From 4c52783b3d024e153c4972b97332e314bc3bdc46 Mon Sep 17 00:00:00 2001 From: roy zang Date: Thu, 2 Nov 2006 18:49:51 +0800 Subject: General code modification for mpc7448hpc2 board support. 1. Add 7447A and 7448 processor support. 2. Add the following flags. CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically (such as by switch on board), this flag should be set. CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot relocates to RAM, this flag should be set. CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the system hang in exception, this flag should be set. There is a design issue for tsi108/109 pci configure read. When pci scan the slots, if there is no pci card, the tsi108/9 will cause a machine check exception for mpc7448 processor. Signed-off-by: Alexandre Bounine Signed-off-by: Roy Zang --- drivers/Makefile | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/Makefile b/drivers/Makefile index 5a369df2c41..6a3ea5da255 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -35,8 +35,8 @@ COBJS = 3c589.o 5701rls.o ali512x.o atmel_usart.o \ lan91c96.o \ natsemi.o ne2000.o netarm_eth.o netconsole.o \ ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \ - omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o \ - pcnet.o plb2800_eth.o \ + omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o tsi108_pci.o\ + tsi108_i2c.o pcnet.o plb2800_eth.o \ ps2ser.o ps2mult.o pc_keyb.o \ rtl8019.o rtl8139.o rtl8169.o \ s3c4510b_eth.o s3c4510b_uart.o \ @@ -45,7 +45,7 @@ COBJS = 3c589.o 5701rls.o ali512x.o atmel_usart.o \ serial_pl010.o serial_pl011.o serial_xuartlite.o \ sl811_usb.o sm501.o smc91111.o smiLynxEM.o \ status_led.o sym53c8xx.o ahci.o \ - ti_pci1410a.o tigon3.o tsec.o \ + ti_pci1410a.o tigon3.o tsec.o tsi108_eth.o\ usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \ videomodes.o w83c553f.o \ ks8695eth.o \ -- cgit v1.3.1 From d1927cee977126e547ceeba23e4f978f377cfb8f Mon Sep 17 00:00:00 2001 From: roy zang Date: Thu, 2 Nov 2006 19:08:55 +0800 Subject: Tundra tsi108 on chip Ethernet controller support. The following is a brief description of the Ethernet controller: The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to manage the two physical connection devices (PHYs). Each Ethernet port has its own statistics monitor that tracks and reports key interface statistics. Each port supports a 256-entry hash table for address filtering. In addition, each port is bridged to the Switch Fabric through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO. Each Ethernet port also has a pair of internal Ethernet DMA channels to support the transmit and receive data flows. The Ethernet DMA channels use descriptors set up in memory, the memory map of the device, and access via the Switch Fabric. The Ethernet Controller?s DMA arbiter handles arbitration for the Switch Fabric. The Controller also has a register businterface for register accesses and status monitor control. The PMD (Physical Media Device) interface operates in MII, GMII, or TBI modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs. The GMII and TBI modes are used to connect with Gigabit PMDs. Internal data flows to and from the Ethernet Controller through the Switch Fabric. Each Ethernet port uses its transmit and receive DMA channels to manage data flows through buffer descriptors that are predefined by the system (the descriptors can exist anywhere in the system memory map). These descriptors are data structures that point to buffers filled with data ready to transmit over Ethernet, or they point to empty buffers ready to receive data from Ethernet. Signed-off-by: Alexandre Bounine Signed-off-by: Roy Zang --- drivers/tsi108_eth.c | 1043 ++++++++++++++++++++++++++++++++++++++++++++++++++ net/eth.c | 4 + 2 files changed, 1047 insertions(+) create mode 100644 drivers/tsi108_eth.c (limited to 'drivers') diff --git a/drivers/tsi108_eth.c b/drivers/tsi108_eth.c new file mode 100644 index 00000000000..d95a047ce85 --- /dev/null +++ b/drivers/tsi108_eth.c @@ -0,0 +1,1043 @@ +/*********************************************************************** + * + * Copyright (c) 2005 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * Description: + * Ethernet interface for Tundra TSI108 bridge chip + * + ***********************************************************************/ + +#include + +#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) \ + && defined(CONFIG_TSI108_ETH) + +#if !defined(CONFIG_TSI108_ETH_NUM_PORTS) || (CONFIG_TSI108_ETH_NUM_PORTS > 2) +#error "CONFIG_TSI108_ETH_NUM_PORTS must be defined as 1 or 2" +#endif + +#include +#include +#include +#include + +#ifdef DEBUG +#define TSI108_ETH_DEBUG 7 +#else +#define TSI108_ETH_DEBUG 0 +#endif + +#if TSI108_ETH_DEBUG > 0 +#define debug_lev(lev, fmt, args...) if (lev <= TSI108_ETH_DEBUG) printf("%s %d: " fmt, __FUNCTION__, __LINE__, ##args) +#else +#define debug_lev(lev, fmt, args...) do{}while(0) +#endif + +#define RX_PRINT_ERRORS +#define TX_PRINT_ERRORS + +#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000) + +#define ETH_PORT_OFFSET 0x400 + +#define __REG32(base, offset) (*((volatile u32 *)((char *)(base) + (offset)))) + +#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000) +#define MAC_CONFIG_1_TX_ENABLE (0x00000001) +#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002) +#define MAC_CONFIG_1_RX_ENABLE (0x00000004) +#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008) +#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010) +#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020) +#define MAC_CONFIG_1_LOOP_BACK (0x00000100) +#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000) +#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000) +#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000) +#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000) +#define MAC_CONFIG_1_SIM_RESET (0x40000000) +#define MAC_CONFIG_1_SOFT_RESET (0x80000000) + +#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004) +#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001) +#define MAC_CONFIG_2_CRC_ENABLE (0x00000002) +#define MAC_CONFIG_2_PAD_CRC (0x00000004) +#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010) +#define MAC_CONFIG_2_HUGE_FRAME (0x00000020) +#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8) +#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12) +#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */ +#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */ + +#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010) + +#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020) +#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7) +#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010) +#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020) +#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000) + +#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024) +#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001) +#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002) + +#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028) +#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c) +#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030) + +#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034) +#define MII_MGMT_INDICATORS_BUSY (0x00000001) +#define MII_MGMT_INDICATORS_SCAN (0x00000002) +#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004) + +#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c) +#define INTERFACE_STATUS_LINK_FAIL (0x00000008) +#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200) + +#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040) +#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044) + +#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200) +#define PORT_CONTROL_PRI (0x00000001) +#define PORT_CONTROL_BPT (0x00010000) +#define PORT_CONTROL_SPD (0x00040000) +#define PORT_CONTROL_RBC (0x00080000) +#define PORT_CONTROL_PRB (0x00200000) +#define PORT_CONTROL_DIS (0x00400000) +#define PORT_CONTROL_TBI (0x00800000) +#define PORT_CONTROL_STE (0x10000000) +#define PORT_CONTROL_ZOR (0x20000000) +#define PORT_CONTROL_CLR (0x40000000) +#define PORT_CONTROL_SRT (0x80000000) + +#define reg_TX_CONFIG(base) __REG32(base, 0x00000220) +#define TX_CONFIG_START_Q (0x00000003) +#define TX_CONFIG_EHP (0x00400000) +#define TX_CONFIG_CHP (0x00800000) +#define TX_CONFIG_RST (0x80000000) + +#define reg_TX_CONTROL(base) __REG32(base, 0x00000224) +#define TX_CONTROL_GO (0x00008000) +#define TX_CONTROL_MP (0x01000000) +#define TX_CONTROL_EAI (0x20000000) +#define TX_CONTROL_ABT (0x40000000) +#define TX_CONTROL_EII (0x80000000) + +#define reg_TX_STATUS(base) __REG32(base, 0x00000228) +#define TX_STATUS_QUEUE_USABLE (0x0000000f) +#define TX_STATUS_CURR_Q (0x00000300) +#define TX_STATUS_ACT (0x00008000) +#define TX_STATUS_QUEUE_IDLE (0x000f0000) +#define TX_STATUS_EOQ_PENDING (0x0f000000) + +#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c) +#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f) +#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00) +#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) +#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) + +#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230) + +#define reg_TX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000270) +#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) +#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000) +#define TX_DIAGNOSTIC_ADDR_AI (0x80000000) + +#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274) + +#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278) +#define TX_ERROR_STATUS (0x00000278) +#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010) +#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020) +#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040) +#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080) +#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000) +#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000) +#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000) + +#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280) +#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) +#define TX_QUEUE_0_CONFIG_BSWP (0x00000400) +#define TX_QUEUE_0_CONFIG_WSWP (0x00000800) +#define TX_QUEUE_0_CONFIG_AM (0x00004000) +#define TX_QUEUE_0_CONFIG_GVI (0x00008000) +#define TX_QUEUE_0_CONFIG_EEI (0x00010000) +#define TX_QUEUE_0_CONFIG_ELI (0x00020000) +#define TX_QUEUE_0_CONFIG_ENI (0x00040000) +#define TX_QUEUE_0_CONFIG_ESI (0x00080000) +#define TX_QUEUE_0_CONFIG_EDI (0x00100000) + +#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284) +#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) +#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) +#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) +#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) + +#define OCN_PORT_HLP 0 /* HLP Interface */ +#define OCN_PORT_PCI_X 1 /* PCI-X Interface */ +#define OCN_PORT_PROCESSOR_MASTER 2 /* Processor Interface (master) */ +#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */ +#define OCN_PORT_MEMORY 4 /* Memory Controller */ +#define OCN_PORT_DMA 5 /* DMA Controller */ +#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */ +#define OCN_PORT_PRINT 7 /* Print Engine Interface */ + +#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288) + +#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c) +#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000) + +#define reg_RX_CONFIG(base) __REG32(base, 0x00000320) +#define RX_CONFIG_DEF_Q (0x00000003) +#define RX_CONFIG_EMF (0x00000100) +#define RX_CONFIG_EUF (0x00000200) +#define RX_CONFIG_BFE (0x00000400) +#define RX_CONFIG_MFE (0x00000800) +#define RX_CONFIG_UFE (0x00001000) +#define RX_CONFIG_SE (0x00002000) +#define RX_CONFIG_ABF (0x00200000) +#define RX_CONFIG_APE (0x00400000) +#define RX_CONFIG_CHP (0x00800000) +#define RX_CONFIG_RST (0x80000000) + +#define reg_RX_CONTROL(base) __REG32(base, 0x00000324) +#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f) +#define GE_E0_RX_CONTROL_GO (0x00008000) +#define GE_E0_RX_CONTROL_EAI (0x20000000) +#define GE_E0_RX_CONTROL_ABT (0x40000000) +#define GE_E0_RX_CONTROL_EII (0x80000000) + +#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c) +#define RX_EXTENDED_STATUS (0x0000032c) +#define RX_EXTENDED_STATUS_EOQ (0x0000000f) +#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001) +#define RX_EXTENDED_STATUS_EOF (0x00000f00) +#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) +#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) + +#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330) + +#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370) +#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) +#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000) +#define RX_DIAGNOSTIC_ADDR_AI (0x80000000) + +#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374) + +#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380) +#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) +#define RX_QUEUE_0_CONFIG_BSWP (0x00000400) +#define RX_QUEUE_0_CONFIG_WSWP (0x00000800) +#define RX_QUEUE_0_CONFIG_AM (0x00004000) +#define RX_QUEUE_0_CONFIG_EEI (0x00010000) +#define RX_QUEUE_0_CONFIG_ELI (0x00020000) +#define RX_QUEUE_0_CONFIG_ENI (0x00040000) +#define RX_QUEUE_0_CONFIG_ESI (0x00080000) +#define RX_QUEUE_0_CONFIG_EDI (0x00100000) + +#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384) +#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) +#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) +#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) +#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) + +#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388) + +#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c) +#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000) + +/* + * PHY register definitions + */ +/* the first 15 PHY registers are standard. */ +#define PHY_CTRL_REG 0 /* Control Register */ +#define PHY_STATUS_REG 1 /* Status Regiser */ +#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */ +#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */ +#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */ +#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */ +#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */ + +/* + * PHY Register bit masks. + */ +#define PHY_CTRL_RESET (1 << 15) +#define PHY_CTRL_LOOPBACK (1 << 14) +#define PHY_CTRL_SPEED0 (1 << 13) +#define PHY_CTRL_AN_EN (1 << 12) +#define PHY_CTRL_PWR_DN (1 << 11) +#define PHY_CTRL_ISOLATE (1 << 10) +#define PHY_CTRL_RESTART_AN (1 << 9) +#define PHY_CTRL_FULL_DUPLEX (1 << 8) +#define PHY_CTRL_CT_EN (1 << 7) +#define PHY_CTRL_SPEED1 (1 << 6) + +#define PHY_STAT_100BASE_T4 (1 << 15) +#define PHY_STAT_100BASE_X_FD (1 << 14) +#define PHY_STAT_100BASE_X_HD (1 << 13) +#define PHY_STAT_10BASE_T_FD (1 << 12) +#define PHY_STAT_10BASE_T_HD (1 << 11) +#define PHY_STAT_100BASE_T2_FD (1 << 10) +#define PHY_STAT_100BASE_T2_HD (1 << 9) +#define PHY_STAT_EXT_STAT (1 << 8) +#define PHY_STAT_RESERVED (1 << 7) +#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */ +#define PHY_STAT_AN_COMPLETE (1 << 5) +#define PHY_STAT_REM_FAULT (1 << 4) +#define PHY_STAT_AN_CAP (1 << 3) +#define PHY_STAT_LINK_UP (1 << 2) +#define PHY_STAT_JABBER (1 << 1) +#define PHY_STAT_EXT_CAP (1 << 0) + +#define TBI_CONTROL_2 0x11 +#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001 +#define TBI_CONTROL_2_ENABLE_WRAP 0x0002 +#define TBI_CONTROL_2_G_MII_MODE 0x0010 +#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020 +#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100 +#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000 +#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000 +#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000 +#define TBI_CONTROL_2_SOFT_RESET 0x8000 + +/* marvel specific */ +#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */ +#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */ +#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */ + +/* + * MARVELL 88E1111 PHY register bit masks + */ +/* PHY Specific Status Register (MV1111_EXT_CTRL1_REG) */ + +#define SPEC_STAT_SPEED_MASK (3 << 14) +#define SPEC_STAT_FULL_DUP (1 << 13) +#define SPEC_STAT_PAGE_RCVD (1 << 12) +#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */ +#define SPEC_STAT_LINK_UP (1 << 10) +#define SPEC_STAT_CABLE_LEN_MASK (7 << 7) /* Cable Length (100/1000 modes only) */ +#define SPEC_STAT_MDIX (1 << 6) +#define SPEC_STAT_POLARITY (1 << 1) +#define SPEC_STAT_JABBER (1 << 0) + +#define SPEED_1000 (2 << 14) +#define SPEED_100 (1 << 14) +#define SPEED_10 (0 << 14) + +#define TBI_ADDR 0x1E /* Ten Bit Interface address */ + +/* negotiated link parameters */ +#define LINK_SPEED_UNKNOWN 0 +#define LINK_SPEED_10 1 +#define LINK_SPEED_100 2 +#define LINK_SPEED_1000 3 + +#define LINK_DUPLEX_UNKNOWN 0 +#define LINK_DUPLEX_HALF 1 +#define LINK_DUPLEX_FULL 2 + +static unsigned int phy_address[] = { 8, 9 }; + +#define vuint32 volatile u32 + +/* TX/RX buffer descriptors. MUST be cache line aligned in memory. (32 byte) + * This structure is accessed by the ethernet DMA engine which means it + * MUST be in LITTLE ENDIAN format */ +struct dma_descriptor { + vuint32 start_addr0; /* buffer address, least significant bytes. */ + vuint32 start_addr1; /* buffer address, most significant bytes. */ + vuint32 next_descr_addr0;/* next descriptor address, least significant bytes. Must be 64-bit aligned. */ + vuint32 next_descr_addr1;/* next descriptor address, most significant bytes. */ + vuint32 vlan_byte_count;/* VLAN tag(top 2 bytes) and byte countt (bottom 2 bytes). */ + vuint32 config_status; /* Configuration/Status. */ + vuint32 reserved1; /* reserved to make the descriptor cache line aligned. */ + vuint32 reserved2; /* reserved to make the descriptor cache line aligned. */ +}; + +/* last next descriptor address flag */ +#define DMA_DESCR_LAST (1 << 31) + +/* TX DMA descriptor config status bits */ +#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */ +#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */ +#define DMA_DESCR_TX_PFVLAN (1 << 2) +#define DMA_DESCR_TX_HUGE (1 << 3) +#define DMA_DESCR_TX_PAD (1 << 4) +#define DMA_DESCR_TX_CRC (1 << 5) +#define DMA_DESCR_TX_DESCR_INT (1 << 14) +#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000 +#define DMA_DESCR_TX_ONE_COLLISION (1 << 20) +#define DMA_DESCR_TX_LATE_COLLISION (1 << 24) +#define DMA_DESCR_TX_UNDERRUN (1 << 25) +#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26) +#define DMA_DESCR_TX_OK (1 << 30) +#define DMA_DESCR_TX_OWNER (1 << 31) + +/* RX DMA descriptor status bits */ +#define DMA_DESCR_RX_EOF (1 << 0) +#define DMA_DESCR_RX_SOF (1 << 1) +#define DMA_DESCR_RX_VTF (1 << 2) +#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3) +#define DMA_DESCR_RX_SHORT_FRAME (1 << 4) +#define DMA_DESCR_RX_HASH_MATCH (1 << 7) +#define DMA_DESCR_RX_BAD_FRAME (1 << 8) +#define DMA_DESCR_RX_OVERRUN (1 << 9) +#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11) +#define DMA_DESCR_RX_CRC_ERROR (1 << 12) +#define DMA_DESCR_RX_DESCR_INT (1 << 13) +#define DMA_DESCR_RX_OWNER (1 << 15) + +#define RX_BUFFER_SIZE PKTSIZE +#define NUM_RX_DESC PKTBUFSRX + +static struct dma_descriptor tx_descriptor __attribute__ ((aligned(32))); + +static struct dma_descriptor rx_descr_array[NUM_RX_DESC] + __attribute__ ((aligned(32))); + +static struct dma_descriptor *rx_descr_current; + +static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis); +static int tsi108_eth_send(struct eth_device *dev, + volatile void *packet, int length); +static int tsi108_eth_recv(struct eth_device *dev); +static void tsi108_eth_halt(struct eth_device *dev); +static unsigned int read_phy(unsigned int base, + unsigned int phy_addr, unsigned int phy_reg); +static void write_phy(unsigned int base, + unsigned int phy_addr, + unsigned int phy_reg, unsigned int phy_data); + +#if TSI108_ETH_DEBUG > 100 +/* + * print phy debug infomation + */ +static void dump_phy_regs(unsigned int phy_addr) +{ + int i; + + printf("PHY %d registers\n", phy_addr); + for (i = 0; i <= 30; i++) { + printf("%2d 0x%04x\n", i, read_phy(ETH_BASE, phy_addr, i)); + } + printf("\n"); + +} +#else +#define dump_phy_regs(base) do{}while(0) +#endif + +#if TSI108_ETH_DEBUG > 100 +/* + * print debug infomation + */ +static void tx_diag_regs(unsigned int base) +{ + int i; + unsigned long dummy; + + printf("TX diagnostics registers\n"); + reg_TX_DIAGNOSTIC_ADDR(base) = 0x00 | TX_DIAGNOSTIC_ADDR_AI; + udelay(1000); + dummy = reg_TX_DIAGNOSTIC_DATA(base); + for (i = 0x00; i <= 0x05; i++) { + udelay(1000); + printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); + } + reg_TX_DIAGNOSTIC_ADDR(base) = 0x40 | TX_DIAGNOSTIC_ADDR_AI; + udelay(1000); + dummy = reg_TX_DIAGNOSTIC_DATA(base); + for (i = 0x40; i <= 0x47; i++) { + udelay(1000); + printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); + } + printf("\n"); + +} +#else +#define tx_diag_regs(base) do{}while(0) +#endif + +#if TSI108_ETH_DEBUG > 100 +/* + * print debug infomation + */ +static void rx_diag_regs(unsigned int base) +{ + int i; + unsigned long dummy; + + printf("RX diagnostics registers\n"); + reg_RX_DIAGNOSTIC_ADDR(base) = 0x00 | RX_DIAGNOSTIC_ADDR_AI; + udelay(1000); + dummy = reg_RX_DIAGNOSTIC_DATA(base); + for (i = 0x00; i <= 0x05; i++) { + udelay(1000); + printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); + } + reg_RX_DIAGNOSTIC_ADDR(base) = 0x40 | RX_DIAGNOSTIC_ADDR_AI; + udelay(1000); + dummy = reg_RX_DIAGNOSTIC_DATA(base); + for (i = 0x08; i <= 0x0a; i++) { + udelay(1000); + printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); + } + printf("\n"); + +} +#else +#define rx_diag_regs(base) do{}while(0) +#endif + +#if TSI108_ETH_DEBUG > 100 +/* + * print debug infomation + */ +static void debug_mii_regs(unsigned int base) +{ + printf("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base)); + printf("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base)); + printf("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base)); + printf("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base)); + printf("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base)); + printf("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base)); + printf("\n"); + +} +#else +#define debug_mii_regs(base) do{}while(0) +#endif + +/* + * Wait until the phy bus is non-busy + */ +static void phy_wait(unsigned int base, unsigned int condition) +{ + int timeout; + + timeout = 0; + while (reg_MII_MGMT_INDICATORS(base) & condition) { + udelay(10); + if (++timeout > 10000) { + printf("ERROR: timeout waiting for phy bus (%d)\n", + condition); + break; + } + } +} + +/* + * read phy register + */ +static unsigned int read_phy(unsigned int base, + unsigned int phy_addr, unsigned int phy_reg) +{ + unsigned int value; + + phy_wait(base, MII_MGMT_INDICATORS_BUSY); + + reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg; + + /* Ensure that the Read Cycle bit is cleared prior to next read cycle */ + reg_MII_MGMT_COMMAND(base) = 0; + + /* start the read */ + reg_MII_MGMT_COMMAND(base) = MII_MGMT_COMMAND_READ_CYCLE; + + /* wait for the read to complete */ + phy_wait(base, + MII_MGMT_INDICATORS_NOT_VALID | MII_MGMT_INDICATORS_BUSY); + + value = reg_MII_MGMT_STATUS(base); + + reg_MII_MGMT_COMMAND(base) = 0; + + return value; +} + +/* + * write phy register + */ +static void write_phy(unsigned int base, + unsigned int phy_addr, + unsigned int phy_reg, unsigned int phy_data) +{ + phy_wait(base, MII_MGMT_INDICATORS_BUSY); + + reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg; + + /* Ensure that the Read Cycle bit is cleared prior to next cycle */ + reg_MII_MGMT_COMMAND(base) = 0; + + /* start the write */ + reg_MII_MGMT_CONTROL(base) = phy_data; +} + +/* + * configure the marvell 88e1111 phy + */ +static int marvell_88e_phy_config(struct eth_device *dev, int *speed, + int *duplex) +{ + unsigned long base; + unsigned long phy_addr; + unsigned int phy_status; + unsigned int phy_spec_status; + int timeout; + int phy_speed; + int phy_duplex; + unsigned int value; + + phy_speed = LINK_SPEED_UNKNOWN; + phy_duplex = LINK_DUPLEX_UNKNOWN; + + base = dev->iobase; + phy_addr = (unsigned long)dev->priv; + + /* Take the PHY out of reset. */ + write_phy(ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET); + + /* Wait for the reset process to complete. */ + udelay(10); + timeout = 0; + while ((phy_status = + read_phy(ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) { + udelay(10); + if (++timeout > 10000) { + printf("ERROR: timeout waiting for phy reset\n"); + break; + } + } + + /* TBI Configuration. */ + write_phy(base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE | + TBI_CONTROL_2_RECEIVE_CLOCK_SELECT); + /* Wait for the link to be established. */ + timeout = 0; + do { + udelay(20000); + phy_status = read_phy(ETH_BASE, phy_addr, PHY_STATUS_REG); + if (++timeout > 100) { + debug_lev(1, "ERROR: unable to establish link!!!\n"); + break; + } + } while ((phy_status & PHY_STAT_LINK_UP) == 0); + + if ((phy_status & PHY_STAT_LINK_UP) == 0) { + return 0; + } + + value = 0; + phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); + if (phy_spec_status & SPEC_STAT_RESOLVED) { + switch (phy_spec_status & SPEC_STAT_SPEED_MASK) { + case SPEED_1000: + phy_speed = LINK_SPEED_1000; + value |= PHY_CTRL_SPEED1; + break; + case SPEED_100: + phy_speed = LINK_SPEED_100; + value |= PHY_CTRL_SPEED0; + break; + case SPEED_10: + phy_speed = LINK_SPEED_10; + break; + } + if (phy_spec_status & SPEC_STAT_FULL_DUP) { + phy_duplex = LINK_DUPLEX_FULL; + value |= PHY_CTRL_FULL_DUPLEX; + } else { + phy_duplex = LINK_DUPLEX_HALF; + } + } + /* set TBI speed */ + write_phy(base, TBI_ADDR, PHY_CTRL_REG, value); + write_phy(base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060); + +#if TSI108_ETH_DEBUG > 0 + printf("%s link is up", dev->name); + phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); + if (phy_spec_status & SPEC_STAT_RESOLVED) { + switch (phy_speed) { + case LINK_SPEED_1000: + printf(", 1000 Mbps"); + break; + case LINK_SPEED_100: + printf(", 100 Mbps"); + break; + case LINK_SPEED_10: + printf(", 10 Mbps"); + break; + } + if (phy_duplex == LINK_DUPLEX_FULL) { + printf(", Full duplex"); + } else { + printf(", Half duplex"); + } + } + printf("\n"); +#endif + + dump_phy_regs(TBI_ADDR); + if (speed) { + *speed = phy_speed; + } + if (duplex) { + *duplex = phy_duplex; + } + + return 1; +} + +/* + * External interface + * + * register the tsi108 ethernet controllers with the multi-ethernet system + */ +int tsi108_eth_initialize(bd_t * bis) +{ + struct eth_device *dev; + int index; + + for (index = 0; index < CONFIG_TSI108_ETH_NUM_PORTS; index++) { + dev = (struct eth_device *)malloc(sizeof(struct eth_device)); + + sprintf(dev->name, "TSI108_eth%d", index); + + dev->iobase = ETH_BASE + (index * ETH_PORT_OFFSET); + dev->priv = (void *)(phy_address[index]); + dev->init = tsi108_eth_probe; + dev->halt = tsi108_eth_halt; + dev->send = tsi108_eth_send; + dev->recv = tsi108_eth_recv; + + eth_register(dev); + } + return index; +} + +/* + * probe for and initialize a single ethernet interface + */ +static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis) +{ + unsigned long base; + unsigned long value; + int index; + struct dma_descriptor *tx_descr; + struct dma_descriptor *rx_descr; + int speed; + int duplex; + + base = dev->iobase; + + reg_PORT_CONTROL(base) = PORT_CONTROL_STE | PORT_CONTROL_BPT; + + /* Bring DMA/FIFO out of reset. */ + reg_TX_CONFIG(base) = 0x00000000; + reg_RX_CONFIG(base) = 0x00000000; + + reg_TX_THRESHOLDS(base) = (192 << 16) | 192; + reg_RX_THRESHOLDS(base) = (192 << 16) | 112; + + /* Bring MAC out of reset. */ + reg_MAC_CONFIG_1(base) = 0x00000000; + + /* DMA MAC configuration. */ + reg_MAC_CONFIG_1(base) = + MAC_CONFIG_1_RX_ENABLE | MAC_CONFIG_1_TX_ENABLE; + + reg_MII_MGMT_CONFIG(base) = MII_MGMT_CONFIG_NO_PREAMBLE; + reg_MAXIMUM_FRAME_LENGTH(base) = RX_BUFFER_SIZE; + + /* Note: Early tsi108 manual did not have correct byte order + * for the station address.*/ + reg_STATION_ADDRESS_1(base) = (dev->enetaddr[5] << 24) | + (dev->enetaddr[4] << 16) | + (dev->enetaddr[3] << 8) | (dev->enetaddr[2] << 0); + + reg_STATION_ADDRESS_2(base) = (dev->enetaddr[1] << 24) | + (dev->enetaddr[0] << 16); + + if (marvell_88e_phy_config(dev, &speed, &duplex) == 0) { + return 0; + } + + value = + MAC_CONFIG_2_PREAMBLE_LENGTH(7) | MAC_CONFIG_2_PAD_CRC | + MAC_CONFIG_2_CRC_ENABLE; + if (speed == LINK_SPEED_1000) { + value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_BYTE); + } else { + value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_NIBBLE); + reg_PORT_CONTROL(base) |= PORT_CONTROL_SPD; + } + if (duplex == LINK_DUPLEX_FULL) { + value |= MAC_CONFIG_2_FULL_DUPLEX; + reg_PORT_CONTROL(base) &= ~PORT_CONTROL_BPT; + } else { + reg_PORT_CONTROL(base) |= PORT_CONTROL_BPT; + } + reg_MAC_CONFIG_2(base) = value; + + reg_RX_CONFIG(base) = RX_CONFIG_SE; + reg_RX_QUEUE_0_CONFIG(base) = OCN_PORT_MEMORY; + reg_RX_QUEUE_0_BUF_CONFIG(base) = OCN_PORT_MEMORY; + + /* initialize the RX DMA descriptors */ + rx_descr = &rx_descr_array[0]; + rx_descr_current = rx_descr; + for (index = 0; index < NUM_RX_DESC; index++) { + /* make sure the receive buffers are not in cache */ + invalidate_dcache_range((unsigned long)NetRxPackets[index], + (unsigned long)NetRxPackets[index] + + RX_BUFFER_SIZE); + rx_descr->start_addr0 = + cpu_to_le32((vuint32) NetRxPackets[index]); + rx_descr->start_addr1 = 0; + rx_descr->next_descr_addr0 = + cpu_to_le32((vuint32) (rx_descr + 1)); + rx_descr->next_descr_addr1 = 0; + rx_descr->vlan_byte_count = 0; + rx_descr->config_status = cpu_to_le32((RX_BUFFER_SIZE << 16) | + DMA_DESCR_RX_OWNER); + rx_descr++; + } + rx_descr--; + rx_descr->next_descr_addr0 = 0; + rx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST); + /* Push the descriptors to RAM so the ethernet DMA can see them */ + invalidate_dcache_range((unsigned long)rx_descr_array, + (unsigned long)rx_descr_array + + sizeof(rx_descr_array)); + + /* enable RX queue */ + reg_RX_CONTROL(base) = TX_CONTROL_GO | 0x01; + reg_RX_QUEUE_0_PTR_LOW(base) = (u32) rx_descr_current; + /* enable receive DMA */ + reg_RX_QUEUE_0_PTR_HIGH(base) = RX_QUEUE_0_PTR_HIGH_VALID; + + reg_TX_QUEUE_0_CONFIG(base) = OCN_PORT_MEMORY; + reg_TX_QUEUE_0_BUF_CONFIG(base) = OCN_PORT_MEMORY; + + /* initialize the TX DMA descriptor */ + tx_descr = &tx_descriptor; + + tx_descr->start_addr0 = 0; + tx_descr->start_addr1 = 0; + tx_descr->next_descr_addr0 = 0; + tx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST); + tx_descr->vlan_byte_count = 0; + tx_descr->config_status = cpu_to_le32(DMA_DESCR_TX_OK | + DMA_DESCR_TX_SOF | + DMA_DESCR_TX_EOF); + /* enable TX queue */ + reg_TX_CONTROL(base) = TX_CONTROL_GO | 0x01; + + return 1; +} + +/* + * send a packet + */ +static int tsi108_eth_send(struct eth_device *dev, + volatile void *packet, int length) +{ + unsigned long base; + int timeout; + struct dma_descriptor *tx_descr; + unsigned long status; + + base = dev->iobase; + tx_descr = &tx_descriptor; + + /* Wait until the last packet has been transmitted. */ + timeout = 0; + do { + /* make sure we see the changes made by the DMA engine */ + invalidate_dcache_range((unsigned long)tx_descr, + (unsigned long)tx_descr + + sizeof(struct dma_descriptor)); + + if (timeout != 0) { + udelay(15); + } + if (++timeout > 10000) { + tx_diag_regs(base); + debug_lev(1, + "ERROR: timeout waiting for last transmit packet to be sent\n"); + return 0; + } + } while (tx_descr->config_status & cpu_to_le32(DMA_DESCR_TX_OWNER)); + + status = le32_to_cpu(tx_descr->config_status); + if ((status & DMA_DESCR_TX_OK) == 0) { +#ifdef TX_PRINT_ERRORS + printf("TX packet error: 0x%08x\n %s%s%s%s\n", status, + status & DMA_DESCR_TX_OK ? "tx error, " : "", + status & DMA_DESCR_TX_RETRY_LIMIT ? + "retry limit reached, " : "", + status & DMA_DESCR_TX_UNDERRUN ? "underrun, " : "", + status & DMA_DESCR_TX_LATE_COLLISION ? "late collision, " + : ""); +#endif + } + + debug_lev(9, "sending packet %d\n", length); + tx_descr->start_addr0 = cpu_to_le32((vuint32) packet); + tx_descr->start_addr1 = 0; + tx_descr->next_descr_addr0 = 0; + tx_descr->next_descr_addr1 = cpu_to_le32(DMA_DESCR_LAST); + tx_descr->vlan_byte_count = cpu_to_le32(length); + tx_descr->config_status = cpu_to_le32(DMA_DESCR_TX_OWNER | + DMA_DESCR_TX_CRC | + DMA_DESCR_TX_PAD | + DMA_DESCR_TX_SOF | + DMA_DESCR_TX_EOF); + + invalidate_dcache_range((unsigned long)tx_descr, + (unsigned long)tx_descr + + sizeof(struct dma_descriptor)); + + invalidate_dcache_range((unsigned long)packet, + (unsigned long)packet + length); + + reg_TX_QUEUE_0_PTR_LOW(base) = (u32) tx_descr; + reg_TX_QUEUE_0_PTR_HIGH(base) = TX_QUEUE_0_PTR_HIGH_VALID; + + return length; +} + +/* + * Check for received packets and send them up the protocal stack + */ +static int tsi108_eth_recv(struct eth_device *dev) +{ + struct dma_descriptor *rx_descr; + unsigned long base; + int length = 0; + unsigned long status; + volatile uchar *buffer; + + base = dev->iobase; + + /* make sure we see the changes made by the DMA engine */ + invalidate_dcache_range((unsigned long)rx_descr_array, + (unsigned long)rx_descr_array + + sizeof(rx_descr_array)); + + /* process all of the received packets */ + rx_descr = rx_descr_current; + while ((rx_descr->config_status & cpu_to_le32(DMA_DESCR_RX_OWNER)) == 0) { + /* check for error */ + status = le32_to_cpu(rx_descr->config_status); + if (status & DMA_DESCR_RX_BAD_FRAME) { +#ifdef RX_PRINT_ERRORS + printf("RX packet error: 0x%08x\n %s%s%s%s%s%s\n", + status, + status & DMA_DESCR_RX_FRAME_IS_TYPE ? "too big, " + : "", + status & DMA_DESCR_RX_SHORT_FRAME ? "too short, " + : "", + status & DMA_DESCR_RX_BAD_FRAME ? "bad frame, " : + "", + status & DMA_DESCR_RX_OVERRUN ? "overrun, " : "", + status & DMA_DESCR_RX_MAX_FRAME_LEN ? + "max length, " : "", + status & DMA_DESCR_RX_CRC_ERROR ? "CRC error, " : + ""); +#endif + } else { + length = + le32_to_cpu(rx_descr->vlan_byte_count) & 0xFFFF; + + /*** process packet ***/ + buffer = + (volatile uchar + *)(le32_to_cpu(rx_descr->start_addr0)); + NetReceive(buffer, length); + + invalidate_dcache_range((unsigned long)buffer, + (unsigned long)buffer + + RX_BUFFER_SIZE); + } + /* Give this buffer back to the DMA engine */ + rx_descr->vlan_byte_count = 0; + rx_descr->config_status = cpu_to_le32((RX_BUFFER_SIZE << 16) | + DMA_DESCR_RX_OWNER); + /* move descriptor pointer forward */ + rx_descr = + (struct dma_descriptor + *)(le32_to_cpu(rx_descr->next_descr_addr0)); + if (rx_descr == 0) { + rx_descr = &rx_descr_array[0]; + } + } + /* remember where we are for next time */ + rx_descr_current = rx_descr; + + /* If the DMA engine has reached the end of the queue + * start over at the begining */ + if (reg_RX_EXTENDED_STATUS(base) & RX_EXTENDED_STATUS_EOQ_0) { + + reg_RX_EXTENDED_STATUS(base) = RX_EXTENDED_STATUS_EOQ_0; + reg_RX_QUEUE_0_PTR_LOW(base) = (u32) & rx_descr_array[0]; + reg_RX_QUEUE_0_PTR_HIGH(base) = RX_QUEUE_0_PTR_HIGH_VALID; + } + + return length; +} + +/* + * disable an ethernet interface + */ +static void tsi108_eth_halt(struct eth_device *dev) +{ + unsigned long base; + + base = dev->iobase; + + /* Put DMA/FIFO into reset state. */ + reg_TX_CONFIG(base) = TX_CONFIG_RST; + reg_RX_CONFIG(base) = RX_CONFIG_RST; + + /* Put MAC into reset state. */ + reg_MAC_CONFIG_1(base) = MAC_CONFIG_1_SOFT_RESET; +} + +#endif diff --git a/net/eth.c b/net/eth.c index e8ac251a4fe..c291f1908f7 100644 --- a/net/eth.c +++ b/net/eth.c @@ -52,6 +52,7 @@ extern int rtl8139_initialize(bd_t*); extern int rtl8169_initialize(bd_t*); extern int scc_initialize(bd_t*); extern int skge_initialize(bd_t*); +extern int tsi108_eth_initialize(bd_t*); extern int tsec_initialize(bd_t*, int, char *); extern int npe_initialize(bd_t *); @@ -245,6 +246,9 @@ int eth_initialize(bd_t *bis) #ifdef CONFIG_NS8382X ns8382x_initialize(bis); #endif +#if defined(CONFIG_TSI108_ETH) + tsi108_eth_initialize(bis); +#endif #if defined(CONFIG_RTL8139) rtl8139_initialize(bis); #endif -- cgit v1.3.1 From 9226e7d6f09b9a1ac074cd918c81225a4689bba8 Mon Sep 17 00:00:00 2001 From: roy zang Date: Thu, 2 Nov 2006 19:11:06 +0800 Subject: Tsi108 on chip pci controller support. If there is no pci card, the tsi108/109 pci configure read will cause a machine check exception to the processor. PCI error should also be cleared after the read. Signed-off-by: Alexandre Bounine Signed-off-by: Roy Zang --- drivers/tsi108_pci.c | 178 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 178 insertions(+) create mode 100644 drivers/tsi108_pci.c (limited to 'drivers') diff --git a/drivers/tsi108_pci.c b/drivers/tsi108_pci.c new file mode 100644 index 00000000000..f374ede6620 --- /dev/null +++ b/drivers/tsi108_pci.c @@ -0,0 +1,178 @@ +/* + * (C) Copyright 2004 Tundra Semiconductor Corp. + * Alex Bounine + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * PCI initialisation for the Tsi108 EMU board. + */ + +#include + +#ifdef CONFIG_TSI108_PCI + +#include +#include +#include +#include + +struct pci_controller local_hose; + +void tsi108_clear_pci_error(void) +{ + u32 err_stat, err_addr, pci_stat; + + /* + * Quietly clear errors signalled as result of PCI/X configuration read + * requests. + */ + /* Read PB Error Log Registers */ + err_stat = *(volatile u32 *)(CFG_TSI108_CSR_BASE + + TSI108_PB_REG_OFFSET + PB_ERRCS); + err_addr = *(volatile u32 *)(CFG_TSI108_CSR_BASE + + TSI108_PB_REG_OFFSET + PB_AERR); + if (err_stat & PB_ERRCS_ES) { + /* Clear PCI/X bus errors if applicable */ + if ((err_addr & 0xFF000000) == CFG_PCI_CFG_BASE) { + /* Clear error flag */ + *(u32 *) (CFG_TSI108_CSR_BASE + + TSI108_PB_REG_OFFSET + PB_ERRCS) = + PB_ERRCS_ES; + + /* Clear read error reported in PB_ISR */ + *(u32 *) (CFG_TSI108_CSR_BASE + + TSI108_PB_REG_OFFSET + PB_ISR) = + PB_ISR_PBS_RD_ERR; + + /* Clear errors reported by PCI CSR (Normally Master Abort) */ + pci_stat = *(volatile u32 *)(CFG_TSI108_CSR_BASE + + TSI108_PCI_REG_OFFSET + + PCI_CSR); + *(volatile u32 *)(CFG_TSI108_CSR_BASE + + TSI108_PCI_REG_OFFSET + PCI_CSR) = + pci_stat; + + *(volatile u32 *)(CFG_TSI108_CSR_BASE + + TSI108_PCI_REG_OFFSET + + PCI_IRP_STAT) = PCI_IRP_STAT_P_CSR; + } + } + + return; +} + +unsigned int __get_pci_config_dword(u32 addr) +{ + unsigned int retval; + + __asm__ __volatile__(" lwbrx %0,0,%1\n" + "1: eieio\n" + "2:\n" + ".section .fixup,\"ax\"\n" + "3: li %0,-1\n" + " b 2b\n" + ".section __ex_table,\"a\"\n" + " .align 2\n" + " .long 1b,3b\n" + ".text":"=r"(retval):"r"(addr)); + + return (retval); +} + +static int tsi108_read_config_dword(struct pci_controller *hose, + pci_dev_t dev, int offset, u32 * value) +{ + dev &= (CFG_PCI_CFG_SIZE - 1); + dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc)); + *value = __get_pci_config_dword(dev); + if (0xFFFFFFFF == *value) + tsi108_clear_pci_error(); + return 0; +} + +static int tsi108_write_config_dword(struct pci_controller *hose, + pci_dev_t dev, int offset, u32 value) +{ + dev &= (CFG_PCI_CFG_SIZE - 1); + dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc)); + + out_le32((volatile unsigned *)dev, value); + + return 0; +} + +void pci_init_board(void) +{ + struct pci_controller *hose = (struct pci_controller *)&local_hose; + + hose->first_busno = 0; + hose->last_busno = 0xff; + + pci_set_region(hose->regions + 0, + CFG_PCI_MEMORY_BUS, + CFG_PCI_MEMORY_PHYS, + CFG_PCI_MEMORY_SIZE, PCI_REGION_MEM | PCI_REGION_MEMORY); + + /* PCI memory space */ + pci_set_region(hose->regions + 1, + CFG_PCI_MEM_BUS, + CFG_PCI_MEM_PHYS, CFG_PCI_MEM_SIZE, PCI_REGION_MEM); + + /* PCI I/O space */ + pci_set_region(hose->regions + 2, + CFG_PCI_IO_BUS, + CFG_PCI_IO_PHYS, CFG_PCI_IO_SIZE, PCI_REGION_IO); + + hose->region_count = 3; + + pci_set_ops(hose, + pci_hose_read_config_byte_via_dword, + pci_hose_read_config_word_via_dword, + tsi108_read_config_dword, + pci_hose_write_config_byte_via_dword, + pci_hose_write_config_word_via_dword, + tsi108_write_config_dword); + + pci_register_hose(hose); + + hose->last_busno = pci_hose_scan(hose); + + debug("Done PCI initialization\n"); + return; +} + +#ifdef CONFIG_OF_FLAT_TREE +void +ft_pci_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + + p = (u32 *)ft_get_prop(blob, "/" OF_TSI "/pci@1000/bus-range", &len); + if (p != NULL) { + p[0] = local_hose.first_busno; + p[1] = local_hose.last_busno; + } + +} +#endif + +#endif /* CONFIG_TSI108_PCI */ -- cgit v1.3.1 From b825f158e449e1e9cf74c08e572955e122394c96 Mon Sep 17 00:00:00 2001 From: roy zang Date: Thu, 2 Nov 2006 19:12:31 +0800 Subject: Tsi108 on chip i2c support. The i2c Interface provides a master-only, serial interface that can be used for initializing Tsi108/Tsi109 registers from an EEPROM after a device reset. Signed-off-by: Alexandre Bounine Signed-off-by: Roy Zang --- drivers/tsi108_i2c.c | 300 +++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 300 insertions(+) create mode 100644 drivers/tsi108_i2c.c (limited to 'drivers') diff --git a/drivers/tsi108_i2c.c b/drivers/tsi108_i2c.c new file mode 100644 index 00000000000..08e5e3b4f55 --- /dev/null +++ b/drivers/tsi108_i2c.c @@ -0,0 +1,300 @@ +/* + * (C) Copyright 2004 Tundra Semiconductor Corp. + * Author: Alex Bounine + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#ifdef CONFIG_TSI108_I2C + +#include +#include + +#if (CONFIG_COMMANDS & CFG_CMD_I2C) + +#define I2C_DELAY 100000 +#undef DEBUG_I2C + +#ifdef DEBUG_I2C +#define DPRINT(x) printf(x) +#else +#define DPRINT(x) +#endif + +/* All functions assume that Tsi108 I2C block is the only master on the bus */ +/* I2C read helper function */ + +static int i2c_read_byte( + uint i2c_chan, /* I2C channel number: 0 - main, 1 - SDC SPD */ + uchar chip_addr,/* I2C device address on the bus */ + uint byte_addr, /* Byte address within I2C device */ + uchar * buffer /* pointer to data buffer */ + ) +{ + u32 temp; + u32 to_count = I2C_DELAY; + u32 op_status = TSI108_I2C_TIMEOUT_ERR; + u32 chan_offset = TSI108_I2C_OFFSET; + + DPRINT(("I2C read_byte() %d 0x%02x 0x%02x\n", + i2c_chan, chip_addr, byte_addr)); + + if (0 != i2c_chan) { + chan_offset = TSI108_I2C_SDRAM_OFFSET; + } + + /* Check if I2C operation is in progress */ + temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2); + + if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | + I2C_CNTRL2_START)) + ) { + /* Set device address and operation (read = 0) */ + temp = (byte_addr << 16) | ((chip_addr & 0x07) << 8) | + ((chip_addr >> 3) & 0x0F); + *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL1) = + temp; + + /* Issue the read command + * (at this moment all other parameters are 0 + * (size = 1 byte, lane = 0) + */ + + *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2) = + (I2C_CNTRL2_START); + + /* Wait until operation completed */ + do { + /* Read I2C operation status */ + temp = + *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + + I2C_CNTRL2); + + if (0 == + (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) + { + if (0 == + (temp & + (I2C_CNTRL2_I2C_CFGERR | + I2C_CNTRL2_I2C_TO_ERR)) + ) { + op_status = TSI108_I2C_SUCCESS; + + temp = *(u32 *) (CFG_TSI108_CSR_BASE + + chan_offset + + I2C_RD_DATA); + + *buffer = (u8) (temp & 0xFF); + } else { + /* report HW error */ + op_status = TSI108_I2C_IF_ERROR; + + DPRINT(("I2C HW error reported: 0x%02x\n", temp)); + } + + break; + } + } while (to_count--); + } else { + op_status = TSI108_I2C_IF_BUSY; + + DPRINT(("I2C Transaction start failed: 0x%02x\n", temp)); + } + + DPRINT(("I2C read_byte() status: 0x%02x\n", op_status)); + return op_status; +} + +/* + * I2C Read interface as defined in "include/i2c.h" : + * chip_addr: I2C chip address, range 0..127 + * (to read from SPD channel EEPROM use (0xD0 ... 0xD7) + * NOTE: The bit 7 in the chip_addr serves as a channel select. + * This hack is for enabling "isdram" command on Tsi108 boards + * without changes to common code. Used for I2C reads only. + * byte_addr: Memory or register address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Pointer to destination buffer for data to be read + * len: How many bytes to read + * + * Returns: 0 on success, not 0 on failure + */ + +int i2c_read(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, int len) +{ + u32 op_status = TSI108_I2C_PARAM_ERR; + u32 i2c_if = 0; + + /* Hack to support second (SPD) I2C controller (SPD EEPROM read only).*/ + if (0xD0 == (chip_addr & ~0x07)) { + i2c_if = 1; + chip_addr &= 0x7F; + } + /* Check for valid I2C address */ + if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) { + while (len--) { + op_status = + i2c_read_byte(i2c_if, chip_addr, byte_addr++, + buffer++); + + if (TSI108_I2C_SUCCESS != op_status) { + DPRINT(("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len)); + + break; + } + } + } + + DPRINT(("I2C read() status: 0x%02x\n", op_status)); + return op_status; +} + +/* I2C write helper function */ + +static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ + uint byte_addr, /* Byte address within I2C device */ + uchar * buffer /* pointer to data buffer */ + ) +{ + u32 temp; + u32 to_count = I2C_DELAY; + u32 op_status = TSI108_I2C_TIMEOUT_ERR; + + /* Check if I2C operation is in progress */ + temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); + + if (0 == + (temp & + (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) + { + /* Place data into the I2C Tx Register */ + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + + I2C_TX_DATA) = (u32) * buffer; + + /* Set device address and operation */ + temp = + I2C_CNTRL1_I2CWRITE | (byte_addr << 16) | + ((chip_addr & 0x07) << 8) | ((chip_addr >> 3) & 0x0F); + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + + I2C_CNTRL1) = temp; + + /* Issue the write command (at this moment all other parameters + * are 0 (size = 1 byte, lane = 0) + */ + + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + + I2C_CNTRL2) = (I2C_CNTRL2_START); + + op_status = TSI108_I2C_TIMEOUT_ERR; + + /* Wait until operation completed */ + do { + // Read I2C operation status + temp = + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + + I2C_CNTRL2); + + if (0 == + (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) + { + if (0 == + (temp & + (I2C_CNTRL2_I2C_CFGERR | + I2C_CNTRL2_I2C_TO_ERR))) { + op_status = TSI108_I2C_SUCCESS; + } else { + /* report detected HW error */ + op_status = TSI108_I2C_IF_ERROR; + + DPRINT(("I2C HW error reported: 0x%02x\n", temp)); + } + + break; + } + + } while (to_count--); + } else { + op_status = TSI108_I2C_IF_BUSY; + + DPRINT(("I2C Transaction start failed: 0x%02x\n", temp)); + } + + return op_status; +} + +/* + * I2C Write interface as defined in "include/i2c.h" : + * chip_addr: I2C chip address, range 0..127 + * byte_addr: Memory or register address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Pointer to data to be written + * len: How many bytes to write + * + * Returns: 0 on success, not 0 on failure + */ + +int i2c_write(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, + int len) +{ + u32 op_status = TSI108_I2C_PARAM_ERR; + + /* Check for valid I2C address */ + if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) { + while (len--) { + op_status = + i2c_write_byte(chip_addr, byte_addr++, buffer++); + + if (TSI108_I2C_SUCCESS != op_status) { + DPRINT(("I2C write_byte() failed: 0x%02x (%d left)\n", op_status, len)); + + break; + } + } + } + + return op_status; +} + +/* + * I2C interface function as defined in "include/i2c.h". + * Probe the given I2C chip address by reading single byte from offset 0. + * Returns 0 if a chip responded, not 0 on failure. + */ + +int i2c_probe(uchar chip) +{ + u32 tmp; + + /* + * Try to read the first location of the chip. + * The Tsi108 HW doesn't support sending just the chip address + * and checkong for an back. + */ + return i2c_read(chip, 0, 1, (char *)&tmp, 1); +} + +#endif /* (CONFIG_COMMANDS & CFG_CMD_I2C) */ +#endif /* CONFIG_TSI108_I2C */ -- cgit v1.3.1 From c1fbe4103a0d6c8957f912af902d705ba67836f2 Mon Sep 17 00:00:00 2001 From: roy zang Date: Thu, 2 Nov 2006 19:14:48 +0800 Subject: This patch comes from Yuli's posted patch on 8/8/2006 titled "CFI Driver Little-Endian write Issue". http://sourceforge.net/mailarchive/message.php?msg_id=36311999 If that patch applied, please discard this one. Until now , I do not see his patch is applied. So please apply this one. Signed-off-by: Yuli Barcohen Signed-off-by: Roy Zang --- drivers/cfi_flash.c | 32 ++++++++++++++++++++++++++------ 1 file changed, 26 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/cfi_flash.c b/drivers/cfi_flash.c index fd0a186828d..33a5822d90a 100644 --- a/drivers/cfi_flash.c +++ b/drivers/cfi_flash.c @@ -2,9 +2,12 @@ * (C) Copyright 2002-2004 * Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com * - * Copyright (C) 2003 Arabella Software Ltd. + * Copyright (C) 2003, 2006 Arabella Software Ltd. * Yuli Barcohen * Modified to work with AMD flashes + * Added support for byte lanes swap + * Added support for 32-bit chips consisting of two 16-bit devices + * (for example, S70GL256M00) * * Copyright (C) 2004 * Ed Okerson @@ -45,10 +48,13 @@ /* #define DEBUG */ #include + +#ifdef CFG_FLASH_CFI_DRIVER + +#include #include #include #include -#ifdef CFG_FLASH_CFI_DRIVER /* * This file implements a Common Flash Interface (CFI) driver for U-Boot. @@ -71,6 +77,10 @@ * Verify erase and program timeouts. */ +#if defined(__LITTLE_ENDIAN) && !defined(CFG_FLASH_CFI_SWAP) +#define CFG_FLASH_CFI_SWAP +#endif + #ifndef CFG_FLASH_BANKS_LIST #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #endif @@ -268,7 +278,7 @@ inline uchar flash_read_uchar (flash_info_t * info, uint offset) uchar *cp; cp = flash_make_addr (info, 0, offset); -#if defined(__LITTLE_ENDIAN) +#if defined(CFG_FLASH_CFI_SWAP) return (cp[0]); #else return (cp[info->portwidth - 1]); @@ -295,7 +305,7 @@ ushort flash_read_ushort (flash_info_t * info, flash_sect_t sect, uint offset) debug ("addr[%x] = 0x%x\n", x, addr[x]); } #endif -#if defined(__LITTLE_ENDIAN) +#if defined(CFG_FLASH_CFI_SWAP) retval = ((addr[(info->portwidth)] << 8) | addr[0]); #else retval = ((addr[(2 * info->portwidth) - 1] << 8) | @@ -327,7 +337,7 @@ ulong flash_read_long (flash_info_t * info, flash_sect_t sect, uint offset) debug ("addr[%x] = 0x%x\n", x, addr[x]); } #endif -#if defined(__LITTLE_ENDIAN) +#if defined(CFG_FLASH_CFI_SWAP) retval = (addr[0] << 16) | (addr[(info->portwidth)] << 24) | (addr[(2 * info->portwidth)]) | (addr[(3 * info->portwidth)] << 8); #else @@ -892,12 +902,22 @@ static void flash_make_cmd (flash_info_t * info, uchar cmd, void *cmdbuf) int i; uchar *cp = (uchar *) cmdbuf; -#if defined(__LITTLE_ENDIAN) +#if defined(CFG_FLASH_CFI_SWAP) for (i = info->portwidth; i > 0; i--) #else for (i = 1; i <= info->portwidth; i++) #endif *cp++ = (i & (info->chipwidth - 1)) ? '\0' : cmd; +#ifdef CFG_FLASH_CFI_2x16 + if ((info->portwidth == FLASH_CFI_32BIT) && (info->chipwidth == FLASH_CFI_BY16)) + { + uchar tmp; + cp = (uchar *) cmdbuf; + tmp = cp[1]; + cp[1] = cp[2]; + cp[2] = tmp; + } +#endif /* CFG_FLASH_CFI_2x16 */ } /* -- cgit v1.3.1 From ee311214e0d216f904feea269599d0934bf71f23 Mon Sep 17 00:00:00 2001 From: roy zang Date: Fri, 1 Dec 2006 11:47:36 +0800 Subject: Clean up the code according to codestyle: (1) remove some C++ comments. (2) remove trailing white space. (3) remove trailing empty line. (4) Indentation by table. (5) remove {} in one line condition. (6) add space before '(' in function call. Remove some weird printf () output. Add necessary comments. Modified Makefile to support building in a separate directory. --- Makefile | 2 +- board/mpc7448hpc2/Makefile | 20 +- board/mpc7448hpc2/asm_init.S | 1143 +++++++++++++++++++-------------------- board/mpc7448hpc2/mpc7448hpc2.c | 152 +++--- board/mpc7448hpc2/tsi108_init.c | 421 +++++++------- cpu/74xx_7xx/cpu.c | 16 +- cpu/74xx_7xx/speed.c | 82 +-- doc/README.mpc7448hpc2 | 206 ++++--- drivers/tsi108_eth.c | 835 ++++++++++++++-------------- drivers/tsi108_i2c.c | 60 +- drivers/tsi108_pci.c | 34 +- include/configs/mpc7448hpc2.h | 290 +++++----- include/tsi108.h | 280 +++++----- 13 files changed, 1747 insertions(+), 1794 deletions(-) (limited to 'drivers') diff --git a/Makefile b/Makefile index 531a257a67d..e781a6747d3 100644 --- a/Makefile +++ b/Makefile @@ -1722,7 +1722,7 @@ EVB64260_750CX_config: unconfig @$(MKCONFIG) EVB64260 ppc 74xx_7xx evb64260 mpc7448hpc2_config: unconfig - @./mkconfig $(@:_config=) ppc 74xx_7xx mpc7448hpc2 + @$(MKCONFIG) $(@:_config=) ppc 74xx_7xx mpc7448hpc2 P3G4_config: unconfig @$(MKCONFIG) $(@:_config=) ppc 74xx_7xx evb64260 diff --git a/board/mpc7448hpc2/Makefile b/board/mpc7448hpc2/Makefile index d5ed01f026a..e3d757d5dd1 100644 --- a/board/mpc7448hpc2/Makefile +++ b/board/mpc7448hpc2/Makefile @@ -23,26 +23,30 @@ include $(TOPDIR)/config.mk -LIB = lib$(BOARD).a +LIB = $(obj)lib$(BOARD).a -OBJS = $(BOARD).o tsi108_init.o +COBJS := $(BOARD).o tsi108_init.o +SOBJS := asm_init.o -SOBJS = asm_init.o +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) -$(LIB): .depend $(OBJS) $(SOBJS) - $(AR) crv $@ $(OBJS) $(SOBJS) +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) clean: rm -f $(SOBJS) $(OBJS) +.PHONY: distclean distclean: clean rm -f $(LIB) core *.bak .depend ######################################################################### -.