From 9553df86d3a319c3a1a7cde7e4edd6eeb5aa64c7 Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Tue, 16 Oct 2007 15:26:51 -0500 Subject: Initial mpc8610hpcd cpu/, README and include/ files. Signed-off-by: Ed Swarthout Signed-off-by: Mahesh Jade Signed-off-by: Jason Jin Signed-off-by: Jon Loeliger --- include/asm-ppc/processor.h | 1 + include/configs/MPC8610HPCD.h | 660 ++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 661 insertions(+) create mode 100644 include/configs/MPC8610HPCD.h (limited to 'include') diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 0a160e2513a..07c1de05b33 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -875,6 +875,7 @@ #define SVR_8544_E 0x803C #define SVR_8548 0x8031 #define SVR_8548_E 0x8039 +#define SVR_8610 0x80A0 #define SVR_8641 0x8090 #define SVR_8568_E 0x807D diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h new file mode 100644 index 00000000000..be3434a4c9b --- /dev/null +++ b/include/configs/MPC8610HPCD.h @@ -0,0 +1,660 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 as published by the Free Software Foundation. + */ + +/* + * MPC8610HPCD board configuration file + * + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_MPC86xx 1 /* MPC86xx */ +#define CONFIG_MPC8610 1 /* MPC8610 specific */ +#define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */ +#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ +#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ + +#ifdef RUN_DIAG +#define CFG_DIAG_ADDR 0xff800000 +#endif + +#define CFG_RESET_ADDRESS 0xfff00100 + +#define CONFIG_PCI 1 /* Enable PCI/PCIE*/ +#define CONFIG_PCI1 1 /* PCI controler 1 */ +#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */ +#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ + +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_SPD_EEPROM /* Use SPD for DDR */ +#undef CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + +#define CONFIG_ALTIVEC 1 + +/* + * L2CR setup -- make sure this is right for your board! + */ +#define CFG_L2 +#define L2_INIT 0 +#define L2_ENABLE (L2CR_L2E) + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) +#endif + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest region */ +#define CFG_MEMTEST_END 0x00400000 +#define CFG_ALT_MEMTEST + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) +#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000) + +#define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000) + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define MPC86xx_DDR_SDRAM_CLK_CNTL + +#if defined(CONFIG_SPD_EEPROM) +/* + * Determine DDR configuration from I2C interface. + */ +#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */ +#else +/* + * Manually set up DDR1 parameters + */ + +#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ + +#if 0 /* TODO */ +#define CFG_DDR_CS0_BNDS 0x0000000F +#define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ +#define CFG_DDR_EXT_REFRESH 0x00000000 +#define CFG_DDR_TIMING_0 0x00260802 +#define CFG_DDR_TIMING_1 0x3935d322 +#define CFG_DDR_TIMING_2 0x14904cc8 +#define CFG_DDR_MODE_1 0x00480432 +#define CFG_DDR_MODE_2 0x00000000 +#define CFG_DDR_INTERVAL 0x06180100 +#define CFG_DDR_DATA_INIT 0xdeadbeef +#define CFG_DDR_CLK_CTRL 0x03800000 +#define CFG_DDR_OCD_CTRL 0x00000000 +#define CFG_DDR_OCD_STATUS 0x00000000 +#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ +#define CFG_DDR_CONTROL2 0x04400010 + +#define CFG_DDR_ERR_INT_EN 0x00000000 +#define CFG_DDR_ERR_DIS 0x00000000 +#define CFG_DDR_SBE 0x000f0000 + /* Not used in fixed_sdram function */ +#define CFG_DDR_MODE 0x00000022 +#define CFG_DDR_CS1_BNDS 0x00000000 +#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */ +#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */ +#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */ +#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ +#endif +#endif + +#define CFG_ID_EEPROM +#define ID_EEPROM_ADDR 0x57 + + +#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ +#define CFG_FLASH_BASE2 0xf8000000 + +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2} + +#define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */ +#define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ + +#define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */ +#define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ +#if 0 /* TODO */ +#define CFG_BR2_PRELIM 0xf0000000 +#define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ +#endif +#define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */ +#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ + + +#define PIXIS_BASE 0xe8000000 /* PIXIS registers */ +#define PIXIS_ID 0x0 /* Board ID at offset 0 */ +#define PIXIS_VER 0x1 /* Board version at offset 1 */ +#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ +#define PIXIS_RST 0x4 /* PIXIS Reset Control register */ +#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */ +#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ +#define PIXIS_VCTL 0x10 /* VELA Control Register */ +#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ +#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ +#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ +#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ +#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ +#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ +#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ + +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#if defined(CFG_RAMBOOT) +#undef CONFIG_SPD_EEPROM +#define CFG_SDRAM_SIZE 256 +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#ifndef CFG_INIT_RAM_LOCK +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#else +#define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ +#endif +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* + * Pass open firmware flat tree to kernel + */ +#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,8610@0" +#define OF_SOC "soc@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc@e0000000/serial@4500" + +#define CFG_64BIT_VSPRINTF 1 +#define CFG_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe1000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +/* For RTL8139 */ +#define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); }) +#define _IO_BASE 0x00000000 + +/* controller 1, Base address 0xa000 */ +#define CFG_PCIE1_MEM_BASE 0xa0000000 +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCIE1_IO_BASE 0x00000000 +#define CFG_PCIE1_IO_PHYS 0xe3000000 +#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ + +/* controller 2, Base Address 0x9000 */ +#define CFG_PCIE2_MEM_BASE 0x90000000 +#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE +#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */ +#define CFG_PCIE2_IO_PHYS 0xe2000000 +#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */ + + +#if defined(CONFIG_PCI) + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#if 0 /* TODO */ +/* enable onboard uli network support */ +#endif + +#define CONFIG_RTL8139 +#define CONFIG_SK98 +#define CONFIG_EEPRO100 +#define CONFIG_TULIP + +#if 0 /* TODO */ +/************************************************************ + * USB support + ************************************************************/ +#define CONFIG_USB_OHCI 1 +#define CONFIG_USB_KEYBOARD 1 +#define CFG_DEVICE_DEREGISTER +#define CFG_USB_INTERRUPT_POLL 1 +#endif + +#if !defined(CONFIG_PCI_PNP) +#define PCI_ENET0_IOADDR 0xe0000000 +#define PCI_ENET0_MEMADDR 0xe0000000 +#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#define CONFIG_DOS_PARTITION +#define CONFIG_SCSI_AHCI + +#ifdef CONFIG_SCSI_AHCI +#define CONFIG_SATA_ULI5288 +#define CFG_SCSI_MAX_SCSI_ID 4 +#define CFG_SCSI_MAX_LUN 1 +#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) +#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#endif + +#endif /* CONFIG_PCI */ + +/* + * BAT0 2G Cacheable, non-guarded + * 0x0000_0000 2G DDR + */ +#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) +#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) +#define CFG_IBAT0U CFG_DBAT0U + +/* + * BAT1 1G Cache-inhibited, guarded + * 0x8000_0000 256M PCI-1 Memory + * 0xa000_0000 256M PCI-Express 1 Memory + * 0x9000_0000 256M PCI-Express 2 Memory + */ + +#define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP) +#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT1U CFG_DBAT1U + +/* + * BAT2 32M Cache-inhibited, guarded + * 0xe100_0000 1M PCI-1 I/O + * 0xe200_0000 1M PCI-Express 2 I/O + * + */ + +#define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT2U CFG_DBAT2U + +/* + * BAT3 1M Cache-inhibited, guarded + * 0xe300_0000 1M PCI-Express 1 I/O + * + */ + +#define CFG_DBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT3U (CFG_PCIE1_IO_PHYS | BATU_BL_1M | BATU_VS | BATU_VP) +#define CFG_IBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT3U CFG_DBAT3U + +/* + * BAT4 4M Cache-inhibited, guarded + * 0xe000_0000 4M CCSR + */ +#define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) +#define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT4U CFG_DBAT4U + +/* + * BAT5 128K Cacheable, non-guarded + * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory) + */ +#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_IBAT5L CFG_DBAT5L +#define CFG_IBAT5U CFG_DBAT5U + +/* + * BAT6 256M Cache-inhibited, guarded + * 0xf000_0000 256M FLASH + */ +#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CFG_IBAT6U CFG_DBAT6U + +/* + * BAT7 4M Cache-inhibited, guarded + * 0xe800_0000 4M PIXIS + */ +#define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) +#define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT7U CFG_DBAT7U + + +/* + * Environment + */ +#ifndef CFG_RAMBOOT +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#define CFG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */ +#define CFG_ENV_SIZE 0x2000 +#else +#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + +#if defined(CFG_RAMBOOT) +#undef CONFIG_CMD_ENV +#endif + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#define CONFIG_CMD_SCSI +#define CONFIG_CMD_EXT2 +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_IPADDR 192.168.1.100 + +#define CONFIG_HOSTNAME unknown +#define CONFIG_ROOTPATH /opt/nfsroot +#define CONFIG_BOOTFILE uImage +#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#if defined(CONFIG_PCI1) +#define PCI_ENV \ + "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ + "echo e;md ${a}e00 9\0" \ + "pci1regs=setenv a e0008; run pcireg\0" \ + "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ + "pci d.w $b.0 56 1\0" \ + "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \ + "pci w.w $b.0 56 ffff\0" \ + "pci1err=setenv a e0008; run pcierr\0" \ + "pci1errc=setenv a e0008; run pcierrc\0" +#else +#define PCI_ENV "" +#endif + +#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) +#define PCIE_ENV \ + "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ + "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ + "pcie1regs=setenv a e000a; run pciereg\0" \ + "pcie2regs=setenv a e0009; run pciereg\0" \ + "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\ + "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \ + "pci d $b.0 130 1\0" \ + "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\ + "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \ + "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \ + "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ + "pcie1err=setenv a e000a; run pcieerr\0" \ + "pcie2err=setenv a e0009; run pcieerr\0" \ + "pcie1errc=setenv a e000a; run pcieerrc\0" \ + "pcie2errc=setenv a e0009; run pcieerrc\0" +#else +#define PCIE_ENV "" +#endif + +#define DMA_ENV \ + "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\ + "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \ + "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\ + "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \ + "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\ + "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \ + "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\ + "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0" + + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ + "dtbaddr=c00000\0" \ + "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \ + "bdev=sda3\0" \ + "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ + "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ + "maxcpus=1" \ + "eoi=mw e00400b0 0\0" \ + "iack=md e00400a0 1\0" \ + "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \ + "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \ + "md ${a}f00 5\0" \ + "ddr1regs=setenv a e0002; run ddrreg\0" \ + "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \ + "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \ + "md ${a}e60 1; md ${a}ef0 1d\0" \ + "guregs=setenv a e00e0; run gureg\0" \ + "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \ + "mcmregs=setenv a e0001; run mcmreg\0" \ + "diuregs=md e002c000 1d\0" \ + "dium=mw e002c01c\0" \ + "diuerr=md e002c014 1\0" \ + "othbootargs=debug\0" \ + "pmregs=md e00e1000 2b\0" \ + "lawregs=md e0000c08 4b\0" \ + "lbcregs=md e0005000 36\0" \ + "dma0regs=md e0021100 12\0" \ + "dma1regs=md e0021180 12\0" \ + "dma2regs=md e0021200 12\0" \ + "dma3regs=md e0021280 12\0" \ + PCI_ENV \ + PCIE_ENV \ + DMA_ENV + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $dtbaddr $dtbfile;" \ + "bootm $loadaddr - $dtbaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $dtbaddr $dtbfile;" \ + "bootm $loadaddr $ramdiskaddr $dtbaddr" + +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs root=/dev/$bdev rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $dtbaddr $dtbfile;" \ + "bootm $loadaddr - $dtbaddr" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From c7c6da23028f146d912514b95aefa3da7cf37699 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 3 Oct 2007 07:34:10 +0200 Subject: ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (1) This patch is the first patch of a series to make the 440SPe PCIe code usable on different 4xx PPC platforms. In preperation for the new 405EX which is also equipped with PCIe interfaces. (1) This patch renames the files from 440spe_pcie to 4xx_pcie Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 9 +- board/amcc/yucca/yucca.c | 6 +- cpu/ppc4xx/440spe_pcie.c | 1067 -------------------------------------------- cpu/ppc4xx/440spe_pcie.h | 174 -------- cpu/ppc4xx/4xx_pcie.c | 1067 ++++++++++++++++++++++++++++++++++++++++++++ cpu/ppc4xx/Makefile | 5 +- include/asm-ppc/4xx_pcie.h | 174 ++++++++ 7 files changed, 1250 insertions(+), 1252 deletions(-) delete mode 100644 cpu/ppc4xx/440spe_pcie.c delete mode 100644 cpu/ppc4xx/440spe_pcie.h create mode 100644 cpu/ppc4xx/4xx_pcie.c create mode 100644 include/asm-ppc/4xx_pcie.h (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index a49066fcc94..0c8e6cb701e 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -24,12 +24,11 @@ #include #include -#include #include -#include -#include - -#include "../cpu/ppc4xx/440spe_pcie.h" +#include +#include +#include +#include #undef PCIE_ENDPOINT /* #define PCIE_ENDPOINT 1 */ diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index d7cc384ba0b..17c3ba0f17d 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -27,12 +27,12 @@ #include #include -#include #include -#include +#include +#include +#include #include "yucca.h" -#include "../cpu/ppc4xx/440spe_pcie.h" DECLARE_GLOBAL_DATA_PTR; diff --git a/cpu/ppc4xx/440spe_pcie.c b/cpu/ppc4xx/440spe_pcie.c deleted file mode 100644 index 3eac0ae62cd..00000000000 --- a/cpu/ppc4xx/440spe_pcie.c +++ /dev/null @@ -1,1067 +0,0 @@ -/* - * (C) Copyright 2006 - 2007 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Copyright (c) 2005 Cisco Systems. All rights reserved. - * Roland Dreier - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - */ - -#include -#include -#include -#include -#include - -#if defined(CONFIG_440SPE) && defined(CONFIG_PCI) - -#include "440spe_pcie.h" - -enum { - PTYPE_ENDPOINT = 0x0, - PTYPE_LEGACY_ENDPOINT = 0x1, - PTYPE_ROOT_PORT = 0x4, - - LNKW_X1 = 0x1, - LNKW_X4 = 0x4, - LNKW_X8 = 0x8 -}; - -static u8* pcie_get_base(struct pci_controller *hose, unsigned int devfn) -{ - u8 *base = (u8*)hose->cfg_data; - - /* use local configuration space for the first bus */ - if (PCI_BUS(devfn) == 0) { - if (hose->cfg_data == (u8*)CFG_PCIE0_CFGBASE) - base = (u8*)CFG_PCIE0_XCFGBASE; - if (hose->cfg_data == (u8*)CFG_PCIE1_CFGBASE) - base = (u8*)CFG_PCIE1_XCFGBASE; - if (hose->cfg_data == (u8*)CFG_PCIE2_CFGBASE) - base = (u8*)CFG_PCIE2_XCFGBASE; - } - - return base; -} - -static void pcie_dmer_disable(void) -{ - mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) | GPL_DMER_MASK_DISA); - mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) | GPL_DMER_MASK_DISA); - mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) | GPL_DMER_MASK_DISA); -} - -static void pcie_dmer_enable(void) -{ - mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE0_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) & ~GPL_DMER_MASK_DISA); - mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE1_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) & ~GPL_DMER_MASK_DISA); - mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE2_BASE), - mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) & ~GPL_DMER_MASK_DISA); -} - -static int pcie_read_config(struct pci_controller *hose, unsigned int devfn, - int offset, int len, u32 *val) { - - u8 *address; - *val = 0; - - /* - * Bus numbers are relative to hose->first_busno - */ - devfn -= PCI_BDF(hose->first_busno, 0, 0); - - /* - * NOTICE: configuration space ranges are currenlty mapped only for - * the first 16 buses, so such limit must be imposed. In case more - * buses are required the TLB settings in board/amcc//init.S - * need to be altered accordingly (one bus takes 1 MB of memory space). - */ - if (PCI_BUS(devfn) >= 16) - return 0; - - /* - * Only single device/single function is supported for the primary and - * secondary buses of the 440SPe host bridge. - */ - if ((!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 0))) && - ((PCI_BUS(devfn) == 0) || (PCI_BUS(devfn) == 1))) - return 0; - - address = pcie_get_base(hose, devfn); - offset += devfn << 4; - - /* - * Reading from configuration space of non-existing device can - * generate transaction errors. For the read duration we suppress - * assertion of machine check exceptions to avoid those. - */ - pcie_dmer_disable (); - - switch (len) { - case 1: - *val = in_8(hose->cfg_data + offset); - break; - case 2: - *val = in_le16((u16 *)(hose->cfg_data + offset)); - break; - default: - *val = in_le32((u32*)(hose->cfg_data + offset)); - break; - } - - pcie_dmer_enable (); - - return 0; -} - -static int pcie_write_config(struct pci_controller *hose, unsigned int devfn, - int offset, int len, u32 val) { - - u8 *address; - - /* - * Bus numbers are relative to hose->first_busno - */ - devfn -= PCI_BDF(hose->first_busno, 0, 0); - - /* - * Same constraints as in pcie_read_config(). - */ - if (PCI_BUS(devfn) >= 16) - return 0; - - if ((!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 0))) && - ((PCI_BUS(devfn) == 0) || (PCI_BUS(devfn) == 1))) - return 0; - - address = pcie_get_base(hose, devfn); - offset += devfn << 4; - - /* - * Suppress MCK exceptions, similar to pcie_read_config() - */ - pcie_dmer_disable (); - - switch (len) { - case 1: - out_8(hose->cfg_data + offset, val); - break; - case 2: - out_le16((u16 *)(hose->cfg_data + offset), val); - break; - default: - out_le32((u32 *)(hose->cfg_data + offset), val); - break; - } - - pcie_dmer_enable (); - - return 0; -} - -int pcie_read_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 *val) -{ - u32 v; - int rv; - - rv = pcie_read_config(hose, dev, offset, 1, &v); - *val = (u8)v; - return rv; -} - -int pcie_read_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 *val) -{ - u32 v; - int rv; - - rv = pcie_read_config(hose, dev, offset, 2, &v); - *val = (u16)v; - return rv; -} - -int pcie_read_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 *val) -{ - u32 v; - int rv; - - rv = pcie_read_config(hose, dev, offset, 3, &v); - *val = (u32)v; - return rv; -} - -int pcie_write_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 val) -{ - return pcie_write_config(hose,(u32)dev,offset,1,val); -} - -int pcie_write_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 val) -{ - return pcie_write_config(hose,(u32)dev,offset,2,(u32 )val); -} - -int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 val) -{ - return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val); -} - -static void ppc440spe_setup_utl(u32 port) { - - volatile void *utl_base = NULL; - - /* - * Map UTL registers - */ - switch (port) { - case 0: - mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x0000000c); - mtdcr(DCRN_PEGPL_REGBAL(PCIE0), 0x20000000); - mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001); - mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0x68782800); - break; - - case 1: - mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x0000000c); - mtdcr(DCRN_PEGPL_REGBAL(PCIE1), 0x20001000); - mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001); - mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0x68782800); - break; - - case 2: - mtdcr(DCRN_PEGPL_REGBAH(PCIE2), 0x0000000c); - mtdcr(DCRN_PEGPL_REGBAL(PCIE2), 0x20002000); - mtdcr(DCRN_PEGPL_REGMSK(PCIE2), 0x00007001); - mtdcr(DCRN_PEGPL_SPECIAL(PCIE2), 0x68782800); - break; - } - utl_base = (unsigned int *)(CFG_PCIE_BASE + 0x1000 * port); - - /* - * Set buffer allocations and then assert VRB and TXE. - */ - out_be32(utl_base + PEUTL_OUTTR, 0x08000000); - out_be32(utl_base + PEUTL_INTR, 0x02000000); - out_be32(utl_base + PEUTL_OPDBSZ, 0x10000000); - out_be32(utl_base + PEUTL_PBBSZ, 0x53000000); - out_be32(utl_base + PEUTL_IPHBSZ, 0x08000000); - out_be32(utl_base + PEUTL_IPDBSZ, 0x10000000); - out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000); - out_be32(utl_base + PEUTL_PCTL, 0x80800066); -} - -static int check_error(void) -{ - u32 valPE0, valPE1, valPE2; - int err = 0; - - /* SDR0_PEGPLLLCT1 reset */ - if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) { - printf("PCIE: SDR0_PEGPLLLCT1 reset error 0x%x\n", valPE0); - } - - valPE0 = SDR_READ(PESDR0_RCSSET); - valPE1 = SDR_READ(PESDR1_RCSSET); - valPE2 = SDR_READ(PESDR2_RCSSET); - - /* SDR0_PExRCSSET rstgu */ - if (!(valPE0 & 0x01000000) || - !(valPE1 & 0x01000000) || - !(valPE2 & 0x01000000)) { - printf("PCIE: SDR0_PExRCSSET rstgu error\n"); - err = -1; - } - - /* SDR0_PExRCSSET rstdl */ - if (!(valPE0 & 0x00010000) || - !(valPE1 & 0x00010000) || - !(valPE2 & 0x00010000)) { - printf("PCIE: SDR0_PExRCSSET rstdl error\n"); - err = -1; - } - - /* SDR0_PExRCSSET rstpyn */ - if ((valPE0 & 0x00001000) || - (valPE1 & 0x00001000) || - (valPE2 & 0x00001000)) { - printf("PCIE: SDR0_PExRCSSET rstpyn error\n"); - err = -1; - } - - /* SDR0_PExRCSSET hldplb */ - if ((valPE0 & 0x10000000) || - (valPE1 & 0x10000000) || - (valPE2 & 0x10000000)) { - printf("PCIE: SDR0_PExRCSSET hldplb error\n"); - err = -1; - } - - /* SDR0_PExRCSSET rdy */ - if ((valPE0 & 0x00100000) || - (valPE1 & 0x00100000) || - (valPE2 & 0x00100000)) { - printf("PCIE: SDR0_PExRCSSET rdy error\n"); - err = -1; - } - - /* SDR0_PExRCSSET shutdown */ - if ((valPE0 & 0x00000100) || - (valPE1 & 0x00000100) || - (valPE2 & 0x00000100)) { - printf("PCIE: SDR0_PExRCSSET shutdown error\n"); - err = -1; - } - return err; -} - -/* - * Initialize PCI Express core - */ -int ppc440spe_init_pcie(void) -{ - int time_out = 20; - - /* Set PLL clock receiver to LVPECL */ - SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) | 1 << 28); - - if (check_error()) - return -1; - - if (!(SDR_READ(PESDR0_PLLLCT2) & 0x10000)) - { - printf("PCIE: PESDR_PLLCT2 resistance calibration failed (0x%08x)\n", - SDR_READ(PESDR0_PLLLCT2)); - return -1; - } - /* De-assert reset of PCIe PLL, wait for lock */ - SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) & ~(1 << 24)); - udelay(3); - - while (time_out) { - if (!(SDR_READ(PESDR0_PLLLCT3) & 0x10000000)) { - time_out--; - udelay(1); - } else - break; - } - if (!time_out) { - printf("PCIE: VCO output not locked\n"); - return -1; - } - return 0; -} - -/* - * Yucca board as End point and root point setup - * and - * testing inbound and out bound windows - * - * YUCCA board can be plugged into another yucca board or you can get PCI-E - * cable which can be used to setup loop back from one port to another port. - * Please rememeber that unless there is a endpoint plugged in to root port it - * will not initialize. It is the same in case of endpoint , unless there is - * root port attached it will not initialize. - * - * In this release of software all the PCI-E ports are configured as either - * endpoint or rootpoint.In future we will have support for selective ports - * setup as endpoint and root point in single board. - * - * Once your board came up as root point , you can verify by reading - * /proc/bus/pci/devices. Where you can see the configuration registers - * of end point device attached to the port. - * - * Enpoint cofiguration can be verified by connecting Yucca board to any - * host or another yucca board. Then try to scan the device. In case of - * linux use "lspci" or appripriate os command. - * - * How do I verify the inbound and out bound windows ?(yucca to yucca) - * in this configuration inbound and outbound windows are setup to access - * sram memroy area. SRAM is at 0x4 0000 0000 , on PLB bus. This address - * is mapped at 0x90000000. From u-boot prompt write data 0xb000 0000, - * This is waere your POM(PLB out bound memory window) mapped. then - * read the data from other yucca board's u-boot prompt at address - * 0x9000 0000(SRAM). Data should match. - * In case of inbound , write data to u-boot command prompt at 0xb000 0000 - * which is mapped to 0x4 0000 0000. Now on rootpoint yucca u-boot prompt check - * data at 0x9000 0000(SRAM).Data should match. - */ -int ppc440spe_init_pcie_rootport(int port) -{ - static int core_init; - volatile u32 val = 0; - int attempts; - - if (!core_init) { - ++core_init; - if (ppc440spe_init_pcie()) - return -1; - } - - /* - * Initialize various parts of the PCI Express core for our port: - * - * - Set as a root port and enable max width - * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). - * - Set up UTL configuration. - * - Increase SERDES drive strength to levels suggested by AMCC. - * - De-assert RSTPYN, RSTDL and RSTGU. - * - * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with - * default setting 0x11310000. The register has new fields, - * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core - * hang. - */ - switch (port) { - case 0: - SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12); - - SDR_WRITE(PESDR0_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR0_UTLSET2, 0x11000000); - SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); - SDR_WRITE(PESDR0_RCSSET, - (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 1: - SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR1_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR1_UTLSET2, 0x11000000); - SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR1_RCSSET, - (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 2: - SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR2_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR2_UTLSET2, 0x11000000); - SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR2_RCSSET, - (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - } - /* - * Notice: the following delay has critical impact on device - * initialization - if too short (<50ms) the link doesn't get up. - */ - mdelay(100); - - switch (port) { - case 0: - val = SDR_READ(PESDR0_RCSSTS); - break; - case 1: - val = SDR_READ(PESDR1_RCSSTS); - break; - case 2: - val = SDR_READ(PESDR2_RCSSTS); - break; - } - - if (val & (1 << 20)) { - printf("PCIE%d: PGRST failed %08x\n", port, val); - return -1; - } - - /* - * Verify link is up - */ - val = 0; - switch (port) { - case 0: - val = SDR_READ(PESDR0_LOOP); - break; - case 1: - val = SDR_READ(PESDR1_LOOP); - break; - case 2: - val = SDR_READ(PESDR2_LOOP); - break; - } - if (!(val & 0x00001000)) { - printf("PCIE%d: link is not up.\n", port); - return -1; - } - - /* - * Setup UTL registers - but only on revA! - * We use default settings for revB chip. - */ - if (!ppc440spe_revB()) - ppc440spe_setup_utl(port); - - /* - * We map PCI Express configuration access into the 512MB regions - * - * NOTICE: revB is very strict about PLB real addressess and ranges to - * be mapped for config space; it seems to only work with d_nnnn_nnnn - * range (hangs the core upon config transaction attempts when set - * otherwise) while revA uses c_nnnn_nnnn. - * - * For revA: - * PCIE0: 0xc_4000_0000 - * PCIE1: 0xc_8000_0000 - * PCIE2: 0xc_c000_0000 - * - * For revB: - * PCIE0: 0xd_0000_0000 - * PCIE1: 0xd_2000_0000 - * PCIE2: 0xd_4000_0000 - */ - - switch (port) { - case 0: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); - } else { - /* revA */ - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ - break; - - case 1: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ - break; - - case 2: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ - break; - } - - /* - * Check for VC0 active and assert RDY. - */ - attempts = 10; - switch (port) { - case 0: - while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE0: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); - break; - case 1: - while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE1: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); - break; - case 2: - while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE2: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); - break; - } - mdelay(100); - - return 0; -} - -int ppc440spe_init_pcie_endport(int port) -{ - static int core_init; - volatile u32 val = 0; - int attempts; - - if (!core_init) { - ++core_init; - if (ppc440spe_init_pcie()) - return -1; - } - - /* - * Initialize various parts of the PCI Express core for our port: - * - * - Set as a end port and enable max width - * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). - * - Set up UTL configuration. - * - Increase SERDES drive strength to levels suggested by AMCC. - * - De-assert RSTPYN, RSTDL and RSTGU. - * - * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with - * default setting 0x11310000. The register has new fields, - * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core - * hang. - */ - switch (port) { - case 0: - SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X8 << 12); - - SDR_WRITE(PESDR0_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR0_UTLSET2, 0x11000000); - SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); - SDR_WRITE(PESDR0_RCSSET, - (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 1: - SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR1_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR1_UTLSET2, 0x11000000); - SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR1_RCSSET, - (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 2: - SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR2_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR2_UTLSET2, 0x11000000); - SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR2_RCSSET, - (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - } - /* - * Notice: the following delay has critical impact on device - * initialization - if too short (<50ms) the link doesn't get up. - */ - mdelay(100); - - switch (port) { - case 0: val = SDR_READ(PESDR0_RCSSTS); break; - case 1: val = SDR_READ(PESDR1_RCSSTS); break; - case 2: val = SDR_READ(PESDR2_RCSSTS); break; - } - - if (val & (1 << 20)) { - printf("PCIE%d: PGRST failed %08x\n", port, val); - return -1; - } - - /* - * Verify link is up - */ - val = 0; - switch (port) - { - case 0: - val = SDR_READ(PESDR0_LOOP); - break; - case 1: - val = SDR_READ(PESDR1_LOOP); - break; - case 2: - val = SDR_READ(PESDR2_LOOP); - break; - } - if (!(val & 0x00001000)) { - printf("PCIE%d: link is not up.\n", port); - return -1; - } - - /* - * Setup UTL registers - but only on revA! - * We use default settings for revB chip. - */ - if (!ppc440spe_revB()) - ppc440spe_setup_utl(port); - - /* - * We map PCI Express configuration access into the 512MB regions - * - * NOTICE: revB is very strict about PLB real addressess and ranges to - * be mapped for config space; it seems to only work with d_nnnn_nnnn - * range (hangs the core upon config transaction attempts when set - * otherwise) while revA uses c_nnnn_nnnn. - * - * For revA: - * PCIE0: 0xc_4000_0000 - * PCIE1: 0xc_8000_0000 - * PCIE2: 0xc_c000_0000 - * - * For revB: - * PCIE0: 0xd_0000_0000 - * PCIE1: 0xd_2000_0000 - * PCIE2: 0xd_4000_0000 - */ - switch (port) { - case 0: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); - } else { - /* revA */ - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ - break; - - case 1: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ - break; - - case 2: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ - break; - } - - /* - * Check for VC0 active and assert RDY. - */ - attempts = 10; - switch (port) { - case 0: - while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE0: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); - break; - case 1: - while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE1: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); - break; - case 2: - while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE2: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); - break; - } - mdelay(100); - - return 0; -} - -void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port) -{ - volatile void *mbase = NULL; - volatile void *rmbase = NULL; - - pci_set_ops(hose, - pcie_read_config_byte, - pcie_read_config_word, - pcie_read_config_dword, - pcie_write_config_byte, - pcie_write_config_word, - pcie_write_config_dword); - - switch (port) { - case 0: - mbase = (u32 *)CFG_PCIE0_XCFGBASE; - rmbase = (u32 *)CFG_PCIE0_CFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE; - break; - case 1: - mbase = (u32 *)CFG_PCIE1_XCFGBASE; - rmbase = (u32 *)CFG_PCIE1_CFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; - break; - case 2: - mbase = (u32 *)CFG_PCIE2_XCFGBASE; - rmbase = (u32 *)CFG_PCIE2_CFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; - break; - } - - /* - * Set bus numbers on our root port - */ - out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0); - out_8((u8 *)mbase + PCI_SECONDARY_BUS, 1); - out_8((u8 *)mbase + PCI_SUBORDINATE_BUS, 1); - - /* - * Set up outbound translation to hose->mem_space from PLB - * addresses at an offset of 0xd_0000_0000. We set the low - * bits of the mask to 11 to turn off splitting into 8 - * subregions and to enable the outbound translation. - */ - out_le32(mbase + PECFG_POM0LAH, 0x00000000); - out_le32(mbase + PECFG_POM0LAL, 0x00000000); - - switch (port) { - case 0: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - case 1: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - case 2: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - } - - /* Set up 16GB inbound memory window at 0 */ - out_le32(mbase + PCI_BASE_ADDRESS_0, 0); - out_le32(mbase + PCI_BASE_ADDRESS_1, 0); - out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); - out_le32(mbase + PECFG_BAR0LMPA, 0); - - out_le32(mbase + PECFG_PIM01SAH, 0xffff0000); - out_le32(mbase + PECFG_PIM01SAL, 0x00000000); - out_le32(mbase + PECFG_PIM0LAL, 0); - out_le32(mbase + PECFG_PIM0LAH, 0); - out_le32(mbase + PECFG_PIM1LAL, 0x00000000); - out_le32(mbase + PECFG_PIM1LAH, 0x00000004); - out_le32(mbase + PECFG_PIMEN, 0x1); - - /* Enable I/O, Mem, and Busmaster cycles */ - out_le16((u16 *)(mbase + PCI_COMMAND), - in_le16((u16 *)(mbase + PCI_COMMAND)) | - PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); - printf("PCIE:%d successfully set as rootpoint\n",port); - - /* Set Device and Vendor Id */ - switch (port) { - case 0: - out_le16(mbase + 0x200, 0xaaa0); - out_le16(mbase + 0x202, 0xbed0); - break; - case 1: - out_le16(mbase + 0x200, 0xaaa1); - out_le16(mbase + 0x202, 0xbed1); - break; - case 2: - out_le16(mbase + 0x200, 0xaaa2); - out_le16(mbase + 0x202, 0xbed2); - break; - default: - out_le16(mbase + 0x200, 0xaaa3); - out_le16(mbase + 0x202, 0xbed3); - } - - /* Set Class Code to PCI-PCI bridge and Revision Id to 1 */ - out_le32(mbase + 0x208, 0x06040001); - -} - -int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port) -{ - volatile void *mbase = NULL; - int attempts = 0; - - pci_set_ops(hose, - pcie_read_config_byte, - pcie_read_config_word, - pcie_read_config_dword, - pcie_write_config_byte, - pcie_write_config_word, - pcie_write_config_dword); - - switch (port) { - case 0: - mbase = (u32 *)CFG_PCIE0_XCFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE; - break; - case 1: - mbase = (u32 *)CFG_PCIE1_XCFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; - break; - case 2: - mbase = (u32 *)CFG_PCIE2_XCFGBASE; - hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; - break; - } - - /* - * Set up outbound translation to hose->mem_space from PLB - * addresses at an offset of 0xd_0000_0000. We set the low - * bits of the mask to 11 to turn off splitting into 8 - * subregions and to enable the outbound translation. - */ - out_le32(mbase + PECFG_POM0LAH, 0x00001ff8); - out_le32(mbase + PECFG_POM0LAL, 0x00001000); - - switch (port) { - case 0: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - case 1: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - case 2: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); - mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); - mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), - ~(CFG_PCIE_MEMSIZE - 1) | 3); - break; - } - - /* Set up 16GB inbound memory window at 0 */ - out_le32(mbase + PCI_BASE_ADDRESS_0, 0); - out_le32(mbase + PCI_BASE_ADDRESS_1, 0); - out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); - out_le32(mbase + PECFG_BAR0LMPA, 0); - out_le32(mbase + PECFG_PIM0LAL, 0x00000000); - out_le32(mbase + PECFG_PIM0LAH, 0x00000004); /* pointing to SRAM */ - out_le32(mbase + PECFG_PIMEN, 0x1); - - /* Enable I/O, Mem, and Busmaster cycles */ - out_le16((u16 *)(mbase + PCI_COMMAND), - in_le16((u16 *)(mbase + PCI_COMMAND)) | - PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); - out_le16(mbase + 0x200,0xcaad); /* Setting vendor ID */ - out_le16(mbase + 0x202,0xfeed); /* Setting device ID */ - attempts = 10; - switch (port) { - case 0: - while (!(SDR_READ(PESDR0_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE0: BMEN is not active\n"); - return -1; - } - mdelay(1000); - } - break; - case 1: - while (!(SDR_READ(PESDR1_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE1: BMEN is not active\n"); - return -1; - } - mdelay(1000); - } - break; - case 2: - while (!(SDR_READ(PESDR2_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE2: BMEN is not active\n"); - return -1; - } - mdelay(1000); - } - break; - } - printf("PCIE:%d successfully set as endpoint\n",port); - - return 0; -} -#endif /* CONFIG_440SPE && CONFIG_PCI */ diff --git a/cpu/ppc4xx/440spe_pcie.h b/cpu/ppc4xx/440spe_pcie.h deleted file mode 100644 index 38745eb797c..00000000000 --- a/cpu/ppc4xx/440spe_pcie.h +++ /dev/null @@ -1,174 +0,0 @@ -/* - * Copyright (c) 2005 Cisco Systems. All rights reserved. - * Roland Dreier - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#include -#ifndef __440SPE_PCIE_H -#define __440SPE_PCIE_H - -#define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);}) - -#define DCRN_SDR0_CFGADDR 0x00e -#define DCRN_SDR0_CFGDATA 0x00f - -#define DCRN_PCIE0_BASE 0x100 -#define DCRN_PCIE1_BASE 0x120 -#define DCRN_PCIE2_BASE 0x140 -#define PCIE0 DCRN_PCIE0_BASE -#define PCIE1 DCRN_PCIE1_BASE -#define PCIE2 DCRN_PCIE2_BASE - -#define DCRN_PEGPL_CFGBAH(base) (base + 0x00) -#define DCRN_PEGPL_CFGBAL(base) (base + 0x01) -#define DCRN_PEGPL_CFGMSK(base) (base + 0x02) -#define DCRN_PEGPL_MSGBAH(base) (base + 0x03) -#define DCRN_PEGPL_MSGBAL(base) (base + 0x04) -#define DCRN_PEGPL_MSGMSK(base) (base + 0x05) -#define DCRN_PEGPL_OMR1BAH(base) (base + 0x06) -#define DCRN_PEGPL_OMR1BAL(base) (base + 0x07) -#define DCRN_PEGPL_OMR1MSKH(base) (base + 0x08) -#define DCRN_PEGPL_OMR1MSKL(base) (base + 0x09) -#define DCRN_PEGPL_REGBAH(base) (base + 0x12) -#define DCRN_PEGPL_REGBAL(base) (base + 0x13) -#define DCRN_PEGPL_REGMSK(base) (base + 0x14) -#define DCRN_PEGPL_SPECIAL(base) (base + 0x15) -#define DCRN_PEGPL_CFG(base) (base + 0x16) - -/* - * System DCRs (SDRs) - */ -#define PESDR0_PLLLCT1 0x03a0 -#define PESDR0_PLLLCT2 0x03a1 -#define PESDR0_PLLLCT3 0x03a2 - -#define PESDR0_UTLSET1 0x0300 -#define PESDR0_UTLSET2 0x0301 -#define PESDR0_DLPSET 0x0302 -#define PESDR0_LOOP 0x0303 -#define PESDR0_RCSSET 0x0304 -#define PESDR0_RCSSTS 0x0305 -#define PESDR0_HSSL0SET1 0x0306 -#define PESDR0_HSSL0SET2 0x0307 -#define PESDR0_HSSL0STS 0x0308 -#define PESDR0_HSSL1SET1 0x0309 -#define PESDR0_HSSL1SET2 0x030a -#define PESDR0_HSSL1STS 0x030b -#define PESDR0_HSSL2SET1 0x030c -#define PESDR0_HSSL2SET2 0x030d -#define PESDR0_HSSL2STS 0x030e -#define PESDR0_HSSL3SET1 0x030f -#define PESDR0_HSSL3SET2 0x0310 -#define PESDR0_HSSL3STS 0x0311 -#define PESDR0_HSSL4SET1 0x0312 -#define PESDR0_HSSL4SET2 0x0313 -#define PESDR0_HSSL4STS 0x0314 -#define PESDR0_HSSL5SET1 0x0315 -#define PESDR0_HSSL5SET2 0x0316 -#define PESDR0_HSSL5STS 0x0317 -#define PESDR0_HSSL6SET1 0x0318 -#define PESDR0_HSSL6SET2 0x0319 -#define PESDR0_HSSL6STS 0x031a -#define PESDR0_HSSL7SET1 0x031b -#define PESDR0_HSSL7SET2 0x031c -#define PESDR0_HSSL7STS 0x031d -#define PESDR0_HSSCTLSET 0x031e -#define PESDR0_LANE_ABCD 0x031f -#define PESDR0_LANE_EFGH 0x0320 - -#define PESDR1_UTLSET1 0x0340 -#define PESDR1_UTLSET2 0x0341 -#define PESDR1_DLPSET 0x0342 -#define PESDR1_LOOP 0x0343 -#define PESDR1_RCSSET 0x0344 -#define PESDR1_RCSSTS 0x0345 -#define PESDR1_HSSL0SET1 0x0346 -#define PESDR1_HSSL0SET2 0x0347 -#define PESDR1_HSSL0STS 0x0348 -#define PESDR1_HSSL1SET1 0x0349 -#define PESDR1_HSSL1SET2 0x034a -#define PESDR1_HSSL1STS 0x034b -#define PESDR1_HSSL2SET1 0x034c -#define PESDR1_HSSL2SET2 0x034d -#define PESDR1_HSSL2STS 0x034e -#define PESDR1_HSSL3SET1 0x034f -#define PESDR1_HSSL3SET2 0x0350 -#define PESDR1_HSSL3STS 0x0351 -#define PESDR1_HSSCTLSET 0x0352 -#define PESDR1_LANE_ABCD 0x0353 - -#define PESDR2_UTLSET1 0x0370 -#define PESDR2_UTLSET2 0x0371 -#define PESDR2_DLPSET 0x0372 -#define PESDR2_LOOP 0x0373 -#define PESDR2_RCSSET 0x0374 -#define PESDR2_RCSSTS 0x0375 -#define PESDR2_HSSL0SET1 0x0376 -#define PESDR2_HSSL0SET2 0x0377 -#define PESDR2_HSSL0STS 0x0378 -#define PESDR2_HSSL1SET1 0x0379 -#define PESDR2_HSSL1SET2 0x037a -#define PESDR2_HSSL1STS 0x037b -#define PESDR2_HSSL2SET1 0x037c -#define PESDR2_HSSL2SET2 0x037d -#define PESDR2_HSSL2STS 0x037e -#define PESDR2_HSSL3SET1 0x037f -#define PESDR2_HSSL3SET2 0x0380 -#define PESDR2_HSSL3STS 0x0381 -#define PESDR2_HSSCTLSET 0x0382 -#define PESDR2_LANE_ABCD 0x0383 - -/* - * UTL register offsets - */ -#define PEUTL_PBBSZ 0x20 -#define PEUTL_OPDBSZ 0x68 -#define PEUTL_IPHBSZ 0x70 -#define PEUTL_IPDBSZ 0x78 -#define PEUTL_OUTTR 0x90 -#define PEUTL_INTR 0x98 -#define PEUTL_PCTL 0xa0 -#define PEUTL_RCIRQEN 0xb8 - -/* - * Config space register offsets - */ -#define PECFG_BAR0LMPA 0x210 -#define PECFG_BAR0HMPA 0x214 -#define PECFG_BAR1MPA 0x218 -#define PECFG_BAR2MPA 0x220 - -#define PECFG_PIMEN 0x33c -#define PECFG_PIM0LAL 0x340 -#define PECFG_PIM0LAH 0x344 -#define PECFG_PIM1LAL 0x348 -#define PECFG_PIM1LAH 0x34c -#define PECFG_PIM01SAL 0x350 -#define PECFG_PIM01SAH 0x354 - -#define PECFG_POM0LAL 0x380 -#define PECFG_POM0LAH 0x384 - -#define SDR_READ(offset) ({\ - mtdcr(DCRN_SDR0_CFGADDR, offset); \ - mfdcr(DCRN_SDR0_CFGDATA);}) - -#define SDR_WRITE(offset, data) ({\ - mtdcr(DCRN_SDR0_CFGADDR, offset); \ - mtdcr(DCRN_SDR0_CFGDATA,data);}) - -#define GPL_DMER_MASK_DISA 0x02000000 - -int ppc440spe_init_pcie(void); -int ppc440spe_init_pcie_rootport(int port); -void yucca_setup_pcie_fpga_rootpoint(int port); -void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port); -int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port); -int yucca_pcie_card_present(int port); -int pcie_hose_scan(struct pci_controller *hose, int bus); -#endif /* __440SPE_PCIE_H */ diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c new file mode 100644 index 00000000000..8906adc51e2 --- /dev/null +++ b/cpu/ppc4xx/4xx_pcie.c @@ -0,0 +1,1067 @@ +/* + * (C) Copyright 2006 - 2007 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * Roland Dreier + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include + +#if defined(CONFIG_440SPE) && defined(CONFIG_PCI) + +#include + +enum { + PTYPE_ENDPOINT = 0x0, + PTYPE_LEGACY_ENDPOINT = 0x1, + PTYPE_ROOT_PORT = 0x4, + + LNKW_X1 = 0x1, + LNKW_X4 = 0x4, + LNKW_X8 = 0x8 +}; + +static u8* pcie_get_base(struct pci_controller *hose, unsigned int devfn) +{ + u8 *base = (u8*)hose->cfg_data; + + /* use local configuration space for the first bus */ + if (PCI_BUS(devfn) == 0) { + if (hose->cfg_data == (u8*)CFG_PCIE0_CFGBASE) + base = (u8*)CFG_PCIE0_XCFGBASE; + if (hose->cfg_data == (u8*)CFG_PCIE1_CFGBASE) + base = (u8*)CFG_PCIE1_XCFGBASE; + if (hose->cfg_data == (u8*)CFG_PCIE2_CFGBASE) + base = (u8*)CFG_PCIE2_XCFGBASE; + } + + return base; +} + +static void pcie_dmer_disable(void) +{ + mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) | GPL_DMER_MASK_DISA); + mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) | GPL_DMER_MASK_DISA); + mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) | GPL_DMER_MASK_DISA); +} + +static void pcie_dmer_enable(void) +{ + mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE0_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) & ~GPL_DMER_MASK_DISA); + mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE1_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) & ~GPL_DMER_MASK_DISA); + mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE2_BASE), + mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) & ~GPL_DMER_MASK_DISA); +} + +static int pcie_read_config(struct pci_controller *hose, unsigned int devfn, + int offset, int len, u32 *val) { + + u8 *address; + *val = 0; + + /* + * Bus numbers are relative to hose->first_busno + */ + devfn -= PCI_BDF(hose->first_busno, 0, 0); + + /* + * NOTICE: configuration space ranges are currenlty mapped only for + * the first 16 buses, so such limit must be imposed. In case more + * buses are required the TLB settings in board/amcc//init.S + * need to be altered accordingly (one bus takes 1 MB of memory space). + */ + if (PCI_BUS(devfn) >= 16) + return 0; + + /* + * Only single device/single function is supported for the primary and + * secondary buses of the 440SPe host bridge. + */ + if ((!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 0))) && + ((PCI_BUS(devfn) == 0) || (PCI_BUS(devfn) == 1))) + return 0; + + address = pcie_get_base(hose, devfn); + offset += devfn << 4; + + /* + * Reading from configuration space of non-existing device can + * generate transaction errors. For the read duration we suppress + * assertion of machine check exceptions to avoid those. + */ + pcie_dmer_disable (); + + switch (len) { + case 1: + *val = in_8(hose->cfg_data + offset); + break; + case 2: + *val = in_le16((u16 *)(hose->cfg_data + offset)); + break; + default: + *val = in_le32((u32*)(hose->cfg_data + offset)); + break; + } + + pcie_dmer_enable (); + + return 0; +} + +static int pcie_write_config(struct pci_controller *hose, unsigned int devfn, + int offset, int len, u32 val) { + + u8 *address; + + /* + * Bus numbers are relative to hose->first_busno + */ + devfn -= PCI_BDF(hose->first_busno, 0, 0); + + /* + * Same constraints as in pcie_read_config(). + */ + if (PCI_BUS(devfn) >= 16) + return 0; + + if ((!((PCI_FUNC(devfn) == 0) && (PCI_DEV(devfn) == 0))) && + ((PCI_BUS(devfn) == 0) || (PCI_BUS(devfn) == 1))) + return 0; + + address = pcie_get_base(hose, devfn); + offset += devfn << 4; + + /* + * Suppress MCK exceptions, similar to pcie_read_config() + */ + pcie_dmer_disable (); + + switch (len) { + case 1: + out_8(hose->cfg_data + offset, val); + break; + case 2: + out_le16((u16 *)(hose->cfg_data + offset), val); + break; + default: + out_le32((u32 *)(hose->cfg_data + offset), val); + break; + } + + pcie_dmer_enable (); + + return 0; +} + +int pcie_read_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 *val) +{ + u32 v; + int rv; + + rv = pcie_read_config(hose, dev, offset, 1, &v); + *val = (u8)v; + return rv; +} + +int pcie_read_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 *val) +{ + u32 v; + int rv; + + rv = pcie_read_config(hose, dev, offset, 2, &v); + *val = (u16)v; + return rv; +} + +int pcie_read_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 *val) +{ + u32 v; + int rv; + + rv = pcie_read_config(hose, dev, offset, 3, &v); + *val = (u32)v; + return rv; +} + +int pcie_write_config_byte(struct pci_controller *hose,pci_dev_t dev,int offset,u8 val) +{ + return pcie_write_config(hose,(u32)dev,offset,1,val); +} + +int pcie_write_config_word(struct pci_controller *hose,pci_dev_t dev,int offset,u16 val) +{ + return pcie_write_config(hose,(u32)dev,offset,2,(u32 )val); +} + +int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset,u32 val) +{ + return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val); +} + +static void ppc440spe_setup_utl(u32 port) { + + volatile void *utl_base = NULL; + + /* + * Map UTL registers + */ + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE0), 0x20000000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0x68782800); + break; + + case 1: + mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE1), 0x20001000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0x68782800); + break; + + case 2: + mtdcr(DCRN_PEGPL_REGBAH(PCIE2), 0x0000000c); + mtdcr(DCRN_PEGPL_REGBAL(PCIE2), 0x20002000); + mtdcr(DCRN_PEGPL_REGMSK(PCIE2), 0x00007001); + mtdcr(DCRN_PEGPL_SPECIAL(PCIE2), 0x68782800); + break; + } + utl_base = (unsigned int *)(CFG_PCIE_BASE + 0x1000 * port); + + /* + * Set buffer allocations and then assert VRB and TXE. + */ + out_be32(utl_base + PEUTL_OUTTR, 0x08000000); + out_be32(utl_base + PEUTL_INTR, 0x02000000); + out_be32(utl_base + PEUTL_OPDBSZ, 0x10000000); + out_be32(utl_base + PEUTL_PBBSZ, 0x53000000); + out_be32(utl_base + PEUTL_IPHBSZ, 0x08000000); + out_be32(utl_base + PEUTL_IPDBSZ, 0x10000000); + out_be32(utl_base + PEUTL_RCIRQEN, 0x00f00000); + out_be32(utl_base + PEUTL_PCTL, 0x80800066); +} + +static int check_error(void) +{ + u32 valPE0, valPE1, valPE2; + int err = 0; + + /* SDR0_PEGPLLLCT1 reset */ + if (!(valPE0 = SDR_READ(PESDR0_PLLLCT1) & 0x01000000)) { + printf("PCIE: SDR0_PEGPLLLCT1 reset error 0x%x\n", valPE0); + } + + valPE0 = SDR_READ(PESDR0_RCSSET); + valPE1 = SDR_READ(PESDR1_RCSSET); + valPE2 = SDR_READ(PESDR2_RCSSET); + + /* SDR0_PExRCSSET rstgu */ + if (!(valPE0 & 0x01000000) || + !(valPE1 & 0x01000000) || + !(valPE2 & 0x01000000)) { + printf("PCIE: SDR0_PExRCSSET rstgu error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rstdl */ + if (!(valPE0 & 0x00010000) || + !(valPE1 & 0x00010000) || + !(valPE2 & 0x00010000)) { + printf("PCIE: SDR0_PExRCSSET rstdl error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rstpyn */ + if ((valPE0 & 0x00001000) || + (valPE1 & 0x00001000) || + (valPE2 & 0x00001000)) { + printf("PCIE: SDR0_PExRCSSET rstpyn error\n"); + err = -1; + } + + /* SDR0_PExRCSSET hldplb */ + if ((valPE0 & 0x10000000) || + (valPE1 & 0x10000000) || + (valPE2 & 0x10000000)) { + printf("PCIE: SDR0_PExRCSSET hldplb error\n"); + err = -1; + } + + /* SDR0_PExRCSSET rdy */ + if ((valPE0 & 0x00100000) || + (valPE1 & 0x00100000) || + (valPE2 & 0x00100000)) { + printf("PCIE: SDR0_PExRCSSET rdy error\n"); + err = -1; + } + + /* SDR0_PExRCSSET shutdown */ + if ((valPE0 & 0x00000100) || + (valPE1 & 0x00000100) || + (valPE2 & 0x00000100)) { + printf("PCIE: SDR0_PExRCSSET shutdown error\n"); + err = -1; + } + return err; +} + +/* + * Initialize PCI Express core + */ +int ppc440spe_init_pcie(void) +{ + int time_out = 20; + + /* Set PLL clock receiver to LVPECL */ + SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) | 1 << 28); + + if (check_error()) + return -1; + + if (!(SDR_READ(PESDR0_PLLLCT2) & 0x10000)) + { + printf("PCIE: PESDR_PLLCT2 resistance calibration failed (0x%08x)\n", + SDR_READ(PESDR0_PLLLCT2)); + return -1; + } + /* De-assert reset of PCIe PLL, wait for lock */ + SDR_WRITE(PESDR0_PLLLCT1, SDR_READ(PESDR0_PLLLCT1) & ~(1 << 24)); + udelay(3); + + while (time_out) { + if (!