From 72d7beabf72867da0a2e4dd37381cc3838ca8316 Mon Sep 17 00:00:00 2001 From: Stefan Agner Date: Fri, 12 Sep 2014 13:06:35 +0200 Subject: mtd: nand: add Freescale vf610_nfc driver This adds initial support for Freescale NFC (NAND Flash Controller) found in ARM Vybrid SoC's, Power Architecture MPC5125 and others. The driver is called vf610_nfc since this is the first supported and tested hardware platform supported by the driver. Signed-off-by: Stefan Agner Acked-by: Bill Pringlemeir --- drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/vf610_nfc.c | 724 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 725 insertions(+) create mode 100644 drivers/mtd/nand/vf610_nfc.c (limited to 'drivers') diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index bf1312a373a..eef86d1ecab 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -51,6 +51,7 @@ obj-$(CONFIG_NAND_KB9202) += kb9202_nand.o obj-$(CONFIG_NAND_KIRKWOOD) += kirkwood_nand.o obj-$(CONFIG_NAND_KMETER1) += kmeter1_nand.o obj-$(CONFIG_NAND_MPC5121_NFC) += mpc5121_nfc.o +obj-$(CONFIG_NAND_VF610_NFC) += vf610_nfc.o obj-$(CONFIG_NAND_MXC) += mxc_nand.o obj-$(CONFIG_NAND_MXS) += mxs_nand.o obj-$(CONFIG_NAND_NDFC) += ndfc.o diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c new file mode 100644 index 00000000000..7feb3a7b1e7 --- /dev/null +++ b/drivers/mtd/nand/vf610_nfc.c @@ -0,0 +1,724 @@ +/* + * Copyright 2009-2014 Freescale Semiconductor, Inc. and others + * + * Description: MPC5125, VF610, MCF54418 and Kinetis K70 Nand driver. + * Ported to U-Boot by Stefan Agner + * Based on RFC driver posted on Kernel Mailing list by Bill Pringlemeir + * Jason ported to M54418TWR and MVFA5. + * Authors: Stefan Agner + * Bill Pringlemeir + * Shaohui Xie + * Jason Jin + * + * Based on original driver mpc5121_nfc.c. + * + * This is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Limitations: + * - Untested on MPC5125 and M54418. + * - DMA not used. + * - 2K pages or less. + * - Only 2K page w. 64+OOB and hardware ECC. + */ + +#include +#include + +#include +#include +#include + +#include +#include +#include + +/* Register Offsets */ +#define NFC_FLASH_CMD1 0x3F00 +#define NFC_FLASH_CMD2 0x3F04 +#define NFC_COL_ADDR 0x3F08 +#define NFC_ROW_ADDR 0x3F0c +#define NFC_ROW_ADDR_INC 0x3F14 +#define NFC_FLASH_STATUS1 0x3F18 +#define NFC_FLASH_STATUS2 0x3F1c +#define NFC_CACHE_SWAP 0x3F28 +#define NFC_SECTOR_SIZE 0x3F2c +#define NFC_FLASH_CONFIG 0x3F30 +#define NFC_IRQ_STATUS 0x3F38 + +/* Addresses for NFC MAIN RAM BUFFER areas */ +#define NFC_MAIN_AREA(n) ((n) * 0x1000) + +#define PAGE_2K 0x0800 +#define OOB_64 0x0040 + +/* + * NFC_CMD2[CODE] values. See section: + * - 31.4.7 Flash Command Code Description, Vybrid manual + * - 23.8.6 Flash Command Sequencer, MPC5125 manual + * + * Briefly these are bitmasks of controller cycles. + */ +#define READ_PAGE_CMD_CODE 0x7EE0 +#define PROGRAM_PAGE_CMD_CODE 0x7FC0 +#define ERASE_CMD_CODE 0x4EC0 +#define READ_ID_CMD_CODE 0x4804 +#define RESET_CMD_CODE 0x4040 +#define STATUS_READ_CMD_CODE 0x4068 + +/* NFC ECC mode define */ +#define ECC_BYPASS 0 +#define ECC_45_BYTE 6 + +/*** Register Mask and bit definitions */ + +/* NFC_FLASH_CMD1 Field */ +#define CMD_BYTE2_MASK 0xFF000000 +#define CMD_BYTE2_SHIFT 24 + +/* NFC_FLASH_CM2 Field */ +#define CMD_BYTE1_MASK 0xFF000000 +#define CMD_BYTE1_SHIFT 24 +#define CMD_CODE_MASK 0x00FFFF00 +#define CMD_CODE_SHIFT 8 +#define BUFNO_MASK 0x00000006 +#define BUFNO_SHIFT 1 +#define START_BIT (1<<0) + +/* NFC_COL_ADDR Field */ +#define COL_ADDR_MASK 0x0000FFFF +#define COL_ADDR_SHIFT 0 + +/* NFC_ROW_ADDR Field */ +#define ROW_ADDR_MASK 0x00FFFFFF +#define ROW_ADDR_SHIFT 0 +#define ROW_ADDR_CHIP_SEL_RB_MASK 0xF0000000 +#define ROW_ADDR_CHIP_SEL_RB_SHIFT 28 +#define ROW_ADDR_CHIP_SEL_MASK 0x0F000000 +#define ROW_ADDR_CHIP_SEL_SHIFT 24 + +/* NFC_FLASH_STATUS2 Field */ +#define STATUS_BYTE1_MASK 0x000000FF + +/* NFC_FLASH_CONFIG Field */ +#define CONFIG_ECC_SRAM_ADDR_MASK 0x7FC00000 +#define CONFIG_ECC_SRAM_ADDR_SHIFT 22 +#define CONFIG_ECC_SRAM_REQ_BIT (1<<21) +#define CONFIG_DMA_REQ_BIT (1<<20) +#define CONFIG_ECC_MODE_MASK 0x000E0000 +#define CONFIG_ECC_MODE_SHIFT 17 +#define CONFIG_FAST_FLASH_BIT (1<<16) +#define CONFIG_16BIT (1<<7) +#define CONFIG_BOOT_MODE_BIT (1<<6) +#define CONFIG_ADDR_AUTO_INCR_BIT (1<<5) +#define CONFIG_BUFNO_AUTO_INCR_BIT (1<<4) +#define CONFIG_PAGE_CNT_MASK 0xF +#define CONFIG_PAGE_CNT_SHIFT 0 + +/* NFC_IRQ_STATUS Field */ +#define IDLE_IRQ_BIT (1<<29) +#define IDLE_EN_BIT (1<<20) +#define CMD_DONE_CLEAR_BIT (1<<18) +#define IDLE_CLEAR_BIT (1<<17) + +#define NFC_TIMEOUT (1000) + +/* ECC status placed at end of buffers. */ +#define ECC_SRAM_ADDR ((PAGE_2K+256-8) >> 3) +#define ECC_STATUS_MASK 0x80 +#define ECC_ERR_COUNT 0x3F + +/* + * ECC status is stored at NFC_CFG[ECCADD] +4 for little-endian + * and +7 for big-endian SOC. + */ +#ifdef CONFIG_VF610 +#define ECC_OFFSET 4 +#else +#define ECC_OFFSET 7 +#endif + +struct vf610_nfc { + struct mtd_info *mtd; + struct nand_chip chip; + void __iomem *regs; + uint column; + int