From 491f6c2f291657dce8b67d85c15aaa9c03766b8e Mon Sep 17 00:00:00 2001 From: Albert ARIBAUD Date: Thu, 16 Aug 2012 06:35:21 +0000 Subject: edminiv2: orion5x: fix GPIO inits and values Orion5x did not actually write GPIO output values or input polarities, and ED Mini V2 had bad or missing values for GPIO settings. Signed-off-by: Albert ARIBAUD Acked-By: Prafulla Wadaskar --- include/configs/edminiv2.h | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h index f0fb48828ae..f2cfaf8350e 100644 --- a/include/configs/edminiv2.h +++ b/include/configs/edminiv2.h @@ -69,13 +69,18 @@ * - GPIO16 is Power LED control (0 = on, 1 = off) * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16) * - GPIO18 is Power Button status (0 = Released, 1 = Pressed) - * - Last GPIO is 26, further bits are supposed to be 0. + * - GPIO19 is SATA disk power toggle (toggles on 0-to-1) + * - GPIO22 is SATA disk power status () + * - GPIO23 is supply status for SATA disk () + * - GPIO24 is supply control for board (write 1 to power off) + * Last GPIO is 25, further bits are supposed to be 0. * Enable mask has ones for INPUT, 0 for OUTPUT. - * Default is LED ON. + * Default is LED ON, board ON :) */ -#define ORION5X_GPIO_OUT_ENABLE 0x03fcffff -#define ORION5X_GPIO_OUT_VALUE 0x03fcffff +#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca +#define ORION5X_GPIO_OUT_VALUE 0x00000000 +#define ORION5X_GPIO_IN_POLARITY 0x000000d0 /* * NS16550 Configuration -- cgit v1.3.1 From f46b4a1aadb4ab834bcf333a9dd4c7804296e185 Mon Sep 17 00:00:00 2001 From: Valentin Longchamp Date: Tue, 14 Aug 2012 01:39:10 +0000 Subject: km/arm: set SPI NOR Flash default parameters These parameters are used by the the sf probe command that are used by our update script and they therefore need to be set for all of our boards. The timing is the same as for the ENV SPI NOR Flash (since it's the same physical device) and takes the boco2 delay on the bus into account. Signed-off-by: Valentin Longchamp cc: Holger Brunck Acked-by: Prafulla Wadaskar --- include/configs/km/km_arm.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include') diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 27b77d3dabe..b41ca2e36d8 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -57,6 +57,10 @@ #define CONFIG_CMD_SF #define CONFIG_SOFT_I2C /* I2C bit-banged */ +/* SPI NOR Flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 8100000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 + #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 -- cgit v1.3.1 From 05c8e81fd39c8a41c2038844868a491003bcdab8 Mon Sep 17 00:00:00 2001 From: Valentin Longchamp Date: Tue, 14 Aug 2012 01:37:11 +0000 Subject: arm/km: fix frequency of the SPI NOR Flash According to our last HW measures, this could be raised while still compatible with the potential delays on the lines. Signed-off-by: Valentin Longchamp cc: Holger Brunck Acked-By: Prafulla Wadaskar --- include/configs/km/km_arm.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index b41ca2e36d8..44d5373968c 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -64,7 +64,7 @@ #if defined CONFIG_KM_ENV_IS_IN_SPI_NOR #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 5000000 +#define CONFIG_ENV_SPI_MAX_HZ 8100000 #define CONFIG_ENV_SPI_MODE SPI_MODE_3 #endif -- cgit v1.3.1 From fcca7e7acc56fc39fedb6a080e6b92aeff647dac Mon Sep 17 00:00:00 2001 From: Holger Brunck Date: Thu, 9 Aug 2012 01:37:47 +0000 Subject: arm/km: remove unused code For some reasons we had an own implementaion of dram_init and dram_init_banksize. This is not needed anymore, use the standard kirkwood functions instead. Signed-off-by: Holger Brunck cc: Prafulla Wadaskar cc: Valentin Longchamp cc: Gerlando Falauto Acked-By: Prafulla Wadaskar --- board/keymile/km_arm/km_arm.c | 20 -------------------- include/configs/km/keymile-common.h | 1 - 2 files changed, 21 deletions(-) (limited to 'include') diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index 930c80e7c2a..be8f51c2fc4 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -331,26 +331,6 @@ void board_spi_release_bus(struct spi_slave *slave) kw_gpio_set_value(KM_FLASH_GPIO_PIN, 1); } -int dram_init(void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - /* Fix this */ - gd->ram_size = get_ram_size((void *)kw_sdram_bar(0), - kw_sdram_bs(0)); - return 0; -} - -void dram_init_banksize(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i), - kw_sdram_bs(i)); - } -} - #if (defined(CONFIG_KM_PIGGY4_88E6061)) #define PHY_LED_SEL_REG 0x18 diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h index 7ed99587a24..99831047327 100644 --- a/include/configs/km/keymile-common.h +++ b/include/configs/km/keymile-common.h @@ -81,7 +81,6 @@ #define CONFIG_LOADS_ECHO #define CONFIG_SYS_LOADS_BAUD_CHANGE -#define CONFIG_SYS_BOARD_DRAM_INIT /* Used board specific dram_init */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS 1 -- cgit v1.3.1 From de6dc4ea3973b1308cf013a60d6a594232c10e88 Mon Sep 17 00:00:00 2001 From: Otavio Salvador Date: Mon, 27 Aug 2012 23:56:41 +0000 Subject: MX28: mx28evk: Enable SPI DMA Signed-off-by: Otavio Salvador --- include/configs/mx28evk.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index 4e1e6bc0a85..e34fd961174 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -199,6 +199,7 @@ #ifdef CONFIG_CMD_SPI #define CONFIG_HARD_SPI #define CONFIG_MXS_SPI +#define CONFIG_MXS_SPI_DMA_ENABLE #define CONFIG_SPI_HALF_DUPLEX #define CONFIG_DEFAULT_SPI_BUS 2 #define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0 -- cgit v1.3.1 From c16ecb09088f303cb36fd3c55108857cdf934b98 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Aug 2012 15:12:48 +0000 Subject: M28: Fix the use of gpmi-nand in mtdparts The mtd name of the NAND in Linux is "gpmi-nand", not "gpmi-nand.0" as it would be expected, since the controller doesn't support multiple NANDs attached to it as of now. Rectify this flub by adjusting default mtdparts. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Stefano Babic Cc: Otavio Salvador Acked-by: Stefano Babic --- include/configs/m28evk.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index d0f2b481d51..9eb2a547fc4 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -171,9 +171,9 @@ #define CONFIG_LZO #define CONFIG_MTD_DEVICE #define CONFIG_MTD_PARTITIONS -#define MTDIDS_DEFAULT "nand0=gpmi-nand.0" +#define MTDIDS_DEFAULT "nand0=gpmi-nand" #define MTDPARTS_DEFAULT \ - "mtdparts=gpmi-nand.0:" \ + "mtdparts=gpmi-nand:" \ "3m(bootloader)ro," \ "512k(environment)," \ "512k(redundant-environment)," \ -- cgit v1.3.1 From 91dd7ca6ac9b9b760a1671ec845d4401a13df11e Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 29 Aug 2012 06:20:03 +0000 Subject: mx28evk: Add USB Ethernet support Add USB Ethernet support. Signed-off-by: Fabio Estevam Reviewed-by: Marek Vasut --- include/configs/mx28evk.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include') diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index e34fd961174..43b40021d6a 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -184,6 +184,9 @@ #define CONFIG_EHCI_MXS_PORT 1 #define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_SMSC95XX #endif /* I2C */ -- cgit v1.3.1 From d812f4ad95d1f15c656c7f32d6077bc1224abf4a Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 30 Aug 2012 13:41:15 +0000 Subject: SCSPS1: Enable caches Enable caches, make it faster! Signed-off-by: Marek Vasut Cc: Stefano Babic Cc: Detlev Zundel --- include/configs/sc_sps_1.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include') diff --git a/include/configs/sc_sps_1.h b/include/configs/sc_sps_1.h index 0ebdfb8217d..f5dc3930209 100644 --- a/include/configs/sc_sps_1.h +++ b/include/configs/sc_sps_1.h @@ -39,8 +39,6 @@ #include #define CONFIG_SYS_NO_FLASH -#define CONFIG_SYS_ICACHE_OFF -#define CONFIG_SYS_DCACHE_OFF #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_ARCH_CPU_INIT #define CONFIG_ARCH_MISC_INIT -- cgit v1.3.1 From e62b008fe341030f4a80a09b66952bba65027b70 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sat, 4 Aug 2012 05:21:28 +0000 Subject: integrator: break out common config The configuration that is common for all Integrator boards may just as well be stored in a common include file as per pattern from other boards. This eases maintenance quite a bit. Signed-off-by: Linus Walleij --- include/configs/integrator-common.h | 103 ++++++++++++++++++++++++++++++++ include/configs/integratorap.h | 49 +-------------- include/configs/integratorcp.h | 115 ++---------------------------------- 3 files changed, 111 insertions(+), 156 deletions(-) create mode 100644 include/configs/integrator-common.h (limited to 'include') diff --git a/include/configs/integrator-common.h b/include/configs/integrator-common.h new file mode 100644 index 00000000000..564b418fa75 --- /dev/null +++ b/include/configs/integrator-common.h @@ -0,0 +1,103 @@ +/* + * (C) Copyright 2012 + * Linaro + * Linus Walleij + * Common ARM Integrator configuration settings + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#define CONFIG_INTEGRATOR + +#define CONFIG_SYS_TEXT_BASE 0x01000000 +#define CONFIG_SYS_MEMTEST_START 0x100000 +#define CONFIG_SYS_MEMTEST_END 0x10000000 +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */ +#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */ + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_MISC_INIT_R /* call misc_init_r during start up */ + +/* + * There are various dependencies on the core module (CM) fitted + * Users should refer to their CM user guide + */ +#include "armcoremodule.h" + +/* + * Initialize and remap the core module, use SPD to detect memory size + * If CONFIG_SKIP_LOWLEVEL_INIT is not defined & + * the core module has a CM_INIT register + * then the U-Boot initialisation code will + * e.g. ARM Boot Monitor or pre-loader is repeated once + * (to re-initialise any existing CM_INIT settings to safe values). + * + * This is usually not the desired behaviour since the platform + * will either reboot into the ARM monitor (or pre-loader) + * or continuously cycle thru it without U-Boot running, + * depending upon the setting of Integrator/CP switch S2-4. + * + * However it may be needed if Integrator/CP switch S2-1 + * is set OFF to boot direct into U-Boot. + * In that case comment out the line below. + */ +#define CONFIG_CM_INIT +#define CONFIG_CM_REMAP +#define CONFIG_CM_SPD_DETECT + +/* + * The ARM boot monitor initializes the board. + * However, the default U-Boot code also performs the initialization. + * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT + * - see documentation supplied with board for details of how to choose the + * image to run at reset/power up + * e.g. whether the ARM Boot Monitor runs before U-Boot + */ +/* #define CONFIG_SKIP_LOWLEVEL_INIT */ + +/* + * The ARM boot monitor does not relocate U-Boot. + * However, the default U-Boot code performs the relocation check, + * and may relocate the code if the memory map is changed. + * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT + */ +/* #define SKIP_CONFIG_RELOCATE_UBOOT */ + + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET diff --git a/include/configs/integratorap.h b/include/configs/integratorap.h index 2770c82b599..c6907b51284 100644 --- a/include/configs/integratorap.h +++ b/include/configs/integratorap.h @@ -31,32 +31,11 @@ #ifndef __CONFIG_H #define __CONFIG_H -#define CONFIG_INTEGRATOR +#include "integrator-common.h" + +/* Integrator/AP-specific configuration */ #define CONFIG_ARCH_INTEGRATOR -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SYS_TEXT_BASE 0x01000000 -#define CONFIG_SYS_MEMTEST_START 0x100000 -#define CONFIG_SYS_MEMTEST_END 0x10000000 -#define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_HZ_CLOCK 24000000 /* Timer 1 is clocked at 24Mhz */ -#define CONFIG_SYS_TIMERBASE 0x13000100 /* Timer1 */ - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */ - -#define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_CM_INIT 1 -#define CONFIG_CM_REMAP 1 -#define CONFIG_CM_SPD_DETECT - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* * PL010 Configuration @@ -90,29 +69,7 @@ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT "Integrator-AP # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_FLASH_BASE 0x24000000 diff --git a/include/configs/integratorcp.h b/include/configs/integratorcp.h index d5043df6f03..ca02a6f1d6b 100644 --- a/include/configs/integratorcp.h +++ b/include/configs/integratorcp.h @@ -31,32 +31,11 @@ #ifndef __CONFIG_H #define __CONFIG_H -/* Integrator-specific configuration */ -#define CONFIG_INTEGRATOR -#define CONFIG_ARCH_CINTEGRATOR -#define CONFIG_CM_INIT -#define CONFIG_CM_REMAP -#define CONFIG_CM_SPD_DETECT +#include "integrator-common.h" -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_SYS_TEXT_BASE 0x01000000 -#define CONFIG_SYS_MEMTEST_START 0x100000 -#define CONFIG_SYS_MEMTEST_END 0x10000000 -#define CONFIG_SYS_HZ 1000 +/* Integrator CP-specific configuration */ +#define CONFIG_ARCH_CINTEGRATOR #define CONFIG_SYS_HZ_CLOCK 1000000 /* Timer 1 is clocked at 1Mhz */ -#define CONFIG_SYS_TIMERBASE 0x13000100 - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r during start up */ - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) /* * Hardware drivers @@ -66,9 +45,7 @@ #define CONFIG_SMC91111_BASE 0xC8000000 #undef CONFIG_SMC91111_EXT_PHY -/* - * NS16550 Configuration - */ +/* PL011 configuration */ #define CONFIG_PL011_SERIAL #define CONFIG_PL011_CLOCK 14745600 #define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, (void *)CONFIG_SYS_SERIAL1 } @@ -77,16 +54,6 @@ #define CONFIG_SYS_SERIAL0 0x16000000 #define CONFIG_SYS_SERIAL1 0x17000000 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* * Command line configuration. */ @@ -102,32 +69,10 @@ /* * Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_PROMPT "Integrator-CP # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size*/ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size*/ -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 /* default load address */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- +/* * FLASH and environment organization - * Top varies according to amount fitted * Reserve top 4 blocks of flash * - ARM Boot Monitor @@ -136,7 +81,6 @@ * - U-Boot environment * * Base is always 0x24000000 - */ #define CONFIG_SYS_FLASH_BASE 0x24000000 #define CONFIG_SYS_FLASH_CFI 1 @@ -178,53 +122,4 @@ #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256KB */ #define CONFIG_ENV_SIZE 8192 /* 8KB */ -/* - * The ARM boot monitor initializes the board. - * However, the default U-Boot code also performs the initialization. - * If desired, this can be prevented by defining SKIP_LOWLEVEL_INIT - * - see documentation supplied with board for details of how to choose the - * image to run at reset/power up - * e.g. whether the ARM Boot Monitor runs before U-Boot - -#define CONFIG_SKIP_LOWLEVEL_INIT - - */ - -/* - * The ARM boot monitor does not relocate U-Boot. - * However, the default U-Boot code performs the relocation check, - * and may relocate the code if the memory map is changed. - * If necessary this can be prevented by defining SKIP_RELOCATE_UBOOT - -#define SKIP_CONFIG_RELOCATE_UBOOT - - */ -/*----------------------------------------------------------------------- - * There are various dependencies on the core module (CM) fitted - * Users should refer to their CM user guide - * - when porting adjust u-boot/Makefile accordingly - * to define the necessary CONFIG_ s for the CM involved - * see e.g. cp_926ejs_config - */ - -#include "armcoremodule.h" - -/* - * If CONFIG_SKIP_LOWLEVEL_INIT is not defined & - * the core module has a CM_INIT register - * then the U-Boot initialisation code will - * e.g. ARM Boot Monitor or pre-loader is repeated once - * (to re-initialise any existing CM_INIT settings to safe values). - * - * This is usually not the desired behaviour since the platform - * will either reboot into the ARM monitor (or pre-loader) - * or continuously cycle thru it without U-Boot running, - * depending upon the setting of Integrator/CP switch S2-4. - * - * However it may be needed if Integrator/CP switch S2-1 - * is set OFF to boot direct into U-Boot. - * In that case comment out the line below. -#undef CONFIG_CM_INIT - */ - #endif /* __CONFIG_H */ -- cgit v1.3.1 From 503e159b3e276a2d90f93c24177df353333135d4 Mon Sep 17 00:00:00 2001 From: Jens Scharsig Date: Mon, 3 Sep 2012 21:37:06 +0000 Subject: atmel: eb_cpux9k2: add ram target configuration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit * add ram target for EB+CPUx9k2 board (eb_cpux9k2_ram_config) Signed-off-by: Jens Scharsig Signed-off-by: Jens Scharsig (BuS Elektronik) Signed-off-by: Andreas Bießmann --- boards.cfg | 3 ++- include/configs/eb_cpux9k2.h | 7 ++++++- 2 files changed, 8 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/boards.cfg b/boards.cfg index 72e78034425..613d6b2927f 100644 --- a/boards.cfg +++ b/boards.cfg @@ -60,7 +60,8 @@ integratorcp_cm920t arm arm920t integrator armltd a320evb arm arm920t - faraday a320 at91rm9200ek arm arm920t at91rm9200ek atmel at91 at91rm9200ek at91rm9200ek_ram arm arm920t at91rm9200ek atmel at91 at91rm9200ek:RAMBOOT -eb_cpux9k2 arm arm920t - BuS at91 +eb_cpux9k2 arm arm920t eb_cpux9k2 BuS at91 eb_cpux9k2 +eb_cpux9k2_ram arm arm920t eb_cpux9k2 BuS at91 eb_cpux9k2:RAMBOOT cpuat91 arm arm920t cpuat91 eukrea at91 cpuat91 cpuat91_ram arm arm920t cpuat91 eukrea at91 cpuat91:RAMBOOT mx1ads arm arm920t - - imx diff --git a/include/configs/eb_cpux9k2.h b/include/configs/eb_cpux9k2.h index d4104de5f25..9371ec31f33 100644 --- a/include/configs/eb_cpux9k2.h +++ b/include/configs/eb_cpux9k2.h @@ -44,7 +44,12 @@ #define MACH_TYPE_EB_CPUX9K2 1977 #define CONFIG_MACH_TYPE MACH_TYPE_EB_CPUX9K2 /*--------------------------------------------------------------------------*/ -#define CONFIG_SYS_TEXT_BASE 0x00000000 +#ifndef CONFIG_RAMBOOT +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#else +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_TEXT_BASE 0x21f00000 +#endif #define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */ #define CONFIG_SYS_BOOT_SIZE 0x00 /* 0 KBytes */ -- cgit v1.3.1 From 7d899c14cc1842004e5f94a376082e7b6cf5988d Mon Sep 17 00:00:00 2001 From: Markus Hubig Date: Thu, 16 Aug 2012 08:22:09 +0000 Subject: Fixes the crippled console output on PortuxG20. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit In order to use the serial interface on the PortuxG20 we need to enable the level converter first by setting the PC9 pin to high. The level converter needs some time to settle so we have to use the mdelay() function to wait for some time. Unfortunately we have no timers available at board_early_init_f() so we enable the serial output early within board_postclk_init(). Now the U-Boot output looks fine: | U-Boot 2012.07-00132-gaf1a3b0-dirty (Aug 16 2012 - 18:21:32) | | CPU: AT91SAM9G20 | Crystal frequency: 18.432 MHz | CPU clock : 396.288 MHz | Master clock : 132.096 MHz | DRAM: 64 MiB | WARNING: Caches not enabled | NAND: 128 MiB | In: serial | Out: serial | Err: serial | Net: macb0 | Hit any key to stop autoboot: 0 Signed-off-by: Markus Hubig Signed-off-by: Andreas Bießmann --- board/taskit/stamp9g20/stamp9g20.c | 21 +++++++++++++++++---- include/configs/stamp9g20.h | 1 + 2 files changed, 18 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/board/taskit/stamp9g20/stamp9g20.c b/board/taskit/stamp9g20/stamp9g20.c index 5e07bf8d4e2..06df0af06f3 100644 --- a/board/taskit/stamp9g20/stamp9g20.c +++ b/board/taskit/stamp9g20/stamp9g20.c @@ -159,15 +159,28 @@ int board_early_init_f(void) return 0; } -int board_init(void) +int board_postclk_init(void) { - /* Adress of boot parameters */ - gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + /* + * Initialize the serial interface here, because be need a running + * timer to set PC9 to high and wait for some time to enable the + * level converter of the RS232 interface on the PortuxG20 board. + */ - /* Enable the serial interface */ +#ifdef CONFIG_PORTUXG20 at91_set_gpio_output(AT91_PIN_PC9, 1); + mdelay(1); +#endif at91_seriald_hw_init(); + return 0; +} + +int board_init(void) +{ + /* Adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + stamp9G20_nand_hw_init(); #ifdef CONFIG_MACB stamp9G20_macb_hw_init(); diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h index a2a0156a652..a881eef300e 100644 --- a/include/configs/stamp9g20.h +++ b/include/configs/stamp9g20.h @@ -59,6 +59,7 @@ #define CONFIG_INITRD_TAG /* pass initrd param to kernel */ #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ #define CONFIG_BOARD_EARLY_INIT_f /* call board_early_init_f() */ +#define CONFIG_BOARD_POSTCLK_INIT /* call board_postclk_init() */ #define CONFIG_DISPLAY_CPUINFO /* display CPU Info at startup */ /* setting board specific options */ -- cgit v1.3.1 From 8103c6f0fa141f19bd6b623f3f9153d9aeb47076 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 29 Aug 2012 01:21:59 +0000 Subject: OMAP3: tam3517: add function to read MAC from EEPROM The manufacturer delivers the TAM3517 SOM with 4 MAC address. They are stored on the EEPROM of the SOM. The patch adds a function to get their values and set the ethaddr variables. Signed-off-by: Stefano Babic --- include/configs/tam3517-common.h | 66 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 66 insertions(+) (limited to 'include') diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index 375265d475b..a13fd937621 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -124,6 +124,7 @@ #define CONFIG_CMD_NAND /* NAND support */ #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FLASH /* only NAND on the SOM */ #undef CONFIG_CMD_IMLS @@ -134,6 +135,9 @@ #define CONFIG_SYS_I2C_SLAVE 1 #define CONFIG_SYS_I2C_BUS 0 #define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 #define CONFIG_DRIVER_OMAP34XX_I2C @@ -347,4 +351,66 @@ "fi;" \ "else echo U-Boot not downloaded..exiting;fi\0" \ + +/* + * this is common code for all TAM3517 boards. + * MAC address is stored from manufacturer in + * I2C EEPROM + */ +#if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__)) + +/* + * The I2C EEPROM on the TAM3517 contains + * mac address and production data + */ +struct tam3517_module_info { + char customer[48]; + char product[48]; + + /* + * bit 0~47 : sequence number + * bit 48~55 : week of year, from 0. + * bit 56~63 : year + */ + unsigned long long sequence_number; + + /* + * bit 0~7 : revision fixed + * bit 8~15 : revision major + * bit 16~31 : TNxxx + */ + unsigned int revision; + unsigned char eth_addr[4][8]; + unsigned char _rev[100]; +}; + +#define TAM3517_READ_MAC_FROM_EEPROM \ +do { \ + struct tam3517_module_info info;\ + char buf[80], ethname[20]; \ + int i; \ + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); \ + if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, \ + (void *)&info, sizeof(info))) \ + break; \ + memset(buf, 0, sizeof(buf)); \ + for (i = 0 ; i < ARRAY_SIZE(info.eth_addr); i++) { \ + sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X", \ + info.eth_addr[i][5], \ + info.eth_addr[i][4], \ + info.eth_addr[i][3], \ + info.eth_addr[i][2], \ + info.eth_addr[i][1], \ + info.eth_addr[i][0]); \ + \ + if (i) \ + sprintf(ethname, "eth%daddr", i); \ + else \ + sprintf(ethname, "ethaddr"); \ + printf("Setting %s from EEPROM with %s\n", ethname, buf);\ + setenv(ethname, buf); \ + } \ +} while (0) +#endif + #endif /* __TAM3517_H */ -- cgit v1.3.1 From d0e9fb1cf904e328b987ffd66571161fb2e9bcaf Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 29 Aug 2012 01:22:02 +0000 Subject: OMAP3: mt_ventoux: activate GPIO4 Signed-off-by: Stefano Babic --- include/configs/mt_ventoux.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/mt_ventoux.h b/include/configs/mt_ventoux.h index 5db6d576664..131670a42b0 100644 --- a/include/configs/mt_ventoux.h +++ b/include/configs/mt_ventoux.h @@ -31,6 +31,7 @@ #define CONFIG_BOOTFILE "uImage" #define CONFIG_AUTO_COMPLETE +#define CONFIG_OMAP3_GPIO_4 #define CONFIG_HOSTNAME mt_ventoux /* -- cgit v1.3.1 From 629868755703aa173458531537cb8c4b570ed47c Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 29 Aug 2012 01:22:07 +0000 Subject: OMAP3: mt_ventoux: added video support Signed-off-by: Stefano Babic --- board/teejet/mt_ventoux/mt_ventoux.c | 83 ++++++++++++++++++++++++++++++++++++ board/teejet/mt_ventoux/mt_ventoux.h | 2 +- include/configs/mt_ventoux.h | 16 +++++++ 3 files changed, 100 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/board/teejet/mt_ventoux/mt_ventoux.c b/board/teejet/mt_ventoux/mt_ventoux.c index 814e72f0523..b8ad4471f52 100644 --- a/board/teejet/mt_ventoux/mt_ventoux.c +++ b/board/teejet/mt_ventoux/mt_ventoux.c @@ -21,13 +21,17 @@ #include #include +#include #include +#include #include #include #include #include #include #include +#include +#include #include #include #include @@ -53,6 +57,42 @@ DECLARE_GLOBAL_DATA_PTR; #define FPGA_INIT 119 #define FPGA_DONE 154 +#define LCD_PWR 138 +#define LCD_PON_PIN 139 + +#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) +static struct { + u32 xres; + u32 yres; +} panel_resolution[] = { + { 480, 272 }, + { 800, 480 } +}; + +static struct panel_config lcd_cfg[] = { + { + .timing_h = PANEL_TIMING_H(4, 8, 41), + .timing_v = PANEL_TIMING_V(2, 4, 10), + .pol_freq = 0x00000000, /* Pol Freq */ + .divisor = 0x0001000d, /* 33Mhz Pixel Clock */ + .panel_type = 0x01, /* TFT */ + .data_lines = 0x03, /* 24 Bit RGB */ + .load_mode = 0x02, /* Frame Mode */ + .panel_color = 0, + }, + { + .timing_h = PANEL_TIMING_H(20, 192, 4), + .timing_v = PANEL_TIMING_V(2, 20, 10), + .pol_freq = 0x00004000, /* Pol Freq */ + .divisor = 0x0001000E, /* 36Mhz Pixel Clock */ + .panel_type = 0x01, /* TFT */ + .data_lines = 0x03, /* 24 Bit RGB */ + .load_mode = 0x02, /* Frame Mode */ + .panel_color = 0, + } +}; +#endif + /* Timing definitions for FPGA */ static const u32 gpmc_fpga[] = { FPGA_GPMC_CONFIG1, @@ -254,3 +294,46 @@ int board_mmc_init(bd_t *bis) return omap_mmc_init(0, 0, 0); } #endif + +#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) +int board_video_init(void) +{ + struct prcm *prcm_base = (struct prcm *)PRCM_BASE; + struct panel_config *panel = &lcd_cfg[0]; + char *s; + u32 index = 0; + + void *fb; + + fb = (void *)0x88000000; + + s = getenv("panel"); + if (s) { + index = simple_strtoul(s, NULL, 10); + if (index < ARRAY_SIZE(lcd_cfg)) + panel = &lcd_cfg[index]; + else + return 0; + } + + panel->frame_buffer = fb; + printf("Panel: %dx%d\n", panel_resolution[index].xres, + panel_resolution[index].yres); + panel->lcd_size = (panel_resolution[index].yres - 1) << 16 | + (panel_resolution[index].xres - 1); + + gpio_request(LCD_PWR, "LCD Power"); + gpio_request(LCD_PON_PIN, "LCD Pon"); + gpio_direction_output(LCD_PWR, 0); + gpio_direction_output(LCD_PON_PIN, 1); + + + setbits_le32(&prcm_base->fclken_dss, FCK_DSS_ON); + setbits_le32(&prcm_base->iclken_dss, ICK_DSS_ON); + + omap3_dss_panel_config(panel); + omap3_dss_enable(); + + return 0; +} +#endif diff --git a/board/teejet/mt_ventoux/mt_ventoux.h b/board/teejet/mt_ventoux/mt_ventoux.h index eadb8a5d391..1cd7ec2ab29 100644 --- a/board/teejet/mt_ventoux/mt_ventoux.h +++ b/board/teejet/mt_ventoux/mt_ventoux.h @@ -203,7 +203,7 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(MMC2_DAT5), (IDIS | PTU | EN | M4)) \ MUX_VAL(CP(MMC2_DAT6), (IDIS | PTU | EN | M4)) \ /* GPIO_138: LCD_ENVD */\ - MUX_VAL(CP(MMC2_DAT7), (IDIS | PTU | EN | M4)) \ + MUX_VAL(CP(MMC2_DAT7), (IDIS | PTD | EN | M4)) \ /* GPIO_139: LCD_PON */\ /* McBSP */\ MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) \ diff --git a/include/configs/mt_ventoux.h b/include/configs/mt_ventoux.h index 131670a42b0..8d35943fa0f 100644 --- a/include/configs/mt_ventoux.h +++ b/include/configs/mt_ventoux.h @@ -2,6 +2,9 @@ * Copyright (C) 2011 * Stefano Babic, DENX Software Engineering, sbabic@denx.de. * + * + * Configuration settings for the Teejet mt_ventoux board. + * * Copyright (C) 2009 TechNexion Ltd. * * This program is free software; you can redistribute it and/or modify @@ -24,6 +27,10 @@ #include "tam3517-common.h" +#undef CONFIG_SYS_MALLOC_LEN +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10) + \ + 6 * 1024 * 1024) + #define MACH_TYPE_AM3517_MT_VENTOUX 3832 #define CONFIG_MACH_TYPE MACH_TYPE_AM3517_MT_VENTOUX @@ -63,6 +70,15 @@ #define CONFIG_FPGA_DELAY() udelay(1) #define CONFIG_SYS_FPGA_PROG_FEEDBACK +#define CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SPLASH_SCREEN +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_CMD_BMP +#define CONFIG_VIDEO_OMAP3 /* DSS Support */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + #define CONFIG_EXTRA_ENV_SETTINGS CONFIG_TAM3517_SETTINGS \ "bootcmd=run net_nfs\0" -- cgit v1.3.1 From 1b2080f3388b70c4c37b69830f73a61c50cdd505 Mon Sep 17 00:00:00 2001 From: Benoît Thébaudeau Date: Tue, 21 Aug 2012 11:05:12 +0000 Subject: mx25: Define default SoC input clock frequencies MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Define default SoC input clock frequencies for i.MX25 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau Cc: Stefano Babic Cc: Fabio Estevam Cc: Matthias Weisser --- arch/arm/cpu/arm926ejs/mx25/generic.c | 2 +- arch/arm/cpu/arm926ejs/mx25/timer.c | 16 ++++++++-------- arch/arm/include/asm/arch-mx25/clock.h | 14 ++++++++++++++ include/configs/mx25pdk.h | 1 - include/configs/zmx25.h | 1 - 5 files changed, 23 insertions(+), 11 deletions(-) (limited to 'include') diff --git a/arch/arm/cpu/arm926ejs/mx25/generic.c b/arch/arm/cpu/arm926ejs/mx25/generic.c index a412a8fe204..90e584ac585 100644 --- a/arch/arm/cpu/arm926ejs/mx25/generic.c +++ b/arch/arm/cpu/arm926ejs/mx25/generic.c @@ -64,7 +64,7 @@ static unsigned int imx_decode_pll(unsigned int pll, unsigned int f_ref) static ulong imx_get_mpllclk(void) { struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE; - ulong fref = 24000000; + ulong fref = MXC_HCLK; return imx_decode_pll(readl(&ccm->mpctl), fref); } diff --git a/arch/arm/cpu/arm926ejs/mx25/timer.c b/arch/arm/cpu/arm926ejs/mx25/timer.c index 1cfd02b2306..4dc4041c08d 100644 --- a/arch/arm/cpu/arm926ejs/mx25/timer.c +++ b/arch/arm/cpu/arm926ejs/mx25/timer.c @@ -40,6 +40,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -55,28 +56,27 @@ DECLARE_GLOBAL_DATA_PTR; static inline unsigned long long tick_to_time(unsigned long long tick) { tick *= CONFIG_SYS_HZ; - do_div(tick, CONFIG_MX25_CLK32); + do_div(tick, MXC_CLK32); return tick; } static inline unsigned long long time_to_tick(unsigned long long time) { - time *= CONFIG_MX25_CLK32; + time *= MXC_CLK32; do_div(time, CONFIG_SYS_HZ); return time; } static inline unsigned long long us_to_tick(unsigned long long us) { - us = us * CONFIG_MX25_CLK32 + 999999; + us = us * MXC_CLK32 + 999999; do_div(us, 1000000); return us; } #else /* ~2% error */ -#define TICK_PER_TIME ((CONFIG_MX25_CLK32 + CONFIG_SYS_HZ / 2) / \ - CONFIG_SYS_HZ) -#define US_PER_TICK (1000000 / CONFIG_MX25_CLK32) +#define TICK_PER_TIME ((MXC_CLK32 + CONFIG_SYS_HZ / 2) / CONFIG_SYS_HZ) +#define US_PER_TICK (1000000 / MXC_CLK32) static inline unsigned long long tick_to_time(unsigned long long tick) { @@ -144,7 +144,7 @@ ulong get_timer_masked(void) { /* * get_ticks() returns a long long (64 bit), it wraps in - * 2^64 / CONFIG_MX25_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ + * 2^64 / MXC_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ * 5 * 10^9 days... and get_ticks() * CONFIG_SYS_HZ wraps in * 5 * 10^6 days - long enough. */ @@ -177,6 +177,6 @@ ulong get_tbclk(void) { ulong tbclk; - tbclk = CONFIG_MX25_CLK32; + tbclk = MXC_CLK32; return tbclk; } diff --git a/arch/arm/include/asm/arch-mx25/clock.h b/arch/arm/include/asm/arch-mx25/clock.h index 0f47eaf053c..a313b806119 100644 --- a/arch/arm/include/asm/arch-mx25/clock.h +++ b/arch/arm/include/asm/arch-mx25/clock.h @@ -26,6 +26,20 @@ #ifndef __ASM_ARCH_CLOCK_H #define __ASM_ARCH_CLOCK_H +#include + +#ifdef CONFIG_MX25_HCLK_FREQ +#define MXC_HCLK CONFIG_MX25_HCLK_FREQ +#else +#define MXC_HCLK 24000000 +#endif + +#ifdef CONFIG_MX25_CLK32 +#define MXC_CLK32 CONFIG_MX25_CLK32 +#else +#define MXC_CLK32 32768 +#endif + enum mxc_clock { MXC_CSI_CLK, MXC_EPIT_CLK, diff --git a/include/configs/mx25pdk.h b/include/configs/mx25pdk.h index 359a3083054..96c143efb97 100644 --- a/include/configs/mx25pdk.h +++ b/include/configs/mx25pdk.h @@ -17,7 +17,6 @@ /* High Level Configuration Options */ -#define CONFIG_MX25_CLK32 32768 /* OSC32K frequency */ #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_TEXT_BASE 0x81200000 diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h index 072945ad4ab..447683a4905 100644 --- a/include/configs/zmx25.h +++ b/include/configs/zmx25.h @@ -28,7 +28,6 @@ #define CONFIG_ARM926EJS /* arm926ejs CPU core */ #define CONFIG_MX25 -#define CONFIG_MX25_CLK32 32768 /* OSC32K frequency */ #define CONFIG_SYS_HZ 1000 #define CONFIG_SYS_TEXT_BASE 0xA0000000 -- cgit v1.3.1 From 9c6c5c06764b7762a016b0ede002511139166fee Mon Sep 17 00:00:00 2001 From: Benoît Thébaudeau Date: Tue, 21 Aug 2012 11:07:20 +0000 Subject: mx35: Define default SoC input clock frequencies MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Define default SoC input clock frequencies for i.MX35 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau Cc: Stefano Babic Acked-by: Stefano Babic --- arch/arm/cpu/arm1136/mx35/generic.c | 43 +++++++++++++--------------------- arch/arm/cpu/arm1136/mx35/timer.c | 2 +- arch/arm/include/asm/arch-mx35/clock.h | 14 +++++++++++ include/configs/flea3.h | 1 - include/configs/mx35pdk.h | 1 - 5 files changed, 31 insertions(+), 30 deletions(-) (limited to 'include') diff --git a/arch/arm/cpu/arm1136/mx35/generic.c b/arch/arm/cpu/arm1136/mx35/generic.c index e4b07d07447..ef65176eed2 100644 --- a/arch/arm/cpu/arm1136/mx35/generic.c +++ b/arch/arm/cpu/arm1136/mx35/generic.c @@ -149,9 +149,7 @@ static u32 get_mcu_main_clk(void) struct ccm_regs *ccm = (struct ccm_regs *)IMX_CCM_BASE; arm_div = get_arm_div(readl(&ccm->pdr0), &fi, &fd); - fi *= - decode_pll(readl(&ccm->mpctl), - CONFIG_MX35_HCLK_FREQ); + fi *= decode_pll(readl(&ccm->mpctl), MXC_HCLK); return fi / (arm_div * fd); } @@ -193,12 +191,10 @@ u32 imx_get_uartclk(void) (struct ccm_regs *)IMX_CCM_BASE; u32 pdr4 = readl(&ccm->pdr4); - if (readl(&ccm->pdr3) & MXC_CCM_PDR3_UART_M_U) { + if (readl(&ccm->pdr3) & MXC_CCM_PDR3_UART_M_U) freq = get_mcu_main_clk(); - } else { - freq = decode_pll(readl(&ccm->ppctl), - CONFIG_MX35_HCLK_FREQ); - } + else + freq = decode_pll(readl(&ccm->ppctl), MXC_HCLK); freq /= CCM_GET_DIVIDER(pdr4, MXC_CCM_PDR4_UART_PODF_MASK, MXC_CCM_PDR4_UART_PODF_OFFSET) + 1; @@ -253,12 +249,10 @@ unsigned int mxc_get_main_clock(enum mxc_main_clock clk) break; case USB_CLK: usb_podf = (reg4 >> 22) & 0x3F; - if (reg4 & 0x200) { + if (reg4 & 0x200) pll = get_mcu_main_clk(); - } else { - pll = decode_pll(readl(&ccm->ppctl), - CONFIG_MX35_HCLK_FREQ); - } + else + pll = decode_pll(readl(&ccm->ppctl), MXC_HCLK); ret_val = pll / (usb_podf + 1); break; @@ -285,15 +279,14 @@ unsigned int mxc_get_peri_clock(enum mxc_peri_clock clk) clk_sel = mpdr3 & (1 << 14); pdf = (mpdr4 >> 10) & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / - (pdf + 1); + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / (pdf + 1); break; case SSI1_BAUD: pre_pdf = (mpdr2 >> 24) & 0x7; pdf = mpdr2 & 0x3F; clk_sel = mpdr2 & (1 << 6); ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / ((pre_pdf + 1) * (pdf + 1)); break; case SSI2_BAUD: @@ -301,15 +294,14 @@ unsigned int mxc_get_peri_clock(enum mxc_peri_clock clk) pdf = (mpdr2 >> 8) & 0x3F; clk_sel = mpdr2 & (1 << 6); ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / ((pre_pdf + 1) * (pdf + 1)); break; case CSI_BAUD: clk_sel = mpdr2 & (1 << 7); pdf = (mpdr2 >> 16) & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / - (pdf + 1); + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / (pdf + 1); break; case MSHC_CLK: pre_pdf = readl(&ccm->pdr1); @@ -317,36 +309,33 @@ unsigned int mxc_get_peri_clock(enum mxc_peri_clock clk) pdf = (pre_pdf >> 22) & 0x3F; pre_pdf = (pre_pdf >> 28) & 0x7; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / ((pre_pdf + 1) * (pdf + 1)); break; case ESDHC1_CLK: clk_sel = mpdr3 & 0x40; pdf = mpdr3 & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / - (pdf + 1); + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / (pdf + 1); break; case ESDHC2_CLK: clk_sel = mpdr3 & 0x40; pdf = (mpdr3 >> 8) & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / - (pdf + 1); + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / (pdf + 1); break; case ESDHC3_CLK: clk_sel = mpdr3 & 0x40; pdf = (mpdr3 >> 16) & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / - (pdf + 1); + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / (pdf + 1); break; case SPDIF_CLK: clk_sel = mpdr3 & 0x400000; pre_pdf = (mpdr3 >> 29) & 0x7; pdf = (mpdr3 >> 23) & 0x3F; ret_val = ((clk_sel != 0) ? mxc_get_main_clock(CPU_CLK) : - decode_pll(readl(&ccm->ppctl), CONFIG_MX35_HCLK_FREQ)) / + decode_pll(readl(&ccm->ppctl), MXC_HCLK)) / ((pre_pdf + 1) * (pdf + 1)); break; default: diff --git a/arch/arm/cpu/arm1136/mx35/timer.c b/arch/arm/cpu/arm1136/mx35/timer.c index 04937a1dfeb..60000429c4c 100644 --- a/arch/arm/cpu/arm1136/mx35/timer.c +++ b/arch/arm/cpu/arm1136/mx35/timer.c @@ -101,7 +101,7 @@ ulong get_timer_masked(void) { /* * get_ticks() returns