From dae6c6ba95f61326e8012c2fec372a6735ba46b9 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Tue, 3 Dec 2013 12:17:34 +0530 Subject: include/mmc.h: Remove declaration for spl_mmc_load() The spl_mmc_load() was removed while converting to CONFIG_SPL_FRAMEWORK usage the definition was removed but the declaration was missed. This patch removes this declaration. Signed-off-by: Lad, Prabhakar Acked-by: Pantelis Antoniou --- include/mmc.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include/mmc.h') diff --git a/include/mmc.h b/include/mmc.h index cb558da63d8..8f51c939d66 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -304,7 +304,6 @@ int board_mmc_getcd(struct mmc *mmc); int mmc_switch_part(int dev_num, unsigned int part_num); int mmc_getcd(struct mmc *mmc); int mmc_getwp(struct mmc *mmc); -void spl_mmc_load(void) __noreturn; /* Function to change the size of boot partition and rpmb partitions */ int mmc_boot_partition_size_change(struct mmc *mmc, unsigned long bootsize, unsigned long rpmbsize); -- cgit v1.2.3 From ab71188ce87ebb66192a5bdbbb9d58052bd32d93 Mon Sep 17 00:00:00 2001 From: Markus Niebel Date: Mon, 16 Dec 2013 13:40:46 +0100 Subject: mmc: add setdsr support The eMMC and the SD-Card specifications describe the optional SET_DSR command. During measurements at our lab we found that some cards implementing this feature having really strong driver strengts per default. This can lead to voltage peaks above the specification of the host on signal edges for data sent from a card to the host. Since availability of a given card type may be shorter than the time a certain hardware will be produced it is useful to have support for this command (Alternative would be changing termination resistors and adapting the driver strength of the host to the used card.) Following proposal for an implementation: - new field that reflects CSD field DSR_IMP in struct mmc - new field for design specific DSR value in struct mmc - board code can set DSR value in mmc struct just after registering an controller - mmc_startup sends the the stored DSR value before selecting a card, if DSR_IMP is set Additionally the mmc command is extended to make is possible to play around with different DSR values. The concept was tested on a i.MX53 based platform using a Micron eMMC card where the default DSR is 0x0400 (12mA) but in our design 0x0100 (0x0100) were enough. To use this feature for instance on a mx53loco one have to add a call to mmc_set_dsr() in board_mmc_init() after calling fsl_esdhc_initialize() for the eMMC. Signed-off-by: Markus Niebel Acked-by: Pantelis Antoniou --- include/mmc.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include/mmc.h') diff --git a/include/mmc.h b/include/mmc.h index 8f51c939d66..e1060b9ff27 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -262,6 +262,8 @@ struct mmc { uint card_caps; uint host_caps; uint ocr; + uint dsr; + uint dsr_imp; uint scr[2]; uint csd[4]; uint cid[4]; @@ -304,6 +306,7 @@ int board_mmc_getcd(struct mmc *mmc); int mmc_switch_part(int dev_num, unsigned int part_num); int mmc_getcd(struct mmc *mmc); int mmc_getwp(struct mmc *mmc); +int mmc_set_dsr(struct mmc *mmc, u16 val); /* Function to change the size of boot partition and rpmb partitions */ int mmc_boot_partition_size_change(struct mmc *mmc, unsigned long bootsize, unsigned long rpmbsize); -- cgit v1.2.3