementer pulse */ +#define VECNUM_RSVD0 (32 + 26) /* Reserved */ +#define VECNUM_EPCIPER (32 + 27) /* External PCI PERR */ +#define VECNUM_EIR0 (32 + 28) /* External interrupt 0 */ +#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ +#define VECNUM_EIR1 (32 + 30) /* External interrupt 1 */ +#define VECNUM_EWU1 (32 + 31) /* Ethernet 1 wakeup */ + +#define VECNUM_TXDE VECNUM_MTDE +#define VECNUM_RXDE VECNUM_MRDE + +/* UIC 2 */ +#define VECNUM_EIR5 (62 + 0) /* External interrupt 5 */ +#define VECNUM_EIR6 (62 + 1) /* External interrupt 6 */ +#define VECNUM_OPB (62 + 2) /* OPB to PLB bridge int stat */ +#define VECNUM_EIR2 (62 + 3) /* External interrupt 2 */ +#define VECNUM_EIR3 (62 + 4) /* External interrupt 3 */ +#define VECNUM_DDR2 (62 + 5) /* DDR2 sdram */ +#define VECNUM_MCTX0 (62 + 6) /* MAl intp coalescence TX0 */ +#define VECNUM_MCTX1 (62 + 7) /* MAl intp coalescence TX1 */ +#define VECNUM_MCTR0 (62 + 8) /* MAl intp coalescence TR0 */ +#define VECNUM_MCTR1 (62 + 9) /* MAl intp coalescence TR1 */ + +#elif defined(CONFIG_440SPE) + /* UIC 0 */ #define VECNUM_U0 0 /* UART0 */ #define VECNUM_U1 1 /* UART1 */ diff --git a/doc/README.nand-boot-ppc440 b/doc/README.nand-boot-ppc440 new file mode 100644 index 00000000000..a82a10ee6a5 --- /dev/null +++ b/doc/README.nand-boot-ppc440 @@ -0,0 +1,36 @@ +----------------------------- +NAND boot on PPC440 platforms +----------------------------- + +This document describes the U-Boot NAND boot feature as it +is implemented for the AMCC Sequoia (PPC440EPx) board. + +The PPC440EP(x)/GR(x) cpu's can boot directly from NAND FLASH, +completely without NOR FLASH. This can be done by using the NAND +boot feature of the 440 NAND flash controller (NDFC). + +Here a short desciption of the different boot stages: + +a) IPL (Initial Program Loader, integrated inside CPU) +------------------------------------------------------ +Will load first 4k from NAND (SPL) into cache and execute it from there. + +b) SPL (Secondary Program Loader) +--------------------------------- +Will load special U-Boot version (NUB) from NAND and execute it. This SPL +has to fit into 4kByte. It sets up the CPU and configures the SDRAM +controller and the NAND controller so that the special U-Boot image can be +loaded from NAND to SDRAM. +This special image is build in the directory "nand_spl". + +c) NUB (NAND U-Boot) +-------------------- +This NAND U-Boot (NUB) is a special U-Boot version which can be started +from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + +On 440EPx the SPL is copied to internal SRAM before the NAND controller +is set up. While still running from cache, I experienced problems accessing +the NAND controller. + + +September 07 2006, Stefan Roese diff --git a/dtt/lm75.c b/dtt/lm75.c index 59daa453976..63f3b7551e9 100644 --- a/dtt/lm75.c +++ b/dtt/lm75.c @@ -146,8 +146,13 @@ static int _dtt_init(int sensor) /* * Setup configuraton register */ +#ifdef CONFIG_DTT_AD7414 + /* config = alert active low and disabled */ + val = 0x60; +#else /* config = 6 sample integration, int mode, active low, and enable */ val = 0x18; +#endif if (dtt_write(sensor, DTT_CONFIG, val) != 0) return 1; diff --git a/include/405_mal.h b/include/405_mal.h index 05985869534..2a421848b4b 100644 --- a/include/405_mal.h +++ b/include/405_mal.h @@ -92,7 +92,7 @@ #define MAL_ESR_PBEI 0x00000001 /* ^^ ^^ */ /* Mal IER */ -#ifdef CONFIG_440SPE +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define MAL_IER_PT 0x00000080 #define MAL_IER_PRE 0x00000040 #define MAL_IER_PWE 0x00000020 diff --git a/include/440_i2c.h b/include/440_i2c.h index 9c90a9e3c48..0c2bf362730 100644 --- a/include/440_i2c.h +++ b/include/440_i2c.h @@ -1,7 +1,8 @@ #ifndef _440_i2c_h_ #define _440_i2c_h_ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000700) #else #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000400) diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 44b23f1eb4c..bbd3497c50e 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -728,6 +728,10 @@ #define PVR_440EP_RC 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ #define PVR_440GR_RA 0x422218D3 /* 440EP rev B and 440GR rev A have same PVR */ #define PVR_440GR_RB 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ +#define PVR_440EPX1_RA 0x216218D0 /* 440EPX rev A with Security / Kasumi */ +#define PVR_440EPX2_RA 0x216218D4 /* 440EPX rev A without Security / Kasumi */ +#define PVR_440GRX1_RA 0x216218D8 /* 440GRX rev A with Security / Kasumi */ +#define PVR_440GRX2_RA 0x216218DC /* 440GRX rev A without Security / Kasumi */ #define PVR_440GX_RA 0x51B21850 #define PVR_440GX_RB 0x51B21851 #define PVR_440GX_RC 0x51B21892 diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h index f7aa55f3343..794a6d49747 100644 --- a/include/asm-ppc/u-boot.h +++ b/include/asm-ppc/u-boot.h @@ -108,7 +108,8 @@ typedef struct bd_info { #endif #if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined (CONFIG_440GX) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) unsigned int bi_opbfreq; /* OPB clock in Hz */ int bi_iic_fast[2]; /* Use fast i2c mode */ #endif diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index cd4339b5822..4961011b5cd 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -73,6 +73,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (4 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 50c1c4fd4cb..23bdfc8dfb9 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -63,6 +63,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h new file mode 100644 index 00000000000..d3fcc032aa5 --- /dev/null +++ b/include/configs/sequoia.h @@ -0,0 +1,431 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * sequoia.h - configuration for Sequoia board (PowerPC440EPx) + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_SEQUOIA 1 /* Board is Sequoia */ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ + +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfe000000 /* start of FLASH */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CFG_OCM_BASE 0xe0010000 /* ocm */ +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 + +/* Don't change either of these */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ + +#define CFG_USB2D0_BASE 0xe0000100 +#define CFG_USB_DEVICE 0xe0000000 +#define CFG_USB_HOST 0xe0000400 +#define CFG_BCSR_BASE 0xc0000000 + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +#if 0 +/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#else +#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#endif + +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +/* + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#if 1 /* test-only */ +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#endif +#if 0 +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#endif + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE CFG_NAND_ADDR + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE (512) /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT (32) /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS (5) /* Location of bad block marker */ +#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#ifdef CFG_ENV_IS_IN_NAND +#define CFG_ENV_SIZE 0x4000 +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_NAND_U_BOOT_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0xa8>>1) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x0 +#endif /* CFG_ENV_IS_IN_EEPROM */ + +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_AD7414 1 /* use AD7414 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=sequoia\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/sequoia/uImage\0" \ + "kernel_addr=FE000000\0" \ + "ramdisk_addr=FE180000\0" \ + "load=tftp 100000 /tftpboot/sequoia/u-boot.bin\0" \ + "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ + "cp.b 100000 FFFA0000 60000\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_M88E1111_PHY 1 +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 1 + +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* Comment this out to enable USB 1.1 device */ +#define USB_2_0_DEVICE + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DTT | \ + CFG_CMD_DIAG | \ + CFG_CMD_EEPROM | \ + CFG_CMD_ELF | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NAND | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM | \ + CFG_CMD_USB ) + +#define CONFIG_SUPPORT_VFAT + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT +#define CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_FLASH CFG_FLASH_BASE +#define CFG_NAND 0xD0000000 +#define CFG_CPLD 0xC0000000 + +/* + * On Sequoia CS0 and CS3 are switched when configuring for NAND booting + */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 3 /* NAND chip connected to CSx */ +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03017300 +#define CFG_EBC_PB0CR (CFG_FLASH | 0xba000) + +/* Memory Bank 3 (NAND-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x018003c0 +#define CFG_EBC_PB3CR (CFG_NAND | 0x1c000) +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 3 (NOR-FLASH) initialization */ +#define CFG_EBC_PB3AP 0x03017300 +#define CFG_EBC_PB3CR (CFG_FLASH | 0xba000) + +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND | 0x1c000) +#endif + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x24814580 +#define CFG_EBC_PB2CR (CFG_CPLD | 0x38000) + +/*----------------------------------------------------------------------- + * Cache Configuration + *----------------------------------------------------------------------*/ +#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h index cf42b666b00..bcafd8ba8b3 100644 --- a/include/configs/yellowstone.h +++ b/include/configs/yellowstone.h @@ -65,6 +65,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 86a85b8a6d3..3d7b4a2f4bc 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -65,6 +65,7 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ #define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (8 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ diff --git a/include/linux/mtd/compat.h b/include/linux/mtd/compat.h index 460cd45c808..fe55087ea93 100644 --- a/include/linux/mtd/compat.h +++ b/include/linux/mtd/compat.h @@ -31,11 +31,13 @@ #define max_t(type,x,y) \ ({ type __x = (x); type __y = (y); __x > __y ? __x: __y; }) +#ifndef BUG #define BUG() do { \ printf("U-Boot BUG at %s:%d!\n", __FILE__, __LINE__); \ } while (0) #define BUG_ON(condition) do { if (condition) BUG(); } while(0) +#endif /* BUG */ #define likely(x) __builtin_expect(!!(x), 1) #define unlikely(x) __builtin_expect(!!(x), 0) diff --git a/include/linux/mtd/ndfc.h b/include/linux/mtd/ndfc.h new file mode 100644 index 00000000000..d0558a98262 --- /dev/null +++ b/include/linux/mtd/ndfc.h @@ -0,0 +1,67 @@ +/* + * linux/include/linux/mtd/ndfc.h + * + * Copyright (c) 2006 Thomas Gleixner + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Info: + * Contains defines, datastructures for ndfc nand controller + * + */ +#ifndef __LINUX_MTD_NDFC_H +#define __LINUX_MTD_NDFC_H + +/* NDFC Register definitions */ +#define NDFC_CMD 0x00 +#define NDFC_ALE 0x04 +#define NDFC_DATA 0x08 +#define NDFC_ECC 0x10 +#define NDFC_BCFG0 0x30 +#define NDFC_BCFG1 0x34 +#define NDFC_BCFG2 0x38 +#define NDFC_BCFG3 0x3c +#define NDFC_CCR 0x40 +#define NDFC_STAT 0x44 +#define NDFC_HWCTL 0x48 +#define NDFC_REVID 0x50 + +#define NDFC_STAT_IS_READY 0x01000000 + +#define NDFC_CCR_RESET_CE 0x80000000 /* CE Reset */ +#define NDFC_CCR_RESET_ECC 0x40000000 /* ECC Reset */ +#define NDFC_CCR_RIE 0x20000000 /* Interrupt Enable on Device Rdy */ +#define NDFC_CCR_REN 0x10000000 /* Enable wait for Rdy in LinearR */ +#define NDFC_CCR_ROMEN 0x08000000 /* Enable ROM In LinearR */ +#define NDFC_CCR_ARE 0x04000000 /* Auto-Read Enable */ +#define NDFC_CCR_BS(x) (((x) & 0x3) << 24) /* Select Bank on CE[x] */ +#define NDFC_CCR_BS_MASK 0x03000000 /* Select Bank */ +#define NDFC_CCR_ARAC0 0x00000000 /* 3 Addr, 1 Col 2 Row 512b page */ +#define NDFC_CCR_ARAC1 0x00001000 /* 4 Addr, 1 Col 3 Row 512b page */ +#define NDFC_CCR_ARAC2 0x00002000 /* 4 Addr, 2 Col 2 Row 2K page */ +#define NDFC_CCR_ARAC3 0x00003000 /* 5 Addr, 2 Col 3 Row 2K page */ +#define NDFC_CCR_ARAC_MASK 0x00003000 /* Auto-Read mode Addr Cycles */ +#define NDFC_CCR_RPG 0x0000C000 /* Auto-Read Page */ +#define NDFC_CCR_EBCC 0x00000004 /* EBC Configuration Completed */ +#define NDFC_CCR_DHC 0x00000002 /* Direct Hardware Control Enable */ + +#define NDFC_BxCFG_EN 0x80000000 /* Bank Enable */ +#define NDFC_BxCFG_CED 0x40000000 /* nCE Style */ +#define NDFC_BxCFG_SZ_MASK 0x08000000 /* Bank Size */ +#define NDFC_BxCFG_SZ_8BIT 0x00000000 /* 8bit */ +#define NDFC_BxCFG_SZ_16BIT 0x08000000 /* 16bit */ + +#define NDFC_MAX_BANKS 4 + +struct ndfc_controller_settings { + uint32_t ccr_settings; + uint64_t ndfc_erpn; +}; + +struct ndfc_chip_settings { + uint32_t bank_settings; +}; + +#endif diff --git a/include/ppc440.h b/include/ppc440.h index d5a9f66a419..c4a3ed54835 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -82,7 +82,10 @@ #define ivor13 0x19d /* interrupt vector offset register 13 */ #define ivor14 0x19e /* interrupt vector offset register 14 */ #define ivor15 0x19f /* interrupt vector offset register 15 */ -#if defined(CONFIG_440GX) || defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) #define mcsrr0 0x23a /* machine check save/restore register 0 */ #define mcsrr1 0x23b /* mahcine check save/restore register 1 */ #define mcsr 0x23c /* machine check status register */ @@ -151,7 +154,18 @@ #define sdr_ecid1 0x0081 #define sdr_ecid2 0x0082 #define sdr_jtag 0x00c0 +#if !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) #define sdr_ddrdl 0x00e0 +#else +#define sdr_cfg 0x00e0 +#define SDR_CFG_LT2_MASK 0x01000000 /* Leakage test 2*/ +#define SDR_CFG_64_32BITS_MASK 0x01000000 /* Switch DDR 64 bits or 32 bits */ +#define SDR_CFG_32BITS 0x00000000 /* 32 bits */ +#define SDR_CFG_64BITS 0x01000000 /* 64 bits */ +#define SDR_CFG_MC_V2518_MASK 0x02000000 /* Low VDD2518 (2.5 or 1.8V) */ +#define SDR_CFG_MC_V25 0x00000000 /* 2.5 V */ +#define SDR_CFG_MC_V18 0x02000000 /* 1.8 V */ +#endif /* !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) */ #define sdr_ebc 0x0100 #define sdr_uart0 0x0120 /* UART0 Config */ #define sdr_uart1 0x0121 /* UART1 Config */ @@ -180,6 +194,54 @@ #define sdr_plbtr 0x4200 #define sdr_mfr 0x4300 /* SDR0_MFR reg */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* test-only!!!! */ +#define DDR0_00 0x00 +#define DDR0_01 0x01 +#define DDR0_02 0x02 +#define DDR0_03 0x03 +#define DDR0_04 0x04 +#define DDR0_05 0x05 +#define DDR0_06 0x06 +#define DDR0_07 0x07 +#define DDR0_08 0x08 +#define DDR0_09 0x09 +#define DDR0_10 0x0A +#define DDR0_11 0x0B +#define DDR0_12 0x0C +#define DDR0_13 0x0D +#define DDR0_14 0x0E +#define DDR0_15 0x0F +#define DDR0_16 0x10 +#define DDR0_17 0x11 +#define DDR0_18 0x12 +#define DDR0_19 0x13 +#define DDR0_20 0x14 +#define DDR0_21 0x15 +#define DDR0_22 0x16 +#define DDR0_23 0x17 +#define DDR0_24 0x18 +#define DDR0_25 0x19 +#define DDR0_26 0x1A +#define DDR0_27 0x1B +#define DDR0_28 0x1C +#define DDR0_29 0x1D +#define DDR0_30 0x1E +#define DDR0_31 0x1F +#define DDR0_32 0x20 +#define DDR0_33 0x21 +#define DDR0_34 0x22 +#define DDR0_35 0x23 +#define DDR0_36 0x24 +#define DDR0_37 0x25 +#define DDR0_38 0x26 +#define DDR0_39 0x27 +#define DDR0_40 0x28 +#define DDR0_41 0x29 +#define DDR0_42 0x2A +#define DDR0_43 0x2B +#define DDR0_44 0x2C +#endif /*CONFIG_440EPX*/ + /*----------------------------------------------------------------------------- | SDRAM Controller +----------------------------------------------------------------------------*/ @@ -787,7 +849,8 @@ #define xbcfg 0x23 /* external bus configuration reg */ #define xbcid 0x24 /* external bus core id reg */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* PLB4 to PLB3 Bridge OUT */ #define P4P3_DCR_BASE 0x020 @@ -877,6 +940,7 @@ #define plb1_bearl (PLB_ARBITER_BASE+ 0x0C) #define plb1_bearh (PLB_ARBITER_BASE+ 0x0D) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) /* Pin Function Control Register 1 */ #define SDR0_PFC1 0x4101 #define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ @@ -918,6 +982,178 @@ #define SDR0_USB0_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ #define SDR0_USB0_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ +/* Miscealleneaous Function Reg. */ +#define SDR0_MFR 0x4300 +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ +#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ + +#endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */ + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR_USB2D0CR 0x0320 +#define SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK 0x00000004 /* USB 2.0 Device/EBC Master Selection */ +#define SDR0_USB2D0CR_USB2DEV_SELECTION 0x00000004 /* USB 2.0 Device Selection */ +#define SDR0_USB2D0CR_EBC_SELECTION 0x00000000 /* EBC Selection */ + +#define SDR0_USB2D0CR_USB_DEV_INT_SEL_MASK 0x00000002 /* USB Device Interface Selection */ +#define SDR0_USB2D0CR_USB20D_DEVSEL 0x00000000 /* USB2.0 Device Selected */ +#define SDR0_USB2D0CR_USB11D_DEVSEL 0x00000002 /* USB1.1 Device Selected */ + +#define SDR0_USB2D0CR_LEEN_MASK 0x00000001 /* Little Endian selection */ +#define SDR0_USB2D0CR_LEEN_DISABLE 0x00000000 /* Little Endian Disable */ +#define SDR0_USB2D0CR_LEEN_ENABLE 0x00000001 /* Little Endian Enable */ + +/* USB2 Host Control Register */ +#define SDR0_USB2H0CR 0x0340 +#define SDR0_USB2H0CR_WDINT_MASK 0x00000001 /* Host UTMI Word Interface */ +#define SDR0_USB2H0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit/60MHz */ +#define SDR0_USB2H0CR_WDINT_16BIT_30MHZ 0x00000001 /* 16-bit/30MHz */ +#define SDR0_USB2H0CR_EFLADJ_MASK 0x0000007e /* EHCI Frame Length Adjustment */ + +/* Pin Function Control Register 1 */ +#define SDR0_PFC1 0x4101 +#define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ +#define SDR0_PFC1_U1ME_DSR_DTR 0x00000000 /* UART1 in DSR/DTR Mode */ +#define SDR0_PFC1_U1ME_CTS_RTS 0x02000000 /* UART1 in CTS/RTS Mode */ + +#define SDR0_PFC1_SELECT_MASK 0x01C00000 /* Ethernet Pin Select EMAC 0 */ +#define SDR0_PFC1_SELECT_CONFIG_1_1 0x00C00000 /* 1xMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_2 0x00C00000 /* 1xGMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_3 0x01000000 /* 1xTBI using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_4 0x01400000 /* 2xRGMII using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_5 0x01800000 /* 2xRTBI using RGMII bridge */ +#define SDR0_PFC1_SELECT_CONFIG_6 0x00800000 /* 2xSMII using ZMII bridge */ + +#define SDR0_PFC1_U0ME_MASK 0x00080000 /* UART0 Mode Enable */ +#define SDR0_PFC1_U0ME_DSR_DTR 0x00000000 /* UART0 in DSR/DTR Mode */ +#define SDR0_PFC1_U0ME_CTS_RTS 0x00080000 /* UART0 in CTS/RTS Mode */ +#define SDR0_PFC1_U0IM_MASK 0x00040000 /* UART0 Interface Mode */ +#define SDR0_PFC1_U0IM_8PINS 0x00000000 /* UART0 Interface Mode 8 pins */ +#define SDR0_PFC1_U0IM_4PINS 0x00040000 /* UART0 Interface Mode 4 pins */ +#define SDR0_PFC1_SIS_MASK 0x00020000 /* SCP or IIC1 Selection */ +#define SDR0_PFC1_SIS_SCP_SEL 0x00000000 /* SCP Selected */ +#define SDR0_PFC1_SIS_IIC1_SEL 0x00020000 /* IIC1 Selected */ +#define SDR0_PFC1_UES_MASK 0x00010000 /* USB2D_RX_Active / EBC_Hold Req Selection */ +#define SDR0_PFC1_UES_USB2D_SEL 0x00000000 /* USB2D_RX_Active Selected */ +#define SDR0_PFC1_UES_EBCHR_SEL 0x00010000 /* EBC_Hold Req Selected */ +#define SDR0_PFC1_DIS_MASK 0x00008000 /* DMA_Req(1) / UIC_IRQ(5) Selection */ +#define SDR0_PFC1_DIS_DMAR_SEL 0x00000000 /* DMA_Req(1) Selected */ +#define SDR0_PFC1_DIS_UICIRQ5_SEL 0x00008000 /* UIC_IRQ(5) Selected */ +#define SDR0_PFC1_ERE_MASK 0x00004000 /* EBC Mast.Ext.Req.En./GPIO0(27) Selection */ +#define SDR0_PFC1_ERE_EXTR_SEL 0x00000000 /* EBC Mast.Ext.Req.En. Selected */ +#define SDR0_PFC1_ERE_GPIO0_27_SEL 0x00004000 /* GPIO0(27) Selected */ +#define SDR0_PFC1_UPR_MASK 0x00002000 /* USB2 Device Packet Reject Selection */ +#define SDR0_PFC1_UPR_DISABLE 0x00000000 /* USB2 Device Packet Reject Disable */ +#define SDR0_PFC1_UPR_ENABLE 0x00002000 /* USB2 Device Packet Reject Enable */ + +#define SDR0_PFC1_PLB_PME_MASK 0x00001000 /* PLB3/PLB4 Perf. Monitor En. Selection */ +#define SDR0_PFC1_PLB_PME_PLB3_SEL 0x00000000 /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ +#define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ + +/* Ethernet PLL Configuration Register */ +#define SDR0_PFC2 0x4102 +#define SDR0_PFC2_TUNE_MASK 0x01FF8000 /* Loop stability tuning bits */ +#define SDR0_PFC2_MULTI_MASK 0x00007C00 /* Frequency multiplication selector */ +#define SDR0_PFC2_RANGEB_MASK 0x00000380 /* PLLOUTB/C frequency selector */ +#define SDR0_PFC2_RANGEA_MASK 0x00000071 /* PLLOUTA frequency selector */ + +#define SDR0_PFC2_SELECT_MASK 0xE0000000 /* Ethernet Pin select EMAC1 */ +#define SDR0_PFC2_SELECT_CONFIG_1_1 0x60000000 /* 1xMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_1_2 0x00000000 /* 1xMII using ZMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_2 0x60000000 /* 1xGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_3 0x80000000 /* 1xTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_4 0xA0000000 /* 2xRGMII using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_5 0xC0000000 /* 2xRTBI using RGMII bridge */ +#define SDR0_PFC2_SELECT_CONFIG_6 0x40000000 /* 2xSMII using ZMII bridge */ + +/* USB2PHY0 Control Register */ +#define SDR0_USB2PHY0CR 0x4103 +#define SDR0_USB2PHY0CR_UTMICN_MASK 0x00100000 /* PHY UTMI interface connection */ +#define SDR0_USB2PHY0CR_UTMICN_DEV 0x00000000 /* Device support */ +#define SDR0_USB2PHY0CR_UTMICN_HOST 0x00100000 /* Host support */ + +#define SDR0_USB2PHY0CR_DWNSTR_MASK 0x00400000 /* Select downstream port mode */ +#define SDR0_USB2PHY0CR_DWNSTR_DEV 0x00000000 /* Device */ +#define SDR0_USB2PHY0CR_DWNSTR_HOST 0x00400000 /* Host */ + +#define SDR0_USB2PHY0CR_DVBUS_MASK 0x00800000 /* VBus detect (Device mode only) */ +#define SDR0_USB2PHY0CR_DVBUS_PURDIS 0x00000000 /* Pull-up resistance on D+ is disabled */ +#define SDR0_USB2PHY0CR_DVBUS_PUREN 0x00800000 /* Pull-up resistance on D+ is enabled */ + +#define SDR0_USB2PHY0CR_WDINT_MASK 0x01000000 /* PHY UTMI data width and clock select */ +#define SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ 0x00000000 /* 8-bit data/60MHz */ +#define SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ 0x01000000 /* 16-bit data/30MHz */ + +#define SDR0_USB2PHY0CR_LOOPEN_MASK 0x02000000 /* Loop back test enable */ +#define SDR0_USB2PHY0CR_LOOP_ENABLE 0x00000000 /* Loop back disabled */ +#define SDR0_USB2PHY0CR_LOOP_DISABLE 0x02000000 /* Loop back enabled (only test purposes) */ + +#define SDR0_USB2PHY0CR_XOON_MASK 0x04000000 /* Force XO block on during a suspend */ +#define SDR0_USB2PHY0CR_XO_ON 0x00000000 /* PHY XO block is powered-on */ +#define SDR0_USB2PHY0CR_XO_OFF 0x04000000 /* PHY XO block is powered-off when all ports are suspended */ + +#define SDR0_USB2PHY0CR_PWRSAV_MASK 0x08000000 /* Select PHY power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_OFF 0x00000000 /* Non-power-save mode */ +#define SDR0_USB2PHY0CR_PWRSAV_ON 0x08000000 /* Power-save mode. Valid only for full-speed operation */ + +#define SDR0_USB2PHY0CR_XOREF_MASK 0x10000000 /* Select reference clock source */ +#define SDR0_USB2PHY0CR_XOREF_INTERNAL 0x00000000 /* PHY PLL uses chip internal 48M clock as a reference */ +#define SDR0_USB2PHY0CR_XOREF_XO 0x10000000 /* PHY PLL uses internal XO block output as a reference */ + +#define SDR0_USB2PHY0CR_XOCLK_MASK 0x20000000 /* Select clock for XO block */ +#define SDR0_USB2PHY0CR_XOCLK_EXTERNAL 0x00000000 /* PHY macro used an external clock */ +#define SDR0_USB2PHY0CR_XOCLK_CRYSTAL 0x20000000 /* PHY macro uses the clock from a crystal */ + +#define SDR0_USB2PHY0CR_CLKSEL_MASK 0xc0000000 /* Select ref clk freq */ +#define SDR0_USB2PHY0CR_CLKSEL_12MHZ 0x00000000 /* Select ref clk freq = 12 MHz*/ +#define SDR0_USB2PHY0CR_CLKSEL_48MHZ 0x40000000 /* Select ref clk freq = 48 MHz*/ +#define SDR0_USB2PHY0CR_CLKSEL_24MHZ 0x80000000 /* Select ref clk freq = 24 MHz*/ + +/* Miscealleneaous Function Reg. */ +#define SDR0_MFR 0x4300 +#define SDR0_MFR_ETH0_CLK_SEL_MASK 0x08000000 /* Ethernet0 Clock Select */ +#define SDR0_MFR_ETH0_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ETH1_CLK_SEL_MASK 0x04000000 /* Ethernet1 Clock Select */ +#define SDR0_MFR_ETH1_CLK_SEL_EXT 0x00000000 +#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ +#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ +#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ +#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ +#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ +#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) + +#define SDR0_MFR_ERRATA3_EN0 0x00800000 +#define SDR0_MFR_ERRATA3_EN1 0x00400000 +#define SDR0_MFR_PKT_REJ_MASK 0x00180000 /* Pkt Rej. Enable Mask */ +#define SDR0_MFR_PKT_REJ_EN 0x00180000 /* Pkt Rej. Enable on both EMAC3 0-1 */ +#define SDR0_MFR_PKT_REJ_EN0 0x00100000 /* Pkt Rej. Enable on EMAC3(0) */ +#define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ +#define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ + +#endif /* defined(CONFIG_440EPX) || defined(CONFIG_440GRX) */ + /* CUST0 Customer Configuration Register0 */ #define SDR0_CUST0 0x4000 #define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ @@ -1007,27 +1243,18 @@ #define SDR0_PFC1_PLB_PME_PLB4_SEL 0x00001000 /* PLB3 Performance Monitor Enable */ #define SDR0_PFC1_GFGGI_MASK 0x0000000F /* GPT Frequency Generation Gated In */ -/* Miscealleneaous Function Reg. */ -#define SDR0_MFR 0x4300 -#define SDR0_MFR_ETH0_CLK_SEL 0x08000000 /* Ethernet0 Clock Select */ -#define SDR0_MFR_ETH1_CLK_SEL 0x04000000 /* Ethernet1 Clock Select */ -#define SDR0_MFR_ZMII_MODE_MASK 0x03000000 /* ZMII Mode Mask */ -#define SDR0_MFR_ZMII_MODE_MII 0x00000000 /* ZMII Mode MII */ -#define SDR0_MFR_ZMII_MODE_SMII 0x01000000 /* ZMII Mode SMII */ -#define SDR0_MFR_ZMII_MODE_RMII_10M 0x02000000 /* ZMII Mode RMII - 10 Mbs */ -#define SDR0_MFR_ZMII_MODE_RMII_100M 0x03000000 /* ZMII Mode RMII - 100 Mbs */ -#define SDR0_MFR_ZMII_MODE_BIT0 0x02000000 /* ZMII Mode Bit0 */ -#define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ -#define SDR0_MFR_ZM_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) -#define SDR0_MFR_ZM_DECODE(n) ((((unsigned long)(n))<<24)&0x3) - -#define SDR0_MFR_ERRATA3_EN0 0x00800000 -#define SDR0_MFR_ERRATA3_EN1 0x00400000 -#define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ -#define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */ -#define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ -#define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ -#define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ +/*----------------------------------------------------------------------------- + | Internal SRAM + +----------------------------------------------------------------------------*/ +#define ISRAM0_DCR_BASE 0x380 +#define isram0_sb0cr (ISRAM0_DCR_BASE+0x00) /* SRAM bank config 0*/ +#define isram0_bear (ISRAM0_DCR_BASE+0x04) /* SRAM bus error addr reg */ +#define isram0_besr0 (ISRAM0_DCR_BASE+0x05) /* SRAM bus error status reg 0 */ +#define isram0_besr1 (ISRAM0_DCR_BASE+0x06) /* SRAM bus error status reg 1 */ +#define isram0_pmeg (ISRAM0_DCR_BASE+0x07) /* SRAM power management */ +#define isram0_cid (ISRAM0_DCR_BASE+0x08) /* SRAM bus core id reg */ +#define isram0_revid (ISRAM0_DCR_BASE+0x09) /* SRAM bus revision id reg */ +#define isram0_dpc (ISRAM0_DCR_BASE+0x0a) /* SRAM data parity check reg */ #else @@ -1121,7 +1348,7 @@ #define uic1vr (UIC1_DCR_BASE+0x7) /* UIC1 vector */ #define uic1vcr (UIC1_DCR_BASE+0x8) /* UIC1 vector configuration */ -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define UIC2_DCR_BASE 0xe0 #define uic2sr (UIC0_DCR_BASE+0x0) /* UIC2 status-Read Clear */ #define uic2srs (UIC0_DCR_BASE+0x1) /* UIC2 status-Read Set */ @@ -1423,6 +1650,46 @@ #define UIC_EIR6 0x00000004 /* External interrupt 6 */ #define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ #define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UIC_U0 0x80000000 /* UART 0 */ +#define UIC_U1 0x40000000 /* UART 1 */ +#define UIC_IIC0 0x20000000 /* IIC */ +#define UIC_KRD 0x10000000 /* Kasumi Ready for data */ +#define UIC_KDA 0x08000000 /* Kasumi Data Available */ +#define UIC_PCRW 0x04000000 /* PCI command register write */ +#define UIC_PPM 0x02000000 /* PCI power management */ +#define UIC_IIC1 0x01000000 /* IIC */ +#define UIC_SPI 0x00800000 /* SPI */ +#define UIC_EPCISER 0x00400000 /* External PCI SERR */ +#define UIC_MTE 0x00200000 /* MAL TXEOB */ +#define UIC_MRE 0x00100000 /* MAL RXEOB */ +#define UIC_D0 0x00080000 /* DMA channel 0 */ +#define UIC_D1 0x00040000 /* DMA channel 1 */ +#define UIC_D2 0x00020000 /* DMA channel 2 */ +#define UIC_D3 0x00010000 /* DMA channel 3 */ +#define UIC_UD0 0x00008000 /* UDMA irq 0 */ +#define UIC_UD1 0x00004000 /* UDMA irq 1 */ +#define UIC_UD2 0x00002000 /* UDMA irq 2 */ +#define UIC_UD3 0x00001000 /* UDMA irq 3 */ +#define UIC_HSB2D 0x00000800 /* USB2.0 Device */ +#define UIC_OHCI1 0x00000400 /* USB2.0 Host OHCI irq 1 */ +#define UIC_OHCI2 0x00000200 /* USB2.0 Host OHCI irq 2 */ +#define UIC_EIP94 0x00000100 /* Security EIP94 */ +#define UIC_ETH0 0x00000080 /* Emac 0 */ +#define UIC_ETH1 0x00000040 /* Emac 1 */ +#define UIC_EHCI 0x00000020 /* USB2.0 Host EHCI */ +#define UIC_EIR4 0x00000010 /* External interrupt 4 */ +#define UIC_UIC2NC 0x00000008 /* UIC2 non-critical interrupt */ +#define UIC_UIC2C 0x00000004 /* UIC2 critical interrupt */ +#define UIC_UIC1NC 0x00000002 /* UIC1 non-critical interrupt */ +#define UIC_UIC1C 0x00000001 /* UIC1 critical interrupt */ + +/* For compatibility with 405 code */ +#define UIC_MAL_TXEOB UIC_MTE +#define UIC_MAL_RXEOB UIC_MRE + #elif !defined(CONFIG_440SPE) #define UIC_U0 0x80000000 /* UART 0 */ #define UIC_U1 0x40000000 /* UART 1 */ @@ -1531,6 +1798,48 @@ #define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ #define UIC_ETH1 0x00000002 /* Ethernet 1 */ #define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UIC_MS 0x80000000 /* MAL SERR */ +#define UIC_MTDE 0x40000000 /* MAL TXDE */ +#define UIC_MRDE 0x20000000 /* MAL RXDE */ +#define UIC_U2 0x10000000 /* UART 2 */ +#define UIC_U3 0x08000000 /* UART 3 */ +#define UIC_EBCO 0x04000000 /* EBCO interrupt status */ +#define UIC_NDFC 0x02000000 /* NDFC */ +#define UIC_KSLE 0x01000000 /* KASUMI slave error */ +#define UIC_CT5 0x00800000 /* GPT compare timer 5 */ +#define UIC_CT6 0x00400000 /* GPT compare timer 6 */ +#define UIC_PLB34I0 0x00200000 /* PLB3X4X MIRQ0 */ +#define UIC_PLB34I1 0x00100000 /* PLB3X4X MIRQ1 */ +#define UIC_PLB34I2 0x00080000 /* PLB3X4X MIRQ2 */ +#define UIC_PLB34I3 0x00040000 /* PLB3X4X MIRQ3 */ +#define UIC_PLB34I4 0x00020000 /* PLB3X4X MIRQ4 */ +#define UIC_PLB34I5 0x00010000 /* PLB3X4X MIRQ5 */ +#define UIC_CT0 0x00008000 /* GPT compare timer 0 */ +#define UIC_CT1 0x00004000 /* GPT compare timer 1 */ +#define UIC_EIR7 0x00002000 /* External interrupt 7 */ +#define UIC_EIR8 0x00001000 /* External interrupt 8 */ +#define UIC_EIR9 0x00000800 /* External interrupt 9 */ +#define UIC_CT2 0x00000400 /* GPT compare timer 2 */ +#define UIC_CT3 0x00000200 /* GPT compare timer 3 */ +#define UIC_CT4 0x00000100 /* GPT compare timer 4 */ +#define UIC_SRE 0x00000080 /* Serial ROM error */ +#define UIC_GPTDC 0x00000040 /* GPT decrementer pulse */ +#define UIC_RSVD0 0x00000020 /* Reserved */ +#define UIC_EPCIPER 0x00000010 /* External PCI PERR */ +#define UIC_EIR0 0x00000008 /* External interrupt 0 */ +#define UIC_EWU0 0x00000004 /* Ethernet 0 wakeup */ +#define UIC_EIR1 0x00000002 /* External interrupt 1 */ +#define UIC_EWU1 0x00000001 /* Ethernet 1 wakeup */ + +/* For compatibility with 405 code */ +#define UIC_MAL_SERR UIC_MS +#define UIC_MAL_TXDE UIC_MTDE +#define UIC_MAL_RXDE UIC_MRDE +#define UIC_ENET UIC_ETH0 + #elif !defined(CONFIG_440SPE) #define UIC_MS 0x80000000 /* MAL SERR */ #define UIC_MTDE 0x40000000 /* MAL TXDE */ @@ -1608,6 +1917,20 @@ #define UIC_RSVD29 0x00000004 /* Reserved */ #define UIC_RSVD30 0x00000002 /* Reserved */ #define UIC_RSVD31 0x00000001 /* Reserved */ + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* UIC2 */ + +#define UIC_EIR5 0x80000000 /* External interrupt 5 */ +#define UIC_EIR6 0x40000000 /* External interrupt 6 */ +#define UIC_OPB 0x20000000 /* OPB to PLB bridge interrupt stat */ +#define UIC_EIR2 0x10000000 /* External interrupt 2 */ +#define UIC_EIR3 0x08000000 /* External interrupt 3 */ +#define UIC_DDR2 0x04000000 /* DDR2 sdram */ +#define UIC_MCTX0 0x02000000 /* MAl intp coalescence TX0 */ +#define UIC_MCTX1 0x01000000 /* MAl intp coalescence TX1 */ +#define UIC_MCTR0 0x00800000 /* MAl intp coalescence TR0 */ +#define UIC_MCTR1 0x00400000 /* MAl intp coalescence TR1 */ + #endif /* CONFIG_440GX */ /*---------------------------------------------------------------------------+ @@ -1623,6 +1946,17 @@ #define UICB0_ALL (UICB0_UIC0CI | UICB0_UIC0NCI | UICB0_UIC1CI | \ UICB0_UIC1NCI | UICB0_UIC2CI | UICB0_UIC2NCI) + +#elif defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +#define UICB0_UIC1CI 0x00000000 /* UIC1 Critical Interrupt */ +#define UICB0_UIC1NCI 0x00000000 /* UIC1 Noncritical Interrupt */ +#define UICB0_UIC2CI 0x00000000 /* UIC2 Critical Interrupt */ +#define UICB0_UIC2NCI 0x00000000 /* UIC2 Noncritical Interrupt */ + +#define UICB0_ALL (UICB0_UIC1CI | UICB0_UIC1NCI | \ + UICB0_UIC1CI | UICB0_UIC2NCI) + #endif /* CONFIG_440GX */ /*---------------------------------------------------------------------------+ | Universal interrupt controller interrupts @@ -2262,7 +2596,8 @@ #define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 13) #define SDR0_SDSTP1_PISE_MASK (0x80000000 >> 15) #endif /* defined(CONFIG_440GX) || defined(CONFIG_440SP) */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_SDSTP1_PAE_MASK (0x80000000 >> 21) #define SDR0_SDSTP1_PAME_MASK (0x80000000 >> 27) #endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */ @@ -2390,11 +2725,81 @@ #define SDR0_MFR_ZMII_MODE_BIT1 0x01000000 /* ZMII Mode Bit1 */ #define SDR0_MFR_ERRATA3_EN0 0x00800000 #define SDR0_MFR_ERRATA3_EN1 0x00400000 +#if defined(CONFIG_440GX) /* test-only: only 440GX or 440SPE??? */ #define SDR0_MFR_PKT_REJ_MASK 0x00300000 /* Pkt Rej. Enable Mask */ #define SDR0_MFR_PKT_REJ_EN 0x00300000 /* Pkt Rej. Enable on both EMAC3 0-1 */ #define SDR0_MFR_PKT_REJ_EN0 0x00200000 /* Pkt Rej. Enable on EMAC3(0) */ #define SDR0_MFR_PKT_REJ_EN1 0x00100000 /* Pkt Rej. Enable on EMAC3(1) */ #define SDR0_MFR_PKT_REJ_POL 0x00080000 /* Packet Reject Polarity */ +#endif + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_PFC1_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<22) +#define SDR0_PFC1_EPS_DECODE(n) ((((unsigned long)(n))>>22)&0x07) +#define SDR0_PFC2_EPS_ENCODE(n) ((((unsigned long)(n))&0x07)<<29) +#define SDR0_PFC2_EPS_DECODE(n) ((((unsigned long)(n))>>29)&0x07) +#endif + +#define SDR0_MFR_ECS_MASK 0x10000000 +#define SDR0_MFR_ECS_INTERNAL 0x10000000 + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define SDR0_SRST0 0x200 +#define SDR0_SRST0_BGO 0x80000000 /* PLB to OPB bridge */ +#define SDR0_SRST0_PLB4 0x40000000 /* PLB4 arbiter */ +#define SDR0_SRST0_EBC 0x20000000 /* External bus controller */ +#define SDR0_SRST0_OPB 0x10000000 /* OPB arbiter */ +#define SDR0_SRST0_UART0 0x08000000 /* Universal asynchronous receiver/transmitter 0 */ +#define SDR0_SRST0_UART1 0x04000000 /* Universal asynchronous receiver/transmitter 1 */ +#define SDR0_SRST0_IIC0 0x02000000 /* Inter integrated circuit 0 */ +#define SDR0_SRST0_USB2H 0x01000000 /* USB2.0 Host */ +#define SDR0_SRST0_GPIO 0x00800000 /* General purpose I/O */ +#define SDR0_SRST0_GPT 0x00400000 /* General purpose timer */ +#define SDR0_SRST0_DMC 0x00200000 /* DDR SDRAM memory controller */ +#define SDR0_SRST0_PCI 0x00100000 /* PCI */ +#define SDR0_SRST0_EMAC0 0x00080000 /* Ethernet media access controller 0 */ +#define SDR0_SRST0_EMAC1 0x00040000 /* Ethernet media access controller 1 */ +#define SDR0_SRST0_CPM0 0x00020000 /* Clock and power management */ +#define SDR0_SRST0_ZMII 0x00010000 /* ZMII bridge */ +#define SDR0_SRST0_UIC0 0x00008000 /* Universal interrupt controller 0 */ +#define SDR0_SRST0_UIC1 0x00004000 /* Universal interrupt controller 1 */ +#define SDR0_SRST0_IIC1 0x00002000 /* Inter integrated circuit 1 */ +#define SDR0_SRST0_SCP 0x00001000 /* Serial communications port */ +#define SDR0_SRST0_BGI 0x00000800 /* OPB to PLB bridge */ +#define SDR0_SRST0_DMA 0x00000400 /* Direct memory access controller */ +#define SDR0_SRST0_DMAC 0x00000200 /* DMA channel */ +#define SDR0_SRST0_MAL 0x00000100 /* Media access layer */ +#define SDR0_SRST0_USB2D 0x00000080 /* USB2.0 device */ +#define SDR0_SRST0_GPTR 0x00000040 /* General purpose timer */ +#define SDR0_SRST0_P4P3 0x00000010 /* PLB4 to PLB3 bridge */ +#define SDR0_SRST0_P3P4 0x00000008 /* PLB3 to PLB4 bridge */ +#define SDR0_SRST0_PLB3 0x00000004 /* PLB3 arbiter */ +#define SDR0_SRST0_UART2 0x00000002 /* Universal asynchronous receiver/transmitter 2 */ +#define SDR0_SRST0_UART3 0x00000001 /* Universal asynchronous receiver/transmitter 3 */ + +#define SDR0_SRST1 0x201 +#define SDR0_SRST1_NDFC 0x80000000 /* Nand flash controller */ +#define SDR0_SRST1_OPBA1 0x40000000 /* OPB Arbiter attached to PLB4 */ +#define SDR0_SRST1_P4OPB0 0x20000000 /* PLB4 to OPB Bridge0 */ +#define SDR0_SRST1_PLB42OPB0 SDR0_SRST1_P4OPB0 +#define SDR0_SRST1_DMA4 0x10000000 /* DMA to PLB4 */ +#define SDR0_SRST1_DMA4CH 0x08000000 /* DMA Channel to PLB4 */ +#define SDR0_SRST1_OPBA2 0x04000000 /* OPB Arbiter attached to PLB4 USB 2.0 Host */ +#define SDR0_SRST1_OPB2PLB40 0x02000000 /* OPB to PLB4 Bridge attached to USB 2.0 Host */ +#define SDR0_SRST1_PLB42OPB1 0x01000000 /* PLB4 to OPB Bridge attached to USB 2.0 Host */ +#define SDR0_SRST1_CPM1 0x00800000 /* Clock and Power management 1 */ +#define SDR0_SRST1_UIC2 0x00400000 /* Universal Interrupt Controller 2 */ +#define SDR0_SRST1_CRYP0 0x00200000 /* Security Engine */ +#define SDR0_SRST1_USB20PHY 0x00100000 /* USB 2.0 Phy */ +#define SDR0_SRST1_USB2HUTMI 0x00080000 /* USB 2.0 Host UTMI Interface */ +#define SDR0_SRST1_USB2HPHY 0x00040000 /* USB 2.0 Host Phy Interface */ +#define SDR0_SRST1_SRAM0 0x00020000 /* Internal SRAM Controller */ +#define SDR0_SRST1_RGMII0 0x00010000 /* RGMII Bridge */ +#define SDR0_SRST1_ETHPLL 0x00008000 /* Ethernet PLL */ +#define SDR0_SRST1_FPU 0x00004000 /* Floating Point Unit */ +#define SDR0_SRST1_KASU0 0x00002000 /* Kasumi Engine */ + +#else #define SDR0_SRST_BGO 0x80000000 #define SDR0_SRST_PLB 0x40000000 @@ -2427,10 +2832,15 @@ #define SDR0_SRST_EMAC3 0x00000008 #define SDR0_SRST_RGMII 0x00000001 +#endif + /*-----------------------------------------------------------------------------+ | Clocking +-----------------------------------------------------------------------------*/ -#if !defined (CONFIG_440GX) && !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) +#if !defined (CONFIG_440GX) && \ + !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \ + !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) #define PLLSYS0_TUNE_MASK 0xffc00000 /* PLL TUNE bits */ #define PLLSYS0_FB_DIV_MASK 0x003c0000 /* Feedback divisor */ #define PLLSYS0_FWD_DIV_A_MASK 0x00038000 /* Forward divisor A */ @@ -2498,6 +2908,120 @@ #define PLLSYS1_NTO1_MASK 0x00000001 /* CPU:PLB N-to-1 ratio */ #endif /* CONFIG_440GX */ +#if defined (CONFIG_440EPX) || defined (CONFIG_440GRX) +/*--------------------------------------*/ +#define CPR0_PLLC 0x40 +#define CPR0_PLLC_RST_MASK 0x80000000 +#define CPR0_PLLC_RST_PLLLOCKED 0x00000000 +#define CPR0_PLLC_RST_PLLRESET 0x80000000 +#define CPR0_PLLC_ENG_MASK 0x40000000 +#define CPR0_PLLC_ENG_DISABLE 0x00000000 +#define CPR0_PLLC_ENG_ENABLE 0x40000000 +#define CPR0_PLLC_ENG_ENCODE(n) ((((unsigned long)(n))&0x01)<<30) +#define CPR0_PLLC_ENG_DECODE(n) ((((unsigned long)(n))>>30)&0x01) +#define CPR0_PLLC_SRC_MASK 0x20000000 +#define CPR0_PLLC_SRC_PLLOUTA 0x00000000 +#define CPR0_PLLC_SRC_PLLOUTB 0x20000000 +#define CPR0_PLLC_SRC_ENCODE(n) ((((unsigned long)(n))&0x01)<<29) +#define CPR0_PLLC_SRC_DECODE(n) ((((unsigned long)(n))>>29)&0x01) +#define CPR0_PLLC_SEL_MASK 0x07000000 +#define CPR0_PLLC_SEL_PLL 0x00000000 +#define CPR0_PLLC_SEL_CPU 0x01000000 +#define CPR0_PLLC_SEL_PER 0x05000000 +#define CPR0_PLLC_SEL_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PLLC_SEL_DECODE(n) ((((unsigned long)(n))>>24)&0x07) +#define CPR0_PLLC_TUNE_MASK 0x000003FF +#define CPR0_PLLC_TUNE_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) +#define CPR0_PLLC_TUNE_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) +/*--------------------------------------*/ +#define CPR0_PLLD 0x60 +#define CPR0_PLLD_FBDV_MASK 0x1F000000 +#define CPR0_PLLD_FBDV_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define CPR0_PLLD_FBDV_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x1F)+1) +#define CPR0_PLLD_FWDVA_MASK 0x000F0000 +#define CPR0_PLLD_FWDVA_ENCODE(n) ((((unsigned long)(n))&0x0F)<<16) +#define CPR0_PLLD_FWDVA_DECODE(n) ((((((unsigned long)(n))>>16)-1)&0x0F)+1) +#define CPR0_PLLD_FWDVB_MASK 0x00000700 +#define CPR0_PLLD_FWDVB_ENCODE(n) ((((unsigned long)(n))&0x07)<<8) +#define CPR0_PLLD_FWDVB_DECODE(n) ((((((unsigned long)(n))>>8)-1)&0x07)+1) +#define CPR0_PLLD_LFBDV_MASK 0x0000003F +#define CPR0_PLLD_LFBDV_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) +#define CPR0_PLLD_LFBDV_DECODE(n) ((((((unsigned long)(n))>>0)-1)&0x3F)+1) +/*--------------------------------------*/ +#define CPR0_PRIMAD 0x80 +#define CPR0_PRIMAD_PRADV0_MASK 0x07000000 +#define CPR0_PRIMAD_PRADV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PRIMAD_PRADV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#define CPR0_PRIMBD 0xA0 +#define CPR0_PRIMBD_PRBDV0_MASK 0x07000000 +#define CPR0_PRIMBD_PRBDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PRIMBD_PRBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#if 0 +#define CPR0_CPM0_ER 0xB0 /* CPM Enable Register */ +#define CPR0_CPM0_FR 0xB1 /* CPM Force Register */ +#define CPR0_CPM0_SR 0xB2 /* CPM Status Register */ +#define CPR0_CPM0_IIC0 0x80000000 /* Inter-Intergrated Circuit0 */ +#define CPR0_CPM0_IIC1 0x40000000 /* Inter-Intergrated Circuit1 */ +#define CPR0_CPM0_PCI 0x20000000 /* Peripheral Component Interconnect */ +#define CPR0_CPM0_USB1H 0x08000000 /* USB1.1 Host */ +#define CPR0_CPM0_FPU 0x04000000 /* PPC440 FPU */ +#define CPR0_CPM0_CPU 0x02000000 /* PPC440x5 Processor Core */ +#define CPR0_CPM0_DMA 0x01000000 /* Direct Memory Access Controller */ +#define CPR0_CPM0_BGO 0x00800000 /* PLB to OPB Bridge */ +#define CPR0_CPM0_BGI 0x00400000 /* OPB to PLB Bridge */ +#define CPR0_CPM0_EBC 0x00200000 /* External Bus Controller */ +#define CPR0_CPM0_NDFC 0x00100000 /* Nand Flash Controller */ +#define CPR0_CPM0_MADMAL 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ +#define CPR0_CPM0_DMC 0x00080000 /* DDR SDRAM Controller or MADMAL ??? */ +#define CPR0_CPM0_PLB4 0x00040000 /* PLB4 Arbiter */ +#define CPR0_CPM0_PLB4x3x 0x00020000 /* PLB4 to PLB3 */ +#define CPR0_CPM0_PLB3x4x 0x00010000 /* PLB3 to PLB4 */ +#define CPR0_CPM0_PLB3 0x00008000 /* PLB3 Arbiter */ +#define CPR0_CPM0_PPM 0x00002000 /* PLB Performance Monitor */ +#define CPR0_CPM0_UIC1 0x00001000 /* Universal Interrupt Controller 1 */ +#define CPR0_CPM0_GPIO 0x00000800 /* General Purpose IO */ +#define CPR0_CPM0_GPT 0x00000400 /* General Purpose Timer */ +#define CPR0_CPM0_UART0 0x00000200 /* Universal Asynchronous Rcver/Xmitter 0 */ +#define CPR0_CPM0_UART1 0x00000100 /* Universal Asynchronous Rcver/Xmitter 1 */ +#define CPR0_CPM0_UIC0 0x00000080 /* Universal Interrupt Controller 0 */ +#define CPR0_CPM0_TMRCLK 0x00000040 /* CPU Timer */ +#define CPR0_CPM0_EMC0 0x00000020 /* Ethernet 0 */ +#define CPR0_CPM0_EMC1 0x00000010 /* Ethernet 1 */ +#define CPR0_CPM0_UART2 0x00000008 /* Universal Asynchronous Rcver/Xmitter 2 */ +#define CPR0_CPM0_UART3 0x00000004 /* Universal Asynchronous Rcver/Xmitter 3 */ +#define CPR0_CPM0_USB2D 0x00000002 /* USB2.0 Device */ +#define CPR0_CPM0_USB2H 0x00000001 /* USB2.0 Host */ +#endif +/*--------------------------------------*/ +#define CPR0_OPBD 0xC0 +#define CPR0_OPBD_OPBDV0_MASK 0x03000000 +#define CPR0_OPBD_OPBDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_OPBD_OPBDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_PERD 0xE0 +#define CPR0_PERD_PERDV0_MASK 0x07000000 +#define CPR0_PERD_PERDV0_ENCODE(n) ((((unsigned long)(n))&0x07)<<24) +#define CPR0_PERD_PERDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x07)+1) +/*--------------------------------------*/ +#define CPR0_MALD 0x100 +#define CPR0_MALD_MALDV0_MASK 0x03000000 +#define CPR0_MALD_MALDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_MALD_MALDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_SPCID 0x120 +#define CPR0_SPCID_SPCIDV0_MASK 0x03000000 +#define CPR0_SPCID_SPCIDV0_ENCODE(n) ((((unsigned long)(n))&0x03)<<24) +#define CPR0_SPCID_SPCIDV0_DECODE(n) ((((((unsigned long)(n))>>24)-1)&0x03)+1) +/*--------------------------------------*/ +#define CPR0_ICFG 0x140 +#define CPR0_ICFG_RLI_MASK 0x80000000 +#define CPR0_ICFG_RLI_RESETCPR 0x00000000 +#define CPR0_ICFG_RLI_PRESERVECPR 0x80000000 +#define CPR0_ICFG_ICS_MASK 0x00000007 +#endif /* defined (CONFIG_440EPX) || defined (CONFIG_440GRX) */ + /*----------------------------------------------------------------------------- | IIC Register Offsets '----------------------------------------------------------------------------*/ @@ -2539,7 +3063,8 @@ #define PCIX0_CFGBASE (CFG_PCI_BASE + 0x0ec80000) #define PCIX0_IOBASE (CFG_PCI_BASE + 0x08000000) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* PCI Local Configuration Registers --------------------------------- */ @@ -2625,6 +3150,33 @@ #endif /* !defined(CONFIG_440EP) !defined(CONFIG_440GR) */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +/* USB2.0 Device */ +#define USB2D0_BASE CFG_USB2D0_BASE + +#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) + +#define USB2D0_INTRIN (USB2D0_BASE + 0x00000000) /* Interrupt register for Endpoint 0 plus IN Endpoints 1 to 3 */ +#define USB2D0_POWER (USB2D0_BASE + 0x00000000) /* Power management register */ +#define USB2D0_FADDR (USB2D0_BASE + 0x00000000) /* Function address register */ +#define USB2D0_INTRINE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRIN */ +#define USB2D0_INTROUT (USB2D0_BASE + 0x00000000) /* Interrupt register for OUT Endpoints 1 to 3 */ +#define USB2D0_INTRUSBE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for USB2D0_INTRUSB */ +#define USB2D0_INTRUSB (USB2D0_BASE + 0x00000000) /* Interrupt register for common USB interrupts */ +#define USB2D0_INTROUTE (USB2D0_BASE + 0x00000000) /* Interrupt enable register for IntrOut */ +#define USB2D0_TSTMODE (USB2D0_BASE + 0x00000000) /* Enables the USB 2.0 test modes */ +#define USB2D0_INDEX (USB2D0_BASE + 0x00000000) /* Index register for selecting the Endpoint status/control registers */ +#define USB2D0_FRAME (USB2D0_BASE + 0x00000000) /* Frame number */ +#define USB2D0_INCSR0 (USB2D0_BASE + 0x00000000) /* Control Status register for Endpoint 0. (Index register set to select Endpoint 0) */ +#define USB2D0_INCSR (USB2D0_BASE + 0x00000000) /* Control Status register for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_INMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for IN Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCSR (USB2D0_BASE + 0x00000000) /* Control Status register for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTMAXP (USB2D0_BASE + 0x00000000) /* Maximum packet size for OUT Endpoint. (Index register set to select Endpoints 13) */ +#define USB2D0_OUTCOUNT0 (USB2D0_BASE + 0x00000000) /* Number of received bytes in Endpoint 0 FIFO. (Index register set to select Endpoint 0) */ +#define USB2D0_OUTCOUNT (USB2D0_BASE + 0x00000000) /* Number of bytes in OUT Endpoint FIFO. (Index register set to select Endpoints 13) */ +#endif + /****************************************************************************** * GPIO macro register defines ******************************************************************************/ @@ -2640,7 +3192,8 @@ #define GPIO0_IR (GPIO0_BASE+0x1C) #endif /* CONFIG_440GP */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000B00) #define GPIO1_BASE (CFG_PERIPHERAL_BASE+0x00000C00) diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index ec2e3629bb8..43c5ca451e0 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -145,12 +145,14 @@ typedef struct emac_4xx_hw_st { #define EMAC_STACR_OC_MASK (0x00000000) #endif -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_PFC1_EM_1000 (0x00200000) #endif /*ZMII Bridge Register addresses */ -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define ZMII_BASE (CFG_PERIPHERAL_BASE + 0x0D00) #else #define ZMII_BASE (CFG_PERIPHERAL_BASE + 0x0780) @@ -163,6 +165,7 @@ typedef struct emac_4xx_hw_st { #define ZMII_MDI0 0x80000000 /* ZMII FER Register Bit Definitions */ +#define ZMII_FER_DIS (0x0) #define ZMII_FER_MDI (0x8) #define ZMII_FER_SMII (0x4) #define ZMII_FER_RMII (0x2) @@ -197,7 +200,11 @@ typedef struct emac_4xx_hw_st { #define ZMII_SMIISR_V(__x) ((3 - __x) * 8) /* RGMII Register Addresses */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x1000) +#else #define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x0790) +#endif #define RGMII_FER (RGMII_BASE + 0x00) #define RGMII_SSR (RGMII_BASE + 0x04) @@ -216,7 +223,11 @@ typedef struct emac_4xx_hw_st { #define RGMII_SSR_SP_100MBPS (0x02) #define RGMII_SSR_SP_1000MBPS (0x04) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#define RGMII_SSR_V(__x) ((__x) * 8) +#else #define RGMII_SSR_V(__x) ((__x -2) * 8) +#endif /*---------------------------------------------------------------------------+ @@ -286,7 +297,8 @@ typedef struct emac_4xx_hw_st { /* Ethernet MAC Regsiter Addresses */ #if defined(CONFIG_440) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define EMAC_BASE (CFG_PERIPHERAL_BASE + 0x0E00) #else #define EMAC_BASE (CFG_PERIPHERAL_BASE + 0x0800) @@ -332,7 +344,9 @@ typedef struct emac_4xx_hw_st { #define EMAC_M0_WKE (0x04000000) /* on 440GX EMAC_MR1 has a different layout! */ -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* MODE Reg 1 */ #define EMAC_M1_FDE (0x80000000) #define EMAC_M1_ILE (0x40000000) diff --git a/include/ppc_asm.tmpl b/include/ppc_asm.tmpl index 72d690ef0f8..3e47e82abad 100644 --- a/include/ppc_asm.tmpl +++ b/include/ppc_asm.tmpl @@ -312,7 +312,7 @@ label: \ lwz r3,GOT(transfer_to_handler); \ mtlr r3; \ addi r3,r1,STACK_FRAME_OVERHEAD; \ - li r20,MSR_KERNEL; \ + li r20,(MSR_KERNEL & ~(MSR_ME|MSR_DE|MSR_CE)); \ rlwimi r20,r23,0,25,25; \ blrl ; \ .L_ ## label : \ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index db80f775603..cf0e3fdf4b6 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -763,6 +763,12 @@ void board_init_r (gd_t *id, ulong dest_addr) spi_init_r (); #endif +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + WATCHDOG_RESET (); + puts ("NAND: "); + nand_init(); /* go init the NAND */ +#endif + /* relocate environment function pointers etc. */ env_relocate (); @@ -959,12 +965,6 @@ void board_init_r (gd_t *id, ulong dest_addr) doc_init (); #endif -#if (CONFIG_COMMANDS & CFG_CMD_NAND) - WATCHDOG_RESET (); - puts ("NAND: "); - nand_init(); /* go init the NAND */ -#endif - #if (CONFIG_COMMANDS & CFG_CMD_NET) #if defined(CONFIG_NET_MULTI) WATCHDOG_RESET (); diff --git a/nand_spl/board/amcc/sequoia/Makefile b/nand_spl/board/amcc/sequoia/Makefile new file mode 100644 index 00000000000..6c07e3dd8df --- /dev/null +++ b/nand_spl/board/amcc/sequoia/Makefile @@ -0,0 +1,83 @@ +# +# (C) Copyright 2006 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +include board/$(BOARDDIR)/config.mk + +LDSCRIPT= board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o init.o resetvec.o +COBJS = nand_boot.o ndfc.o sdram.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +ALL = u-boot-spl u-boot-spl.bin u-boot-spl-4k.bin + +all: $(obj).depend $(ALL) + +u-boot-spl-4k.bin: u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +u-boot-spl.bin: u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +u-boot-spl: $(OBJS) + $(LD) $(LDFLAGS) $$UNDEF_SYM $(OBJS) \ + -Map u-boot-spl.map -o u-boot-spl + +# create symbolic links for common files + +# from cpu directory +ndfc.c: + @rm -f ndfc.c + ln -s ../cpu/ppc4xx/ndfc.c ndfc.c + +resetvec.S: + @rm -f resetvec.S + ln -s ../cpu/ppc4xx/resetvec.S resetvec.S + +start.S: + @rm -f start.S + ln -s ../cpu/ppc4xx/start.S start.S + +# from board directory +init.S: + @rm -f init.S + ln -s ../board/amcc/sequoia/init.S init.S + +sdram.c: + @rm -f sdram.c + ln -s ../board/amcc/sequoia/sdram.c sdram.c + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/amcc/sequoia/config.mk b/nand_spl/board/amcc/sequoia/config.mk new file mode 100644 index 00000000000..a29ba5fd0dc --- /dev/null +++ b/nand_spl/board/amcc/sequoia/config.mk @@ -0,0 +1,49 @@ +# +# (C) Copyright 2006 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# +# AMCC 440EPx Reference Platform (Sequoia) board +# + +# +# TEXT_BASE for SPL: +# +# On 440EP(x) platforms the SPL is located at 0xfffff000...0xffffffff, +# in the last 4kBytes of memory space in cache. +# We will copy this SPL into internal SRAM in start.S. So we set +# TEXT_BASE to starting address in internal SRAM here. +# +TEXT_BASE = 0xE0013000 + +# PAD_TO used to generate a 16kByte binary needed for the combined image +# -> PAD_TO = TEXT_BASE + 0x4000 +PAD_TO = 0xE0017000 + +PLATFORM_CPPFLAGS += -DCONFIG_440=1 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 +endif diff --git a/nand_spl/board/amcc/sequoia/u-boot.lds b/nand_spl/board/amcc/sequoia/u-boot.lds new file mode 100644 index 00000000000..156368911a2 --- /dev/null +++ b/nand_spl/board/amcc/sequoia/u-boot.lds @@ -0,0 +1,65 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc:common) +SECTIONS +{ + .resetvec 0xE0013FFC : + { + *(.resetvec) + } = 0xffff + + .text : + { + start.o (.text) + init.o (.text) + nand_boot.o (.text) + sdram.o (.text) + ndfc.o (.text) + + *(.text) + *(.fixup) + } + _etext = .; + + .data : + { + *(.rodata*) + *(.data*) + *(.sdata*) + __got2_start = .; + *(.got2) + __got2_end = .; + } + + _edata = .; + + __bss_start = .; + .bss : + { + *(.sbss) + *(.bss) + } + + _end = . ; +} diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c new file mode 100644 index 00000000000..6e3af13939f --- /dev/null +++ b/nand_spl/nand_boot.c @@ -0,0 +1,178 @@ +/* + * (C) Copyright 2006 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#define CFG_NAND_READ_DELAY \ + { volatile int dummy; int i; for (i=0; i<10000; i++) dummy = i; } + +extern void board_nand_init(struct nand_chip *nand); +extern void ndfc_hwcontrol(struct mtd_info *mtdinfo, int cmd); +extern void ndfc_write_byte(struct mtd_info *mtdinfo, u_char byte); +extern u_char ndfc_read_byte(struct mtd_info *mtdinfo); +extern int ndfc_dev_ready(struct mtd_info *mtdinfo); +extern int jump_to_ram(ulong delta); +extern int jump_to_uboot(ulong addr); + +static int nand_is_bad_block(struct mtd_info *mtd, int block) +{ + struct nand_chip *this = mtd->priv; + int page_addr = block * CFG_NAND_PAGE_COUNT; + + /* Begin command latch cycle */ + this->hwcontrol(mtd, NAND_CTL_SETCLE); + this->write_byte(mtd, NAND_CMD_READOOB); + /* Set ALE and clear CLE to start address cycle */ + this->hwcontrol(mtd, NAND_CTL_CLRCLE); + this->hwcontrol(mtd, NAND_CTL_SETALE); + /* Column address */ + this->write_byte(mtd, CFG_NAND_BAD_BLOCK_POS); /* A[7:0] */ + this->write_byte(mtd, (uchar)(page_addr & 0xff)); /* A[16:9] */ + this->write_byte(mtd, (uchar)((page_addr >> 8) & 0xff)); /* A[24:17] */ +#ifdef CFG_NAND_4_ADDR_CYCLE + /* One more address cycle for devices > 32MiB */ + this->write_byte(mtd, (uchar)((page_addr >> 16) & 0x0f)); /* A[xx:25] */ +#endif + /* Latch in address */ + this->hwcontrol(mtd, NAND_CTL_CLRALE); + + /* + * Wait a while for the data to be ready + */ + if (this->dev_ready) + this->dev_ready(mtd); + else + CFG_NAND_READ_DELAY; + + /* + * Read on byte + */ + if (this->read_byte(mtd) != 0xff) + return 1; + + return 0; +} + +static int nand_read_page(struct mtd_info *mtd, int block, int page, uchar *dst) +{ + struct nand_chip *this = mtd->priv; + int page_addr = page + block * CFG_NAND_PAGE_COUNT; + int i; + + /* Begin command latch cycle */ + this->hwcontrol(mtd, NAND_CTL_SETCLE); + this->write_byte(mtd, NAND_CMD_READ0); + /* Set ALE and clear CLE to start address cycle */ + this->hwcontrol(mtd, NAND_CTL_CLRCLE); + this->hwcontrol(mtd, NAND_CTL_SETALE); + /* Column address */ + this->write_byte(mtd, 0); /* A[7:0] */ + this->write_byte(mtd, (uchar)(page_addr & 0xff)); /* A[16:9] */ + this->write_byte(mtd, (uchar)((page_addr >> 8) & 0xff)); /* A[24:17] */ +#ifdef CFG_NAND_4_ADDR_CYCLE + /* One more address cycle for devices > 32MiB */ + this->write_byte(mtd, (uchar)((page_addr >> 16) & 0x0f)); /* A[xx:25] */ +#endif + /* Latch in address */ + this->hwcontrol(mtd, NAND_CTL_CLRALE); + + /* + * Wait a while for the data to be ready + */ + if (this->dev_ready) + this->dev_ready(mtd); + else + CFG_NAND_READ_DELAY; + + /* + * Read page into buffer + */ + for (i=0; iread_byte(mtd); + + return 0; +} + +static int nand_load(struct mtd_info *mtd, int offs, int uboot_size, uchar *dst) +{ + int block; + int blockcopy_count; + int page; + + /* + * offs has to be aligned to a block address! + */ + block = offs / CFG_NAND_BLOCK_SIZE; + blockcopy_count = 0; + + while (blockcopy_count < (uboot_size / CFG_NAND_BLOCK_SIZE)) { + if (!nand_is_bad_block(mtd, block)) { + /* + * Skip bad blocks + */ + for (page = 0; page < CFG_NAND_PAGE_COUNT; page++) { + nand_read_page(mtd, block, page, dst); + dst += CFG_NAND_PAGE_SIZE; + } + + blockcopy_count++; + } + + block++; + } + + return 0; +} + +void nand_boot(void) +{ + ulong mem_size; + struct nand_chip nand_chip; + nand_info_t nand_info; + int ret; + void (*uboot)(void); + + /* + * Init sdram, so we have access to memory + */ + mem_size = initdram(0); + + /* + * Init board specific nand support + */ + nand_info.priv = &nand_chip; + nand_chip.IO_ADDR_R = nand_chip.IO_ADDR_W = (void __iomem *)CFG_NAND_BASE; + nand_chip.dev_ready = NULL; /* preset to NULL */ + board_nand_init(&nand_chip); + + /* + * Load U-Boot image from NAND into RAM + */ + ret = nand_load(&nand_info, CFG_NAND_U_BOOT_OFFS, + CFG_NAND_U_BOOT_SIZE, + (uchar *)CFG_NAND_U_BOOT_DST); + + /* + * Jump to U-Boot image + */ + uboot = (void (*)(void))CFG_NAND_U_BOOT_START; + (*uboot)(); +} -- cgit v1.3.1 From a73c8dbb437fb55ecb660cb962c8c1cc85b8a654 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 12 Sep 2006 08:49:07 +0200 Subject: Update NAND boot documentation Patch by Stefan Roese, 12 Sep 2006 --- CHANGELOG | 5 ++++- Makefile | 4 ++-- doc/README.nand-boot-ppc440 | 24 ++++++++++++++++++++++++ nand_spl/board/amcc/sequoia/Makefile | 4 ++-- 4 files changed, 32 insertions(+), 5 deletions(-) (limited to 'doc') diff --git a/CHANGELOG b/CHANGELOG index 4265049a2e9..a6dc7623483 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,7 +2,10 @@ Changes since U-Boot 1.1.4: ====================================================================== -* Add documentation on the latest build environment extensions to +* Update NAND boot documentation + Patch by Stefan Roese, 12 Sep 2006 + +* Add documentation on the latest build environment extensions to the README file. * Remove dead code (i2o and dma) from cpu/mpc824x/drivers/ directory. diff --git a/Makefile b/Makefile index 291dc61055f..84d936701f8 100644 --- a/Makefile +++ b/Makefile @@ -78,7 +78,7 @@ saved-output := $(BUILD_DIR) # Attempt to create a output directory. $(shell [ -d ${BUILD_DIR} ] || mkdir -p ${BUILD_DIR}) -# Verify if it was successful. +# Verify if it was successful. BUILD_DIR := $(shell cd $(BUILD_DIR) && /bin/pwd) $(if $(BUILD_DIR),,$(error output directory "$(saved-output)" does not exist)) endif # ifneq ($(BUILD_DIR),) @@ -272,7 +272,7 @@ $(NAND_SPL): version $(MAKE) -C nand_spl all $(U_BOOT_NAND): $(NAND_SPL) $(obj)u-boot.bin - cat nand_spl/u-boot-spl-4k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin + cat nand_spl/u-boot-spl-16k.bin $(obj)u-boot.bin > $(obj)u-boot-nand.bin version: @echo -n "#define U_BOOT_VERSION \"U-Boot " > $(VERSION_FILE); \ diff --git a/doc/README.nand-boot-ppc440 b/doc/README.nand-boot-ppc440 index a82a10ee6a5..a1c1d8c4447 100644 --- a/doc/README.nand-boot-ppc440 +++ b/doc/README.nand-boot-ppc440 @@ -33,4 +33,28 @@ is set up. While still running from cache, I experienced problems accessing the NAND controller. +Example: Build and install NAND boot image for Sequoia (440EPx): + +a) Configure for sequoia with NAND boot support: +# make sequoia_nand_config + +b) Build image(s) +# make + +This will generate the SPL image in the "nand_spl" directory: +nand_spl/u-boot-spl.bin +Also another image is created spanning a whole NAND block (16kBytes): +nand_spl/u-boot-spl-16k.bin +The main NAND U-Boot image is generated in the toplevel directory: +u-boot.bin +A combined image of u-boot-spl-16k.bin and u-boot.bin is also created: +u-boot-nand.bin + +This image should be programmed at offset 0 in the NAND flash: + +# tftp 100000 /tftpboot/sequoia/u-boot-nand.bin +# nand erase 0 60000 +# nand write 100000 0 60000 + + September 07 2006, Stefan Roese diff --git a/nand_spl/board/amcc/sequoia/Makefile b/nand_spl/board/amcc/sequoia/Makefile index 6c07e3dd8df..897aa8b6b70 100644 --- a/nand_spl/board/amcc/sequoia/Makefile +++ b/nand_spl/board/amcc/sequoia/Makefile @@ -35,11 +35,11 @@ COBJS = nand_boot.o ndfc.o sdram.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) -ALL = u-boot-spl u-boot-spl.bin u-boot-spl-4k.bin +ALL = u-boot-spl u-boot-spl.bin u-boot-spl-16k.bin all: $(obj).depend $(ALL) -u-boot-spl-4k.bin: u-boot-spl +u-boot-spl-16k.bin: u-boot-spl $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ u-boot-spl.bin: u-boot-spl -- cgit v1.3.1 From 2255b2d2044d434463eb2661e18018e50f1643d9 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 10 Oct 2006 12:36:02 +0200 Subject: * Several improvements to the new NAND subsystem: - JFFS2 related commands implemented in mtd-utils style - Support for bad blocks - Bad block testing commands - NAND lock commands Please take a look at doc/README.nand for more details Patch by Guido Classen, 10 Oct 2006 --- CHANGELOG | 8 + common/cmd_nand.c | 226 ++++++++++-- doc/README.nand | 44 +++ drivers/nand/Makefile | 2 +- drivers/nand/nand_util.c | 869 +++++++++++++++++++++++++++++++++++++++++++++++ include/nand.h | 57 ++++ lib_generic/crc32.c | 4 +- 7 files changed, 1183 insertions(+), 27 deletions(-) create mode 100644 drivers/nand/nand_util.c (limited to 'doc') diff --git a/CHANGELOG b/CHANGELOG index a2ea35d68e3..9ed65bdbfe4 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,14 @@ Changes since U-Boot 1.1.4: ====================================================================== +* Several improvements to the new NAND subsystem: + - JFFS2 related commands implemented in mtd-utils style + - Support for bad blocks + - Bad block testing commands + - NAND lock commands + Please take a look at doc/README.nand for more details + Patch by Guido Classen, 10 Oct 2006 + * Define IH_CPU_AVR32 Make it possible to generate AVR32 uImage files with mkimage and make cmd_bootm recognize them. diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 21adb1b4786..274ef0b9938 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -135,11 +135,16 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) ulong addr, off, size; char *cmd, *s; nand_info_t *nand; + int quiet = 0; + const char *quiet_str = getenv("quiet"); /* at least two arguments please */ if (argc < 2) goto usage; + if (quiet_str) + quiet = simple_strtoul(quiet_str, NULL, 0) != 0; + cmd = argv[1]; if (strcmp(cmd, "info") == 0) { @@ -178,7 +183,10 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) if (strcmp(cmd, "bad") != 0 && strcmp(cmd, "erase") != 0 && strncmp(cmd, "dump", 4) != 0 && - strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0) + strncmp(cmd, "read", 4) != 0 && strncmp(cmd, "write", 5) != 0 && + strcmp(cmd, "scrub") != 0 && strcmp(cmd, "markbad") != 0 && + strcmp(cmd, "biterr") != 0 && + strcmp(cmd, "lock") != 0 && strcmp(cmd, "unlock") != 0 ) goto usage; /* the following commands operate on the current device */ @@ -197,14 +205,64 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) return 0; } - if (strcmp(cmd, "erase") == 0) { - arg_off_size(argc - 2, argv + 2, &off, &size, nand->size); - if (off == 0 && size == 0) - return 1; + if (strcmp(cmd, "erase") == 0 || strcmp(cmd, "scrub") == 0) { + nand_erase_options_t opts; + int clean = argc >= 3 && !strcmp("clean", argv[2]); + int rest_argc = argc - 2; + char **rest_argv = argv + 2; + int scrub = !strcmp(cmd, "scrub"); + + if (clean) { + rest_argc--; + rest_argv++; + } + + if (rest_argc == 0) { - printf("\nNAND erase: device %d offset 0x%x, size 0x%x ", - nand_curr_device, off, size); - ret = nand_erase(nand, off, size); + printf("\nNAND %s: device %d whole chip\n", + cmd, + nand_curr_device); + + off = size = 0; + } else { + arg_off_size(rest_argc, rest_argv, &off, &size, + nand->size); + + if (off == 0 && size == 0) + return 1; + + printf("\nNAND %s: device %d offset 0x%x, size 0x%x\n", + cmd, nand_curr_device, off, size); + } + + memset(&opts, 0, sizeof(opts)); + opts.offset = off; + opts.length = size; + opts.jffs2 = clean; + opts.quiet = quiet; + + if (scrub) { + printf("Warning: " + "scrub option will erase all factory set " + "bad blocks!\n" + " " + "There is no reliable way to recover them.\n" + " " + "Use this command only for testing purposes " + "if you\n" + " " + "are shure of what you are doing!\n" + "\nReally scrub this NAND flash? \n" + ); + + if (getc() == 'y' && getc() == '\r') { + opts.scrub = 1; + } else { + printf("scrub aborted\n"); + return -1; + } + } + ret = nand_erase_opts(nand, &opts); printf("%s\n", ret ? "ERROR" : "OK"); return ret == 0 ? 0 : 1; @@ -228,37 +286,153 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) /* read write */ if (strncmp(cmd, "read", 4) == 0 || strncmp(cmd, "write", 5) == 0) { + int read; + if (argc < 4) goto usage; -/* - s = strchr(cmd, '.'); - clean = CLEAN_NONE; - if (s != NULL) { - if (strcmp(s, ".jffs2") == 0 || strcmp(s, ".e") == 0 - || strcmp(s, ".i")) - clean = CLEAN_JFFS2; - } -*/ + addr = (ulong)simple_strtoul(argv[2], NULL, 16); arg_off_size(argc - 3, argv + 3, &off, &size, nand->size); if (off == 0 && size == 0) return 1; - i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ + read = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ printf("\nNAND %s: device %d offset %u, size %u ... ", - i ? "read" : "write", nand_curr_device, off, size); + read ? "read" : "write", nand_curr_device, off, size); - if (i) + s = strchr(cmd, '.'); + if (s != NULL && + (!strcmp(s, ".jffs2") || !strcmp(s, ".e") || !strcmp(s, ".i"))) { + if (read) { + /* read */ + nand_read_options_t opts; + memset(&opts, 0, sizeof(opts)); + opts.buffer = (u_char*) addr; + opts.length = size; + opts.offset = off; + opts.quiet = quiet; + ret = nand_read_opts(nand, &opts); + } else { + /* write */ + nand_write_options_t opts; + memset(&opts, 0, sizeof(opts)); + opts.buffer = (u_char*) addr; + opts.length = size; + opts.offset = off; + /* opts.forcejffs2 = 1; */ + opts.pad = 1; + opts.blockalign = 1; + opts.quiet = quiet; + ret = nand_write_opts(nand, &opts); + } + printf("%s\n", ret ? "ERROR" : "OK"); + return ret == 0 ? 0 : 1; + } + + if (read) ret = nand_read(nand, off, &size, (u_char *)addr); else ret = nand_write(nand, off, &size, (u_char *)addr); printf(" %d bytes %s: %s\n", size, - i ? "read" : "written", ret ? "ERROR" : "OK"); + read ? "read" : "written", ret ? "ERROR" : "OK"); return ret == 0 ? 0 : 1; } + + /* 2006-09-28 gc: implement missing commands */ + if (strcmp(cmd, "markbad") == 0) { + addr = (ulong)simple_strtoul(argv[2], NULL, 16); + + int ret = nand->block_markbad(nand, addr); + if (ret == 0) { + printf("block 0x%08lx successfully marked as bad\n", + (ulong) addr); + return 0; + } else { + printf("block 0x%08lx NOT marked as bad! ERROR %d\n", + (ulong) addr, ret); + } + return 1; + } + if (strcmp(cmd, "biterr") == 0) { + /* todo */ + return 1; + } + + if (strcmp(cmd, "lock") == 0) { + int tight = 0; + int status = 0; + if (argc == 3) { + if (!strcmp("tight", argv[2])) + tight = 1; + if (!strcmp("status", argv[2])) + status = 1; + } + + if (status) { + ulong block_start = 0; + ulong off; + int last_status = -1; + + struct nand_chip *nand_chip = nand->priv; + /* check the WP bit */ + nand_chip->cmdfunc (nand, NAND_CMD_STATUS, -1, -1); + printf("device is %swrite protected\n", + (nand_chip->read_byte(nand) & 0x80 ? + "NOT " : "" ) ); + + for (off = 0; off < nand->size; off += nand->oobblock) { + int s = nand_get_lock_status(nand, off); + + /* print message only if status has changed + * or at end of chip + */ + if (off == nand->size - nand->oobblock + || (s != last_status && off != 0)) { + + printf("%08x - %08x: %8d pages %s%s%s\n", + block_start, + off-1, + (off-block_start)/nand->oobblock, + ((last_status & NAND_LOCK_STATUS_TIGHT) ? "TIGHT " : ""), + ((last_status & NAND_LOCK_STATUS_LOCK) ? "LOCK " : ""), + ((last_status & NAND_LOCK_STATUS_UNLOCK) ? "UNLOCK " : "")); + } + + last_status = s; + } + } else { + if (!nand_lock(nand, tight)) { + printf ("NAND flash successfully locked\n"); + } else { + printf ("Error locking NAND flash. \n"); + return 1; + } + } + return 0; + } + + if (strcmp(cmd, "unlock") == 0) { + if (argc == 2) { + off = 0; + size = nand->size; + } else { + arg_off_size(argc - 2, argv + 2, &off, &size, + nand->size); + } + + if (!nand_unlock(nand, off, size)) { + printf("NAND flash successfully unlocked\n"); + } else { + printf("Error unlocking NAND flash. " + "Write and erase will probably fail\n"); + return 1; + } + return 0; + } + usage: printf("Usage:\n%s\n", cmdtp->usage); return 1; @@ -277,7 +451,9 @@ U_BOOT_CMD(nand, 5, 1, do_nand, "nand dump[.oob] off - dump page\n" "nand scrub - really clean NAND erasing bad blocks (UNSAFE)\n" "nand markbad off - mark bad block at offset (UNSAFE)\n" - "nand biterr off - make a bit error at offset (UNSAFE)\n"); + "nand biterr off - make a bit error at offset (UNSAFE)\n" + "nand lock [tight] [status] - bring nand to lock state or display locked pages\n" + "nand unlock [offset] [size] - unlock section\n"); int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) { @@ -596,7 +772,7 @@ int do_nand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) return 1; } - printf ("\nNAND %s: device %d offset %ld, size %ld ... ", + printf ("\nNAND %s: device %d offset %ld, size %ld ...