(SDR_READ(PESDR0_PLLLCT3) & 0x10000000)) { + time_out--; + udelay(1); + } else + break; + } + if (!time_out) { + printf("PCIE: VCO output not locked\n"); + return -1; + } + return 0; +} + +/* + * Yucca board as End point and root point setup + * and + * testing inbound and out bound windows + * + * YUCCA board can be plugged into another yucca board or you can get PCI-E + * cable which can be used to setup loop back from one port to another port. + * Please rememeber that unless there is a endpoint plugged in to root port it + * will not initialize. It is the same in case of endpoint , unless there is + * root port attached it will not initialize. + * + * In this release of software all the PCI-E ports are configured as either + * endpoint or rootpoint.In future we will have support for selective ports + * setup as endpoint and root point in single board. + * + * Once your board came up as root point , you can verify by reading + * /proc/bus/pci/devices. Where you can see the configuration registers + * of end point device attached to the port. + * + * Enpoint cofiguration can be verified by connecting Yucca board to any + * host or another yucca board. Then try to scan the device. In case of + * linux use "lspci" or appripriate os command. + * + * How do I verify the inbound and out bound windows ?(yucca to yucca) + * in this configuration inbound and outbound windows are setup to access + * sram memroy area. SRAM is at 0x4 0000 0000 , on PLB bus. This address + * is mapped at 0x90000000. From u-boot prompt write data 0xb000 0000, + * This is waere your POM(PLB out bound memory window) mapped. then + * read the data from other yucca board's u-boot prompt at address + * 0x9000 0000(SRAM). Data should match. + * In case of inbound , write data to u-boot command prompt at 0xb000 0000 + * which is mapped to 0x4 0000 0000. Now on rootpoint yucca u-boot prompt check + * data at 0x9000 0000(SRAM).Data should match. + */ +int ppc440spe_init_pcie_rootport(int port) +{ + static int core_init; + volatile u32 val = 0; + int attempts; + + if (!core_init) { + ++core_init; + if (ppc440spe_init_pcie()) + return -1; + } + + /* + * Initialize various parts of the PCI Express core for our port: + * + * - Set as a root port and enable max width + * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). + * - Set up UTL configuration. + * - Increase SERDES drive strength to levels suggested by AMCC. + * - De-assert RSTPYN, RSTDL and RSTGU. + * + * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with + * default setting 0x11310000. The register has new fields, + * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core + * hang. + */ + switch (port) { + case 0: + SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12); + + SDR_WRITE(PESDR0_UTLSET1, 0x21222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR0_UTLSET2, 0x11000000); + SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); + SDR_WRITE(PESDR0_RCSSET, + (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 1: + SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); + SDR_WRITE(PESDR1_UTLSET1, 0x21222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR1_UTLSET2, 0x11000000); + SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR1_RCSSET, + (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 2: + SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); + SDR_WRITE(PESDR2_UTLSET1, 0x21222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR2_UTLSET2, 0x11000000); + SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR2_RCSSET, + (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + } + /* + * Notice: the following delay has critical impact on device + * initialization - if too short (<50ms) the link doesn't get up. + */ + mdelay(100); + + switch (port) { + case 0: + val = SDR_READ(PESDR0_RCSSTS); + break; + case 1: + val = SDR_READ(PESDR1_RCSSTS); + break; + case 2: + val = SDR_READ(PESDR2_RCSSTS); + break; + } + + if (val & (1 << 20)) { + printf("PCIE%d: PGRST failed %08x\n", port, val); + return -1; + } + + /* + * Verify link is up + */ + val = 0; + switch (port) { + case 0: + val = SDR_READ(PESDR0_LOOP); + break; + case 1: + val = SDR_READ(PESDR1_LOOP); + break; + case 2: + val = SDR_READ(PESDR2_LOOP); + break; + } + if (!(val & 0x00001000)) { + printf("PCIE%d: link is not up.\n", port); + return -1; + } + + /* + * Setup UTL registers - but only on revA! + * We use default settings for revB chip. + */ + if (!ppc440spe_revB()) + ppc440spe_setup_utl(port); + + /* + * We map PCI Express configuration access into the 512MB regions + * + * NOTICE: revB is very strict about PLB real addressess and ranges to + * be mapped for config space; it seems to only work with d_nnnn_nnnn + * range (hangs the core upon config transaction attempts when set + * otherwise) while revA uses c_nnnn_nnnn. + * + * For revA: + * PCIE0: 0xc_4000_0000 + * PCIE1: 0xc_8000_0000 + * PCIE2: 0xc_c000_0000 + * + * For revB: + * PCIE0: 0xd_0000_0000 + * PCIE1: 0xd_2000_0000 + * PCIE2: 0xd_4000_0000 + */ + + switch (port) { + case 0: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); + } else { + /* revA */ + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ + break; + + case 1: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); + } else { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ + break; + + case 2: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); + } else { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ + break; + } + + /* + * Check for VC0 active and assert RDY. + */ + attempts = 10; + switch (port) { + case 0: + while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE0: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); + break; + case 1: + while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE1: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + + SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); + break; + case 2: + while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE2: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + + SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); + break; + } + mdelay(100); + + return 0; +} + +int ppc440spe_init_pcie_endport(int port) +{ + static int core_init; + volatile u32 val = 0; + int attempts; + + if (!core_init) { + ++core_init; + if (ppc440spe_init_pcie()) + return -1; + } + + /* + * Initialize various parts of the PCI Express core for our port: + * + * - Set as a end port and enable max width + * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). + * - Set up UTL configuration. + * - Increase SERDES drive strength to levels suggested by AMCC. + * - De-assert RSTPYN, RSTDL and RSTGU. + * + * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with + * default setting 0x11310000. The register has new fields, + * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core + * hang. + */ + switch (port) { + case 0: + SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X8 << 12); + + SDR_WRITE(PESDR0_UTLSET1, 0x20222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR0_UTLSET2, 0x11000000); + SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); + SDR_WRITE(PESDR0_RCSSET, + (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 1: + SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); + SDR_WRITE(PESDR1_UTLSET1, 0x20222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR1_UTLSET2, 0x11000000); + SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR1_RCSSET, + (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + + case 2: + SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); + SDR_WRITE(PESDR2_UTLSET1, 0x20222222); + if (!ppc440spe_revB()) + SDR_WRITE(PESDR2_UTLSET2, 0x11000000); + SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); + SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); + SDR_WRITE(PESDR2_RCSSET, + (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); + break; + } + /* + * Notice: the following delay has critical impact on device + * initialization - if too short (<50ms) the link doesn't get up. + */ + mdelay(100); + + switch (port) { + case 0: val = SDR_READ(PESDR0_RCSSTS); break; + case 1: val = SDR_READ(PESDR1_RCSSTS); break; + case 2: val = SDR_READ(PESDR2_RCSSTS); break; + } + + if (val & (1 << 20)) { + printf("PCIE%d: PGRST failed %08x\n", port, val); + return -1; + } + + /* + * Verify link is up + */ + val = 0; + switch (port) + { + case 0: + val = SDR_READ(PESDR0_LOOP); + break; + case 1: + val = SDR_READ(PESDR1_LOOP); + break; + case 2: + val = SDR_READ(PESDR2_LOOP); + break; + } + if (!(val & 0x00001000)) { + printf("PCIE%d: link is not up.\n", port); + return -1; + } + + /* + * Setup UTL registers - but only on revA! + * We use default settings for revB chip. + */ + if (!ppc440spe_revB()) + ppc440spe_setup_utl(port); + + /* + * We map PCI Express configuration access into the 512MB regions + * + * NOTICE: revB is very strict about PLB real addressess and ranges to + * be mapped for config space; it seems to only work with d_nnnn_nnnn + * range (hangs the core upon config transaction attempts when set + * otherwise) while revA uses c_nnnn_nnnn. + * + * For revA: + * PCIE0: 0xc_4000_0000 + * PCIE1: 0xc_8000_0000 + * PCIE2: 0xc_c000_0000 + * + * For revB: + * PCIE0: 0xd_0000_0000 + * PCIE1: 0xd_2000_0000 + * PCIE2: 0xd_4000_0000 + */ + switch (port) { + case 0: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); + } else { + /* revA */ + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ + break; + + case 1: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); + } else { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ + break; + + case 2: + if (ppc440spe_revB()) { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); + } else { + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); + } + mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ + break; + } + + /* + * Check for VC0 active and assert RDY. + */ + attempts = 10; + switch (port) { + case 0: + while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE0: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); + break; + case 1: + while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE1: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + + SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); + break; + case 2: + while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE2: VC0 not active\n"); + return -1; + } + mdelay(1000); + } + + SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); + break; + } + mdelay(100); + + return 0; +} + +void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port) +{ + volatile void *mbase = NULL; + volatile void *rmbase = NULL; + + pci_set_ops(hose, + pcie_read_config_byte, + pcie_read_config_word, + pcie_read_config_dword, + pcie_write_config_byte, + pcie_write_config_word, + pcie_write_config_dword); + + switch (port) { + case 0: + mbase = (u32 *)CFG_PCIE0_XCFGBASE; + rmbase = (u32 *)CFG_PCIE0_CFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE; + break; + case 1: + mbase = (u32 *)CFG_PCIE1_XCFGBASE; + rmbase = (u32 *)CFG_PCIE1_CFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; + break; + case 2: + mbase = (u32 *)CFG_PCIE2_XCFGBASE; + rmbase = (u32 *)CFG_PCIE2_CFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; + break; + } + + /* + * Set bus numbers on our root port + */ + out_8((u8 *)mbase + PCI_PRIMARY_BUS, 0); + out_8((u8 *)mbase + PCI_SECONDARY_BUS, 1); + out_8((u8 *)mbase + PCI_SUBORDINATE_BUS, 1); + + /* + * Set up outbound translation to hose->mem_space from PLB + * addresses at an offset of 0xd_0000_0000. We set the low + * bits of the mask to 11 to turn off splitting into 8 + * subregions and to enable the outbound translation. + */ + out_le32(mbase + PECFG_POM0LAH, 0x00000000); + out_le32(mbase + PECFG_POM0LAL, 0x00000000); + + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + case 1: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + case 2: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + } + + /* Set up 16GB inbound memory window at 0 */ + out_le32(mbase + PCI_BASE_ADDRESS_0, 0); + out_le32(mbase + PCI_BASE_ADDRESS_1, 0); + out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); + out_le32(mbase + PECFG_BAR0LMPA, 0); + + out_le32(mbase + PECFG_PIM01SAH, 0xffff0000); + out_le32(mbase + PECFG_PIM01SAL, 0x00000000); + out_le32(mbase + PECFG_PIM0LAL, 0); + out_le32(mbase + PECFG_PIM0LAH, 0); + out_le32(mbase + PECFG_PIM1LAL, 0x00000000); + out_le32(mbase + PECFG_PIM1LAH, 0x00000004); + out_le32(mbase + PECFG_PIMEN, 0x1); + + /* Enable I/O, Mem, and Busmaster cycles */ + out_le16((u16 *)(mbase + PCI_COMMAND), + in_le16((u16 *)(mbase + PCI_COMMAND)) | + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + printf("PCIE:%d successfully set as rootpoint\n",port); + + /* Set Device and Vendor Id */ + switch (port) { + case 0: + out_le16(mbase + 0x200, 0xaaa0); + out_le16(mbase + 0x202, 0xbed0); + break; + case 1: + out_le16(mbase + 0x200, 0xaaa1); + out_le16(mbase + 0x202, 0xbed1); + break; + case 2: + out_le16(mbase + 0x200, 0xaaa2); + out_le16(mbase + 0x202, 0xbed2); + break; + default: + out_le16(mbase + 0x200, 0xaaa3); + out_le16(mbase + 0x202, 0xbed3); + } + + /* Set Class Code to PCI-PCI bridge and Revision Id to 1 */ + out_le32(mbase + 0x208, 0x06040001); + +} + +int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port) +{ + volatile void *mbase = NULL; + int attempts = 0; + + pci_set_ops(hose, + pcie_read_config_byte, + pcie_read_config_word, + pcie_read_config_dword, + pcie_write_config_byte, + pcie_write_config_word, + pcie_write_config_dword); + + switch (port) { + case 0: + mbase = (u32 *)CFG_PCIE0_XCFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE0_CFGBASE; + break; + case 1: + mbase = (u32 *)CFG_PCIE1_XCFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; + break; + case 2: + mbase = (u32 *)CFG_PCIE2_XCFGBASE; + hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; + break; + } + + /* + * Set up outbound translation to hose->mem_space from PLB + * addresses at an offset of 0xd_0000_0000. We set the low + * bits of the mask to 11 to turn off splitting into 8 + * subregions and to enable the outbound translation. + */ + out_le32(mbase + PECFG_POM0LAH, 0x00001ff8); + out_le32(mbase + PECFG_POM0LAL, 0x00001000); + + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + case 1: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + case 2: + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); + mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), + ~(CFG_PCIE_MEMSIZE - 1) | 3); + break; + } + + /* Set up 16GB inbound memory window at 0 */ + out_le32(mbase + PCI_BASE_ADDRESS_0, 0); + out_le32(mbase + PCI_BASE_ADDRESS_1, 0); + out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); + out_le32(mbase + PECFG_BAR0LMPA, 0); + out_le32(mbase + PECFG_PIM0LAL, 0x00000000); + out_le32(mbase + PECFG_PIM0LAH, 0x00000004); /* pointing to SRAM */ + out_le32(mbase + PECFG_PIMEN, 0x1); + + /* Enable I/O, Mem, and Busmaster cycles */ + out_le16((u16 *)(mbase + PCI_COMMAND), + in_le16((u16 *)(mbase + PCI_COMMAND)) | + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + out_le16(mbase + 0x200,0xcaad); /* Setting vendor ID */ + out_le16(mbase + 0x202,0xfeed); /* Setting device ID */ + attempts = 10; + switch (port) { + case 0: + while (!(SDR_READ(PESDR0_RCSSTS) & (1 << 8))) { + if (!(attempts--)) { + printf("PCIE0: BMEN is not active\n"); + return -1; + } + mdelay(1000); + } + break; + case 1: + while (!(SDR_READ(PESDR1_RCSSTS) & (1 << 8))) { + if (!(attempts--)) { + printf("PCIE1: BMEN is not active\n"); + return -1; + } + mdelay(1000); + } + break; + case 2: + while (!(SDR_READ(PESDR2_RCSSTS) & (1 << 8))) { + if (!(attempts--)) { + printf("PCIE2: BMEN is not active\n"); + return -1; + } + mdelay(1000); + } + break; + } + printf("PCIE:%d successfully set as endpoint\n",port); + + return 0; +} +#endif /* CONFIG_440SPE && CONFIG_PCI */ diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index af9da5b95fd..28a8e2bcb7e 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -27,13 +27,12 @@ LIB = $(obj)lib$(CPU).a START = start.o resetvec.o kgdb.o SOBJS = dcr.o -COBJS = 405gp_pci.o 440spe_pcie.o 4xx_enet.o \ +COBJS = 405gp_pci.o 4xx_pcie.o 4xx_enet.o \ bedbug_405.o commproc.o \ cpu.o cpu_init.o gpio.o i2c.o interrupts.o \ miiphy.o ndfc.o sdram.o serial.o \ 40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o speed.o \ - tlb.o traps.o usb_ohci.o usb.o usbdev.o \ - 440spe_pcie.o + tlb.o traps.o usb_ohci.o usb.o usbdev.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h new file mode 100644 index 00000000000..38745eb797c --- /dev/null +++ b/include/asm-ppc/4xx_pcie.h @@ -0,0 +1,174 @@ +/* + * Copyright (c) 2005 Cisco Systems. All rights reserved. + * Roland Dreier + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#include +#ifndef __440SPE_PCIE_H +#define __440SPE_PCIE_H + +#define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);}) + +#define DCRN_SDR0_CFGADDR 0x00e +#define DCRN_SDR0_CFGDATA 0x00f + +#define DCRN_PCIE0_BASE 0x100 +#define DCRN_PCIE1_BASE 0x120 +#define DCRN_PCIE2_BASE 0x140 +#define PCIE0 DCRN_PCIE0_BASE +#define PCIE1 DCRN_PCIE1_BASE +#define PCIE2 DCRN_PCIE2_BASE + +#define DCRN_PEGPL_CFGBAH(base) (base + 0x00) +#define DCRN_PEGPL_CFGBAL(base) (base + 0x01) +#define DCRN_PEGPL_CFGMSK(base) (base + 0x02) +#define DCRN_PEGPL_MSGBAH(base) (base + 0x03) +#define DCRN_PEGPL_MSGBAL(base) (base + 0x04) +#define DCRN_PEGPL_MSGMSK(base) (base + 0x05) +#define DCRN_PEGPL_OMR1BAH(base) (base + 0x06) +#define DCRN_PEGPL_OMR1BAL(base) (base + 0x07) +#define DCRN_PEGPL_OMR1MSKH(base) (base + 0x08) +#define DCRN_PEGPL_OMR1MSKL(base) (base + 0x09) +#define DCRN_PEGPL_REGBAH(base) (base + 0x12) +#define DCRN_PEGPL_REGBAL(base) (base + 0x13) +#define DCRN_PEGPL_REGMSK(base) (base + 0x14) +#define DCRN_PEGPL_SPECIAL(base) (base + 0x15) +#define DCRN_PEGPL_CFG(base) (base + 0x16) + +/* + * System DCRs (SDRs) + */ +#define PESDR0_PLLLCT1 0x03a0 +#define PESDR0_PLLLCT2 0x03a1 +#define PESDR0_PLLLCT3 0x03a2 + +#define PESDR0_UTLSET1 0x0300 +#define PESDR0_UTLSET2 0x0301 +#define PESDR0_DLPSET 0x0302 +#define PESDR0_LOOP 0x0303 +#define PESDR0_RCSSET 0x0304 +#define PESDR0_RCSSTS 0x0305 +#define PESDR0_HSSL0SET1 0x0306 +#define PESDR0_HSSL0SET2 0x0307 +#define PESDR0_HSSL0STS 0x0308 +#define PESDR0_HSSL1SET1 0x0309 +#define PESDR0_HSSL1SET2 0x030a +#define PESDR0_HSSL1STS 0x030b +#define PESDR0_HSSL2SET1 0x030c +#define PESDR0_HSSL2SET2 0x030d +#define PESDR0_HSSL2STS 0x030e +#define PESDR0_HSSL3SET1 0x030f +#define PESDR0_HSSL3SET2 0x0310 +#define PESDR0_HSSL3STS 0x0311 +#define PESDR0_HSSL4SET1 0x0312 +#define PESDR0_HSSL4SET2 0x0313 +#define PESDR0_HSSL4STS 0x0314 +#define PESDR0_HSSL5SET1 0x0315 +#define PESDR0_HSSL5SET2 0x0316 +#define PESDR0_HSSL5STS 0x0317 +#define PESDR0_HSSL6SET1 0x0318 +#define PESDR0_HSSL6SET2 0x0319 +#define PESDR0_HSSL6STS 0x031a +#define PESDR0_HSSL7SET1 0x031b +#define PESDR0_HSSL7SET2 0x031c +#define PESDR0_HSSL7STS 0x031d +#define PESDR0_HSSCTLSET 0x031e +#define PESDR0_LANE_ABCD 0x031f +#define PESDR0_LANE_EFGH 0x0320 + +#define PESDR1_UTLSET1 0x0340 +#define PESDR1_UTLSET2 0x0341 +#define PESDR1_DLPSET 0x0342 +#define PESDR1_LOOP 0x0343 +#define PESDR1_RCSSET 0x0344 +#define PESDR1_RCSSTS 0x0345 +#define PESDR1_HSSL0SET1 0x0346 +#define PESDR1_HSSL0SET2 0x0347 +#define PESDR1_HSSL0STS 0x0348 +#define PESDR1_HSSL1SET1 0x0349 +#define PESDR1_HSSL1SET2 0x034a +#define PESDR1_HSSL1STS 0x034b +#define PESDR1_HSSL2SET1 0x034c +#define PESDR1_HSSL2SET2 0x034d +#define PESDR1_HSSL2STS 0x034e +#define PESDR1_HSSL3SET1 0x034f +#define PESDR1_HSSL3SET2 0x0350 +#define PESDR1_HSSL3STS 0x0351 +#define PESDR1_HSSCTLSET 0x0352 +#define PESDR1_LANE_ABCD 0x0353 + +#define PESDR2_UTLSET1 0x0370 +#define PESDR2_UTLSET2 0x0371 +#define PESDR2_DLPSET 0x0372 +#define PESDR2_LOOP 0x0373 +#define PESDR2_RCSSET 0x0374 +#define PESDR2_RCSSTS 0x0375 +#define PESDR2_HSSL0SET1 0x0376 +#define PESDR2_HSSL0SET2 0x0377 +#define PESDR2_HSSL0STS 0x0378 +#define PESDR2_HSSL1SET1 0x0379 +#define PESDR2_HSSL1SET2 0x037a +#define PESDR2_HSSL1STS 0x037b +#define PESDR2_HSSL2SET1 0x037c +#define PESDR2_HSSL2SET2 0x037d +#define PESDR2_HSSL2STS 0x037e +#define PESDR2_HSSL3SET1 0x037f +#define PESDR2_HSSL3SET2 0x0380 +#define PESDR2_HSSL3STS 0x0381 +#define PESDR2_HSSCTLSET 0x0382 +#define PESDR2_LANE_ABCD 0x0383 + +/* + * UTL register offsets + */ +#define PEUTL_PBBSZ 0x20 +#define PEUTL_OPDBSZ 0x68 +#define PEUTL_IPHBSZ 0x70 +#define PEUTL_IPDBSZ 0x78 +#define PEUTL_OUTTR 0x90 +#define PEUTL_INTR 0x98 +#define PEUTL_PCTL 0xa0 +#define PEUTL_RCIRQEN 0xb8 + +/* + * Config space register offsets + */ +#define PECFG_BAR0LMPA 0x210 +#define PECFG_BAR0HMPA 0x214 +#define PECFG_BAR1MPA 0x218 +#define PECFG_BAR2MPA 0x220 + +#define PECFG_PIMEN 0x33c +#define PECFG_PIM0LAL 0x340 +#define PECFG_PIM0LAH 0x344 +#define PECFG_PIM1LAL 0x348 +#define PECFG_PIM1LAH 0x34c +#define PECFG_PIM01SAL 0x350 +#define PECFG_PIM01SAH 0x354 + +#define PECFG_POM0LAL 0x380 +#define PECFG_POM0LAH 0x384 + +#define SDR_READ(offset) ({\ + mtdcr(DCRN_SDR0_CFGADDR, offset); \ + mfdcr(DCRN_SDR0_CFGDATA);}) + +#define SDR_WRITE(offset, data) ({\ + mtdcr(DCRN_SDR0_CFGADDR, offset); \ + mtdcr(DCRN_SDR0_CFGDATA,data);}) + +#define GPL_DMER_MASK_DISA 0x02000000 + +int ppc440spe_init_pcie(void); +int ppc440spe_init_pcie_rootport(int port); +void yucca_setup_pcie_fpga_rootpoint(int port); +void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port); +int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port); +int yucca_pcie_card_present(int port); +int pcie_hose_scan(struct pci_controller *hose, int bus); +#endif /* __440SPE_PCIE_H */ -- cgit v1.3.1 From 026f71106871f31d17d0ea0db9a7547ff92934bc Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 3 Oct 2007 07:48:09 +0200 Subject: ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (2) This patch is the first patch of a series to make the 440SPe PCIe code usable on different 4xx PPC platforms. In preperation for the new 405EX which is also equipped with PCIe interfaces. (2) This patch renames the functions from 440spe_ to 4xx_ with a little additional cleanup Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 11 ++++------- board/amcc/yucca/yucca.c | 11 ++++------- cpu/ppc4xx/4xx_pcie.c | 20 ++++++++++---------- include/asm-ppc/4xx_pcie.h | 17 ++++++++--------- 4 files changed, 26 insertions(+), 33 deletions(-) (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index 0c8e6cb701e..f1c352cb86e 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -35,9 +35,6 @@ DECLARE_GLOBAL_DATA_PTR; -int ppc440spe_init_pcie_rootport(int port); -void ppc440spe_setup_pcie(struct pci_controller *hose, int port); - int board_early_init_f (void) { unsigned long mfr; @@ -409,9 +406,9 @@ void pcie_setup_hoses(int busno) continue; #ifdef PCIE_ENDPOINT - if (ppc440spe_init_pcie_endport(i)) { + if (ppc4xx_init_pcie_endport(i)) { #else - if (ppc440spe_init_pcie_rootport(i)) { + if (ppc4xx_init_pcie_rootport(i)) { #endif printf("PCIE%d: initialization failed\n", i); continue; @@ -433,13 +430,13 @@ void pcie_setup_hoses(int busno) pci_register_hose(hose); #ifdef PCIE_ENDPOINT - ppc440spe_setup_pcie_endpoint(hose, i); + ppc4xx_setup_pcie_endpoint(hose, i); /* * Reson for no scanning is endpoint can not generate * upstream configuration accesses. */ #else - ppc440spe_setup_pcie_rootpoint(hose, i); + ppc4xx_setup_pcie_rootpoint(hose, i); env = getenv ("pciscandelay"); if (env != NULL) { diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index 17c3ba0f17d..c46721c9229 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -47,9 +47,6 @@ char *remove_l_w_space(char *in_str ); char *remove_t_w_space(char *in_str ); int get_console_port(void); -int ppc440spe_init_pcie_rootport(int port); -void ppc440spe_setup_pcie(struct pci_controller *hose, int port); - #define DEBUG_ENV #ifdef DEBUG_ENV #define DEBUGF(fmt,args...) printf(fmt ,##args) @@ -865,10 +862,10 @@ void pcie_setup_hoses(int busno) #ifdef PCIE_ENDPOINT yucca_setup_pcie_fpga_endpoint(i); - if (ppc440spe_init_pcie_endport(i)) { + if (ppc4xx_init_pcie_endport(i)) { #else yucca_setup_pcie_fpga_rootpoint(i); - if (ppc440spe_init_pcie_rootport(i)) { + if (ppc4xx_init_pcie_rootport(i)) { #endif printf("PCIE%d: initialization failed\n", i); continue; @@ -890,13 +887,13 @@ void pcie_setup_hoses(int busno) pci_register_hose(hose); #ifdef PCIE_ENDPOINT - ppc440spe_setup_pcie_endpoint(hose, i); + ppc4xx_setup_pcie_endpoint(hose, i); /* * Reson for no scanning is endpoint can not generate * upstream configuration accesses. */ #else - ppc440spe_setup_pcie_rootpoint(hose, i); + ppc4xx_setup_pcie_rootpoint(hose, i); env = getenv ("pciscandelay"); if (env != NULL) { diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index 8906adc51e2..c7b21417861 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -222,7 +222,7 @@ int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val); } -static void ppc440spe_setup_utl(u32 port) { +static void ppc4xx_setup_utl(u32 port) { volatile void *utl_base = NULL; @@ -333,7 +333,7 @@ static int check_error(void) /* * Initialize PCI Express core */ -int ppc440spe_init_pcie(void) +int ppc4xx_init_pcie(void) { int time_out = 20; @@ -401,7 +401,7 @@ int ppc440spe_init_pcie(void) * which is mapped to 0x4 0000 0000. Now on rootpoint yucca u-boot prompt check * data at 0x9000 0000(SRAM).Data should match. */ -int ppc440spe_init_pcie_rootport(int port) +int ppc4xx_init_pcie_rootport(int port) { static int core_init; volatile u32 val = 0; @@ -409,7 +409,7 @@ int ppc440spe_init_pcie_rootport(int port) if (!core_init) { ++core_init; - if (ppc440spe_init_pcie()) + if (ppc4xx_init_pcie()) return -1; } @@ -520,7 +520,7 @@ int ppc440spe_init_pcie_rootport(int port) * We use default settings for revB chip. */ if (!ppc440spe_revB()) - ppc440spe_setup_utl(port); + ppc4xx_setup_utl(port); /* * We map PCI Express configuration access into the 512MB regions @@ -620,7 +620,7 @@ int ppc440spe_init_pcie_rootport(int port) return 0; } -int ppc440spe_init_pcie_endport(int port) +int ppc4xx_init_pcie_endport(int port) { static int core_init; volatile u32 val = 0; @@ -628,7 +628,7 @@ int ppc440spe_init_pcie_endport(int port) if (!core_init) { ++core_init; - if (ppc440spe_init_pcie()) + if (ppc4xx_init_pcie()) return -1; } @@ -734,7 +734,7 @@ int ppc440spe_init_pcie_endport(int port) * We use default settings for revB chip. */ if (!ppc440spe_revB()) - ppc440spe_setup_utl(port); + ppc4xx_setup_utl(port); /* * We map PCI Express configuration access into the 512MB regions @@ -833,7 +833,7 @@ int ppc440spe_init_pcie_endport(int port) return 0; } -void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port) +void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) { volatile void *mbase = NULL; volatile void *rmbase = NULL; @@ -951,7 +951,7 @@ void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port) } -int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port) +int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) { volatile void *mbase = NULL; int attempts = 0; diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index 38745eb797c..220c60cd761 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -9,8 +9,8 @@ */ #include -#ifndef __440SPE_PCIE_H -#define __440SPE_PCIE_H +#ifndef __4XX_PCIE_H +#define __4XX_PCIE_H #define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);}) @@ -164,11 +164,10 @@ #define GPL_DMER_MASK_DISA 0x02000000 -int ppc440spe_init_pcie(void); -int ppc440spe_init_pcie_rootport(int port); -void yucca_setup_pcie_fpga_rootpoint(int port); -void ppc440spe_setup_pcie_rootpoint(struct pci_controller *hose, int port); -int ppc440spe_setup_pcie_endpoint(struct pci_controller *hose, int port); -int yucca_pcie_card_present(int port); +int ppc4xx_init_pcie(void); +int ppc4xx_init_pcie_rootport(int port); +void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port); +int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port); int pcie_hose_scan(struct pci_controller *hose, int bus); -#endif /* __440SPE_PCIE_H */ + +#endif /* __4XX_PCIE_H */ -- cgit v1.3.1 From 03d344bb6a5f082ea10ec9d753558ea7dfd1c626 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 3 Oct 2007 10:38:09 +0200 Subject: ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (3) (3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access the SDR registers of the PCIe ports. This makes the overall design clearer, since it removed a lot of switch statements which are not needed anymore. Also, the functions ppc4xx_init_pcie_rootport() and ppc4xx_init_pcie_entport() are merged into a single function ppc4xx_init_pcie_port(), since most of the code was duplicated. This makes maintainance and porting to other 4xx platforms easier. Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_pcie.c | 642 ++++++++++++++++----------------------------- include/asm-ppc/4xx_pcie.h | 101 ++++++- 2 files changed, 322 insertions(+), 421 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index c7b21417861..2bc9638f414 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -368,11 +368,167 @@ int ppc4xx_init_pcie(void) } /* - * Yucca board as End point and root point setup + * Board-specific pcie initialization + * Platform code can reimplement ppc4xx_init_pcie_port_hw() if needed + */ + +/* + * Initialize various parts of the PCI Express core for our port: + * + * - Set as a root port and enable max width + * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). + * - Set up UTL configuration. + * - Increase SERDES drive strength to levels suggested by AMCC. + * - De-assert RSTPYN, RSTDL and RSTGU. + * + * NOTICE for 440SPE revB chip: PESDRn_UTLSET2 is not set - we leave it + * with default setting 0x11310000. The register has new fields, + * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core + * hang. + */ +#if defined(CONFIG_440SPE) +int __ppc4xx_init_pcie_port_hw(int port, int rootport) +{ + u32 val = 1 << 24; + u32 utlset1; + + if (rootport) { + val = PTYPE_ROOT_PORT << 20; + utlset1 = 0x21222222; + } else { + val = PTYPE_LEGACY_ENDPOINT << 20; + utlset1 = 0x20222222; + } + + if (port == 0) + val |= LNKW_X8 << 12; + else + val |= LNKW_X4 << 12; + + SDR_WRITE(SDRN_PESDR_DLPSET(port), val); + SDR_WRITE(SDRN_PESDR_UTLSET1(port), utlset1); + if (!ppc440spe_revB()) + SDR_WRITE(SDRN_PESDR_UTLSET2(port), 0x11000000); + SDR_WRITE(SDRN_PESDR_HSSL0SET1(port), 0x35000000); + SDR_WRITE(SDRN_PESDR_HSSL1SET1(port), 0x35000000); + SDR_WRITE(SDRN_PESDR_HSSL2SET1(port), 0x35000000); + SDR_WRITE(SDRN_PESDR_HSSL3SET1(port), 0x35000000); + if (port == 0) { + SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); + SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); + } + SDR_WRITE(SDRN_PESDR_RCSSET(port), (SDR_READ(SDRN_PESDR_RCSSET(port)) & + ~(1 << 24 | 1 << 16)) | 1 << 12); + + return 0; +} +#endif /* CONFIG_440SPE */ + +#if defined(CONFIG_405EX) +int __ppc4xx_init_pcie_port_hw(int port, int rootport) +{ + u32 val; + + if (rootport) + val = 0x00401000; + else + val = 0x00101000; + + SDR_WRITE(SDRN_PESDR_DLPSET(port), val); + SDR_WRITE(SDRN_PESDR_UTLSET1(port), 0x20222222); + SDR_WRITE(SDRN_PESDR_UTLSET2(port), 0x01110000); + SDR_WRITE(SDRN_PESDR_PHYSET1(port), 0x720F0000); + SDR_WRITE(SDRN_PESDR_PHYSET2(port), 0x70600003); + + /* Assert the PE0_PHY reset */ + SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x01010000); + udelay(1000); + + /* deassert the PE0_hotreset */ + SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x01101000); + + /* poll for phy !reset */ + while (!(SDR_READ(SDRN_PESDR_PHYSTA(port)) & 0x00001000)) + ; + + /* deassert the PE0_gpl_utl_reset */ + SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x00101000); + + if (port == 0) + mtdcr(DCRN_PEGPL_CFG(PCIE0), 0x10000000); /* guarded on */ + else + mtdcr(DCRN_PEGPL_CFG(PCIE1), 0x10000000); /* guarded on */ + + return 0; +} +#endif /* CONFIG_405EX */ + +int ppc4xx_init_pcie_port_hw(int port, int rootport) + __attribute__((weak, alias("__ppc4xx_init_pcie_port_hw"))); + +/* + * We map PCI Express configuration access into the 512MB regions + * + * NOTICE: revB is very strict about PLB real addressess and ranges to + * be mapped for config space; it seems to only work with d_nnnn_nnnn + * range (hangs the core upon config transaction attempts when set + * otherwise) while revA uses c_nnnn_nnnn. + * + * For revA: + * PCIE0: 0xc_4000_0000 + * PCIE1: 0xc_8000_0000 + * PCIE2: 0xc_c000_0000 + * + * For revB: + * PCIE0: 0xd_0000_0000 + * PCIE1: 0xd_2000_0000 + * PCIE2: 0xd_4000_0000 + * + * For 405EX: + * PCIE0: 0xa000_0000 + * PCIE1: 0xc000_0000 + */ +static inline u64 ppc4xx_get_cfgaddr(int port) +{ +#if defined(CONFIG_405EX) + if (port == 0) + return (u64)CFG_PCIE0_CFGBASE; + else + return (u64)CFG_PCIE1_CFGBASE; +#endif +#if defined(CONFIG_440SPE) + if (ppc440spe_revB()) { + switch (port) { + default: /* to satisfy compiler */ + case 0: + return 0x0000000d00000000ULL; + case 1: + return 0x0000000d20000000ULL; + case 2: + return 0x0000000d40000000ULL; + } + } else { + switch (port) { + default: /* to satisfy compiler */ + case 0: + return 0x0000000c40000000ULL; + case 1: + return 0x0000000c80000000ULL; + case 2: + return 0x0000000cc0000000ULL; + } + } +#endif +} + +/* + * 4xx boards as end point and root point setup * and * testing inbound and out bound windows * - * YUCCA board can be plugged into another yucca board or you can get PCI-E + * 4xx boards can be plugged into another 4xx boards or you can get PCI-E * cable which can be used to setup loop back from one port to another port. * Please rememeber that unless there is a endpoint plugged in to root port it * will not initialize. It is the same in case of endpoint , unless there is @@ -386,26 +542,28 @@ int ppc4xx_init_pcie(void) * /proc/bus/pci/devices. Where you can see the configuration registers * of end point device attached to the port. * - * Enpoint cofiguration can be verified by connecting Yucca board to any - * host or another yucca board. Then try to scan the device. In case of + * Enpoint cofiguration can be verified by connecting 4xx board to any + * host or another 4xx board. Then try to scan the device. In case of * linux use "lspci" or appripriate os command. * - * How do I verify the inbound and out bound windows ?(yucca to yucca) + * How do I verify the inbound and out bound windows ? (4xx to 4xx) * in this configuration inbound and outbound windows are setup to access * sram memroy area. SRAM is at 0x4 0000 0000 , on PLB bus. This address * is mapped at 0x90000000. From u-boot prompt write data 0xb000 0000, * This is waere your POM(PLB out bound memory window) mapped. then - * read the data from other yucca board's u-boot prompt at address + * read the data from other 4xx board's u-boot prompt at address * 0x9000 0000(SRAM). Data should match. * In case of inbound , write data to u-boot command prompt at 0xb000 0000 * which is mapped to 0x4 0000 0000. Now on rootpoint yucca u-boot prompt check * data at 0x9000 0000(SRAM).Data should match. */ -int ppc4xx_init_pcie_rootport(int port) +int ppc4xx_init_pcie_port(int port, int rootport) { static int core_init; volatile u32 val = 0; int attempts; + u64 addr; + u32 low, high; if (!core_init) { ++core_init; @@ -414,82 +572,17 @@ int ppc4xx_init_pcie_rootport(int port) } /* - * Initialize various parts of the PCI Express core for our port: - * - * - Set as a root port and enable max width - * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). - * - Set up UTL configuration. - * - Increase SERDES drive strength to levels suggested by AMCC. - * - De-assert RSTPYN, RSTDL and RSTGU. - * - * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with - * default setting 0x11310000. The register has new fields, - * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core - * hang. + * Initialize various parts of the PCI Express core for our port */ - switch (port) { - case 0: - SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X8 << 12); - - SDR_WRITE(PESDR0_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR0_UTLSET2, 0x11000000); - SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); - SDR_WRITE(PESDR0_RCSSET, - (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; + ppc4xx_init_pcie_port_hw(port, rootport); - case 1: - SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR1_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR1_UTLSET2, 0x11000000); - SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR1_RCSSET, - (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 2: - SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_ROOT_PORT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR2_UTLSET1, 0x21222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR2_UTLSET2, 0x11000000); - SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR2_RCSSET, - (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - } /* * Notice: the following delay has critical impact on device * initialization - if too short (<50ms) the link doesn't get up. */ mdelay(100); - switch (port) { - case 0: - val = SDR_READ(PESDR0_RCSSTS); - break; - case 1: - val = SDR_READ(PESDR1_RCSSTS); - break; - case 2: - val = SDR_READ(PESDR2_RCSSTS); - break; - } - + val = SDR_READ(SDRN_PESDR_RCSSTS(sdr_base(port))); if (val & (1 << 20)) { printf("PCIE%d: PGRST failed %08x\n", port, val); return -1; @@ -498,18 +591,7 @@ int ppc4xx_init_pcie_rootport(int port) /* * Verify link is up */ - val = 0; - switch (port) { - case 0: - val = SDR_READ(PESDR0_LOOP); - break; - case 1: - val = SDR_READ(PESDR1_LOOP); - break; - case 2: - val = SDR_READ(PESDR2_LOOP); - break; - } + val = SDR_READ(SDRN_PESDR_LOOP(sdr_base(port))); if (!(val & 0x00001000)) { printf("PCIE%d: link is not up.\n", port); return -1; @@ -524,55 +606,25 @@ int ppc4xx_init_pcie_rootport(int port) /* * We map PCI Express configuration access into the 512MB regions - * - * NOTICE: revB is very strict about PLB real addressess and ranges to - * be mapped for config space; it seems to only work with d_nnnn_nnnn - * range (hangs the core upon config transaction attempts when set - * otherwise) while revA uses c_nnnn_nnnn. - * - * For revA: - * PCIE0: 0xc_4000_0000 - * PCIE1: 0xc_8000_0000 - * PCIE2: 0xc_c000_0000 - * - * For revB: - * PCIE0: 0xd_0000_0000 - * PCIE1: 0xd_2000_0000 - * PCIE2: 0xd_4000_0000 */ + addr = ppc4xx_get_cfgaddr(port); + low = (u32)(addr & 0x00000000ffffffff); + high = (u32)(addr >> 32); switch (port) { case 0: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); - } else { - /* revA */ - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); - } + mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), high); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), low); mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ break; - case 1: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); - } + mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), high); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), low); mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ break; - case 2: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); - } + mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), high); + mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), low); mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ break; } @@ -581,256 +633,28 @@ int ppc4xx_init_pcie_rootport(int port) * Check for VC0 active and assert RDY. */ attempts = 10; - switch (port) { - case 0: - while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE0: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); - break; - case 1: - while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE1: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); - break; - case 2: - while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE2: VC0 not active\n"); - return -1; - } - mdelay(1000); + while(!(SDR_READ(SDRN_PESDR_RCSSTS(sdr_base(port))) & (1 << 16))) { + if (!(attempts--)) { + printf("PCIE%d: VC0 not active\n", port); + return -1; } - - SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); - break; + mdelay(1000); } + SDR_WRITE(SDRN_PESDR_RCSSET(sdr_base(port)), + SDR_READ(SDRN_PESDR_RCSSET(sdr_base(port))) | 1 << 20); mdelay(100); return 0; } -int ppc4xx_init_pcie_endport(int port) +int ppc4xx_init_pcie_rootport(int port) { - static int core_init; - volatile u32 val = 0; - int attempts; - - if (!core_init) { - ++core_init; - if (ppc4xx_init_pcie()) - return -1; - } - - /* - * Initialize various parts of the PCI Express core for our port: - * - * - Set as a end port and enable max width - * (PXIE0 -> X8, PCIE1 and PCIE2 -> X4). - * - Set up UTL configuration. - * - Increase SERDES drive strength to levels suggested by AMCC. - * - De-assert RSTPYN, RSTDL and RSTGU. - * - * NOTICE for revB chip: PESDRn_UTLSET2 is not set - we leave it with - * default setting 0x11310000. The register has new fields, - * PESDRn_UTLSET2[LKINE] in particular: clearing it leads to PCIE core - * hang. - */ - switch (port) { - case 0: - SDR_WRITE(PESDR0_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X8 << 12); - - SDR_WRITE(PESDR0_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR0_UTLSET2, 0x11000000); - SDR_WRITE(PESDR0_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL4SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL5SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL6SET1, 0x35000000); - SDR_WRITE(PESDR0_HSSL7SET1, 0x35000000); - SDR_WRITE(PESDR0_RCSSET, - (SDR_READ(PESDR0_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 1: - SDR_WRITE(PESDR1_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR1_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR1_UTLSET2, 0x11000000); - SDR_WRITE(PESDR1_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR1_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR1_RCSSET, - (SDR_READ(PESDR1_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - - case 2: - SDR_WRITE(PESDR2_DLPSET, 1 << 24 | PTYPE_LEGACY_ENDPOINT << 20 | LNKW_X4 << 12); - SDR_WRITE(PESDR2_UTLSET1, 0x20222222); - if (!ppc440spe_revB()) - SDR_WRITE(PESDR2_UTLSET2, 0x11000000); - SDR_WRITE(PESDR2_HSSL0SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL1SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL2SET1, 0x35000000); - SDR_WRITE(PESDR2_HSSL3SET1, 0x35000000); - SDR_WRITE(PESDR2_RCSSET, - (SDR_READ(PESDR2_RCSSET) & ~(1 << 24 | 1 << 16)) | 1 << 12); - break; - } - /* - * Notice: the following delay has critical impact on device - * initialization - if too short (<50ms) the link doesn't get up. - */ - mdelay(100); - - switch (port) { - case 0: val = SDR_READ(PESDR0_RCSSTS); break; - case 1: val = SDR_READ(PESDR1_RCSSTS); break; - case 2: val = SDR_READ(PESDR2_RCSSTS); break; - } - - if (val & (1 << 20)) { - printf("PCIE%d: PGRST failed %08x\n", port, val); - return -1; - } - - /* - * Verify link is up - */ - val = 0; - switch (port) - { - case 0: - val = SDR_READ(PESDR0_LOOP); - break; - case 1: - val = SDR_READ(PESDR1_LOOP); - break; - case 2: - val = SDR_READ(PESDR2_LOOP); - break; - } - if (!(val & 0x00001000)) { - printf("PCIE%d: link is not up.\n", port); - return -1; - } - - /* - * Setup UTL registers - but only on revA! - * We use default settings for revB chip. - */ - if (!ppc440spe_revB()) - ppc4xx_setup_utl(port); - - /* - * We map PCI Express configuration access into the 512MB regions - * - * NOTICE: revB is very strict about PLB real addressess and ranges to - * be mapped for config space; it seems to only work with d_nnnn_nnnn - * range (hangs the core upon config transaction attempts when set - * otherwise) while revA uses c_nnnn_nnnn. - * - * For revA: - * PCIE0: 0xc_4000_0000 - * PCIE1: 0xc_8000_0000 - * PCIE2: 0xc_c000_0000 - * - * For revB: - * PCIE0: 0xd_0000_0000 - * PCIE1: 0xd_2000_0000 - * PCIE2: 0xd_4000_0000 - */ - switch (port) { - case 0: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x00000000); - } else { - /* revA */ - mtdcr(DCRN_PEGPL_CFGBAH(PCIE0), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE0), 0x40000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE0), 0xe0000001); /* 512MB region, valid */ - break; - - case 1: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x20000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE1), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), 0x80000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ - break; - - case 2: - if (ppc440spe_revB()) { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0x40000000); - } else { - mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), 0x0000000c); - mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), 0xc0000000); - } - mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ - break; - } - - /* - * Check for VC0 active and assert RDY. - */ - attempts = 10; - switch (port) { - case 0: - while(!(SDR_READ(PESDR0_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE0: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - SDR_WRITE(PESDR0_RCSSET, SDR_READ(PESDR0_RCSSET) | 1 << 20); - break; - case 1: - while(!(SDR_READ(PESDR1_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE1: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR1_RCSSET, SDR_READ(PESDR1_RCSSET) | 1 << 20); - break; - case 2: - while(!(SDR_READ(PESDR2_RCSSTS) & (1 << 16))) { - if (!(attempts--)) { - printf("PCIE2: VC0 not active\n"); - return -1; - } - mdelay(1000); - } - - SDR_WRITE(PESDR2_RCSSET, SDR_READ(PESDR2_RCSSET) | 1 << 20); - break; - } - mdelay(100); + return ppc4xx_init_pcie_port(port, 1); +} - return 0; +int ppc4xx_init_pcie_endport(int port) +{ + return ppc4xx_init_pcie_port(port, 0); } void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) @@ -839,12 +663,12 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) volatile void *rmbase = NULL; pci_set_ops(hose, - pcie_read_config_byte, - pcie_read_config_word, - pcie_read_config_dword, - pcie_write_config_byte, - pcie_write_config_word, - pcie_write_config_dword); + pcie_read_config_byte, + pcie_read_config_word, + pcie_read_config_dword, + pcie_write_config_byte, + pcie_write_config_word, + pcie_write_config_dword); switch (port) { case 0: @@ -884,26 +708,26 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) case 0: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE); + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; case 1: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; case 2: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; } @@ -925,7 +749,6 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) out_le16((u16 *)(mbase + PCI_COMMAND), in_le16((u16 *)(mbase + PCI_COMMAND)) | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); - printf("PCIE:%d successfully set as rootpoint\n",port); /* Set Device and Vendor Id */ switch (port) { @@ -949,6 +772,7 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) /* Set Class Code to PCI-PCI bridge and Revision Id to 1 */ out_le32(mbase + 0x208, 0x06040001); + printf("PCIE:%d successfully set as rootpoint\n", port); } int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) @@ -992,26 +816,26 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) case 0: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE); + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; case 1: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; case 2: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), (CFG_PCIE_MEMBASE + - port * CFG_PCIE_MEMSIZE)); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), - ~(CFG_PCIE_MEMSIZE - 1) | 3); + ~(CFG_PCIE_MEMSIZE - 1) | 3); break; } @@ -1026,40 +850,20 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) /* Enable I/O, Mem, and Busmaster cycles */ out_le16((u16 *)(mbase + PCI_COMMAND), - in_le16((u16 *)(mbase + PCI_COMMAND)) | - PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + in_le16((u16 *)(mbase + PCI_COMMAND)) | + PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); out_le16(mbase + 0x200,0xcaad); /* Setting vendor ID */ out_le16(mbase + 0x202,0xfeed); /* Setting device ID */ + attempts = 10; - switch (port) { - case 0: - while (!(SDR_READ(PESDR0_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE0: BMEN is not active\n"); - return -1; - } - mdelay(1000); - } - break; - case 1: - while (!(SDR_READ(PESDR1_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE1: BMEN is not active\n"); - return -1; - } - mdelay(1000); - } - break; - case 2: - while (!(SDR_READ(PESDR2_RCSSTS) & (1 << 8))) { - if (!(attempts--)) { - printf("PCIE2: BMEN is not active\n"); - return -1; - } - mdelay(1000); + while(!(SDR_READ(SDRN_PESDR_RCSSTS(sdr_base(port))) & (1 << 8))) { + if (!