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) - $(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ +# defines $(obj).depend target +include $(SRCTREE)/rules.mk -sinclude .depend +sinclude ($obj).depend ######################################################################### diff --git a/board/mpc7448hpc2/asm_init.S b/board/mpc7448hpc2/asm_init.S index 8c15a3d4979..a7a40a134c7 100644 --- a/board/mpc7448hpc2/asm_init.S +++ b/board/mpc7448hpc2/asm_init.S @@ -1,10 +1,10 @@ -/***************************************************************************** +/* * (C) Copyright 2004-05; Tundra Semiconductor Corp. - * + * * Added automatic detect of SDC settings * Copyright (c) 2005 Freescale Semiconductor, Inc. * Maintainer tie-fei.zang@freescale.com - * + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of @@ -19,9 +19,9 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA - ****************************************************************************/ + */ -/*---------------------------------------------------------------------------- +/* * FILENAME: asm_init.s * * Originator: Alex Bounine @@ -29,7 +29,7 @@ * DESCRIPTION: * Initialization code for the Tundra Tsi108 bridge chip * - *---------------------------------------------------------------------------*/ + */ #include #include @@ -40,15 +40,15 @@ #include -/*=========================================================================== +/* * Build Configuration Options */ -/* #define DISABLE_PBM disables usage of PB Master */ -/* #define SDC_HARDCODED_INIT config SDRAM controller with hardcoded values */ -/* #define SDC_AUTOPRECH_EN enable SDRAM auto precharge */ +/* #define DISABLE_PBM disables usage of PB Master */ +/* #define SDC_HARDCODED_INIT config SDRAM controller with hardcoded values */ +/* #define SDC_AUTOPRECH_EN enable SDRAM auto precharge */ -/* =========================================================================== +/* * Hardcoded SDC settings */ @@ -56,571 +56,543 @@ /* Micron MT9HTF6472AY-40EA1 : Unbuffered, 512MB, 400, CL3, Single Rank */ -#define VAL_SD_REFRESH (0x61A) -#define VAL_SD_TIMING (0x0308336b) -#define VAL_SD_D0_CTRL (0x07100021) /* auto-precharge disabled */ -#define VAL_SD_D0_BAR (0x0FE00000) /* 512MB @ 0x00000000 */ -#define VAL_SD_D1_CTRL (0x07100021) /* auto-precharge disabled */ -#define VAL_SD_D1_BAR (0x0FE00200) /* 512MB @ 0x20000000 */ +#define VAL_SD_REFRESH (0x61A) +#define VAL_SD_TIMING (0x0308336b) +#define VAL_SD_D0_CTRL (0x07100021) /* auto-precharge disabled */ +#define VAL_SD_D0_BAR (0x0FE00000) /* 512MB @ 0x00000000 */ +#define VAL_SD_D1_CTRL (0x07100021) /* auto-precharge disabled */ +#define VAL_SD_D1_BAR (0x0FE00200) /* 512MB @ 0x20000000 */ #endif /* SDC_HARDCODED_INIT */ -/*--------------------------------------------------------------------------- +/* CPU Configuration: CPU Address and Data Parity enables. #define CPU_AP #define CPU_DP +*/ -=========================================================================== - Macros - - !!! Attention !!! Macros LOAD_PTR, LOAD_U32 and LOAD_MEM defined below are - expected to work correctly for the CSR space within 32KB range. - - LOAD_PTR and LOAD_U32 - load specified register with a 32 bit constant. - These macros are absolutely identical except their names. This difference - is provided intentionally for better readable code. - -------------------------------------------------------------------------*/ +/* + * Macros + * !!! Attention !!! Macros LOAD_PTR, LOAD_U32 and LOAD_MEM defined below are + * expected to work correctly for the CSR space within 32KB range. + * + * LOAD_PTR and LOAD_U32 - load specified register with a 32 bit constant. + * These macros are absolutely identical except their names. This difference + * is provided intentionally for better readable code. + */ #define LOAD_PTR(reg,const32) \ - addis reg,r0,const32@h; ori reg,reg,const32@l + addis reg,r0,const32@h; ori reg,reg,const32@l #define LOAD_U32(reg,const32) \ - addis reg,r0,const32@h; ori reg,reg,const32@l + addis reg,r0,const32@h; ori reg,reg,const32@l -/* LOADMEM initializes a register with the contents of a specified 32-bit memory - location, usually a CSR value.*/ +/* LOADMEM initializes a register with the contents of a specified 32-bit + * memory location, usually a CSR value. + */ #define LOAD_MEM(reg,addr32) \ - addis reg,r0,addr32@ha; lwz reg,addr32@l(reg) + addis reg,r0,addr32@ha; lwz reg,addr32@l(reg) #ifndef SDC_HARDCODED_INIT sdc_clk_sync: /* MHz: 0,0,183,100,133,167,200,233 */ - .long 0,0, 6, 10, 8, 6, 5, 4 /* nSec */ + .long 0, 0, 6, 10, 8, 6, 5, 4 /* nSec */ #endif -/*=========================================================================== - board_asm_init() - early initialization function. Coded to be portable to - dual-CPU configuration. - Checks CPU number and performs board HW initialization if called for CPU0. - - Registers used: r3,r4,r5,r6,r19,r29 -=========================================================================== - ---------------------------------------------------------------------------- - NOTE: For dual-CPU configuration only CPU0 is allowed to configure Tsi108 - and the rest of the board. Current implementation demonstrates two - possible ways to identify CPU number: - - for MPC74xx platform: uses MSSCR0[ID] bit as defined in UM. - - for PPC750FX/GX boards: uses WHO_AM_I bit reported by Tsi108. ----------------------------------------------------------------------------*/ +/* + * board_asm_init() - early initialization function. Coded to be portable to + * dual-CPU configuration. + * Checks CPU number and performs board HW initialization if called for CPU0. + * Registers used: r3,r4,r5,r6,r19,r29 + * + * NOTE: For dual-CPU configuration only CPU0 is allowed to configure Tsi108 + * and the rest of the board. Current implementation demonstrates two + * possible ways to identify CPU number: + * - for MPC74xx platform: uses MSSCR0[ID] bit as defined in UM. + * - for PPC750FX/GX boards: uses WHO_AM_I bit reported by Tsi108. + */ - .globl board_asm_init + .globl board_asm_init board_asm_init: + mflr r19 /* Save LR to be able return later. */ + bl icache_enable /* Enable icache to reduce reads from flash. */ - mflr r19 /* Save LR to be able return later. */ - - bl icache_enable /* Enable icache to reduce reads from flash. */ +/* Initialize pointer to Tsi108 register space */ - /* Initialize pointer to Tsi108 register space - -------------------------------------------------------------------------*/ + LOAD_PTR(r29,CFG_TSI108_CSR_RST_BASE)/* r29 - pointer to tsi108 CSR space */ + ori r4,r29,TSI108_PB_REG_OFFSET - LOAD_PTR(r29,CFG_TSI108_CSR_RST_BASE)/* r29 - pointer to tsi108 CSR space */ - ori r4,r29,TSI108_PB_REG_OFFSET +/* Check Processor Version Number */ - /*------------------------------------------------------------------------- - Check Processor Version Number */ + mfspr r3, PVR + rlwinm r3,r3,16,16,23 /* get ((Processor Version Number) & 0xFF00) */ - mfspr r3, PVR - rlwinm r3,r3,16,16,23 /* get ((Processor Version Number) & 0xFF00) */ + cmpli 0,0,r3,0x8000 /* MPC74xx */ + bne cont_brd_init - cmpli 0,0,r3,0x8000 /* MPC74xx */ - bne cont_brd_init - - /* ------------------------------------------ - For MPC744x/5x enable extended BATs[4-7] - Sri: Set HIGH_BAT_EN and XBSEN, and SPD =1 - to disable prefetch - */ - - mfspr r5, HID0 - oris r5, r5, 0x0080 /* Set HID0[HIGH_BAT_EN] bit #8 */ - ori r5, r5, 0x0380 /* Set SPD,XBSEN,SGE bits #22,23,24 */ - mtspr HID0, r5 - isync - sync + /* + * For MPC744x/5x enable extended BATs[4-7] + * Sri: Set HIGH_BAT_EN and XBSEN, and SPD =1 + * to disable prefetch + */ - /* Adding code to disable external interventions in MPX bus mode */ - mfspr r3, 1014 - oris r3, r3, 0x0100 /* Set the EIDIS bit in MSSCR0: bit 7 */ - mtspr 1014, r3 - isync - sync + mfspr r5, HID0 + oris r5, r5, 0x0080 /* Set HID0[HIGH_BAT_EN] bit #8 */ + ori r5, r5, 0x0380 /* Set SPD,XBSEN,SGE bits #22,23,24 */ + mtspr HID0, r5 + isync + sync - /* Sri: code to enable FP unit */ - mfmsr r3 - ori r3, r3, 0x2000 - mtmsr r3 - isync - sync + /* Adding code to disable external interventions in MPX bus mode */ + mfspr r3, 1014 + oris r3, r3, 0x0100 /* Set the EIDIS bit in MSSCR0: bit 7 */ + mtspr 1014, r3 + isync + sync -#if(1) /* def CONFIG_DUAL_CPU - ------------------------------------------------------------------------- - For MPC74xx processor, use MSSCR0[ID] bit to identify CPU number. - */ + /* Sri: code to enable FP unit */ + mfmsr r3 + ori r3, r3, 0x2000 + mtmsr r3 + isync + sync - mfspr r3,1014 /* read MSSCR0 */ - rlwinm. r3,r3,27,31,31 /* get processor ID number */ - mtspr SPRN_PIR,r3 /* Save CPU ID */ - sync - bne init_done - b do_tsi108_init + /* def CONFIG_DUAL_CPU + * For MPC74xx processor, use MSSCR0[ID] bit to identify CPU number. + */ +#if(1) + mfspr r3,1014 /* read MSSCR0 */ + rlwinm. r3,r3,27,31,31 /* get processor ID number */ + mtspr SPRN_PIR,r3 /* Save CPU ID */ + sync + bne init_done + b do_tsi108_init cont_brd_init: - /* An alternative method of checking the processor number (in addition - to configuration using MSSCR0[ID] bit on MPC74xx). - Good for IBM PPC750FX/GX. - */ - - lwz r3,PB_BUS_MS_SELECT(r4) /* read PB_ID register */ - rlwinm. r3,r3,24,31,31 /* get processor ID number */ - - bne init_done + /* An alternative method of checking the processor number (in addition + * to configuration using MSSCR0[ID] bit on MPC74xx). + * Good for IBM PPC750FX/GX. + */ + lwz r3,PB_BUS_MS_SELECT(r4) /* read PB_ID register */ + rlwinm. r3,r3,24,31,31 /* get processor ID number */ + bne init_done #else cont_brd_init: #endif /* CONFIG_DUAL_CPU */ - /* Initialize Tsi108 chip - --------------------------------------------------------------------------- - */ + /* Initialize Tsi108 chip */ do_tsi108_init: - /*-------------------------------------------------------------------------- - Adjust HLP/Flash parameters. By default after reset the HLP port is set - to support slow devices. Better performance can be achived when an optimal - parameters are used for specific EPROM device. - NOTE: This should be performed ASAP for the emulation platform because - it has 5MHz HLP clocking. - */ + /* + * Adjust HLP/Flash parameters. By default after reset the HLP port is + * set to support slow devices. Better performance can be achived when + * an optimal parameters are used for specific EPROM device. + * NOTE: This should be performed ASAP for the emulation platform + * because it has 5MHz HLP clocking. + */ #ifdef CONFIG_TSI108EMU - ori r4,r29,TSI108_HLP_REG_OFFSET - LOAD_U32(r5,0x434422c0) - stw r5,0x08(r4) /* set HLP B0_CTRL0 */ - sync - LOAD_U32(r5,0xd0012000) - stw r5,0x0c(r4) /* set HLP B0_CTRL1 */ - sync + ori r4,r29,TSI108_HLP_REG_OFFSET + LOAD_U32(r5,0x434422c0) + stw r5,0x08(r4) /* set HLP B0_CTRL0 */ + sync + LOAD_U32(r5,0xd0012000) + stw r5,0x0c(r4) /* set HLP B0_CTRL1 */ + sync #endif - /* ------------------------------------------------------------------------- - * Initialize PB interface. - */ + /* Initialize PB interface. */ - ori r4,r29,TSI108_PB_REG_OFFSET + ori r4,r29,TSI108_PB_REG_OFFSET #if (CFG_TSI108_CSR_BASE != CFG_TSI108_CSR_RST_BASE) - /* Relocate (if required) Tsi108 registers. Set new value for PB_REG_BAR: - * Note we are in the 32-bit address mode. - */ - LOAD_U32(r5,(CFG_TSI108_CSR_BASE | 0x01)) /* value for PB_REG_BAR: BA + EN*/ - stw r5,PB_REG_BAR(r4) - andis. r29,r5,0xFFFF - sync - - ori r4,r29,TSI108_PB_REG_OFFSET + /* Relocate (if required) Tsi108 registers. Set new value for + * PB_REG_BAR: + * Note we are in the 32-bit address mode. + */ + LOAD_U32(r5,(CFG_TSI108_CSR_BASE | 0x01)) /* PB_REG_BAR: BA + EN */ + stw r5,PB_REG_BAR(r4) + andis. r29,r5,0xFFFF + sync + ori r4,r29,TSI108_PB_REG_OFFSET #endif - /* Set PB Slave configuration register */ + /* Set PB Slave configuration register */ -/* LOAD_U32(r5,0x000024C7) value for PB_SCR: TEA enabled,AACK delay = 7 */ - LOAD_U32(r5,0x00002481) /* value for PB_SCR: TEA enabled,AACK delay = 1 */ - lwz r3, PB_RSR(r4) /* get PB bus mode */ - xori r3,r3,0x0001 /* mask PB_BMODE: r3 -> (0 = 60X, 1 = MPX) */ - rlwimi r5,r3,14,17,17 /* for MPX: set DTI_MODE bit */ - stw r5,PB_SCR(r4) - sync + LOAD_U32(r5,0x00002481) /* PB_SCR: TEA enabled,AACK delay = 1 */ + lwz r3, PB_RSR(r4) /* get PB bus mode */ + xori r3,r3,0x0001 /* mask PB_BMODE: r3 -> (0 = 60X, 1 = MPX) */ + rlwimi r5,r3,14,17,17 /* for MPX: set DTI_MODE bit */ + stw r5,PB_SCR(r4) + sync - /* Configure PB Arbiter */ + /* Configure PB Arbiter */ - lwz r5,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */ - li r3, 0x00F0 /* ARB_PIPELINE_DEP mask */ + lwz r5,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */ + li r3, 0x00F0 /* ARB_PIPELINE_DEP mask */ #ifdef DISABLE_PBM - ori r3,r3,0x1000 /* add PBM_EN to clear (enabled by default) */ + ori r3,r3,0x1000 /* add PBM_EN to clear (enabled by default) */ #endif - andc r5,r5,r3 /* Clear the masked bit fields */ -/* ori r5,r5,0x0040 Set pipeline depth 4 - ori r5,r5,0x0080 Set pipeline depth 8 - ori r5,r5,0x0020 !!!avb Testing: set pipeline depth 2 */ - ori r5,r5,0x0001 - stw r5,PB_ARB_CTRL(r4) - -#if (0) /* currently using the default settings for PBM after reset */ - LOAD_U32(r5,0x) /* value for PB_MCR */ - stw r5,PB_MCR(r4) - sync - - LOAD_U32(r5,0x) /* value for PB_MCMD */ - stw r5,PB_MCMD(r4) - sync + andc r5,r5,r3 /* Clear the masked bit fields */ + ori r5,r5,0x0001 /* Set pipeline depth */ + stw r5,PB_ARB_CTRL(r4) + +#if (0) /* currently using the default settings for PBM after reset */ + LOAD_U32(r5,0x) /* value for PB_MCR */ + stw r5,PB_MCR(r4) + sync + + LOAD_U32(r5,0x) /* value for PB_MCMD */ + stw r5,PB_MCMD(r4) + sync #endif -/* Disable or enable PVT based on processor bus frequency - 1. Read CG_PWRUP_STATUS register field bits 18,17,16 - 2. See if the value is < or > 133mhz (18:16 = 100) - 3. If > enable PVT - */ + /* Disable or enable PVT based on processor bus frequency + * 1. Read CG_PWRUP_STATUS register field bits 18,17,16 + * 2. See if the value is < or > 133mhz (18:16 = 100) + * 3. If > enable PVT + */ - LOAD_U32(r3,0xC0002234) - lwz r3,0(r3) - rlwinm r3,r3,16,29,31 + LOAD_U32(r3,0xC0002234) + lwz r3,0(r3) + rlwinm r3,r3,16,29,31 - cmpi 0,0,r3,0x0004 - bgt sdc_init + cmpi 0,0,r3,0x0004 + bgt sdc_init #ifndef CONFIG_TSI108EMU - /* FIXME: Disable PB calibration control for any real Tsi108 board */ - li r5,0x0101 /* disable calibration control */ - stw r5,PB_PVT_CTRL2(r4) - sync + /* FIXME: Disable PB calibration control for any real Tsi108 board */ + li r5,0x0101 /* disable calibration control */ + stw r5,PB_PVT_CTRL2(r4) + sync #endif -/*--------------------------------------------------------------------------- - Initialize SDRAM controller. -----------------------------------------------------------------------------*/ + /* Initialize SDRAM controller. */ sdc_init: #ifndef SDC_HARDCODED_INIT - /* get SDC clock prior doing sdram controller autoconfig */ - ori r4,r29,TSI108_CLK_REG_OFFSET /* r4 - ptr to CG registers */ - lwz r3, CG_PWRUP_STATUS(r4) /* get CG configuration */ - rlwinm r3,r3,12,29,31 /* r3 - SD clk */ - lis r5,sdc_clk_sync@h - ori r5,r5,sdc_clk_sync@l - /* Sri: At this point check if r3 = 001. If yes, - * the memory frequency should be same as the - * MPX bus frequency - */ - cmpi 0,0,r3,0x0001 - bne get_nsec - lwz r6, CG_PWRUP_STATUS(r4) - rlwinm r6,r6,16,29,31 - mr r3,r6 + /* get SDC clock prior doing sdram controller autoconfig */ + ori r4,r29,TSI108_CLK_REG_OFFSET /* r4 - ptr to CG registers */ + lwz r3, CG_PWRUP_STATUS(r4) /* get CG configuration */ + rlwinm r3,r3,12,29,31 /* r3 - SD clk */ + lis r5,sdc_clk_sync@h + ori r5,r5,sdc_clk_sync@l + /* Sri: At this point check if r3 = 001. If yes, + * the memory frequency should be same as the + * MPX bus frequency + */ + cmpi 0,0,r3,0x0001 + bne get_nsec + lwz r6, CG_PWRUP_STATUS(r4) + rlwinm r6,r6,16,29,31 + mr r3,r6 get_nsec: - rlwinm r3,r3,2,0,31 - lwzx r9,r5,r3 /* get SD clk rate in nSec */ - /* ATTN: r9 will be used by SPD routine */ + rlwinm r3,r3,2,0,31 + lwzx r9,r5,r3 /* get SD clk rate in nSec */ + /* ATTN: r9 will be used by SPD routine */ #endif /* !SDC_HARDCODED_INIT */ - ori r4,r29,TSI108_SD_REG_OFFSET /* r4 - ptr to SDRAM registers */ + ori r4,r29,TSI108_SD_REG_OFFSET /* r4 - ptr to SDRAM registers */ - /* Initialize SDRAM controller. SDRAM Size = 512MB, One DIMM. */ + /* Initialize SDRAM controller. SDRAM Size = 512MB, One DIMM. */ - LOAD_U32(r5,0x00) - stw r5,SD_INT_ENABLE(r4) /* Ensure that interrupts are disabled */ + LOAD_U32(r5,0x00) + stw r5,SD_INT_ENABLE(r4) /* Ensure that interrupts are disabled */ #ifdef ENABLE_SDRAM_ECC - li r5, 0x01 + li r5, 0x01 #endif /* ENABLE_SDRAM_ECC */ - stw r5,SD_ECC_CTRL(r4) /* Enable/Disable ECC */ - sync + stw r5,SD_ECC_CTRL(r4) /* Enable/Disable ECC */ + sync #ifdef SDC_HARDCODED_INIT /* config sdram controller with hardcoded values */ - /* First read the CG_PWRUP_STATUS register to get the - memory speed from bits 22,21,20 */ - - LOAD_U32(r3,0xC0002234) - lwz r3,0(r3) - rlwinm r3,r3,12,29,31 + /* First read the CG_PWRUP_STATUS register to get the + * memory speed from bits 22,21,20 + */ - /* Now first check for 166, then 200, or default */ + LOAD_U32(r3,0xC0002234) + lwz r3,0(r3) + rlwinm r3,r3,12,29,31 - cmpi 0,0,r3,0x0005 - bne check_for_200mhz + /* Now first check for 166, then 200, or default */ - /* set values for 166 Mhz memory speed */ + cmpi 0,0,r3,0x0005 + bne check_for_200mhz - /* Set refresh rate and timing parameters */ - LOAD_U32(r5,0x00000515) - stw r5,SD_REFRESH(r4) - LOAD_U32(r5,0x03073368) - stw r5,SD_TIMING(r4) - sync + /* set values for 166 Mhz memory speed + * Set refresh rate and timing parameters + */ + LOAD_U32(r5,0x00000515) + stw r5,SD_REFRESH(r4) + LOAD_U32(r5,0x03073368) + stw r5,SD_TIMING(r4) + sync - /* Initialize DIMM0 control and BAR registers */ - LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ + /* Initialize DIMM0 control and BAR registers */ + LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D0_CTRL(r4) - LOAD_U32(r5,VAL_SD_D0_BAR) - stw r5,SD_D0_BAR(r4) - sync - - /* Initialize DIMM1 control and BAR registers - * (same as dimm 0, next 512MB, disabled) - */ - LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ + stw r5,SD_D0_CTRL(r4) + LOAD_U32(r5,VAL_SD_D0_BAR) + stw r5,SD_D0_BAR(r4) + sync + + /* Initialize DIMM1 control and BAR registers + * (same as dimm 0, next 512MB, disabled) + */ + LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D1_CTRL(r4) - LOAD_U32(r5,VAL_SD_D1_BAR) - stw r5,SD_D1_BAR(r4) - sync + stw r5,SD_D1_CTRL(r4) + LOAD_U32(r5,VAL_SD_D1_BAR) + stw r5,SD_D1_BAR(r4) + sync - b sdc_init_done + b sdc_init_done check_for_200mhz: - cmpi 0,0,r3,0x0006 - bne set_default_values + cmpi 0,0,r3,0x0006 + bne set_default_values - /* set values for 200Mhz memory speed */ - - /* Set refresh rate and timing parameters */ - LOAD_U32(r5,0x0000061a) - stw r5,SD_REFRESH(r4) - LOAD_U32(r5,0x03083348) - stw r5,SD_TIMING(r4) - sync + /* set values for 200Mhz memory speed + * Set refresh rate and timing parameters + */ + LOAD_U32(r5,0x0000061a) + stw r5,SD_REFRESH(r4) + LOAD_U32(r5,0x03083348) + stw r5,SD_TIMING(r4) + sync - /* Initialize DIMM0 control and BAR registers */ - LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ + /* Initialize DIMM0 control and BAR registers */ + LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D0_CTRL(r4) - LOAD_U32(r5,VAL_SD_D0_BAR) - stw r5,SD_D0_BAR(r4) - sync - - /* Initialize DIMM1 control and BAR registers - * (same as dimm 0, next 512MB, disabled) - */ - LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ + stw r5,SD_D0_CTRL(r4) + LOAD_U32(r5,VAL_SD_D0_BAR) + stw r5,SD_D0_BAR(r4) + sync + + /* Initialize DIMM1 control and BAR registers + * (same as dimm 0, next 512MB, disabled) + */ + LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D1_CTRL(r4) - LOAD_U32(r5,VAL_SD_D1_BAR) - stw r5,SD_D1_BAR(r4) - sync + stw r5,SD_D1_CTRL(r4) + LOAD_U32(r5,VAL_SD_D1_BAR) + stw r5,SD_D1_BAR(r4) + sync - b sdc_init_done + b sdc_init_done set_default_values: - /* Set refresh rate and timing parameters */ - LOAD_U32(r5,VAL_SD_REFRESH) - stw r5,SD_REFRESH(r4) - LOAD_U32(r5,VAL_SD_TIMING) - stw r5,SD_TIMING(r4) - sync + /* Set refresh rate and timing parameters */ + LOAD_U32(r5,VAL_SD_REFRESH) + stw r5,SD_REFRESH(r4) + LOAD_U32(r5,VAL_SD_TIMING) + stw r5,SD_TIMING(r4) + sync - /* Initialize DIMM0 control and BAR registers */ - LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ + /* Initialize DIMM0 control and BAR registers */ + LOAD_U32(r5,VAL_SD_D0_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D0_CTRL(r4) - LOAD_U32(r5,VAL_SD_D0_BAR) - stw r5,SD_D0_BAR(r4) - sync - - /* Initialize DIMM1 control and BAR registers - * (same as dimm 0, next 512MB, disabled) - */ - LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ + stw r5,SD_D0_CTRL(r4) + LOAD_U32(r5,VAL_SD_D0_BAR) + stw r5,SD_D0_BAR(r4) + sync + + /* Initialize DIMM1 control and BAR registers + * (same as dimm 0, next 512MB, disabled) + */ + LOAD_U32(r5,VAL_SD_D1_CTRL) /* auto-precharge disabled */ #ifdef SDC_AUTOPRECH_EN - oris r5,r5,0x0001 /* set auto precharge EN bit */ + oris r5,r5,0x0001 /* set auto precharge EN bit */ #endif - stw r5,SD_D1_CTRL(r4) - LOAD_U32(r5,VAL_SD_D1_BAR) - stw r5,SD_D1_BAR(r4) - sync - + stw r5,SD_D1_CTRL(r4) + LOAD_U32(r5,VAL_SD_D1_BAR) + stw r5,SD_D1_BAR(r4) + sync #else /* !SDC_HARDCODED_INIT */ - - bl tsi108_sdram_spd /* automatically detect SDC settings */ - + bl tsi108_sdram_spd /* automatically detect SDC settings */ #endif /* SDC_HARDCODED_INIT */ sdc_init_done: #ifdef DISABLE_PBM - LOAD_U32(r5,0x00000030) /* PB_EN + OCN_EN */ + LOAD_U32(r5,0x00000030) /* PB_EN + OCN_EN */ #else - LOAD_U32(r5,0x00000230) /* PB_EN + OCN_EN + PB/OCN=80/20 */ + LOAD_U32(r5,0x00000230) /* PB_EN + OCN_EN + PB/OCN=80/20 */ #endif /* DISABLE_PBM */ #ifdef CONFIG_TSI108EMU - oris r5,r5,0x0010 /* set EMULATION_MODE bit */ + oris r5,r5,0x0010 /* set EMULATION_MODE bit */ #endif - stw r5,SD_CTRL(r4) - eieio - sync + stw r5,SD_CTRL(r4) + eieio + sync - /* Enable SDRAM access */ + /* Enable SDRAM access */ - oris r5,r5,0x8000 /* start SDC: set SD_CTRL[ENABLE] bit */ - stw r5,SD_CTRL(r4) - sync + oris r5,r5,0x8000 /* start SDC: set SD_CTRL[ENABLE] bit */ + stw r5,SD_CTRL(r4) + sync wait_init_complete: - lwz r5,SD_STATUS(r4) - andi. r5,r5,0x0001 - beq wait_init_complete /* wait until SDRAM initialization is complete */ - -/*--------------------------------------------------------------------------- - Map SDRAM into the processor bus address space ----------------------------------------------------------------------------*/ + lwz r5,SD_STATUS(r4) + andi. r5,r5,0x0001 + /* wait until SDRAM initialization is complete */ + beq wait_init_complete - ori r4,r29,TSI108_PB_REG_OFFSET + /* Map SDRAM into the processor bus address space */ - /* Setup BARs associated with direct path PB<->SDRAM */ + ori r4,r29,TSI108_PB_REG_OFFSET - /* PB_SDRAM_BAR1: - provides a direct path to the main system memory (cacheable SDRAM) */ + /* Setup BARs associated with direct path PB<->SDRAM */ - LOAD_U32(r5, 0x00000011) /* BA=0,Size=512MB, ENable, No Addr.Translation */ - stw r5,PB_SDRAM_BAR1(r4) - sync + /* PB_SDRAM_BAR1: + * provides a direct path to the main system memory (cacheable SDRAM) + */ - /* Make sure that PB_SDRAM_BAR1 decoder is set - (to allow following immediate read from SDRAM) */ - lwz r5,PB_SDRAM_BAR1(r4) - sync + /* BA=0,Size=512MB, ENable, No Addr.Translation */ + LOAD_U32(r5, 0x00000011) + stw r5,PB_SDRAM_BAR1(r4) + sync - /* PB_SDRAM_BAR2: - provides non-cacheable alias (via the direct path) to main system memory. - Size = 512MB, ENable, Addr.Translation - ON, - BA = 0x0_40000000, TA = 0x0_00000000 */ + /* Make sure that PB_SDRAM_BAR1 decoder is set + * (to allow following immediate read from SDRAM) + */ + lwz r5,PB_SDRAM_BAR1(r4) + sync - LOAD_U32(r5, 0x40010011) - stw r5,PB_SDRAM_BAR2(r4) - sync + /* PB_SDRAM_BAR2: + * provides non-cacheable alias (via the direct path) to main + * system memory. + * Size = 512MB, ENable, Addr.Translation - ON, + * BA = 0x0_40000000, TA = 0x0_00000000 + */ - /* Make sure that PB_SDRAM_BAR2 decoder is set - (to allow following immediate read from SDRAM) */ - lwz r5,PB_SDRAM_BAR2(r4) - sync + LOAD_U32(r5, 0x40010011) + stw r5,PB_SDRAM_BAR2(r4) + sync + /* Make sure that PB_SDRAM_BAR2 decoder is set + * (to allow following immediate read from SDRAM) + */ + lwz r5,PB_SDRAM_BAR2(r4) + sync init_done: - /* All done. Restore LR and return. */ - mtlr r19 - blr + /* All done. Restore LR and return. */ + mtlr r19 + blr #if (0) -/*=========================================================================== - init_cpu1 - - This routine enables CPU1 on the dual-processor system. -===========================================================================*/ + /* + * init_cpu1 + * This routine enables CPU1 on the dual-processor system. + * Now there is only one processor in the system + */ - .global enable_cpu1 + .global enable_cpu1 enable_cpu1: - lis r3,Tsi108_Base@ha /* Get Grendel CSR Base Addr */ - addi r3,r3,Tsi108_Base@l - lwz r3,0(r3) /* R3 = CSR Base Addr */ - ori r4,r3,TSI108_PB_REG_OFFSET - lwz r3,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */ - ori r3,r3,0x0200 /* Set M1_EN bit */ - stw r3,PB_ARB_CTRL(r4) + lis r3,Tsi108_Base@ha /* Get Grendel CSR Base Addr */ + addi r3,r3,Tsi108_Base@l + lwz r3,0(r3) /* R3 = CSR Base Addr */ + ori r4,r3,TSI108_PB_REG_OFFSET + lwz r3,PB_ARB_CTRL(r4) /* Read PB Arbiter Control Register */ + ori r3,r3,0x0200 /* Set M1_EN bit */ + stw r3,PB_ARB_CTRL(r4) - blr + blr #endif -/*=========================================================================== - enable_EI - - Enable CPU core external interrupt -===========================================================================*/ + /* + * enable_EI + * Enable CPU core external interrupt + */ - .global enable_EI + .global enable_EI enable_EI: - mfmsr r3 - ori r3,r3,0x8000 /* set EE bit */ - mtmsr r3 - blr - -/*=========================================================================== - disable_EI + mfmsr r3 + ori r3,r3,0x8000 /* set EE bit */ + mtmsr r3 + blr - Disable CPU core external interrupt -===========================================================================*/ + /* + * disable_EI + * Disable CPU core external interrupt + */ - .global disable_EI + .global disable_EI disable_EI: - mfmsr r3 - li r4,-32768 /* aka "li r4,0x8000" */ - andc r3,r3,r4 /* clear EE bit */ - mtmsr r3 - blr + mfmsr r3 + li r4,-32768 /* aka "li r4,0x8000" */ + andc r3,r3,r4 /* clear EE bit */ + mtmsr r3 + blr #ifdef ENABLE_SDRAM_ECC -/*=========================================================================== - enable_ECC + /* enables SDRAM ECC */ - enables SDRAM ECC -===========================================================================*/ - - .global enable_ECC + .global enable_ECC enable_ECC: - ori r4,r29,TSI108_SD_REG_OFFSET - lwz r3,SD_ECC_CTRL(r4) /* Read SDRAM ECC Control Register */ - ori r3,r3,0x0001 /* Set ECC_EN bit */ - stw r3,SD_ECC_CTRL(r4) - blr - -/*=========================================================================== - clear_ECC_err + ori r4,r29,TSI108_SD_REG_OFFSET + lwz r3,SD_ECC_CTRL(r4) /* Read SDRAM ECC Control Register */ + ori r3,r3,0x0001 /* Set ECC_EN bit */ + stw r3,SD_ECC_CTRL(r4) + blr - Clears all pending SDRAM ECC errors - (normally after SDRAM scrubbing/initialization) -===========================================================================*/ + /* + * clear_ECC_err + * Clears all pending SDRAM ECC errors + * (normally after SDRAM scrubbing/initialization) + */ - .global clear_ECC_err + .global clear_ECC_err clear_ECC_err: - ori r4,r29,TSI108_SD_REG_OFFSET -/* lwz r3,SD_INT_STATUS(r4) Read SDRAM ECC Control Register */ - ori r3,r0,0x0030 /* ECC_UE_INT + ECC_CE_INT bits */ - stw r3,SD_INT_STATUS(r4) - blr + ori r4,r29,TSI108_SD_REG_OFFSET + ori r3,r0,0x0030 /* ECC_UE_INT + ECC_CE_INT bits */ + stw r3,SD_INT_STATUS(r4) + blr #endif /* ENABLE_SDRAM_ECC */ #ifndef SDC_HARDCODED_INIT -/******************************************************************** - * SDRAM SPD Support - */ - + /* SDRAM SPD Support */ #define SD_I2C_CTRL1 (0x400) #define SD_I2C_CTRL2 (0x404) #define SD_I2C_RD_DATA (0x408) -#define SD_I2C_WR_DATA (0x40C) +#define SD_I2C_WR_DATA (0x40C) -/* - * SDRAM SPD Support Macros - */ + /* + * SDRAM SPD Support Macros + */ #define SPD_DIMM0 (0x00000100) -#define SPD_DIMM1 (0x00000200) /* SPD_DIMM1 was 0x00000000 */ +#define SPD_DIMM1 (0x00000200) /* SPD_DIMM1 was 0x00000000 */ #define SPD_RDIMM (0x01) #define SPD_UDIMM (0x02) @@ -651,30 +623,30 @@ clear_ECC_err: * r10 - number of DDR slot where first SPD device is detected */ -#define READ_SPD(byte_num) \ - addis r3, 0, byte_num@l;\ - or r3, r3, r10;\ - ori r3, r3, 0x0A;\ - stw r3, SD_I2C_CTRL1(r4);\ - li r3, I2C_CNTRL2_START;\ - stw r3, SD_I2C_CTRL2(r4);\ - eieio;\ - sync;\ - li r3, 0x100;\ -1: ;\ - addic. r3, r3, -1;\ - bne 1b;\ -2: ;\ - lwz r5, SD_I2C_CTRL2(r4);\ - rlwinm. r3,r5,0,23,23;\ - bne 2b;\ - rlwinm. r3,r5,0,3,3;\ - lwz r3, SD_I2C_RD_DATA(r4) +#define READ_SPD(byte_num) \ + addis r3, 0, byte_num@l; \ + or r3, r3, r10; \ + ori r3, r3, 0x0A; \ + stw r3, SD_I2C_CTRL1(r4); \ + li r3, I2C_CNTRL2_START; \ + stw r3, SD_I2C_CTRL2(r4); \ + eieio; \ + sync; \ + li r3, 0x100; \ +1:; \ + addic. r3, r3, -1; \ + bne 1b; \ +2:; \ + lwz r5, SD_I2C_CTRL2(r4); \ + rlwinm. r3,r5,0,23,23; \ + bne 2b; \ + rlwinm. r3,r5,0,3,3; \ + lwz r3,SD_I2C_RD_DATA(r4) #define SPD_MIN_RFRSH (0x80) #define SPD_MAX_RFRSH (0x85) -refresh_rates: /* in nSec */ +refresh_rates: /* in nSec */ .long 15625 /* Normal (0x80) */ .long 3900 /* Reduced 0.25x (0x81) */ .long 7800 /* Reduced 0.5x (0x82) */ @@ -682,274 +654,265 @@ refresh_rates: /* in nSec */ .long 62500 /* Extended 4x (0x84) */ .long 125000 /* Extended 8x (0x85) */ -/*=========================================================================== +/* * tsi108_sdram_spd * * Inittializes SDRAM Controller using DDR2 DIMM Serial Presence Detect data * Uses registers: r4 - SDC base address (not changed) * r9 - SDC clocking period in nSec * Changes registers: r3,r5,r6,r7,r8,r10,r11 - *==========================================================================*/ + */ tsi108_sdram_spd: - li r10,SPD_DIMM0 + li r10,SPD_DIMM0 xor r11,r11,r11 /* DIMM Base Address: starts from 0 */ do_first_dimm: - /************************************** - * Program Refresh Rate Register - */ + /* Program Refresh Rate Register */ + + READ_SPD(12) /* get Refresh Rate */ + beq check_next_slot + li r5, ERR_RFRSH_RATE + cmpi 0,0,r3,SPD_MIN_RFRSH + ble spd_fail + cmpi 0,0,r3,SPD_MAX_RFRSH + bgt spd_fail + addi r3,r3,-SPD_MIN_RFRSH + rlwinm r3,r3,2,0,31 + lis r5,refresh_rates@h + ori r5,r5,refresh_rates@l + lwzx r5,r5,r3 /* get refresh rate in nSec */ + divwu r5,r5,r9 /* calculate # of SDC clocks */ + stw r5,SD_REFRESH(r4) /* Set refresh rate */ + sync - READ_SPD(12) /* get Refresh Rate */ - beq check_next_slot - li r5, ERR_RFRSH_RATE - cmpi 0,0,r3,SPD_MIN_RFRSH - ble spd_fail - cmpi 0,0,r3,SPD_MAX_RFRSH - bgt spd_fail - addi r3,r3,-SPD_MIN_RFRSH - rlwinm r3,r3,2,0,31 - lis r5,refresh_rates@h - ori r5,r5,refresh_rates@l - lwzx r5,r5,r3 /* get refresh rate in nSec */ - divwu r5,r5,r9 /* calculate # of SDC clocks */ - stw r5,SD_REFRESH(r4) /* Set refresh rate */ - sync - - /************************************** - * Program SD Timing Register - */ + /* Program SD Timing Register */ - li r7, 0 /* clear r7 prior parameter collection */ + li r7, 0 /* clear r7 prior parameter collection */ - READ_SPD(20) /* get DIMM type: Registered or Unbuffered */ + READ_SPD(20) /* get DIMM type: Registered or Unbuffered */ beq spd_read_fail - li r5, ERR_DIMM_TYPE - cmpi 0,0,r3,SPD_UDIMM - beq do_cl - cmpi 0,0,r3,SPD_RDIMM - bne spd_fail - oris r7,r7,0x1000 /* set SD_TIMING[DIMM_TYPE] bit */ + li r5, ERR_DIMM_TYPE + cmpi 0,0,r3,SPD_UDIMM + beq do_cl + cmpi 0,0,r3,SPD_RDIMM + bne spd_fail + oris r7,r7,0x1000 /* set SD_TIMING[DIMM_TYPE] bit */ do_cl: - READ_SPD(18) /* Get CAS Latency */ + READ_SPD(18) /* Get CAS Latency */ beq spd_read_fail - li r5,ERR_CL_VALUE - andi. r6,r3,SPD_CAS_3 - beq cl_4 - li r6,3 - b set_cl + li r5,ERR_CL_VALUE + andi. r6,r3,SPD_CAS_3 + beq cl_4 + li r6,3 + b set_cl cl_4: - andi. r6,r3,SPD_CAS_4 - beq cl_5 - li r6,4 - b set_cl + andi. r6,r3,SPD_CAS_4 + beq cl_5 + li r6,4 + b set_cl cl_5: - andi. r6,r3,SPD_CAS_5 - beq spd_fail - li r6,5 + andi. r6,r3,SPD_CAS_5 + beq spd_fail + li r6,5 set_cl: - rlwimi r7,r6,24,5,7 + rlwimi r7,r6,24,5,7 - READ_SPD(30) /* Get tRAS */ + READ_SPD(30) /* Get tRAS */ beq spd_read_fail - divwu r6,r3,r9 - mullw r8,r6,r9 - subf. r8,r8,r3 + divwu r6,r3,r9 + mullw r8,r6,r9 + subf. r8,r8,r3 beq set_tras - addi r6,r6,1 + addi r6,r6,1 set_tras: li r5,ERR_TRAS_FAIL - cmpi 0,0,r6,0x0F /* max supported value */ - bgt spd_fail - rlwimi r7,r6,16,12,15 + cmpi 0,0,r6,0x0F /* max supported value */ + bgt spd_fail + rlwimi r7,r6,16,12,15 READ_SPD(29) /* Get tRCD */ beq spd_read_fail - rlwinm r3,r3,30,2,31/* right shift tRCD by 2 bits as per DDR2 spec */ - divwu r6,r3,r9 - mullw r8,r6,r9 - subf. r8,r8,r3 + /* right shift tRCD by 2 bits as per DDR2 spec */ + rlwinm r3,r3,30,2,31 + divwu r6,r3,r9 + mullw r8,r6,r9 + subf. r8,r8,r3 beq set_trcd - addi r6,r6,1 + addi r6,r6,1 set_trcd: - li r5,ERR_TRCD_FAIL - cmpi 0,0,r6,0x07 /* max supported value */ - bgt spd_fail - rlwimi r7,r6,12,17,19 + li r5,ERR_TRCD_FAIL + cmpi 0,0,r6,0x07 /* max supported value */ + bgt spd_fail + rlwimi r7,r6,12,17,19 READ_SPD(27) /* Get tRP value */ beq spd_read_fail - rlwinm r3,r3,30,2,31 /* right shift tRP by 2 bits as per DDR2 spec */ - divwu r6,r3,r9 - mullw r8,r6,r9 - subf. r8,r8,r3 + rlwinm r3,r3,30,2,31 /* right shift tRP by 2 bits as per DDR2 spec */ + divwu r6,r3,r9 + mullw r8,r6,r9 + subf. r8,r8,r3 beq set_trp - addi r6,r6,1 + addi r6,r6,1 set_trp: - li r5,ERR_TRP_FAIL - cmpi 0,0,r6,0x07 /* max supported value */ - bgt spd_fail - rlwimi r7,r6,8,21,23 + li r5,ERR_TRP_FAIL + cmpi 0,0,r6,0x07 /* max supported value */ + bgt spd_fail + rlwimi r7,r6,8,21,23 READ_SPD(36) /* Get tWR value */ beq spd_read_fail - rlwinm r3,r3,30,2,31 /* right shift tWR by 2 bits as per DDR2 spec */ - divwu r6,r3,r9 - mullw r8,r6,r9 - subf. r8,r8,r3 + rlwinm r3,r3,30,2,31 /* right shift tWR by 2 bits as per DDR2 spec */ + divwu r6,r3,r9 + mullw r8,r6,r9 + subf. r8,r8,r3 beq set_twr - addi r6,r6,1 + addi r6,r6,1 set_twr: - addi r6,r6,-1 /* Tsi108 SDC always gives one extra clock */ - li r5,ERR_TWR_FAIL - cmpi 0,0,r6,0x07 /* max supported value */ - bgt spd_fail - rlwimi r7,r6,5,24,26 + addi r6,r6,-1 /* Tsi108 SDC always gives one extra clock */ + li r5,ERR_TWR_FAIL + cmpi 0,0,r6,0x07 /* max supported value */ + bgt spd_fail + rlwimi r7,r6,5,24,26 READ_SPD(42) /* Get tRFC */ beq spd_read_fail - li r5, ERR_TRFC_FAIL + li r5, ERR_TRFC_FAIL /* Tsi108 spec: tRFC=(tRFC + 1)/2 */ - addi r3,r3,1 - rlwinm. r3,r3,31,1,31 /* divide by 2 */ - beq spd_fail - divwu r6,r3,r9 - mullw r8,r6,r9 - subf. r8,r8,r3 + addi r3,r3,1 + rlwinm. r3,r3,31,1,31 /* divide by 2 */ + beq spd_fail + divwu r6,r3,r9 + mullw r8,r6,r9 + subf. r8,r8,r3 beq set_trfc - addi r6,r6,1 + addi r6,r6,1 set_trfc: - cmpi 0,0,r6,0x1F /* max supported value */ - bgt spd_fail - rlwimi r7,r6,0,27,31 + cmpi 0,0,r6,0x1F /* max supported value */ + bgt spd_fail + rlwimi r7,r6,0,27,31 stw r7,SD_TIMING(r4) sync - /*===================================================================== + /* * The following two registers are set on per-DIMM basis. * The SD_REFRESH and SD_TIMING settings are common for both DIMMS - *===================================================================== */ do_each_dimm: - /***************************************** - * Program SDRAM DIMM Control Register - */ + /* Program SDRAM DIMM Control Register */ - li r7, 0 /* clear r7 prior parameter collection */ + li r7, 0 /* clear r7 prior parameter collection */ READ_SPD(13) /* Get Primary SDRAM Width */ beq spd_read_fail - cmpi 0,0,r3,4 /* Check for 4-bit SDRAM */ - beq do_nbank - oris r7,r7,0x0010 /* Set MEM_WIDTH bit */ + cmpi 0,0,r3,4 /* Check for 4-bit SDRAM */ + beq do_nbank + oris r7,r7,0x0010 /* Set MEM_WIDTH bit */ do_nbank: READ_SPD(17) /* Get Number of banks on SDRAM device */ beq spd_read_fail /* Grendel only distinguish betw. 4 or 8-bank memory parts */ - li r5,ERR_UNKNOWN_PART /* non-supported memory part */ - cmpi 0,0,r3,4 - beq do_nrank - cmpi 0,0,r3,8 - bne spd_fail - ori r7,r7,0x1000 + li r5,ERR_UNKNOWN_PART /* non-supported memory part */ + cmpi 0,0,r3,4 + beq do_nrank + cmpi 0,0,r3,8 + bne spd_fail + ori r7,r7,0x1000 do_nrank: - READ_SPD(5) /* Get # of Ranks */ + READ_SPD(5) /* Get # of Ranks */ beq spd_read_fail - li r5,ERR_NRANK_INVALID - andi. r6,r3,0x7 /* Use bits [2..0] only */ - beq do_addr_mode - cmpi 0,0,r6,1 - bgt spd_fail - rlwimi r7,r6,8,23,23 + li r5,ERR_NRANK_INVALID + andi. r6,r3,0x7 /* Use bits [2..0] only */ + beq do_addr_mode + cmpi 0,0,r6,1 + bgt spd_fail + rlwimi r7,r6,8,23,23 do_addr_mode: - READ_SPD(4) /* Get # of Column Addresses */ + READ_SPD(4) /* Get # of Column Addresses */ beq spd_read_fail - li r5, ERR_ADDR_MODE - andi. r3,r3,0x0f /* cut off reserved bits */ - cmpi 0,0,r3,8 - ble spd_fail - cmpi 0,0,r3,15 - bgt spd_fail - addi r6,r3,-8 /* calculate ADDR_MODE parameter */ - rlwimi r7,r6,4,24,27 /* set ADDR_MODE field */ + li r5, ERR_ADDR_MODE + andi. r3,r3,0x0f /* cut off reserved bits */ + cmpi 0,0,r3,8 + ble spd_fail + cmpi 0,0,r3,15 + bgt spd_fail + addi r6,r3,-8 /* calculate ADDR_MODE parameter */ + rlwimi r7,r6,4,24,27 /* set ADDR_MODE field */ set_dimm_ctrl: #ifdef SDC_AUTOPRECH_EN - oris r7,r7,0x0001 /* set auto precharge EN bit */ + oris r7,r7,0x0001 /* set auto precharge EN bit */ #endif - ori r7,r7,1 /* set ENABLE bit */ - cmpi 0,0,r10,SPD_DIMM0 - bne 1f - stw r7,SD_D0_CTRL(r4) + ori r7,r7,1 /* set ENABLE bit */ + cmpi 0,0,r10,SPD_DIMM0 + bne 1f + stw r7,SD_D0_CTRL(r4) sync - b set_dimm_bar + b set_dimm_bar 1: - stw r7,SD_D1_CTRL(r4) + stw r7,SD_D1_CTRL(r4) sync - /******************************************** - * Program SDRAM DIMMx Base Address Register - */ + /* Program SDRAM DIMMx Base Address Register */ set_dimm_bar: READ_SPD(5) /* get # of Ranks */ beq spd_read_fail - andi.r7,r3,0x7 - addi r7,r7,1 - READ_SPD(31) /* Read DIMM rank density */ + andi. r7,r3,0x7 + addi r7,r7,1 + READ_SPD(31) /* Read DIMM rank density */ beq spd_read_fail - rlwinm r5,r3,27,29,31 - rlwinm r6,r3,3,24,28 - or r5,r6,r5 /* r5 = Normalized Rank Density byte */ - lis r8, 0x0080 /* 128MB >> 4 */ - mullw r8,r8,r5 /* r8 = (rank_size >> 4) */ - mullw r8,r8,r7 /* r8 = (DIMM_size >> 4) */ - neg r7,r8 - rlwinm r7,r7,28,4,31 - or r7,r7,r11 /* set ADDR field */ - rlwinm r8,r8,12,20,31 - add r11,r11,r8 /* set Base Addr for next DIMM */ - - cmpi 0,0,r10,SPD_DIMM0 - bne set_dimm1_size - stw r7,SD_D0_BAR(r4) - sync - li r10,SPD_DIMM1 + rlwinm r5,r3,27,29,31 + rlwinm r6,r3,3,24,28 + or r5,r6,r5 /* r5 = Normalized Rank Density byte */ + lis r8, 0x0080 /* 128MB >> 4 */ + mullw r8,r8,r5 /* r8 = (rank_size >> 4) */ + mullw r8,r8,r7 /* r8 = (DIMM_size >> 4) */ + neg r7,r8 + rlwinm r7,r7,28,4,31 + or r7,r7,r11 /* set ADDR field */ + rlwinm r8,r8,12,20,31 + add r11,r11,r8 /* set Base Addr for next DIMM */ + + cmpi 0,0,r10,SPD_DIMM0 + bne set_dimm1_size + stw r7,SD_D0_BAR(r4) + sync + li r10,SPD_DIMM1 READ_SPD(0) bne do_each_dimm b spd_done set_dimm1_size: - stw r7,SD_D1_BAR(r4) + stw r7,SD_D1_BAR(r4) sync spd_done: blr check_next_slot: - cmpi 0,0,r10,SPD_DIMM1 - beq spd_read_fail - li r10,SPD_DIMM1 - b do_first_dimm + cmpi 0,0,r10,SPD_DIMM1 + beq spd_read_fail + li r10,SPD_DIMM1 + b do_first_dimm spd_read_fail: ori r3,r0,0xdead - b err_hung + b err_hung spd_fail: li r3,0x0bad sync -err_hung: /* hang here for debugging */ - nop - nop - b err_hung +err_hung: /* hang here for debugging */ + nop + nop + b err_hung #endif /* !SDC_HARDCODED_INIT */ - diff --git a/board/mpc7448hpc2/mpc7448hpc2.c b/board/mpc7448hpc2/mpc7448hpc2.c index f90a75124a9..4d221e7a697 100644 --- a/board/mpc7448hpc2/mpc7448hpc2.c +++ b/board/mpc7448hpc2/mpc7448hpc2.c @@ -25,7 +25,7 @@ */ /* - * board support/init functions for the + * board support/init functions for the * Freescale MPC7448 HPC2 (High-Performance Computing 2 Platform). */ @@ -33,39 +33,38 @@ #include <74xx_7xx.h> #if defined(CONFIG_OF_FLAT_TREE) #include -extern void ft_cpu_setup(void *blob, bd_t *bd); +extern void ft_cpu_setup (void *blob, bd_t *bd); #endif #undef DEBUG -extern void flush_data_cache(void); -extern void invalidate_l1_instruction_cache(void); -extern void tsi108_init_f(void); +extern void flush_data_cache (void); +extern void invalidate_l1_instruction_cache (void); +extern void tsi108_init_f (void); -int display_mem_map(void); +int display_mem_map (void); -void after_reloc(ulong dest_addr) +void after_reloc (ulong dest_addr) { DECLARE_GLOBAL_DATA_PTR; /* * Jump to the main U-Boot board init code */ - board_init_r((gd_t *) gd, dest_addr); + board_init_r ((gd_t *) gd, dest_addr); /* NOTREACHED */ } /* * Check Board Identity: - * * report board type */ -int checkboard(void) +int checkboard (void) { int l_type = 0; - printf("BOARD: %s\n", CFG_BOARD_NAME); + printf ("BOARD: %s\n", CFG_BOARD_NAME); return (l_type); } @@ -75,19 +74,19 @@ int checkboard(void) * report calling processor number */ -int read_pid(void) +int read_pid (void) { return 0; /* we are on single CPU platform for a while */ } -long int dram_size(int board_type) +long int dram_size (int board_type) { return 0x20000000; /* 256M bytes */ } -long int initdram(int board_type) +long int initdram (int board_type) { - return dram_size(board_type); + return dram_size (board_type); } /* DRAM check routines copied from gw8260 */ @@ -114,11 +113,11 @@ long int initdram(int board_type) /* May cloober fr0. */ /* */ /*********************************************************************/ -static void move64(unsigned long long *src, unsigned long long *dest) +static void move64 (unsigned long long *src, unsigned long long *dest) { - asm("lfd 0, 0(3)\n\t" /* fpr0 = *scr */ - "stfd 0, 0(4)" /* *dest = fpr0 */ - : : :"fr0"); /* Clobbers fr0 */ + asm ("lfd 0, 0(3)\n\t" /* fpr0 = *scr */ + "stfd 0, 0(4)" /* *dest = fpr0 */ + : : :"fr0"); /* Clobbers fr0 */ return; } @@ -183,28 +182,28 @@ unsigned long long pattern[] = { /* Assumes only one one SDRAM bank */ /* */ /*********************************************************************/ -int mem_test_data(void) +int mem_test_data (void) { unsigned long long *pmem = (unsigned long long *)CFG_MEMTEST_START; unsigned long long temp64; - int num_patterns = sizeof(pattern) / sizeof(pattern[0]); + int num_patterns = sizeof (pattern) / sizeof (pattern[0]); int i; unsigned int hi, lo; for (i = 0; i < num_patterns; i++) { - move64(&(pattern[i]), pmem); - move64(pmem, &temp64); + move64 (&(pattern[i]), pmem); + move64 (pmem, &temp64); - /* hi = (temp64>>32) & 0xffffffff; */ - /* lo = temp64 & 0xffffffff; */ - /* printf("\ntemp64 = 0x%08x%08x", hi, lo); */ + /* hi = (temp64>>32) & 0xffffffff; */ + /* lo = temp64 & 0xffffffff; */ + /* printf ("\ntemp64 = 0x%08x%08x", hi, lo); */ hi = (pattern[i] >> 32) & 0xffffffff; lo = pattern[i] & 0xffffffff; - /* printf("\npattern[%d] = 0x%08x%08x", i, hi, lo); */ + /* printf ("\npattern[%d] = 0x%08x%08x", i, hi, lo); */ if (temp64 != pattern[i]) { - printf("\n Data Test Failed, pattern 0x%08x%08x", + printf ("\n Data Test Failed, pattern 0x%08x%08x", hi, lo); return 1; } @@ -236,7 +235,7 @@ int mem_test_data(void) /* */ /* */ /*********************************************************************/ -int mem_test_address(void) +int mem_test_address (void) { volatile unsigned int *pmem = (volatile unsigned int *)CFG_MEMTEST_START; @@ -251,13 +250,13 @@ int mem_test_address(void) /* verify each loaction */ for (i = 0; i < size; i++) { if (pmem[i] != i) { - printf("\n Address Test Failed at 0x%x", i); + printf ("\n Address Test Failed at 0x%x", i); return 1; } } return 0; } -#endif /* CFG_DRAM_TEST_ADDRESS */ +#endif /* CFG_DRAM_TEST_ADDRESS */ #if defined (CFG_DRAM_TEST_WALK) /*********************************************************************/ @@ -287,7 +286,7 @@ int mem_test_address(void) /* */ /* */ /*********************************************************************/ -int mem_march(volatile unsigned long long *base, +int mem_march (volatile unsigned long long *base, unsigned int size, unsigned long long rmask, unsigned long long wmask, short read, short write) @@ -299,14 +298,14 @@ int mem_march(volatile unsigned long long *base, for (i = 0; i < size; i++) { if (read != 0) { /* temp = base[i]; */ - move64((unsigned long long *)&(base[i]), &temp); + move64 ((unsigned long long *)&(base[i]), &temp); if (rmask != temp) { hitemp = (temp >> 32) & 0xffffffff; lotemp = temp & 0xffffffff; himask = (rmask >> 32) & 0xffffffff; lomask = rmask & 0xffffffff; - printf("\n Walking one's test failed: \ + printf ("\n Walking one's test failed: \ address = 0x%08x," "\n\texpected \ 0x%08x%08x, found 0x%08x%08x", i << 3,\ himask, lomask, hitemp, lotemp); @@ -315,12 +314,12 @@ int mem_march(volatile unsigned long long *base, } if (write != 0) { /* base[i] = wmask; */ - move64(&wmask, (unsigned long long *)&(base[i])); + move64 (&wmask, (unsigned long long *)&(base[i])); } } return 0; } -#endif /* CFG_DRAM_TEST_WALK */ +#endif /* CFG_DRAM_TEST_WALK */ /*********************************************************************/ /* NAME: mem_test_walk() - a simple walking ones test */ @@ -348,7 +347,7 @@ int mem_march(volatile unsigned long long *base, /* */ /* */ /*********************************************************************/ -int mem_test_walk(void) +int mem_test_walk (void) { unsigned long long mask; volatile unsigned long long *pmem = @@ -359,32 +358,31 @@ int mem_test_walk(void) mask = 0x01; - printf("Initial Pass"); - mem_march(pmem, size, 0x0, 0x1, 0, 1); + printf ("Initial Pass"); + mem_march (pmem, size, 0x0, 0x1, 0, 1); - printf("\b\b\b\b\b\b\b\b\b\b\b\b"); - printf(" "); - printf(" "); - printf("\b\b\b\b\b\b\b\b\b\b\b\b"); + printf ("\b\b\b\b\b\b\b\b\b\b\b\b"); + printf (" "); + printf (" "); + printf ("\b\b\b\b\b\b\b\b\b\b\b\b"); for (i = 0; i < 63; i++) { - printf("Pass %2d", i + 2); - if (mem_march(pmem, size, mask, mask << 1, 1, 1) != 0) { - /*printf("mask: 0x%x, pass: %d, ", mask, i); */ + printf ("Pass %2d", i + 2); + if (mem_march(pmem, size, mask, mask << 1, 1, 1) != 0) + /*printf ("mask: 0x%x, pass: %d, ", mask, i); */ return 1; - } mask = mask << 1; - printf("\b\b\b\b\b\b\b"); + printf ("\b\b\b\b\b\b\b"); } - printf("Last Pass"); + printf ("Last Pass"); if (mem_march(pmem, size, 0, mask, 0, 1) != 0) { - /* printf("mask: 0x%x", mask); */ + /* printf ("mask: 0x%x", mask); */ return 1; } - printf("\b\b\b\b\b\b\b\b\b"); - printf(" "); - printf("\b\b\b\b\b\b\b\b\b"); + printf ("\b\b\b\b\b\b\b\b\b"); + printf (" "); + printf ("\b\b\b\b\b\b\b\b\b"); return 0; } @@ -412,60 +410,58 @@ int mem_test_walk(void) /* */ /* */ /*********************************************************************/ -int testdram(void) +int testdram (void) { char *s; int rundata, runaddress, runwalk; - s = getenv("testdramdata"); + s = getenv ("testdramdata"); rundata = (s && (*s == 'y')) ? 1 : 0; - s = getenv("testdramaddress"); + s = getenv ("testdramaddress"); runaddress = (s && (*s == 'y')) ? 1 : 0; - s = getenv("testdramwalk"); + s = getenv ("testdramwalk"); runwalk = (s && (*s == 'y')) ? 1 : 0; /* rundata = 1; */ /* runaddress = 0; */ /* runwalk = 0; */ - if ((rundata == 1) || (runaddress == 1) || (runwalk == 1)) { - printf("Testing RAM from 0x%08x to 0x%08x ... \ + if ((rundata == 1) || (runaddress == 1) || (runwalk == 1)) + printf ("Testing RAM from 0x%08x to 0x%08x ... \ (don't panic... that will take a moment !!!!)