\n", (cmd & NANDRW_READ) ? "read" : "write", curr_device, off, size); @@ -615,7 +791,7 @@ int do_nand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) ulong size = simple_strtoul(argv[3 + clean], NULL, 16); int ret; - printf ("\nNAND erase: device %d offset %ld, size %ld ... ", + printf ("\nNAND erase: device %d offset %ld, size %ld ...\n", curr_device, off, size); ret = nand_legacy_erase (nand_dev_desc + curr_device, @@ -635,7 +811,7 @@ int do_nand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( nand, 5, 1, do_nand, - "nand - NAND sub-system\n", + "nand - legacy NAND sub-system\n", "info - show available NAND devices\n" "nand device [dev] - show or set current device\n" "nand read[.jffs2[s]] addr off size\n" diff --git a/doc/README.nand b/doc/README.nand index f2d6a5b1e65..2b9a52966c5 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -207,3 +207,47 @@ As mentioned above, the legacy code is still used by the DoC subsystem. The consequence of this is that the legacy NAND can't be removed from the tree until the DoC is ported to use the new NAND support (or boards with DoC will break). + + + +Additional improvements to the NAND subsystem by Guido Classen, 10-10-2006 + +JFFS2 related commands: + + implement "nand erase clean" and old "nand erase" + using both the new code which is able to skip bad blocks + "nand erase clean" additionally writes JFFS2-cleanmarkers in the oob. + + "nand write.jffs2" + like "nand write" but skip found bad eraseblocks + + "nand read.jffs2" + like "nand read" but skip found bad eraseblocks + +Miscellaneous and testing commands: + "markbad [offset]" + create an artificial bad block (for testing bad block handling) + + "scrub [offset length]" + like "erase" but don't skip bad block. Instead erase them. + DANGEROUS!!! Factory set bad blocks will be lost. Use only + to remove artificial bad blocks created with the "markbad" command. + + +NAND locking command (for chips with active LOCKPRE pin) + + "nand lock" + set NAND chip to lock state (all pages locked) + + "nand lock tight" + set NAND chip to lock tight state (software can't change locking anymore) + + "nand lock status" + displays current locking status of all pages + + "nand unlock [offset] [size]" + unlock consecutive area (can be called multiple times for different areas) + + +I have tested the code with board containing 128MiB NAND large page chips +and 32MiB small page chips. diff --git a/drivers/nand/Makefile b/drivers/nand/Makefile index b03604dc4e9..fb0185b991b 100644 --- a/drivers/nand/Makefile +++ b/drivers/nand/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)libnand.a -COBJS := nand.o nand_base.o nand_ids.o nand_ecc.o nand_bbt.o +COBJS := nand.o nand_base.o nand_ids.o nand_ecc.o nand_bbt.o nand_util.o SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/drivers/nand/nand_util.c b/drivers/nand/nand_util.c new file mode 100644 index 00000000000..5a8e58a741c --- /dev/null +++ b/drivers/nand/nand_util.c @@ -0,0 +1,869 @@ +/* + * drivers/nand/nand_util.c + * + * Copyright (C) 2006 by Weiss-Electronic GmbH. + * All rights reserved. + * + * @author: Guido Classen + * @descr: NAND Flash support + * @references: borrowed heavily from Linux mtd-utils code: + * flash_eraseall.c by Arcom Control System Ltd + * nandwrite.c by Steven J. Hill (sjhill@realitydiluted.com) + * and Thomas Gleixner (tglx@linutronix.de) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) + +#include +#include +#include + +#include +#include + +typedef struct erase_info erase_info_t; +typedef struct mtd_info mtd_info_t; + +/* support only for native endian JFFS2 */ +#define cpu_to_je16(x) (x) +#define cpu_to_je32(x) (x) + +/*****************************************************************************/ +static int nand_block_bad_scrub(struct mtd_info *mtd, loff_t ofs, int getchip) +{ + return 0; +} + +/** + * nand_erase_opts: - erase NAND flash with support for various options + * (jffs2 formating) + * + * @param meminfo NAND device to erase + * @param opts options, @see struct nand_erase_options + * @return 0 in case of success + * + * This code is ported from flash_eraseall.c from Linux mtd utils by + * Arcom Control System Ltd. + */ +int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) +{ + struct jffs2_unknown_node cleanmarker; + int clmpos = 0; + int clmlen = 8; + erase_info_t erase; + ulong erase_length; + int isNAND; + int bbtest = 1; + int result; + int percent_complete = -1; + int (*nand_block_bad_old)(struct mtd_info *, loff_t, int) = NULL; + const char *mtd_device = meminfo->name; + + memset(&erase, 0, sizeof(erase)); + + erase.mtd = meminfo; + erase.len = meminfo->erasesize; + if (opts->offset == 0 && opts->length == 0) { + /* erase complete chip */ + erase.addr = 0; + erase_length = meminfo->size; + } else { + /* erase specified region */ + erase.addr = opts->offset; + erase_length = opts->length; + } + + isNAND = meminfo->type == MTD_NANDFLASH ? 1 : 0; + + if (opts->jffs2) { + cleanmarker.magic = cpu_to_je16 (JFFS2_MAGIC_BITMASK); + cleanmarker.nodetype = cpu_to_je16 (JFFS2_NODETYPE_CLEANMARKER); + if (isNAND) { + struct nand_oobinfo *oobinfo = &meminfo->oobinfo; + + /* check for autoplacement */ + if (oobinfo->useecc == MTD_NANDECC_AUTOPLACE) { + /* get the position of the free bytes */ + if (!oobinfo->oobfree[0][1]) { + printf(" Eeep. Autoplacement selected " + "and no empty space in oob\n"); + return -1; + } + clmpos = oobinfo->oobfree[0][0]; + clmlen = oobinfo->oobfree[0][1]; + if (clmlen > 8) + clmlen = 8; + } else { + /* legacy mode */ + switch (meminfo->oobsize) { + case 8: + clmpos = 6; + clmlen = 2; + break; + case 16: + clmpos = 8; + clmlen = 8; + break; + case 64: + clmpos = 16; + clmlen = 8; + break; + } + } + + cleanmarker.totlen = cpu_to_je32(8); + } else { + cleanmarker.totlen = + cpu_to_je32(sizeof(struct jffs2_unknown_node)); + } + cleanmarker.hdr_crc = cpu_to_je32( + crc32_no_comp(0, (unsigned char *) &cleanmarker, + sizeof(struct jffs2_unknown_node) - 4)); + } + + /* scrub option allows to erase badblock. To prevent internal + * check from erase() method, set block check method to dummy + * and disable bad block table while erasing. + */ + if (opts->scrub) { + struct nand_chip *priv_nand = meminfo->priv; + + nand_block_bad_old = priv_nand->block_bad; + priv_nand->block_bad = nand_block_bad_scrub; + /* we don't need the bad block table anymore... + * after scrub, there are no bad blocks left! + */ + if (priv_nand->bbt) { + kfree(priv_nand->bbt); + } + priv_nand->bbt = NULL; + } + + for (; + erase.addr < opts->offset + erase_length; + erase.addr += meminfo->erasesize) { + + WATCHDOG_RESET (); + + if (!opts->scrub && bbtest) { + int ret = meminfo->block_isbad(meminfo, erase.addr); + if (ret > 0) { + if (!opts->quiet) + printf("\rSkipping bad block at " + "0x%08x " + " \n", + erase.addr); + continue; + + } else if (ret < 0) { + printf("\n%s: MTD get bad block failed: %d\n", + mtd_device, + ret); + return -1; + } + } + + result = meminfo->erase(meminfo, &erase); + if (result != 0) { + printf("\n%s: MTD Erase failure: %d\n", + mtd_device, result); + continue; + } + + /* format for JFFS2 ? */ + if (opts->jffs2) { + + /* write cleanmarker */ + if (isNAND) { + size_t written; + result = meminfo->write_oob(meminfo, + erase.addr + clmpos, + clmlen, + &written, + (unsigned char *) + &cleanmarker); + if (result != 0) { + printf("\n%s: MTD writeoob failure: %d\n", + mtd_device, result); + continue; + } + } else { + printf("\n%s: this erase routine only supports" + " NAND devices!\n", + mtd_device); + } + } + + if (!opts->quiet) { + int percent = (int) + ((unsigned long long) + (erase.addr+meminfo->erasesize-opts->offset) + * 100 / erase_length); + + /* output progress message only at whole percent + * steps to reduce the number of messages printed + * on (slow) serial consoles + */ + if (percent != percent_complete) { + percent_complete = percent; + + printf("\rErasing at 0x%x -- %3d%% complete.", + erase.addr, percent); + + if (opts->jffs2 && result == 0) + printf(" Cleanmarker written at 0x%x.", + erase.addr); + } + } + } + if (!opts->quiet) + printf("\n"); + + if (nand_block_bad_old) { + struct nand_chip *priv_nand = meminfo->priv; + + priv_nand->block_bad = nand_block_bad_old; + priv_nand->scan_bbt(meminfo); + } + + return 0; +} + +#define MAX_PAGE_SIZE 2048 +#define MAX_OOB_SIZE 64 + +/* + * buffer array used for writing data + */ +static unsigned char data_buf[MAX_PAGE_SIZE]; +static unsigned char oob_buf[MAX_OOB_SIZE]; + +/* OOB layouts to pass into the kernel as default */ +static struct nand_oobinfo none_oobinfo = { + .useecc = MTD_NANDECC_OFF, +}; + +static struct nand_oobinfo jffs2_oobinfo = { + .useecc = MTD_NANDECC_PLACE, + .eccbytes = 6, + .eccpos = { 0, 1, 2, 3, 6, 7 } +}; + +static struct nand_oobinfo yaffs_oobinfo = { + .useecc = MTD_NANDECC_PLACE, + .eccbytes = 6, + .eccpos = { 8, 9, 10, 13, 14, 15} +}; + +static struct nand_oobinfo autoplace_oobinfo = { + .useecc = MTD_NANDECC_AUTOPLACE +}; + +/** + * nand_write_opts: - write image to NAND flash with support for various options + * + * @param meminfo NAND device to erase + * @param opts write options (@see nand_write_options) + * @return 0 in case of success + * + * This code is ported from nandwrite.c from Linux mtd utils by + * Steven J. Hill and Thomas Gleixner. + */ +int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts) +{ + int imglen = 0; + int pagelen; + int baderaseblock; + int blockstart = -1; + loff_t offs; + int readlen; + int oobinfochanged = 0; + int percent_complete = -1; + struct nand_oobinfo old_oobinfo; + ulong mtdoffset = opts->offset; + ulong erasesize_blockalign; + u_char *buffer = opts->buffer; + size_t written; + int result; + + if (opts->pad && opts->writeoob) { + printf("Can't pad when oob data is present.\n"); + return -1; + } + + /* set erasesize to specified number of blocks - to match + * jffs2 (virtual) block size */ + if (opts->blockalign == 0) { + erasesize_blockalign = meminfo->erasesize; + } else { + erasesize_blockalign = meminfo->erasesize * opts->blockalign; + } + + /* make sure device page sizes are valid */ + if (!(meminfo->oobsize == 16 && meminfo->oobblock == 512) + && !(meminfo->oobsize == 8 && meminfo->oobblock == 256) + && !(meminfo->oobsize == 64 && meminfo->oobblock == 2048)) { + printf("Unknown flash (not normal NAND)\n"); + return -1; + } + + /* read the current oob info */ + memcpy(&old_oobinfo, &meminfo->oobinfo, sizeof(old_oobinfo)); + + /* write without ecc? */ + if (opts->noecc) { + memcpy(&meminfo->oobinfo, &none_oobinfo, + sizeof(meminfo->oobinfo)); + oobinfochanged = 1; + } + + /* autoplace ECC? */ + if (opts->autoplace && (old_oobinfo.useecc != MTD_NANDECC_AUTOPLACE)) { + + memcpy(&meminfo->oobinfo, &autoplace_oobinfo, + sizeof(meminfo->oobinfo)); + oobinfochanged = 1; + } + + /* force OOB layout for jffs2 or yaffs? */ + if (opts->forcejffs2 || opts->forceyaffs) { + struct nand_oobinfo *oobsel = + opts->forcejffs2 ? &jffs2_oobinfo : &yaffs_oobinfo; + + if (meminfo->oobsize == 8) { + if (opts->forceyaffs) { + printf("YAFSS cannot operate on " + "256 Byte page size\n"); + goto restoreoob; + } + /* Adjust number of ecc bytes */ + jffs2_oobinfo.eccbytes = 3; + } + + memcpy(&meminfo->oobinfo, oobsel, sizeof(meminfo->oobinfo)); + } + + /* get image length */ + imglen = opts->length; + pagelen = meminfo->oobblock + + ((opts->writeoob != 0) ? meminfo->oobsize : 0); + + /* check, if file is pagealigned */ + if ((!opts->pad) && ((imglen % pagelen) != 0)) { + printf("Input block length is not page aligned\n"); + goto restoreoob; + } + + /* check, if length fits into device */ + if (((imglen / pagelen) * meminfo->oobblock) + > (meminfo->size - opts->offset)) { + printf("Image %d bytes, NAND page %d bytes, " + "OOB area %u bytes, device size %u bytes\n", + imglen, pagelen, meminfo->oobblock, meminfo->size); + printf("Input block does not fit into device\n"); + goto restoreoob; + } + + if (!opts->quiet) + printf("\n"); + + /* get data from input and write to the device */ + while (imglen && (mtdoffset < meminfo->size)) { + + WATCHDOG_RESET (); + + /* + * new eraseblock, check for bad block(s). Stay in the + * loop to be sure if the offset changes because of + * a bad block, that the next block that will be + * written to is also checked. Thus avoiding errors if + * the block(s) after the skipped block(s) is also bad + * (number of blocks depending on the blockalign + */ + while (blockstart != (mtdoffset & (~erasesize_blockalign+1))) { + blockstart = mtdoffset & (~erasesize_blockalign+1); + offs = blockstart; + baderaseblock = 0; + + /* check all the blocks in an erase block for + * bad blocks */ + do { + int ret = meminfo->block_isbad(meminfo, offs); + + if (ret < 0) { + printf("Bad block check failed\n"); + goto restoreoob; + } + if (ret == 1) { + baderaseblock = 1; + if (!opts->quiet) + printf("\rBad block at 0x%lx " + "in erase block from " + "0x%x will be skipped\n", + (long) offs, + blockstart); + } + + if (baderaseblock) { + mtdoffset = blockstart + + erasesize_blockalign; + } + offs += erasesize_blockalign + / opts->blockalign; + } while (offs < blockstart + erasesize_blockalign); + } + + readlen = meminfo->oobblock; + if (opts->pad && (imglen < readlen)) { + readlen = imglen; + memset(data_buf + readlen, 0xff, + meminfo->oobblock - readlen); + } + + /* read page data from input memory buffer */ + memcpy(data_buf, buffer, readlen); + buffer += readlen; + + if (opts->writeoob) { + /* read OOB data from input memory block, exit + * on failure */ + memcpy(oob_buf, buffer, meminfo->oobsize); + buffer += meminfo->oobsize; + + /* write OOB data first, as ecc will be placed + * in there*/ + result = meminfo->write_oob(meminfo, + mtdoffset, + meminfo->oobsize, + &written, + (unsigned char *) + &oob_buf); + + if (result != 0) { + printf("\nMTD writeoob failure: %d\n", + result); + goto restoreoob; + } + imglen -= meminfo->oobsize; + } + + /* write out the page data */ + result = meminfo->write(meminfo, + mtdoffset, + meminfo->oobblock, + &written, + (unsigned char *) &data_buf); + + if (result != 0) { + printf("writing NAND page at offset 0x%lx failed\n", + mtdoffset); + goto restoreoob; + } + imglen -= readlen; + + if (!opts->quiet) { + int percent = (int) + ((unsigned long long) + (opts->length-imglen) * 100 + / opts->length); + /* output progress message only at whole percent + * steps to reduce the number of messages printed + * on (slow) serial consoles + */ + if (percent != percent_complete) { + printf("\rWriting data at 0x%x " + "-- %3d%% complete.", + mtdoffset, percent); + percent_complete = percent; + } + } + + mtdoffset += meminfo->oobblock; + } + + if (!opts->quiet) + printf("\n"); + +restoreoob: + if (oobinfochanged) { + memcpy(&meminfo->oobinfo, &old_oobinfo, + sizeof(meminfo->oobinfo)); + } + + if (imglen > 0) { + printf("Data did not fit into device, due to bad blocks\n"); + return -1; + } + + /* return happy */ + return 0; +} + +/** + * nand_read_opts: - read image from NAND flash with support for various options + * + * @param meminfo NAND device to erase + * @param opts read options (@see struct nand_read_options) + * @return 0 in case of success + * + */ +int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts) +{ + int imglen = opts->length; + int pagelen; + int baderaseblock; + int blockstart = -1; + int percent_complete = -1; + loff_t offs; + size_t readlen; + ulong mtdoffset = opts->offset; + u_char *buffer = opts->buffer; + int result; + + /* make sure device page sizes are valid */ + if (!(meminfo->oobsize == 16 && meminfo->oobblock == 512) + && !(meminfo->oobsize == 8 && meminfo->oobblock == 256) + && !(meminfo->oobsize == 64 && meminfo->oobblock == 2048)) { + printf("Unknown flash (not normal NAND)\n"); + return -1; + } + + pagelen = meminfo->oobblock + + ((opts->readoob != 0) ? meminfo->oobsize : 0); + + /* check, if length is not larger than device */ + if (((imglen / pagelen) * meminfo->oobblock) + > (meminfo->size - opts->offset)) { + printf("Image %d bytes, NAND page %d bytes, " + "OOB area %u bytes, device size %u bytes\n", + imglen, pagelen, meminfo->oobblock, meminfo->size); + printf("Input block is larger than device\n"); + return -1; + } + + if (!opts->quiet) + printf("\n"); + + /* get data from input and write to the device */ + while (imglen && (mtdoffset < meminfo->size)) { + + WATCHDOG_RESET (); + + /* + * new eraseblock, check for bad block(s). Stay in the + * loop to be sure if the offset changes because of + * a bad block, that the next block that will be + * written to is also checked. Thus avoiding errors if + * the block(s) after the skipped block(s) is also bad + * (number of blocks depending on the blockalign + */ + while (blockstart != (mtdoffset & (~meminfo->erasesize+1))) { + blockstart = mtdoffset & (~meminfo->erasesize+1); + offs = blockstart; + baderaseblock = 0; + + /* check all the blocks in an erase block for + * bad blocks */ + do { + int ret = meminfo->block_isbad(meminfo, offs); + + if (ret < 0) { + printf("Bad block check failed\n"); + return -1; + } + if (ret == 1) { + baderaseblock = 1; + if (!opts->quiet) + printf("\rBad block at 0x%lx " + "in erase block from " + "0x%x will be skipped\n", + (long) offs, + blockstart); + } + + if (baderaseblock) { + mtdoffset = blockstart + + meminfo->erasesize; + } + offs += meminfo->erasesize; + + } while (offs < blockstart + meminfo->erasesize); + } + + + /* read page data to memory buffer */ + result = meminfo->read(meminfo, + mtdoffset, + meminfo->oobblock, + &readlen, + (unsigned char *) &data_buf); + + if (result != 0) { + printf("reading NAND page at offset 0x%lx failed\n", + mtdoffset); + return -1; + } + + if (imglen < readlen) { + readlen = imglen; + } + + memcpy(buffer, data_buf, readlen); + buffer += readlen; + imglen -= readlen; + + if (opts->readoob) { + result = meminfo->read_oob(meminfo, + mtdoffset, + meminfo->oobsize, + &readlen, + (unsigned char *) + &oob_buf); + + if (result != 0) { + printf("\nMTD readoob failure: %d\n", + result); + return -1; + } + + + if (imglen < readlen) { + readlen = imglen; + } + + memcpy(buffer, oob_buf, readlen); + + buffer += readlen; + imglen -= readlen; + } + + if (!opts->quiet) { + int percent = (int) + ((unsigned long long) + (opts->length-imglen) * 100 + / opts->length); + /* output progress message only at whole percent + * steps to reduce the number of messages printed + * on (slow) serial consoles + */ + if (percent != percent_complete) { + if (!opts->quiet) + printf("\rReading data from 0x%x " + "-- %3d%% complete.", + mtdoffset, percent); + percent_complete = percent; + } + } + + mtdoffset += meminfo->oobblock; + } + + if (!opts->quiet) + printf("\n"); + + if (imglen > 0) { + printf("Could not read entire image due to bad blocks\n"); + return -1; + } + + /* return happy */ + return 0; +} + +/****************************************************************************** + * Support for locking / unlocking operations of some NAND devices + *****************************************************************************/ + +#define NAND_CMD_LOCK 0x2a +#define NAND_CMD_LOCK_TIGHT 0x2c +#define NAND_CMD_UNLOCK1 0x23 +#define NAND_CMD_UNLOCK2 0x24 +#define NAND_CMD_LOCK_STATUS 0x7a + +/** + * nand_lock: Set all pages of NAND flash chip to the LOCK or LOCK-TIGHT + * state + * + * @param meminfo nand mtd instance + * @param tight bring device in lock tight mode + * + * @return 0 on success, -1 in case of error + * + * The lock / lock-tight command only applies to the whole chip. To get some + * parts of the chip lock and others unlocked use the following sequence: + * + * - Lock all pages of the chip using nand_lock(mtd, 0) (or the lockpre pin) + * - Call nand_unlock() once for each consecutive area to be unlocked + * - If desired: Bring the chip to the lock-tight state using nand_lock(mtd, 1) + * + * If the device is in lock-tight state software can't change the + * current active lock/unlock state of all pages. nand_lock() / nand_unlock() + * calls will fail. It is only posible to leave lock-tight state by + * an hardware signal (low pulse on _WP pin) or by power down. + */ +int nand_lock(nand_info_t *meminfo, int tight) +{ + int ret = 0; + int status; + struct nand_chip *this = meminfo->priv; + + /* select the NAND device */ + this->select_chip(meminfo, 0); + + this->cmdfunc(meminfo, + (tight ? NAND_CMD_LOCK_TIGHT : NAND_CMD_LOCK), + -1, -1); + + /* call wait ready function */ + status = this->waitfunc(meminfo, this, FL_WRITING); + + /* see if device thinks it succeeded */ + if (status & 0x01) { + ret = -1; + } + + /* de-select the NAND device */ + this->select_chip(meminfo, -1); + return ret; +} + +/** + * nand_get_lock_status: - query current lock state from one page of NAND + * flash + * + * @param meminfo nand mtd instance + * @param offset page address to query (muss be page aligned!) + * + * @return -1 in case of error + * >0 lock status: + * bitfield with the following combinations: + * NAND_LOCK_STATUS_TIGHT: page in tight state + * NAND_LOCK_STATUS_LOCK: page locked + * NAND_LOCK_STATUS_UNLOCK: page unlocked + * + */ +int nand_get_lock_status(nand_info_t *meminfo, ulong offset) +{ + int ret = 0; + int chipnr; + int page; + struct nand_chip *this = meminfo->priv; + + /* select the NAND device */ + chipnr = (int)(offset >> this->chip_shift); + this->select_chip(meminfo, chipnr); + + + if ((offset & (meminfo->oobblock - 1)) != 0) { + printf ("nand_get_lock_status: " + "Start address must be beginning of " + "nand page!\n"); + ret = -1; + goto out; + } + + /* check the Lock Status */ + page = (int)(offset >> this->page_shift); + this->cmdfunc(meminfo, NAND_CMD_LOCK_STATUS, -1, page & this->pagemask); + + ret = this->read_byte(meminfo) & (NAND_LOCK_STATUS_TIGHT + | NAND_LOCK_STATUS_LOCK + | NAND_LOCK_STATUS_UNLOCK); + + out: + /* de-select the NAND device */ + this->select_chip(meminfo, -1); + return ret; +} + +/** + * nand_unlock: - Unlock area of NAND pages + * only one consecutive area can be unlocked at one time! + * + * @param meminfo nand mtd instance + * @param start start byte address + * @param length number of bytes to unlock (must be a multiple of + * page size nand->oobblock) + * + * @return 0 on success, -1 in case of error + */ +int nand_unlock(nand_info_t *meminfo, ulong start, ulong length) +{ + int ret = 0; + int chipnr; + int status; + int page; + struct nand_chip *this = meminfo->priv; + printf ("nand_unlock: start: %08x, length: %d!