(attempts--)) { + printf("PCIE%d: BME not active\n", port); + return -1; } - break; + mdelay(1000); } + printf("PCIE:%d successfully set as endpoint\n",port); return 0; diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index 220c60cd761..1bb8fc7ed13 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -12,14 +12,20 @@ #ifndef __4XX_PCIE_H #define __4XX_PCIE_H -#define mdelay(n) ({unsigned long __ms=(n); while (__ms--) udelay(1000);}) - #define DCRN_SDR0_CFGADDR 0x00e #define DCRN_SDR0_CFGDATA 0x00f +#if defined(CONFIG_440SPE) #define DCRN_PCIE0_BASE 0x100 #define DCRN_PCIE1_BASE 0x120 #define DCRN_PCIE2_BASE 0x140 +#endif + +#if defined(CONFIG_405EX) +#define DCRN_PCIE0_BASE 0x040 +#define DCRN_PCIE1_BASE 0x060 +#endif + #define PCIE0 DCRN_PCIE0_BASE #define PCIE1 DCRN_PCIE1_BASE #define PCIE2 DCRN_PCIE2_BASE @@ -47,6 +53,39 @@ #define PESDR0_PLLLCT2 0x03a1 #define PESDR0_PLLLCT3 0x03a2 +#if defined(CONFIG_440SPE) +#define PCIE0_SDR 0x300 +#define PCIE1_SDR 0x340 +#define PCIE2_SDR 0x370 +#endif + +#if defined(CONFIG_405EX) +#define PCIE0_SDR 0x400 +#define PCIE1_SDR 0x440 +#endif + +/* common regs, at least for 405EX and 440SPe */ +#define SDRN_PESDR_UTLSET1(n) (sdr_base(n) + 0x00) +#define SDRN_PESDR_UTLSET2(n) (sdr_base(n) + 0x01) +#define SDRN_PESDR_DLPSET(n) (sdr_base(n) + 0x02) +#define SDRN_PESDR_LOOP(n) (sdr_base(n) + 0x03) +#define SDRN_PESDR_RCSSET(n) (sdr_base(n) + 0x04) +#define SDRN_PESDR_RCSSTS(n) (sdr_base(n) + 0x05) + +#if defined(CONFIG_440SPE) +#define SDRN_PESDR_HSSL0SET1(n) (sdr_base(n) + 0x06) +#define SDRN_PESDR_HSSL0SET2(n) (sdr_base(n) + 0x07) +#define SDRN_PESDR_HSSL0STS(n) (sdr_base(n) + 0x08) +#define SDRN_PESDR_HSSL1SET1(n) (sdr_base(n) + 0x09) +#define SDRN_PESDR_HSSL1SET2(n) (sdr_base(n) + 0x0a) +#define SDRN_PESDR_HSSL1STS(n) (sdr_base(n) + 0x0b) +#define SDRN_PESDR_HSSL2SET1(n) (sdr_base(n) + 0x0c) +#define SDRN_PESDR_HSSL2SET2(n) (sdr_base(n) + 0x0d) +#define SDRN_PESDR_HSSL2STS(n) (sdr_base(n) + 0x0e) +#define SDRN_PESDR_HSSL3SET1(n) (sdr_base(n) + 0x0f) +#define SDRN_PESDR_HSSL3SET2(n) (sdr_base(n) + 0x10) +#define SDRN_PESDR_HSSL3STS(n) (sdr_base(n) + 0x11) + #define PESDR0_UTLSET1 0x0300 #define PESDR0_UTLSET2 0x0301 #define PESDR0_DLPSET 0x0302 @@ -123,6 +162,40 @@ #define PESDR2_HSSCTLSET 0x0382 #define PESDR2_LANE_ABCD 0x0383 +#elif defined(CONFIG_405EX) + +#define SDRN_PESDR_PHYSET1(n) (sdr_base(n) + 0x06) +#define SDRN_PESDR_PHYSET2(n) (sdr_base(n) + 0x07) +#define SDRN_PESDR_BIST(n) (sdr_base(n) + 0x08) +#define SDRN_PESDR_LPB(n) (sdr_base(n) + 0x0b) +#define SDRN_PESDR_PHYSTA(n) (sdr_base(n) + 0x0c) + +#define PESDR0_UTLSET1 0x0400 +#define PESDR0_UTLSET2 0x0401 +#define PESDR0_DLPSET 0x0402 +#define PESDR0_LOOP 0x0403 +#define PESDR0_RCSSET 0x0404 +#define PESDR0_RCSSTS 0x0405 +#define PESDR0_PHYSET1 0x0406 +#define PESDR0_PHYSET2 0x0407 +#define PESDR0_BIST 0x0408 +#define PESDR0_LPB 0x040B +#define PESDR0_PHYSTA 0x040C + +#define PESDR1_UTLSET1 0x0440 +#define PESDR1_UTLSET2 0x0441 +#define PESDR1_DLPSET 0x0442 +#define PESDR1_LOOP 0x0443 +#define PESDR1_RCSSET 0x0444 +#define PESDR1_RCSSTS 0x0445 +#define PESDR1_PHYSET1 0x0446 +#define PESDR1_PHYSET2 0x0447 +#define PESDR1_BIST 0x0448 +#define PESDR1_LPB 0x044B +#define PESDR1_PHYSTA 0x044C + +#endif + /* * UTL register offsets */ @@ -166,8 +239,32 @@ int ppc4xx_init_pcie(void); int ppc4xx_init_pcie_rootport(int port); +int ppc4xx_init_pcie_endport(int port); void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port); int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port); int pcie_hose_scan(struct pci_controller *hose, int bus); +static inline void mdelay(int n) +{ + u32 ms = n; + + while (ms--) + udelay(1000); +} + +static inline u32 sdr_base(int port) +{ + switch (port) { + default: /* to satisfy compiler */ + case 0: + return PCIE0_SDR; + case 1: + return PCIE1_SDR; +#if defined(PCIE2_SDR) + case 2: + return PCIE2_SDR; +#endif + } +} + #endif /* __4XX_PCIE_H */ -- cgit v1.3.1 From 3048bcbf0bad262378c5af68f2bf6778fb7d829a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 3 Oct 2007 15:01:02 +0200 Subject: ppc4xx: Rename 405gp_pci to 4xx_pci since its used on all 4xx platforms These files were introduced with the IBM 405GP but are currently used on all 4xx PPC platforms. So the name doesn't match the content anymore. This patch renames the files to 4xx_pci.c/h. Signed-off-by: Stefan Roese --- board/esd/ocrtc/cmd_ocrtc.c | 2 +- board/esd/pci405/cmd_pci405.c | 2 +- board/esd/pci405/pci405.c | 2 +- board/mpl/common/common_util.c | 4 +- board/mpl/common/flash.c | 2 +- common/usb.c | 2 +- cpu/ppc4xx/405gp_pci.c | 595 ----------------------------------------- cpu/ppc4xx/4xx_pci.c | 595 +++++++++++++++++++++++++++++++++++++++++ cpu/ppc4xx/Makefile | 6 +- include/405gp_pci.h | 52 ---- include/asm-ppc/4xx_pci.h | 52 ++++ 11 files changed, 657 insertions(+), 657 deletions(-) delete mode 100644 cpu/ppc4xx/405gp_pci.c create mode 100644 cpu/ppc4xx/4xx_pci.c delete mode 100644 include/405gp_pci.h create mode 100644 include/asm-ppc/4xx_pci.h (limited to 'include') diff --git a/board/esd/ocrtc/cmd_ocrtc.c b/board/esd/ocrtc/cmd_ocrtc.c index 4177f68ef4d..f83dfe870bc 100644 --- a/board/esd/ocrtc/cmd_ocrtc.c +++ b/board/esd/ocrtc/cmd_ocrtc.c @@ -25,7 +25,7 @@ #include #include #include -#include <405gp_pci.h> +#include #if defined(CONFIG_CMD_BSP) diff --git a/board/esd/pci405/cmd_pci405.c b/board/esd/pci405/cmd_pci405.c index 5b5ad8c4465..9a0bf1e3603 100644 --- a/board/esd/pci405/cmd_pci405.c +++ b/board/esd/pci405/cmd_pci405.c @@ -27,7 +27,7 @@ #include #include #include -#include <405gp_pci.h> +#include #include #include "pci405.h" diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c index e5d2273f07f..c4ab0720091 100644 --- a/board/esd/pci405/pci405.c +++ b/board/esd/pci405/pci405.c @@ -26,7 +26,7 @@ #include #include #include -#include <405gp_pci.h> +#include #include "pci405.h" diff --git a/board/mpl/common/common_util.c b/board/mpl/common/common_util.c index 278ad5c3488..f3aa0a73007 100644 --- a/board/mpl/common/common_util.c +++ b/board/mpl/common/common_util.c @@ -36,11 +36,11 @@ #ifdef CONFIG_PIP405 #include "../pip405/pip405.h" -#include <405gp_pci.h> +#include #endif #ifdef CONFIG_MIP405 #include "../mip405/mip405.h" -#include <405gp_pci.h> +#include #endif DECLARE_GLOBAL_DATA_PTR; diff --git a/board/mpl/common/flash.c b/board/mpl/common/flash.c index fd430083e2f..6f53192ac75 100644 --- a/board/mpl/common/flash.c +++ b/board/mpl/common/flash.c @@ -47,7 +47,7 @@ #if defined(CONFIG_PIP405) #include "../pip405/pip405.h" #endif -#include <405gp_pci.h> +#include #else /* defined(CONFIG_PATI) */ #include #endif diff --git a/common/usb.c b/common/usb.c index 933afa9e7bc..4df01eabe51 100644 --- a/common/usb.c +++ b/common/usb.c @@ -53,7 +53,7 @@ #include #ifdef CONFIG_4xx -#include <405gp_pci.h> +#include #endif #undef USB_DEBUG diff --git a/cpu/ppc4xx/405gp_pci.c b/cpu/ppc4xx/405gp_pci.c deleted file mode 100644 index 282e7a1ba47..00000000000 --- a/cpu/ppc4xx/405gp_pci.c +++ /dev/null @@ -1,595 +0,0 @@ -/*-----------------------------------------------------------------------------+ - * - * This source code has been made available to you by IBM on an AS-IS - * basis. Anyone receiving this source is licensed under IBM - * copyrights to use it in any way he or she deems fit, including - * copying it, modifying it, compiling it, and redistributing it either - * with or without modifications. No license under IBM patents or - * patent applications is to be implied by the copyright license. - * - * Any user of this software should understand that IBM cannot provide - * technical support for this software and will not be responsible for - * any consequences resulting from the use of this software. - * - * Any person who transfers this source code or any derivative work - * must include the IBM copyright notice, this paragraph, and the - * preceding two paragraphs in the transferred software. - * - * COPYRIGHT I B M CORPORATION 1995 - * LICENSED MATERIAL - PROGRAM PROPERTY OF I B M - *-----------------------------------------------------------------------------*/ -/*----------------------------------------------------------------------------+ - * - * File Name: 405gp_pci.c - * - * Function: Initialization code for the 405GP PCI Configuration regs. - * - * Author: Mark Game - * - * Change Activity- - * - * Date Description of Change BY - * --------- --------------------- --- - * 09-Sep-98 Created MCG - * 02-Nov-98 Removed External arbiter selected message JWB - * 27-Nov-98 Zero out PTMBAR2 and disable in PTM2MS JWB - * 04-Jan-99 Zero out other unused PMM and PTM regs. Change bus scan MCG - * from (0 to n) to (1 to n). - * 17-May-99 Port to Walnut JWB - * 17-Jun-99 Updated for VGA support JWB - * 21-Jun-99 Updated to allow SRAM region to be a target from PCI bus JWB - * 19-Jul-99 Updated for 405GP pass 1 errata #26 (Low PCI subsequent MCG - * target latency timer values are not supported). - * Should be fixed in pass 2. - * 09-Sep-99 Removed use of PTM2 since the SRAM region no longer needs JWB - * to be a PCI target. Zero out PTMBAR2 and disable in PTM2MS. - * 10-Dec-99 Updated PCI_Write_CFG_Reg for pass2 errata #6 JWB - * 11-Jan-00 Ensure PMMxMAs disabled before setting PMMxLAs. This is not - * really required after a reset since PMMxMAs are already - * disabled but is a good practice nonetheless. JWB - * 12-Jun-01 stefan.roese@esd-electronics.com - * - PCI host/adapter handling reworked - * 09-Jul-01 stefan.roese@esd-electronics.com - * - PCI host now configures from device 0 (not 1) to max_dev, - * (host configures itself) - * - On CPCI-405 pci base address and size is generated from - * SDRAM and FLASH size (CFG regs not used anymore) - * - Some minor changes for CPCI-405-A (adapter version) - * 14-Sep-01 stefan.roese@esd-electronics.com - * - CONFIG_PCI_SCAN_SHOW added to print pci devices upon startup - * 28-Sep-01 stefan.roese@esd-electronics.com - * - Changed pci master configuration for linux compatibility - * (no need for bios_fixup() anymore) - * 26-Feb-02 stefan.roese@esd-electronics.com - * - Bug fixed in pci configuration (Andrew May) - * - Removed pci class code init for CPCI405 board - * 15-May-02 stefan.roese@esd-electronics.com - * - New vga device handling - * 29-May-02 stefan.roese@esd-electronics.com - * - PCI class code init added (if defined) - *----------------------------------------------------------------------------*/ - -#include -#include -#if !defined(CONFIG_440) -#include <405gp_pci.h> -#endif -#include -#include - -#ifdef CONFIG_PCI - -DECLARE_GLOBAL_DATA_PTR; - -/* - * Board-specific pci initialization - * Platform code can reimplement pci_pre_init() if needed - */ -int __pci_pre_init(struct pci_controller *hose) -{ - return 1; -} -int pci_pre_init(struct pci_controller *hose) __attribute__((weak, alias("__pci_pre_init"))); - -#if defined(CONFIG_405GP) || defined(CONFIG_405EP) - -#if defined(CONFIG_PMC405) -ushort pmc405_pci_subsys_deviceid(void); -#endif - -/*#define DEBUG*/ - -/*-----------------------------------------------------------------------------+ - * pci_init. Initializes the 405GP PCI Configuration regs. - *-----------------------------------------------------------------------------*/ -void pci_405gp_init(struct pci_controller *hose) -{ - int i, reg_num = 0; - bd_t *bd = gd->bd; - - unsigned short temp_short; - unsigned long ptmpcila[2] = {CFG_PCI_PTM1PCI, CFG_PCI_PTM2PCI}; -#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405) - char *ptmla_str, *ptmms_str; -#endif - unsigned long ptmla[2] = {CFG_PCI_PTM1LA, CFG_PCI_PTM2LA}; - unsigned long ptmms[2] = {CFG_PCI_PTM1MS, CFG_PCI_PTM2MS}; -#if defined(CONFIG_PIP405) || defined (CONFIG_MIP405) - unsigned long pmmla[3] = {0x80000000, 0xA0000000, 0}; - unsigned long pmmma[3] = {0xE0000001, 0xE0000001, 0}; - unsigned long pmmpcila[3] = {0x80000000, 0x00000000, 0}; - unsigned long pmmpciha[3] = {0x00000000, 0x00000000, 0}; -#else - unsigned long pmmla[3] = {0x80000000, 0,0}; - unsigned long pmmma[3] = {0xC0000001, 0,0}; - unsigned long pmmpcila[3] = {0x80000000, 0,0}; - unsigned long pmmpciha[3] = {0x00000000, 0,0}; -#endif -#ifdef CONFIG_PCI_PNP -#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) - char *s; -#endif -#endif - -#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405) - ptmla_str = getenv("ptm1la"); - ptmms_str = getenv("ptm1ms"); - if(NULL != ptmla_str && NULL != ptmms_str ) { - ptmla[0] = simple_strtoul (ptmla_str, NULL, 16); - ptmms[0] = simple_strtoul (ptmms_str, NULL, 16); - } - - ptmla_str = getenv("ptm2la"); - ptmms_str = getenv("ptm2ms"); - if(NULL != ptmla_str && NULL != ptmms_str ) { - ptmla[1] = simple_strtoul (ptmla_str, NULL, 16); - ptmms[1] = simple_strtoul (ptmms_str, NULL, 16); - } -#endif - - /* - * Register the hose - */ - hose->first_busno = 0; - hose->last_busno = 0xff; - - /* ISA/PCI I/O space */ - pci_set_region(hose->regions + reg_num++, - MIN_PCI_PCI_IOADDR, - MIN_PLB_PCI_IOADDR, - 0x10000, - PCI_REGION_IO); - - /* PCI I/O space */ - pci_set_region(hose->regions + reg_num++, - 0x00800000, - 0xe8800000, - 0x03800000, - PCI_REGION_IO); - - reg_num = 2; - - /* Memory spaces */ - for (i=0; i<2; i++) - if (ptmms[i] & 1) - { - if (!i) hose->pci_fb = hose->regions + reg_num; - - pci_set_region(hose->regions + reg_num++, - ptmpcila[i], ptmla[i], - ~(ptmms[i] & 0xfffff000) + 1, - PCI_REGION_MEM | - PCI_REGION_MEMORY); - } - - /* PCI memory spaces */ - for (i=0; i<3; i++) - if (pmmma[i] & 1) - { - pci_set_region(hose->regions + reg_num++, - pmmpcila[i], pmmla[i], - ~(pmmma[i] & 0xfffff000) + 1, - PCI_REGION_MEM); - } - - hose->region_count = reg_num; - - pci_setup_indirect(hose, - PCICFGADR, - PCICFGDATA); - - if (hose->pci_fb) - pciauto_region_init(hose->pci_fb); - - /* Let board change/modify hose & do initial checks */ - if (pci_pre_init (hose) == 0) { - printf("PCI: Board-specific initialization failed.\n"); - printf("PCI: Configuration aborted.\n"); - return; - } - - pci_register_hose(hose); - - /*--------------------------------------------------------------------------+ - * 405GP PCI Master configuration. - * Map one 512 MB range of PLB/processor addresses to PCI memory space. - * PLB address 0x80000000-0xBFFFFFFF ==> PCI address 0x80000000-0xBFFFFFFF - * Use byte reversed out routines to handle endianess. - *--------------------------------------------------------------------------*/ - out32r(PMM0MA, (pmmma[0]&~0x1)); /* disable, configure PMMxLA, PMMxPCILA first */ - out32r(PMM0LA, pmmla[0]); - out32r(PMM0PCILA, pmmpcila[0]); - out32r(PMM0PCIHA, pmmpciha[0]); - out32r(PMM0MA, pmmma[0]); - - /*--------------------------------------------------------------------------+ - * PMM1 is not used. Initialize them to zero. - *--------------------------------------------------------------------------*/ - out32r(PMM1MA, (pmmma[1]&~0x1)); - out32r(PMM1LA, pmmla[1]); - out32r(PMM1PCILA, pmmpcila[1]); - out32r(PMM1PCIHA, pmmpciha[1]); - out32r(PMM1MA, pmmma[1]); - - /*--------------------------------------------------------------------------+ - * PMM2 is not used. Initialize them to zero. - *--------------------------------------------------------------------------*/ - out32r(PMM2MA, (pmmma[2]&~0x1)); - out32r(PMM2LA, pmmla[2]); - out32r(PMM2PCILA, pmmpcila[2]); - out32r(PMM2PCIHA, pmmpciha[2]); - out32r(PMM2MA, pmmma[2]); - - /*--------------------------------------------------------------------------+ - * 405GP PCI Target configuration. (PTM1) - * Note: PTM1MS is hardwire enabled but we set the enable bit anyway. - *--------------------------------------------------------------------------*/ - out32r(PTM1LA, ptmla[0]); /* insert address */ - out32r(PTM1MS, ptmms[0]); /* insert size, enable bit is 1 */ - pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_1, ptmpcila[0]); - - /*--------------------------------------------------------------------------+ - * 405GP PCI Target configuration. (PTM2) - *--------------------------------------------------------------------------*/ - out32r(PTM2LA, ptmla[1]); /* insert address */ - pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, ptmpcila[1]); - - if (ptmms[1] == 0) - { - out32r(PTM2MS, 0x00000001); /* set enable bit */ - pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, 0x00000000); - out32r(PTM2MS, 0x00000000); /* disable */ - } - else - { - out32r(PTM2MS, ptmms[1]); /* insert size, enable bit is 1 */ - } - - /* - * Insert Subsystem Vendor and Device ID - */ - pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_VENDOR_ID, CFG_PCI_SUBSYS_VENDORID); -#ifdef CONFIG_CPCI405 - if (mfdcr(strap) & PSR_PCI_ARBIT_EN) - pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID); - else - pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID2); -#else - pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID); -#endif - - /* - * Insert Class-code - */ -#ifdef CFG_PCI_CLASSCODE - pci_write_config_word(PCIDEVID_405GP, PCI_CLASS_SUB_CODE, CFG_PCI_CLASSCODE); -#endif /* CFG_PCI_CLASSCODE */ - - /*--------------------------------------------------------------------------+ - * If PCI speed = 66Mhz, set 66Mhz capable bit. - *--------------------------------------------------------------------------*/ - if (bd->bi_pci_busfreq >= 66000000) { - pci_read_config_word(PCIDEVID_405GP, PCI_STATUS, &temp_short); - pci_write_config_word(PCIDEVID_405GP,PCI_STATUS,(temp_short|PCI_STATUS_66MHZ)); - } - -#if (CONFIG_PCI_HOST != PCI_HOST_ADAPTER) -#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) - if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) || - (((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0))) -#endif - { - /*--------------------------------------------------------------------------+ - * Write the 405GP PCI Configuration regs. - * Enable 405GP to be a master on the PCI bus (PMM). - * Enable 405GP to act as a PCI memory target (PTM). - *--------------------------------------------------------------------------*/ - pci_read_config_word(PCIDEVID_405GP, PCI_COMMAND, &temp_short); - pci_write_config_word(PCIDEVID_405GP, PCI_COMMAND, temp_short | - PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); - } -#endif - -#if defined(CONFIG_405EP) /* on ppc405ep vendor id is not set */ - pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, 0x1014); /* IBM */ -#endif - - /* - * Set HCE bit (Host Configuration Enabled) - */ - pci_read_config_word(PCIDEVID_405GP, PCIBRDGOPT2, &temp_short); - pci_write_config_word(PCIDEVID_405GP, PCIBRDGOPT2, (temp_short | 0x0001)); - -#ifdef CONFIG_PCI_PNP - /*--------------------------------------------------------------------------+ - * Scan the PCI bus and configure devices found. - *--------------------------------------------------------------------------*/ -#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) - if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) || - (((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0))) -#endif - { -#ifdef CONFIG_PCI_SCAN_SHOW - printf("PCI: Bus Dev VenId DevId Class Int\n"); -#endif - hose->last_busno = pci_hose_scan(hose); - } -#endif /* CONFIG_PCI_PNP */ - -} - -/* - * drivers/pci.c skips every host bridge but the 405GP since it could - * be set as an Adapter. - * - * I (Andrew May) don't know what we should do here, but I don't want - * the auto setup of a PCI device disabling what is done pci_405gp_init - * as has happened before. - */ -void pci_405gp_setup_bridge(struct pci_controller *hose, pci_dev_t dev, - struct pci_config_table *entry) -{ -#ifdef DEBUG - printf("405gp_setup_bridge\n"); -#endif -} - -/* - * - */ - -void pci_405gp_fixup_irq(struct pci_controller *hose, pci_dev_t dev) -{ - unsigned char int_line = 0xff; - - /* - * Write pci interrupt line register (cpci405 specific) - */ - switch (PCI_DEV(dev) & 0x03) - { - case 0: - int_line = 27 + 2; - break; - case 1: - int_line = 27 + 3; - break; - case 2: - int_line = 27 + 0; - break; - case 3: - int_line = 27 + 1; - break; - } - - pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line); -} - -void pci_405gp_setup_vga(struct pci_controller *hose, pci_dev_t dev, - struct pci_config_table *entry) -{ - unsigned int cmdstat = 0; - - pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_prefetch, hose->pci_io); - - /* always enable io space on vga boards */ - pci_hose_read_config_dword(hose, dev, PCI_COMMAND, &cmdstat); - cmdstat |= PCI_COMMAND_IO; - pci_hose_write_config_dword(hose, dev, PCI_COMMAND, cmdstat); -} - -#if !(defined(CONFIG_PIP405) || defined (CONFIG_MIP405)) && !(defined (CONFIG_SC3)) - -/* - *As is these functs get called out of flash Not a horrible - *thing, but something to keep in mind. (no statics?) - */ -static struct pci_config_table pci_405gp_config_table[] = { -/*if VendID is 0 it terminates the table search (ie Walnut)*/ -#ifdef CFG_PCI_SUBSYS_VENDORID - {CFG_PCI_SUBSYS_VENDORID, PCI_ANY_ID, PCI_CLASS_BRIDGE_HOST, - PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_bridge}, -#endif - {PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA, - PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_vga}, - - {PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NOT_DEFINED_VGA, - PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_vga}, - - { } -}; - -static struct pci_controller hose = { - fixup_irq: pci_405gp_fixup_irq, - config_table: pci_405gp_config_table, -}; - -void pci_init_board(void) -{ - /*we want the ptrs to RAM not flash (ie don't use init list)*/ - hose.fixup_irq = pci_405gp_fixup_irq; - hose.config_table = pci_405gp_config_table; - pci_405gp_init(&hose); -} - -#endif - -#endif /* CONFIG_405GP */ - -/*-----------------------------------------------------------------------------+ - * CONFIG_440 - *-----------------------------------------------------------------------------*/ -#if defined(CONFIG_440) - -static struct pci_controller ppc440_hose = {0}; - - -int pci_440_init (struct pci_controller *hose) -{ - int reg_num = 0; - -#ifndef CONFIG_DISABLE_PISE_TEST - /*--------------------------------------------------------------------------+ - * The PCI initialization sequence enable bit must be set ... if not abort - * pci setup since updating the bit requires chip reset. - *--------------------------------------------------------------------------*/ -#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) - unsigned long strap; - - mfsdr(sdr_sdstp1,strap); - if ((strap & SDR0_SDSTP1_PISE_MASK) == 0) { - printf("PCI: SDR0_STRP1[PISE] not set.\n"); - printf("PCI: Configuration aborted.\n"); - return -1; - } -#elif defined(CONFIG_440GP) - unsigned long strap; - - strap = mfdcr(cpc0_strp1); - if ((strap & CPC0_STRP1_PISE_MASK) == 0) { - printf("PCI: CPC0_STRP1[PISE] not set.\n"); - printf("PCI: Configuration aborted.\n"); - return -1; - } -#endif -#endif /* CONFIG_DISABLE_PISE_TEST */ - - /*--------------------------------------------------------------------------+ - * PCI controller init - *--------------------------------------------------------------------------*/ - hose->first_busno = 0; - hose->last_busno = 0; - - /* PCI I/O space */ - pci_set_region(hose->regions + reg_num++, - 0x00000000, - PCIX0_IOBASE, - 0x10000, - PCI_REGION_IO); - - /* PCI memory space */ - pci_set_region(hose->regions + reg_num++, - CFG_PCI_TARGBASE, - CFG_PCI_MEMBASE, -#ifdef CFG_PCI_MEMSIZE - CFG_PCI_MEMSIZE, -#else - 0x10000000, -#endif - PCI_REGION_MEM ); - -#if defined(CONFIG_PCI_SYS_MEM_BUS) && defined(CONFIG_PCI_SYS_MEM_PHYS) && \ - defined(CONFIG_PCI_SYS_MEM_SIZE) - /* System memory space */ - pci_set_region(hose->regions + reg_num++, - CONFIG_PCI_SYS_MEM_BUS, - CONFIG_PCI_SYS_MEM_PHYS, - CONFIG_PCI_SYS_MEM_SIZE, - PCI_REGION_MEM | PCI_REGION_MEMORY ); -#endif - - hose->region_count = reg_num; - - pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA); - - /* Let board change/modify hose & do initial checks */ - if (pci_pre_init (hose) == 0) { - printf("PCI: Board-specific initialization failed.\n"); - printf("PCI: Configuration aborted.\n"); - return -1; - } - - pci_register_hose( hose ); - - /*--------------------------------------------------------------------------+ - * PCI target init - *--------------------------------------------------------------------------*/ -#if defined(CFG_PCI_TARGET_INIT) - pci_target_init(hose); /* Let board setup pci target */ -#else - out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID ); - out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_ID ); - out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */ -#endif - -#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) - out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */ - out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */ -#elif defined(PCIX0_BRDGOPT1) - out32r( PCIX0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */ - out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 1 ); /* Enable host config */ -#endif - - /*--------------------------------------------------------------------------+ - * PCI master init: default is one 256MB region for PCI memory: - * 0x3_00000000 - 0x3_0FFFFFFF ==> CFG_PCI_MEMBASE - *--------------------------------------------------------------------------*/ -#if defined(CFG_PCI_MASTER_INIT) - pci_master_init(hose); /* Let board setup pci master */ -#else - out32r( PCIX0_POM0SA, 0 ); /* disable */ - out32r( PCIX0_POM1SA, 0 ); /* disable */ - out32r( PCIX0_POM2SA, 0 ); /* disable */ -#if defined(CONFIG_440SPE) - out32r( PCIX0_POM0LAL, 0x10000000 ); - out32r( PCIX0_POM0LAH, 0x0000000c ); -#else - out32r( PCIX0_POM0LAL, 0x00000000 ); - out32r( PCIX0_POM0LAH, 0x00000003 ); -#endif - out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE ); - out32r( PCIX0_POM0PCIAH, 0x00000000 ); - out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */ - out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 ); -#endif - - /*--------------------------------------------------------------------------+ - * PCI host configuration -- we don't make any assumptions here ... the - * _board_must_indicate_ what to do -- there's just too many runtime - * scenarios in environments like cPCI, PPMC, etc. to make a determination - * based on hard-coded values or state of arbiter enable. - *--------------------------------------------------------------------------*/ - if (is_pci_host(hose)) { -#ifdef CONFIG_PCI_SCAN_SHOW - printf("PCI: Bus Dev VenId DevId Class Int\n"); -#endif -#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \ - !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) - out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER); -#endif - hose->last_busno = pci_hose_scan(hose); - } - return hose->last_busno; -} - -void pci_init_board(void) -{ - int busno; - - busno = pci_440_init (&ppc440_hose); -#if defined(CONFIG_440SPE) - pcie_setup_hoses(busno + 1); -#endif -} - -#endif /* CONFIG_440 */ -#endif /* CONFIG_PCI */ diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c new file mode 100644 index 00000000000..e6170517ae6 --- /dev/null +++ b/cpu/ppc4xx/4xx_pci.c @@ -0,0 +1,595 @@ +/*-----------------------------------------------------------------------------+ + * + * This source code has been made available to you by IBM on an AS-IS + * basis. Anyone receiving this source is licensed under IBM + * copyrights to use it in any way he or she deems fit, including + * copying it, modifying it, compiling it, and redistributing it either + * with or without modifications. No license under IBM patents or + * patent applications is to be implied by the copyright license. + * + * Any user of this software should understand that IBM cannot provide + * technical support for this software and will not be responsible for + * any consequences resulting from the use of this software. + * + * Any person who transfers this source code or any derivative work + * must include the IBM copyright notice, this paragraph, and the + * preceding two paragraphs in the transferred software. + * + * COPYRIGHT I B M CORPORATION 1995 + * LICENSED MATERIAL - PROGRAM PROPERTY OF I B M + *-----------------------------------------------------------------------------*/ +/*----------------------------------------------------------------------------+ + * + * File Name: 405gp_pci.c + * + * Function: Initialization code for the 405GP PCI Configuration regs. + * + * Author: Mark Game + * + * Change Activity- + * + * Date Description of Change BY + * --------- --------------------- --- + * 09-Sep-98 Created MCG + * 02-Nov-98 Removed External arbiter selected message JWB + * 27-Nov-98 Zero out PTMBAR2 and disable in PTM2MS JWB + * 04-Jan-99 Zero out other unused PMM and PTM regs. Change bus scan MCG + * from (0 to n) to (1 to n). + * 17-May-99 Port to Walnut JWB + * 17-Jun-99 Updated for VGA support JWB + * 21-Jun-99 Updated to allow SRAM region to be a target from PCI bus JWB + * 19-Jul-99 Updated for 405GP pass 1 errata #26 (Low PCI subsequent MCG + * target latency timer values are not supported). + * Should be fixed in pass 2. + * 09-Sep-99 Removed use of PTM2 since the SRAM region no longer needs JWB + * to be a PCI target. Zero out PTMBAR2 and disable in PTM2MS. + * 10-Dec-99 Updated PCI_Write_CFG_Reg for pass2 errata #6 JWB + * 11-Jan-00 Ensure PMMxMAs disabled before setting PMMxLAs. This is not + * really required after a reset since PMMxMAs are already + * disabled but is a good practice nonetheless. JWB + * 12-Jun-01 stefan.roese@esd-electronics.com + * - PCI host/adapter handling reworked + * 09-Jul-01 stefan.roese@esd-electronics.com + * - PCI host now configures from device 0 (not 1) to max_dev, + * (host configures itself) + * - On CPCI-405 pci base address and size is generated from + * SDRAM and FLASH size (CFG regs not used anymore) + * - Some minor changes for CPCI-405-A (adapter version) + * 14-Sep-01 stefan.roese@esd-electronics.com + * - CONFIG_PCI_SCAN_SHOW added to print pci devices upon startup + * 28-Sep-01 stefan.roese@esd-electronics.com + * - Changed pci master configuration for linux compatibility + * (no need for bios_fixup() anymore) + * 26-Feb-02 stefan.roese@esd-electronics.com + * - Bug fixed in pci configuration (Andrew May) + * - Removed pci class code init for CPCI405 board + * 15-May-02 stefan.roese@esd-electronics.com + * - New vga device handling + * 29-May-02 stefan.roese@esd-electronics.com + * - PCI class code init added (if defined) + *----------------------------------------------------------------------------*/ + +#include +#include +#if !defined(CONFIG_440) +#include +#endif +#include +#include + +#ifdef CONFIG_PCI + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Board-specific pci initialization + * Platform code can reimplement pci_pre_init() if needed + */ +int __pci_pre_init(struct pci_controller *hose) +{ + return 1; +} +int pci_pre_init(struct pci_controller *hose) __attribute__((weak, alias("__pci_pre_init"))); + +#if defined(CONFIG_405GP) || defined(CONFIG_405EP) + +#if defined(CONFIG_PMC405) +ushort pmc405_pci_subsys_deviceid(void); +#endif + +/*#define DEBUG*/ + +/*-----------------------------------------------------------------------------+ + * pci_init. Initializes the 405GP PCI Configuration regs. + *-----------------------------------------------------------------------------*/ +void pci_405gp_init(struct pci_controller *hose) +{ + int i, reg_num = 0; + bd_t *bd = gd->bd; + + unsigned short temp_short; + unsigned long ptmpcila[2] = {CFG_PCI_PTM1PCI, CFG_PCI_PTM2PCI}; +#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405) + char *ptmla_str, *ptmms_str; +#endif + unsigned long ptmla[2] = {CFG_PCI_PTM1LA, CFG_PCI_PTM2LA}; + unsigned long ptmms[2] = {CFG_PCI_PTM1MS, CFG_PCI_PTM2MS}; +#if defined(CONFIG_PIP405) || defined (CONFIG_MIP405) + unsigned long pmmla[3] = {0x80000000, 0xA0000000, 0}; + unsigned long pmmma[3] = {0xE0000001, 0xE0000001, 0}; + unsigned long pmmpcila[3] = {0x80000000, 0x00000000, 0}; + unsigned long pmmpciha[3] = {0x00000000, 0x00000000, 0}; +#else + unsigned long pmmla[3] = {0x80000000, 0,0}; + unsigned long pmmma[3] = {0xC0000001, 0,0}; + unsigned long pmmpcila[3] = {0x80000000, 0,0}; + unsigned long pmmpciha[3] = {0x00000000, 0,0}; +#endif +#ifdef CONFIG_PCI_PNP +#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) + char *s; +#endif +#endif + +#if defined(CONFIG_CPCI405) || defined(CONFIG_PMC405) + ptmla_str = getenv("ptm1la"); + ptmms_str = getenv("ptm1ms"); + if(NULL != ptmla_str && NULL != ptmms_str ) { + ptmla[0] = simple_strtoul (ptmla_str, NULL, 16); + ptmms[0] = simple_strtoul (ptmms_str, NULL, 16); + } + + ptmla_str = getenv("ptm2la"); + ptmms_str = getenv("ptm2ms"); + if(NULL != ptmla_str && NULL != ptmms_str ) { + ptmla[1] = simple_strtoul (ptmla_str, NULL, 16); + ptmms[1] = simple_strtoul (ptmms_str, NULL, 16); + } +#endif + + /* + * Register the hose + */ + hose->first_busno = 0; + hose->last_busno = 0xff; + + /* ISA/PCI I/O space */ + pci_set_region(hose->regions + reg_num++, + MIN_PCI_PCI_IOADDR, + MIN_PLB_PCI_IOADDR, + 0x10000, + PCI_REGION_IO); + + /* PCI I/O space */ + pci_set_region(hose->regions + reg_num++, + 0x00800000, + 0xe8800000, + 0x03800000, + PCI_REGION_IO); + + reg_num = 2; + + /* Memory spaces */ + for (i=0; i<2; i++) + if (ptmms[i] & 1) + { + if (!i) hose->pci_fb = hose->regions + reg_num; + + pci_set_region(hose->regions + reg_num++, + ptmpcila[i], ptmla[i], + ~(ptmms[i] & 0xfffff000) + 1, + PCI_REGION_MEM | + PCI_REGION_MEMORY); + } + + /* PCI memory spaces */ + for (i=0; i<3; i++) + if (pmmma[i] & 1) + { + pci_set_region(hose->regions + reg_num++, + pmmpcila[i], pmmla[i], + ~(pmmma[i] & 0xfffff000) + 1, + PCI_REGION_MEM); + } + + hose->region_count = reg_num; + + pci_setup_indirect(hose, + PCICFGADR, + PCICFGDATA); + + if (hose->pci_fb) + pciauto_region_init(hose->pci_fb); + + /* Let board change/modify hose & do initial checks */ + if (pci_pre_init (hose) == 0) { + printf("PCI: Board-specific initialization failed.\n"); + printf("PCI: Configuration aborted.\n"); + return; + } + + pci_register_hose(hose); + + /*--------------------------------------------------------------------------+ + * 405GP PCI Master configuration. + * Map one 512 MB range of PLB/processor addresses to PCI memory space. + * PLB address 0x80000000-0xBFFFFFFF ==> PCI address 0x80000000-0xBFFFFFFF + * Use byte reversed out routines to handle endianess. + *--------------------------------------------------------------------------*/ + out32r(PMM0MA, (pmmma[0]&~0x1)); /* disable, configure PMMxLA, PMMxPCILA first */ + out32r(PMM0LA, pmmla[0]); + out32r(PMM0PCILA, pmmpcila[0]); + out32r(PMM0PCIHA, pmmpciha[0]); + out32r(PMM0MA, pmmma[0]); + + /*--------------------------------------------------------------------------+ + * PMM1 is not used. Initialize them to zero. + *--------------------------------------------------------------------------*/ + out32r(PMM1MA, (pmmma[1]&~0x1)); + out32r(PMM1LA, pmmla[1]); + out32r(PMM1PCILA, pmmpcila[1]); + out32r(PMM1PCIHA, pmmpciha[1]); + out32r(PMM1MA, pmmma[1]); + + /*--------------------------------------------------------------------------+ + * PMM2 is not used. Initialize them to zero. + *--------------------------------------------------------------------------*/ + out32r(PMM2MA, (pmmma[2]&~0x1)); + out32r(PMM2LA, pmmla[2]); + out32r(PMM2PCILA, pmmpcila[2]); + out32r(PMM2PCIHA, pmmpciha[2]); + out32r(PMM2MA, pmmma[2]); + + /*--------------------------------------------------------------------------+ + * 405GP PCI Target configuration. (PTM1) + * Note: PTM1MS is hardwire enabled but we set the enable bit anyway. + *--------------------------------------------------------------------------*/ + out32r(PTM1LA, ptmla[0]); /* insert address */ + out32r(PTM1MS, ptmms[0]); /* insert size, enable bit is 1 */ + pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_1, ptmpcila[0]); + + /*--------------------------------------------------------------------------+ + * 405GP PCI Target configuration. (PTM2) + *--------------------------------------------------------------------------*/ + out32r(PTM2LA, ptmla[1]); /* insert address */ + pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, ptmpcila[1]); + + if (ptmms[1] == 0) + { + out32r(PTM2MS, 0x00000001); /* set enable bit */ + pci_write_config_dword(PCIDEVID_405GP, PCI_BASE_ADDRESS_2, 0x00000000); + out32r(PTM2MS, 0x00000000); /* disable */ + } + else + { + out32r(PTM2MS, ptmms[1]); /* insert size, enable bit is 1 */ + } + + /* + * Insert Subsystem Vendor and Device ID + */ + pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_VENDOR_ID, CFG_PCI_SUBSYS_VENDORID); +#ifdef CONFIG_CPCI405 + if (mfdcr(strap) & PSR_PCI_ARBIT_EN) + pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID); + else + pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID2); +#else + pci_write_config_word(PCIDEVID_405GP, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_DEVICEID); +#endif + + /* + * Insert Class-code + */ +#ifdef CFG_PCI_CLASSCODE + pci_write_config_word(PCIDEVID_405GP, PCI_CLASS_SUB_CODE, CFG_PCI_CLASSCODE); +#endif /* CFG_PCI_CLASSCODE */ + + /*--------------------------------------------------------------------------+ + * If PCI speed = 66Mhz, set 66Mhz capable bit. + *--------------------------------------------------------------------------*/ + if (bd->bi_pci_busfreq >= 66000000) { + pci_read_config_word(PCIDEVID_405GP, PCI_STATUS, &temp_short); + pci_write_config_word(PCIDEVID_405GP,PCI_STATUS,(temp_short|PCI_STATUS_66MHZ)); + } + +#if (CONFIG_PCI_HOST != PCI_HOST_ADAPTER) +#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) + if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) || + (((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0))) +#endif + { + /*--------------------------------------------------------------------------+ + * Write the 405GP PCI Configuration regs. + * Enable 405GP to be a master on the PCI bus (PMM). + * Enable 405GP to act as a PCI memory target (PTM). + *--------------------------------------------------------------------------*/ + pci_read_config_word(PCIDEVID_405GP, PCI_COMMAND, &temp_short); + pci_write_config_word(PCIDEVID_405GP, PCI_COMMAND, temp_short | + PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); + } +#endif + +#if defined(CONFIG_405EP) /* on ppc405ep vendor id is not set */ + pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, 0x1014); /* IBM */ +#endif + + /* + * Set HCE bit (Host Configuration Enabled) + */ + pci_read_config_word(PCIDEVID_405GP, PCIBRDGOPT2, &temp_short); + pci_write_config_word(PCIDEVID_405GP, PCIBRDGOPT2, (temp_short | 0x0001)); + +#ifdef CONFIG_PCI_PNP + /*--------------------------------------------------------------------------+ + * Scan the PCI bus and configure devices found. + *--------------------------------------------------------------------------*/ +#if (CONFIG_PCI_HOST == PCI_HOST_AUTO) + if ((mfdcr(strap) & PSR_PCI_ARBIT_EN) || + (((s = getenv("pciscan")) != NULL) && (strcmp(s, "yes") == 0))) +#endif + { +#ifdef CONFIG_PCI_SCAN_SHOW + printf("PCI: Bus Dev VenId DevId Class Int\n"); +#endif + hose->last_busno = pci_hose_scan(hose); + } +#endif /* CONFIG_PCI_PNP */ + +} + +/* + * drivers/pci.c skips every host bridge but the 405GP since it could + * be set as an Adapter. + * + * I (Andrew May) don't know what we should do here, but I don't want + * the auto setup of a PCI device disabling what is done pci_405gp_init + * as has happened before. + */ +void pci_405gp_setup_bridge(struct pci_controller *hose, pci_dev_t dev, + struct pci_config_table *entry) +{ +#ifdef DEBUG + printf("405gp_setup_bridge\n"); +#endif +} + +/* + * + */ + +void pci_405gp_fixup_irq(struct pci_controller *hose, pci_dev_t dev) +{ + unsigned char int_line = 0xff; + + /* + * Write pci interrupt line register (cpci405 specific) + */ + switch (PCI_DEV(dev) & 0x03) + { + case 0: + int_line = 27 + 2; + break; + case 1: + int_line = 27 + 3; + break; + case 2: + int_line = 27 + 0; + break; + case 3: + int_line = 27 + 1; + break; + } + + pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, int_line); +} + +void pci_405gp_setup_vga(struct pci_controller *hose, pci_dev_t dev, + struct pci_config_table *entry) +{ + unsigned int cmdstat = 0; + + pciauto_setup_device(hose, dev, 6, hose->pci_mem, hose->pci_prefetch, hose->pci_io); + + /* always enable io space on vga boards */ + pci_hose_read_config_dword(hose, dev, PCI_COMMAND, &cmdstat); + cmdstat |= PCI_COMMAND_IO; + pci_hose_write_config_dword(hose, dev, PCI_COMMAND, cmdstat); +} + +#if !(defined(CONFIG_PIP405) || defined (CONFIG_MIP405)) && !(defined (CONFIG_SC3)) + +/* + *As is these functs get called out of flash Not a horrible + *thing, but something to keep in mind. (no statics?) + */ +static struct pci_config_table pci_405gp_config_table[] = { +/*if VendID is 0 it terminates the table search (ie Walnut)*/ +#ifdef CFG_PCI_SUBSYS_VENDORID + {CFG_PCI_SUBSYS_VENDORID, PCI_ANY_ID, PCI_CLASS_BRIDGE_HOST, + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_bridge}, +#endif + {PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA, + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_vga}, + + {PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_NOT_DEFINED_VGA, + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, pci_405gp_setup_vga}, + + { } +}; + +static struct pci_controller hose = { + fixup_irq: pci_405gp_fixup_irq, + config_table: pci_405gp_config_table, +}; + +void pci_init_board(void) +{ + /*we want the ptrs to RAM not flash (ie don't use init list)*/ + hose.fixup_irq = pci_405gp_fixup_irq; + hose.config_table = pci_405gp_config_table; + pci_405gp_init(&hose); +} + +#endif + +#endif /* CONFIG_405GP */ + +/*-----------------------------------------------------------------------------+ + * CONFIG_440 + *-----------------------------------------------------------------------------*/ +#if defined(CONFIG_440) + +static struct pci_controller ppc440_hose = {0}; + + +int pci_440_init (struct pci_controller *hose) +{ + int reg_num = 0; + +#ifndef CONFIG_DISABLE_PISE_TEST + /*--------------------------------------------------------------------------+ + * The PCI initialization sequence enable bit must be set ... if not abort + * pci setup since updating the bit requires chip reset. + *--------------------------------------------------------------------------*/ +#if defined(CONFIG_440GX) || defined(CONFIG_440SP) || defined(CONFIG_440SPE) + unsigned long strap; + + mfsdr(sdr_sdstp1,strap); + if ((strap & SDR0_SDSTP1_PISE_MASK) == 0) { + printf("PCI: SDR0_STRP1[PISE] not set.\n"); + printf("PCI: Configuration aborted.\n"); + return -1; + } +#elif defined(CONFIG_440GP) + unsigned long strap; + + strap = mfdcr(cpc0_strp1); + if ((strap & CPC0_STRP1_PISE_MASK) == 0) { + printf("PCI: CPC0_STRP1[PISE] not set.\n"); + printf("PCI: Configuration aborted.\n"); + return -1; + } +#endif +#endif /* CONFIG_DISABLE_PISE_TEST */ + + /*--------------------------------------------------------------------------+ + * PCI controller init + *--------------------------------------------------------------------------*/ + hose->first_busno = 0; + hose->last_busno = 0; + + /* PCI I/O space */ + pci_set_region(hose->regions + reg_num++, + 0x00000000, + PCIX0_IOBASE, + 0x10000, + PCI_REGION_IO); + + /* PCI memory space */ + pci_set_region(hose->regions + reg_num++, + CFG_PCI_TARGBASE, + CFG_PCI_MEMBASE, +#ifdef CFG_PCI_MEMSIZE + CFG_PCI_MEMSIZE, +#else + 0x10000000, +#endif + PCI_REGION_MEM ); + +#if defined(CONFIG_PCI_SYS_MEM_BUS) && defined(CONFIG_PCI_SYS_MEM_PHYS) && \ + defined(CONFIG_PCI_SYS_MEM_SIZE) + /* System memory space */ + pci_set_region(hose->regions + reg_num++, + CONFIG_PCI_SYS_MEM_BUS, + CONFIG_PCI_SYS_MEM_PHYS, + CONFIG_PCI_SYS_MEM_SIZE, + PCI_REGION_MEM | PCI_REGION_MEMORY ); +#endif + + hose->region_count = reg_num; + + pci_setup_indirect(hose, PCIX0_CFGADR, PCIX0_CFGDATA); + + /* Let board change/modify hose & do initial checks */ + if (pci_pre_init (hose) == 0) { + printf("PCI: Board-specific initialization failed.\n"); + printf("PCI: Configuration aborted.\n"); + return -1; + } + + pci_register_hose( hose ); + + /*--------------------------------------------------------------------------+ + * PCI target init + *--------------------------------------------------------------------------*/ +#if defined(CFG_PCI_TARGET_INIT) + pci_target_init(hose); /* Let board setup pci target */ +#else + out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID ); + out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_ID ); + out16r( PCIX0_CLS, 0x00060000 ); /* Bridge, host bridge */ +#endif + +#if defined(CONFIG_440GX) || defined(CONFIG_440SPE) + out32r( PCIX0_BRDGOPT1, 0x04000060 ); /* PLB Rq pri highest */ + out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 0x83 ); /* Enable host config, clear Timeout, ensure int src1 */ +#elif defined(PCIX0_BRDGOPT1) + out32r( PCIX0_BRDGOPT1, 0x10000060 ); /* PLB Rq pri highest */ + out32r( PCIX0_BRDGOPT2, in32(PCIX0_BRDGOPT2) | 1 ); /* Enable host config */ +#endif + + /*--------------------------------------------------------------------------+ + * PCI master init: default is one 256MB region for PCI memory: + * 0x3_00000000 - 0x3_0FFFFFFF ==> CFG_PCI_MEMBASE + *--------------------------------------------------------------------------*/ +#if defined(CFG_PCI_MASTER_INIT) + pci_master_init(hose); /* Let board setup pci master */ +#else + out32r( PCIX0_POM0SA, 0 ); /* disable */ + out32r( PCIX0_POM1SA, 0 ); /* disable */ + out32r( PCIX0_POM2SA, 0 ); /* disable */ +#if defined(CONFIG_440SPE) + out32r( PCIX0_POM0LAL, 0x10000000 ); + out32r( PCIX0_POM0LAH, 0x0000000c ); +#else + out32r( PCIX0_POM0LAL, 0x00000000 ); + out32r( PCIX0_POM0LAH, 0x00000003 ); +#endif + out32r( PCIX0_POM0PCIAL, CFG_PCI_MEMBASE ); + out32r( PCIX0_POM0PCIAH, 0x00000000 ); + out32r( PCIX0_POM0SA, 0xf0000001 ); /* 256MB, enabled */ + out32r( PCIX0_STS, in32r( PCIX0_STS ) & ~0x0000fff8 ); +#endif + + /*--------------------------------------------------------------------------+ + * PCI host configuration -- we don't make any assumptions here ... the + * _board_must_indicate_ what to do -- there's just too many runtime + * scenarios in environments like cPCI, PPMC, etc. to make a determination + * based on hard-coded values or state of arbiter enable. + *--------------------------------------------------------------------------*/ + if (is_pci_host(hose)) { +#ifdef CONFIG_PCI_SCAN_SHOW + printf("PCI: Bus Dev VenId DevId Class Int\n"); +#endif +#if !defined(CONFIG_440EP) && !defined(CONFIG_440GR) && \ + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) + out16r( PCIX0_CMD, in16r( PCIX0_CMD ) | PCI_COMMAND_MASTER); +#endif + hose->last_busno = pci_hose_scan(hose); + } + return hose->last_busno; +} + +void pci_init_board(void) +{ + int busno; + + busno = pci_440_init (&ppc440_hose); +#if defined(CONFIG_440SPE) + pcie_setup_hoses(busno + 1); +#endif +} + +#endif /* CONFIG_440 */ +#endif /* CONFIG_PCI */ diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index 28a8e2bcb7e..a11faec14e1 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -27,11 +27,11 @@ LIB = $(obj)lib$(CPU).a START = start.o resetvec.o kgdb.o SOBJS = dcr.o -COBJS = 405gp_pci.o 4xx_pcie.o 4xx_enet.o \ +COBJS = 40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o \ + 4xx_pci.o 4xx_pcie.o 4xx_enet.o \ bedbug_405.o commproc.o \ cpu.o cpu_init.o gpio.o i2c.o interrupts.o \ - miiphy.o ndfc.o sdram.o serial.o \ - 40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o speed.o \ + miiphy.o ndfc.o sdram.o serial.o speed.o \ tlb.o traps.o usb_ohci.o usb.o usbdev.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) diff --git a/include/405gp_pci.h b/include/405gp_pci.h deleted file mode 100644 index 3c1adec19c5..00000000000 --- a/include/405gp_pci.h +++ /dev/null @@ -1,52 +0,0 @@ -#ifndef _405GP_PCI_H -#define _405GP_PCI_H - -/*----------------------------------------------------------------------------+ -| 405GP PCI core memory map defines. -+----------------------------------------------------------------------------*/ -#define MIN_PCI_MEMADDR1 0x80000000 -#define MIN_PCI_MEMADDR2 0x00000000 -#define MIN_PLB_PCI_IOADDR 0xE8000000 /* PLB side of PCI I/O address space */ -#define MIN_PCI_PCI_IOADDR 0x00000000 /* PCI side of PCI I/O address space */ -#define MAX_PCI_DEVICES 32 - -/*----------------------------------------------------------------------------+ -| Defines for the 405GP PCI Config address and data registers followed by -| defines for the standard PCI device configuration header. -+----------------------------------------------------------------------------*/ -#define PCICFGADR 0xEEC00000 -#define PCICFGDATA 0xEEC00004 - -#define PCIBUSNUM 0x40 /* 405GP specific parameters */ -#define PCISUBBUSNUM 0x41 -#define PCIDISCOUNT 0x42 -#define PCIBRDGOPT1 0x4A -#define PCIBRDGOPT2 0x60 - -/*----------------------------------------------------------------------------+ -| Defines for 405GP PCI Master local configuration regs. -+----------------------------------------------------------------------------*/ -#define PMM0LA 0xEF400000 -#define PMM0MA 0xEF400004 -#define PMM0PCILA 0xEF400008 -#define PMM0PCIHA 0xEF40000C -#define PMM1LA 0xEF400010 -#define PMM1MA 0xEF400014 -#define PMM1PCILA 0xEF400018 -#define PMM1PCIHA 0xEF40001C -#define PMM2LA 0xEF400020 -#define PMM2MA 0xEF400024 -#define PMM2PCILA 0xEF400028 -#define PMM2PCIHA 0xEF40002C - -/*----------------------------------------------------------------------------+ -| Defines for 405GP PCI Target local configuration regs. -+----------------------------------------------------------------------------*/ -#define PTM1MS 0xEF400030 -#define PTM1LA 0xEF400034 -#define PTM2MS 0xEF400038 -#define PTM2LA 0xEF40003C - -#define PCIDEVID_405GP 0x0 - -#endif diff --git a/include/asm-ppc/4xx_pci.h b/include/asm-ppc/4xx_pci.h new file mode 100644 index 00000000000..3c1adec19c5 --- /dev/null +++ b/include/asm-ppc/4xx_pci.h @@ -0,0 +1,52 @@ +#ifndef _405GP_PCI_H +#define _405GP_PCI_H + +/*----------------------------------------------------------------------------+ +| 405GP PCI core memory map defines. ++----------------------------------------------------------------------------*/ +#define MIN_PCI_MEMADDR1 0x80000000 +#define MIN_PCI_MEMADDR2 0x00000000 +#define MIN_PLB_PCI_IOADDR 0xE8000000 /* PLB side of PCI I/O address space */ +#define MIN_PCI_PCI_IOADDR 0x00000000 /* PCI side of PCI I/O address space */ +#define MAX_PCI_DEVICES 32 + +/*----------------------------------------------------------------------------+ +| Defines for the 405GP PCI Config address and data registers followed by +| defines for the standard PCI device configuration header. ++----------------------------------------------------------------------------*/ +#define PCICFGADR 0xEEC00000 +#define PCICFGDATA 0xEEC00004 + +#define PCIBUSNUM 0x40 /* 405GP specific parameters */ +#define PCISUBBUSNUM 0x41 +#define PCIDISCOUNT 0x42 +#define PCIBRDGOPT1 0x4A +#define PCIBRDGOPT2 0x60 + +/*----------------------------------------------------------------------------+ +| Defines for 405GP PCI Master local configuration regs. ++----------------------------------------------------------------------------*/ +#define PMM0LA 0xEF400000 +#define PMM0MA 0xEF400004 +#define PMM0PCILA 0xEF400008 +#define PMM0PCIHA 0xEF40000C +#define PMM1LA 0xEF400010 +#define PMM1MA 0xEF400014 +#define PMM1PCILA 0xEF400018 +#define PMM1PCIHA 0xEF40001C +#define PMM2LA 0xEF400020 +#define PMM2MA 0xEF400024 +#define PMM2PCILA 0xEF400028 +#define PMM2PCIHA 0xEF40002C + +/*----------------------------------------------------------------------------+ +| Defines for 405GP PCI Target local configuration regs. ++----------------------------------------------------------------------------*/ +#define PTM1MS 0xEF400030 +#define PTM1LA 0xEF400034 +#define PTM2MS 0xEF400038 +#define PTM2LA 0xEF40003C + +#define PCIDEVID_405GP 0x0 + +#endif -- cgit v1.3.1 From 4dbee8a90df613eb517aadbecebd70f168913d30 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 07:57:20 +0200 Subject: ppc4xx: 4xx_pcie: Change CFG_PCIE_MEMSIZE to 128MB on Yucca & Katmai 128MB seems to be the smallest possible value for the memory size for on PCIe port. With this change now the BAR's of the PCIe cards are accessible under U-Boot. One big note: This only works for PCIe port 0 & 1. For port 2 this currently doesn't work, since the base address is now 0xc0000000 (0xb0000000 + 2 * 0x08000000), and this is already occupied by CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean to change the base addresses completely and this change would have too much impact right now. This patch adds debug output to the 4xx pcie driver too. Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_pcie.c | 25 ++++++++++++++++++++++++- include/configs/katmai.h | 2 +- include/configs/yucca.h | 2 +- 3 files changed, 26 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index 2b3e657806a..7ac8ce0d765 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -20,6 +20,11 @@ * */ +/* define DEBUG for debugging output (obviously ;-)) */ +#if 1 +#define DEBUG +#endif + #include #include #include @@ -708,7 +713,10 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) * subregions and to enable the outbound translation. */ out_le32(mbase + PECFG_POM0LAH, 0x00000000); - out_le32(mbase + PECFG_POM0LAL, 0x00000000); + out_le32(mbase + PECFG_POM0LAL, CFG_PCIE_MEMBASE + + port * CFG_PCIE_MEMSIZE); + debug("PECFG_POM0LA=%08x.%08x\n", in_le32(mbase + PECFG_POM0LAH), + in_le32(mbase + PECFG_POM0LAL)); switch (port) { case 0: @@ -718,6 +726,11 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), ~(CFG_PCIE_MEMSIZE - 1) | 3); + debug("0:PEGPL_OMR1BA=%08x.%08x MSK=%08x.%08x\n", + mfdcr(DCRN_PEGPL_OMR1BAH(PCIE0)), + mfdcr(DCRN_PEGPL_OMR1BAL(PCIE0)), + mfdcr(DCRN_PEGPL_OMR1MSKH(PCIE0)), + mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE0))); break; case 1: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); @@ -726,6 +739,11 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), ~(CFG_PCIE_MEMSIZE - 1) | 3); + debug("1:PEGPL_OMR1BA=%08x.%08x MSK=%08x.%08x\n", + mfdcr(DCRN_PEGPL_OMR1BAH(PCIE1)), + mfdcr(DCRN_PEGPL_OMR1BAL(PCIE1)), + mfdcr(DCRN_PEGPL_OMR1MSKH(PCIE1)), + mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE1))); break; case 2: mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); @@ -734,6 +752,11 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), ~(CFG_PCIE_MEMSIZE - 1) | 3); + debug("2:PEGPL_OMR1BA=%08x.%08x MSK=%08x.