spareonly; + int page; + /* Status and ID are in alternate locations. */ + int alt_buf; +#define ALT_BUF_ID 1 +#define ALT_BUF_STAT 2 + struct clk *clk; +}; + +#define mtd_to_nfc(_mtd) \ + (struct vf610_nfc *)((struct nand_chip *)_mtd->priv)->priv + +static u8 bbt_pattern[] = {'B', 'b', 't', '0' }; +static u8 mirror_pattern[] = {'1', 't', 'b', 'B' }; + +static struct nand_bbt_descr bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = bbt_pattern, +}; + +static struct nand_bbt_descr bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | + NAND_BBT_2BIT | NAND_BBT_VERSION, + .offs = 11, + .len = 4, + .veroffs = 15, + .maxblocks = 4, + .pattern = mirror_pattern, +}; + +static struct nand_ecclayout vf610_nfc_ecc45 = { + .eccbytes = 45, + .eccpos = {19, 20, 21, 22, 23, + 24, 25, 26, 27, 28, 29, 30, 31, + 32, 33, 34, 35, 36, 37, 38, 39, + 40, 41, 42, 43, 44, 45, 46, 47, + 48, 49, 50, 51, 52, 53, 54, 55, + 56, 57, 58, 59, 60, 61, 62, 63}, + .oobfree = { + {.offset = 8, + .length = 11} } +}; + +static inline u32 vf610_nfc_read(struct mtd_info *mtd, uint reg) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + + return readl(nfc->regs + reg); +} + +static inline void vf610_nfc_write(struct mtd_info *mtd, uint reg, u32 val) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + + writel(val, nfc->regs + reg); +} + +static inline void vf610_nfc_set(struct mtd_info *mtd, uint reg, u32 bits) +{ + vf610_nfc_write(mtd, reg, vf610_nfc_read(mtd, reg) | bits); +} + +static inline void vf610_nfc_clear(struct mtd_info *mtd, uint reg, u32 bits) +{ + vf610_nfc_write(mtd, reg, vf610_nfc_read(mtd, reg) & ~bits); +} + +static inline void vf610_nfc_set_field(struct mtd_info *mtd, u32 reg, + u32 mask, u32 shift, u32 val) +{ + vf610_nfc_write(mtd, reg, + (vf610_nfc_read(mtd, reg) & (~mask)) | val << shift); +} + +static inline void vf610_nfc_memcpy(void *dst, const void *src, size_t n) +{ + /* + * Use this accessor for the interal SRAM buffers. On ARM we can + * treat the SRAM buffer as if its memory, hence use memcpy + */ + memcpy(dst, src, n); +} + +/* Clear flags for upcoming command */ +static inline void vf610_nfc_clear_status(void __iomem *regbase) +{ + void __iomem *reg = regbase + NFC_IRQ_STATUS; + u32 tmp = __raw_readl(reg); + tmp |= CMD_DONE_CLEAR_BIT | IDLE_CLEAR_BIT; + __raw_writel(tmp, reg); +} + +/* Wait for complete operation */ +static inline void vf610_nfc_done(struct mtd_info *mtd) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + uint start; + + /* + * Barrier is needed after this write. This write need + * to be done before reading the next register the first + * time. + * vf610_nfc_set implicates such a barrier by using writel + * to write to the register. + */ + vf610_nfc_set(mtd, NFC_FLASH_CMD2, START_BIT); + + start = get_timer(0); + + while (!(vf610_nfc_read(mtd, NFC_IRQ_STATUS) & IDLE_IRQ_BIT)) { + if (get_timer(start) > NFC_TIMEOUT) { + printf("Timeout while waiting for !BUSY.\n"); + return; + } + } + vf610_nfc_clear_status(nfc->regs); +} + +static u8 vf610_nfc_get_id(struct mtd_info *mtd, int col) +{ + u32 flash_id; + + if (col < 4) { + flash_id = vf610_nfc_read(mtd, NFC_FLASH_STATUS1); + return (flash_id >> (3-col)*8) & 0xff; + } else { + flash_id = vf610_nfc_read(mtd, NFC_FLASH_STATUS2); + return flash_id >> 24; + } +} + +static u8 vf610_nfc_get_status(struct mtd_info *mtd) +{ + return vf610_nfc_read(mtd, NFC_FLASH_STATUS2) & STATUS_BYTE1_MASK; +} + +/* Single command */ +static void vf610_nfc_send_command(void __iomem *regbase, u32 cmd_byte1, + u32 cmd_code) +{ + void __iomem *reg = regbase + NFC_FLASH_CMD2; + u32 tmp; + vf610_nfc_clear_status(regbase); + + tmp = __raw_readl(reg); + tmp &= ~(CMD_BYTE1_MASK | CMD_CODE_MASK | BUFNO_MASK); + tmp |= cmd_byte1 << CMD_BYTE1_SHIFT; + tmp |= cmd_code << CMD_CODE_SHIFT; + __raw_writel(tmp, reg); +} + +/* Two commands */ +static void vf610_nfc_send_commands(void __iomem *regbase, u32 cmd_byte1, + u32 cmd_byte2, u32 cmd_code) +{ + void __iomem *reg = regbase + NFC_FLASH_CMD1; + u32 tmp; + vf610_nfc_send_command(regbase, cmd_byte1, cmd_code); + + tmp = __raw_readl(reg); + tmp &= ~CMD_BYTE2_MASK; + tmp |= cmd_byte2 << CMD_BYTE2_SHIFT; + __raw_writel(tmp, reg); +} + +static void vf610_nfc_addr_cycle(struct mtd_info *mtd, int column, int page) +{ + if (column != -1) { + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + if (nfc->chip.options | NAND_BUSWIDTH_16) + column = column/2; + vf610_nfc_set_field(mtd, NFC_COL_ADDR, COL_ADDR_MASK, + COL_ADDR_SHIFT, column); + } + if (page != -1) + vf610_nfc_set_field(mtd, NFC_ROW_ADDR, ROW_ADDR_MASK, + ROW_ADDR_SHIFT, page); +} + +/* Send command to NAND chip */ +static void vf610_nfc_command(struct mtd_info *mtd, unsigned command, + int column, int page) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + + nfc->column = max(column, 0); + nfc->spareonly = 0; + nfc->alt_buf = 0; + + switch (command) { + case NAND_CMD_PAGEPROG: + nfc->page = -1; + vf610_nfc_send_commands(nfc->regs, NAND_CMD_SEQIN, + command, PROGRAM_PAGE_CMD_CODE); + vf610_nfc_addr_cycle(mtd, column, page); + break; + + case