\n", + (int)start, (int)length); + + /* select the NAND device */ + chipnr = (int)(start >> this->chip_shift); + this->select_chip(meminfo, chipnr); + + /* check the WP bit */ + this->cmdfunc(meminfo, NAND_CMD_STATUS, -1, -1); + if ((this->read_byte(meminfo) & 0x80) == 0) { + printf ("nand_unlock: Device is write protected!\n"); + ret = -1; + goto out; + } + + if ((start & (meminfo->oobblock - 1)) != 0) { + printf ("nand_unlock: Start address must be beginning of " + "nand page!\n"); + ret = -1; + goto out; + } + + if (length == 0 || (length & (meminfo->oobblock - 1)) != 0) { + printf ("nand_unlock: Length must be a multiple of nand page " + "size!\n"); + ret = -1; + goto out; + } + + /* submit address of first page to unlock */ + page = (int)(start >> this->page_shift); + this->cmdfunc(meminfo, NAND_CMD_UNLOCK1, -1, page & this->pagemask); + + /* submit ADDRESS of LAST page to unlock */ + page += (int)(length >> this->page_shift) - 1; + this->cmdfunc(meminfo, NAND_CMD_UNLOCK2, -1, page & this->pagemask); + + /* call wait ready function */ + status = this->waitfunc(meminfo, this, FL_WRITING); + /* see if device thinks it succeeded */ + if (status & 0x01) { + /* there was an error */ + ret = -1; + goto out; + } + + out: + /* de-select the NAND device */ + this->select_chip(meminfo, -1); + return ret; +} + +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) */ diff --git a/include/nand.h b/include/nand.h index 905115b3dac..5c7311fd505 100644 --- a/include/nand.h +++ b/include/nand.h @@ -60,4 +60,61 @@ static inline int nand_erase(nand_info_t *info, ulong off, ulong size) return info->erase(info, &instr); } + +/***************************************************************************** + * declarations from nand_util.c + ****************************************************************************/ + +struct nand_write_options { + u_char *buffer; /* memory block containing image to write */ + ulong length; /* number of bytes to write */ + ulong offset; /* start address in NAND */ + int quiet; /* don't display progress messages */ + int autoplace; /* if true use auto oob layout */ + int forcejffs2; /* force jffs2 oob layout */ + int forceyaffs; /* force yaffs oob layout */ + int noecc; /* write without ecc */ + int writeoob; /* image contains oob data */ + int pad; /* pad to page size */ + int blockalign; /* 1|2|4 set multiple of eraseblocks + * to align to */ +}; + +typedef struct nand_write_options nand_write_options_t; + +struct nand_read_options { + u_char *buffer; /* memory block in which read image is written*/ + ulong length; /* number of bytes to read */ + ulong offset; /* start address in NAND */ + int quiet; /* don't display progress messages */ + int readoob; /* put oob data in image */ +}; + +typedef struct nand_read_options nand_read_options_t; + +struct nand_erase_options { + ulong length; /* number of bytes to erase */ + ulong offset; /* first address in NAND to erase */ + int quiet; /* don't display progress messages */ + int jffs2; /* if true: format for jffs2 usage + * (write appropriate cleanmarker blocks) */ + int scrub; /* if true, really clean NAND by erasing + * bad blocks (UNSAFE) */ +}; + +typedef struct nand_erase_options nand_erase_options_t; + +int nand_write_opts(nand_info_t *meminfo, const nand_write_options_t *opts); + +int nand_read_opts(nand_info_t *meminfo, const nand_read_options_t *opts); +int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts); + +#define NAND_LOCK_STATUS_TIGHT 0x01 +#define NAND_LOCK_STATUS_LOCK 0x02 +#define NAND_LOCK_STATUS_UNLOCK 0x04 + +int nand_lock( nand_info_t *meminfo, int tight ); +int nand_unlock( nand_info_t *meminfo, ulong start, ulong length ); +int nand_get_lock_status(nand_info_t *meminfo, ulong offset); + #endif diff --git a/lib_generic/crc32.c b/lib_generic/crc32.c index 50ca4ffd380..82834135022 100644 --- a/lib_generic/crc32.c +++ b/lib_generic/crc32.c @@ -171,7 +171,9 @@ uLong ZEXPORT crc32(crc, buf, len) return crc ^ 0xffffffffL; } -#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) \ + || (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY) + /* No ones complement version. JFFS2 (and other things ?) * don't use ones compliment in their CRC calculations. -- cgit v1.3.1 From e10390ddd736b0dad1528eec4b0fe35c0827139a Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Tue, 10 Oct 2006 17:06:53 -0500 Subject: Fix whitespace issues. --- doc/README.mpc8641hpcn | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'doc') diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn index 8ea0b1e9eeb..4a650ce43c2 100644 --- a/doc/README.mpc8641hpcn +++ b/doc/README.mpc8641hpcn @@ -30,7 +30,7 @@ Switches: SW1(6-8) = 001 CFG_SYSCLK = 000 :: SYSCLK = 33MHz 001 :: SYSCLK = 40MHz - SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X + SW2(1-4) = 1100 CFG_CCBPLL = 0010 :: 2X 0100 :: 4X 0110 :: 6X 1000 :: 8X @@ -109,7 +109,7 @@ To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF): 4. Memory Map ------------- - Memory Range Device Size + Memory Range Device Size ------------ ------ ---- 0x0000_0000 0x7fff_ffff DDR 2G 0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M -- cgit v1.3.1 From fcfed4f2f234836a0b308fd0a782f4625cd40bad Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 18 Oct 2006 22:44:38 +0200 Subject: Coding Style cleanup. --- board/v38b/ethaddr.c | 4 +- board/v38b/v38b.c | 1 - doc/README.nand | 3 -- include/configs/V38B.h | 112 ++++++++++++++++++++++++------------------------- 4 files changed, 58 insertions(+), 62 deletions(-) (limited to 'doc') diff --git a/board/v38b/ethaddr.c b/board/v38b/ethaddr.c index 105608051c7..aaa629ef611 100644 --- a/board/v38b/ethaddr.c +++ b/board/v38b/ethaddr.c @@ -118,7 +118,7 @@ void read_2501_memory(unsigned char *psernum, unsigned char *perr) crcval = 0; for (i=0; i> 1) | 0x80; else rdat = rdat >> 1; - + udelay(60); /* at least 60 us */ } /* copy the return value */ diff --git a/board/v38b/v38b.c b/board/v38b/v38b.c index c56c6c84d27..99fe7dbc3c4 100644 --- a/board/v38b/v38b.c +++ b/board/v38b/v38b.c @@ -250,4 +250,3 @@ void hw_watchdog_reset(void) { /* TODO fill this in */ } - diff --git a/doc/README.nand b/doc/README.nand index 2b9a52966c5..5279a4f2bc5 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -1,9 +1,7 @@ NAND FLASH commands and notes - See NOTE below!!! - # (C) Copyright 2003 # Dave Ellis, SIXNET, dge@sixnetio.com # @@ -209,7 +207,6 @@ the tree until the DoC is ported to use the new NAND support (or boards with DoC will break). - Additional improvements to the NAND subsystem by Guido Classen, 10-10-2006 JFFS2 related commands: diff --git a/include/configs/V38B.h b/include/configs/V38B.h index 9b8fc699a90..8eea504742a 100644 --- a/include/configs/V38B.h +++ b/include/configs/V38B.h @@ -11,7 +11,7 @@ * * This program is distributed in the hope that it will be useful, but WITHOUT * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or - * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License * for more details. * * You should have received a copy of the GNU General Public License along @@ -35,35 +35,35 @@ * (easy to change) */ -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_V38B 1 /* ... on V38B board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ +#define CONFIG_V38B 1 /* ... on V38B board */ +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ -#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ -#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ -#define CONFIG_HW_WATCHDOG 1 /* has watchdog */ +#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */ +#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */ +#define CONFIG_HW_WATCHDOG 1 /* has watchdog */ #define CONFIG_NETCONSOLE 1 -#define CONFIG_BOARD_EARLY_INIT_R 1 /* make flash read/write */ +#define CONFIG_BOARD_EARLY_INIT_R 1 /* make flash read/write */ -#define CFG_XLB_PIPELINING 1 /* gives better performance */ +#define CFG_XLB_PIPELINING 1 /* gives better performance */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* * Serial console configuration */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } @@ -97,12 +97,12 @@ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ /* * Supported commands */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ CFG_CMD_FAT | \ CFG_CMD_I2C | \ CFG_CMD_IDE | \ @@ -112,7 +112,7 @@ CFG_CMD_IRQ | \ CFG_CMD_JFFS2 | \ CFG_CMD_MII | \ - CFG_CMD_SDRAMi | \ + CFG_CMD_SDRAMi | \ CFG_CMD_DATE | \ CFG_CMD_USB | \ CFG_CMD_FAT) @@ -123,7 +123,7 @@ /* * Boot low with 16 MB Flash */ -# define CFG_LOWBOOT 1 +# define CFG_LOWBOOT 1 # define CFG_LOWBOOT16 1 /* @@ -131,35 +131,35 @@ */ #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#define CONFIG_PREBOOT "echo;" \ +#define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ "echo" #undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "devno=5\0" \ - "hostname=V38B_$(devno)\0" \ - "ipaddr=10.100.99.$(devno)\0" \ - "netmask=255.255.0.0\0" \ - "serverip=10.100.10.90\0" \ - "gatewayip=10.100.254.254\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "bootfile=mpc5200/uImage\0" \ - "bootcmd=run net_nfs\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):" \ - "$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip;bootm $(kernel_addr) " \ - "$(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs " \ - "addip;bootm\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "devno=5\0" \ + "hostname=V38B_$(devno)\0" \ + "ipaddr=10.100.99.$(devno)\0" \ + "netmask=255.255.0.0\0" \ + "serverip=10.100.10.90\0" \ + "gatewayip=10.100.254.254\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=mpc5200/uImage\0" \ + "bootcmd=run net_nfs\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):" \ + "$(netmask):$(hostname):$(netdev):off panic=1\0" \ + "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;bootm $(kernel_addr) " \ + "$(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs " \ + "addip;bootm\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "" #define CONFIG_BOOTCOMMAND "run net_nfs" @@ -196,13 +196,13 @@ */ #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ #define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_CFI_AMD_RESET 1 +#define CFG_FLASH_CFI_AMD_RESET 1 #define CFG_FLASH_BASE 0xFF000000 #define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #define CFG_FLASH_SIZE 0x01000000 /* 16 MiB */ #define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */ /* * Environment settings @@ -243,7 +243,7 @@ */ #define CONFIG_MPC5xxx_FEC 1 #define CONFIG_PHY_ADDR 0x00 -#define CONFIG_MII 1 +#define CONFIG_MII 1 /* * GPIO configuration @@ -307,12 +307,12 @@ *----------------------------------------------------------------------- */ -#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */ +#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ -#define CONFIG_IDE_RESET /* reset for ide supported */ +#define CONFIG_IDE_RESET /* reset for ide supported */ #define CONFIG_IDE_PREINIT #define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ @@ -331,13 +331,13 @@ /* Offset for alternate registers */ #define CFG_ATA_ALT_OFFSET (0x005C) -/* Interval between registers */ -#define CFG_ATA_STRIDE 4 +/* Interval between registers */ +#define CFG_ATA_STRIDE 4 -/* Status LED */ +/* Status LED */ -#define CONFIG_STATUS_LED /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ +#define CONFIG_STATUS_LED /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ #define CFG_LED_BASE (0xf0000600 + 0x70) /* Timer 7 GPIO */ -- cgit v1.3.1 From 7b64fef33c66be648826c0ff9758298ef13d0604 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Tue, 24 Oct 2006 14:21:16 +0200 Subject: Add AVR32 architecture support Patch by Haavard Skinnemoen, 6 Sep 2006 16:23:02 +0200 This patch adds common infrastructure code for the Atmel AVR32 architecture. See doc/README.AVR32 for details. Signed-off-by: Haavard Skinnemoen --- MAINTAINERS | 7 + Makefile | 7 + README | 5 +- avr32_config.mk | 25 ++++ doc/README.AVR32 | 33 +++++ examples/Makefile | 4 + examples/stubs.c | 13 ++ include/asm-avr32/addrspace.h | 46 ++++++ include/asm-avr32/bitops.h | 25 ++++ include/asm-avr32/byteorder.h | 37 +++++ include/asm-avr32/cacheflush.h | 83 +++++++++++ include/asm-avr32/div64.h | 39 +++++ include/asm-avr32/dma-mapping.h | 64 ++++++++ include/asm-avr32/errno.h | 132 +++++++++++++++++ include/asm-avr32/global_data.h | 59 ++++++++ include/asm-avr32/initcalls.h | 33 +++++ include/asm-avr32/io.h | 92 ++++++++++++ include/asm-avr32/posix_types.h | 144 ++++++++++++++++++ include/asm-avr32/processor.h | 97 +++++++++++++ include/asm-avr32/ptrace.h | 148 +++++++++++++++++++ include/asm-avr32/sdram.h | 33 +++++ include/asm-avr32/sections.h | 39 +++++ include/asm-avr32/setup.h | 142 ++++++++++++++++++ include/asm-avr32/string.h | 28 ++++ include/asm-avr32/sysreg.h | 279 +++++++++++++++++++++++++++++++++++ include/asm-avr32/types.h | 84 +++++++++++ include/asm-avr32/u-boot.h | 56 +++++++ lib_avr32/Makefile | 47 ++++++ lib_avr32/avr32_linux.c | 315 ++++++++++++++++++++++++++++++++++++++++ lib_avr32/board.c | 175 ++++++++++++++++++++++ lib_avr32/div64.c | 54 +++++++ lib_avr32/interrupts.c | 39 +++++ lib_avr32/memset.S | 81 +++++++++++ 33 files changed, 2463 insertions(+), 2 deletions(-) create mode 100644 avr32_config.mk create mode 100644 doc/README.AVR32 create mode 100644 include/asm-avr32/addrspace.h create mode 100644 include/asm-avr32/bitops.h create mode 100644 include/asm-avr32/byteorder.h create mode 100644 include/asm-avr32/cacheflush.h create mode 100644 include/asm-avr32/div64.h create mode 100644 include/asm-avr32/dma-mapping.h create mode 100644 include/asm-avr32/errno.h create mode 100644 include/asm-avr32/global_data.h create mode 100644 include/asm-avr32/initcalls.h create mode 100644 include/asm-avr32/io.h create mode 100644 include/asm-avr32/posix_types.h create mode 100644 include/asm-avr32/processor.h create mode 100644 include/asm-avr32/ptrace.h create mode 100644 include/asm-avr32/sdram.h create mode 100644 include/asm-avr32/sections.h create mode 100644 include/asm-avr32/setup.h create mode 100644 include/asm-avr32/string.h create mode 100644 include/asm-avr32/sysreg.h create mode 100644 include/asm-avr32/types.h create mode 100644 include/asm-avr32/u-boot.h create mode 100644 lib_avr32/Makefile create mode 100644 lib_avr32/avr32_linux.c create mode 100644 lib_avr32/board.c create mode 100644 lib_avr32/div64.c create mode 100644 lib_avr32/interrupts.c create mode 100644 lib_avr32/memset.S (limited to 'doc') diff --git a/MAINTAINERS b/MAINTAINERS index 42627196f86..d7ef203e551 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -554,6 +554,13 @@ Zachary P. Landau r5200 mcf52x2 +######################################################################### +# AVR32 Systems: # +# # +# Maintainer Name, Email Address # +# Board CPU # +######################################################################### + ######################################################################### # End of MAINTAINERS list # ######################################################################### diff --git a/Makefile b/Makefile index 92034947962..5260a612ff3 100644 --- a/Makefile +++ b/Makefile @@ -152,6 +152,9 @@ endif ifeq ($(ARCH),blackfin) CROSS_COMPILE = bfin-elf- endif +ifeq ($(ARCH),avr32) +CROSS_COMPILE = avr32- +endif endif endif @@ -2099,6 +2102,10 @@ pb1000_config : unconfig @echo "#define CONFIG_PB1000 1" >>$(obj)include/config.h @$(MKCONFIG) -a pb1x00 mips mips pb1x00 +#======================================================================== +# AVR32 +#======================================================================== + ######################################################################### ## MIPS64 5Kc ######################################################################### diff --git a/README b/README index a0949f0d9b1..8405a9b0cd1 100644 --- a/README +++ b/README @@ -156,6 +156,7 @@ Directory Hierarchy: - examples Example code for standalone applications, etc. - include Header Files - lib_arm Files generic to ARM architecture +- lib_avr32 Files generic to AVR32 architecture - lib_generic Files generic to all architectures - lib_i386 Files generic to i386 architecture - lib_m68k Files generic to m68k architecture @@ -2722,9 +2723,9 @@ defines the following image properties: 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks, LynxOS, pSOS, QNX, RTEMS, ARTOS; Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS). -* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86, +* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86, IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit; - Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC). + Currently supported: ARM, AVR32, Intel x86, MIPS, NIOS, PowerPC). * Compression Type (uncompressed, gzip, bzip2) * Load Address * Entry Point diff --git a/avr32_config.mk b/avr32_config.mk new file mode 100644 index 00000000000..0b92053e1af --- /dev/null +++ b/avr32_config.mk @@ -0,0 +1,25 @@ +# +# (C) Copyright 2000-2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +PLATFORM_RELFLAGS += -ffixed-r5 -mno-pic -mrelax +PLATFORM_LDFLAGS += --relax diff --git a/doc/README.AVR32 b/doc/README.AVR32 new file mode 100644 index 00000000000..abec872c57a --- /dev/null +++ b/doc/README.AVR32 @@ -0,0 +1,33 @@ +From: Haavard Skinnemoen +Date: Wed, 30 Aug 2006 17:01:46 +0200 +Subject: [PATCH] AVR32 architecture support + +This patch adds common infrastructure code for the Atmel AVR32 +architecture. + +AVR32 is a new high-performance 32-bit RISC microprocessor core, +designed for cost-sensitive embedded applications, with particular +emphasis on low power consumption and high code density. The AVR32 +architecture is not binary compatible with earlier 8-bit AVR +architectures. + +The AVR32 architecture, including the instruction set, is described +by the AVR32 Architecture Manual, available from + +http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf + +A GNU toolchain with support for AVR32 is included with the ATSTK1000 +BSP, which can be downloaded as an ISO image from + +http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918 + +Alternatively, you can build it yourself by following the +Getting Started guide at avr32linux.org, which also provides links +to the necessary sources and patches you need to download: + +http://avr32linux.org/twiki/bin/view/Main/GettingStarted + +The AVR32 ports of u-boot, the Linux kernel, the GNU toolchain and +other associated software are actively supported by Atmel Corporation. + +Signed-off-by: Haavard Skinnemoen diff --git a/examples/Makefile b/examples/Makefile index 680fe75d921..423a79b2dd5 100644 --- a/examples/Makefile +++ b/examples/Makefile @@ -57,6 +57,10 @@ ifeq ($(ARCH),blackfin) LOAD_ADDR = 0x1000 endif +ifeq ($(ARCH),avr32) +LOAD_ADDR = 0x00000000 +endif + include $(TOPDIR)/config.mk ELF = hello_world diff --git a/examples/stubs.c b/examples/stubs.c index 1caa5757479..ffd314e6b35 100644 --- a/examples/stubs.c +++ b/examples/stubs.c @@ -138,6 +138,19 @@ gd_t *global_data; " P0 = [P0 + %1]\n" \ " JUMP (P0)\n" \ : : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "P0"); +#elif defined(CONFIG_AVR32) +/* + * r6 holds the pointer to the global_data. r8 is call clobbered. + */ +#define EXPORT_FUNC(x) \ + asm volatile( \ + " .globl\t" #x "\n" \ + #x ":\n" \ + " ld.w r8, r6[%0]\n" \ + " ld.w pc, r8[%1]\n" \ + : \ + : "i"(offsetof(gd_t, jt)), "i"(XF_ ##x) \ + : "r8"); #else #error stubs definition missing for this architecture #endif diff --git a/include/asm-avr32/addrspace.h b/include/asm-avr32/addrspace.h new file mode 100644 index 00000000000..b2ba1ee2fef --- /dev/null +++ b/include/asm-avr32/addrspace.h @@ -0,0 +1,46 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_ADDRSPACE_H +#define __ASM_AVR32_ADDRSPACE_H + +/* Memory segments when segmentation is enabled */ +#define P0SEG 0x00000000 +#define P1SEG 0x80000000 +#define P2SEG 0xa0000000 +#define P3SEG 0xc0000000 +#define P4SEG 0xe0000000 + +/* Returns the privileged segment base of a given address */ +#define PXSEG(a) (((unsigned long)(a)) & 0xe0000000) + +/* Returns the physical address of a PnSEG (n=1,2) address */ +#define PHYSADDR(a) (((unsigned long)(a)) & 0x1fffffff) + +/* + * Map an address to a certain privileged segment + */ +#define P1SEGADDR(a) ((__typeof__(a))(((unsigned long)(a) & 0x1fffffff) | P1SEG)) +#define P2SEGADDR(a) ((__typeof__(a))(((unsigned long)(a) & 0x1fffffff) | P2SEG)) +#define P3SEGADDR(a) ((__typeof__(a))(((unsigned long)(a) & 0x1fffffff) | P3SEG)) +#define P4SEGADDR(a) ((__typeof__(a))(((unsigned long)(a) & 0x1fffffff) | P4SEG)) + +#endif /* __ASM_AVR32_ADDRSPACE_H */ diff --git a/include/asm-avr32/bitops.h b/include/asm-avr32/bitops.h new file mode 100644 index 00000000000..f15fd4647e2 --- /dev/null +++ b/include/asm-avr32/bitops.h @@ -0,0 +1,25 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_BITOPS_H +#define __ASM_AVR32_BITOPS_H + +#endif /* __ASM_AVR32_BITOPS_H */ diff --git a/include/asm-avr32/byteorder.h b/include/asm-avr32/byteorder.h new file mode 100644 index 00000000000..2fe867e9786 --- /dev/null +++ b/include/asm-avr32/byteorder.h @@ -0,0 +1,37 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_BYTEORDER_H +#define __ASM_AVR32_BYTEORDER_H + +#include + +#define __arch__swab32(x) __builtin_bswap_32(x) +#define __arch__swab16(x) __builtin_bswap_16(x) + +#if !defined(__STRICT_ANSI__) || defined(__KERNEL__) +# define __BYTEORDER_HAS_U64__ +# define __SWAB_64_THRU_32__ +#endif + +#include + +#endif /* __ASM_AVR32_BYTEORDER_H */ diff --git a/include/asm-avr32/cacheflush.h b/include/asm-avr32/cacheflush.h new file mode 100644 index 00000000000..929f68e1a0a --- /dev/null +++ b/include/asm-avr32/cacheflush.h @@ -0,0 +1,83 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_CACHEFLUSH_H +#define __ASM_AVR32_CACHEFLUSH_H + +/* + * Invalidate any cacheline containing virtual address vaddr without + * writing anything back to memory. + * + * Note that this function may corrupt unrelated data structures when + * applied on buffers that are not cacheline aligned in both ends. + */ +static inline void dcache_invalidate_line(volatile void *vaddr) +{ + asm volatile("cache %0[0], 0x0b" : : "r"(vaddr) : "memory"); +} + +/* + * Make sure any cacheline containing virtual address vaddr is written + * to memory. + */ +static inline void dcache_clean_line(volatile void *vaddr) +{ + asm volatile("cache %0[0], 0x0c" : : "r"(vaddr) : "memory"); +} + +/* + * Make sure any cacheline containing virtual address vaddr is written + * to memory and then invalidate it. + */ +static inline void dcache_flush_line(volatile void *vaddr) +{ + asm volatile("cache %0[0], 0x0d" : : "r"(vaddr) : "memory"); +} + +/* + * Invalidate any instruction cacheline containing virtual address + * vaddr. + */ +static inline void