a long long (64 bit), it wraps in - * 2^64 / CONFIG_MX25_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ + * 2^64 / MXC_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ * 5 * 10^9 days... and get_ticks() * CONFIG_SYS_HZ wraps in * 5 * 10^6 days - long enough. */ diff --git a/arch/arm/include/asm/arch-mx35/clock.h b/arch/arm/include/asm/arch-mx35/clock.h index e94f1244792..eb7458a338d 100644 --- a/arch/arm/include/asm/arch-mx35/clock.h +++ b/arch/arm/include/asm/arch-mx35/clock.h @@ -24,6 +24,20 @@ #ifndef __ASM_ARCH_CLOCK_H #define __ASM_ARCH_CLOCK_H +#include + +#ifdef CONFIG_MX35_HCLK_FREQ +#define MXC_HCLK CONFIG_MX35_HCLK_FREQ +#else +#define MXC_HCLK 24000000 +#endif + +#ifdef CONFIG_MX35_CLK32 +#define MXC_CLK32 CONFIG_MX35_CLK32 +#else +#define MXC_CLK32 32768 +#endif + enum mxc_clock { MXC_ARM_CLK, MXC_AHB_CLK, diff --git a/include/configs/flea3.h b/include/configs/flea3.h index 4350518939c..16f2d2ac48e 100644 --- a/include/configs/flea3.h +++ b/include/configs/flea3.h @@ -31,7 +31,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 /* This is an arm1136 CPU core */ #define CONFIG_MX35 -#define CONFIG_MX35_HCLK_FREQ 24000000 #define CONFIG_SYS_DCACHE_OFF #define CONFIG_SYS_CACHELINE_SIZE 32 diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h index 9bc6bd44705..834b97da778 100644 --- a/include/configs/mx35pdk.h +++ b/include/configs/mx35pdk.h @@ -31,7 +31,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 /* This is an arm1136 CPU core */ #define CONFIG_MX35 -#define CONFIG_MX35_HCLK_FREQ 24000000 #define CONFIG_DISPLAY_CPUINFO -- cgit v1.3.1 From 0dc7b82e4ec7cb95738aebd368d06a5cd8e37595 Mon Sep 17 00:00:00 2001 From: Benoît Thébaudeau Date: Tue, 21 Aug 2012 11:06:03 +0000 Subject: mx31: Define default SoC input clock frequencies MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Define default SoC input clock frequencies for i.MX31 in order to get rid of duplicated definitions. Signed-off-by: Benoît Thébaudeau Cc: Stefano Babic Cc: Fabio Estevam Cc: Wolfgang Denk Cc: Helmut Raiger --- arch/arm/cpu/arm1136/mx31/generic.c | 4 ++-- arch/arm/cpu/arm1136/mx31/timer.c | 16 ++++++++-------- arch/arm/include/asm/arch-mx31/clock.h | 14 ++++++++++++++ include/configs/imx31_litekit.h | 1 - include/configs/imx31_phycore.h | 1 - include/configs/mx31ads.h | 2 -- include/configs/mx31pdk.h | 2 -- include/configs/qong.h | 2 -- include/configs/tt01.h | 2 -- 9 files changed, 24 insertions(+), 20 deletions(-) (limited to 'include') diff --git a/arch/arm/cpu/arm1136/mx31/generic.c b/arch/arm/cpu/arm1136/mx31/generic.c index 3a35bfa3278..93f429cc52e 100644 --- a/arch/arm/cpu/arm1136/mx31/generic.c +++ b/arch/arm/cpu/arm1136/mx31/generic.c @@ -49,9 +49,9 @@ static u32 mx31_get_mpl_dpdgck_clk(void) u32 infreq; if ((readl(CCM_CCMR) & CCMR_PRCS_MASK) == CCMR_FPM) - infreq = CONFIG_MX31_CLK32 * 1024; + infreq = MXC_CLK32 * 1024; else - infreq = CONFIG_MX31_HCLK_FREQ; + infreq = MXC_HCLK; return mx31_decode_pll(readl(CCM_MPCTL), infreq); } diff --git a/arch/arm/cpu/arm1136/mx31/timer.c b/arch/arm/cpu/arm1136/mx31/timer.c index 72081a8bde2..36266da5aa8 100644 --- a/arch/arm/cpu/arm1136/mx31/timer.c +++ b/arch/arm/cpu/arm1136/mx31/timer.c @@ -23,6 +23,7 @@ #include #include +#include #include #include #include @@ -53,28 +54,27 @@ DECLARE_GLOBAL_DATA_PTR; static inline unsigned long long tick_to_time(unsigned long long tick) { tick *= CONFIG_SYS_HZ; - do_div(tick, CONFIG_MX31_CLK32); + do_div(tick, MXC_CLK32); return tick; } static inline unsigned long long time_to_tick(unsigned long long time) { - time *= CONFIG_MX31_CLK32; + time *= MXC_CLK32; do_div(time, CONFIG_SYS_HZ); return time; } static inline unsigned long long us_to_tick(unsigned long long us) { - us = us * CONFIG_MX31_CLK32 + 999999; + us = us * MXC_CLK32 + 999999; do_div(us, 1000000); return us; } #else /* ~2% error */ -#define TICK_PER_TIME ((CONFIG_MX31_CLK32 + CONFIG_SYS_HZ / 2) \ - / CONFIG_SYS_HZ) -#define US_PER_TICK (1000000 / CONFIG_MX31_CLK32) +#define TICK_PER_TIME ((MXC_CLK32 + CONFIG_SYS_HZ / 2) / CONFIG_SYS_HZ) +#define US_PER_TICK (1000000 / MXC_CLK32) static inline unsigned long long tick_to_time(unsigned long long tick) { @@ -128,7 +128,7 @@ ulong get_timer_masked(void) { /* * get_ticks() returns a long long (64 bit), it wraps in - * 2^64 / CONFIG_MX31_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ + * 2^64 / MXC_CLK32 = 2^64 / 2^15 = 2^49 ~ 5 * 10^14 (s) ~ * 5 * 10^9 days... and get_ticks() * CONFIG_SYS_HZ wraps in * 5 * 10^6 days - long enough. */ @@ -159,7 +159,7 @@ void __udelay(unsigned long usec) */ ulong get_tbclk(void) { - return CONFIG_MX31_CLK32; + return MXC_CLK32; } void reset_cpu(ulong addr) diff --git a/arch/arm/include/asm/arch-mx31/clock.h b/arch/arm/include/asm/arch-mx31/clock.h index 852c19c1a74..9468b45feb0 100644 --- a/arch/arm/include/asm/arch-mx31/clock.h +++ b/arch/arm/include/asm/arch-mx31/clock.h @@ -24,6 +24,20 @@ #ifndef __ASM_ARCH_CLOCK_H #define __ASM_ARCH_CLOCK_H +#include + +#ifdef CONFIG_MX31_HCLK_FREQ +#define MXC_HCLK CONFIG_MX31_HCLK_FREQ +#else +#define MXC_HCLK 26000000 +#endif + +#ifdef CONFIG_MX31_CLK32 +#define MXC_CLK32 CONFIG_MX31_CLK32 +#else +#define MXC_CLK32 32768 +#endif + enum mxc_clock { MXC_ARM_CLK, MXC_IPG_CLK, diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index 8cca4785780..6ae764a2d4a 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -33,7 +33,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */ #define CONFIG_MX31 1 /* in a mx31 */ -#define CONFIG_MX31_HCLK_FREQ 26000000 #define CONFIG_MX31_CLK32 32000 #define CONFIG_DISPLAY_CPUINFO diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h index b21621ca9e2..f36ceea57f6 100644 --- a/include/configs/imx31_phycore.h +++ b/include/configs/imx31_phycore.h @@ -33,7 +33,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 /* This is an arm1136 CPU core */ #define CONFIG_MX31 /* in a mx31 */ -#define CONFIG_MX31_HCLK_FREQ 26000000 #define CONFIG_MX31_CLK32 32000 #define CONFIG_DISPLAY_CPUINFO diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 081fbf69058..9d9f4a78229 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -27,8 +27,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */ #define CONFIG_MX31 1 /* in a mx31 */ -#define CONFIG_MX31_HCLK_FREQ 26000000 /* RedBoot says 26MHz */ -#define CONFIG_MX31_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index 17d3143eba8..b272674f820 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -35,8 +35,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 /* This is an arm1136 CPU core */ #define CONFIG_MX31 /* in a mx31 */ -#define CONFIG_MX31_HCLK_FREQ 26000000 -#define CONFIG_MX31_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO diff --git a/include/configs/qong.h b/include/configs/qong.h index 485e1b1f043..c2bd09729da 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -28,8 +28,6 @@ #define CONFIG_ARM1136 /* This is an arm1136 CPU core */ #define CONFIG_MX31 /* in a mx31 */ #define CONFIG_QONG -#define CONFIG_MX31_HCLK_FREQ 26000000 /* 26MHz */ -#define CONFIG_MX31_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO diff --git a/include/configs/tt01.h b/include/configs/tt01.h index cc68a42e86a..f46efa55f16 100644 --- a/include/configs/tt01.h +++ b/include/configs/tt01.h @@ -31,8 +31,6 @@ /* High Level Configuration Options */ #define CONFIG_ARM1136 #define CONFIG_MX31 -#define CONFIG_MX31_HCLK_FREQ 26000000 -#define CONFIG_MX31_CLK32 32768 #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO -- cgit v1.3.1 From b572595ee95829ab62e354c55a8fbd0f4db23935 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Sun, 29 Jul 2012 20:53:25 +0000 Subject: nand: Try to align the default buffers The NAND layer needs to use cache-aligned buffers by default. Towards this goal. align the default buffers and their members according to the minimum DMA alignment defined for the architecture. Signed-off-by: Simon Glass Signed-off-by: Tom Warren Acked-by: Scott Wood --- drivers/mtd/nand/nand_base.c | 3 ++- include/linux/mtd/nand.h | 7 ++++--- 2 files changed, 6 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c index bfd668fa0ac..891af1f2ea4 100644 --- a/drivers/mtd/nand/nand_base.c +++ b/drivers/mtd/nand/nand_base.c @@ -2936,7 +2936,8 @@ int nand_scan_tail(struct mtd_info *mtd) struct nand_chip *chip = mtd->priv; if (!(chip->options & NAND_OWN_BUFFERS)) - chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL); + chip->buffers = memalign(ARCH_DMA_MINALIGN, + sizeof(*chip->buffers)); if (!chip->buffers) return -ENOMEM; diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 82704de0835..dc839e71538 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -391,9 +391,10 @@ struct nand_ecc_ctrl { * consecutive order. */ struct nand_buffers { - uint8_t ecccalc[NAND_MAX_OOBSIZE]; - uint8_t ecccode[NAND_MAX_OOBSIZE]; - uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; + uint8_t ecccalc[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t ecccode[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t databuf[ALIGN(NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE, + ARCH_DMA_MINALIGN)]; }; /** -- cgit v1.3.1 From 312693c3dd280a73824c6403e249775ccb7c3547 Mon Sep 17 00:00:00 2001 From: Jim Lin Date: Sun, 29 Jul 2012 20:53:29 +0000 Subject: tegra: nand: Add Tegra NAND driver A device tree is used to configure the NAND, including memory timings and block/pages sizes. If this node is not present or is disabled, then NAND will not be initialized. Signed-off-by: Jim Lin Signed-off-by: Simon Glass Signed-off-by: Tom Warren --- arch/arm/include/asm/arch-tegra20/tegra20.h | 1 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/tegra_nand.c | 1026 +++++++++++++++++++++++++++ drivers/mtd/nand/tegra_nand.h | 257 +++++++ include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 6 files changed, 1287 insertions(+) create mode 100644 drivers/mtd/nand/tegra_nand.c create mode 100644 drivers/mtd/nand/tegra_nand.h (limited to 'include') diff --git a/arch/arm/include/asm/arch-tegra20/tegra20.h b/arch/arm/include/asm/arch-tegra20/tegra20.h index 6750754bae1..b2fb50e33e7 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra20.h +++ b/arch/arm/include/asm/arch-tegra20/tegra20.h @@ -39,6 +39,7 @@ #define NV_PA_APB_UARTC_BASE (NV_PA_APB_MISC_BASE + 0x6200) #define NV_PA_APB_UARTD_BASE (NV_PA_APB_MISC_BASE + 0x6300) #define NV_PA_APB_UARTE_BASE (NV_PA_APB_MISC_BASE + 0x6400) +#define TEGRA20_NAND_BASE (NV_PA_APB_MISC_BASE + 0x8000) #define TEGRA20_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) #define TEGRA20_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) #define TEGRA20_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile index 29dc20ef5e2..beb99cacb66 100644 --- a/drivers/mtd/nand/Makefile +++ b/drivers/mtd/nand/Makefile @@ -62,6 +62,7 @@ COBJS-$(CONFIG_NAND_NOMADIK) += nomadik.o COBJS-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o COBJS-$(CONFIG_NAND_S3C64XX) += s3c64xx.o COBJS-$(CONFIG_NAND_SPEAR) += spr_nand.o +COBJS-$(CONFIG_TEGRA_NAND) += tegra_nand.o COBJS-$(CONFIG_NAND_OMAP_GPMC) += omap_gpmc.o COBJS-$(CONFIG_NAND_PLAT) += nand_plat.o endif diff --git a/drivers/mtd/nand/tegra_nand.c b/drivers/mtd/nand/tegra_nand.c new file mode 100644 index 00000000000..8c1de34455e --- /dev/null +++ b/drivers/mtd/nand/tegra_nand.c @@ -0,0 +1,1026 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * (C) Copyright 2011 NVIDIA Corporation + * (C) Copyright 2006 Detlev Zundel, dzu@denx.de + * (C) Copyright 2006 DENX Software Engineering + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "tegra_nand.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define NAND_CMD_TIMEOUT_MS 10 + +#define SKIPPED_SPARE_BYTES 4 + +/* ECC bytes to be generated for tag data */ +#define TAG_ECC_BYTES 4 + +/* 64 byte oob block info for large page (== 2KB) device + * + * OOB flash layout for Tegra with Reed-Solomon 4 symbol correct ECC: + * Skipped bytes(4) + * Main area Ecc(36) + * Tag data(20) + * Tag data Ecc(4) + * + * Yaffs2 will use 16 tag bytes. + */ +static struct nand_ecclayout eccoob = { + .eccbytes = 36, + .eccpos = { + 4, 5, 6, 7, 8, 9, 10, 11, 12, + 13, 14, 15, 16, 17, 18, 19, 20, 21, + 22, 23, 24, 25, 26, 27, 28, 29, 30, + 31, 32, 33, 34, 35, 36, 37, 38, 39, + }, + .oobavail = 20, + .oobfree = { + { + .offset = 40, + .length = 20, + }, + } +}; + +enum { + ECC_OK, + ECC_TAG_ERROR = 1 << 0, + ECC_DATA_ERROR = 1 << 1 +}; + +/* Timing parameters */ +enum { + FDT_NAND_MAX_TRP_TREA, + FDT_NAND_TWB, + FDT_NAND_MAX_TCR_TAR_TRR, + FDT_NAND_TWHR, + FDT_NAND_MAX_TCS_TCH_TALS_TALH, + FDT_NAND_TWH, + FDT_NAND_TWP, + FDT_NAND_TRH, + FDT_NAND_TADL, + + FDT_NAND_TIMING_COUNT +}; + +/* Information about an attached NAND chip */ +struct fdt_nand { + struct nand_ctlr *reg; + int enabled; /* 1 to enable, 0 to disable */ + struct fdt_gpio_state wp_gpio; /* write-protect GPIO */ + s32 width; /* bit width, normally 8 */ + u32 timing[FDT_NAND_TIMING_COUNT]; +}; + +struct nand_drv { + struct nand_ctlr *reg; + + /* + * When running in PIO mode to get READ ID bytes from register + * RESP_0, we need this variable as an index to know which byte in + * register RESP_0 should be read. + * Because common code in nand_base.c invokes read_byte function two + * times for NAND_CMD_READID. + * And our controller returns 4 bytes at once in register RESP_0. + */ + int pio_byte_index; + struct fdt_nand config; +}; + +static struct nand_drv nand_ctrl; +static struct mtd_info *our_mtd; +static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; + +#ifdef CONFIG_SYS_DCACHE_OFF +static inline void dma_prepare(void *start, unsigned long length, + int is_writing) +{ +} +#else +/** + * Prepare for a DMA transaction + * + * For a write we flush out our data. For a read we invalidate, since we + * need to do this before we read from the buffer after the DMA has + * completed, so may as well do it now. + * + * @param start Start address for DMA buffer (should be cache-aligned) + * @param length Length of DMA buffer in bytes + * @param is_writing 0 if reading, non-zero if writing + */ +static void dma_prepare(void *start, unsigned long length, int is_writing) +{ + unsigned long addr = (unsigned long)start; + + length = ALIGN(length, ARCH_DMA_MINALIGN); + if (is_writing) + flush_dcache_range(addr, addr + length); + else + invalidate_dcache_range(addr, addr + length); +} +#endif + +/** + * Wait for command completion + * + * @param reg nand_ctlr structure + * @return + * 1 - Command completed + * 0 - Timeout + */ +static int nand_waitfor_cmd_completion(struct nand_ctlr *reg) +{ + u32 reg_val; + int running; + int i; + + for (i = 0; i < NAND_CMD_TIMEOUT_MS * 1000; i++) { + if ((readl(®->command) & CMD_GO) || + !(readl(®->status) & STATUS_RBSY0) || + !(readl(®->isr) & ISR_IS_CMD_DONE)) { + udelay(1); + continue; + } + reg_val = readl(®->dma_mst_ctrl); + /* + * If DMA_MST_CTRL_EN_A_ENABLE or DMA_MST_CTRL_EN_B_ENABLE + * is set, that means DMA engine is running. + * + * Then we have to wait until DMA_MST_CTRL_IS_DMA_DONE + * is cleared, indicating DMA transfer completion. + */ + running = reg_val & (DMA_MST_CTRL_EN_A_ENABLE | + DMA_MST_CTRL_EN_B_ENABLE); + if (!running || (reg_val & DMA_MST_CTRL_IS_DMA_DONE)) + return 1; + udelay(1); + } + return 0; +} + +/** + * Read one byte from the chip + * + * @param mtd MTD device structure + * @return data byte + * + * Read function for 8bit bus-width + */ +static uint8_t read_byte(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + u32 dword_read; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + /* In PIO mode, only 4 bytes can be transferred with single CMD_GO. */ + if (info->pio_byte_index > 3) { + info->pio_byte_index = 0; + writel(CMD_GO | CMD_PIO + | CMD_RX | CMD_CE0, + &info->reg->command); + if (!nand_waitfor_cmd_completion(info->reg)) + printf("Command timeout\n"); + } + + dword_read = readl(&info->reg->resp); + dword_read = dword_read >> (8 * info->pio_byte_index); + info->pio_byte_index++; + return (uint8_t)dword_read; +} + +/** + * Check NAND status to see if it is ready or not + * + * @param mtd MTD device structure + * @return + * 1 - ready + * 0 - not ready + */ +static int nand_dev_ready(struct mtd_info *mtd) +{ + struct nand_chip *chip = mtd->priv; + int reg_val; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + reg_val = readl(&info->reg->status); + if (reg_val & STATUS_RBSY0) + return 1; + else + return 0; +} + +/* Dummy implementation: we don't support multiple chips */ +static void nand_select_chip(struct mtd_info *mtd, int chipnr) +{ + switch (chipnr) { + case -1: + case 0: + break; + + default: + BUG(); + } +} + +/** + * Clear all interrupt status bits + * + * @param reg nand_ctlr structure + */ +static void nand_clear_interrupt_status(struct nand_ctlr *reg) +{ + u32 reg_val; + + /* Clear interrupt status */ + reg_val = readl(®->isr); + writel(reg_val, ®->isr); +} + +/** + * Send command to NAND device + * + * @param mtd MTD device structure + * @param command the command to be sent + * @param column the column address for this command, -1 if none + * @param page_addr the page address for this command, -1 if none + */ +static void nand_command(struct mtd_info *mtd, unsigned int command, + int column, int page_addr) +{ + struct nand_chip *chip = mtd->priv; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + /* + * Write out the command to the device. + * + * Only command NAND_CMD_RESET or NAND_CMD_READID will come + * here before mtd->writesize is initialized. + */ + + /* Emulate NAND_CMD_READOOB */ + if (command == NAND_CMD_READOOB) { + assert(mtd->writesize != 0); + column += mtd->writesize; + command = NAND_CMD_READ0; + } + + /* Adjust columns for 16 bit bus-width */ + if (column != -1 && (chip->options & NAND_BUSWIDTH_16)) + column >>= 1; + + nand_clear_interrupt_status(info->reg); + + /* Stop DMA engine, clear DMA completion status */ + writel(DMA_MST_CTRL_EN_A_DISABLE + | DMA_MST_CTRL_EN_B_DISABLE + | DMA_MST_CTRL_IS_DMA_DONE, + &info->reg->dma_mst_ctrl); + + /* + * Program and erase have their own busy handlers + * status and sequential in needs no delay + */ + switch (command) { + case NAND_CMD_READID: + writel(NAND_CMD_READID, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_ALE | CMD_PIO + | CMD_RX | + ((4 - 1) << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0, + &info->reg->command); + info->pio_byte_index = 0; + break; + case NAND_CMD_READ0: + writel(NAND_CMD_READ0, &info->reg->cmd_reg1); + writel(NAND_CMD_READSTART, &info->reg->cmd_reg2); + writel((page_addr << 16) | (column & 0xFFFF), + &info->reg->addr_reg1); + writel(page_addr >> 16, &info->reg->addr_reg2); + return; + case NAND_CMD_SEQIN: + writel(NAND_CMD_SEQIN, &info->reg->cmd_reg1); + writel(NAND_CMD_PAGEPROG, &info->reg->cmd_reg2); + writel((page_addr << 16) | (column & 0xFFFF), + &info->reg->addr_reg1); + writel(page_addr >> 16, + &info->reg->addr_reg2); + return; + case NAND_CMD_PAGEPROG: + return; + case NAND_CMD_ERASE1: + writel(NAND_CMD_ERASE1, &info->reg->cmd_reg1); + writel(NAND_CMD_ERASE2, &info->reg->cmd_reg2); + writel(page_addr, &info->reg->addr_reg1); + writel(CMD_GO | CMD_CLE | CMD_ALE | + CMD_SEC_CMD | CMD_CE0 | CMD_ALE_BYTES3, + &info->reg->command); + break; + case NAND_CMD_ERASE2: + return; + case NAND_CMD_STATUS: + writel(NAND_CMD_STATUS, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_PIO | CMD_RX + | ((1 - 0) << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0, + &info->reg->command); + info->pio_byte_index = 0; + break; + case NAND_CMD_RESET: + writel(NAND_CMD_RESET, &info->reg->cmd_reg1); + writel(CMD_GO | CMD_CLE | CMD_CE0, + &info->reg->command); + break; + case NAND_CMD_RNDOUT: + default: + printf("%s: Unsupported command %d\n", __func__, command); + return; + } + if (!nand_waitfor_cmd_completion(info->reg)) + printf("Command 0x%02X timeout\n", command); +} + +/** + * Check whether the pointed buffer are all 0xff (blank). + * + * @param buf data buffer for blank check + * @param len length of the buffer in byte + * @return + * 1 - blank + * 0 - non-blank + */ +static int blank_check(u8 *buf, int len) +{ + int i; + + for (i = 0; i < len; i++) + if (buf[i] != 0xFF) + return 0; + return 1; +} + +/** + * After a DMA transfer for read, we call this function to see whether there + * is any uncorrectable error on the pointed data buffer or oob buffer. + * + * @param reg nand_ctlr structure + * @param databuf data buffer + * @param a_len data buffer length + * @param oobbuf oob buffer + * @param b_len oob buffer length + * @return + * ECC_OK - no ECC error or correctable ECC error + * ECC_TAG_ERROR - uncorrectable tag ECC error + * ECC_DATA_ERROR - uncorrectable data ECC error + * ECC_DATA_ERROR + ECC_TAG_ERROR - uncorrectable data+tag ECC error + */ +static int check_ecc_error(struct nand_ctlr *reg, u8 *databuf, + int a_len, u8 *oobbuf, int b_len) +{ + int return_val = ECC_OK; + u32 reg_val; + + if (!