%08x\n", + mfdcr(DCRN_PEGPL_OMR1BAH(PCIE2)), + mfdcr(DCRN_PEGPL_OMR1BAL(PCIE2)), + mfdcr(DCRN_PEGPL_OMR1MSKH(PCIE2)), + mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE2))); break; } diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 7908e5a4743..03c3cb3bdf0 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -62,7 +62,7 @@ #define CFG_PCI_TARGBASE CFG_PCI_MEMBASE #define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x01000000 +#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ #define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ #define CFG_PCIE0_CFGBASE 0xc0000000 diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 74033b4aef4..6caf21bcb51 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -64,7 +64,7 @@ #define CFG_PCI_TARGBASE CFG_PCI_MEMBASE #define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x01000000 +#define CFG_PCIE_MEMSIZE 0x08000000 /* smallest incr for PCIe port */ #define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ #define CFG_PCIE0_CFGBASE 0xc0000000 -- cgit v1.3.1 From 97923770cb52b64d69eec958a11b2eda8d46e0f7 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 09:18:23 +0200 Subject: ppc4xx: 4xx_pcie: More general cleanup and 405EX PCIe support added Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_pcie.c | 93 +++++++++++++++++++++++++++------------------- include/asm-ppc/4xx_pcie.h | 31 ++++++++++------ include/configs/katmai.h | 3 ++ include/configs/yucca.h | 3 ++ 4 files changed, 79 insertions(+), 51 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index 7ac8ce0d765..d1ba8905312 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -31,7 +31,8 @@ #include #include -#if defined(CONFIG_440SPE) && defined(CONFIG_PCI) +#if (defined(CONFIG_440SPE) || defined(CONFIG_405EX)) && \ + defined(CONFIG_PCI) #include @@ -55,8 +56,10 @@ static u8* pcie_get_base(struct pci_controller *hose, unsigned int devfn) base = (u8*)CFG_PCIE0_XCFGBASE; if (hose->cfg_data == (u8*)CFG_PCIE1_CFGBASE) base = (u8*)CFG_PCIE1_XCFGBASE; +#if CFG_PCIE_NR_PORTS > 2 if (hose->cfg_data == (u8*)CFG_PCIE2_CFGBASE) base = (u8*)CFG_PCIE2_XCFGBASE; +#endif } return base; @@ -68,8 +71,10 @@ static void pcie_dmer_disable(void) mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) | GPL_DMER_MASK_DISA); mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE), mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) | GPL_DMER_MASK_DISA); +#if CFG_PCIE_NR_PORTS > 2 mtdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE), mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) | GPL_DMER_MASK_DISA); +#endif } static void pcie_dmer_enable(void) @@ -78,8 +83,10 @@ static void pcie_dmer_enable(void) mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE0_BASE)) & ~GPL_DMER_MASK_DISA); mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE1_BASE), mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE1_BASE)) & ~GPL_DMER_MASK_DISA); +#if CFG_PCIE_NR_PORTS > 2 mtdcr (DCRN_PEGPL_CFG (DCRN_PCIE2_BASE), mfdcr (DCRN_PEGPL_CFG(DCRN_PCIE2_BASE)) & ~GPL_DMER_MASK_DISA); +#endif } static int pcie_read_config(struct pci_controller *hose, unsigned int devfn, @@ -120,6 +127,7 @@ static int pcie_read_config(struct pci_controller *hose, unsigned int devfn, */ pcie_dmer_disable (); + debug("%s: cfg_data=%08x offset=%08x\n", __func__, hose->cfg_data, offset); switch (len) { case 1: *val = in_8(hose->cfg_data + offset); @@ -227,6 +235,7 @@ int pcie_write_config_dword(struct pci_controller *hose,pci_dev_t dev,int offset return pcie_write_config(hose,(u32)dev,offset,3,(u32 )val); } +#if defined(CONFIG_440SPE) static void ppc4xx_setup_utl(u32 port) { volatile void *utl_base = NULL; @@ -371,6 +380,15 @@ int ppc4xx_init_pcie(void) } return 0; } +#else +int ppc4xx_init_pcie(void) +{ + /* + * Nothing to do on 405EX + */ + return 0; +} +#endif /* * Board-specific pcie initialization @@ -608,19 +626,21 @@ int ppc4xx_init_pcie_port(int port, int rootport) return -1; } +#if defined(CONFIG_440SPE) /* * Setup UTL registers - but only on revA! * We use default settings for revB chip. */ if (!ppc440spe_revB()) ppc4xx_setup_utl(port); +#endif /* * We map PCI Express configuration access into the 512MB regions */ addr = ppc4xx_get_cfgaddr(port); - low = (u32)(addr & 0x00000000ffffffff); - high = (u32)(addr >> 32); + low = U64_TO_U32_LOW(addr); + high = U64_TO_U32_HIGH(addr); switch (port) { case 0: @@ -633,11 +653,13 @@ int ppc4xx_init_pcie_port(int port, int rootport) mtdcr(DCRN_PEGPL_CFGBAL(PCIE1), low); mtdcr(DCRN_PEGPL_CFGMSK(PCIE1), 0xe0000001); /* 512MB region, valid */ break; +#if CFG_PCIE_NR_PORTS > 2 case 2: mtdcr(DCRN_PEGPL_CFGBAH(PCIE2), high); mtdcr(DCRN_PEGPL_CFGBAL(PCIE2), low); mtdcr(DCRN_PEGPL_CFGMSK(PCIE2), 0xe0000001); /* 512MB region, valid */ break; +#endif } /* @@ -692,11 +714,13 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) rmbase = (u32 *)CFG_PCIE1_CFGBASE; hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; break; +#if CFG_PCIE_NR_PORTS > 2 case 2: mbase = (u32 *)CFG_PCIE2_XCFGBASE; rmbase = (u32 *)CFG_PCIE2_CFGBASE; hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; break; +#endif } /* @@ -720,8 +744,8 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) switch (port) { case 0: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), @@ -733,8 +757,8 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE0))); break; case 1: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), @@ -745,9 +769,10 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mfdcr(DCRN_PEGPL_OMR1MSKH(PCIE1)), mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE1))); break; +#if CFG_PCIE_NR_PORTS > 2 case 2: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), @@ -758,6 +783,7 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) mfdcr(DCRN_PEGPL_OMR1MSKH(PCIE2)), mfdcr(DCRN_PEGPL_OMR1MSKL(PCIE2))); break; +#endif } /* Set up 16GB inbound memory window at 0 */ @@ -770,8 +796,8 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) out_le32(mbase + PECFG_PIM01SAL, 0x00000000); out_le32(mbase + PECFG_PIM0LAL, 0); out_le32(mbase + PECFG_PIM0LAH, 0); - out_le32(mbase + PECFG_PIM1LAL, 0x00000000); - out_le32(mbase + PECFG_PIM1LAH, 0x00000004); + out_le32(mbase + PECFG_PIM1LAL, 0x00000000); + out_le32(mbase + PECFG_PIM1LAH, 0x00000004); out_le32(mbase + PECFG_PIMEN, 0x1); /* Enable I/O, Mem, and Busmaster cycles */ @@ -780,23 +806,8 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port) PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); /* Set Device and Vendor Id */ - switch (port) { - case 0: - out_le16(mbase + 0x200, 0xaaa0); - out_le16(mbase + 0x202, 0xbed0); - break; - case 1: - out_le16(mbase + 0x200, 0xaaa1); - out_le16(mbase + 0x202, 0xbed1); - break; - case 2: - out_le16(mbase + 0x200, 0xaaa2); - out_le16(mbase + 0x202, 0xbed2); - break; - default: - out_le16(mbase + 0x200, 0xaaa3); - out_le16(mbase + 0x202, 0xbed3); - } + out_le16(mbase + 0x200, 0xaaa0 + port); + out_le16(mbase + 0x202, 0xbed0 + port); /* Set Class Code to PCI-PCI bridge and Revision Id to 1 */ out_le32(mbase + 0x208, 0x06040001); @@ -826,10 +837,12 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) mbase = (u32 *)CFG_PCIE1_XCFGBASE; hose->cfg_data = (u8 *)CFG_PCIE1_CFGBASE; break; +#if defined(CFG_PCIE2_CFGBASE) case 2: mbase = (u32 *)CFG_PCIE2_XCFGBASE; hose->cfg_data = (u8 *)CFG_PCIE2_CFGBASE; break; +#endif } /* @@ -843,29 +856,31 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) switch (port) { case 0: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE0), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE0), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE0), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE0), ~(CFG_PCIE_MEMSIZE - 1) | 3); break; case 1: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE1), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE1), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE1), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE1), ~(CFG_PCIE_MEMSIZE - 1) | 3); break; +#if CFG_PCIE_NR_PORTS > 2 case 2: - mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), 0x0000000d); - mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + + mtdcr(DCRN_PEGPL_OMR1BAH(PCIE2), CFG_PCIE_ADDR_HIGH); + mtdcr(DCRN_PEGPL_OMR1BAL(PCIE2), CFG_PCIE_MEMBASE + port * CFG_PCIE_MEMSIZE); mtdcr(DCRN_PEGPL_OMR1MSKH(PCIE2), 0x7fffffff); mtdcr(DCRN_PEGPL_OMR1MSKL(PCIE2), ~(CFG_PCIE_MEMSIZE - 1) | 3); break; +#endif } /* Set up 16GB inbound memory window at 0 */ @@ -873,16 +888,16 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) out_le32(mbase + PCI_BASE_ADDRESS_1, 0); out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); out_le32(mbase + PECFG_BAR0LMPA, 0); - out_le32(mbase + PECFG_PIM0LAL, 0x00000000); - out_le32(mbase + PECFG_PIM0LAH, 0x00000004); /* pointing to SRAM */ + out_le32(mbase + PECFG_PIM0LAL, U64_TO_U32_LOW(CFG_PCIE_INBOUND_BASE)); + out_le32(mbase + PECFG_PIM0LAH, U64_TO_U32_HIGH(CFG_PCIE_INBOUND_BASE)); out_le32(mbase + PECFG_PIMEN, 0x1); /* Enable I/O, Mem, and Busmaster cycles */ out_le16((u16 *)(mbase + PCI_COMMAND), in_le16((u16 *)(mbase + PCI_COMMAND)) | PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); - out_le16(mbase + 0x200,0xcaad); /* Setting vendor ID */ - out_le16(mbase + 0x202,0xfeed); /* Setting device ID */ + out_le16(mbase + 0x200, 0xcaad); /* Setting vendor ID */ + out_le16(mbase + 0x202, 0xfeed); /* Setting device ID */ attempts = 10; while(!(SDR_READ(SDRN_PESDR_RCSSTS(port)) & (1 << 8))) { @@ -893,7 +908,7 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) mdelay(1000); } - printf("PCIE:%d successfully set as endpoint\n",port); + printf("PCIE:%d successfully set as endpoint\n", port); return 0; } diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index 1bb8fc7ed13..17ac57b23bc 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -16,14 +16,29 @@ #define DCRN_SDR0_CFGDATA 0x00f #if defined(CONFIG_440SPE) +#define CFG_PCIE_NR_PORTS 3 + +#define CFG_PCIE_ADDR_HIGH 0x0000000d + #define DCRN_PCIE0_BASE 0x100 #define DCRN_PCIE1_BASE 0x120 #define DCRN_PCIE2_BASE 0x140 + +#define PCIE0_SDR 0x300 +#define PCIE1_SDR 0x340 +#define PCIE2_SDR 0x370 #endif #if defined(CONFIG_405EX) +#define CFG_PCIE_NR_PORTS 2 + +#define CFG_PCIE_ADDR_HIGH 0x00000000 + #define DCRN_PCIE0_BASE 0x040 #define DCRN_PCIE1_BASE 0x060 + +#define PCIE0_SDR 0x400 +#define PCIE1_SDR 0x440 #endif #define PCIE0 DCRN_PCIE0_BASE @@ -53,17 +68,6 @@ #define PESDR0_PLLLCT2 0x03a1 #define PESDR0_PLLLCT3 0x03a2 -#if defined(CONFIG_440SPE) -#define PCIE0_SDR 0x300 -#define PCIE1_SDR 0x340 -#define PCIE2_SDR 0x370 -#endif - -#if defined(CONFIG_405EX) -#define PCIE0_SDR 0x400 -#define PCIE1_SDR 0x440 -#endif - /* common regs, at least for 405EX and 440SPe */ #define SDRN_PESDR_UTLSET1(n) (sdr_base(n) + 0x00) #define SDRN_PESDR_UTLSET2(n) (sdr_base(n) + 0x01) @@ -237,6 +241,9 @@ #define GPL_DMER_MASK_DISA 0x02000000 +#define U64_TO_U32_LOW(val) ((u32)((val) & 0x00000000ffffffffULL)) +#define U64_TO_U32_HIGH(val) ((u32)((val) >> 32)) + int ppc4xx_init_pcie(void); int ppc4xx_init_pcie_rootport(int port); int ppc4xx_init_pcie_endport(int port); @@ -260,7 +267,7 @@ static inline u32 sdr_base(int port) return PCIE0_SDR; case 1: return PCIE1_SDR; -#if defined(PCIE2_SDR) +#if CFG_PCIE_NR_PORTS > 2 case 2: return PCIE2_SDR; #endif diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 03c3cb3bdf0..8a963279f08 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -72,6 +72,9 @@ #define CFG_PCIE1_XCFGBASE 0xc3001000 #define CFG_PCIE2_XCFGBASE 0xc3002000 +/* base address of inbound PCIe window */ +#define CFG_PCIE_INBOUND_BASE 0x0000000400000000ULL + /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE #define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 6caf21bcb51..ab7fb0ab8c2 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -74,6 +74,9 @@ #define CFG_PCIE1_XCFGBASE 0xc3001000 #define CFG_PCIE2_XCFGBASE 0xc3002000 +/* base address of inbound PCIe window */ +#define CFG_PCIE_INBOUND_BASE 0x0000000400000000ULL + /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE #define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE -- cgit v1.3.1 From 4f2e92c11f6e2392fc8187829211a5ca7f0c1e12 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 15:10:02 +0200 Subject: DTT: Prepare DS1775 driver for use of different I2C addresses Signed-off-by: Stefan Roese --- dtt/ds1775.c | 2 +- include/configs/taihu.h | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/dtt/ds1775.c b/dtt/ds1775.c index e44cee3279c..0fbb0b42a78 100644 --- a/dtt/ds1775.c +++ b/dtt/ds1775.c @@ -25,7 +25,7 @@ #include #include -#define DTT_I2C_DEV_CODE 0x49 /* Dallas Semi's DS1775 device code */ +#define DTT_I2C_DEV_CODE CFG_I2C_DTT_ADDR /* Dallas Semi's DS1775 device code */ int dtt_read(int sensor, int reg) { diff --git a/include/configs/taihu.h b/include/configs/taihu.h index d623e56009a..6d204a9b575 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -244,6 +244,7 @@ unsigned char spi_read(void); /* standard dtt sensor configuration */ #define CONFIG_DTT_DS1775 1 #define CONFIG_DTT_SENSORS { 0 } +#define CFG_I2C_DTT_ADDR 0x49 /*----------------------------------------------------------------------- * PCI stuff -- cgit v1.3.1 From dbbd125721aea6645fdb962f36bd41f59e272f9d Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 17:10:59 +0200 Subject: ppc4xx: Add PPC405EX support Signed-off-by: Stefan Roese --- common/serial.c | 6 +- cpu/ppc4xx/4xx_enet.c | 113 ++++++-- cpu/ppc4xx/Makefile | 2 +- cpu/ppc4xx/cpu.c | 63 +++-- cpu/ppc4xx/cpu_init.c | 14 +- cpu/ppc4xx/interrupts.c | 20 +- cpu/ppc4xx/miiphy.c | 22 +- cpu/ppc4xx/ndfc.c | 3 +- cpu/ppc4xx/serial.c | 42 ++- cpu/ppc4xx/speed.c | 180 +++++++++++- cpu/ppc4xx/start.S | 69 +++-- cpu/ppc4xx/vecnum.h | 104 +++++++ include/405_mal.h | 4 +- include/4xx_i2c.h | 2 +- include/asm-ppc/processor.h | 4 + include/asm-ppc/u-boot.h | 1 + include/common.h | 4 +- include/ppc405.h | 675 ++++++++++++++++++++++++++++++++++++++++++-- include/ppc440.h | 2 +- include/ppc4xx_enet.h | 15 +- include/serial.h | 5 +- 21 files changed, 1205 insertions(+), 145 deletions(-) (limited to 'include') diff --git a/common/serial.c b/common/serial.c index dee1cc0ab9c..b9916e2b5ec 100644 --- a/common/serial.c +++ b/common/serial.c @@ -41,7 +41,8 @@ struct serial_device *default_serial_console (void) || defined(CONFIG_8xx_CONS_SCC3) || defined(CONFIG_8xx_CONS_SCC4) return &serial_scc_device; #elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \ - || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx) + || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_405EX) \ + || defined(CONFIG_MPC5xxx) #if defined(CONFIG_CONS_INDEX) && defined(CFG_NS16550_SERIAL) #if (CONFIG_CONS_INDEX==1) return &eserial1_device; @@ -91,7 +92,8 @@ void serial_initialize (void) #endif #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \ - || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx) + || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_405EX) \ + || defined(CONFIG_MPC5xxx) serial_register(&serial0_device); serial_register(&serial1_device); #endif diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 71a9e372da0..841cb77d6de 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -133,13 +133,15 @@ #define BI_PHYMODE_GMII 3 #define BI_PHYMODE_RTBI 4 #define BI_PHYMODE_TBI 5 -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define BI_PHYMODE_SMII 6 #define BI_PHYMODE_MII 7 #endif -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || \ - defined(CONFIG_440GRX) || defined(CONFIG_440SP) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define SDR0_MFR_ETH_CLK_SEL_V(n) ((0x01<<27) / (n+1)) #endif @@ -172,6 +174,12 @@ struct eth_device *emac0_dev = NULL; #define CONFIG_EMAC_NR_START 0 #endif +#if defined(CONFIG_405EX) || defined(CONFIG_440EPX) +#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev))) +#else +#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * 2)) +#endif + /*-----------------------------------------------------------------------------+ * Prototypes and externals. *-----------------------------------------------------------------------------*/ @@ -197,7 +205,9 @@ static void ppc_4xx_eth_halt (struct eth_device *dev) { EMAC_4XX_HW_PST hw_p = dev->priv; uint32_t failsafe = 10000; -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) unsigned long mfr; #endif @@ -221,7 +231,9 @@ static void ppc_4xx_eth_halt (struct eth_device *dev) } /* EMAC RESET */ -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) /* provide clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); mfr |= SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum); @@ -230,7 +242,9 @@ static void ppc_4xx_eth_halt (struct eth_device *dev) out32 (EMAC_M0 + hw_p->hw_addr, EMAC_M0_SRST); -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) /* remove clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(hw_p->devnum); @@ -389,6 +403,38 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) } #endif /* CONFIG_440EPX */ +#if defined(CONFIG_405EX) +int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) +{ + u32 gmiifer = 0; + + /* + * Right now only 2*RGMII is supported. Please extend when needed. + * sr - 2007-09-19 + */ + switch (1) { + case 1: + /* 2 x RGMII ports */ + out32 (RGMII_FER, 0x00000055); + bis->bi_phymode[0] = BI_PHYMODE_RGMII; + bis->bi_phymode[1] = BI_PHYMODE_RGMII; + break; + case 2: + /* 2 x SMII ports */ + break; + default: + break; + } + + /* Ensure we setup mdio for this devnum and ONLY this devnum */ + gmiifer = in32(RGMII_FER); + gmiifer |= (1 << (19-devnum)); + out32 (RGMII_FER, gmiifer); + + return ((int)0x0); +} +#endif /* CONFIG_405EX */ + static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) { int i, j; @@ -402,19 +448,21 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) unsigned short reg_short; #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) sys_info_t sysinfo; #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) int ethgroup = -1; #endif #endif #if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) unsigned long mfr; #endif - EMAC_4XX_HW_PST hw_p = dev->priv; /* before doing anything, figure out if we have a MAC address */ @@ -426,7 +474,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) /* Need to get the OPB frequency so we can access the PHY */ get_sys_info (&sysinfo); #endif @@ -498,12 +547,16 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) out32 (ZMII_SSR, ZMII_SSR_SP << ZMII_SSR_V(devnum)); #endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */ +#if defined(CONFIG_405EX) + ethgroup = ppc_4xx_eth_setup_bridge(devnum, bis); +#endif __asm__ volatile ("eieio"); /* reset emac so we have access to the phy */ -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) /* provide clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); mfr |= SDR0_MFR_ETH_CLK_SEL_V(devnum); @@ -521,8 +574,9 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) if (failsafe <= 0) printf("\nProblem resetting EMAC!\n"); -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) +#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) /* remove clocks for EMAC internal loopback */ mfsdr (sdr_mfr, mfr); mfr &= ~SDR0_MFR_ETH_CLK_SEL_V(devnum); @@ -531,7 +585,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) /* Whack the M1 register */ mode_reg = 0x0; mode_reg &= ~0x00000038; @@ -591,7 +646,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) #if defined(CONFIG_CIS8201_PHY) /* @@ -723,7 +779,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) } #endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */ -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) if (speed == 1000) reg = (RGMII_SSR_SP_1000MBPS << RGMII_SSR_V (devnum)); else if (speed == 100) @@ -740,7 +797,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) /* set the Mal configuration reg */ #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) mtdcr (malmcr, MAL_CR_PLBB | MAL_CR_OPBBL | MAL_CR_LEA | MAL_CR_PLBLT_DEFAULT | MAL_CR_EOPIE | 0x00330000); #else @@ -978,8 +1036,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) /* * Connect interrupt service routines */ - irq_install_handler (VECNUM_ETH0 + (hw_p->devnum * 2), - (interrupt_handler_t *) enetInt, dev); + irq_install_handler(ETH_IRQ_NUM(hw_p->devnum), + (interrupt_handler_t *) enetInt, dev); } mtmsr (msr); /* enable interrupts again */ @@ -1059,7 +1117,7 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, } -#if defined (CONFIG_440) +#if defined (CONFIG_440) || defined(CONFIG_405EX) #if defined(CONFIG_440SP) || defined(CONFIG_440SPE) /* @@ -1073,7 +1131,8 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, #define UIC0SR uic0sr #endif -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define UICMSR_ETHX uic0msr #define UICSR_ETHX uic0sr #else @@ -1601,7 +1660,11 @@ int ppc_4xx_eth_initialize (bd_t * bis) bis->bi_phynum[3] = CONFIG_PHY3_ADDR; bis->bi_phymode[2] = 2; bis->bi_phymode[3] = 2; +#endif +#if defined(CONFIG_440GX) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) ppc_4xx_eth_setup_bridge(0, bis); #endif @@ -1649,7 +1712,9 @@ int ppc_4xx_eth_initialize (bd_t * bis) if (0 == virgin) { /* set the MAL IER ??? names may change with new spec ??? */ -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) mal_ier = MAL_IER_PT | MAL_IER_PRE | MAL_IER_PWE | MAL_IER_DE | MAL_IER_OTE | MAL_IER_OE | MAL_IER_PE ; diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index a11faec14e1..bc65aa0571d 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -30,7 +30,7 @@ SOBJS = dcr.o COBJS = 40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o \ 4xx_pci.o 4xx_pcie.o 4xx_enet.o \ bedbug_405.o commproc.o \ - cpu.o cpu_init.o gpio.o i2c.o interrupts.o \ + cpu.o cpu_init.o fdt.o gpio.o i2c.o interrupts.o \ miiphy.o ndfc.o sdram.o serial.o speed.o \ tlb.o traps.o usb_ohci.o usb.o usbdev.o diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index c07bc0c325e..7addb9251f5 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2000-2006 + * (C) Copyright 2000-2007 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this @@ -45,15 +45,6 @@ DECLARE_GLOBAL_DATA_PTR; void board_reset(void); #endif -#if defined(CONFIG_440) -#define FREQ_EBC (sys_info.freqEPB) -#elif defined(CONFIG_405EZ) -#define FREQ_EBC ((CONFIG_SYS_CLK_FREQ * sys_info.pllFbkDiv) / \ - sys_info.pllExtBusDiv) -#else -#define FREQ_EBC (sys_info.freqPLB / sys_info.pllExtBusDiv) -#endif - #if defined(CONFIG_405GP) || \ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) @@ -76,7 +67,8 @@ int pci_async_enabled(void) } #endif -#if defined(CONFIG_PCI) && !defined(CONFIG_IOP480) && !defined(CONFIG_405) +#if defined(CONFIG_PCI) && !defined(CONFIG_IOP480) && \ + !defined(CONFIG_405) && !defined(CONFIG_405EX) int pci_arbiter_enabled(void) { #if defined(CONFIG_405GP) @@ -110,7 +102,8 @@ int pci_arbiter_enabled(void) #if defined(CONFIG_405EP) || defined(CONFIG_440GX) || \ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) #define I2C_BOOTROM @@ -207,6 +200,21 @@ static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'F', 'G', 'H', \ 'I', 'x', 'K', 'L', 'M', 'N', 'O', 'P' }; #endif +#if defined(CONFIG_405EX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "EBC (16 bits)", + "EBC (16 bits)", + "NAND (8 bits)", + "NAND (8 bits)", + "I2C (Addr 0x54)", + "EBC (8 bits)", + "I2C (Addr 0x52)", +}; +static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G', 'F', 'H' }; +#endif + #if defined(SDR0_PINSTP_SHIFT) static int bootstrap_option(void) { @@ -241,7 +249,8 @@ int checkcpu (void) puts("AMCC PowerPC 4"); #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ - defined(CONFIG_405EP) || defined(CONFIG_405EZ) + defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ + defined(CONFIG_405EX) puts("05"); #endif #if defined(CONFIG_440) @@ -293,6 +302,26 @@ int checkcpu (void) puts("EZ Rev. A"); break; + case PVR_405EX1_RA: + puts("EX Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_405EX2_RA: + puts("EX Rev. A"); + strcpy(addstr, "No Security support"); + break; + + case PVR_405EXR1_RA: + puts("EXr Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_405EXR2_RA: + puts("EXr Rev. A"); + strcpy(addstr, "No Security support"); + break; + #if defined(CONFIG_440) case PVR_440GP_RB: puts("GP Rev. B"); @@ -424,7 +453,7 @@ int checkcpu (void) printf (" at %s MHz (PLB=%lu, OPB=%lu, EBC=%lu MHz)\n", strmhz(buf, clock), sys_info.freqPLB / 1000000, get_OPB_freq() / 1000000, - FREQ_EBC / 1000000); + sys_info.freqEBC / 1000000); if (addstr[0] != 0) printf(" %s\n", addstr); @@ -437,7 +466,7 @@ int checkcpu (void) printf ("Boot ROM Location %s\n", bootstrap_str[bootstrap_option()]); #endif /* SDR0_PINSTP_SHIFT */ -#if defined(CONFIG_PCI) +#if defined(CONFIG_PCI) && !defined(CONFIG_405EX) printf (" Internal PCI arbiter %sabled", pci_arbiter_enabled() ? "en" : "dis"); #endif @@ -450,11 +479,11 @@ int checkcpu (void) } #endif -#if defined(CONFIG_PCI) +#if defined(CONFIG_PCI) && !defined(CONFIG_405EX) putc('\n'); #endif -#if defined(CONFIG_405EP) || defined(CONFIG_405EZ) +#if defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_405EX) printf (" 16 kB I-Cache 16 kB D-Cache"); #elif defined(CONFIG_440) printf (" 32 kB I-Cache 32 kB D-Cache"); diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c index 351da36e855..afb94cc0700 100644 --- a/cpu/ppc4xx/cpu_init.c +++ b/cpu/ppc4xx/cpu_init.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2000-2006 + * (C) Copyright 2000-2007 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this @@ -112,7 +112,7 @@ cpu_init_f (void) unsigned long val; #endif -#if defined(CONFIG_405EP) +#if defined(CONFIG_405EP) || defined (CONFIG_405EX) /* * GPIO0 setup (select GPIO or alternate function) */ @@ -128,13 +128,21 @@ cpu_init_f (void) out32(GPIO0_ISR1L, CFG_GPIO0_ISR1L); out32(GPIO0_TSRH, CFG_GPIO0_TSRH); /* three-state select */ out32(GPIO0_TSRL, CFG_GPIO0_TSRL); +#if defined(CFG_GPIO0_ISR2H) + out32(GPIO0_ISR2H, CFG_GPIO0_ISR2H); + out32(GPIO0_ISR2L, CFG_GPIO0_ISR2L); +#endif +#if defined (CFG_GPIO0_TCR) out32(GPIO0_TCR, CFG_GPIO0_TCR); /* enable output driver for outputs */ +#endif +#if defined (CONFIG_450EP) /* * Set EMAC noise filter bits */ mtdcr(cpc0_epctl, CPC0_EPRCSR_E0NFE | CPC0_EPRCSR_E1NFE); #endif /* CONFIG_405EP */ +#endif /* CONFIG_405EP */ #if defined(CFG_440_GPIO_TABLE) gpio_set_chip_configuration(); @@ -146,7 +154,7 @@ cpu_init_f (void) #if (defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR)) #if (defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_405)) + defined(CONFIG_405EX) || defined(CONFIG_405)) /* * Move the next instructions into icache, since these modify the flash * we are running from! diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c index ca565cc3e07..2026cc927a9 100644 --- a/cpu/ppc4xx/interrupts.c +++ b/cpu/ppc4xx/interrupts.c @@ -52,7 +52,7 @@ struct irq_action { static struct irq_action irq_vecs[32]; void uic0_interrupt( void * parms); /* UIC0 handler */ -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) static struct irq_action irq_vecs1[32]; /* For UIC1 */ void uic1_interrupt( void * parms); /* UIC1 handler */ @@ -116,7 +116,7 @@ int interrupt_init_cpu (unsigned *decrementer_count) irq_vecs[vec].handler = NULL; irq_vecs[vec].arg = NULL; irq_vecs[vec].count = 0; -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) irq_vecs1[vec].handler = NULL; irq_vecs1[vec].arg = NULL; irq_vecs1[vec].count = 0; @@ -172,7 +172,7 @@ int interrupt_init_cpu (unsigned *decrementer_count) */ set_evpr(0x00000000); -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) #if !defined(CONFIG_440GX) /* Install the UIC1 handlers */ irq_install_handler(VECNUM_UIC1NC, uic1_interrupt, 0); @@ -378,7 +378,7 @@ void uic0_interrupt( void * parms) #endif /* CONFIG_440GX */ -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) /* Handler for UIC1 interrupt */ void uic1_interrupt( void * parms) { @@ -525,7 +525,7 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg) struct irq_action *irqa = irq_vecs; int i = vec; -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) { @@ -553,7 +553,7 @@ void irq_install_handler (int vec, interrupt_handler_t * handler, void *arg) irqa[i].handler = handler; irqa[i].arg = arg; -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) @@ -577,7 +577,7 @@ void irq_free_handler (int vec) struct irq_action *irqa = irq_vecs; int i = vec; -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) { @@ -599,7 +599,7 @@ void irq_free_handler (int vec) vec, irq_vecs[vec].handler); #endif -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) if ((vec > 31) && (vec < 64)) @@ -641,7 +641,7 @@ do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int vec; printf ("\nInterrupt-Information:\n"); -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) printf ("\nUIC 0\n"); #endif printf ("Nr Routine Arg Count\n"); @@ -656,7 +656,7 @@ do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) } } -#if defined(CONFIG_440) +#if defined(CONFIG_440) || defined(CONFIG_405EX) printf ("\nUIC 1\n"); printf ("Nr Routine Arg Count\n"); diff --git a/cpu/ppc4xx/miiphy.c b/cpu/ppc4xx/miiphy.c index 6b98025308f..2c675e9be6b 100644 --- a/cpu/ppc4xx/miiphy.c +++ b/cpu/ppc4xx/miiphy.c @@ -141,6 +141,16 @@ unsigned int miiphy_getemac_offset (void) return (eoffset); #else + +#if defined(CONFIG_NET_MULTI) && defined(CONFIG_405EX) + unsigned long rgmii; + int devnum = 1; + + rgmii = in32(RGMII_FER); + if (rgmii & (1 << (19 - devnum))) + return 0x100; +#endif + return 0; #endif } @@ -174,7 +184,8 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, sta_reg = reg; /* reg address */ /* set clock (50Mhz) and read flags */ #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_READ; #else @@ -186,7 +197,8 @@ int emac4xx_miiphy_read (char *devname, unsigned char addr, #if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && \ !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ - !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \ + !defined(CONFIG_405EX) sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; #endif sta_reg = sta_reg | (addr << 5); /* Phy address */ @@ -248,7 +260,8 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr, sta_reg = reg; /* reg address */ /* set clock (50Mhz) and read flags */ #if defined(CONFIG_440GX) || defined(CONFIG_440SPE) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #if defined(CONFIG_IBM_EMAC4_V4) /* EMAC4 V4 changed bit setting */ sta_reg = (sta_reg & ~EMAC_STACR_OP_MASK) | EMAC_STACR_WRITE; #else @@ -260,7 +273,8 @@ int emac4xx_miiphy_write (char *devname, unsigned char addr, #if defined(CONFIG_PHY_CLK_FREQ) && !defined(CONFIG_440GX) && \ !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) && \ - !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) + !defined(CONFIG_440EPX) && !defined(CONFIG_440GRX) && \ + !defined(CONFIG_405EX) sta_reg = sta_reg | CONFIG_PHY_CLK_FREQ; /* Set clock frequency (PLB freq. dependend) */ #endif sta_reg = sta_reg | ((unsigned long) addr << 5);/* Phy address */ diff --git a/cpu/ppc4xx/ndfc.c b/cpu/ppc4xx/ndfc.c index 398457726f4..ec1b38cffa3 100644 --- a/cpu/ppc4xx/ndfc.c +++ b/cpu/ppc4xx/ndfc.c @@ -34,7 +34,7 @@ #if defined(CONFIG_CMD_NAND) && !defined(CFG_NAND_LEGACY) && \ (defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_405EZ)) + defined(CONFIG_405EZ) || defined(CONFIG_405EX)) #include #include @@ -222,6 +222,7 @@ int board_nand_init(struct nand_chip *nand) */ board_nand_select_device(nand, cs); out_be32((u32 *)(base + NDFC_BCFG0 + (cs << 2)), 0x80002222); + return 0; } diff --git a/cpu/ppc4xx/serial.c b/cpu/ppc4xx/serial.c index 60712b151e2..8b1e2ffa0b4 100644 --- a/cpu/ppc4xx/serial.c +++ b/cpu/ppc4xx/serial.c @@ -266,7 +266,7 @@ int serial_tstc () /*****************************************************************************/ #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_440) + defined(CONFIG_405EX) || defined(CONFIG_440) #if defined(CONFIG_440) #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ @@ -318,6 +318,15 @@ int serial_tstc () #define UCR0_UDIV_POS 0 #define UCR1_UDIV_POS 8 #define UDIV_MAX 127 +#elif defined(CONFIG_405EX) +#define UART0_BASE 0xef600200 +#define UART1_BASE 0xef600300 +#define CR0_MASK 0x000000ff +#define CR0_EXTCLK_ENA 0x00800000 +#define CR0_UDIV_POS 0 +#define UDIV_SUBTRACT 0 +#define UART0_SDR sdr_uart0 +#define UART1_SDR sdr_uart1 #else /* CONFIG_405GP || CONFIG_405CR */ #define UART0_BASE 0xef600300 #define UART1_BASE 0xef600400 @@ -391,7 +400,8 @@ typedef struct { volatile static serial_buffer_t buf_info; #endif -#if defined(CONFIG_440) && !defined(CFG_EXT_SERIAL_CLOCK) +#if (defined(CONFIG_440) || defined(CONFIG_405EX)) && \ + !defined(CFG_EXT_SERIAL_CLOCK) static void serial_divs (int baudrate, unsigned long *pudiv, unsigned short *pbdiv) { @@ -572,7 +582,31 @@ int serial_init (void) unsigned short bdiv; volatile char val; -#if defined(CONFIG_405EZ) +#ifdef CONFIG_405EX + clk = tmp = 0; + mfsdr(UART0_SDR, reg); + reg &= ~CR0_MASK; +#ifdef CFG_EXT_SERIAL_CLOCK + reg |= CR0_EXTCLK_ENA; + udiv = 1; + tmp = gd->baudrate * 16; + bdiv = (CFG_EXT_SERIAL_CLOCK + tmp / 2) / tmp; +#else + serial_divs(gd->baudrate, &udiv, &bdiv); +#endif + reg |= (udiv - UDIV_SUBTRACT) << CR0_UDIV_POS; /* set the UART divisor */ + + /* + * Configure input clock to baudrate generator for all + * available serial ports here + */ + mtsdr(UART0_SDR, reg); + +#if defined(UART1_SDR) + mtsdr(UART1_SDR, reg); +#endif + +#elif defined(CONFIG_405EZ) serial_divs(gd->baudrate, &udiv, &bdiv); clk = tmp = reg = 0; #else @@ -608,7 +642,7 @@ int serial_init (void) #endif /* CONFIG_405EP */ tmp = gd->baudrate * udiv * 16; bdiv = (clk + tmp / 2) / tmp; -#endif /* CONFIG_405EZ */ +#endif /* CONFIG_405EX */ out8(UART_BASE + UART_LCR, 0x80); /* set DLAB bit */ out8(UART_BASE + UART_DLL, bdiv); /* set baudrate divisor */ diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c index da5330a3604..750b0958762 100644 --- a/cpu/ppc4xx/speed.c +++ b/cpu/ppc4xx/speed.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2000 + * (C) Copyright 2000-2007 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * * See file CREDITS for list of people who contributed to this @@ -263,7 +263,7 @@ void get_sys_info (sys_info_t *sysInfo) sysInfo->freqProcessor = sysInfo->freqVCOMhz/sysInfo->pllFwdDivA; sysInfo->freqPLB = sysInfo->freqVCOMhz/sysInfo->pllFwdDivB/prbdv0; sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv; - sysInfo->freqEPB = sysInfo->freqPLB/sysInfo->pllExtBusDiv; + sysInfo->freqEBC = sysInfo->freqPLB/sysInfo->pllExtBusDiv; sysInfo->freqPCI = sysInfo->freqPLB/sysInfo->pllPciDiv; /* Figure which timer source to use */ @@ -317,7 +317,7 @@ void get_sys_info (sys_info_t * sysInfo) if( get_pvr() == PVR_440GP_RB ) /* Rev B divs an extra 2 -- geez! */ sysInfo->freqPLB >>= 1; sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv; - sysInfo->freqEPB = sysInfo->freqOPB/sysInfo->pllExtBusDiv; + sysInfo->freqEBC = sysInfo->freqOPB/sysInfo->pllExtBusDiv; } #else @@ -393,7 +393,7 @@ void get_sys_info (sys_info_t * sysInfo) sysInfo->freqProcessor = sysInfo->freqVCOMhz/sysInfo->pllFwdDivA; sysInfo->freqPLB = sysInfo->freqVCOMhz/sysInfo->pllFwdDivB/prbdv0; sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv; - sysInfo->freqEPB = sysInfo->freqOPB/sysInfo->pllExtBusDiv; + sysInfo->freqEBC = sysInfo->freqOPB/sysInfo->pllExtBusDiv; #if defined(CONFIG_YUCCA) /* Determine PCI Clock Period */ @@ -733,6 +733,8 @@ void get_sys_info (PPC405_SYS_INFO * sysInfo) * Determine PLB clock frequency */ sysInfo->freqPLB = sysInfo->freqProcessor / sysInfo->pllPlbDiv; + + sysInfo->freqEBC = sysInfo->freqPLB / sysInfo->pllExtBusDiv; } @@ -856,6 +858,9 @@ void get_sys_info (PPC405_SYS_INFO * sysInfo) */ sysInfo->freqPLB = (CONFIG_SYS_CLK_FREQ * m) / sysInfo->pllFwdDiv / sysInfo->pllPlbDiv; + + sysInfo->freqEBC = (CONFIG_SYS_CLK_FREQ * sysInfo->pllFbkDiv) / + sysInfo->pllExtBusDiv; } /******************************************** @@ -874,13 +879,175 @@ ulong get_OPB_freq (void) return val; } +#elif defined(CONFIG_405EX) + +/* + * TODO: We need to get the CPR registers and calculate these values correctly!!!! + * We need the specs!!!! + */ +static unsigned char get_fbdv(unsigned char index) +{ + unsigned char ret = 0; + /* This is table should be 256 bytes. + * Only take first 52 values. + */ + unsigned char fbdv_tb[] = { + 0x00, 0xff, 0x7f, 0xfd, + 0x7a, 0xf5, 0x6a, 0xd5, + 0x2a, 0xd4, 0x29, 0xd3, + 0x26, 0xcc, 0x19, 0xb3, + 0x67, 0xce, 0x1d, 0xbb, + 0x77, 0xee, 0x5d, 0xba, + 0x74, 0xe9, 0x52, 0xa5, + 0x4b, 0x96, 0x2c, 0xd8, + 0x31, 0xe3, 0x46, 0x8d, + 0x1b, 0xb7, 0x6f, 0xde, + 0x3d, 0xfb, 0x76, 0xed, + 0x5a, 0xb5, 0x6b, 0xd6, + 0x2d, 0xdb, 0x36, 0xec, + + }; + + if ((index & 0x7f) == 0) + return 1; + while (ret < sizeof (fbdv_tb)) { + if (fbdv_tb[ret] == index) + break; + ret++; + } + ret++; + + return ret; +} + +#define PLL_FBK_PLL_LOCAL 0 +#define PLL_FBK_CPU 1 +#define PLL_FBK_PERCLK 5 + +void get_sys_info (sys_info_t * sysInfo) +{ + unsigned long sysClkPeriodPs = ONE_BILLION / (CONFIG_SYS_CLK_FREQ / 1000); + unsigned long m = 1; + unsigned int tmp; + unsigned char fwdva[16] = { + 1, 2, 14, 9, 4, 11, 16, 13, + 12, 5, 6, 15, 10, 7, 8, 3, + }; + unsigned char sel, cpudv0, plb2xDiv; + + mfcpr(cpr0_plld, tmp); + + /* + * Determine forward divider A + */ + sysInfo->pllFwdDiv = fwdva[((tmp >> 16) & 0x0f)]; /* FWDVA */ + + /* + * Determine FBK_DIV. + */ + sysInfo->pllFbkDiv = get_fbdv(((tmp >> 24) & 0x0ff)); /* FBDV */ + + /* + * Determine PLBDV0 + */ + sysInfo->pllPlbDiv = 2; + + /* + * Determine PERDV0 + */ + mfcpr(cpr0_perd, tmp); + tmp = (tmp >> 24) & 0x03; + sysInfo->pllExtBusDiv = (tmp == 0) ? 4 : tmp; + + /* + * Determine OPBDV0 + */ + mfcpr(cpr0_opbd, tmp); + tmp = (tmp >> 24) & 0x03; + sysInfo->pllOpbDiv = (tmp == 0) ? 4 : tmp; + + /* Determine PLB2XDV0 */ + mfcpr(cpr0_plbd, tmp); + tmp = (tmp >> 16) & 0x07; + plb2xDiv = (tmp == 0) ? 8 : tmp; + + /* Determine CPUDV0 */ + mfcpr(cpr0_cpud, tmp); + tmp = (tmp >> 24) & 0x07; + cpudv0 = (tmp == 0) ? 8 : tmp; + + /* Determine SEL(5:7) in CPR0_PLLC */ + mfcpr(cpr0_pllc, tmp); + sel = (tmp >> 24) & 0x07; + + /* + * Determine the M factor + * PLL local: M = FBDV + * CPU clock: M = FBDV * FWDVA * CPUDV0 + * PerClk : M = FBDV * FWDVA * PLB2XDV0 * PLBDV0(2) * OPBDV0 * PERDV0 + * + */ + switch (sel) { + case PLL_FBK_CPU: + m = sysInfo->pllFwdDiv * cpudv0; + break; + case PLL_FBK_PERCLK: + m = sysInfo->pllFwdDiv * plb2xDiv * 2 + * sysInfo->pllOpbDiv * sysInfo->pllExtBusDiv; + break; + case PLL_FBK_PLL_LOCAL: + break; + default: + printf("%s unknown m\n", __FUNCTION__); + return; + + } + m *= sysInfo->pllFbkDiv; + + /* + * Determine VCO clock frequency + */ + sysInfo->freqVCOHz = (1000000000000LL * (unsigned long long)m) / + (unsigned long long)sysClkPeriodPs; + + /* + * Determine CPU clock frequency + */ + sysInfo->freqProcessor = sysInfo->freqVCOHz / (sysInfo->pllFwdDiv * cpudv0); + + /* + * Determine PLB clock frequency, ddr1x should be the same + */ + sysInfo->freqPLB = sysInfo->freqVCOHz / (sysInfo->pllFwdDiv * plb2xDiv * 2); + sysInfo->freqOPB = sysInfo->freqPLB/sysInfo->pllOpbDiv; + sysInfo->freqDDR = sysInfo->freqPLB; + sysInfo->freqEBC = sysInfo->freqOPB / sysInfo->pllExtBusDiv; +} + +/******************************************** + * get_OPB_freq + * return OPB bus freq in Hz + *********************************************/ +ulong get_OPB_freq (void) +{ + ulong val = 0; + + PPC405_SYS_INFO sys_info; + + get_sys_info (&sys_info); + val = sys_info.freqPLB / sys_info.pllOpbDiv; + + return val; +} + #endif int get_clocks (void) { #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_440) || defined(CONFIG_405) + defined(CONFIG_405EX) || defined(CONFIG_405) || \ + defined(CONFIG_440) sys_info_t sys_info; get_sys_info (&sys_info); @@ -907,7 +1074,8 @@ ulong get_bus_freq (ulong dummy) #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_440) || defined(CONFIG_405) + defined(CONFIG_405EX) || defined(CONFIG_405) || \ + defined(CONFIG_440) sys_info_t sys_info; get_sys_info (&sys_info); diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 9626b65c885..81a15fe922d 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -800,7 +800,7 @@ _start: /*----------------------------------------------------------------------- */ /* Enable two 128MB cachable regions. */ /*----------------------------------------------------------------------- */ - addis r1,r0,0x8000 + addis r1,r0,0xc000 addi r1,r1,0x0001 mticcr r1 /* instruction cache */ @@ -823,12 +823,23 @@ _start: /*****************************************************************************/ #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ - defined(CONFIG_405) + defined(CONFIG_405EX) || defined(CONFIG_405) /*----------------------------------------------------------------------- */ /* Clear and set up some registers. */ /*----------------------------------------------------------------------- */ addi r4,r0,0x0000 +#if !defined(CONFIG_405EX) mtspr sgr,r4 +#else + /* + * On 405EX, completely clearing the SGR leads to PPC hangup + * upon PCIe configuration access. The PCIe memory regions + * need to be guarded! + */ + lis r3,0x0000 + ori r3,r3,0x7FFC + mtspr sgr,r3 +#endif mtspr dcwr,r4 mtesr r4 /* clear Exception Syndrome Reg */ mttcr r4 /* clear Timer Control Reg */ @@ -851,7 +862,7 @@ _start: /*----------------------------------------------------------------------- */ /* Enable two 128MB cachable regions. */ /*----------------------------------------------------------------------- */ - lis r4,0x8000 + lis r4,0xc000 ori r4,r4,0x0001 mticcr r4 /* instruction cache */ isync @@ -860,12 +871,34 @@ _start: ori r4,r4,0x0000 mtdccr r4 /* data cache */ -#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR)) +#if !(defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR)) || defined(CONFIG_405EX) /*----------------------------------------------------------------------- */ /* Tune the speed and size for flash CS0 */ /*----------------------------------------------------------------------- */ bl ext_bus_cntlr_init #endif +#if !(defined(CFG_INIT_DCACHE_CS) || defined(CFG_TEMP_STACK_OCM)) + /* + * Boards like the Kilauea (405EX) don't have OCM and can't use + * DCache for init-ram. So setup stack here directly after the + * SDRAM is initialized. + */ + lis r1, CFG_INIT_RAM_ADDR@h + ori r1,r1,CFG_INIT_SP_OFFSET /* set up the stack in SDRAM */ + + li r0, 0 /* Make room for stack frame header and */ + stwu r0, -4(r1) /* clear final stack frame so that */ + stwu r0, -4(r1) /* stack backtraces terminate cleanly */ + /* + * Set up a dummy frame to store reset vector as return address. + * this causes stack underflow to reset board. + */ + stwu r1, -8(r1) /* Save back chain and move SP */ + lis r0, RESET_VECTOR@h /* Address of reset vector */ + ori r0, r0, RESET_VECTOR@l + stwu r1, -8(r1) /* Save back chain and move SP */ + stw r0, +12(r1) /* Save return addr (underflow vect) */ +#endif /* !(CFG_INIT_DCACHE_CS || !CFG_TEM_STACK_OCM) */ #if defined(CONFIG_405EP) /*----------------------------------------------------------------------- */ @@ -983,7 +1016,7 @@ start_ram: ori r4,r4,0xa000 mtdcr ebccfgd,r4 - /* turn on data chache for this region */ + /* turn on data cache for this region */ lis r4,0x0080 mtdccr r4 @@ -1049,30 +1082,6 @@ start_ram: /*----------------------------------------------------------------------- */ bl sdram_init - /* - * Setup temporary stack pointer only for boards - * that do not use SDRAM SPD I2C stuff since it - * is already initialized to use DCACHE or OCM - * stacks. - */ -#if !(defined(CFG_INIT_DCACHE_CS) || defined(CFG_TEMP_STACK_OCM)) - lis r1, CFG_INIT_RAM_ADDR@h - ori r1,r1,CFG_INIT_SP_OFFSET /* set up the stack in SDRAM */ - - li r0, 0 /* Make room for stack frame header and */ - stwu r0, -4(r1) /* clear final stack frame so that */ - stwu r0, -4(r1) /* stack backtraces terminate cleanly */ - /* - * Set up a dummy frame to store reset vector as return address. - * this causes stack underflow to reset board. - */ - stwu r1, -8(r1) /* Save back chain and move SP */ - lis r0, RESET_VECTOR@h /* Address of reset vector */ - ori r0, r0, RESET_VECTOR@l - stwu r1, -8(r1) /* Save back chain and move SP */ - stw r0, +12(r1) /* Save return addr (underflow vect) */ -#endif /* !(CFG_INIT_DCACHE_CS || !CFG_TEM_STACK_OCM) */ - #ifdef CONFIG_NAND_SPL bl nand_boot /* will not return */ #else @@ -1273,7 +1282,7 @@ icache_enable: bl invalidate_icache mtlr r8 isync - addis r3,r0, 0x8000 /* set bit 0 */ + addis r3,r0, 0xc000 /* set bit 0 */ mticcr r3 blr diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h index bddf9e5daa9..93e51b90ccd 100644 --- a/cpu/ppc4xx/vecnum.h +++ b/cpu/ppc4xx/vecnum.h @@ -270,6 +270,110 @@ #define VECNUM_EIR3 30 /* External interrupt 3 */ #define VECNUM_EIR4 31 /* External interrupt 4 */ +#elif defined(CONFIG_405EX) + +/* UIC 0 */ +#define VECNUM_U0 00 +#define VECNUM_U1 01 +#define VECNUM_IIC0 02 +#define VECNUM_PKA 03 +#define VECNUM_TRNG 04 +#define VECNUM_EBM 05 +#define VECNUM_BGI 06 +#define VECNUM_IIC1 07 +#define VECNUM_SPI 08 +#define VECNUM_EIR0 09 +#define VECNUM_MTE 10 /* MAL Tx EOB */ +#define VECNUM_MRE 11 /* MAL Rx EOB */ +#define VECNUM_DMA0 12 +#define VECNUM_DMA1 13 +#define VECNUM_DMA2 14 +#define VECNUM_DMA3 15 +#define VECNUM_PCIE0AL 16 +#define VECNUM_PCIE0VPD 17 +#define VECNUM_RPCIE0HRST 18 +#define VECNUM_FPCIE0HRST 19 +#define VECNUM_PCIE0TCR 20 +#define VECNUM_PCIEMSI0 21 +#define VECNUM_PCIEMSI1 22 +#define VECNUM_SECURITY 23 +#define VECNUM_ETH0 24 +#define VECNUM_ETH1 25 +#define VECNUM_PCIEMSI2 26 +#define VECNUM_EIR4 27 +#define VECNUM_UIC2NC 28 +#define VECNUM_UIC2C 29 +#define VECNUM_UIC1NC 30 +#define VECNUM_UIC1C 31 + +/* UIC 1 */ +#define VECNUM_MS (32 + 00) /* MAL SERR */ +#define VECNUM_TXDE (32 + 01) /* MAL TXDE */ +#define VECNUM_RXDE (32 + 02) /* MAL RXDE */ +#define VECNUM_PCIE0BMVC0 (32 + 03) +#define VECNUM_PCIE0DCRERR (32 + 04) +#define VECNUM_EBC (32 + 05) +#define VECNUM_NDFC (32 + 06) +#define VECNUM_PCEI1DCRERR (32 + 07) +#define VECNUM_CT8 (32 + 08) +#define VECNUM_CT9 (32 + 09) +#define VECNUM_PCIE1AL (32 + 10) +#define VECNUM_PCIE1VPD (32 + 11) +#define VECNUM_RPCE1HRST (32 + 12) +#define VECNUM_FPCE1HRST (32 + 13) +#define VECNUM_PCIE1TCR (32 + 14) +#define VECNUM_PCIE1VC0 (32 + 15) +#define VECNUM_CT3 (32 + 16) +#define VECNUM_CT4 (32 + 17) +#define VECNUM_EIR7 (32 + 18) +#define VECNUM_EIR8 (32 + 19) +#define VECNUM_EIR9 (32 + 20) +#define VECNUM_CT5 (32 + 21) +#define VECNUM_CT6 (32 + 22) +#define VECNUM_CT7 (32 + 23) +#define VECNUM_SROM (32 + 24) /* SERIAL ROM */ +#define VECNUM_GPTDECPULS (32 + 25) /* GPT Decrement pulse */ +#define VECNUM_EIR2 (32 + 26) +#define VECNUM_EIR5 (32 + 27) +#define VECNUM_EIR6 (32 + 28) +#define VECNUM_EMAC0WAKE (32 + 29) +#define VECNUM_EIR1 (32 + 30) +#define VECNUM_EMAC1WAKE (32 + 31) + +/* UIC 2 */ +#define VECNUM_PCIE0INTA (64 + 00) /* PCIE0 INTA */ +#define VECNUM_PCIE0INTB (64 + 01) /* PCIE0 INTB */ +#define VECNUM_PCIE0INTC (64 + 02) /* PCIE0 INTC */ +#define VECNUM_PCIE0INTD (64 + 03) /* PCIE0 INTD */ +#define VECNUM_EIR3 (64 + 04) /* External IRQ 3 */ +#define VECNUM_DDRMCUE (64 + 05) +#define VECNUM_DDRMCCE (64 + 06) +#define VECNUM_MALINTCOATX0 (64 + 07) /* Interrupt coalecence TX0 */ +#define VECNUM_MALINTCOATX1 (64 + 08) /* Interrupt coalecence TX1 */ +#define VECNUM_MALINTCOARX0 (64 + 09) /* Interrupt coalecence RX0 */ +#define VECNUM_MALINTCOARX1 (64 + 10) /* Interrupt coalecence RX1 */ +#define VECNUM_PCIE1INTA (64 + 11) /* PCIE0 INTA */ +#define VECNUM_PCIE1INTB (64 + 12) /* PCIE0 INTB */ +#define VECNUM_PCIE1INTC (64 + 13) /* PCIE0 INTC */ +#define VECNUM_PCIE1INTD (64 + 14) /* PCIE0 INTD */ +#define VECNUM_RPCIEMSI2 (64 + 15) /* MSI level 2 */ +#define VECNUM_PCIEMSI3 (64 + 16) /* MSI level 2 */ +#define VECNUM_PCIEMSI4 (64 + 17) /* MSI level 2 */ +#define VECNUM_PCIEMSI5 (64 + 18) /* MSI level 2 */ +#define VECNUM_PCIEMSI6 (64 + 19) /* MSI level 2 */ +#define VECNUM_PCIEMSI7 (64 + 20) /* MSI level 2 */ +#define VECNUM_PCIEMSI8 (64 + 21) /* MSI level 2 */ +#define VECNUM_PCIEMSI9 (64 + 22) /* MSI level 2 */ +#define VECNUM_PCIEMSI10 (64 + 23) /* MSI level 2 */ +#define VECNUM_PCIEMSI11 (64 + 24) /* MSI level 2 */ +#define VECNUM_PCIEMSI12 (64 + 25) /* MSI level 2 */ +#define VECNUM_PCIEMSI13 (64 + 26) /* MSI level 2 */ +#define VECNUM_PCIEMSI14 (64 + 27) /* MSI level 2 */ +#define VECNUM_PCIEMSI15 (64 + 28) /* MSI level 2 */ +#define VECNUM_PLB4XAHB (64 + 29) /* PLBxAHB bridge */ +#define VECNUM_USBWAKE (64 + 30) /* USB wakup */ +#define VECNUM_USBOTG (64 + 31) /* USB OTG */ + #else /* !CONFIG_405EZ */ #define VECNUM_U0 0 /* UART0 */ diff --git a/include/405_mal.h b/include/405_mal.h index 2a421848b4b..7ea4eb1cc48 100644 --- a/include/405_mal.h +++ b/include/405_mal.h @@ -92,7 +92,9 @@ #define MAL_ESR_PBEI 0x00000001 /* ^^ ^^ */ /* Mal IER */ -#if defined(CONFIG_440SPE) || defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440SPE) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define MAL_IER_PT 0x00000080 #define MAL_IER_PRE 0x00000040 #define MAL_IER_PWE 0x00000020 diff --git a/include/4xx_i2c.h b/include/4xx_i2c.h index 66b7997419b..7c79bd153ec 100644 --- a/include/4xx_i2c.h +++ b/include/4xx_i2c.h @@ -43,7 +43,7 @@ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000700 + I2C_BUS_OFFS) -#elif defined(CONFIG_440) +#elif defined(CONFIG_440) || defined(CONFIG_405EX) /* all remaining 440 variants */ #define I2C_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x00000400 + I2C_BUS_OFFS) #else diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 0a160e2513a..451ee94f618 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -765,6 +765,10 @@ #define PVR_405EP_RA 0x51210950 #define PVR_405GPR_RB 0x50910951 #define PVR_405EZ_RA 0x41511460 +#define PVR_405EXR1_RA 0x12911473 /* 405EXr rev A with Security */ +#define PVR_405EXR2_RA 0x12911471 /* 405EXr rev A without Security */ +#define PVR_405EX1_RA 0x12911477 /* 405EX rev A with Security */ +#define PVR_405EX2_RA 0x12911475 /* 405EX rev A without Security */ #define PVR_440GP_RB 0x40120440 #define PVR_440GP_RC 0x40120481 #define PVR_440EP_RA 0x42221850 diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h index 464f6b5756e..bd9b6f70dda 100644 --- a/include/asm-ppc/u-boot.h +++ b/include/asm-ppc/u-boot.h @@ -84,6 +84,7 @@ typedef struct bd_info { defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || \ defined(CONFIG_405EZ) || \ + defined(CONFIG_405EX) || \ defined(CONFIG_440) unsigned char bi_s_version[4]; /* Version of this structure */ unsigned char bi_r_version[32]; /* Version of the ROM (AMCC) */ diff --git a/include/common.h b/include/common.h index aca281bdad6..98655914f72 100644 --- a/include/common.h +++ b/include/common.h @@ -266,7 +266,7 @@ void pciinfo (int, int); int pci_pre_init (struct pci_controller * ); #endif -#if defined(CONFIG_PCI) && defined(CONFIG_440) +#if defined(CONFIG_PCI) && (defined(CONFIG_440) || defined(CONFIG_405EX)) # if defined(CFG_PCI_TARGET_INIT) void pci_target_init (struct pci_controller *); # endif @@ -274,7 +274,7 @@ void pciinfo (int, int); void pci_master_init (struct pci_controller *); # endif int is_pci_host (struct pci_controller *); -#if defined(CONFIG_440SPE) +#if defined(CONFIG_440SPE) || defined(CONFIG_405EX) void pcie_setup_hoses(int busno); #endif #endif diff --git a/include/ppc405.h b/include/ppc405.h index 0c7bf3e6def..82bc25e1f41 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -123,6 +123,40 @@ #define uicvr (UIC_DCR_BASE+0x7) /* UIC vector */ #define uicvcr (UIC_DCR_BASE+0x8) /* UIC vector configuration */ +#if defined(CONFIG_405EX) +#define uic0sr uicsr /* UIC status */ +#define uic0srs uicsrs /* UIC status set */ +#define uic0er uicer /* UIC enable */ +#define uic0cr uiccr /* UIC critical */ +#define uic0pr uicpr /* UIC polarity */ +#define uic0tr uictr /* UIC triggering */ +#define uic0msr uicmsr /* UIC masked status */ +#define uic0vr uicvr /* UIC vector */ +#define uic0vcr uicvcr /* UIC vector configuration*/ + +#define UIC_DCR_BASE1 0xd0 +#define uic1sr (UIC_DCR_BASE1+0x0) /* UIC status */ +#define uic1srs (UIC_DCR_BASE1+0x1) /* UIC status set */ +#define uic1er (UIC_DCR_BASE1+0x2) /* UIC enable */ +#define uic1cr (UIC_DCR_BASE1+0x3) /* UIC critical */ +#define uic1pr (UIC_DCR_BASE1+0x4) /* UIC polarity */ +#define uic1tr (UIC_DCR_BASE1+0x5) /* UIC triggering */ +#define uic1msr (UIC_DCR_BASE1+0x6) /* UIC masked status */ +#define uic1vr (UIC_DCR_BASE1+0x7) /* UIC vector */ +#define uic1vcr (UIC_DCR_BASE1+0x8) /* UIC vector configuration*/ + +#define UIC_DCR_BASE2 0xe0 +#define uic2sr (UIC_DCR_BASE2+0x0) /* UIC status */ +#define uic2srs (UIC_DCR_BASE2+0x1) /* UIC status set */ +#define uic2er (UIC_DCR_BASE2+0x2) /* UIC enable */ +#define uic2cr (UIC_DCR_BASE2+0x3) /* UIC critical */ +#define uic2pr (UIC_DCR_BASE2+0x4) /* UIC polarity */ +#define uic2tr (UIC_DCR_BASE2+0x5) /* UIC triggering */ +#define uic2msr (UIC_DCR_BASE2+0x6) /* UIC masked status */ +#define uic2vr (UIC_DCR_BASE2+0x7) /* UIC vector */ +#define uic2vcr (UIC_DCR_BASE2+0x8) /* UIC vector configuration*/ +#endif + /*-----------------------------------------------------------------------------+ | Universal interrupt controller interrupts +-----------------------------------------------------------------------------*/ @@ -166,6 +200,116 @@ #define UIC_EXT3 0x00000002 /* External interrupt 3 */ #define UIC_EXT4 0x00000001 /* External interrupt 4 */ +#elif defined(CONFIG_405EX) + +/* UIC 0 */ +#define UIC_U0 0x80000000 /* */ +#define UIC_U1 0x40000000 /* */ +#define UIC_IIC0 0x20000000 /* */ +#define UIC_PKA 0x10000000 /* */ +#define UIC_TRNG 0x08000000 /* */ +#define UIC_EBM 0x04000000 /* */ +#define UIC_BGI 0x02000000 /* */ +#define UIC_IIC1 0x01000000 /* */ +#define UIC_SPI 0x00800000 /* */ +#define UIC_EIRQ0 0x00400000 /**/ +#define UIC_MTE 0x00200000 /*MAL Tx EOB */ +#define UIC_MRE 0x00100000 /*MAL Rx EOB */ +#define UIC_DMA0 0x00080000 /* */ +#define UIC_DMA1 0x00040000 /* */ +#define UIC_DMA2 0x00020000 /* */ +#define UIC_DMA3 0x00010000 /* */ +#define UIC_PCIE0AL 0x00008000 /* */ +#define UIC_PCIE0VPD 0x00004000 /* */ +#define UIC_RPCIE0HRST 0x00002000 /* */ +#define UIC_FPCIE0HRST 0x00001000 /* */ +#define UIC_PCIE0TCR 0x00000800 /* */ +#define UIC_PCIEMSI0 0x00000400 /* */ +#define UIC_PCIEMSI1 0x00000200 /* */ +#define UIC_SECURITY 0x00000100 /* */ +#define UIC_ENET 0x00000080 /* */ +#define UIC_ENET1 0x00000040 /* */ +#define UIC_PCIEMSI2 0x00000020 /* */ +#define UIC_EIRQ4 0x00000010 /**/ +#define UIC_UIC2NC 0x00000008 /* */ +#define UIC_UIC2C 0x00000004 /* */ +#define UIC_UIC1NC 0x00000002 /* */ +#define UIC_UIC1C 0x00000001 /* */ + +#define UIC_MAL_TXEOB UIC_MTE/* MAL TXEOB */ +#define UIC_MAL_RXEOB UIC_MRE/* MAL RXEOB */ +/* UIC 1 */ +#define UIC_MS 0x80000000 /* MAL SERR */ +#define UIC_MTDE 0x40000000 /* MAL TXDE */ +#define UIC_MRDE 0x20000000 /* MAL RXDE */ +#define UIC_PCIE0BMVC0 0x10000000 /* */ +#define UIC_PCIE0DCRERR 0x08000000 /* */ +#define UIC_EBC 0x04000000 /* */ +#define UIC_NDFC 0x02000000 /* */ +#define UIC_PCEI1DCRERR 0x01000000 /* */ +#define UIC_GPTCMPT8 0x00800000 /* */ +#define UIC_GPTCMPT9 0x00400000 /* */ +#define UIC_PCIE1AL 0x00200000 /* */ +#define UIC_PCIE1VPD 0x00100000 /* */ +#define UIC_RPCE1HRST 0x00080000 /* */ +#define UIC_FPCE1HRST 0x00040000 /* */ +#define UIC_PCIE1TCR 0x00020000 /* */ +#define UIC_PCIE1VC0 0x00010000 /* */ +#define UIC_GPTCMPT3 0x00008000 /* */ +#define UIC_GPTCMPT4 0x00004000 /* */ +#define UIC_EIRQ7 0x00002000 /* */ +#define UIC_EIRQ8 0x00001000 /* */ +#define UIC_EIRQ9 0x00000800 /* */ +#define UIC_GPTCMP5 0x00000400 /* */ +#define UIC_GPTCMP6 0x00000200 /* */ +#define UIC_GPTCMP7 0x00000100 /* */ +#define UIC_SROM 0x00000080 /* SERIAL ROM*/ +#define UIC_GPTDECPULS 0x00000040 /* GPT Decrement pulse*/ +#define UIC_EIRQ2 0x00000020 /* */ +#define UIC_EIRQ5 0x00000010 /* */ +#define UIC_EIRQ6 0x00000008 /* */ +#define UIC_EMAC0WAKE 0x00000004 /* */ +#define UIC_EIRQ1 0x00000002 /* */ +#define UIC_EMAC1WAKE 0x00000001 /* */ +#define UIC_MAL_SERR UIC_MS /* MAL SERR */ +#define UIC_MAL_TXDE UIC_MTDE /* MAL TXDE */ +#define UIC_MAL_RXDE UIC_MRDE /* MAL RXDE */ +/* UIC 2 */ +#define UIC_PCIE0INTA 0x80000000 /* PCIE0 INTA*/ +#define UIC_PCIE0INTB 0x40000000 /* PCIE0 INTB*/ +#define UIC_PCIE0INTC 0x20000000 /* PCIE0 INTC*/ +#define UIC_PCIE0INTD 0x10000000 /* PCIE0 INTD*/ +#define UIC_EIRQ3 0x08000000 /* External IRQ 3*/ +#define UIC_DDRMCUE 0x04000000 /* */ +#define UIC_DDRMCCE 0x02000000 /* */ +#define UIC_MALINTCOATX0 0x01000000 /* Interrupt coalecence TX0*/ +#define UIC_MALINTCOATX1 0x00800000 /* Interrupt coalecence TX1*/ +#define UIC_MALINTCOARX0 0x00400000 /* Interrupt coalecence RX0*/ +#define UIC_MALINTCOARX1 