icache_invalidate_line(volatile void *vaddr) +{ + asm volatile("cache %0[0], 0x01" : : "r"(vaddr) : "memory"); +} + +/* + * Applies the above functions on all lines that are touched by the + * specified virtual address range. + */ +void dcache_invalidate_range(volatile void *start, size_t len); +void dcache_clean_range(volatile void *start, size_t len); +void dcache_flush_range(volatile void *start, size_t len); +void icache_invalidate_range(volatile void *start, size_t len); + +static inline void dcache_flush_unlocked(void) +{ + asm volatile("cache %0[5], 0x08" : : "r"(0) : "memory"); +} + +/* + * Make sure any pending writes are completed before continuing. + */ +#define sync_write_buffer() asm volatile("sync 0" : : : "memory") + +#endif /* __ASM_AVR32_CACHEFLUSH_H */ diff --git a/include/asm-avr32/div64.h b/include/asm-avr32/div64.h new file mode 100644 index 00000000000..2e0ba8389e1 --- /dev/null +++ b/include/asm-avr32/div64.h @@ -0,0 +1,39 @@ +#ifndef _ASM_GENERIC_DIV64_H +#define _ASM_GENERIC_DIV64_H +/* + * Copyright (C) 2003 Bernardo Innocenti + * Based on former asm-ppc/div64.h and asm-m68knommu/div64.h + * + * The semantics of do_div() are: + * + * uint32_t do_div(uint64_t *n, uint32_t base) + * { + * uint32_t remainder = *n % base; + * *n = *n / base; + * return remainder; + * } + * + * NOTE: macro parameter n is evaluated multiple times, + * beware of side effects! + */ + +#include + +extern uint32_t __div64_32(uint64_t *dividend, uint32_t divisor); + +/* The unnecessary pointer compare is there + * to check for type safety (n must be 64bit) + */ +# define do_div(n,base) ({ \ + uint32_t __base = (base); \ + uint32_t __rem; \ + (void)(((typeof((n)) *)0) == ((uint64_t *)0)); \ + if (((n) >> 32) == 0) { \ + __rem = (uint32_t)(n) % __base; \ + (n) = (uint32_t)(n) / __base; \ + } else \ + __rem = __div64_32(&(n), __base); \ + __rem; \ + }) + +#endif /* _ASM_GENERIC_DIV64_H */ diff --git a/include/asm-avr32/dma-mapping.h b/include/asm-avr32/dma-mapping.h new file mode 100644 index 00000000000..3b46fa3e62b --- /dev/null +++ b/include/asm-avr32/dma-mapping.h @@ -0,0 +1,64 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_DMA_MAPPING_H +#define __ASM_AVR32_DMA_MAPPING_H + +#include +#include + +enum dma_data_direction { + DMA_BIDIRECTIONAL = 0, + DMA_TO_DEVICE = 1, + DMA_FROM_DEVICE = 2, +}; +extern void *dma_alloc_coherent(size_t len, unsigned long *handle); + +static inline unsigned long dma_map_single(volatile void *vaddr, size_t len, + enum dma_data_direction dir) +{ + extern void __bad_dma_data_direction(void); + + switch (dir) { + case DMA_BIDIRECTIONAL: + dcache_flush_range(vaddr, len); + break; + case DMA_TO_DEVICE: + dcache_clean_range(vaddr, len); + break; + case DMA_FROM_DEVICE: + dcache_invalidate_range(vaddr, len); + break; + default: + /* This will cause a linker error */ + __bad_dma_data_direction(); + } + + return virt_to_phys(vaddr); +} + +static inline void dma_unmap_single(volatile void *vaddr, size_t len, + unsigned long paddr) +{ + +} + +#endif /* __ASM_AVR32_DMA_MAPPING_H */ diff --git a/include/asm-avr32/errno.h b/include/asm-avr32/errno.h new file mode 100644 index 00000000000..ea3506ff380 --- /dev/null +++ b/include/asm-avr32/errno.h @@ -0,0 +1,132 @@ +#ifndef _ASM_AVR32_ERRNO_H +#define _ASM_AVR32_ERRNO_H + +#define EPERM 1 /* Operation not permitted */ +#define ENOENT 2 /* No such file or directory */ +#define ESRCH 3 /* No such process */ +#define EINTR 4 /* Interrupted system call */ +#define EIO 5 /* I/O error */ +#define ENXIO 6 /* No such device or address */ +#define E2BIG 7 /* Argument list too long */ +#define ENOEXEC 8 /* Exec format error */ +#define EBADF 9 /* Bad file number */ +#define ECHILD 10 /* No child processes */ +#define EAGAIN 11 /* Try again */ +#define ENOMEM 12 /* Out of memory */ +#define EACCES 13 /* Permission denied */ +#define EFAULT 14 /* Bad address */ +#define ENOTBLK 15 /* Block device required */ +#define EBUSY 16 /* Device or resource busy */ +#define EEXIST 17 /* File exists */ +#define EXDEV 18 /* Cross-device link */ +#define ENODEV 19 /* No such device */ +#define ENOTDIR 20 /* Not a directory */ +#define EISDIR 21 /* Is a directory */ +#define EINVAL 22 /* Invalid argument */ +#define ENFILE 23 /* File table overflow */ +#define EMFILE 24 /* Too many open files */ +#define ENOTTY 25 /* Not a typewriter */ +#define ETXTBSY 26 /* Text file busy */ +#define EFBIG 27 /* File too large */ +#define ENOSPC 28 /* No space left on device */ +#define ESPIPE 29 /* Illegal seek */ +#define EROFS 30 /* Read-only file system */ +#define EMLINK 31 /* Too many links */ +#define EPIPE 32 /* Broken pipe */ +#define EDOM 33 /* Math argument out of domain of func */ +#define ERANGE 34 /* Math result not representable */ +#define EDEADLK 35 /* Resource deadlock would occur */ +#define ENAMETOOLONG 36 /* File name too long */ +#define ENOLCK 37 /* No record locks available */ +#define ENOSYS 38 /* Function not implemented */ +#define ENOTEMPTY 39 /* Directory not empty */ +#define ELOOP 40 /* Too many symbolic links encountered */ +#define EWOULDBLOCK EAGAIN /* Operation would block */ +#define ENOMSG 42 /* No message of desired type */ +#define EIDRM 43 /* Identifier removed */ +#define ECHRNG 44 /* Channel number out of range */ +#define EL2NSYNC 45 /* Level 2 not synchronized */ +#define EL3HLT 46 /* Level 3 halted */ +#define EL3RST 47 /* Level 3 reset */ +#define ELNRNG 48 /* Link number out of range */ +#define EUNATCH 49 /* Protocol driver not attached */ +#define ENOCSI 50 /* No CSI structure available */ +#define EL2HLT 51 /* Level 2 halted */ +#define EBADE 52 /* Invalid exchange */ +#define EBADR 53 /* Invalid request descriptor */ +#define EXFULL 54 /* Exchange full */ +#define ENOANO 55 /* No anode */ +#define EBADRQC 56 /* Invalid request code */ +#define EBADSLT 57 /* Invalid slot */ + +#define EDEADLOCK EDEADLK + +#define EBFONT 59 /* Bad font file format */ +#define ENOSTR 60 /* Device not a stream */ +#define ENODATA 61 /* No data available */ +#define ETIME 62 /* Timer expired */ +#define ENOSR 63 /* Out of streams resources */ +#define ENONET 64 /* Machine is not on the network */ +#define ENOPKG 65 /* Package not installed */ +#define EREMOTE 66 /* Object is remote */ +#define ENOLINK 67 /* Link has been severed */ +#define EADV 68 /* Advertise error */ +#define ESRMNT 69 /* Srmount error */ +#define ECOMM 70 /* Communication error on send */ +#define EPROTO 71 /* Protocol error */ +#define EMULTIHOP 72 /* Multihop attempted */ +#define EDOTDOT 73 /* RFS specific error */ +#define EBADMSG 74 /* Not a data message */ +#define EOVERFLOW 75 /* Value too large for defined data type */ +#define ENOTUNIQ 76 /* Name not unique on network */ +#define EBADFD 77 /* File descriptor in bad state */ +#define EREMCHG 78 /* Remote address changed */ +#define ELIBACC 79 /* Can not access a needed shared library */ +#define ELIBBAD 80 /* Accessing a corrupted shared library */ +#define ELIBSCN 81 /* .lib section in a.out corrupted */ +#define ELIBMAX 82 /* Attempting to link in too many shared libraries */ +#define ELIBEXEC 83 /* Cannot exec a shared library directly */ +#define EILSEQ 84 /* Illegal byte sequence */ +#define ERESTART 85 /* Interrupted system call should be restarted */ +#define ESTRPIPE 86 /* Streams pipe error */ +#define EUSERS 87 /* Too many users */ +#define ENOTSOCK 88 /* Socket operation on non-socket */ +#define EDESTADDRREQ 89 /* Destination address required */ +#define EMSGSIZE 90 /* Message too long */ +#define EPROTOTYPE 91 /* Protocol wrong type for socket */ +#define ENOPROTOOPT 92 /* Protocol not available */ +#define EPROTONOSUPPORT 93 /* Protocol not supported */ +#define ESOCKTNOSUPPORT 94 /* Socket type not supported */ +#define EOPNOTSUPP 95 /* Operation not supported on transport endpoint */ +#define EPFNOSUPPORT 96 /* Protocol family not supported */ +#define EAFNOSUPPORT 97 /* Address family not supported by protocol */ +#define EADDRINUSE 98 /* Address already in use */ +#define EADDRNOTAVAIL 99 /* Cannot assign requested address */ +#define ENETDOWN 100 /* Network is down */ +#define ENETUNREACH 101 /* Network is unreachable */ +#define ENETRESET 102 /* Network dropped connection because of reset */ +#define ECONNABORTED 103 /* Software caused connection abort */ +#define ECONNRESET 104 /* Connection reset by peer */ +#define ENOBUFS 105 /* No buffer space available */ +#define EISCONN 106 /* Transport endpoint is already connected */ +#define ENOTCONN 107 /* Transport endpoint is not connected */ +#define ESHUTDOWN 108 /* Cannot send after transport endpoint shutdown */ +#define ETOOMANYREFS 109 /* Too many references: cannot splice */ +#define ETIMEDOUT 110 /* Connection timed out */ +#define ECONNREFUSED 111 /* Connection refused */ +#define EHOSTDOWN 112 /* Host is down */ +#define EHOSTUNREACH 113 /* No route to host */ +#define EALREADY 114 /* Operation already in progress */ +#define EINPROGRESS 115 /* Operation now in progress */ +#define ESTALE 116 /* Stale NFS file handle */ +#define EUCLEAN 117 /* Structure needs cleaning */ +#define ENOTNAM 118 /* Not a XENIX named type file */ +#define ENAVAIL 119 /* No XENIX semaphores available */ +#define EISNAM 120 /* Is a named type file */ +#define EREMOTEIO 121 /* Remote I/O error */ +#define EDQUOT 122 /* Quota exceeded */ + +#define ENOMEDIUM 123 /* No medium found */ +#define EMEDIUMTYPE 124 /* Wrong medium type */ + +#endif /* _ASM_AVR32_ERRNO_H */ diff --git a/include/asm-avr32/global_data.h b/include/asm-avr32/global_data.h new file mode 100644 index 00000000000..01d836c6395 --- /dev/null +++ b/include/asm-avr32/global_data.h @@ -0,0 +1,59 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_GLOBAL_DATA_H__ +#define __ASM_GLOBAL_DATA_H__ + +/* + * The following data structure is placed in some memory wich is + * available very early after boot (like DPRAM on MPC8xx/MPC82xx, or + * some locked parts of the data cache) to allow for a minimum set of + * global variables during system initialization (until we have set + * up the memory controller so that we can use RAM). + * + * Keep it *SMALL* and remember to set CFG_GBL_DATA_SIZE > sizeof(gd_t) + */ + +typedef struct global_data { + bd_t *bd; + unsigned long flags; + const struct device *console_uart; + const struct device *sm; + unsigned long baudrate; + unsigned long sdram_size; + unsigned long have_console; /* serial_init() was called */ + unsigned long reloc_off; /* Relocation Offset */ + unsigned long env_addr; /* Address of env struct */ + unsigned long env_valid; /* Checksum of env valid? */ + unsigned long cpu_hz; /* cpu core clock frequency */ + void **jt; /* jump table */ +} gd_t; + +/* + * Global Data Flags + */ +#define GD_FLG_RELOC 0x00001 /* Code was relocated to RAM */ +#define GD_FLG_DEVINIT 0x00002 /* Devices have been initialized */ +#define GD_FLG_SILENT 0x00004 /* Silent mode */ + +#define DECLARE_GLOBAL_DATA_PTR register gd_t *gd asm("r5") + +#endif /* __ASM_GLOBAL_DATA_H__ */ diff --git a/include/asm-avr32/initcalls.h b/include/asm-avr32/initcalls.h new file mode 100644 index 00000000000..7ba25cde53e --- /dev/null +++ b/include/asm-avr32/initcalls.h @@ -0,0 +1,33 @@ +/* + * Copyright (C) 2005, 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_INITCALLS_H__ +#define __ASM_AVR32_INITCALLS_H__ + +#include + +extern int cpu_init(void); +extern int timer_init(void); +extern void board_init_memories(void); +extern void board_init_pio(void); +extern void board_init_info(void); + +#endif /* __ASM_AVR32_INITCALLS_H__ */ diff --git a/include/asm-avr32/io.h b/include/asm-avr32/io.h new file mode 100644 index 00000000000..e86c456ae1e --- /dev/null +++ b/include/asm-avr32/io.h @@ -0,0 +1,92 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_IO_H +#define __ASM_AVR32_IO_H + +#ifdef __KERNEL__ + +/* + * Generic IO read/write. These perform native-endian accesses. Note + * that some architectures will want to re-define __raw_{read,write}w. + */ +extern void __raw_writesb(unsigned int addr, const void *data, int bytelen); +extern void __raw_writesw(unsigned int addr, const void *data, int wordlen); +extern void __raw_writesl(unsigned int addr, const void *data, int longlen); + +extern void __raw_readsb(unsigned int addr, void *data, int bytelen); +extern void __raw_readsw(unsigned int addr, void *data, int wordlen); +extern void __raw_readsl(unsigned int addr, void *data, int longlen); + +#define __raw_writeb(v,a) (*(volatile unsigned char *)(a) = (v)) +#define __raw_writew(v,a) (*(volatile unsigned short *)(a) = (v)) +#define __raw_writel(v,a) (*(volatile unsigned int *)(a) = (v)) + +#define __raw_readb(a) (*(volatile unsigned char *)(a)) +#define __raw_readw(a) (*(volatile unsigned short *)(a)) +#define __raw_readl(a) (*(volatile unsigned int *)(a)) + +/* As long as I/O is only performed in P4 (or possibly P3), we're safe */ +#define writeb(v,a) __raw_writeb(v,a) +#define writew(v,a) __raw_writew(v,a) +#define writel(v,a) __raw_writel(v,a) + +#define readb(a) __raw_readb(a) +#define readw(a) __raw_readw(a) +#define readl(a) __raw_readl(a) + +/* + * Bad read/write accesses... + */ +extern void __readwrite_bug(const char *fn); + +#define IO_SPACE_LIMIT 0xffffffff + +/* + * All I/O is memory mapped, so these macros doesn't make very much sense + */ +#define outb(v,p) __raw_writeb(v, p) +#define outw(v,p) __raw_writew(cpu_to_le16(v),p) +#define outl(v,p) __raw_writel(cpu_to_le32(v),p) + +#define inb(p) ({ unsigned int __v = __raw_readb(p); __v; }) +#define inw(p) ({ unsigned int __v = __le16_to_cpu(__raw_readw(p)); __v; }) +#define inl(p) ({ unsigned int __v = __le32_to_cpu(__raw_readl(p)); __v; }) + +#include + +/* virt_to_phys will only work when address is in P1 or P2 */ +static __inline__ unsigned long virt_to_phys(volatile void *address) +{ + return PHYSADDR(address); +} + +static __inline__ void * phys_to_virt(unsigned long address) +{ + return (void *)P1SEGADDR(address); +} + +#define cached(addr) ((void *)P1SEGADDR(addr)) +#define uncached(addr) ((void *)P2SEGADDR(addr)) + +#endif /* __KERNEL__ */ + +#endif /* __ASM_AVR32_IO_H */ diff --git a/include/asm-avr32/posix_types.h b/include/asm-avr32/posix_types.h new file mode 100644 index 00000000000..edf1bc14d25 --- /dev/null +++ b/include/asm-avr32/posix_types.h @@ -0,0 +1,144 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_POSIX_TYPES_H +#define __ASM_AVR32_POSIX_TYPES_H + +/* + * This file is generally used by user-level software, so you need to + * be a little careful about namespace pollution etc. Also, we cannot + * assume GCC is being used. + */ + +typedef unsigned long __kernel_dev_t; +typedef unsigned long __kernel_ino_t; +typedef unsigned short __kernel_mode_t; +typedef unsigned short __kernel_nlink_t; +typedef long __kernel_off_t; +typedef int __kernel_pid_t; +typedef unsigned short __kernel_ipc_pid_t; +typedef unsigned int __kernel_uid_t; +typedef unsigned int __kernel_gid_t; +typedef unsigned long __kernel_size_t; +typedef int __kernel_ssize_t; +typedef int __kernel_ptrdiff_t; +typedef long __kernel_time_t; +typedef long __kernel_suseconds_t; +typedef long __kernel_clock_t; +typedef int __kernel_timer_t; +typedef int __kernel_clockid_t; +typedef int __kernel_daddr_t; +typedef char * __kernel_caddr_t; +typedef unsigned short __kernel_uid16_t; +typedef unsigned short __kernel_gid16_t; +typedef unsigned int __kernel_uid32_t; +typedef unsigned int __kernel_gid32_t; + +typedef unsigned short __kernel_old_uid_t; +typedef unsigned short __kernel_old_gid_t; +typedef unsigned short __kernel_old_dev_t; + +#ifdef __GNUC__ +typedef long long __kernel_loff_t; +#endif + +typedef struct { +#if defined(__KERNEL__) || defined(__USE_ALL) + int val[2]; +#else /* !defined(__KERNEL__) && !defined(__USE_ALL) */ + int __val[2]; +#endif /* !defined(__KERNEL__) && !defined(__USE_ALL) */ +} __kernel_fsid_t; + +#if defined(__KERNEL__) + +#undef __FD_SET +static __inline__ void __FD_SET(unsigned long __fd, __kernel_fd_set *__fdsetp) +{ + unsigned long __tmp = __fd / __NFDBITS; + unsigned long __rem = __fd % __NFDBITS; + __fdsetp->fds_bits[__tmp] |= (1UL<<__rem); +} + +#undef __FD_CLR +static __inline__ void __FD_CLR(unsigned long __fd, __kernel_fd_set *__fdsetp) +{ + unsigned long __tmp = __fd / __NFDBITS; + unsigned long __rem = __fd % __NFDBITS; + __fdsetp->fds_bits[__tmp] &= ~(1UL<<__rem); +} + + +#undef __FD_ISSET +static __inline__ int __FD_ISSET(unsigned long __fd, const __kernel_fd_set *__p) +{ + unsigned long __tmp = __fd / __NFDBITS; + unsigned long __rem = __fd % __NFDBITS; + return (__p->fds_bits[__tmp] & (1UL<<__rem)) != 0; +} + +/* + * This will unroll the loop for the normal constant case (8 ints, + * for a 256-bit fd_set) + */ +#undef __FD_ZERO +static __inline__ void __FD_ZERO(__kernel_fd_set *__p) +{ + unsigned long *__tmp = __p->fds_bits; + int __i; + + if (__builtin_constant_p(__FDSET_LONGS)) { + switch (__FDSET_LONGS) { + case 16: + __tmp[ 0] = 0; __tmp[ 1] = 0; + __tmp[ 2] = 0; __tmp[ 3] = 0; + __tmp[ 4] = 0; __tmp[ 5] = 0; + __tmp[ 6] = 0; __tmp[ 7] = 0; + __tmp[ 8] = 0; __tmp[ 9] = 0; + __tmp[10] = 0; __tmp[11] = 0; + __tmp[12] = 0; __tmp[13] = 0; + __tmp[14] = 0; __tmp[15] = 0; + return; + + case 8: + __tmp[ 0] = 0; __tmp[ 1] = 0; + __tmp[ 2] = 0; __tmp[ 3] = 0; + __tmp[ 4] = 0; __tmp[ 5] = 0; + __tmp[ 6] = 0; __tmp[ 7] = 0; + return; + + case 4: + __tmp[ 0] = 0; __tmp[ 1] = 0; + __tmp[ 2] = 0; __tmp[ 3] = 0; + return; + } + } + __i = __FDSET_LONGS; + while (__i) { + __i--; + *__tmp = 0; + __tmp++; + } +} + +#endif /* defined(__KERNEL__) */ + +#endif /* __ASM_AVR32_POSIX_TYPES_H */ diff --git a/include/asm-avr32/processor.h b/include/asm-avr32/processor.h new file mode 100644 index 00000000000..cc59dfad56b --- /dev/null +++ b/include/asm-avr32/processor.h @@ -0,0 +1,97 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_PROCESSOR_H +#define __ASM_AVR32_PROCESSOR_H + +#ifndef __ASSEMBLY__ + +#define current_text_addr() ({ void *pc; __asm__("mov %0,pc" : "=r"(pc)); pc; }) + +struct avr32_cpuinfo { + unsigned long loops_per_jiffy; +}; + +extern struct avr32_cpuinfo boot_cpu_data; + +#ifdef CONFIG_SMP +extern struct avr32_cpuinfo cpu_data[]; +#define current_cpu_data cpu_data[smp_processor_id()] +#else +#define cpu_data (&boot_cpu_data) +#define current_cpu_data boot_cpu_data +#endif + +/* TODO: Make configurable (2GB will serve as a reasonable default) */ +#define TASK_SIZE 0x80000000 + +/* This decides where the kernel will search for a free chunk of vm + * space during mmap's + */ +#define TASK_UNMAPPED_BASE (TASK_SIZE / 3) + +#define cpu_relax() barrier() +#define cpu_sync_pipeline() asm volatile("sub pc, -2" : : : "memory") + +/* This struct contains the CPU context as stored by switch_to() */ +struct thread_struct { + unsigned long pc; + unsigned long ksp; /* Kernel stack pointer */ + unsigned long r7; + unsigned long r6; + unsigned long r5; + unsigned long r4; + unsigned long r3; + unsigned long r2; + unsigned long r1; + unsigned long r0; +}; + +#define INIT_THREAD { \ + .ksp = sizeof(init_stack) + (long)&init_stack, \ +} + +/* + * Do necessary setup to start up a newly executed thread. + */ +#define start_thread(regs, new_pc, new_sp) \ + set_fs(USER_DS); \ + regs->sr = 0; /* User mode. */ \ + regs->gr[REG_PC] = new_pc; \ + regs->gr[REG_SP] = new_sp + +struct task_struct; + +/* Free all resources held by a thread */ +extern void release_thread(struct task_struct *); + +/* Create a kernel thread without removing it from tasklists */ +extern int kernel_thread(int (*fn)(void *), void *arg, unsigned long flags); + +/* Prepare to copy thread state - unlazy all lazy status */ +#define prepare_to_copy(tsk) do { } while(0) + +/* Return saved PC of a blocked thread */ +#define thread_saved_pc(tsk) (tsk->thread.pc) + +#endif /* __ASSEMBLY__ */ + +#endif /* __ASM_AVR32_PROCESSOR_H */ diff --git a/include/asm-avr32/ptrace.h b/include/asm-avr32/ptrace.h new file mode 100644 index 00000000000..c770ba02c30 --- /dev/null +++ b/include/asm-avr32/ptrace.h @@ -0,0 +1,148 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_PTRACE_H +#define __ASM_AVR32_PTRACE_H + +/* + * Status Register bits + */ +#define SR_H 0x40000000 +#define SR_R 0x20000000 +#define SR_J 0x10000000 +#define SR_DM 0x08000000 +#define SR_D 0x04000000 +#define MODE_NMI 0x01c00000 +#define MODE_EXCEPTION 0x01800000 +#define MODE_INT3 0x01400000 +#define MODE_INT2 0x01000000 +#define MODE_INT1 0x00c00000 +#define MODE_INT0 0x00800000 +#define MODE_SUPERVISOR 0x00400000 +#define MODE_USER 0x00000000 +#define MODE_MASK 0x01c00000 +#define SR_EM 0x00200000 +#define SR_I3M 0x00100000 +#define SR_I2M 0x00080000 +#define SR_I1M 0x00040000 +#define SR_I0M 0x00020000 +#define SR_GM 0x00010000 + +#define MODE_SHIFT 22 +#define SR_EM_BIT 21 +#define SR_I3M_BIT 20 +#define SR_I2M_BIT 19 +#define SR_I1M_BIT 18 +#define SR_I0M_BIT 17 +#define SR_GM_BIT 16 + +/* The user-visible part */ +#define SR_Q 0x00000010 +#define SR_V 0x00000008 +#define SR_N 0x00000004 +#define SR_Z 0x00000002 +#define SR_C 0x00000001 + +/* + * The order is defined by the stdsp instruction. r0 is stored first, so it + * gets the highest address. + * + * Registers 0-12 are general-purpose registers (r12 is normally used for + * the function return value). + * Register 13 is the stack pointer + * Register 14 is the link register + * Register 15 is the program counter + */ +#define FRAME_SIZE_FULL 72 +#define REG_R12_ORIG 68 +#define REG_R0 64 +#define REG_R1 60 +#define REG_R2 56 +#define REG_R3 52 +#define REG_R4 48 +#define REG_R5 44 +#define REG_R6 40 +#define REG_R7 36 +#define REG_R8 32 +#define REG_R9 28 +#define REG_R10 34 +#define REG_R11 20 +#define REG_R12 16 +#define REG_SP 12 +#define REG_LR 8 + +#define FRAME_SIZE_MIN 8 +#define REG_PC 4 +#define REG_SR 0 + +#ifndef __ASSEMBLY__ +struct pt_regs { + /* These are always saved */ + unsigned long sr; + unsigned long pc; + + /* These are sometimes saved */ + unsigned long lr; + unsigned long sp; + unsigned long r12; + unsigned long r11; + unsigned long r10; + unsigned long r9; + unsigned long r8; + unsigned long r7; + unsigned long r6; + unsigned long r5; + unsigned long r4; + unsigned long r3; + unsigned long r2; + unsigned long r1; + unsigned long r0; + + /* Only saved on system call */ + unsigned long r12_orig; +}; + +#ifdef __KERNEL__ +# define user_mode(regs) (((regs)->sr & MODE_MASK) == MODE_USER) +# define instruction_pointer(regs) ((regs)->pc) +extern void show_regs (struct pt_regs *); + +static __inline__ int valid_user_regs(struct pt_regs *regs) +{ + /* + * Some of the Java bits might be acceptable if/when we + * implement some support for that stuff... + */ + if ((regs->sr & 0xffff0000) == 0) + return 1; + + /* + * Force status register flags to be sane and report this + * illegal behaviour... + */ + regs->sr &= 0x0000ffff; + return 0; +} +#endif + +#endif /* ! __ASSEMBLY__ */ + +#endif /* __ASM_AVR32_PTRACE_H */ diff --git a/include/asm-avr32/sdram.h b/include/asm-avr32/sdram.h new file mode 100644 index 00000000000..5057eefa8ad --- /dev/null +++ b/include/asm-avr32/sdram.h @@ -0,0 +1,33 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_SDRAM_H +#define __ASM_AVR32_SDRAM_H + +struct sdram_info { + unsigned long phys_addr; + unsigned int row_bits, col_bits, bank_bits; + unsigned int cas, twr, trc, trp, trcd, tras, txsr; +}; + +extern unsigned long sdram_init(const struct sdram_info *info); + +#endif /* __ASM_AVR32_SDRAM_H */ diff --git a/include/asm-avr32/sections.h b/include/asm-avr32/sections.h new file mode 100644 index 00000000000..75373abde73 --- /dev/null +++ b/include/asm-avr32/sections.h @@ -0,0 +1,39 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_SECTIONS_H +#define __ASM_AVR32_SECTIONS_H + +/* References to section boundaries */ + +extern char _text[], _etext[]; +extern char __flashprog_start[], __flashprog_end[]; +extern char _data[], __data_lma[], _edata[], __edata_lma[]; +extern char __got_start[], __got_lma[], __got_end[]; +extern char _end[]; + +/* + * Everything in .flashprog will be locked in the icache so it doesn't + * get disturbed when executing flash commands. + */ +#define __flashprog __attribute__((section(".flashprog"), __noinline__)) + +#endif /* __ASM_AVR32_SECTIONS_H */ diff --git a/include/asm-avr32/setup.h b/include/asm-avr32/setup.h new file mode 100644 index 00000000000..e6ef8d6b50c --- /dev/null +++ b/include/asm-avr32/setup.h @@ -0,0 +1,142 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * Based on linux/include/asm-arm/setup.h + * Copyright (C) 1997-1999 Russel King + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_SETUP_H__ +#define __ASM_AVR32_SETUP_H__ + +#define COMMAND_LINE_SIZE 256 + +/* Magic number indicating that a tag table is present */ +#define ATAG_MAGIC 0xa2a25441 + +#ifndef __ASSEMBLY__ + +/* + * Generic memory range, used by several tags. + * + * addr is always physical. + * size is measured in bytes. + * next is for use by the OS, e.g. for grouping regions into + * linked lists. + */ +struct tag_mem_range { + u32 addr; + u32 size; + struct tag_mem_range * next; +}; + +/* The list ends with an ATAG_NONE node. */ +#define ATAG_NONE 0x00000000 + +struct tag_header { + u32 size; + u32 tag; +}; + +/* The list must start with an ATAG_CORE node */ +#define ATAG_CORE 0x54410001 + +struct tag_core { + u32 flags; + u32 pagesize; + u32 rootdev; +}; + +/* it is allowed to have multiple ATAG_MEM nodes */ +#define ATAG_MEM 0x54410002 +/* ATAG_MEM uses tag_mem_range */ + +/* command line: \0 terminated string */ +#define ATAG_CMDLINE 0x54410003 + +struct tag_cmdline { + char cmdline[1]; /* this is the minimum size */ +}; + +/* Ramdisk image (may be compressed) */ +#define ATAG_RDIMG 0x54410004 +/* ATAG_RDIMG uses tag_mem_range */ + +/* Information about various clocks present in the system */ +#define ATAG_CLOCK 0x54410005 + +struct tag_clock { + u32 clock_id; /* Which clock are we talking about? */ + u32 clock_flags; /* Special features */ + u64 clock_hz; /* Clock speed in Hz */ +}; + +/* The clock types we know about */ +#define ACLOCK_BOOTCPU 0 /* The CPU we're booting from */ +#define ACLOCK_HSB 1 /* Deprecated */ + +/* Memory reserved for the system (e.g. the bootloader) */ +#define ATAG_RSVD_MEM 0x54410006 +/* ATAG_RSVD_MEM uses tag_mem_range */ + +/* Ethernet information */ + +#define ATAG_ETHERNET 0x54410007 + +struct tag_ethernet { + u8 mac_index; + u8 mii_phy_addr; + u8 hw_address[6]; +}; + +#define AETH_INVALID_PHY 0xff + +struct tag { + struct tag_header hdr; + union { + struct tag_core core; + struct tag_mem_range mem_range; + struct tag_cmdline cmdline; + struct tag_clock clock; + struct tag_ethernet ethernet; + } u; +}; + +struct tagtable { + u32 tag; + int (*parse)(struct tag *); +}; + +#define __tag __attribute_used__ __attribute__((__section__(".taglist"))) +#define __tagtable(tag, fn) \ + static struct tagtable __tagtable_##fn __tag = { tag, fn } + +#define tag_member_present(tag,member) \ + ((unsigned long)(&((struct tag *)0L)->member + 1) \ + <= (tag)->hdr.size * 4) + +#define tag_next(t) ((struct tag *)((u32 *)(t) + (t)->hdr.size)) +#define tag_size(type) ((sizeof(struct tag_header) + sizeof(struct type)) >> 2) + +#define for_each_tag(t,base) \ + for (t = base; t->hdr.size; t = tag_next(t)) + +#endif /* !__ASSEMBLY__ */ + +#endif /* __ASM_AVR32_SETUP_H__ */ diff --git a/include/asm-avr32/string.h b/include/asm-avr32/string.h new file mode 100644 index 00000000000..8b05d1a031e --- /dev/null +++ b/include/asm-avr32/string.h @@ -0,0 +1,28 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_STRING_H +#define __ASM_AVR32_STRING_H + +#define __HAVE_ARCH_MEMSET +extern void *memset(void *s, int c, size_t n); + +#endif /* __ASM_AVR32_STRING_H */ diff --git a/include/asm-avr32/sysreg.h b/include/asm-avr32/sysreg.h new file mode 100644 index 00000000000..72ad49e5e2d --- /dev/null +++ b/include/asm-avr32/sysreg.h @@ -0,0 +1,279 @@ +/* + * System registers for AVR32 + */ +#ifndef __ASM_AVR32_SYSREG_H__ +#define __ASM_AVR32_SYSREG_H__ + +/* system register offsets */ +#define SYSREG_SR 0x0000 +#define SYSREG_EVBA 0x0004 +#define SYSREG_ACBA 0x0008 +#define SYSREG_CPUCR 0x000c +#define SYSREG_ECR 0x0010 +#define SYSREG_RSR_SUP 0x0014 +#define SYSREG_RSR_INT0 0x0018 +#define SYSREG_RSR_INT1 0x001c +#define SYSREG_RSR_INT2 0x0020 +#define SYSREG_RSR_INT3 0x0024 +#define SYSREG_RSR_EX 0x0028 +#define SYSREG_RSR_NMI 0x002c +#define SYSREG_RSR_DBG 0x0030 +#define SYSREG_RAR_SUP 0x0034 +#define SYSREG_RAR_INT0 0x0038 +#define SYSREG_RAR_INT1 0x003c +#define SYSREG_RAR_INT2 0x0040 +#define SYSREG_RAR_INT3 0x0044 +#define SYSREG_RAR_EX 0x0048 +#define SYSREG_RAR_NMI 0x004c +#define SYSREG_RAR_DBG 0x0050 +#define SYSREG_JECR 0x0054 +#define SYSREG_JOSP 0x0058 +#define SYSREG_JAVA_LV0 0x005c +#define SYSREG_JAVA_LV1 0x0060 +#define SYSREG_JAVA_LV2 0x0064 +#define SYSREG_JAVA_LV3 0x0068 +#define SYSREG_JAVA_LV4 0x006c +#define SYSREG_JAVA_LV5 0x0070 +#define SYSREG_JAVA_LV6 0x0074 +#define SYSREG_JAVA_LV7 0x0078 +#define SYSREG_JTBA 0x007c +#define SYSREG_JBCR 0x0080 +#define SYSREG_CONFIG0 0x0100 +#define SYSREG_CONFIG1 0x0104 +#define SYSREG_COUNT 0x0108 +#define SYSREG_COMPARE 0x010c +#define SYSREG_TLBEHI 0x0110 +#define SYSREG_TLBELO 0x0114 +#define SYSREG_PTBR 0x0118 +#define SYSREG_TLBEAR 0x011c +#define SYSREG_MMUCR 0x0120 +#define SYSREG_TLBARLO 0x0124 +#define SYSREG_TLBARHI 0x0128 +#define SYSREG_PCCNT 0x012c +#define SYSREG_PCNT0 0x0130 +#define SYSREG_PCNT1 0x0134 +#define SYSREG_PCCR 0x0138 +#define SYSREG_BEAR 0x013c +#define SYSREG_SABAL 0x0300 +#define SYSREG_SABAH 0x0304 +#define SYSREG_SABD 0x0308 + +/* Bitfields in SR */ +#define SYSREG_SR_C_OFFSET 0 +#define SYSREG_SR_C_SIZE 1 +#define SYSREG_Z_OFFSET 1 +#define SYSREG_Z_SIZE 1 +#define SYSREG_SR_N_OFFSET 2 +#define SYSREG_SR_N_SIZE 1 +#define SYSREG_SR_V_OFFSET 3 +#define SYSREG_SR_V_SIZE 1 +#define SYSREG_Q_OFFSET 4 +#define SYSREG_Q_SIZE 1 +#define SYSREG_L_OFFSET 5 +#define SYSREG_L_SIZE 1 +#define SYSREG_T_OFFSET 14 +#define SYSREG_T_SIZE 1 +#define SYSREG_SR_R_OFFSET 15 +#define SYSREG_SR_R_SIZE 1 +#define SYSREG_GM_OFFSET 16 +#define SYSREG_GM_SIZE 1 +#define SYSREG_I0M_OFFSET 17 +#define SYSREG_I0M_SIZE 1 +#define SYSREG_I1M_OFFSET 18 +#define SYSREG_I1M_SIZE 1 +#define SYSREG_I2M_OFFSET 19 +#define SYSREG_I2M_SIZE 1 +#define SYSREG_I3M_OFFSET 20 +#define SYSREG_I3M_SIZE 1 +#define SYSREG_EM_OFFSET 21 +#define SYSREG_EM_SIZE 1 +#define SYSREG_M0_OFFSET 22 +#define SYSREG_M0_SIZE 1 +#define SYSREG_M1_OFFSET 23 +#define SYSREG_M1_SIZE 1 +#define SYSREG_M2_OFFSET 24 +#define SYSREG_M2_SIZE 1 +#define SYSREG_SR_D_OFFSET 26 +#define SYSREG_SR_D_SIZE 1 +#define SYSREG_DM_OFFSET 27 +#define SYSREG_DM_SIZE 1 +#define SYSREG_SR_J_OFFSET 28 +#define SYSREG_SR_J_SIZE 1 +#define SYSREG_H_OFFSET 29 +#define SYSREG_H_SIZE 1 + +/* Bitfields in CPUCR */ +#define SYSREG_BI_OFFSET 0 +#define SYSREG_BI_SIZE 1 +#define SYSREG_BE_OFFSET 1 +#define SYSREG_BE_SIZE 1 +#define SYSREG_FE_OFFSET 2 +#define SYSREG_FE_SIZE 1 +#define SYSREG_RE_OFFSET 3 +#define SYSREG_RE_SIZE 1 +#define SYSREG_IBE_OFFSET 4 +#define SYSREG_IBE_SIZE 1 +#define SYSREG_IEE_OFFSET 5 +#define SYSREG_IEE_SIZE 1 + +/* Bitfields in ECR */ +#define SYSREG_ECR_OFFSET 0 +#define SYSREG_ECR_SIZE 32 + +/* Bitfields in CONFIG0 */ +#define SYSREG_CONFIG0_R_OFFSET 0 +#define SYSREG_CONFIG0_R_SIZE 1 +#define SYSREG_CONFIG0_D_OFFSET 1 +#define SYSREG_CONFIG0_D_SIZE 1 +#define SYSREG_CONFIG0_S_OFFSET 2 +#define SYSREG_CONFIG0_S_SIZE 1 +#define SYSREG_O_OFFSET 3 +#define SYSREG_O_SIZE 1 +#define SYSREG_P_OFFSET 4 +#define SYSREG_P_SIZE 1 +#define SYSREG_CONFIG0_J_OFFSET 5 +#define SYSREG_CONFIG0_J_SIZE 1 +#define SYSREG_F_OFFSET 6 +#define SYSREG_F_SIZE 1 +#define SYSREG_MMUT_OFFSET 7 +#define SYSREG_MMUT_SIZE 3 +#define SYSREG_AR_OFFSET 10 +#define SYSREG_AR_SIZE 3 +#define SYSREG_AT_OFFSET 13 +#define SYSREG_AT_SIZE 3 +#define SYSREG_PROCESSORREVISION_OFFSET 16 +#define SYSREG_PROCESSORREVISION_SIZE 8 +#define SYSREG_PROCESSORID_OFFSET 24 +#define SYSREG_PROCESSORID_SIZE 8 + +/* Bitfields in CONFIG1 */ +#define SYSREG_DASS_OFFSET 0 +#define SYSREG_DASS_SIZE 3 +#define SYSREG_DLSZ_OFFSET 3 +#define SYSREG_DLSZ_SIZE 3 +#define SYSREG_DSET_OFFSET 6 +#define SYSREG_DSET_SIZE 4 +#define SYSREG_IASS_OFFSET 10 +#define SYSREG_IASS_SIZE 3 +#define SYSREG_ILSZ_OFFSET 13 +#define SYSREG_ILSZ_SIZE 3 +#define SYSREG_ISET_OFFSET 16 +#define SYSREG_ISET_SIZE 4 +#define SYSREG_DMMUSZ_OFFSET 20 +#define SYSREG_DMMUSZ_SIZE 6 +#define SYSREG_IMMUSZ_OFFSET 26 +#define SYSREG_IMMUSZ_SIZE 6 + +/* Bitfields in TLBEHI */ +#define SYSREG_ASID_OFFSET 0 +#define SYSREG_ASID_SIZE 8 +#define SYSREG_TLBEHI_I_OFFSET 8 +#define SYSREG_TLBEHI_I_SIZE 1 +#define SYSREG_TLBEHI_V_OFFSET 9 +#define SYSREG_TLBEHI_V_SIZE 1 +#define SYSREG_VPN_OFFSET 10 +#define SYSREG_VPN_SIZE 22 + +/* Bitfields in TLBELO */ +#define SYSREG_W_OFFSET 0 +#define SYSREG_W_SIZE 1 +#define SYSREG_TLBELO_D_OFFSET 1 +#define SYSREG_TLBELO_D_SIZE 1 +#define SYSREG_SZ_OFFSET 2 +#define SYSREG_SZ_SIZE 2 +#define SYSREG_AP_OFFSET 4 +#define SYSREG_AP_SIZE 3 +#define SYSREG_B_OFFSET 7 +#define SYSREG_B_SIZE 1 +#define SYSREG_G_OFFSET 8 +#define SYSREG_G_SIZE 1 +#define SYSREG_TLBELO_C_OFFSET 9 +#define SYSREG_TLBELO_C_SIZE 1 +#define SYSREG_PFN_OFFSET 10 +#define SYSREG_PFN_SIZE 22 + +/* Bitfields in MMUCR */ +#define SYSREG_E_OFFSET 0 +#define SYSREG_E_SIZE 1 +#define SYSREG_M_OFFSET 1 +#define SYSREG_M_SIZE 1 +#define SYSREG_MMUCR_I_OFFSET 2 +#define SYSREG_MMUCR_I_SIZE 1 +#define SYSREG_MMUCR_N_OFFSET 3 +#define SYSREG_MMUCR_N_SIZE 1 +#define SYSREG_MMUCR_S_OFFSET 4 +#define SYSREG_MMUCR_S_SIZE 1 +#define SYSREG_DLA_OFFSET 8 +#define SYSREG_DLA_SIZE 6 +#define SYSREG_DRP_OFFSET 14 +#define SYSREG_DRP_SIZE 6 +#define SYSREG_ILA_OFFSET 20 +#define SYSREG_ILA_SIZE 6 +#define SYSREG_IRP_OFFSET 26 +#define SYSREG_IRP_SIZE 6 + +/* Bitfields in PCCR */ +#define SYSREG_PCCR_R_OFFSET 1 +#define SYSREG_PCCR_R_SIZE 1 +#define SYSREG_PCCR_C_OFFSET 2 +#define SYSREG_PCCR_C_SIZE 1 +#define SYSREG_PCCR_S_OFFSET 3 +#define SYSREG_PCCR_S_SIZE 1 +#define SYSREG_IEC_OFFSET 4 +#define SYSREG_IEC_SIZE 1 +#define SYSREG_IE0_OFFSET 5 +#define SYSREG_IE0_SIZE 1 +#define SYSREG_IE1_OFFSET 6 +#define SYSREG_IE1_SIZE 1 +#define SYSREG_FC_OFFSET 8 +#define SYSREG_FC_SIZE 1 +#define SYSREG_F0_OFFSET 9 +#define SYSREG_F0_SIZE 1 +#define SYSREG_F1_OFFSET 10 +#define SYSREG_F1_SIZE 1 +#define SYSREG_CONF0_OFFSET 12 +#define SYSREG_CONF0_SIZE 6 +#define SYSREG_CONF1_OFFSET 18 +#define SYSREG_CONF1_SIZE 6 + +/* Constants for ECR */ +#define ECR_UNRECOVERABLE 0 +#define ECR_TLB_MULTIPLE 1 +#define ECR_BUS_ERROR_WRITE 2 +#define ECR_BUS_ERROR_READ 3 +#define ECR_NMI 4 +#define ECR_ADDR_ALIGN_X 5 +#define ECR_PROTECTION_X 6 +#define ECR_DEBUG 7 +#define ECR_ILLEGAL_OPCODE 8 +#define ECR_UNIMPL_INSTRUCTION 9 +#define ECR_PRIVILEGE_VIOLATION 10 +#define ECR_FPE 11 +#define ECR_COPROC_ABSENT 12 +#define ECR_ADDR_ALIGN_R 13 +#define ECR_ADDR_ALIGN_W 14 +#define ECR_PROTECTION_R 15 +#define ECR_PROTECTION_W 16 +#define ECR_DTLB_MODIFIED 17 +#define ECR_TLB_MISS_X 20 +#define ECR_TLB_MISS_R 24 +#define ECR_TLB_MISS_W 28 + +/* Bit manipulation macros */ +#define SYSREG_BIT(name) (1 << SYSREG_##name##_OFFSET) +#define SYSREG_BF(name,value) \ + (((value) & ((1 << SYSREG_##name##_SIZE) - 1)) \ + << SYSREG_##name##_OFFSET) +#define SYSREG_BFEXT(name,value) \ + (((value) >> SYSREG_##name##_OFFSET) \ + & ((1 << SYSREG_##name##_SIZE) - 1)) +#define SYSREG_BFINS(name,value,old) \ + (((old) & ~(((1 << SYSREG_##name##_SIZE) - 1) \ + << SYSREG_##name##_OFFSET)) \ + | SYSREG_BF(name,value)) + +/* Register access macros */ +#define sysreg_read(reg) __builtin_mfsr(SYSREG_##reg) +#define sysreg_write(reg, value) __builtin_mtsr(SYSREG_##reg, value) + +#endif /* __ASM_AVR32_SYSREG_H__ */ diff --git a/include/asm-avr32/types.h b/include/asm-avr32/types.h new file mode 100644 index 00000000000..e6c65d9179b --- /dev/null +++ b/include/asm-avr32/types.h @@ -0,0 +1,84 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_TYPES_H +#define __ASM_AVR32_TYPES_H + +#ifndef __ASSEMBLY__ + +typedef unsigned short umode_t; + +/* + * __xx is ok: it doesn't pollute the POSIX namespace. Use these in the + * header files exported to user space + */ +typedef __signed__ char __s8; +typedef unsigned char __u8; + +typedef __signed__ short __s16; +typedef unsigned short __u16; + +typedef __signed__ int __s32; +typedef unsigned int __u32; + +#if defined(__GNUC__) && !defined(__STRICT_ANSI__) +typedef __signed__ long long __s64; +typedef unsigned long long __u64; +#endif + +#endif /* __ASSEMBLY__ */ + +/* + * These aren't exported outside the kernel to avoid name space clashes + */ +#ifdef __KERNEL__ + +#define BITS_PER_LONG 32 + +#ifndef __ASSEMBLY__ + +typedef __signed__ char s8; +typedef unsigned char u8; + +typedef __signed__ short s16; +typedef unsigned short u16; + +typedef __signed__ int s32; +typedef unsigned int u32; + +typedef __signed__ long long s64; +typedef unsigned long long u64; + +/* Dma addresses are 32-bits wide. */ + +typedef u32 dma_addr_t; + +#ifdef CONFIG_LBD +typedef u64 sector_t; +#define HAVE_SECTOR_T +#endif + +#endif /* __ASSEMBLY__ */ + +#endif /* __KERNEL__ */ + + +#endif /* __ASM_AVR32_TYPES_H */ diff --git a/include/asm-avr32/u-boot.h b/include/asm-avr32/u-boot.h new file mode 100644 index 00000000000..71dfcaf2840 --- /dev/null +++ b/include/asm-avr32/u-boot.h @@ -0,0 +1,56 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_U_BOOT_H__ +#define __ASM_U_BOOT_H__ 1 + +typedef struct bd_info { + unsigned long bi_baudrate; + unsigned long bi_ip_addr; + unsigned char bi_enetaddr[6]; + unsigned char bi_phy_id[4]; + struct environment_s *bi_env; + unsigned long bi_board_number; + void *bi_boot_params; + struct { + unsigned long start; + unsigned long size; + } bi_dram[CONFIG_NR_DRAM_BANKS]; + unsigned long bi_flashstart; + unsigned long bi_flashsize; + unsigned long bi_flashoffset; +} bd_t; + +#define bi_memstart bi_dram[0].start +#define bi_memsize bi_dram[0].size + +/** + * container_of - cast a member of a structure out to the containing structure + * + * @ptr: the pointer to the member. + * @type: the type of the container struct this is embedded in. + * @member: the name of the member within the struct. + */ +#define container_of(ptr, type, member) ({ \ + const typeof( ((type *)0)->member ) *__mptr = (ptr); \ + (type *)( (char *)__mptr - offsetof(type,member) );}) + +#endif /* __ASM_U_BOOT_H__ */ diff --git a/lib_avr32/Makefile b/lib_avr32/Makefile new file mode 100644 index 00000000000..5b6300ba78a --- /dev/null +++ b/lib_avr32/Makefile @@ -0,0 +1,47 @@ +# +# (C) Copyright 2002-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# (C) Copyright 2004-2006 Atmel Corporation +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(ARCH).a + +SOBJS = memset.o + +COBJS = board.o interrupts.o avr32_linux.o div64.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) crv $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/lib_avr32/avr32_linux.c b/lib_avr32/avr32_linux.c new file mode 100644 index 00000000000..d128dfb53f0 --- /dev/null +++ b/lib_avr32/avr32_linux.c @@ -0,0 +1,315 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +extern int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); + +/* CPU-specific hook to allow flushing of caches, etc. */ +extern void prepare_to_boot(void); + +#ifdef CONFIG_SHOW_BOOT_PROGRESS +# include +# define SHOW_BOOT_PROGRESS(arg) show_boot_progress(arg) +#else +# define SHOW_BOOT_PROGRESS(arg) +#endif + +extern image_header_t header; /* from cmd_bootm.c */ + +static struct tag *setup_start_tag(struct tag *params) +{ + params->hdr.tag = ATAG_CORE; + params->hdr.size = tag_size(tag_core); + + params->u.core.flags = 0; + params->u.core.pagesize = 4096; + params->u.core.rootdev = 0; + + return tag_next(params); +} + +static struct tag *setup_memory_tags(struct tag *params) +{ + bd_t *bd = gd->bd; + int i; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + params->hdr.tag = ATAG_MEM; + params->hdr.size = tag_size(tag_mem_range); + + params->u.mem_range.addr = bd->bi_dram[i].start; + params->u.mem_range.size = bd->bi_dram[i].size; + + params = tag_next(params); + } + + return params; +} + +static struct tag *setup_commandline_tag(struct tag *params, char *cmdline) +{ + if (!cmdline) + return params; + + /* eat leading white space */ + while (*cmdline == ' ') cmdline++; + + /* + * Don't include tags for empty command lines; let the kernel + * use its default command line. + */ + if (*cmdline == '\0') + return params; + + params->hdr.tag = ATAG_CMDLINE; + params->hdr.size = + (sizeof (struct tag_header) + strlen(cmdline) + 1 + 3) >> 2; + strcpy(params->u.cmdline.cmdline, cmdline); + + return tag_next(params); +} + +static struct tag *setup_ramdisk_tag(struct tag *params, + unsigned long rd_start, + unsigned long rd_end) +{ + if (rd_start == rd_end) + return params; + + params->hdr.tag = ATAG_RDIMG; + params->hdr.size = tag_size(tag_mem_range); + + params->u.mem_range.addr = rd_start; + params->u.mem_range.size = rd_end - rd_start; + + return tag_next(params); +} + +static struct tag *setup_clock_tags(struct tag *params) +{ + params->hdr.tag = ATAG_CLOCK; + params->hdr.size = tag_size(tag_clock); + params->u.clock.clock_id = ACLOCK_BOOTCPU; + params->u.clock.clock_flags = 0; + params->u.clock.clock_hz = gd->cpu_hz; + +#ifdef CONFIG_AT32AP7000 + /* + * New kernels don't need this, but we should be backwards + * compatible for a while... + */ + params = tag_next(params); + + params->hdr.tag = ATAG_CLOCK; + params->hdr.size = tag_size(tag_clock); + params->u.clock.clock_id = ACLOCK_HSB; + params->u.clock.clock_flags = 0; + params->u.clock.clock_hz = pm_get_clock_freq(CLOCK_HSB); +#endif + + return tag_next(params); +} + +static struct tag *setup_ethernet_tag(struct tag *params, + char *addr, int index) +{ + char *s, *e; + int i; + + params->hdr.tag = ATAG_ETHERNET; + params->hdr.size = tag_size(tag_ethernet); + + params->u.ethernet.mac_index = index; + params->u.ethernet.mii_phy_addr = gd->bd->bi_phy_id[index]; + + s = addr; + for (i = 0; i < 6; i++) { + params->u.ethernet.hw_address[i] = simple_strtoul(s, &e, 16); + s = e + 1; + } + + return tag_next(params); +} + +static struct tag *setup_ethernet_tags(struct tag *params) +{ + char name[16] = "ethaddr"; + char *addr; + int i = 0; + + do { + addr = getenv(name); + if (addr) + params = setup_ethernet_tag(params, addr, i); + sprintf(name, "eth%daddr", ++i); + } while (i < 4); + + return params; +} + +static void setup_end_tag(struct tag *params) +{ + params->hdr.tag = ATAG_NONE; + params->hdr.size = 0; +} + +void do_bootm_linux(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[], + unsigned long addr, unsigned long *len_ptr, int verify) +{ + unsigned long data, len = 0; + unsigned long initrd_start, initrd_end; + unsigned long image_start, image_end; + unsigned long checksum; + void (*theKernel)(int magic, void *tagtable); + image_header_t *hdr; + struct tag *params, *params_start; + char *commandline = getenv("bootargs"); + + hdr = (image_header_t *)addr; + image_start = addr; + image_end = addr + hdr->ih_size; + + theKernel = (void *)ntohl(hdr->ih_ep); + + /* + * Check if there is an initrd image + */ + if (argc >= 3) { + SHOW_BOOT_PROGRESS(9); + + addr = simple_strtoul(argv[2], NULL, 16); + + printf("## Loading RAMDISK image at %08lx ...\n", addr); + + memcpy(&header, (char *)addr, sizeof(header)); + hdr = &header; + + if (ntohl(hdr->ih_magic) != IH_MAGIC) { + puts("Bad Magic Number\n"); + SHOW_BOOT_PROGRESS(-10); + do_reset(cmdtp, flag, argc, argv); + } + + data = (unsigned long)hdr; + len = sizeof(*hdr); + checksum = ntohl(hdr->ih_hcrc); + hdr->ih_hcrc = 0; + + if (crc32(0, (unsigned char *)data, len) != checksum) { + puts("Bad Header Checksum\n"); + SHOW_BOOT_PROGRESS(-11); + do_reset(cmdtp, flag, argc, argv); + } + + SHOW_BOOT_PROGRESS(10); + + print_image_hdr(hdr); + + data = addr + sizeof(header); + len = ntohl(hdr->ih_size); + + if (verify) { + unsigned long csum = 0; + + puts(" Verifying Checksum ... "); + csum = crc32(0, (unsigned char *)data, len); + if (csum != ntohl(hdr->ih_dcrc)) { + puts("Bad Data CRC\n"); + SHOW_BOOT_PROGRESS(-12); + do_reset(cmdtp, flag, argc, argv); + } + puts("OK\n"); + } + + SHOW_BOOT_PROGRESS(11); + + if ((hdr->ih_os != IH_OS_LINUX) || + (hdr->ih_arch != IH_CPU_AVR32) || + (hdr->ih_type != IH_TYPE_RAMDISK)) { + puts("Not a Linux/AVR32 RAMDISK image\n"); + SHOW_BOOT_PROGRESS(-13); + do_reset(cmdtp, flag, argc, argv); + } + } else if ((hdr->ih_type == IH_TYPE_MULTI) && (len_ptr[1])) { + ulong tail = ntohl (len_ptr[0]) % 4; + int i; + + SHOW_BOOT_PROGRESS (13); + + /* skip kernel length and terminator */ + data = (ulong) (&len_ptr[2]); + /* skip any additional image length fields */ + for (i = 1; len_ptr[i]; ++i) + data += 4; + /* add kernel length, and align */ + data += ntohl (len_ptr[0]); + if (tail) { + data += 4 - tail; + } + + len = ntohl (len_ptr[1]); + } else { + /* no initrd image */ + SHOW_BOOT_PROGRESS(14); + len = data = 0; + } + + if (data) { + initrd_start = data; + initrd_end = initrd_start + len; + } else { + initrd_start = 0; + initrd_end = 0; + } + + SHOW_BOOT_PROGRESS(15); + + params = params_start = (struct tag *)gd->bd->bi_boot_params; + params = setup_start_tag(params); + params = setup_memory_tags(params); + if (initrd_start) { + params = setup_ramdisk_tag(params, + PHYSADDR(initrd_start), + PHYSADDR(initrd_end)); + } + params = setup_commandline_tag(params, commandline); + params = setup_clock_tags(params); + params = setup_ethernet_tags(params); + setup_end_tag(params); + + printf("\nStarting kernel at %p (params at %p)...