(readl(®->isr) & ISR_IS_ECC_ERR)) + return ECC_OK; + + /* + * Area A is used for the data block (databuf). Area B is used for + * the spare block (oobbuf) + */ + reg_val = readl(®->dec_status); + if ((reg_val & DEC_STATUS_A_ECC_FAIL) && databuf) { + reg_val = readl(®->bch_dec_status_buf); + /* + * If uncorrectable error occurs on data area, then see whether + * they are all FF. If all are FF, it's a blank page. + * Not error. + */ + if ((reg_val & BCH_DEC_STATUS_FAIL_SEC_FLAG_MASK) && + !blank_check(databuf, a_len)) + return_val |= ECC_DATA_ERROR; + } + + if ((reg_val & DEC_STATUS_B_ECC_FAIL) && oobbuf) { + reg_val = readl(®->bch_dec_status_buf); + /* + * If uncorrectable error occurs on tag area, then see whether + * they are all FF. If all are FF, it's a blank page. + * Not error. + */ + if ((reg_val & BCH_DEC_STATUS_FAIL_TAG_MASK) && + !blank_check(oobbuf, b_len)) + return_val |= ECC_TAG_ERROR; + } + + return return_val; +} + +/** + * Set GO bit to send command to device + * + * @param reg nand_ctlr structure + */ +static void start_command(struct nand_ctlr *reg) +{ + u32 reg_val; + + reg_val = readl(®->command); + reg_val |= CMD_GO; + writel(reg_val, ®->command); +} + +/** + * Clear command GO bit, DMA GO bit, and DMA completion status + * + * @param reg nand_ctlr structure + */ +static void stop_command(struct nand_ctlr *reg) +{ + /* Stop command */ + writel(0, ®->command); + + /* Stop DMA engine and clear DMA completion status */ + writel(DMA_MST_CTRL_GO_DISABLE + | DMA_MST_CTRL_IS_DMA_DONE, + ®->dma_mst_ctrl); +} + +/** + * Set up NAND bus width and page size + * + * @param info nand_info structure + * @param *reg_val address of reg_val + * @return 0 if ok, -1 on error + */ +static int set_bus_width_page_size(struct fdt_nand *config, + u32 *reg_val) +{ + if (config->width == 8) + *reg_val = CFG_BUS_WIDTH_8BIT; + else if (config->width == 16) + *reg_val = CFG_BUS_WIDTH_16BIT; + else { + debug("%s: Unsupported bus width %d\n", __func__, + config->width); + return -1; + } + + if (our_mtd->writesize == 512) + *reg_val |= CFG_PAGE_SIZE_512; + else if (our_mtd->writesize == 2048) + *reg_val |= CFG_PAGE_SIZE_2048; + else if (our_mtd->writesize == 4096) + *reg_val |= CFG_PAGE_SIZE_4096; + else { + debug("%s: Unsupported page size %d\n", __func__, + our_mtd->writesize); + return -1; + } + + return 0; +} + +/** + * Page read/write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + * @param page page number + * @param with_ecc 1 to enable ECC, 0 to disable ECC + * @param is_writing 0 for read, 1 for write + * @return 0 when successfully completed + * -EIO when command timeout + */ +static int nand_rw_page(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int page, int with_ecc, int is_writing) +{ + u32 reg_val; + int tag_size; + struct nand_oobfree *free = chip->ecc.layout->oobfree; + /* 4*128=512 (byte) is the value that our HW can support. */ + ALLOC_CACHE_ALIGN_BUFFER(u32, tag_buf, 128); + char *tag_ptr; + struct nand_drv *info; + struct fdt_nand *config; + + if ((uintptr_t)buf & 0x03) { + printf("buf %p has to be 4-byte aligned\n", buf); + return -EINVAL; + } + + info = (struct nand_drv *)chip->priv; + config = &info->config; + if (set_bus_width_page_size(config, ®_val)) + return -EINVAL; + + /* Need to be 4-byte aligned */ + tag_ptr = (char *)tag_buf; + + stop_command(info->reg); + + writel((1 << chip->page_shift) - 1, &info->reg->dma_cfg_a); + writel(virt_to_phys(buf), &info->reg->data_block_ptr); + + if (with_ecc) { + writel(virt_to_phys(tag_ptr), &info->reg->tag_ptr); + if (is_writing) + memcpy(tag_ptr, chip->oob_poi + free->offset, + chip->ecc.layout->oobavail + + TAG_ECC_BYTES); + } else { + writel(virt_to_phys(chip->oob_poi), &info->reg->tag_ptr); + } + + /* Set ECC selection, configure ECC settings */ + if (with_ecc) { + tag_size = chip->ecc.layout->oobavail + TAG_ECC_BYTES; + reg_val |= (CFG_SKIP_SPARE_SEL_4 + | CFG_SKIP_SPARE_ENABLE + | CFG_HW_ECC_CORRECTION_ENABLE + | CFG_ECC_EN_TAG_DISABLE + | CFG_HW_ECC_SEL_RS + | CFG_HW_ECC_ENABLE + | CFG_TVAL4 + | (tag_size - 1)); + + if (!is_writing) + tag_size += SKIPPED_SPARE_BYTES; + dma_prepare(tag_ptr, tag_size, is_writing); + } else { + tag_size = mtd->oobsize; + reg_val |= (CFG_SKIP_SPARE_DISABLE + | CFG_HW_ECC_CORRECTION_DISABLE + | CFG_ECC_EN_TAG_DISABLE + | CFG_HW_ECC_DISABLE + | (tag_size - 1)); + dma_prepare(chip->oob_poi, tag_size, is_writing); + } + writel(reg_val, &info->reg->config); + + dma_prepare(buf, 1 << chip->page_shift, is_writing); + + writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config); + + writel(tag_size - 1, &info->reg->dma_cfg_b); + + nand_clear_interrupt_status(info->reg); + + reg_val = CMD_CLE | CMD_ALE + | CMD_SEC_CMD + | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT) + | CMD_A_VALID + | CMD_B_VALID + | (CMD_TRANS_SIZE_PAGE << CMD_TRANS_SIZE_SHIFT) + | CMD_CE0; + if (!is_writing) + reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX); + else + reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX); + writel(reg_val, &info->reg->command); + + /* Setup DMA engine */ + reg_val = DMA_MST_CTRL_GO_ENABLE + | DMA_MST_CTRL_BURST_8WORDS + | DMA_MST_CTRL_EN_A_ENABLE + | DMA_MST_CTRL_EN_B_ENABLE; + + if (!is_writing) + reg_val |= DMA_MST_CTRL_DIR_READ; + else + reg_val |= DMA_MST_CTRL_DIR_WRITE; + + writel(reg_val, &info->reg->dma_mst_ctrl); + + start_command(info->reg); + + if (!nand_waitfor_cmd_completion(info->reg)) { + if (!is_writing) + printf("Read Page 0x%X timeout ", page); + else + printf("Write Page 0x%X timeout ", page); + if (with_ecc) + printf("with ECC"); + else + printf("without ECC"); + printf("\n"); + return -EIO; + } + + if (with_ecc && !is_writing) { + memcpy(chip->oob_poi, tag_ptr, + SKIPPED_SPARE_BYTES); + memcpy(chip->oob_poi + free->offset, + tag_ptr + SKIPPED_SPARE_BYTES, + chip->ecc.layout->oobavail); + reg_val = (u32)check_ecc_error(info->reg, (u8 *)buf, + 1 << chip->page_shift, + (u8 *)(tag_ptr + SKIPPED_SPARE_BYTES), + chip->ecc.layout->oobavail); + if (reg_val & ECC_TAG_ERROR) + printf("Read Page 0x%X tag ECC error\n", page); + if (reg_val & ECC_DATA_ERROR) + printf("Read Page 0x%X data ECC error\n", + page); + if (reg_val & (ECC_DATA_ERROR | ECC_TAG_ERROR)) + return -EIO; + } + return 0; +} + +/** + * Hardware ecc based page read function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf buffer to store read data + * @param page page number to read + * @return 0 when successfully completed + * -EIO when command timeout + */ +static int nand_read_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int page) +{ + return nand_rw_page(mtd, chip, buf, page, 1, 0); +} + +/** + * Hardware ecc based page write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + */ +static void nand_write_page_hwecc(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf) +{ + int page; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + + page = (readl(&info->reg->addr_reg1) >> 16) | + (readl(&info->reg->addr_reg2) << 16); + + nand_rw_page(mtd, chip, (uint8_t *)buf, page, 1, 1); +} + + +/** + * Read raw page data without ecc + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf buffer to store read data + * @param page page number to read + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_read_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, uint8_t *buf, int page) +{ + return nand_rw_page(mtd, chip, buf, page, 0, 0); +} + +/** + * Raw page write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param buf data buffer + */ +static void nand_write_page_raw(struct mtd_info *mtd, + struct nand_chip *chip, const uint8_t *buf) +{ + int page; + struct nand_drv *info; + + info = (struct nand_drv *)chip->priv; + page = (readl(&info->reg->addr_reg1) >> 16) | + (readl(&info->reg->addr_reg2) << 16); + + nand_rw_page(mtd, chip, (uint8_t *)buf, page, 0, 1); +} + +/** + * OOB data read/write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to read + * @param with_ecc 1 to enable ECC, 0 to disable ECC + * @param is_writing 0 for read, 1 for write + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_rw_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page, int with_ecc, int is_writing) +{ + u32 reg_val; + int tag_size; + struct nand_oobfree *free = chip->ecc.layout->oobfree; + struct nand_drv *info; + + if (((int)chip->oob_poi) & 0x03) + return -EINVAL; + info = (struct nand_drv *)chip->priv; + if (set_bus_width_page_size(&info->config, ®_val)) + return -EINVAL; + + stop_command(info->reg); + + writel(virt_to_phys(chip->oob_poi), &info->reg->tag_ptr); + + /* Set ECC selection */ + tag_size = mtd->oobsize; + if (with_ecc) + reg_val |= CFG_ECC_EN_TAG_ENABLE; + else + reg_val |= (CFG_ECC_EN_TAG_DISABLE); + + reg_val |= ((tag_size - 1) | + CFG_SKIP_SPARE_DISABLE | + CFG_HW_ECC_CORRECTION_DISABLE | + CFG_HW_ECC_DISABLE); + writel(reg_val, &info->reg->config); + + dma_prepare(chip->oob_poi, tag_size, is_writing); + + writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config); + + if (is_writing && with_ecc) + tag_size -= TAG_ECC_BYTES; + + writel(tag_size - 1, &info->reg->dma_cfg_b); + + nand_clear_interrupt_status(info->reg); + + reg_val = CMD_CLE | CMD_ALE + | CMD_SEC_CMD + | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT) + | CMD_B_VALID + | CMD_CE0; + if (!is_writing) + reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX); + else + reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX); + writel(reg_val, &info->reg->command); + + /* Setup DMA engine */ + reg_val = DMA_MST_CTRL_GO_ENABLE + | DMA_MST_CTRL_BURST_8WORDS + | DMA_MST_CTRL_EN_B_ENABLE; + if (!is_writing) + reg_val |= DMA_MST_CTRL_DIR_READ; + else + reg_val |= DMA_MST_CTRL_DIR_WRITE; + + writel(reg_val, &info->reg->dma_mst_ctrl); + + start_command(info->reg); + + if (!nand_waitfor_cmd_completion(info->reg)) { + if (!is_writing) + printf("Read OOB of Page 0x%X timeout\n", page); + else + printf("Write OOB of Page 0x%X timeout\n", page); + return -EIO; + } + + if (with_ecc && !is_writing) { + reg_val = (u32)check_ecc_error(info->reg, 0, 0, + (u8 *)(chip->oob_poi + free->offset), + chip->ecc.layout->oobavail); + if (reg_val & ECC_TAG_ERROR) + printf("Read OOB of Page 0x%X tag ECC error\n", page); + } + return 0; +} + +/** + * OOB data read function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to read + * @param sndcmd flag whether to issue read command or not + * @return 1 - issue read command next time + * 0 - not to issue + */ +static int nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page, int sndcmd) +{ + if (sndcmd) { + chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); + sndcmd = 0; + } + nand_rw_oob(mtd, chip, page, 0, 0); + return sndcmd; +} + +/** + * OOB data write function + * + * @param mtd mtd info structure + * @param chip nand chip info structure + * @param page page number to write + * @return 0 when successfully completed + * -EINVAL when chip->oob_poi is not double-word aligned + * -EIO when command timeout + */ +static int nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, + int page) +{ + chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); + + return nand_rw_oob(mtd, chip, page, 0, 1); +} + +/** + * Set up NAND memory timings according to the provided parameters + * + * @param timing Timing parameters + * @param reg NAND controller register address + */ +static void setup_timing(unsigned timing[FDT_NAND_TIMING_COUNT], + struct nand_ctlr *reg) +{ + u32 reg_val, clk_rate, clk_period, time_val; + + clk_rate = (u32)clock_get_periph_rate(PERIPH_ID_NDFLASH, + CLOCK_ID_PERIPH) / 1000000; + clk_period = 1000 / clk_rate; + reg_val = ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) << + TIMING_TRP_RESP_CNT_SHIFT) & TIMING_TRP_RESP_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWB] / clk_period) << + TIMING_TWB_CNT_SHIFT) & TIMING_TWB_CNT_MASK; + time_val = timing[FDT_NAND_MAX_TCR_TAR_TRR] / clk_period; + if (time_val > 2) + reg_val |= ((time_val - 2) << TIMING_TCR_TAR_TRR_CNT_SHIFT) & + TIMING_TCR_TAR_TRR_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWHR] / clk_period) << + TIMING_TWHR_CNT_SHIFT) & TIMING_TWHR_CNT_MASK; + time_val = timing[FDT_NAND_MAX_TCS_TCH_TALS_TALH] / clk_period; + if (time_val > 1) + reg_val |= ((time_val - 1) << TIMING_TCS_CNT_SHIFT) & + TIMING_TCS_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWH] / clk_period) << + TIMING_TWH_CNT_SHIFT) & TIMING_TWH_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TWP] / clk_period) << + TIMING_TWP_CNT_SHIFT) & TIMING_TWP_CNT_MASK; + reg_val |= ((timing[FDT_NAND_TRH] / clk_period) << + TIMING_TRH_CNT_SHIFT) & TIMING_TRH_CNT_MASK; + reg_val |= ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) << + TIMING_TRP_CNT_SHIFT) & TIMING_TRP_CNT_MASK; + writel(reg_val, ®->timing); + + reg_val = 0; + time_val = timing[FDT_NAND_TADL] / clk_period; + if (time_val > 2) + reg_val = (time_val - 2) & TIMING2_TADL_CNT_MASK; + writel(reg_val, ®->timing2); +} + +/** + * Decode NAND parameters from the device tree + * + * @param blob Device tree blob + * @param node Node containing "nand-flash" compatble node + * @return 0 if ok, -ve on error (FDT_ERR_...) + */ +static int fdt_decode_nand(const void *blob, int node, struct fdt_nand *config) +{ + int err; + + config->reg = (struct nand_ctlr *)fdtdec_get_addr(blob, node, "reg"); + config->enabled = fdtdec_get_is_enabled(blob, node); + config->width = fdtdec_get_int(blob, node, "nvidia,nand-width", 8); + err = fdtdec_decode_gpio(blob, node, "nvidia,wp-gpios", + &config->wp_gpio); + if (err) + return err; + err = fdtdec_get_int_array(blob, node, "nvidia,timing", + config->timing, FDT_NAND_TIMING_COUNT); + if (err < 0) + return err; + + /* Now look up the controller and decode that */ + node = fdt_next_node(blob, node, NULL); + if (node < 0) + return node; + + return 0; +} + +/** + * Board-specific NAND initialization + * + * @param nand nand chip info structure + * @return 0, after initialized, -1 on error + */ +int tegra_nand_init(struct nand_chip *nand, int devnum) +{ + struct nand_drv *info = &nand_ctrl; + struct fdt_nand *config = &info->config; + int node, ret; + + node = fdtdec_next_compatible(gd->fdt_blob, 0, + COMPAT_NVIDIA_TEGRA20_NAND); + if (node < 0) + return -1; + if (fdt_decode_nand(gd->fdt_blob, node, config)) { + printf("Could not decode nand-flash in device tree\n"); + return -1; + } + if (!config->enabled) + return -1; + info->reg = config->reg; + nand->ecc.mode = NAND_ECC_HW; + nand->ecc.layout = &eccoob; + + nand->options = LP_OPTIONS; + nand->cmdfunc = nand_command; + nand->read_byte = read_byte; + nand->ecc.read_page = nand_read_page_hwecc; + nand->ecc.write_page = nand_write_page_hwecc; + nand->ecc.read_page_raw = nand_read_page_raw; + nand->ecc.write_page_raw = nand_write_page_raw; + nand->ecc.read_oob = nand_read_oob; + nand->ecc.write_oob = nand_write_oob; + nand->select_chip = nand_select_chip; + nand->dev_ready = nand_dev_ready; + nand->priv = &nand_ctrl; + + /* Adjust controller clock rate */ + clock_start_periph_pll(PERIPH_ID_NDFLASH, CLOCK_ID_PERIPH, 52000000); + + /* Adjust timing for NAND device */ + setup_timing(config->timing, info->reg); + + funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_DEFAULT); + fdtdec_setup_gpio(&config->wp_gpio); + gpio_direction_output(config->wp_gpio.gpio, 1); + + our_mtd = &nand_info[devnum]; + our_mtd->priv = nand; + ret = nand_scan_ident(our_mtd, CONFIG_SYS_NAND_MAX_CHIPS, NULL); + if (ret) + return ret; + + nand->ecc.size = our_mtd->writesize; + nand->ecc.bytes = our_mtd->oobsize; + + ret = nand_scan_tail(our_mtd); + if (ret) + return ret; + + ret = nand_register(devnum); + if (ret) + return ret; + + return 0; +} + +void board_nand_init(void) +{ + struct nand_chip *nand = &nand_chip[0]; + + if (tegra_nand_init(nand, 0)) + puts("Tegra NAND init failed\n"); +} diff --git a/drivers/mtd/nand/tegra_nand.h b/drivers/mtd/nand/tegra_nand.h new file mode 100644 index 00000000000..7e74be75f81 --- /dev/null +++ b/drivers/mtd/nand/tegra_nand.h @@ -0,0 +1,257 @@ +/* + * (C) Copyright 2011 NVIDIA Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* register offset */ +#define COMMAND_0 0x00 +#define CMD_GO (1 << 31) +#define CMD_CLE (1 << 30) +#define CMD_ALE (1 << 29) +#define CMD_PIO (1 << 28) +#define CMD_TX (1 << 27) +#define CMD_RX (1 << 26) +#define CMD_SEC_CMD (1 << 25) +#define CMD_AFT_DAT_MASK (1 << 24) +#define CMD_AFT_DAT_DISABLE 0 +#define CMD_AFT_DAT_ENABLE (1 << 24) +#define CMD_TRANS_SIZE_SHIFT 20 +#define CMD_TRANS_SIZE_PAGE 