\n", \ CFG_MEMTEST_START, CFG_MEMTEST_END); - } #ifdef CFG_DRAM_TEST_DATA if (rundata == 1) { - printf("Test DATA ... "); + printf ("Test DATA ... "); if (mem_test_data () == 1) { - printf("failed \n"); + printf ("failed \n"); return 1; } else - printf("ok \n"); + printf ("ok \n"); } #endif #ifdef CFG_DRAM_TEST_ADDRESS if (runaddress == 1) { - printf("Test ADDRESS ... "); + printf ("Test ADDRESS ... "); if (mem_test_address () == 1) { - printf("failed \n"); + printf ("failed \n"); return 1; } else - printf("ok \n"); + printf ("ok \n"); } #endif #ifdef CFG_DRAM_TEST_WALK if (runwalk == 1) { - printf("Test WALKING ONEs ... "); - if (mem_test_walk() == 1) { - printf("failed \n"); + printf ("Test WALKING ONEs ... "); + if (mem_test_walk () == 1) { + printf ("failed \n"); return 1; } else - printf("ok \n"); + printf ("ok \n"); } #endif - if ((rundata == 1) || (runaddress == 1) || (runwalk == 1)) { - printf("passed\n"); - } + if ((rundata == 1) || (runaddress == 1) || (runwalk == 1)) + printf ("passed\n"); return 0; } @@ -473,17 +469,17 @@ int testdram(void) #if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) void -ft_board_setup(void *blob, bd_t *bd) +ft_board_setup (void *blob, bd_t *bd) { u32 *p; int len; - ft_cpu_setup(blob, bd); + ft_cpu_setup (blob, bd); - p = ft_get_prop(blob, "/memory/reg", &len); + p = ft_get_prop (blob, "/memory/reg", &len); if (p != NULL) { - *p++ = cpu_to_be32(bd->bi_memstart); - *p = cpu_to_be32(bd->bi_memsize); + *p++ = cpu_to_be32 (bd->bi_memstart); + *p = cpu_to_be32 (bd->bi_memsize); } } #endif diff --git a/board/mpc7448hpc2/tsi108_init.c b/board/mpc7448hpc2/tsi108_init.c index 6f517f5a2ed..fdb53653d14 100644 --- a/board/mpc7448hpc2/tsi108_init.c +++ b/board/mpc7448hpc2/tsi108_init.c @@ -1,6 +1,6 @@ /***************************************************************************** * (C) Copyright 2003; Tundra Semiconductor Corp. - * + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of @@ -33,7 +33,7 @@ #include #include -extern void mpicInit(int verbose); +extern void mpicInit (int verbose); /* * Configuration Options @@ -118,11 +118,11 @@ static PLL_CTRL_SET pll0_config[8] = { static int pb_clk_sel[8] = { 0, 0, 183, 100, 133, 167, 200, 233 }; /* - * get_board_bus_clk() + * get_board_bus_clk () * * returns the bus clock in Hz. */ -unsigned long get_board_bus_clk(void) +unsigned long get_board_bus_clk (void) { ulong i; @@ -134,37 +134,38 @@ unsigned long get_board_bus_clk(void) } /* - * board_early_init_f() + * board_early_init_f () * * board-specific initialization executed from flash */ -int board_early_init_f(void) +int board_early_init_f (void) { DECLARE_GLOBAL_DATA_PTR; ulong i; gd->mem_clk = 0; - i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS); - i = (i >> 20) & 0x07; + i = in32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + + CG_PWRUP_STATUS); + i = (i >> 20) & 0x07; /* value of SW4[4:7] */ switch (i) { - case 0: - printf("Using external clock\n"); + case 0: /* external clock */ + printf ("Using external clock\n"); break; - case 1: + case 1: /* system clock */ gd->mem_clk = gd->bus_clk; break; - case 4: - case 5: - case 6: + case 4: /* 133 MHz */ + case 5: /* 166 MHz */ + case 6: /* 200 MHz */ gd->mem_clk = pb_clk_sel[i] * 1000000; break; default: - printf("Invalid DDR2 clock setting\n"); + printf ("Invalid DDR2 clock setting\n"); return -1; } - printf("BUS! %d MHz\n", get_board_bus_clk() / 1000000); - printf("MEM! %d MHz\n", gd->mem_clk / 1000000); + printf ("BUS: %d MHz\n", get_board_bus_clk() / 1000000); + printf ("MEM: %d MHz\n", gd->mem_clk / 1000000); return 0; } @@ -173,175 +174,174 @@ int board_early_init_f(void) * relocation. Contains code that cannot be executed from flash. */ -int board_early_init_r(void) +int board_early_init_r (void) { ulong temp, i; ulong reg_val; volatile ulong *reg_ptr; reg_ptr = - (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900); + (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900); for (i = 0; i < 32; i++) { *reg_ptr++ = 0x00000201; /* SWAP ENABLED */ *reg_ptr++ = 0x00; } - __asm__ __volatile__("eieio"); - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("eieio"); + __asm__ __volatile__ ("sync"); /* Setup PB_OCN_BAR2: size 256B + ENable @ 0x0_80000000 */ - out32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2, - 0x80000001); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2, + 0x80000001); + __asm__ __volatile__ ("sync"); /* Make sure that OCN_BAR2 decoder is set (to allow following immediate - * read from SDRAM) + * read from SDRAM) */ temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR2); - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("sync"); /* * Remap PB_OCN_BAR1 to accomodate PCI-bus aperture and EPROM into the * processor bus address space. Immediately after reset LUT and address * translation are disabled for this BAR. Now we have to initialize LUT * and switch from the BOOT mode to the normal operation mode. - * + * * The aperture defined by PB_OCN_BAR1 startes at address 0xE0000000 - * and covers 512MB of address space. To allow larger aperture we also + * and covers 512MB of address space. To allow larger aperture we also * have to relocate register window of Tsi108 * - * Initialize LUT (32-entries) prior switching PB_OCN_BAR1 from BOOT + * Initialize LUT (32-entries) prior switching PB_OCN_BAR1 from BOOT * mode. - * + * * initialize pointer to LUT associated with PB_OCN_BAR1 */ reg_ptr = - (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800); + (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x800); for (i = 0; i < 32; i++) { *reg_ptr++ = pb2ocn_lut1[i].lower; *reg_ptr++ = pb2ocn_lut1[i].upper; } - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("sync"); /* Base addresses for Cs0, CS1, CS2, CS3 */ - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR, - 0x00000000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_ADDR, + 0x00000000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR, - 0x00100000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_ADDR, + 0x00100000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR, - 0x00200000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_ADDR, + 0x00200000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR, - 0x00300000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_ADDR, + 0x00300000); + __asm__ __volatile__ ("sync"); /* Masks for HLP banks */ - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK, - 0xFFF00000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_MASK, + 0xFFF00000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK, - 0xFFF00000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_MASK, + 0xFFF00000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK, - 0xFFF00000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_MASK, + 0xFFF00000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK, - 0xFFF00000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_MASK, + 0xFFF00000); + __asm__ __volatile__ ("sync"); /* Set CTRL0 values for banks */ - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0, - 0x7FFC44C2); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL0, + 0x7FFC44C2); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0, - 0x7FFC44C0); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL0, + 0x7FFC44C0); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0, - 0x7FFC44C0); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL0, + 0x7FFC44C0); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0, - 0x7FFC44C2); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL0, + 0x7FFC44C2); + __asm__ __volatile__ ("sync"); /* Set banks to latched mode, enabled, and other default settings */ - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1, - 0x7C0F2000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B0_CTRL1, + 0x7C0F2000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1, - 0x7C0F2000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B1_CTRL1, + 0x7C0F2000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1, - 0x7C0F2000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B2_CTRL1, + 0x7C0F2000); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1, - 0x7C0F2000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1, + 0x7C0F2000); + __asm__ __volatile__ ("sync"); /* * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode. * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable) */ - out32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1, - 0xE0000011); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1, + 0xE0000011); + __asm__ __volatile__ ("sync"); - /* Make sure that OCN_BAR2 decoder is set (to allow following - * immediate read from SDRAM) + /* Make sure that OCN_BAR2 decoder is set (to allow following + * immediate read from SDRAM) */ - + temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1); - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("sync"); /* * SRI: At this point we have enabled the HLP banks. That means we can * now read from the NVRAM and initialize the environment variables. * We will over-ride the env_init called in board_init_f * This is really a work-around because, the HLP bank 1 - * where NVRAM resides is not visible during board_init_f + * where NVRAM resides is not visible during board_init_f * (lib_ppc/board.c) * Alternatively, we could use the I2C EEPROM at start-up to configure * and enable all HLP banks and not just HLP 0 as is being done for * Taiga Rev. 2. */ - env_init(); + env_init (); #ifndef DISABLE_PBM /* - * For IBM processors we have to set Address-Only commands generated + * For IBM processors we have to set Address-Only commands generated * by PBM that are different from ones set after reset. */ - temp = get_cpu_type(); + temp = get_cpu_type (); - if ((CPU_750FX == temp) || (CPU_750GX == temp)) { - out32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD, - 0x00009955); - } + if ((CPU_750FX == temp) || (CPU_750GX == temp)) + out32 (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_MCMD, + 0x00009955); #endif /* DISABLE_PBM */ #ifdef CONFIG_PCI @@ -350,42 +350,42 @@ int board_early_init_r(void) */ /* Map PCI/X Configuration Space (16MB @ 0x0_FE000000) */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0_UPPER, - 0); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + + PCI_PFAB_BAR0_UPPER, 0); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0, - 0xFB000001); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_BAR0, + 0xFB000001); + __asm__ __volatile__ ("sync"); /* Set Bus Number for the attached PCI/X bus (we will use 0 for NB) */ - temp = - in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT); + temp = in32(CFG_TSI108_CSR_BASE + + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT); temp &= ~0xFF00; /* Clear the BUS_NUM field */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT, - temp); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PCIX_STAT, + temp); /* Map PCI/X IO Space (64KB @ 0x0_FD000000) takes one 16MB LUT entry */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER, - 0); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO_UPPER, + 0); + __asm__ __volatile__ ("sync"); /* This register is on the PCI side to interpret the address it receives - * and maps it as a IO address. + * and maps it as a IO address. */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO, - 0xFA000001); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_PFAB_IO, + 0xFA000001); + __asm__ __volatile__ ("sync"); /* * Map PCI/X Memory Space * - * Transactions directed from OCM to PCI Memory Space are directed + * Transactions directed from OCM to PCI Memory Space are directed * from PB to PCI * unchanged (as defined by PB_OCN_BAR1,2 and LUT settings). * If address remapping is required the corresponding PCI_PFAB_MEM32 @@ -393,7 +393,7 @@ int board_early_init_r(void) * * Map the path from the PCI/X bus into the system memory * - * The memory mapped window assotiated with PCI P2O_BAR2 provides + * The memory mapped window assotiated with PCI P2O_BAR2 provides * access to the system memory without address remapping. * All system memory is opened for accesses initiated by PCI/X bus * masters. @@ -404,13 +404,13 @@ int board_early_init_r(void) */ reg_ptr = - (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500); + (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x500); #ifdef DISABLE_PBM - /* In case when PBM is disabled (no HW supported cache snoopng on PB) - * P2O_BAR2 is directly mapped into the system memory without address - * translation. + /* In case when PBM is disabled (no HW supported cache snoopng on PB) + * P2O_BAR2 is directly mapped into the system memory without address + * translation. */ reg_val = 0x00000004; /* SDRAM port + NO Addr_Translation */ @@ -438,30 +438,30 @@ int board_early_init_r(void) reg_val = 0x00007100; #endif - __asm__ __volatile__("eieio"); - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("eieio"); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES, - reg_val); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES, + reg_val); + __asm__ __volatile__ ("sync"); - /* Set 64-bit PCI bus address for system memory - * ( 0 is the best choice for easy mapping) + /* Set 64-bit PCI bus address for system memory + * ( 0 is the best choice for easy mapping) */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2, - 0x00000000); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER, - 0x00000000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2, + 0x00000000); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR2_UPPER, + 0x00000000); + __asm__ __volatile__ ("sync"); #ifndef DISABLE_PBM /* - * The memory mapped window assotiated with PCI P2O_BAR3 provides - * access to the system memory using SDRAM OCN port and address - * translation. This is alternative way to access SDRAM from PCI + * The memory mapped window assotiated with PCI P2O_BAR3 provides + * access to the system memory using SDRAM OCN port and address + * translation. This is alternative way to access SDRAM from PCI * required for Tsi108 emulation testing. - * All system memory is opened for accesses initiated by + * All system memory is opened for accesses initiated by * PCI/X bus masters. * * Initialize LUT associated with PCI P2O_BAR3 @@ -469,7 +469,7 @@ int board_early_init_r(void) * set pointer to LUT associated with PCI P2O_BAR3 */ reg_ptr = - (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600); + (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + 0x600); reg_val = 0x00000004; /* Destination port = SDC */ @@ -483,45 +483,45 @@ int board_early_init_r(void) reg_val += 0x01000000; } - __asm__ __volatile__("eieio"); - __asm__ __volatile__("sync"); + __asm__ __volatile__ ("eieio"); + __asm__ __volatile__ ("sync"); /* Configure PCI P2O_BAR3 (size = 512MB, Enabled) */ reg_val = - in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + + in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES); reg_val &= ~0x00FF; reg_val |= 0x0071; - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES, - reg_val); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_PAGE_SIZES, + reg_val); + __asm__ __volatile__ ("sync"); /* Set 64-bit base PCI bus address for window (0x20000000) */ - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER, - 0x00000000); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3, - 0x20000000); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3_UPPER, + 0x00000000); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR3, + 0x20000000); + __asm__ __volatile__ ("sync"); #endif /* !DISABLE_PBM */ #ifdef ENABLE_PCI_CSR_BAR /* open if required access to Tsi108 CSRs from the PCI/X bus */ /* enable BAR0 on the PCI/X bus */ - reg_val = - in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR); + reg_val = in32(CFG_TSI108_CSR_BASE + + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR); reg_val |= 0x02; - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR, - reg_val); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_MISC_CSR, + reg_val); + __asm__ __volatile__ ("sync"); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER, - 0x00000000); - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0, - CFG_TSI108_CSR_BASE); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0_UPPER, + 0x00000000); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_P2O_BAR0, + CFG_TSI108_CSR_BASE); + __asm__ __volatile__ ("sync"); #endif @@ -531,32 +531,32 @@ int board_early_init_r(void) reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR); reg_val |= 0x06; - out32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val); + __asm__ __volatile__ ("sync"); #endif /* CONFIG_PCI */ /* * Initialize MPIC outputs (interrupt pins): * Interrupt routing on the Grendel Emul. Board: - * PB_INT[0] -> INT (CPU0) - * PB_INT[1] -> INT (CPU1) - * PB_INT[2] -> MCP (CPU0) - * PB_INT[3] -> MCP (CPU1) + * PB_INT[0] -> INT (CPU0) + * PB_INT[1] -> INT (CPU1) + * PB_INT[2] -> MCP (CPU0) + * PB_INT[3] -> MCP (CPU1) * Set interrupt controller outputs as Level_Sensitive/Active_Low */ - out32(CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02); - out32(CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02); - out32(CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02); - out32(CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02); - __asm__ __volatile__("sync"); + out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(0), 0x02); + out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(1), 0x02); + out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(2), 0x02); + out32 (CFG_TSI108_CSR_BASE + TSI108_MPIC_REG_OFFSET + MPIC_CSR(3), 0x02); + __asm__ __volatile__ ("sync"); /* * Ensure that Machine Check exception is enabled * We need it to support PCI Bus probing (configuration reads) */ - reg_val = mfmsr(); + reg_val = mfmsr (); mtmsr(reg_val | MSR_ME); return 0; @@ -567,7 +567,7 @@ int board_early_init_r(void) * used in the misc_init_r function */ -unsigned long get_l2cr(void) +unsigned long get_l2cr (void) { unsigned long l2controlreg; asm volatile ("mfspr %0, 1017":"=r" (l2controlreg):); @@ -581,79 +581,82 @@ unsigned long get_l2cr(void) * */ -int misc_init_r(void) +int misc_init_r (void) { DECLARE_GLOBAL_DATA_PTR; #ifdef CFG_CLK_SPREAD /* Initialize Spread-Spectrum Clock generation */ ulong i; /* Ensure that Spread-Spectrum is disabled */ - out32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0); - out32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0); + out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, 0); + out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0); /* Initialize PLL1: CG_PCI_CLK , internal OCN_CLK * Uses pre-calculated value for Fout = 800 MHz, Fs = 30 kHz, D = 0.5% */ - out32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0x002e0044); /* D = 0.25% */ - out32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1, 0x00000039); /* BWADJ */ + out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, + 0x002e0044); /* D = 0.25% */ + out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL1, + 0x00000039); /* BWADJ */ /* Initialize PLL0: CG_PB_CLKO */ /* Detect PB clock freq. */ i = in32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PWRUP_STATUS); i = (i >> 16) & 0x07; /* Get PB PLL multiplier */ - out32(CFG_TSI108_CSR_BASE + - TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0); - out32(CFG_TSI108_CSR_BASE + - TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1); + out32 (CFG_TSI108_CSR_BASE + + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, pll0_config[i].ctrl0); + out32 (CFG_TSI108_CSR_BASE + + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL1, pll0_config[i].ctrl1); /* Wait and set SSEN for both PLL0 and 1 */ - udelay(1000); - out32(CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, 0x802e0044); /* D=0.25% */ - out32(CFG_TSI108_CSR_BASE + - TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, - 0x80000000 | pll0_config[i].ctrl0); + udelay (1000); + out32 (CFG_TSI108_CSR_BASE + TSI108_CLK_REG_OFFSET + CG_PLL1_CTRL0, + 0x802e0044); /* D=0.25% */ + out32 (CFG_TSI108_CSR_BASE + + TSI108_CLK_REG_OFFSET + CG_PLL0_CTRL0, + 0x80000000 | pll0_config[i].ctrl0); #endif /* CFG_CLK_SPREAD */ #ifdef CFG_L2 - l2cache_enable(); + l2cache_enable (); #endif - printf("BUS: %d MHz\n", gd->bus_clk / 1000000); - printf("MEM: %d MHz\n", gd->mem_clk / 1000000); + printf ("BUS: %d MHz\n", gd->bus_clk / 1000000); + printf ("MEM: %d MHz\n", gd->mem_clk / 1000000); /* - * All the information needed to print the cache details is avaiblable - * at this point i.e. above call to l2cache_enable is the very last - * thing done with regards to enabling diabling the cache. + * All the information needed to print the cache details is avaiblable + * at this point i.e. above call to l2cache_enable is the very last + * thing done with regards to enabling diabling the cache. * So this seems like a good place to print all this information */ - printf("CACHE: "); + printf ("CACHE: "); switch (get_cpu_type()) { case CPU_7447A: - printf("L1 Instruction cache - 32KB 8-way"); - (get_hid0() & (1 << 15)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); - printf(" L1 Data cache - 32KB 8-way"); - (get_hid0() & (1 << 14)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); - printf(" Unified L2 cache - 512KB 8-way"); - (get_l2cr() & (1 << 31)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); - printf("\n"); + printf ("L1 Instruction cache - 32KB 8-way"); + (get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); + printf ("L1 Data cache - 32KB 8-way"); + (get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); + printf ("Unified L2 cache - 512KB 8-way"); + (get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); + printf ("\n"); break; case CPU_7448: - printf("L1 Instruction cache - 32KB 8-way"); - (get_hid0() & (1 << 15)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); - printf(" L1 Data cache - 32KB 8-way"); - (get_hid0() & (1 << 14)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); - printf(" Unified L2 cache - 1MB 8-way"); - (get_l2cr() & (1 << 31)) ? printf(" ENABLED\n") : - printf(" DISABLED\n"); + printf ("L1 Instruction cache - 32KB 8-way"); + (get_hid0 () & (1 << 15)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); + printf ("L1 Data cache - 32KB 8-way"); + (get_hid0 () & (1 << 14)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); + printf ("Unified L2 cache - 1MB 8-way"); + (get_l2cr () & (1 << 31)) ? printf (" ENABLED\n") : + printf (" DISABLED\n"); break; default: break; diff --git a/cpu/74xx_7xx/cpu.c b/cpu/74xx_7xx/cpu.c index c3aadca2928..fc3b09217f7 100644 --- a/cpu/74xx_7xx/cpu.c +++ b/cpu/74xx_7xx/cpu.c @@ -303,7 +303,7 @@ watchdog_reset(void) #ifdef CONFIG_OF_FLAT_TREE void -ft_cpu_setup(void *blob, bd_t *bd) +ft_cpu_setup (void *blob, bd_t *bd) { u32 *p; ulong clock; @@ -311,18 +311,18 @@ ft_cpu_setup(void *blob, bd_t *bd) clock = bd->bi_busfreq; - p = ft_get_prop(blob, "/cpus/" OF_CPU "/bus-frequency", &len); + p = ft_get_prop (blob, "/cpus/" OF_CPU "/bus-frequency", &len); if (p != NULL) - *p = cpu_to_be32(clock); + *p = cpu_to_be32 (clock); #if defined(CONFIG_TSI108_ETH) - p = ft_get_prop(blob, "/" OF_TSI "/ethernet@6200/address", &len); - memcpy(p, bd->bi_enetaddr, 6); + p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6200/address", &len); + memcpy (p, bd->bi_enetaddr, 6); #endif - + #if defined(CONFIG_HAS_ETH1) - p = ft_get_prop(blob, "/" OF_TSI "/ethernet@6600/address", &len); - memcpy(p, bd->bi_enet1addr, 6); + p = ft_get_prop (blob, "/" OF_TSI "/ethernet@6600/address", &len); + memcpy (p, bd->bi_enet1addr, 6); #endif } #endif diff --git a/cpu/74xx_7xx/speed.c b/cpu/74xx_7xx/speed.c index d520794568a..af4aca5c343 100644 --- a/cpu/74xx_7xx/speed.c +++ b/cpu/74xx_7xx/speed.c @@ -31,7 +31,7 @@ DECLARE_GLOBAL_DATA_PTR; -extern unsigned long get_board_bus_clk(void); +extern unsigned long get_board_bus_clk (void); static const int hid1_multipliers_x_10[] = { 25, /* 0000 - 2.5x */ @@ -53,38 +53,38 @@ static const int hid1_multipliers_x_10[] = { }; static const int hid1_7447A_multipliers_x_10[] = { - 115, /* 00000 - 11.5x */ - 170, /* 00001 - 17x */ - 75, /* 00010 - 7.5x */ - 150, /* 00011 - 15x */ - 70, /* 00100 - 7x */ - 180, /* 00101 - 18x */ - 10, /* 00110 - bypass */ - 200, /* 00111 - 20x */ - 20, /* 01000 - 2x */ - 210, /* 01001 - 21x */ - 65, /* 01010 - 6.5x */ - 130, /* 01011 - 13x */ - 85, /* 01100 - 8.5x */ - 240, /* 01101 - 13x */ - 95, /* 01110 - 9.5x */ - 90, /* 01111 - 9x */ - 30, /* 10000 - 3x */ - 105, /* 10001 - 10.5x */ - 55, /* 10010 - 5.5x */ - 110, /* 10011 - 11x */ - 40, /* 10100 - 4x */ - 100, /* 10101 - 10x */ - 50, /* 10110 - 5x */ - 120, /* 10111 - 12x */ - 80, /* 11000 - 8x */ - 140, /* 11001 - 14x */ - 60, /* 11010 - 6x */ - 160, /* 11011 - 16x */ - 135, /* 11100 - 13.5x */ - 280, /* 11101 - 28x */ - 0, /* 11110 - off */ - 125 /* 11111 - 12.5x */ + 115, /* 00000 - 11.5x */ + 170, /* 00001 - 17x */ + 75, /* 00010 - 7.5x */ + 150, /* 00011 - 15x */ + 70, /* 00100 - 7x */ + 180, /* 00101 - 18x */ + 10, /* 00110 - bypass */ + 200, /* 00111 - 20x */ + 20, /* 01000 - 2x */ + 210, /* 01001 - 21x */ + 65, /* 01010 - 6.5x */ + 130, /* 01011 - 13x */ + 85, /* 01100 - 8.5x */ + 240, /* 01101 - 13x */ + 95, /* 01110 - 9.5x */ + 90, /* 01111 - 9x */ + 30, /* 10000 - 3x */ + 105, /* 10001 - 10.5x */ + 55, /* 10010 - 5.5x */ + 110, /* 10011 - 11x */ + 40, /* 10100 - 4x */ + 100, /* 10101 - 10x */ + 50, /* 10110 - 5x */ + 120, /* 10111 - 12x */ + 80, /* 11000 - 8x */ + 140, /* 11001 - 14x */ + 60, /* 11010 - 6x */ + 160, /* 11011 - 16x */ + 135, /* 11100 - 13.5x */ + 280, /* 11101 - 28x */ + 0, /* 11110 - off */ + 125 /* 11111 - 12.5x */ }; static const int hid1_fx_multipliers_x_10[] = { @@ -127,16 +127,17 @@ int get_clocks (void) ulong clock = 0; #ifdef CFG_CONFIG_BUS_CLK - gd->bus_clk = get_board_bus_clk(); + gd->bus_clk = get_board_bus_clk (); /* bus clock is configurable */ #else - gd->bus_clk = CFG_BUS_CLK; + gd->bus_clk = CFG_BUS_CLK; /* bus clock is a fixed frequency */ #endif /* calculate the clock frequency based upon the CPU type */ switch (get_cpu_type()) { case CPU_7447A: case CPU_7448: - clock = (gd->bus_clk / 10) * hid1_7447A_multipliers_x_10[(get_hid1 () >> 12) & 0x1F]; + clock = (gd->bus_clk / 10) * + hid1_7447A_multipliers_x_10[(get_hid1 () >> 12) & 0x1F]; break; case CPU_7455: @@ -146,12 +147,14 @@ int get_clocks (void) * Make sure division is done before multiplication to prevent 32-bit * arithmetic overflows which will cause a negative number */ - clock = (gd->bus_clk / 10) * hid1_multipliers_x_10[(get_hid1 () >> 13) & 0xF]; + clock = (gd->bus_clk / 10) * + hid1_multipliers_x_10[(get_hid1 () >> 13) & 0xF]; break; case CPU_750GX: case CPU_750FX: - clock = gd->bus_clk * hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10; + clock = gd->bus_clk * + hid1_fx_multipliers_x_10[get_hid1 () >> 27] / 10; break; case CPU_7450: @@ -168,7 +171,8 @@ int get_clocks (void) * Make sure division is done before multiplication to prevent 32-bit * arithmetic overflows which will cause a negative number */ - clock = (gd->bus_clk / 10) * hid1_multipliers_x_10[get_hid1 () >> 28]; + clock = (gd->bus_clk / 10) * + hid1_multipliers_x_10[get_hid1 () >> 28]; break; case CPU_UNKNOWN: diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2 index 5142a0f6385..0e40e39269b 100644 --- a/doc/README.mpc7448hpc2 +++ b/doc/README.mpc7448hpc2 @@ -3,23 +3,23 @@ Freescale MPC7448hpc2 (Taiga) board Created 08/11/2006 Roy Zang -------------------------- -MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference -design, which is optimized for high speed throughput between the processor and +MPC7448hpc2 (Taiga) board is a high-performance PowerPC server reference +design, which is optimized for high speed throughput between the processor and the memory, disk drive and Ethernet port subsystems. -MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be -used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX +MPC7448hpc2(Taiga) is designed to the micro-ATX chassis, allowing it to be +used in 1U or 2U rack-mount chassis¡¯, as well as in standard ATX/Micro-ATX chassis. Building U-Boot ------------------ The mpc7448hpc2 code base is known to compile using: - Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 + Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3 - $ make mpc7448hpc2_config - Configuring for mpc7448hpc2 board... + $ make mpc7448hpc2_config + Configuring for mpc7448hpc2 board... - $ make + $ make Memory Map ---------- @@ -28,25 +28,24 @@ The memory map is setup for Linux to operate properly. The mapping is: - Range Start Range End Definition Size - - 0x0000_0000 0x7fff_ffff DDR 2G - 0xe000_0000 0xe7ff_ffff PCI Memory 128M - 0xfa00_0000 0xfaff_ffff PCI IO 16M - 0xfb00_0000 0xfbff_ffff PCI Config 16M - 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M - 0xfe00_0000 0xfeff_ffff PromJet 16M - 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M - 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M + Range Start Range End Definition Size + 0x0000_0000 0x7fff_ffff DDR 2G + 0xe000_0000 0xe7ff_ffff PCI Memory 128M + 0xfa00_0000 0xfaff_ffff PCI IO 16M + 0xfb00_0000 0xfbff_ffff PCI Config 16M + 0xfc00_0000 0xfc0f_ffff NVRAM/CADMUS 1M + 0xfe00_0000 0xfeff_ffff PromJet 16M + 0xff00_0000 0xff80_0000 FLASH (boot flash) 8M + 0xff80_0000 0xffff_ffff FLASH (second half flash) 8M Using Flash ----------- -The MPC7448hpc2 board has two "banks" of flash, each 8MB in size -(2^23 = 0x00800000). +The MPC7448hpc2 board has two "banks" of flash, each 8MB in size +(2^23 = 0x00800000). -Note: the "bank" here refers to half of the flash. In fact, there is only one +Note: the "bank" here refers to half of the flash. In fact, there is only one bank of flash, which is divided into low and high half. Each is controlled by the most significant bit of the address bus. The so called "bank" is only for convenience. @@ -57,137 +56,130 @@ settings for updating flash are given below. The u-boot commands for copying the boot-bank into the secondary bank are as follows: - erase ff800000 ff880000 - cp.b ff000000 ff800000 80000 + erase ff800000 ff880000 + cp.b ff000000 ff800000 80000 U-boot commands for downloading an image via tftp and flashing it into the secondary bank: - tftp 10000 - erase ff000000 ff080000 - cp.b 10000 ff000000 80000 - + tftp 10000 + erase ff000000 ff080000 + cp.b 10000 ff000000 80000 After copying the image into the second bank of flash, be sure to toggle SW3[4] on board before resetting the board in order to set the secondary bank as the boot-bank. - Board Switches ---------------------- - Most switches on the board should not be changed. The most frequent user-settable switches on the board are used to configure the flash banks and determining the PCI frequency. SW1[1-5]: Processor core voltage - 12345 Core Voltage - ----- - SW1=01111 1.000V. - SW1=01101 1.100V. - SW1=01011 1.200V. - SW1=01001 1.300V only for MPC7447A. + 12345 Core Voltage + ----- + SW1=01111 1.000V. + SW1=01101 1.100V. + SW1=01011 1.200V. + SW1=01001 1.300V only for MPC7447A. SW2[1-6]: CPU core frequency - CPU Core Frequency (MHz) + CPU Core Frequency (MHz) Bus Frequency - 123456 100 133 167 200 Ratio + 123456 100 133 167 200 Ratio - ------ - SW2=101100 500 667 833 1000 5x - SW2=100100 550 733 917 1100 5.5x - SW2=110100 600 800 1000 1200 6x - SW2=010100 650 866 1083 1300 6.5x - SW2=001000 700 930 1167 1400 7x - SW2=000100 750 1000 1250 1500 7.5x - SW2=110000 800 1066 1333 1600 8x - SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A - SW2=011110 900 1200 1500 1800 9x - -This table shows only a subset of available frequency options; see the CPU + ------ + SW2=101100 500 667 833 1000 5x + SW2=100100 550 733 917 1100 5.5x + SW2=110100 600 800 1000 1200 6x + SW2=010100 650 866 1083 1300 6.5x + SW2=001000 700 930 1167 1400 7x + SW2=000100 750 1000 1250 1500 7.5x + SW2=110000 800 1066 1333 1600 8x + SW2=011000 850 1333 1417 1700 8.5x only for MPC7447A + SW2=011110 900 1200 1500 1800 9x + +This table shows only a subset of available frequency options; see the CPU hardware specifications for more information. - SW2[7-8]: Bus Protocol and CPU Reset Option - 7 - - - SW2=0 System bus uses MPX bus protocol - SW2=1 System bus uses 60x bus protocol - - 8 - - - SW2=0 TSI108 can cause CPU reset - SW2=1 TSI108 can not cause CPU reset + 7 + - + SW2=0 System bus uses MPX bus protocol + SW2=1 System bus uses 60x bus protocol + 8 + - + SW2=0 TSI108 can cause CPU reset + SW2=1 TSI108 can not cause CPU reset SW3[1-8] system options - 123 - --- - SW3=xxx Connected to GPIO[0:2] on TSI108 + 123 + --- + SW3=xxx Connected to GPIO[0:2] on TSI108 - 4 - - - SW3=0 CPU boots from low half of flash - SW3=1 CPU boots from high half of flash + 4 + - + SW3=0 CPU boots from low half of flash + SW3=1 CPU boots from high half of flash - 5 - - - SW3=0 SATA and slot2 connected to PCI bus - SW3=1 Only slot1 connected to PCI bus + 5 + - + SW3=0 SATA and slot2 connected to PCI bus + SW3=1 Only slot1 connected to PCI bus - 6 - - - SW3=0 USB connected to PCI bus - SW3=1 USB disconnected from PCI bus + 6 + - + SW3=0 USB connected to PCI bus + SW3=1 USB disconnected from PCI bus - 7 - - - SW3=0 Flash is write protected - SW3=1 Flash is NOT write protected + 7 + - + SW3=0 Flash is write protected + SW3=1 Flash is NOT write protected - 8 - - - SW3=0 CPU will boot from flash - SW3=1 CPU will boot from PromJet + 8 + - + SW3=0 CPU will boot from flash + SW3=1 CPU will boot from PromJet SW4[1-3]: System bus frequency Bus Frequency (MHz) - --- - SW4=010 183 - SW4=011 100 - SW4=100 133 - SW4=101 166 only for MPC7447A - SW4=110 200 only for MPC7448 - others reserved - + --- + SW4=010 183 + SW4=011 100 + SW4=100 133 + SW4=101 166 only for MPC7447A + SW4=110 200 only for MPC7448 + others reserved SW4[4-6]: DDR2 SDRAM frequency Bus Frequency (MHz) - --- - SW4=000 external clock - SW4=011 system clock - SW4=100 133 - SW4=101 166 - SW4=110 200 - others reserved - + --- + SW4=000 external clock + SW4=011 system clock + SW4=100 133 + SW4=101 166 + SW4=110 200 + others reserved SW4[7-8]: PCI/PCI-X frequency control - 7 - - - SW4=0 PCI/PCI-X bus operates normally - SW4=1 PCI bus forced to PCI-33 mode - - 8 - - - SW4=0 PCI-X mode at 133 MHz allowed - SW4=1 PCI-X mode limited to 100 MHz + 7 + - + SW4=0 PCI/PCI-X bus operates normally + SW4=1 PCI bus forced to PCI-33 mode + + 8 + - + SW4=0 PCI-X mode at 133 MHz allowed + SW4=1 PCI-X mode limited to 100 MHz diff --git a/drivers/tsi108_eth.c b/drivers/tsi108_eth.c index d95a047ce85..47341bee7f1 100644 --- a/drivers/tsi108_eth.c +++ b/drivers/tsi108_eth.c @@ -46,7 +46,9 @@ #endif #if TSI108_ETH_DEBUG > 0 -#define debug_lev(lev, fmt, args...) if (lev <= TSI108_ETH_DEBUG) printf("%s %d: " fmt, __FUNCTION__, __LINE__, ##args) +#define debug_lev(lev, fmt, args...) \ +if (lev <= TSI108_ETH_DEBUG) \ +printf ("%s %d: " fmt, __FUNCTION__, __LINE__, ##args) #else #define debug_lev(lev, fmt, args...) do{}while(0) #endif @@ -54,322 +56,322 @@ #define RX_PRINT_ERRORS #define TX_PRINT_ERRORS -#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000) +#define ETH_BASE (CFG_TSI108_CSR_BASE + 0x6000) -#define ETH_PORT_OFFSET 0x400 +#define ETH_PORT_OFFSET 0x400 #define __REG32(base, offset) (*((volatile u32 *)((char *)(base) + (offset)))) -#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000) -#define MAC_CONFIG_1_TX_ENABLE (0x00000001) -#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002) -#define MAC_CONFIG_1_RX_ENABLE (0x00000004) -#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008) -#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010) -#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020) -#define MAC_CONFIG_1_LOOP_BACK (0x00000100) -#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000) -#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000) -#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000) -#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000) -#define MAC_CONFIG_1_SIM_RESET (0x40000000) -#define MAC_CONFIG_1_SOFT_RESET (0x80000000) - -#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004) -#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001) -#define MAC_CONFIG_2_CRC_ENABLE (0x00000002) -#define MAC_CONFIG_2_PAD_CRC (0x00000004) -#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010) -#define MAC_CONFIG_2_HUGE_FRAME (0x00000020) -#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8) -#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12) -#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */ -#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */ - -#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010) - -#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020) -#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7) -#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010) -#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020) -#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000) - -#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024) -#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001) -#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002) - -#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028) -#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c) -#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030) - -#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034) -#define MII_MGMT_INDICATORS_BUSY (0x00000001) -#define MII_MGMT_INDICATORS_SCAN (0x00000002) -#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004) - -#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c) -#define INTERFACE_STATUS_LINK_FAIL (0x00000008) -#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200) - -#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040) -#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044) - -#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200) -#define PORT_CONTROL_PRI (0x00000001) -#define PORT_CONTROL_BPT (0x00010000) -#define PORT_CONTROL_SPD (0x00040000) -#define PORT_CONTROL_RBC (0x00080000) -#define PORT_CONTROL_PRB (0x00200000) -#define PORT_CONTROL_DIS (0x00400000) -#define PORT_CONTROL_TBI (0x00800000) -#define PORT_CONTROL_STE (0x10000000) -#define PORT_CONTROL_ZOR (0x20000000) -#define PORT_CONTROL_CLR (0x40000000) -#define PORT_CONTROL_SRT (0x80000000) - -#define reg_TX_CONFIG(base) __REG32(base, 0x00000220) -#define TX_CONFIG_START_Q (0x00000003) -#define TX_CONFIG_EHP (0x00400000) -#define TX_CONFIG_CHP (0x00800000) -#define TX_CONFIG_RST (0x80000000) - -#define reg_TX_CONTROL(base) __REG32(base, 0x00000224) -#define TX_CONTROL_GO (0x00008000) -#define TX_CONTROL_MP (0x01000000) -#define TX_CONTROL_EAI (0x20000000) -#define TX_CONTROL_ABT (0x40000000) -#define TX_CONTROL_EII (0x80000000) - -#define reg_TX_STATUS(base) __REG32(base, 0x00000228) -#define TX_STATUS_QUEUE_USABLE (0x0000000f) -#define TX_STATUS_CURR_Q (0x00000300) -#define TX_STATUS_ACT (0x00008000) -#define TX_STATUS_QUEUE_IDLE (0x000f0000) -#define TX_STATUS_EOQ_PENDING (0x0f000000) - -#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c) -#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f) -#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00) -#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) -#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) - -#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230) +#define reg_MAC_CONFIG_1(base) __REG32(base, 0x00000000) +#define MAC_CONFIG_1_TX_ENABLE (0x00000001) +#define MAC_CONFIG_1_SYNC_TX_ENABLE (0x00000002) +#define MAC_CONFIG_1_RX_ENABLE (0x00000004) +#define MAC_CONFIG_1_SYNC_RX_ENABLE (0x00000008) +#define MAC_CONFIG_1_TX_FLOW_CONTROL (0x00000010) +#define MAC_CONFIG_1_RX_FLOW_CONTROL (0x00000020) +#define MAC_CONFIG_1_LOOP_BACK (0x00000100) +#define MAC_CONFIG_1_RESET_TX_FUNCTION (0x00010000) +#define MAC_CONFIG_1_RESET_RX_FUNCTION (0x00020000) +#define MAC_CONFIG_1_RESET_TX_MAC (0x00040000) +#define MAC_CONFIG_1_RESET_RX_MAC (0x00080000) +#define MAC_CONFIG_1_SIM_RESET (0x40000000) +#define MAC_CONFIG_1_SOFT_RESET (0x80000000) + +#define reg_MAC_CONFIG_2(base) __REG32(base, 0x00000004) +#define MAC_CONFIG_2_FULL_DUPLEX (0x00000001) +#define MAC_CONFIG_2_CRC_ENABLE (0x00000002) +#define MAC_CONFIG_2_PAD_CRC (0x00000004) +#define MAC_CONFIG_2_LENGTH_CHECK (0x00000010) +#define MAC_CONFIG_2_HUGE_FRAME (0x00000020) +#define MAC_CONFIG_2_INTERFACE_MODE(val) (((val) & 0x3) << 8) +#define MAC_CONFIG_2_PREAMBLE_LENGTH(val) (((val) & 0xf) << 12) +#define INTERFACE_MODE_NIBBLE 1 /* 10/100 Mb/s MII) */ +#define INTERFACE_MODE_BYTE 2 /* 1000 Mb/s GMII/TBI */ + +#define reg_MAXIMUM_FRAME_LENGTH(base) __REG32(base, 0x00000010) + +#define reg_MII_MGMT_CONFIG(base) __REG32(base, 0x00000020) +#define MII_MGMT_CONFIG_MGMT_CLOCK_SELECT(val) ((val) & 0x7) +#define MII_MGMT_CONFIG_NO_PREAMBLE (0x00000010) +#define MII_MGMT_CONFIG_SCAN_INCREMENT (0x00000020) +#define MII_MGMT_CONFIG_RESET_MGMT (0x80000000) + +#define reg_MII_MGMT_COMMAND(base) __REG32(base, 0x00000024) +#define MII_MGMT_COMMAND_READ_CYCLE (0x00000001) +#define MII_MGMT_COMMAND_SCAN_CYCLE (0x00000002) + +#define reg_MII_MGMT_ADDRESS(base) __REG32(base, 0x00000028) +#define reg_MII_MGMT_CONTROL(base) __REG32(base, 0x0000002c) +#define reg_MII_MGMT_STATUS(base) __REG32(base, 0x00000030) + +#define reg_MII_MGMT_INDICATORS(base) __REG32(base, 0x00000034) +#define MII_MGMT_INDICATORS_BUSY (0x00000001) +#define MII_MGMT_INDICATORS_SCAN (0x00000002) +#define MII_MGMT_INDICATORS_NOT_VALID (0x00000004) + +#define reg_INTERFACE_STATUS(base) __REG32(base, 0x0000003c) +#define INTERFACE_STATUS_LINK_FAIL (0x00000008) +#define INTERFACE_STATUS_EXCESS_DEFER (0x00000200) + +#define reg_STATION_ADDRESS_1(base) __REG32(base, 0x00000040) +#define reg_STATION_ADDRESS_2(base) __REG32(base, 0x00000044) + +#define reg_PORT_CONTROL(base) __REG32(base, 0x00000200) +#define PORT_CONTROL_PRI (0x00000001) +#define PORT_CONTROL_BPT (0x00010000) +#define PORT_CONTROL_SPD (0x00040000) +#define PORT_CONTROL_RBC (0x00080000) +#define PORT_CONTROL_PRB (0x00200000) +#define PORT_CONTROL_DIS (0x00400000) +#define PORT_CONTROL_TBI (0x00800000) +#define PORT_CONTROL_STE (0x10000000) +#define PORT_CONTROL_ZOR (0x20000000) +#define PORT_CONTROL_CLR (0x40000000) +#define PORT_CONTROL_SRT (0x80000000) + +#define reg_TX_CONFIG(base) __REG32(base, 0x00000220) +#define TX_CONFIG_START_Q (0x00000003) +#define TX_CONFIG_EHP (0x00400000) +#define TX_CONFIG_CHP (0x00800000) +#define TX_CONFIG_RST (0x80000000) + +#define reg_TX_CONTROL(base) __REG32(base, 0x00000224) +#define TX_CONTROL_GO (0x00008000) +#define TX_CONTROL_MP (0x01000000) +#define TX_CONTROL_EAI (0x20000000) +#define TX_CONTROL_ABT (0x40000000) +#define TX_CONTROL_EII (0x80000000) + +#define reg_TX_STATUS(base) __REG32(base, 0x00000228) +#define TX_STATUS_QUEUE_USABLE (0x0000000f) +#define TX_STATUS_CURR_Q (0x00000300) +#define TX_STATUS_ACT (0x00008000) +#define TX_STATUS_QUEUE_IDLE (0x000f0000) +#define TX_STATUS_EOQ_PENDING (0x0f000000) + +#define reg_TX_EXTENDED_STATUS(base) __REG32(base, 0x0000022c) +#define TX_EXTENDED_STATUS_END_OF_QUEUE_CONDITION (0x0000000f) +#define TX_EXTENDED_STATUS_END_OF_FRAME_CONDITION (0x00000f00) +#define TX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) +#define TX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) + +#define reg_TX_THRESHOLDS(base) __REG32(base, 0x00000230) #define reg_TX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000270) -#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) -#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000) -#define TX_DIAGNOSTIC_ADDR_AI (0x80000000) - -#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274) - -#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278) -#define TX_ERROR_STATUS (0x00000278) -#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f) -#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010) -#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020) -#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040) -#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080) -#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00) -#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000) -#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000) -#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000) -#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000) -#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000) -#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000) -#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000) -#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000) -#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000) -#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000) -#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000) -#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000) -#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000) -#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000) - -#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280) -#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) -#define TX_QUEUE_0_CONFIG_BSWP (0x00000400) -#define TX_QUEUE_0_CONFIG_WSWP (0x00000800) -#define TX_QUEUE_0_CONFIG_AM (0x00004000) -#define TX_QUEUE_0_CONFIG_GVI (0x00008000) -#define TX_QUEUE_0_CONFIG_EEI (0x00010000) -#define TX_QUEUE_0_CONFIG_ELI (0x00020000) -#define TX_QUEUE_0_CONFIG_ENI (0x00040000) -#define TX_QUEUE_0_CONFIG_ESI (0x00080000) -#define TX_QUEUE_0_CONFIG_EDI (0x00100000) - -#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284) -#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) -#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) -#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) -#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) - -#define OCN_PORT_HLP 0 /* HLP Interface */ -#define OCN_PORT_PCI_X 1 /* PCI-X Interface */ +#define TX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) +#define TX_DIAGNOSTIC_ADDR_DFR (0x40000000) +#define TX_DIAGNOSTIC_ADDR_AI (0x80000000) + +#define reg_TX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000274) + +#define reg_TX_ERROR_STATUS(base) __REG32(base, 0x00000278) +#define TX_ERROR_STATUS (0x00000278) +#define TX_ERROR_STATUS_QUEUE_0_ERROR_RESPONSE (0x0000000f) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_0 (0x00000010) +#define TX_ERROR_STATUS_RER_ON_QUEUE_0 (0x00000020) +#define TX_ERROR_STATUS_TER_ON_QUEUE_0 (0x00000040) +#define TX_ERROR_STATUS_DER_ON_QUEUE_0 (0x00000080) +#define TX_ERROR_STATUS_QUEUE_1_ERROR_RESPONSE (0x00000f00) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_1 (0x00001000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_1 (0x00002000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_1 (0x00004000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_1 (0x00008000) +#define TX_ERROR_STATUS_QUEUE_2_ERROR_RESPONSE (0x000f0000) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_2 (0x00100000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_2 (0x00200000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_2 (0x00400000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_2 (0x00800000) +#define TX_ERROR_STATUS_QUEUE_3_ERROR_RESPONSE (0x0f000000) +#define TX_ERROR_STATUS_TEA_ON_QUEUE_3 (0x10000000) +#define TX_ERROR_STATUS_RER_ON_QUEUE_3 (0x20000000) +#define TX_ERROR_STATUS_TER_ON_QUEUE_3 (0x40000000) +#define TX_ERROR_STATUS_DER_ON_QUEUE_3 (0x80000000) + +#define reg_TX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000280) +#define TX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) +#define TX_QUEUE_0_CONFIG_BSWP (0x00000400) +#define TX_QUEUE_0_CONFIG_WSWP (0x00000800) +#define TX_QUEUE_0_CONFIG_AM (0x00004000) +#define TX_QUEUE_0_CONFIG_GVI (0x00008000) +#define TX_QUEUE_0_CONFIG_EEI (0x00010000) +#define TX_QUEUE_0_CONFIG_ELI (0x00020000) +#define TX_QUEUE_0_CONFIG_ENI (0x00040000) +#define TX_QUEUE_0_CONFIG_ESI (0x00080000) +#define TX_QUEUE_0_CONFIG_EDI (0x00100000) + +#define reg_TX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000284) +#define TX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) +#define TX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) +#define TX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) +#define TX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) + +#define OCN_PORT_HLP 0 /* HLP Interface */ +#define OCN_PORT_PCI_X 1 /* PCI-X Interface */ #define OCN_PORT_PROCESSOR_MASTER 2 /* Processor Interface (master) */ -#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */ -#define OCN_PORT_MEMORY 4 /* Memory Controller */ -#define OCN_PORT_DMA 5 /* DMA Controller */ -#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */ -#define OCN_PORT_PRINT 7 /* Print Engine Interface */ - -#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288) - -#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c) -#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000) - -#define reg_RX_CONFIG(base) __REG32(base, 0x00000320) -#define RX_CONFIG_DEF_Q (0x00000003) -#define RX_CONFIG_EMF (0x00000100) -#define RX_CONFIG_EUF (0x00000200) -#define RX_CONFIG_BFE (0x00000400) -#define RX_CONFIG_MFE (0x00000800) -#define RX_CONFIG_UFE (0x00001000) -#define RX_CONFIG_SE (0x00002000) -#define RX_CONFIG_ABF (0x00200000) -#define RX_CONFIG_APE (0x00400000) -#define RX_CONFIG_CHP (0x00800000) -#define RX_CONFIG_RST (0x80000000) - -#define reg_RX_CONTROL(base) __REG32(base, 0x00000324) -#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f) -#define GE_E0_RX_CONTROL_GO (0x00008000) -#define GE_E0_RX_CONTROL_EAI (0x20000000) -#define GE_E0_RX_CONTROL_ABT (0x40000000) -#define GE_E0_RX_CONTROL_EII (0x80000000) - -#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c) -#define RX_EXTENDED_STATUS (0x0000032c) -#define RX_EXTENDED_STATUS_EOQ (0x0000000f) -#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001) -#define RX_EXTENDED_STATUS_EOF (0x00000f00) -#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) -#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) - -#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330) - -#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370) -#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) -#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000) -#define RX_DIAGNOSTIC_ADDR_AI (0x80000000) - -#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374) - -#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380) -#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) -#define RX_QUEUE_0_CONFIG_BSWP (0x00000400) -#define RX_QUEUE_0_CONFIG_WSWP (0x00000800) -#define RX_QUEUE_0_CONFIG_AM (0x00004000) -#define RX_QUEUE_0_CONFIG_EEI (0x00010000) -#define RX_QUEUE_0_CONFIG_ELI (0x00020000) -#define RX_QUEUE_0_CONFIG_ENI (0x00040000) -#define RX_QUEUE_0_CONFIG_ESI (0x00080000) -#define RX_QUEUE_0_CONFIG_EDI (0x00100000) - -#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384) -#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) -#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) -#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) -#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) - -#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388) - -#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c) -#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000) +#define OCN_PORT_PROCESSOR_SLAVE 3 /* Processor Interface (slave) */ +#define OCN_PORT_MEMORY 4 /* Memory Controller */ +#define OCN_PORT_DMA 5 /* DMA Controller */ +#define OCN_PORT_ETHERNET 6 /* Ethernet Controller */ +#define OCN_PORT_PRINT 7 /* Print Engine Interface */ + +#define reg_TX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000288) + +#define reg_TX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000028c) +#define TX_QUEUE_0_PTR_HIGH_VALID (0x80000000) + +#define reg_RX_CONFIG(base) __REG32(base, 0x00000320) +#define RX_CONFIG_DEF_Q (0x00000003) +#define RX_CONFIG_EMF (0x00000100) +#define RX_CONFIG_EUF (0x00000200) +#define RX_CONFIG_BFE (0x00000400) +#define RX_CONFIG_MFE (0x00000800) +#define RX_CONFIG_UFE (0x00001000) +#define RX_CONFIG_SE (0x00002000) +#define RX_CONFIG_ABF (0x00200000) +#define RX_CONFIG_APE (0x00400000) +#define RX_CONFIG_CHP (0x00800000) +#define RX_CONFIG_RST (0x80000000) + +#define reg_RX_CONTROL(base) __REG32(base, 0x00000324) +#define GE_E0_RX_CONTROL_QUEUE_ENABLES (0x0000000f) +#define GE_E0_RX_CONTROL_GO (0x00008000) +#define GE_E0_RX_CONTROL_EAI (0x20000000) +#define GE_E0_RX_CONTROL_ABT (0x40000000) +#define GE_E0_RX_CONTROL_EII (0x80000000) + +#define reg_RX_EXTENDED_STATUS(base) __REG32(base, 0x0000032c) +#define RX_EXTENDED_STATUS (0x0000032c) +#define RX_EXTENDED_STATUS_EOQ (0x0000000f) +#define RX_EXTENDED_STATUS_EOQ_0 (0x00000001) +#define RX_EXTENDED_STATUS_EOF (0x00000f00) +#define RX_EXTENDED_STATUS_DESCRIPTOR_INTERRUPT_CONDITION (0x000f0000) +#define RX_EXTENDED_STATUS_ERROR_FLAG (0x0f000000) + +#define reg_RX_THRESHOLDS(base) __REG32(base, 0x00000330) + +#define reg_RX_DIAGNOSTIC_ADDR(base) __REG32(base, 0x00000370) +#define RX_DIAGNOSTIC_ADDR_INDEX (0x0000007f) +#define RX_DIAGNOSTIC_ADDR_DFR (0x40000000) +#define RX_DIAGNOSTIC_ADDR_AI (0x80000000) + +#define reg_RX_DIAGNOSTIC_DATA(base) __REG32(base, 0x00000374) + +#define reg_RX_QUEUE_0_CONFIG(base) __REG32(base, 0x00000380) +#define RX_QUEUE_0_CONFIG_OCN_PORT (0x0000003f) +#define RX_QUEUE_0_CONFIG_BSWP (0x00000400) +#define RX_QUEUE_0_CONFIG_WSWP (0x00000800) +#define RX_QUEUE_0_CONFIG_AM (0x00004000) +#define RX_QUEUE_0_CONFIG_EEI (0x00010000) +#define RX_QUEUE_0_CONFIG_ELI (0x00020000) +#define RX_QUEUE_0_CONFIG_ENI (0x00040000) +#define RX_QUEUE_0_CONFIG_ESI (0x00080000) +#define RX_QUEUE_0_CONFIG_EDI (0x00100000) + +#define reg_RX_QUEUE_0_BUF_CONFIG(base) __REG32(base, 0x00000384) +#define RX_QUEUE_0_BUF_CONFIG_OCN_PORT (0x0000003f) +#define RX_QUEUE_0_BUF_CONFIG_BURST (0x00000300) +#define RX_QUEUE_0_BUF_CONFIG_BSWP (0x00000400) +#define RX_QUEUE_0_BUF_CONFIG_WSWP (0x00000800) + +#define reg_RX_QUEUE_0_PTR_LOW(base) __REG32(base, 0x00000388) + +#define reg_RX_QUEUE_0_PTR_HIGH(base) __REG32(base, 0x0000038c) +#define RX_QUEUE_0_PTR_HIGH_VALID (0x80000000) /* * PHY register definitions */ /* the first 15 PHY registers are standard. */ -#define PHY_CTRL_REG 0 /* Control Register */ -#define PHY_STATUS_REG 1 /* Status Regiser */ -#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */ -#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */ -#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */ -#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */ -#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */ -#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */ -#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */ -#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */ -#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */ -#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */ +#define PHY_CTRL_REG 0 /* Control Register */ +#define PHY_STATUS_REG 1 /* Status Regiser */ +#define PHY_ID1_REG 2 /* Phy Id Reg (word 1) */ +#define PHY_ID2_REG 3 /* Phy Id Reg (word 2) */ +#define PHY_AN_ADV_REG 4 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY_REG 5 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP_REG 6 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX_REG 7 /* Next Page TX */ +#define PHY_LP_NEXT_PAGE_REG 8 /* Link Partner Next Page */ +#define PHY_1000T_CTRL_REG 9 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS_REG 10 /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS_REG 11 /* Extended Status Reg */ /* * PHY Register bit masks. */ -#define PHY_CTRL_RESET (1 << 15) -#define PHY_CTRL_LOOPBACK (1 << 14) -#define PHY_CTRL_SPEED0 (1 << 13) -#define PHY_CTRL_AN_EN (1 << 12) -#define PHY_CTRL_PWR_DN (1 << 11) -#define PHY_CTRL_ISOLATE (1 << 10) -#define PHY_CTRL_RESTART_AN (1 << 9) -#define PHY_CTRL_FULL_DUPLEX (1 << 8) -#define PHY_CTRL_CT_EN (1 << 7) -#define PHY_CTRL_SPEED1 (1 << 6) - -#define PHY_STAT_100BASE_T4 (1 << 15) -#define PHY_STAT_100BASE_X_FD (1 << 14) -#define PHY_STAT_100BASE_X_HD (1 << 13) -#define PHY_STAT_10BASE_T_FD (1 << 12) -#define PHY_STAT_10BASE_T_HD (1 << 11) -#define PHY_STAT_100BASE_T2_FD (1 << 10) -#define PHY_STAT_100BASE_T2_HD (1 << 9) -#define PHY_STAT_EXT_STAT (1 << 8) -#define PHY_STAT_RESERVED (1 << 7) -#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */ -#define PHY_STAT_AN_COMPLETE (1 << 5) -#define PHY_STAT_REM_FAULT (1 << 4) -#define PHY_STAT_AN_CAP (1 << 3) -#define PHY_STAT_LINK_UP (1 << 2) -#define PHY_STAT_JABBER (1 << 1) -#define PHY_STAT_EXT_CAP (1 << 0) - -#define TBI_CONTROL_2 0x11 -#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001 -#define TBI_CONTROL_2_ENABLE_WRAP 0x0002 -#define TBI_CONTROL_2_G_MII_MODE 0x0010 -#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020 -#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100 -#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000 -#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000 -#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000 -#define TBI_CONTROL_2_SOFT_RESET 0x8000 +#define PHY_CTRL_RESET (1 << 15) +#define PHY_CTRL_LOOPBACK (1 << 14) +#define PHY_CTRL_SPEED0 (1 << 13) +#define PHY_CTRL_AN_EN (1 << 12) +#define PHY_CTRL_PWR_DN (1 << 11) +#define PHY_CTRL_ISOLATE (1 << 10) +#define PHY_CTRL_RESTART_AN (1 << 9) +#define PHY_CTRL_FULL_DUPLEX (1 << 8) +#define PHY_CTRL_CT_EN (1 << 7) +#define PHY_CTRL_SPEED1 (1 << 6) + +#define PHY_STAT_100BASE_T4 (1 << 15) +#define PHY_STAT_100BASE_X_FD (1 << 14) +#define PHY_STAT_100BASE_X_HD (1 << 13) +#define PHY_STAT_10BASE_T_FD (1 << 12) +#define PHY_STAT_10BASE_T_HD (1 << 11) +#define PHY_STAT_100BASE_T2_FD (1 << 10) +#define PHY_STAT_100BASE_T2_HD (1 << 9) +#define PHY_STAT_EXT_STAT (1 << 8) +#define PHY_STAT_RESERVED (1 << 7) +#define PHY_STAT_MFPS (1 << 6) /* Management Frames Preamble Suppression */ +#define PHY_STAT_AN_COMPLETE (1 << 5) +#define PHY_STAT_REM_FAULT (1 << 4) +#define PHY_STAT_AN_CAP (1 << 3) +#define PHY_STAT_LINK_UP (1 << 2) +#define PHY_STAT_JABBER (1 << 1) +#define PHY_STAT_EXT_CAP (1 << 0) + +#define TBI_CONTROL_2 0x11 +#define TBI_CONTROL_2_ENABLE_COMMA_DETECT 0x0001 +#define TBI_CONTROL_2_ENABLE_WRAP 0x0002 +#define TBI_CONTROL_2_G_MII_MODE 0x0010 +#define TBI_CONTROL_2_RECEIVE_CLOCK_SELECT 0x0020 +#define TBI_CONTROL_2_AUTO_NEGOTIATION_SENSE 0x0100 +#define TBI_CONTROL_2_DISABLE_TRANSMIT_RUNNING_DISPARITY 0x1000 +#define TBI_CONTROL_2_DISABLE_RECEIVE_RUNNING_DISPARITY 0x2000 +#define TBI_CONTROL_2_SHORTCUT_LINK_TIMER 0x4000 +#define TBI_CONTROL_2_SOFT_RESET 0x8000 /* marvel specific */ -#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */ -#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */ -#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */ +#define MV1111_EXT_CTRL1_REG 16 /* PHY Specific Control Reg */ +#define MV1111_SPEC_STAT_REG 17 /* PHY Specific Status Reg */ +#define MV1111_EXT_CTRL2_REG 20 /* Extended PHY Specific Control Reg */ /* * MARVELL 88E1111 PHY register bit masks */ /* PHY Specific Status Register (MV1111_EXT_CTRL1_REG) */ -#define SPEC_STAT_SPEED_MASK (3 << 14) -#define SPEC_STAT_FULL_DUP (1 << 13) -#define SPEC_STAT_PAGE_RCVD (1 << 12) -#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */ -#define SPEC_STAT_LINK_UP (1 << 10) -#define SPEC_STAT_CABLE_LEN_MASK (7 << 7) /* Cable Length (100/1000 modes only) */ -#define SPEC_STAT_MDIX (1 << 6) -#define SPEC_STAT_POLARITY (1 << 1) -#define SPEC_STAT_JABBER (1 << 0) +#define SPEC_STAT_SPEED_MASK (3 << 14) +#define SPEC_STAT_FULL_DUP (1 << 13) +#define SPEC_STAT_PAGE_RCVD (1 << 12) +#define SPEC_STAT_RESOLVED (1 << 11) /* Speed and Duplex Resolved */ +#define SPEC_STAT_LINK_UP (1 << 10) +#define SPEC_STAT_CABLE_LEN_MASK (7 << 7)/* Cable Length (100/1000 modes only) */ +#define SPEC_STAT_MDIX (1 << 6) +#define SPEC_STAT_POLARITY (1 << 1) +#define SPEC_STAT_JABBER (1 << 0) -#define SPEED_1000 (2 << 14) -#define SPEED_100 (1 << 14) -#define SPEED_10 (0 << 14) +#define SPEED_1000 (2 << 14) +#define SPEED_100 (1 << 14) +#define SPEED_10 (0 << 14) -#define TBI_ADDR 0x1E /* Ten Bit Interface address */ +#define TBI_ADDR 0x1E /* Ten Bit Interface address */ /* negotiated link parameters */ -#define LINK_SPEED_UNKNOWN 0 -#define LINK_SPEED_10 1 -#define LINK_SPEED_100 2 -#define LINK_SPEED_1000 3 +#define LINK_SPEED_UNKNOWN 0 +#define LINK_SPEED_10 1 +#define LINK_SPEED_100 2 +#define LINK_SPEED_1000 3 -#define LINK_DUPLEX_UNKNOWN 0 -#define LINK_DUPLEX_HALF 1 -#define LINK_DUPLEX_FULL 2 +#define LINK_DUPLEX_UNKNOWN 0 +#define LINK_DUPLEX_HALF 1 +#define LINK_DUPLEX_FULL 2 static unsigned int phy_address[] = { 8, 9 }; @@ -390,56 +392,56 @@ struct dma_descriptor { }; /* last next descriptor address flag */ -#define DMA_DESCR_LAST (1 << 31) +#define DMA_DESCR_LAST (1 << 31) /* TX DMA descriptor config status bits */ -#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */ -#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */ -#define DMA_DESCR_TX_PFVLAN (1 << 2) -#define DMA_DESCR_TX_HUGE (1 << 3) -#define DMA_DESCR_TX_PAD (1 << 4) -#define DMA_DESCR_TX_CRC (1 << 5) -#define DMA_DESCR_TX_DESCR_INT (1 << 14) -#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000 -#define DMA_DESCR_TX_ONE_COLLISION (1 << 20) -#define DMA_DESCR_TX_LATE_COLLISION (1 << 24) -#define DMA_DESCR_TX_UNDERRUN (1 << 25) -#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26) -#define DMA_DESCR_TX_OK (1 << 30) -#define DMA_DESCR_TX_OWNER (1 << 31) +#define DMA_DESCR_TX_EOF (1 << 0) /* end of frame */ +#define DMA_DESCR_TX_SOF (1 << 1) /* start of frame */ +#define DMA_DESCR_TX_PFVLAN (1 << 2) +#define DMA_DESCR_TX_HUGE (1 << 3) +#define DMA_DESCR_TX_PAD (1 << 4) +#define DMA_DESCR_TX_CRC (1 << 5) +#define DMA_DESCR_TX_DESCR_INT (1 << 14) +#define DMA_DESCR_TX_RETRY_COUNT 0x000F0000 +#define DMA_DESCR_TX_ONE_COLLISION (1 << 20) +#define DMA_DESCR_TX_LATE_COLLISION (1 << 24) +#define DMA_DESCR_TX_UNDERRUN (1 << 25) +#define DMA_DESCR_TX_RETRY_LIMIT (1 << 26) +#define DMA_DESCR_TX_OK (1 << 30) +#define DMA_DESCR_TX_OWNER (1 << 31) /* RX DMA descriptor status bits */ -#define DMA_DESCR_RX_EOF (1 << 0) -#define DMA_DESCR_RX_SOF (1 << 1) -#define DMA_DESCR_RX_VTF (1 << 2) -#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3) -#define DMA_DESCR_RX_SHORT_FRAME (1 << 4) -#define DMA_DESCR_RX_HASH_MATCH (1 << 7) -#define DMA_DESCR_RX_BAD_FRAME (1 << 8) -#define DMA_DESCR_RX_OVERRUN (1 << 9) -#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11) -#define DMA_DESCR_RX_CRC_ERROR (1 << 12) -#define DMA_DESCR_RX_DESCR_INT (1 << 13) -#define DMA_DESCR_RX_OWNER (1 << 15) - -#define RX_BUFFER_SIZE PKTSIZE -#define NUM_RX_DESC PKTBUFSRX +#define DMA_DESCR_RX_EOF (1 << 0) +#define DMA_DESCR_RX_SOF (1 << 1) +#define DMA_DESCR_RX_VTF (1 << 2) +#define DMA_DESCR_RX_FRAME_IS_TYPE (1 << 3) +#define DMA_DESCR_RX_SHORT_FRAME (1 << 4) +#define DMA_DESCR_RX_HASH_MATCH (1 << 7) +#define DMA_DESCR_RX_BAD_FRAME (1 << 8) +#define DMA_DESCR_RX_OVERRUN (1 << 9) +#define DMA_DESCR_RX_MAX_FRAME_LEN (1 << 11) +#define DMA_DESCR_RX_CRC_ERROR (1 << 12) +#define DMA_DESCR_RX_DESCR_INT (1 << 13) +#define DMA_DESCR_RX_OWNER (1 << 15) + +#define RX_BUFFER_SIZE PKTSIZE +#define NUM_RX_DESC PKTBUFSRX static struct dma_descriptor tx_descriptor __attribute__ ((aligned(32))); static struct dma_descriptor rx_descr_array[NUM_RX_DESC] - __attribute__ ((aligned(32))); + __attribute__ ((aligned(32))); static struct dma_descriptor *rx_descr_current; -static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis); -static int tsi108_eth_send(struct eth_device *dev, +static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis); +static int tsi108_eth_send (struct eth_device *dev, volatile void *packet, int length); -static int tsi108_eth_recv(struct eth_device *dev); -static void tsi108_eth_halt(struct eth_device *dev); -static unsigned int read_phy(unsigned int base, +static int tsi108_eth_recv (struct eth_device *dev); +static void tsi108_eth_halt (struct eth_device *dev); +static unsigned int read_phy (unsigned int base, unsigned int phy_addr, unsigned int phy_reg); -static void write_phy(unsigned int base, +static void write_phy (unsigned int base, unsigned int phy_addr, unsigned int phy_reg, unsigned int phy_data); @@ -447,15 +449,15 @@ static void write_phy(unsigned int base, /* * print phy debug infomation */ -static void dump_phy_regs(unsigned int phy_addr) +static void dump_phy_regs (unsigned int phy_addr) { int i; - printf("PHY %d registers\n", phy_addr); + printf ("PHY %d registers\n", phy_addr); for (i = 0; i <= 30; i++) { - printf("%2d 0x%04x\n", i, read_phy(ETH_BASE, phy_addr, i)); + printf ("%2d 0x%04x\n", i, read_phy (ETH_BASE, phy_addr, i)); } - printf("\n"); + printf ("\n"); } #else @@ -466,27 +468,27 @@ static void dump_phy_regs(unsigned int phy_addr) /* * print debug infomation */ -static void tx_diag_regs(unsigned int base) +static void tx_diag_regs (unsigned int base) { int i; unsigned long dummy; - printf("TX diagnostics registers\n"); + printf ("TX diagnostics registers\n"); reg_TX_DIAGNOSTIC_ADDR(base) = 0x00 | TX_DIAGNOSTIC_ADDR_AI; - udelay(1000); + udelay (1000); dummy = reg_TX_DIAGNOSTIC_DATA(base); for (i = 0x00; i <= 0x05; i++) { - udelay(1000); - printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); + udelay (1000); + printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); } reg_TX_DIAGNOSTIC_ADDR(base) = 0x40 | TX_DIAGNOSTIC_ADDR_AI; - udelay(1000); + udelay (1000); dummy = reg_TX_DIAGNOSTIC_DATA(base); for (i = 0x40; i <= 0x47; i++) { - udelay(1000); - printf("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); + udelay (1000); + printf ("0x%02x 0x%08x\n", i, reg_TX_DIAGNOSTIC_DATA(base)); } - printf("\n"); + printf ("\n"); } #else @@ -497,27 +499,27 @@ static void tx_diag_regs(unsigned int base) /* * print debug infomation */ -static void rx_diag_regs(unsigned int base) +static void rx_diag_regs (unsigned int base) { int i; unsigned long dummy; - printf("RX diagnostics registers\n"); + printf ("RX diagnostics registers\n"); reg_RX_DIAGNOSTIC_ADDR(base) = 0x00 | RX_DIAGNOSTIC_ADDR_AI; - udelay(1000); + udelay (1000); dummy = reg_RX_DIAGNOSTIC_DATA(base); for (i = 0x00; i <= 0x05; i++) { - udelay(1000); - printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); + udelay (1000); + printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); } reg_RX_DIAGNOSTIC_ADDR(base) = 0x40 | RX_DIAGNOSTIC_ADDR_AI; - udelay(1000); + udelay (1000); dummy = reg_RX_DIAGNOSTIC_DATA(base); for (i = 0x08; i <= 0x0a; i++) { - udelay(1000); - printf("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); + udelay (1000); + printf ("0x%02x 0x%08x\n", i, reg_RX_DIAGNOSTIC_DATA(base)); } - printf("\n"); + printf ("\n"); } #else @@ -528,15 +530,15 @@ static void rx_diag_regs(unsigned int base) /* * print debug infomation */ -static void debug_mii_regs(unsigned int base) +static void debug_mii_regs (unsigned int base) { - printf("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base)); - printf("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base)); - printf("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base)); - printf("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base)); - printf("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base)); - printf("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base)); - printf("\n"); + printf ("MII_MGMT_CONFIG 0x%08x\n", reg_MII_MGMT_CONFIG(base)); + printf ("MII_MGMT_COMMAND 0x%08x\n", reg_MII_MGMT_COMMAND(base)); + printf ("MII_MGMT_ADDRESS 0x%08x\n", reg_MII_MGMT_ADDRESS(base)); + printf ("MII_MGMT_CONTROL 0x%08x\n", reg_MII_MGMT_CONTROL(base)); + printf ("MII_MGMT_STATUS 0x%08x\n", reg_MII_MGMT_STATUS(base)); + printf ("MII_MGMT_INDICATORS 0x%08x\n", reg_MII_MGMT_INDICATORS(base)); + printf ("\n"); } #else @@ -546,15 +548,15 @@ static void debug_mii_regs(unsigned int base) /* * Wait until the phy bus is non-busy */ -static void phy_wait(unsigned int base, unsigned int condition) +static void phy_wait (unsigned int base, unsigned int condition) { int timeout; timeout = 0; while (reg_MII_MGMT_INDICATORS(base) & condition) { - udelay(10); + udelay (10); if (++timeout > 10000) { - printf("ERROR: timeout waiting for phy bus (%d)\n", + printf ("ERROR: timeout waiting for phy bus (%d)\n", condition); break; } @@ -564,12 +566,12 @@ static void phy_wait(unsigned int base, unsigned int condition) /* * read phy register */ -static unsigned int read_phy(unsigned int base, +static unsigned int read_phy (unsigned int base, unsigned int phy_addr, unsigned int phy_reg) { unsigned int value; - phy_wait(base, MII_MGMT_INDICATORS_BUSY); + phy_wait (base, MII_MGMT_INDICATORS_BUSY); reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg; @@ -580,7 +582,7 @@ static unsigned int read_phy(unsigned int base, reg_MII_MGMT_COMMAND(base) = MII_MGMT_COMMAND_READ_CYCLE; /* wait for the read to complete */ - phy_wait(base, + phy_wait (base, MII_MGMT_INDICATORS_NOT_VALID | MII_MGMT_INDICATORS_BUSY); value = reg_MII_MGMT_STATUS(base); @@ -593,11 +595,11 @@ static unsigned int read_phy(unsigned int base, /* * write phy register */ -static void write_phy(unsigned int base, +static void write_phy (unsigned int base, unsigned int phy_addr, unsigned int phy_reg, unsigned int phy_data) { - phy_wait(base, MII_MGMT_INDICATORS_BUSY); + phy_wait (base, MII_MGMT_INDICATORS_BUSY); reg_MII_MGMT_ADDRESS(base) = (phy_addr << 8) | phy_reg; @@ -611,7 +613,7 @@ static void write_phy(unsigned int base, /* * configure the marvell 88e1111 phy */ -static int marvell_88e_phy_config(struct eth_device *dev, int *speed, +static int marvell_88e_phy_config (struct eth_device *dev, int *speed, int *duplex) { unsigned long base; @@ -630,40 +632,39 @@ static int marvell_88e_phy_config(struct eth_device *dev, int *speed, phy_addr = (unsigned long)dev->priv; /* Take the PHY out of reset. */ - write_phy(ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET); + write_phy (ETH_BASE, phy_addr, PHY_CTRL_REG, PHY_CTRL_RESET); /* Wait for the reset process to complete. */ - udelay(10); + udelay (10); timeout = 0; while ((phy_status = - read_phy(ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) { - udelay(10); + read_phy (ETH_BASE, phy_addr, PHY_CTRL_REG)) & PHY_CTRL_RESET) { + udelay (10); if (++timeout > 10000) { - printf("ERROR: timeout waiting for phy reset\n"); + printf ("ERROR: timeout waiting for phy reset\n"); break; } } /* TBI Configuration. */ - write_phy(base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE | + write_phy (base, TBI_ADDR, TBI_CONTROL_2, TBI_CONTROL_2_G_MII_MODE | TBI_CONTROL_2_RECEIVE_CLOCK_SELECT); /* Wait for the link to be established. */ timeout = 0; do { - udelay(20000); - phy_status = read_phy(ETH_BASE, phy_addr, PHY_STATUS_REG); + udelay (20000); + phy_status = read_phy (ETH_BASE, phy_addr, PHY_STATUS_REG); if (++timeout > 100) { debug_lev(1, "ERROR: unable to establish link!!!\n"); break; } } while ((phy_status & PHY_STAT_LINK_UP) == 0); - if ((phy_status & PHY_STAT_LINK_UP) == 0) { + if ((phy_status & PHY_STAT_LINK_UP) == 0) return 0; - } value = 0; - phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); + phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); if (phy_spec_status & SPEC_STAT_RESOLVED) { switch (phy_spec_status & SPEC_STAT_SPEED_MASK) { case SPEED_1000: @@ -681,45 +682,41 @@ static int marvell_88e_phy_config(struct eth_device *dev, int *speed, if (phy_spec_status & SPEC_STAT_FULL_DUP) { phy_duplex = LINK_DUPLEX_FULL; value |= PHY_CTRL_FULL_DUPLEX; - } else { + } else phy_duplex = LINK_DUPLEX_HALF; - } } /* set TBI speed */ - write_phy(base, TBI_ADDR, PHY_CTRL_REG, value); - write_phy(base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060); + write_phy (base, TBI_ADDR, PHY_CTRL_REG, value); + write_phy (base, TBI_ADDR, PHY_AN_ADV_REG, 0x0060); #if TSI108_ETH_DEBUG > 0 - printf("%s link is up", dev->name); - phy_spec_status = read_phy(ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); + printf ("%s link is up", dev->name); + phy_spec_status = read_phy (ETH_BASE, phy_addr, MV1111_SPEC_STAT_REG); if (phy_spec_status & SPEC_STAT_RESOLVED) { switch (phy_speed) { case LINK_SPEED_1000: - printf(", 1000 Mbps"); + printf (", 1000 Mbps"); break; case LINK_SPEED_100: - printf(", 100 Mbps"); + printf (", 100 Mbps"); break; case LINK_SPEED_10: - printf(", 10 Mbps"); + printf (", 10 Mbps"); break; } - if (phy_duplex == LINK_DUPLEX_FULL) { - printf(", Full duplex"); - } else { - printf(", Half duplex"); - } + if (phy_duplex == LINK_DUPLEX_FULL) + printf (", Full duplex"); + else + printf (", Half duplex"); } - printf("\n"); + printf ("\n"); #endif - dump_phy_regs(TBI_ADDR); - if (speed) { + dump_phy_regs (TBI_ADDR); + if (speed) *speed = phy_speed; - } - if (duplex) { + if (duplex) *duplex = phy_duplex; - } return 1; } @@ -729,7 +726,7 @@ static int marvell_88e_phy_config(struct eth_device *dev, int *speed, * * register the tsi108 ethernet controllers with the multi-ethernet system */ -int tsi108_eth_initialize(bd_t * bis) +int tsi108_eth_initialize (bd_t * bis) { struct eth_device *dev; int index; @@ -737,7 +734,7 @@ int tsi108_eth_initialize(bd_t * bis) for (index = 0; index < CONFIG_TSI108_ETH_NUM_PORTS; index++) { dev = (struct eth_device *)malloc(sizeof(struct eth_device)); - sprintf(dev->name, "TSI108_eth%d", index); + sprintf (dev->name, "TSI108_eth%d", index); dev->iobase = ETH_BASE + (index * ETH_PORT_OFFSET); dev->priv = (void *)(phy_address[index]); @@ -754,7 +751,7 @@ int tsi108_eth_initialize(bd_t * bis) /* * probe for and initialize a single ethernet interface */ -static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis) +static int tsi108_eth_probe (struct eth_device *dev, bd_t * bis) { unsigned long base; unsigned long value; @@ -794,25 +791,23 @@ static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis) reg_STATION_ADDRESS_2(base) = (dev->enetaddr[1] << 24) | (dev->enetaddr[0] << 16); - if (marvell_88e_phy_config(dev, &speed, &duplex) == 0) { + if (marvell_88e_phy_config(dev, &speed, &duplex) == 0) return 0; - } value = MAC_CONFIG_2_PREAMBLE_LENGTH(7) | MAC_CONFIG_2_PAD_CRC | MAC_CONFIG_2_CRC_ENABLE; - if (speed == LINK_SPEED_1000) { + if (speed == LINK_SPEED_1000) value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_BYTE); - } else { + else { value |= MAC_CONFIG_2_INTERFACE_MODE(INTERFACE_MODE_NIBBLE); reg_PORT_CONTROL(base) |= PORT_CONTROL_SPD; } if (duplex == LINK_DUPLEX_FULL) { value |= MAC_CONFIG_2_FULL_DUPLEX; reg_PORT_CONTROL(base) &= ~PORT_CONTROL_BPT; - } else { + } else reg_PORT_CONTROL(base) |= PORT_CONTROL_BPT; - } reg_MAC_CONFIG_2(base) = value; reg_RX_CONFIG(base) = RX_CONFIG_SE; @@ -875,7 +870,7 @@ static int tsi108_eth_probe(struct eth_device *dev, bd_t * bis) /* * send a packet */ -static int tsi108_eth_send(struct eth_device *dev, +static int tsi108_eth_send (struct eth_device *dev, volatile void *packet, int length) { unsigned long base; @@ -894,9 +889,8 @@ static int tsi108_eth_send(struct eth_device *dev, (unsigned long)tx_descr + sizeof(struct dma_descriptor)); - if (timeout != 0) { - udelay(15); - } + if (timeout != 0) + udelay (15); if (++timeout > 10000) { tx_diag_regs(base); debug_lev(1, @@ -908,7 +902,7 @@ static int tsi108_eth_send(struct eth_device *dev, status = le32_to_cpu(tx_descr->config_status); if ((status & DMA_DESCR_TX_OK) == 0) { #ifdef TX_PRINT_ERRORS - printf("TX packet error: 0x%08x\n %s%s%s%s\n", status, + printf ("TX packet error: 0x%08x\n %s%s%s%s\n", status, status & DMA_DESCR_TX_OK ? "tx error, " : "", status & DMA_DESCR_TX_RETRY_LIMIT ? "retry limit reached, " : "", @@ -918,7 +912,7 @@ static int tsi108_eth_send(struct eth_device *dev, #endif } - debug_lev(9, "sending packet %d\n", length); + debug_lev (9, "sending packet %d\n", length); tx_descr->start_addr0 = cpu_to_le32((vuint32) packet); tx_descr->start_addr1 = 0; tx_descr->next_descr_addr0 = 0; @@ -946,7 +940,7 @@ static int tsi108_eth_send(struct eth_device *dev, /* * Check for received packets and send them up the protocal stack */ -static int tsi108_eth_recv(struct eth_device *dev) +static int tsi108_eth_recv (struct eth_device *dev) { struct dma_descriptor *rx_descr; unsigned long base; @@ -957,7 +951,7 @@ static int tsi108_eth_recv(struct eth_device *dev) base = dev->iobase; /* make sure we see the changes made by the DMA engine */ - invalidate_dcache_range((unsigned long)rx_descr_array, + invalidate_dcache_range ((unsigned long)rx_descr_array, (unsigned long)rx_descr_array + sizeof(rx_descr_array)); @@ -968,7 +962,7 @@ static int tsi108_eth_recv(struct eth_device *dev) status = le32_to_cpu(rx_descr->config_status); if (status & DMA_DESCR_RX_BAD_FRAME) { #ifdef RX_PRINT_ERRORS - printf("RX packet error: 0x%08x\n %s%s%s%s%s%s\n", + printf ("RX packet error: 0x%08x\n %s%s%s%s%s%s\n", status, status & DMA_DESCR_RX_FRAME_IS_TYPE ? "too big, " : "", @@ -989,24 +983,23 @@ static int tsi108_eth_recv(struct eth_device *dev) /*** process packet ***/ buffer = (volatile uchar - *)(le32_to_cpu(rx_descr->start_addr0)); - NetReceive(buffer, length); + *)(le32_to_cpu (rx_descr->start_addr0)); + NetReceive (buffer, length); - invalidate_dcache_range((unsigned long)buffer, + invalidate_dcache_range ((unsigned long)buffer, (unsigned long)buffer + RX_BUFFER_SIZE); } /* Give this buffer back to the DMA engine */ rx_descr->vlan_byte_count = 0; - rx_descr->config_status = cpu_to_le32((RX_BUFFER_SIZE << 16) | + rx_descr->config_status = cpu_to_le32 ((RX_BUFFER_SIZE << 16) | DMA_DESCR_RX_OWNER); /* move descriptor pointer forward */ rx_descr = (struct dma_descriptor - *)(le32_to_cpu(rx_descr->next_descr_addr0)); - if (rx_descr == 0) { + *)(le32_to_cpu (rx_descr->next_descr_addr0)); + if (rx_descr == 0) rx_descr = &rx_descr_array[0]; - } } /* remember where we are for next time */ rx_descr_current = rx_descr; @@ -1026,7 +1019,7 @@ static int tsi108_eth_recv(struct eth_device *dev) /* * disable an ethernet interface */ -static void tsi108_eth_halt(struct eth_device *dev) +static void tsi108_eth_halt (struct eth_device *dev) { unsigned long base; diff --git a/drivers/tsi108_i2c.c b/drivers/tsi108_i2c.c index 08e5e3b4f55..c100cb82470 100644 --- a/drivers/tsi108_i2c.c +++ b/drivers/tsi108_i2c.c @@ -23,19 +23,18 @@ */ #include +#include #ifdef CONFIG_TSI108_I2C - -#include #include #if (CONFIG_COMMANDS & CFG_CMD_I2C) -#define I2C_DELAY 100000 +#define I2C_DELAY 100000 #undef DEBUG_I2C #ifdef DEBUG_I2C -#define DPRINT(x) printf(x) +#define DPRINT(x) printf (x) #else #define DPRINT(x) #endif @@ -43,7 +42,7 @@ /* All functions assume that Tsi108 I2C block is the only master on the bus */ /* I2C read helper function */ -static int i2c_read_byte( +static int i2c_read_byte ( uint i2c_chan, /* I2C channel number: 0 - main, 1 - SDC SPD */ uchar chip_addr,/* I2C device address on the bus */ uint byte_addr, /* Byte address within I2C device */ @@ -55,19 +54,17 @@ static int i2c_read_byte( u32 op_status = TSI108_I2C_TIMEOUT_ERR; u32 chan_offset = TSI108_I2C_OFFSET; - DPRINT(("I2C read_byte() %d 0x%02x 0x%02x\n", + DPRINT (("I2C read_byte() %d 0x%02x 0x%02x\n", i2c_chan, chip_addr, byte_addr)); - if (0 != i2c_chan) { + if (0 != i2c_chan) chan_offset = TSI108_I2C_SDRAM_OFFSET; - } /* Check if I2C operation is in progress */ temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2); if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | - I2C_CNTRL2_START)) - ) { + I2C_CNTRL2_START))) { /* Set device address and operation (read = 0) */ temp = (byte_addr << 16) | ((chip_addr & 0x07) << 8) | ((chip_addr >> 3) & 0x0F); @@ -75,7 +72,7 @@ static int i2c_read_byte( temp; /* Issue the read command - * (at this moment all other parameters are 0 + * (at this moment all other parameters are 0 * (size = 1 byte, lane = 0) */ @@ -108,7 +105,7 @@ static int i2c_read_byte( /* report HW error */ op_status = TSI108_I2C_IF_ERROR; - DPRINT(("I2C HW error reported: 0x%02x\n", temp)); + DPRINT (("I2C HW error reported: 0x%02x\n", temp)); } break; @@ -117,20 +114,20 @@ static int i2c_read_byte( } else { op_status = TSI108_I2C_IF_BUSY; - DPRINT(("I2C Transaction start failed: 0x%02x\n", temp)); + DPRINT (("I2C Transaction start failed: 0x%02x\n", temp)); } - DPRINT(("I2C read_byte() status: 0x%02x\n", op_status)); + DPRINT (("I2C read_byte() status: 0x%02x\n", op_status)); return op_status; } -/* +/* * I2C Read interface as defined in "include/i2c.h" : * chip_addr: I2C chip address, range 0..127 * (to read from SPD channel EEPROM use (0xD0 ... 0xD7) * NOTE: The bit 7 in the chip_addr serves as a channel select. * This hack is for enabling "isdram" command on Tsi108 boards - * without changes to common code. Used for I2C reads only. + * without changes to common code. Used for I2C reads only. * byte_addr: Memory or register address within the chip * alen: Number of bytes to use for addr (typically 1, 2 for larger * memories, 0 for register type devices with only one @@ -141,7 +138,8 @@ static int i2c_read_byte( * Returns: 0 on success, not 0 on failure */ -int i2c_read(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, int len) +int i2c_read (uchar chip_addr, uint byte_addr, int alen, + uchar * buffer, int len) { u32 op_status = TSI108_I2C_PARAM_ERR; u32 i2c_if = 0; @@ -159,20 +157,20 @@ int i2c_read(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, int len) buffer++); if (TSI108_I2C_SUCCESS != op_status) { - DPRINT(("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len)); + DPRINT (("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len)); break; } } } - DPRINT(("I2C read() status: 0x%02x\n", op_status)); + DPRINT (("I2C read() status: 0x%02x\n", op_status)); return op_status; } /* I2C write helper function */ -static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ +static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ uint byte_addr, /* Byte address within I2C device */ uchar * buffer /* pointer to data buffer */ ) @@ -210,7 +208,7 @@ static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ /* Wait until operation completed */ do { - // Read I2C operation status + /* Read I2C operation status */ temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); @@ -227,7 +225,7 @@ static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ /* report detected HW error */ op_status = TSI108_I2C_IF_ERROR; - DPRINT(("I2C HW error reported: 0x%02x\n", temp)); + DPRINT (("I2C HW error reported: 0x%02x\n", temp)); } break; @@ -237,13 +235,13 @@ static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ } else { op_status = TSI108_I2C_IF_BUSY; - DPRINT(("I2C Transaction start failed: 0x%02x\n", temp)); + DPRINT (("I2C Transaction start failed: 0x%02x\n", temp)); } return op_status; } -/* +/* * I2C Write interface as defined in "include/i2c.h" : * chip_addr: I2C chip address, range 0..127 * byte_addr: Memory or register address within the chip @@ -256,7 +254,7 @@ static int i2c_write_byte(uchar chip_addr,/* I2C device address on the bus */ * Returns: 0 on success, not 0 on failure */ -int i2c_write(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, +int i2c_write (uchar chip_addr, uint byte_addr, int alen, uchar * buffer, int len) { u32 op_status = TSI108_I2C_PARAM_ERR; @@ -265,10 +263,10 @@ int i2c_write(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) { while (len--) { op_status = - i2c_write_byte(chip_addr, byte_addr++, buffer++); + i2c_write_byte (chip_addr, byte_addr++, buffer++); if (TSI108_I2C_SUCCESS != op_status) { - DPRINT(("I2C write_byte() failed: 0x%02x (%d left)\n", op_status, len)); + DPRINT (("I2C write_byte() failed: 0x%02x (%d left)\n", op_status, len)); break; } @@ -278,13 +276,13 @@ int i2c_write(uchar chip_addr, uint byte_addr, int alen, uchar * buffer, return op_status; } -/* +/* * I2C interface function as defined in "include/i2c.h". * Probe the given I2C chip address by reading single byte from offset 0. * Returns 0 if a chip responded, not 0 on failure. */ -int i2c_probe(uchar chip) +int i2c_probe (uchar chip) { u32 tmp; @@ -293,8 +291,8 @@ int i2c_probe(uchar chip) * The Tsi108 HW doesn't support sending just the chip address * and checkong for an back. */ - return i2c_read(chip, 0, 1, (char *)&tmp, 1); + return i2c_read (chip, 0, 1, (char *)&tmp, 1); } -#endif /* (CONFIG_COMMANDS & CFG_CMD_I2C) */ +#endif /* (CONFIG_COMMANDS & CFG_CMD_I2C) */ #endif /* CONFIG_TSI108_I2C */ diff --git a/drivers/tsi108_pci.c b/drivers/tsi108_pci.c index f374ede6620..9f606df5180 100644 --- a/drivers/tsi108_pci.c +++ b/drivers/tsi108_pci.c @@ -36,7 +36,7 @@ struct pci_controller local_hose; -void tsi108_clear_pci_error(void) +void tsi108_clear_pci_error (void) { u32 err_stat, err_addr, pci_stat; @@ -79,11 +79,11 @@ void tsi108_clear_pci_error(void) return; } -unsigned int __get_pci_config_dword(u32 addr) +unsigned int __get_pci_config_dword (u32 addr) { unsigned int retval; - __asm__ __volatile__(" lwbrx %0,0,%1\n" + __asm__ __volatile__ (" lwbrx %0,0,%1\n" "1: eieio\n" "2:\n" ".section .fixup,\"ax\"\n" @@ -97,53 +97,53 @@ unsigned int __get_pci_config_dword(u32 addr) return (retval); } -static int tsi108_read_config_dword(struct pci_controller *hose, +static int tsi108_read_config_dword (struct pci_controller *hose, pci_dev_t dev, int offset, u32 * value) { dev &= (CFG_PCI_CFG_SIZE - 1); dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc)); *value = __get_pci_config_dword(dev); if (0xFFFFFFFF == *value) - tsi108_clear_pci_error(); + tsi108_clear_pci_error (); return 0; } -static int tsi108_write_config_dword(struct pci_controller *hose, +static int tsi108_write_config_dword (struct pci_controller *hose, pci_dev_t dev, int offset, u32 value) { dev &= (CFG_PCI_CFG_SIZE - 1); dev |= (CFG_PCI_CFG_BASE | (offset & 0xfc)); - out_le32((volatile unsigned *)dev, value); + out_le32 ((volatile unsigned *)dev, value); return 0; } -void pci_init_board(void) +void pci_init_board (void) { struct pci_controller *hose = (struct pci_controller *)&local_hose; hose->first_busno = 0; hose->last_busno = 0xff; - pci_set_region(hose->regions + 0, + pci_set_region (hose->regions + 0, CFG_PCI_MEMORY_BUS, CFG_PCI_MEMORY_PHYS, CFG_PCI_MEMORY_SIZE, PCI_REGION_MEM | PCI_REGION_MEMORY); /* PCI memory space */ - pci_set_region(hose->regions + 1, + pci_set_region (hose->regions + 1, CFG_PCI_MEM_BUS, CFG_PCI_MEM_PHYS, CFG_PCI_MEM_SIZE, PCI_REGION_MEM); /* PCI I/O space */ - pci_set_region(hose->regions + 2, + pci_set_region (hose->regions + 2, CFG_PCI_IO_BUS, CFG_PCI_IO_PHYS, CFG_PCI_IO_SIZE, PCI_REGION_IO); hose->region_count = 3; - pci_set_ops(hose, + pci_set_ops (hose, pci_hose_read_config_byte_via_dword, pci_hose_read_config_word_via_dword, tsi108_read_config_dword, @@ -151,22 +151,22 @@ void pci_init_board(void) pci_hose_write_config_word_via_dword, tsi108_write_config_dword); - pci_register_hose(hose); + pci_register_hose (hose); - hose->last_busno = pci_hose_scan(hose); + hose->last_busno = pci_hose_scan (hose); - debug("Done PCI initialization\n"); + debug ("Done PCI initialization\n"); return; } #ifdef CONFIG_OF_FLAT_TREE void -ft_pci_setup(void *blob, bd_t *bd) +ft_pci_setup (void *blob, bd_t *bd) { u32 *p; int len; - p = (u32 *)ft_get_prop(blob, "/" OF_TSI "/pci@1000/bus-range", &len); + p = (u32 *)ft_get_prop (blob, "/" OF_TSI "/pci@1000/bus-range", &len); if (p != NULL) { p[0] = local_hose.first_busno; p[1] = local_hose.last_busno; diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h index 24cc86bebce..b13b699b593 100644 --- a/include/configs/mpc7448hpc2.h +++ b/include/configs/mpc7448hpc2.h @@ -24,12 +24,11 @@ * MA 02111-1307 USA */ -/**************************************************************** - * +/* * board specific configuration options for Freescale * MPC7448HPC2 (High-Performance Computing II) (Taiga) board * - ****************************************************************/ + */ #ifndef __CONFIG_H #define __CONFIG_H @@ -45,11 +44,11 @@ #define CONFIG_750FX /* this option to enable init of extended BATs */ #define CONFIG_ALTIVEC /* undef to disable */ -#define CFG_BOARD_NAME "MPC7448 HPC II" -#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II" +#define CFG_BOARD_NAME "MPC7448 HPC II" +#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II" -#define CFG_OCN_CLK 133000000 /* 133 MHz */ -#define CFG_CONFIG_BUS_CLK 133000000 +#define CFG_OCN_CLK 133000000 /* 133 MHz */ +#define CFG_CONFIG_BUS_CLK 133000000 #define CFG_CLK_SPREAD /* Enable Spread-Spectrum Clock generation */ @@ -63,10 +62,10 @@ /* Default MAC Addresses for on-chip GIGE Controller */ -#define CONFIG_ETHADDR 00:06:D2:00:00:01 +#define CONFIG_ETHADDR 00:06:D2:00:00:01 #define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:06:D2:00:00:02 +#define CONFIG_ETH1ADDR 00:06:D2:00:00:02 #define CONFIG_ENV_OVERWRITE @@ -75,12 +74,12 @@ * (easy to change) */ -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */ +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */ /*#define CFG_HUSH_PARSER */ #undef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CFG_PROMPT_HUSH_PS2 "> " /* Pass open firmware flat tree */ #define CONFIG_OF_FLAT_TREE 1 @@ -99,29 +98,30 @@ * for your console driver. * * what to do: - * If you have hacked a serial cable onto the second DUART channel, change the CFG_DUART port from 1 - * to 0 below. + * If you have hacked a serial cable onto the second DUART channel, + * change the CFG_DUART port from 1 to 0 below. * */ -#define CONFIG_CONS_INDEX 1 +#define CONFIG_CONS_INDEX 1 #define CFG_NS16550 #define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK CFG_OCN_CLK * 8 -#define CFG_NS16550_COM1 (CFG_TSI108_CSR_RST_BASE+0x7808) -#define CFG_NS16550_COM2 (CFG_TSI108_CSR_RST_BASE+0x7C08) +#define CFG_NS16550_COM1 (CFG_TSI108_CSR_RST_BASE+0x7808) +#define CFG_NS16550_COM2 (CFG_TSI108_CSR_RST_BASE+0x7C08) #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ #define CONFIG_ZERO_BOOTDELAY_CHECK #undef CONFIG_BOOTARGS -/*#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" */ +/* #define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" + * to mount root filesystem over NFS;echo" */ #if (CONFIG_BOOTDELAY >= 0) -#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\ +#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\ setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \ ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; " @@ -130,34 +130,34 @@ #undef CONFIG_EXTRA_ENV_SETTINGS -#define CONFIG_SERIAL "No. 1" +#define CONFIG_SERIAL "No. 1" /* Networking Configuration */ -#define KSEG1ADDR(a) (a) /* Needed by the rtl8139 driver */ +#define KSEG1ADDR(a) (a) /* Needed by the rtl8139 driver */ #define CONFIG_TSI108_ETH -#define CONFIG_TSI108_ETH_NUM_PORTS 2 +#define CONFIG_TSI108_ETH_NUM_PORTS 2 #define CONFIG_NET_MULTI -#define CONFIG_IPADDR 172.27.234.48 -#define CONFIG_SERVERIP 172.27.234.10 -#define CONFIG_NETMASK 255.255.0.0 -#define CONFIG_GATEWAYIP 172.27.255.254 +#define CONFIG_IPADDR 172.27.234.48 +#define CONFIG_SERVERIP 172.27.234.10 +#define CONFIG_NETMASK 255.255.0.0 +#define CONFIG_GATEWAYIP 172.27.255.254 -#define CONFIG_BOOTFILE zImage.initrd.elf -#define CONFIG_LOADADDR 0x400000 +#define CONFIG_BOOTFILE zImage.initrd.elf +#define CONFIG_LOADADDR 0x400000 /*-------------------------------------------------------------------------- */ -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ #define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */ #undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ - CONFIG_BOOTP_BOOTFILESIZE) +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE) #define CONFIG_COMMANDS (CONFIG_CMD_DFL \ | CFG_CMD_ASKENV \ @@ -178,59 +178,59 @@ /*set date in u-boot*/ #define CONFIG_RTC_M48T35A -#define CFG_NVRAM_BASE_ADDR 0xfc000000 -#define CFG_NVRAM_SIZE 0x8000 +#define CFG_NVRAM_BASE_ADDR 0xfc000000 +#define CFG_NVRAM_SIZE 0x8000 /* * Miscellaneous configurable options */ -#define CONFIG_VERSION_VARIABLE 1 +#define CONFIG_VERSION_VARIABLE 1 #define CONFIG_TSI108_I2C -#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)/* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ /* #define CFG_DRAM_TEST - * DRAM tests - * CFG_DRAM_TEST - enables the following tests. + * DRAM tests + * CFG_DRAM_TEST - enables the following tests. * - * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines - * Environment variable 'test_dram_data' must be - * set to 'y'. - * CFG_DRAM_TEST_ADDRESS - Enables test to verify that each word is uniquely - * addressable. Environment variable - * 'test_dram_address' must be set to 'y'. - * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test. - * This test takes about 6 minutes to test 64 MB. - * Environment variable 'test_dram_walk' must be - * set to 'y'. + * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines + * Environment variable 'test_dram_data' must be + * set to 'y'. + * CFG_DRAM_TEST_ADDRESS - Enables test to verify that each word + * is uniquely addressable. Environment variable + * 'test_dram_address' must be set to 'y'. + * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test. + * This test takes about 6 minutes to test 64 MB. + * Environment variable 'test_dram_walk' must be + * set to 'y'. */ #undef CFG_DRAM_TEST -#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */ +#define CFG_MEMTEST_START 0x00400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */ #if defined(CFG_DRAM_TEST) #define CFG_DRAM_TEST_DATA #define CFG_DRAM_TEST_ADDRESS #define CFG_DRAM_TEST_WALK -#endif /* CFG_DRAM_TEST */ +#endif /* CFG_DRAM_TEST */ -#define CFG_LOAD_ADDR 0x00400000 /* default load address */ +#define CFG_LOAD_ADDR 0x00400000 /* default load address */ -#define CFG_HZ 1000 /* decr freq: 1ms ticks */ +#define CFG_HZ 1000 /* decr freq: 1ms ticks */ /* * Low Level Configuration Settings @@ -246,12 +246,12 @@ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS * To an unused memory region. The stack will remain in cache until RAM * is initialized -*/ + */ #undef CFG_INIT_RAM_LOCK -#define CFG_INIT_RAM_ADDR 0x07d00000 /* unused memory region */ -#define CFG_INIT_RAM_END 0x4000 /* larger space - we have SDRAM initialized */ +#define CFG_INIT_RAM_ADDR 0x07d00000 /* unused memory region */ +#define CFG_INIT_RAM_END 0x4000/* larger space - we have SDRAM initialized */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */ +#define CFG_GBL_DATA_SIZE 128/* size in bytes reserved for init data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) /*----------------------------------------------------------------------- @@ -260,54 +260,54 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */ -#define CFG_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */ +#define CFG_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */ +#define CFG_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */ -#define CFG_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */ -#define CFG_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */ +#define CFG_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */ +#define CFG_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */ -#define CFG_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */ +#define CFG_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */ -#define CFG_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */ +#define CFG_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */ -#define CFG_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */ +#define CFG_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */ -#define CFG_FLASH_BASE 0xff000000 /* Base Address of Flash device */ -#define CFG_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */ +#define CFG_FLASH_BASE 0xff000000 /* Base Address of Flash device */ +#define CFG_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */ #define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS */ -#define PCI0_IO_BASE_BOOTM 0xfd000000 +#define PCI0_IO_BASE_BOOTM 0xfd000000 -#define CFG_RESET_ADDRESS 0x3fffff00 -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CFG_MONITOR_BASE TEXT_BASE /* u-boot code base */ -#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ +#define CFG_RESET_ADDRESS 0x3fffff00 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* u-boot code base */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ /* Peripheral Device section */ -/******************************************************* +/* * Resources on the Tsi108 - *******************************************************/ + */ -#define CFG_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */ -#define CFG_TSI108_CSR_BASE CFG_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */ +#define CFG_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */ +#define CFG_TSI108_CSR_BASE CFG_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */ #define ENABLE_PCI_CSR_BAR /* enables access to Tsi108 CSRs from the PCI/X bus */ #undef DISABLE_PBM -/*----------------------------------------------------------------------- +/* * PCI stuff - *----------------------------------------------------------------------- + * */ #define CONFIG_PCI /* include pci support */ #define CONFIG_TSI108_PCI /* include tsi108 pci support */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -315,20 +315,20 @@ /* PCI MEMORY MAP section */ /* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 /* PCI Memory Space */ -#define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS) -#define CFG_PCI_MEM_PHYS (CFG_PCI_MEM32_BASE) //CFG_PCI_MEM32_BASE = 0xE0000000 -#define CFG_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */ +#define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS) +#define CFG_PCI_MEM_PHYS (CFG_PCI_MEM32_BASE) /* 0xE0000000 */ +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */ /* PCI I/O Space */ -#define CFG_PCI_IO_BUS 0x00000000 -#define CFG_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */ +#define CFG_PCI_IO_BUS 0x00000000 +#define CFG_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */ -#define CFG_PCI_IO_SIZE 0x01000000 /* 16MB */ +#define CFG_PCI_IO_SIZE 0x01000000 /* 16MB */ #define _IO_BASE 0x00000000 /* points to PCI I/O space */ @@ -336,91 +336,91 @@ #define CFG_PCI_CFG_BASE 0xfb000000 /* Changed from FE000000 */ #define CFG_PCI_CFG_SIZE 0x01000000 /* 16MB */ -#define CFG_IBAT0U 0xFE0003FF -#define CFG_IBAT0L 0xFE000002 +#define CFG_IBAT0U 0xFE0003FF +#define CFG_IBAT0L 0xFE000002 -#define CFG_IBAT1U 0x00007FFF -#define CFG_IBAT1L 0x00000012 +#define CFG_IBAT1U 0x00007FFF +#define CFG_IBAT1L 0x00000012 -#define CFG_IBAT2U 0x80007FFF -#define CFG_IBAT2L 0x80000022 +#define CFG_IBAT2U 0x80007FFF +#define CFG_IBAT2L 0x80000022 -#define CFG_IBAT3U 0x00000000 -#define CFG_IBAT3L 0x00000000 +#define CFG_IBAT3U 0x00000000 +#define CFG_IBAT3L 0x00000000 -#define CFG_IBAT4U 0x00000000 -#define CFG_IBAT4L 0x00000000 +#define CFG_IBAT4U 0x00000000 +#define CFG_IBAT4L 0x00000000 -#define CFG_IBAT5U 0x00000000 -#define CFG_IBAT5L 0x00000000 +#define CFG_IBAT5U 0x00000000 +#define CFG_IBAT5L 0x00000000 -#define CFG_IBAT6U 0x00000000 -#define CFG_IBAT6L 0x00000000 +#define CFG_IBAT6U 0x00000000 +#define CFG_IBAT6L 0x00000000 -#define CFG_IBAT7U 0x00000000 -#define CFG_IBAT7L 0x00000000 +#define CFG_IBAT7U 0x00000000 +#define CFG_IBAT7L 0x00000000 -#define CFG_DBAT0U 0xE0003FFF -#define CFG_DBAT0L 0xE000002A +#define CFG_DBAT0U 0xE0003FFF +#define CFG_DBAT0L 0xE000002A -#define CFG_DBAT1U 0x00007FFF -#define CFG_DBAT1L 0x00000012 +#define CFG_DBAT1U 0x00007FFF +#define CFG_DBAT1L 0x00000012 -#define CFG_DBAT2U 0x00000000 -#define CFG_DBAT2L 0x00000000 +#define CFG_DBAT2U 0x00000000 +#define CFG_DBAT2L 0x00000000 -#define CFG_DBAT3U 0xC0000003 -#define CFG_DBAT3L 0xC000002A +#define CFG_DBAT3U 0xC0000003 +#define CFG_DBAT3L 0xC000002A -#define CFG_DBAT4U 0x00000000 -#define CFG_DBAT4L 0x00000000 +#define CFG_DBAT4U 0x00000000 +#define CFG_DBAT4L 0x00000000 -#define CFG_DBAT5U 0x00000000 -#define CFG_DBAT5L 0x00000000 +#define CFG_DBAT5U 0x00000000 +#define CFG_DBAT5L 0x00000000 -#define CFG_DBAT6U 0x00000000 -#define CFG_DBAT6L 0x00000000 +#define CFG_DBAT6U 0x00000000 +#define CFG_DBAT6L 0x00000000 -#define CFG_DBAT7U 0x00000000 -#define CFG_DBAT7L 0x00000000 +#define CFG_DBAT7U 0x00000000 +#define CFG_DBAT7L 0x00000000 /* I2C addresses for the two DIMM SPD chips */ -#define DIMM0_I2C_ADDR 0x51 -#define DIMM1_I2C_ADDR 0x52 +#define DIMM0_I2C_ADDR 0x51 +#define DIMM1_I2C_ADDR 0x52 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 1 /* Flash can be at one of two addresses */ -#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ +#define CFG_MAX_FLASH_BANKS 1/* Flash can be at one of two addresses */ +#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ #define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} #define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI #define CFG_FLASH_CFI_SWAP -#define PHYS_FLASH_SIZE 0x01000000 -#define CFG_MAX_FLASH_SECT (128) +#define PHYS_FLASH_SIZE 0x01000000 +#define CFG_MAX_FLASH_SECT (128) #define CFG_ENV_IS_IN_NVRAM -#define CFG_ENV_ADDR 0xFC000000 +#define CFG_ENV_ADDR 0xFC000000 -#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */ -#define CFG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */ +#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ +#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /*----------------------------------------------------------------------- @@ -429,16 +429,16 @@ */ #undef CFG_L2 -#define L2_INIT 0 -#define L2_ENABLE (L2_INIT | L2CR_L2E) +#define L2_INIT 0 +#define L2_ENABLE (L2_INIT | L2CR_L2E) /* * Internal Definitions * * Boot Flags */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CFG_EXCEPTION_AFTER_RELOCATE #define CFG_SERIAL_HANG_IN_EXCEPTION -#endif /* __CONFIG_H */ +#endif /* __CONFIG_H */ diff --git a/include/tsi108.h b/include/tsi108.h index 072daa03c3d..ba62e7abe60 100644 --- a/include/tsi108.h +++ b/include/tsi108.h @@ -31,191 +31,191 @@ #ifndef _TSI108_H_ #define _TSI108_H_ -#define TSI108_HLP_REG_OFFSET (0x0000) -#define TSI108_PCI_REG_OFFSET (0x1000) -#define TSI108_CLK_REG_OFFSET (0x2000) -#define TSI108_PB_REG_OFFSET (0x3000) -#define TSI108_SD_REG_OFFSET (0x4000) -#define TSI108_MPIC_REG_OFFSET (0x7400) - -#define PB_ID (0x000) -#define PB_RSR (0x004) -#define PB_BUS_MS_SELECT (0x008) -#define PB_ISR (0x00C) -#define PB_ARB_CTRL (0x018) -#define PB_PVT_CTRL2 (0x034) -#define PB_SCR (0x400) -#define PB_ERRCS (0x404) -#define PB_AERR (0x408) -#define PB_REG_BAR (0x410) -#define PB_OCN_BAR1 (0x414) -#define PB_OCN_BAR2 (0x418) -#define PB_SDRAM_BAR1 (0x41C) -#define PB_SDRAM_BAR2 (0x420) -#define PB_MCR (0xC00) -#define PB_MCMD (0xC04) - -#define HLP_B0_ADDR (0x000) -#define HLP_B1_ADDR (0x010) -#define HLP_B2_ADDR (0x020) -#define HLP_B3_ADDR (0x030) - -#define HLP_B0_MASK (0x004) -#define HLP_B1_MASK (0x014) -#define HLP_B2_MASK (0x024) -#define HLP_B3_MASK (0x034) - -#define HLP_B0_CTRL0 (0x008) -#define HLP_B1_CTRL0 (0x018) -#define HLP_B2_CTRL0 (0x028) -#define HLP_B3_CTRL0 (0x038) - -#define HLP_B0_CTRL1 (0x00C) -#define HLP_B1_CTRL1 (0x01C) -#define HLP_B2_CTRL1 (0x02C) -#define HLP_B3_CTRL1 (0x03C) - -#define PCI_CSR (0x004) -#define PCI_P2O_BAR0 (0x010) -#define PCI_P2O_BAR0_UPPER (0x014) -#define PCI_P2O_BAR2 (0x018) -#define PCI_P2O_BAR2_UPPER (0x01C) -#define PCI_P2O_BAR3 (0x020) -#define PCI_P2O_BAR3_UPPER (0x024) - -#define PCI_MISC_CSR (0x040) -#define PCI_P2O_PAGE_SIZES (0x04C) - -#define PCI_PCIX_STAT (0x0F4) - -#define PCI_IRP_STAT (0x184) - -#define PCI_PFAB_BAR0 (0x204) -#define PCI_PFAB_BAR0_UPPER (0x208) -#define PCI_PFAB_IO (0x20C) -#define PCI_PFAB_IO_UPPER (0x210) - -#define PCI_PFAB_MEM32 (0x214) -#define PCI_PFAB_MEM32_REMAP (0x218) -#define PCI_PFAB_MEM32_MASK (0x21C) - -#define CG_PLL0_CTRL0 (0x210) -#define CG_PLL0_CTRL1 (0x214) -#define CG_PLL1_CTRL0 (0x220) -#define CG_PLL1_CTRL1 (0x224) -#define CG_PWRUP_STATUS (0x234) +#define TSI108_HLP_REG_OFFSET (0x0000) +#define TSI108_PCI_REG_OFFSET (0x1000) +#define TSI108_CLK_REG_OFFSET (0x2000) +#define TSI108_PB_REG_OFFSET (0x3000) +#define TSI108_SD_REG_OFFSET (0x4000) +#define TSI108_MPIC_REG_OFFSET (0x7400) + +#define PB_ID (0x000) +#define PB_RSR (0x004) +#define PB_BUS_MS_SELECT (0x008) +#define PB_ISR (0x00C) +#define PB_ARB_CTRL (0x018) +#define PB_PVT_CTRL2 (0x034) +#define PB_SCR (0x400) +#define PB_ERRCS (0x404) +#define PB_AERR (0x408) +#define PB_REG_BAR (0x410) +#define PB_OCN_BAR1 (0x414) +#define PB_OCN_BAR2 (0x418) +#define PB_SDRAM_BAR1 (0x41C) +#define PB_SDRAM_BAR2 (0x420) +#define PB_MCR (0xC00) +#define PB_MCMD (0xC04) + +#define HLP_B0_ADDR (0x000) +#define HLP_B1_ADDR (0x010) +#define HLP_B2_ADDR (0x020) +#define HLP_B3_ADDR (0x030) + +#define HLP_B0_MASK (0x004) +#define HLP_B1_MASK (0x014) +#define HLP_B2_MASK (0x024) +#define HLP_B3_MASK (0x034) + +#define HLP_B0_CTRL0 (0x008) +#define HLP_B1_CTRL0 (0x018) +#define HLP_B2_CTRL0 (0x028) +#define HLP_B3_CTRL0 (0x038) + +#define HLP_B0_CTRL1 (0x00C) +#define HLP_B1_CTRL1 (0x01C) +#define HLP_B2_CTRL1 (0x02C) +#define HLP_B3_CTRL1 (0x03C) + +#define PCI_CSR (0x004) +#define PCI_P2O_BAR0 (0x010) +#define PCI_P2O_BAR0_UPPER (0x014) +#define PCI_P2O_BAR2 (0x018) +#define PCI_P2O_BAR2_UPPER (0x01C) +#define PCI_P2O_BAR3 (0x020) +#define PCI_P2O_BAR3_UPPER (0x024) + +#define PCI_MISC_CSR (0x040) +#define PCI_P2O_PAGE_SIZES (0x04C) + +#define PCI_PCIX_STAT (0x0F4) + +#define PCI_IRP_STAT (0x184) + +#define PCI_PFAB_BAR0 (0x204) +#define PCI_PFAB_BAR0_UPPER (0x208) +#define PCI_PFAB_IO (0x20C) +#define PCI_PFAB_IO_UPPER (0x210) + +#define PCI_PFAB_MEM32 (0x214) +#define PCI_PFAB_MEM32_REMAP (0x218) +#define PCI_PFAB_MEM32_MASK (0x21C) + +#define CG_PLL0_CTRL0 (0x210) +#define CG_PLL0_CTRL1 (0x214) +#define CG_PLL1_CTRL0 (0x220) +#define CG_PLL1_CTRL1 (0x224) +#define CG_PWRUP_STATUS (0x234) #define MPIC_CSR(n) (0x30C + (n * 0x40)) -#define SD_CTRL (0x000) -#define SD_STATUS (0x004) -#define SD_TIMING (0x008) -#define SD_REFRESH (0x00C) -#define SD_INT_STATUS (0x010) -#define SD_INT_ENABLE (0x014) -#define SD_INT_SET (0x018) -#define SD_D0_CTRL (0x020) -#define SD_D1_CTRL (0x024) -#define SD_D0_BAR (0x028) -#define SD_D1_BAR (0x02C) -#define SD_ECC_CTRL (0x040) -#define SD_DLL_STATUS (0x250) - -#define TS_SD_CTRL_ENABLE (1 << 31) - -#define PB_ERRCS_ES (1 << 1) -#define PB_ISR_PBS_RD_ERR (1 << 8) -#define PCI_IRP_STAT_P_CSR (1 << 23) - -/* +#define SD_CTRL (0x000) +#define SD_STATUS (0x004) +#define SD_TIMING (0x008) +#define SD_REFRESH (0x00C) +#define SD_INT_STATUS (0x010) +#define SD_INT_ENABLE (0x014) +#define SD_INT_SET (0x018) +#define SD_D0_CTRL (0x020) +#define SD_D1_CTRL (0x024) +#define SD_D0_BAR (0x028) +#define SD_D1_BAR (0x02C) +#define SD_ECC_CTRL (0x040) +#define SD_DLL_STATUS (0x250) + +#define TS_SD_CTRL_ENABLE (1 << 31) + +#define PB_ERRCS_ES (1 << 1) +#define PB_ISR_PBS_RD_ERR (1 << 8) +#define PCI_IRP_STAT_P_CSR (1 << 23) + +/* * I2C : Register address offset definitions */ -#define I2C_CNTRL1 (0x00000000) -#define I2C_CNTRL2 (0x00000004) -#define I2C_RD_DATA (0x00000008) -#define I2C_TX_DATA (0x0000000c) +#define I2C_CNTRL1 (0x00000000) +#define I2C_CNTRL2 (0x00000004) +#define I2C_RD_DATA (0x00000008) +#define I2C_TX_DATA (0x0000000c) /* * I2C : Register Bit Masks and Reset Values - * definitions for every register + * definitions for every register */ /* I2C_CNTRL1 : Reset Value */ -#define I2C_CNTRL1_RESET_VALUE (0x0000000a) +#define I2C_CNTRL1_RESET_VALUE (0x0000000a) /* I2C_CNTRL1 : Register Bits Masks Definitions */ -#define I2C_CNTRL1_DEVCODE (0x0000000f) -#define I2C_CNTRL1_PAGE (0x00000700) -#define I2C_CNTRL1_BYTADDR (0x00ff0000) -#define I2C_CNTRL1_I2CWRITE (0x01000000) +#define I2C_CNTRL1_DEVCODE (0x0000000f) +#define I2C_CNTRL1_PAGE (0x00000700) +#define I2C_CNTRL1_BYTADDR (0x00ff0000) +#define I2C_CNTRL1_I2CWRITE (0x01000000) /* I2C_CNTRL1 : Read/Write Bit Mask Definition */ -#define I2C_CNTRL1_RWMASK (0x01ff070f) +#define I2C_CNTRL1_RWMASK (0x01ff070f) /* I2C_CNTRL1 : Unused/Reserved bits Definition */ -#define I2C_CNTRL1_RESERVED (0xfe00f8f0) +#define I2C_CNTRL1_RESERVED (0xfe00f8f0) /* I2C_CNTRL2 : Reset Value */ -#define I2C_CNTRL2_RESET_VALUE (0x00000000) +#define I2C_CNTRL2_RESET_VALUE (0x00000000) /* I2C_CNTRL2 : Register Bits Masks Definitions */ -#define I2C_CNTRL2_SIZE (0x00000003) -#define I2C_CNTRL2_LANE (0x0000000c) -#define I2C_CNTRL2_MULTIBYTE (0x00000010) -#define I2C_CNTRL2_START (0x00000100) -#define I2C_CNTRL2_WR_STATUS (0x00010000) -#define I2C_CNTRL2_RD_STATUS (0x00020000) -#define I2C_CNTRL2_I2C_TO_ERR (0x04000000) -#define I2C_CNTRL2_I2C_CFGERR (0x08000000) -#define I2C_CNTRL2_I2C_CMPLT (0x10000000) +#define I2C_CNTRL2_SIZE (0x00000003) +#define I2C_CNTRL2_LANE (0x0000000c) +#define I2C_CNTRL2_MULTIBYTE (0x00000010) +#define I2C_CNTRL2_START (0x00000100) +#define I2C_CNTRL2_WR_STATUS (0x00010000) +#define I2C_CNTRL2_RD_STATUS (0x00020000) +#define I2C_CNTRL2_I2C_TO_ERR (0x04000000) +#define I2C_CNTRL2_I2C_CFGERR (0x08000000) +#define I2C_CNTRL2_I2C_CMPLT (0x10000000) /* I2C_CNTRL2 : Read/Write Bit Mask Definition */ -#define I2C_CNTRL2_RWMASK (0x0000011f) +#define I2C_CNTRL2_RWMASK (0x0000011f) /* I2C_CNTRL2 : Unused/Reserved bits Definition */ -#define I2C_CNTRL2_RESERVED (0xe3fcfee0) +#define I2C_CNTRL2_RESERVED (0xe3fcfee0) /* I2C_RD_DATA : Reset Value */ -#define I2C_RD_DATA_RESET_VALUE (0x00000000) +#define I2C_RD_DATA_RESET_VALUE (0x00000000) /* I2C_RD_DATA : Register Bits Masks Definitions */ -#define I2C_RD_DATA_RBYTE0 (0x000000ff) -#define I2C_RD_DATA_RBYTE1 (0x0000ff00) -#define I2C_RD_DATA_RBYTE2 (0x00ff0000) -#define I2C_RD_DATA_RBYTE3 (0xff000000) +#define I2C_RD_DATA_RBYTE0 (0x000000ff) +#define I2C_RD_DATA_RBYTE1 (0x0000ff00) +#define I2C_RD_DATA_RBYTE2 (0x00ff0000) +#define I2C_RD_DATA_RBYTE3 (0xff000000) /* I2C_RD_DATA : Read/Write Bit Mask Definition */ -#define I2C_RD_DATA_RWMASK (0x00000000) +#define I2C_RD_DATA_RWMASK (0x00000000) /* I2C_RD_DATA : Unused/Reserved bits Definition */ -#define I2C_RD_DATA_RESERVED (0x00000000) +#define I2C_RD_DATA_RESERVED (0x00000000) /* I2C_TX_DATA : Reset Value */ -#define I2C_TX_DATA_RESET_VALUE (0x00000000) +#define I2C_TX_DATA_RESET_VALUE (0x00000000) /* I2C_TX_DATA : Register Bits Masks Definitions */ -#define I2C_TX_DATA_TBYTE0 (0x000000ff) -#define I2C_TX_DATA_TBYTE1 (0x0000ff00) -#define I2C_TX_DATA_TBYTE2 (0x00ff0000) -#define I2C_TX_DATA_TBYTE3 (0xff000000) +#define I2C_TX_DATA_TBYTE0 (0x000000ff) +#define I2C_TX_DATA_TBYTE1 (0x0000ff00) +#define I2C_TX_DATA_TBYTE2 (0x00ff0000) +#define I2C_TX_DATA_TBYTE3 (0xff000000) /* I2C_TX_DATA : Read/Write Bit Mask Definition */ -#define I2C_TX_DATA_RWMASK (0xffffffff) +#define I2C_TX_DATA_RWMASK (0xffffffff) /* I2C_TX_DATA : Unused/Reserved bits Definition */ -#define I2C_TX_DATA_RESERVED (0x00000000) +#define I2C_TX_DATA_RESERVED (0x00000000) -#define TSI108_I2C_OFFSET 0x7000 /* register block offset for general use I2C channel */ -#define TSI108_I2C_SDRAM_OFFSET 0x4400 /* register block offset for SPD I2C channel */ +#define TSI108_I2C_OFFSET 0x7000 /* offset for general use I2C channel */ +#define TSI108_I2C_SDRAM_OFFSET 0x4400 /* offset for SPD I2C channel */ -#define I2C_EEPROM_DEVCODE 0xA /* standard I2C EEPROM device code */ +#define I2C_EEPROM_DEVCODE 0xA /* standard I2C EEPROM device code */ /* I2C status codes */ -#define TSI108_I2C_SUCCESS 0 -#define TSI108_I2C_PARAM_ERR 1 -#define TSI108_I2C_TIMEOUT_ERR 2 -#define TSI108_I2C_IF_BUSY 3 -#define TSI108_I2C_IF_ERROR 4 +#define TSI108_I2C_SUCCESS 0 +#define TSI108_I2C_PARAM_ERR 1 +#define TSI108_I2C_TIMEOUT_ERR 2 +#define TSI108_I2C_IF_BUSY 3 +#define TSI108_I2C_IF_ERROR 4 #endif /* _TSI108_H_ */ -- cgit v1.3.1 From ddd02492f43db5408f5ab9f823b0ba5796e28ef0 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Wed, 6 Dec 2006 11:38:17 +0800 Subject: mpc83xx: Fix the UEC driver bug of QE The patch prevents the GCC tool chain from striping useful code for optimization. It will make UEC ethernet driver workable, Otherwise the UEC will fail in tx when you are using gcc4.x. but the driver can work when using gcc3.4.3. CHANGELOG *Prevent the GCC from striping code for optimization, Otherwise the UEC will tx failed when you are using gcc4.x. Signed-off-by: Dave Liu --- drivers/qe/uec.