\n\n", + theKernel, params_start); + + prepare_to_boot(); + + theKernel(ATAG_MAGIC, params_start); +} diff --git a/lib_avr32/board.c b/lib_avr32/board.c new file mode 100644 index 00000000000..02c106b80ed --- /dev/null +++ b/lib_avr32/board.c @@ -0,0 +1,175 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include +#include +#include +#include +#include + +#include +#include + +#ifndef CONFIG_IDENT_STRING +#define CONFIG_IDENT_STRING "" +#endif + +DECLARE_GLOBAL_DATA_PTR; + +const char version_string[] = + U_BOOT_VERSION " (" __DATE__ " - " __TIME__ ") " CONFIG_IDENT_STRING; + +unsigned long monitor_flash_len; + +/* + * Begin and end of memory area for malloc(), and current "brk" + */ +static unsigned long mem_malloc_start = 0; +static unsigned long mem_malloc_end = 0; +static unsigned long mem_malloc_brk = 0; + +/* The malloc area is wherever the board wants it to be */ +static void mem_malloc_init(void) +{ + mem_malloc_start = CFG_MALLOC_START; + mem_malloc_end = CFG_MALLOC_END; + mem_malloc_brk = mem_malloc_start; + + printf("malloc: Using memory from 0x%08lx to 0x%08lx\n", + mem_malloc_start, mem_malloc_end); + + memset ((void *)mem_malloc_start, 0, + mem_malloc_end - mem_malloc_start); +} + +void *sbrk(ptrdiff_t increment) +{ + unsigned long old = mem_malloc_brk; + unsigned long new = old + increment; + + if ((new < mem_malloc_start) || (new > mem_malloc_end)) + return NULL; + + mem_malloc_brk = new; + return ((void *)old); +} + +static int init_baudrate(void) +{ + char tmp[64]; + int i; + + i = getenv_r("baudrate", tmp, sizeof(tmp)); + if (i > 0) { + gd->baudrate = simple_strtoul(tmp, NULL, 10); + } else { + gd->baudrate = CONFIG_BAUDRATE; + } + return 0; +} + + +static int display_banner (void) +{ + printf ("\n\n%s\n\n", version_string); + printf ("U-Boot code: %p -> %p data: %p -> %p\n", + _text, _etext, _data, _end); + return 0; +} + +void hang(void) +{ + for (;;) ; +} + +static int display_dram_config (void) +{ + int i; + + puts ("DRAM Configuration:\n"); + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + printf ("Bank #%d: %08lx ", i, gd->bd->bi_dram[i].start); + print_size (gd->bd->bi_dram[i].size, "\n"); + } + + return 0; +} + +static void display_flash_config (void) +{ + puts ("Flash: "); + print_size(gd->bd->bi_flashsize, " "); + printf("at address 0x%08lx\n", gd->bd->bi_flashstart); +} + +void start_u_boot (void) +{ + gd_t gd_data; + + /* Initialize the global data pointer */ + memset(&gd_data, 0, sizeof(gd_data)); + gd = &gd_data; + + monitor_flash_len = _edata - _text; + + /* Perform initialization sequence */ + cpu_init(); + timer_init(); + env_init(); + init_baudrate(); + serial_init(); + console_init_f(); + display_banner(); + + board_init_memories(); + mem_malloc_init(); + + gd->bd = malloc(sizeof(bd_t)); + memset(gd->bd, 0, sizeof(bd_t)); + gd->bd->bi_baudrate = gd->baudrate; + gd->bd->bi_dram[0].start = CFG_SDRAM_BASE; + gd->bd->bi_dram[0].size = gd->sdram_size; + + board_init_info(); + flash_init(); + + if (gd->bd->bi_flashsize) + display_flash_config(); + if (gd->bd->bi_dram[0].size) + display_dram_config(); + + gd->bd->bi_boot_params = malloc(CFG_BOOTPARAMS_LEN); + if (!gd->bd->bi_boot_params) + puts("WARNING: Cannot allocate space for boot parameters\n"); + + /* initialize environment */ + env_relocate(); + + devices_init(); + jumptable_init(); + console_init_r(); + + for (;;) { + main_loop(); + } +} diff --git a/lib_avr32/div64.c b/lib_avr32/div64.c new file mode 100644 index 00000000000..99726e325da --- /dev/null +++ b/lib_avr32/div64.c @@ -0,0 +1,54 @@ +/* + * Copyright (C) 2003 Bernardo Innocenti + * + * Based on former do_div() implementation from asm-parisc/div64.h: + * Copyright (C) 1999 Hewlett-Packard Co + * Copyright (C) 1999 David Mosberger-Tang + * + * + * Generic C version of 64bit/32bit division and modulo, with + * 64bit result and 32bit remainder. + * + * The fast case for (n>>32 == 0) is handled inline by do_div(). + * + * Code generated for this function might be very inefficient + * for some CPUs. __div64_32() can be overridden by linking arch-specific + * assembly versions such as arch/ppc/lib/div64.S and arch/sh/lib/div64.S. + */ + +#include + +#include + +uint32_t __div64_32(uint64_t *n, uint32_t base) +{ + uint64_t rem = *n; + uint64_t b = base; + uint64_t res, d = 1; + uint32_t high = rem >> 32; + + /* Reduce the thing a bit first */ + res = 0; + if (high >= base) { + high /= base; + res = (uint64_t) high << 32; + rem -= (uint64_t) (high*base) << 32; + } + + while ((int64_t)b > 0 && b < rem) { + b = b+b; + d = d+d; + } + + do { + if (rem >= b) { + rem -= b; + res += d; + } + b >>= 1; + d >>= 1; + } while (d); + + *n = res; + return rem; +} diff --git a/lib_avr32/interrupts.c b/lib_avr32/interrupts.c new file mode 100644 index 00000000000..ce538f3d924 --- /dev/null +++ b/lib_avr32/interrupts.c @@ -0,0 +1,39 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include + +#include + +void enable_interrupts(void) +{ + asm volatile("csrf %0" : : "n"(SYSREG_GM_OFFSET)); +} + +int disable_interrupts(void) +{ + unsigned long sr; + + sr = sysreg_read(SR); + asm volatile("ssrf %0" : : "n"(SYSREG_GM_OFFSET)); + + return SYSREG_BFEXT(GM, sr); +} diff --git a/lib_avr32/memset.S b/lib_avr32/memset.S new file mode 100644 index 00000000000..dc3b09b42f9 --- /dev/null +++ b/lib_avr32/memset.S @@ -0,0 +1,81 @@ +/* + * Copyright (C) 2004-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + /* + * r12: void *b + * r11: int c + * r10: size_t len + * + * Returns b in r12 + */ + .text + + .global memset + .type memset, @function + .align 2 +memset: + mov r9, r12 + mov r8, r12 + or r11, r11, r11 << 8 + andl r9, 3, COH + brne 1f + +2: or r11, r11, r11 << 16 + sub r10, 4 + brlt 5f + + /* Let's do some real work */ +4: st.w r8++, r11 + sub r10, 4 + brge 4b + + /* + * When we get here, we've got less than 4 bytes to set. r10 + * might be negative. + */ +5: sub r10, -4 + reteq r12 + + /* Fastpath ends here, exactly 32 bytes from memset */ + + /* Handle unaligned count or pointer */ + bld r10, 1 + brcc 6f + st.b r8++, r11 + st.b r8++, r11 + bld r10, 0 + retcc r12 +6: st.b r8++, r11 + mov pc, lr + + /* Handle unaligned pointer */ +1: sub r10, 4 + brlt 5b + add r10, r9 + lsl r9, 1 + add pc, r9 + st.b r8++, r11 + st.b r8++, r11 + st.b r8++, r11 + rjmp 2b + + .size memset, . - memset -- cgit v1.3.1 From 856f054410cef52d868feb330168b2a4c4091328 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 28 Oct 2006 15:55:52 +0200 Subject: [PATCH] NAND: Partition name support added to NAND subsystem chpart, nboot and NAND subsystem related commands now accept also partition name to specify offset. Signed-off-by: Ladislav Michl Signed-off-by: Stefan Roese --- common/cmd_jffs2.c | 14 +- common/cmd_nand.c | 346 ++++++++++++++++++++++++++--------------------- doc/README.nand | 29 ++-- drivers/nand/nand_util.c | 11 +- 4 files changed, 226 insertions(+), 174 deletions(-) (limited to 'doc') diff --git a/common/cmd_jffs2.c b/common/cmd_jffs2.c index b5fd41724f6..7fd1fa33daf 100644 --- a/common/cmd_jffs2.c +++ b/common/cmd_jffs2.c @@ -1300,7 +1300,7 @@ static void list_partitions(void) * Given partition identifier in form of , find * corresponding device and verify partition number. * - * @param id string describing device and partition + * @param id string describing device and partition or partition name * @param dev pointer to the requested device (output) * @param part_num verified partition number (output) * @param part pointer to requested partition (output) @@ -1309,11 +1309,23 @@ static void list_partitions(void) int find_dev_and_part(const char *id, struct mtd_device **dev, u8 *part_num, struct part_info **part) { + struct list_head *dentry, *pentry; u8 type, dnum, pnum; const char *p; DEBUGF("--- find_dev_and_part ---\nid = %s\n", id); + list_for_each(dentry, &devices) { + *part_num = 0; + *dev = list_entry(dentry, struct mtd_device, link); + list_for_each(pentry, &(*dev)->parts) { + *part = list_entry(pentry, struct part_info, link); + if (strcmp((*part)->name, id) == 0) + return 0; + (*part_num)++; + } + } + p = id; *dev = NULL; *part = NULL; diff --git a/common/cmd_nand.c b/common/cmd_nand.c index 4fb3b65960d..7286726f1c1 100644 --- a/common/cmd_nand.c +++ b/common/cmd_nand.c @@ -36,6 +36,15 @@ #include #include +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) + +/* parition handling routines */ +int mtdparts_init(void); +int id_parse(const char *id, const char **ret_id, u8 *dev_type, u8 *dev_num); +int find_dev_and_part(const char *id, struct mtd_device **dev, + u8 *part_num, struct part_info **part); +#endif + extern nand_info_t nand_info[]; /* info for NAND chips */ static int nand_dump_oob(nand_info_t *nand, ulong off) @@ -83,50 +92,75 @@ static int nand_dump(nand_info_t *nand, ulong off) /* ------------------------------------------------------------------------- */ -static void -arg_off_size(int argc, char *argv[], ulong *off, ulong *size, ulong totsize) +static inline int str2long(char *p, ulong *num) { - *off = 0; - *size = 0; + char *endptr; -#if defined(CONFIG_JFFS2_NAND) && defined(CFG_JFFS_CUSTOM_PART) - if (argc >= 1 && strcmp(argv[0], "partition") == 0) { - int part_num; - struct part_info *part; - const char *partstr; - - if (argc >= 2) - partstr = argv[1]; - else - partstr = getenv("partition"); - - if (partstr) - part_num = (int)simple_strtoul(partstr, NULL, 10); - else - part_num = 0; + *num = simple_strtoul(p, &endptr, 16); + return (*p != '\0' && *endptr == '\0') ? 1 : 0; +} - part = jffs2_part_info(part_num); - if (part == NULL) { - printf("\nInvalid partition %d\n", part_num); - return; +static int +arg_off_size(int argc, char *argv[], nand_info_t *nand, ulong *off, ulong *size) +{ + int idx = nand_curr_device; +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) + struct mtd_device *dev; + struct part_info *part; + u8 pnum; + + if (argc >= 1 && !(str2long(argv[0], off))) { + if ((mtdparts_init() == 0) && + (find_dev_and_part(argv[0], &dev, &pnum, &part) == 0)) { + if (dev->id->type != MTD_DEV_TYPE_NAND) { + puts("not a NAND device\n"); + return -1; + } + *off = part->offset; + if (argc >= 2) { + if (!(str2long(argv[1], size))) { + printf("'%s' is not a number\n", argv[1]); + return -1; + } + if (*size > part->size) + *size = part->size; + } else { + *size = part->size; + } + idx = dev->id->num; + *nand = nand_info[idx]; + goto out; } - *size = part->size; - *off = (ulong)part->offset; - } else + } #endif - { - if (argc >= 1) - *off = (ulong)simple_strtoul(argv[0], NULL, 16); - else - *off = 0; - if (argc >= 2) - *size = (ulong)simple_strtoul(argv[1], NULL, 16); - else - *size = totsize - *off; + if (argc >= 1) { + if (!(str2long(argv[0], off))) { + printf("'%s' is not a number\n", argv[0]); + return -1; + } + } else { + *off = 0; + } + if (argc >= 2) { + if (!(str2long(argv[1], size))) { + printf("'%s' is not a number\n", argv[1]); + return -1; + } + } else { + *size = nand->size - *off; } +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) +out: +#endif + printf("device %d ", idx); + if (*size == nand->size) + puts("whole chip\n"); + else + printf("offset 0x%x, size 0x%x\n", *off, *size); + return 0; } int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) @@ -213,35 +247,22 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) return 0; } + /* + * Syntax is: + * 0 1 2 3 4 + * nand erase [clean] [off size] + */ if (strcmp(cmd, "erase") == 0 || strcmp(cmd, "scrub") == 0) { nand_erase_options_t opts; - int clean = argc >= 3 && !strcmp("clean", argv[2]); - int rest_argc = argc - 2; - char **rest_argv = argv + 2; + /* "clean" at index 2 means request to write cleanmarker */ + int clean = argc > 2 && !strcmp("clean", argv[2]); + int o = clean ? 3 : 2; int scrub = !strcmp(cmd, "scrub"); - if (clean) { - rest_argc--; - rest_argv++; - } - - if (rest_argc == 0) { - - printf("\nNAND %s: device %d whole chip\n", - cmd, - nand_curr_device); - - off = size = 0; - } else { - arg_off_size(rest_argc, rest_argv, &off, &size, - nand->size); - - if (off == 0 && size == 0) - return 1; - - printf("\nNAND %s: device %d offset 0x%x, size 0x%x\n", - cmd, nand_curr_device, off, size); - } + printf("\nNAND %s: ", scrub ? "scrub" : "erase"); + /* skip first two or three arguments, look for offset and size */ + if (arg_off_size(argc - o, argv + o, nand, &off, &size) != 0) + return 1; memset(&opts, 0, sizeof(opts)); opts.offset = off; @@ -250,23 +271,22 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) opts.quiet = quiet; if (scrub) { - printf("Warning: " - "scrub option will erase all factory set " - "bad blocks!\n" - " " - "There is no reliable way to recover them.\n" - " " - "Use this command only for testing purposes " - "if you\n" - " " - "are sure of what you are doing!\n" - "\nReally scrub this NAND flash? \n" - ); + puts("Warning: " + "scrub option will erase all factory set " + "bad blocks!\n" + " " + "There is no reliable way to recover them.\n" + " " + "Use this command only for testing purposes " + "if you\n" + " " + "are sure of what you are doing!\n" + "\nReally scrub this NAND flash? \n"); if (getc() == 'y' && getc() == '\r') { opts.scrub = 1; } else { - printf("scrub aborted\n"); + puts("scrub aborted\n"); return -1; } } @@ -301,13 +321,10 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) addr = (ulong)simple_strtoul(argv[2], NULL, 16); - arg_off_size(argc - 3, argv + 3, &off, &size, nand->size); - if (off == 0 && size == 0) - return 1; - read = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ - printf("\nNAND %s: device %d offset %u, size %u ... ", - read ? "read" : "write", nand_curr_device, off, size); + printf("\nNAND %s: ", read ? "read" : "write"); + if (arg_off_size(argc - 3, argv + 3, nand, &off, &size) != 0) + return 1; s = strchr(cmd, '.'); if (s != NULL && @@ -334,15 +351,13 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) opts.quiet = quiet; ret = nand_write_opts(nand, &opts); } - printf("%s\n", ret ? "ERROR" : "OK"); - return ret == 0 ? 0 : 1; + } else { + if (read) + ret = nand_read(nand, off, &size, (u_char *)addr); + else + ret = nand_write(nand, off, &size, (u_char *)addr); } - if (read) - ret = nand_read(nand, off, &size, (u_char *)addr); - else - ret = nand_write(nand, off, &size, (u_char *)addr); - printf(" %d bytes %s: %s\n", size, read ? "read" : "written", ret ? "ERROR" : "OK"); @@ -412,9 +427,9 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } } else { if (!nand_lock(nand, tight)) { - printf ("NAND flash successfully locked\n"); + puts("NAND flash successfully locked\n"); } else { - printf ("Error locking NAND flash. \n"); + puts("Error locking NAND flash\n"); return 1; } } @@ -422,19 +437,14 @@ int do_nand(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) } if (strcmp(cmd, "unlock") == 0) { - if (argc == 2) { - off = 0; - size = nand->size; - } else { - arg_off_size(argc - 2, argv + 2, &off, &size, - nand->size); - } + if (arg_off_size(argc - 2, argv + 2, nand, &off, &size) < 0) + return 1; if (!nand_unlock(nand, off, size)) { - printf("NAND flash successfully unlocked\n"); + puts("NAND flash successfully unlocked\n"); } else { - printf("Error unlocking NAND flash. " - "Write and erase will probably fail\n"); + puts("Error unlocking NAND flash, " + "write and erase will probably fail\n"); return 1; } return 0; @@ -449,8 +459,8 @@ U_BOOT_CMD(nand, 5, 1, do_nand, "nand - NAND sub-system\n", "info - show available NAND devices\n" "nand device [dev] - show or set current device\n" - "nand read[.jffs2] - addr off size\n" - "nand write[.jffs2] - addr off size - read/write `size' bytes starting\n" + "nand read[.jffs2] - addr off|partition size\n" + "nand write[.jffs2] - addr off|partiton size - read/write `size' bytes starting\n" " at offset `off' to/from memory address `addr'\n" "nand erase [clean] [off size] - erase `size' bytes from\n" " offset `off' (entire device if not specified)\n" @@ -462,62 +472,20 @@ U_BOOT_CMD(nand, 5, 1, do_nand, "nand lock [tight] [status] - bring nand to lock state or display locked pages\n" "nand unlock [offset] [size] - unlock section\n"); -int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +static int nand_load_image(cmd_tbl_t *cmdtp, nand_info_t *nand, + ulong offset, ulong addr, char *cmd) { - char *boot_device = NULL; - char *ep; - int dev; int r; - ulong addr, cnt, offset = 0; + char *ep; + ulong cnt; image_header_t *hdr; - nand_info_t *nand; - switch (argc) { - case 1: - addr = CFG_LOAD_ADDR; - boot_device = getenv("bootdevice"); - break; - case 2: - addr = simple_strtoul(argv[1], NULL, 16); - boot_device = getenv("bootdevice"); - break; - case 3: - addr = simple_strtoul(argv[1], NULL, 16); - boot_device = argv[2]; - break; - case 4: - addr = simple_strtoul(argv[1], NULL, 16); - boot_device = argv[2]; - offset = simple_strtoul(argv[3], NULL, 16); - break; - default: - printf("Usage:\n%s\n", cmdtp->usage); - SHOW_BOOT_PROGRESS(-1); - return 1; - } - - if (!boot_device) { - puts("\n** No boot device **\n"); - SHOW_BOOT_PROGRESS(-1); - return 1; - } - - dev = simple_strtoul(boot_device, &ep, 16); - - if (dev < 0 || dev >= CFG_MAX_NAND_DEVICE || !nand_info[dev].name) { - printf("\n** Device %d not available\n", dev); - SHOW_BOOT_PROGRESS(-1); - return 1; - } - - nand = &nand_info[dev]; - printf("\nLoading from device %d: %s (offset 0x%lx)\n", - dev, nand->name, offset); + printf("\nLoading from %s, offset 0x%lx\n", nand->name, offset); cnt = nand->oobblock; r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { - printf("** Read error on %d\n", dev); + puts("** Read error\n"); SHOW_BOOT_PROGRESS(-1); return 1; } @@ -536,7 +504,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) r = nand_read(nand, offset, &cnt, (u_char *) addr); if (r) { - printf("** Read error on %d\n", dev); + puts("** Read error\n"); SHOW_BOOT_PROGRESS(-1); return 1; } @@ -550,7 +518,7 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) char *local_args[2]; extern int do_bootm(cmd_tbl_t *, int, int, char *[]); - local_args[0] = argv[0]; + local_args[0] = cmd; local_args[1] = NULL; printf("Automatic boot of image at addr 0x%08lx ...\n", addr); @@ -561,9 +529,83 @@ int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) return 0; } -U_BOOT_CMD(nboot, 4, 1, do_nandboot, - "nboot - boot from NAND device\n", "loadAddr dev\n"); +int do_nandboot(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) +{ + char *boot_device = NULL; + int idx; + ulong addr, offset = 0; +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) + struct mtd_device *dev; + struct part_info *part; + u8 pnum; + + if (argc >= 2) { + char *p = (argc == 2) ? argv[1] : argv[2]; + if (!(str2long(p, &addr)) && (mtdparts_init() == 0) && + (find_dev_and_part(p, &dev, &pnum, &part) == 0)) { + if (dev->id->type != MTD_DEV_TYPE_NAND) { + puts("Not a NAND device\n"); + return 1; + } + if (argc > 3) + goto usage; + if (argc == 3) + addr = simple_strtoul(argv[2], NULL, 16); + else + addr = CFG_LOAD_ADDR; + return nand_load_image(cmdtp, &nand_info[dev->id->num], + part->offset, addr, argv[0]); + } + } +#endif + switch (argc) { + case 1: + addr = CFG_LOAD_ADDR; + boot_device = getenv("bootdevice"); + break; + case 2: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = getenv("bootdevice"); + break; + case 3: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = argv[2]; + break; + case 4: + addr = simple_strtoul(argv[1], NULL, 16); + boot_device = argv[2]; + offset = simple_strtoul(argv[3], NULL, 16); + break; + default: +#if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) +usage: +#endif + printf("Usage:\n%s\n", cmdtp->usage); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + if (!boot_device) { + puts("\n** No boot device **\n"); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + idx = simple_strtoul(boot_device, NULL, 16); + + if (idx < 0 || idx >= CFG_MAX_NAND_DEVICE || !nand_info[idx].name) { + printf("\n** Device %d not available\n", idx); + SHOW_BOOT_PROGRESS(-1); + return 1; + } + + return nand_load_image(cmdtp, &nand_info[idx], offset, addr, argv[0]); +} + +U_BOOT_CMD(nboot, 4, 1, do_nandboot, + "nboot - boot from NAND device\n", + "[partition] | [[[loadAddr] dev] offset]\n"); #endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff --git a/doc/README.nand b/doc/README.nand index 5279a4f2bc5..b5171f4d407 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -34,14 +34,19 @@ Commands: nand device num Make device `num' the current device and print information about it. - nand erase off size - nand erase clean [off size] - Erase `size' bytes starting at offset `off'. Only complete erase - blocks can be erased. + nand erase off|partition size + nand erase clean [off|partition size] + Erase `size' bytes starting at offset `off'. Alternatively partition + name can be specified, in this case size will be eventually limited + to not exceed partition size (this behaviour applies also to read + and write commands). Only complete erase blocks can be erased. + + If `erase' is specified without an offset or size, the entire flash + is erased. If `erase' is specified with partition but without an + size, the entire partition is erased. If `clean' is specified, a JFFS2-style clean marker is written to - each block after it is erased. If `clean' is specified without an - offset or size, the entire flash is erased. + each block after it is erased. This command will not erase blocks that are marked bad. There is a debug option in cmd_nand.c to allow bad blocks to be erased. @@ -51,28 +56,28 @@ Commands: nand info Print information about all of the NAND devices found. - nand read addr ofs size + nand read addr ofs|partition size Read `size' bytes from `ofs' in NAND flash to `addr'. If a page cannot be read because it is marked bad or an uncorrectable data error is found the command stops with an error. - nand read.jffs2 addr ofs size + nand read.jffs2 addr ofs|partition size Like `read', but the data for blocks that are marked bad is read as 0xff. This gives a readable JFFS2 image that can be processed by the JFFS2 commands such as ls and fsload. - nand read.oob addr ofs size + nand read.oob addr ofs|partition size Read `size' bytes from the out-of-band data area corresponding to `ofs' in NAND flash to `addr'. This is limited to the 16 bytes of data for one 512-byte page or 2 256-byte pages. There is no check for bad blocks or ECC errors. - nand write addr ofs size + nand write addr ofs|partition size Write `size' bytes from `addr' to `ofs' in NAND flash. If a page cannot be written because it is marked bad or the write fails the command stops with an error. - nand write.jffs2 addr ofs size + nand write.jffs2 addr ofs|partition size Like `write', but blocks that are marked bad are skipped and the is written to the next block instead. This allows writing writing a JFFS2 image, as long as the image is short enough to fit even @@ -80,7 +85,7 @@ Commands: produced by mkfs.jffs2 should work well, but loading an image copied from another flash is going to be trouble if there are any bad blocks. - nand write.oob addr ofs size + nand write.oob addr ofs|partition size Write `size' bytes from `addr' to the out-of-band data area corresponding to `ofs' in NAND flash. This is limited to the 16 bytes of data for one 512-byte page or 2 256-byte pages. There is no check diff --git a/drivers/nand/nand_util.c b/drivers/nand/nand_util.c index 7570210d5ca..10bf03659ed 100644 --- a/drivers/nand/nand_util.c +++ b/drivers/nand/nand_util.c @@ -83,15 +83,8 @@ int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts) erase.mtd = meminfo; erase.len = meminfo->erasesize; - if (opts->offset == 0 && opts->length == 0) { - /* erase complete chip */ - erase.addr = 0; - erase_length = meminfo->size; - } else { - /* erase specified region */ - erase.addr = opts->offset; - erase_length = opts->length; - } + erase.addr = opts->offset; + erase_length = opts->length; isNAND = meminfo->type == MTD_NANDFLASH ? 1 : 0; -- cgit v1.3.1