NAND_CMD_RESET: + vf610_nfc_send_command(nfc->regs, command, RESET_CMD_CODE); + break; + /* + * NFC does not support sub-page reads and writes, + * so emulate them using full page transfers. + */ + case NAND_CMD_READOOB: + nfc->spareonly = 1; + case NAND_CMD_SEQIN: /* Pre-read for partial writes. */ + case NAND_CMD_READ0: + column = 0; + /* Already read? */ + if (nfc->page == page) + return; + nfc->page = page; + vf610_nfc_send_commands(nfc->regs, NAND_CMD_READ0, + NAND_CMD_READSTART, READ_PAGE_CMD_CODE); + vf610_nfc_addr_cycle(mtd, column, page); + break; + + case NAND_CMD_ERASE1: + if (nfc->page == page) + nfc->page = -1; + vf610_nfc_send_commands(nfc->regs, command, + NAND_CMD_ERASE2, ERASE_CMD_CODE); + vf610_nfc_addr_cycle(mtd, column, page); + break; + + case NAND_CMD_READID: + nfc->alt_buf = ALT_BUF_ID; + vf610_nfc_send_command(nfc->regs, command, READ_ID_CMD_CODE); + break; + + case NAND_CMD_STATUS: + nfc->alt_buf = ALT_BUF_STAT; + vf610_nfc_send_command(nfc->regs, command, + STATUS_READ_CMD_CODE); + break; + default: + return; + } + + vf610_nfc_done(mtd); +} + +static inline void vf610_nfc_read_spare(struct mtd_info *mtd, void *buf, + int len) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + + len = min(mtd->oobsize, (uint)len); + if (len > 0) + vf610_nfc_memcpy(buf, nfc->regs + mtd->writesize, len); +} + +/* Read data from NFC buffers */ +static void vf610_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + uint c = nfc->column; + uint l; + + /* Handle main area */ + if (!nfc->spareonly) { + l = min((uint)len, mtd->writesize - c); + nfc->column += l; + + if (!nfc->alt_buf) + vf610_nfc_memcpy(buf, nfc->regs + NFC_MAIN_AREA(0) + c, + l); + else + if (nfc->alt_buf & ALT_BUF_ID) + *buf = vf610_nfc_get_id(mtd, c); + else + *buf = vf610_nfc_get_status(mtd); + + buf += l; + len -= l; + } + + /* Handle spare area access */ + if (len) { + nfc->column += len; + vf610_nfc_read_spare(mtd, buf, len); + } +} + +/* Write data to NFC buffers */ +static void vf610_nfc_write_buf(struct mtd_info *mtd, const u_char *buf, + int len) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + uint c = nfc->column; + uint l; + + l = min((uint)len, mtd->writesize + mtd->oobsize - c); + nfc->column += l; + vf610_nfc_memcpy(nfc->regs + NFC_MAIN_AREA(0) + c, buf, l); +} + +/* Read byte from NFC buffers */ +static u8 vf610_nfc_read_byte(struct mtd_info *mtd) +{ + u8 tmp; + vf610_nfc_read_buf(mtd, &tmp, sizeof(tmp)); + return tmp; +} + +/* Read word from NFC buffers */ +static u16 vf610_nfc_read_word(struct mtd_info *mtd) +{ + u16 tmp; + vf610_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp)); + return tmp; +} + +/* If not provided, upper layers apply a fixed delay. */ +static int vf610_nfc_dev_ready(struct mtd_info *mtd) +{ + /* NFC handles R/B internally; always ready. */ + return 1; +} + +/* + * This function supports Vybrid only (MPC5125 would have full RB and four CS) + */ +static void vf610_nfc_select_chip(struct mtd_info *mtd, int chip) +{ +#ifdef CONFIG_VF610 + u32 tmp = vf610_nfc_read(mtd, NFC_ROW_ADDR); + tmp &= ~(ROW_ADDR_CHIP_SEL_RB_MASK | ROW_ADDR_CHIP_SEL_MASK); + tmp |= 1 << ROW_ADDR_CHIP_SEL_RB_SHIFT; + + if (chip == 0) + tmp |= 1 << ROW_ADDR_CHIP_SEL_SHIFT; + else if (chip == 1) + tmp |= 2 << ROW_ADDR_CHIP_SEL_SHIFT; + + vf610_nfc_write(mtd, NFC_ROW_ADDR, tmp); +#endif +} + +/* Count the number of 0's in buff upto max_bits */ +static inline int count_written_bits(uint8_t *buff, int size, int max_bits) +{ + uint32_t *buff32 = (uint32_t *)buff; + int k, written_bits = 0; + + for (k = 0; k < (size / 4); k++) { + written_bits += hweight32(~buff32[k]); + if (written_bits > max_bits) + break; + } + + return written_bits; +} + +static inline int vf610_nfc_correct_data(struct mtd_info *mtd, u_char *dat) +{ + struct vf610_nfc *nfc = mtd_to_nfc(mtd); + u8 ecc_status; + u8 ecc_count; + int flip; + + ecc_status = __raw_readb(nfc->regs + ECC_SRAM_ADDR * 8 + ECC_OFFSET); + ecc_count = ecc_status & ECC_ERR_COUNT; + if (!(ecc_status & ECC_STATUS_MASK)) + return ecc_count; + + /* If 'ecc_count' zero or less then buffer is all 0xff or erased. */ + flip = count_written_bits(dat, nfc->chip.ecc.size, ecc_count); + + /* ECC failed. */ + if (flip > ecc_count) { + nfc->page = -1; + return -1; + } + + /* Erased page. */ + memset(dat, 0xff, nfc->chip.ecc.size); + return 0; +} + + +static int vf610_nfc_read_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page) +{ + int eccsize = chip->ecc.size; + int stat; + uint8_t *p = buf; + + + vf610_nfc_read_buf(mtd, p, eccsize); + + if (oob_required) + vf610_nfc_read_buf(mtd, chip->oob_poi, mtd->oobsize); + + stat = vf610_nfc_correct_data(mtd, p); + + if (stat < 0) + mtd->ecc_stats.failed++; + else + mtd->ecc_stats.corrected += stat; + + return 0; +} + +/* + * ECC will be calculated automatically + */ +static int vf610_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required) +{ + vf610_nfc_write_buf(mtd, buf, mtd->writesize); + if (oob_required) + vf610_nfc_write_buf(mtd, chip->oob_poi, mtd->oobsize); + + return 0; +} + +struct vf610_nfc_config { + int hardware_ecc; + int width; + int flash_bbt; +}; + +static int vf610_nfc_nand_init(int devnum, void __iomem *addr) +{ + struct mtd_info *mtd = &nand_info[devnum]; + struct nand_chip *chip; + struct vf610_nfc *nfc; + int err = 0; + int page_sz; + struct vf610_nfc_config cfg = { + .hardware_ecc = 1, +#ifdef CONFIG_SYS_NAND_BUSWIDTH_16BIT + .width = 16, +#else + .width = 8, +#endif + .flash_bbt = 1, + }; + + nfc = malloc(sizeof(*nfc)); + if (!nfc) { + printf(KERN_ERR "%s: Memory exhausted!