8 +#define CMD_A_VALID (1 << 19) +#define CMD_B_VALID (1 << 18) +#define CMD_RD_STATUS_CHK (1 << 17) +#define CMD_R_BSY_CHK (1 << 16) +#define CMD_CE7 (1 << 15) +#define CMD_CE6 (1 << 14) +#define CMD_CE5 (1 << 13) +#define CMD_CE4 (1 << 12) +#define CMD_CE3 (1 << 11) +#define CMD_CE2 (1 << 10) +#define CMD_CE1 (1 << 9) +#define CMD_CE0 (1 << 8) +#define CMD_CLE_BYTE_SIZE_SHIFT 4 +enum { + CMD_CLE_BYTES1 = 0, + CMD_CLE_BYTES2, + CMD_CLE_BYTES3, + CMD_CLE_BYTES4, +}; +#define CMD_ALE_BYTE_SIZE_SHIFT 0 +enum { + CMD_ALE_BYTES1 = 0, + CMD_ALE_BYTES2, + CMD_ALE_BYTES3, + CMD_ALE_BYTES4, + CMD_ALE_BYTES5, + CMD_ALE_BYTES6, + CMD_ALE_BYTES7, + CMD_ALE_BYTES8 +}; + +#define STATUS_0 0x04 +#define STATUS_RBSY0 (1 << 8) + +#define ISR_0 0x08 +#define ISR_IS_CMD_DONE (1 << 5) +#define ISR_IS_ECC_ERR (1 << 4) + +#define IER_0 0x0C + +#define CFG_0 0x10 +#define CFG_HW_ECC_MASK (1 << 31) +#define CFG_HW_ECC_DISABLE 0 +#define CFG_HW_ECC_ENABLE (1 << 31) +#define CFG_HW_ECC_SEL_MASK (1 << 30) +#define CFG_HW_ECC_SEL_HAMMING 0 +#define CFG_HW_ECC_SEL_RS (1 << 30) +#define CFG_HW_ECC_CORRECTION_MASK (1 << 29) +#define CFG_HW_ECC_CORRECTION_DISABLE 0 +#define CFG_HW_ECC_CORRECTION_ENABLE (1 << 29) +#define CFG_PIPELINE_EN_MASK (1 << 28) +#define CFG_PIPELINE_EN_DISABLE 0 +#define CFG_PIPELINE_EN_ENABLE (1 << 28) +#define CFG_ECC_EN_TAG_MASK (1 << 27) +#define CFG_ECC_EN_TAG_DISABLE 0 +#define CFG_ECC_EN_TAG_ENABLE (1 << 27) +#define CFG_TVALUE_MASK (3 << 24) +enum { + CFG_TVAL4 = 0 << 24, + CFG_TVAL6 = 1 << 24, + CFG_TVAL8 = 2 << 24 +}; +#define CFG_SKIP_SPARE_MASK (1 << 23) +#define CFG_SKIP_SPARE_DISABLE 0 +#define CFG_SKIP_SPARE_ENABLE (1 << 23) +#define CFG_COM_BSY_MASK (1 << 22) +#define CFG_COM_BSY_DISABLE 0 +#define CFG_COM_BSY_ENABLE (1 << 22) +#define CFG_BUS_WIDTH_MASK (1 << 21) +#define CFG_BUS_WIDTH_8BIT 0 +#define CFG_BUS_WIDTH_16BIT (1 << 21) +#define CFG_LPDDR1_MODE_MASK (1 << 20) +#define CFG_LPDDR1_MODE_DISABLE 0 +#define CFG_LPDDR1_MODE_ENABLE (1 << 20) +#define CFG_EDO_MODE_MASK (1 << 19) +#define CFG_EDO_MODE_DISABLE 0 +#define CFG_EDO_MODE_ENABLE (1 << 19) +#define CFG_PAGE_SIZE_SEL_MASK (7 << 16) +enum { + CFG_PAGE_SIZE_256 = 0 << 16, + CFG_PAGE_SIZE_512 = 1 << 16, + CFG_PAGE_SIZE_1024 = 2 << 16, + CFG_PAGE_SIZE_2048 = 3 << 16, + CFG_PAGE_SIZE_4096 = 4 << 16 +}; +#define CFG_SKIP_SPARE_SEL_MASK (3 << 14) +enum { + CFG_SKIP_SPARE_SEL_4 = 0 << 14, + CFG_SKIP_SPARE_SEL_8 = 1 << 14, + CFG_SKIP_SPARE_SEL_12 = 2 << 14, + CFG_SKIP_SPARE_SEL_16 = 3 << 14 +}; +#define CFG_TAG_BYTE_SIZE_MASK 0x1FF + +#define TIMING_0 0x14 +#define TIMING_TRP_RESP_CNT_SHIFT 28 +#define TIMING_TRP_RESP_CNT_MASK (0xf << TIMING_TRP_RESP_CNT_SHIFT) +#define TIMING_TWB_CNT_SHIFT 24 +#define TIMING_TWB_CNT_MASK (0xf << TIMING_TWB_CNT_SHIFT) +#define TIMING_TCR_TAR_TRR_CNT_SHIFT 20 +#define TIMING_TCR_TAR_TRR_CNT_MASK (0xf << TIMING_TCR_TAR_TRR_CNT_SHIFT) +#define TIMING_TWHR_CNT_SHIFT 16 +#define TIMING_TWHR_CNT_MASK (0xf << TIMING_TWHR_CNT_SHIFT) +#define TIMING_TCS_CNT_SHIFT 14 +#define TIMING_TCS_CNT_MASK (3 << TIMING_TCS_CNT_SHIFT) +#define TIMING_TWH_CNT_SHIFT 12 +#define TIMING_TWH_CNT_MASK (3 << TIMING_TWH_CNT_SHIFT) +#define TIMING_TWP_CNT_SHIFT 8 +#define TIMING_TWP_CNT_MASK (0xf << TIMING_TWP_CNT_SHIFT) +#define TIMING_TRH_CNT_SHIFT 4 +#define TIMING_TRH_CNT_MASK (3 << TIMING_TRH_CNT_SHIFT) +#define TIMING_TRP_CNT_SHIFT 0 +#define TIMING_TRP_CNT_MASK (0xf << TIMING_TRP_CNT_SHIFT) + +#define RESP_0 0x18 + +#define TIMING2_0 0x1C +#define TIMING2_TADL_CNT_SHIFT 0 +#define TIMING2_TADL_CNT_MASK (0xf << TIMING2_TADL_CNT_SHIFT) + +#define CMD_REG1_0 0x20 +#define CMD_REG2_0 0x24 +#define ADDR_REG1_0 0x28 +#define ADDR_REG2_0 0x2C + +#define DMA_MST_CTRL_0 0x30 +#define DMA_MST_CTRL_GO_MASK (1 << 31) +#define DMA_MST_CTRL_GO_DISABLE 0 +#define DMA_MST_CTRL_GO_ENABLE (1 << 31) +#define DMA_MST_CTRL_DIR_MASK (1 << 30) +#define DMA_MST_CTRL_DIR_READ 0 +#define DMA_MST_CTRL_DIR_WRITE (1 << 30) +#define DMA_MST_CTRL_PERF_EN_MASK (1 << 29) +#define DMA_MST_CTRL_PERF_EN_DISABLE 0 +#define DMA_MST_CTRL_PERF_EN_ENABLE (1 << 29) +#define DMA_MST_CTRL_REUSE_BUFFER_MASK (1 << 27) +#define DMA_MST_CTRL_REUSE_BUFFER_DISABLE 0 +#define DMA_MST_CTRL_REUSE_BUFFER_ENABLE (1 << 27) +#define DMA_MST_CTRL_BURST_SIZE_SHIFT 24 +#define DMA_MST_CTRL_BURST_SIZE_MASK (7 << DMA_MST_CTRL_BURST_SIZE_SHIFT) +enum { + DMA_MST_CTRL_BURST_1WORDS = 2 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_4WORDS = 3 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_8WORDS = 4 << DMA_MST_CTRL_BURST_SIZE_SHIFT, + DMA_MST_CTRL_BURST_16WORDS = 5 << DMA_MST_CTRL_BURST_SIZE_SHIFT +}; +#define DMA_MST_CTRL_IS_DMA_DONE (1 << 20) +#define DMA_MST_CTRL_EN_A_MASK (1 << 2) +#define DMA_MST_CTRL_EN_A_DISABLE 0 +#define DMA_MST_CTRL_EN_A_ENABLE (1 << 2) +#define DMA_MST_CTRL_EN_B_MASK (1 << 1) +#define DMA_MST_CTRL_EN_B_DISABLE 0 +#define DMA_MST_CTRL_EN_B_ENABLE (1 << 1) + +#define DMA_CFG_A_0 0x34 +#define DMA_CFG_B_0 0x38 +#define FIFO_CTRL_0 0x3C +#define DATA_BLOCK_PTR_0 0x40 +#define TAG_PTR_0 0x44 +#define ECC_PTR_0 0x48 + +#define DEC_STATUS_0 0x4C +#define DEC_STATUS_A_ECC_FAIL (1 << 1) +#define DEC_STATUS_B_ECC_FAIL (1 << 0) + +#define BCH_CONFIG_0 0xCC +#define BCH_CONFIG_BCH_TVALUE_SHIFT 4 +#define BCH_CONFIG_BCH_TVALUE_MASK (3 << BCH_CONFIG_BCH_TVALUE_SHIFT) +enum { + BCH_CONFIG_BCH_TVAL4 = 0 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL8 = 1 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL14 = 2 << BCH_CONFIG_BCH_TVALUE_SHIFT, + BCH_CONFIG_BCH_TVAL16 = 3 << BCH_CONFIG_BCH_TVALUE_SHIFT +}; +#define BCH_CONFIG_BCH_ECC_MASK (1 << 0) +#define BCH_CONFIG_BCH_ECC_DISABLE 0 +#define BCH_CONFIG_BCH_ECC_ENABLE (1 << 0) + +#define BCH_DEC_RESULT_0 0xD0 +#define BCH_DEC_RESULT_CORRFAIL_ERR_MASK (1 << 8) +#define BCH_DEC_RESULT_PAGE_COUNT_MASK 0xFF + +#define BCH_DEC_STATUS_BUF_0 0xD4 +#define BCH_DEC_STATUS_FAIL_SEC_FLAG_MASK 0xFF000000 +#define BCH_DEC_STATUS_CORR_SEC_FLAG_MASK 0x00FF0000 +#define BCH_DEC_STATUS_FAIL_TAG_MASK (1 << 14) +#define BCH_DEC_STATUS_CORR_TAG_MASK (1 << 13) +#define BCH_DEC_STATUS_MAX_CORR_CNT_MASK (0x1f << 8) +#define BCH_DEC_STATUS_PAGE_NUMBER_MASK 0xFF + +#define LP_OPTIONS (NAND_NO_READRDY | NAND_NO_AUTOINCR) + +struct nand_ctlr { + u32 command; /* offset 00h */ + u32 status; /* offset 04h */ + u32 isr; /* offset 08h */ + u32 ier; /* offset 0Ch */ + u32 config; /* offset 10h */ + u32 timing; /* offset 14h */ + u32 resp; /* offset 18h */ + u32 timing2; /* offset 1Ch */ + u32 cmd_reg1; /* offset 20h */ + u32 cmd_reg2; /* offset 24h */ + u32 addr_reg1; /* offset 28h */ + u32 addr_reg2; /* offset 2Ch */ + u32 dma_mst_ctrl; /* offset 30h */ + u32 dma_cfg_a; /* offset 34h */ + u32 dma_cfg_b; /* offset 38h */ + u32 fifo_ctrl; /* offset 3Ch */ + u32 data_block_ptr; /* offset 40h */ + u32 tag_ptr; /* offset 44h */ + u32 resv1; /* offset 48h */ + u32 dec_status; /* offset 4Ch */ + u32 hwstatus_cmd; /* offset 50h */ + u32 hwstatus_mask; /* offset 54h */ + u32 resv2[29]; + u32 bch_config; /* offset CCh */ + u32 bch_dec_result; /* offset D0h */ + u32 bch_dec_status_buf; + /* offset D4h */ +}; diff --git a/include/fdtdec.h b/include/fdtdec.h index a8f783ffd50..474a4b90efe 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -63,6 +63,7 @@ enum fdt_compat_id { COMPAT_NVIDIA_TEGRA20_EMC, /* Tegra20 memory controller */ COMPAT_NVIDIA_TEGRA20_EMC_TABLE, /* Tegra20 memory timing table */ COMPAT_NVIDIA_TEGRA20_KBC, /* Tegra20 Keyboard */ + COMPAT_NVIDIA_TEGRA20_NAND, /* Tegra2 NAND controller */ COMPAT_COUNT, }; diff --git a/lib/fdtdec.c b/lib/fdtdec.c index af17ac1b7a1..69c63db4beb 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -42,6 +42,7 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(NVIDIA_TEGRA20_EMC, "nvidia,tegra20-emc"), COMPAT(NVIDIA_TEGRA20_EMC_TABLE, "nvidia,tegra20-emc-table"), COMPAT(NVIDIA_TEGRA20_KBC, "nvidia,tegra20-kbc"), + COMPAT(NVIDIA_TEGRA20_NAND, "nvidia,tegra20-nand"), }; const char *fdtdec_get_compatible(enum fdt_compat_id id) -- cgit v1.3.1 From 0dd84084deef226b9992b6db649b5f41d60b77b8 Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Sun, 29 Jul 2012 20:53:30 +0000 Subject: tegra: Enable NAND on Seaboard This enables NAND support for the Seaboard. Signed-off-by: Simon Glass Signed-off-by: Tom Warren --- include/configs/seaboard.h | 9 +++++++++ include/configs/tegra20-common.h | 2 ++ 2 files changed, 11 insertions(+) (limited to 'include') diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index afc4a855bf0..479af1ac6b3 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -105,4 +105,13 @@ #include "tegra20-common-post.h" +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND + +/* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +/* Somewhat oddly, the NAND base address must be a config option */ +#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE #endif /* __CONFIG_H */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 4c02f205437..02cf0cdc14c 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -201,4 +201,6 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/tegra20/u-boot-spl.lds" +#define CONFIG_SYS_NAND_SELF_INIT + #endif /* __TEGRA20_COMMON_H */ -- cgit v1.3.1 From 9614a1e9636976add95730c2da569ac1b274f232 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Mon, 30 Jul 2012 07:37:52 +0000 Subject: tegra: enable NAND on Harmony Signed-off-by: Stephen Warren Signed-off-by: Tom Warren --- board/nvidia/dts/tegra20-harmony.dts | 10 ++++++++++ include/configs/harmony.h | 11 +++++++++-- 2 files changed, 19 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/board/nvidia/dts/tegra20-harmony.dts b/board/nvidia/dts/tegra20-harmony.dts index c3519543011..ca5facb7fe7 100644 --- a/board/nvidia/dts/tegra20-harmony.dts +++ b/board/nvidia/dts/tegra20-harmony.dts @@ -54,4 +54,14 @@ usb@c5004000 { status = "disabled"; }; + + nand-controller@70008000 { + nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */ + nvidia,width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; + }; }; diff --git a/include/configs/harmony.h b/include/configs/harmony.h index d0555c16300..69857dd5810 100644 --- a/include/configs/harmony.h +++ b/include/configs/harmony.h @@ -62,8 +62,15 @@ #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT -/* Environment not stored */ -#define CONFIG_ENV_IS_NOWHERE +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE + +/* Environment in NAND (which is 512M), aligned to start of last sector */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sector size */ /* USB Host support */ #define CONFIG_USB_EHCI -- cgit v1.3.1 From 0bc069b2e46ec673daf1c17ee86099fef7252660 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Mon, 30 Jul 2012 20:21:56 +0000 Subject: tegra: Enable NAND on TEC This commit enables NAND support on the Tamonten Evaluation Carrier and adds the corresponding device tree nodes. Furthermore, the U-Boot environment can now be stored in NAND. Signed-off-by: Thierry Reding Signed-off-by: Tom Warren --- board/avionic-design/dts/tegra20-tec.dts | 11 +++++++++++ include/configs/tec.h | 12 ++++++++++-- 2 files changed, 21 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/board/avionic-design/dts/tegra20-tec.dts b/board/avionic-design/dts/tegra20-tec.dts index 9faebd8bc66..bb3851b57d1 100644 --- a/board/avionic-design/dts/tegra20-tec.dts +++ b/board/avionic-design/dts/tegra20-tec.dts @@ -55,4 +55,15 @@ usb@c5004000 { status = "disabled"; }; + + nand-controller@70008000 { + nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */ + nvidia,width = <8>; + nvidia,timing = <26 100 20 80 20 10 12 10 70>; + + nand@0 { + reg = <0>; + compatible = "hynix,hy27uf4g2b", "nand-flash"; + }; + }; }; diff --git a/include/configs/tec.h b/include/configs/tec.h index 9b3f88dff86..9d14d15f693 100644 --- a/include/configs/tec.h +++ b/include/configs/tec.h @@ -45,14 +45,22 @@ #define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ENV_IS_NOWHERE - /* SD/MMC */ #define CONFIG_MMC #define CONFIG_GENERIC_MMC #define CONFIG_TEGRA_MMC #define CONFIG_CMD_MMC +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_TEGRA_NAND +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE + +/* Environment in NAND, aligned to start of last sector */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */ + /* USB host support */ #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_TEGRA -- cgit v1.3.1 From 29159057a168fce0fb473b7771bb4f0940527213 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Mon, 30 Jul 2012 10:55:43 +0000 Subject: mmc: detect boot sectors using EXT_CSD_BOOT_MULT too Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set. Note that the Linux kernel enables access to boot partitions solely based on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only influences access to "general" partitions. eMMC devices affected by this issue exist on various NVIDIA Tegra platforms (and presumably many others too), such as Harmony (plug-in eMMC), Seaboard, Springbank, and Whistler (plug-in eMMC). Signed-off-by: Stephen Warren Signed-off-by: Tom Warren --- drivers/mmc/mmc.c | 3 ++- include/mmc.h | 1 + 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index c1c28629864..551d6a9189e 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -1162,7 +1162,8 @@ int mmc_startup(struct mmc *mmc) } /* store the partition info of emmc */ - if (ext_csd[EXT_CSD_PARTITIONING_SUPPORT] & PART_SUPPORT) + if ((ext_csd[EXT_CSD_PARTITIONING_SUPPORT] & PART_SUPPORT) || + ext_csd[EXT_CSD_BOOT_MULT]) mmc->part_config = ext_csd[EXT_CSD_PART_CONF]; } diff --git a/include/mmc.h b/include/mmc.h index 7546b4a6c82..b63b2c32a09 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -160,6 +160,7 @@ #define EXT_CSD_CARD_TYPE 196 /* RO */ #define EXT_CSD_SEC_CNT 212 /* RO, 4 bytes */ #define EXT_CSD_HC_ERASE_GRP_SIZE 224 /* RO */ +#define EXT_CSD_BOOT_MULT 226 /* RO */ /* * EXT_CSD field definitions -- cgit v1.3.1 From 573668a24e3e4ed5667332ea656e35021767ea6d Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Mon, 30 Jul 2012 10:55:45 +0000 Subject: tegra: put eMMC environment into the boot sectors When I set up Tegra's config files to put the environment into eMMC, I assumed that CONFIG_ENV_OFFSET was a linearized address relative to the start of the eMMC device, and spanning HW partitions boot0, boot1, general* and the user area in order. However, it turns out that the offset is actually relative to the beginning of the user area. Hence, the environment block ended up in a different location to expected and documented. Set CONFIG_SYS_MMC_ENV_PART=2 (boot1) to solve this, and adjust CONFIG_ENV_OFFSET to be relative to the start of boot1, not the entire eMMC. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren --- include/configs/paz00.h | 3 ++- include/configs/seaboard.h | 3 ++- include/configs/ventana.h | 3 ++- include/configs/whistler.h | 3 ++- 4 files changed, 8 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/paz00.h b/include/configs/paz00.h index 0eb9f3b6045..99b8753c586 100644 --- a/include/configs/paz00.h +++ b/include/configs/paz00.h @@ -51,8 +51,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 1024 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((1024 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index 479af1ac6b3..69965021edf 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -77,8 +77,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 512 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((512 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI diff --git a/include/configs/ventana.h b/include/configs/ventana.h index 25ec2ebfec7..f5e1bf81ff1 100644 --- a/include/configs/ventana.h +++ b/include/configs/ventana.h @@ -58,8 +58,9 @@ /* Environment in eMMC, at the end of 2nd "boot sector" */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 1024 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((1024 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI diff --git a/include/configs/whistler.h b/include/configs/whistler.h index b747d0e2b2c..32357181556 100644 --- a/include/configs/whistler.h +++ b/include/configs/whistler.h @@ -72,8 +72,9 @@ * particular card is standard practice as far as I know. */ #define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET ((2 * 512 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_ENV_OFFSET ((512 * 1024) - CONFIG_ENV_SIZE) #define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 2 /* USB Host support */ #define CONFIG_USB_EHCI -- cgit v1.3.1 From b85705e60ec0f5ce2638ccf27a802e8df1a8d57c Mon Sep 17 00:00:00 2001 From: Ashok Kumar Reddy Date: Wed, 5 Sep 2012 22:09:37 +0530 Subject: ima3-mx53:Rename CONFIG_PRIME => CONFIG_ETHPRME, remove unused macro CONFIG_DISCOVER_PHY Signed-off-by: Ashok Kumar Reddy Acked-by: Stefano Babic --- include/configs/ima3-mx53.h | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/ima3-mx53.h b/include/configs/ima3-mx53.h index 567061aee30..dbc59b91e98 100644 --- a/include/configs/ima3-mx53.h +++ b/include/configs/ima3-mx53.h @@ -64,7 +64,6 @@ /* Ethernet on FEC */ #define CONFIG_NET_MULTI #define CONFIG_MII -#define CONFIG_DISCOVER_PHY #define CONFIG_FEC_MXC #define IMX_FEC_BASE FEC_BASE_ADDR @@ -72,7 +71,7 @@ #define CONFIG_PHY_ADDR CONFIG_FEC_MXC_PHYADDR #define CONFIG_RESET_PHY_R #define CONFIG_FEC_MXC_NO_ANEG -#define CONFIG_PRIME "FEC0" +#define CONFIG_ETHPRIME "FEC0" /* SPI */ #define CONFIG_HARD_SPI -- cgit v1.3.1 From 3292539e7dc347c2d8a8f307b3a1ffa67ca1d4fe Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Wed, 5 Sep 2012 21:47:42 +0000 Subject: MX35: mx35pdk: add support for MMC Add support for SD card and change the default environment due to increased u-boot size. Signed-off-by: Stefano Babic --- board/freescale/mx35pdk/mx35pdk.c | 25 +++++++++++++++++++++++++ include/configs/mx35pdk.h | 17 +++++++++++++++-- 2 files changed, 40 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/board/freescale/mx35pdk/mx35pdk.c b/board/freescale/mx35pdk/mx35pdk.c index 787c9232d25..7cb6b3086f1 100644 --- a/board/freescale/mx35pdk/mx35pdk.c +++ b/board/freescale/mx35pdk/mx35pdk.c @@ -32,6 +32,8 @@ #include #include #include +#include +#include #include #include #include @@ -275,3 +277,26 @@ int board_eth_init(bd_t *bis) return rc; } + +#if defined(CONFIG_FSL_ESDHC) + +struct fsl_esdhc_cfg esdhc_cfg = {MMC_SDHC1_BASE_ADDR}; + +int board_mmc_init(bd_t *bis) +{ + /* configure pins for SDHC1 only */ + mxc_request_iomux(MX35_PIN_SD1_CMD, MUX_CONFIG_FUNC); + mxc_request_iomux(MX35_PIN_SD1_CLK, MUX_CONFIG_FUNC); + mxc_request_iomux(MX35_PIN_SD1_DATA0, MUX_CONFIG_FUNC); + mxc_request_iomux(MX35_PIN_SD1_DATA1, MUX_CONFIG_FUNC); + mxc_request_iomux(MX35_PIN_SD1_DATA2, MUX_CONFIG_FUNC); + mxc_request_iomux(MX35_PIN_SD1_DATA3, MUX_CONFIG_FUNC); + + return fsl_esdhc_initialize(bis, &esdhc_cfg); +} + +int board_mmc_getcd(struct mmc *mmc) +{ + return !