0x00200000 /* Interrupt coalecence RX1*/ +#define UIC_PCIE1INTA 0x00100000 /* PCIE0 INTA*/ +#define UIC_PCIE1INTB 0x00080000 /* PCIE0 INTB*/ +#define UIC_PCIE1INTC 0x00040000 /* PCIE0 INTC*/ +#define UIC_PCIE1INTD 0x00020000 /* PCIE0 INTD*/ +#define UIC_RPCIEMSI2 0x00010000 /* MSI level 2 Note this looks same as uic0-26*/ +#define UIC_PCIEMSI3 0x00008000 /* MSI level 2*/ +#define UIC_PCIEMSI4 0x00004000 /* MSI level 2*/ +#define UIC_PCIEMSI5 0x00002000 /* MSI level 2*/ +#define UIC_PCIEMSI6 0x00001000 /* MSI level 2*/ +#define UIC_PCIEMSI7 0x00000800 /* MSI level 2*/ +#define UIC_PCIEMSI8 0x00000400 /* MSI level 2*/ +#define UIC_PCIEMSI9 0x00000200 /* MSI level 2*/ +#define UIC_PCIEMSI10 0x00000100 /* MSI level 2*/ +#define UIC_PCIEMSI11 0x00000080 /* MSI level 2*/ +#define UIC_PCIEMSI12 0x00000040 /* MSI level 2*/ +#define UIC_PCIEMSI13 0x00000020 /* MSI level 2*/ +#define UIC_PCIEMSI14 0x00000010 /* MSI level 2*/ +#define UIC_PCIEMSI15 0x00000008 /* MSI level 2*/ +#define UIC_PLB4XAHB 0x00000004 /* PLBxAHB bridge*/ +#define UIC_USBWAKE 0x00000002 /* USB wakup*/ +#define UIC_USBOTG 0x00000001 /* USB OTG*/ +#define UIC_ETH0 UIC_ENET +#define UIC_ETH1 UIC_ENET1 + #else /* !defined(CONFIG_405EZ) */ #define UIC_UART0 0x80000000 /* UART 0 */ @@ -256,7 +400,11 @@ /****************************************************************************** * Power Management ******************************************************************************/ +#ifdef CONFIG_405EX +#define POWERMAN_DCR_BASE 0xb0 +#else #define POWERMAN_DCR_BASE 0xb8 +#endif #define cpmsr (POWERMAN_DCR_BASE+0x0) /* Power management status */ #define cpmer (POWERMAN_DCR_BASE+0x1) /* Power management enable */ #define cpmfr (POWERMAN_DCR_BASE+0x2) /* Power management force */ @@ -561,16 +709,6 @@ #define VCO_MIN 500 #define VCO_MAX 1000 #elif defined(CONFIG_405EZ) -/****************************************************************************** - * SDR Registers - ******************************************************************************/ -#define SDR_DCR_BASE 0x0E -#define sdrcfga (SDR_DCR_BASE+0x0) /* ADDR */ -#define sdrcfgd (SDR_DCR_BASE+0x1) /* Data */ - -#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0) -#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0) - #define sdrnand0 0x4000 #define sdrultra0 0x4040 #define sdrultra1 0x4050 @@ -1214,6 +1352,25 @@ #define GPIO1_ISR3L (GPIO1_BASE+0x40) #define GPIO1_ISR3H (GPIO1_BASE+0x44) +#elif defined(CONFIG_405EX) +#define GPIO_BASE 0xEF600800 +#define GPIO0_OR (GPIO_BASE+0x0) +#define GPIO0_TCR (GPIO_BASE+0x4) +#define GPIO0_OSRL (GPIO_BASE+0x8) +#define GPIO0_OSRH (GPIO_BASE+0xC) +#define GPIO0_TSRL (GPIO_BASE+0x10) +#define GPIO0_TSRH (GPIO_BASE+0x14) +#define GPIO0_ODR (GPIO_BASE+0x18) +#define GPIO0_IR (GPIO_BASE+0x1C) +#define GPIO0_RR1 (GPIO_BASE+0x20) +#define GPIO0_RR2 (GPIO_BASE+0x24) +#define GPIO0_ISR1L (GPIO_BASE+0x30) +#define GPIO0_ISR1H (GPIO_BASE+0x34) +#define GPIO0_ISR2L (GPIO_BASE+0x38) +#define GPIO0_ISR2H (GPIO_BASE+0x3C) +#define GPIO0_ISR3L (GPIO_BASE+0x40) +#define GPIO0_ISR3H (GPIO_BASE+0x44) + #else /* !405EZ */ #define GPIO_BASE 0xEF600700 @@ -1234,33 +1391,489 @@ #endif /* CONFIG_405EZ */ -/* - * Macro for accessing the indirect EBC register - */ -#define mtebc(reg, data) mtdcr(ebccfga,reg);mtdcr(ebccfgd,data) -#define mfebc(reg, data) mtdcr(ebccfga,reg);data = mfdcr(ebccfgd) +#if defined(CONFIG_405EX) +#define SDR0_SRST 0x0200 + +#define SDRAM_BESR0 0x00 +#define SDRAM_BEARL 0x02 +#define SDRAM_BEARU 0x03 +#define SDRAM_WMIRQ 0x06 /**/ +#define SDRAM_PLBOPT 0x08 /**/ +#define SDRAM_PUABA 0x09 /**/ +#define SDRAM_MCSTAT 0x1F /* memory controller status */ +#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */ +#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */ +#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */ +#define SDRAM_MODT1 0x23 /* on die termination for bank 1 */ +#define SDRAM_MODT2 0x24 /* on die termination for bank 2 */ +#define SDRAM_MODT3 0x25 /* on die termination for bank 3 */ +#define SDRAM_CODT 0x26 /* on die termination for controller */ +#define SDRAM_VVPR 0x27 /* variable VRef programmming */ +#define SDRAM_OPARS 0x28 /* on chip driver control setup */ +#define SDRAM_OPART 0x29 /* on chip driver control trigger */ +#define SDRAM_RTR 0x30 /* refresh timer */ +#define SDRAM_PMIT 0x34 /* power management idle timer */ +#define SDRAM_MB0CF 0x40 /* memory bank 0 configuration */ +#define SDRAM_MB1CF 0x44 /* memory bank 1 configuration */ +#define SDRAM_MB2CF 0x48 /* memory bank 2 configuration */ +#define SDRAM_MB3CF 0x4C /* memory bank 3 configuration */ +#define SDRAM_INITPLR0 0x50 /* manual initialization control */ +#define SDRAM_INITPLR1 0x51 /* manual initialization control */ +#define SDRAM_INITPLR2 0x52 /* manual initialization control */ +#define SDRAM_INITPLR3 0x53 /* manual initialization control */ +#define SDRAM_INITPLR4 0x54 /* manual initialization control */ +#define SDRAM_INITPLR5 0x55 /* manual initialization control */ +#define SDRAM_INITPLR6 0x56 /* manual initialization control */ +#define SDRAM_INITPLR7 0x57 /* manual initialization control */ +#define SDRAM_INITPLR8 0x58 /* manual initialization control */ +#define SDRAM_INITPLR9 0x59 /* manual initialization control */ +#define SDRAM_INITPLR10 0x5a /* manual initialization control */ +#define SDRAM_INITPLR11 0x5b /* manual initialization control */ +#define SDRAM_INITPLR12 0x5c /* manual initialization control */ +#define SDRAM_INITPLR13 0x5d /* manual initialization control */ +#define SDRAM_INITPLR14 0x5e /* manual initialization control */ +#define SDRAM_INITPLR15 0x5f /* manual initialization control */ +#define SDRAM_RQDC 0x70 /* read DQS delay control */ +#define SDRAM_RFDC 0x74 /* read feedback delay control */ +#define SDRAM_RDCC 0x78 /* read data capture control */ +#define SDRAM_DLCR 0x7A /* delay line calibration */ +#define SDRAM_CLKTR 0x80 /* DDR clock timing */ +#define SDRAM_WRDTR 0x81 /* write data, DQS, DM clock, timing */ +#define SDRAM_SDTR1 0x85 /* DDR SDRAM timing 1 */ +#define SDRAM_SDTR2 0x86 /* DDR SDRAM timing 2 */ +#define SDRAM_SDTR3 0x87 /* DDR SDRAM timing 3 */ +#define SDRAM_MMODE 0x88 /* memory mode */ +#define SDRAM_MEMODE 0x89 /* memory extended mode */ +#define SDRAM_ECCCR 0x98 /* ECC error status */ +#define SDRAM_RID 0xF8 /* revision ID */ + +/*-----------------------------------------------------------------------------+ +| Memory Bank 0-7 configuration ++-----------------------------------------------------------------------------*/ +#define SDRAM_RXBAS_SDSZ_4 0x00000000 /* 4M */ +#define SDRAM_RXBAS_SDSZ_8 0x00001000 /* 8M */ +#define SDRAM_RXBAS_SDSZ_16 0x00002000 /* 16M */ +#define SDRAM_RXBAS_SDSZ_32 0x00003000 /* 32M */ +#define SDRAM_RXBAS_SDSZ_64 0x00004000 /* 64M */ +#define SDRAM_RXBAS_SDSZ_128 0x00005000 /* 128M */ +#define SDRAM_RXBAS_SDSZ_256 0x00006000 /* 256M */ +#define SDRAM_RXBAS_SDSZ_512 0x00007000 /* 512M */ +#define SDRAM_RXBAS_SDSZ_1024 0x00008000 /* 1024M */ +#define SDRAM_RXBAS_SDSZ_2048 0x00009000 /* 2048M */ +#define SDRAM_RXBAS_SDSZ_4096 0x0000a000 /* 4096M */ +#define SDRAM_RXBAS_SDSZ_8192 0x0000b000 /* 8192M */ + +/*-----------------------------------------------------------------------------+ +| Memory Controller Status ++-----------------------------------------------------------------------------*/ +#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */ +#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */ +#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */ +#define SDRAM_MCSTAT_SRMS_MASK 0x80000000 /* Mem self refresh stat mask */ +#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */ +#define SDRAM_MCSTAT_SRMS_SF 0x80000000 /* Mem in self refresh */ + +/*-----------------------------------------------------------------------------+ +| Memory Controller Options 1 ++-----------------------------------------------------------------------------*/ +#define SDRAM_MCOPT1_MCHK_MASK 0x30000000 /* Memory data err check mask */ +#define SDRAM_MCOPT1_MCHK_NON 0x00000000 /* No ECC generation */ +#define SDRAM_MCOPT1_MCHK_GEN 0x20000000 /* ECC generation */ +#define SDRAM_MCOPT1_MCHK_CHK 0x10000000 /* ECC generation and check */ +#define SDRAM_MCOPT1_MCHK_CHK_REP 0x30000000 /* ECC generation, chk, report*/ +#define SDRAM_MCOPT1_MCHK_CHK_DECODE(n) ((((unsigned long)(n))>>28)&0x3) +#define SDRAM_MCOPT1_RDEN_MASK 0x08000000 /* Registered DIMM mask */ +#define SDRAM_MCOPT1_RDEN 0x08000000 /* Registered DIMM enable */ +#define SDRAM_MCOPT1_PMU_MASK 0x06000000 /* Page management unit mask */ +#define SDRAM_MCOPT1_PMU_CLOSE 0x00000000 /* PMU Close */ +#define SDRAM_MCOPT1_PMU_OPEN 0x04000000 /* PMU Open */ +#define SDRAM_MCOPT1_PMU_AUTOCLOSE 0x02000000 /* PMU AutoClose */ +#define SDRAM_MCOPT1_DMWD_MASK 0x01000000 /* DRAM width mask */ +#define SDRAM_MCOPT1_DMWD_32 0x00000000 /* 32 bits */ +#define SDRAM_MCOPT1_DMWD_64 0x01000000 /* 64 bits */ +#define SDRAM_MCOPT1_UIOS_MASK 0x00C00000 /* Unused IO State */ +#define SDRAM_MCOPT1_BCNT_MASK 0x00200000 /* Bank count */ +#define SDRAM_MCOPT1_4_BANKS 0x00000000 /* 4 Banks */ +#define SDRAM_MCOPT1_8_BANKS 0x00200000 /* 8 Banks */ +#define SDRAM_MCOPT1_DDR_TYPE_MASK 0x00100000 /* DDR Memory Type mask */ +#define SDRAM_MCOPT1_DDR1_TYPE 0x00000000 /* DDR1 Memory Type */ +#define SDRAM_MCOPT1_DDR2_TYPE 0x00100000 /* DDR2 Memory Type */ +#define SDRAM_MCOPT1_QDEP 0x00020000 /* 4 commands deep */ +#define SDRAM_MCOPT1_RWOO_MASK 0x00008000 /* Out of Order Read mask */ +#define SDRAM_MCOPT1_RWOO_DISABLED 0x00000000 /* disabled */ +#define SDRAM_MCOPT1_RWOO_ENABLED 0x00008000 /* enabled */ +#define SDRAM_MCOPT1_WOOO_MASK 0x00004000 /* Out of Order Write mask */ +#define SDRAM_MCOPT1_WOOO_DISABLED 0x00000000 /* disabled */ +#define SDRAM_MCOPT1_WOOO_ENABLED 0x00004000 /* enabled */ +#define SDRAM_MCOPT1_DCOO_MASK 0x00002000 /* All Out of Order mask */ +#define SDRAM_MCOPT1_DCOO_DISABLED 0x00002000 /* disabled */ +#define SDRAM_MCOPT1_DCOO_ENABLED 0x00000000 /* enabled */ +#define SDRAM_MCOPT1_DREF_MASK 0x00001000 /* Deferred refresh mask */ +#define SDRAM_MCOPT1_DREF_NORMAL 0x00000000 /* normal refresh */ +#define SDRAM_MCOPT1_DREF_DEFER_4 0x00001000 /* defer up to 4 refresh cmd */ + +/*-----------------------------------------------------------------------------+ +| Memory Controller Options 2 ++-----------------------------------------------------------------------------*/ +#define SDRAM_MCOPT2_SREN_MASK 0x80000000 /* Self Test mask */ +#define SDRAM_MCOPT2_SREN_EXIT 0x00000000 /* Self Test exit */ +#define SDRAM_MCOPT2_SREN_ENTER 0x80000000 /* Self Test enter */ +#define SDRAM_MCOPT2_PMEN_MASK 0x40000000 /* Power Management mask */ +#define SDRAM_MCOPT2_PMEN_DISABLE 0x00000000 /* disable */ +#define SDRAM_MCOPT2_PMEN_ENABLE 0x40000000 /* enable */ +#define SDRAM_MCOPT2_IPTR_MASK 0x20000000 /* Init Trigger Reg mask */ +#define SDRAM_MCOPT2_IPTR_IDLE 0x00000000 /* idle */ +#define SDRAM_MCOPT2_IPTR_EXECUTE 0x20000000 /* execute preloaded init */ +#define SDRAM_MCOPT2_XSRP_MASK 0x10000000 /* Exit Self Refresh Prevent */ +#define SDRAM_MCOPT2_XSRP_ALLOW 0x00000000 /* allow self refresh exit */ +#define SDRAM_MCOPT2_XSRP_PREVENT 0x10000000 /* prevent self refresh exit */ +#define SDRAM_MCOPT2_DCEN_MASK 0x08000000 /* SDRAM Controller Enable */ +#define SDRAM_MCOPT2_DCEN_DISABLE 0x00000000 /* SDRAM Controller Enable */ +#define SDRAM_MCOPT2_DCEN_ENABLE 0x08000000 /* SDRAM Controller Enable */ +#define SDRAM_MCOPT2_ISIE_MASK 0x04000000 /* Init Seq Interruptable mas*/ +#define SDRAM_MCOPT2_ISIE_DISABLE 0x00000000 /* disable */ +#define SDRAM_MCOPT2_ISIE_ENABLE 0x04000000 /* enable */ + +/*-----------------------------------------------------------------------------+ +| SDRAM Refresh Timer Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_RTR_RINT_MASK 0xFFF80000 +#define SDRAM_RTR_RINT_ENCODE(n) ((((unsigned long)(n))&0xFFF8)<<16) +#define SDRAM_RTR_RINT_DECODE(n) ((((unsigned long)(n))>>16)&0xFFF8) + +/*-----------------------------------------------------------------------------+ +| SDRAM Read DQS Delay Control Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_RQDC_RQDE_MASK 0x80000000 +#define SDRAM_RQDC_RQDE_DISABLE 0x00000000 +#define SDRAM_RQDC_RQDE_ENABLE 0x80000000 +#define SDRAM_RQDC_RQFD_MASK 0x000001FF +#define SDRAM_RQDC_RQFD_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0) + +#define SDRAM_RQDC_RQFD_MAX 0xFF + +/*-----------------------------------------------------------------------------+ +| SDRAM Read Data Capture Control Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_RDCC_RDSS_MASK 0xC0000000 +#define SDRAM_RDCC_RDSS_T1 0x00000000 +#define SDRAM_RDCC_RDSS_T2 0x40000000 +#define SDRAM_RDCC_RDSS_T3 0x80000000 +#define SDRAM_RDCC_RDSS_T4 0xC0000000 +#define SDRAM_RDCC_RSAE_MASK 0x00000001 +#define SDRAM_RDCC_RSAE_DISABLE 0x00000001 +#define SDRAM_RDCC_RSAE_ENABLE 0x00000000 + +/*-----------------------------------------------------------------------------+ +| SDRAM Read Feedback Delay Control Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_RFDC_ARSE_MASK 0x80000000 +#define SDRAM_RFDC_ARSE_DISABLE 0x80000000 +#define SDRAM_RFDC_ARSE_ENABLE 0x00000000 +#define SDRAM_RFDC_RFOS_MASK 0x007F0000 +#define SDRAM_RFDC_RFOS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define SDRAM_RFDC_RFFD_MASK 0x000003FF +#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) + +#define SDRAM_RFDC_RFFD_MAX 0x4FF + +/*-----------------------------------------------------------------------------+ +| SDRAM Delay Line Calibration Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_DLCR_DCLM_MASK 0x80000000 +#define SDRAM_DLCR_DCLM_MANUEL 0x80000000 +#define SDRAM_DLCR_DCLM_AUTO 0x00000000 +#define SDRAM_DLCR_DLCR_MASK 0x08000000 +#define SDRAM_DLCR_DLCR_CALIBRATE 0x08000000 +#define SDRAM_DLCR_DLCR_IDLE 0x00000000 +#define SDRAM_DLCR_DLCS_MASK 0x07000000 +#define SDRAM_DLCR_DLCS_NOT_RUN 0x00000000 +#define SDRAM_DLCR_DLCS_IN_PROGRESS 0x01000000 +#define SDRAM_DLCR_DLCS_COMPLETE 0x02000000 +#define SDRAM_DLCR_DLCS_CONT_DONE 0x03000000 +#define SDRAM_DLCR_DLCS_ERROR 0x04000000 +#define SDRAM_DLCR_DLCV_MASK 0x000001FF +#define SDRAM_DLCR_DLCV_ENCODE(n) ((((unsigned long)(n))&0x1FF)<<0) +#define SDRAM_DLCR_DLCV_DECODE(n) ((((unsigned long)(n))>>0)&0x1FF) + +/*-----------------------------------------------------------------------------+ +| SDRAM Controller On Die Termination Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_CODT_ODT_ON 0x80000000 +#define SDRAM_CODT_ODT_OFF 0x00000000 +#define SDRAM_CODT_DQS_VOLTAGE_DDR_MASK 0x00000020 +#define SDRAM_CODT_DQS_2_5_V_DDR1 0x00000000 +#define SDRAM_CODT_DQS_1_8_V_DDR2 0x00000020 +#define SDRAM_CODT_DQS_MASK 0x00000010 +#define SDRAM_CODT_DQS_DIFFERENTIAL 0x00000000 +#define SDRAM_CODT_DQS_SINGLE_END 0x00000010 +#define SDRAM_CODT_CKSE_DIFFERENTIAL 0x00000000 +#define SDRAM_CODT_CKSE_SINGLE_END 0x00000008 +#define SDRAM_CODT_FEEBBACK_RCV_SINGLE_END 0x00000004 +#define SDRAM_CODT_FEEBBACK_DRV_SINGLE_END 0x00000002 +#define SDRAM_CODT_IO_HIZ 0x00000000 +#define SDRAM_CODT_IO_NMODE 0x00000001 + +/*-----------------------------------------------------------------------------+ +| SDRAM Mode Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_MMODE_WR_MASK 0x00000E00 +#define SDRAM_MMODE_WR_DDR1 0x00000000 +#define SDRAM_MMODE_WR_DDR2_3_CYC 0x00000400 +#define SDRAM_MMODE_WR_DDR2_4_CYC 0x00000600 +#define SDRAM_MMODE_WR_DDR2_5_CYC 0x00000800 +#define SDRAM_MMODE_WR_DDR2_6_CYC 0x00000A00 +#define SDRAM_MMODE_DCL_MASK 0x00000070 +#define SDRAM_MMODE_DCL_DDR1_2_0_CLK 0x00000020 +#define SDRAM_MMODE_DCL_DDR1_2_5_CLK 0x00000060 +#define SDRAM_MMODE_DCL_DDR1_3_0_CLK 0x00000030 +#define SDRAM_MMODE_DCL_DDR2_2_0_CLK 0x00000020 +#define SDRAM_MMODE_DCL_DDR2_3_0_CLK 0x00000030 +#define SDRAM_MMODE_DCL_DDR2_4_0_CLK 0x00000040 +#define SDRAM_MMODE_DCL_DDR2_5_0_CLK 0x00000050 +#define SDRAM_MMODE_DCL_DDR2_6_0_CLK 0x00000060 +#define SDRAM_MMODE_DCL_DDR2_7_0_CLK 0x00000070 + +/*-----------------------------------------------------------------------------+ +| SDRAM Extended Mode Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_MEMODE_DIC_MASK 0x00000002 +#define SDRAM_MEMODE_DIC_NORMAL 0x00000000 +#define SDRAM_MEMODE_DIC_WEAK 0x00000002 +#define SDRAM_MEMODE_DLL_MASK 0x00000001 +#define SDRAM_MEMODE_DLL_DISABLE 0x00000001 +#define SDRAM_MEMODE_DLL_ENABLE 0x00000000 +#define SDRAM_MEMODE_RTT_MASK 0x00000044 +#define SDRAM_MEMODE_RTT_DISABLED 0x00000000 +#define SDRAM_MEMODE_RTT_75OHM 0x00000004 +#define SDRAM_MEMODE_RTT_150OHM 0x00000040 +#define SDRAM_MEMODE_DQS_MASK 0x00000400 +#define SDRAM_MEMODE_DQS_DISABLE 0x00000400 +#define SDRAM_MEMODE_DQS_ENABLE 0x00000000 + +/*-----------------------------------------------------------------------------+ +| SDRAM Clock Timing Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_CLKTR_CLKP_MASK 0xC0000000 +#define SDRAM_CLKTR_CLKP_0_DEG 0x00000000 +#define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000 + +/*-----------------------------------------------------------------------------+ +| SDRAM Write Timing Register ++-----------------------------------------------------------------------------*/ +#define SDRAM_WRDTR_WDTP_1_CYC 0x80000000 +#define SDRAM_WRDTR_LLWP_MASK 0x10000000 +#define SDRAM_WRDTR_LLWP_DIS 0x10000000 +#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000 +#define SDRAM_WRDTR_WTR_MASK 0x0E000000 +#define SDRAM_WRDTR_WTR_0_DEG 0x06000000 +#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000 +#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000 + +/*-----------------------------------------------------------------------------+ +| SDRAM SDTR1 Options ++-----------------------------------------------------------------------------*/ +#define SDRAM_SDTR1_LDOF_MASK 0x80000000 +#define SDRAM_SDTR1_LDOF_1_CLK 0x00000000 +#define SDRAM_SDTR1_LDOF_2_CLK 0x80000000 +#define SDRAM_SDTR1_RTW_MASK 0x00F00000 +#define SDRAM_SDTR1_RTW_2_CLK 0x00200000 +#define SDRAM_SDTR1_RTW_3_CLK 0x00300000 +#define SDRAM_SDTR1_WTWO_MASK 0x000F0000 +#define SDRAM_SDTR1_WTWO_0_CLK 0x00000000 +#define SDRAM_SDTR1_WTWO_1_CLK 0x00010000 +#define SDRAM_SDTR1_RTRO_MASK 0x0000F000 +#define SDRAM_SDTR1_RTRO_1_CLK 0x00000000 +#define SDRAM_SDTR1_RTRO_2_CLK 0x00002000 + +/*-----------------------------------------------------------------------------+ +| SDRAM SDTR2 Options ++-----------------------------------------------------------------------------*/ +#define SDRAM_SDTR2_RCD_MASK 0xF0000000 +#define SDRAM_SDTR2_RCD_1_CLK 0x10000000 +#define SDRAM_SDTR2_RCD_2_CLK 0x20000000 +#define SDRAM_SDTR2_RCD_3_CLK 0x30000000 +#define SDRAM_SDTR2_RCD_4_CLK 0x40000000 +#define SDRAM_SDTR2_RCD_5_CLK 0x50000000 +#define SDRAM_SDTR2_WTR_MASK 0x0F000000 +#define SDRAM_SDTR2_WTR_1_CLK 0x01000000 +#define SDRAM_SDTR2_WTR_2_CLK 0x02000000 +#define SDRAM_SDTR2_WTR_3_CLK 0x03000000 +#define SDRAM_SDTR2_WTR_4_CLK 0x04000000 +#define SDRAM_SDTR3_WTR_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) +#define SDRAM_SDTR2_XSNR_MASK 0x00FF0000 +#define SDRAM_SDTR2_XSNR_8_CLK 0x00080000 +#define SDRAM_SDTR2_XSNR_16_CLK 0x00100000 +#define SDRAM_SDTR2_XSNR_32_CLK 0x00200000 +#define SDRAM_SDTR2_XSNR_64_CLK 0x00400000 +#define SDRAM_SDTR2_WPC_MASK 0x0000F000 +#define SDRAM_SDTR2_WPC_2_CLK 0x00002000 +#define SDRAM_SDTR2_WPC_3_CLK 0x00003000 +#define SDRAM_SDTR2_WPC_4_CLK 0x00004000 +#define SDRAM_SDTR2_WPC_5_CLK 0x00005000 +#define SDRAM_SDTR2_WPC_6_CLK 0x00006000 +#define SDRAM_SDTR3_WPC_ENCODE(n) ((((unsigned long)(n))&0xF)<<12) +#define SDRAM_SDTR2_RPC_MASK 0x00000F00 +#define SDRAM_SDTR2_RPC_2_CLK 0x00000200 +#define SDRAM_SDTR2_RPC_3_CLK 0x00000300 +#define SDRAM_SDTR2_RPC_4_CLK 0x00000400 +#define SDRAM_SDTR2_RP_MASK 0x000000F0 +#define SDRAM_SDTR2_RP_3_CLK 0x00000030 +#define SDRAM_SDTR2_RP_4_CLK 0x00000040 +#define SDRAM_SDTR2_RP_5_CLK 0x00000050 +#define SDRAM_SDTR2_RP_6_CLK 0x00000060 +#define SDRAM_SDTR2_RP_7_CLK 0x00000070 +#define SDRAM_SDTR2_RRD_MASK 0x0000000F +#define SDRAM_SDTR2_RRD_2_CLK 0x00000002 +#define SDRAM_SDTR2_RRD_3_CLK 0x00000003 + +/*-----------------------------------------------------------------------------+ +| SDRAM SDTR3 Options ++-----------------------------------------------------------------------------*/ +#define SDRAM_SDTR3_RAS_MASK 0x1F000000 +#define SDRAM_SDTR3_RAS_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define SDRAM_SDTR3_RC_MASK 0x001F0000 +#define SDRAM_SDTR3_RC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16) +#define SDRAM_SDTR3_XCS_MASK 0x00001F00 +#define SDRAM_SDTR3_XCS 0x00000D00 +#define SDRAM_SDTR3_RFC_MASK 0x0000003F +#define SDRAM_SDTR3_RFC_ENCODE(n) ((((unsigned long)(n))&0x3F)<<0) + +/*-----------------------------------------------------------------------------+ +| Memory Bank 0-1 configuration ++-----------------------------------------------------------------------------*/ +#define SDRAM_BXCF_M_AM_MASK 0x00000F00 /* Addressing mode */ +#define SDRAM_BXCF_M_AM_0 0x00000000 /* Mode 0 */ +#define SDRAM_BXCF_M_AM_1 0x00000100 /* Mode 1 */ +#define SDRAM_BXCF_M_AM_2 0x00000200 /* Mode 2 */ +#define SDRAM_BXCF_M_AM_3 0x00000300 /* Mode 3 */ +#define SDRAM_BXCF_M_AM_4 0x00000400 /* Mode 4 */ +#define SDRAM_BXCF_M_AM_5 0x00000500 /* Mode 5 */ +#define SDRAM_BXCF_M_AM_6 0x00000600 /* Mode 6 */ +#define SDRAM_BXCF_M_AM_7 0x00000700 /* Mode 7 */ +#define SDRAM_BXCF_M_AM_8 0x00000800 /* Mode 8 */ +#define SDRAM_BXCF_M_AM_9 0x00000900 /* Mode 9 */ +#define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */ +#define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */ +#define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */ + +#define sdr_uart0 0x0120 /* UART0 Config */ +#define sdr_uart1 0x0121 /* UART1 Config */ +#define sdr_mfr 0x4300 /* SDR0_MFR reg */ + +/* Defines for CPC0_EPRCSR register */ +#define CPC0_EPRCSR_E0NFE 0x80000000 +#define CPC0_EPRCSR_E1NFE 0x40000000 +#define CPC0_EPRCSR_E1RPP 0x00000080 +#define CPC0_EPRCSR_E0RPP 0x00000040 +#define CPC0_EPRCSR_E1ERP 0x00000020 +#define CPC0_EPRCSR_E0ERP 0x00000010 +#define CPC0_EPRCSR_E1PCI 0x00000002 +#define CPC0_EPRCSR_E0PCI 0x00000001 + +#define cpr0_clkupd 0x020 +#define cpr0_pllc 0x040 +#define cpr0_plld 0x060 +#define cpr0_cpud 0x080 +#define cpr0_plbd 0x0a0 +#define cpr0_opbd 0x0c0 +#define cpr0_perd 0x0e0 +#define cpr0_ahbd 0x100 +#define cpr0_icfg 0x140 + +#define SDR_PINSTP 0x0040 +#define sdr_sdcs 0x0060 + +#define SDR0_SDCS_SDD (0x80000000 >> 31) + +/* CUST0 Customer Configuration Register0 */ +#define SDR0_CUST0 0x4000 +#define SDR0_CUST0_MUX_E_N_G_MASK 0xC0000000 /* Mux_Emac_NDFC_GPIO */ +#define SDR0_CUST0_MUX_EMAC_SEL 0x40000000 /* Emac Selection */ +#define SDR0_CUST0_MUX_NDFC_SEL 0x80000000 /* NDFC Selection */ +#define SDR0_CUST0_MUX_GPIO_SEL 0xC0000000 /* GPIO Selection */ + +#define SDR0_CUST0_NDFC_EN_MASK 0x20000000 /* NDFC Enable Mask */ +#define SDR0_CUST0_NDFC_ENABLE 0x20000000 /* NDFC Enable */ +#define SDR0_CUST0_NDFC_DISABLE 0x00000000 /* NDFC Disable */ + +#define SDR0_CUST0_NDFC_BW_MASK 0x10000000 /* NDFC Boot Width */ +#define SDR0_CUST0_NDFC_BW_16_BIT 0x10000000 /* NDFC Boot Width = 16 Bit */ +#define SDR0_CUST0_NDFC_BW_8_BIT 0x00000000 /* NDFC Boot Width = 8 Bit */ + +#define SDR0_CUST0_NDFC_BP_MASK 0x0F000000 /* NDFC Boot Page */ +#define SDR0_CUST0_NDFC_BP_ENCODE(n) ((((unsigned long)(n))&0xF)<<24) +#define SDR0_CUST0_NDFC_BP_DECODE(n) ((((unsigned long)(n))>>24)&0x0F) + +#define SDR0_CUST0_NDFC_BAC_MASK 0x00C00000 /* NDFC Boot Address Cycle */ +#define SDR0_CUST0_NDFC_BAC_ENCODE(n) ((((unsigned long)(n))&0x3)<<22) +#define SDR0_CUST0_NDFC_BAC_DECODE(n) ((((unsigned long)(n))>>22)&0x03) + +#define SDR0_CUST0_NDFC_ARE_MASK 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_ENABLE 0x00200000 /* NDFC Auto Read Enable */ +#define SDR0_CUST0_NDFC_ARE_DISABLE 0x00000000 /* NDFC Auto Read Disable */ + +#define SDR0_CUST0_NRB_MASK 0x00100000 /* NDFC Ready / Busy */ +#define SDR0_CUST0_NRB_BUSY 0x00100000 /* Busy */ +#define SDR0_CUST0_NRB_READY 0x00000000 /* Ready */ + +#define SDR0_CUST0_NDRSC_MASK 0x0000FFF0 /* NDFC Device Reset Count Mask */ +#define SDR0_CUST0_NDRSC_ENCODE(n) ((((unsigned long)(n))&0xFFF)<<4) +#define SDR0_CUST0_NDRSC_DECODE(n) ((((unsigned long)(n))>>4)&0xFFF) + +#define SDR0_CUST0_CHIPSELGAT_MASK 0x0000000F /* Chip Select Gating Mask */ +#define SDR0_CUST0_CHIPSELGAT_DIS 0x00000000 /* Chip Select Gating Disable */ +#define SDR0_CUST0_CHIPSELGAT_ENALL 0x0000000F /* All Chip Select Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN0 0x00000008 /* Chip Select0 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */ +#define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ +#endif + +/****************************************************************************** + * SDR Registers + ******************************************************************************/ +#define SDR_DCR_BASE 0x0E +#define sdrcfga (SDR_DCR_BASE+0x0) +#define sdrcfgd (SDR_DCR_BASE+0x1) + +#define CPR0_DCR_BASE 0x0C +#define cprcfga (CPR0_DCR_BASE+0x0) +#define cprcfgd (CPR0_DCR_BASE+0x1) + +#define mtcpr(reg, d) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,d); } while (0) +#define mfcpr(reg, d) do { mtdcr(cprcfga,reg);d = mfdcr(cprcfgd); } while (0) + +#define mtsdr(reg, d) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,d); } while (0) +#define mfsdr(reg, d) do { mtdcr(sdrcfga,reg);d = mfdcr(sdrcfgd); } while (0) + +#define mtebc(reg, d) do { mtdcr(ebccfga,reg);mtdcr(ebccfgd,d); } while (0) +#define mfebc(reg, d) do { mtdcr(ebccfga,reg);d = mfdcr(ebccfgd); } while (0) -#define mtsdram(reg, data) do { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } while (0) -#define mfsdram(reg, data) do { mtdcr(memcfga,reg);data = mfdcr(memcfgd); } while (0) +#define mtsdram(reg, d) do { mtdcr(memcfga,reg);mtdcr(memcfgd,d); } while (0) +#define mfsdram(reg, d) do { mtdcr(memcfga,reg);d = mfdcr(memcfgd); } while (0) #ifndef __ASSEMBLY__ typedef struct { - unsigned long pllFwdDiv; - unsigned long pllFwdDivB; - unsigned long pllFbkDiv; - unsigned long pllPlbDiv; - unsigned long pllPciDiv; - unsigned long pllExtBusDiv; - unsigned long pllOpbDiv; - unsigned long freqVCOMhz; /* in MHz */ - unsigned long freqProcessor; - unsigned long freqPLB; - unsigned long freqPCI; - unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */ - unsigned long pciClkSync; /* PCI clock is synchronous */ - unsigned long freqVCOHz; + unsigned long pllFwdDiv; + unsigned long pllFwdDivB; + unsigned long pllFbkDiv; + unsigned long pllPlbDiv; + unsigned long pllPciDiv; + unsigned long pllExtBusDiv; + unsigned long pllOpbDiv; + unsigned long freqVCOMhz; /* in MHz */ + unsigned long freqProcessor; + unsigned long freqPLB; + unsigned long freqPCI; + unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */ + unsigned long pciClkSync; /* PCI clock is synchronous */ + unsigned long freqVCOHz; + unsigned long freqOPB; + unsigned long freqEBC; + unsigned long freqDDR; } PPC405_SYS_INFO; #endif /* _ASMLANGUAGE */ diff --git a/include/ppc440.h b/include/ppc440.h index 38809f34b4b..e77c4c3fb66 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -3345,7 +3345,7 @@ typedef struct { unsigned long freqTmrClk; unsigned long freqPLB; unsigned long freqOPB; - unsigned long freqEPB; + unsigned long freqEBC; unsigned long freqPCI; #ifdef CONFIG_440SPE unsigned long freqDDR; diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index 3d8ca090600..76c1d127efb 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -146,11 +146,12 @@ typedef struct emac_4xx_hw_st { #endif #if defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define SDR0_PFC1_EM_1000 (0x00200000) #endif -/*ZMII Bridge Register addresses */ +/* ZMII Bridge Register addresses */ #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define ZMII_BASE (CFG_PERIPHERAL_BASE + 0x0D00) @@ -202,6 +203,8 @@ typedef struct emac_4xx_hw_st { /* RGMII Register Addresses */ #if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x1000) +#elif defined(CONFIG_405EX) +#define RGMII_BASE (CFG_PERIPHERAL_BASE + 0xB00) #else #define RGMII_BASE (CFG_PERIPHERAL_BASE + 0x0790) #endif @@ -223,7 +226,8 @@ typedef struct emac_4xx_hw_st { #define RGMII_SSR_SP_100MBPS (0x02) #define RGMII_SSR_SP_1000MBPS (0x04) -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_405EX) #define RGMII_SSR_V(__x) ((__x) * 8) #else #define RGMII_SSR_V(__x) ((__x -2) * 8) @@ -304,7 +308,7 @@ typedef struct emac_4xx_hw_st { #define EMAC_BASE (CFG_PERIPHERAL_BASE + 0x0800) #endif #else -#if defined(CONFIG_405EZ) +#if defined(CONFIG_405EZ) || defined(CONFIG_405EX) #define EMAC_BASE 0xEF600900 #else #define EMAC_BASE 0xEF600800 @@ -338,7 +342,8 @@ typedef struct emac_4xx_hw_st { /* on 440GX EMAC_MR1 has a different layout! */ #if defined(CONFIG_440GX) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_440SP) || defined(CONFIG_440SPE) + defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_405EX) /* MODE Reg 1 */ #define EMAC_M1_FDE (0x80000000) #define EMAC_M1_ILE (0x40000000) diff --git a/include/serial.h b/include/serial.h index 30bfde3089b..e292f0cd901 100644 --- a/include/serial.h +++ b/include/serial.h @@ -22,8 +22,9 @@ extern struct serial_device serial_smc_device; extern struct serial_device serial_scc_device; extern struct serial_device * default_serial_console (void); -#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \ - || defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_MPC5xxx) +#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) || \ + defined(CONFIG_405EP) || defined(CONFIG_405EZ) || defined(CONFIG_405EX) || \ + defined(CONFIG_MPC5xxx) extern struct serial_device serial0_device; extern struct serial_device serial1_device; #if defined(CFG_NS16550_SERIAL) -- cgit v1.3.1 From 566806ca1a1bf4d895daaf0b2ba5494abbffebaf Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 17:11:30 +0200 Subject: ppc4xx: Add initial AMCC Kilauea 405EX support Signed-off-by: Stefan Roese --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + board/amcc/kilauea/Makefile | 50 +++++ board/amcc/kilauea/cmd_pll.c | 297 ++++++++++++++++++++++++++ board/amcc/kilauea/config.mk | 24 +++ board/amcc/kilauea/init.S | 152 +++++++++++++ board/amcc/kilauea/kilauea.c | 386 +++++++++++++++++++++++++++++++++ board/amcc/kilauea/memory.c | 79 +++++++ board/amcc/kilauea/u-boot.lds | 137 ++++++++++++ include/configs/kilauea.h | 486 ++++++++++++++++++++++++++++++++++++++++++ 11 files changed, 1616 insertions(+) create mode 100644 board/amcc/kilauea/Makefile create mode 100644 board/amcc/kilauea/cmd_pll.c create mode 100644 board/amcc/kilauea/config.mk create mode 100644 board/amcc/kilauea/init.S create mode 100644 board/amcc/kilauea/kilauea.c create mode 100644 board/amcc/kilauea/memory.c create mode 100644 board/amcc/kilauea/u-boot.lds create mode 100644 include/configs/kilauea.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index b8c1fdc9d06..9ec7a5c24fd 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -304,6 +304,7 @@ Stefan Roese bunbinga PPC405EP ebony PPC440GP katmai PPC440SPe + kilauea PPC405EX lwmon5 PPC440EPx ocotea PPC440GX p3p440 PPC440GP diff --git a/MAKEALL b/MAKEALL index 20e81370f7c..83c498c219a 100755 --- a/MAKEALL +++ b/MAKEALL @@ -187,6 +187,7 @@ LIST_4xx=" \ JSE \ KAREF \ katmai \ + kilauea \ luan \ lwmon5 \ METROBOX \ diff --git a/Makefile b/Makefile index 5643aa91213..ba96ca1de37 100644 --- a/Makefile +++ b/Makefile @@ -1168,6 +1168,9 @@ KAREF_config: unconfig katmai_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx katmai amcc +kilauea_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx kilauea amcc + luan_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx luan amcc diff --git a/board/amcc/kilauea/Makefile b/board/amcc/kilauea/Makefile new file mode 100644 index 00000000000..b8da25ff426 --- /dev/null +++ b/board/amcc/kilauea/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o cmd_pll.o memory.o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend *~ + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/amcc/kilauea/cmd_pll.c b/board/amcc/kilauea/cmd_pll.c new file mode 100644 index 00000000000..b2666dd83b0 --- /dev/null +++ b/board/amcc/kilauea/cmd_pll.c @@ -0,0 +1,297 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * ehnus: change pll frequency. + * Wed Sep 5 11:45:17 CST 2007 + * hsun@udtech.com.cn + */ + + +#include +#include +#include +#include + +#ifdef CONFIG_CMD_EEPROM + +#define EEPROM_CONF_OFFSET 0 +#define EEPROM_TEST_OFFSET 16 +#define EEPROM_SDSTP_PARAM 16 + +#define PLL_NAME_MAX 12 +#define BUF_STEP 8 + +/* eeprom_wirtes 8Byte per op. */ +#define EEPROM_ALTER_FREQ(freq) \ + do { \ + int __i; \ + for (__i = 0; __i < 2; __i++) \ + eeprom_write (CFG_I2C_EEPROM_ADDR, \ + EEPROM_CONF_OFFSET + __i*BUF_STEP, \ + pll_select[freq], \ + BUF_STEP + __i*BUF_STEP); \ + } while (0) + +#define PDEBUG +#ifdef PDEBUG +#define PLL_DEBUG pll_debug(EEPROM_CONF_OFFSET) +#else +#define PLL_DEBUG +#endif + +typedef enum { + PLL_ebc20, + PLL_333, + PLL_4001, + PLL_4002, + PLL_533, + PLL_600, + PLL_666, /* For now, kilauea can't support */ + RCONF, + WTEST, + PLL_TOTAL +} pll_freq_t; + +static const char +pll_name[][PLL_NAME_MAX] = { + "PLL_ebc20", + "PLL_333", + "PLL_400@1", + "PLL_400@2", + "PLL_533", + "PLL_600", + "PLL_666", + "RCONF", + "WTEST", + "" +}; + +/* + * ehnus: + */ +static uchar +pll_select[][EEPROM_SDSTP_PARAM] = { + /* 0: CPU 333MHz EBC 20MHz, for test only */ + { + 0x8c, 0x12, 0xec, 0x12, 0x88, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 0: 333 */ + { + 0x8c, 0x12, 0xec, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 1: 400_266 */ + { + 0x8e, 0x0e, 0xe8, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 2: 400 */ + { + 0x8e, 0x0e, 0xe8, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 3: 533 */ + { + 0x8e, 0x43, 0x60, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 4: 600 */ + { + 0x8d, 0x02, 0x34, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 5: 666 */ + { + 0x8d, 0x03, 0x78, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + {} +}; + +static uchar +testbuf[EEPROM_SDSTP_PARAM] = { + 0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, + 0x88, 0x99, 0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff +}; + +static void +pll_debug(int off) +{ + int i; + uchar buffer[EEPROM_SDSTP_PARAM]; + + memset(buffer, 0, sizeof(buffer)); + eeprom_read(CFG_I2C_EEPROM_ADDR, off, + buffer, EEPROM_SDSTP_PARAM); + + printf("Debug: SDSTP[0-3] at offset \"0x%02x\" lists as follows: \n", off); + for (i = 0; i < EEPROM_SDSTP_PARAM; i++) + printf("%02x ", buffer[i]); + printf("\n"); +} + +static void +test_write(void) +{ + printf("Debug: test eeprom_write ... "); + + /* + * Write twice, 8 bytes per write + */ + eeprom_write (CFG_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET, + testbuf, 8); + eeprom_write (CFG_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET+8, + testbuf, 16); + printf("done\n"); + + pll_debug(EEPROM_TEST_OFFSET); +} + +int +do_pll_alter (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + char c = '\0'; + pll_freq_t pll_freq; + if (argc < 2) { + printf("Usage: \n%s\n", cmdtp->usage); + goto ret; + } + + for (pll_freq = PLL_ebc20; pll_freq < PLL_TOTAL; pll_freq++) + if (!strcmp(pll_name[pll_freq], argv[1])) + break; + + switch (pll_freq) { + case PLL_ebc20: + case PLL_333: + case PLL_4001: + case PLL_4002: + case PLL_533: + case PLL_600: + EEPROM_ALTER_FREQ(pll_freq); + break; + + case PLL_666: /* not support */ + printf("Choose this option will result in a boot failure." + "\nContinue? (Y/N): "); + + c = getc(); putc('\n'); + + if ((c == 'y') || (c == 'Y')) { + EEPROM_ALTER_FREQ(pll_freq); + break; + } + goto ret; + + case RCONF: + pll_debug(EEPROM_CONF_OFFSET); + goto ret; + case WTEST: + printf("DEBUG: write test\n"); + test_write(); + goto ret; + + default: + printf("Invalid options" + "\n\nUsage: \n%s\n", cmdtp->usage); + goto ret; + } + + printf("PLL set to %s, " + "reset the board to take effect\n", pll_name[pll_freq]); + + PLL_DEBUG; +ret: + return 0; +} + +U_BOOT_CMD( + pllalter, CFG_MAXARGS, 1, do_pll_alter, + "pllalter- change pll frequence \n", + "pllalter - change pll frequence \n\n\ + ** New freq take effect after reset. ** \n\ + ----------------------------------------------\n\ + PLL_ebc20: Board: AMCC 405EX(r) Evaluation Board\n\ + \t Same as PLL_333 \n\ + \t except \n\ + \t EBC: 20 MHz \n\ + ----------------------------------------------\n\ + PLL_333: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 666 MHz \n\ + \t CPU: 333 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 83 MHz \n\ + ------------------------------------------------\n\ + PLL_400@1: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 133 MHz \n\ + \t OPB: 66 MHz \n\ + \t DDR: 133 MHz \n\ + ------------------------------------------------\n\ + PLL_400@2: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_533: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1066 MHz \n\ + \t CPU: 533 MHz \n\ + \t PLB: 177 MHz \n\ + \t OPB: 88 MHz \n\ + \t DDR: 177 MHz \n\ + ----------------------------------------------\n\ + PLL_600: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1200 MHz \n\ + \t CPU: 600 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_666: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1333 MHz \n\ + \t CPU: 666 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 166 MHz \n\ + -----------------------------------------------\n\ + RCONF: Read current eeprom configuration. \n\ + -----------------------------------------------\n\ + WTEST: Test EEPROM write with predefined values\n\ + -----------------------------------------------\n" + ); + +#endif /* (CONFIG_COMMANDS & CFG_CMD_EEPROM) */ diff --git a/board/amcc/kilauea/config.mk b/board/amcc/kilauea/config.mk new file mode 100644 index 00000000000..a46b1972492 --- /dev/null +++ b/board/amcc/kilauea/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xFFFA0000 diff --git a/board/amcc/kilauea/init.S b/board/amcc/kilauea/init.S new file mode 100644 index 00000000000..c181d616972 --- /dev/null +++ b/board/amcc/kilauea/init.S @@ -0,0 +1,152 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Based on code provided from UDTech and AMCC + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#include +#include + +#define mtsdram_as(reg, value) \ + addi r4,0,reg ; \ + mtdcr memcfga,r4 ; \ + addis r4,0,value@h ; \ + ori r4,r4,value@l ; \ + mtdcr memcfgd,r4 ; + + .globl ext_bus_cntlr_init +ext_bus_cntlr_init: + + /* + * DDR2 setup + */ + + /* Following the DDR Core Manual, here is the initialization */ + + /* Step 1 */ + + /* Step 2 */ + + /* Step 3 */ + + /* SET SDRAM_MB0CF base addr 00000000 - 128MB */ + mtsdram_as(SDRAM_MB0CF, 0x00007701); /* 8 -- 7*/ + + /* SET SDRAM_MB1CF - Not enabled */ + mtsdram_as(SDRAM_MB1CF, 0x00000000); + + /* SET SDRAM_MB2CF - Not enabled */ + mtsdram_as(SDRAM_MB2CF, 0x00000000); + + /* SET SDRAM_MB3CF - Not enabled */ + mtsdram_as(SDRAM_MB3CF, 0x00000000); + + /* SDRAM_CLKTR: Adv Addr clock by 90 deg */ + mtsdram_as(SDRAM_CLKTR,0x80000000); + + /* Refresh Time register (0x30) Refresh every 7.8125uS */ + mtsdram_as(SDRAM_RTR, 0x06180000); + + /* SDRAM_SDTR1 */ + mtsdram_as(SDRAM_SDTR1,0x80201000); + + /* SDRAM_SDTR2 */ + mtsdram_as(SDRAM_SDTR2,0x32204232); + + /* SDRAM_SDTR3 */ + mtsdram_as(SDRAM_SDTR3,0x080b0d1a); + + mtsdram_as(SDRAM_MMODE, 0x00000442); + mtsdram_as(SDRAM_MEMODE, 0x00000404); + + /* SDRAM0_MCOPT1 (0X20) No ECC Gen */ + mtsdram_as(SDRAM_MCOPT1, 0x04322000); + + /* NOP */ + mtsdram_as(SDRAM_INITPLR0, 0xa8380000); + /* precharge 3 DDR clock cycle */ + mtsdram_as(SDRAM_INITPLR1, 0x81900400); + /* EMR2 twr = 2tck */ + mtsdram_as(SDRAM_INITPLR2, 0x81020000); + /* EMR3 twr = 2tck */ + mtsdram_as(SDRAM_INITPLR3, 0x81030000); + /* EMR DLL ENABLE twr = 2tck */ + mtsdram_as(SDRAM_INITPLR4, 0x81010404); + /* MR w/ DLL reset + * Note: 5 is CL. May need to be changed + */ + mtsdram_as(SDRAM_INITPLR5, 0x81000542); + /* precharge 3 DDR clock cycle */ + mtsdram_as(SDRAM_INITPLR6, 0x81900400); + /* Auto-refresh trfc = 26tck */ + mtsdram_as(SDRAM_INITPLR7, 0x8D080000); + /* Auto-refresh trfc = 26tck */ + mtsdram_as(SDRAM_INITPLR8, 0x8D080000); + /* Auto-refresh */ + mtsdram_as(SDRAM_INITPLR9, 0x8D080000); + /* Auto-refresh */ + mtsdram_as(SDRAM_INITPLR10, 0x8D080000); + /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */ + mtsdram_as(SDRAM_INITPLR11, 0x81000442); + mtsdram_as(SDRAM_INITPLR12, 0x81010780); + mtsdram_as(SDRAM_INITPLR13, 0x81010400); + mtsdram_as(SDRAM_INITPLR14, 0x00000000); + mtsdram_as(SDRAM_INITPLR15, 0x00000000); + + /* SET MCIF0_CODT Die Termination On */ + mtsdram_as(SDRAM_CODT, 0x0080f837); + mtsdram_as(SDRAM_MODT0, 0x01800000); + mtsdram_as(SDRAM_MODT1, 0x00000000); + + mtsdram_as(SDRAM_WRDTR, 0x00000000); + + /* SDRAM0_MCOPT2 (0X21) Start initialization */ + mtsdram_as(SDRAM_MCOPT2, 0x20000000); + + /* Step 5 */ + lis r3,0x1 /* 400000 = wait 100ms */ + mtctr r3 + +pll_wait: + bdnz pll_wait + + /* Step 6 */ + + /* SDRAM_DLCR */ + mtsdram_as(SDRAM_DLCR,0x030000a5); + + /* SDRAM_RDCC */ + mtsdram_as(SDRAM_RDCC,0x40000000); + + /* SDRAM_RQDC */ + mtsdram_as(SDRAM_RQDC,0x80000038); + + /* SDRAM_RFDC */ + mtsdram_as(SDRAM_RFDC,0x00000209); + + /* Enable memory controller */ + mtsdram_as(SDRAM_MCOPT2, 0x28000000); + + blr diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c new file mode 100644 index 00000000000..d91ee17a909 --- /dev/null +++ b/board/amcc/kilauea/kilauea.c @@ -0,0 +1,386 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_PCI) +#include +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +void fpga_init(void) +{ + /* + * Set FPGA regs + */ + out32(CFG_FPGA_BASE, 0xff570cc0); +} + +/* + * Board early initialization function + */ +int board_early_init_f (void) +{ + u32 val; + + /*--------------------------------------------------------------------+ + | Interrupt controller setup for the AMCC 405EX(r) PINE evaluation board. + +--------------------------------------------------------------------+ + +---------------------------------------------------------------------+ + |Interrupt| Source | Pol. | Sensi.| Crit. | + +---------+-----------------------------------+-------+-------+-------+ + | IRQ 00 | UART0 | High | Level | Non | + | IRQ 01 | UART1 | High | Level | Non | + | IRQ 02 | IIC0 | High | Level | Non | + | IRQ 03 | TBD | High | Level | Non | + | IRQ 04 | TBD | High | Level | Non | + | IRQ 05 | EBM | High | Level | Non | + | IRQ 06 | BGI | High | Level | Non | + | IRQ 07 | IIC1 | Rising| Edge | Non | + | IRQ 08 | SPI | High | Lvl/ed| Non | + | IRQ 09 | External IRQ 0 - (PCI-Express) | pgm H | Pgm | Non | + | IRQ 10 | MAL TX EOB | High | Level | Non | + | IRQ 11 | MAL RX EOB | High | Level | Non | + | IRQ 12 | DMA Channel 0 FIFO Full | High | Level | Non | + | IRQ 13 | DMA Channel 0 Stat FIFO | High | Level | Non | + | IRQ 14 | DMA Channel 1 FIFO Full | High | Level | Non | + | IRQ 15 | DMA Channel 1 Stat FIFO | High | Level | Non | + | IRQ 16 | PCIE0 AL | high | Level | Non | + | IRQ 17 | PCIE0 VPD access | rising| Edge | Non | + | IRQ 18 | PCIE0 hot reset request | rising| Edge | Non | + | IRQ 19 | PCIE0 hot reset request | faling| Edge | Non | + | IRQ 20 | PCIE0 TCR | High | Level | Non | + | IRQ 21 | PCIE0 MSI level0 | High | Level | Non | + | IRQ 22 | PCIE0 MSI level1 | High | Level | Non | + | IRQ 23 | Security EIP-94 | High | Level | Non | + | IRQ 24 | EMAC0 interrupt | High | Level | Non | + | IRQ 25 | EMAC1 interrupt | High | Level | Non | + | IRQ 26 | PCIE0 MSI level2 | High | Level | Non | + | IRQ 27 | External IRQ 4 | pgm H | Pgm | Non | + | IRQ 28 | UIC2 Non-critical Int. | High | Level | Non | + | IRQ 29 | UIC2 Critical Interrupt | High | Level | Crit. | + | IRQ 30 | UIC1 Non-critical Int. | High | Level | Non | + | IRQ 31 | UIC1 Critical Interrupt | High | Level | Crit. | + |---------------------------------------------------------------------- + | IRQ 32 | MAL Serr | High | Level | Non | + | IRQ 33 | MAL Txde | High | Level | Non | + | IRQ 34 | MAL Rxde | High | Level | Non | + | IRQ 35 | PCIE0 bus master VC0 |falling| Edge | Non | + | IRQ 36 | PCIE0 DCR Error | High | Level | Non | + | IRQ 37 | EBC | High |Lvl Edg| Non | + | IRQ 38 | NDFC | High | Level | Non | + | IRQ 39 | GPT Compare Timer 8 | Risin | Edge | Non | + | IRQ 40 | GPT Compare Timer 9 | Risin | Edge | Non | + | IRQ 41 | PCIE1 AL | high | Level | Non | + | IRQ 42 | PCIE1 VPD access | rising| edge | Non | + | IRQ 43 | PCIE1 hot reset request | rising| Edge | Non | + | IRQ 44 | PCIE1 hot reset request | faling| Edge | Non | + | IRQ 45 | PCIE1 TCR | High | Level | Non | + | IRQ 46 | PCIE1 bus master VC0 |falling| Edge | Non | + | IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non | + | IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non | + | IRQ 49 | Ext. IRQ 7 |pgm/Fal|pgm/Lvl| Non | + | IRQ 50 | Ext. IRQ 8 - |pgm (H)|pgm/Lvl| Non | + | IRQ 51 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non | + | IRQ 52 | GPT Compare Timer 5 | high | Edge | Non | + | IRQ 53 | GPT Compare Timer 6 | high | Edge | Non | + | IRQ 54 | GPT Compare Timer 7 | high | Edge | Non | + | IRQ 55 | Serial ROM | High | Level | Non | + | IRQ 56 | GPT Decrement Pulse | High | Level | Non | + | IRQ 57 | Ext. IRQ 2 |pgm/Fal|pgm/Lvl| Non | + | IRQ 58 | Ext. IRQ 5 |pgm/Fal|pgm/Lvl| Non | + | IRQ 59 | Ext. IRQ 6 |pgm/Fal|pgm/Lvl| Non | + | IRQ 60 | EMAC0 Wake-up | High | Level | Non | + | IRQ 61 | Ext. IRQ 1 |pgm/Fal|pgm/Lvl| Non | + | IRQ 62 | EMAC1 Wake-up | High | Level | Non | + |---------------------------------------------------------------------- + | IRQ 64 | PE0 AL | High | Level | Non | + | IRQ 65 | PE0 VPD Access | Risin | Edge | Non | + | IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non | + | IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non | + | IRQ 68 | PE0 TCR | High | Level | Non | + | IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non | + | IRQ 70 | PE0 DCR Error | High | Level | Non | + | IRQ 71 | Reserved | N/A | N/A | Non | + | IRQ 72 | PE1 AL | High | Level | Non | + | IRQ 73 | PE1 VPD Access | Risin | Edge | Non | + | IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non | + | IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non | + | IRQ 76 | PE1 TCR | High | Level | Non | + | IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non | + | IRQ 78 | PE1 DCR Error | High | Level | Non | + | IRQ 79 | Reserved | N/A | N/A | Non | + | IRQ 80 | PE2 AL | High | Level | Non | + | IRQ 81 | PE2 VPD Access | Risin | Edge | Non | + | IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non | + | IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non | + | IRQ 84 | PE2 TCR | High | Level | Non | + | IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non | + | IRQ 86 | PE2 DCR Error | High | Level | Non | + | IRQ 87 | Reserved | N/A | N/A | Non | + | IRQ 88 | External IRQ(5) | Progr | Progr | Non | + | IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non | + | IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non | + | IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non | + | IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non | + | IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non | + | IRQ 94 | Reserved | N/A | N/A | Non | + | IRQ 95 | Reserved | N/A | N/A | Non | + |--------------------------------------------------------------------- + +---------+-----------------------------------+-------+-------+------*/ + /*--------------------------------------------------------------------+ + | Initialise UIC registers. Clear all interrupts. Disable all + | interrupts. + | Set critical interrupt values. Set interrupt polarities. Set + | interrupt trigger levels. Make bit 0 High priority. Clear all + | interrupts again. + +-------------------------------------------------------------------*/ + + mtdcr (uic2sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic2er, 0x00000000); /* disable all interrupts */ + mtdcr (uic2cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic2pr, 0xf7ffffff); /* Set Interrupt Polarities */ + mtdcr (uic2tr, 0x01e1fff8); /* Set Interrupt Trigger Levels */ + mtdcr (uic2vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic2sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic2sr, 0xffffffff); /* clear all interrupts */ + + mtdcr (uic1sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic1er, 0x00000000); /* disable all interrupts */ + mtdcr (uic1cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic1pr, 0xfffac785); /* Set Interrupt Polarities */ + mtdcr (uic1tr, 0x001d0040); /* Set Interrupt Trigger Levels */ + mtdcr (uic1vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic1sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic1sr, 0xffffffff); /* clear all interrupts */ + + mtdcr (uic0sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic0er, 0x0000000a); /* Disable all interrupts */ + /* Except cascade UIC0 and UIC1 */ + mtdcr (uic0cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic0pr, 0xffbfefef); /* Set Interrupt Polarities */ + mtdcr (uic0tr, 0x00007000); /* Set Interrupt Trigger Levels */ + mtdcr (uic0vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic0sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */ + + /* + * Note: Some cores are still in reset when the chip starts, so + * take them out of reset + */ + mtsdr(SDR0_SRST, 0); + + fpga_init(); + + /* Configure 405EX for NAND usage */ + val = SDR0_CUST0_MUX_NDFC_SEL | + SDR0_CUST0_NDFC_ENABLE | + SDR0_CUST0_NDFC_BW_8_BIT | + SDR0_CUST0_NRB_BUSY | + (0x80000000 >> (28 + CFG_NAND_CS)); + mtsdr(SDR0_CUST0, val); + + return 0; +} + +int misc_init_r(void) +{ +#ifdef CFG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + -CFG_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); +#endif + + return 0; +} + +int checkboard (void) +{ + char *s = getenv("serial#"); + + printf("Board: Kilauea - AMCC PPC405EX Evaluation Board"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return (0); +} + +/************************************************************************* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + ************************************************************************/ +#if defined(CONFIG_PCI) +int pci_pre_init(struct pci_controller * hose ) +{ + return 0; +} +#endif /* defined(CONFIG_PCI) */ + +/************************************************************************* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller * hose ) +{ + /*-------------------------------------------------------------------+ + * Disable everything + *-------------------------------------------------------------------*/ + out32r( PCIX0_PIM0SA, 0 ); /* disable */ + out32r( PCIX0_PIM1SA, 0 ); /* disable */ + out32r( PCIX0_PIM2SA, 0 ); /* disable */ + out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */ + + /*-------------------------------------------------------------------+ + * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 + * strapping options to not support sizes such as 128/256 MB. + *-------------------------------------------------------------------*/ + out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE ); + out32r( PCIX0_PIM0LAH, 0 ); + out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 ); + + out32r( PCIX0_BAR0, 0 ); + + /*-------------------------------------------------------------------+ + * Program the board's subsystem id/vendor id + *-------------------------------------------------------------------*/ + out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID ); + out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID ); + + out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY ); +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ + +#ifdef CONFIG_PCI +static int pcie_port_is_rootpoint(int port) +{ + return 1; +} + +static struct pci_controller pcie_hose[2] = {{0},{0}}; + +void pcie_setup_hoses(int busno) +{ + struct pci_controller *hose; + int i, bus; + bus = busno; + char *env; + unsigned int delay; + + for (i = 0; i < 2; i++) { + + if (pcie_port_is_rootpoint(i)) { + printf("PORT%d will be configured as root-complex\n", i); + if (ppc4xx_init_pcie_rootport(i)) { + printf("PCIE%d: initialization failed\n", i); + continue; + } + } else { + printf("PORT%d will be configured as endpoint\n", i); + if (ppc4xx_init_pcie_endport(i)) { + printf("PCIE%d: initialization failed\n", i); + continue; + } + } + + hose = &pcie_hose[i]; + hose->first_busno = bus; + hose->last_busno = bus; + hose->current_busno = bus; + + /* setup mem resource */ + pci_set_region(hose->regions + 0, + CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, + CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, + CFG_PCIE_MEMSIZE, + PCI_REGION_MEM); + hose->region_count = 1; + pci_register_hose(hose); + + if (pcie_port_is_rootpoint(i)) + ppc4xx_setup_pcie_rootpoint(hose, i); + else + ppc4xx_setup_pcie_endpoint(hose, i); + + env = getenv("pciscandelay"); + if (env != NULL) { + delay = simple_strtoul(env, NULL, 10); + if (delay > 5) + printf("Warning, expect noticable delay before PCIe" + "scan due to 'pciscandelay' value!