\n", __func__); + return -ENOMEM; + } + + chip = &nfc->chip; + nfc->regs = addr; + + mtd->priv = chip; + chip->priv = nfc; + + if (cfg.width == 16) { + chip->options |= NAND_BUSWIDTH_16; + vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_16BIT); + } else { + chip->options &= ~NAND_BUSWIDTH_16; + vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_16BIT); + } + + chip->dev_ready = vf610_nfc_dev_ready; + chip->cmdfunc = vf610_nfc_command; + chip->read_byte = vf610_nfc_read_byte; + chip->read_word = vf610_nfc_read_word; + chip->read_buf = vf610_nfc_read_buf; + chip->write_buf = vf610_nfc_write_buf; + chip->select_chip = vf610_nfc_select_chip; + + /* Bad block options. */ + if (cfg.flash_bbt) + chip->bbt_options = NAND_BBT_USE_FLASH | NAND_BBT_CREATE; + + /* Default to software ECC until flash ID. */ + vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG, + CONFIG_ECC_MODE_MASK, + CONFIG_ECC_MODE_SHIFT, ECC_BYPASS); + + chip->bbt_td = &bbt_main_descr; + chip->bbt_md = &bbt_mirror_descr; + + page_sz = PAGE_2K + OOB_64; + page_sz += cfg.width == 16 ? 1 : 0; + vf610_nfc_write(mtd, NFC_SECTOR_SIZE, page_sz); + + /* Set configuration register. */ + vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_ADDR_AUTO_INCR_BIT); + vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_BUFNO_AUTO_INCR_BIT); + vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_BOOT_MODE_BIT); + vf610_nfc_clear(mtd, NFC_FLASH_CONFIG, CONFIG_DMA_REQ_BIT); + vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_FAST_FLASH_BIT); + + /* Enable Idle IRQ */ + vf610_nfc_set(mtd, NFC_IRQ_STATUS, IDLE_EN_BIT); + + /* PAGE_CNT = 1 */ + vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG, CONFIG_PAGE_CNT_MASK, + CONFIG_PAGE_CNT_SHIFT, 1); + + /* Set ECC_STATUS offset */ + vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG, + CONFIG_ECC_SRAM_ADDR_MASK, + CONFIG_ECC_SRAM_ADDR_SHIFT, ECC_SRAM_ADDR); + + /* first scan to find the device and get the page size */ + if (nand_scan_ident(mtd, CONFIG_SYS_MAX_NAND_DEVICE, NULL)) { + err = -ENXIO; + goto error; + } + + chip->ecc.mode = NAND_ECC_SOFT; /* default */ + + page_sz = mtd->writesize + mtd->oobsize; + + /* Single buffer only, max 256 OOB minus ECC status */ + if (page_sz > PAGE_2K + 256 - 8) { + dev_err(nfc->dev, "Unsupported flash size\n"); + err = -ENXIO; + goto error; + } + page_sz += cfg.width == 16 ? 1 : 0; + vf610_nfc_write(mtd, NFC_SECTOR_SIZE, page_sz); + + if (cfg.hardware_ecc) { + if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) { + dev_err(nfc->dev, "Unsupported flash with hwecc\n"); + err = -ENXIO; + goto error; + } + + chip->ecc.layout = &vf610_nfc_ecc45; + + /* propagate ecc.layout to mtd_info */ + mtd->ecclayout = chip->ecc.layout; + chip->ecc.read_page = vf610_nfc_read_page; + chip->ecc.write_page = vf610_nfc_write_page; + chip->ecc.mode = NAND_ECC_HW; + + chip->ecc.bytes = 45; + chip->ecc.size = PAGE_2K; + chip->ecc.strength = 24; + + /* set ECC mode to 45 bytes OOB with 24 bits correction */ + vf610_nfc_set_field(mtd, NFC_FLASH_CONFIG, + CONFIG_ECC_MODE_MASK, + CONFIG_ECC_MODE_SHIFT, ECC_45_BYTE); + + /* Enable ECC_STATUS */ + vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_ECC_SRAM_REQ_BIT); + } + + /* second phase scan */ + err = nand_scan_tail(mtd); + if (err) + return err; + + err = nand_register(devnum); + if (err) + return err; + + return 0; + +error: + return err; +} + +void board_nand_init(void) +{ + int err = vf610_nfc_nand_init(0, (void __iomem *)CONFIG_SYS_NAND_BASE); + if (err) + printf("VF610 NAND init failed (err %d)\n", err); +} -- cgit v1.3.1 From dd24b57bb78422eba6780f0b6cc4c0b049a82371 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Mon, 28 Apr 2014 03:38:39 +0200 Subject: usb: ehci: mxs: Add board-specific callbacks Add board-specific callbacks for enabling/disabling port power into the MXS EHCI controller driver. This is in-line with the names of callbacks on other systems. Signed-off-by: Marek Vasut Cc: Stefano Babic --- drivers/usb/host/ehci-mxs.