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index f640c819161..c44a5be9dac 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -1122,7 +1122,7 @@ static int uec_send(struct eth_device* dev, volatile void *buf, int len) uec_private_t *uec; ucc_fast_private_t *uccf; volatile qe_bd_t *bd; - volatile u16 status; + u16 status; int i; int result = 0; @@ -1131,7 +1131,7 @@ static int uec_send(struct eth_device* dev, volatile void *buf, int len) bd = uec->txBd; /* Find an empty TxBD */ - for (i = 0; BD_STATUS(bd) & TxBD_READY; i++) { + for (i = 0; bd->status & TxBD_READY; i++) { if (i > 0x100000) { printf("%s: tx buffer not ready\n", dev->name); return result; @@ -1150,13 +1150,11 @@ static int uec_send(struct eth_device* dev, volatile void *buf, int len) ucc_fast_transmit_on_demand(uccf); /* Wait for buffer to be transmitted */ - status = BD_STATUS(bd); - for (i = 0; status & TxBD_READY; i++) { + for (i = 0; bd->status & TxBD_READY; i++) { if (i > 0x100000) { printf("%s: tx error\n", dev->name); return result; } - status = BD_STATUS(bd); } /* Ok, the buffer be transimitted */ @@ -1171,12 +1169,12 @@ static int uec_recv(struct eth_device* dev) { uec_private_t *uec = dev->priv; volatile qe_bd_t *bd; - volatile u16 status; + u16 status; u16 len; u8 *data; bd = uec->rxBd; - status = BD_STATUS(bd); + status = bd->status; while (!(status & RxBD_EMPTY)) { if (!(status & RxBD_ERROR)) { @@ -1190,7 +1188,7 @@ static int uec_recv(struct eth_device* dev) BD_LENGTH_SET(bd, 0); BD_STATUS_SET(bd, status | RxBD_EMPTY); BD_ADVANCE(bd, status, uec->p_rx_bd_ring); - status = BD_STATUS(bd); + status = bd->status; } uec->rxBd = bd; -- cgit v1.3.1 From 24c3aca3f1358b113d3215adb5433b156e99f72b Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 7 Dec 2006 21:13:15 +0800 Subject: mpc83xx: Add support for the MPC832XEMDS board This patch supports DUART, ETH3/4 and PCI etc. Signed-off-by: Dave Liu --- Makefile | 24 ++ board/mpc832xemds/Makefile | 50 ++++ board/mpc832xemds/config.mk | 28 ++ board/mpc832xemds/mpc832xemds.c | 176 +++++++++++ board/mpc832xemds/pci.c | 313 ++++++++++++++++++++ board/mpc832xemds/u-boot.lds | 123 ++++++++ cpu/mpc83xx/cpu.c | 16 + cpu/mpc83xx/cpu_init.c | 5 + cpu/mpc83xx/speed.c | 39 ++- drivers/qe/qe.h | 2 +- drivers/qe/uec.c | 11 +- include/asm-ppc/e300.h | 5 + include/asm-ppc/immap_83xx.h | 72 ++++- include/asm-ppc/immap_qe.h | 6 + include/configs/MPC832XEMDS.h | 629 ++++++++++++++++++++++++++++++++++++++++ include/mpc83xx.h | 21 +- 16 files changed, 1488 insertions(+), 32 deletions(-) create mode 100644 board/mpc832xemds/Makefile create mode 100644 board/mpc832xemds/config.mk create mode 100644 board/mpc832xemds/mpc832xemds.c create mode 100644 board/mpc832xemds/pci.c create mode 100644 board/mpc832xemds/u-boot.lds create mode 100644 include/configs/MPC832XEMDS.h (limited to 'drivers') diff --git a/Makefile b/Makefile index 358d1817c94..af01a10753c 100644 --- a/Makefile +++ b/Makefile @@ -1648,6 +1648,30 @@ MPC8360EMDS_SLAVE_config: unconfig MPC8349ITX_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc83xx mpc8349itx +MPC832XEMDS_config \ +MPC832XEMDS_HOST_33_config \ +MPC832XEMDS_HOST_66_config \ +MPC832XEMDS_SLAVE_config: unconfig + @echo "" >include/config.h ; \ + if [ "$(findstring _HOST_,$@)" ] ; then \ + echo -n "... PCI HOST " ; \ + echo "#define CONFIG_PCI" >>include/config.h ; \ + fi ; \ + if [ "$(findstring _SLAVE_,$@)" ] ; then \ + echo "...PCI SLAVE 66M" ; \ + echo "#define CONFIG_PCI" >>include/config.h ; \ + echo "#define CONFIG_PCISLAVE" >>include/config.h ; \ + fi ; \ + if [ "$(findstring _33_,$@)" ] ; then \ + echo -n "...33M ..." ; \ + echo "#define PCI_33M" >>include/config.h ; \ + fi ; \ + if [ "$(findstring _66_,$@)" ] ; then \ + echo -n "...66M..." ; \ + echo "#define PCI_66M" >>include/config.h ; \ + fi ; + @$(MKCONFIG) -a MPC832XEMDS ppc mpc83xx mpc832xemds + ######################################################################### ## MPC85xx Systems ######################################################################### diff --git a/board/mpc832xemds/Makefile b/board/mpc832xemds/Makefile new file mode 100644 index 00000000000..5ec7a871d4d --- /dev/null +++ b/board/mpc832xemds/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o pci.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mpc832xemds/config.mk b/board/mpc832xemds/config.mk new file mode 100644 index 00000000000..6c3eca75341 --- /dev/null +++ b/board/mpc832xemds/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# MPC832XEMDS +# + +TEXT_BASE = 0xFE000000 diff --git a/board/mpc832xemds/mpc832xemds.c b/board/mpc832xemds/mpc832xemds.c new file mode 100644 index 00000000000..772da678f00 --- /dev/null +++ b/board/mpc832xemds/mpc832xemds.c @@ -0,0 +1,176 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * + * Dave Liu + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_PCI) +#include +#endif +#if defined(CONFIG_SPD_EEPROM) +#include +#else +#include +#endif +#if defined(CONFIG_OF_FLAT_TREE) +#include +#endif + +const qe_iop_conf_t qe_iop_conf_tab[] = { + /* ETH3 */ + {1, 0, 1, 0, 1}, /* TxD0 */ + {1, 1, 1, 0, 1}, /* TxD1 */ + {1, 2, 1, 0, 1}, /* TxD2 */ + {1, 3, 1, 0, 1}, /* TxD3 */ + {1, 9, 1, 0, 1}, /* TxER */ + {1, 12, 1, 0, 1}, /* TxEN */ + {3, 24, 2, 0, 1}, /* TxCLK->CLK10 */ + + {1, 4, 2, 0, 1}, /* RxD0 */ + {1, 5, 2, 0, 1}, /* RxD1 */ + {1, 6, 2, 0, 1}, /* RxD2 */ + {1, 7, 2, 0, 1}, /* RxD3 */ + {1, 8, 2, 0, 1}, /* RxER */ + {1, 10, 2, 0, 1}, /* RxDV */ + {0, 13, 2, 0, 1}, /* RxCLK->CLK9 */ + {1, 11, 2, 0, 1}, /* COL */ + {1, 13, 2, 0, 1}, /* CRS */ + + /* ETH4 */ + {1, 18, 1, 0, 1}, /* TxD0 */ + {1, 19, 1, 0, 1}, /* TxD1 */ + {1, 20, 1, 0, 1}, /* TxD2 */ + {1, 21, 1, 0, 1}, /* TxD3 */ + {1, 27, 1, 0, 1}, /* TxER */ + {1, 30, 1, 0, 1}, /* TxEN */ + {3, 6, 2, 0, 1}, /* TxCLK->CLK8 */ + + {1, 22, 2, 0, 1}, /* RxD0 */ + {1, 23, 2, 0, 1}, /* RxD1 */ + {1, 24, 2, 0, 1}, /* RxD2 */ + {1, 25, 2, 0, 1}, /* RxD3 */ + {1, 26, 1, 0, 1}, /* RxER */ + {1, 28, 2, 0, 1}, /* Rx_DV */ + {3, 31, 2, 0, 1}, /* RxCLK->CLK7 */ + {1, 29, 2, 0, 1}, /* COL */ + {1, 31, 2, 0, 1}, /* CRS */ + + {3, 4, 3, 0, 2}, /* MDIO */ + {3, 5, 1, 0, 2}, /* MDC */ + + {0, 0, 0, 0, QE_IOP_TAB_END}, /* END of table */ +}; + +int board_early_init_f(void) +{ + volatile u8 *bcsr = (volatile u8 *)CFG_BCSR; + + /* Enable flash write */ + bcsr[9] &= ~0x08; + + return 0; +} + +int fixed_sdram(void); + +long int initdram(int board_type) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) + return -1; + + /* DDR SDRAM - Main SODIMM */ + im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR; + + msize = fixed_sdram(); + + puts("\n DDR RAM: "); + + /* return total bus SDRAM size(bytes) -- DDR */ + return (msize * 1024 * 1024); +} + +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + ************************************************************************/ +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = 0; + u32 ddr_size; + u32 ddr_size_log2; + + msize = CFG_DDR_SIZE; + for (ddr_size = msize << 20, ddr_size_log2 = 0; + (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) { + if (ddr_size & 1) { + return -1; + } + } + im->sysconf.ddrlaw[0].ar = + LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE); +#if (CFG_DDR_SIZE != 128) +#warning Currenly any ddr size other than 128 is not supported +#endif + im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL; + im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG; + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE2; + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + __asm__ __volatile__ ("sync"); + udelay(200); + + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + __asm__ __volatile__ ("sync"); + return msize; +} + +int checkboard(void) +{ + puts("Board: Freescale MPC832XEMDS\n"); + return 0; +} + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void +ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif diff --git a/board/mpc832xemds/pci.c b/board/mpc832xemds/pci.c new file mode 100644 index 00000000000..09f3ac347c0 --- /dev/null +++ b/board/mpc832xemds/pci.c @@ -0,0 +1,313 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +/* + * PCI Configuration space access support for MPC83xx PCI Bridge + */ +#include +#include +#include +#include +#include + +#include + +DECLARE_GLOBAL_DATA_PTR; + +#if defined(CONFIG_PCI) +#define PCI_FUNCTION_CONFIG 0x44 +#define PCI_FUNCTION_CFG_LOCK 0x20 + +/* + * Initialize PCI Devices, report devices found + */ +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc83xxemds_config_table[] = { + { + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + pci_cfgfunc_config_device, + {PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMON_MEMORY | PCI_COMMAND_MASTER} + }, + {} +} +#endif +static struct pci_controller hose[] = { + { +#ifndef CONFIG_PCI_PNP + config_table:pci_mpc83xxemds_config_table, +#endif + }, +}; + +/********************************************************************** + * pci_init_board() + *********************************************************************/ +void pci_init_board(void) +#ifdef CONFIG_PCISLAVE +{ + u16 reg16; + volatile immap_t *immr; + volatile law83xx_t *pci_law; + volatile pot83xx_t *pci_pot; + volatile pcictrl83xx_t *pci_ctrl; + volatile pciconf83xx_t *pci_conf; + + immr = (immap_t *) CFG_IMMR; + pci_law = immr->sysconf.pcilaw; + pci_pot = immr->ios.pot; + pci_ctrl = immr->pci_ctrl; + pci_conf = immr->pci_conf; + /* + * Configure PCI Inbound Translation Windows + */ + pci_ctrl[0].pitar0 = 0x0; + pci_ctrl[0].pibar0 = 0x0; + pci_ctrl[0].piwar0 = PIWAR_EN | PIWAR_RTT_SNOOP | + PIWAR_WTT_SNOOP | PIWAR_IWS_4K; + + pci_ctrl[0].pitar1 = 0x0; + pci_ctrl[0].pibar1 = 0x0; + pci_ctrl[0].piebar1 = 0x0; + pci_ctrl[0].piwar1 &= ~PIWAR_EN; + + pci_ctrl[0].pitar2 = 0x0; + pci_ctrl[0].pibar2 = 0x0; + pci_ctrl[0].piebar2 = 0x0; + pci_ctrl[0].piwar2 &= ~PIWAR_EN; + + hose[0].first_busno = 0; + hose[0].last_busno = 0xff; + pci_setup_indirect(&hose[0], + (CFG_IMMR + 0x8300), (CFG_IMMR + 0x8304)); + reg16 = 0xff; + + pci_hose_read_config_word(&hose[0], PCI_BDF(0, 0, 0), + PCI_COMMAND, ®16); + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MEMORY; + pci_hose_write_config_word(&hose[0], PCI_BDF(0, 0, 0), + PCI_COMMAND, reg16); + + /* + * Clear non-reserved bits in status register. + */ + pci_hose_write_config_word(&hose[0], PCI_BDF(0, 0, 0), + PCI_STATUS, 0xffff); + pci_hose_write_config_byte(&hose[0], PCI_BDF(0, 0, 0), + PCI_LATENCY_TIMER, 0x80); + + /* + * Unlock configuration lock in PCI function configuration register. + */ + pci_hose_read_config_word(&hose[0], PCI_BDF(0, 0, 0), + PCI_FUNCTION_CONFIG, ®16); + reg16 &= ~(PCI_FUNCTION_CFG_LOCK); + pci_hose_write_config_word(&hose[0], PCI_BDF(0, 0, 0), + PCI_FUNCTION_CONFIG, reg16); + + printf("Enabled PCI 32bit Agent Mode\n"); +} +#else +{ + volatile immap_t *immr; + volatile clk83xx_t *clk; + volatile law83xx_t *pci_law; + volatile pot83xx_t *pci_pot; + volatile pcictrl83xx_t *pci_ctrl; + volatile pciconf83xx_t *pci_conf; + + u8 val8, orig_i2c_bus; + u16 reg16; + u32 val32; + u32 dev; + + immr = (immap_t *) CFG_IMMR; + clk = (clk83xx_t *) & immr->clk; + pci_law = immr->sysconf.pcilaw; + pci_pot = immr->ios.pot; + pci_ctrl = immr->pci_ctrl; + pci_conf = immr->pci_conf; + /* + * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode + */ + val32 = clk->occr; + udelay(2000); +#if defined(PCI_66M) + clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2; + printf("PCI clock is 66MHz\n"); +#elif defined(PCI_33M) + clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 | + OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR; + printf("PCI clock is 33MHz\n"); +#else + clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2; + printf("PCI clock is 66MHz\n"); +#endif + udelay(2000); + + /* + * Configure PCI Local Access Windows + */ + pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_512M; + + pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_1M; + + /* + * Configure PCI Outbound Translation Windows + */ + + /* PCI mem space - prefetch */ + pci_pot[0].potar = (CFG_PCI_MEM_BASE >> 12) & POTAR_TA_MASK; + pci_pot[0].pobar = (CFG_PCI_MEM_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[0].pocmr = + POCMR_EN | POCMR_SE | (POCMR_CM_256M & POCMR_CM_MASK); + + /* PCI mmio - non-prefetch mem space */ + pci_pot[1].potar = (CFG_PCI_MMIO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[1].pobar = (CFG_PCI_MMIO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[1].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK); + + /* PCI IO space */ + pci_pot[2].potar = (CFG_PCI_IO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[2].pobar = (CFG_PCI_IO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[2].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK); + + /* + * Configure PCI Inbound Translation Windows + */ + pci_ctrl[0].pitar1 = (CFG_PCI_SLV_MEM_LOCAL >> 12) & PITAR_TA_MASK; + pci_ctrl[0].pibar1 = (CFG_PCI_SLV_MEM_BUS >> 12) & PIBAR_MASK; + pci_ctrl[0].piebar1 = 0x0; + pci_ctrl[0].piwar1 = + PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | + PIWAR_IWS_2G; + + /* + * Assign PIB PMC slot to desired PCI bus + */ + + /* Switch temporarily to I2C bus #2 */ + orig_i2c_bus = i2c_get_bus_num(); + i2c_set_bus_num(1); + + val8 = 0; + i2c_write(0x23, 0x6, 1, &val8, 1); + i2c_write(0x23, 0x7, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x23, 0x2, 1, &val8, 1); + i2c_write(0x23, 0x3, 1, &val8, 1); + + val8 = 0; + i2c_write(0x26, 0x6, 1, &val8, 1); + val8 = 0x34; + i2c_write(0x26, 0x7, 1, &val8, 1); + + val8 = 0xf9; /* PMC2, PMC3 slot to PCI bus */ + i2c_write(0x26, 0x2, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x26, 0x3, 1, &val8, 1); + + val8 = 0; + i2c_write(0x27, 0x6, 1, &val8, 1); + i2c_write(0x27, 0x7, 1, &val8, 1); + val8 = 0xff; + i2c_write(0x27, 0x2, 1, &val8, 1); + val8 = 0xef; + i2c_write(0x27, 0x3, 1, &val8, 1); + asm("eieio"); + + /* Reset to original I2C bus */ + i2c_set_bus_num(orig_i2c_bus); + + /* + * Release PCI RST Output signal + */ + udelay(2000); + pci_ctrl[0].gcr = 1; + udelay(2000); + + hose[0].first_busno = 0; + hose[0].last_busno = 0xff; + + /* PCI memory prefetch space */ + pci_set_region(hose[0].regions + 0, + CFG_PCI_MEM_BASE, + CFG_PCI_MEM_PHYS, + CFG_PCI_MEM_SIZE, PCI_REGION_MEM | PCI_REGION_PREFETCH); + + /* PCI memory space */ + pci_set_region(hose[0].regions + 1, + CFG_PCI_MMIO_BASE, + CFG_PCI_MMIO_PHYS, CFG_PCI_MMIO_SIZE, PCI_REGION_MEM); + + /* PCI IO space */ + pci_set_region(hose[0].regions + 2, + CFG_PCI_IO_BASE, + CFG_PCI_IO_PHYS, CFG_PCI_IO_SIZE, PCI_REGION_IO); + + /* System memory space */ + pci_set_region(hose[0].regions + 3, + CFG_PCI_SLV_MEM_LOCAL, + CFG_PCI_SLV_MEM_BUS, + CFG_PCI_SLV_MEM_SIZE, + PCI_REGION_MEM | PCI_REGION_MEMORY); + + hose[0].region_count = 4; + + pci_setup_indirect(&hose[0], + (CFG_IMMR + 0x8300), (CFG_IMMR + 0x8304)); + + pci_register_hose(hose); + + /* + * Write command register + */ + reg16 = 0xff; + dev = PCI_BDF(0, 0, 0); + pci_hose_read_config_word(&hose[0], dev, PCI_COMMAND, ®16); + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; + pci_hose_write_config_word(&hose[0], dev, PCI_COMMAND, reg16); + + /* + * Clear non-reserved bits in status register. + */ + pci_hose_write_config_word(&hose[0], dev, PCI_STATUS, 0xffff); + pci_hose_write_config_byte(&hose[0], dev, PCI_LATENCY_TIMER, 0x80); + pci_hose_write_config_byte(&hose[0], dev, PCI_CACHE_LINE_SIZE, 0x08); + + printf("PCI 32bit bus on PMC2 & PMC3\n"); + + /* + * Hose scan. + */ + hose->last_busno = pci_hose_scan(hose); +} +#endif /* CONFIG_PCISLAVE */ + +#ifdef CONFIG_OF_FLAT_TREE +void +ft_pci_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + + p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8500/bus-range", &len); + if (p != NULL) { + p[0] = hose[0].first_busno; + p[1] = hose[0].last_busno; + } +} +#endif /* CONFIG_OF_FLAT_TREE */ +#endif /* CONFIG_PCI */ diff --git a/board/mpc832xemds/u-boot.lds b/board/mpc832xemds/u-boot.lds new file mode 100644 index 00000000000..937c87a27cd --- /dev/null +++ b/board/mpc832xemds/u-boot.lds @@ -0,0 +1,123 @@ +/* + * (C) Copyright 2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc83xx/start.o (.text) + *(.text) + *(.fixup) + *(.got1) + . = ALIGN(16); + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} +ENTRY(_start) diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index 1b5107881ed..bc61219337e 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -92,6 +92,22 @@ int checkcpu(void) case SPR_8360_REV12: puts("MPC8360, "); break; + case SPR_8323E_REV10: + case SPR_8323E_REV11: + puts("MPC8323E, "); + break; + case SPR_8323_REV10: + case SPR_8323_REV11: + puts("MPC8323, "); + break; + case SPR_8321E_REV10: + case SPR_8321E_REV11: + puts("MPC8321E, "); + break; + case SPR_8321_REV10: + case SPR_8321_REV11: + puts("MPC8321, "); + break; default: puts("Rev: Unknown\n"); return -1; /* Not sure what this is */ diff --git a/cpu/mpc83xx/cpu_init.c b/cpu/mpc83xx/cpu_init.c index 7574fabf864..eb256e598d3 100644 --- a/cpu/mpc83xx/cpu_init.c +++ b/cpu/mpc83xx/cpu_init.c @@ -119,6 +119,11 @@ void cpu_init_f (volatile immap_t * im) #ifdef CFG_SICRL im->sysconf.sicrl = CFG_SICRL; #endif + /* DDR control driver register */ +#ifdef CFG_DDRCDR + im->sysconf.ddrcdr = CFG_DDRCDR; +#endif + #ifdef CONFIG_QE /* Config QE ioports */ config_qe_ioports(); diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c index 40ba6b04a3b..9fd1bf1bae8 100644 --- a/cpu/mpc83xx/speed.c +++ b/cpu/mpc83xx/speed.c @@ -107,15 +107,19 @@ int get_clocks(void) #endif u32 core_clk; u32 i2c1_clk; +#if !defined(CONFIG_MPC832X) u32 i2c2_clk; +#endif u32 enc_clk; u32 lbiu_clk; u32 lclk_clk; u32 ddr_clk; -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) + u32 ddr_sec_clk; +#endif +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) u32 qepmf; u32 qepdf; - u32 ddr_sec_clk; u32 qe_clk; u32 brg_clk; #endif @@ -227,10 +231,12 @@ int get_clocks(void) return -9; } #endif -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) i2c1_clk = csb_clk; #endif +#if !defined(CONFIG_MPC832X) i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ +#endif switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { case 0: @@ -249,12 +255,9 @@ int get_clocks(void) /* unkown SCCR_ENCCM value */ return -6; } -#if defined(CONFIG_MPC8349) || defined(CONFIG_MPC8360) + lbiu_clk = csb_clk * (1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); -#else -#error Unknown MPC83xx chip -#endif lcrr = (im->lbus.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT; switch (lcrr) { case 2: @@ -266,16 +269,13 @@ int get_clocks(void) /* unknown lcrr */ return -10; } -#if defined(CONFIG_MPC8349) || defined(CONFIG_MPC8360) + ddr_clk = csb_clk * (1 + ((im->reset.rcwl & HRCWL_DDRCM) >> HRCWL_DDRCM_SHIFT)); corepll = (im->reset.rcwl & HRCWL_COREPLL) >> HRCWL_COREPLL_SHIFT; -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) ddr_sec_clk = csb_clk * (1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); -#endif -#else -#error Unknown MPC83xx chip #endif corecnf_tab_index = ((corepll & 0x1F) << 2) | ((corepll & 0x60) >> 5); @@ -306,7 +306,7 @@ int get_clocks(void) return -12; } -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) qepmf = (im->reset.rcwl & HRCWL_CEPMF) >> HRCWL_CEPMF_SHIFT; qepdf = (im->reset.rcwl & HRCWL_CEPDF) >> HRCWL_CEPDF_SHIFT; qe_clk = (pci_sync_in * qepmf) / (1 + qepdf); @@ -322,13 +322,17 @@ int get_clocks(void) #endif gd->core_clk = core_clk; gd->i2c1_clk = i2c1_clk; +#if !defined(CONFIG_MPC832X) gd->i2c2_clk = i2c2_clk; +#endif gd->enc_clk = enc_clk; gd->lbiu_clk = lbiu_clk; gd->lclk_clk = lclk_clk; gd->ddr_clk = ddr_clk; -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) gd->ddr_sec_clk = ddr_sec_clk; +#endif +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) gd->qe_clk = qe_clk; gd->brg_clk = brg_clk; #endif @@ -352,18 +356,21 @@ int print_clock_conf(void) printf("Clock configuration:\n"); printf(" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000); printf(" Core: %4d MHz\n", gd->core_clk / 1000000); -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) printf(" QE: %4d MHz\n", gd->qe_clk / 1000000); + printf(" BRG: %4d MHz\n", gd->brg_clk / 1000000); #endif printf(" Local Bus Controller:%4d MHz\n", gd->lbiu_clk / 1000000); printf(" Local Bus: %4d MHz\n", gd->lclk_clk / 1000000); printf(" DDR: %4d MHz\n", gd->ddr_clk / 1000000); -#if defined (CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) printf(" DDR Secondary: %4d MHz\n", gd->ddr_sec_clk / 1000000); #endif printf(" SEC: %4d MHz\n", gd->enc_clk / 1000000); printf(" I2C1: %4d MHz\n", gd->i2c1_clk / 1000000); +#if !defined(CONFIG_MPC832X) printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000); +#endif #if defined(CONFIG_MPC8349) printf(" TSEC1: %4d MHz\n", gd->tsec1_clk / 1000000); printf(" TSEC2: %4d MHz\n", gd->tsec2_clk / 1000000); diff --git a/drivers/qe/qe.h b/drivers/qe/qe.h index f7f8ed0a724..0bcd0a9573e 100644 --- a/drivers/qe/qe.h +++ b/drivers/qe/qe.h @@ -30,7 +30,7 @@ #define UCC_MAX_NUM 8 #define QE_DATAONLY_BASE (uint)(128) -#define QE_DATAONLY_SIZE ((uint)(0xc000) - QE_DATAONLY_BASE) +#define QE_DATAONLY_SIZE (QE_MURAM_SIZE - QE_DATAONLY_BASE) /* QE threads SNUM */ diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index c44a5be9dac..aea455b8dc0 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -432,7 +432,12 @@ static int init_phy(struct eth_device *dev) } memset(mii_info, 0, sizeof(*mii_info)); - mii_info->speed = SPEED_1000; + if (uec->uec_info->uf_info.eth_type == GIGA_ETH) { + mii_info->speed = SPEED_1000; + } else { + mii_info->speed = SPEED_100; + } + mii_info->duplex = DUPLEX_FULL; mii_info->pause = 0; mii_info->link = 1; @@ -508,7 +513,8 @@ static void adjust_link(struct eth_device *dev) } if (mii_info->speed != uec->oldspeed) { - switch (mii_info->speed) { + if (uec->uec_info->uf_info.eth_type == GIGA_ETH) { + switch (mii_info->speed) { case 1000: break; case 100: @@ -531,6 +537,7 @@ static void adjust_link(struct eth_device *dev) printf("%s: Ack,Speed(%d)is illegal\n", dev->name, mii_info->speed); break; + } } printf("%s: Speed %dBT\n", dev->name, mii_info->speed); diff --git a/include/asm-ppc/e300.h b/include/asm-ppc/e300.h index 79dcae416f9..ff9512f203c 100644 --- a/include/asm-ppc/e300.h +++ b/include/asm-ppc/e300.h @@ -15,6 +15,11 @@ #define PVR_8360_REV10 (PVR_83xx | 0x0020) #define PVR_8360_REV11 (PVR_83xx | 0x0020) +#if defined(CONFIG_MPC832X) +#undef PVR_83xx +#define PVR_83xx 0x80840000 +#endif + /* * Hardware Implementation-Dependent Register 0 (HID0) */ diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 67b035c6140..77a079f44e8 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -60,7 +60,10 @@ typedef struct sysconf83xx { u32 spcr; /* System Priority Configuration Register */ u32 sicrl; /* System I/O Configuration Register Low */ u32 sicrh; /* System I/O Configuration Register High */ - u8 res6[0xE4]; + u8 res6[0x0C]; + u32 ddrcdr; /* DDR Control Driver Register */ + u32 ddrdsr; /* DDR Debug Status Register */ + u8 res7[0xD0]; } sysconf83xx_t; /* @@ -274,25 +277,35 @@ typedef struct ddr83xx { ddr_cs_bnds_t csbnds[4];/* Chip Select x Memory Bounds */ u8 res0[0x60]; u32 cs_config[4]; /* Chip Select x Configuration */ - u8 res1[0x78]; + u8 res1[0x70]; + u32 timing_cfg_3; /* SDRAM Timing Configuration 3 */ + u32 timing_cfg_0; /* SDRAM Timing Configuration 0 */ u32 timing_cfg_1; /* SDRAM Timing Configuration 1 */ u32 timing_cfg_2; /* SDRAM Timing Configuration 2 */ u32 sdram_cfg; /* SDRAM Control Configuration */ - u8 res2[4]; + u32 sdram_cfg2; /* SDRAM Control Configuration 2 */ u32 sdram_mode; /* SDRAM Mode Configuration */ - u8 res3[8]; + u32 sdram_mode2; /* SDRAM Mode Configuration 2 */ + u32 sdram_md_cntl; /* SDRAM Mode Control */ u32 sdram_interval; /* SDRAM Interval Configuration */ - u8 res9[8]; - u32 sdram_clk_cntl; - u8 res4[0xCCC]; + u32 ddr_data_init; /* SDRAM Data Initialization */ + u8 res2[4]; + u32 sdram_clk_cntl; /* SDRAM Clock Control */ + u8 res3[0x14]; + u32 ddr_init_addr; /* DDR training initialization address */ + u32 ddr_init_ext_addr; /* DDR training initialization extended address */ + u8 res4[0xAA8]; + u32 ddr_ip_rev1; /* DDR IP block revision 1 */ + u32 ddr_ip_rev2; /* DDR IP block revision 2 */ + u8 res5[0x200]; u32 data_err_inject_hi; /* Memory Data Path Error Injection Mask High */ u32 data_err_inject_lo; /* Memory Data Path Error Injection Mask Low */ u32 ecc_err_inject; /* Memory Data Path Error Injection Mask ECC */ - u8 res5[0x14]; + u8 res6[0x14]; u32 capture_data_hi; /* Memory Data Path Read Capture High */ u32 capture_data_lo; /* Memory Data Path Read Capture Low */ u32 capture_ecc; /* Memory Data Path Read Capture ECC */ - u8 res6[0x14]; + u8 res7[0x14]; u32 err_detect; /* Memory Error Detect */ u32 err_disable; /* Memory Error Disable */ u32 err_int_en; /* Memory Error Interrupt Enable */ @@ -300,9 +313,9 @@ typedef struct ddr83xx { u32 capture_address; /* Memory Error Address Capture */ u32 capture_ext_address;/* Memory Error Extended Address Capture */ u32 err_sbe; /* Memory Single-Bit ECC Error Management */ - u8 res7[0xA4]; + u8 res8[0xA4]; u32 debug_reg; - u8 res8[0xFC]; + u8 res9[0xFC]; } ddr83xx_t; /* @@ -607,6 +620,43 @@ typedef struct immap { u8 res10[0xC0000]; u8 qe[0x100000]; /* QE block */ } immap_t; + +#elif defined(CONFIG_MPC832X) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[2]; /* Global Timers Module */ + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + qepi83xx_t qepi; /* QE Ports Interrupts Registers */ + u8 res0[0x300]; + u8 dll_ddr[0x100]; + u8 dll_lbc[0x100]; + u8 res1[0x200]; + qepio83xx_t qepio; /* QE Parallel I/O ports */ + u8 res2[0x800]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res3[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res4[0x900]; + lbus83xx_t lbus; /* Local Bus Controller Registers */ + u8 res5[0x2000]; + dma83xx_t dma; /* DMA */ + pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */ + u8 res6[128]; + ios83xx_t ios; /* Sequencer (IOS) */ + pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */ + u8 res7[0x27A00]; + security83xx_t security; + u8 res8[0xC0000]; + u8 qe[0x100000]; /* QE block */ +} immap_t; #endif #endif /* __IMMAP_83xx__ */ diff --git a/include/asm-ppc/immap_qe.h b/include/asm-ppc/immap_qe.h index f38503206cc..950b9497f8a 100644 --- a/include/asm-ppc/immap_qe.h +++ b/include/asm-ppc/immap_qe.h @@ -547,4 +547,10 @@ typedef struct qe_immap { extern qe_map_t *qe_immr; +#if defined(CONFIG_MPC8360) +#define QE_MURAM_SIZE 0xc000UL +#elif defined(CONFIG_MPC832X) +#define QE_MURAM_SIZE 0x4000UL +#endif + #endif /* __IMMAP_QE_H__ */ diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h new file mode 100644 index 00000000000..b8bf00f861e --- /dev/null +++ b/include/configs/MPC832XEMDS.h @@ -0,0 +1,629 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ +#define CONFIG_MPC83XX 1 /* MPC83xx family */ +#define CONFIG_MPC832X 1 /* MPC832x CPU specific */ +#define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ + +/* + * System Clock Setup + */ +#ifdef CONFIG_PCISLAVE +#define CONFIG_83XX_PCICLK 66000000 /* in HZ */ +#else +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#endif + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 66000000 +#endif + +/* + * Hardware Reset Configuration Word + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_2X1 |\ + HRCWL_VCO_1X2 |\ + HRCWL_CSB_TO_CLKIN_2X1 |\ + HRCWL_CORE_TO_CSB_2X1 |\ + HRCWL_CE_PLL_VCO_DIV_2 |\ + HRCWL_CE_PLL_DIV_1X1 |\ + HRCWL_CE_TO_PLL_1X3) + +#ifdef CONFIG_PCISLAVE +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_AGENT |\ + HRCWH_PCI1_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_NORMAL) +#else +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_NORMAL) +#endif + +/* + * System IO Config + */ +#define CFG_SICRL 0x00000000 + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ + +#undef CONFIG_SPD_EEPROM +#if defined(CONFIG_SPD_EEPROM) +/* Determine DDR configuration from I2C interface + */ +#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ +#else +/* Manually set up DDR parameters + */ +#define CFG_DDR_SIZE 128 /* MB */ +#define CFG_DDR_CS0_CONFIG 0x80840102 +#define CFG_DDR_TIMING_0 0x00220802 +#define CFG_DDR_TIMING_1 0x3935d322 +#define CFG_DDR_TIMING_2 0x0f9048ca +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_CLK_CNTL 0x02000000 +#define CFG_DDR_MODE 0x44400232 +#define CFG_DDR_MODE2 0x8000c000 +#define CFG_DDR_INTERVAL 0x03200064 +#define CFG_DDR_CS0_BNDS 0x00000007 +#define CFG_DDR_SDRAM_CFG 0x43080000 +#define CFG_DDR_SDRAM_CFG2 0x00401000 +#endif + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00000000 /* memtest region */ +#define CFG_MEMTEST_END 0x00100000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) +#define CFG_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM + +/* + * BCSR on the Local Bus + */ +#define CFG_BCSR 0xF8000000 +#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ +#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ + +#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ +#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ + +/* + * SDRAM on the Local Bus + */ +#undef CFG_LB_SDRAM /* The board has not SRDAM on local bus */ + +#ifdef CFG_LB_SDRAM +#define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +#define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE +#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ + +/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 + * + * CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * the top 17 bits of BR2. + */ + +#define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 + */ + +#define CFG_OR2_PRELIM 0xfc006901 + +#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +#define CFG_LBC_LSDMR_COMMON 0x0063b723 + +/* + * SDRAM Controller configuration sequence. + */ +#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_PCHALL) +#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_MRW) +#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_NORMAL) + +#endif + +/* + * Windows to access PIB via local bus + */ +#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ +#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ + +/* + * CS2 on Local Bus, to PIB + */ +#define CFG_BR2_PRELIM 0xf8008801 /* CS2 base address at 0xf8008000 */ +#define CFG_OR2_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ + +/* + * CS3 on Local Bus, to PIB + */ +#define CFG_BR3_PRELIM 0xf8010801 /* CS3 base address at 0xf8010000 */ +#define CFG_OR3_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,8323@0" +#define OF_SOC "soc8323@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc8323@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI_MEM_BASE 0x80000000 +#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_MMIO_BASE 0x90000000 +#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE +#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_IO_BASE 0xE0300000 +#define CFG_PCI_IO_PHYS 0xE0300000 +#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE +#define CFG_PCI_SLV_MEM_BUS 0x00000000 +#define CFG_PCI_SLV_MEM_SIZE 0x80000000 + + +#ifdef CONFIG_PCI + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "Freescale GETH" + +#define CONFIG_UEC_ETH1 /* ETH3 */ + +#ifdef CONFIG_UEC_ETH1 +#define CFG_UEC1_UCC_NUM 2 /* UCC3 */ +#define CFG_UEC1_RX_CLK QE_CLK9 +#define CFG_UEC1_TX_CLK QE_CLK10 +#define CFG_UEC1_ETH_TYPE FAST_ETH +#define CFG_UEC1_PHY_ADDR 3 +#define CFG_UEC1_INTERFACE_MODE ENET_100_MII +#endif + +#define CONFIG_UEC_ETH2 /* ETH4 */ + +#ifdef CONFIG_UEC_ETH2 +#define CFG_UEC2_UCC_NUM 3 /* UCC4 */ +#define CFG_UEC2_RX_CLK QE_CLK7 +#define CFG_UEC2_TX_CLK QE_CLK8 +#define CFG_UEC2_ETH_TYPE FAST_ETH +#define CFG_UEC2_PHY_ADDR 4 +#define CFG_UEC2_INTERFACE_MODE ENET_100_MII +#endif + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CFG_RAMBOOT) +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_ASKENV \ + | CFG_CMD_PCI \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) +#else +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_ASKENV \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) +#endif +#else +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_ASKENV \ + | CFG_CMD_I2C) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_ASKENV \ + | CFG_CMD_I2C ) +#endif +#endif + +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Cache Config + */ +#define CFG_DCACHE_SIZE 16384 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +/* IMMRBAR & PCI IO: cache-inhibit and guarded */ +#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* BCSR: cache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_BCSR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT3U CFG_IBAT3U + +#define CFG_IBAT4L (0) +#define CFG_IBAT4U (0) +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#else +#define CFG_IBAT6L (0) +#define CFG_IBAT6U (0) +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_UEC_ETH) +#define CONFIG_ETHADDR 00:04:9f:ef:03:01 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:04:9f:ef:03:02 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=ramfs.83xx\0" \ + "fdtaddr=400000\0" \ + "fdtfile=mpc832xemds.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 504b6a97bc7..52e43691513 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -75,6 +75,15 @@ #define SPR_8360E_REV12 0x80480012 #define SPR_8360_REV12 0x80490012 +#define SPR_8323E_REV10 0x80620010 +#define SPR_8323_REV10 0x80630010 +#define SPR_8321E_REV10 0x80660010 +#define SPR_8321_REV10 0x80670010 +#define SPR_8323E_REV11 0x80620011 +#define SPR_8323_REV11 0x80630011 +#define SPR_8321E_REV11 0x80660011 +#define SPR_8321_REV11 0x80670011 + /* SPCR - System Priority Configuration Register */ #define SPCR_PCIHPE 0x10000000 /* PCI Highest Priority Enable */ @@ -167,6 +176,14 @@ #define SICRH_UC1EOBI 0x00000004 #define SICRH_UC2E1OBI 0x00000002 #define SICRH_UC2E2OBI 0x00000001 + +#elif defined(CONFIG_MPC832X) +/* SICRL bits - MPC832X specific */ +#define SICRL_LDP_LCS_A 0x80000000 +#define SICRL_IRQ_CKS 0x20000000 +#define SICRL_PCI_MSRC 0x10000000 +#define SICRL_URT_CTPR 0x06000000 +#define SICRL_IRQ_CTPR 0x00C00000 #endif /* SWCRR - System Watchdog Control Register @@ -270,7 +287,7 @@ #define HRCWL_CORE_TO_CSB_2_5X1 0x00050000 #define HRCWL_CORE_TO_CSB_3X1 0x00060000 -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) #define HRCWL_CEVCOD 0x000000C0 #define HRCWL_CEVCOD_SHIFT 6 #define HRCWL_CE_PLL_VCO_DIV_4 0x00000000 @@ -718,7 +735,7 @@ #define BR_MS_UPMA 0x00000080 /* UPMA */ #define BR_MS_UPMB 0x000000A0 /* UPMB */ #define BR_MS_UPMC 0x000000C0 /* UPMC */ -#if defined(CONFIG_MPC8360) +#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) #define BR_ATOM 0x0000000C #define BR_ATOM_SHIFT 2 #endif -- cgit v1.3.1 From 91e25769771c1164ed63ffca0add49f934ae3343 Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Tue, 16 Jan 2007 11:38:14 -0500 Subject: mpc83xx: U-Boot support for Wind River SBC8349 I've redone the SBC8349 support to match git-current, which incorporates all the MPC834x updates from Freescale since the 1.1.6 release, including the DDR changes. I've kept all the SBC8349 files as parallel as possible to the MPC8349EMDS ones for ease of maintenance and to allow for easy inspection of what was changed to support this board. Hence the SBC8349 U-Boot has FDT support and everything else that the MPC8349EMDS has. Fortunately the Freescale updates added support for boards using CS0, but I had to change spd_sdram.c to allow for board specific settings for the sdram_clk_cntl (it is/was hard coded to zero, and that remains the default if the board doesn't specify a value.) Hopefully this should be mergeable as-is and require no whitespace cleanups or similar, but if something doesn't measure up then let me know and I'll fix it. Thanks, Paul. --- CREDITS | 4 + Makefile | 3 + board/sbc8349/Makefile | 49 +++ board/sbc8349/config.mk | 27 ++ board/sbc8349/pci.c | 348 ++++++++++++++++++++++ board/sbc8349/sbc8349.c | 585 ++++++++++++++++++++++++++++++++++++ board/sbc8349/u-boot.lds | 125 ++++++++ cpu/mpc83xx/spd_sdram.c | 4 + doc/README.sbc8349 | 99 ++++++ drivers/tsec.c | 84 ++++++ drivers/tsec.h | 5 + include/configs/sbc8349.h | 744 ++++++++++++++++++++++++++++++++++++++++++++++ 12 files changed, 2077 insertions(+) create mode 100644 board/sbc8349/Makefile create mode 100644 board/sbc8349/config.mk create mode 100644 board/sbc8349/pci.c create mode 100644 board/sbc8349/sbc8349.c create mode 100644 board/sbc8349/u-boot.lds create mode 100644 doc/README.sbc8349 create mode 100644 include/configs/sbc8349.h (limited to 'drivers') diff --git a/CREDITS b/CREDITS index 802158879f2..0099bd46c26 100644 --- a/CREDITS +++ b/CREDITS @@ -160,6 +160,10 @@ N: Thomas Frieden E: ThomasF@hyperion-entertainment.com D: Support for AmigaOne +N: Paul Gortmaker +E: paul.gortmaker@windriver.com +D: Support for WRS SBC8347/8349 boards + N: Frank Gottschling E: fgottschling@eltec.de D: Support for ELTEC MHPC/BAB7xx/ELPPC boards, cfb-console, i8042, SMI LynxEM diff --git a/Makefile b/Makefile index af01a10753c..0d11f82ec40 100644 --- a/Makefile +++ b/Makefile @@ -1648,6 +1648,9 @@ MPC8360EMDS_SLAVE_config: unconfig MPC8349ITX_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc83xx mpc8349itx +sbc8349_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349 + MPC832XEMDS_config \ MPC832XEMDS_HOST_33_config \ MPC832XEMDS_HOST_66_config \ diff --git a/board/sbc8349/Makefile b/board/sbc8349/Makefile new file mode 100644 index 00000000000..02cf569b5b8 --- /dev/null +++ b/board/sbc8349/Makefile @@ -0,0 +1,49 @@ +# +# Copyright (c) 2006 Wind River Systems, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o pci.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/sbc8349/config.mk b/board/sbc8349/config.mk new file mode 100644 index 00000000000..05fa5a07d57 --- /dev/null +++ b/board/sbc8349/config.mk @@ -0,0 +1,27 @@ +# +# Copyright (c) 2006 Wind River Systems, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# SBC8349E +# + +TEXT_BASE = 0xFFF00000 diff --git a/board/sbc8349/pci.c b/board/sbc8349/pci.c new file mode 100644 index 00000000000..eadf230983d --- /dev/null +++ b/board/sbc8349/pci.c @@ -0,0 +1,348 @@ +/* + * pci.c -- WindRiver SBC8349 PCI board support. + * Copyright (c) 2006 Wind River Systems, Inc. + * + * Based on MPC8349 PCI support but w/o PIB related code. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#ifdef CONFIG_PCI + +/* System RAM mapped to PCI space */ +#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE + +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc8349emds_config_table[] = { + {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + PCI_IDSEL_NUMBER, PCI_ANY_ID, + pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER + } + }, + {} +}; +#endif + +static struct pci_controller pci_hose[] = { + { +#ifndef CONFIG_PCI_PNP + config_table:pci_mpc8349emds_config_table, +#endif + }, + { +#ifndef CONFIG_PCI_PNP + config_table:pci_mpc8349emds_config_table, +#endif + } +}; + +/************************************************************************** + * pci_init_board() + * + * NOTICE: PCI2 is not supported. There is only one + * physical PCI slot on the board. + * + */ +void +pci_init_board(void) +{ + volatile immap_t * immr; + volatile clk83xx_t * clk; + volatile law83xx_t * pci_law; + volatile pot83xx_t * pci_pot; + volatile pcictrl83xx_t * pci_ctrl; + volatile pciconf83xx_t * pci_conf; + u16 reg16; + u32 reg32; + u32 dev; + struct pci_controller * hose; + + immr = (immap_t *)CFG_IMMR; + clk = (clk83xx_t *)&immr->clk; + pci_law = immr->sysconf.pcilaw; + pci_pot = immr->ios.pot; + pci_ctrl = immr->pci_ctrl; + pci_conf = immr->pci_conf; + + hose = &pci_hose[0]; + + /* + * Configure PCI controller and PCI_CLK_OUTPUT both in 66M mode + */ + + reg32 = clk->occr; + udelay(2000); + clk->occr = 0xff000000; + udelay(2000); + + /* + * Release PCI RST Output signal + */ + pci_ctrl[0].gcr = 0; + udelay(2000); + pci_ctrl[0].gcr = 1; + +#ifdef CONFIG_MPC83XX_PCI2 + pci_ctrl[1].gcr = 0; + udelay(2000); + pci_ctrl[1].gcr = 1; +#endif + + /* We need to wait at least a 1sec based on PCI specs */ + { + int i; + + for (i = 0; i < 1000; ++i) + udelay (1000); + } + + /* + * Configure PCI Local Access Windows + */ + pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LAWAR_EN | LAWAR_SIZE_1G; + + pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LAWAR_EN | LAWAR_SIZE_4M; + + /* + * Configure PCI Outbound Translation Windows + */ + + /* PCI1 mem space - prefetch */ + pci_pot[0].potar = (CFG_PCI1_MEM_BASE >> 12) & POTAR_TA_MASK; + pci_pot[0].pobar = (CFG_PCI1_MEM_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[0].pocmr = POCMR_EN | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK); + + /* PCI1 IO space */ + pci_pot[1].potar = (CFG_PCI1_IO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[1].pobar = (CFG_PCI1_IO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[1].pocmr = POCMR_EN | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK); + + /* PCI1 mmio - non-prefetch mem space */ + pci_pot[2].potar = (CFG_PCI1_MMIO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[2].pobar = (CFG_PCI1_MMIO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[2].pocmr = POCMR_EN | (POCMR_CM_256M & POCMR_CM_MASK); + + /* + * Configure PCI Inbound Translation Windows + */ + + /* we need RAM mapped to PCI space for the devices to + * access main memory */ + pci_ctrl[0].pitar1 = 0x0; + pci_ctrl[0].pibar1 = 0x0; + pci_ctrl[0].piebar1 = 0x0; + pci_ctrl[0].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1); + + hose->first_busno = 0; + hose->last_busno = 0xff; + + /* PCI memory prefetch space */ + pci_set_region(hose->regions + 0, + CFG_PCI1_MEM_BASE, + CFG_PCI1_MEM_PHYS, + CFG_PCI1_MEM_SIZE, + PCI_REGION_MEM|PCI_REGION_PREFETCH); + + /* PCI memory space */ + pci_set_region(hose->regions + 1, + CFG_PCI1_MMIO_BASE, + CFG_PCI1_MMIO_PHYS, + CFG_PCI1_MMIO_SIZE, + PCI_REGION_MEM); + + /* PCI IO space */ + pci_set_region(hose->regions + 2, + CFG_PCI1_IO_BASE, + CFG_PCI1_IO_PHYS, + CFG_PCI1_IO_SIZE, + PCI_REGION_IO); + + /* System memory space */ + pci_set_region(hose->regions + 3, + CONFIG_PCI_SYS_MEM_BUS, + CONFIG_PCI_SYS_MEM_PHYS, + gd->ram_size, + PCI_REGION_MEM | PCI_REGION_MEMORY); + + hose->region_count = 4; + + pci_setup_indirect(hose, + (CFG_IMMR+0x8300), + (CFG_IMMR+0x8304)); + + pci_register_hose(hose); + + /* + * Write to Command register + */ + reg16 = 0xff; + dev = PCI_BDF(hose->first_busno, 0, 0); + pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16); + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; + pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16); + + /* + * Clear non-reserved bits in status register. + */ + pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff); + pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80); + pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08); + +#ifdef CONFIG_PCI_SCAN_SHOW + printf("PCI: Bus Dev VenId DevId Class Int\n"); +#endif + /* + * Hose scan. + */ + hose->last_busno = pci_hose_scan(hose); + +#ifdef CONFIG_MPC83XX_PCI2 + hose = &pci_hose[1]; + + /* + * Configure PCI Outbound Translation Windows + */ + + /* PCI2 mem space - prefetch */ + pci_pot[3].potar = (CFG_PCI2_MEM_BASE >> 12) & POTAR_TA_MASK; + pci_pot[3].pobar = (CFG_PCI2_MEM_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[3].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_PREFETCH_EN | (POCMR_CM_256M & POCMR_CM_MASK); + + /* PCI2 IO space */ + pci_pot[4].potar = (CFG_PCI2_IO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[4].pobar = (CFG_PCI2_IO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[4].pocmr = POCMR_EN | POCMR_PCI2 | POCMR_IO | (POCMR_CM_1M & POCMR_CM_MASK); + + /* PCI2 mmio - non-prefetch mem space */ + pci_pot[5].potar = (CFG_PCI2_MMIO_BASE >> 12) & POTAR_TA_MASK; + pci_pot[5].pobar = (CFG_PCI2_MMIO_PHYS >> 12) & POBAR_BA_MASK; + pci_pot[5].pocmr = POCMR_EN | POCMR_PCI2 | (POCMR_CM_256M & POCMR_CM_MASK); + + /* + * Configure PCI Inbound Translation Windows + */ + + /* we need RAM mapped to PCI space for the devices to + * access main memory */ + pci_ctrl[1].pitar1 = 0x0; + pci_ctrl[1].pibar1 = 0x0; + pci_ctrl[1].piebar1 = 0x0; + pci_ctrl[1].piwar1 = PIWAR_EN | PIWAR_PF | PIWAR_RTT_SNOOP | PIWAR_WTT_SNOOP | (__ilog2(gd->ram_size) - 1); + + hose->first_busno = pci_hose[0].last_busno + 1; + hose->last_busno = 0xff; + + /* PCI memory prefetch space */ + pci_set_region(hose->regions + 0, + CFG_PCI2_MEM_BASE, + CFG_PCI2_MEM_PHYS, + CFG_PCI2_MEM_SIZE, + PCI_REGION_MEM|PCI_REGION_PREFETCH); + + /* PCI memory space */ + pci_set_region(hose->regions + 1, + CFG_PCI2_MMIO_BASE, + CFG_PCI2_MMIO_PHYS, + CFG_PCI2_MMIO_SIZE, + PCI_REGION_MEM); + + /* PCI IO space */ + pci_set_region(hose->regions + 2, + CFG_PCI2_IO_BASE, + CFG_PCI2_IO_PHYS, + CFG_PCI2_IO_SIZE, + PCI_REGION_IO); + + /* System memory space */ + pci_set_region(hose->regions + 3, + CONFIG_PCI_SYS_MEM_BUS, + CONFIG_PCI_SYS_MEM_PHYS, + gd->ram_size, + PCI_REGION_MEM | PCI_REGION_MEMORY); + + hose->region_count = 4; + + pci_setup_indirect(hose, + (CFG_IMMR+0x8380), + (CFG_IMMR+0x8384)); + + pci_register_hose(hose); + + /* + * Write to Command register + */ + reg16 = 0xff; + dev = PCI_BDF(hose->first_busno, 0, 0); + pci_hose_read_config_word (hose, dev, PCI_COMMAND, ®16); + reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; + pci_hose_write_config_word(hose, dev, PCI_COMMAND, reg16); + + /* + * Clear non-reserved bits in status register. + */ + pci_hose_write_config_word(hose, dev, PCI_STATUS, 0xffff); + pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80); + pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08); + + /* + * Hose scan. + */ + hose->last_busno = pci_hose_scan(hose); +#endif + +} + +#ifdef CONFIG_OF_FLAT_TREE +void +ft_pci_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + + p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8500/bus-range", &len); + if (p != NULL) { + p[0] = pci_hose[0].first_busno; + p[1] = pci_hose[0].last_busno; + } + +#ifdef CONFIG_MPC83XX_PCI2 + p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8600/bus-range", &len); + if (p != NULL) { + p[0] = pci_hose[1].first_busno; + p[1] = pci_hose[1].last_busno; + } +#endif +} +#endif /* CONFIG_OF_FLAT_TREE */ +#endif /* CONFIG_PCI */ diff --git a/board/sbc8349/sbc8349.c b/board/sbc8349/sbc8349.c new file mode 100644 index 00000000000..4cd447e097f --- /dev/null +++ b/board/sbc8349/sbc8349.c @@ -0,0 +1,585 @@ +/* + * sbc8349.c -- WindRiver SBC8349 board support. + * Copyright (c) 2006-2007 Wind River Systems, Inc. + * + * Paul Gortmaker + * Based on board/mpc8349emds/mpc8349emds.c (and previous 834x releases.) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_SPD_EEPROM) +#include +#endif +#if defined(CONFIG_OF_FLAT_TREE) +#include +#endif + +int fixed_sdram(void); +void sdram_init(void); + +#if defined(CONFIG_DDR_ECC) && defined(CONFIG_MPC83XX) +void ddr_enable_ecc(unsigned int dram_size); +#endif + +#ifdef CONFIG_BOARD_EARLY_INIT_F +int board_early_init_f (void) +{ + return 0; +} +#endif + +#define ns2clk(ns) (ns / (1000000000 / CONFIG_8349_CLKIN) + 1) + +long int initdram (int board_type) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + puts("Initializing\n"); + + /* DDR SDRAM - Main SODIMM */ + im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR; +#if defined(CONFIG_SPD_EEPROM) + msize = spd_sdram(); +#else + msize = fixed_sdram(); +#endif + /* + * Initialize SDRAM if it is on local bus. + */ + sdram_init(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Initialize and enable DDR ECC. + */ + ddr_enable_ecc(msize * 1024 * 1024); +#endif + puts(" DDR RAM: "); + /* return total bus SDRAM size(bytes) -- DDR */ + return (msize * 1024 * 1024); +} + +#if !defined(CONFIG_SPD_EEPROM) +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + ************************************************************************/ +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + u32 msize = 0; + u32 ddr_size; + u32 ddr_size_log2; + + msize = CFG_DDR_SIZE; + for (ddr_size = msize << 20, ddr_size_log2 = 0; + (ddr_size > 1); + ddr_size = ddr_size>>1, ddr_size_log2++) { + if (ddr_size & 1) { + return -1; + } + } + im->sysconf.ddrlaw[0].bar = ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff); + im->sysconf.ddrlaw[0].ar = LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE); + +#if (CFG_DDR_SIZE != 256) +#warning Currently any ddr size other than 256 is not supported +#endif + im->ddr.csbnds[2].csbnds = 0x0000000f; + im->ddr.cs_config[2] = CFG_DDR_CONFIG; + + /* currently we use only one CS, so disable the other banks */ + im->ddr.cs_config[0] = 0; + im->ddr.cs_config[1] = 0; + im->ddr.cs_config[3] = 0; + + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + + im->ddr.sdram_cfg = + SDRAM_CFG_SREN +#if defined(CONFIG_DDR_2T_TIMING) + | SDRAM_CFG_2T_EN +#endif + | 2 << SDRAM_CFG_SDRAM_TYPE_SHIFT; +#if defined (CONFIG_DDR_32BIT) + /* for 32-bit mode burst length is 8 */ + im->ddr.sdram_cfg |= (SDRAM_CFG_32_BE | SDRAM_CFG_8_BE); +#endif + im->ddr.sdram_mode = CFG_DDR_MODE; + + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + udelay(200); + + /* enable DDR controller */ + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + return msize; +} +#endif/*!CFG_SPD_EEPROM*/ + + +int checkboard (void) +{ + puts("Board: Wind River SBC834x\n"); + return 0; +} + +/* + * if board is fitted with SDRAM + */ +#if defined(CFG_BR2_PRELIM) \ + && defined(CFG_OR2_PRELIM) \ + && defined(CFG_LBLAWBAR2_PRELIM) \ + && defined(CFG_LBLAWAR2_PRELIM) +/* + * Initialize SDRAM memory on the Local Bus. + */ + +void sdram_init(void) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile lbus83xx_t *lbc= &immap->lbus; + uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE; + + puts("\n SDRAM on Local Bus: "); + print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n"); + + /* + * Setup SDRAM Base and Option Registers, already done in cpu_init.c + */ + + /* setup mtrpt, lsrt and lbcr for LB bus */ + lbc->lbcr = CFG_LBC_LBCR; + lbc->mrtpr = CFG_LBC_MRTPR; + lbc->lsrt = CFG_LBC_LSRT; + asm("sync"); + + /* + * Configure the SDRAM controller Machine Mode Register. + */ + lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation */ + + lbc->lsdmr = CFG_LBC_LSDMR_1; /* 0x68636733; precharge all the banks */ + asm("sync"); + *sdram_addr = 0xff; + udelay(100); + + lbc->lsdmr = CFG_LBC_LSDMR_2; /* 0x48636733; auto refresh */ + asm("sync"); + /*1 times*/ + *sdram_addr = 0xff; + udelay(100); + /*2 times*/ + *sdram_addr = 0xff; + udelay(100); + /*3 times*/ + *sdram_addr = 0xff; + udelay(100); + /*4 times*/ + *sdram_addr = 0xff; + udelay(100); + /*5 times*/ + *sdram_addr = 0xff; + udelay(100); + /*6 times*/ + *sdram_addr = 0xff; + udelay(100); + /*7 times*/ + *sdram_addr = 0xff; + udelay(100); + /*8 times*/ + *sdram_addr = 0xff; + udelay(100); + + /* 0x58636733; mode register write operation */ + lbc->lsdmr = CFG_LBC_LSDMR_4; + asm("sync"); + *sdram_addr = 0xff; + udelay(100); + + lbc->lsdmr = CFG_LBC_LSDMR_5; /* 0x40636733; normal operation */ + asm("sync"); + *sdram_addr = 0xff; + udelay(100); +} +#else +void sdram_init(void) +{ + puts(" SDRAM on Local Bus: Disabled in config\n"); +} +#endif + +#if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD) +/* + * ECC user commands + */ +void ecc_print_status(void) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ddr83xx_t *ddr = &immap->ddr; + + printf("\nECC mode: %s\n\n", (ddr->sdram_cfg & SDRAM_CFG_ECC_EN) ? "ON" : "OFF"); + + /* Interrupts */ + printf("Memory Error Interrupt Enable:\n"); + printf(" Multiple-Bit Error Interrupt Enable: %d\n", + (ddr->err_int_en & ECC_ERR_INT_EN_MBEE) ? 1 : 0); + printf(" Single-Bit Error Interrupt Enable: %d\n", + (ddr->err_int_en & ECC_ERR_INT_EN_SBEE) ? 1 : 0); + printf(" Memory Select Error Interrupt Enable: %d\n\n", + (ddr->err_int_en & ECC_ERR_INT_EN_MSEE) ? 1 : 0); + + /* Error disable */ + printf("Memory Error Disable:\n"); + printf(" Multiple-Bit Error Disable: %d\n", + (ddr->err_disable & ECC_ERROR_DISABLE_MBED) ? 1 : 0); + printf(" Sinle-Bit Error Disable: %d\n", + (ddr->err_disable & ECC_ERROR_DISABLE_SBED) ? 1 : 0); + printf(" Memory Select Error Disable: %d\n\n", + (ddr->err_disable & ECC_ERROR_DISABLE_MSED) ? 1 : 0); + + /* Error injection */ + printf("Memory Data Path Error Injection Mask High/Low: %08lx %08lx\n", + ddr->data_err_inject_hi, ddr->data_err_inject_lo); + + printf("Memory Data Path Error Injection Mask ECC:\n"); + printf(" ECC Mirror Byte: %d\n", + (ddr->ecc_err_inject & ECC_ERR_INJECT_EMB) ? 1 : 0); + printf(" ECC Injection Enable: %d\n", + (ddr->ecc_err_inject & ECC_ERR_INJECT_EIEN) ? 1 : 0); + printf(" ECC Error Injection Mask: 0x%02x\n\n", + ddr->ecc_err_inject & ECC_ERR_INJECT_EEIM); + + /* SBE counter/threshold */ + printf("Memory Single-Bit Error Management (0..255):\n"); + printf(" Single-Bit Error Threshold: %d\n", + (ddr->err_sbe & ECC_ERROR_MAN_SBET) >> ECC_ERROR_MAN_SBET_SHIFT); + printf(" Single-Bit Error Counter: %d\n\n", + (ddr->err_sbe & ECC_ERROR_MAN_SBEC) >> ECC_ERROR_MAN_SBEC_SHIFT); + + /* Error detect */ + printf("Memory Error Detect:\n"); + printf(" Multiple Memory Errors: %d\n", + (ddr->err_detect & ECC_ERROR_DETECT_MME) ? 1 : 0); + printf(" Multiple-Bit Error: %d\n", + (ddr->err_detect & ECC_ERROR_DETECT_MBE) ? 1 : 0); + printf(" Single-Bit Error: %d\n", + (ddr->err_detect & ECC_ERROR_DETECT_SBE) ? 1 : 0); + printf(" Memory Select Error: %d\n\n", + (ddr->err_detect & ECC_ERROR_DETECT_MSE) ? 1 : 0); + + /* Capture data */ + printf("Memory Error Address Capture: 0x%08lx\n", ddr->capture_address); + printf("Memory Data Path Read Capture High/Low: %08lx %08lx\n", + ddr->capture_data_hi, ddr->capture_data_lo); + printf("Memory Data Path Read Capture ECC: 0x%02x\n\n", + ddr->capture_ecc & CAPTURE_ECC_ECE); + + printf("Memory Error Attributes Capture:\n"); + printf(" Data Beat Number: %d\n", + (ddr->capture_attributes & ECC_CAPT_ATTR_BNUM) >> ECC_CAPT_ATTR_BNUM_SHIFT); + printf(" Transaction Size: %d\n", + (ddr->capture_attributes & ECC_CAPT_ATTR_TSIZ) >> ECC_CAPT_ATTR_TSIZ_SHIFT); + printf(" Transaction Source: %d\n", + (ddr->capture_attributes & ECC_CAPT_ATTR_TSRC) >> ECC_CAPT_ATTR_TSRC_SHIFT); + printf(" Transaction Type: %d\n", + (ddr->capture_attributes & ECC_CAPT_ATTR_TTYP) >> ECC_CAPT_ATTR_TTYP_SHIFT); + printf(" Error Information Valid: %d\n\n", + ddr->capture_attributes & ECC_CAPT_ATTR_VLD); +} + +int do_ecc ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ddr83xx_t *ddr = &immap->ddr; + volatile u32 val; + u64 *addr, count, val64; + register u64 *i; + + if (argc > 4) { + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + if (argc == 2) { + if (strcmp(argv[1], "status") == 0) { + ecc_print_status(); + return 0; + } else if (strcmp(argv[1], "captureclear") == 0) { + ddr->capture_address = 0; + ddr->capture_data_hi = 0; + ddr->capture_data_lo = 0; + ddr->capture_ecc = 0; + ddr->capture_attributes = 0; + return 0; + } + } + + if (argc == 3) { + if (strcmp(argv[1], "sbecnt") == 0) { + val = simple_strtoul(argv[2], NULL, 10); + if (val > 255) { + printf("Incorrect Counter value, should be 0..255\n"); + return 1; + } + + val = (val << ECC_ERROR_MAN_SBEC_SHIFT); + val |= (ddr->err_sbe & ECC_ERROR_MAN_SBET); + + ddr->err_sbe = val; + return 0; + } else if (strcmp(argv[1], "sbethr") == 0) { + val = simple_strtoul(argv[2], NULL, 10); + if (val > 255) { + printf("Incorrect Counter value, should be 0..255\n"); + return 1; + } + + val = (val << ECC_ERROR_MAN_SBET_SHIFT); + val |= (ddr->err_sbe & ECC_ERROR_MAN_SBEC); + + ddr->err_sbe = val; + return 0; + } else if (strcmp(argv[1], "errdisable") == 0) { + val = ddr->err_disable; + + if (strcmp(argv[2], "+sbe") == 0) { + val |= ECC_ERROR_DISABLE_SBED; + } else if (strcmp(argv[2], "+mbe") == 0) { + val |= ECC_ERROR_DISABLE_MBED; + } else if (strcmp(argv[2], "+mse") == 0) { + val |= ECC_ERROR_DISABLE_MSED; + } else if (strcmp(argv[2], "+all") == 0) { + val |= (ECC_ERROR_DISABLE_SBED | + ECC_ERROR_DISABLE_MBED | + ECC_ERROR_DISABLE_MSED); + } else if (strcmp(argv[2], "-sbe") == 0) { + val &= ~ECC_ERROR_DISABLE_SBED; + } else if (strcmp(argv[2], "-mbe") == 0) { + val &= ~ECC_ERROR_DISABLE_MBED; + } else if (strcmp(argv[2], "-mse") == 0) { + val &= ~ECC_ERROR_DISABLE_MSED; + } else if (strcmp(argv[2], "-all") == 0) { + val &= ~(ECC_ERROR_DISABLE_SBED | + ECC_ERROR_DISABLE_MBED | + ECC_ERROR_DISABLE_MSED); + } else { + printf("Incorrect err_disable field\n"); + return 1; + } + + ddr->err_disable = val; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + return 0; + } else if (strcmp(argv[1], "errdetectclr") == 0) { + val = ddr->err_detect; + + if (strcmp(argv[2], "mme") == 0) { + val |= ECC_ERROR_DETECT_MME; + } else if (strcmp(argv[2], "sbe") == 0) { + val |= ECC_ERROR_DETECT_SBE; + } else if (strcmp(argv[2], "mbe") == 0) { + val |= ECC_ERROR_DETECT_MBE; + } else if (strcmp(argv[2], "mse") == 0) { + val |= ECC_ERROR_DETECT_MSE; + } else if (strcmp(argv[2], "all") == 0) { + val |= (ECC_ERROR_DETECT_MME | + ECC_ERROR_DETECT_MBE | + ECC_ERROR_DETECT_SBE | + ECC_ERROR_DETECT_MSE); + } else { + printf("Incorrect err_detect field\n"); + return 1; + } + + ddr->err_detect = val; + return 0; + } else if (strcmp(argv[1], "injectdatahi") == 0) { + val = simple_strtoul(argv[2], NULL, 16); + + ddr->data_err_inject_hi = val; + return 0; + } else if (strcmp(argv[1], "injectdatalo") == 0) { + val = simple_strtoul(argv[2], NULL, 16); + + ddr->data_err_inject_lo = val; + return 0; + } else if (strcmp(argv[1], "injectecc") == 0) { + val = simple_strtoul(argv[2], NULL, 16); + if (val > 0xff) { + printf("Incorrect ECC inject mask, should be 0x00..0xff\n"); + return 1; + } + val |= (ddr->ecc_err_inject & ~ECC_ERR_INJECT_EEIM); + + ddr->ecc_err_inject = val; + return 0; + } else if (strcmp(argv[1], "inject") == 0) { + val = ddr->ecc_err_inject; + + if (strcmp(argv[2], "en") == 0) + val |= ECC_ERR_INJECT_EIEN; + else if (strcmp(argv[2], "dis") == 0) + val &= ~ECC_ERR_INJECT_EIEN; + else + printf("Incorrect command\n"); + + ddr->ecc_err_inject = val; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + return 0; + } else if (strcmp(argv[1], "mirror") == 0) { + val = ddr->ecc_err_inject; + + if (strcmp(argv[2], "en") == 0) + val |= ECC_ERR_INJECT_EMB; + else if (strcmp(argv[2], "dis") == 0) + val &= ~ECC_ERR_INJECT_EMB; + else + printf("Incorrect command\n"); + + ddr->ecc_err_inject = val; + return 0; + } + } + + if (argc == 4) { + if (strcmp(argv[1], "test") == 0) { + addr = (u64 *)simple_strtoul(argv[2], NULL, 16); + count = simple_strtoul(argv[3], NULL, 16); + + if ((u32)addr % 8) { + printf("Address not alligned on double word boundary\n"); + return 1; + } + + disable_interrupts(); + icache_disable(); + + for (i = addr; i < addr + count; i++) { + /* enable injects */ + ddr->ecc_err_inject |= ECC_ERR_INJECT_EIEN; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + + /* write memory location injecting errors */ + *i = 0x1122334455667788ULL; + __asm__ __volatile__ ("sync"); + + /* disable injects */ + ddr->ecc_err_inject &= ~ECC_ERR_INJECT_EIEN; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + + /* read data, this generates ECC error */ + val64 = *i; + __asm__ __volatile__ ("sync"); + + /* disable errors for ECC */ + ddr->err_disable |= ~ECC_ERROR_ENABLE; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + + /* re-initialize memory, write the location again + * NOT injecting errors this time */ + *i = 0xcafecafecafecafeULL; + __asm__ __volatile__ ("sync"); + + /* enable errors for ECC */ + ddr->err_disable &= ECC_ERROR_ENABLE; + __asm__ __volatile__ ("sync"); + __asm__ __volatile__ ("isync"); + } + + icache_enable(); + enable_interrupts(); + + return 0; + } + } + + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; +} + +U_BOOT_CMD( + ecc, 4, 0, do_ecc, + "ecc - support for DDR ECC features\n", + "status - print out status info\n" + "ecc captureclear - clear capture regs data\n" + "ecc sbecnt - set Single-Bit Error counter\n" + "ecc sbethr - set Single-Bit Threshold\n" + "ecc errdisable - clear/set disable Memory Error Disable, flag:\n" + " [-|+]sbe - Single-Bit Error\n" + " [-|+]mbe - Multiple-Bit Error\n" + " [-|+]mse - Memory Select Error\n" + " [-|+]all - all errors\n" + "ecc errdetectclr - clear Memory Error Detect, flag:\n" + " mme - Multiple Memory Errors\n" + " sbe - Single-Bit Error\n" + " mbe - Multiple-Bit Error\n" + " mse - Memory Select Error\n" + " all - all errors\n" + "ecc injectdatahi - set Memory Data Path Error Injection Mask High\n" + "ecc injectdatalo - set Memory Data Path Error Injection Mask Low\n" + "ecc injectecc - set ECC Error Injection Mask\n" + "ecc inject - enable/disable error injection\n" + "ecc mirror - enable/disable mirror byte\n" + "ecc test - test mem region:\n" + " - enables injects\n" + " - writes pattern injecting errors\n" + " - disables injects\n" + " - reads pattern back, generates error\n" + " - re-inits memory" +); +#endif /* if defined(CONFIG_DDR_ECC) && defined(CONFIG_DDR_ECC_CMD) */ + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void +ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif diff --git a/board/sbc8349/u-boot.lds b/board/sbc8349/u-boot.lds new file mode 100644 index 00000000000..e32c0754cf6 --- /dev/null +++ b/board/sbc8349/u-boot.lds @@ -0,0 +1,125 @@ +/* + * Copyright (c) 2006 Wind River Systems, Inc. + * u-boot.lds for WindRiver SBC8349. + * + * Based on the MPC8349 u-boot.lds + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc83xx/start.o (.text) + *(.text) + *(.fixup) + *(.got1) + . = ALIGN(16); + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} +ENTRY(_start) diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c index 0d93f2e1ea4..108328a7f4e 100644 --- a/cpu/mpc83xx/spd_sdram.c +++ b/cpu/mpc83xx/spd_sdram.c @@ -440,10 +440,14 @@ long int spd_sdram() ddr->sdram_interval = ((refresh_clk & 0x3fff) << 16) | 0x100; debug("DDR:sdram_interval=0x%08x\n", ddr->sdram_interval); +#ifdef CFG_DDR_SDRAM_CLK_CNTL /* Optional platform specific value */ + ddr->sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL; +#else /* SS_EN = 0, source synchronous disable * CLK_ADJST = 0, MCK/MCK# is launched aligned with addr/cmd */ ddr->sdram_clk_cntl = 0x00000000; +#endif debug("DDR:sdram_clk_cntl=0x%08x\n", ddr->sdram_clk_cntl); asm("sync;isync"); diff --git a/doc/README.sbc8349 b/doc/README.sbc8349 new file mode 100644 index 00000000000..a0ac6388d60 --- /dev/null +++ b/doc/README.sbc8349 @@ -0,0 +1,99 @@ + + + U-Boot for Wind River SBC834x Boards + ==================================== + + +The Wind River SBC834x board is a 6U form factor (not CPCI) reference +design that uses the MPC8347E or MPC8349E processor. U-Boot support +for this board is heavily based on the existing U-Boot support for +Freescale MPC8349 reference boards. + +Support has been primarily tested on the SBC8349 version of the board, +although earlier versions were also tested on the SBC8347. The primary +difference in the two is the level of PCI functionality. + + http://www.windriver.com/products/OCD/SBC8347E_49E/ + + +Flash Details: +============== + +The flash type is intel 28F640Jx (4096x16) [one device]. Base address +is 0xFF80_0000 which is also where the Hardware Reset Configuration +Word (HRCW) is stored. Caution should be used to not overwrite the +HRCW, or "CF RCW" with a Wind River ICE will be required to restore +the HRCW and allow the board to enter background mode for further +steps in the flash process. + + +Restoring a corrupted or missing flash image: +============================================= + +Details for storing U-boot to flash using a Wind River ICE can be found +on page 19 of the board manual (request ERG-00328-001). The following +is a summary of that information: + + - Connect ICE and establish connection to it from WorkBench/OCD. + - Ensure you have background mode (BKM) in the OCD terminal window. + - Select the appropriate flash type (listed above) + - Prepare a u-boot image by using the Wind River Convert utility; + by using "Convert and Add file" on the ELF file from your build. + Convert from FFF0_0000 to FFFF_FFFF (or to FFF3_FFFF if you are + trying to preserve your old environment settings). + - Set the start address of the erase/flash process to FFF0_0000 + - Set the target RAM required to 64kB. + - Select sectors for erasing (see note on enviroment below) + - Select Erase and Reprogram. + +Note that some versions of the register files used with Workbench +would zero some TSEC registers, which inhibits ethernet operation +by u-boot when this register file is played to the target. Using +"INN" in the OCD terminal window instead of "IN" before the "GO" +will not play the register file, and allow u-boot to use the TSEC +interface while executed from the ICE "GO" command. + +Alternatively, you can locate the register file which will be named +WRS_SBC8349_PCT00328001.reg or similar) and "REM" out all the lines +beginning with "SCGA TSEC1" and "SCGA TSEC2". This allows you to +use all the remaining register file content. + +If you wish to preserve your prior U-Boot environment settings, +then convert (and erase to) 0xFFF3FFFF instead of 0xFFFFFFFF. +The size for converting (and erasing) must be at least as large +as u-boot.bin. + + +Updating U-Boot with U-Boot: +============================ + +This procedure is very similar to other boards that have u-boot installed. +Assuming that the network has been configured, and that the new u-boot.bin +has been copied to the TFTP server, the commands are: + + tftp 200000 u-boot.bin + protect off all + erase fff00000 fff3ffff + cp.b 200000 fff00000 3ffff + protect on all + + +PCI: +==== + +This board and U-Boot have been tested with PCI built in, on a SBC8349 +and confirmed that the "pci" command showed the intel e1000 that was +present in the PCI slot. Note that if a 33MHz 32bit card is inserted +in the slot, then the whole board will clock down to a 33MHz base +clock instead of the default 66MHz. This will change the baud clocks +and mess up your serial console output. If you want to use a 33MHz PCI +card, then you should build a U-Boot with #undef PCI_66M in the +include/configs/sbc8349.h and store this to flash prior to powering down +the board and inserting the 33MHz PCI card. + +By default PCI support is disabled to better support very early +revision MPC834x chips with possible PCI issues. Also PCI support is +untested on the sbc8347 variants at this point in time. + + + Paul Gortmaker, 01/2007 diff --git a/drivers/tsec.c b/drivers/tsec.c index 2524e4f6d2b..3f11eb03b41 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -381,6 +381,61 @@ uint mii_parse_sr(uint mii_reg, struct tsec_private * priv) return 0; } +/* + * Parse the BCM54xx status register for speed and duplex information. + * The linux sungem_phy has this information, but in a table format. + */ +uint mii_parse_BCM54xx_sr(uint mii_reg, struct tsec_private *priv) +{ + + switch((mii_reg & MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK) >> MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT){ + + case 1: + printf("Enet starting in 10BT/HD\n"); + priv->duplexity = 0; + priv->speed = 10; + break; + + case 2: + printf("Enet starting in 10BT/FD\n"); + priv->duplexity = 1; + priv->speed = 10; + break; + + case 3: + printf("Enet starting in 100BT/HD\n"); + priv->duplexity = 0; + priv->speed = 100; + break; + + case 5: + printf("Enet starting in 100BT/FD\n"); + priv->duplexity = 1; + priv->speed = 100; + break; + + case 6: + printf("Enet starting in 1000BT/HD\n"); + priv->duplexity = 0; + priv->speed = 1000; + break; + + case 7: + printf("Enet starting in 1000BT/FD\n"); + priv->duplexity = 1; + priv->speed = 1000; + break; + + default: + printf("Auto-neg error, defaulting to 10BT/HD\n"); + priv->duplexity = 0; + priv->speed = 10; + break; + } + + return 0; + +} /* Parse the 88E1011's status register for speed and duplex * information */ @@ -770,6 +825,34 @@ static void tsec_halt(struct eth_device *dev) phy_run_commands(priv, priv->phyinfo->shutdown); } +/* The 5411 id is 0x206070, the 5421 is 0x2060e0 */ +struct phy_info phy_info_BCM5461S = { + 0x02060c1, /* 5461 ID */ + "Broadcom BCM5461S", + 0, /* not clear to me what minor revisions we can shift away */ + (struct phy_cmd[]) { /* config */ + /* Reset and configure the PHY */ + {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, + {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, + {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {MIIM_CONTROL, MIIM_CONTROL_INIT, &mii_cr_init}, + {miim_end,} + }, + (struct phy_cmd[]) { /* startup */ + /* Status is read once to clear old link state */ + {MIIM_STATUS, miim_read, NULL}, + /* Auto-negotiate */ + {MIIM_STATUS, miim_read, &mii_parse_sr}, + /* Read the status */ + {MIIM_BCM54xx_AUXSTATUS, miim_read, &mii_parse_BCM54xx_sr}, + {miim_end,} + }, + (struct phy_cmd[]) { /* shutdown */ + {miim_end,} + }, +}; + struct phy_info phy_info_M88E1011S = { 0x01410c6, "Marvell 88E1011S", @@ -1112,6 +1195,7 @@ struct phy_info phy_info_dp83865 = { struct phy_info *phy_info[] = { &phy_info_cis8204, &phy_info_cis8201, + &phy_info_BCM5461S, &phy_info_M88E1011S, &phy_info_M88E1111S, &phy_info_M88E1145, diff --git a/drivers/tsec.h b/drivers/tsec.h index cee30037db0..422bc669229 100644 --- a/drivers/tsec.h +++ b/drivers/tsec.h @@ -109,6 +109,11 @@ #define MIIM_GBIT_CONTROL 0x9 #define MIIM_GBIT_CONTROL_INIT 0xe00 +/* Broadcom BCM54xx -- taken from linux sungem_phy */ +#define MIIM_BCM54xx_AUXSTATUS 0x19 +#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK 0x0700 +#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT 8 + /* Cicada Auxiliary Control/Status Register */ #define MIIM_CIS8201_AUX_CONSTAT 0x1c #define MIIM_CIS8201_AUXCONSTAT_INIT 0x0004 diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h new file mode 100644 index 00000000000..2e6685d90bc --- /dev/null +++ b/include/configs/sbc8349.h @@ -0,0 +1,744 @@ +/* + * WindRiver SBC8349 U-Boot configuration file. + * Copyright (c) 2006, 2007 Wind River Systems, Inc. + * + * Paul Gortmaker + * Based on the MPC8349EMDS config. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * sbc8349 board configuration file. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC834X 1 /* MPC834X family */ +#define CONFIG_MPC8349 1 /* MPC8349 specific */ +#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */ + +#undef CONFIG_PCI +/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */ +#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ + +#define PCI_66M +#ifdef PCI_66M +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#else +#define CONFIG_83XX_CLKIN 33000000 /* in Hz */ +#endif + +#ifndef CONFIG_SYS_CLK_FREQ +#ifdef PCI_66M +#define CONFIG_SYS_CLK_FREQ 66000000 +#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 +#else +#define CONFIG_SYS_CLK_FREQ 33000000 +#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 +#endif +#endif + +#define CFG_SCCR_INIT (SCCR_DEFAULT & (~SCCR_CLK_MASK)) +#define CFG_SCCR_TSEC1CM SCCR_TSEC1CM_1 /* TSEC1 clock setting */ +#define CFG_SCCR_TSEC2CM SCCR_TSEC2CM_1 /* TSEC2 clock setting */ +#define CFG_SCCR_ENCCM SCCR_ENCCM_3 /* ENC clock setting */ +#define CFG_SCCR_USBCM SCCR_USBCM_3 /* USB clock setting */ +#define CFG_SCCR_VAL ( CFG_SCCR_INIT \ + | CFG_SCCR_TSEC1CM \ + | CFG_SCCR_TSEC2CM \ + | CFG_SCCR_ENCCM \ + | CFG_SCCR_USBCM ) + +#undef CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ + +#define CFG_IMMR 0xE0000000 + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00000000 /* memtest region */ +#define CFG_MEMTEST_END 0x00100000 + +/* + * DDR Setup + */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ +#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ +#define CFG_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */ + +/* + * 32-bit data path mode. + * + * Please note that using this mode for devices with the real density of 64-bit + * effectively reduces the amount of available memory due to the effect of + * wrapping around while translating address to row/columns, for example in the + * 256MB module the upper 128MB get aliased with contents of the lower + * 128MB); normally this define should be used for devices with real 32-bit + * data path. + */ +#undef CONFIG_DDR_32BIT + +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) +#define CONFIG_DDR_2T_TIMING + +#if defined(CONFIG_SPD_EEPROM) +/* + * Determine DDR configuration from I2C interface. + */ +#define SPD_EEPROM_ADDRESS 0x52 /* DDR DIMM */ + +#else +/* + * Manually set up DDR parameters + * NB: manual DDR setup untested on sbc834x + */ +#define CFG_DDR_SIZE 256 /* MB */ +#define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) +#define CFG_DDR_TIMING_1 0x36332321 +#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ +#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ +#define CFG_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ + +#if defined(CONFIG_DDR_32BIT) +/* set burst length to 8 for 32-bit data path */ +#define CFG_DDR_MODE 0x00000023 /* DLL,normal,seq,4/2.5, 8 burst len */ +#else +/* the default burst length is 4 - for 64-bit data path */ +#define CFG_DDR_MODE 0x00000022 /* DLL,normal,seq,4/2.5, 4 burst len */ +#endif +#endif + +/* + * SDRAM on the Local Bus + */ +#define CFG_LBC_SDRAM_BASE 0x10000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 128 /* LBC SDRAM is 128MB */ + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFF800000 /* start of FLASH */ +#define CFG_FLASH_SIZE 8 /* flash size in MB */ +/* #define CFG_FLASH_USE_BUFFER_WRITE */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 32 bit port size */ \ + BR_V) /* valid */ + +#define CFG_OR0_PRELIM 0xFF806FF7 /* 8 MB flash size */ +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */ + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MID_FLASH_JUMP 0x7F000000 +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/ + +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Local Bus LCRR and LBCR regs + * LCRR: DLL bypass, Clock divider is 4 + * External Local Bus rate is + * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) +#define CFG_LBC_LBCR 0x00000000 + +#undef CFG_LB_SDRAM /* if board has SDRAM on local bus */ + +#ifdef CFG_LB_SDRAM +/* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/ +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port-size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 + * + * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * FIXME: the top 17 bits of BR2. + */ + +#define CFG_BR2_PRELIM 0xF0001861 /* Port-size=32bit, MSEL=SDRAM */ +#define CFG_LBLAWBAR2_PRELIM 0xF0000000 +#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64M */ + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 + */ + +#define CFG_OR2_PRELIM 0xFC006901 + +#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) +#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) +#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) +#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16)) +#define CFG_LBC_LSDMR_RFCR8 (5 << (31 - 16)) +#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) +#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) +#define CFG_LBC_LSDMR_PRETOACT6 (5 << (31 - 19)) +#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) +#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) +#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) +#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) +#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) +#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27)) +#define CFG_LBC_LSDMR_WRC3 (3 << (31 - 27)) +#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) +#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29)) +#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) + +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFEN \ + | CFG_LBC_LSDMR_BSMA1516 \ + | CFG_LBC_LSDMR_RFCR8 \ + | CFG_LBC_LSDMR_PRETOACT6 \ + | CFG_LBC_LSDMR_ACTTORW3 \ + | CFG_LBC_LSDMR_BL8 \ + | CFG_LBC_LSDMR_WRC3 \ + | CFG_LBC_LSDMR_CL3 \ + ) + +/* + * SDRAM Controller configuration sequence. + */ +#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_PCHALL) +#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_ARFRSH) +#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_MRW) +#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ + | CFG_LBC_LSDMR_OP_NORMAL) +#endif + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,8349@0" +#define OF_SOC "soc8349@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_CMD_TREE +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ +#define CFG_I2C1_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 +#define CFG_I2C_OFFSET CFG_I2C2_OFFSET +/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SPD_BUS_NUM... */ + +/* TSEC */ +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_MMIO_BASE 0x90000000 +#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE +#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xE2000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#define CFG_PCI2_MEM_BASE 0xA0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI2_MMIO_BASE 0xB0000000 +#define CFG_PCI2_MMIO_PHYS CFG_PCI2_MMIO_BASE +#define CFG_PCI2_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI2_IO_BASE 0x00000000 +#define CFG_PCI2_IO_PHYS 0xE2100000 +#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */ + +#if defined(CONFIG_PCI) + +#define PCI_64BIT +#define PCI_ONE_PCI1 +#if defined(PCI_64BIT) +#undef PCI_ALL_PCI1 +#undef PCI_TWO_PCI1 +#undef PCI_ONE_PCI1 +#endif + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xFIXME + #define PCI_ENET0_MEMADDR 0xFIXME + #define PCI_IDSEL_NUMBER 0xFIXME +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +/* + * TSEC configuration + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ + +#if defined(CONFIG_TSEC_ENET) +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MPC83XX_TSEC1 1 +#define CONFIG_MPC83XX_TSEC1_NAME "TSEC0" +#define CONFIG_MPC83XX_TSEC2 1 +#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1" +#define CONFIG_PHY_BCM5421S 1 +#define TSEC1_PHY_ADDR 0x19 +#define TSEC2_PHY_ADDR 0x1a +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CFG_RAMBOOT) +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_PCI \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) +#else +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C) \ + & \ + ~(CFG_CMD_ENV \ + | CFG_CMD_LOADS)) +#endif +#else +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + ) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII \ + ) +#endif +#endif + +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ + +#if 1 /*528/264*/ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X2 |\ + HRCWL_CORE_TO_CSB_2X1) +#elif 0 /*396/132*/ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_3X1) +#elif 0 /*264/132*/ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_2X1) +#elif 0 /*132/132*/ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_1X1) +#elif 0 /*264/264 */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN |\ + HRCWL_VCO_1X4 |\ + HRCWL_CORE_TO_CSB_1X1) +#endif + +#if defined(PCI_64BIT) +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_64_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII ) +#else +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_32_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII ) +#endif + +/* System IO Config */ +#define CFG_SICRH SICRH_TSOBI1 +#define CFG_SICRL SICRL_LDP_A + +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK + +/* #define CFG_HID0_FINAL (\ + HID0_ENABLE_INSTRUCTION_CACHE |\ + HID0_ENABLE_M_BIT |\ + HID0_ENABLE_ADDRESS_BROADCAST ) */ + + +#define CFG_HID2 HID2_HBE + +/* DDR @ 0x00000000 */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* PCI @ 0x80000000 */ +#ifdef CONFIG_PCI +#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#else +#define CFG_IBAT1L (0) +#define CFG_IBAT1U (0) +#define CFG_IBAT2L (0) +#define CFG_IBAT2U (0) +#endif + +#ifdef CONFIG_MPC83XX_PCI2 +#define CFG_IBAT3L (CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT3U (CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT4L (CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT4U (CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#else +#define CFG_IBAT3L (0) +#define CFG_IBAT3U (0) +#define CFG_IBAT4L (0) +#define CFG_IBAT4U (0) +#endif + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */ +#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) + +/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ +#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_ETHADDR 00:a0:1e:a0:13:8d +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:a0:1e:a0:13:8e +#endif + +#define CONFIG_IPADDR 192.168.1.234 + +#define CONFIG_HOSTNAME SBC8349 +#define CONFIG_ROOTPATH /tftpboot/rootfs +#define CONFIG_BOOTFILE uImage + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=sbc8349\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \ + "update=protect off fff00000 fff3ffff; " \ + "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ + "upd=run load;run update\0" \ + "fdtaddr=400000\0" \ + "fdtfile=sbc8349.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From a28899c910024a0226331df07207b1038c300c93 Mon Sep 17 00:00:00 2001 From: Emilian Medve Date: Tue, 30 Jan 2007 16:14:50 -0600 Subject: mpc83xx: Fix alternating tx error / tx buffer not ready bug in QE UEC The problem is not gcc4 but the code itself. The BD_STATUS() macro can't be used for busy-waiting since it strips the 'volatile' property from the bd variable. gcc3 was working by pure luck. This is a follow on patch to "Fix the UEC driver bug of QE" --- drivers/qe/uec.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c index aea455b8dc0..c416a67c832 100644 --- a/drivers/qe/uec.c +++ b/drivers/qe/uec.c @@ -1148,7 +1148,7 @@ static int uec_send(struct eth_device* dev, volatile void *buf, int len) /* Init TxBD */ BD_DATA_SET(bd, buf); BD_LENGTH_SET(bd, len); - status = BD_STATUS(bd); + status = bd->status; status &= BD_WRAP; status |= (TxBD_READY | TxBD_LAST); BD_STATUS_SET(bd, status); -- cgit v1.3.1 From f6f5f709e5c8e4564c4dfeecfdf2279244f9c83b Mon Sep 17 00:00:00 2001 From: Joakim Tjernlund Date: Wed, 31 Jan 2007 11:04:19 +0100 Subject: mpc83xx: Fix empty i2c reads/writes in fsl_i2c.c Fix empty i2c reads/writes, i2c_write(0x50, 0x00, 0, NULL, 0) which is used to se if an slave will ACK after receiving its address. Correct i2c probing to use this method as the old method could upset a slave as it wrote a data byte to it. Add a small delay in i2c_init() to let the controller shutdown any ongoing I2C activity. Signed-off-by: Joakim Tjernlund --- drivers/fsl_i2c.c | 27 ++++++++++++++------------- 1 file changed, 14 insertions(+), 13 deletions(-) (limited to 'drivers') diff --git a/drivers/fsl_i2c.c b/drivers/fsl_i2c.c index c92909608a3..ebae5af154e 100644 --- a/drivers/fsl_i2c.c +++ b/drivers/fsl_i2c.c @@ -58,6 +58,7 @@ i2c_init(int speed, int slaveadd) dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET); writeb(0, &dev->cr); /* stop I2C controller */ + udelay(5); /* let it shutdown in peace */ writeb(0x3F, &dev->fdr); /* set bus speed */ writeb(0x3F, &dev->dfsrr); /* set default filter */ writeb(slaveadd << 1, &dev->adr); /* write slave address */ @@ -191,15 +192,17 @@ __i2c_read(u8 *data, int length) int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) { - int i = 0; + int i = -1; /* signal error */ u8 *a = (u8*)&addr; if (i2c_wait4bus() >= 0 && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen - && i2c_write_addr(dev, I2C_READ_BIT, 1) != 0) { + && __i2c_write(&a[4 - alen], alen) == alen) + i = 0; /* No error so far */ + + if (length + && i2c_write_addr(dev, I2C_READ_BIT, 1) != 0) i = __i2c_read(data, length); - } writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); @@ -212,7 +215,7 @@ i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) { - int i = 0; + int i = -1; /* signal error */ u8 *a = (u8*)&addr; if (i2c_wait4bus() >= 0 @@ -232,16 +235,14 @@ i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) int i2c_probe(uchar chip) { - int tmp; - - /* - * Try to read the first location of the chip. The underlying - * driver doesn't appear to support sending just the chip address - * and looking for an back. + /* For unknow reason the controller will ACK when + * probing for a slave with the same address, so skip + * it. */ - udelay(10000); + if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1)) + return -1; - return i2c_read(chip, 0, 1, (uchar *)&tmp, 1); + return i2c_read(chip, 0, 0, NULL, 0); } uchar -- cgit v1.3.1 From 647d3c3eed0da1d1505eecabe0b0fab96f956e68 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 4 Mar 2007 01:36:05 +0100 Subject: Some code cleanup. --- board/mpc7448hpc2/mpc7448hpc2.c | 2 +- board/mpc7448hpc2/tsi108_init.c | 24 +++++++------- cpu/74xx_7xx/cpu.c | 4 +-- cpu/ppc4xx/44x_spd_ddr2.c | 10 +++--- cpu/ppc4xx/start.S | 72 ++++++++++++++++++++--------------------- doc/README.mpc7448hpc2 | 25 +++++++------- drivers/tsi108_i2c.c | 37 +++++++-------------- include/configs/mpc7448hpc2.h | 2 +- 8 files changed, 80 insertions(+), 96 deletions(-) (limited to 'drivers') diff --git a/board/mpc7448hpc2/mpc7448hpc2.c b/board/mpc7448hpc2/mpc7448hpc2.c index d4a047c1d6f..63c99de1756 100644 --- a/board/mpc7448hpc2/mpc7448hpc2.c +++ b/board/mpc7448hpc2/mpc7448hpc2.c @@ -47,7 +47,7 @@ int display_mem_map (void); void after_reloc (ulong dest_addr) { DECLARE_GLOBAL_DATA_PTR; - + /* * Jump to the main U-Boot board init code */ diff --git a/board/mpc7448hpc2/tsi108_init.c b/board/mpc7448hpc2/tsi108_init.c index e3b09cfad36..8a7efef7723 100644 --- a/board/mpc7448hpc2/tsi108_init.c +++ b/board/mpc7448hpc2/tsi108_init.c @@ -179,7 +179,7 @@ int board_early_init_r (void) ulong temp, i; ulong reg_val; volatile ulong *reg_ptr; - + reg_ptr = (ulong *) (CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + 0x900); @@ -300,7 +300,7 @@ int board_early_init_r (void) out32 (CFG_TSI108_CSR_BASE + TSI108_HLP_REG_OFFSET + HLP_B3_CTRL1, 0x7C0F2000); __asm__ __volatile__ ("sync"); - + /* * Set new value for PB_OCN_BAR1: switch from BOOT to LUT mode. * value for PB_OCN_BAR1: (BA-0xE000_0000 + size 512MB + ENable) @@ -312,7 +312,7 @@ int board_early_init_r (void) /* Make sure that OCN_BAR2 decoder is set (to allow following * immediate read from SDRAM) */ - + temp = in32(CFG_TSI108_CSR_BASE + TSI108_PB_REG_OFFSET + PB_OCN_BAR1); __asm__ __volatile__ ("sync"); @@ -327,11 +327,11 @@ int board_early_init_r (void) * and enable all HLP banks and not just HLP 0 as is being done for * Taiga Rev. 2. */ - + env_init (); #ifndef DISABLE_PBM - + /* * For IBM processors we have to set Address-Only commands generated * by PBM that are different from ones set after reset. @@ -475,10 +475,10 @@ int board_early_init_r (void) for (i = 0; i < 32; i++) { *reg_ptr++ = reg_val; /* P2O_BAR3_LUTx */ - + /* P2O_BAR3_LUT_UPPERx : Set data swapping mode for PBM (byte swapping) */ - *reg_ptr++ = 0; - + *reg_ptr++ = 0; + /* offset = 16MB, address translation is enabled to allow byte swapping */ reg_val += 0x01000000; } @@ -507,7 +507,7 @@ int board_early_init_r (void) #endif /* !DISABLE_PBM */ -#ifdef ENABLE_PCI_CSR_BAR +#ifdef ENABLE_PCI_CSR_BAR /* open if required access to Tsi108 CSRs from the PCI/X bus */ /* enable BAR0 on the PCI/X bus */ reg_val = in32(CFG_TSI108_CSR_BASE + @@ -528,7 +528,7 @@ int board_early_init_r (void) /* * Finally enable PCI/X Bus Master and Memory Space access */ - + reg_val = in32(CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR); reg_val |= 0x06; out32 (CFG_TSI108_CSR_BASE + TSI108_PCI_REG_OFFSET + PCI_CSR, reg_val); @@ -555,7 +555,7 @@ int board_early_init_r (void) * Ensure that Machine Check exception is enabled * We need it to support PCI Bus probing (configuration reads) */ - + reg_val = mfmsr (); mtmsr(reg_val | MSR_ME); @@ -631,7 +631,7 @@ int misc_init_r (void) * thing done with regards to enabling diabling the cache. * So this seems like a good place to print all this information */ - + printf ("CACHE: "); switch (get_cpu_type()) { case CPU_7447A: diff --git a/cpu/74xx_7xx/cpu.c b/cpu/74xx_7xx/cpu.c index 84d5da3116b..9c8998b604e 100644 --- a/cpu/74xx_7xx/cpu.c +++ b/cpu/74xx_7xx/cpu.c @@ -308,9 +308,9 @@ ft_cpu_setup (void *blob, bd_t *bd) u32 *p; ulong clock; int len; - + clock = bd->bi_busfreq; - + p = ft_get_prop (blob, "/cpus/" OF_CPU "/bus-frequency", &len); if (p != NULL) *p = cpu_to_be32 (clock); diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 35b23152f3b..da50985c4c8 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -168,8 +168,8 @@ static void program_codt(unsigned long *dimm_populated, static void program_mode(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t *selected_cas, - int *write_recovery); + ddr_cas_id_t *selected_cas, + int *write_recovery); static void program_tr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks); @@ -185,7 +185,7 @@ static void program_copt1(unsigned long *dimm_populated, static void program_initplr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t selected_cas, + ddr_cas_id_t selected_cas, int write_recovery); static unsigned long is_ecc_enabled(void); static void program_ecc(unsigned long *dimm_populated, @@ -1110,7 +1110,7 @@ static void program_codt(unsigned long *dimm_populated, modt3 = 0x00000000; } } - } else { + } else { codt |= SDRAM_CODT_DQS_2_5_V_DDR1; modt0 = 0x00000000; modt1 = 0x00000000; @@ -1149,7 +1149,7 @@ static void program_codt(unsigned long *dimm_populated, static void program_initplr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks, - ddr_cas_id_t selected_cas, + ddr_cas_id_t selected_cas, int write_recovery) { u32 cas = 0; diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 24b30dfe716..3fa52bd75a9 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -1858,11 +1858,11 @@ pll_wait: #endif /* CONFIG_405EP */ #if defined(CONFIG_440) -#define function_prolog(func_name) .text; \ +#define function_prolog(func_name) .text; \ .align 2; \ .globl func_name; \ func_name: -#define function_epilog(func_name) .type func_name,@function; \ +#define function_epilog(func_name) .type func_name,@function; \ .size func_name,.-func_name /*----------------------------------------------------------------------------+ @@ -1916,43 +1916,43 @@ pll_wait: /*----------------------------------------------------------------------------+ | dcbz_area. +----------------------------------------------------------------------------*/ - function_prolog(dcbz_area) - rlwinm. r5,r4,0,27,31 - rlwinm r5,r4,27,5,31 - beq ..d_ra2 - addi r5,r5,0x0001 -..d_ra2:mtctr r5 -..d_ag2:dcbz r0,r3 - addi r3,r3,32 - bdnz ..d_ag2 - sync - blr - function_epilog(dcbz_area) + function_prolog(dcbz_area) + rlwinm. r5,r4,0,27,31 + rlwinm r5,r4,27,5,31 + beq ..d_ra2 + addi r5,r5,0x0001 +..d_ra2:mtctr r5 +..d_ag2:dcbz r0,r3 + addi r3,r3,32 + bdnz ..d_ag2 + sync + blr + function_epilog(dcbz_area) /*----------------------------------------------------------------------------+ | dflush. Assume 32K at vector address is cachable. +----------------------------------------------------------------------------*/ - function_prolog(dflush) - mfmsr r9 - rlwinm r8,r9,0,15,13 - rlwinm r8,r8,0,17,15 - mtmsr r8 - addi r3,r0,0x0000 - mtspr dvlim,r3 - mfspr r3,ivpr - addi r4,r0,1024 - mtctr r4 + function_prolog(dflush) + mfmsr r9 + rlwinm r8,r9,0,15,13 + rlwinm r8,r8,0,17,15 + mtmsr r8 + addi r3,r0,0x0000 + mtspr dvlim,r3 + mfspr r3,ivpr + addi r4,r0,1024 + mtctr r4 ..dflush_loop: - lwz r6,0x0(r3) - addi r3,r3,32 - bdnz ..dflush_loop - addi r3,r3,-32 - mtctr r4 -..ag: dcbf r0,r3 - addi r3,r3,-32 - bdnz ..ag - sync - mtmsr r9 - blr - function_epilog(dflush) + lwz r6,0x0(r3) + addi r3,r3,32 + bdnz ..dflush_loop + addi r3,r3,-32 + mtctr r4 +..ag: dcbf r0,r3 + addi r3,r3,-32 + bdnz ..ag + sync + mtmsr r9 + blr + function_epilog(dflush) #endif /* CONFIG_440 */ diff --git a/doc/README.mpc7448hpc2 b/doc/README.mpc7448hpc2 index 0e40e39269b..8659e83673b 100644 --- a/doc/README.mpc7448hpc2 +++ b/doc/README.mpc7448hpc2 @@ -92,7 +92,7 @@ SW2[1-6]: CPU core frequency CPU Core Frequency (MHz) Bus Frequency 123456 100 133 167 200 Ratio - + ------ SW2=101100 500 667 833 1000 5x SW2=100100 550 733 917 1100 5.5x @@ -109,43 +109,43 @@ hardware specifications for more information. SW2[7-8]: Bus Protocol and CPU Reset Option - 7 + 7 - SW2=0 System bus uses MPX bus protocol SW2=1 System bus uses 60x bus protocol - 8 + 8 - SW2=0 TSI108 can cause CPU reset SW2=1 TSI108 can not cause CPU reset SW3[1-8] system options - 123 + 123 --- SW3=xxx Connected to GPIO[0:2] on TSI108 - 4 + 4 - SW3=0 CPU boots from low half of flash SW3=1 CPU boots from high half of flash - 5 + 5 - SW3=0 SATA and slot2 connected to PCI bus SW3=1 Only slot1 connected to PCI bus - 6 + 6 - SW3=0 USB connected to PCI bus SW3=1 USB disconnected from PCI bus - 7 + 7 - SW3=0 Flash is write protected SW3=1 Flash is NOT write protected - 8 + 8 - SW3=0 CPU will boot from flash SW3=1 CPU will boot from PromJet @@ -166,20 +166,19 @@ SW4[4-6]: DDR2 SDRAM frequency Bus Frequency (MHz) --- SW4=000 external clock - SW4=011 system clock + SW4=011 system clock SW4=100 133 SW4=101 166 SW4=110 200 others reserved SW4[7-8]: PCI/PCI-X frequency control - 7 + 7 - SW4=0 PCI/PCI-X bus operates normally SW4=1 PCI bus forced to PCI-33 mode - 8 + 8 - SW4=0 PCI-X mode at 133 MHz allowed SW4=1 PCI-X mode limited to 100 MHz - diff --git a/drivers/tsi108_i2c.c b/drivers/tsi108_i2c.c index c100cb82470..eb52cb66c96 100644 --- a/drivers/tsi108_i2c.c +++ b/drivers/tsi108_i2c.c @@ -82,15 +82,10 @@ static int i2c_read_byte ( /* Wait until operation completed */ do { /* Read I2C operation status */ - temp = - *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + - I2C_CNTRL2); - - if (0 == - (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) - { - if (0 == - (temp & + temp = *(u32 *) (CFG_TSI108_CSR_BASE + chan_offset + I2C_CNTRL2); + + if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_START))) { + if (0 == (temp & (I2C_CNTRL2_I2C_CFGERR | I2C_CNTRL2_I2C_TO_ERR)) ) { @@ -152,9 +147,7 @@ int i2c_read (uchar chip_addr, uint byte_addr, int alen, /* Check for valid I2C address */ if (chip_addr <= 0x7F && (byte_addr + len) <= (0x01 << (alen * 8))) { while (len--) { - op_status = - i2c_read_byte(i2c_if, chip_addr, byte_addr++, - buffer++); + op_status = i2c_read_byte(i2c_if, chip_addr, byte_addr++, buffer++); if (TSI108_I2C_SUCCESS != op_status) { DPRINT (("I2C read_byte() failed: 0x%02x (%d left)\n", op_status, len)); @@ -182,10 +175,7 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Check if I2C operation is in progress */ temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); - if (0 == - (temp & - (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) - { + if (0 == (temp & (I2C_CNTRL2_RD_STATUS | I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) { /* Place data into the I2C Tx Register */ *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_TX_DATA) = (u32) * buffer; @@ -200,7 +190,7 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Issue the write command (at this moment all other parameters * are 0 (size = 1 byte, lane = 0) */ - + *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2) = (I2C_CNTRL2_START); @@ -209,15 +199,10 @@ static int i2c_write_byte (uchar chip_addr,/* I2C device address on the bus */ /* Wait until operation completed */ do { /* Read I2C operation status */ - temp = - *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + - I2C_CNTRL2); - - if (0 == - (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) - { - if (0 == - (temp & + temp = *(u32 *) (CFG_TSI108_CSR_BASE + TSI108_I2C_OFFSET + I2C_CNTRL2); + + if (0 == (temp & (I2C_CNTRL2_WR_STATUS | I2C_CNTRL2_START))) { + if (0 == (temp & (I2C_CNTRL2_I2C_CFGERR | I2C_CNTRL2_I2C_TO_ERR))) { op_status = TSI108_I2C_SUCCESS; diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h index eb528dfaf4b..243a3f6c8fc 100644 --- a/include/configs/mpc7448hpc2.h +++ b/include/configs/mpc7448hpc2.h @@ -285,7 +285,7 @@ /* PCI view of System Memory */ #define CFG_PCI_MEMORY_BUS 0x00000000 #define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 /* PCI Memory Space */ #define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS) -- cgit v1.3.1 From df548d3c3e2bbc40258713167859ffc2ce99a900 Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Sun, 19 Nov 2006 18:06:53 +0100 Subject: AVR32: Resource management rewrite Rewrite the resource management code (i.e. I/O memory, clock gating, gpio) so it doesn't depend on any global state. This is necessary because this code is heavily used before relocation to RAM, so we can't write to any global variables. As an added bonus, this makes u-boot's memory footprint a bit smaller, although some functionality has been left out; all clocks are enabled all the time, and there's no checking for gpio line conflicts. Signed-off-by: Haavard Skinnemoen --- board/atmel/atstk1000/atstk1000.c | 13 + cpu/at32ap/Makefile | 2 +- cpu/at32ap/at32ap7000/Makefile | 2 +- cpu/at32ap/at32ap7000/devices.c | 448 --------------------------- cpu/at32ap/at32ap7000/gpio.c | 77 +++++ cpu/at32ap/at32ap7000/hebi.c | 38 --- cpu/at32ap/cpu.c | 64 +++- cpu/at32ap/device.c | 126 -------- cpu/at32ap/hsdramc.c | 43 +-- cpu/at32ap/hsdramc1.h | 8 +- cpu/at32ap/hsmc3.h | 8 +- cpu/at32ap/interrupts.c | 11 +- cpu/at32ap/pio.c | 90 ++---- cpu/at32ap/pio2.h | 8 +- cpu/at32ap/pm.c | 127 +------- cpu/at32ap/sm.h | 8 +- drivers/atmel_usart.c | 48 +-- drivers/atmel_usart.h | 8 +- include/asm-avr32/arch-at32ap7000/clk.h | 58 ++++ include/asm-avr32/arch-at32ap7000/gpio.h | 210 +++++++++++++ include/asm-avr32/arch-at32ap7000/hmatrix2.h | 8 +- include/asm-avr32/arch-at32ap7000/platform.h | 146 --------- include/asm-avr32/global_data.h | 2 - include/configs/atstk1002.h | 7 +- lib_avr32/avr32_linux.c | 4 +- lib_avr32/board.c | 1 + 26 files changed, 524 insertions(+), 1041 deletions(-) delete mode 100644 cpu/at32ap/at32ap7000/devices.c create mode 100644 cpu/at32ap/at32ap7000/gpio.c delete mode 100644 cpu/at32ap/at32ap7000/hebi.c delete mode 100644 cpu/at32ap/device.c create mode 100644 include/asm-avr32/arch-at32ap7000/clk.h create mode 100644 include/asm-avr32/arch-at32ap7000/gpio.h delete mode 100644 include/asm-avr32/arch-at32ap7000/platform.h (limited to 'drivers') diff --git a/board/atmel/atstk1000/atstk1000.c b/board/atmel/atstk1000/atstk1000.c index 4d737d293ad..8210bc60e80 100644 --- a/board/atmel/atstk1000/atstk1000.c +++ b/board/atmel/atstk1000/atstk1000.c @@ -23,6 +23,8 @@ #include #include +#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -40,6 +42,17 @@ static const struct sdram_info sdram = { .txsr = 5, }; +int board_early_init_f(void) +{ + /* Set the SDRAM_ENABLE bit in the HEBI SFR */ + hmatrix2_writel(SFR4, 1 << 1); + + gpio_enable_ebi(); + gpio_enable_usart1(); + + return 0; +} + void board_init_memories(void) { gd->sdram_size = sdram_init(&sdram); diff --git a/cpu/at32ap/Makefile b/cpu/at32ap/Makefile index f62ec8bc9b2..3f1bb07b3e2 100644 --- a/cpu/at32ap/Makefile +++ b/cpu/at32ap/Makefile @@ -30,7 +30,7 @@ LIB := $(obj)lib$(CPU).a START := start.o SOBJS := entry.o COBJS := cpu.o hsdramc.o exception.o cache.o -COBJS += interrupts.o device.o pm.o pio.o +COBJS += interrupts.o pio.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) START := $(addprefix $(obj),$(START)) diff --git a/cpu/at32ap/at32ap7000/Makefile b/cpu/at32ap/at32ap7000/Makefile index 2ed74d2508c..d2767121184 100644 --- a/cpu/at32ap/at32ap7000/Makefile +++ b/cpu/at32ap/at32ap7000/Makefile @@ -24,7 +24,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)lib$(SOC).a -COBJS := hebi.o devices.o +COBJS := gpio.