(mc9sdz60_reg_read(MC9SDZ60_REG_DES_FLAG) & 0x4); +} +#endif diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h index 834b97da778..38b15465843 100644 --- a/include/configs/mx35pdk.h +++ b/include/configs/mx35pdk.h @@ -110,6 +110,12 @@ #define CONFIG_NET_RETRY_COUNT 100 #define CONFIG_CMD_DATE +#define CONFIG_CMD_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT + #define CONFIG_BOOTDELAY 3 #define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */ @@ -237,6 +243,13 @@ #define CONFIG_MXC_NAND_HWECC #define CONFIG_SYS_NAND_LARGEPAGE +/* mmc driver */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_ESDHC_NUM 1 + /* * Default environment and default scripts * to update uboot and load kernel @@ -278,8 +291,8 @@ "u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ "load=tftp ${loadaddr} ${u-boot}\0" \ "uboot_addr=" xstr(CONFIG_SYS_MONITOR_BASE) "\0" \ - "update=protect off ${uboot_addr} +40000;" \ - "erase ${uboot_addr} +40000;" \ + "update=protect off ${uboot_addr} +80000;" \ + "erase ${uboot_addr} +80000;" \ "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \ "upd=if run load;then echo Updating u-boot;if run update;" \ "then echo U-Boot updated;" \ -- cgit v1.3.1 From 29f3e3f24832fccdd7ce5fa961bc4d4005b07381 Mon Sep 17 00:00:00 2001 From: Tom Warren Date: Tue, 4 Sep 2012 17:00:24 -0700 Subject: Tegra: Change Tegra20 to Tegra in common code, prep for T30 Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate. Convert tegra20_ source file and function names to tegra_, also. Upcoming Tegra30 port will use common code/defines/names where possible. Signed-off-by: Tom Warren Acked-by: Stephen Warren --- arch/arm/cpu/arm720t/tegra20/cpu.c | 8 +- arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c | 2 +- arch/arm/cpu/tegra20-common/Makefile | 2 +- arch/arm/cpu/tegra20-common/ap20.c | 6 +- arch/arm/cpu/tegra20-common/board.c | 14 +- arch/arm/cpu/tegra20-common/warmboot.c | 14 +- arch/arm/cpu/tegra20-common/warmboot_avp.c | 2 +- arch/arm/include/asm/arch-tegra20/ap20.h | 3 - arch/arm/include/asm/arch-tegra20/mmc.h | 8 +- arch/arm/include/asm/arch-tegra20/sys_proto.h | 4 +- arch/arm/include/asm/arch-tegra20/tegra20.h | 14 +- arch/arm/include/asm/arch-tegra20/tegra_mmc.h | 131 ++++++++++++++++ arch/arm/include/asm/arch-tegra20/tegra_spi.h | 2 +- arch/arm/include/asm/arch-tegra20/timer.h | 4 +- board/avionic-design/common/tamonten.c | 2 +- board/compal/paz00/paz00.c | 4 +- board/compulab/trimslice/trimslice.c | 4 +- board/nvidia/common/board.c | 8 +- board/nvidia/harmony/harmony.c | 4 +- board/nvidia/seaboard/seaboard.c | 4 +- board/nvidia/whistler/whistler.c | 4 +- drivers/gpio/tegra_gpio.c | 8 +- drivers/i2c/tegra_i2c.c | 12 +- drivers/input/Makefile | 2 +- drivers/mmc/tegra_mmc.c | 34 ++-- drivers/mmc/tegra_mmc.h | 131 ---------------- drivers/spi/tegra_spi.c | 6 +- include/configs/harmony.h | 10 +- include/configs/medcom.h | 6 +- include/configs/paz00.h | 6 +- include/configs/plutux.h | 6 +- include/configs/seaboard.h | 20 +-- include/configs/tec.h | 8 +- include/configs/tegra-common-post.h | 214 ++++++++++++++++++++++++++ include/configs/tegra20-common-post.h | 214 -------------------------- include/configs/tegra20-common.h | 12 +- include/configs/trimslice.h | 8 +- include/configs/ventana.h | 6 +- include/configs/whistler.h | 8 +- 39 files changed, 476 insertions(+), 479 deletions(-) create mode 100644 arch/arm/include/asm/arch-tegra20/tegra_mmc.h delete mode 100644 drivers/mmc/tegra_mmc.h create mode 100644 include/configs/tegra-common-post.h delete mode 100644 include/configs/tegra20-common-post.h (limited to 'include') diff --git a/arch/arm/cpu/arm720t/tegra20/cpu.c b/arch/arm/cpu/arm720t/tegra20/cpu.c index 6d4d66bced0..ddf8d979f44 100644 --- a/arch/arm/cpu/arm720t/tegra20/cpu.c +++ b/arch/arm/cpu/arm720t/tegra20/cpu.c @@ -105,14 +105,14 @@ static void enable_cpu_clock(int enable) static int is_cpu_powered(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; return (readl(&pmc->pmc_pwrgate_status) & CPU_PWRED) ? 1 : 0; } static void remove_cpu_io_clamps(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; /* Remove the clamps on the CPU I/O signals */ @@ -126,7 +126,7 @@ static void remove_cpu_io_clamps(void) static void powerup_cpu(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; int timeout = IO_STABILIZATION_DELAY; @@ -157,7 +157,7 @@ static void powerup_cpu(void) static void enable_cpu_power_rail(void) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; reg = readl(&pmc->pmc_cntrl); diff --git a/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c b/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c index 75cadb03ec7..925f8414c4d 100644 --- a/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c +++ b/arch/arm/cpu/armv7/tegra20/cmd_enterrcm.c @@ -46,7 +46,7 @@ static int do_enterrcm(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; puts("Entering RCM...\n"); udelay(50000); diff --git a/arch/arm/cpu/tegra20-common/Makefile b/arch/arm/cpu/tegra20-common/Makefile index 43c96c68643..9e91e5cb8ca 100644 --- a/arch/arm/cpu/tegra20-common/Makefile +++ b/arch/arm/cpu/tegra20-common/Makefile @@ -33,7 +33,7 @@ LIB = $(obj)lib$(SOC)-common.o SOBJS += lowlevel_init.o COBJS-y += ap20.o board.o clock.o funcmux.o pinmux.o sys_info.o timer.o -COBJS-$(CONFIG_TEGRA20_LP0) += warmboot.o crypto.o warmboot_avp.o +COBJS-$(CONFIG_TEGRA_LP0) += warmboot.o crypto.o warmboot_avp.o COBJS-$(CONFIG_TEGRA_CLOCK_SCALING) += emc.o COBJS-$(CONFIG_TEGRA_PMU) += pmu.o diff --git a/arch/arm/cpu/tegra20-common/ap20.c b/arch/arm/cpu/tegra20-common/ap20.c index 00588dae527..c0ca6eb379e 100644 --- a/arch/arm/cpu/tegra20-common/ap20.c +++ b/arch/arm/cpu/tegra20-common/ap20.c @@ -32,7 +32,7 @@ int tegra_get_chip_type(void) { struct apb_misc_gp_ctlr *gp; - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; uint tegra_sku_id, rev; /* @@ -40,7 +40,7 @@ int tegra_get_chip_type(void) * APB_MISC + 0x804, and has value 0x20 for Tegra20, 0x30 for * Tegra30 */ - gp = (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + gp = (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; rev = (readl(&gp->hidrev) & HIDREV_CHIPID_MASK) >> HIDREV_CHIPID_SHIFT; tegra_sku_id = readl(&fuse->sku_info) & 0xff; @@ -101,7 +101,7 @@ static u32 get_odmdata(void) static void init_pmc_scratch(void) { - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 odmdata; int i; diff --git a/arch/arm/cpu/tegra20-common/board.c b/arch/arm/cpu/tegra20-common/board.c index 598023aba9a..8a8d3384ac4 100644 --- a/arch/arm/cpu/tegra20-common/board.c +++ b/arch/arm/cpu/tegra20-common/board.c @@ -47,7 +47,7 @@ enum { unsigned int query_sdram_size(void) { - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; u32 reg; reg = readl(&pmc->pmc_scratch20); @@ -81,11 +81,11 @@ int checkboard(void) #endif /* CONFIG_DISPLAY_BOARDINFO */ static int uart_configs[] = { -#if defined(CONFIG_TEGRA20_UARTA_UAA_UAB) +#if defined(CONFIG_TEGRA_UARTA_UAA_UAB) FUNCMUX_UART1_UAA_UAB, -#elif defined(CONFIG_TEGRA20_UARTA_GPU) +#elif defined(CONFIG_TEGRA_UARTA_GPU) FUNCMUX_UART1_GPU, -#elif defined(CONFIG_TEGRA20_UARTA_SDIO1) +#elif defined(CONFIG_TEGRA_UARTA_SDIO1) FUNCMUX_UART1_SDIO1, #else FUNCMUX_UART1_IRRX_IRTX, @@ -125,13 +125,13 @@ void board_init_uart_f(void) { int uart_ids = 0; /* bit mask of which UART ids to enable */ -#ifdef CONFIG_TEGRA20_ENABLE_UARTA +#ifdef CONFIG_TEGRA_ENABLE_UARTA uart_ids |= UARTA; #endif -#ifdef CONFIG_TEGRA20_ENABLE_UARTB +#ifdef CONFIG_TEGRA_ENABLE_UARTB uart_ids |= UARTB; #endif -#ifdef CONFIG_TEGRA20_ENABLE_UARTD +#ifdef CONFIG_TEGRA_ENABLE_UARTD uart_ids |= UARTD; #endif setup_uarts(uart_ids); diff --git a/arch/arm/cpu/tegra20-common/warmboot.c b/arch/arm/cpu/tegra20-common/warmboot.c index 809ea0133eb..6ce995ef029 100644 --- a/arch/arm/cpu/tegra20-common/warmboot.c +++ b/arch/arm/cpu/tegra20-common/warmboot.c @@ -39,7 +39,7 @@ DECLARE_GLOBAL_DATA_PTR; #ifndef CONFIG_TEGRA_CLOCK_SCALING -#error "You must enable CONFIG_TEGRA_CLOCK_SCALING to use CONFIG_TEGRA20_LP0" +#error "You must enable CONFIG_TEGRA_CLOCK_SCALING to use CONFIG_TEGRA_LP0" #endif /* @@ -139,9 +139,9 @@ int warmboot_save_sdram_params(void) u32 ram_code; struct sdram_params sdram; struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE; - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; struct emc_ctlr *emc = emc_get_controller(gd->fdt_blob); union scratch2_reg scratch2; union scratch4_reg scratch4; @@ -205,7 +205,7 @@ static u32 get_major_version(void) { u32 major_id; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; major_id = (readl(&gp->hidrev) & HIDREV_MAJORPREV_MASK) >> HIDREV_MAJORPREV_SHIFT; @@ -229,7 +229,7 @@ static int is_failure_analysis_mode(struct fuse_regs *fuse) static int ap20_is_odm_production_mode(void) { - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; if (!is_failure_analysis_mode(fuse) && is_odm_production_mode_fuse_set(fuse)) @@ -240,7 +240,7 @@ static int ap20_is_odm_production_mode(void) static int ap20_is_production_mode(void) { - struct fuse_regs *fuse = (struct fuse_regs *)TEGRA20_FUSE_BASE; + struct fuse_regs *fuse = (struct fuse_regs *)NV_PA_FUSE_BASE; if (get_major_version() == 0) return 1; @@ -257,7 +257,7 @@ static enum fuse_operating_mode fuse_get_operation_mode(void) { u32 chip_id; struct apb_misc_gp_ctlr *gp = - (struct apb_misc_gp_ctlr *)TEGRA20_APB_MISC_GP_BASE; + (struct apb_misc_gp_ctlr *)NV_PA_APB_MISC_GP_BASE; chip_id = (readl(&gp->hidrev) & HIDREV_CHIPID_MASK) >> HIDREV_CHIPID_SHIFT; diff --git a/arch/arm/cpu/tegra20-common/warmboot_avp.c b/arch/arm/cpu/tegra20-common/warmboot_avp.c index cd01908a462..80a5a15decf 100644 --- a/arch/arm/cpu/tegra20-common/warmboot_avp.c +++ b/arch/arm/cpu/tegra20-common/warmboot_avp.c @@ -38,7 +38,7 @@ void wb_start(void) { struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE; - struct pmc_ctlr *pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; struct flow_ctlr *flow = (struct flow_ctlr *)NV_PA_FLOW_BASE; struct clk_rst_ctlr *clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE; diff --git a/arch/arm/include/asm/arch-tegra20/ap20.h b/arch/arm/include/asm/arch-tegra20/ap20.h index c84d22f97bd..70d94c50417 100644 --- a/arch/arm/include/asm/arch-tegra20/ap20.h +++ b/arch/arm/include/asm/arch-tegra20/ap20.h @@ -95,9 +95,6 @@ #define HALT_COP_EVENT_IRQ_1 (1 << 11) #define HALT_COP_EVENT_FIQ_1 (1 << 9) -/* Start up the tegra20 SOC */ -void tegra20_start(void); - /* This is the main entry into U-Boot, used by the Cortex-A9 */ extern void _start(void); diff --git a/arch/arm/include/asm/arch-tegra20/mmc.h b/arch/arm/include/asm/arch-tegra20/mmc.h index 916a353a97d..5c95047998c 100644 --- a/arch/arm/include/asm/arch-tegra20/mmc.h +++ b/arch/arm/include/asm/arch-tegra20/mmc.h @@ -19,9 +19,9 @@ * MA 02111-1307 USA */ -#ifndef _TEGRA20_MMC_H_ -#define _TEGRA20_MMC_H_ +#ifndef _TEGRA_MMC_H_ +#define _TEGRA_MMC_H_ -int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio); +int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio); -#endif /* TEGRA20_MMC_H_ */ +#endif /* _TEGRA_MMC_H_ */ diff --git a/arch/arm/include/asm/arch-tegra20/sys_proto.h b/arch/arm/include/asm/arch-tegra20/sys_proto.h index 643d5424b84..919aec7f74c 100644 --- a/arch/arm/include/asm/arch-tegra20/sys_proto.h +++ b/arch/arm/include/asm/arch-tegra20/sys_proto.h @@ -24,12 +24,12 @@ #ifndef _SYS_PROTO_H_ #define _SYS_PROTO_H_ -struct tegra20_sysinfo { +struct tegra_sysinfo { char *board_string; }; void invalidate_dcache(void); -extern const struct tegra20_sysinfo sysinfo; +extern const struct tegra_sysinfo sysinfo; #endif diff --git a/arch/arm/include/asm/arch-tegra20/tegra20.h b/arch/arm/include/asm/arch-tegra20/tegra20.h index b2fb50e33e7..c9485a1c844 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra20.h +++ b/arch/arm/include/asm/arch-tegra20/tegra20.h @@ -33,22 +33,22 @@ #define NV_PA_GPIO_BASE 0x6000D000 #define NV_PA_EVP_BASE 0x6000F000 #define NV_PA_APB_MISC_BASE 0x70000000 -#define TEGRA20_APB_MISC_GP_BASE (NV_PA_APB_MISC_BASE + 0x0800) +#define NV_PA_APB_MISC_GP_BASE (NV_PA_APB_MISC_BASE + 0x0800) #define NV_PA_APB_UARTA_BASE (NV_PA_APB_MISC_BASE + 0x6000) #define NV_PA_APB_UARTB_BASE (NV_PA_APB_MISC_BASE + 0x6040) #define NV_PA_APB_UARTC_BASE (NV_PA_APB_MISC_BASE + 0x6200) #define NV_PA_APB_UARTD_BASE (NV_PA_APB_MISC_BASE + 0x6300) #define NV_PA_APB_UARTE_BASE (NV_PA_APB_MISC_BASE + 0x6400) -#define TEGRA20_NAND_BASE (NV_PA_APB_MISC_BASE + 0x8000) -#define TEGRA20_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) -#define TEGRA20_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) -#define TEGRA20_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) +#define NV_PA_NAND_BASE (NV_PA_APB_MISC_BASE + 0x8000) +#define NV_PA_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) +#define NV_PA_PMC_BASE (NV_PA_APB_MISC_BASE + 0xE400) +#define NV_PA_FUSE_BASE (NV_PA_APB_MISC_BASE + 0xF800) #define NV_PA_CSITE_BASE 0x70040000 #define TEGRA_USB1_BASE 0xC5000000 #define TEGRA_USB3_BASE 0xC5008000 #define TEGRA_USB_ADDR_MASK 0xFFFFC000 -#define TEGRA20_SDRC_CS0 NV_PA_SDRAM_BASE +#define NV_PA_SDRC_CS0 NV_PA_SDRAM_BASE #define LOW_LEVEL_SRAM_STACK 0x4000FFFC #define EARLY_AVP_STACK (NV_PA_SDRAM_BASE + 0x20000) #define EARLY_CPU_STACK (EARLY_AVP_STACK - 4096) @@ -86,7 +86,7 @@ enum { }; #else /* __ASSEMBLY__ */ -#define PRM_RSTCTRL TEGRA20_PMC_BASE +#define PRM_RSTCTRL NV_PA_PMC_BASE #endif #endif /* TEGRA20_H */ diff --git a/arch/arm/include/asm/arch-tegra20/tegra_mmc.h b/arch/arm/include/asm/arch-tegra20/tegra_mmc.h new file mode 100644 index 00000000000..dd746cae0d0 --- /dev/null +++ b/arch/arm/include/asm/arch-tegra20/tegra_mmc.h @@ -0,0 +1,131 @@ +/* + * (C) Copyright 2009 SAMSUNG Electronics + * Minkyu Kang + * Portions Copyright (C) 2011-2012 NVIDIA Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#ifndef __TEGRA_MMC_H_ +#define __TEGRA_MMC_H_ + +#define TEGRA_SDMMC1_BASE 0xC8000000 +#define TEGRA_SDMMC2_BASE 0xC8000200 +#define TEGRA_SDMMC3_BASE 0xC8000400 +#define TEGRA_SDMMC4_BASE 0xC8000600 + +#ifndef __ASSEMBLY__ +struct tegra_mmc { + unsigned int sysad; /* _SYSTEM_ADDRESS_0 */ + unsigned short blksize; /* _BLOCK_SIZE_BLOCK_COUNT_0 15:00 */ + unsigned short blkcnt; /* _BLOCK_SIZE_BLOCK_COUNT_0 31:16 */ + unsigned int argument; /* _ARGUMENT_0 */ + unsigned short trnmod; /* _CMD_XFER_MODE_0 15:00 xfer mode */ + unsigned short cmdreg; /* _CMD_XFER_MODE_0 31:16 cmd reg */ + unsigned int rspreg0; /* _RESPONSE_R0_R1_0 CMD RESP 31:00 */ + unsigned int rspreg1; /* _RESPONSE_R2_R3_0 CMD RESP 63:32 */ + unsigned int rspreg2; /* _RESPONSE_R4_R5_0 CMD RESP 95:64 */ + unsigned int rspreg3; /* _RESPONSE_R6_R7_0 CMD RESP 127:96 */ + unsigned int bdata; /* _BUFFER_DATA_PORT_0 */ + unsigned int prnsts; /* _PRESENT_STATE_0 */ + unsigned char hostctl; /* _POWER_CONTROL_HOST_0 7:00 */ + unsigned char pwrcon; /* _POWER_CONTROL_HOST_0 15:8 */ + unsigned char blkgap; /* _POWER_CONTROL_HOST_9 23:16 */ + unsigned char wakcon; /* _POWER_CONTROL_HOST_0 31:24 */ + unsigned short clkcon; /* _CLOCK_CONTROL_0 15:00 */ + unsigned char timeoutcon; /* _TIMEOUT_CTRL 23:16 */ + unsigned char swrst; /* _SW_RESET_ 31:24 */ + unsigned int norintsts; /* _INTERRUPT_STATUS_0 */ + unsigned int norintstsen; /* _INTERRUPT_STATUS_ENABLE_0 */ + unsigned int norintsigen; /* _INTERRUPT_SIGNAL_ENABLE_0 */ + unsigned short acmd12errsts; /* _AUTO_CMD12_ERR_STATUS_0 15:00 */ + unsigned char res1[2]; /* _RESERVED 31:16 */ + unsigned int capareg; /* _CAPABILITIES_0 */ + unsigned char res2[4]; /* RESERVED, offset 44h-47h */ + unsigned int maxcurr; /* _MAXIMUM_CURRENT_0 */ + unsigned char res3[4]; /* RESERVED, offset 4Ch-4Fh */ + unsigned short setacmd12err; /* offset 50h */ + unsigned short setinterr; /* offset 52h */ + unsigned char admaerr; /* offset 54h */ + unsigned char res4[3]; /* RESERVED, offset 55h-57h */ + unsigned long admaaddr; /* offset 58h-5Fh */ + unsigned char res5[0x9c]; /* RESERVED, offset 60h-FBh */ + unsigned short slotintstatus; /* offset FCh */ + unsigned short hcver; /* HOST Version */ + unsigned char res6[0x100]; /* RESERVED, offset 100h-1FFh */ +}; + +#define TEGRA_MMC_HOSTCTL_DMASEL_MASK (3 << 3) +#define TEGRA_MMC_HOSTCTL_DMASEL_SDMA (0 << 3) +#define TEGRA_MMC_HOSTCTL_DMASEL_ADMA2_32BIT (2 << 3) +#define TEGRA_MMC_HOSTCTL_DMASEL_ADMA2_64BIT (3 << 3) + +#define TEGRA_MMC_TRNMOD_DMA_ENABLE (1 << 0) +#define TEGRA_MMC_TRNMOD_BLOCK_COUNT_ENABLE (1 << 1) +#define TEGRA_MMC_TRNMOD_DATA_XFER_DIR_SEL_WRITE (0 << 4) +#define TEGRA_MMC_TRNMOD_DATA_XFER_DIR_SEL_READ (1 << 4) +#define TEGRA_MMC_TRNMOD_MULTI_BLOCK_SELECT (1 << 5) + +#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_MASK (3 << 0) +#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_NO_RESPONSE (0 << 0) +#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_136 (1 << 0) +#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48 (2 << 0) +#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48_BUSY (3 << 0) + +#define TEGRA_MMC_TRNMOD_CMD_CRC_CHECK (1 << 3) +#define TEGRA_MMC_TRNMOD_CMD_INDEX_CHECK (1 << 4) +#define TEGRA_MMC_TRNMOD_DATA_PRESENT_SELECT_DATA_TRANSFER (1 << 5) + +#define TEGRA_MMC_PRNSTS_CMD_INHIBIT_CMD (1 << 0) +#define TEGRA_MMC_PRNSTS_CMD_INHIBIT_DAT (1 << 1) + +#define TEGRA_MMC_CLKCON_INTERNAL_CLOCK_ENABLE (1 << 0) +#define TEGRA_MMC_CLKCON_INTERNAL_CLOCK_STABLE (1 << 1) +#define TEGRA_MMC_CLKCON_SD_CLOCK_ENABLE (1 << 2) + +#define TEGRA_MMC_CLKCON_SDCLK_FREQ_SEL_SHIFT 8 +#define TEGRA_MMC_CLKCON_SDCLK_FREQ_SEL_MASK (0xff << 8) + +#define TEGRA_MMC_SWRST_SW_RESET_FOR_ALL (1 << 0) +#define TEGRA_MMC_SWRST_SW_RESET_FOR_CMD_LINE (1 << 1) +#define TEGRA_MMC_SWRST_SW_RESET_FOR_DAT_LINE (1 << 2) + +#define TEGRA_MMC_NORINTSTS_CMD_COMPLETE (1 << 0) +#define TEGRA_MMC_NORINTSTS_XFER_COMPLETE (1 << 1) +#define TEGRA_MMC_NORINTSTS_DMA_INTERRUPT (1 << 3) +#define TEGRA_MMC_NORINTSTS_ERR_INTERRUPT (1 << 15) +#define TEGRA_MMC_NORINTSTS_CMD_TIMEOUT (1 << 16) + +#define TEGRA_MMC_NORINTSTSEN_CMD_COMPLETE (1 << 0) +#define TEGRA_MMC_NORINTSTSEN_XFER_COMPLETE (1 << 1) +#define TEGRA_MMC_NORINTSTSEN_DMA_INTERRUPT (1 << 3) +#define TEGRA_MMC_NORINTSTSEN_BUFFER_WRITE_READY (1 << 4) +#define TEGRA_MMC_NORINTSTSEN_BUFFER_READ_READY (1 << 5) + +#define TEGRA_MMC_NORINTSIGEN_XFER_COMPLETE (1 << 1) + +struct mmc_host { + struct tegra_mmc *reg; + unsigned int version; /* SDHCI spec. version */ + unsigned int clock; /* Current clock (MHz) */ + unsigned int base; /* Base address, SDMMC1/2/3/4 */ + enum periph_id mmc_id; /* Peripheral ID: PERIPH_ID_... */ + int pwr_gpio; /* Power GPIO */ + int cd_gpio; /* Change Detect GPIO */ +}; + +#endif /* __ASSEMBLY__ */ +#endif /* __TEGRA_MMC_H_ */ diff --git a/arch/arm/include/asm/arch-tegra20/tegra_spi.h b/arch/arm/include/asm/arch-tegra20/tegra_spi.h index 8978beacc5d..d53a93ff53a 100644 --- a/arch/arm/include/asm/arch-tegra20/tegra_spi.h +++ b/arch/arm/include/asm/arch-tegra20/tegra_spi.h @@ -70,6 +70,6 @@ struct spi_tegra { #define SPI_STAT_CUR_BLKCNT (1 << 15) #define SPI_TIMEOUT 1000 -#define TEGRA20_SPI_MAX_FREQ 52000000 +#define TEGRA_SPI_MAX_FREQ 52000000 #endif /* _TEGRA_SPI_H_ */ diff --git a/arch/arm/include/asm/arch-tegra20/timer.h b/arch/arm/include/asm/arch-tegra20/timer.h index 43f7ab4efa6..fdb99a73eeb 100644 --- a/arch/arm/include/asm/arch-tegra20/timer.h +++ b/arch/arm/include/asm/arch-tegra20/timer.h @@ -21,8 +21,8 @@ /* Tegra20 timer functions */ -#ifndef _TEGRA20_TIMER_H -#define _TEGRA20_TIMER_H +#ifndef _TEGRA_TIMER_H +#define _TEGRA_TIMER_H /* returns the current monotonic timer value in microseconds */ unsigned long timer_get_us(void); diff --git a/board/avionic-design/common/tamonten.c b/board/avionic-design/common/tamonten.c index a0a4d1d07dd..93f12ea4f19 100644 --- a/board/avionic-design/common/tamonten.c +++ b/board/avionic-design/common/tamonten.c @@ -78,7 +78,7 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0, SD slot, with 4-bit bus */ - tegra20_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); + tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); return 0; } diff --git a/board/compal/paz00/paz00.c b/board/compal/paz00/paz00.c index cd684f29263..0f8f1670172 100644 --- a/board/compal/paz00/paz00.c +++ b/board/compal/paz00/paz00.c @@ -70,11 +70,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init eMMC\n"); /* init dev 0, eMMC chip, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, -1, -1); + tegra_mmc_init(0, 4, -1, -1); debug("board_mmc_init: init SD slot\n"); /* init dev 3, SD slot, with 4-bit bus */ - tegra20_mmc_init(3, 4, GPIO_PV1, GPIO_PV5); + tegra_mmc_init(3, 4, GPIO_PV1, GPIO_PV5); return 0; } diff --git a/board/compulab/trimslice/trimslice.c b/board/compulab/trimslice/trimslice.c index 5dae15b962f..893cca8c19b 100644 --- a/board/compulab/trimslice/trimslice.c +++ b/board/compulab/trimslice/trimslice.c @@ -69,10 +69,10 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0 (SDMMC4), (micro-SD slot) with 4-bit bus */ - tegra20_mmc_init(0, 4, -1, GPIO_PP1); + tegra_mmc_init(0, 4, -1, GPIO_PP1); /* init dev 3 (SDMMC1), (SD slot) with 4-bit bus */ - tegra20_mmc_init(3, 4, -1, -1); + tegra_mmc_init(3, 4, -1, -1); return 0; } diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c index 7ab20408e86..afe832a5295 100644 --- a/board/nvidia/common/board.c +++ b/board/nvidia/common/board.c @@ -45,8 +45,8 @@ DECLARE_GLOBAL_DATA_PTR; -const struct tegra20_sysinfo sysinfo = { - CONFIG_TEGRA20_BOARD_STRING +const struct tegra_sysinfo sysinfo = { + CONFIG_TEGRA_BOARD_STRING }; #ifndef CONFIG_SPL_BUILD @@ -79,7 +79,7 @@ void pin_mux_spi(void) __attribute__((weak, alias("__pin_mux_spi"))); static void power_det_init(void) { #if defined(CONFIG_TEGRA20) - struct pmc_ctlr *const pmc = (struct pmc_ctlr *)TEGRA20_PMC_BASE; + struct pmc_ctlr *const pmc = (struct pmc_ctlr *)NV_PA_PMC_BASE; /* turn off power detects */ writel(0, &pmc->pmc_pwr_det_latch); @@ -132,7 +132,7 @@ int board_init(void) board_usb_init(gd->fdt_blob); #endif -#ifdef CONFIG_TEGRA20_LP0 +#ifdef CONFIG_TEGRA_LP0 /* save Sdram params to PMC 2, 4, and 24 for WB0 */ warmboot_save_sdram_params(); diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c index 44977c78d1d..b4a811dc5f9 100644 --- a/board/nvidia/harmony/harmony.c +++ b/board/nvidia/harmony/harmony.c @@ -73,11 +73,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init SD slot J26\n"); /* init dev 0, SD slot J26, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); + tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2); debug("board_mmc_init: init SD slot J5\n"); /* init dev 2, SD slot J5, with 4-bit bus */ - tegra20_mmc_init(2, 4, GPIO_PT3, GPIO_PI5); + tegra_mmc_init(2, 4, GPIO_PT3, GPIO_PI5); return 0; } diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c index 3298a6b3a88..667f60a9bb9 100644 --- a/board/nvidia/seaboard/seaboard.c +++ b/board/nvidia/seaboard/seaboard.c @@ -81,11 +81,11 @@ int board_mmc_init(bd_t *bd) debug("board_mmc_init: init eMMC\n"); /* init dev 0, eMMC chip, with 4-bit bus */ /* The board has an 8-bit bus, but 8-bit doesn't work yet */ - tegra20_mmc_init(0, 4, -1, -1); + tegra_mmc_init(0, 4, -1, -1); debug("board_mmc_init: init SD slot\n"); /* init dev 1, SD slot, with 4-bit bus */ - tegra20_mmc_init(1, 4, GPIO_PI6, GPIO_PI5); + tegra_mmc_init(1, 4, GPIO_PI6, GPIO_PI5); return 0; } diff --git a/board/nvidia/whistler/whistler.c b/board/nvidia/whistler/whistler.c index c0a114d6677..598b2e5ce25 100644 --- a/board/nvidia/whistler/whistler.c +++ b/board/nvidia/whistler/whistler.c @@ -81,10 +81,10 @@ int board_mmc_init(bd_t *bd) pin_mux_mmc(); /* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */ - tegra20_mmc_init(0, 8, -1, -1); + tegra_mmc_init(0, 8, -1, -1); /* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */ - tegra20_mmc_init(1, 8, -1, -1); + tegra_mmc_init(1, 8, -1, -1); return 0; } diff --git a/drivers/gpio/tegra_gpio.c b/drivers/gpio/tegra_gpio.c index 8cfcf8283b3..747f4cf9212 100644 --- a/drivers/gpio/tegra_gpio.c +++ b/drivers/gpio/tegra_gpio.c @@ -34,10 +34,10 @@ #include enum { - TEGRA20_CMD_INFO, - TEGRA20_CMD_PORT, - TEGRA20_CMD_OUTPUT, - TEGRA20_CMD_INPUT, + TEGRA_CMD_INFO, + TEGRA_CMD_PORT, + TEGRA_CMD_OUTPUT, + TEGRA_CMD_INPUT, }; static struct gpio_names { diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c index b4eb49127eb..e3be14e3cf3 100644 --- a/drivers/i2c/tegra_i2c.c +++ b/drivers/i2c/tegra_i2c.c @@ -262,7 +262,7 @@ exit: return error; } -static int tegra20_i2c_write_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_write_data(u32 addr, u8 *data, u32 len) { int error; struct i2c_trans_info trans_info; @@ -275,12 +275,12 @@ static int tegra20_i2c_write_data(u32 addr, u8 *data, u32 len) error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); if (error) - debug("tegra20_i2c_write_data: Error (%d) !!!\n", error); + debug("tegra_i2c_write_data: Error (%d) !!!\n", error); return error; } -static int tegra20_i2c_read_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_read_data(u32 addr, u8 *data, u32 len) { int error; struct i2c_trans_info trans_info; @@ -293,7 +293,7 @@ static int tegra20_i2c_read_data(u32 addr, u8 *data, u32 len) error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); if (error) - debug("tegra20_i2c_read_data: Error (%d) !!!\n", error); + debug("tegra_i2c_read_data: Error (%d) !!!\n", error); return error; } @@ -438,7 +438,7 @@ int i2c_write_data(uchar chip, uchar *buffer, int len) debug("\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra20_i2c_write_data(chip << 1, buffer, len); + rc = tegra_i2c_write_data(chip << 1, buffer, len); if (rc) debug("i2c_write_data(): rc=%d\n", rc); @@ -452,7 +452,7 @@ int i2c_read_data(uchar chip, uchar *buffer, int len) debug("inside i2c_read_data():\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra20_i2c_read_data(chip << 1, buffer, len); + rc = tegra_i2c_read_data(chip << 1, buffer, len); if (rc) { debug("i2c_read_data(): rc=%d\n", rc); return rc; diff --git a/drivers/input/Makefile b/drivers/input/Makefile index 68c6a16bcc2..0805e866787 100644 --- a/drivers/input/Makefile +++ b/drivers/input/Makefile @@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk LIB := $(obj)libinput.o COBJS-$(CONFIG_I8042_KBD) += i8042.o -COBJS-$(CONFIG_TEGRA20_KEYBOARD) += tegra-kbc.o +COBJS-$(CONFIG_TEGRA_KEYBOARD) += tegra-kbc.o ifdef CONFIG_PS2KBD COBJS-y += keyboard.o pc_keyb.o COBJS-$(CONFIG_PS2MULT) += ps2mult.o ps2ser.o diff --git a/drivers/mmc/tegra_mmc.c b/drivers/mmc/tegra_mmc.c index ddfa7279c22..ca8fad86572 100644 --- a/drivers/mmc/tegra_mmc.c +++ b/drivers/mmc/tegra_mmc.c @@ -25,7 +25,7 @@ #include #include #include -#include "tegra_mmc.h" +#include /* support 4 mmc hosts */ struct mmc mmc_dev[4]; @@ -39,31 +39,31 @@ struct mmc_host mmc_host[4]; * @param host Structure to fill in (base, reg, mmc_id) * @param dev_index Device index (0-3) */ -static void tegra20_get_setup(struct mmc_host *host, int dev_index) +static void tegra_get_setup(struct mmc_host *host, int dev_index) { - debug("tegra20_get_base_mmc: dev_index = %d\n", dev_index); + debug("tegra_get_setup: dev_index = %d\n", dev_index); switch (dev_index) { case 1: - host->base = TEGRA20_SDMMC3_BASE; + host->base = TEGRA_SDMMC3_BASE; host->mmc_id = PERIPH_ID_SDMMC3; break; case 2: - host->base = TEGRA20_SDMMC2_BASE; + host->base = TEGRA_SDMMC2_BASE; host->mmc_id = PERIPH_ID_SDMMC2; break; case 3: - host->base = TEGRA20_SDMMC1_BASE; + host->base = TEGRA_SDMMC1_BASE; host->mmc_id = PERIPH_ID_SDMMC1; break; case 0: default: - host->base = TEGRA20_SDMMC4_BASE; + host->base = TEGRA_SDMMC4_BASE; host->mmc_id = PERIPH_ID_SDMMC4; break; } - host->reg = (struct tegra20_mmc *)host->base; + host->reg = (struct tegra_mmc *)host->base; } static void mmc_prepare_data(struct mmc_host *host, struct mmc_data *data) @@ -345,7 +345,7 @@ static void mmc_change_clock(struct mmc_host *host, uint clock) debug(" mmc_change_clock called\n"); /* - * Change Tegra20 SDMMCx clock divisor here. Source is 216MHz, + * Change Tegra SDMMCx clock divisor here. Source is 216MHz, * PLLP_OUT0 */ if (clock == 0) @@ -494,11 +494,11 @@ static int mmc_core_init(struct mmc *mmc) return 0; } -int tegra20_mmc_getcd(struct mmc *mmc) +int tegra_mmc_getcd(struct mmc *mmc) { struct mmc_host *host = (struct mmc_host *)mmc->priv; - debug("tegra20_mmc_getcd called\n"); + debug("tegra_mmc_getcd called\n"); if (host->cd_gpio >= 0) return !gpio_get_value(host->cd_gpio); @@ -506,13 +506,13 @@ int tegra20_mmc_getcd(struct mmc *mmc) return 1; } -int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) +int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) { struct mmc_host *host; char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */ struct mmc *mmc; - debug(" tegra20_mmc_init: index %d, bus width %d " + debug(" tegra_mmc_init: index %d, bus width %d " "pwr_gpio %d cd_gpio %d\n", dev_index, bus_width, pwr_gpio, cd_gpio); @@ -521,7 +521,7 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) host->clock = 0; host->pwr_gpio = pwr_gpio; host->cd_gpio = cd_gpio; - tegra20_get_setup(host, dev_index); + tegra_get_setup(host, dev_index); clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000); @@ -539,12 +539,12 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) mmc = &mmc_dev[dev_index]; - sprintf(mmc->name, "Tegra20 SD/MMC"); + sprintf(mmc->name, "Tegra SD/MMC"); mmc->priv = host; mmc->send_cmd = mmc_send_cmd; mmc->set_ios = mmc_set_ios; mmc->init = mmc_core_init; - mmc->getcd = tegra20_mmc_getcd; + mmc->getcd = tegra_mmc_getcd; mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; if (bus_width == 8) @@ -559,7 +559,7 @@ int tegra20_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio) * max freq is highest HS eMMC clock as per the SD/MMC spec * (actually 52MHz) * Both of these are the closest equivalents w/216MHz source - * clock and Tegra20 SDMMC divisors. + * clock and Tegra SDMMC divisors. */ mmc->f_min = 375000; mmc->f_max = 48000000; diff --git a/drivers/mmc/tegra_mmc.h b/drivers/mmc/tegra_mmc.h deleted file mode 100644 index b1f25641978..00000000000 --- a/drivers/mmc/tegra_mmc.h +++ /dev/null @@ -1,131 +0,0 @@ -/* - * (C) Copyright 2009 SAMSUNG Electronics - * Minkyu Kang - * Portions Copyright (C) 2011-2012 NVIDIA Corporation - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - */ - -#ifndef __TEGRA_MMC_H_ -#define __TEGRA_MMC_H_ - -#define TEGRA20_SDMMC1_BASE 0xC8000000 -#define TEGRA20_SDMMC2_BASE 0xC8000200 -#define TEGRA20_SDMMC3_BASE 0xC8000400 -#define TEGRA20_SDMMC4_BASE 0xC8000600 - -#ifndef __ASSEMBLY__ -struct tegra20_mmc { - unsigned int sysad; /* _SYSTEM_ADDRESS_0 */ - unsigned short blksize; /* _BLOCK_SIZE_BLOCK_COUNT_0 15:00 */ - unsigned short blkcnt; /* _BLOCK_SIZE_BLOCK_COUNT_0 31:16 */ - unsigned int argument; /* _ARGUMENT_0 */ - unsigned short trnmod; /* _CMD_XFER_MODE_0 15:00 xfer mode */ - unsigned short cmdreg; /* _CMD_XFER_MODE_0 31:16 cmd reg */ - unsigned int rspreg0; /* _RESPONSE_R0_R1_0 CMD RESP 31:00 */ - unsigned int rspreg1; /* _RESPONSE_R2_R3_0 CMD RESP 63:32 */ - unsigned int rspreg2; /* _RESPONSE_R4_R5_0 CMD RESP 95:64 */ - unsigned int rspreg3; /* _RESPONSE_R6_R7_0 CMD RESP 127:96 */ - unsigned int bdata; /* _BUFFER_DATA_PORT_0 */ - unsigned int prnsts; /* _PRESENT_STATE_0 */ - unsigned char hostctl; /* _POWER_CONTROL_HOST_0 7:00 */ - unsigned char pwrcon; /* _POWER_CONTROL_HOST_0 15:8 */ - unsigned char blkgap; /* _POWER_CONTROL_HOST_9 23:16 */ - unsigned char wakcon; /* _POWER_CONTROL_HOST_0 31:24 */ - unsigned short clkcon; /* _CLOCK_CONTROL_0 15:00 */ - unsigned char timeoutcon; /* _TIMEOUT_CTRL 23:16 */ - unsigned char swrst; /* _SW_RESET_ 31:24 */ - unsigned int norintsts; /* _INTERRUPT_STATUS_0 */ - unsigned int norintstsen; /* _INTERRUPT_STATUS_ENABLE_0 */ - unsigned int norintsigen; /* _INTERRUPT_SIGNAL_ENABLE_0 */ - unsigned short acmd12errsts; /* _AUTO_CMD12_ERR_STATUS_0 15:00 */ - unsigned char res1[2]; /* _RESERVED 31:16 */ - unsigned int capareg; /* _CAPABILITIES_0 */ - unsigned char res2[4]; /* RESERVED, offset 44h-47h */ - unsigned int maxcurr; /* _MAXIMUM_CURRENT_0 */ - unsigned char res3[4]; /* RESERVED, offset 4Ch-4Fh */ - unsigned short setacmd12err; /* offset 50h */ - unsigned short setinterr; /* offset 52h */ - unsigned char admaerr; /* offset 54h */ - unsigned char res4[3]; /* RESERVED, offset 55h-57h */ - unsigned long admaaddr; /* offset 58h-5Fh */ - unsigned char res5[0x9c]; /* RESERVED, offset 60h-FBh */ - unsigned short slotintstatus; /* offset FCh */ - unsigned short hcver; /* HOST Version */ - unsigned char res6[0x100]; /* RESERVED, offset 100h-1FFh */ -}; - -#define TEGRA_MMC_HOSTCTL_DMASEL_MASK (3 << 3) -#define TEGRA_MMC_HOSTCTL_DMASEL_SDMA (0 << 3) -#define TEGRA_MMC_HOSTCTL_DMASEL_ADMA2_32BIT (2 << 3) -#define TEGRA_MMC_HOSTCTL_DMASEL_ADMA2_64BIT (3 << 3) - -#define TEGRA_MMC_TRNMOD_DMA_ENABLE (1 << 0) -#define TEGRA_MMC_TRNMOD_BLOCK_COUNT_ENABLE (1 << 1) -#define TEGRA_MMC_TRNMOD_DATA_XFER_DIR_SEL_WRITE (0 << 4) -#define TEGRA_MMC_TRNMOD_DATA_XFER_DIR_SEL_READ (1 << 4) -#define TEGRA_MMC_TRNMOD_MULTI_BLOCK_SELECT (1 << 5) - -#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_MASK (3 << 0) -#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_NO_RESPONSE (0 << 0) -#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_136 (1 << 0) -#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48 (2 << 0) -#define TEGRA_MMC_CMDREG_RESP_TYPE_SELECT_LENGTH_48_BUSY (3 << 0) - -#define TEGRA_MMC_TRNMOD_CMD_CRC_CHECK (1 << 3) -#define TEGRA_MMC_TRNMOD_CMD_INDEX_CHECK (1 << 4) -#define TEGRA_MMC_TRNMOD_DATA_PRESENT_SELECT_DATA_TRANSFER (1 << 5) - -#define TEGRA_MMC_PRNSTS_CMD_INHIBIT_CMD (1 << 0) -#define TEGRA_MMC_PRNSTS_CMD_INHIBIT_DAT (1 << 1) - -#define TEGRA_MMC_CLKCON_INTERNAL_CLOCK_ENABLE (1 << 0) -#define TEGRA_MMC_CLKCON_INTERNAL_CLOCK_STABLE (1 << 1) -#define TEGRA_MMC_CLKCON_SD_CLOCK_ENABLE (1 << 2) - -#define TEGRA_MMC_CLKCON_SDCLK_FREQ_SEL_SHIFT 8 -#define TEGRA_MMC_CLKCON_SDCLK_FREQ_SEL_MASK (0xff << 8) - -#define TEGRA_MMC_SWRST_SW_RESET_FOR_ALL (1 << 0) -#define TEGRA_MMC_SWRST_SW_RESET_FOR_CMD_LINE (1 << 1) -#define TEGRA_MMC_SWRST_SW_RESET_FOR_DAT_LINE (1 << 2) - -#define TEGRA_MMC_NORINTSTS_CMD_COMPLETE (1 << 0) -#define TEGRA_MMC_NORINTSTS_XFER_COMPLETE (1 << 1) -#define TEGRA_MMC_NORINTSTS_DMA_INTERRUPT (1 << 3) -#define TEGRA_MMC_NORINTSTS_ERR_INTERRUPT (1 << 15) -#define TEGRA_MMC_NORINTSTS_CMD_TIMEOUT (1 << 16) - -#define TEGRA_MMC_NORINTSTSEN_CMD_COMPLETE (1 << 0) -#define TEGRA_MMC_NORINTSTSEN_XFER_COMPLETE (1 << 1) -#define TEGRA_MMC_NORINTSTSEN_DMA_INTERRUPT (1 << 3) -#define TEGRA_MMC_NORINTSTSEN_BUFFER_WRITE_READY (1 << 4) -#define TEGRA_MMC_NORINTSTSEN_BUFFER_READ_READY (1 << 5) - -#define TEGRA_MMC_NORINTSIGEN_XFER_COMPLETE (1 << 1) - -struct mmc_host { - struct tegra20_mmc *reg; - unsigned int version; /* SDHCI spec. version */ - unsigned int clock; /* Current clock (MHz) */ - unsigned int base; /* Base address, SDMMC1/2/3/4 */ - enum periph_id mmc_id; /* Peripheral ID: PERIPH_ID_... */ - int pwr_gpio; /* Power GPIO */ - int cd_gpio; /* Change Detect GPIO */ -}; - -#endif /* __ASSEMBLY__ */ -#endif /* __TEGRA_MMC_H_ */ diff --git a/drivers/spi/tegra_spi.c b/drivers/spi/tegra_spi.c index 2355e022b02..18b00b2cae9 100644 --- a/drivers/spi/tegra_spi.c +++ b/drivers/spi/tegra_spi.c @@ -72,9 +72,9 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, return NULL; } - if (max_hz > TEGRA20_SPI_MAX_FREQ) { + if (max_hz > TEGRA_SPI_MAX_FREQ) { printf("SPI error: unsupported frequency %d Hz. Max frequency" - " is %d Hz\n", max_hz, TEGRA20_SPI_MAX_FREQ); + " is %d Hz\n", max_hz, TEGRA_SPI_MAX_FREQ); return NULL; } @@ -86,7 +86,7 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, spi->slave.bus = bus; spi->slave.cs = cs; spi->freq = max_hz; - spi->regs = (struct spi_tegra *)TEGRA20_SPI_BASE; + spi->regs = (struct spi_tegra *)NV_PA_SPI_BASE; spi->mode = mode; return &spi->slave; diff --git a/include/configs/harmony.h b/include/configs/harmony.h index 69857dd5810..e407ff4ca53 100644 --- a/include/configs/harmony.h +++ b/include/configs/harmony.h @@ -34,15 +34,15 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Harmony) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Harmony" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Harmony" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: keyboard satellite board UART, default */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE -#ifdef CONFIG_TEGRA20_ENABLE_UARTA +#ifdef CONFIG_TEGRA_ENABLE_UARTA /* UARTA: debug board UART */ #define CONFIG_SYS_NS16550_COM2 NV_PA_APB_UARTA_BASE #endif @@ -66,7 +66,7 @@ #define CONFIG_CMD_NAND #define CONFIG_TEGRA_NAND #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE /* Environment in NAND (which is 512M), aligned to start of last sector */ #define CONFIG_ENV_IS_IN_NAND @@ -87,6 +87,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/medcom.h b/include/configs/medcom.h index bce03a49fab..678b36b6cff 100644 --- a/include/configs/medcom.h +++ b/include/configs/medcom.h @@ -35,11 +35,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Medcom) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Medcom" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Medcom" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F @@ -78,6 +78,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/paz00.h b/include/configs/paz00.h