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'drivers') diff --git a/drivers/usb/host/ehci-mxs.c b/drivers/usb/host/ehci-mxs.c index 4d652b32dbe..6b8d969bb00 100644 --- a/drivers/usb/host/ehci-mxs.c +++ b/drivers/usb/host/ehci-mxs.c @@ -77,6 +77,16 @@ static int ehci_mxs_toggle_clock(const struct ehci_mxs_port *port, int enable) return 0; } +int __weak board_ehci_hcd_init(int port) +{ + return 0; +} + +int __weak board_ehci_hcd_exit(int port) +{ + return 0; +} + int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { @@ -90,6 +100,10 @@ int ehci_hcd_init(int index, enum usb_init_type init, return -EINVAL; } + ret = board_ehci_hcd_init(index); + if (ret) + return ret; + port = &mxs_port[index]; /* Reset the PHY block */ @@ -154,5 +168,7 @@ int ehci_hcd_stop(int index) /* Disable USB clock */ ret = ehci_mxs_toggle_clock(port, 0); + board_ehci_hcd_exit(index); + return ret; } -- cgit v1.3.1 From 5546ad0734bb5eed2b3cd6333dbcec51ae45185a Mon Sep 17 00:00:00 2001 From: "Ye.Li" Date: Mon, 15 Sep 2014 17:23:14 +0800 Subject: usb: ehci-mx6: Rename the USB register base address The mx6sl/mx6sx has 2 OTG and 1 host. So they have name "USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes the USB base address name to "USBOH3", which causes the driver failed to build for mx6sl/mx6sx. This patch uniform the address name to "USB_BASE_ADDR" for all mx6 series. Signed-off-by: Ye.Li --- arch/arm/include/asm/arch-mx6/imx-regs.h | 9 ++------- drivers/usb/host/ehci-mx6.c | 4 ++-- 2 files changed, 4 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h b/arch/arm/include/asm/arch-mx6/imx-regs.h index 22614fcd0ec..a159309bb9f 100644 --- a/arch/arm/include/asm/arch-mx6/imx-regs.h +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h @@ -215,13 +215,8 @@ #define AIPS2_OFF_BASE_ADDR (ATZ2_BASE_ADDR + 0x80000) #define CAAM_BASE_ADDR (ATZ2_BASE_ADDR) #define ARM_BASE_ADDR (ATZ2_BASE_ADDR + 0x40000) -#ifdef CONFIG_MX6SL -#define USBO2H_PL301_IPS_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000) -#define USBO2H_USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000) -#else -#define USBOH3_PL301_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000) -#define USBOH3_USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000) -#endif +#define USB_PL301_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x0000) +#define USB_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x4000) #define ENET_BASE_ADDR (AIPS2_OFF_BASE_ADDR + 0x8000) #ifdef CONFIG_MX6SL diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index c0a557b2adc..9ec5a0a5394 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -174,7 +174,7 @@ struct usbnc_regs { static void usb_oc_config(int index) { - struct usbnc_regs *usbnc = (struct usbnc_regs *)(USBOH3_USB_BASE_ADDR + + struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET); void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]); u32 val; @@ -207,7 +207,7 @@ int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { enum usb_init_type type; - struct usb_ehci *ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR + + struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR + (0x200 * index)); if (index > 3) -- cgit v1.3.1 From 2c94611d5f6dc5b49c02806dfdaacf6b27a5da83 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Tue, 7 Oct 2014 22:01:40 -0600 Subject: cros_ec: power: Add a tunnelled version of the tps65090 driver Unfortunately on Pit the AP has no direct access to the tps65090 but must talk through the EC (over SPI) to the EC's I2C bus. When driver model supports PMICs this will be relatively easy. In the meantime the best approach is to duplicate the driver. It will be refactored once driver model support is expanded. Signed-off-by: Simon Glass Tested-by: Ajay Kumar Signed-off-by: Minkyu Kang --- drivers/power/pmic/Makefile | 1 + drivers/power/pmic/pmic_tps65090_ec.c | 218 ++++++++++++++++++++++++++++++++++ 2 files changed, 219 insertions(+) create mode 100644 drivers/power/pmic/pmic_tps65090_ec.c (limited to 'drivers') diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile index a472f61f88f..0b766112c01 100644 --- a/drivers/power/pmic/Makefile +++ b/drivers/power/pmic/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_POWER_MUIC_MAX8997) += muic_max8997.o obj-$(CONFIG_POWER_MAX77686) += pmic_max77686.o obj-$(CONFIG_POWER_PFUZE100) += pmic_pfuze100.o obj-$(CONFIG_POWER_TPS65090) += pmic_tps65090.o +obj-$(CONFIG_POWER_TPS65090_EC) += pmic_tps65090_ec.o obj-$(CONFIG_POWER_TPS65217) += pmic_tps65217.o obj-$(CONFIG_POWER_TPS65218) += pmic_tps65218.o obj-$(CONFIG_POWER_TPS65910) += pmic_tps65910.o diff --git a/drivers/power/pmic/pmic_tps65090_ec.c b/drivers/power/pmic/pmic_tps65090_ec.c new file mode 100644 index 00000000000..ac0d44fec83 --- /dev/null +++ b/drivers/power/pmic/pmic_tps65090_ec.c @@ -0,0 +1,218 @@ +/* + * Copyright (c) 2013 The Chromium OS Authors. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define TPS65090_ADDR 0x48 + +static struct tps65090 { + struct cros_ec_dev *dev; /* The CROS_EC device */ +} config; + +/* TPS65090 register addresses */ +enum { + REG_IRQ1 = 0, + REG_CG_CTRL0 = 4, + REG_CG_STATUS1 = 0xa, + REG_FET1_CTRL = 0x0f, + REG_FET2_CTRL, + REG_FET3_CTRL, + REG_FET4_CTRL, + REG_FET5_CTRL, + REG_FET6_CTRL, + REG_FET7_CTRL, + TPS65090_NUM_REGS, +}; + +enum { + IRQ1_VBATG = 1 << 3, + CG_CTRL0_ENC_MASK = 0x01, + + MAX_FET_NUM = 7, + MAX_CTRL_READ_TRIES = 5, + + /* TPS65090 FET_CTRL register values */ + FET_CTRL_TOFET = 1 << 7, /* Timeout, startup, overload */ + FET_CTRL_PGFET = 1 << 4, /* Power good for FET status */ + FET_CTRL_WAIT = 3 << 2, /* Overcurrent timeout max */ + FET_CTRL_ADENFET = 1 << 1, /* Enable output auto discharge */ + FET_CTRL_ENFET = 1 << 0, /* Enable FET */ +}; + +/** + * tps65090_read - read a byte from tps6090 + * + * @param reg The register address to read from. + * @param val We'll return value value read here. + * @return 0 if ok; error if EC returns failure. + */ +static int tps65090_read(u32 reg, u8 *val) +{ + return cros_ec_i2c_xfer(config.dev, TPS65090_ADDR, reg, 1, + val, 1, true); +} + +/** + * tps65090_write - write a byte to tps6090 + * + * @param reg The register address to write to. + * @param val The value to write. + * @return 0 if ok; error if EC returns failure. + */ +static int tps65090_write(u32 reg, u8 val) +{ + return cros_ec_i2c_xfer(config.dev, TPS65090_ADDR, reg, 1, + &val, 1, false); +} + +/** + * Checks for a valid FET number + * + * @param fet_id FET number to check + * @return 0 if ok, -EINVAL if FET value is out of range + */ +static int tps65090_check_fet(unsigned int fet_id) +{ + if (fet_id == 0 || fet_id > MAX_FET_NUM) { + debug("parameter fet_id is out of range, %u not in 1 ~ %u\n", + fet_id, MAX_FET_NUM); + return -EINVAL; + } + + return 0; +} + +/** + * Set the power state for a FET + * + * @param fet_id Fet number to set (1..MAX_FET_NUM) + * @param set 1 to power on FET, 0 to power off + * @return -EIO if we got a comms error, -EAGAIN if the FET failed to + * change state. If all is ok, returns 0. + */ +static int tps65090_fet_set(int fet_id, bool set) +{ + int retry; + u8 reg, value; + + value = FET_CTRL_ADENFET | FET_CTRL_WAIT; + if (set) + value |= FET_CTRL_ENFET; + + if (tps65090_write(REG_FET1_CTRL + fet_id - 1, value)) + return -EIO; + + /* Try reading until we get a result */ + for (retry = 0; retry < MAX_CTRL_READ_TRIES; retry++) { + if (tps65090_read(REG_FET1_CTRL + fet_id - 1, ®)) + return -EIO; + + /* Check that the fet went into the expected state */ + if (!!(reg & FET_CTRL_PGFET) == set) + return 0; + + /* If we got a timeout, there is no point in waiting longer */ + if (reg & FET_CTRL_TOFET) + break; + + mdelay(1); + } + + debug("FET %d: Power good should have set to %d but reg=%#02x\n", + fet_id, set, reg); + return -EAGAIN; +} + +int tps65090_fet_enable(unsigned int fet_id) +{ + ulong start; + int loops; + int ret; + + ret = tps65090_check_fet(fet_id); + if (ret) + return ret; + + start = get_timer(0); + for (loops = 0;; loops++) { + ret = tps65090_fet_set(fet_id, true); + if (!ret) + break; + + if (get_timer(start) > 100) + break; + + /* Turn it off and try again until we time out */ + tps65090_fet_set(fet_id, false); + } + + if (ret) { + debug("%s: FET%d failed to power on: time=%lums, loops=%d\n", + __func__, fet_id, get_timer(start), loops); + } else if (loops) { + debug("%s: FET%d powered on after %lums, loops=%d\n", + __func__, fet_id, get_timer(start), loops); + } + /* + * Unfortunately, there are some conditions where the power + * good bit will be 0, but the fet still comes up. One such + * case occurs with the lcd backlight. We'll just return 0 here + * and assume that the fet will eventually come up. + */ + if (ret == -EAGAIN) + ret = 0; + + return ret; +} + +int tps65090_fet_disable(unsigned int fet_id) +{ + int ret; + + ret = tps65090_check_fet(fet_id); + if (ret) + return ret; + + ret = tps65090_fet_set(fet_id, false); + + return ret; +} + +int tps65090_fet_is_enabled(unsigned int fet_id) +{ + u8 reg = 0; + int ret; + + ret = tps65090_check_fet(fet_id); + if (ret) + return ret; + ret = tps65090_read(REG_FET1_CTRL + fet_id - 1, ®); + if (ret) { + debug("fail to read FET%u_CTRL register over I2C", fet_id); + return -EIO; + } + + return reg & FET_CTRL_ENFET; +} + +int tps65090_init(void) +{ + puts("TPS65090 PMIC EC init\n"); + + config.dev = board_get_cros_ec_dev(); + if (!config.dev) { + debug("%s: no cros_ec device: cannot init tps65090\n", + __func__); + return -ENODEV; + } + + return 0; +} -- cgit v1.3.1 From 5b9c8cb6cbb822594b9e5171a7ee2839f497352e Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Tue, 7 Oct 2014 22:01:41 -0600 Subject: cros_ec: exynos: Use the correct tps65090 driver in each case Exynos 5250 boards (snow, spring) use the I2C driver but Exynos 5420 boards cannot due to a hardware design decision. Select the correct driver to use in each case. Signed-off-by: Simon Glass Tested-by: Ajay Kumar Signed-off-by: Minkyu Kang --- drivers/power/pmic/Makefile | 2 +- include/configs/exynos5250-dt.h | 1 + include/configs/peach-pit.h | 2 ++ 3 files changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile index 0b766112c01..e7b07ebab49 100644 --- a/drivers/power/pmic/Makefile +++ b/drivers/power/pmic/Makefile @@ -11,7 +11,7 @@ obj-$(CONFIG_POWER_MAX8997) += pmic_max8997.o obj-$(CONFIG_POWER_MUIC_MAX8997) += muic_max8997.o obj-$(CONFIG_POWER_MAX77686) += pmic_max77686.o obj-$(CONFIG_POWER_PFUZE100) += pmic_pfuze100.o -obj-$(CONFIG_POWER_TPS65090) += pmic_tps65090.o +obj-$(CONFIG_POWER_TPS65090_I2C) += pmic_tps65090.o obj-$(CONFIG_POWER_TPS65090_EC) += pmic_tps65090_ec.o