\n"); + mdelay(delay * 1000); + } + + /* + * Config access can only go down stream + */ + hose->last_busno = pci_hose_scan(hose); + bus = hose->last_busno + 1; + } +} +#endif + +#if defined(CONFIG_POST) +/* + * Returns 1 if keys pressed to start the power-on long-running tests + * Called from board_init_f(). + */ +int post_hotkeys_pressed(void) +{ + return 0; /* No hotkeys supported */ +} +#endif /* CONFIG_POST */ + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/amcc/kilauea/memory.c b/board/amcc/kilauea/memory.c new file mode 100644 index 00000000000..1d7a3fad979 --- /dev/null +++ b/board/amcc/kilauea/memory.c @@ -0,0 +1,79 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +void sdram_init(void) +{ + return; +} + +long int initdram(int board_type) +{ + return (CFG_MBYTES_SDRAM << 20); +} + +#if defined(CFG_DRAM_TEST) +int testdram (void) +{ + printf ("testdram\n"); +#if defined (CONFIG_NAND_U_BOOT) + return 0; +#endif + uint *pstart = (uint *) 0x00000000; + uint *pend = (uint *) 0x00001000; + uint *p; + + for (p = pstart; p < pend; p++) { + *p = 0xaaaaaaaa; + } + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test fails at: %08x\n", (uint) p); +#endif + return 1; + } + } + + for (p = pstart; p < pend; p++) { + *p = 0x55555555; + } + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test fails at: %08x\n", (uint) p); +#endif + return 1; + } + } +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test passed!!!\n"); +#endif + return 0; +} +#endif diff --git a/board/amcc/kilauea/u-boot.lds b/board/amcc/kilauea/u-boot.lds new file mode 100644 index 00000000000..390b3f397b2 --- /dev/null +++ b/board/amcc/kilauea/u-boot.lds @@ -0,0 +1,137 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ +/* To compile successfully, uncomment the following section. + * To go in ram, remove the section. + * Added by SunHe. + */ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h new file mode 100644 index 00000000000..7858f831981 --- /dev/null +++ b/include/configs/kilauea.h @@ -0,0 +1,486 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * kilauea.h - configuration for AMCC Kilauea (405EX) + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_KILAUEA 1 /* Board is Kilauea */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_405EX 1 /* Specifc 405EX support*/ +#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFC000000 +#define CFG_NAND_ADDR 0xF8000000 +#define CFG_FPGA_BASE 0xF0000000 +#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE (TEXT_BASE) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +/* reserve some memory for POST and BOOT limit info */ +#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) + +/* extra data in init-ram */ +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) +#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8) +#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12) +#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ +#endif + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ +#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ + +/* Standard DTT sensor configuration */ +#define CONFIG_DTT_DS1775 1 +#define CONFIG_DTT_SENSORS { 0 } +#define CFG_I2C_DTT_ADDR 0x48 + +/* RTC configuration */ +#define CONFIG_RTC_DS1338 1 +#define CFG_I2C_RTC_ADDR 0x68 + +/*----------------------------------------------------------------------- + * Ethernet + *----------------------------------------------------------------------*/ +#define CONFIG_M88E1111_PHY 1 +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 1 + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 2 + +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#undef USE_LIBFDT +#ifdef USE_LIBFDT +/* + * LIBFDT support is disabled for now since first Linux port is still + * arch/ppc. + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "logversion=2\0" \ + "netdev=eth0\0" \ + "hostname=kilauea\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "net_nfs=tftp 200000 ${bootfile};" \ + "tftp ${fdt_addr} ${fdt_file};" \ + "run nfsargs addip addtty;" \ + "bootm 200000 - ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=kilauea/uImage\0" \ + "fdt_file=kilauea/kilauea.dtb\0" \ + "fdt_addr=400000\0" \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc200000\0" \ + "initrd_high=30000000\0" \ + "load=tftp 200000 kilauea/u-boot.bin\0" \ + "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ + "cp.b ${fileaddr} fffa0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ + "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ + "setenv filesize;saveenv\0" \ + "nupd=run nload nupdate\0" \ + "" +#else +#define CONFIG_EXTRA_ENV_SETTINGS \ + "logversion=2\0" \ + "netdev=eth0\0" \ + "hostname=kilauea\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty;" \ + "bootm 200000\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=kilauea/uImage\0" \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc200000\0" \ + "initrd_high=30000000\0" \ + "load=tftp 200000 kilauea/u-boot.bin\0" \ + "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ + "cp.b ${fileaddr} fffa0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ + "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ + "setenv filesize;saveenv\0" \ + "nupd=run nload nupdate\0" \ + "pciconfighost=1\0" \ + "" +#endif +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_LOG +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CACHE | \ + CFG_POST_CPU | \ + CFG_POST_ETHER | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_UART) + +/* Define here the base-addresses of the UARTs to test in POST */ +#define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE} + +#define CONFIG_LOGBUFFER +#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ + +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCI_CONFIG_HOST_BRIDGE + +/*----------------------------------------------------------------------- + * PCIe stuff + *----------------------------------------------------------------------*/ +#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ +#define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ + +#define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */ +#define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */ +#define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ + +#define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */ +#define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */ +#define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ + +#define CFG_PCIE0_UTLBASE 0xef502000 +#define CFG_PCIE1_UTLBASE 0xef503000 + +/* base address of inbound PCIe window */ +#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Cache Configuration + *----------------------------------------------------------------------*/ +#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */ +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CFG_NAND_CS 1 /* NAND chip connected to CSx */ + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x05806500 +#define CFG_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 1 (NAND-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x018003c0 +#define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000) + +/* Memory Bank 2 (FPGA) initialization */ +#define CFG_EBC_PB2AP 0x9400C800 +#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */ + +#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ + +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ + +/*----------------------------------------------------------------------- + * GPIO Setup + *----------------------------------------------------------------------*/ +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EX specific) + * + * GPIO0[0-3] - EBC data 0-3 inputs/outputs + * GPIO0[4-7] - USB data 4-7 inputs/outputs + * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs + * GPIO0[12-15] - USB data 0-3 inputs/outputs + * GPIO0[16-21] - UART0 control signal inputs/outputs + * + * GPIO0[22-25,27] - EBC control signal inputs/outputs + * GPIO0[26] - Instruction trace outputs + * GPIO0[28] - Float, N/C + * GPIO0[29-31] - DMA control signal inputs/outputs + */ +#define CFG_GPIO0_OSRL 0x00AA54AA +#define CFG_GPIO0_OSRH 0x21800000 +#define CFG_GPIO0_TSRL 0x00AA55AA +#define CFG_GPIO0_TSRH 0xA5A00000 + +#define CFG_GPIO0_ISR1L 0x00000100 +#define CFG_GPIO0_ISR1H 0x04000000 +#define CFG_GPIO0_ISR2L 0x00550055 +#define CFG_GPIO0_ISR2H 0x40100000 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/*----------------------------------------------------------------------- + * Some Kilauea stuff..., mainly fpga registers + */ +#define CFG_FPGA_REG_BASE CFG_FPGA_BASE +#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 11)) + +/* interrupt */ +#define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000 +#define CFG_FPGA_SLIC0_W_DPRAM_INT 0x40000000 +#define CFG_FPGA_SLIC1_R_DPRAM_INT 0x20000000 +#define CFG_FPGA_SLIC1_W_DPRAM_INT 0x10000000 +#define CFG_FPGA_PHY0_INT 0x08000000 +#define CFG_FPGA_PHY1_INT 0x04000000 +#define CFG_FPGA_SLIC0_INT 0x02000000 +#define CFG_FPGA_SLIC1_INT 0x01000000 + +/* DPRAM setting */ +/* 00: 32B; 01: 64B; 10: 128B; 11: 256B */ +#define CFG_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */ +#define CFG_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */ +#define CFG_FPGA_DPRAM_RW_TYPE 0x00080000 +#define CFG_FPGA_DPRAM_RST 0x00040000 +#define CFG_FPGA_UART0_FO 0x00020000 +#define CFG_FPGA_UART1_FO 0x00010000 + +/* loopback */ +#define CFG_FPGA_CHIPSIDE_LOOPBACK 0x00004000 +#define CFG_FPGA_LINESIDE_LOOPBACK 0x00008000 +#define CFG_FPGA_SLIC0_ENABLE 0x00002000 +#define CFG_FPGA_SLIC1_ENABLE 0x00001000 +#define CFG_FPGA_SLIC0_CS 0x00000800 +#define CFG_FPGA_SLIC1_CS 0x00000400 +#define CFG_FPGA_USER_LED0 0x00000200 +#define CFG_FPGA_USER_LED1 0x00000100 + +#endif /* __CONFIG_H */ + +#ifdef USE_LIBFDT +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,405EX@0" +#endif -- cgit v1.3.1 From db3232ddb058d0ed0bc31f7c5c296748a1afac67 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 5 Oct 2007 21:28:58 +0200 Subject: ppc4xx: Fix small merge problems with CPCI440 and Acadia boards Signed-off-by: Stefan Roese --- board/esd/cpci440/cpci440.c | 2 +- include/ppc405.h | 256 -------------------------------------------- 2 files changed, 1 insertion(+), 257 deletions(-) (limited to 'include') diff --git a/board/esd/cpci440/cpci440.c b/board/esd/cpci440/cpci440.c index 43d8a3b3bf0..caa6d5591fd 100644 --- a/board/esd/cpci440/cpci440.c +++ b/board/esd/cpci440/cpci440.c @@ -79,7 +79,7 @@ int checkboard (void) printf("\tCPU: %lu MHz\n", sysinfo.freqProcessor/1000000); printf("\tPLB: %lu MHz\n", sysinfo.freqPLB/1000000); printf("\tOPB: %lu MHz\n", sysinfo.freqOPB/1000000); - printf("\tEPB: %lu MHz\n", sysinfo.freqEPB/1000000); + printf("\tEBC: %lu MHz\n", sysinfo.freqEBC/1000000); /* * Disable sleep mode in LXT971 diff --git a/include/ppc405.h b/include/ppc405.h index 82bc25e1f41..4d2514425e2 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -742,10 +742,6 @@ /****************************************************************************** * Control ******************************************************************************/ -#define CNTRL_DCR_BASE 0x0C -#define cprcfga (CNTRL_DCR_BASE+0x0) /* CPR addr reg */ -#define cprcfgd (CNTRL_DCR_BASE+0x1) /* CPR data reg */ - /* CPR Registers */ #define cprclkupd 0x020 /* CPR_CLKUPD */ #define cprpllc 0x040 /* CPR_PLLC */ @@ -757,12 +753,6 @@ #define cprmisc0 0x181 /* CPR_MISC0 */ #define cprmisc1 0x182 /* CPR_MISC1 */ -/* - * Macro for accessing the indirect CPR register - */ -#define mtcpr(reg, data) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,data); } while (0) -#define mfcpr(reg, data) do { mtdcr(cprcfga,reg);data = mfdcr(cprcfgd); } while (0) - #define CPR_CLKUPD_ENPLLCH_EN 0x40000000 /* Enable CPR PLL Changes */ #define CPR_CLKUPD_ENDVCH_EN 0x20000000 /* Enable CPR Sys. Div. Changes */ #define CPR_PERD0_SPIDV_MASK 0x000F0000 /* SPI Clock Divider */ @@ -783,252 +773,6 @@ #define PERD0_U0DV_MASK 0x0000FF00 /* UART 0 Divider Mask */ #define PERD0_U1DV_MASK 0x000000FF /* UART 1 Divider Mask */ -#if 0 /* Deprecated */ -#define CNTRL_DCR_BASE 0x0f0 -#define cpc0_pllmr0 (CNTRL_DCR_BASE+0x0) /* PLL mode register 0 */ -#define cpc0_boot (CNTRL_DCR_BASE+0x1) /* Clock status register */ -#define cpc0_epctl (CNTRL_DCR_BASE+0x3) /* EMAC to PHY control register */ -#define cpc0_pllmr1 (CNTRL_DCR_BASE+0x4) /* PLL mode register 1 */ -#define cpc0_ucr (CNTRL_DCR_BASE+0x5) /* UART control register */ -#define cpc0_pci (CNTRL_DCR_BASE+0x9) /* PCI control register */ - -#define CPC0_PLLMR0 (CNTRL_DCR_BASE+0x0) /* PLL mode 0 register */ -#define CPC0_BOOT (CNTRL_DCR_BASE+0x1) /* Chip Clock Status register */ -#define CPC0_CR1 (CNTRL_DCR_BASE+0x2) /* Chip Control 1 register */ -#define CPC0_EPRCSR (CNTRL_DCR_BASE+0x3) /* EMAC PHY Rcv Clk Src register*/ -#define CPC0_PLLMR1 (CNTRL_DCR_BASE+0x4) /* PLL mode 1 register */ -#define CPC0_UCR (CNTRL_DCR_BASE+0x5) /* UART Control register */ -#define CPC0_SRR (CNTRL_DCR_BASE+0x6) /* Soft Reset register */ -#define CPC0_JTAGID (CNTRL_DCR_BASE+0x7) /* JTAG ID register */ -#define CPC0_SPARE (CNTRL_DCR_BASE+0x8) /* Spare DCR */ -#define CPC0_PCI (CNTRL_DCR_BASE+0x9) /* PCI Control register */ - -/* Bit definitions */ -#define PLLMR0_CPU_DIV_MASK 0x00300000 /* CPU clock divider */ -#define PLLMR0_CPU_DIV_BYPASS 0x00000000 -#define PLLMR0_CPU_DIV_2 0x00100000 -#define PLLMR0_CPU_DIV_3 0x00200000 -#define PLLMR0_CPU_DIV_4 0x00300000 - -#define PLLMR0_CPU_TO_PLB_MASK 0x00030000 /* CPU:PLB Frequency Divisor */ -#define PLLMR0_CPU_PLB_DIV_1 0x00000000 -#define PLLMR0_CPU_PLB_DIV_2 0x00010000 -#define PLLMR0_CPU_PLB_DIV_3 0x00020000 -#define PLLMR0_CPU_PLB_DIV_4 0x00030000 - -#define PLLMR0_OPB_TO_PLB_MASK 0x00003000 /* OPB:PLB Frequency Divisor */ -#define PLLMR0_OPB_PLB_DIV_1 0x00000000 -#define PLLMR0_OPB_PLB_DIV_2 0x00001000 -#define PLLMR0_OPB_PLB_DIV_3 0x00002000 -#define PLLMR0_OPB_PLB_DIV_4 0x00003000 - -#define PLLMR0_EXB_TO_PLB_MASK 0x00000300 /* External Bus:PLB Divisor */ -#define PLLMR0_EXB_PLB_DIV_2 0x00000000 -#define PLLMR0_EXB_PLB_DIV_3 0x00000100 -#define PLLMR0_EXB_PLB_DIV_4 0x00000200 -#define PLLMR0_EXB_PLB_DIV_5 0x00000300 - -#define PLLMR0_MAL_TO_PLB_MASK 0x00000030 /* MAL:PLB Divisor */ -#define PLLMR0_MAL_PLB_DIV_1 0x00000000 -#define PLLMR0_MAL_PLB_DIV_2 0x00000010 -#define PLLMR0_MAL_PLB_DIV_3 0x00000020 -#define PLLMR0_MAL_PLB_DIV_4 0x00000030 - -#define PLLMR0_PCI_TO_PLB_MASK 0x00000003 /* PCI:PLB Frequency Divisor */ -#define PLLMR0_PCI_PLB_DIV_1 0x00000000 -#define PLLMR0_PCI_PLB_DIV_2 0x00000001 -#define PLLMR0_PCI_PLB_DIV_3 0x00000002 -#define PLLMR0_PCI_PLB_DIV_4 0x00000003 - -#define PLLMR1_SSCS_MASK 0x80000000 /* Select system clock source */ -#define PLLMR1_PLLR_MASK 0x40000000 /* PLL reset */ -#define PLLMR1_FBMUL_MASK 0x00F00000 /* PLL feedback multiplier value */ -#define PLLMR1_FBMUL_DIV_16 0x00000000 -#define PLLMR1_FBMUL_DIV_1 0x00100000 -#define PLLMR1_FBMUL_DIV_2 0x00200000 -#define PLLMR1_FBMUL_DIV_3 0x00300000 -#define PLLMR1_FBMUL_DIV_4 0x00400000 -#define PLLMR1_FBMUL_DIV_5 0x00500000 -#define PLLMR1_FBMUL_DIV_6 0x00600000 -#define PLLMR1_FBMUL_DIV_7 0x00700000 -#define PLLMR1_FBMUL_DIV_8 0x00800000 -#define PLLMR1_FBMUL_DIV_9 0x00900000 -#define PLLMR1_FBMUL_DIV_10 0x00A00000 -#define PLLMR1_FBMUL_DIV_11 0x00B00000 -#define PLLMR1_FBMUL_DIV_12 0x00C00000 -#define PLLMR1_FBMUL_DIV_13 0x00D00000 -#define PLLMR1_FBMUL_DIV_14 0x00E00000 -#define PLLMR1_FBMUL_DIV_15 0x00F00000 - -#define PLLMR1_FWDVA_MASK 0x00070000 /* PLL forward divider A value */ -#define PLLMR1_FWDVA_DIV_8 0x00000000 -#define PLLMR1_FWDVA_DIV_7 0x00010000 -#define PLLMR1_FWDVA_DIV_6 0x00020000 -#define PLLMR1_FWDVA_DIV_5 0x00030000 -#define PLLMR1_FWDVA_DIV_4 0x00040000 -#define PLLMR1_FWDVA_DIV_3 0x00050000 -#define PLLMR1_FWDVA_DIV_2 0x00060000 -#define PLLMR1_FWDVA_DIV_1 0x00070000 -#define PLLMR1_FWDVB_MASK 0x00007000 /* PLL forward divider B value */ -#define PLLMR1_TUNING_MASK 0x000003FF /* PLL tune bits */ - -/* Defines for CPC0_EPRCSR register */ -#define CPC0_EPRCSR_E0NFE 0x80000000 -#define CPC0_EPRCSR_E1NFE 0x40000000 -#define CPC0_EPRCSR_E1RPP 0x00000080 -#define CPC0_EPRCSR_E0RPP 0x00000040 -#define CPC0_EPRCSR_E1ERP 0x00000020 -#define CPC0_EPRCSR_E0ERP 0x00000010 -#define CPC0_EPRCSR_E1PCI 0x00000002 -#define CPC0_EPRCSR_E0PCI 0x00000001 - -/* Defines for CPC0_BOOR Register */ -#define CPC0_BOOT_SEP 0x00000002 /* serial EEPROM present */ - -/* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ -#define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ - -/* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 - -/* - *------------------------------------------------------------------------------- - * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI, - * assuming a 33.3MHz input clock to the 405EP. - *------------------------------------------------------------------------------- - */ -#define PLLMR0_266_133_66 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_266_133_66 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_133_66_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_133_66_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_266_133_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PLLMR1_266_133_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) -#define PLLMR0_266_66_33_33 (PLL_CPUDIV_1 | PLL_PLBDIV_4 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_2 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PLLMR1_266_66_33_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -/* - * PLL Voltage Controlled Oscillator (VCO) definitions - * Maximum and minimum values (in MHz) for correct PLL operation. - */ -#define VCO_MIN 500 -#define VCO_MAX 1000 -#endif /* #if 0 */ #else /* #ifdef CONFIG_405EP */ /****************************************************************************** * Control -- cgit v1.3.1 From fd671802b67a0ef37a06124fa2ce85f00aa22c6f Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 11 Oct 2007 11:15:59 +0200 Subject: ppc4xx: Enable device tree support (fdt) on Kilauea per default This patch enables the fdt support on the AMCC Kilauea eval board. Additionally now EBC ranges fdt fixup is included to support NOR FLASH mapping via the Linux physmap_of driver. This Kilauea port now support booting arch/ppc and arch/powerpc Linux kernels. The default environment "net_nfs" is for arch/ppc and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc support will be removed. Signed-off-by: Stefan Roese --- board/amcc/kilauea/kilauea.c | 14 ++++++++++++++ include/configs/kilauea.h | 46 +++----------------------------------------- 2 files changed, 17 insertions(+), 43 deletions(-) (limited to 'include') diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c index d91ee17a909..8767f758810 100644 --- a/board/amcc/kilauea/kilauea.c +++ b/board/amcc/kilauea/kilauea.c @@ -381,6 +381,20 @@ int post_hotkeys_pressed(void) #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) void ft_board_setup(void *blob, bd_t *bd) { + u32 val[4]; + int rc; + ft_cpu_setup(blob, bd); + + /* Fixup NOR mapping */ + val[0] = 0; /* chip select number */ + val[1] = 0; /* always 0 */ + val[2] = gd->bd->bi_flashstart; + val[3] = gd->bd->bi_flashsize; + rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", + val, sizeof(val), 1); + if (rc) + printf("Unable to update property NOR mapping, err=%s\n", + fdt_strerror(rc)); } #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 7858f831981..461f8f0591d 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -166,12 +166,6 @@ #undef CONFIG_BOOTARGS -#undef USE_LIBFDT -#ifdef USE_LIBFDT -/* - * LIBFDT support is disabled for now since first Linux port is still - * arch/ppc. - */ #define CONFIG_EXTRA_ENV_SETTINGS \ "logversion=2\0" \ "netdev=eth0\0" \ @@ -184,6 +178,9 @@ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty;" \ + "bootm 200000\0" \ + "net_nfs_fdt=tftp 200000 ${bootfile};" \ "tftp ${fdt_addr} ${fdt_file};" \ "run nfsargs addip addtty;" \ "bootm 200000 - ${fdt_addr}\0" \ @@ -207,43 +204,8 @@ "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ "setenv filesize;saveenv\0" \ "nupd=run nload nupdate\0" \ - "" -#else -#define CONFIG_EXTRA_ENV_SETTINGS \ - "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=kilauea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addtty;" \ - "bootm 200000\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=kilauea/uImage\0" \ - "kernel_addr=fc000000\0" \ - "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 kilauea/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "" -#endif #define CONFIG_BOOTCOMMAND "run flash_self" #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ @@ -477,10 +439,8 @@ #endif /* __CONFIG_H */ -#ifdef USE_LIBFDT /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define OF_CPU "PowerPC,405EX@0" -#endif -- cgit v1.3.1 From d4cb2d17946466740afeb195a57d6cb290bf4cc0 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 13 Oct 2007 16:43:23 +0200 Subject: ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint mode This patch adds support for dynamic configuration of PCIe ports for the AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe boards Yucca & Katmai and the 405EX board Kilauea. This dynamic configuration is done via the "pcie_mode" environement variable. This variable can be set to "EP" or "RP" for endpoint or rootpoint mode. Multiple values can be joined via the ":" delimiter. Here an example: pcie_mode=RP:EP:EP This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2 as endpoint. Per default Yucca will be configured as: pcie_mode=RP:EP:EP Per default Katmai will be configured as: pcie_mode=RP:RP:REP Per default Kilauea will be configured as: pcie_mode=RP:RP Signed-off-by: Tirumala R Marri Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 65 +++++++++++++++++++-------------------- board/amcc/kilauea/kilauea.c | 66 +++++++++++++++++++-------------------- board/amcc/yucca/yucca.c | 73 ++++++++++++++++++++++---------------------- cpu/ppc4xx/4xx_pcie.c | 22 ++++++++++++- include/asm-ppc/4xx_pcie.h | 52 +++++++++++++++++++++++++++++++ include/configs/katmai.h | 1 + include/configs/kilauea.h | 1 + include/configs/yucca.h | 1 + 8 files changed, 176 insertions(+), 105 deletions(-) (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index f1c352cb86e..0627a7a095c 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -30,9 +30,6 @@ #include #include -#undef PCIE_ENDPOINT -/* #define PCIE_ENDPOINT 1 */ - DECLARE_GLOBAL_DATA_PTR; int board_early_init_f (void) @@ -392,6 +389,7 @@ void pcie_setup_hoses(int busno) { struct pci_controller *hose; int i, bus; + int ret = 0; char *env; unsigned int delay; @@ -405,11 +403,14 @@ void pcie_setup_hoses(int busno) if (!katmai_pcie_card_present(i)) continue; -#ifdef PCIE_ENDPOINT - if (ppc4xx_init_pcie_endport(i)) { -#else - if (ppc4xx_init_pcie_rootport(i)) { -#endif + if (is_end_point(i)) { + printf("PCIE%d: will be configured as endpoint\n", i); + ret = ppc4xx_init_pcie_endport(i); + } else { + printf("PCIE%d: will be configured as root-complex\n", i); + ret = ppc4xx_init_pcie_rootport(i); + } + if (ret) { printf("PCIE%d: initialization failed\n", i); continue; } @@ -424,35 +425,33 @@ void pcie_setup_hoses(int busno) CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, CFG_PCIE_MEMSIZE, - PCI_REGION_MEM - ); + PCI_REGION_MEM); hose->region_count = 1; pci_register_hose(hose); -#ifdef PCIE_ENDPOINT - ppc4xx_setup_pcie_endpoint(hose, i); - /* - * Reson for no scanning is endpoint can not generate - * upstream configuration accesses. - */ -#else - ppc4xx_setup_pcie_rootpoint(hose, i); - - env = getenv ("pciscandelay"); - if (env != NULL) { - delay = simple_strtoul (env, NULL, 10); - if (delay > 5) - printf ("Warning, expect noticable delay before PCIe" - "scan due to 'pciscandelay' value!\n"); - mdelay (delay * 1000); + if (is_end_point(i)) { + ppc4xx_setup_pcie_endpoint(hose, i); + /* + * Reson for no scanning is endpoint can not generate + * upstream configuration accesses. + */ + } else { + ppc4xx_setup_pcie_rootpoint(hose, i); + env = getenv ("pciscandelay"); + if (env != NULL) { + delay = simple_strtoul(env, NULL, 10); + if (delay > 5) + printf("Warning, expect noticable delay before " + "PCIe scan due to 'pciscandelay' value!\n"); + mdelay(delay * 1000); + } + + /* + * Config access can only go down stream + */ + hose->last_busno = pci_hose_scan(hose); + bus = hose->last_busno + 1; } - - /* - * Config access can only go down stream - */ - hose->last_busno = pci_hose_scan(hose); - bus = hose->last_busno + 1; -#endif } } #endif /* defined(CONFIG_PCI) */ diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c index 8767f758810..b59bd6fc0e2 100644 --- a/board/amcc/kilauea/kilauea.c +++ b/board/amcc/kilauea/kilauea.c @@ -299,35 +299,29 @@ void pci_target_init(struct pci_controller * hose ) #endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ #ifdef CONFIG_PCI -static int pcie_port_is_rootpoint(int port) -{ - return 1; -} - static struct pci_controller pcie_hose[2] = {{0},{0}}; void pcie_setup_hoses(int busno) { struct pci_controller *hose; int i, bus; + int ret = 0; bus = busno; char *env; unsigned int delay; for (i = 0; i < 2; i++) { - if (pcie_port_is_rootpoint(i)) { - printf("PORT%d will be configured as root-complex\n", i); - if (ppc4xx_init_pcie_rootport(i)) { - printf("PCIE%d: initialization failed\n", i); - continue; - } + if (is_end_point(i)) { + printf("PCIE%d: will be configured as endpoint\n", i); + ret = ppc4xx_init_pcie_endport(i); } else { - printf("PORT%d will be configured as endpoint\n", i); - if (ppc4xx_init_pcie_endport(i)) { - printf("PCIE%d: initialization failed\n", i); - continue; - } + printf("PCIE%d: will be configured as root-complex\n", i); + ret = ppc4xx_init_pcie_rootport(i); + } + if (ret) { + printf("PCIE%d: initialization failed\n", i); + continue; } hose = &pcie_hose[i]; @@ -344,25 +338,29 @@ void pcie_setup_hoses(int busno) hose->region_count = 1; pci_register_hose(hose); - if (pcie_port_is_rootpoint(i)) - ppc4xx_setup_pcie_rootpoint(hose, i); - else - ppc4xx_setup_pcie_endpoint(hose, i); - - env = getenv("pciscandelay"); - if (env != NULL) { - delay = simple_strtoul(env, NULL, 10); - if (delay > 5) - printf("Warning, expect noticable delay before PCIe" - "scan due to 'pciscandelay' value!\n"); - mdelay(delay * 1000); - } + if (is_end_point(i)) { + ppc4xx_setup_pcie_endpoint(hose, i); + /* + * Reson for no scanning is endpoint can not generate + * upstream configuration accesses. + */ + } else { + ppc4xx_setup_pcie_rootpoint(hose, i); + env = getenv ("pciscandelay"); + if (env != NULL) { + delay = simple_strtoul(env, NULL, 10); + if (delay > 5) + printf("Warning, expect noticable delay before " + "PCIe scan due to 'pciscandelay' value!\n"); + mdelay(delay * 1000); + } - /* - * Config access can only go down stream - */ - hose->last_busno = pci_hose_scan(hose); - bus = hose->last_busno + 1; + /* + * Config access can only go down stream + */ + hose->last_busno = pci_hose_scan(hose); + bus = hose->last_busno + 1; + } } } #endif diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index c46721c9229..efdf814bf08 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -36,11 +36,8 @@ DECLARE_GLOBAL_DATA_PTR; -#undef PCIE_ENDPOINT -/* #define PCIE_ENDPOINT 1 */ void fpga_init (void); - void get_sys_info(PPC440_SYS_INFO *board_cfg ); int compare_to_true(char *str ); char *remove_l_w_space(char *in_str ); @@ -847,6 +844,7 @@ void pcie_setup_hoses(int busno) { struct pci_controller *hose; int i, bus; + int ret = 0; char *env; unsigned int delay; @@ -860,16 +858,19 @@ void pcie_setup_hoses(int busno) if (!yucca_pcie_card_present(i)) continue; -#ifdef PCIE_ENDPOINT - yucca_setup_pcie_fpga_endpoint(i); - if (ppc4xx_init_pcie_endport(i)) { -#else - yucca_setup_pcie_fpga_rootpoint(i); - if (ppc4xx_init_pcie_rootport(i)) { -#endif - printf("PCIE%d: initialization failed\n", i); - continue; + if (is_end_point(i)) { + printf("PCIE%d: will be configured as endpoint\n",i); + yucca_setup_pcie_fpga_endpoint(i); + ret = ppc4xx_init_pcie_endport(i); + } else { + printf("PCIE%d: will be configured as root-complex\n",i); + yucca_setup_pcie_fpga_rootpoint(i); + ret = ppc4xx_init_pcie_rootport(i); } + if (ret) { + printf("PCIE%d: initialization failed\n", i); + continue; + } hose = &pcie_hose[i]; hose->first_busno = bus; @@ -881,35 +882,33 @@ void pcie_setup_hoses(int busno) CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, CFG_PCIE_MEMSIZE, - PCI_REGION_MEM - ); + PCI_REGION_MEM); hose->region_count = 1; pci_register_hose(hose); -#ifdef PCIE_ENDPOINT - ppc4xx_setup_pcie_endpoint(hose, i); - /* - * Reson for no scanning is endpoint can not generate - * upstream configuration accesses. - */ -#else - ppc4xx_setup_pcie_rootpoint(hose, i); - - env = getenv ("pciscandelay"); - if (env != NULL) { - delay = simple_strtoul (env, NULL, 10); - if (delay > 5) - printf ("Warning, expect noticable delay before PCIe" - "scan due to 'pciscandelay' value!\n"); - mdelay (delay * 1000); - } + if (is_end_point(i)) { + ppc4xx_setup_pcie_endpoint(hose, i); + /* + * Reson for no scanning is endpoint can not generate + * upstream configuration accesses. + */ + } else { + ppc4xx_setup_pcie_rootpoint(hose, i); + env = getenv("pciscandelay"); + if (env != NULL) { + delay = simple_strtoul(env, NULL, 10); + if (delay > 5) + printf("Warning, expect noticable delay before " + "PCIe scan due to 'pciscandelay' value!\n"); + mdelay(delay * 1000); + } - /* - * Config access can only go down stream - */ - hose->last_busno = pci_hose_scan(hose); - bus = hose->last_busno + 1; -#endif + /* + * Config access can only go down stream + */ + hose->last_busno = pci_hose_scan(hose); + bus = hose->last_busno + 1; + } } } #endif /* defined(CONFIG_PCI) */ diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index 7ee0e5bc89d..9ab358857ad 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -46,6 +46,20 @@ enum { LNKW_X8 = 0x8 }; +static int validate_endpoint(struct pci_controller *hose) +{ + if (hose->cfg_data == (u8 *)CFG_PCIE0_CFGBASE) + return (is_end_point(0)); + else if (hose->cfg_data == (u8 *)CFG_PCIE1_CFGBASE) + return (is_end_point(1)); +#if CFG_PCIE_NR_PORTS > 2 + else if (hose->cfg_data == (u8 *)CFG_PCIE2_CFGBASE) + return (is_end_point(2)); +#endif + + return 0; +} + static u8* pcie_get_base(struct pci_controller *hose, unsigned int devfn) { u8 *base = (u8*)hose->cfg_data; @@ -95,6 +109,9 @@ static int pcie_read_config(struct pci_controller *hose, unsigned int devfn, u8 *address; *val = 0; + if (validate_endpoint(hose)) + return 0; /* No upstream config access */ + /* * Bus numbers are relative to hose->first_busno */ @@ -150,6 +167,9 @@ static int pcie_write_config(struct pci_controller *hose, unsigned int devfn, u8 *address; + if (validate_endpoint(hose)) + return 0; /* No upstream config access */ + /* * Bus numbers are relative to hose->first_busno */ @@ -595,9 +615,9 @@ int ppc4xx_init_pcie_port(int port, int rootport) u32 low, high; if (!core_init) { - ++core_init; if (ppc4xx_init_pcie()) return -1; + ++core_init; } /* diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index 17ac57b23bc..1830c6a8efd 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -244,6 +244,9 @@ #define U64_TO_U32_LOW(val) ((u32)((val) & 0x00000000ffffffffULL)) #define U64_TO_U32_HIGH(val) ((u32)((val) >> 32)) +/* + * Prototypes + */ int ppc4xx_init_pcie(void); int ppc4xx_init_pcie_rootport(int port); int ppc4xx_init_pcie_endport(int port); @@ -251,6 +254,55 @@ void ppc4xx_setup_pcie_rootpoint(struct pci_controller *hose, int port); int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port); int pcie_hose_scan(struct pci_controller *hose, int bus); +/* + * Function to determine root port or endport from env variable. + */ +static inline int is_end_point(int port) +{ + static char s[10], *tk; + + strcpy(s, getenv("pcie_mode")); + tk = strtok(s, ":"); + + switch (port) { + case 0: + if (tk != NULL) { + if (!(strcmp(tk, "ep") && strcmp(tk, "EP"))) + return 1; + else + return 0; + } + else + return 0; + + case 1: + tk = strtok(NULL, ":"); + if (tk != NULL) { + if (!(strcmp(tk, "ep") && strcmp(tk, "EP"))) + return 1; + else + return 0; + } + else + return 0; + + case 2: + tk = strtok(NULL, ":"); + if (tk != NULL) + tk = strtok(NULL, ":"); + if (tk != NULL) { + if (!(strcmp(tk, "ep") && strcmp(tk, "EP"))) + return 1; + else + return 0; + } + else + return 0; + } + + return 0; +} + static inline void mdelay(int n) { u32 ms = n; diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 8a963279f08..cccfc1316d5 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -205,6 +205,7 @@ "upd=run load;run update\0" \ "kozio=bootm ffc60000\0" \ "pciconfighost=1\0" \ + "pcie_mode=RP:RP:RP\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 461f8f0591d..f5e20235f74 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -205,6 +205,7 @@ "setenv filesize;saveenv\0" \ "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ + "pcie_mode=RP:RP\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" diff --git a/include/configs/yucca.h b/include/configs/yucca.h index ab7fb0ab8c2..2b4024dfd97 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -186,6 +186,7 @@ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ "pciconfighost=1\0" \ + "pcie_mode=RP:EP:EP\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -- cgit v1.3.1 From 5cb4af4791f61843432155142b6cfac901f66c10 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 18 Oct 2007 07:39:38 +0200 Subject: ppc4xx: Add PCIe endpoint support on Kilauea (405EX) This patch adds endpoint support for the AMCC Kilauea eval board. It can be tested by connecting a reworked PCIe cable (only 1x lane singles connected) to another root-complex. In this test setup, a 64MB inbound window is configured at BAR0 which maps to 0 on the PLB side. So accessing this BAR0 from the root-complex will access the first 64MB of the SDRAM on the PPC side. Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_pcie.c | 31 +++++++++++++++++++++---------- include/asm-ppc/4xx_pcie.h | 11 ++++++++--- 2 files changed, 29 insertions(+), 13 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index 9ab358857ad..da179f9c3a8 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -474,12 +474,6 @@ int __ppc4xx_init_pcie_port_hw(int port, int rootport) { u32 val; - /* - * test-only: - * This needs some testing and perhaps changes for - * endpoint configuration. Probably no PHY reset at all, etc. - * sr, 2007-10-03 - */ if (rootport) val = 0x00401000; else @@ -496,7 +490,10 @@ int __ppc4xx_init_pcie_port_hw(int port, int rootport) udelay(1000); /* deassert the PE0_hotreset */ - SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x01101000); + if (is_end_point(port)) + SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x01111000); + else + SDR_WRITE(SDRN_PESDR_RCSSET(port), 0x01101000); /* poll for phy !reset */ while (!(SDR_READ(SDRN_PESDR_PHYSTA(port)) & 0x00001000)) @@ -903,11 +900,22 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) #endif } - /* Set up 16GB inbound memory window at 0 */ + /* Set up 64MB inbound memory window at 0 */ out_le32(mbase + PCI_BASE_ADDRESS_0, 0); out_le32(mbase + PCI_BASE_ADDRESS_1, 0); - out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffc); - out_le32(mbase + PECFG_BAR0LMPA, 0); + + out_le32(mbase + PECFG_PIM01SAH, 0xffffffff); + out_le32(mbase + PECFG_PIM01SAL, 0xfc000000); + + /* Setup BAR0 */ + out_le32(mbase + PECFG_BAR0HMPA, 0x7fffffff); + out_le32(mbase + PECFG_BAR0LMPA, 0xfc000000 | PCI_BASE_ADDRESS_MEM_TYPE_64); + + /* Disable BAR1 & BAR2 */ + out_le32(mbase + PECFG_BAR1MPA, 0); + out_le32(mbase + PECFG_BAR2HMPA, 0); + out_le32(mbase + PECFG_BAR2LMPA, 0); + out_le32(mbase + PECFG_PIM0LAL, U64_TO_U32_LOW(CFG_PCIE_INBOUND_BASE)); out_le32(mbase + PECFG_PIM0LAH, U64_TO_U32_HIGH(CFG_PCIE_INBOUND_BASE)); out_le32(mbase + PECFG_PIMEN, 0x1); @@ -919,6 +927,9 @@ int ppc4xx_setup_pcie_endpoint(struct pci_controller *hose, int port) out_le16(mbase + 0x200, 0xcaad); /* Setting vendor ID */ out_le16(mbase + 0x202, 0xfeed); /* Setting device ID */ + /* Set Class Code to Processor/PPC */ + out_le32(mbase + 0x208, 0x0b200001); + attempts = 10; while(!(SDR_READ(SDRN_PESDR_RCSSTS(port)) & (1 << 8))) { if (!(attempts--)) { diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index 1830c6a8efd..ffe07706a31 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -218,7 +218,8 @@ #define PECFG_BAR0LMPA 0x210 #define PECFG_BAR0HMPA 0x214 #define PECFG_BAR1MPA 0x218 -#define PECFG_BAR2MPA 0x220 +#define PECFG_BAR2LMPA 0x220 +#define PECFG_BAR2HMPA 0x224 #define PECFG_PIMEN 0x33c #define PECFG_PIM0LAL 0x340 @@ -259,9 +260,13 @@ int pcie_hose_scan(struct pci_controller *hose, int bus); */ static inline int is_end_point(int port) { - static char s[10], *tk; + char s[10], *tk; + char *pcie_mode = getenv("pcie_mode"); - strcpy(s, getenv("pcie_mode")); + if (pcie_mode == NULL) + return 0; + + strcpy(s, pcie_mode); tk = strtok(s, ":"); switch (port) { -- cgit v1.3.1 From c36c68160333ac5fe41ec3db12a728b7075b3912 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 18 Oct 2007 07:42:27 +0200 Subject: ppc4xx: Change inbound PCIe location for endpoint tests on Katmai On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which is the internal SRAM. Since I now ported and tested this endpoint mode on Kilauea successfully to map to 0 (SDRAM), I also changed this for Katmai. Yucca will stay at internal SRAM for now. Not sure if somebody relies on this setup. Signed-off-by: Stefan Roese --- include/configs/katmai.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/katmai.h b/include/configs/katmai.h index cccfc1316d5..6bc8d025ae0 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -73,7 +73,7 @@ #define CFG_PCIE2_XCFGBASE 0xc3002000 /* base address of inbound PCIe window */ -#define CFG_PCIE_INBOUND_BASE 0x0000000400000000ULL +#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE -- cgit v1.3.1 From f6ba9b56607d4b27550301c7c7f6b55b654fd62a Mon Sep 17 00:00:00 2001 From: Eugene O'Brien Date: Thu, 18 Oct 2007 17:29:04 +0200 Subject: ppc4xx: Define CONFIG_BOOKE for all PPC440 based processors CONFIG_BOOKE must be defined for PPC440 processors so that the proper SPR number is used to access system registers. Signed-off-by: Eugene O'Brien Signed-off-by: Stefan Roese --- include/asm-ppc/processor.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include') diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 451ee94f618..f58b38aace6 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -91,6 +91,11 @@ /* Special Purpose Registers (SPRNs)*/ +/* PPC440 Architecture is BOOK-E */ +#ifdef CONFIG_440 +#define CONFIG_BOOKE +#endif + #define SPRN_CDBCR 0x3D7 /* Cache Debug Control Register */ #define SPRN_CTR 0x009 /* Count Register */ #define SPRN_DABR 0x3F5 /* Data Address Breakpoint Register */ -- cgit v1.3.1 From 087dfdb79b5fd1ab99a26990c62a732c01a8c7f6 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sun, 21 Oct 2007 08:12:41 +0200 Subject: ppc4xx: Consolidate some of the 405 and 440 macros/structs into 4xx This patch moves some common 4xx macros and the PPC405_SYS_INFO/ PPC440_SYS_INFO structure into the common ppc4xx.h header. Lot's of other macros are good candidates to be consolidated this way in the future. Signed-off-by: Stefan Roese --- board/amcc/taishan/showinfo.c | 14 +++---- board/amcc/yucca/yucca.c | 6 --- board/lwmon5/sdram.c | 2 +- board/mpl/common/common_util.c | 2 +- board/netstal/hcu5/sdram.c | 2 +- board/xilinx/ml300/ml300.c | 2 +- cpu/ppc4xx/40x_spd_sdram.c | 2 +- cpu/ppc4xx/44x_spd_ddr.c | 6 +-- cpu/ppc4xx/44x_spd_ddr2.c | 27 ++++++------- cpu/ppc4xx/speed.c | 30 +++++++-------- include/common.h | 4 +- include/ppc405.h | 58 ---------------------------- include/ppc440.h | 87 ------------------------------------------ include/ppc4xx.h | 73 +++++++++++++++++++++++++++++++++-- 14 files changed, 113 insertions(+), 202 deletions(-) (limited to 'include') diff --git a/board/amcc/taishan/showinfo.c b/board/amcc/taishan/showinfo.c index 57b9d1c4218..040b8004dac 100644 --- a/board/amcc/taishan/showinfo.c +++ b/board/amcc/taishan/showinfo.c @@ -33,25 +33,25 @@ void show_reset_reg(void) /* read clock regsiter */ printf("===== Display reset and initialize register Start =========\n"); - mfclk(clk_pllc,reg); + mfcpr(clk_pllc,reg); printf("cpr_pllc = %#010x\n",reg); - mfclk(clk_plld,reg); + mfcpr(clk_plld,reg); printf("cpr_plld = %#010x\n",reg); - mfclk(clk_primad,reg); + mfcpr(clk_primad,reg); printf("cpr_primad = %#010x\n",reg); - mfclk(clk_primbd,reg); + mfcpr(clk_primbd,reg); printf("cpr_primbd = %#010x\n",reg); - mfclk(clk_opbd,reg); + mfcpr(clk_opbd,reg); printf("cpr_opbd = %#010x\n",reg); - mfclk(clk_perd,reg); + mfcpr(clk_perd,reg); printf("cpr_perd = %#010x\n",reg); - mfclk(clk_mald,reg); + mfcpr(clk_mald,reg); printf("cpr_mald = %#010x\n",reg); /* read sdr register */ diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index efdf814bf08..bb3e59400f0 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -36,13 +36,7 @@ DECLARE_GLOBAL_DATA_PTR; - void fpga_init (void); -void get_sys_info(PPC440_SYS_INFO *board_cfg ); -int compare_to_true(char *str ); -char *remove_l_w_space(char *in_str ); -char *remove_t_w_space(char *in_str ); -int get_console_port(void); #define DEBUG_ENV #ifdef DEBUG_ENV diff --git a/board/lwmon5/sdram.c b/board/lwmon5/sdram.c index d4547e24cf1..399da8ae654 100644 --- a/board/lwmon5/sdram.c +++ b/board/lwmon5/sdram.c @@ -71,7 +71,7 @@ static u32 is_ecc_enabled(void) void board_add_ram_info(int use_default) { - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; u32 val; if (is_ecc_enabled()) diff --git a/board/mpl/common/common_util.c b/board/mpl/common/common_util.c index f3aa0a73007..8d4cbe852e9 100644 --- a/board/mpl/common/common_util.c +++ b/board/mpl/common/common_util.c @@ -587,7 +587,7 @@ extern int get_boot_mode(void); void video_get_info_str (int line_number, char *info) { /* init video info strings for graphic console */ - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; char rev; int i,boot; unsigned long pvr; diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c index 9ee9ab599b6..cbb2839cc02 100644 --- a/board/netstal/hcu5/sdram.c +++ b/board/netstal/hcu5/sdram.c @@ -72,7 +72,7 @@ void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value); void board_add_ram_info(int use_default) { - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; u32 val; mfsdram(DDR0_22, val); val &= DDR0_22_CTRL_RAW_MASK; diff --git a/board/xilinx/ml300/ml300.c b/board/xilinx/ml300/ml300.c index 60f0bc24e78..58bfac07166 100644 --- a/board/xilinx/ml300/ml300.c +++ b/board/xilinx/ml300/ml300.c @@ -108,7 +108,7 @@ ulong get_PCI_freq(void) { ulong val; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info(&sys_info); val = sys_info.freqPCI; diff --git a/cpu/ppc4xx/40x_spd_sdram.c b/cpu/ppc4xx/40x_spd_sdram.c index 19c4f764e39..42fd7fb872f 100644 --- a/cpu/ppc4xx/40x_spd_sdram.c +++ b/cpu/ppc4xx/40x_spd_sdram.c @@ -148,7 +148,7 @@ long int spd_sdram(int(read_spd)(uint addr)) int t_rc; int min_cas; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; unsigned long bus_period_x_10; /* diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index 4a4c6f29edf..65ce46daf34 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -645,7 +645,7 @@ static void program_rtr(unsigned long *dimm_populated, unsigned char refresh_rate_type; unsigned long refresh_interval; unsigned long sdram_rtr; - PPC440_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; /* * get the board info @@ -721,7 +721,7 @@ static void program_tr0(unsigned long *dimm_populated, unsigned long tcyc_2_0_ns_x_10; unsigned long tcyc_reg; unsigned long bus_period_x_10; - PPC440_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; unsigned long residue; /* @@ -1065,7 +1065,7 @@ static void program_tr1(void) unsigned char window_found; unsigned char fail_found; unsigned char pass_found; - PPC440_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; /* * get the board info diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index 67ba5bdef24..b3413671b51 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -623,7 +623,7 @@ static void get_spd_info(unsigned long *dimm_populated, void board_add_ram_info(int use_default) { - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; u32 val; if (is_ecc_enabled()) @@ -741,7 +741,7 @@ static void check_frequency(unsigned long *dimm_populated, unsigned long calc_cycle_time; unsigned long sdram_freq; unsigned long sdr_ddrpll; - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; /*------------------------------------------------------------------ * Get the board configuration info. @@ -1353,7 +1353,7 @@ static void program_mode(unsigned long *dimm_populated, unsigned long max_4_0_tcyc_ns_x_100; unsigned long max_5_0_tcyc_ns_x_100; unsigned long cycle_time_ns_x_100[3]; - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; unsigned char cas_2_0_available; unsigned char cas_2_5_available; unsigned char cas_3_0_available; @@ -1640,7 +1640,7 @@ static void program_rtr(unsigned long *dimm_populated, unsigned char *iic0_dimm_addr, unsigned long num_dimm_banks) { - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; unsigned long max_refresh_rate; unsigned long dimm_num; unsigned long refresh_rate_type; @@ -1737,7 +1737,7 @@ static void program_tr(unsigned long *dimm_populated, unsigned long sdram_freq; unsigned long sdr_ddrpll; - PPC440_SYS_INFO board_cfg; + PPC4xx_SYS_INFO board_cfg; /*------------------------------------------------------------------ * Get the board configuration info. @@ -2048,14 +2048,10 @@ static void program_bxcf(unsigned long *dimm_populated, /*------------------------------------------------------------------ * Set the BxCF regs. First, wipe out the bank config registers. *-----------------------------------------------------------------*/ - mtdcr(SDRAMC_CFGADDR, SDRAM_MB0CF); - mtdcr(SDRAMC_CFGDATA, 0x00000000); - mtdcr(SDRAMC_CFGADDR, SDRAM_MB1CF); - mtdcr(SDRAMC_CFGDATA, 0x00000000); - mtdcr(SDRAMC_CFGADDR, SDRAM_MB2CF); - mtdcr(SDRAMC_CFGDATA, 0x00000000); - mtdcr(SDRAMC_CFGADDR, SDRAM_MB3CF); - mtdcr(SDRAMC_CFGDATA, 0x00000000); + mtsdram(SDRAM_MB0CF, 0x00000000); + mtsdram(SDRAM_MB1CF, 0x00000000); + mtsdram(SDRAM_MB2CF, 0x00000000); + mtsdram(SDRAM_MB3CF, 0x00000000); mode = SDRAM_BXCF_M_BE_ENABLE; @@ -2107,8 +2103,9 @@ static void program_bxcf(unsigned long *dimm_populated, bank_0_populated = 1; for (ind_rank = 0; ind_rank < num_ranks; ind_rank++) { - mtdcr(SDRAMC_CFGADDR, SDRAM_MB0CF + ((dimm_num + bank_0_populated + ind_rank) << 2)); - mtdcr(SDRAMC_CFGDATA, mode); + mtsdram(SDRAM_MB0CF + + ((dimm_num + bank_0_populated + ind_rank) << 2), + mode); } } } diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c index 750b0958762..26182dabf01 100644 --- a/cpu/ppc4xx/speed.c +++ b/cpu/ppc4xx/speed.c @@ -37,7 +37,7 @@ DECLARE_GLOBAL_DATA_PTR; #if defined(CONFIG_405GP) || defined(CONFIG_405CR) -void get_sys_info (PPC405_SYS_INFO * sysInfo) +void get_sys_info (PPC4xx_SYS_INFO * sysInfo) { unsigned long pllmr; unsigned long sysClkPeriodPs = ONE_BILLION / (CONFIG_SYS_CLK_FREQ / 1000); @@ -173,7 +173,7 @@ ulong get_OPB_freq (void) { ulong val = 0; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = sys_info.freqPLB / sys_info.pllOpbDiv; @@ -189,7 +189,7 @@ ulong get_OPB_freq (void) ulong get_PCI_freq (void) { ulong val; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = sys_info.freqPLB / sys_info.pllPciDiv; @@ -216,7 +216,7 @@ void get_sys_info (sys_info_t *sysInfo) */ /* Decode CPR0_PLLD0 for divisors */ - mfclk(clk_plld, reg); + mfcpr(clk_plld, reg); temp = (reg & PLLD_FWDVA_MASK) >> 16; sysInfo->pllFwdDivA = temp ? temp : 16; temp = (reg & PLLD_FWDVB_MASK) >> 8; @@ -225,19 +225,19 @@ void get_sys_info (sys_info_t *sysInfo) sysInfo->pllFbkDiv = temp ? temp : 32; lfdiv = reg & PLLD_LFBDV_MASK; - mfclk(clk_opbd, reg); + mfcpr(clk_opbd, reg); temp = (reg & OPBDDV_MASK) >> 24; sysInfo->pllOpbDiv = temp ? temp : 4; - mfclk(clk_perd, reg); + mfcpr(clk_perd, reg); temp = (reg & PERDV_MASK) >> 24; sysInfo->pllExtBusDiv = temp ? temp : 8; - mfclk(clk_primbd, reg); + mfcpr(clk_primbd, reg); temp = (reg & PRBDV_MASK) >> 24; prbdv0 = temp ? temp : 8; - mfclk(clk_spcid, reg); + mfcpr(clk_spcid, reg); temp = (reg & SPCID_MASK) >> 24; sysInfo->pllPciDiv = temp ? temp : 4; @@ -246,7 +246,7 @@ void get_sys_info (sys_info_t *sysInfo) temp = (reg & PLLSYS0_SEL_MASK) >> 27; if (temp == 0) { /* PLL output */ /* Figure which pll to use */ - mfclk(clk_pllc, reg); + mfcpr(clk_pllc, reg); temp = (reg & PLLC_SRC_MASK) >> 29; if (!temp) /* PLLOUTA */ m = sysInfo->pllFbkDiv * lfdiv * sysInfo->pllFwdDivA; @@ -650,7 +650,7 @@ void get_sys_info (sys_info_t * sysInfo) { } #elif defined(CONFIG_405EP) -void get_sys_info (PPC405_SYS_INFO * sysInfo) +void get_sys_info (PPC4xx_SYS_INFO * sysInfo) { unsigned long pllmr0; unsigned long pllmr1; @@ -746,7 +746,7 @@ ulong get_OPB_freq (void) { ulong val = 0; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = sys_info.freqPLB / sys_info.pllOpbDiv; @@ -762,7 +762,7 @@ ulong get_OPB_freq (void) ulong get_PCI_freq (void) { ulong val; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = sys_info.freqPLB / sys_info.pllPciDiv; @@ -770,7 +770,7 @@ ulong get_PCI_freq (void) } #elif defined(CONFIG_405EZ) -void get_sys_info (PPC405_SYS_INFO * sysInfo) +void get_sys_info (PPC4xx_SYS_INFO * sysInfo) { unsigned long cpr_plld; unsigned long cpr_pllc; @@ -871,7 +871,7 @@ ulong get_OPB_freq (void) { ulong val = 0; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = (CONFIG_SYS_CLK_FREQ * sys_info.pllFbkDiv) / sys_info.pllOpbDiv; @@ -1032,7 +1032,7 @@ ulong get_OPB_freq (void) { ulong val = 0; - PPC405_SYS_INFO sys_info; + PPC4xx_SYS_INFO sys_info; get_sys_info (&sys_info); val = sys_info.freqPLB / sys_info.pllOpbDiv; diff --git a/include/common.h b/include/common.h index 98655914f72..46ed6bd97b3 100644 --- a/include/common.h +++ b/include/common.h @@ -513,15 +513,13 @@ void get_sys_info ( sys_info_t * ); #if defined(CONFIG_4xx) || defined(CONFIG_IOP480) # if defined(CONFIG_440) - typedef PPC440_SYS_INFO sys_info_t; # if defined(CONFIG_440SPE) unsigned long determine_sysper(void); unsigned long determine_pci_clock_per(void); int ppc440spe_revB(void); # endif -# else - typedef PPC405_SYS_INFO sys_info_t; # endif +typedef PPC4xx_SYS_INFO sys_info_t; void get_sys_info ( sys_info_t * ); #endif diff --git a/include/ppc405.h b/include/ppc405.h index 4d2514425e2..97528e88a82 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -344,9 +344,6 @@ /****************************************************************************** * SDRAM Controller ******************************************************************************/ -#define SDRAM_DCR_BASE 0x10 -#define memcfga (SDRAM_DCR_BASE+0x0) /* Memory configuration address reg */ -#define memcfgd (SDRAM_DCR_BASE+0x1) /* Memory configuration data reg */ /* values for memcfga register - indirect addressing of these regs */ #ifndef CONFIG_405EP #define mem_besra 0x00 /* bus error syndrome reg a */ @@ -412,9 +409,6 @@ /****************************************************************************** * Extrnal Bus Controller ******************************************************************************/ -#define EBC_DCR_BASE 0x12 -#define ebccfga (EBC_DCR_BASE+0x0) /* External bus controller addr reg */ -#define ebccfgd (EBC_DCR_BASE+0x1) /* External bus controller data reg */ /* values for ebccfga register - indirect addressing of these regs */ #define pb0cr 0x00 /* periph bank 0 config reg */ #define pb1cr 0x01 /* periph bank 1 config reg */ @@ -1574,56 +1568,4 @@ #define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ #endif -/****************************************************************************** - * SDR Registers - ******************************************************************************/ -#define SDR_DCR_BASE 0x0E -#define sdrcfga (SDR_DCR_BASE+0x0) -#define sdrcfgd (SDR_DCR_BASE+0x1) - -#define CPR0_DCR_BASE 0x0C -#define cprcfga (CPR0_DCR_BASE+0x0) -#define cprcfgd (CPR0_DCR_BASE+0x1) - -#define mtcpr(reg, d) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,d); } while (0) -#define mfcpr(reg, d) do { mtdcr(cprcfga,reg);d = mfdcr(cprcfgd); } while (0) - -#define mtsdr(reg, d) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,d); } while (0) -#define mfsdr(reg, d) do { mtdcr(sdrcfga,reg);d = mfdcr(sdrcfgd); } while (0) - -#define mtebc(reg, d) do { mtdcr(ebccfga,reg);mtdcr(ebccfgd,d); } while (0) -#define mfebc(reg, d) do { mtdcr(ebccfga,reg);d = mfdcr(ebccfgd); } while (0) - -#define mtsdram(reg, d) do { mtdcr(memcfga,reg);mtdcr(memcfgd,d); } while (0) -#define mfsdram(reg, d) do { mtdcr(memcfga,reg);d = mfdcr(memcfgd); } while (0) - -#ifndef __ASSEMBLY__ - -typedef struct -{ - unsigned long pllFwdDiv; - unsigned long pllFwdDivB; - unsigned long pllFbkDiv; - unsigned long pllPlbDiv; - unsigned long pllPciDiv; - unsigned long pllExtBusDiv; - unsigned long pllOpbDiv; - unsigned long freqVCOMhz; /* in MHz */ - unsigned long