From a89c33db96a1e55319a286dd4c3c05ca64ac6bfd Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 24 May 2009 17:06:54 +0200 Subject: General help message cleanup Many of the help messages were not really helpful; for example, many commands that take no arguments would not print a correct synopsis line, but "No additional help available." which is not exactly wrong, but not helpful either. Commit ``Make "usage" messages more helpful.'' changed this partially. But it also became clear that lots of "Usage" and "Help" messages (fields "usage" and "help" in struct cmd_tbl_s respective) were actually redundant. This patch cleans this up - for example: Before: => help dtt dtt - Digital Thermometer and Thermostat Usage: dtt - Read temperature from digital thermometer and thermostat. After: => help dtt dtt - Read temperature from Digital Thermometer and Thermostat Usage: dtt Signed-off-by: Wolfgang Denk --- drivers/gpio/pca953x.c | 2 +- drivers/misc/ds4510.c | 8 +++++--- drivers/qe/qe.c | 5 +++-- 3 files changed, 9 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/gpio/pca953x.c b/drivers/gpio/pca953x.c index 1c5e314d9d5..e8273ee363d 100644 --- a/drivers/gpio/pca953x.c +++ b/drivers/gpio/pca953x.c @@ -221,7 +221,7 @@ U_BOOT_CMD( "pca953x invert pin 0|1\n" " - disable/enable polarity inversion for reads\n" "pca953x intput pin\n" - " - set pin as input and read value\n" + " - set pin as input and read value" ); #endif /* CONFIG_CMD_PCA953X */ diff --git a/drivers/misc/ds4510.c b/drivers/misc/ds4510.c index 8b5fbbc4565..f2510a38fd0 100644 --- a/drivers/misc/ds4510.c +++ b/drivers/misc/ds4510.c @@ -404,12 +404,14 @@ U_BOOT_CMD( "ds4510 pullup pin 0|1\n" " - disable/enable pullup on specified pin\n" "ds4510 nv 0|1\n" - " - make gpio and seeprom writes volatile/non-volatile\n" + " - make gpio and seeprom writes volatile/non-volatile" #ifdef CONFIG_CMD_DS4510_RST + "\n" "ds4510 rstdelay 0-3\n" - " - set reset output delay\n" + " - set reset output delay" #endif #ifdef CONFIG_CMD_DS4510_MEM + "\n" "ds4510 eeprom read addr off cnt\n" "ds4510 eeprom write addr off cnt\n" " - read/write 'cnt' bytes at EEPROM offset 'off'\n" @@ -418,7 +420,7 @@ U_BOOT_CMD( " - read/write 'cnt' bytes at SRAM-shadowed EEPROM offset 'off'\n" "ds4510 sram read addr off cnt\n" "ds4510 sram write addr off cnt\n" - " - read/write 'cnt' bytes at SRAM offset 'off'\n" + " - read/write 'cnt' bytes at SRAM offset 'off'" #endif ); #endif /* CONFIG_CMD_DS4510 */ diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c index f114fe06a42..918bfa748e0 100644 --- a/drivers/qe/qe.c +++ b/drivers/qe/qe.c @@ -473,5 +473,6 @@ U_BOOT_CMD( qe, 4, 0, qe_cmd, "QUICC Engine commands", "fw [] - Upload firmware binary at address to " - "the QE,\n\twith optional length verification.\n" - ); + "the QE,\n" + "\twith optional length verification." +); -- cgit v1.2.3