obj-$(CONFIG_POWER_TPS65217) += pmic_tps65217.o obj-$(CONFIG_POWER_TPS65218) += pmic_tps65218.o diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h index c24984bd2b9..5504515ab1f 100644 --- a/include/configs/exynos5250-dt.h +++ b/include/configs/exynos5250-dt.h @@ -42,6 +42,7 @@ /* PMIC */ #define CONFIG_POWER_MAX77686 +#define CONFIG_POWER_TPS65090_I2C /* Sound */ #define CONFIG_CMD_SOUND diff --git a/include/configs/peach-pit.h b/include/configs/peach-pit.h index 987cef504c9..34734ada21c 100644 --- a/include/configs/peach-pit.h +++ b/include/configs/peach-pit.h @@ -30,4 +30,6 @@ #define LCD_BPP LCD_COLOR16 #endif +#define CONFIG_POWER_TPS65090_EC + #endif /* __CONFIG_PEACH_PIT_H */ -- cgit v1.3.1 From 311757be275c1d592ff357e9faedca4c967a3064 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Tue, 7 Oct 2014 22:01:50 -0600 Subject: samsung: Enable device tree for s5p_goni Change this board to add a device tree. This also adds a pinmux header file although it is not used as yet. Signed-off-by: Simon Glass Signed-off-by: Minkyu Kang --- arch/arm/Kconfig | 9 +++-- arch/arm/cpu/armv7/s5pc1xx/Kconfig | 20 ++++++++++ arch/arm/dts/Makefile | 1 + arch/arm/dts/s5pc1xx-goni.dts | 28 ++++++++++++++ arch/arm/include/asm/arch-s5pc1xx/periph.h | 61 ++++++++++++++++++++++++++++++ arch/arm/include/asm/arch-s5pc1xx/pinmux.h | 50 ++++++++++++++++++++++++ configs/s5p_goni_defconfig | 2 + drivers/mmc/s5p_sdhci.c | 2 - include/configs/s5p_goni.h | 4 +- 9 files changed, 170 insertions(+), 7 deletions(-) create mode 100644 arch/arm/cpu/armv7/s5pc1xx/Kconfig create mode 100644 arch/arm/dts/s5pc1xx-goni.dts create mode 100644 arch/arm/include/asm/arch-s5pc1xx/periph.h create mode 100644 arch/arm/include/asm/arch-s5pc1xx/pinmux.h (limited to 'drivers') diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 43ba33a2af5..22ceb9dbb96 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -336,6 +336,9 @@ config TARGET_BCM958622HR config ARCH_EXYNOS bool "Samsung EXYNOS" +config ARCH_S5PC1XX + bool "Samsung S5PC1XX" + config ARCH_HIGHBANK bool "Calxeda Highbank" @@ -429,9 +432,6 @@ config RMOBILE config TARGET_CM_FX6 bool "Support cm_fx6" -config TARGET_S5P_GONI - bool "Support s5p_goni" - config TARGET_SMDKC100 bool "Support smdkc100" @@ -550,6 +550,8 @@ source "arch/arm/cpu/arm926ejs/orion5x/Kconfig" source "arch/arm/cpu/armv7/rmobile/Kconfig" +source "arch/arm/cpu/armv7/s5pc1xx/Kconfig" + source "arch/arm/cpu/armv7/tegra-common/Kconfig" source "arch/arm/cpu/armv7/uniphier/Kconfig" @@ -657,7 +659,6 @@ source "board/raspberrypi/rpi_b/Kconfig" source "board/ronetix/pm9261/Kconfig" source "board/ronetix/pm9263/Kconfig" source "board/ronetix/pm9g45/Kconfig" -source "board/samsung/goni/Kconfig" source "board/samsung/smdk2410/Kconfig" source "board/samsung/smdkc100/Kconfig" source "board/sandisk/sansa_fuze_plus/Kconfig" diff --git a/arch/arm/cpu/armv7/s5pc1xx/Kconfig b/arch/arm/cpu/armv7/s5pc1xx/Kconfig new file mode 100644 index 00000000000..1a8941dd9aa --- /dev/null +++ b/arch/arm/cpu/armv7/s5pc1xx/Kconfig @@ -0,0 +1,20 @@ +if ARCH_S5PC1XX + +choice + prompt "S5PC1XX board select" + +config TARGET_S5P_GONI + bool "S5P Goni board" + select OF_CONTROL if !SPL_BUILD + +endchoice + +config SYS_CPU + default "armv7" + +config SYS_SOC + default "s5pc1xx" + +source "board/samsung/goni/Kconfig" + +endif diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 43a70e455f6..076e0f7bf28 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1,3 +1,4 @@ +dtb-$(CONFIG_S5PC110) += s5pc1xx-goni.dtb dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ exynos4210-universal_c210.dtb \ diff --git a/arch/arm/dts/s5pc1xx-goni.dts b/arch/arm/dts/s5pc1xx-goni.dts new file mode 100644 index 00000000000..2e671bbf7e9 --- /dev/null +++ b/arch/arm/dts/s5pc1xx-goni.dts @@ -0,0 +1,28 @@ +/* + * Samsung's S5PC110-based Goni board device tree source + * + * Copyright (c) 2014 Google, Inc + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; + +#include "skeleton.dtsi" + +/ { + model = "Samsung Goni based on S5PC110"; + compatible = "samsung,goni", "samsung,s5pc110"; + + aliases { + serial2 = "/serial@e2900800"; + console = "/serial@e2900800"; + }; + + serial@e2900800 { + compatible = "samsung,exynos4210-uart"; + reg = <0xe2900800 0x400>; + id = <2>; + }; + +}; diff --git a/arch/arm/include/asm/arch-s5pc1xx/periph.h b/arch/arm/include/asm/arch-s5pc1xx/periph.h new file mode 100644 index 00000000000..5c1c3d4a93c --- /dev/null +++ b/arch/arm/include/asm/arch-s5pc1xx/periph.h @@ -0,0 +1,61 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Rajeshwari Shinde + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ASM_ARM_ARCH_PERIPH_H +#define __ASM_ARM_ARCH_PERIPH_H + +/* + * Peripherals required for pinmux configuration. List will + * grow with support for more devices getting added. + * Numbering based on interrupt table. + * + */ +enum periph_id { + PERIPH_ID_UART0 = 51, + PERIPH_ID_UART1, + PERIPH_ID_UART2, + PERIPH_ID_UART3, + PERIPH_ID_I2C0 = 