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/cpu/at32ap/at32ap7000/devices.c b/cpu/at32ap/at32ap7000/devices.c deleted file mode 100644 index 8b216e906a2..00000000000 --- a/cpu/at32ap/at32ap7000/devices.c +++ /dev/null @@ -1,448 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#include - -#include -#include - -#include "../sm.h" - -#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0])) - -const struct clock_domain chip_clock[] = { - [CLOCK_CPU] = { - .reg = SM_PM_CPU_MASK, - .id = CLOCK_CPU, - .bridge = NO_DEVICE, - }, - [CLOCK_HSB] = { - .reg = SM_PM_HSB_MASK, - .id = CLOCK_HSB, - .bridge = NO_DEVICE, - }, - [CLOCK_PBA] = { - .reg = SM_PM_PBA_MASK, - .id = CLOCK_PBA, - .bridge = DEVICE_PBA_BRIDGE, - }, - [CLOCK_PBB] = { - .reg = SM_PM_PBB_MASK, - .id = CLOCK_PBB, - .bridge = DEVICE_PBB_BRIDGE, - }, -}; - -static const struct resource hebi_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 0 }, - }, - }, { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 13 }, - }, - }, { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 14 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 27, DEVICE_PIOE, GPIO_FUNC_A, 0 }, - }, - }, -}; -static const struct resource pba_bridge_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 1 }, - } - }, { - .type = RESOURCE_CLOCK, - .u = { - /* HSB-HSB Bridge */ - .clock = { CLOCK_HSB, 4 }, - }, - }, -}; -static const struct resource pbb_bridge_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 2 }, - }, - }, -}; -static const struct resource hramc_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 3 }, - }, - }, -}; -static const struct resource pioa_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 10 }, - }, - }, -}; -static const struct resource piob_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 11 }, - }, - }, -}; -static const struct resource pioc_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 12 }, - }, - }, -}; -static const struct resource piod_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 13 }, - }, - }, -}; -static const struct resource pioe_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 14 }, - }, - }, -}; -static const struct resource sm_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 0 }, - }, - }, -}; -static const struct resource intc_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 1 }, - }, - }, -}; -static const struct resource hmatrix_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 2 }, - }, - }, -}; -#if defined(CFG_HPDC) -static const struct resource hpdc_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 16 }, - }, - }, -}; -#endif -#if defined(CFG_MACB0) -static const struct resource macb0_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 8 }, - }, - }, { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 6 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 19, DEVICE_PIOC, GPIO_FUNC_A, 0 }, - }, - }, -}; -#endif -#if defined(CFG_MACB1) -static const struct resource macb1_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 9 }, - }, - }, { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 7 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 12, DEVICE_PIOC, GPIO_FUNC_B, 19 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 14, DEVICE_PIOD, GPIO_FUNC_B, 2 }, - }, - }, -}; -#endif -#if defined(CFG_LCDC) -static const struct resource lcdc_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 7 }, - }, - }, -}; -#endif -#if defined(CFG_USART0) -static const struct resource usart0_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 3 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 2, DEVICE_PIOA, GPIO_FUNC_B, 8 }, - }, - }, -}; -#endif -#if defined(CFG_USART1) -static const struct resource usart1_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 4 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 2, DEVICE_PIOA, GPIO_FUNC_A, 17 }, - }, - }, -}; -#endif -#if defined(CFG_USART2) -static const struct resource usart2_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 5 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 26 }, - }, - }, -}; -#endif -#if defined(CFG_USART3) -static const struct resource usart3_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBA, 6 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 2, DEVICE_PIOB, GPIO_FUNC_B, 17 }, - }, - }, -}; -#endif -#if defined(CFG_MMCI) -static const struct resource mmci_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_PBB, 9 }, - }, - }, { - .type = RESOURCE_GPIO, - .u = { - .gpio = { 6, DEVICE_PIOA, GPIO_FUNC_A, 10 }, - }, - }, -}; -#endif -#if defined(CFG_DMAC) -static const struct resource dmac_resource[] = { - { - .type = RESOURCE_CLOCK, - .u = { - .clock = { CLOCK_HSB, 10 }, - }, - }, -}; -#endif - -const struct device chip_device[] = { - [DEVICE_HEBI] = { - .regs = (void *)HSMC_BASE, - .nr_resources = ARRAY_SIZE(hebi_resource), - .resource = hebi_resource, - }, - [DEVICE_PBA_BRIDGE] = { - .nr_resources = ARRAY_SIZE(pba_bridge_resource), - .resource = pba_bridge_resource, - }, - [DEVICE_PBB_BRIDGE] = { - .nr_resources = ARRAY_SIZE(pbb_bridge_resource), - .resource = pbb_bridge_resource, - }, - [DEVICE_HRAMC] = { - .nr_resources = ARRAY_SIZE(hramc_resource), - .resource = hramc_resource, - }, - [DEVICE_PIOA] = { - .regs = (void *)PIOA_BASE, - .nr_resources = ARRAY_SIZE(pioa_resource), - .resource = pioa_resource, - }, - [DEVICE_PIOB] = { - .regs = (void *)PIOB_BASE, - .nr_resources = ARRAY_SIZE(piob_resource), - .resource = piob_resource, - }, - [DEVICE_PIOC] = { - .regs = (void *)PIOC_BASE, - .nr_resources = ARRAY_SIZE(pioc_resource), - .resource = pioc_resource, - }, - [DEVICE_PIOD] = { - .regs = (void *)PIOD_BASE, - .nr_resources = ARRAY_SIZE(piod_resource), - .resource = piod_resource, - }, - [DEVICE_PIOE] = { - .regs = (void *)PIOE_BASE, - .nr_resources = ARRAY_SIZE(pioe_resource), - .resource = pioe_resource, - }, - [DEVICE_SM] = { - .regs = (void *)SM_BASE, - .nr_resources = ARRAY_SIZE(sm_resource), - .resource = sm_resource, - }, - [DEVICE_INTC] = { - .regs = (void *)INTC_BASE, - .nr_resources = ARRAY_SIZE(intc_resource), - .resource = intc_resource, - }, - [DEVICE_HMATRIX] = { - .regs = (void *)HMATRIX_BASE, - .nr_resources = ARRAY_SIZE(hmatrix_resource), - .resource = hmatrix_resource, - }, -#if defined(CFG_HPDC) - [DEVICE_HPDC] = { - .nr_resources = ARRAY_SIZE(hpdc_resource), - .resource = hpdc_resource, - }, -#endif -#if defined(CFG_MACB0) - [DEVICE_MACB0] = { - .regs = (void *)MACB0_BASE, - .nr_resources = ARRAY_SIZE(macb0_resource), - .resource = macb0_resource, - }, -#endif -#if defined(CFG_MACB1) - [DEVICE_MACB1] = { - .regs = (void *)MACB1_BASE, - .nr_resources = ARRAY_SIZE(macb1_resource), - .resource = macb1_resource, - }, -#endif -#if defined(CFG_LCDC) - [DEVICE_LCDC] = { - .nr_resources = ARRAY_SIZE(lcdc_resource), - .resource = lcdc_resource, - }, -#endif -#if defined(CFG_USART0) - [DEVICE_USART0] = { - .regs = (void *)USART0_BASE, - .nr_resources = ARRAY_SIZE(usart0_resource), - .resource = usart0_resource, - }, -#endif -#if defined(CFG_USART1) - [DEVICE_USART1] = { - .regs = (void *)USART1_BASE, - .nr_resources = ARRAY_SIZE(usart1_resource), - .resource = usart1_resource, - }, -#endif -#if defined(CFG_USART2) - [DEVICE_USART2] = { - .regs = (void *)USART2_BASE, - .nr_resources = ARRAY_SIZE(usart2_resource), - .resource = usart2_resource, - }, -#endif -#if defined(CFG_USART3) - [DEVICE_USART3] = { - .regs = (void *)USART3_BASE, - .nr_resources = ARRAY_SIZE(usart3_resource), - .resource = usart3_resource, - }, -#endif -#if defined(CFG_MMCI) - [DEVICE_MMCI] = { - .regs = (void *)MMCI_BASE, - .nr_resources = ARRAY_SIZE(mmci_resource), - .resource = mmci_resource, - }, -#endif -#if defined(CFG_DMAC) - [DEVICE_DMAC] = { - .regs = (void *)DMAC_BASE, - .nr_resources = ARRAY_SIZE(dmac_resource), - .resource = dmac_resource, - }, -#endif -}; diff --git a/cpu/at32ap/at32ap7000/gpio.c b/cpu/at32ap/at32ap7000/gpio.c new file mode 100644 index 00000000000..a5d3ea65d96 --- /dev/null +++ b/cpu/at32ap/at32ap7000/gpio.c @@ -0,0 +1,77 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include + +#include + +/* + * Lots of small functions here. We depend on --gc-sections getting + * rid of the ones we don't need. + */ +void gpio_enable_ebi(void) +{ +#ifdef CFG_HSDRAMC +#ifndef CFG_SDRAM_16BIT + gpio_select_periph_A(GPIO_PIN_PE0, 0); + gpio_select_periph_A(GPIO_PIN_PE1, 0); + gpio_select_periph_A(GPIO_PIN_PE2, 0); + gpio_select_periph_A(GPIO_PIN_PE3, 0); + gpio_select_periph_A(GPIO_PIN_PE4, 0); + gpio_select_periph_A(GPIO_PIN_PE5, 0); + gpio_select_periph_A(GPIO_PIN_PE6, 0); + gpio_select_periph_A(GPIO_PIN_PE7, 0); + gpio_select_periph_A(GPIO_PIN_PE8, 0); + gpio_select_periph_A(GPIO_PIN_PE9, 0); + gpio_select_periph_A(GPIO_PIN_PE10, 0); + gpio_select_periph_A(GPIO_PIN_PE11, 0); + gpio_select_periph_A(GPIO_PIN_PE12, 0); + gpio_select_periph_A(GPIO_PIN_PE13, 0); + gpio_select_periph_A(GPIO_PIN_PE14, 0); + gpio_select_periph_A(GPIO_PIN_PE15, 0); +#endif + gpio_select_periph_A(GPIO_PIN_PE26, 0); +#endif +} + +void gpio_enable_usart0(void) +{ + gpio_select_periph_B(GPIO_PIN_PA8, 0); + gpio_select_periph_B(GPIO_PIN_PA9, 0); +} + +void gpio_enable_usart1(void) +{ + gpio_select_periph_A(GPIO_PIN_PA17, 0); + gpio_select_periph_A(GPIO_PIN_PA18, 0); +} + +void gpio_enable_usart2(void) +{ + gpio_select_periph_B(GPIO_PIN_PB26, 0); + gpio_select_periph_B(GPIO_PIN_PB27, 0); +} + +void gpio_enable_usart3(void) +{ + gpio_select_periph_B(GPIO_PIN_PB18, 0); + gpio_select_periph_B(GPIO_PIN_PB19, 0); +} diff --git a/cpu/at32ap/at32ap7000/hebi.c b/cpu/at32ap/at32ap7000/hebi.c deleted file mode 100644 index 3b32adf1ea9..00000000000 --- a/cpu/at32ap/at32ap7000/hebi.c +++ /dev/null @@ -1,38 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#include - -#include - -#include -#include -#include - -void cpu_enable_sdram(void) -{ - const struct device *hmatrix; - - hmatrix = get_device(DEVICE_HMATRIX); - - /* Set the SDRAM_ENABLE bit in the HEBI SFR */ - hmatrix2_writel(hmatrix, SFR4, 1 << 1); -} diff --git a/cpu/at32ap/cpu.c b/cpu/at32ap/cpu.c index 37e3ea040be..311466b7814 100644 --- a/cpu/at32ap/cpu.c +++ b/cpu/at32ap/cpu.c @@ -26,33 +26,79 @@ #include #include +#include #include -#include #include "hsmc3.h" +#include "sm.h" + +/* Sanity checks */ +#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB) \ + || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA) \ + || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB) +# error Constraint fCPU >= fHSB >= fPB{A,B} violated +#endif +#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1)) +# error Invalid PLL multiplier and/or divider +#endif DECLARE_GLOBAL_DATA_PTR; +static void pm_init(void) +{ + uint32_t cksel; + +#ifdef CONFIG_PLL + /* Initialize the PLL */ + sm_writel(PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES) + | SM_BF(PLLMUL, CFG_PLL0_MUL - 1) + | SM_BF(PLLDIV, CFG_PLL0_DIV - 1) + | SM_BF(PLLOPT, CFG_PLL0_OPT) + | SM_BF(PLLOSC, 0) + | SM_BIT(PLLEN))); + + /* Wait for lock */ + while (!(sm_readl(PM_ISR) & SM_BIT(LOCK0))) ; +#endif + + /* Set up clocks for the CPU and all peripheral buses */ + cksel = 0; + if (CFG_CLKDIV_CPU) + cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1); + if (CFG_CLKDIV_HSB) + cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1); + if (CFG_CLKDIV_PBA) + cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1); + if (CFG_CLKDIV_PBB) + cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1); + sm_writel(PM_CKSEL, cksel); + + gd->cpu_hz = get_cpu_clk_rate(); + +#ifdef CONFIG_PLL + /* Use PLL0 as main clock */ + sm_writel(PM_MCCTRL, SM_BIT(PLLSEL)); +#endif +} + int cpu_init(void) { - const struct device *hebi; extern void _evba(void); char *p; gd->cpu_hz = CFG_OSC0_HZ; - /* fff03400: 00010001 04030402 00050005 10011103 */ - hebi = get_device(DEVICE_HEBI); - hsmc3_writel(hebi, MODE0, 0x00031103); - hsmc3_writel(hebi, CYCLE0, 0x000c000d); - hsmc3_writel(hebi, PULSE0, 0x0b0a0906); - hsmc3_writel(hebi, SETUP0, 0x00010002); + /* TODO: Move somewhere else, but needs to be run before we + * increase the clock frequency. */ + hsmc3_writel(MODE0, 0x00031103); + hsmc3_writel(CYCLE0, 0x000c000d); + hsmc3_writel(PULSE0, 0x0b0a0906); + hsmc3_writel(SETUP0, 0x00010002); pm_init(); sysreg_write(EVBA, (unsigned long)&_evba); asm volatile("csrf %0" : : "i"(SYSREG_EM_OFFSET)); - gd->console_uart = get_device(CFG_CONSOLE_UART_DEV); /* Lock everything that mess with the flash in the icache */ for (p = __flashprog_start; p <= (__flashprog_end + CFG_ICACHE_LINESZ); diff --git a/cpu/at32ap/device.c b/cpu/at32ap/device.c deleted file mode 100644 index 89914b6b56b..00000000000 --- a/cpu/at32ap/device.c +++ /dev/null @@ -1,126 +0,0 @@ -/* - * Copyright (C) 2006 Atmel Corporation - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#include - -#include - -#include "sm.h" - -struct device_state { - int refcount; -}; - -static struct device_state device_state[NR_DEVICES]; - -static int claim_resource(const struct resource *res) -{ - int ret = 0; - - switch (res->type) { - case RESOURCE_GPIO: - ret = gpio_set_func(res->u.gpio.gpio_dev, - res->u.gpio.start, - res->u.gpio.nr_pins, - res->u.gpio.func); - break; - case RESOURCE_CLOCK: - ret = pm_enable_clock(res->u.clock.id, res->u.clock.index); - break; - } - - return ret; -} - -static void free_resource(const struct resource *res) -{ - switch (res->type) { - case RESOURCE_GPIO: - gpio_free(res->u.gpio.gpio_dev, res->u.gpio.start, - res->u.gpio.nr_pins); - break; - case RESOURCE_CLOCK: - pm_disable_clock(res->u.clock.id, res->u.clock.index); - break; - } -} - -static int init_dev(const struct device *dev) -{ - unsigned int i; - int ret = 0; - - for (i = 0; i < dev->nr_resources; i++) { - ret = claim_resource(&dev->resource[i]); - if (ret) - goto cleanup; - } - - return 0; - -cleanup: - while (i--) - free_resource(&dev->resource[i]); - - return ret; -} - -const struct device *get_device(enum device_id devid) -{ - struct device_state *devstate; - const struct device *dev; - unsigned long flags; - int initialized = 0; - int ret = 0; - - devstate = &device_state[devid]; - dev = &chip_device[devid]; - - flags = disable_interrupts(); - if (devstate->refcount++) - initialized = 1; - if (flags) - enable_interrupts(); - - if (!initialized) - ret = init_dev(dev); - - return ret ? NULL : dev; -} - -void put_device(const struct device *dev) -{ - struct device_state *devstate; - unsigned long devid, flags; - - devid = (unsigned long)(dev - chip_device) / sizeof(struct device); - devstate = &device_state[devid]; - - flags = disable_interrupts(); - devstate--; - if (!devstate) { - unsigned int i; - for (i = 0; i < dev->nr_resources; i++) - free_resource(&dev->resource[i]); - } - if (flags) - enable_interrupts(); -} diff --git a/cpu/at32ap/hsdramc.c b/cpu/at32ap/hsdramc.c index f36da354528..a936e03166c 100644 --- a/cpu/at32ap/hsdramc.c +++ b/cpu/at32ap/hsdramc.c @@ -25,17 +25,11 @@ #include #include -#include +#include +#include #include "hsdramc1.h" -struct hsdramc { - const struct device *hebi; - void *regs; -}; - -static struct hsdramc hsdramc; - unsigned long sdram_init(const struct sdram_info *info) { unsigned long *sdram = (unsigned long *)uncached(info->phys_addr); @@ -44,16 +38,6 @@ unsigned long sdram_init(const struct sdram_info *info) unsigned long bus_hz; unsigned int i; - hsdramc.hebi = get_device(DEVICE_HEBI); - if (!hsdramc.hebi) - return 0; - - /* FIXME: Both of these lines are complete hacks */ - hsdramc.regs = hsdramc.hebi->regs + 0x400; - bus_hz = pm_get_clock_freq(hsdramc.hebi->resource[0].u.clock.id); - - cpu_enable_sdram(); - tmp = (HSDRAMC1_BF(NC, info->col_bits - 8) | HSDRAMC1_BF(NR, info->row_bits - 11) | HSDRAMC1_BF(NB, info->bank_bits - 1) @@ -74,7 +58,7 @@ unsigned long sdram_init(const struct sdram_info *info) + info->bank_bits + 2); #endif - hsdramc1_writel(&hsdramc, CR, tmp); + hsdramc1_writel(CR, tmp); /* * Initialization sequence for SDRAM, from the data sheet: @@ -87,15 +71,15 @@ unsigned long sdram_init(const struct sdram_info *info) /* * 2. A Precharge All command is issued to the SDRAM */ - hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_BANKS_PRECHARGE); - hsdramc1_readl(&hsdramc, MR); + hsdramc1_writel(MR, HSDRAMC1_MODE_BANKS_PRECHARGE); + hsdramc1_readl(MR); writel(0, sdram); /* * 3. Eight auto-refresh (CBR) cycles are provided */ - hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_AUTO_REFRESH); - hsdramc1_readl(&hsdramc, MR); + hsdramc1_writel(MR, HSDRAMC1_MODE_AUTO_REFRESH); + hsdramc1_readl(MR); for (i = 0; i < 8; i++) writel(0, sdram); @@ -106,8 +90,8 @@ unsigned long sdram_init(const struct sdram_info *info) * * CAS from info struct, burst length 1, serial burst type */ - hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_LOAD_MODE); - hsdramc1_readl(&hsdramc, MR); + hsdramc1_writel(MR, HSDRAMC1_MODE_LOAD_MODE); + hsdramc1_readl(MR); writel(0, sdram + (info->cas << 4)); /* @@ -117,9 +101,9 @@ unsigned long sdram_init(const struct sdram_info *info) * From the timing diagram, it looks like tMRD is 3 * cycles...try a dummy read from the peripheral bus. */ - hsdramc1_readl(&hsdramc, MR); - hsdramc1_writel(&hsdramc, MR, HSDRAMC1_MODE_NORMAL); - hsdramc1_readl(&hsdramc, MR); + hsdramc1_readl(MR); + hsdramc1_writel(MR, HSDRAMC1_MODE_NORMAL); + hsdramc1_readl(MR); writel(0, sdram); /* @@ -128,7 +112,8 @@ unsigned long sdram_init(const struct sdram_info *info) * * 15.6 us is a typical value for a burst of length one */ - hsdramc1_writel(&hsdramc, TR, (156 * (bus_hz / 1000)) / 10000); + bus_hz = get_sdram_clk_rate(); + hsdramc1_writel(TR, (156 * (bus_hz / 1000)) / 10000); printf("SDRAM: %u MB at address 0x%08lx\n", sdram_size >> 20, info->phys_addr); diff --git a/cpu/at32ap/hsdramc1.h b/cpu/at32ap/hsdramc1.h index ce229bca1fb..305d2cb5d39 100644 --- a/cpu/at32ap/hsdramc1.h +++ b/cpu/at32ap/hsdramc1.h @@ -135,9 +135,9 @@ | HSDRAMC1_BF(name,value)) /* Register access macros */ -#define hsdramc1_readl(port,reg) \ - readl((port)->regs + HSDRAMC1_##reg) -#define hsdramc1_writel(port,reg,value) \ - writel((value), (port)->regs + HSDRAMC1_##reg) +#define hsdramc1_readl(reg) \ + readl((void *)HSDRAMC_BASE + HSDRAMC1_##reg) +#define hsdramc1_writel(reg,value) \ + writel((value), (void *)HSDRAMC_BASE + HSDRAMC1_##reg) #endif /* __ASM_AVR32_HSDRAMC1_H__ */ diff --git a/cpu/at32ap/hsmc3.h b/cpu/at32ap/hsmc3.h index ec78cee7147..ca533b922ed 100644 --- a/cpu/at32ap/hsmc3.h +++ b/cpu/at32ap/hsmc3.h @@ -118,9 +118,9 @@ | HSMC3_BF(name,value)) /* Register access macros */ -#define hsmc3_readl(port,reg) \ - readl((port)->regs + HSMC3_##reg) -#define hsmc3_writel(port,reg,value) \ - writel((value), (port)->regs + HSMC3_##reg) +#define hsmc3_readl(reg) \ + readl((void *)HSMC_BASE + HSMC3_##reg) +#define hsmc3_writel(reg,value) \ + writel((value), (void *)HSMC_BASE + HSMC3_##reg) #endif /* __CPU_AT32AP_HSMC3_H__ */ diff --git a/cpu/at32ap/interrupts.c b/cpu/at32ap/interrupts.c index d720cfa942b..85420a4248a 100644 --- a/cpu/at32ap/interrupts.c +++ b/cpu/at32ap/interrupts.c @@ -27,7 +27,7 @@ #include #include -#include +#include #define HANDLER_MASK 0x00ffffff #define INTLEV_SHIFT 30 @@ -44,8 +44,6 @@ volatile unsigned long timer_overflow; */ static unsigned long tb_factor; -static const struct device *intc_dev; - unsigned long get_tbclk(void) { return gd->cpu_hz; @@ -126,7 +124,7 @@ static int set_interrupt_handler(unsigned int nr, void (*handler)(void), intpr = (handler_addr & HANDLER_MASK); intpr |= (priority & INTLEV_MASK) << INTLEV_SHIFT; - writel(intpr, intc_dev->regs + 4 * nr); + writel(intpr, (void *)INTC_BASE + 4 * nr); return 0; } @@ -143,10 +141,7 @@ void timer_init(void) do_div(tmp, gd->cpu_hz); tb_factor = (u32)tmp; - intc_dev = get_device(DEVICE_INTC); - - if (!intc_dev - || set_interrupt_handler(0, &timer_interrupt_handler, 3)) + if (set_interrupt_handler(0, &timer_interrupt_handler, 3)) return; /* For all practical purposes, this gives us an overflow interrupt */ diff --git a/cpu/at32ap/pio.c b/cpu/at32ap/pio.c index 8b6c3a35df5..9ba0b8ea8b2 100644 --- a/cpu/at32ap/pio.c +++ b/cpu/at32ap/pio.c @@ -21,74 +21,40 @@ */ #include -#include #include -#include +#include +#include #include "pio2.h" -struct pio_state { - const struct device *dev; - u32 alloc_mask; -}; - -static struct pio_state pio_state[CFG_NR_PIOS]; - -int gpio_set_func(enum device_id gpio_devid, unsigned int start, - unsigned int nr_pins, enum gpio_func func) +void gpio_select_periph_A(unsigned int pin, int use_pullup) { - const struct device *gpio; - struct pio_state *state; - u32 mask; - - state = &pio_state[gpio_devid - DEVICE_PIOA]; - - gpio = get_device(gpio_devid); - if (!gpio) - return -EBUSY; - - state->dev = gpio; - mask = ((1 << nr_pins) - 1) << start; - - if (mask & state->alloc_mask) { - put_device(gpio); - return -EBUSY; - } - state->alloc_mask |= mask; - - switch (func) { - case GPIO_FUNC_GPIO: - /* TODO */ - return -EINVAL; - case GPIO_FUNC_A: - pio2_writel(gpio, ASR, mask); - pio2_writel(gpio, PDR, mask); - pio2_writel(gpio, PUDR, mask); - break; - case GPIO_FUNC_B: - pio2_writel(gpio, BSR, mask); - pio2_writel(gpio, PDR, mask); - pio2_writel(gpio, PUDR, mask); - break; - } - - return 0; + void *base = gpio_pin_to_addr(pin); + uint32_t mask = 1 << (pin & 0x1f); + + if (!base) + panic("Invalid GPIO pin %u\n", pin); + + pio2_writel(base, ASR, mask); + pio2_writel(base, PDR, mask); + if (use_pullup) + pio2_writel(base, PUER, mask); + else + pio2_writel(base, PUDR, mask); } -void gpio_free(enum device_id gpio_devid, unsigned int start, - unsigned int nr_pins) +void gpio_select_periph_B(unsigned int pin, int use_pullup) { - const struct device *gpio; - struct pio_state *state; - u32 mask; - - state = &pio_state[gpio_devid - DEVICE_PIOA]; - gpio = state->dev; - mask = ((1 << nr_pins) - 1) << start; - - pio2_writel(gpio, ODR, mask); - pio2_writel(gpio, PER, mask); - - state->alloc_mask &= ~mask; - put_device(gpio); + void *base = gpio_pin_to_addr(pin); + uint32_t mask = 1 << (pin & 0x1f); + + if (!base) + panic("Invalid GPIO pin %u\n", pin); + + pio2_writel(base, BSR, mask); + pio2_writel(base, PDR, mask); + if (use_pullup) + pio2_writel(base, PUER, mask); + else + pio2_writel(base, PUDR, mask); } diff --git a/cpu/at32ap/pio2.h b/cpu/at32ap/pio2.h index 6b79de3c72b..9719ea8c433 100644 --- a/cpu/at32ap/pio2.h +++ b/cpu/at32ap/pio2.h @@ -36,9 +36,9 @@ #define PIO2_OWSR 0x00a8 /* Register access macros */ -#define pio2_readl(port,reg) \ - readl((port)->regs + PIO2_##reg) -#define pio2_writel(port,reg,value) \ - writel((value), (port)->regs + PIO2_##reg) +#define pio2_readl(base,reg) \ + readl((void *)base + PIO2_##reg) +#define pio2_writel(base,reg,value) \ + writel((value), (void *)base + PIO2_##reg) #endif /* __CPU_AT32AP_PIO2_H__ */ diff --git a/cpu/at32ap/pm.c b/cpu/at32ap/pm.c index 01ac325ee8f..c78d547f85e 100644 --- a/cpu/at32ap/pm.c +++ b/cpu/at32ap/pm.c @@ -26,138 +26,17 @@ #include #include -#include #include "sm.h" -/* Sanity checks */ -#if (CFG_CLKDIV_CPU > CFG_CLKDIV_HSB) \ - || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBA) \ - || (CFG_CLKDIV_HSB > CFG_CLKDIV_PBB) -# error Constraint fCPU >= fHSB >= fPB{A,B} violated -#endif -#if defined(CONFIG_PLL) && ((CFG_PLL0_MUL < 1) || (CFG_PLL0_DIV < 1)) -# error Invalid PLL multiplier and/or divider -#endif - -DECLARE_GLOBAL_DATA_PTR; - -struct clock_domain_state { - const struct device *bridge; - unsigned long freq; - u32 mask; -}; -static struct clock_domain_state ckd_state[NR_CLOCK_DOMAINS]; - -int pm_enable_clock(enum clock_domain_id id, unsigned int index) -{ - const struct clock_domain *ckd = &chip_clock[id]; - struct clock_domain_state *state = &ckd_state[id]; - - if (ckd->bridge != NO_DEVICE) { - state->bridge = get_device(ckd->bridge); - if (!state->bridge) - return -EBUSY; - } - - state->mask |= 1 << index; - if (gd->sm) - writel(state->mask, gd->sm->regs + ckd->reg); - - return 0; -} - -void pm_disable_clock(enum clock_domain_id id, unsigned int index) -{ - const struct clock_domain *ckd = &chip_clock[id]; - struct clock_domain_state *state = &ckd_state[id]; - - state->mask &= ~(1 << index); - if (gd->sm) - writel(state->mask, gd->sm->regs + ckd->reg); - - if (ckd->bridge) - put_device(state->bridge); -} - -unsigned long pm_get_clock_freq(enum clock_domain_id domain) -{ - return ckd_state[domain].freq; -} - -void pm_init(void) -{ - uint32_t cksel = 0; - unsigned long main_clock; - - /* Make sure we don't disable any device we're already using */ - get_device(DEVICE_HRAMC); - get_device(DEVICE_HEBI); - - /* Enable the PICO as well */ - ckd_state[CLOCK_CPU].mask |= 1; - - gd->sm = get_device(DEVICE_SM); - if (!gd->sm) - panic("Unable to claim system manager device!\n"); - - /* Disable any devices that haven't been explicitly claimed */ - sm_writel(gd->sm, PM_PBB_MASK, ckd_state[CLOCK_PBB].mask); - sm_writel(gd->sm, PM_PBA_MASK, ckd_state[CLOCK_PBA].mask); - sm_writel(gd->sm, PM_HSB_MASK, ckd_state[CLOCK_HSB].mask); - sm_writel(gd->sm, PM_CPU_MASK, ckd_state[CLOCK_CPU].mask); #ifdef CONFIG_PLL - /* Initialize the PLL */ - main_clock = (CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL; - - sm_writel(gd->sm, PM_PLL0, (SM_BF(PLLCOUNT, CFG_PLL0_SUPPRESS_CYCLES) - | SM_BF(PLLMUL, CFG_PLL0_MUL - 1) - | SM_BF(PLLDIV, CFG_PLL0_DIV - 1) - | SM_BF(PLLOPT, CFG_PLL0_OPT) - | SM_BF(PLLOSC, 0) - | SM_BIT(PLLEN))); - - /* Wait for lock */ - while (!(sm_readl(gd->sm, PM_ISR) & SM_BIT(LOCK0))) ; +#define MAIN_CLK_RATE ((CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL) #else - main_clock = CFG_OSC0_HZ; +#define MAIN_CLK_RATE (CFG_OSC0_HZ) #endif - /* Set up clocks for the CPU and all peripheral buses */ - if (CFG_CLKDIV_CPU) { - cksel |= SM_BIT(CPUDIV) | SM_BF(CPUSEL, CFG_CLKDIV_CPU - 1); - ckd_state[CLOCK_CPU].freq = main_clock / (1 << CFG_CLKDIV_CPU); - } else { - ckd_state[CLOCK_CPU].freq = main_clock; - } - if (CFG_CLKDIV_HSB) { - cksel |= SM_BIT(HSBDIV) | SM_BF(HSBSEL, CFG_CLKDIV_HSB - 1); - ckd_state[CLOCK_HSB].freq = main_clock / (1 << CFG_CLKDIV_HSB); - } else { - ckd_state[CLOCK_HSB].freq = main_clock; - } - if (CFG_CLKDIV_PBA) { - cksel |= SM_BIT(PBADIV) | SM_BF(PBASEL, CFG_CLKDIV_PBA - 1); - ckd_state[CLOCK_PBA].freq = main_clock / (1 << CFG_CLKDIV_PBA); - } else { - ckd_state[CLOCK_PBA].freq = main_clock; - } - if (CFG_CLKDIV_PBB) { - cksel |= SM_BIT(PBBDIV) | SM_BF(PBBSEL, CFG_CLKDIV_PBB - 1); - ckd_state[CLOCK_PBB].freq = main_clock / (1 << CFG_CLKDIV_PBB); - } else { - ckd_state[CLOCK_PBB].freq = main_clock; - } - sm_writel(gd->sm, PM_CKSEL, cksel); - - /* CFG_HZ currently depends on cpu_hz */ - gd->cpu_hz = ckd_state[CLOCK_CPU].freq; +DECLARE_GLOBAL_DATA_PTR; -#ifdef CONFIG_PLL - /* Use PLL0 as main clock */ - sm_writel(gd->sm, PM_MCCTRL, SM_BIT(PLLSEL)); -#endif -} #endif /* CFG_POWER_MANAGER */ diff --git a/cpu/at32ap/sm.h b/cpu/at32ap/sm.h index ce81ef0a463..6492c8e81d2 100644 --- a/cpu/at32ap/sm.h +++ b/cpu/at32ap/sm.h @@ -196,9 +196,9 @@ | SM_BF(name,value)) /* Register access macros */ -#define sm_readl(port,reg) \ - readl((port)->regs + SM_##reg) -#define sm_writel(port,reg,value) \ - writel((value), (port)->regs + SM_##reg) +#define sm_readl(reg) \ + readl((void *)SM_BASE + SM_##reg) +#define sm_writel(reg,value) \ + writel((value), (void *)SM_BASE + SM_##reg) #endif /* __CPU_AT32AP_SM_H__ */ diff --git a/drivers/atmel_usart.c b/drivers/atmel_usart.c index 41c37683d78..f35b99730f7 100644 --- a/drivers/atmel_usart.c +++ b/drivers/atmel_usart.c @@ -19,7 +19,22 @@ #ifdef CONFIG_ATMEL_USART #include -#include +#include +#include + +#if defined(CONFIG_USART0) +# define USART_ID 0 +# define USART_BASE USART0_BASE +#elif defined(CONFIG_USART1) +# define USART_ID 1 +# define USART_BASE USART1_BASE +#elif defined(CONFIG_USART2) +# define USART_ID 2 +# define USART_BASE USART2_BASE +#elif defined(CONFIG_USART3) +# define USART_ID 3 +# define USART_BASE USART3_BASE +#endif #include "atmel_usart.h" @@ -35,26 +50,23 @@ void serial_setbrg(void) * Baud Rate = -------------- * 16 * CD */ - usart_hz = pm_get_clock_freq(gd->console_uart->resource[0].u.clock.id); + usart_hz = get_usart_clk_rate(USART_ID); divisor = (usart_hz / 16 + gd->baudrate / 2) / gd->baudrate; - usart3_writel(gd->console_uart, BRGR, USART3_BF(CD, divisor)); + usart3_writel(BRGR, USART3_BF(CD, divisor)); } int serial_init(void) { - usart3_writel(gd->console_uart, CR, - USART3_BIT(RSTRX) | USART3_BIT(RSTTX)); + usart3_writel(CR, USART3_BIT(RSTRX) | USART3_BIT(RSTTX)); serial_setbrg(); - usart3_writel(gd->console_uart, CR, - USART3_BIT(RXEN) | USART3_BIT(TXEN)); - usart3_writel(gd->console_uart, MR, - USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL) - | USART3_BF(USCLKS, USART3_USCLKS_MCK) - | USART3_BF(CHRL, USART3_CHRL_8) - | USART3_BF(PAR, USART3_PAR_NONE) - | USART3_BF(NBSTOP, USART3_NBSTOP_1)); + usart3_writel(CR, USART3_BIT(RXEN) | USART3_BIT(TXEN)); + usart3_writel(MR, (USART3_BF(USART_MODE, USART3_USART_MODE_NORMAL) + | USART3_BF(USCLKS, USART3_USCLKS_MCK) + | USART3_BF(CHRL, USART3_CHRL_8) + | USART3_BF(PAR, USART3_PAR_NONE) + | USART3_BF(NBSTOP, USART3_NBSTOP_1))); return 0; } @@ -64,8 +76,8 @@ void serial_putc(char c) if (c == '\n') serial_putc('\r'); - while (!(usart3_readl(gd->console_uart, CSR) & USART3_BIT(TXRDY))) ; - usart3_writel(gd->console_uart, THR, c); + while (!(usart3_readl(CSR) & USART3_BIT(TXRDY))) ; + usart3_writel(THR, c); } void serial_puts(const char *s) @@ -76,13 +88,13 @@ void serial_puts(const char *s) int serial_getc(void) { - while (!(usart3_readl(gd->console_uart, CSR) & USART3_BIT(RXRDY))) ; - return usart3_readl(gd->console_uart, RHR); + while (!(usart3_readl(CSR) & USART3_BIT(RXRDY))) ; + return usart3_readl(RHR); } int serial_tstc(void) { - return (usart3_readl(gd->console_uart, CSR) & USART3_BIT(RXRDY)) != 0; + return (usart3_readl(CSR) & USART3_BIT(RXRDY)) != 0; } #endif /* CONFIG_ATMEL_USART */ diff --git a/drivers/atmel_usart.h b/drivers/atmel_usart.h index fad90a8116e..af3773a99f2 100644 --- a/drivers/atmel_usart.h +++ b/drivers/atmel_usart.h @@ -306,9 +306,9 @@ | USART3_BF(name,value)) /* Register access macros */ -#define usart3_readl(port,reg) \ - readl((port)->regs + USART3_##reg) -#define usart3_writel(port,reg,value) \ - writel((value), (port)->regs + USART3_##reg) +#define usart3_readl(reg) \ + readl((void *)USART_BASE + USART3_##reg) +#define usart3_writel(reg,value) \ + writel((value), (void *)USART_BASE + USART3_##reg) #endif /* __DRIVERS_ATMEL_USART_H__ */ diff --git a/include/asm-avr32/arch-at32ap7000/clk.h b/include/asm-avr32/arch-at32ap7000/clk.h new file mode 100644 index 00000000000..4a25b17ad49 --- /dev/null +++ b/include/asm-avr32/arch-at32ap7000/clk.h @@ -0,0 +1,58 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_ARCH_CLK_H__ +#define __ASM_AVR32_ARCH_CLK_H__ + +#ifdef CONFIG_PLL +#define MAIN_CLK_RATE ((CFG_OSC0_HZ / CFG_PLL0_DIV) * CFG_PLL0_MUL) +#else +#define MAIN_CLK_RATE (CFG_OSC0_HZ) +#endif + +static inline unsigned long get_cpu_clk_rate(void) +{ + return MAIN_CLK_RATE >> CFG_CLKDIV_CPU; +} +static inline unsigned long get_hsb_clk_rate(void) +{ + return MAIN_CLK_RATE >> CFG_CLKDIV_HSB; +} +static inline unsigned long get_pba_clk_rate(void) +{ + return MAIN_CLK_RATE >> CFG_CLKDIV_PBA; +} +static inline unsigned long get_pbb_clk_rate(void) +{ + return MAIN_CLK_RATE >> CFG_CLKDIV_PBB; +} + +/* Accessors for specific devices. More will be added as needed. */ +static inline unsigned long get_sdram_clk_rate(void) +{ + return get_hsb_clk_rate(); +} +static inline unsigned long get_usart_clk_rate(unsigned int dev_id) +{ + return get_pba_clk_rate(); +} + +#endif /* __ASM_AVR32_ARCH_CLK_H__ */ diff --git a/include/asm-avr32/arch-at32ap7000/gpio.h b/include/asm-avr32/arch-at32ap7000/gpio.h new file mode 100644 index 00000000000..adec2083f2a --- /dev/null +++ b/include/asm-avr32/arch-at32ap7000/gpio.h @@ -0,0 +1,210 @@ +/* + * Copyright (C) 2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __ASM_AVR32_ARCH_GPIO_H__ +#define __ASM_AVR32_ARCH_GPIO_H__ + +#include + +#define NR_GPIO_CONTROLLERS 5 + +/* + * Pin numbers identifying specific GPIO pins on the chip. + */ +#define GPIO_PIOA_BASE (0) +#define GPIO_PIN_PA0 (GPIO_PIOA_BASE + 0) +#define GPIO_PIN_PA1 (GPIO_PIOA_BASE + 1) +#define GPIO_PIN_PA2 (GPIO_PIOA_BASE + 2) +#define GPIO_PIN_PA3 (GPIO_PIOA_BASE + 3) +#define GPIO_PIN_PA4 (GPIO_PIOA_BASE + 4) +#define GPIO_PIN_PA5 (GPIO_PIOA_BASE + 5) +#define GPIO_PIN_PA6 (GPIO_PIOA_BASE + 6) +#define GPIO_PIN_PA7 (GPIO_PIOA_BASE + 7) +#define GPIO_PIN_PA8 (GPIO_PIOA_BASE + 8) +#define GPIO_PIN_PA9 (GPIO_PIOA_BASE + 9) +#define GPIO_PIN_PA10 (GPIO_PIOA_BASE + 10) +#define GPIO_PIN_PA11 (GPIO_PIOA_BASE + 11) +#define GPIO_PIN_PA12 (GPIO_PIOA_BASE + 12) +#define GPIO_PIN_PA13 (GPIO_PIOA_BASE + 13) +#define GPIO_PIN_PA14 (GPIO_PIOA_BASE + 14) +#define GPIO_PIN_PA15 (GPIO_PIOA_BASE + 15) +#define GPIO_PIN_PA16 (GPIO_PIOA_BASE + 16) +#define GPIO_PIN_PA17 (GPIO_PIOA_BASE + 17) +#define GPIO_PIN_PA18 (GPIO_PIOA_BASE + 18) +#define GPIO_PIN_PA19 (GPIO_PIOA_BASE + 19) +#define GPIO_PIN_PA20 (GPIO_PIOA_BASE + 20) +#define GPIO_PIN_PA21 (GPIO_PIOA_BASE + 21) +#define GPIO_PIN_PA22 (GPIO_PIOA_BASE + 22) +#define GPIO_PIN_PA23 (GPIO_PIOA_BASE + 23) +#define GPIO_PIN_PA24 (GPIO_PIOA_BASE + 24) +#define GPIO_PIN_PA25 (GPIO_PIOA_BASE + 25) +#define GPIO_PIN_PA26 (GPIO_PIOA_BASE + 26) +#define GPIO_PIN_PA27 (GPIO_PIOA_BASE + 27) +#define GPIO_PIN_PA28 (GPIO_PIOA_BASE + 28) +#define GPIO_PIN_PA29 (GPIO_PIOA_BASE + 29) +#define GPIO_PIN_PA30 (GPIO_PIOA_BASE + 30) +#define GPIO_PIN_PA31 (GPIO_PIOA_BASE + 31) + +#define GPIO_PIOB_BASE (GPIO_PIOA_BASE + 32) +#define GPIO_PIN_PB0 (GPIO_PIOB_BASE + 0) +#define GPIO_PIN_PB1 (GPIO_PIOB_BASE + 1) +#define GPIO_PIN_PB2 (GPIO_PIOB_BASE + 2) +#define GPIO_PIN_PB3 (GPIO_PIOB_BASE + 3) +#define GPIO_PIN_PB4 (GPIO_PIOB_BASE + 4) +#define GPIO_PIN_PB5 (GPIO_PIOB_BASE + 5) +#define GPIO_PIN_PB6 (GPIO_PIOB_BASE + 6) +#define GPIO_PIN_PB7 (GPIO_PIOB_BASE + 7) +#define GPIO_PIN_PB8 (GPIO_PIOB_BASE + 8) +#define GPIO_PIN_PB9 (GPIO_PIOB_BASE + 9) +#define GPIO_PIN_PB10 (GPIO_PIOB_BASE + 10) +#define GPIO_PIN_PB11 (GPIO_PIOB_BASE + 11) +#define GPIO_PIN_PB12 (GPIO_PIOB_BASE + 12) +#define GPIO_PIN_PB13 (GPIO_PIOB_BASE + 13) +#define GPIO_PIN_PB14 (GPIO_PIOB_BASE + 14) +#define GPIO_PIN_PB15 (GPIO_PIOB_BASE + 15) +#define GPIO_PIN_PB16 (GPIO_PIOB_BASE + 16) +#define GPIO_PIN_PB17 (GPIO_PIOB_BASE + 17) +#define GPIO_PIN_PB18 (GPIO_PIOB_BASE + 18) +#define GPIO_PIN_PB19 (GPIO_PIOB_BASE + 19) +#define GPIO_PIN_PB20 (GPIO_PIOB_BASE + 20) +#define GPIO_PIN_PB21 (GPIO_PIOB_BASE + 21) +#define GPIO_PIN_PB22 (GPIO_PIOB_BASE + 22) +#define GPIO_PIN_PB23 (GPIO_PIOB_BASE + 23) +#define GPIO_PIN_PB24 (GPIO_PIOB_BASE + 24) +#define GPIO_PIN_PB25 (GPIO_PIOB_BASE + 25) +#define GPIO_PIN_PB26 (GPIO_PIOB_BASE + 26) +#define GPIO_PIN_PB27 (GPIO_PIOB_BASE + 27) +#define GPIO_PIN_PB28 (GPIO_PIOB_BASE + 28) +#define GPIO_PIN_PB29 (GPIO_PIOB_BASE + 29) +#define GPIO_PIN_PB30 (GPIO_PIOB_BASE + 30) + +#define GPIO_PIOC_BASE (GPIO_PIOB_BASE + 32) +#define GPIO_PIN_PC0 (GPIO_PIOC_BASE + 0) +#define GPIO_PIN_PC1 (GPIO_PIOC_BASE + 1) +#define GPIO_PIN_PC2 (GPIO_PIOC_BASE + 2) +#define GPIO_PIN_PC3 (GPIO_PIOC_BASE + 3) +#define GPIO_PIN_PC4 (GPIO_PIOC_BASE + 4) +#define GPIO_PIN_PC5 (GPIO_PIOC_BASE + 5) +#define GPIO_PIN_PC6 (GPIO_PIOC_BASE + 6) +#define GPIO_PIN_PC7 (GPIO_PIOC_BASE + 7) +#define GPIO_PIN_PC8 (GPIO_PIOC_BASE + 8) +#define GPIO_PIN_PC9 (GPIO_PIOC_BASE + 9) +#define GPIO_PIN_PC10 (GPIO_PIOC_BASE + 10) +#define GPIO_PIN_PC11 (GPIO_PIOC_BASE + 11) +#define GPIO_PIN_PC12 (GPIO_PIOC_BASE + 12) +#define GPIO_PIN_PC13 (GPIO_PIOC_BASE + 13) +#define GPIO_PIN_PC14 (GPIO_PIOC_BASE + 14) +#define GPIO_PIN_PC15 (GPIO_PIOC_BASE + 15) +#define GPIO_PIN_PC16 (GPIO_PIOC_BASE + 16) +#define GPIO_PIN_PC17 (GPIO_PIOC_BASE + 17) +#define GPIO_PIN_PC18 (GPIO_PIOC_BASE + 18) +#define GPIO_PIN_PC19 (GPIO_PIOC_BASE + 19) +#define GPIO_PIN_PC20 (GPIO_PIOC_BASE + 20) +#define GPIO_PIN_PC21 (GPIO_PIOC_BASE + 21) +#define GPIO_PIN_PC22 (GPIO_PIOC_BASE + 22) +#define GPIO_PIN_PC23 (GPIO_PIOC_BASE + 23) +#define GPIO_PIN_PC24 (GPIO_PIOC_BASE + 24) +#define GPIO_PIN_PC25 (GPIO_PIOC_BASE + 25) +#define GPIO_PIN_PC26 (GPIO_PIOC_BASE + 26) +#define GPIO_PIN_PC27 (GPIO_PIOC_BASE + 27) +#define GPIO_PIN_PC28 (GPIO_PIOC_BASE + 28) +#define GPIO_PIN_PC29 (GPIO_PIOC_BASE + 29) +#define GPIO_PIN_PC30 (GPIO_PIOC_BASE + 30) +#define GPIO_PIN_PC31 (GPIO_PIOC_BASE + 31) + +#define GPIO_PIOD_BASE (GPIO_PIOC_BASE + 32) +#define GPIO_PIN_PD0 (GPIO_PIOD_BASE + 0) +#define GPIO_PIN_PD1 (GPIO_PIOD_BASE + 1) +#define GPIO_PIN_PD2 (GPIO_PIOD_BASE + 2) +#define GPIO_PIN_PD3 (GPIO_PIOD_BASE + 3) +#define GPIO_PIN_PD4 (GPIO_PIOD_BASE + 4) +#define GPIO_PIN_PD5 (GPIO_PIOD_BASE + 5) +#define GPIO_PIN_PD6 (GPIO_PIOD_BASE + 6) +#define GPIO_PIN_PD7 (GPIO_PIOD_BASE + 7) +#define GPIO_PIN_PD8 (GPIO_PIOD_BASE + 8) +#define GPIO_PIN_PD9 (GPIO_PIOD_BASE + 9) +#define GPIO_PIN_PD10 (GPIO_PIOD_BASE + 10) +#define GPIO_PIN_PD11 (GPIO_PIOD_BASE + 11) +#define GPIO_PIN_PD12 (GPIO_PIOD_BASE + 12) +#define GPIO_PIN_PD13 (GPIO_PIOD_BASE + 13) +#define GPIO_PIN_PD14 (GPIO_PIOD_BASE + 14) +#define GPIO_PIN_PD15 (GPIO_PIOD_BASE + 15) +#define GPIO_PIN_PD16 (GPIO_PIOD_BASE + 16) +#define GPIO_PIN_PD17 (GPIO_PIOD_BASE + 17) + +#define GPIO_PIOE_BASE (GPIO_PIOD_BASE + 32) +#define GPIO_PIN_PE0 (GPIO_PIOE_BASE + 0) +#define GPIO_PIN_PE1 (GPIO_PIOE_BASE + 1) +#define GPIO_PIN_PE2 (GPIO_PIOE_BASE + 2) +#define GPIO_PIN_PE3 (GPIO_PIOE_BASE + 3) +#define GPIO_PIN_PE4 (GPIO_PIOE_BASE + 4) +#define GPIO_PIN_PE5 (GPIO_PIOE_BASE + 5) +#define GPIO_PIN_PE6 (GPIO_PIOE_BASE + 6) +#define GPIO_PIN_PE7 (GPIO_PIOE_BASE + 7) +#define GPIO_PIN_PE8 (GPIO_PIOE_BASE + 8) +#define GPIO_PIN_PE9 (GPIO_PIOE_BASE + 9) +#define GPIO_PIN_PE10 (GPIO_PIOE_BASE + 10) +#define GPIO_PIN_PE11 (GPIO_PIOE_BASE + 11) +#define GPIO_PIN_PE12 (GPIO_PIOE_BASE + 12) +#define GPIO_PIN_PE13 (GPIO_PIOE_BASE + 13) +#define GPIO_PIN_PE14 (GPIO_PIOE_BASE + 14) +#define GPIO_PIN_PE15 (GPIO_PIOE_BASE + 15) +#define GPIO_PIN_PE16 (GPIO_PIOE_BASE + 16) +#define GPIO_PIN_PE17 (GPIO_PIOE_BASE + 17) +#define GPIO_PIN_PE18 (GPIO_PIOE_BASE + 18) +#define GPIO_PIN_PE19 (GPIO_PIOE_BASE + 19) +#define GPIO_PIN_PE20 (GPIO_PIOE_BASE + 20) +#define GPIO_PIN_PE21 (GPIO_PIOE_BASE + 21) +#define GPIO_PIN_PE22 (GPIO_PIOE_BASE + 22) +#define GPIO_PIN_PE23 (GPIO_PIOE_BASE + 23) +#define GPIO_PIN_PE24 (GPIO_PIOE_BASE + 24) +#define GPIO_PIN_PE25 (GPIO_PIOE_BASE + 25) +#define GPIO_PIN_PE26 (GPIO_PIOE_BASE + 26) + +static inline void *gpio_pin_to_addr(unsigned int pin) +{ + switch (pin >> 5) { + case 0: + return (void *)PIOA_BASE; + case 1: + return (void *)PIOB_BASE; + case 2: + return (void *)PIOC_BASE; + case 3: + return (void *)PIOD_BASE; + case 4: + return (void *)PIOE_BASE; + default: + return NULL; + } +} + +void gpio_select_periph_A(unsigned int pin, int use_pullup); +void gpio_select_periph_B(unsigned int pin, int use_pullup); + +void gpio_enable_ebi(void); +void gpio_enable_usart0(void); +void gpio_enable_usart1(void); +void gpio_enable_usart2(void); +void gpio_enable_usart3(void); + +#endif /* __ASM_AVR32_ARCH_GPIO_H__ */ + diff --git a/include/asm-avr32/arch-at32ap7000/hmatrix2.h b/include/asm-avr32/arch-at32ap7000/hmatrix2.h index e6df4b7fe33..b0e787a92f9 100644 --- a/include/asm-avr32/arch-at32ap7000/hmatrix2.h +++ b/include/asm-avr32/arch-at32ap7000/hmatrix2.h @@ -224,9 +224,9 @@ | HMATRIX2_BF(name,value)) /* Register access macros */ -#define hmatrix2_readl(port,reg) \ - readl((port)->regs + HMATRIX2_##reg) -#define hmatrix2_writel(port,reg,value) \ - writel((value), (port)->regs + HMATRIX2_##reg) +#define hmatrix2_readl(reg) \ + readl((void *)HMATRIX_BASE + HMATRIX2_##reg) +#define hmatrix2_writel(reg,value) \ + writel((value), (void *)HMATRIX_BASE + HMATRIX2_##reg) #endif /* __ASM_AVR32_HMATRIX2_H__ */ diff --git a/include/asm-avr32/arch-at32ap7000/platform.h b/include/asm-avr32/arch-at32ap7000/platform.h deleted file mode 100644 index 759050116a9..00000000000 --- a/include/asm-avr32/arch-at32ap7000/platform.h +++ /dev/null @@ -1,146 +0,0 @@ -/* - * Copyright (C) 2005-2006 Atmel Corporation - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#ifndef _ASM_AVR32_ARCH_PM_H -#define _ASM_AVR32_ARCH_PM_H - -#include - -enum clock_domain_id { - CLOCK_CPU, - CLOCK_HSB, - CLOCK_PBA, - CLOCK_PBB, - NR_CLOCK_DOMAINS, -}; - -enum resource_type { - RESOURCE_GPIO, - RESOURCE_CLOCK, -}; - -enum gpio_func { - GPIO_FUNC_GPIO, - GPIO_FUNC_A, - GPIO_FUNC_B, -}; - -enum device_id { - DEVICE_HEBI, - DEVICE_PBA_BRIDGE, - DEVICE_PBB_BRIDGE, - DEVICE_HRAMC, - /* GPIO controllers must be kept together */ - DEVICE_PIOA, - DEVICE_PIOB, - DEVICE_PIOC, - DEVICE_PIOD, - DEVICE_PIOE, - DEVICE_SM, - DEVICE_INTC, - DEVICE_HMATRIX, -#if defined(CFG_HPDC) - DEVICE_HPDC, -#endif -#if defined(CFG_MACB0) - DEVICE_MACB0, -#endif -#if defined(CFG_MACB1) - DEVICE_MACB1, -#endif -#if defined(CFG_LCDC) - DEVICE_LCDC, -#endif -#if defined(CFG_USART0) - DEVICE_USART0, -#endif -#if defined(CFG_USART1) - DEVICE_USART1, -#endif -#if defined(CFG_USART2) - DEVICE_USART2, -#endif -#if defined(CFG_USART3) - DEVICE_USART3, -#endif -#if defined(CFG_MMCI) - DEVICE_MMCI, -#endif -#if defined(CFG_DMAC) - DEVICE_DMAC, -#endif - NR_DEVICES, - NO_DEVICE = -1, -}; - -struct resource { - enum resource_type type; - union { - struct { - unsigned long base; - } iomem; - struct { - unsigned char nr_pins; - enum device_id gpio_dev; - enum gpio_func func; - unsigned short start; - } gpio; - struct { - enum clock_domain_id id; - unsigned char index; - } clock; - } u; -}; - -struct device { - void *regs; - unsigned int nr_resources; - const struct resource *resource; -}; - -struct clock_domain { - unsigned short reg; - enum clock_domain_id id; - enum device_id bridge; -}; - -extern const struct device chip_device[NR_DEVICES]; -extern const struct clock_domain chip_clock[NR_CLOCK_DOMAINS]; - -/** - * Set up PIO, clock management and I/O memory for a device. - */ -const struct device *get_device(enum device_id devid); -void put_device(const struct device *dev); - -int gpio_set_func(enum device_id gpio_devid, unsigned int start, - unsigned int nr_pins, enum gpio_func func); -void gpio_free(enum device_id gpio_devid, unsigned int start, - unsigned int nr_pins); - -void pm_init(void); -int pm_enable_clock(enum clock_domain_id id, unsigned int index); -void pm_disable_clock(enum clock_domain_id id, unsigned int index); -unsigned long pm_get_clock_freq(enum clock_domain_id domain); - -void cpu_enable_sdram(void); - -#endif /* _ASM_AVR32_ARCH_PM_H */ diff --git a/include/asm-avr32/global_data.h b/include/asm-avr32/global_data.h index 01d836c6395..3b6769b2748 100644 --- a/include/asm-avr32/global_data.h +++ b/include/asm-avr32/global_data.h @@ -35,8 +35,6 @@ typedef struct global_data { bd_t *bd; unsigned long flags; - const struct device *console_uart; - const struct device *sm; unsigned long baudrate; unsigned long sdram_size; unsigned long have_console; /* serial_init() was called */ diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h index 458ebabeb9a..717f54022c9 100644 --- a/include/configs/atstk1002.h +++ b/include/configs/atstk1002.h @@ -62,9 +62,10 @@ */ #define CFG_PLL0_OPT 0x04 -#define CFG_USART1 1 - -#define CFG_CONSOLE_UART_DEV DEVICE_USART1 +#undef CONFIG_USART0 +#define CONFIG_USART1 1 +#undef CONFIG_USART2 +#undef CONFIG_USART3 /* User serviceable stuff */ #define CONFIG_CMDLINE_TAG 1 diff --git a/lib_avr32/avr32_linux.c b/lib_avr32/avr32_linux.c index d128dfb53f0..6095e2ff214 100644 --- a/lib_avr32/avr32_linux.c +++ b/lib_avr32/avr32_linux.c @@ -27,7 +27,7 @@ #include #include #include -#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -133,7 +133,7 @@ static struct tag *setup_clock_tags(struct tag *params) params->hdr.size = tag_size(tag_clock); params->u.clock.clock_id = ACLOCK_HSB; params->u.clock.clock_flags = 0; - params->u.clock.clock_hz = pm_get_clock_freq(CLOCK_HSB); + params->u.clock.clock_hz = get_hsb_clk_rate(); #endif return tag_next(params); diff --git a/lib_avr32/board.c b/lib_avr32/board.c index c531eef713b..12d0b973b88 100644 --- a/lib_avr32/board.c +++ b/lib_avr32/board.c @@ -131,6 +131,7 @@ void board_init_f(ulong unused) gd = &gd_data; /* Perform initialization sequence */ + board_early_init_f(); cpu_init(); timer_init(); env_init(); -- cgit v1.3.1 From 5c1fe1ffffd1750a7e47e5a2e2cd600c00e4f009 Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Fri, 20 Jan 2006 10:03:34 +0100 Subject: Atmel MACB ethernet driver Driver for the Atmel MACB on-chip ethernet controller. This driver has been tested on the ATSTK1000 board with a AT32AP7000 CPU. It should probably work on AT91SAM926x as well with some minor modifications. Hardware documentation can be found in the AT32AP7000 data sheet, which can be downloaded from http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Signed-off-by: Haavard Skinnemoen --- drivers/Makefile | 2 +- drivers/macb.c | 575 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/macb.h | 269 ++++++++++++++++++++++++++ 3 files changed, 845 insertions(+), 1 deletion(-) create mode 100644 drivers/macb.c create mode 100644 drivers/macb.h (limited to 'drivers') diff --git a/drivers/Makefile b/drivers/Makefile index fffc22a5e1d..2eac7c84855 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -32,7 +32,7 @@ COBJS = 3c589.o 5701rls.o ali512x.o atmel_usart.o \ cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \ e1000.o eepro100.o \ i8042.o inca-ip_sw.o keyboard.o \ - lan91c96.o \ + lan91c96.o macb.o \ natsemi.o ne2000.o netarm_eth.o netconsole.o \ ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \ omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o \ diff --git a/drivers/macb.c b/drivers/macb.c new file mode 100644 index 00000000000..186ab19d35e --- /dev/null +++ b/drivers/macb.c @@ -0,0 +1,575 @@ +/* + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include + +#if defined(CONFIG_MACB) && (CONFIG_COMMANDS & (CFG_CMD_NET | CFG_CMD_MII)) + +/* + * The u-boot networking stack is a little weird. It seems like the + * networking core allocates receive buffers up front without any + * regard to the hardware that's supposed to actually receive those + * packets. + * + * The MACB receives packets into 128-byte receive buffers, so the + * buffers allocated by the core isn't very practical to use. We'll + * allocate our own, but we need one such buffer in case a packet + * wraps around the DMA ring so that we have to copy it. + * + * Therefore, define CFG_RX_ETH_BUFFER to 1 in the board-specific + * configuration header. This way, the core allocates one RX buffer + * and one TX buffer, each of which can hold a ethernet packet of + * maximum size. + * + * For some reason, the networking core unconditionally specifies a + * 32-byte packet "alignment" (which really should be called + * "padding"). MACB shouldn't need that, but we'll refrain from any + * core modifications here... + */ + +#include +#include + +#include +#include +#include +#include + +#include "macb.h" + +#define CFG_MACB_RX_BUFFER_SIZE 4096 +#define CFG_MACB_RX_RING_SIZE (CFG_MACB_RX_BUFFER_SIZE / 128) +#define CFG_MACB_TX_RING_SIZE 16 +#define CFG_MACB_TX_TIMEOUT 1000 +#define CFG_MACB_AUTONEG_TIMEOUT 5000000 + +struct macb_dma_desc { + u32 addr; + u32 ctrl; +}; + +#define RXADDR_USED 0x00000001 +#define RXADDR_WRAP 0x00000002 + +#define RXBUF_FRMLEN_MASK 0x00000fff +#define RXBUF_FRAME_START 0x00004000 +#define RXBUF_FRAME_END 0x00008000 +#define RXBUF_TYPEID_MATCH 0x00400000 +#define RXBUF_ADDR4_MATCH 0x00800000 +#define RXBUF_ADDR3_MATCH 0x01000000 +#define RXBUF_ADDR2_MATCH 0x02000000 +#define RXBUF_ADDR1_MATCH 0x04000000 +#define RXBUF_BROADCAST 0x80000000 + +#define TXBUF_FRMLEN_MASK 0x000007ff +#define TXBUF_FRAME_END 0x00008000 +#define TXBUF_NOCRC 0x00010000 +#define TXBUF_EXHAUSTED 0x08000000 +#define TXBUF_UNDERRUN 0x10000000 +#define TXBUF_MAXRETRY 0x20000000 +#define TXBUF_WRAP 0x40000000 +#define TXBUF_USED 0x80000000 + +struct macb_device { + void *regs; + + unsigned int rx_tail; + unsigned int tx_head; + unsigned int tx_tail; + + void *rx_buffer; + void *tx_buffer; + struct macb_dma_desc *rx_ring; + struct macb_dma_desc *tx_ring; + + unsigned long rx_buffer_dma; + unsigned long rx_ring_dma; + unsigned long tx_ring_dma; + + const struct device *dev; + struct eth_device netdev; + unsigned short phy_addr; +}; +#define to_macb(_nd) container_of(_nd, struct macb_device, netdev) + +static void macb_mdio_write(struct macb_device *macb, u8 reg, u16 value) +{ + unsigned long netctl; + unsigned long netstat; + unsigned long frame; + + netctl = macb_readl(macb, NCR); + netctl |= MACB_BIT(MPE); + macb_writel(macb, NCR, netctl); + + frame = (MACB_BF(SOF, 1) + | MACB_BF(RW, 1) + | MACB_BF(PHYA, macb->phy_addr) + | MACB_BF(REGA, reg) + | MACB_BF(CODE, 2) + | MACB_BF(DATA, value)); + macb_writel(macb, MAN, frame); + + do { + netstat = macb_readl(macb, NSR); + } while (!(netstat & MACB_BIT(IDLE))); + + netctl = macb_readl(macb, NCR); + netctl &= ~MACB_BIT(MPE); + macb_writel(macb, NCR, netctl); +} + +static u16 macb_mdio_read(struct macb_device *macb, u8 reg) +{ + unsigned long netctl; + unsigned long netstat; + unsigned long frame; + + netctl = macb_readl(macb, NCR); + netctl |= MACB_BIT(MPE); + macb_writel(macb, NCR, netctl); + + frame = (MACB_BF(SOF, 1) + | MACB_BF(RW, 2) + | MACB_BF(PHYA, macb->phy_addr) + | MACB_BF(REGA, reg) + | MACB_BF(CODE, 2)); + macb_writel(macb, MAN, frame); + + do { + netstat = macb_readl(macb, NSR); + } while (!(netstat & MACB_BIT(IDLE))); + + frame = macb_readl(macb, MAN); + + netctl = macb_readl(macb, NCR); + netctl &= ~MACB_BIT(MPE); + macb_writel(macb, NCR, netctl); + + return MACB_BFEXT(DATA, frame); +} + +#if (CONFIG_COMMANDS & CFG_CMD_NET) + +static int macb_send(struct eth_device *netdev, volatile void *packet, + int length) +{ + struct macb_device *macb = to_macb(netdev); + unsigned long paddr, ctrl; + unsigned int tx_head = macb->tx_head; + int i; + + paddr = dma_map_single(packet, length, DMA_TO_DEVICE); + + ctrl = length & TXBUF_FRMLEN_MASK; + ctrl |= TXBUF_FRAME_END; + if (tx_head == (CFG_MACB_TX_RING_SIZE - 1)) { + ctrl |= TXBUF_WRAP; + macb->tx_head = 0; + } else + macb->tx_head++; + + macb->tx_ring[tx_head].ctrl = ctrl; + macb->tx_ring[tx_head].addr = paddr; + macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE) | MACB_BIT(TSTART)); + + /* + * I guess this is necessary because the networking core may + * re-use the transmit buffer as soon as we return... + */ + i = 0; + while (!(macb->tx_ring[tx_head].ctrl & TXBUF_USED)) { + if (i > CFG_MACB_TX_TIMEOUT) { + printf("%s: TX timeout\n", netdev->name); + break; + } + udelay(1); + i++; + } + + dma_unmap_single(packet, length, paddr); + + if (i <= CFG_MACB_TX_TIMEOUT) { + ctrl = macb->tx_ring[tx_head].ctrl; + if (ctrl & TXBUF_UNDERRUN) + printf("%s: TX underrun\n", netdev->name); + if (ctrl & TXBUF_EXHAUSTED) + printf("%s: TX buffers exhausted in mid frame\n", + netdev->name); + } + + /* No one cares anyway */ + return 0; +} + +static void reclaim_rx_buffers(struct macb_device *macb, + unsigned int new_tail) +{ + unsigned int i; + + i = macb->rx_tail; + while (i > new_tail) { + macb->rx_ring[i].addr &= ~RXADDR_USED; + i++; + if (i > CFG_MACB_RX_RING_SIZE) + i = 0; + } + + while (i < new_tail) { + macb->rx_ring[i].addr &= ~RXADDR_USED; + i++; + } + + macb->rx_tail = new_tail; +} + +static int macb_recv(struct eth_device *netdev) +{ + struct macb_device *macb = to_macb(netdev); + unsigned int rx_tail = macb->rx_tail; + void *buffer; + int length; + int wrapped = 0; + u32 status; + + for (;;) { + if (!(macb->rx_ring[rx_tail].addr & RXADDR_USED)) + return -1; + + status = macb->rx_ring[rx_tail].ctrl; + if (status & RXBUF_FRAME_START) { + if (rx_tail != macb->rx_tail) + reclaim_rx_buffers(macb, rx_tail); + wrapped = 0; + } + + if (status & RXBUF_FRAME_END) { + buffer = macb->rx_buffer + 128 * macb->rx_tail; + length = status & RXBUF_FRMLEN_MASK; + if (wrapped) { + unsigned int headlen, taillen; + + headlen = 128 * (CFG_MACB_RX_RING_SIZE + - macb->rx_tail); + taillen = length - headlen; + memcpy((void *)NetRxPackets[0], + buffer, headlen); + memcpy((void *)NetRxPackets[0] + headlen, + macb->rx_buffer, taillen); + buffer = (void *)NetRxPackets[0]; + } + + NetReceive(buffer, length); + if (++rx_tail >= CFG_MACB_RX_RING_SIZE) + rx_tail = 0; + reclaim_rx_buffers(macb, rx_tail); + } else { + if (++rx_tail >= CFG_MACB_RX_RING_SIZE) { + wrapped = 1; + rx_tail = 0; + } + } + } + + return 0; +} + +static int macb_phy_init(struct macb_device *macb) +{ + struct eth_device *netdev = &macb->netdev; + u32 ncfgr; + u16 phy_id, status, adv, lpa; + int media, speed, duplex; + int i; + + /* Check if the PHY is up to snuff... */ + phy_id = macb_mdio_read(macb, MII_PHYSID1); + if (phy_id == 0xffff) { + printf("%s: No PHY present\n", netdev->name); + return 0; + } + + adv = ADVERTISE_CSMA | ADVERTISE_ALL; + macb_mdio_write(macb, MII_ADVERTISE, adv); + printf("%s: Starting autonegotiation...