index 99b8753c586..24cda4839ee 100644 --- a/include/configs/paz00.h +++ b/include/configs/paz00.h @@ -27,11 +27,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Paz00) MOD # " -#define CONFIG_TEGRA20_BOARD_STRING "Compal Paz00" +#define CONFIG_TEGRA_BOARD_STRING "Compal Paz00" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA +#define CONFIG_TEGRA_ENABLE_UARTA #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_PAZ00 @@ -69,6 +69,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/plutux.h b/include/configs/plutux.h index 42291d4e28b..65b42edc270 100644 --- a/include/configs/plutux.h +++ b/include/configs/plutux.h @@ -35,11 +35,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Plutux) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Plutux" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Plutux" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F @@ -78,6 +78,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index 69965021edf..de19e38deb4 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -27,7 +27,7 @@ #include /* LP0 suspend / resume */ -#define CONFIG_TEGRA20_LP0 +#define CONFIG_TEGRA_LP0 #define CONFIG_AES #define CONFIG_TEGRA_PMU #define CONFIG_TPS6586X_POWER @@ -42,11 +42,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (SeaBoard) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Seaboard" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Seaboard" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE /* On Seaboard: GPIO_PI3 = Port I = 8, bit = 3 */ @@ -96,15 +96,15 @@ #define CONFIG_CMD_DHCP /* Enable keyboard */ -#define CONFIG_TEGRA20_KEYBOARD +#define CONFIG_TEGRA_KEYBOARD #define CONFIG_KEYBOARD -#undef TEGRA20_DEVICE_SETTINGS -#define TEGRA20_DEVICE_SETTINGS "stdin=serial,tegra-kbc\0" \ - "stdout=serial\0" \ - "stderr=serial\0" +#undef TEGRA_DEVICE_SETTINGS +#define TEGRA_DEVICE_SETTINGS "stdin=serial,tegra-kbc\0" \ + "stdout=serial\0" \ + "stderr=serial\0" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" /* NAND support */ #define CONFIG_CMD_NAND @@ -114,5 +114,5 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Somewhat oddly, the NAND base address must be a config option */ -#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE #endif /* __CONFIG_H */ diff --git a/include/configs/tec.h b/include/configs/tec.h index 9d14d15f693..d5da3c7a88c 100644 --- a/include/configs/tec.h +++ b/include/configs/tec.h @@ -35,12 +35,12 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (TEC) # " -#define CONFIG_TEGRA20_BOARD_STRING "Avionic Design Tamonten Evaluation Carrier" +#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten Evaluation Carrier" #define CONFIG_SYS_BOARD_ODMDATA 0x2b0d8011 /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD /* UARTD: debug UART */ +#define CONFIG_TEGRA_ENABLE_UARTD /* UARTD: debug UART */ #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_BOARD_EARLY_INIT_F @@ -55,7 +55,7 @@ #define CONFIG_CMD_NAND #define CONFIG_TEGRA_NAND #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE TEGRA20_NAND_BASE +#define CONFIG_SYS_NAND_BASE NV_PA_NAND_BASE /* Environment in NAND, aligned to start of last sector */ #define CONFIG_ENV_IS_IN_NAND @@ -87,6 +87,6 @@ "ext2load mmc 0 0x17000000 /boot/uImage;" \ "bootm" -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h new file mode 100644 index 00000000000..168b64be52f --- /dev/null +++ b/include/configs/tegra-common-post.h @@ -0,0 +1,214 @@ +/* + * (C) Copyright 2010-2012 + * NVIDIA Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __TEGRA_COMMON_POST_H +#define __TEGRA_COMMON_POST_H + +#ifdef CONFIG_BOOTCOMMAND + +#define BOOTCMDS_COMMON "" + +#else + +#ifdef CONFIG_CMD_EXT2 +#define BOOT_FSTYPE_EXT2 "ext2 " +#else +#define BOOT_FSTYPE_EXT2 "" +#endif + +#ifdef CONFIG_CMD_FAT +#define BOOT_FSTYPE_FAT "fat" +#else +#define BOOT_FSTYPE_FAT "" +#endif + +#ifdef CONFIG_CMD_MMC +#define BOOTCMDS_MMC \ + "mmc_boot=" \ + "setenv devtype mmc; " \ + "if mmc dev ${devnum}; then " \ + "run scan_boot; " \ + "fi\0" \ + "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0" \ + "bootcmd_mmc1=setenv devnum 1; run mmc_boot;\0" +#define BOOT_TARGETS_MMC "mmc1 mmc0" +#else +#define BOOTCMDS_MMC "" +#define BOOT_TARGETS_MMC "" +#endif + +#ifdef CONFIG_CMD_USB +#define BOOTCMD_INIT_USB "run usb_init; " +#define BOOTCMDS_USB \ + "usb_init=" \ + "if ${usb_need_init}; then " \ + "set usb_need_init false; " \ + "usb start 0; " \ + "fi\0" \ + \ + "usb_boot=" \ + "setenv devtype usb; " \ + BOOTCMD_INIT_USB \ + "if usb dev ${devnum}; then " \ + "run scan_boot; " \ + "fi\0" \ + \ + "bootcmd_usb0=setenv devnum 0; run usb_boot;\0" +#define BOOT_TARGETS_USB "usb0" +#else +#define BOOTCMD_INIT_USB "" +#define BOOTCMDS_USB "" +#define BOOT_TARGETS_USB "" +#endif + +#ifdef CONFIG_CMD_DHCP +#define BOOTCMDS_DHCP \ + "bootcmd_dhcp=" \ + BOOTCMD_INIT_USB \ + "if dhcp ${scriptaddr} boot.scr.uimg; then "\ + "source ${scriptaddr}; " \ + "fi\0" +#define BOOT_TARGETS_DHCP "dhcp" +#else +#define BOOTCMDS_DHCP "" +#define BOOT_TARGETS_DHCP "" +#endif + +#define BOOTCMDS_COMMON \ + "scriptaddr=0x400000\0" \ + \ + "rootpart=1\0" \ + \ + "script_boot=" \ + "if ${fs}load ${devtype} ${devnum}:${rootpart} " \ + "${scriptaddr} ${prefix}${script}; then " \ + "echo ${script} found! Executing ...;" \ + "source ${scriptaddr};" \ + "fi;\0" \ + \ + "scan_boot=" \ + "echo Scanning ${devtype} ${devnum}...; " \ + "for fs in ${boot_fstypes}; do " \ + "for prefix in ${boot_prefixes}; do " \ + "for script in ${boot_scripts}; do " \ + "run script_boot; " \ + "done; " \ + "done; " \ + "done;\0" \ + \ + "boot_targets=" \ + BOOT_TARGETS_MMC " " \ + BOOT_TARGETS_USB " " \ + BOOT_TARGETS_DHCP " " \ + "\0" \ + \ + "boot_fstypes=" \ + BOOT_FSTYPE_EXT2 " " \ + BOOT_FSTYPE_FAT " " \ + "\0" \ + \ + "boot_prefixes=/ /boot/\0" \ + \ + "boot_scripts=boot.scr.uimg boot.scr\0" \ + \ + BOOTCMDS_MMC \ + BOOTCMDS_USB \ + BOOTCMDS_DHCP + +#define CONFIG_BOOTCOMMAND \ + "for target in ${boot_targets}; do run bootcmd_${target}; done" + +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + TEGRA_DEVICE_SETTINGS \ + "fdt_load=0x01000000\0" \ + "fdt_high=01100000\0" \ + BOOTCMDS_COMMON + +/* overrides for SPL build here */ +#ifdef CONFIG_SPL_BUILD + +/* remove devicetree support */ +#ifdef CONFIG_OF_CONTROL +#undef CONFIG_OF_CONTROL +#endif + +/* remove SERIAL_MULTI */ +#ifdef CONFIG_SERIAL_MULTI +#undef CONFIG_SERIAL_MULTI +#endif + +/* remove I2C support */ +#ifdef CONFIG_TEGRA_I2C +#undef CONFIG_TEGRA_I2C +#endif +#ifdef CONFIG_CMD_I2C +#undef CONFIG_CMD_I2C +#endif + +/* remove MMC support */ +#ifdef CONFIG_MMC +#undef CONFIG_MMC +#endif +#ifdef CONFIG_GENERIC_MMC +#undef CONFIG_GENERIC_MMC +#endif +#ifdef CONFIG_TEGRA_MMC +#undef CONFIG_TEGRA_MMC +#endif +#ifdef CONFIG_CMD_MMC +#undef CONFIG_CMD_MMC +#endif + +/* remove partitions/filesystems */ +#ifdef CONFIG_DOS_PARTITION +#undef CONFIG_DOS_PARTITION +#endif +#ifdef CONFIG_EFI_PARTITION +#undef CONFIG_EFI_PARTITION +#endif +#ifdef CONFIG_CMD_EXT2 +#undef CONFIG_CMD_EXT2 +#endif +#ifdef CONFIG_CMD_FAT +#undef CONFIG_CMD_FAT +#endif + +/* remove USB */ +#ifdef CONFIG_USB_EHCI +#undef CONFIG_USB_EHCI +#endif +#ifdef CONFIG_USB_EHCI_TEGRA +#undef CONFIG_USB_EHCI_TEGRA +#endif +#ifdef CONFIG_USB_STORAGE +#undef CONFIG_USB_STORAGE +#endif +#ifdef CONFIG_CMD_USB +#undef CONFIG_CMD_USB +#endif + +#endif /* CONFIG_SPL_BUILD */ + +#endif /* __TEGRA_COMMON_POST_H */ diff --git a/include/configs/tegra20-common-post.h b/include/configs/tegra20-common-post.h deleted file mode 100644 index 42f270f7bcd..00000000000 --- a/include/configs/tegra20-common-post.h +++ /dev/null @@ -1,214 +0,0 @@ -/* - * (C) Copyright 2010-2012 - * NVIDIA Corporation - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __TEGRA20_COMMON_POST_H -#define __TEGRA20_COMMON_POST_H - -#ifdef CONFIG_BOOTCOMMAND - -#define BOOTCMDS_COMMON "" - -#else - -#ifdef CONFIG_CMD_EXT2 -#define BOOT_FSTYPE_EXT2 "ext2 " -#else -#define BOOT_FSTYPE_EXT2 "" -#endif - -#ifdef CONFIG_CMD_FAT -#define BOOT_FSTYPE_FAT "fat" -#else -#define BOOT_FSTYPE_FAT "" -#endif - -#ifdef CONFIG_CMD_MMC -#define BOOTCMDS_MMC \ - "mmc_boot=" \ - "setenv devtype mmc; " \ - "if mmc dev ${devnum}; then " \ - "run scan_boot; " \ - "fi\0" \ - "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0" \ - "bootcmd_mmc1=setenv devnum 1; run mmc_boot;\0" -#define BOOT_TARGETS_MMC "mmc1 mmc0" -#else -#define BOOTCMDS_MMC "" -#define BOOT_TARGETS_MMC "" -#endif - -#ifdef CONFIG_CMD_USB -#define BOOTCMD_INIT_USB "run usb_init; " -#define BOOTCMDS_USB \ - "usb_init=" \ - "if ${usb_need_init}; then " \ - "set usb_need_init false; " \ - "usb start 0; " \ - "fi\0" \ - \ - "usb_boot=" \ - "setenv devtype usb; " \ - BOOTCMD_INIT_USB \ - "if usb dev ${devnum}; then " \ - "run scan_boot; " \ - "fi\0" \ - \ - "bootcmd_usb0=setenv devnum 0; run usb_boot;\0" -#define BOOT_TARGETS_USB "usb0" -#else -#define BOOTCMD_INIT_USB "" -#define BOOTCMDS_USB "" -#define BOOT_TARGETS_USB "" -#endif - -#ifdef CONFIG_CMD_DHCP -#define BOOTCMDS_DHCP \ - "bootcmd_dhcp=" \ - BOOTCMD_INIT_USB \ - "if dhcp ${scriptaddr} boot.scr.uimg; then "\ - "source ${scriptaddr}; " \ - "fi\0" -#define BOOT_TARGETS_DHCP "dhcp" -#else -#define BOOTCMDS_DHCP "" -#define BOOT_TARGETS_DHCP "" -#endif - -#define BOOTCMDS_COMMON \ - "scriptaddr=0x400000\0" \ - \ - "rootpart=1\0" \ - \ - "script_boot=" \ - "if ${fs}load ${devtype} ${devnum}:${rootpart} " \ - "${scriptaddr} ${prefix}${script}; then " \ - "echo ${script} found! Executing ...;" \ - "source ${scriptaddr};" \ - "fi;\0" \ - \ - "scan_boot=" \ - "echo Scanning ${devtype} ${devnum}...; " \ - "for fs in ${boot_fstypes}; do " \ - "for prefix in ${boot_prefixes}; do " \ - "for script in ${boot_scripts}; do " \ - "run script_boot; " \ - "done; " \ - "done; " \ - "done;\0" \ - \ - "boot_targets=" \ - BOOT_TARGETS_MMC " " \ - BOOT_TARGETS_USB " " \ - BOOT_TARGETS_DHCP " " \ - "\0" \ - \ - "boot_fstypes=" \ - BOOT_FSTYPE_EXT2 " " \ - BOOT_FSTYPE_FAT " " \ - "\0" \ - \ - "boot_prefixes=/ /boot/\0" \ - \ - "boot_scripts=boot.scr.uimg boot.scr\0" \ - \ - BOOTCMDS_MMC \ - BOOTCMDS_USB \ - BOOTCMDS_DHCP - -#define CONFIG_BOOTCOMMAND \ - "for target in ${boot_targets}; do run bootcmd_${target}; done" - -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - TEGRA20_DEVICE_SETTINGS \ - "fdt_load=0x01000000\0" \ - "fdt_high=01100000\0" \ - BOOTCMDS_COMMON - -/* overrides for SPL build here */ -#ifdef CONFIG_SPL_BUILD - -/* remove devicetree support */ -#ifdef CONFIG_OF_CONTROL -#undef CONFIG_OF_CONTROL -#endif - -/* remove SERIAL_MULTI */ -#ifdef CONFIG_SERIAL_MULTI -#undef CONFIG_SERIAL_MULTI -#endif - -/* remove I2C support */ -#ifdef CONFIG_TEGRA_I2C -#undef CONFIG_TEGRA_I2C -#endif -#ifdef CONFIG_CMD_I2C -#undef CONFIG_CMD_I2C -#endif - -/* remove MMC support */ -#ifdef CONFIG_MMC -#undef CONFIG_MMC -#endif -#ifdef CONFIG_GENERIC_MMC -#undef CONFIG_GENERIC_MMC -#endif -#ifdef CONFIG_TEGRA20_MMC -#undef CONFIG_TEGRA20_MMC -#endif -#ifdef CONFIG_CMD_MMC -#undef CONFIG_CMD_MMC -#endif - -/* remove partitions/filesystems */ -#ifdef CONFIG_DOS_PARTITION -#undef CONFIG_DOS_PARTITION -#endif -#ifdef CONFIG_EFI_PARTITION -#undef CONFIG_EFI_PARTITION -#endif -#ifdef CONFIG_CMD_EXT2 -#undef CONFIG_CMD_EXT2 -#endif -#ifdef CONFIG_CMD_FAT -#undef CONFIG_CMD_FAT -#endif - -/* remove USB */ -#ifdef CONFIG_USB_EHCI -#undef CONFIG_USB_EHCI -#endif -#ifdef CONFIG_USB_EHCI_TEGRA -#undef CONFIG_USB_EHCI_TEGRA -#endif -#ifdef CONFIG_USB_STORAGE -#undef CONFIG_USB_STORAGE -#endif -#ifdef CONFIG_CMD_USB -#undef CONFIG_CMD_USB -#endif - -#endif /* CONFIG_SPL_BUILD */ - -#endif /* __TEGRA20_COMMON_POST_H */ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 02cf0cdc14c..098cdb4460d 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -54,7 +54,7 @@ #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_OF_LIBFDT /* enable passing of devicetree */ -#ifdef CONFIG_TEGRA20_LP0 +#ifdef CONFIG_TEGRA_LP0 #define TEGRA_LP0_ADDR 0x1C406000 #define TEGRA_LP0_SIZE 0x2000 #define TEGRA_LP0_VEC \ @@ -132,9 +132,9 @@ /* Environment information, boards can override if required */ #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define TEGRA20_DEVICE_SETTINGS "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" +#define TEGRA_DEVICE_SETTINGS "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" #define CONFIG_LOADADDR 0x408000 /* def. location for kernel */ #define CONFIG_BOOTDELAY 2 /* -1 to disable auto boot */ @@ -157,7 +157,7 @@ /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) -#define CONFIG_SYS_MEMTEST_START (TEGRA20_SDRC_CS0 + 0x600000) +#define CONFIG_SYS_MEMTEST_START (NV_PA_SDRC_CS0 + 0x600000) #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x100000) #define CONFIG_SYS_LOAD_ADDR (0xA00800) /* default */ @@ -169,7 +169,7 @@ * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 TEGRA20_SDRC_CS0 +#define PHYS_SDRAM_1 NV_PA_SDRC_CS0 #define PHYS_SDRAM_1_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_TEXT_BASE 0x0010c000 diff --git a/include/configs/trimslice.h b/include/configs/trimslice.h index b3c524981f5..a46890c0947 100644 --- a/include/configs/trimslice.h +++ b/include/configs/trimslice.h @@ -34,12 +34,12 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (TrimSlice) # " -#define CONFIG_TEGRA20_BOARD_STRING "Compulab Trimslice" +#define CONFIG_TEGRA_BOARD_STRING "Compulab Trimslice" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA -#define CONFIG_TEGRA20_UARTA_GPU +#define CONFIG_TEGRA_ENABLE_UARTA +#define CONFIG_TEGRA_UARTA_GPU #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_TRIMSLICE @@ -94,6 +94,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/ventana.h b/include/configs/ventana.h index f5e1bf81ff1..7d3a54f7432 100644 --- a/include/configs/ventana.h +++ b/include/configs/ventana.h @@ -34,11 +34,11 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Ventana) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Ventana" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Ventana" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTD +#define CONFIG_TEGRA_ENABLE_UARTD #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE #define CONFIG_MACH_TYPE MACH_TYPE_VENTANA @@ -76,6 +76,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/whistler.h b/include/configs/whistler.h index 32357181556..6c565bae14d 100644 --- a/include/configs/whistler.h +++ b/include/configs/whistler.h @@ -34,12 +34,12 @@ /* High-level configuration options */ #define V_PROMPT "Tegra20 (Whistler) # " -#define CONFIG_TEGRA20_BOARD_STRING "NVIDIA Whistler" +#define CONFIG_TEGRA_BOARD_STRING "NVIDIA Whistler" /* Board-specific serial config */ #define CONFIG_SERIAL_MULTI -#define CONFIG_TEGRA20_ENABLE_UARTA -#define CONFIG_TEGRA20_UARTA_UAA_UAB +#define CONFIG_TEGRA_ENABLE_UARTA +#define CONFIG_TEGRA_UARTA_UAA_UAB #define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTA_BASE #define CONFIG_MACH_TYPE MACH_TYPE_WHISTLER @@ -90,6 +90,6 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP -#include "tegra20-common-post.h" +#include "tegra-common-post.h" #endif /* __CONFIG_H */ -- cgit v1.3.1 From f994dc5ecfbb702cc8041de246e7aa58c6ed0e9f Mon Sep 17 00:00:00 2001 From: Otavio Salvador Date: Sat, 15 Sep 2012 08:26:17 +0000 Subject: mx28evk: extend default environment The environment has been based on mx53loco and m28evk but keeping the possibility to easy change the default console device as Freescale and mainline kernels differ on the device name. Signed-off-by: Otavio Salvador --- include/configs/mx28evk.h | 82 ++++++++++++++++++++++++++++++++++++++++++----- 1 file changed, 74 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index 43b40021d6a..dffb744c3dc 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -239,7 +239,6 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" -#define CONFIG_BOOTCOMMAND "run bootcmd_net" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR #define CONFIG_OF_LIBFDT @@ -248,13 +247,80 @@ * Extra Environments */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "console_fsl=console=ttyAM0" \ - "console_mainline=console=ttyAMA0" \ - "netargs=setenv bootargs console=${console_mainline}" \ + "update_nand_full_filename=u-boot.nand\0" \ + "update_nand_firmware_filename=u-boot.sb\0" \ + "update_sd_firmware_filename=u-boot.sd\0" \ + "update_nand_firmware_maxsz=0x100000\0" \ + "update_nand_stride=0x40\0" /* MX28 datasheet ch. 12.12 */ \ + "update_nand_count=0x4\0" /* MX28 datasheet ch. 12.12 */ \ + "update_nand_get_fcb_size=" /* Get size of FCB blocks */ \ + "nand device 0 ; " \ + "nand info ; " \ + "setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \ + "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \ + "update_nand_full=" /* Update FCB, DBBT and FW */ \ + "if tftp ${update_nand_full_filename} ; then " \ + "run update_nand_get_fcb_size ; " \ + "nand scrub -y 0x0 ${filesize} ; " \ + "nand write.raw ${loadaddr} 0x0 ${update_nand_fcb} ; " \ + "setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \ + "setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \ + "nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \ + "fi\0" \ + "update_nand_firmware=" /* Update only firmware */ \ + "if tftp ${update_nand_firmware_filename} ; then " \ + "run update_nand_get_fcb_size ; " \ + "setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \ + "setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \ + "setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \ + "nand erase ${fcb_sz} ${fw_sz} ; " \ + "nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \ + "nand write ${loadaddr} ${fw_off} ${filesize} ; " \ + "fi\0" \ + "update_sd_firmware=" /* Update the SD firmware partition */ \ + "if mmc rescan ; then " \ + "if tftp ${update_sd_firmware_filename} ; then " \ + "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \ + "setexpr fw_sz ${fw_sz} + 1 ; " \ + "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \ + "fi ; " \ + "fi\0" \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console_fsl=ttyAM0\0" \ + "console_mainline=ttyAMA0\0" \ + "mmcdev=0\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rw\0" \ + "mmcrootfstype=ext3 rootwait\0" \ + "mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootm\0" \ + "netargs=setenv bootargs console=${console_mainline},${baudrate} " \ "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot}\0" \ - "bootcmd_net=echo Booting from net ...; " \ - "run netargs; " \ - "dhcp ${uimage}; bootm\0" \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "dhcp ${uimage}; bootm\0" + +#define CONFIG_BOOTCOMMAND \ + "if mmc rescan ${mmcdev}; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" #endif /* __MX28EVK_CONFIG_H__ */ -- cgit v1.3.1