56, + PERIPH_ID_I2C1, + PERIPH_ID_I2C2, + PERIPH_ID_I2C3, + PERIPH_ID_I2C4, + PERIPH_ID_I2C5, + PERIPH_ID_I2C6, + PERIPH_ID_I2C7, + PERIPH_ID_SPI0 = 68, + PERIPH_ID_SPI1, + PERIPH_ID_SPI2, + PERIPH_ID_SDMMC0 = 75, + PERIPH_ID_SDMMC1, + PERIPH_ID_SDMMC2, + PERIPH_ID_SDMMC3, + PERIPH_ID_I2C8 = 87, + PERIPH_ID_I2C9, + PERIPH_ID_I2S0 = 98, + PERIPH_ID_I2S1 = 99, + + /* Since following peripherals do + * not have shared peripheral interrupts (SPIs) + * they are numbered arbitiraly after the maximum + * SPIs Exynos has (128) + */ + PERIPH_ID_SROMC = 128, + PERIPH_ID_SPI3, + PERIPH_ID_SPI4, + PERIPH_ID_SDMMC4, + PERIPH_ID_PWM0, + PERIPH_ID_PWM1, + PERIPH_ID_PWM2, + PERIPH_ID_PWM3, + PERIPH_ID_PWM4, + PERIPH_ID_I2C10 = 203, + + PERIPH_ID_NONE = -1, +}; + +#endif /* __ASM_ARM_ARCH_PERIPH_H */ diff --git a/arch/arm/include/asm/arch-s5pc1xx/pinmux.h b/arch/arm/include/asm/arch-s5pc1xx/pinmux.h new file mode 100644 index 00000000000..0b91ef658ca --- /dev/null +++ b/arch/arm/include/asm/arch-s5pc1xx/pinmux.h @@ -0,0 +1,50 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Abhilash Kesavan + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __ASM_ARM_ARCH_PINMUX_H +#define __ASM_ARM_ARCH_PINMUX_H + +#include "periph.h" + +/* + * Flags for setting specific configarations of peripherals. + * List will grow with support for more devices getting added. + */ +enum { + PINMUX_FLAG_NONE = 0x00000000, + + /* Flags for eMMC */ + PINMUX_FLAG_8BIT_MODE = 1 << 0, /* SDMMC 8-bit mode */ + + /* Flags for SROM controller */ + PINMUX_FLAG_BANK = 3 << 0, /* bank number (0-3) */ + PINMUX_FLAG_16BIT = 1 << 2, /* 16-bit width */ +}; + +/** + * Configures the pinmux for a particular peripheral. + * + * Each gpio can be configured in many different ways (4 bits on exynos) + * such as "input", "output", "special function", "external interrupt" + * etc. This function will configure the peripheral pinmux along with + * pull-up/down and drive strength. + * + * @param peripheral peripheral to be configured + * @param flags configure flags + * @return 0 if ok, -1 on error (e.g. unsupported peripheral) + */ +int exynos_pinmux_config(int peripheral, int flags); + +/** + * Decode the peripheral id using the interrpt numbers. + * + * @param blob Device tree blob + * @param node FDT I2C node to find + * @return peripheral id if ok, PERIPH_ID_NONE on error + */ +int pinmux_decode_periph_id(const void *blob, int node); +#endif diff --git a/configs/s5p_goni_defconfig b/configs/s5p_goni_defconfig index c0c35090cf9..618e5908025 100644 --- a/configs/s5p_goni_defconfig +++ b/configs/s5p_goni_defconfig @@ -1,2 +1,4 @@ CONFIG_ARM=y +CONFIG_ARCH_S5PC1XX=y CONFIG_TARGET_S5P_GONI=y +CONFIG_DEFAULT_DEVICE_TREE="s5pc1xx-goni" diff --git a/drivers/mmc/s5p_sdhci.c b/drivers/mmc/s5p_sdhci.c index 2ff0ec2a422..637dd972a5b 100644 --- a/drivers/mmc/s5p_sdhci.c +++ b/drivers/mmc/s5p_sdhci.c @@ -14,9 +14,7 @@ #include #include #include -#ifdef CONFIG_OF_CONTROL #include -#endif static char *S5P_NAME = "SAMSUNG SDHCI"; static void s5p_sdhci_set_control_reg(struct sdhci_host *host) diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index a51215d9ae1..feb4d7670b6 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -53,6 +53,7 @@ #define CONFIG_MMC #define CONFIG_SDHCI #define CONFIG_S5P_SDHCI +#define SDHCI_MAX_HOSTS 4 /* PWM */ #define CONFIG_PWM 1 @@ -106,7 +107,6 @@ ",12m(modem)"\ ",60m(qboot)\0" -#define CONFIG_BOOTDELAY 1 #define CONFIG_ZERO_BOOTDELAY_CHECK /* partitions definitions */ @@ -283,4 +283,6 @@ #define CONFIG_CMD_USB_MASS_STORAGE #define CONFIG_USB_GADGET_MASS_STORAGE +#define CONFIG_OF_LIBFDT + #endif /* __CONFIG_H */ -- cgit v1.3.1 From 476095772f3aa58ee581943e4e993d9b8a61239c Mon Sep 17 00:00:00 2001 From: Andreas Bießmann Date: Thu, 18 Sep 2014 23:46:48 +0200 Subject: macb: simplify gmac initialisation MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Signed-off-by: Andreas Bießmann Cc: Joe Hershberger Cc: Bo Shen --- drivers/net/macb.c | 25 ++++++++----------------- 1 file changed, 8 insertions(+), 17 deletions(-) (limited to 'drivers') diff --git a/drivers/net/macb.c b/drivers/net/macb.c index 01a94a4c4d1..375c8a4454a 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -479,31 +479,22 @@ static int macb_phy_init(struct macb_device *macb) /* First check for GMAC */ if (macb_is_gem(macb)) { lpa = macb_mdio_read(macb, MII_STAT1000); - if (lpa & (1 << 11)) { - speed = 1000; - duplex = 1; - } else { - if (lpa & (1 << 10)) { - speed = 1000; - duplex = 1; - } else { - speed = 0; - } - } - if (speed == 1000) { - printf("%s: link up, %dMbps %s-duplex (lpa: 0x%04x)\n", + if (lpa & (LPA_1000FULL | LPA_1000HALF)) { + duplex = ((lpa & LPA_1000FULL) ? 1 : 0); + + printf("%s: link up, 1000Mbps %s-duplex (lpa: 0x%04x)\n", netdev->name, - speed, duplex ? "full" : "half", lpa); ncfgr = macb_readl(macb, NCFGR); - ncfgr &= ~(GEM_BIT(GBE) | MACB_BIT(SPD) | MACB_BIT(FD)); - if (speed) - ncfgr |= GEM_BIT(GBE); + ncfgr &= ~(MACB_BIT(SPD) | MACB_BIT(FD)); + ncfgr |= GEM_BIT(GBE); + if (duplex) ncfgr |= MACB_BIT(FD); + macb_writel(macb, NCFGR, ncfgr); return 1; -- cgit v1.3.1