\n", netdev->name); + macb_mdio_write(macb, MII_BMCR, (BMCR_ANENABLE + | BMCR_ANRESTART)); + +#if 0 + for (i = 0; i < 9; i++) + printf("mii%d: 0x%04x\n", i, macb_mdio_read(macb, i)); +#endif + + for (i = 0; i < CFG_MACB_AUTONEG_TIMEOUT / 100; i++) { + status = macb_mdio_read(macb, MII_BMSR); + if (status & BMSR_ANEGCOMPLETE) + break; + udelay(100); + } + + if (status & BMSR_ANEGCOMPLETE) + printf("%s: Autonegotiation complete\n", netdev->name); + else + printf("%s: Autonegotiation timed out (status=0x%04x)\n", + netdev->name, status); + + if (!(status & BMSR_LSTATUS)) { + for (i = 0; i < CFG_MACB_AUTONEG_TIMEOUT / 100; i++) { + udelay(100); + status = macb_mdio_read(macb, MII_BMSR); + if (status & BMSR_LSTATUS) + break; + } + } + + if (!(status & BMSR_LSTATUS)) { + printf("%s: link down (status: 0x%04x)\n", + netdev->name, status); + return 0; + } else { + lpa = macb_mdio_read(macb, MII_LPA); + media = mii_nway_result(lpa & adv); + speed = (media & (ADVERTISE_100FULL | ADVERTISE_100HALF) + ? 1 : 0); + duplex = (media & ADVERTISE_FULL) ? 1 : 0; + printf("%s: link up, %sMbps %s-duplex (lpa: 0x%04x)\n", + netdev->name, + speed ? "100" : "10", + duplex ? "full" : "half", + lpa); + + ncfgr = macb_readl(macb, NCFGR); + ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD)); + if (speed) + ncfgr |= MACB_BIT(SPD); + if (duplex) + ncfgr |= MACB_BIT(FD); + macb_writel(macb, NCFGR, ncfgr); + return 1; + } +} + +static int macb_init(struct eth_device *netdev, bd_t *bd) +{ + struct macb_device *macb = to_macb(netdev); + unsigned long paddr; + u32 hwaddr_bottom; + u16 hwaddr_top; + int i; + + /* + * macb_halt should have been called at some point before now, + * so we'll assume the controller is idle. + */ + + /* initialize DMA descriptors */ + paddr = macb->rx_buffer_dma; + for (i = 0; i < CFG_MACB_RX_RING_SIZE; i++) { + if (i == (CFG_MACB_RX_RING_SIZE - 1)) + paddr |= RXADDR_WRAP; + macb->rx_ring[i].addr = paddr; + macb->rx_ring[i].ctrl = 0; + paddr += 128; + } + for (i = 0; i < CFG_MACB_TX_RING_SIZE; i++) { + macb->tx_ring[i].addr = 0; + if (i == (CFG_MACB_TX_RING_SIZE - 1)) + macb->tx_ring[i].ctrl = TXBUF_USED | TXBUF_WRAP; + else + macb->tx_ring[i].ctrl = TXBUF_USED; + } + macb->rx_tail = macb->tx_head = macb->tx_tail = 0; + + macb_writel(macb, RBQP, macb->rx_ring_dma); + macb_writel(macb, TBQP, macb->tx_ring_dma); + + /* set hardware address */ + hwaddr_bottom = cpu_to_le32(*((u32 *)netdev->enetaddr)); + macb_writel(macb, SA1B, hwaddr_bottom); + hwaddr_top = cpu_to_le16(*((u16 *)(netdev->enetaddr + 4))); + macb_writel(macb, SA1T, hwaddr_top); + + /* choose RMII or MII mode. This depends on the board */ +#ifdef CONFIG_RMII + macb_writel(macb, USRIO, 0); +#else + macb_writel(macb, USRIO, MACB_BIT(MII)); +#endif + + if (!macb_phy_init(macb)) + return 0; + + /* Enable TX and RX */ + macb_writel(macb, NCR, MACB_BIT(TE) | MACB_BIT(RE)); + + return 1; +} + +static void macb_halt(struct eth_device *netdev) +{ + struct macb_device *macb = to_macb(netdev); + u32 ncr, tsr; + + /* Halt the controller and wait for any ongoing transmission to end. */ + ncr = macb_readl(macb, NCR); + ncr |= MACB_BIT(THALT); + macb_writel(macb, NCR, ncr); + + do { + tsr = macb_readl(macb, TSR); + } while (tsr & MACB_BIT(TGO)); + + /* Disable TX and RX, and clear statistics */ + macb_writel(macb, NCR, MACB_BIT(CLRSTAT)); +} + +int macb_eth_initialize(int id, void *regs, unsigned int phy_addr) +{ + struct macb_device *macb; + struct eth_device *netdev; + unsigned long macb_hz; + u32 ncfgr; + + macb = malloc(sizeof(struct macb_device)); + if (!macb) { + printf("Error: Failed to allocate memory for MACB%d\n", id); + return -1; + } + memset(macb, 0, sizeof(struct macb_device)); + + netdev = &macb->netdev; + + macb->rx_buffer = dma_alloc_coherent(CFG_MACB_RX_BUFFER_SIZE, + &macb->rx_buffer_dma); + macb->rx_ring = dma_alloc_coherent(CFG_MACB_RX_RING_SIZE + * sizeof(struct macb_dma_desc), + &macb->rx_ring_dma); + macb->tx_ring = dma_alloc_coherent(CFG_MACB_TX_RING_SIZE + * sizeof(struct macb_dma_desc), + &macb->tx_ring_dma); + + macb->regs = regs; + macb->phy_addr = phy_addr; + + sprintf(netdev->name, "macb%d", id); + netdev->init = macb_init; + netdev->halt = macb_halt; + netdev->send = macb_send; + netdev->recv = macb_recv; + + /* + * Do some basic initialization so that we at least can talk + * to the PHY + */ + macb_hz = get_macb_pclk_rate(id); + if (macb_hz < 20000000) + ncfgr = MACB_BF(CLK, MACB_CLK_DIV8); + else if (macb_hz < 40000000) + ncfgr = MACB_BF(CLK, MACB_CLK_DIV16); + else if (macb_hz < 80000000) + ncfgr = MACB_BF(CLK, MACB_CLK_DIV32); + else + ncfgr = MACB_BF(CLK, MACB_CLK_DIV64); + + macb_writel(macb, NCFGR, ncfgr); + + eth_register(netdev); + + return 0; +} + +#endif /* (CONFIG_COMMANDS & CFG_CMD_NET) */ + +#if (CONFIG_COMMANDS & CFG_CMD_MII) + +int miiphy_read(unsigned char addr, unsigned char reg, unsigned short *value) +{ + unsigned long netctl; + unsigned long netstat; + unsigned long frame; + int iflag; + + iflag = disable_interrupts(); + netctl = macb_readl(&macb, EMACB_NCR); + netctl |= MACB_BIT(MPE); + macb_writel(&macb, EMACB_NCR, netctl); + if (iflag) + enable_interrupts(); + + frame = (MACB_BF(SOF, 1) + | MACB_BF(RW, 2) + | MACB_BF(PHYA, addr) + | MACB_BF(REGA, reg) + | MACB_BF(CODE, 2)); + macb_writel(&macb, EMACB_MAN, frame); + + do { + netstat = macb_readl(&macb, EMACB_NSR); + } while (!(netstat & MACB_BIT(IDLE))); + + frame = macb_readl(&macb, EMACB_MAN); + *value = MACB_BFEXT(DATA, frame); + + iflag = disable_interrupts(); + netctl = macb_readl(&macb, EMACB_NCR); + netctl &= ~MACB_BIT(MPE); + macb_writel(&macb, EMACB_NCR, netctl); + if (iflag) + enable_interrupts(); + + return 0; +} + +int miiphy_write(unsigned char addr, unsigned char reg, unsigned short value) +{ + unsigned long netctl; + unsigned long netstat; + unsigned long frame; + int iflag; + + iflag = disable_interrupts(); + netctl = macb_readl(&macb, EMACB_NCR); + netctl |= MACB_BIT(MPE); + macb_writel(&macb, EMACB_NCR, netctl); + if (iflag) + enable_interrupts(); + + frame = (MACB_BF(SOF, 1) + | MACB_BF(RW, 1) + | MACB_BF(PHYA, addr) + | MACB_BF(REGA, reg) + | MACB_BF(CODE, 2) + | MACB_BF(DATA, value)); + macb_writel(&macb, EMACB_MAN, frame); + + do { + netstat = macb_readl(&macb, EMACB_NSR); + } while (!(netstat & MACB_BIT(IDLE))); + + iflag = disable_interrupts(); + netctl = macb_readl(&macb, EMACB_NCR); + netctl &= ~MACB_BIT(MPE); + macb_writel(&macb, EMACB_NCR, netctl); + if (iflag) + enable_interrupts(); + + return 0; +} + +#endif /* (CONFIG_COMMANDS & CFG_CMD_MII) */ + +#endif /* CONFIG_MACB */ diff --git a/drivers/macb.h b/drivers/macb.h new file mode 100644 index 00000000000..c778e4ee493 --- /dev/null +++ b/drivers/macb.h @@ -0,0 +1,269 @@ +/* + * Copyright (C) 2005-2006 Atmel Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __DRIVERS_MACB_H__ +#define __DRIVERS_MACB_H__ + +/* MACB register offsets */ +#define MACB_NCR 0x0000 +#define MACB_NCFGR 0x0004 +#define MACB_NSR 0x0008 +#define MACB_TSR 0x0014 +#define MACB_RBQP 0x0018 +#define MACB_TBQP 0x001c +#define MACB_RSR 0x0020 +#define MACB_ISR 0x0024 +#define MACB_IER 0x0028 +#define MACB_IDR 0x002c +#define MACB_IMR 0x0030 +#define MACB_MAN 0x0034 +#define MACB_PTR 0x0038 +#define MACB_PFR 0x003c +#define MACB_FTO 0x0040 +#define MACB_SCF 0x0044 +#define MACB_MCF 0x0048 +#define MACB_FRO 0x004c +#define MACB_FCSE 0x0050 +#define MACB_ALE 0x0054 +#define MACB_DTF 0x0058 +#define MACB_LCOL 0x005c +#define MACB_EXCOL 0x0060 +#define MACB_TUND 0x0064 +#define MACB_CSE 0x0068 +#define MACB_RRE 0x006c +#define MACB_ROVR 0x0070 +#define MACB_RSE 0x0074 +#define MACB_ELE 0x0078 +#define MACB_RJA 0x007c +#define MACB_USF 0x0080 +#define MACB_STE 0x0084 +#define MACB_RLE 0x0088 +#define MACB_TPF 0x008c +#define MACB_HRB 0x0090 +#define MACB_HRT 0x0094 +#define MACB_SA1B 0x0098 +#define MACB_SA1T 0x009c +#define MACB_SA2B 0x00a0 +#define MACB_SA2T 0x00a4 +#define MACB_SA3B 0x00a8 +#define MACB_SA3T 0x00ac +#define MACB_SA4B 0x00b0 +#define MACB_SA4T 0x00b4 +#define MACB_TID 0x00b8 +#define MACB_TPQ 0x00bc +#define MACB_USRIO 0x00c0 +#define MACB_WOL 0x00c4 + +/* Bitfields in NCR */ +#define MACB_LB_OFFSET 0 +#define MACB_LB_SIZE 1 +#define MACB_LLB_OFFSET 1 +#define MACB_LLB_SIZE 1 +#define MACB_RE_OFFSET 2 +#define MACB_RE_SIZE 1 +#define MACB_TE_OFFSET 3 +#define MACB_TE_SIZE 1 +#define MACB_MPE_OFFSET 4 +#define MACB_MPE_SIZE 1 +#define MACB_CLRSTAT_OFFSET 5 +#define MACB_CLRSTAT_SIZE 1 +#define MACB_INCSTAT_OFFSET 6 +#define MACB_INCSTAT_SIZE 1 +#define MACB_WESTAT_OFFSET 7 +#define MACB_WESTAT_SIZE 1 +#define MACB_BP_OFFSET 8 +#define MACB_BP_SIZE 1 +#define MACB_TSTART_OFFSET 9 +#define MACB_TSTART_SIZE 1 +#define MACB_THALT_OFFSET 10 +#define MACB_THALT_SIZE 1 +#define MACB_NCR_TPF_OFFSET 11 +#define MACB_NCR_TPF_SIZE 1 +#define MACB_TZQ_OFFSET 12 +#define MACB_TZQ_SIZE 1 + +/* Bitfields in NCFGR */ +#define MACB_SPD_OFFSET 0 +#define MACB_SPD_SIZE 1 +#define MACB_FD_OFFSET 1 +#define MACB_FD_SIZE 1 +#define MACB_BIT_RATE_OFFSET 2 +#define MACB_BIT_RATE_SIZE 1 +#define MACB_JFRAME_OFFSET 3 +#define MACB_JFRAME_SIZE 1 +#define MACB_CAF_OFFSET 4 +#define MACB_CAF_SIZE 1 +#define MACB_NBC_OFFSET 5 +#define MACB_NBC_SIZE 1 +#define MACB_NCFGR_MTI_OFFSET 6 +#define MACB_NCFGR_MTI_SIZE 1 +#define MACB_UNI_OFFSET 7 +#define MACB_UNI_SIZE 1 +#define MACB_BIG_OFFSET 8 +#define MACB_BIG_SIZE 1 +#define MACB_EAE_OFFSET 9 +#define MACB_EAE_SIZE 1 +#define MACB_CLK_OFFSET 10 +#define MACB_CLK_SIZE 2 +#define MACB_RTY_OFFSET 12 +#define MACB_RTY_SIZE 1 +#define MACB_PAE_OFFSET 13 +#define MACB_PAE_SIZE 1 +#define MACB_RBOF_OFFSET 14 +#define MACB_RBOF_SIZE 2 +#define MACB_RLCE_OFFSET 16 +#define MACB_RLCE_SIZE 1 +#define MACB_DRFCS_OFFSET 17 +#define MACB_DRFCS_SIZE 1 +#define MACB_EFRHD_OFFSET 18 +#define MACB_EFRHD_SIZE 1 +#define MACB_IRXFCS_OFFSET 19 +#define MACB_IRXFCS_SIZE 1 + +/* Bitfields in NSR */ +#define MACB_NSR_LINK_OFFSET 0 +#define MACB_NSR_LINK_SIZE 1 +#define MACB_MDIO_OFFSET 1 +#define MACB_MDIO_SIZE 1 +#define MACB_IDLE_OFFSET 2 +#define MACB_IDLE_SIZE 1 + +/* Bitfields in TSR */ +#define MACB_UBR_OFFSET 0 +#define MACB_UBR_SIZE 1 +#define MACB_COL_OFFSET 1 +#define MACB_COL_SIZE 1 +#define MACB_TSR_RLE_OFFSET 2 +#define MACB_TSR_RLE_SIZE 1 +#define MACB_TGO_OFFSET 3 +#define MACB_TGO_SIZE 1 +#define MACB_BEX_OFFSET 4 +#define MACB_BEX_SIZE 1 +#define MACB_COMP_OFFSET 5 +#define MACB_COMP_SIZE 1 +#define MACB_UND_OFFSET 6 +#define MACB_UND_SIZE 1 + +/* Bitfields in RSR */ +#define MACB_BNA_OFFSET 0 +#define MACB_BNA_SIZE 1 +#define MACB_REC_OFFSET 1 +#define MACB_REC_SIZE 1 +#define MACB_OVR_OFFSET 2 +#define MACB_OVR_SIZE 1 + +/* Bitfields in ISR/IER/IDR/IMR */ +#define MACB_MFD_OFFSET 0 +#define MACB_MFD_SIZE 1 +#define MACB_RCOMP_OFFSET 1 +#define MACB_RCOMP_SIZE 1 +#define MACB_RXUBR_OFFSET 2 +#define MACB_RXUBR_SIZE 1 +#define MACB_TXUBR_OFFSET 3 +#define MACB_TXUBR_SIZE 1 +#define MACB_ISR_TUND_OFFSET 4 +#define MACB_ISR_TUND_SIZE 1 +#define MACB_ISR_RLE_OFFSET 5 +#define MACB_ISR_RLE_SIZE 1 +#define MACB_TXERR_OFFSET 6 +#define MACB_TXERR_SIZE 1 +#define MACB_TCOMP_OFFSET 7 +#define MACB_TCOMP_SIZE 1 +#define MACB_ISR_LINK_OFFSET 9 +#define MACB_ISR_LINK_SIZE 1 +#define MACB_ISR_ROVR_OFFSET 10 +#define MACB_ISR_ROVR_SIZE 1 +#define MACB_HRESP_OFFSET 11 +#define MACB_HRESP_SIZE 1 +#define MACB_PFR_OFFSET 12 +#define MACB_PFR_SIZE 1 +#define MACB_PTZ_OFFSET 13 +#define MACB_PTZ_SIZE 1 + +/* Bitfields in MAN */ +#define MACB_DATA_OFFSET 0 +#define MACB_DATA_SIZE 16 +#define MACB_CODE_OFFSET 16 +#define MACB_CODE_SIZE 2 +#define MACB_REGA_OFFSET 18 +#define MACB_REGA_SIZE 5 +#define MACB_PHYA_OFFSET 23 +#define MACB_PHYA_SIZE 5 +#define MACB_RW_OFFSET 28 +#define MACB_RW_SIZE 2 +#define MACB_SOF_OFFSET 30 +#define MACB_SOF_SIZE 2 + +/* Bitfields in USRIO */ +#define MACB_MII_OFFSET 0 +#define MACB_MII_SIZE 1 +#define MACB_EAM_OFFSET 1 +#define MACB_EAM_SIZE 1 +#define MACB_TX_PAUSE_OFFSET 2 +#define MACB_TX_PAUSE_SIZE 1 +#define MACB_TX_PAUSE_ZERO_OFFSET 3 +#define MACB_TX_PAUSE_ZERO_SIZE 1 + +/* Bitfields in WOL */ +#define MACB_IP_OFFSET 0 +#define MACB_IP_SIZE 16 +#define MACB_MAG_OFFSET 16 +#define MACB_MAG_SIZE 1 +#define MACB_ARP_OFFSET 17 +#define MACB_ARP_SIZE 1 +#define MACB_SA1_OFFSET 18 +#define MACB_SA1_SIZE 1 +#define MACB_WOL_MTI_OFFSET 19 +#define MACB_WOL_MTI_SIZE 1 + +/* Constants for CLK */ +#define MACB_CLK_DIV8 0 +#define MACB_CLK_DIV16 1 +#define MACB_CLK_DIV32 2 +#define MACB_CLK_DIV64 3 + +/* Constants for MAN register */ +#define MACB_MAN_SOF 1 +#define MACB_MAN_WRITE 1 +#define MACB_MAN_READ 2 +#define MACB_MAN_CODE 2 + +/* Bit manipulation macros */ +#define MACB_BIT(name) \ + (1 << MACB_##name##_OFFSET) +#define MACB_BF(name,value) \ + (((value) & ((1 << MACB_##name##_SIZE) - 1)) \ + << MACB_##name##_OFFSET) +#define MACB_BFEXT(name,value)\ + (((value) >> MACB_##name##_OFFSET) \ + & ((1 << MACB_##name##_SIZE) - 1)) +#define MACB_BFINS(name,value,old) \ + (((old) & ~(((1 << MACB_##name##_SIZE) - 1) \ + << MACB_##name##_OFFSET)) \ + | MACB_BF(name,value)) + +/* Register access macros */ +#define macb_readl(port,reg) \ + readl((port)->regs + MACB_##reg) +#define macb_writel(port,reg,value) \ + writel((value), (port)->regs + MACB_##reg) + +#endif /* __DRIVERS_MACB_H__ */ -- cgit v1.3.1 From 2a26ec4732efd7a308d0bbc97714c1d75ef1173b Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 18 Apr 2007 17:07:26 +0200 Subject: Cleanup, update CHANGELOG Sigend-off-by: Wolfgang Denk --- CHANGELOG | 493 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/Makefile | 7 +- 2 files changed, 497 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/CHANGELOG b/CHANGELOG index fc3d4a7b23e..780a2c41e96 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -65,6 +65,239 @@ Date: Sat Apr 14 21:16:54 2007 +0200 Update CHANGELOG +commit 8e6875183cdca91c134408d119d4abcd48ef6856 +Author: Haavard Skinnemoen +Date: Sun Dec 17 18:56:46 2006 +0100 + + AVR32: Enable MMC support + + Set up the portmux for the MMC interface and enable the MMC driver + along with support for DOS partitions, ext2 and FAT filesystems. + + Signed-off-by: Haavard Skinnemoen + +commit fc26c97bb6df41b4a95662c34054fe912387bf38 +Author: Haavard Skinnemoen +Date: Fri Jan 20 10:03:53 2006 +0100 + + Atmel MCI driver + + Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs. + + The AT91 ARM-based CPUs use basically the same hardware, so it should + be possible to share this driver, but no effort has been made so far. + + Hardware documentation can be found in the AT32AP7000 data sheet, + which can be downloaded from + + http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 + + Signed-off-by: Haavard Skinnemoen + +commit 05fdab1ef6a10d049a50021a86f1226f444d9b9f +Author: Haavard Skinnemoen +Date: Sun Dec 17 18:55:37 2006 +0100 + + AVR32: Add clk and gpio infrastructure for mmci + + Implement functions for configuring the mmci pins, as well as + functions for getting the clock rate of the mmci controller. + + Signed-off-by: Haavard Skinnemoen + +commit 7fac3f69e9f05c5e5326681976c35d129324c4de +Author: Haavard Skinnemoen +Date: Sun Dec 17 18:53:56 2006 +0100 + + Enable partition support with MMC + + Include implementations of init_part() and get_partition_info() when + CONFIG_MMC is set. + + Signed-off-by: Haavard Skinnemoen + +commit 9a24f477a1ed5bb0f74377c985d754ebbfa44872 +Author: Haavard Skinnemoen +Date: Sun Dec 17 17:14:30 2006 +0100 + + AVR32: Enable networking + + Implement MACB initialization for AVR32 and ATSTK1000, and turn + everything on, including the MACB driver. + + Signed-off-by: Haavard Skinnemoen + +commit 5c1fe1ffffd1750a7e47e5a2e2cd600c00e4f009 +Author: Haavard Skinnemoen +Date: Fri Jan 20 10:03:34 2006 +0100 + + Atmel MACB ethernet driver + + Driver for the Atmel MACB on-chip ethernet controller. + + This driver has been tested on the ATSTK1000 board with a AT32AP7000 + CPU. It should probably work on AT91SAM926x as well with some minor + modifications. + + Hardware documentation can be found in the AT32AP7000 data sheet, + which can be downloaded from + + http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 + + Signed-off-by: Haavard Skinnemoen + +commit b4ec9c2d43d894729bb633bfdbdfa95a962c1556 +Author: Haavard Skinnemoen +Date: Sun Dec 17 16:56:14 2006 +0100 + + AVR32: Add clk and gpio infrastructure for macb0 and macb1 + + Implement functions for configuring the macb0 and macb1 pins, as + well as functions for getting the clock rate of the various + busses the macb ethernet controllers are connected to. + + Signed-off-by: Haavard Skinnemoen + +commit d5acb95b16a0a74c643524342c3437e765426d05 +Author: Haavard Skinnemoen +Date: Sun Dec 17 15:39:15 2006 +0100 + + AVR32: Implement simple DMA memory allocator + + Implement dma_alloc_coherent() which returns cache-aligned + uncacheable memory. + + Signed-off-by: Haavard Skinnemoen + +commit 91975b0fea773c9e681fea8cf3349669f27685ee +Author: Haavard Skinnemoen +Date: Sun Dec 17 15:46:02 2006 +0100 + + Import from the Linux kernel + + Instead of creating yet another set of MII register definitions + in the macb driver, here's a complete set of definitions for everyone + to use. + + Signed-off-by: Haavard Skinnemoen + +commit 1b804b229556a4d862da93c0ec94e79419364b2c +Author: Haavard Skinnemoen +Date: Wed Mar 21 19:47:36 2007 +0100 + + AVR32: Include more commands for ATSTK1000 + + Include the imi, imls and jffs commands sets by default on ATSTK1000. + Also define CONFIG_BOOTARGS to something more useful, define + CONFIG_BOOTCOMMAND and enable autoboot by default. + + Signed-off-by: Haavard Skinnemoen + +commit 9c0deb5ae3ea0189f2e08ac29ef1316f1fb8548d +Author: Haavard Skinnemoen +Date: Wed Mar 21 19:44:48 2007 +0100 + + AVR32: Provide a definition of struct stat + + Copy the definition of struct stat from the Linux kernel. + + Signed-off-by: Haavard Skinnemoen + +commit 12f099c08167a7a51aeee623bc16dafd0841271c +Author: Haavard Skinnemoen +Date: Sun Dec 17 14:46:06 2006 +0100 + + AVR32: Use initdram() instead of board_init_memories() + + Conform to the "standard" interface and use initdram() instead of + board_init_memories() on AVR32. This enables us to get rid of the + sdram_size member of the global_data struct as well. + + Signed-off-by: Haavard Skinnemoen + +commit 1f4f2121c2685182eb87fa9a9b799d1917387a1c +Author: Haavard Skinnemoen +Date: Mon Nov 20 15:53:10 2006 +0100 + + AVR32: Relocate u-boot to SDRAM + + Relocate the u-boot image into SDRAM like everyone else does. This + means that we can handle much larger .data and .bss than we used to. + + Signed-off-by: Haavard Skinnemoen + +commit df548d3c3e2bbc40258713167859ffc2ce99a900 +Author: Haavard Skinnemoen +Date: Sun Nov 19 18:06:53 2006 +0100 + + AVR32: Resource management rewrite + + Rewrite the resource management code (i.e. I/O memory, clock gating, + gpio) so it doesn't depend on any global state. This is necessary + because this code is heavily used before relocation to RAM, so we + can't write to any global variables. + + As an added bonus, this makes u-boot's memory footprint a bit smaller, + although some functionality has been left out; all clocks are enabled + all the time, and there's no checking for gpio line conflicts. + + Signed-off-by: Haavard Skinnemoen + +commit 03d1e1365796cd15d1726e8a51fd8b5be50b2fe9 +Author: Haavard Skinnemoen +Date: Sat Nov 18 18:01:13 2006 +0100 + + AVR32: Clean up memory-map.h for at32ap7000 + + Convert spaces to tabs (must have missed this one last time around), + sort the entries by address and group them together by bus + connectivity. + + Signed-off-by: Haavard Skinnemoen + +commit 28c699ef69f4b6cdf252e4747b7b590028a88981 +Author: Haavard Skinnemoen +Date: Sat Nov 18 17:32:31 2006 +0100 + + AVR32: Build position-independent u-boot + + Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot + position independent. This will make relocation a lot easier. + + -mno-init-got means that gcc shouldn't emit code to load the GOT + address into r6 in every function prologue. We do it once and for + all in the early startup assembly code, so enabling this option + makes u-boot a bit faster and smaller. + + The assembly parts have always been position-independent, so no code + changes should be necessary. + + Signed-off-by: Haavard Skinnemoen + +commit 5374b36de91d006d1df9536259fa9f66b01aa3aa +Author: Haavard Skinnemoen +Date: Sat Nov 18 17:24:31 2006 +0100 + + AVR32: Use avr32-linux- cross-compilation prefix by default + + It doesn't really matter which toolchain you use to compile u-boot, + but the avr32-linux one is probably what most people have installed. + + Signed-off-by: Haavard Skinnemoen + +commit c841beeddebece0039e724fb27f4d1a39ee1c6b6 +Author: Haavard Skinnemoen +Date: Sat Nov 18 17:15:30 2006 +0100 + + AVR32: Split start_u_boot into board_init_f and board_init_r + + Split the avr32 initialization code into a function to run before + relocation, board_init_f and a function to run after relocation, + board_init_r. For now, board_init_f simply calls board_init_r + at the end. + + Signed-off-by: Haavard Skinnemoen + commit 37403005cfe6bb13964d450f6a48a0b0f2f7017e Author: Heiko Schocher Date: Sat Apr 14 05:26:48 2007 +0200 @@ -843,6 +1076,12 @@ Date: Tue Mar 6 07:47:04 2007 +0100 Signed-off-by: Stefan Roese +commit 647d3c3eed0da1d1505eecabe0b0fab96f956e68 +Author: Wolfgang Denk +Date: Sun Mar 4 01:36:05 2007 +0100 + + Some code cleanup. + commit 781e026c8aa6f7e9eb5f0e72cc4d20971219b148 Author: Kim Phillips Date: Wed Feb 28 00:02:04 2007 -0600 @@ -1714,6 +1953,15 @@ Date: Tue Jan 23 13:25:22 2007 +0100 [ColdFire MCF5271 family] Add CPU detection based on the value of Chip Identification Register (CIR). +commit fdef388758506765d4d6a7155c8f1584c63ff581 +Author: roy zang +Date: Mon Jan 22 13:19:21 2007 +0800 + + use CFG_WRITE_SWAPPED_DATA define instead of define CFG_FLASH_CFI_SWAP + The patch by Heiko Schocher on Jan, 19, 2007 + fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support + mpc7448hpc2 board. + commit a4012396645533aef218354eeba754dff0deace8 Author: Wolfgang Denk Date: Fri Jan 19 23:08:39 2007 +0100 @@ -2129,6 +2377,72 @@ Date: Fri Dec 8 16:23:08 2006 +0100 automatic update mechanism +commit 9d27b3a0685ff99fc477983f315c04d49f657a8a +Author: roy zang +Date: Mon Dec 4 17:56:59 2006 +0800 + + Slight code clean up. + Add comments, delete duplicate define and remove spaces. + Signed-off-by: Roy Zang + +commit 4dbcd69e3e2776ea334590d5768e3692c5fae5c1 +Author: roy zang +Date: Mon Dec 4 17:54:21 2006 +0800 + + Introduce PLL_CFG[0:4] table for processor 7448/7447A/7455/7457. The original + multiplier table can not refect the real PLL clock behavior of these + processors. Please refer to the hardware specification for detailed + information of the corresponding processors. + Signed-off-by: Roy Zang + +commit 4efe20c9579011d9987f62ed7d35ee8cdc1cf0e0 +Author: roy zang +Date: Mon Dec 4 14:46:23 2006 +0800 + + Remove the static MAC address, ip address, server ip, netmask and + gateway ip for network setting. + Signed-off-by: Roy Zang + +commit 6f12c61cf31ed73d72ddfcfc712a854a3a177aaf +Author: roy zang +Date: Mon Dec 4 14:33:08 2006 +0800 + + Remove the duplicate memory test code for mpc744ihpc2 board. + If a memory test is needed, please use the functions in + post/memory.c or memtest command. + Signed-off-by: Roy Zang + +commit c9c1eeed7dd193fa65fb194654132040d49d4d3a +Author: roy zang +Date: Fri Dec 1 19:01:25 2006 +0800 + + Fix the exception occuring in RAM table search issue. + The original search_one_table() function code can only processes the search + for the exception occurring in FLASH/ROM, because the exception and fixup + table usually locate in FLASH. If the exception address is also in + FLASH, it will be OK. + If the exception occurs in RAM, after the u-boot relocation, a + relocation offset should be added. + + clean up the code in cpu/74xx_7xx/cpu.c + + Signed-off-by: Roy Zang + +commit ee311214e0d216f904feea269599d0934bf71f23 +Author: roy zang +Date: Fri Dec 1 11:47:36 2006 +0800 + + Clean up the code according to codestyle: + (1) remove some C++ comments. + (2) remove trailing white space. + (3) remove trailing empty line. + (4) Indentation by table. + (5) remove {} in one line condition. + (6) add space before '(' in function call. + Remove some weird printf () output. + Add necessary comments. + Modified Makefile to support building in a separate directory. + commit dd520bf314c7add4183c5191692180f576f96b60 Author: Wolfgang Denk Date: Thu Nov 30 18:02:20 2006 +0100 @@ -2835,12 +3149,191 @@ Date: Thu Sep 7 07:39:46 2006 -0700 Signed-off-by: Nick Spence +commit 4831c8b8a97799da77923d6bbb4c260c0d45521c +Author: roy zang +Date: Fri Nov 3 13:10:00 2006 +0800 + + Remove some unused CFG define. + undef CFG_DRAM_TEST + +commit 99c09c4dec34f77c243bf51bea532e3f339410ad +Author: roy zang +Date: Fri Nov 3 13:07:36 2006 +0800 + + Change the TEXT_BASE from 0xFFF00000 to 0xFF000000. + Both work. 0xFF000000 seems more reasonable. + commit c59200443072353044aa4bf737a5a60f9a9af231 Author: Wolfgang Denk Date: Thu Nov 2 15:15:01 2006 +0100 Release U-Boot 1.1.6 +commit c1fbe4103a0d6c8957f912af902d705ba67836f2 +Author: roy zang +Date: Thu Nov 2 19:14:48 2006 +0800 + + This patch comes from Yuli's posted patch on 8/8/2006 + titled "CFI Driver Little-Endian write Issue". + + http://sourceforge.net/mailarchive/message.php?msg_id=36311999 + + If that patch applied, please discard this one. + Until now , I do not see his patch is applied. So please apply this one. + + Signed-off-by: Yuli Barcohen + Signed-off-by: Roy Zang + +commit b825f158e449e1e9cf74c08e572955e122394c96 +Author: roy zang +Date: Thu Nov 2 19:12:31 2006 +0800 + + Tsi108 on chip i2c support. + + The i2c Interface provides a master-only, serial interface that can be + used for initializing Tsi108/Tsi109 registers from an EEPROM after a + device reset. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 9226e7d6f09b9a1ac074cd918c81225a4689bba8 +Author: roy zang +Date: Thu Nov 2 19:11:06 2006 +0800 + + Tsi108 on chip pci controller support. + + If there is no pci card, the tsi108/109 pci configure read will + cause a machine check exception to the processor. PCI error should + also be cleared after the read. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit d1927cee977126e547ceeba23e4f978f377cfb8f +Author: roy zang +Date: Thu Nov 2 19:08:55 2006 +0800 + + Tundra tsi108 on chip Ethernet controller support. + + The following is a brief description of the Ethernet controller: + The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent + Gigabit Ethernet ports,E0 and E1. It uses a single Management interface + to manage the two physical connection devices (PHYs). Each Ethernet port + has its own statistics monitor that tracks and reports key interface + statistics. Each port supports a 256-entry hash table for address + filtering. In addition, each port is bridged to the Switch Fabric + through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO. + + Each Ethernet port also has a pair of internal Ethernet DMA channels to + support the transmit and receive data flows. The Ethernet DMA channels + use descriptors set up in memory, the memory map of the device, and + access via the Switch Fabric. The Ethernet Controller?s DMA arbiter + handles arbitration for the Switch Fabric. The Controller also + has a register businterface for register accesses and status monitor + control. + + The PMD (Physical Media Device) interface operates in MII, GMII, or TBI + modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs. + The GMII and TBI modes are used to connect with Gigabit PMDs. Internal + data flows to and from the Ethernet Controller through the Switch Fabric. + + Each Ethernet port uses its transmit and receive DMA channels to manage + data flows through buffer descriptors that are predefined by the + system (the descriptors can exist anywhere in the system memory map). + These descriptors are data structures that point to buffers filled + with data ready to transmit over Ethernet, or they point to empty + buffers ready to receive data from Ethernet. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 78aa0c3427f3ecdeb34aabfbbe2dd23b6ad8f40e +Author: roy zang +Date: Thu Nov 2 19:01:33 2006 +0800 + + Tundra tsi108 header file. + + The Tundra Semiconductor Corporation (Tundra) Tsi108 is a host bridge for + PowerPC processors that offers numerous system interconnect options for + embedded application designers. The Tsi108 can interconnect 60x or + MPX processors to PCI/X peripherals, DDR2-400 memory, Gigabit Ethernet, + and Flash. Provided the macro define for tsi108 chip. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 87c4db09699c6b89176b31004afcb83eb1585d47 +Author: roy zang +Date: Thu Nov 2 18:59:15 2006 +0800 + + Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support. + mpc7448hpc2 board support high level code:tsi108 init + mpc7448hpc2. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 27801b8ab11c61b577e45742a515bb3b23b80241 +Author: roy zang +Date: Thu Nov 2 18:57:21 2006 +0800 + + Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support. + Make ,config.mk and link file for the mpc7448hpc2 board. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit c6411c0c3bbc79f9ba8aef58296a42d8f9d8a0a6 +Author: roy zang +Date: Thu Nov 2 18:55:04 2006 +0800 + + Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support. + The mpc7448hpc2 board support header file. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 625bb5ddb50b243f931262ca8c46956409471917 +Author: roy zang +Date: Thu Nov 2 18:52:21 2006 +0800 + + Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support. + The mpc7448hpc2 board support low level assemble language init code. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 4c52783b3d024e153c4972b97332e314bc3bdc46 +Author: roy zang +Date: Thu Nov 2 18:49:51 2006 +0800 + + General code modification for mpc7448hpc2 board support. + 1. Add 7447A and 7448 processor support. + 2. Add the following flags. + + CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically + (such as by switch on board), this flag should be set. + + CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot + relocates to RAM, this flag should be set. + + CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the + system hang in exception, this flag should be set. + + There is a design issue for tsi108/109 pci configure read. When pci scan + the slots, if there is no pci card, the tsi108/9 will cause a machine + check exception for mpc7448 processor. + + Signed-off-by: Alexandre Bounine + Signed-off-by: Roy Zang + +commit 69366bf42f22d67efce8da3f8c40a43d4a3c2695 +Author: roy zang +Date: Thu Nov 2 18:34:47 2006 +0800 + + Add README file for mpc7448hpc2 board. + Signed-off-by: Roy Zang + commit 25721b5cec2be4bce79cfade17ec8f6aa1e67526 Author: Bartlomiej Sieka Date: Wed Nov 1 02:04:38 2006 +0100 diff --git a/drivers/Makefile b/drivers/Makefile index df9fbf2aae1..d68cba682be 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -35,8 +35,8 @@ COBJS = 3c589.o 5701rls.o ali512x.o atmel_usart.o \ lan91c96.o macb.o \ natsemi.o ne2000.o netarm_eth.o netconsole.o \ ns16550.o ns8382x.o ns87308.o ns7520_eth.o omap1510_i2c.o \ - omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o tsi108_pci.o\ - tsi108_i2c.o pcnet.o plb2800_eth.o \ + omap24xx_i2c.o pci.o pci_auto.o pci_indirect.o \ + pcnet.o plb2800_eth.o \ ps2ser.o ps2mult.o pc_keyb.o \ rtl8019.o rtl8139.o rtl8169.o \ s3c4510b_eth.o s3c4510b_uart.o \ @@ -45,7 +45,8 @@ COBJS = 3c589.o 5701rls.o ali512x.o atmel_usart.o \ serial_pl010.o serial_pl011.o serial_xuartlite.o \ sl811_usb.o sm501.o smc91111.o smiLynxEM.o \ status_led.o sym53c8xx.o systemace.o ahci.o \ - ti_pci1410a.o tigon3.o tsec.o tsi108_eth.o\ + ti_pci1410a.o tigon3.o tsec.o \ + tsi108_eth.o tsi108_i2c.o tsi108_pci.o \ usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \ videomodes.o w83c553f.o \ ks8695eth.o \ -- cgit v1.3.1 From 81f481ca708ed6a56bf9c410e3191dbad581c565 Mon Sep 17 00:00:00 2001 From: Andy Fleming Date: Mon, 23 Apr 2007 02:24:28 -0500 Subject: Enable 8544 support * Add support to the Makefile * Add 8544 configuration support to the tsec driver * Add 8544 SVR numbers to processor.h Signed-off-by: Ed Swarthout Signed-off-by: Jon Loeliger --- MAKEALL | 8 ++++---- Makefile | 3 +++ drivers/tsec.c | 6 +++++- drivers/tsec.h | 3 ++- include/asm-ppc/processor.h | 11 +++++++++-- 5 files changed, 23 insertions(+), 8 deletions(-) (limited to 'drivers') diff --git a/MAKEALL b/MAKEALL index 0f0ec296f26..59aec2867f0 100755 --- a/MAKEALL +++ b/MAKEALL @@ -142,10 +142,10 @@ LIST_83xx=" \ ######################################################################### LIST_85xx=" \ - MPC8540ADS MPC8540EVAL MPC8541CDS MPC8548CDS \ - MPC8555CDS MPC8560ADS PM854 PM856 \ - sbc8540 sbc8560 stxgp3 TQM8540 \ - TQM8541 TQM8555 TQM8560 \ + MPC8540ADS MPC8540EVAL MPC8541CDS MPC8544DS \ + MPC8548CDS MPC8555CDS MPC8560ADS PM854 \ + PM856 sbc8540 sbc8560 stxgp3 \ + TQM8540 TQM8541 TQM8555 TQM8560 \ " ######################################################################### diff --git a/Makefile b/Makefile index 94cda54c731..d447a9610d4 100644 --- a/Makefile +++ b/Makefile @@ -1730,6 +1730,9 @@ MPC8560ADS_config: unconfig MPC8541CDS_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8541cds cds +MPC8544DS_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8544ds freescale + MPC8548CDS_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8548cds cds diff --git a/drivers/tsec.c b/drivers/tsec.c index 3f11eb03b41..ed35f227c1b 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -5,7 +5,7 @@ * terms of the GNU Public License, Version 2, incorporated * herein by reference. * - * Copyright 2004 Freescale Semiconductor. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. * (C) Copyright 2003, Motorola, Inc. * author Andy Fleming * @@ -66,7 +66,11 @@ struct tsec_info_struct { */ static struct tsec_info_struct tsec_info[] = { #if defined(CONFIG_MPC85XX_TSEC1) || defined(CONFIG_MPC83XX_TSEC1) +#if defined(CONFIG_MPC8544DS) + {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX}, +#else {TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX}, +#endif #elif defined(CONFIG_MPC86XX_TSEC1) {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX}, #else diff --git a/drivers/tsec.h b/drivers/tsec.h index 422bc669229..7bf3dee2b68 100644 --- a/drivers/tsec.h +++ b/drivers/tsec.h @@ -7,7 +7,7 @@ * terms of the GNU Public License, Version 2, incorporated * herein by reference. * - * Copyright 2004 Freescale Semiconductor. + * Copyright 2004, 2007 Freescale Semiconductor, Inc. * (C) Copyright 2003, Motorola, Inc. * maintained by Xianghua Xiao (x.xiao@motorola.com) * author Andy Fleming @@ -65,6 +65,7 @@ #define ECNTRL_INIT_SETTINGS 0x00001000 #define ECNTRL_TBI_MODE 0x00000020 #define ECNTRL_R100 0x00000008 +#define ECNTRL_SGMII_MODE 0x00000002 #define miim_end -2 #define miim_read -1 diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 058596275f4..944cbe90c38 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -232,6 +232,9 @@ #define HID0_BHTE (1<<2) /* Branch History Table Enable */ #define HID0_BTCD (1<<1) /* Branch target cache disable */ #define SPRN_HID1 0x3F1 /* Hardware Implementation Register 1 */ +#define HID1_RFXE (1<<17) /* Read Fault Exception Enable */ +#define HID1_ASTME (1<<13) /* Address bus streaming mode */ +#define HID1_ABE (1<<12) /* Address broadcast enable */ #define SPRN_IABR 0x3F2 /* Instruction Address Breakpoint Register */ #ifndef CONFIG_BOOKE #define SPRN_IAC1 0x3F4 /* Instruction Address Compare 1 */ @@ -415,10 +418,12 @@ #define SPRN_IVOR15 0x19f /* Interrupt Vector Offset Register 15 */ /* e500 definitions */ -#define SPRN_L1CSR0 0x3f2 /* L1 Cache Control and Status Register 0 */ +#define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */ +#define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */ #define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */ #define L1CSR0_DCE 0x00000001 /* Data Cache Enable */ -#define SPRN_L1CSR1 0x3f3 /* L1 Cache Control and Status Register 1 */ +#define SPRN_L1CSR1 0x3f3 /* L1 Instruction Cache Control and Status Register 1 */ +#define L1CSR1_CPE 0x00010000 /* Instruction Cache Parity Enable */ #define L1CSR1_ICFI 0x00000002 /* Instruction Cache Flash Invalidate */ #define L1CSR1_ICE 0x00000001 /* Instruction Cache Enable */ @@ -840,6 +845,8 @@ #define SVR_8560 0x8070 #define SVR_8555 0x8079 #define SVR_8541 0x807A +#define SVR_8544 0x8034 +#define SVR_8544_E 0x803C #define SVR_8548 0x8031 #define SVR_8548_E 0x8039 #define SVR_8641 0x8090 -- cgit v1.3.1 From af1c2b84bf27c8565baddc82d1abb93700d10e2e Mon Sep 17 00:00:00 2001 From: David Updegraff Date: Fri, 20 Apr 2007 14:34:48 -0500 Subject: Add support for treating unknown PHYs as generic PHYs. When bringing up u-boot on new boards, PHY support sometimes gets neglected. Most PHYs don't really need any special support, though. By adding a generic entry that always matches if nothing else does, we can provide support for "unsupported" PHYs for the tsec. The generic PHY driver supports most PHYs, including gigabit. Signed-off-by: David Updegraff Signed-off-by: Andy Fleming --- drivers/tsec.c | 93 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 93 insertions(+) (limited to 'drivers') diff --git a/drivers/tsec.c b/drivers/tsec.c index ed35f227c1b..25566a73387 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -385,6 +385,76 @@ uint mii_parse_sr(uint mii_reg, struct tsec_private * priv) return 0; } +/* Generic function which updates the speed and duplex. If + * autonegotiation is enabled, it uses the AND of the link + * partner's advertised capabilities and our advertised + * capabilities. If autonegotiation is disabled, we use the + * appropriate bits in the control register. + * + * Stolen from Linux's mii.c and phy_device.c + */ +uint mii_parse_link(uint mii_reg, struct tsec_private *priv) +{ + /* We're using autonegotiation */ + if (mii_reg & PHY_BMSR_AUTN_ABLE) { + uint lpa = 0; + uint gblpa = 0; + + /* Check for gigabit capability */ + if (mii_reg & PHY_BMSR_EXT) { + /* We want a list of states supported by + * both PHYs in the link + */ + gblpa = read_phy_reg(priv, PHY_1000BTSR); + gblpa &= read_phy_reg(priv, PHY_1000BTCR) << 2; + } + + /* Set the baseline so we only have to set them + * if they're different + */ + priv->speed = 10; + priv->duplexity = 0; + + /* Check the gigabit fields */ + if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) { + priv->speed = 1000; + + if (gblpa & PHY_1000BTSR_1000FD) + priv->duplexity = 1; + + /* We're done! */ + return 0; + } + + lpa = read_phy_reg(priv, PHY_ANAR); + lpa &= read_phy_reg(priv, PHY_ANLPAR); + + if (lpa & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) { + priv->speed = 100; + + if (lpa & PHY_ANLPAR_TXFD) + priv->duplexity = 1; + + } else if (lpa & PHY_ANLPAR_10FD) + priv->duplexity = 1; + } else { + uint bmcr = read_phy_reg(priv, PHY_BMCR); + + priv->speed = 10; + priv->duplexity = 0; + + if (bmcr & PHY_BMCR_DPLX) + priv->duplexity = 1; + + if (bmcr & PHY_BMCR_1000_MBPS) + priv->speed = 1000; + else if (bmcr & PHY_BMCR_100_MBPS) + priv->speed = 100; + } + + return 0; +} + /* * Parse the BCM54xx status register for speed and duplex information. * The linux sungem_phy has this information, but in a table format. @@ -722,6 +792,7 @@ static void startup_tsec(struct eth_device *dev) /* Start up the PHY */ if(priv->phyinfo) phy_run_commands(priv, priv->phyinfo->startup); + adjust_link(dev); /* Enable Transmit and Receive */ @@ -1092,6 +1163,27 @@ struct phy_info phy_info_dm9161 = { {miim_end,} }, }; +/* a generic flavor. */ +struct phy_info phy_info_generic = { + 0, + "Unknown/Generic PHY", + 32, + (struct phy_cmd[]) { /* config */ + {PHY_BMCR, PHY_BMCR_RESET, NULL}, + {PHY_BMCR, PHY_BMCR_AUTON|PHY_BMCR_RST_NEG, NULL}, + {miim_end,} + }, + (struct phy_cmd[]) { /* startup */ + {PHY_BMSR, miim_read, NULL}, + {PHY_BMSR, miim_read, &mii_parse_sr}, + {PHY_BMSR, miim_read, &mii_parse_link}, + {miim_end,} + }, + (struct phy_cmd[]) { /* shutdown */ + {miim_end,} + } +}; + uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv) { @@ -1207,6 +1299,7 @@ struct phy_info *phy_info[] = { &phy_info_lxt971, &phy_info_VSC8244, &phy_info_dp83865, + &phy_info_generic, NULL }; -- cgit v1.3.1 From a79886590593ba1d667c840caa4940c61639f18f Mon Sep 17 00:00:00 2001 From: Thomas Knobloch Date: Sat, 5 May 2007 07:04:42 +0200 Subject: NAND: Wrong calculation of page number in nand_block_bad() In case that there is no memory based bad block table available the function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call nand_block_bad() directly. When parameter 'getchip' is set to zero, nand_block_bad() will not right shift the offset to calculate the correct page number. Signed-off-by: Thomas Knobloch Signed-off-by: Stefan Roese --- drivers/nand/nand_base.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/nand/nand_base.c b/drivers/nand/nand_base.c index 8495829900c..c6fee18222b 100644 --- a/drivers/nand/nand_base.c +++ b/drivers/nand/nand_base.c @@ -427,8 +427,9 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) struct nand_chip *this = mtd->priv; u16 bad; + page = (int)(ofs >> this->page_shift) & this->pagemask; + if (getchip) { - page = (int)(ofs >> this->page_shift); chipnr = (int)(ofs >> this->chip_shift); /* Grab the lock and see if the device is available */ @@ -436,18 +437,17 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) /* Select the NAND device */ this->select_chip(mtd, chipnr); - } else - page = (int) ofs; + } if (this->options & NAND_BUSWIDTH_16) { - this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page & this->pagemask); + this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page); bad = cpu_to_le16(this->read_word(mtd)); if (this->badblockpos & 0x1) bad >>= 1; if ((bad & 0xFF) != 0xff) res = 1; } else { - this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page & this->pagemask); + this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page); if (this->read_byte(mtd) != 0xff) res = 1; } -- cgit v1.3.1 From 2f15278c2eb911c668b4fe562130b78cf554d139 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sat, 5 May 2007 18:23:11 +0200 Subject: Coding stylke cleanup; update CHANGELOG. Signed-off-by: Wolfgang Denk --- CHANGELOG | 65 +++++++++++++++++++++++++++++++++++ board/freescale/mpc8544ds/mpc8544ds.c | 22 +++++------- cpu/mpc85xx/cpu.c | 18 +++++----- cpu/ppc4xx/4xx_enet.c | 4 +-- drivers/tsec.c | 2 +- include/configs/MPC8568MDS.h | 2 +- 6 files changed, 87 insertions(+), 26 deletions(-) (limited to 'drivers') diff --git a/CHANGELOG b/CHANGELOG index 0bb6bc5c167..184e9418cba 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,9 +1,44 @@ +commit 885ec89b648a899a2f32393fd3ffd9f7234c4402 +Author: Wolfgang Denk +Date: Sat May 5 18:05:02 2007 +0200 + + Add STX GP3 SSA board to MAKEALL script; update CHANGELOG. + + Signed-off-by: Wolfgang Denk + commit 5499645b3fe17a548af9dfc479ca6e2455f179a2 Author: Wolfgang Denk Date: Sat May 5 17:15:50 2007 +0200 Make "file" command happy with some config.mk files; update CHANGELOG +commit e3b8c78bc2489c27ae020986ef0eaca684866cef +Author: Jeffrey Mann +Date: Sat May 5 08:32:14 2007 +0200 + + ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHz + + The AMCC Secquoia board has been changed in a new revision from using a + 33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD + indicates the difference. This patch reads that bit and uses the correct + clock speed for the board. This code is backward compatable will all + prior boards. All prior boards will be read as 33.000. + + Signed-off-by: Jeffrey Mann + Signed-off-by: Stefan Roese + +commit f544ff6656fca263ed1ebe39899b6d95da67c8b8 +Author: Stefan Roese +Date: Sat May 5 08:29:01 2007 +0200 + + ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND booting + + Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big + for the 4k NAND boot image so define bus_frequency to 133MHz here + which is save for the refresh counter setup. + + Signed-off-by: Stefan Roese + commit a79886590593ba1d667c840caa4940c61639f18f Author: Thomas Knobloch Date: Sat May 5 07:04:42 2007 +0200 @@ -124,6 +159,22 @@ Date: Fri Mar 16 13:02:53 2007 -0500 Signed-off-by: James Yang Signed-off-by: Jon Loeliger +commit 8b39501d28754e72726ce7fb02310e56dbdf116a +Author: Stefan Roese +Date: Sun Apr 29 14:13:01 2007 +0200 + + ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driver + + Signed-off-by: Stefan Roese + +commit 37ed6cdd4159195bfad68d8a237f6adda8f482cb +Author: Matthias Fuchs +Date: Tue Apr 24 14:03:45 2007 +0200 + + ppc4xx: setup 440EPx/GRx ZMII/RGMII bridge depending on PFC register content. + + Signed-off-by: Matthias Fuchs + commit 66ed6cca3f340f7a8a06d9272ae2ef8e96f0273d Author: Andy Fleming Date: Mon Apr 23 02:37:47 2007 -0500 @@ -429,6 +480,20 @@ Date: Thu Apr 19 23:14:39 2007 -0400 Also moved the libfdt.a requirement into the main Makefile. That is The U-Boot Way. +commit d21686263574e95cb3e9e9b0496f968b1b897fdb +Author: Stefan Roese +Date: Thu Apr 19 09:53:52 2007 +0200 + + ppc4xx: Fix chip select timing for SysACE access on AMCC Katmai + + Previous versions used full wait states for the chip select #1 which + is connected to the Xilinix SystemACE controller on the AMCC Katmai + evaluation board. This leads to really slow access and therefore low + performance. This patch now sets up the chip select a lot faster + resulting in much better read/write performance of the Linux driver. + + Signed-off-by: Stefan Roese + commit 37837828d89084879bee2f2b8c7c68d4695940df Author: Wolfgang Denk Date: Wed Apr 18 17:49:29 2007 +0200 diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c index 90599348d79..4ff1da93017 100644 --- a/board/freescale/mpc8544ds/mpc8544ds.c +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -52,7 +52,7 @@ int checkboard (void) volatile immap_t *immap = (immap_t *) CFG_CCSRBAR; volatile ccsr_gur_t *gur = &immap->im_gur; - if ((uint)&gur->porpllsr != 0xe00e0000) { + if ((uint)&gur->porpllsr != 0xe00e0000) { printf("immap size error %x\n",&gur->porpllsr); } printf ("Board: MPC8544DS\n"); @@ -79,7 +79,6 @@ initdram(int board_type) return dram_size; } - #if defined(CFG_DRAM_TEST) int testdram(void) @@ -119,8 +118,6 @@ testdram(void) } #endif - - int last_stage_init(void) { return 0; @@ -190,16 +187,15 @@ get_board_sys_clk(ulong dummy) void ft_board_setup(void *blob, bd_t *bd) { - u32 *p; - int len; + u32 *p; + int len; - ft_cpu_setup(blob, bd); + ft_cpu_setup(blob, bd); - p = ft_get_prop(blob, "/memory/reg", &len); - if (p != NULL) { - *p++ = cpu_to_be32(bd->bi_memstart); - *p = cpu_to_be32(bd->bi_memsize); - } + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } } #endif - diff --git a/cpu/mpc85xx/cpu.c b/cpu/mpc85xx/cpu.c index 63176d2841d..7735a52ccf1 100644 --- a/cpu/mpc85xx/cpu.c +++ b/cpu/mpc85xx/cpu.c @@ -71,14 +71,14 @@ int checkcpu (void) puts("8548_E"); break; case SVR_8544: - puts("8544"); - break; - case SVR_8544_E: - puts("8544_E"); - break; - case SVR_8568_E: - puts("8568_E"); - break; + puts("8544"); + break; + case SVR_8544_E: + puts("8544_E"); + break; + case SVR_8568_E: + puts("8568_E"); + break; default: puts("Unknown"); break; @@ -157,7 +157,7 @@ int do_reset (cmd_tbl_t *cmdtp, bd_t *bd, int flag, int argc, char *argv[]) /* e500 v2 core has reset control register */ volatile unsigned int * rstcr; rstcr = (volatile unsigned int *)(CFG_IMMR + 0xE00B0); - *rstcr = 0x2; /* HRESET_REQ */ + *rstcr = 0x2; /* HRESET_REQ */ }else{ /* * Initiate hard reset in debug control register DBCR0 diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index be4e82405eb..1200d021af6 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -344,7 +344,7 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) mfsdr(sdr_pfc1, pfc1); pfc1 &= SDR0_PFC1_SELECT_MASK; - switch (pfc1) { + switch (pfc1) { case SDR0_PFC1_SELECT_CONFIG_2: /* 1 x GMII port */ out32 (ZMII_FER, 0x00); @@ -361,7 +361,7 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) break; case SDR0_PFC1_SELECT_CONFIG_6: /* 2 x SMII ports */ - out32 (ZMII_FER, + out32 (ZMII_FER, ((ZMII_FER_SMII) << ZMII_FER_V(0)) | ((ZMII_FER_SMII) << ZMII_FER_V(1))); out32 (RGMII_FER, 0x00000000); diff --git a/drivers/tsec.c b/drivers/tsec.c index 25566a73387..b4187739cb0 100644 --- a/drivers/tsec.c +++ b/drivers/tsec.c @@ -67,7 +67,7 @@ struct tsec_info_struct { static struct tsec_info_struct tsec_info[] = { #if defined(CONFIG_MPC85XX_TSEC1) || defined(CONFIG_MPC83XX_TSEC1) #if defined(CONFIG_MPC8544DS) - {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX}, + {TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX}, #else {TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX}, #endif diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 66293c5221e..3f65644fdd4 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -149,7 +149,7 @@ extern unsigned long get_clock_freq(void); #define CFG_BR1_PRELIM 0xf8000801 #define CFG_OR1_PRELIM 0xffffe9f7 -//#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} +/*#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 512 /* sectors per device */ #undef CFG_FLASH_CHECKSUM -- cgit v1.3.1 From ebd0a0ae05a44769c4e27458ad4e9f3438250443 Mon Sep 17 00:00:00 2001 From: Mike Frysinger Date: Mon, 23 Apr 2007 13:54:24 +0200 Subject: [patch] use unsigned char in smc91111 driver for mac the v_mac variable in the smc91111 driver is declared as a signed char ... this causes problems when one of the bytes in the MAC is "signed" like 0xE0 because when it gets printed out, you get a display like: 0xFFFFFFE0 and that's no good Signed-off-by: Mike Frysinger --- drivers/smc91111.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/smc91111.c b/drivers/smc91111.c index f91e4b98436..8061f12979d 100644 --- a/drivers/smc91111.c +++ b/drivers/smc91111.c @@ -1538,9 +1538,9 @@ int eth_send(volatile void *packet, int length) { int smc_get_ethaddr (bd_t * bd) { int env_size, rom_valid, env_present = 0, reg; - char *s = NULL, *e, *v_mac, es[] = "11:22:33:44:55:66"; + char *s = NULL, *e, es[] = "11:22:33:44:55:66"; char s_env_mac[64]; - uchar v_env_mac[6], v_rom_mac[6]; + uchar v_env_mac[6], v_rom_mac[6], *v_mac; env_size = getenv_r ("ethaddr", s_env_mac, sizeof (s_env_mac)); if ((env_size > 0) && (env_size < sizeof (es))) { /* exit if env is bad */ @@ -1563,7 +1563,7 @@ int smc_get_ethaddr (bd_t * bd) if (!env_present) { /* if NO env */ if (rom_valid) { /* but ROM is valid */ - v_mac = (char *)v_rom_mac; + v_mac = v_rom_mac; sprintf (s_env_mac, "%02X:%02X:%02X:%02X:%02X:%02X", v_mac[0], v_mac[1], v_mac[2], v_mac[3], v_mac[4], v_mac[5]); @@ -1573,7 +1573,7 @@ int smc_get_ethaddr (bd_t * bd) return (-1); } } else { /* good env, don't care ROM */ - v_mac = (char *)v_env_mac; /* always use a good env over a ROM */ + v_mac = v_env_mac; /* always use a good env over a ROM */ } if (env_present && rom_valid) { /* if both env and ROM are good */ -- cgit v1.3.1 From b7598a43f2b421a713d8135e98a42c37d9eb9df0 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Mon, 23 Apr 2007 15:30:39 +0200 Subject: [PATCH] Avoid assigning PCI resources from zero address If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE core complains and IDE drivers fails to work. Also, assigning zero to a BAR was illegal according to PCI 2.1 (the later revisions seem to have excluded the sentence about "0" being considered an invalid address) -- so, use a reasonable starting value of 0x1000 (that's what the most Linux archs are using). Alternatively, one might have fixed the calls to pci_set_region() individually (some code even seems to have taken care of this issue) but that would have been a lot more work. :-) Signed-off-by: Sergei Shtylyov Acked-by: Stefan Roese --- drivers/pci_auto.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/pci_auto.c b/drivers/pci_auto.c index 969167555ea..f170c2db89e 100644 --- a/drivers/pci_auto.c +++ b/drivers/pci_auto.c @@ -34,7 +34,12 @@ void pciauto_region_init(struct pci_region* res) { - res->bus_lower = res->bus_start; + /* + * Avoid allocating PCI resources from address 0 -- this is illegal + * according to PCI 2.1 and moreover, this is known to cause Linux IDE + * drivers to fail. Use a reasonable starting value of 0x1000 instead. + */ + res->bus_lower = res->bus_start ? res->bus_start : 0x1000; } void pciauto_region_align(struct pci_region *res, unsigned long size) -- cgit v1.3.1