freqProcessor; - unsigned long freqPLB; - unsigned long freqPCI; - unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */ - unsigned long pciClkSync; /* PCI clock is synchronous */ - unsigned long freqVCOHz; - unsigned long freqOPB; - unsigned long freqEBC; - unsigned long freqDDR; -} PPC405_SYS_INFO; - -#endif /* _ASMLANGUAGE */ - -#define RESET_VECTOR 0xfffffffc -#define CACHELINE_MASK (CFG_CACHELINE_SIZE - 1) /* Address mask for cache - line aligned data. */ - #endif /* __PPC405_H__ */ diff --git a/include/ppc440.h b/include/ppc440.h index e77c4c3fb66..dc5eb98c909 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -123,10 +123,6 @@ /*----------------------------------------------------------------------------- | Clocking Controller +----------------------------------------------------------------------------*/ -#define CLOCKING_DCR_BASE 0x0c -#define clkcfga (CLOCKING_DCR_BASE+0x0) -#define clkcfgd (CLOCKING_DCR_BASE+0x1) - /* values for clkcfga register - indirect addressing of these regs */ #define clk_clkukpd 0x0020 #define clk_pllc 0x0040 @@ -140,9 +136,6 @@ #define clk_icfg 0x0140 /* 440gx sdr register definations */ -#define SDR_DCR_BASE 0x0e -#define sdrcfga (SDR_DCR_BASE+0x0) -#define sdrcfgd (SDR_DCR_BASE+0x1) #define sdr_sdstp0 0x0020 /* */ #define sdr_sdstp1 0x0021 /* */ #define SDR_PINSTP 0x0040 @@ -242,10 +235,6 @@ /*----------------------------------------------------------------------------- | SDRAM Controller +----------------------------------------------------------------------------*/ -#define SDRAM_DCR_BASE 0x10 -#define memcfga (SDRAM_DCR_BASE+0x0) /* Memory configuration address reg */ -#define memcfgd (SDRAM_DCR_BASE+0x1) /* Memory configuration data reg */ - /* values for memcfga register - indirect addressing of these regs */ #define mem_besr0_clr 0x0000 /* bus error status reg 0 (clr) */ #define mem_besr0_set 0x0004 /* bus error status reg 0 (set) */ @@ -331,9 +320,6 @@ #define sdr_sdstp6 0x4005 #define sdr_sdstp7 0x4007 -#define SDR0_CFGADDR 0x00E -#define SDR0_CFGDATA 0x00F - /****************************************************************************** * PCI express defines ******************************************************************************/ @@ -480,10 +466,6 @@ /*----------------------------------------------------------------------------+ | Memory controller defines +----------------------------------------------------------------------------*/ -#define SDRAMC_DCR_BASE 0x010 -#define SDRAMC_CFGADDR (SDRAMC_DCR_BASE+0x0) /* Memory configuration add */ -#define SDRAMC_CFGDATA (SDRAMC_DCR_BASE+0x1) /* Memory configuration data */ - /* A REVOIR versus specs 4 bank - SG*/ #define SDRAM_MCSTAT 0x14 /* memory controller status */ #define SDRAM_MCOPT1 0x20 /* memory controller options 1 */ @@ -834,9 +816,6 @@ /*----------------------------------------------------------------------------- | External Bus Controller +----------------------------------------------------------------------------*/ -#define EBC_DCR_BASE 0x12 -#define ebccfga (EBC_DCR_BASE+0x0) /* External bus controller addr reg */ -#define ebccfgd (EBC_DCR_BASE+0x1) /* External bus controller data reg */ /* values for ebccfga register - indirect addressing of these regs */ #define pb0cr 0x00 /* periph bank 0 config reg */ #define pb1cr 0x01 /* periph bank 1 config reg */ @@ -2207,9 +2186,6 @@ #define SDR0_CP440_NTO1_NTO1 0x00000002 #define SDR0_CP440_NTO1_ENCODE(n) ((((unsigned long)(n))&0x01)<<1) #define SDR0_CP440_NTO1_DECODE(n) ((((unsigned long)(n))>>1)&0x01) -#define SDR0_CFGADDR 0x00E /*already defined line 277 */ -#define SDR0_CFGDATA 0x00F - #define SDR0_SDSTP0 0x0020 #define SDR0_SDSTP0_ENG_MASK 0x80000000 @@ -3289,71 +3265,8 @@ #define GPIO1_ISR3H (GPIO1_BASE+0x44) #endif -/* - * Macros for accessing the indirect EBC registers - */ -#define mtebc(reg, data) do { mtdcr(ebccfga,reg);mtdcr(ebccfgd,data); } while (0) -#define mfebc(reg, data) do { mtdcr(ebccfga,reg);data = mfdcr(ebccfgd); } while (0) - -/* - * Macros for accessing the indirect SDRAM controller registers - */ -#define mtsdram(reg, data) do { mtdcr(memcfga,reg);mtdcr(memcfgd,data); } while (0) -#define mfsdram(reg, data) do { mtdcr(memcfga,reg);data = mfdcr(memcfgd); } while (0) - -/* - * Macros for accessing the indirect clocking controller registers - */ -#define mtclk(reg, data) do { mtdcr(clkcfga,reg);mtdcr(clkcfgd,data); } while (0) -#define mfclk(reg, data) do { mtdcr(clkcfga,reg);data = mfdcr(clkcfgd); } while (0) - -/* - * Macros for accessing the sdr controller registers - */ -#define mtsdr(reg, data) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,data); } while (0) -#define mfsdr(reg, data) do { mtdcr(sdrcfga,reg);data = mfdcr(sdrcfgd); } while (0) - -/* - * All 44x except 440GP have CPR registers (indirect DCR) - */ -#if !defined(CONFIG_440GP) -#define CPR0_CFGADDR 0x00C -#define CPR0_CFGDATA 0x00D - -#define mtcpr(reg, data) do { \ - mtdcr(CPR0_CFGADDR, reg); \ - mtdcr(CPR0_CFGDATA, data); \ - } while (0) - -#define mfcpr(reg, data) do { \ - mtdcr(CPR0_CFGADDR, reg); \ - data = mfdcr(CPR0_CFGDATA); \ - } while (0) -#endif - #ifndef __ASSEMBLY__ -typedef struct { - unsigned long pllFwdDivA; - unsigned long pllFwdDivB; - unsigned long pllFbkDiv; - unsigned long pllOpbDiv; - unsigned long pllPciDiv; - unsigned long pllExtBusDiv; - unsigned long freqVCOMhz; /* in MHz */ - unsigned long freqProcessor; - unsigned long freqTmrClk; - unsigned long freqPLB; - unsigned long freqOPB; - unsigned long freqEBC; - unsigned long freqPCI; -#ifdef CONFIG_440SPE - unsigned long freqDDR; -#endif - unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */ - unsigned long pciClkSync; /* PCI clock is synchronous */ -} PPC440_SYS_INFO; - static inline u32 get_mcsr(void) { u32 val; diff --git a/include/ppc4xx.h b/include/ppc4xx.h index ca241d2c13c..76fe8727f56 100644 --- a/include/ppc4xx.h +++ b/include/ppc4xx.h @@ -22,13 +22,80 @@ #ifndef __PPC4XX_H__ #define __PPC4XX_H__ -#define EXC_OFF_SYS_RESET 0x0100 /* System reset */ -#define _START_OFFSET (EXC_OFF_SYS_RESET + 0x2000) - #if defined(CONFIG_440) #include #else #include #endif +/* + * Common stuff for 4xx (405 and 440) + */ + +#define EXC_OFF_SYS_RESET 0x0100 /* System reset */ +#define _START_OFFSET (EXC_OFF_SYS_RESET + 0x2000) + +#define RESET_VECTOR 0xfffffffc +#define CACHELINE_MASK (CFG_CACHELINE_SIZE - 1) /* Address mask for cache + line aligned data. */ + +#define CPR0_DCR_BASE 0x0C +#define cprcfga (CPR0_DCR_BASE+0x0) +#define cprcfgd (CPR0_DCR_BASE+0x1) + +#define SDR_DCR_BASE 0x0E +#define sdrcfga (SDR_DCR_BASE+0x0) +#define sdrcfgd (SDR_DCR_BASE+0x1) + +#define SDRAM_DCR_BASE 0x10 +#define memcfga (SDRAM_DCR_BASE+0x0) +#define memcfgd (SDRAM_DCR_BASE+0x1) + +#define EBC_DCR_BASE 0x12 +#define ebccfga (EBC_DCR_BASE+0x0) +#define ebccfgd (EBC_DCR_BASE+0x1) + +/* + * Macros for indirect DCR access + */ +#define mtcpr(reg, d) do { mtdcr(cprcfga,reg);mtdcr(cprcfgd,d); } while (0) +#define mfcpr(reg, d) do { mtdcr(cprcfga,reg);d = mfdcr(cprcfgd); } while (0) + +#define mtebc(reg, d) do { mtdcr(ebccfga,reg);mtdcr(ebccfgd,d); } while (0) +#define mfebc(reg, d) do { mtdcr(ebccfga,reg);d = mfdcr(ebccfgd); } while (0) + +#define mtsdram(reg, d) do { mtdcr(memcfga,reg);mtdcr(memcfgd,d); } while (0) +#define mfsdram(reg, d) do { mtdcr(memcfga,reg);d = mfdcr(memcfgd); } while (0) + +#define mtsdr(reg, d) do { mtdcr(sdrcfga,reg);mtdcr(sdrcfgd,d); } while (0) +#define mfsdr(reg, d) do { mtdcr(sdrcfga,reg);d = mfdcr(sdrcfgd); } while (0) + +#ifndef __ASSEMBLY__ + +typedef struct +{ + unsigned long freqDDR; + unsigned long freqEBC; + unsigned long freqOPB; + unsigned long freqPCI; + unsigned long freqPLB; + unsigned long freqTmrClk; + unsigned long freqUART; + unsigned long freqProcessor; + unsigned long freqVCOHz; + unsigned long freqVCOMhz; /* in MHz */ + unsigned long pciClkSync; /* PCI clock is synchronous */ + unsigned long pciIntArbEn; /* Internal PCI arbiter is enabled */ + unsigned long pllExtBusDiv; + unsigned long pllFbkDiv; + unsigned long pllFwdDiv; + unsigned long pllFwdDivA; + unsigned long pllFwdDivB; + unsigned long pllOpbDiv; + unsigned long pllPciDiv; + unsigned long pllPlbDiv; +} PPC4xx_SYS_INFO; + +#endif /* __ASSEMBLY__ */ + #endif /* __PPC4XX_H__ */ -- cgit v1.3.1 From 758c037aeead34b49631b8da3a90b1bba14c0410 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sun, 21 Oct 2007 08:16:12 +0200 Subject: rtc: Add Xicor/Intersil X1205 RTC support This patch adds support for the Xicor/Intersil X1205 RTC used on the AMCC Makalu eval board. This driver is basically cloned from the Linux driver version (2.6.23). This patch also introduces the Linux bcd.h header for the BCD2BIN/ BIN2BCD conversions. In the future some of the other U-Boot RTC driver should be converted to also use this header instead of implementing their own local copy of these functions/macros. Signed-off-by: Stefan Roese --- include/bcd.h | 20 +++++++ rtc/Makefile | 2 +- rtc/x1205.c | 178 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 199 insertions(+), 1 deletion(-) create mode 100644 include/bcd.h create mode 100644 rtc/x1205.c (limited to 'include') diff --git a/include/bcd.h b/include/bcd.h new file mode 100644 index 00000000000..c545308125b --- /dev/null +++ b/include/bcd.h @@ -0,0 +1,20 @@ +/* Permission is hereby granted to copy, modify and redistribute this code + * in terms of the GNU Library General Public License, Version 2 or later, + * at your option. + */ + +/* macros to translate to/from binary and binary-coded decimal (frequently + * found in RTC chips). + */ + +#ifndef _BCD_H +#define _BCD_H + +#define BCD2BIN(val) (((val) & 0x0f) + ((val)>>4)*10) +#define BIN2BCD(val) ((((val)/10)<<4) + (val)%10) + +/* backwards compat */ +#define BCD_TO_BIN(val) ((val)=BCD2BIN(val)) +#define BIN_TO_BCD(val) ((val)=BIN2BCD(val)) + +#endif /* _BCD_H */ diff --git a/rtc/Makefile b/rtc/Makefile index 2e6f3bdddf0..5a0cf113a5c 100644 --- a/rtc/Makefile +++ b/rtc/Makefile @@ -32,7 +32,7 @@ COBJS = date.o \ ds1337.o ds1374.o ds1556.o ds164x.o ds174x.o ds3231.o \ m41t11.o max6900.o m48t35ax.o mc146818.o mk48t59.o \ mpc5xxx.o mpc8xx.o pcf8563.o s3c24x0_rtc.o rs5c372.o \ - mcfrtc.o + mcfrtc.o x1205.o SRCS := $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/rtc/x1205.c b/rtc/x1205.c new file mode 100644 index 00000000000..319f0512ca8 --- /dev/null +++ b/rtc/x1205.c @@ -0,0 +1,178 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * based on a the Linux rtc-x1207.c driver which is: + * Copyright 2004 Karen Spearel + * Copyright 2005 Alessandro Zummo + * + * Information and datasheet: + * http://www.intersil.com/cda/deviceinfo/0,1477,X1205,00.html + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Date & Time support for Xicor/Intersil X1205 RTC + */ + +/* #define DEBUG */ + +#include +#include +#include +#include +#include + +#if defined(CONFIG_RTC_X1205) && defined(CONFIG_CMD_DATE) + +#define CCR_SEC 0 +#define CCR_MIN 1 +#define CCR_HOUR 2 +#define CCR_MDAY 3 +#define CCR_MONTH 4 +#define CCR_YEAR 5 +#define CCR_WDAY 6 +#define CCR_Y2K 7 + +#define X1205_REG_SR 0x3F /* status register */ +#define X1205_REG_Y2K 0x37 +#define X1205_REG_DW 0x36 +#define X1205_REG_YR 0x35 +#define X1205_REG_MO 0x34 +#define X1205_REG_DT 0x33 +#define X1205_REG_HR 0x32 +#define X1205_REG_MN 0x31 +#define X1205_REG_SC 0x30 +#define X1205_REG_DTR 0x13 +#define X1205_REG_ATR 0x12 +#define X1205_REG_INT 0x11 +#define X1205_REG_0 0x10 +#define X1205_REG_Y2K1 0x0F +#define X1205_REG_DWA1 0x0E +#define X1205_REG_YRA1 0x0D +#define X1205_REG_MOA1 0x0C +#define X1205_REG_DTA1 0x0B +#define X1205_REG_HRA1 0x0A +#define X1205_REG_MNA1 0x09 +#define X1205_REG_SCA1 0x08 +#define X1205_REG_Y2K0 0x07 +#define X1205_REG_DWA0 0x06 +#define X1205_REG_YRA0 0x05 +#define X1205_REG_MOA0 0x04 +#define X1205_REG_DTA0 0x03 +#define X1205_REG_HRA0 0x02 +#define X1205_REG_MNA0 0x01 +#define X1205_REG_SCA0 0x00 + +#define X1205_CCR_BASE 0x30 /* Base address of CCR */ +#define X1205_ALM0_BASE 0x00 /* Base address of ALARM0 */ + +#define X1205_SR_RTCF 0x01 /* Clock failure */ +#define X1205_SR_WEL 0x02 /* Write Enable Latch */ +#define X1205_SR_RWEL 0x04 /* Register Write Enable */ + +#define X1205_DTR_DTR0 0x01 +#define X1205_DTR_DTR1 0x02 +#define X1205_DTR_DTR2 0x04 + +#define X1205_HR_MIL 0x80 /* Set in ccr.hour for 24 hr mode */ + +static void rtc_write(int reg, u8 val) +{ + i2c_write(CFG_I2C_RTC_ADDR, reg, 2, &val, 1); +} + +/* + * In the routines that deal directly with the x1205 hardware, we use + * rtc_time -- month 0-11, hour 0-23, yr = calendar year-epoch + * Epoch is initialized as 2000. Time is set to UTC. + */ +void rtc_get(struct rtc_time *tm) +{ + u8 buf[8]; + + i2c_read(CFG_I2C_RTC_ADDR, X1205_CCR_BASE, 2, buf, 8); + + debug("%s: raw read data - sec=%02x, min=%02x, hr=%02x, " + "mday=%02x, mon=%02x, year=%02x, wday=%02x, y2k=%02x\n", + __FUNCTION__, + buf[0], buf[1], buf[2], buf[3], + buf[4], buf[5], buf[6], buf[7]); + + tm->tm_sec = BCD2BIN(buf[CCR_SEC]); + tm->tm_min = BCD2BIN(buf[CCR_MIN]); + tm->tm_hour = BCD2BIN(buf[CCR_HOUR] & 0x3F); /* hr is 0-23 */ + tm->tm_mday = BCD2BIN(buf[CCR_MDAY]); + tm->tm_mon = BCD2BIN(buf[CCR_MONTH]); /* mon is 0-11 */ + tm->tm_year = BCD2BIN(buf[CCR_YEAR]) + + (BCD2BIN(buf[CCR_Y2K]) * 100); + tm->tm_wday = buf[CCR_WDAY]; + + debug("%s: tm is secs=%d, mins=%d, hours=%d, " + "mday=%d, mon=%d, year=%d, wday=%d\n", + __FUNCTION__, + tm->tm_sec, tm->tm_min, tm->tm_hour, + tm->tm_mday, tm->tm_mon, tm->tm_year, tm->tm_wday); +} + +void rtc_set(struct rtc_time *tm) +{ + int i; + u8 buf[8]; + + debug("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n", + tm->tm_year, tm->tm_mon, tm->tm_mday, tm->tm_wday, + tm->tm_hour, tm->tm_min, tm->tm_sec); + + buf[CCR_SEC] = BIN2BCD(tm->tm_sec); + buf[CCR_MIN] = BIN2BCD(tm->tm_min); + + /* set hour and 24hr bit */ + buf[CCR_HOUR] = BIN2BCD(tm->tm_hour) | X1205_HR_MIL; + + buf[CCR_MDAY] = BIN2BCD(tm->tm_mday); + + /* month, 1 - 12 */ + buf[CCR_MONTH] = BIN2BCD(tm->tm_mon); + + /* year, since the rtc epoch*/ + buf[CCR_YEAR] = BIN2BCD(tm->tm_year % 100); + buf[CCR_WDAY] = tm->tm_wday & 0x07; + buf[CCR_Y2K] = BIN2BCD(tm->tm_year / 100); + + /* this sequence is required to unlock the chip */ + rtc_write(X1205_REG_SR, X1205_SR_WEL); + rtc_write(X1205_REG_SR, X1205_SR_WEL | X1205_SR_RWEL); + + /* write register's data */ + for (i = 0; i < 8; i++) + rtc_write(X1205_CCR_BASE + i, buf[i]); + + rtc_write(X1205_REG_SR, 0); +} + +void rtc_reset(void) +{ + /* + * Nothing to do + */ +} + +#endif -- cgit v1.3.1 From 837c730b4d7c6b1ddf3d1e247cb4445005d9bf0d Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sun, 21 Oct 2007 14:26:29 +0200 Subject: ppc: Small Kilauea cleanup of config file Signed-off-by: Stefan Roese --- include/configs/kilauea.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index f5e20235f74..74c94830c22 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -438,10 +438,10 @@ #define CFG_FPGA_USER_LED0 0x00000200 #define CFG_FPGA_USER_LED1 0x00000100 -#endif /* __CONFIG_H */ - /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define OF_CPU "PowerPC,405EX@0" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 211ea91ac6c225bec7e668a03d0ba7d7310679fa Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 22 Oct 2007 07:34:34 +0200 Subject: ppc4xx: Add initial AMCC Makalu 405EX support Signed-off-by: Stefan Roese --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + board/amcc/makalu/Makefile | 50 ++++++ board/amcc/makalu/cmd_pll.c | 297 +++++++++++++++++++++++++++++++++ board/amcc/makalu/config.mk | 24 +++ board/amcc/makalu/init.S | 154 +++++++++++++++++ board/amcc/makalu/makalu.c | 378 ++++++++++++++++++++++++++++++++++++++++++ board/amcc/makalu/memory.c | 188 +++++++++++++++++++++ board/amcc/makalu/u-boot.lds | 137 +++++++++++++++ include/configs/makalu.h | 387 +++++++++++++++++++++++++++++++++++++++++++ 11 files changed, 1620 insertions(+) create mode 100644 board/amcc/makalu/Makefile create mode 100644 board/amcc/makalu/cmd_pll.c create mode 100644 board/amcc/makalu/config.mk create mode 100644 board/amcc/makalu/init.S create mode 100644 board/amcc/makalu/makalu.c create mode 100644 board/amcc/makalu/memory.c create mode 100644 board/amcc/makalu/u-boot.lds create mode 100644 include/configs/makalu.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 9ec7a5c24fd..5ae588f6644 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -306,6 +306,7 @@ Stefan Roese katmai PPC440SPe kilauea PPC405EX lwmon5 PPC440EPx + makalu PPC405EX ocotea PPC440GX p3p440 PPC440GP pcs440ep PPC440EP diff --git a/MAKEALL b/MAKEALL index 83c498c219a..874d3a6710d 100755 --- a/MAKEALL +++ b/MAKEALL @@ -190,6 +190,7 @@ LIST_4xx=" \ kilauea \ luan \ lwmon5 \ + makalu \ METROBOX \ MIP405 \ MIP405T \ diff --git a/Makefile b/Makefile index ba96ca1de37..039cec08f76 100644 --- a/Makefile +++ b/Makefile @@ -1177,6 +1177,9 @@ luan_config: unconfig lwmon5_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx lwmon5 +makalu_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx makalu amcc + METROBOX_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx metrobox sandburst diff --git a/board/amcc/makalu/Makefile b/board/amcc/makalu/Makefile new file mode 100644 index 00000000000..b8da25ff426 --- /dev/null +++ b/board/amcc/makalu/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o cmd_pll.o memory.o +SOBJS = init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend *~ + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/amcc/makalu/cmd_pll.c b/board/amcc/makalu/cmd_pll.c new file mode 100644 index 00000000000..b2666dd83b0 --- /dev/null +++ b/board/amcc/makalu/cmd_pll.c @@ -0,0 +1,297 @@ +/* + * (C) Copyright 2000, 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * ehnus: change pll frequency. + * Wed Sep 5 11:45:17 CST 2007 + * hsun@udtech.com.cn + */ + + +#include +#include +#include +#include + +#ifdef CONFIG_CMD_EEPROM + +#define EEPROM_CONF_OFFSET 0 +#define EEPROM_TEST_OFFSET 16 +#define EEPROM_SDSTP_PARAM 16 + +#define PLL_NAME_MAX 12 +#define BUF_STEP 8 + +/* eeprom_wirtes 8Byte per op. */ +#define EEPROM_ALTER_FREQ(freq) \ + do { \ + int __i; \ + for (__i = 0; __i < 2; __i++) \ + eeprom_write (CFG_I2C_EEPROM_ADDR, \ + EEPROM_CONF_OFFSET + __i*BUF_STEP, \ + pll_select[freq], \ + BUF_STEP + __i*BUF_STEP); \ + } while (0) + +#define PDEBUG +#ifdef PDEBUG +#define PLL_DEBUG pll_debug(EEPROM_CONF_OFFSET) +#else +#define PLL_DEBUG +#endif + +typedef enum { + PLL_ebc20, + PLL_333, + PLL_4001, + PLL_4002, + PLL_533, + PLL_600, + PLL_666, /* For now, kilauea can't support */ + RCONF, + WTEST, + PLL_TOTAL +} pll_freq_t; + +static const char +pll_name[][PLL_NAME_MAX] = { + "PLL_ebc20", + "PLL_333", + "PLL_400@1", + "PLL_400@2", + "PLL_533", + "PLL_600", + "PLL_666", + "RCONF", + "WTEST", + "" +}; + +/* + * ehnus: + */ +static uchar +pll_select[][EEPROM_SDSTP_PARAM] = { + /* 0: CPU 333MHz EBC 20MHz, for test only */ + { + 0x8c, 0x12, 0xec, 0x12, 0x88, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 0: 333 */ + { + 0x8c, 0x12, 0xec, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 1: 400_266 */ + { + 0x8e, 0x0e, 0xe8, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 2: 400 */ + { + 0x8e, 0x0e, 0xe8, 0x12, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 3: 533 */ + { + 0x8e, 0x43, 0x60, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 4: 600 */ + { + 0x8d, 0x02, 0x34, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + /* 5: 666 */ + { + 0x8d, 0x03, 0x78, 0x13, 0x98, 0x00, 0x0a, 0x00, + 0x40, 0x08, 0x23, 0x50, 0x00, 0x05, 0x00, 0x00 + }, + + {} +}; + +static uchar +testbuf[EEPROM_SDSTP_PARAM] = { + 0x00, 0x11, 0x22, 0x33, 0x44, 0x55, 0x66, 0x77, + 0x88, 0x99, 0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff +}; + +static void +pll_debug(int off) +{ + int i; + uchar buffer[EEPROM_SDSTP_PARAM]; + + memset(buffer, 0, sizeof(buffer)); + eeprom_read(CFG_I2C_EEPROM_ADDR, off, + buffer, EEPROM_SDSTP_PARAM); + + printf("Debug: SDSTP[0-3] at offset \"0x%02x\" lists as follows: \n", off); + for (i = 0; i < EEPROM_SDSTP_PARAM; i++) + printf("%02x ", buffer[i]); + printf("\n"); +} + +static void +test_write(void) +{ + printf("Debug: test eeprom_write ... "); + + /* + * Write twice, 8 bytes per write + */ + eeprom_write (CFG_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET, + testbuf, 8); + eeprom_write (CFG_I2C_EEPROM_ADDR, EEPROM_TEST_OFFSET+8, + testbuf, 16); + printf("done\n"); + + pll_debug(EEPROM_TEST_OFFSET); +} + +int +do_pll_alter (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + char c = '\0'; + pll_freq_t pll_freq; + if (argc < 2) { + printf("Usage: \n%s\n", cmdtp->usage); + goto ret; + } + + for (pll_freq = PLL_ebc20; pll_freq < PLL_TOTAL; pll_freq++) + if (!strcmp(pll_name[pll_freq], argv[1])) + break; + + switch (pll_freq) { + case PLL_ebc20: + case PLL_333: + case PLL_4001: + case PLL_4002: + case PLL_533: + case PLL_600: + EEPROM_ALTER_FREQ(pll_freq); + break; + + case PLL_666: /* not support */ + printf("Choose this option will result in a boot failure." + "\nContinue? (Y/N): "); + + c = getc(); putc('\n'); + + if ((c == 'y') || (c == 'Y')) { + EEPROM_ALTER_FREQ(pll_freq); + break; + } + goto ret; + + case RCONF: + pll_debug(EEPROM_CONF_OFFSET); + goto ret; + case WTEST: + printf("DEBUG: write test\n"); + test_write(); + goto ret; + + default: + printf("Invalid options" + "\n\nUsage: \n%s\n", cmdtp->usage); + goto ret; + } + + printf("PLL set to %s, " + "reset the board to take effect\n", pll_name[pll_freq]); + + PLL_DEBUG; +ret: + return 0; +} + +U_BOOT_CMD( + pllalter, CFG_MAXARGS, 1, do_pll_alter, + "pllalter- change pll frequence \n", + "pllalter - change pll frequence \n\n\ + ** New freq take effect after reset. ** \n\ + ----------------------------------------------\n\ + PLL_ebc20: Board: AMCC 405EX(r) Evaluation Board\n\ + \t Same as PLL_333 \n\ + \t except \n\ + \t EBC: 20 MHz \n\ + ----------------------------------------------\n\ + PLL_333: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 666 MHz \n\ + \t CPU: 333 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 83 MHz \n\ + ------------------------------------------------\n\ + PLL_400@1: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 133 MHz \n\ + \t OPB: 66 MHz \n\ + \t DDR: 133 MHz \n\ + ------------------------------------------------\n\ + PLL_400@2: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 800 MHz \n\ + \t CPU: 400 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_533: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1066 MHz \n\ + \t CPU: 533 MHz \n\ + \t PLB: 177 MHz \n\ + \t OPB: 88 MHz \n\ + \t DDR: 177 MHz \n\ + ----------------------------------------------\n\ + PLL_600: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1200 MHz \n\ + \t CPU: 600 MHz \n\ + \t PLB: 200 MHz \n\ + \t OPB: 100 MHz \n\ + \t DDR: 200 MHz \n\ + ----------------------------------------------\n\ + PLL_666: Board: AMCC 405EX(r) Evaluation Board\n\ + \t VCO: 1333 MHz \n\ + \t CPU: 666 MHz \n\ + \t PLB: 166 MHz \n\ + \t OPB: 83 MHz \n\ + \t DDR: 166 MHz \n\ + -----------------------------------------------\n\ + RCONF: Read current eeprom configuration. \n\ + -----------------------------------------------\n\ + WTEST: Test EEPROM write with predefined values\n\ + -----------------------------------------------\n" + ); + +#endif /* (CONFIG_COMMANDS & CFG_CMD_EEPROM) */ diff --git a/board/amcc/makalu/config.mk b/board/amcc/makalu/config.mk new file mode 100644 index 00000000000..a46b1972492 --- /dev/null +++ b/board/amcc/makalu/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xFFFA0000 diff --git a/board/amcc/makalu/init.S b/board/amcc/makalu/init.S new file mode 100644 index 00000000000..806f5fdee2e --- /dev/null +++ b/board/amcc/makalu/init.S @@ -0,0 +1,154 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Based on code provided from Senao and AMCC + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +#include +#include + +#define mtsdram_as(reg, value) \ + addi r4,0,reg ; \ + mtdcr memcfga,r4 ; \ + addis r4,0,value@h ; \ + ori r4,r4,value@l ; \ + mtdcr memcfgd,r4 ; + + .globl ext_bus_cntlr_init +ext_bus_cntlr_init: + + /* + * DDR2 setup + */ + + /* Following the DDR Core Manual, here is the initialization */ + + /* Step 1 */ + + /* Step 2 */ + + /* Step 3 */ + + /* base=00000000, size=128MByte (5), mode=2 (n*10*4) */ + mtsdram_as(SDRAM_MB0CF, 0x00005201); + + /* SET SDRAM_MB1CF - Not enabled */ + mtsdram_as(SDRAM_MB1CF, 0x00000000); + + /* SET SDRAM_MB2CF - Not enabled */ + mtsdram_as(SDRAM_MB2CF, 0x00000000); + + /* SET SDRAM_MB3CF - Not enabled */ + mtsdram_as(SDRAM_MB3CF, 0x00000000); + + /* SDRAM_CLKTR: Adv Addr clock by 90 deg */ + mtsdram_as(SDRAM_CLKTR,0x80000000); + + /* Refresh Time register (0x30) Refresh every 7.8125uS */ + mtsdram_as(SDRAM_RTR, 0x06180000); + + /* SDRAM_SDTR1 */ + mtsdram_as(SDRAM_SDTR1, 0x80201000); + + /* SDRAM_SDTR2 */ + mtsdram_as(SDRAM_SDTR2, 0x32204232); + + /* SDRAM_SDTR3 */ + mtsdram_as(SDRAM_SDTR3, 0x080b0d1a); + + mtsdram_as(SDRAM_MMODE, 0x00000442); + mtsdram_as(SDRAM_MEMODE, 0x00000404); + + /* SDRAM0_MCOPT1 (0X20) No ECC Gen */ + mtsdram_as(SDRAM_MCOPT1, 0x04322000); + + /* NOP */ + mtsdram_as(SDRAM_INITPLR0, 0xa8380000); + /* precharge 3 DDR clock cycle */ + mtsdram_as(SDRAM_INITPLR1, 0x81900400); + /* EMR2 twr = 2tck */ + mtsdram_as(SDRAM_INITPLR2, 0x81020000); + /* EMR3 twr = 2tck */ + mtsdram_as(SDRAM_INITPLR3, 0x81030000); + /* EMR DLL ENABLE twr = 2tck */ + mtsdram_as(SDRAM_INITPLR4, 0x81010404); + /* MR w/ DLL reset + * Note: 5 is CL. May need to be changed + */ + mtsdram_as(SDRAM_INITPLR5, 0x81000542); + /* precharge 3 DDR clock cycle */ + mtsdram_as(SDRAM_INITPLR6, 0x81900400); + /* Auto-refresh trfc = 26tck */ + mtsdram_as(SDRAM_INITPLR7, 0x8D080000); + /* Auto-refresh trfc = 26tck */ + mtsdram_as(SDRAM_INITPLR8, 0x8D080000); + /* Auto-refresh */ + mtsdram_as(SDRAM_INITPLR9, 0x8D080000); + /* Auto-refresh */ + mtsdram_as(SDRAM_INITPLR10, 0x8D080000); + /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */ + mtsdram_as(SDRAM_INITPLR11, 0x81000442); + mtsdram_as(SDRAM_INITPLR12, 0x81010780); + mtsdram_as(SDRAM_INITPLR13, 0x81010400); + mtsdram_as(SDRAM_INITPLR14, 0x00000000); + mtsdram_as(SDRAM_INITPLR15, 0x00000000); + + /* SET MCIF0_CODT Die Termination On */ + mtsdram_as(SDRAM_CODT, 0x0080f837); + mtsdram_as(SDRAM_MODT0, 0x01800000); +#if 0 /* test-only: not sure if 0 is ok when 2nd bank is used */ + mtsdram_as(SDRAM_MODT1, 0x00000000); +#endif + + mtsdram_as(SDRAM_WRDTR, 0x00000000); + + /* SDRAM0_MCOPT2 (0X21) Start initialization */ + mtsdram_as(SDRAM_MCOPT2, 0x20000000); + + /* Step 5 */ + lis r3,0x1 /* 400000 = wait 100ms */ + mtctr r3 + +pll_wait: + bdnz pll_wait + + /* Step 6 */ + + /* SDRAM_DLCR */ + mtsdram_as(SDRAM_DLCR, 0x030000a5); + + /* SDRAM_RDCC */ + mtsdram_as(SDRAM_RDCC, 0x40000000); + + /* SDRAM_RQDC */ + mtsdram_as(SDRAM_RQDC, 0x80000038); + + /* SDRAM_RFDC */ + mtsdram_as(SDRAM_RFDC, 0x00000209); + + /* Enable memory controller */ + mtsdram_as(SDRAM_MCOPT2, 0x28000000); + + blr diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c new file mode 100644 index 00000000000..3b4a9c15477 --- /dev/null +++ b/board/amcc/makalu/makalu.c @@ -0,0 +1,378 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_PCI) +#include +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ + +/* + * Board early initialization function + */ +int board_early_init_f (void) +{ + /*--------------------------------------------------------------------+ + | Interrupt controller setup for the AMCC 405EX(r) PINE evaluation board. + +--------------------------------------------------------------------+ + +---------------------------------------------------------------------+ + |Interrupt| Source | Pol. | Sensi.| Crit. | + +---------+-----------------------------------+-------+-------+-------+ + | IRQ 00 | UART0 | High | Level | Non | + | IRQ 01 | UART1 | High | Level | Non | + | IRQ 02 | IIC0 | High | Level | Non | + | IRQ 03 | TBD | High | Level | Non | + | IRQ 04 | TBD | High | Level | Non | + | IRQ 05 | EBM | High | Level | Non | + | IRQ 06 | BGI | High | Level | Non | + | IRQ 07 | IIC1 | Rising| Edge | Non | + | IRQ 08 | SPI | High | Lvl/ed| Non | + | IRQ 09 | External IRQ 0 - (PCI-Express) | pgm H | Pgm | Non | + | IRQ 10 | MAL TX EOB | High | Level | Non | + | IRQ 11 | MAL RX EOB | High | Level | Non | + | IRQ 12 | DMA Channel 0 FIFO Full | High | Level | Non | + | IRQ 13 | DMA Channel 0 Stat FIFO | High | Level | Non | + | IRQ 14 | DMA Channel 1 FIFO Full | High | Level | Non | + | IRQ 15 | DMA Channel 1 Stat FIFO | High | Level | Non | + | IRQ 16 | PCIE0 AL | high | Level | Non | + | IRQ 17 | PCIE0 VPD access | rising| Edge | Non | + | IRQ 18 | PCIE0 hot reset request | rising| Edge | Non | + | IRQ 19 | PCIE0 hot reset request | faling| Edge | Non | + | IRQ 20 | PCIE0 TCR | High | Level | Non | + | IRQ 21 | PCIE0 MSI level0 | High | Level | Non | + | IRQ 22 | PCIE0 MSI level1 | High | Level | Non | + | IRQ 23 | Security EIP-94 | High | Level | Non | + | IRQ 24 | EMAC0 interrupt | High | Level | Non | + | IRQ 25 | EMAC1 interrupt | High | Level | Non | + | IRQ 26 | PCIE0 MSI level2 | High | Level | Non | + | IRQ 27 | External IRQ 4 | pgm H | Pgm | Non | + | IRQ 28 | UIC2 Non-critical Int. | High | Level | Non | + | IRQ 29 | UIC2 Critical Interrupt | High | Level | Crit. | + | IRQ 30 | UIC1 Non-critical Int. | High | Level | Non | + | IRQ 31 | UIC1 Critical Interrupt | High | Level | Crit. | + |---------------------------------------------------------------------- + | IRQ 32 | MAL Serr | High | Level | Non | + | IRQ 33 | MAL Txde | High | Level | Non | + | IRQ 34 | MAL Rxde | High | Level | Non | + | IRQ 35 | PCIE0 bus master VC0 |falling| Edge | Non | + | IRQ 36 | PCIE0 DCR Error | High | Level | Non | + | IRQ 37 | EBC | High |Lvl Edg| Non | + | IRQ 38 | NDFC | High | Level | Non | + | IRQ 39 | GPT Compare Timer 8 | Risin | Edge | Non | + | IRQ 40 | GPT Compare Timer 9 | Risin | Edge | Non | + | IRQ 41 | PCIE1 AL | high | Level | Non | + | IRQ 42 | PCIE1 VPD access | rising| edge | Non | + | IRQ 43 | PCIE1 hot reset request | rising| Edge | Non | + | IRQ 44 | PCIE1 hot reset request | faling| Edge | Non | + | IRQ 45 | PCIE1 TCR | High | Level | Non | + | IRQ 46 | PCIE1 bus master VC0 |falling| Edge | Non | + | IRQ 47 | GPT Compare Timer 3 | Risin | Edge | Non | + | IRQ 48 | GPT Compare Timer 4 | Risin | Edge | Non | + | IRQ 49 | Ext. IRQ 7 |pgm/Fal|pgm/Lvl| Non | + | IRQ 50 | Ext. IRQ 8 - |pgm (H)|pgm/Lvl| Non | + | IRQ 51 | Ext. IRQ 9 |pgm (H)|pgm/Lvl| Non | + | IRQ 52 | GPT Compare Timer 5 | high | Edge | Non | + | IRQ 53 | GPT Compare Timer 6 | high | Edge | Non | + | IRQ 54 | GPT Compare Timer 7 | high | Edge | Non | + | IRQ 55 | Serial ROM | High | Level | Non | + | IRQ 56 | GPT Decrement Pulse | High | Level | Non | + | IRQ 57 | Ext. IRQ 2 |pgm/Fal|pgm/Lvl| Non | + | IRQ 58 | Ext. IRQ 5 |pgm/Fal|pgm/Lvl| Non | + | IRQ 59 | Ext. IRQ 6 |pgm/Fal|pgm/Lvl| Non | + | IRQ 60 | EMAC0 Wake-up | High | Level | Non | + | IRQ 61 | Ext. IRQ 1 |pgm/Fal|pgm/Lvl| Non | + | IRQ 62 | EMAC1 Wake-up | High | Level | Non | + |---------------------------------------------------------------------- + | IRQ 64 | PE0 AL | High | Level | Non | + | IRQ 65 | PE0 VPD Access | Risin | Edge | Non | + | IRQ 66 | PE0 Hot Reset Request | Risin | Edge | Non | + | IRQ 67 | PE0 Hot Reset Request | Falli | Edge | Non | + | IRQ 68 | PE0 TCR | High | Level | Non | + | IRQ 69 | PE0 BusMaster VCO | Falli | Edge | Non | + | IRQ 70 | PE0 DCR Error | High | Level | Non | + | IRQ 71 | Reserved | N/A | N/A | Non | + | IRQ 72 | PE1 AL | High | Level | Non | + | IRQ 73 | PE1 VPD Access | Risin | Edge | Non | + | IRQ 74 | PE1 Hot Reset Request | Risin | Edge | Non | + | IRQ 75 | PE1 Hot Reset Request | Falli | Edge | Non | + | IRQ 76 | PE1 TCR | High | Level | Non | + | IRQ 77 | PE1 BusMaster VCO | Falli | Edge | Non | + | IRQ 78 | PE1 DCR Error | High | Level | Non | + | IRQ 79 | Reserved | N/A | N/A | Non | + | IRQ 80 | PE2 AL | High | Level | Non | + | IRQ 81 | PE2 VPD Access | Risin | Edge | Non | + | IRQ 82 | PE2 Hot Reset Request | Risin | Edge | Non | + | IRQ 83 | PE2 Hot Reset Request | Falli | Edge | Non | + | IRQ 84 | PE2 TCR | High | Level | Non | + | IRQ 85 | PE2 BusMaster VCO | Falli | Edge | Non | + | IRQ 86 | PE2 DCR Error | High | Level | Non | + | IRQ 87 | Reserved | N/A | N/A | Non | + | IRQ 88 | External IRQ(5) | Progr | Progr | Non | + | IRQ 89 | External IRQ 4 - Ethernet | Progr | Progr | Non | + | IRQ 90 | External IRQ 3 - PCI-X | Progr | Progr | Non | + | IRQ 91 | External IRQ 2 - PCI-X | Progr | Progr | Non | + | IRQ 92 | External IRQ 1 - PCI-X | Progr | Progr | Non | + | IRQ 93 | External IRQ 0 - PCI-X | Progr | Progr | Non | + | IRQ 94 | Reserved | N/A | N/A | Non | + | IRQ 95 | Reserved | N/A | N/A | Non | + |--------------------------------------------------------------------- + +---------+-----------------------------------+-------+-------+------*/ + /*--------------------------------------------------------------------+ + | Initialise UIC registers. Clear all interrupts. Disable all + | interrupts. + | Set critical interrupt values. Set interrupt polarities. Set + | interrupt trigger levels. Make bit 0 High priority. Clear all + | interrupts again. + +-------------------------------------------------------------------*/ + + mtdcr (uic2sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic2er, 0x00000000); /* disable all interrupts */ + mtdcr (uic2cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic2pr, 0xf7ffffff); /* Set Interrupt Polarities */ + mtdcr (uic2tr, 0x01e1fff8); /* Set Interrupt Trigger Levels */ + mtdcr (uic2vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic2sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic2sr, 0xffffffff); /* clear all interrupts */ + + mtdcr (uic1sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic1er, 0x00000000); /* disable all interrupts */ + mtdcr (uic1cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic1pr, 0xfffac785); /* Set Interrupt Polarities */ + mtdcr (uic1tr, 0x001d0040); /* Set Interrupt Trigger Levels */ + mtdcr (uic1vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic1sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic1sr, 0xffffffff); /* clear all interrupts */ + + mtdcr (uic0sr, 0xffffffff); /* Clear all interrupts */ + mtdcr (uic0er, 0x0000000a); /* Disable all interrupts */ + /* Except cascade UIC0 and UIC1 */ + mtdcr (uic0cr, 0x00000000); /* Set Critical / Non Critical interrupts */ + mtdcr (uic0pr, 0xffbfefef); /* Set Interrupt Polarities */ + mtdcr (uic0tr, 0x00007000); /* Set Interrupt Trigger Levels */ + mtdcr (uic0vr, 0x00000001); /* Set Vect base=0,INT31 Highest priority */ + mtdcr (uic0sr, 0x00000000); /* clear all interrupts */ + mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */ + + /* + * Note: Some cores are still in reset when the chip starts, so + * take them out of reset + */ + mtsdr(SDR0_SRST, 0); + + return 0; +} + +int misc_init_r(void) +{ +#ifdef CFG_ENV_IS_IN_FLASH + /* Monitor protection ON by default */ + flash_protect(FLAG_PROTECT_SET, + -CFG_MONITOR_LEN, + 0xffffffff, + &flash_info[0]); +#endif + + return 0; +} + +int checkboard (void) +{ + char *s = getenv("serial#"); + + printf("Board: Makalu - AMCC PPC405EX Evaluation Board"); + + if (s != NULL) { + puts(", serial# "); + puts(s); + } + putc('\n'); + + return (0); +} + +/************************************************************************* + * pci_pre_init + * + * This routine is called just prior to registering the hose and gives + * the board the opportunity to check things. Returning a value of zero + * indicates that things are bad & PCI initialization should be aborted. + * + * Different boards may wish to customize the pci controller structure + * (add regions, override default access routines, etc) or perform + * certain pre-initialization actions. + * + ************************************************************************/ +#if defined(CONFIG_PCI) +int pci_pre_init(struct pci_controller * hose ) +{ + return 0; +} +#endif /* defined(CONFIG_PCI) */ + +/************************************************************************* + * pci_target_init + * + * The bootstrap configuration provides default settings for the pci + * inbound map (PIM). But the bootstrap config choices are limited and + * may not be sufficient for a given board. + * + ************************************************************************/ +#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) +void pci_target_init(struct pci_controller * hose ) +{ + /*-------------------------------------------------------------------+ + * Disable everything + *-------------------------------------------------------------------*/ + out32r( PCIX0_PIM0SA, 0 ); /* disable */ + out32r( PCIX0_PIM1SA, 0 ); /* disable */ + out32r( PCIX0_PIM2SA, 0 ); /* disable */ + out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */ + + /*-------------------------------------------------------------------+ + * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 + * strapping options to not support sizes such as 128/256 MB. + *-------------------------------------------------------------------*/ + out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE ); + out32r( PCIX0_PIM0LAH, 0 ); + out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 ); + + out32r( PCIX0_BAR0, 0 ); + + /*-------------------------------------------------------------------+ + * Program the board's subsystem id/vendor id + *-------------------------------------------------------------------*/ + out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID ); + out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID ); + + out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY ); +} +#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ + +#ifdef CONFIG_PCI +static struct pci_controller pcie_hose[2] = {{0},{0}}; + +void pcie_setup_hoses(int busno) +{ + struct pci_controller *hose; + int i, bus; + int ret = 0; + bus = busno; + char *env; + unsigned int delay; + + for (i = 0; i < 2; i++) { + + if (is_end_point(i)) { + printf("PCIE%d: will be configured as endpoint\n", i); + ret = ppc4xx_init_pcie_endport(i); + } else { + printf("PCIE%d: will be configured as root-complex\n", i); + ret = ppc4xx_init_pcie_rootport(i); + } + if (ret) { + printf("PCIE%d: initialization failed\n", i); + continue; + } + + hose = &pcie_hose[i]; + hose->first_busno = bus; + hose->last_busno = bus; + hose->current_busno = bus; + + /* setup mem resource */ + pci_set_region(hose->regions + 0, + CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, + CFG_PCIE_MEMBASE + i * CFG_PCIE_MEMSIZE, + CFG_PCIE_MEMSIZE, + PCI_REGION_MEM); + hose->region_count = 1; + pci_register_hose(hose); + + if (is_end_point(i)) { + ppc4xx_setup_pcie_endpoint(hose, i); + /* + * Reson for no scanning is endpoint can not generate + * upstream configuration accesses. + */ + } else { + ppc4xx_setup_pcie_rootpoint(hose, i); + env = getenv ("pciscandelay"); + if (env != NULL) { + delay = simple_strtoul(env, NULL, 10); + if (delay > 5) + printf("Warning, expect noticable delay before " + "PCIe scan due to 'pciscandelay' value!\n"); + mdelay(delay * 1000); + } + + /* + * Config access can only go down stream + */ + hose->last_busno = pci_hose_scan(hose); + bus = hose->last_busno + 1; + } + } +} +#endif + +#if defined(CONFIG_POST) +/* + * Returns 1 if keys pressed to start the power-on long-running tests + * Called from board_init_f(). + */ +int post_hotkeys_pressed(void) +{ + return 0; /* No hotkeys supported */ +} +#endif /* CONFIG_POST */ + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + u32 val[4]; + int rc; + + ft_cpu_setup(blob, bd); + + /* Fixup NOR mapping */ + val[0] = 0; /* chip select number */ + val[1] = 0; /* always 0 */ + val[2] = gd->bd->bi_flashstart; + val[3] = gd->bd->bi_flashsize; + rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", + val, sizeof(val), 1); + if (rc) + printf("Unable to update property NOR mapping, err=%s\n", + fdt_strerror(rc)); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/board/amcc/makalu/memory.c b/board/amcc/makalu/memory.c new file mode 100644 index 00000000000..b03b60b8f4a --- /dev/null +++ b/board/amcc/makalu/memory.c @@ -0,0 +1,188 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +void sdram_init(void) +{ + return; +} + +long int initdram(int board_type) +{ + /* + * Same as on Kilauea, Makalu generates exception 0x200 + * (machine check) after trap_init() in board_init_f, + * when SDRAM is initialized here (late) and d-cache is + * used earlier as INIT_RAM. + * So for now, initialize DDR2 in init.S very early and + * also use it for INIT_RAM. Then this exception doesn't + * occur. + */ +#if 0 + u32 val; + + /* base=00000000, size=128MByte (5), mode=2 (n*10*4) */ + mtsdram(SDRAM_MB0CF, 0x00005201); + + /* SET SDRAM_MB1CF - Not enabled */ + mtsdram(SDRAM_MB1CF, 0x00000000); + + /* SET SDRAM_MB2CF - Not enabled */ + mtsdram(SDRAM_MB2CF, 0x00000000); + + /* SET SDRAM_MB3CF - Not enabled */ + mtsdram(SDRAM_MB3CF, 0x00000000); + + /* SDRAM_CLKTR: Adv Addr clock by 90 deg */ + mtsdram(SDRAM_CLKTR, 0x80000000); + + /* Refresh Time register (0x30) Refresh every 7.8125uS */ + mtsdram(SDRAM_RTR, 0x06180000); + + /* SDRAM_SDTR1 */ + mtsdram(SDRAM_SDTR1, 0x80201000); + + /* SDRAM_SDTR2 */ + mtsdram(SDRAM_SDTR2, 0x32204232); + + /* SDRAM_SDTR3 */ + mtsdram(SDRAM_SDTR3, 0x080b0d1a); + + mtsdram(SDRAM_MMODE, 0x00000442); + mtsdram(SDRAM_MEMODE, 0x00000404); + + /* SDRAM0_MCOPT1 (0X20) No ECC Gen */ + mtsdram(SDRAM_MCOPT1, 0x04322000); + + /* NOP */ + mtsdram(SDRAM_INITPLR0, 0xa8380000); + /* precharge 3 DDR clock cycle */ + mtsdram(SDRAM_INITPLR1, 0x81900400); + /* EMR2 twr = 2tck */ + mtsdram(SDRAM_INITPLR2, 0x81020000); + /* EMR3 twr = 2tck */ + mtsdram(SDRAM_INITPLR3, 0x81030000); + /* EMR DLL ENABLE twr = 2tck */ + mtsdram(SDRAM_INITPLR4, 0x81010404); + /* MR w/ DLL reset + * Note: 5 is CL. May need to be changed + */ + mtsdram(SDRAM_INITPLR5, 0x81000542); + /* precharge 3 DDR clock cycle */ + mtsdram(SDRAM_INITPLR6, 0x81900400); + /* Auto-refresh trfc = 26tck */ + mtsdram(SDRAM_INITPLR7, 0x8D080000); + /* Auto-refresh trfc = 26tck */ + mtsdram(SDRAM_INITPLR8, 0x8D080000); + /* Auto-refresh */ + mtsdram(SDRAM_INITPLR9, 0x8D080000); + /* Auto-refresh */ + mtsdram(SDRAM_INITPLR10, 0x8D080000); + /* MRS - normal operation; wait 2 cycle (set wait to tMRD) */ + mtsdram(SDRAM_INITPLR11, 0x81000442); + mtsdram(SDRAM_INITPLR12, 0x81010780); + mtsdram(SDRAM_INITPLR13, 0x81010400); + mtsdram(SDRAM_INITPLR14, 0x00000000); + mtsdram(SDRAM_INITPLR15, 0x00000000); + + /* SET MCIF0_CODT Die Termination On */ + mtsdram(SDRAM_CODT, 0x0080f837); + mtsdram(SDRAM_MODT0, 0x01800000); + mtsdram(SDRAM_MODT1, 0x00000000); + + mtsdram(SDRAM_WRDTR, 0x00000000); + + /* SDRAM0_MCOPT2 (0X21) Start initialization */ + mtsdram(SDRAM_MCOPT2, 0x20000000); + + /* Step 5 */ + do { + mfsdram(SDRAM_MCSTAT, val); + } while ((val & SDRAM_MCSTAT_MIC_COMP) != SDRAM_MCSTAT_MIC_COMP); + + /* Step 6 */ + + /* SDRAM_DLCR */ + mtsdram(SDRAM_DLCR, 0x030000a5); + + /* SDRAM_RDCC */ + mtsdram(SDRAM_RDCC, 0x40000000); + + /* SDRAM_RQDC */ + mtsdram(SDRAM_RQDC, 0x80000038); + + /* SDRAM_RFDC */ + mtsdram(SDRAM_RFDC, 0x00000209); + + /* Enable memory controller */ + mfsdram(SDRAM_MCOPT2, val); + val |= SDRAM_MCOPT2_DCEN_ENABLE; + mtsdram(SDRAM_MCOPT2, val); +#endif + return (CFG_MBYTES_SDRAM << 20); +} + +#if defined(CFG_DRAM_TEST) +int testdram (void) +{ + printf ("testdram\n"); +#if defined (CONFIG_NAND_U_BOOT) + return 0; +#endif + uint *pstart = (uint *) 0x00000000; + uint *pend = (uint *) 0x00001000; + uint *p; + + for (p = pstart; p < pend; p++) { + *p = 0xaaaaaaaa; + } + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test fails at: %08x\n", (uint) p); +#endif + return 1; + } + } + + for (p = pstart; p < pend; p++) { + *p = 0x55555555; + } + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test fails at: %08x\n", (uint) p); +#endif + return 1; + } + } +#if !defined (CONFIG_NAND_SPL) + printf ("SDRAM test passed!!!\n"); +#endif + return 0; +} +#endif diff --git a/board/amcc/makalu/u-boot.lds b/board/amcc/makalu/u-boot.lds new file mode 100644 index 00000000000..390b3f397b2 --- /dev/null +++ b/board/amcc/makalu/u-boot.lds @@ -0,0 +1,137 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ +/* To compile successfully, uncomment the following section. + * To go in ram, remove the section. + * Added by SunHe. + */ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/ppc4xx/start.o (.text) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/makalu.h b/include/configs/makalu.h new file mode 100644 index 00000000000..6c4d0b6e21b --- /dev/null +++ b/include/configs/makalu.h @@ -0,0 +1,387 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * makalu.h - configuration for AMCC Makalu (405EX) + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_MAKALU 1 /* Board is Makalu */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_405EX 1 /* Specifc 405EX support*/ +#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFE000000 +#define CFG_FPGA_BASE 0xF0000000 +#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE (TEXT_BASE) + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */ +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +/* reserve some memory for POST and BOOT limit info */ +#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) + +/* extra data in init-ram */ +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) +#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8) +#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12) +#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */ + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM 128 + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ +#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ + +/* Standard DTT sensor configuration */ +#define CONFIG_DTT_DS1775 1 +#define CONFIG_DTT_SENSORS { 0 } +#define CFG_I2C_DTT_ADDR 0x48 + +/* RTC configuration */ +#define CONFIG_RTC_X1205 1 +#define CFG_I2C_RTC_ADDR 0x6f + +/*----------------------------------------------------------------------- + * Ethernet + *----------------------------------------------------------------------*/ +#define CONFIG_M88E1111_PHY 1 +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 1 + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 2 + +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "logversion=2\0" \ + "netdev=eth0\0" \ + "hostname=makalu\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm 200000\0" \ + "net_nfs_fdt=tftp 200000 ${bootfile};" \ + "tftp ${fdt_addr} ${fdt_file};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm 200000 - ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=makalu/uImage\0" \ + "fdt_file=makalu/makalu.dtb\0" \ + "fdt_addr=400000\0" \ + "kernel_addr=fe000000\0" \ + "ramdisk_addr=fe200000\0" \ + "initrd_high=30000000\0" \ + "load=tftp 200000 makalu/u-boot.bin\0" \ + "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ + "cp.b ${fileaddr} fffa0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + "pciconfighost=1\0" \ + "pcie_mode=RP:RP\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_LOG +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CACHE | \ + CFG_POST_CPU | \ + CFG_POST_ETHER | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_UART) + +/* Define here the base-addresses of the UARTs to test in POST */ +#define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE} + +#define CONFIG_LOGBUFFER +#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ + +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CONFIG_PCI_CONFIG_HOST_BRIDGE + +/*----------------------------------------------------------------------- + * PCIe stuff + *----------------------------------------------------------------------*/ +#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ +#define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ + +#define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */ +#define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */ +#define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ + +#define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */ +#define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */ +#define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ + +#define CFG_PCIE0_UTLBASE 0xef502000 +#define CFG_PCIE1_UTLBASE 0xef503000 + +/* base address of inbound PCIe window */ +#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Cache Configuration + *----------------------------------------------------------------------*/ +#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */ +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x04011000 +#define CFG_EBC_PB0CR 0xFE0BA000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x9400C800 +#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */ + +#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ + +/*----------------------------------------------------------------------- + * GPIO Setup + *----------------------------------------------------------------------*/ +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EX specific) + * + * GPIO0[0-3] - EBC data 0-3 inputs/outputs + * GPIO0[4-7] - USB data 4-7 inputs/outputs + * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs + * GPIO0[12-15] - USB data 0-3 inputs/outputs + * GPIO0[16-21] - UART0 control signal inputs/outputs + * + * GPIO0[22-25,27] - EBC control signal inputs/outputs + * GPIO0[26] - Instruction trace outputs + * GPIO0[28] - Float, N/C + * GPIO0[29-31] - DMA control signal inputs/outputs + */ +#define CFG_GPIO0_OSRL 0x00AA54AA +#define CFG_GPIO0_OSRH 0x55500000 +#define CFG_GPIO0_TSRL 0x00AA54AA +#define CFG_GPIO0_TSRH 0x55500000 +#define CFG_GPIO0_ISR1L 0x00005400 +#define CFG_GPIO0_ISR1H 0x55500000 +#define CFG_GPIO0_ISR2L 0x00550055 +#define CFG_GPIO0_ISR2H 0x00000000 + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,405EX@0" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From afe9fa59cb63b4f9d16bf01c93eb212f25a38c2a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 22 Oct 2007 16:24:44 +0200 Subject: ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boards Signed-off-by: Stefan Roese --- include/configs/katmai.h | 2 +- include/configs/kilauea.h | 1 + include/configs/makalu.h | 1 + 3 files changed, 3 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 6bc8d025ae0..5da00fc8e55 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -247,7 +247,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM - +#define CONFIG_CMD_SNTP #define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ #define CONFIG_MII 1 /* MII PHY management */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 74c94830c22..90bdd6959b7 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -244,6 +244,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP /* POST support */ #define CONFIG_POST (CFG_POST_MEMORY | \ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 6c4d0b6e21b..3e3b008c6eb 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -234,6 +234,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP /* POST support */ #define CONFIG_POST (CFG_POST_MEMORY | \ -- cgit v1.3.1 From 353f2688b4e0fc7b969bc70a02be4b40bf0dd124 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 23 Oct 2007 10:10:08 +0200 Subject: ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: Stefan Roese --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 6 ++++-- board/amcc/kilauea/kilauea.c | 36 +++++++++++++++++++++++++++++++++--- cpu/ppc4xx/4xx_enet.c | 10 ++++++++++ include/configs/kilauea.h | 1 + 6 files changed, 50 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 5ae588f6644..bf0ebb17583 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -303,6 +303,7 @@ Stefan Roese bamboo PPC440EP bunbinga PPC405EP ebony PPC440GP + haleakala PPC405EXr katmai PPC440SPe kilauea PPC405EX lwmon5 PPC440EPx diff --git a/MAKEALL b/MAKEALL index 874d3a6710d..67b39c319b5 100755 --- a/MAKEALL +++ b/MAKEALL @@ -180,6 +180,7 @@ LIST_4xx=" \ ERIC \ EXBITGEN \ G2000 \ + haleakala \ hcu4 \ hcu5 \ HH405 \ diff --git a/Makefile b/Makefile index 039cec08f76..814bba8af72 100644 --- a/Makefile +++ b/Makefile @@ -1168,8 +1168,10 @@ KAREF_config: unconfig katmai_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx katmai amcc -kilauea_config: unconfig - @$(MKCONFIG) $(@:_config=) ppc ppc4xx kilauea amcc +# Kilauea & Haleakala images are identical (recognized via PVR) +kilauea_config \ +haleakala_config: unconfig + @$(MKCONFIG) -n $@ -a kilauea ppc ppc4xx kilauea amcc luan_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx luan amcc diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c index b59bd6fc0e2..77c0eb43641 100644 --- a/board/amcc/kilauea/kilauea.c +++ b/board/amcc/kilauea/kilauea.c @@ -26,7 +26,7 @@ #include #include #include -#include +#include #if defined(CONFIG_PCI) #include @@ -225,11 +225,41 @@ int misc_init_r(void) return 0; } +int board_emac_count(void) +{ + u32 pvr = get_pvr(); + + /* + * 405EXr only has one EMAC interface, 405EX has two + */ + if ((pvr == PVR_405EXR1_RA) || (pvr == PVR_405EXR2_RA)) + return 1; + else + return 2; +} + +static int board_pcie_count(void) +{ + u32 pvr = get_pvr(); + + /* + * 405EXr only has one EMAC interface, 405EX has two + */ + if ((pvr == PVR_405EXR1_RA) || (pvr == PVR_405EXR2_RA)) + return 1; + else + return 2; +} + int checkboard (void) { char *s = getenv("serial#"); + u32 pvr = get_pvr(); - printf("Board: Kilauea - AMCC PPC405EX Evaluation Board"); + if ((pvr == PVR_405EXR1_RA) || (pvr == PVR_405EXR2_RA)) + printf("Board: Haleakala - AMCC PPC405EXr Evaluation Board"); + else + printf("Board: Kilauea - AMCC PPC405EX Evaluation Board"); if (s != NULL) { puts(", serial# "); @@ -310,7 +340,7 @@ void pcie_setup_hoses(int busno) char *env; unsigned int delay; - for (i = 0; i < 2; i++) { + for (i = 0; i < board_pcie_count(); i++) { if (is_end_point(i)) { printf("PCIE%d: will be configured as endpoint\n", i); diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 6b4834481e3..67b3a24d2ff 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -158,7 +158,14 @@ struct eth_device *emac0_dev = NULL; /* * Get count of EMAC devices (doesn't have to be the max. possible number * supported by the cpu) + * + * CONFIG_BOARD_EMAC_COUNT added so now a "dynamic" way to configure the + * EMAC count is possible. As it is needed for the Kilauea/Haleakala + * 405EX/405EXr eval board, using the same binary. */ +#if defined(CONFIG_BOARD_EMAC_COUNT) +#define LAST_EMAC_NUM board_emac_count() +#else /* CONFIG_BOARD_EMAC_COUNT */ #if defined(CONFIG_HAS_ETH3) #define LAST_EMAC_NUM 4 #elif defined(CONFIG_HAS_ETH2) @@ -168,6 +175,7 @@ struct eth_device *emac0_dev = NULL; #else #define LAST_EMAC_NUM 1 #endif +#endif /* CONFIG_BOARD_EMAC_COUNT */ /* normal boards start with EMAC0 */ #if !defined(CONFIG_EMAC_NR_START) @@ -197,6 +205,8 @@ extern int emac4xx_miiphy_read (char *devname, unsigned char addr, extern int emac4xx_miiphy_write (char *devname, unsigned char addr, unsigned char reg, unsigned short value); +int board_emac_count(void); + /*-----------------------------------------------------------------------------+ | ppc_4xx_eth_halt | Disable MAL channel, and EMACn diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 90bdd6959b7..9a9f7ba1bc2 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -38,6 +38,7 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_EMAC_COUNT /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the -- cgit v1.3.1 From f10493c6d77a1e07a6c2ff4d772937a5e7359d6a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 23 Oct 2007 11:31:05 +0200 Subject: ppc4xx: Correct UART input clock calculation and passing to fdt We now use a value in the gd (global data) structure for the UART input frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely in get_sys_info(). Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_uart.c | 4 ++-- cpu/ppc4xx/fdt.c | 8 +++++--- include/asm-ppc/global_data.h | 3 +++ 3 files changed, 10 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_uart.c b/cpu/ppc4xx/4xx_uart.c index c6b229f3a6c..ac2b12b8773 100644 --- a/cpu/ppc4xx/4xx_uart.c +++ b/cpu/ppc4xx/4xx_uart.c @@ -192,9 +192,9 @@ static void serial_init_common(u32 base, u32 udiv, u16 bdiv) * the UART divisor is available */ #ifdef CFG_EXT_SERIAL_CLOCK - sys_info.freqUART = CFG_EXT_SERIAL_CLOCK; + gd->uart_clk = CFG_EXT_SERIAL_CLOCK; #else - sys_info.freqUART = sys_info.freqUART / udiv; + gd->uart_clk = sys_info.freqUART / udiv; #endif out_8((u8 *)base + UART_LCR, 0x80); /* set DLAB bit */ diff --git a/cpu/ppc4xx/fdt.c b/cpu/ppc4xx/fdt.c index bf97c2a4356..dcedbbb3083 100644 --- a/cpu/ppc4xx/fdt.c +++ b/cpu/ppc4xx/fdt.c @@ -36,6 +36,8 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + static void do_fixup(void *fdt, const char *node, const char *prop, const void *val, int len, int create) { @@ -44,7 +46,7 @@ static void do_fixup(void *fdt, const char *node, const char *prop, debug("Updating property '%s/%s' = ", node, prop); for (i = 0; i < len; i++) debug(" %.2x", *(u8*)(val+i)); - debug("\n"); + debug("(%d)\n", *(u32 *)val); #endif int rc = fdt_find_and_setprop(fdt, node, prop, val, len, create); if (rc) @@ -83,9 +85,9 @@ static void do_fixup_uart(void *fdt, int offset, int i, bd_t *bd) get_sys_info(&sys_info); - debug("Updating node UART%d\n", i); + debug("Updating node UART%d: clock-frequency=%d\n", i, gd->uart_clk); - val = cpu_to_fdt32(sys_info.freqUART); + val = cpu_to_fdt32(gd->uart_clk); rc = fdt_setprop(fdt, offset, "clock-frequency", &val, 4); if (rc) printf("Unable to update node UART, err=%s\n", fdt_strerror(rc)); diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 4676e2c4089..05aee749494 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -107,6 +107,9 @@ typedef struct global_data { unsigned int dp_alloc_base; unsigned int dp_alloc_top; #endif +#if defined(CONFIG_4xx) + u32 uart_clk; +#endif /* CONFIG_4xx */ #if defined(CFG_GT_6426x) unsigned int mirror_hack[16]; #endif -- cgit v1.3.1 From 9b94ac61d2176185c30adf0793e079ec30e68687 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 31 Oct 2007 17:55:58 +0100 Subject: ppc4xx: Rework 4xx cache support New cache handling functions added and all existing functions moved from start.S into seperate cache.S. Signed-off-by: Stefan Roese --- cpu/ppc4xx/Makefile | 40 +++++++-- cpu/ppc4xx/cache.S | 233 ++++++++++++++++++++++++++++++++++++++++++++++++ cpu/ppc4xx/kgdb.S | 8 +- cpu/ppc4xx/start.S | 144 +++++------------------------- include/asm-ppc/cache.h | 21 +++-- include/ppc405.h | 6 ++ include/ppc440.h | 6 +- lib_ppc/cache.c | 2 +- 8 files changed, 315 insertions(+), 145 deletions(-) create mode 100644 cpu/ppc4xx/cache.S (limited to 'include') diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index 194724990de..9155e9a98d1 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -25,14 +25,38 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(CPU).a -START = start.o resetvec.o kgdb.o -SOBJS = dcr.o -COBJS = 40x_spd_sdram.o 44x_spd_ddr.o 44x_spd_ddr2.o \ - 4xx_enet.o 4xx_pci.o 4xx_pcie.o 4xx_uart.o \ - bedbug_405.o commproc.o cpu.o cpu_init.o \ - fdt.o gpio.o i2c.o interrupts.o iop480_uart.o \ - miiphy.o ndfc.o sdram.o speed.o \ - tlb.o traps.o usb.o usb_ohci.o usbdev.o +START := resetvec.o +START += start.o + +SOBJS := cache.o +SOBJS += dcr.o +SOBJS += kgdb.o + +COBJS := 40x_spd_sdram.o +COBJS += 44x_spd_ddr.o +COBJS += 44x_spd_ddr2.o +COBJS += 4xx_enet.o +COBJS += 4xx_pci.o +COBJS += 4xx_pcie.o +COBJS += 4xx_uart.o +COBJS += bedbug_405.o +COBJS += commproc.o +COBJS += cpu.o +COBJS += cpu_init.o +COBJS += fdt.o +COBJS += gpio.o +COBJS += i2c.o +COBJS += interrupts.o +COBJS += iop480_uart.o +COBJS += miiphy.o +COBJS += ndfc.o +COBJS += sdram.o +COBJS += speed.o +COBJS += tlb.o +COBJS += traps.o +COBJS += usb.o +COBJS += usb_ohci.o +COBJS += usbdev.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/cpu/ppc4xx/cache.S b/cpu/ppc4xx/cache.S new file mode 100644 index 00000000000..5124dec77f4 --- /dev/null +++ b/cpu/ppc4xx/cache.S @@ -0,0 +1,233 @@ +/* + * This file contains miscellaneous low-level functions. + * Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org) + * + * Largely rewritten by Cort Dougan (cort@cs.nmt.edu) + * and Paul Mackerras. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + */ + +#include +#include +#include +#include +#include +#include +#include + +/* + * Flush instruction cache. + */ +_GLOBAL(invalidate_icache) + iccci r0,r0 + isync + blr + +/* + * Write any modified data cache blocks out to memory + * and invalidate the corresponding instruction cache blocks. + * + * flush_icache_range(unsigned long start, unsigned long stop) + */ +_GLOBAL(flush_icache_range) + li r5,L1_CACHE_BYTES-1 + andc r3,r3,r5 + subf r4,r3,r4 + add r4,r4,r5 + srwi. r4,r4,L1_CACHE_SHIFT + beqlr + mtctr r4 + mr r6,r3 +1: dcbst 0,r3 + addi r3,r3,L1_CACHE_BYTES + bdnz 1b + sync /* wait for dcbst's to get to ram */ + mtctr r4 +2: icbi 0,r6 + addi r6,r6,L1_CACHE_BYTES + bdnz 2b + sync /* additional sync needed on g4 */ + isync + blr + +/* + * Write any modified data cache blocks out to memory. + * Does not invalidate the corresponding cache lines (especially for + * any corresponding instruction cache). + * + * clean_dcache_range(unsigned long start, unsigned long stop) + */ +_GLOBAL(clean_dcache_range) + li r5,L1_CACHE_BYTES-1 + andc r3,r3,r5 + subf r4,r3,r4 + add r4,r4,r5 + srwi. r4,r4,L1_CACHE_SHIFT + beqlr + mtctr r4 + +1: dcbst 0,r3 + addi r3,r3,L1_CACHE_BYTES + bdnz 1b + sync /* wait for dcbst's to get to ram */ + blr + +/* + * Write any modified data cache blocks out to memory and invalidate them. + * Does not invalidate the corresponding instruction cache blocks. + * + * flush_dcache_range(unsigned long start, unsigned long stop) + */ +_GLOBAL(flush_dcache_range) + li r5,L1_CACHE_BYTES-1 + andc r3,r3,r5 + subf r4,r3,r4 + add r4,r4,r5 + srwi. r4,r4,L1_CACHE_SHIFT + beqlr + mtctr r4 + +1: dcbf 0,r3 + addi r3,r3,L1_CACHE_BYTES + bdnz 1b + sync /* wait for dcbst's to get to ram */ + blr + +/* + * Like above, but invalidate the D-cache. This is used by the 8xx + * to invalidate the cache so the PPC core doesn't get stale data + * from the CPM (no cache snooping here :-). + * + * invalidate_dcache_range(unsigned long start, unsigned long stop) + */ +_GLOBAL(invalidate_dcache_range) + li r5,L1_CACHE_BYTES-1 + andc r3,r3,r5 + subf r4,r3,r4 + add r4,r4,r5 + srwi. r4,r4,L1_CACHE_SHIFT + beqlr + mtctr r4 + +1: dcbi 0,r3 + addi r3,r3,L1_CACHE_BYTES + bdnz 1b + sync /* wait for dcbi's to get to ram */ + blr + +/* + * 40x cores have 8K or 16K dcache and 32 byte line size. + * 44x has a 32K dcache and 32 byte line size. + * 8xx has 1, 2, 4, 8K variants. + * For now, cover the worst case of the 44x. + * Must be called with external interrupts disabled. + */ +#define CACHE_NWAYS 64 +#define CACHE_NLINES 32 + +_GLOBAL(flush_dcache) + li r4,(2 * CACHE_NWAYS * CACHE_NLINES) + mtctr r4 + lis r5,0 +1: lwz r3,0(r5) /* Load one word from every line */ + addi r5,r5,L1_CACHE_BYTES + bdnz 1b + sync + blr + +_GLOBAL(invalidate_dcache) + addi r6,0,0x0000 /* clear GPR 6 */ + /* Do loop for # of dcache congruence classes. */ + lis r7,(CFG_DCACHE_SIZE / L1_CACHE_BYTES / 2)@ha /* TBS for large sized cache */ + ori r7,r7,(CFG_DCACHE_SIZE / L1_CACHE_BYTES / 2)@l + /* NOTE: dccci invalidates both */ + mtctr r7 /* ways in the D cache */ +..dcloop: + dccci 0,r6 /* invalidate line */ + addi r6,r6,L1_CACHE_BYTES /* bump to next line */ + bdnz ..dcloop + sync + blr + +/* + * Cache functions. + * + * NOTE: currently the 440s run with dcache _disabled_ once relocated to DRAM, + * although for some cache-ralated calls stubs have to be provided to satisfy + * symbols resolution. + * Icache-related functions are used in POST framework. + * + */ +#ifdef CONFIG_440 + + .globl dcache_disable + .globl icache_disable + .globl icache_enable +dcache_disable: +icache_disable: +icache_enable: + blr + + .globl dcache_status + .globl icache_status +dcache_status: +icache_status: + mr r3, 0 + blr + +#else /* CONFIG_440 */ + + .globl icache_enable +icache_enable: + mflr r8 + bl invalidate_icache + mtlr r8 + isync + addis r3,r0, 0xc000 /* set bit 0 */ + mticcr r3 + blr + + .globl icache_disable +icache_disable: + addis r3,r0, 0x0000 /* clear bit 0 */ + mticcr r3 + isync + blr + + .globl icache_status +icache_status: + mficcr r3 + srwi r3, r3, 31 /* >>31 => select bit 0 */ + blr + + .globl dcache_enable +dcache_enable: + mflr r8 + bl invalidate_dcache + mtlr r8 + isync + addis r3,r0, 0x8000 /* set bit 0 */ + mtdccr r3 + blr + + .globl dcache_disable +dcache_disable: + mflr r8 + bl flush_dcache + mtlr r8 + addis r3,r0, 0x0000 /* clear bit 0 */ + mtdccr r3 + blr + + .globl dcache_status +dcache_status: + mfdccr r3 + srwi r3, r3, 31 /* >>31 => select bit 0 */ + blr + +#endif /* CONFIG_440 */ diff --git a/cpu/ppc4xx/kgdb.S b/cpu/ppc4xx/kgdb.S index 8c4bbf2e4de..42b9546d3d2 100644 --- a/cpu/ppc4xx/kgdb.S +++ b/cpu/ppc4xx/kgdb.S @@ -56,21 +56,21 @@ kgdb_flush_cache_all: .globl kgdb_flush_cache_range kgdb_flush_cache_range: - li r5,CFG_CACHELINE_SIZE-1 + li r5,L1_CACHE_BYTES-1 andc r3,r3,r5 subf r4,r3,r4 add r4,r4,r5 - srwi. r4,r4,CFG_CACHELINE_SHIFT + srwi. r4,r4,L1_CACHE_SHIFT beqlr mtctr r4 mr r6,r3 1: dcbst 0,r3 - addi r3,r3,CFG_CACHELINE_SIZE + addi r3,r3,L1_CACHE_BYTES bdnz 1b sync /* wait for dcbst's to get to ram */ mtctr r4 2: icbi 0,r6 - addi r6,r6,CFG_CACHELINE_SIZE + addi r6,r6,L1_CACHE_BYTES bdnz 2b SYNC blr diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 81a15fe922d..f5a135f1a01 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -1220,111 +1220,6 @@ mck_return: #endif /* CONFIG_440 */ -/* - * Cache functions. - * - * NOTE: currently the 440s run with dcache _disabled_ once relocated to DRAM, - * although for some cache-ralated calls stubs have to be provided to satisfy - * symbols resolution. - * Icache-related functions are used in POST framework. - * - */ -#ifdef CONFIG_440 - .globl dcache_disable - .globl icache_disable - .globl icache_enable -dcache_disable: -icache_disable: -icache_enable: - blr - - .globl dcache_status - .globl icache_status -dcache_status: -icache_status: - mr r3, 0 - blr -#else -flush_dcache: - addis r9,r0,0x0002 /* set mask for EE and CE msr bits */ - ori r9,r9,0x8000 - mfmsr r12 /* save msr */ - andc r9,r12,r9 - mtmsr r9 /* disable EE and CE */ - addi r10,r0,0x0001 /* enable data cache for unused memory */ - mfdccr r9 /* region 0xF8000000-0xFFFFFFFF via */ - or r10,r10,r9 /* bit 31 in dccr */ - mtdccr r10 - - /* do loop for # of congruence classes. */ - lis r10,(CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha /* TBS: for large cache sizes */ - ori r10,r10,(CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l - lis r11,(CFG_DCACHE_SIZE / 2)@ha /* D cache set size - 2 way sets */ - ori r11,r11,(CFG_DCACHE_SIZE / 2)@l /* D cache set size - 2 way sets */ - mtctr r10 - addi r10,r0,(0xE000-0x10000) /* start at 0xFFFFE000 */ - add r11,r10,r11 /* add to get to other side of cache line */ -..flush_dcache_loop: - lwz r3,0(r10) /* least recently used side */ - lwz r3,0(r11) /* the other side */ - dccci r0,r11 /* invalidate both sides */ - addi r10,r10,CFG_CACHELINE_SIZE /* bump to next line */ - addi r11,r11,CFG_CACHELINE_SIZE /* bump to next line */ - bdnz ..flush_dcache_loop - sync /* allow memory access to complete */ - mtdccr r9 /* restore dccr */ - mtmsr r12 /* restore msr */ - blr - - .globl icache_enable -icache_enable: - mflr r8 - bl invalidate_icache - mtlr r8 - isync - addis r3,r0, 0xc000 /* set bit 0 */ - mticcr r3 - blr - - .globl icache_disable -icache_disable: - addis r3,r0, 0x0000 /* clear bit 0 */ - mticcr r3 - isync - blr - - .globl icache_status -icache_status: - mficcr r3 - srwi r3, r3, 31 /* >>31 => select bit 0 */ - blr - - .globl dcache_enable -dcache_enable: - mflr r8 - bl invalidate_dcache - mtlr r8 - isync - addis r3,r0, 0x8000 /* set bit 0 */ - mtdccr r3 - blr - - .globl dcache_disable -dcache_disable: - mflr r8 - bl flush_dcache - mtlr r8 - addis r3,r0, 0x0000 /* clear bit 0 */ - mtdccr r3 - blr - - .globl dcache_status -dcache_status: - mfdccr r3 - srwi r3, r3, 31 /* >>31 => select bit 0 */ - blr -#endif - .globl get_pvr get_pvr: mfspr r3, PVR @@ -1430,6 +1325,26 @@ ppcSync: */ .globl relocate_code relocate_code: +#ifdef CONFIG_4xx_DCACHE + /* + * We need to flush the Init Data before the dcache will be + * invalidated + */ + + /* save regs */ + mr r9,r3 + mr r10,r4 + mr r11,r5 + + mr r3,r4 + addi r4,r4,0x200 /* should be enough for init data */ + bl flush_dcache_range + + /* restore regs */ + mr r3,r9 + mr r4,r10 + mr r5,r11 +#endif #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) @@ -1457,7 +1372,7 @@ relocate_code: ori r4, r4, CFG_MONITOR_BASE@l lwz r5, GOT(__init_end) sub r5, r5, r4 - li r6, CFG_CACHELINE_SIZE /* Cache Line Size */ + li r6, L1_CACHE_BYTES /* Cache Line Size */ /* * Fix GOT pointer: @@ -1777,23 +1692,6 @@ in32: lwz 3,0x0000(3) blr -invalidate_icache: - iccci r0,r0 /* for 405, iccci invalidates the */ - blr /* entire I cache */ - -invalidate_dcache: - addi r6,0,0x0000 /* clear GPR 6 */ - /* Do loop for # of dcache congruence classes. */ - lis r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha /* TBS for large sized cache */ - ori r7, r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l - /* NOTE: dccci invalidates both */ - mtctr r7 /* ways in the D cache */ -..dcloop: - dccci 0,r6 /* invalidate line */ - addi r6,r6, CFG_CACHELINE_SIZE /* bump to next line */ - bdnz ..dcloop - blr - /**************************************************************************/ /* PPC405EP specific stuff */ /**************************************************************************/ diff --git a/include/asm-ppc/cache.h b/include/asm-ppc/cache.h index 5befab4d536..e29bfc2a7b4 100644 --- a/include/asm-ppc/cache.h +++ b/include/asm-ppc/cache.h @@ -8,15 +8,24 @@ #include /* bytes per L1 cache line */ -#if !defined(CONFIG_8xx) || defined(CONFIG_8260) +#if !(defined(CONFIG_8xx) || defined(CONFIG_IOP480)) #if defined(CONFIG_PPC64BRIDGE) -#define L1_CACHE_BYTES 128 +#define L1_CACHE_SHIFT 7 #else -#define L1_CACHE_BYTES 32 +#define L1_CACHE_SHIFT 5 #endif /* PPC64 */ #else -#define L1_CACHE_BYTES 16 -#endif /* !8xx || 8260 */ +#define L1_CACHE_SHIFT 4 +#endif /* !(8xx || IOP480) */ + +#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT) + +/* + * For compatibility reasons support the CFG_CACHELINE_SIZE too + */ +#ifndef CFG_CACHELINE_SIZE +#define CFG_CACHELINE_SIZE L1_CACHE_BYTES +#endif #define L1_CACHE_ALIGN(x) (((x)+(L1_CACHE_BYTES-1))&~(L1_CACHE_BYTES-1)) #define L1_CACHE_PAGES 8 @@ -35,6 +44,8 @@ extern void flush_dcache_range(unsigned long start, unsigned long stop); extern void clean_dcache_range(unsigned long start, unsigned long stop); extern void invalidate_dcache_range(unsigned long start, unsigned long stop); +extern void flush_dcache(void); +extern void invalidate_dcache(void); #ifdef CFG_INIT_RAM_LOCK extern void unlock_ram_in_cache(void); #endif /* CFG_INIT_RAM_LOCK */ diff --git a/include/ppc405.h b/include/ppc405.h index 97528e88a82..2c5591726c3 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -22,6 +22,12 @@ #ifndef __PPC405_H__ #define __PPC405_H__ +#ifndef CONFIG_IOP480 +#define CFG_DCACHE_SIZE (16 << 10) /* For AMCC 405 CPUs */ +#else +#define CFG_DCACHE_SIZE (2 << 10) /* For PLX IOP480 (403) */ +#endif + /*--------------------------------------------------------------------- */ /* Special Purpose Registers */ /*--------------------------------------------------------------------- */ diff --git a/include/ppc440.h b/include/ppc440.h index dc5eb98c909..2f841fa6bc6 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -22,6 +22,8 @@ #ifndef __PPC440_H__ #define __PPC440_H__ +#define CFG_DCACHE_SIZE (32 << 10) /* For AMCC 440 CPUs */ + /*--------------------------------------------------------------------- */ /* Special Purpose Registers */ /*--------------------------------------------------------------------- */ @@ -3282,8 +3284,4 @@ static inline void set_mcsr(u32 val) #endif /* _ASMLANGUAGE */ -#define RESET_VECTOR 0xfffffffc -#define CACHELINE_MASK (CFG_CACHELINE_SIZE - 1) /* Address mask for */ - /* cache line aligned data. */ - #endif /* __PPC440_H__ */ diff --git a/lib_ppc/cache.c b/lib_ppc/cache.c index a81ab5e363f..27e1a823c61 100644 --- a/lib_ppc/cache.c +++ b/lib_ppc/cache.c @@ -22,7 +22,7 @@ */ #include - +#include void flush_cache (ulong start_addr, ulong size) { -- cgit v1.3.1 From d25dfe08fbd1220cb994e7e6b105049aa9aa8e79 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 31 Oct 2007 17:57:52 +0100 Subject: ppc4xx: Remove cache definition from 4xx board config files All 4xx board config files don't need the cache definitions anymore. These are now defined in common headers. Signed-off-by: Stefan Roese --- include/configs/ADCIOP.h | 9 --------- include/configs/AP1000.h | 8 -------- include/configs/AR405.h | 10 ---------- include/configs/ASH405.h | 10 ---------- include/configs/CANBT.h | 9 --------- include/configs/CMS700.h | 10 ---------- include/configs/CPCI2DP.h | 10 ---------- include/configs/CPCI405.h | 9 --------- include/configs/CPCI4052.h | 10 ---------- include/configs/CPCI405AB.h | 10 ---------- include/configs/CPCI405DT.h | 10 ---------- include/configs/CPCI440.h | 9 --------- include/configs/CPCIISER4.h | 9 --------- include/configs/CRAYL1.h | 6 ------ include/configs/DASA_SIM.h | 9 --------- include/configs/DP405.h | 10 ---------- include/configs/DU405.h | 9 --------- include/configs/ERIC.h | 8 -------- include/configs/EXBITGEN.h | 4 ---- include/configs/G2000.h | 10 ---------- include/configs/HH405.h | 10 ---------- include/configs/HUB405.h | 10 ---------- include/configs/JSE.h | 9 --------- include/configs/KAREF.h | 8 -------- include/configs/METROBOX.h | 8 -------- include/configs/MIP405.h | 9 --------- include/configs/ML2.h | 8 -------- include/configs/OCRTC.h | 9 --------- include/configs/ORSG.h | 9 --------- include/configs/PCI405.h | 9 --------- include/configs/PIP405.h | 9 --------- include/configs/PLU405.h | 10 ---------- include/configs/PMC405.h | 10 ---------- include/configs/PPChameleonEVB.h | 10 ---------- include/configs/VOH405.h | 10 ---------- include/configs/VOM405.h | 10 ---------- include/configs/W7OLMC.h | 9 --------- include/configs/W7OLMG.h | 9 --------- include/configs/WUH405.h | 10 ---------- include/configs/XPEDITE1K.h | 8 -------- include/configs/acadia.h | 9 --------- include/configs/alpr.h | 6 ------ include/configs/bamboo.h | 9 --------- include/configs/bubinga.h | 8 -------- include/configs/csb272.h | 8 -------- include/configs/csb472.h | 8 -------- include/configs/ebony.h | 8 -------- include/configs/hcu4.h | 7 ------- include/configs/hcu5.h | 7 ------- include/configs/katmai.h | 8 -------- include/configs/kilauea.h | 9 --------- include/configs/luan.h | 9 --------- include/configs/lwmon5.h | 9 --------- include/configs/makalu.h | 9 --------- include/configs/ml300.h | 6 ------ include/configs/ocotea.h | 8 -------- include/configs/p3p440.h | 8 -------- include/configs/pcs440ep.h | 9 --------- include/configs/sbc405.h | 10 ---------- include/configs/sc3.h | 18 ------------------ include/configs/sequoia.h | 17 ++++++++--------- include/configs/taihu.h | 7 ------- include/configs/taishan.h | 9 --------- include/configs/walnut.h | 10 ---------- include/configs/yosemite.h | 9 --------- include/configs/yucca.h | 8 -------- include/configs/zeus.h | 7 ------- 67 files changed, 8 insertions(+), 595 deletions(-) (limited to 'include') diff --git a/include/configs/ADCIOP.h b/include/configs/ADCIOP.h index 46329918ef1..5d28168fbcb 100644 --- a/include/configs/ADCIOP.h +++ b/include/configs/ADCIOP.h @@ -191,15 +191,6 @@ #define CFG_ETH_DEV_FN 0x0000 #define CFG_ETH_IOBASE 0x0fff0000 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */ -#define CFG_CACHELINE_SIZE 16 /* For AMCC 401/403 CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h index d25aa74a452..d490b33bd4c 100644 --- a/include/configs/AP1000.h +++ b/include/configs/AP1000.h @@ -193,14 +193,6 @@ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Init Memory Controller: diff --git a/include/configs/AR405.h b/include/configs/AR405.h index 0f301ec0c6a..50f09b03f3b 100644 --- a/include/configs/AR405.h +++ b/include/configs/AR405.h @@ -213,16 +213,6 @@ #define CFG_ENV_ADDR_REDUND 0xFFFA0000 #define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 9adbba95441..85c6a992d7b 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -258,16 +258,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h index ae32f6b14ac..7029dbddef2 100644 --- a/include/configs/CANBT.h +++ b/include/configs/CANBT.h @@ -181,15 +181,6 @@ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index 21cd9c1f261..285cd5c0e8e 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -272,16 +272,6 @@ #define CFG_EEPROM_WREN 1 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h index a3717b9052f..58900c3091d 100644 --- a/include/configs/CPCI2DP.h +++ b/include/configs/CPCI2DP.h @@ -223,16 +223,6 @@ #define CFG_EEPROM_WREN 1 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 1b948f6382a..bd43e1dc9aa 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -266,15 +266,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index fb71c5fb040..b248639fd0d 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -317,16 +317,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 49943195b72..1e9597dc619 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -288,16 +288,6 @@ #define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ #define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index 29f92924478..a8029eae9d1 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -319,16 +319,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h index 318ada1a4fb..eb47cd7ff82 100644 --- a/include/configs/CPCI440.h +++ b/include/configs/CPCI440.h @@ -262,15 +262,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* Configuration Port location */ #define CONFIG_PORT_ADDR 0xF0000500 diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h index c7b623a1d6d..78b754c19df 100644 --- a/include/configs/CPCIISER4.h +++ b/include/configs/CPCIISER4.h @@ -205,15 +205,6 @@ #define CFG_ENV_SIZE 0x300 /* 768 bytes may be used for env vars */ /* total size of a CAT24WC08 is 1024 bytes */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h index a965c125f3f..2356858d8c7 100644 --- a/include/configs/CRAYL1.h +++ b/include/configs/CRAYL1.h @@ -192,12 +192,6 @@ #define CFG_MEMTEST_END (CFG_SDRAM_SIZE * 1024 * 1024 - CFG_MEM_END_USAGE) /* END ENVIRONNEMENT FLASH */ -/*----------------------------------------------------------------------- - * Cache Configuration. Only used to ..?? clear it, I guess.. - */ -#define CFG_DCACHE_SIZE 16384 -#define CFG_CACHELINE_SIZE 32 - /* * Init Memory Controller: * diff --git a/include/configs/DASA_SIM.h b/include/configs/DASA_SIM.h index 627ea14826b..117a1367c1d 100644 --- a/include/configs/DASA_SIM.h +++ b/include/configs/DASA_SIM.h @@ -182,15 +182,6 @@ #define CFG_PCI9054_DEV_FN 0x0800 #define CFG_PCI9054_IOBASE 0x0eff0000 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 2048 /* For PLX IOP480 */ -#define CFG_CACHELINE_SIZE 16 /* For AMCC 401/403 CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/DP405.h b/include/configs/DP405.h index 2eadbea35d6..912fb2af1c0 100644 --- a/include/configs/DP405.h +++ b/include/configs/DP405.h @@ -241,16 +241,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/DU405.h b/include/configs/DU405.h index 5c595f57d26..c8bf67fe964 100644 --- a/include/configs/DU405.h +++ b/include/configs/DU405.h @@ -232,15 +232,6 @@ #define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */ /* total size of a CAT24WC08 is 1024 bytes */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/ERIC.h b/include/configs/ERIC.h index 5d48d2bbb68..dc15b0c3498 100644 --- a/include/configs/ERIC.h +++ b/include/configs/ERIC.h @@ -323,14 +323,6 @@ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Init Memory Controller: diff --git a/include/configs/EXBITGEN.h b/include/configs/EXBITGEN.h index a3f38bb3a32..251227c7ff2 100644 --- a/include/configs/EXBITGEN.h +++ b/include/configs/EXBITGEN.h @@ -205,10 +205,6 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -/* Cache configuration */ -#define CFG_DCACHE_SIZE 8192 -#define CFG_CACHELINE_SIZE 32 - /* * Internal Definitions * diff --git a/include/configs/G2000.h b/include/configs/G2000.h index 9c713c6c26f..c12ce48b6f3 100644 --- a/include/configs/G2000.h +++ b/include/configs/G2000.h @@ -330,16 +330,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 8967b3fc601..18e5b3c2883 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -362,16 +362,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h index 1ff71081302..a389d582dfc 100644 --- a/include/configs/HUB405.h +++ b/include/configs/HUB405.h @@ -257,16 +257,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/JSE.h b/include/configs/JSE.h index ea3b0b4a325..5b40ef6b42f 100644 --- a/include/configs/JSE.h +++ b/include/configs/JSE.h @@ -279,15 +279,6 @@ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405GPr CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h index 3644e43885e..816e63ba2ab 100644 --- a/include/configs/KAREF.h +++ b/include/configs/KAREF.h @@ -281,14 +281,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above */ -#endif /* * Internal Definitions diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h index 8d7ec5926bc..d61b49eeecd 100644 --- a/include/configs/METROBOX.h +++ b/include/configs/METROBOX.h @@ -346,14 +346,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above */ -#endif /* * Internal Definitions diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h index 5b526a0993f..9ddf82b3e06 100644 --- a/include/configs/MIP405.h +++ b/include/configs/MIP405.h @@ -257,15 +257,6 @@ #define MTDPARTS_DEFAULT "mtdparts=mip405-0:-(jffs2)" */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 0x4000 /* For AMCC 405GPr CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * Logbuffer Configuration */ diff --git a/include/configs/ML2.h b/include/configs/ML2.h index f488275f239..66dae21924d 100644 --- a/include/configs/ML2.h +++ b/include/configs/ML2.h @@ -201,14 +201,6 @@ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Init Memory Controller: diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h index 5840ea25f4b..94b5bc965e0 100644 --- a/include/configs/OCRTC.h +++ b/include/configs/OCRTC.h @@ -222,15 +222,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h index 937df229f16..4e030885fea 100644 --- a/include/configs/ORSG.h +++ b/include/configs/ORSG.h @@ -220,15 +220,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h index d6e7082f6a9..e70c0d3d4d6 100644 --- a/include/configs/PCI405.h +++ b/include/configs/PCI405.h @@ -251,15 +251,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index efa015746e1..b83520d7c1f 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -231,15 +231,6 @@ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: */ diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 652210c19da..6b166540422 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -299,16 +299,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h index b29f368f57c..adbe8a9fba6 100644 --- a/include/configs/PMC405.h +++ b/include/configs/PMC405.h @@ -269,16 +269,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 8a74c4f5c90..c2aa2cc0984 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -454,16 +454,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 14848abe5b2..3a413f555dc 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -305,16 +305,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h index 5512f4be21a..ec6f205540c 100644 --- a/include/configs/VOM405.h +++ b/include/configs/VOM405.h @@ -247,16 +247,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h index fc177fb1f56..7017fff5de7 100644 --- a/include/configs/W7OLMC.h +++ b/include/configs/W7OLMC.h @@ -290,15 +290,6 @@ */ #define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above val. */ -#endif - /* * Init Memory Controller: */ diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h index 20d693fa478..bfb3156f6f6 100644 --- a/include/configs/W7OLMG.h +++ b/include/configs/W7OLMG.h @@ -293,15 +293,6 @@ */ #define SPD_EEPROM_ADDRESS 0x50 /* XXX conflicting address!!! XXX */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above val. */ -#endif - /* * Init Memory Controller: */ diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h index 656784aa0cc..582d8cf8640 100644 --- a/include/configs/WUH405.h +++ b/include/configs/WUH405.h @@ -254,16 +254,6 @@ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/XPEDITE1K.h b/include/configs/XPEDITE1K.h index 611f5a62caa..38ea576a6e8 100644 --- a/include/configs/XPEDITE1K.h +++ b/include/configs/XPEDITE1K.h @@ -257,14 +257,6 @@ extern void out32(unsigned int, unsigned long); * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 440GX CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/acadia.h b/include/configs/acadia.h index e3f6e2c8b34..dc322dd55b0 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -384,15 +384,6 @@ #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EZ CPU */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value*/ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ diff --git a/include/configs/alpr.h b/include/configs/alpr.h index d88c3ad43b0..aff9823d559 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -355,12 +355,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ /* * Internal Definitions diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 14c563808bb..d57744855c8 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -414,15 +414,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 7736a1e32d0..eca195a9f75 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -321,14 +321,6 @@ #define CFG_ENV_ADDR \ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405EP CPU */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Init Memory Controller: diff --git a/include/configs/csb272.h b/include/configs/csb272.h index c43b49737d9..a24478d0b39 100644 --- a/include/configs/csb272.h +++ b/include/configs/csb272.h @@ -289,14 +289,6 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -/* - * Cache configuration - * - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 - /* * Miscellaneous board specific definitions * diff --git a/include/configs/csb472.h b/include/configs/csb472.h index a7120aa57f9..064650cfca7 100644 --- a/include/configs/csb472.h +++ b/include/configs/csb472.h @@ -288,14 +288,6 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -/* - * Cache configuration - * - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 - /* * Miscellaneous board specific definitions * diff --git a/include/configs/ebony.h b/include/configs/ebony.h index 2c626a03288..5faa9ebcda1 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -293,14 +293,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/hcu4.h b/include/configs/hcu4.h index 577f459e29e..b43b228fba9 100644 --- a/include/configs/hcu4.h +++ b/include/configs/hcu4.h @@ -321,13 +321,6 @@ #define CONFIG_PORT_ADDR 0xF0000500 -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405GPr CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ - /* * Internal Definitions * diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h index 90858819b67..1214bc31b59 100644 --- a/include/configs/hcu5.h +++ b/include/configs/hcu5.h @@ -364,13 +364,6 @@ #define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 ) #define HCU_HW_VERSION_REGISTER ( CFG_CPLD + 0x1400000 ) -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ - /* * Internal Definitions * diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 5da00fc8e55..2eed9413f66 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -431,14 +431,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 9a9f7ba1bc2..caf8b5287a5 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -329,15 +329,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */ -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ diff --git a/include/configs/luan.h b/include/configs/luan.h index a09dd74733e..cba7295fe97 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -293,15 +293,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 52deab43f15..3180617b1e0 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -487,15 +487,6 @@ } \ } -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 3e3b008c6eb..30707799f5c 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -318,15 +318,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE (16 << 10) /* For IBM 405EX */ -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ diff --git a/include/configs/ml300.h b/include/configs/ml300.h index 0183041842a..1945918300c 100644 --- a/include/configs/ml300.h +++ b/include/configs/ml300.h @@ -159,12 +159,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) */ diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h index bc2fd33ff5e..fd4d3affe99 100644 --- a/include/configs/ocotea.h +++ b/include/configs/ocotea.h @@ -317,14 +317,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h index 51f19a1456c..255e0727cc3 100644 --- a/include/configs/p3p440.h +++ b/include/configs/p3p440.h @@ -311,14 +311,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 7653ba1d245..d467338e920 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -438,15 +438,6 @@ } \ } -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h index dc906b15006..60d401fa0e5 100644 --- a/include/configs/sbc405.h +++ b/include/configs/sbc405.h @@ -233,16 +233,6 @@ #define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */ #define CFG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/sc3.h b/include/configs/sc3.h index cb225369871..0a03c0ecefa 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -433,24 +433,6 @@ extern unsigned long offsetOfEnvironment; #define CONFIG_JFFS2_PART_SIZE 0x01000000 #define CONFIG_JFFS2_PART_OFFSET 0x00000000 -/*----------------------------------------------------------------------- - * Cache Configuration - * - * CFG_DCACHE_SIZE -> size of data cache: - * - 405GP 8k - * - 405GPr 16k - * How to handle the difference in chache size? - * CFG_CACHELINE_SIZE -> size of one cache line: 32 bytes - * (used in cpu/ppc4xx/start.S) -*/ -#define CFG_DCACHE_SIZE 16384 - -#define CFG_CACHELINE_SIZE 32 - -#if defined(CONFIG_CMD_KGDB) - #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Init Memory Controller: * diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 600f98cf0d4..72f01d90fd2 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -43,6 +43,14 @@ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ 33333333 : 33000000) +#if 0 +/* + * 44x dcache supported is working now on sequoia, but we don't enable + * it yet since it needs further testing + */ +#define CONFIG_4xx_DCACHE /* enable dcache */ +#endif + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -460,15 +468,6 @@ #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/taihu.h b/include/configs/taihu.h index 6d204a9b575..c51468b6c8e 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -366,13 +366,6 @@ unsigned char spi_read(void); } \ } -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */ -#define CFG_CACHELINE_SIZE 32 -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ - /* * Init Memory Controller: * diff --git a/include/configs/taishan.h b/include/configs/taishan.h index baa4fbd312b..ab3b0c1acba 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -319,15 +319,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * Cache Configuration - *----------------------------------------------------------------------*/ -#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/walnut.h b/include/configs/walnut.h index 180549efad3..19b29e71d11 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -289,16 +289,6 @@ (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */ #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For AMCC 405 CPUs, older 405 ppc's */ - /* have only 8kB, 16kB is save here */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup */ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 35bce4af904..2dde9bee30e 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -361,15 +361,6 @@ #define CFG_BCSR5_PCI66EN 0x80 -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 2b4024dfd97..db1d35bdd75 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -324,14 +324,6 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif /* * Internal Definitions diff --git a/include/configs/zeus.h b/include/configs/zeus.h index 605755a87e8..810a528d249 100644 --- a/include/configs/zeus.h +++ b/include/configs/zeus.h @@ -236,13 +236,6 @@ #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 16384 /* For IBM 405EP CPU */ -#define CFG_CACHELINE_SIZE 32 /* ... */ -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ - /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in data cache) */ -- cgit v1.3.1 From 483e09a223c666269ef81d3573a6591b1046b0ef Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 31 Oct 2007 17:59:22 +0100 Subject: ppc4xx: Add change_tlb function to modify I attribute of TLB(s) This function is used to either turn cache on or off in a specific memory area. Signed-off-by: Stefan Roese --- cpu/ppc4xx/tlb.c | 88 ++++++++++++++++++++++++++++++++++++++++++++++++++- include/asm-ppc/mmu.h | 1 + 2 files changed, 88 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/cpu/ppc4xx/tlb.c b/cpu/ppc4xx/tlb.c index 098694caf49..ed493f1a710 100644 --- a/cpu/ppc4xx/tlb.c +++ b/cpu/ppc4xx/tlb.c @@ -26,6 +26,7 @@ #if defined(CONFIG_440) #include +#include #include #include @@ -42,7 +43,6 @@ void remove_tlb(u32 vaddr, u32 size) u32 tlb_vaddr; u32 tlb_size = 0; - /* First, find the index of a TLB entry not being used */ for (i=0; i= vaddr)) { + /* + * TLB is enabled and start address is lower or equal + * than the area we are looking for. Now we only have + * to check the size/end address for a match. + */ + switch (tlb_word0_value & TLB_WORD0_SIZE_MASK) { + case TLB_WORD0_SIZE_1KB: + tlb_size = 1 << 10; + break; + case TLB_WORD0_SIZE_4KB: + tlb_size = 4 << 10; + break; + case TLB_WORD0_SIZE_16KB: + tlb_size = 16 << 10; + break; + case TLB_WORD0_SIZE_64KB: + tlb_size = 64 << 10; + break; + case TLB_WORD0_SIZE_256KB: + tlb_size = 256 << 10; + break; + case TLB_WORD0_SIZE_1MB: + tlb_size = 1 << 20; + break; + case TLB_WORD0_SIZE_16MB: + tlb_size = 16 << 20; + break; + case TLB_WORD0_SIZE_256MB: + tlb_size = 256 << 20; + break; + } + + /* + * Now check the end-address if it's in the range + */ + if ((tlb_vaddr + tlb_size - 1) <= (vaddr + size - 1)) { + /* + * Found a TLB in the range. + * Change cache attribute in tlb2 word. + */ + tlb_word2_value = + TLB_WORD2_U0_DISABLE | TLB_WORD2_U1_DISABLE | + TLB_WORD2_U2_DISABLE | TLB_WORD2_U3_DISABLE | + TLB_WORD2_W_DISABLE | tlb_word2_i_value | + TLB_WORD2_M_DISABLE | TLB_WORD2_G_DISABLE | + TLB_WORD2_E_DISABLE | TLB_WORD2_UX_ENABLE | + TLB_WORD2_UW_ENABLE | TLB_WORD2_UR_ENABLE | + TLB_WORD2_SX_ENABLE | TLB_WORD2_SW_ENABLE | + TLB_WORD2_SR_ENABLE; + + /* + * Now either flush or invalidate the dcache + */ + if (tlb_word2_i_value) + flush_dcache(); + else + invalidate_dcache(); + + mttlb3(i, tlb_word2_value); + asm("iccci 0,0"); + } + } + } + + /* Execute an ISYNC instruction so that the new TLB entry takes effect */ + asm("isync"); +} + static int add_tlb_entry(unsigned long phys_addr, unsigned long virt_addr, unsigned long tlb_word0_size_value, diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h index b3cfa9b3726..edcb3b9ca37 100644 --- a/include/asm-ppc/mmu.h +++ b/include/asm-ppc/mmu.h @@ -648,6 +648,7 @@ unsigned long mftlb3(unsigned long index); void program_tlb(u32 phys_addr, u32 virt_addr, u32 size, u32 tlb_word2_i_value); void remove_tlb(u32 vaddr, u32 size); +void change_tlb(u32 vaddr, u32 size, u32 tlb_word2_i_value); #endif /* __ASSEMBLY__ */ #endif /* CONFIG_440 */ -- cgit v1.3.1 From ff768cb168d8157c24a25016dbfbeb465e47f420 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 31 Oct 2007 18:01:24 +0100 Subject: ppc4xx: Change 4xx ethernet driver to handle cached memory too This patch enables the 4xx EMAC driver to work too, when dcache is enabled. Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_enet.c | 137 +++++++++++++++++++++++--------------------------- include/ppc4xx_enet.h | 2 + 2 files changed, 64 insertions(+), 75 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 697e038d5eb..c08bf61e480 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -82,6 +82,8 @@ #include #include #include +#include +#include #include #include #include @@ -189,6 +191,10 @@ struct eth_device *emac0_dev = NULL; #define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * 2)) #endif +#define MAL_RX_DESC_SIZE 2048 +#define MAL_TX_DESC_SIZE 2048 +#define MAL_ALLOC_SIZE (MAL_TX_DESC_SIZE + MAL_RX_DESC_SIZE) + /*-----------------------------------------------------------------------------+ * Prototypes and externals. *-----------------------------------------------------------------------------*/ @@ -354,8 +360,8 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) /* Ensure we setup mdio for this devnum and ONLY this devnum */ zmiifer |= (ZMII_FER_MDI) << ZMII_FER_V(devnum); - out_be32(ZMII_FER, zmiifer); - out_be32(RGMII_FER, rmiifer); + out_be32((void *)ZMII_FER, zmiifer); + out_be32((void *)RGMII_FER, rmiifer); return ((int)pfc1); } @@ -446,9 +452,15 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) } #endif /* CONFIG_405EX */ +static inline void *malloc_aligned(u32 size, u32 align) +{ + return (void *)(((u32)malloc(size + align) + align - 1) & + ~(align - 1)); +} + static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) { - int i, j; + int i; unsigned long reg = 0; unsigned long msr; unsigned long speed; @@ -473,6 +485,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) defined(CONFIG_405EX) unsigned long mfr; #endif + u32 bd_cached; + u32 bd_uncached = 0; EMAC_4XX_HW_PST hw_p = dev->priv; @@ -768,11 +782,11 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) #endif /* Set ZMII/RGMII speed according to the phy link speed */ - reg = in_be32(ZMII_SSR); + reg = in_be32((void *)ZMII_SSR); if ( (speed == 100) || (speed == 1000) ) - out_be32(ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum))); + out_be32((void *)ZMII_SSR, reg | (ZMII_SSR_SP << ZMII_SSR_V (devnum))); else - out_be32(ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); + out_be32((void *)ZMII_SSR, reg & (~(ZMII_SSR_SP << ZMII_SSR_V (devnum)))); if ((devnum == 2) || (devnum == 3)) { if (speed == 1000) @@ -785,7 +799,7 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) printf("Error in RGMII Speed\n"); return -1; } - out_be32(RGMII_SSR, reg); + out_be32((void *)RGMII_SSR, reg); } #endif /* defined(CONFIG_440) && !defined(CONFIG_440SP) */ @@ -819,91 +833,60 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) } #endif - /* Free "old" buffers */ - if (hw_p->alloc_tx_buf) - free (hw_p->alloc_tx_buf); - if (hw_p->alloc_rx_buf) - free (hw_p->alloc_rx_buf); - /* * Malloc MAL buffer desciptors, make sure they are * aligned on cache line boundary size * (401/403/IOP480 = 16, 405 = 32) * and doesn't cross cache block boundaries. */ - hw_p->alloc_tx_buf = - (mal_desc_t *) malloc ((sizeof (mal_desc_t) * NUM_TX_BUFF) + - ((2 * CFG_CACHELINE_SIZE) - 2)); - if (NULL == hw_p->alloc_tx_buf) - return -1; - if (((int) hw_p->alloc_tx_buf & CACHELINE_MASK) != 0) { - hw_p->tx = - (mal_desc_t *) ((int) hw_p->alloc_tx_buf + - CFG_CACHELINE_SIZE - - ((int) hw_p-> - alloc_tx_buf & CACHELINE_MASK)); - } else { - hw_p->tx = hw_p->alloc_tx_buf; - } + if (hw_p->first_init == 0) { + debug("*** Allocating descriptor memory ***\n"); - hw_p->alloc_rx_buf = - (mal_desc_t *) malloc ((sizeof (mal_desc_t) * NUM_RX_BUFF) + - ((2 * CFG_CACHELINE_SIZE) - 2)); - if (NULL == hw_p->alloc_rx_buf) { - free(hw_p->alloc_tx_buf); - hw_p->alloc_tx_buf = NULL; - return -1; - } + bd_cached = (u32)malloc_aligned(MAL_ALLOC_SIZE, 4096); + if (!bd_cached) { + printf("%s: Error allocating MAL descriptor buffers!\n"); + return -1; + } - if (((int) hw_p->alloc_rx_buf & CACHELINE_MASK) != 0) { - hw_p->rx = - (mal_desc_t *) ((int) hw_p->alloc_rx_buf + - CFG_CACHELINE_SIZE - - ((int) hw_p-> - alloc_rx_buf & CACHELINE_MASK)); - } else { - hw_p->rx = hw_p->alloc_rx_buf; +#ifdef CONFIG_4xx_DCACHE + flush_dcache_range(bd_cached, bd_cached + MAL_ALLOC_SIZE); + hw_p->tx_phys = bd_cached; + hw_p->rx_phys = bd_cached + MAL_TX_DESC_SIZE; + bd_uncached = bis->bi_memsize; + program_tlb(bd_cached, bd_uncached, MAL_ALLOC_SIZE, + TLB_WORD2_I_ENABLE); +#else + bd_uncached = bd_cached; +#endif + hw_p->tx_phys = bd_cached; + hw_p->rx_phys = bd_cached + MAL_TX_DESC_SIZE; + hw_p->tx = (mal_desc_t *)(bd_uncached); + hw_p->rx = (mal_desc_t *)(bd_uncached + MAL_TX_DESC_SIZE); + debug("hw_p->tx=%08x, hw_p->rx=%08x\n", hw_p->tx, hw_p->rx); } for (i = 0; i < NUM_TX_BUFF; i++) { hw_p->tx[i].ctrl = 0; hw_p->tx[i].data_len = 0; - if (hw_p->first_init == 0) { - hw_p->txbuf_ptr = - (char *) malloc (ENET_MAX_MTU_ALIGNED); - if (NULL == hw_p->txbuf_ptr) { - free(hw_p->alloc_rx_buf); - free(hw_p->alloc_tx_buf); - hw_p->alloc_rx_buf = NULL; - hw_p->alloc_tx_buf = NULL; - for(j = 0; j < i; j++) { - free(hw_p->tx[i].data_ptr); - hw_p->tx[i].data_ptr = NULL; - } - } - } + if (hw_p->first_init == 0) + hw_p->txbuf_ptr = malloc_aligned(MAL_ALLOC_SIZE, + L1_CACHE_BYTES); hw_p->tx[i].data_ptr = hw_p->txbuf_ptr; if ((NUM_TX_BUFF - 1) == i) hw_p->tx[i].ctrl |= MAL_TX_CTRL_WRAP; hw_p->tx_run[i] = -1; -#if 0 - printf ("TX_BUFF %d @ 0x%08lx\n", i, - (ulong) hw_p->tx[i].data_ptr); -#endif + debug("TX_BUFF %d @ 0x%08lx\n", i, (u32)hw_p->tx[i].data_ptr); } for (i = 0; i < NUM_RX_BUFF; i++) { hw_p->rx[i].ctrl = 0; hw_p->rx[i].data_len = 0; - /* rx[i].data_ptr = (char *) &rx_buff[i]; */ - hw_p->rx[i].data_ptr = (char *) NetRxPackets[i]; + hw_p->rx[i].data_ptr = (char *)NetRxPackets[i]; if ((NUM_RX_BUFF - 1) == i) hw_p->rx[i].ctrl |= MAL_RX_CTRL_WRAP; hw_p->rx[i].ctrl |= MAL_RX_CTRL_EMPTY | MAL_RX_CTRL_INTR; hw_p->rx_ready[i] = -1; -#if 0 - printf ("RX_BUFF %d @ 0x%08lx\n", i, (ulong) hw_p->rx[i].data_ptr); -#endif + debug("RX_BUFF %d @ 0x%08lx\n", i, (u32)hw_p->rx[i].data_ptr); } reg = 0x00000000; @@ -929,15 +912,15 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) case 1: /* setup MAL tx & rx channel pointers */ #if defined (CONFIG_405EP) || defined (CONFIG_440EP) || defined (CONFIG_440GR) - mtdcr (maltxctp2r, hw_p->tx); + mtdcr (maltxctp2r, hw_p->tx_phys); #else - mtdcr (maltxctp1r, hw_p->tx); + mtdcr (maltxctp1r, hw_p->tx_phys); #endif #if defined(CONFIG_440) mtdcr (maltxbattr, 0x0); mtdcr (malrxbattr, 0x0); #endif - mtdcr (malrxctp1r, hw_p->rx); + mtdcr (malrxctp1r, hw_p->rx_phys); /* set RX buffer size */ mtdcr (malrcbs1, ENET_MAX_MTU_ALIGNED / 16); break; @@ -946,17 +929,17 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) /* setup MAL tx & rx channel pointers */ mtdcr (maltxbattr, 0x0); mtdcr (malrxbattr, 0x0); - mtdcr (maltxctp2r, hw_p->tx); - mtdcr (malrxctp2r, hw_p->rx); + mtdcr (maltxctp2r, hw_p->tx_phys); + mtdcr (malrxctp2r, hw_p->rx_phys); /* set RX buffer size */ mtdcr (malrcbs2, ENET_MAX_MTU_ALIGNED / 16); break; case 3: /* setup MAL tx & rx channel pointers */ mtdcr (maltxbattr, 0x0); - mtdcr (maltxctp3r, hw_p->tx); + mtdcr (maltxctp3r, hw_p->tx_phys); mtdcr (malrxbattr, 0x0); - mtdcr (malrxctp3r, hw_p->rx); + mtdcr (malrxctp3r, hw_p->rx_phys); /* set RX buffer size */ mtdcr (malrcbs3, ENET_MAX_MTU_ALIGNED / 16); break; @@ -968,8 +951,8 @@ static int ppc_4xx_eth_init (struct eth_device *dev, bd_t * bis) mtdcr (maltxbattr, 0x0); mtdcr (malrxbattr, 0x0); #endif - mtdcr (maltxctp0r, hw_p->tx); - mtdcr (malrxctp0r, hw_p->rx); + mtdcr (maltxctp0r, hw_p->tx_phys); + mtdcr (malrxctp0r, hw_p->rx_phys); /* set RX buffer size */ mtdcr (malrcbs0, ENET_MAX_MTU_ALIGNED / 16); break; @@ -1083,6 +1066,7 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, /* memcpy ((void *) &tx_buff[tx_slot], (const void *) ptr, len); */ memcpy ((void *) hw_p->txbuf_ptr, (const void *) ptr, len); + flush_dcache_range((u32)hw_p->txbuf_ptr, (u32)hw_p->txbuf_ptr + len); /*-----------------------------------------------------------------------+ * set TX Buffer busy, and send it @@ -1582,6 +1566,9 @@ static int ppc_4xx_eth_rx (struct eth_device *dev) /* Pass the packet up to the protocol layers. */ /* NetReceive(NetRxPackets[rxIdx], length - 4); */ /* NetReceive(NetRxPackets[i], length); */ + invalidate_dcache_range((u32)hw_p->rx[user_index].data_ptr, + (u32)hw_p->rx[user_index].data_ptr + + length - 4); NetReceive (NetRxPackets[user_index], length - 4); /* Free Recv Buffer */ hw_p->rx[user_index].ctrl |= MAL_RX_CTRL_EMPTY; diff --git a/include/ppc4xx_enet.h b/include/ppc4xx_enet.h index 76c1d127efb..f2855007391 100644 --- a/include/ppc4xx_enet.h +++ b/include/ppc4xx_enet.h @@ -102,6 +102,8 @@ typedef struct emac_4xx_hw_st { uint32_t emac_ier; volatile mal_desc_t *tx; volatile mal_desc_t *rx; + u32 tx_phys; + u32 rx_phys; bd_t *bis; /* for eth_init upon mal error */ mal_desc_t *alloc_tx_buf; mal_desc_t *alloc_rx_buf; -- cgit v1.3.1 From 3d6cb3b24add6415f86a0f013ea40f5639b90047 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 3 Nov 2007 12:08:28 +0100 Subject: ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: Stefan Roese --- MAKEALL | 2 + Makefile | 9 +++ board/amcc/kilauea/config.mk | 10 ++- board/amcc/kilauea/init.S | 2 + board/amcc/kilauea/u-boot-nand.lds | 137 +++++++++++++++++++++++++++++++++ include/configs/kilauea.h | 88 ++++++++++++++++++--- nand_spl/board/amcc/kilauea/Makefile | 108 ++++++++++++++++++++++++++ nand_spl/board/amcc/kilauea/config.mk | 47 +++++++++++ nand_spl/board/amcc/kilauea/u-boot.lds | 64 +++++++++++++++ 9 files changed, 457 insertions(+), 10 deletions(-) create mode 100644 board/amcc/kilauea/u-boot-nand.lds create mode 100644 nand_spl/board/amcc/kilauea/Makefile create mode 100644 nand_spl/board/amcc/kilauea/config.mk create mode 100644 nand_spl/board/amcc/kilauea/u-boot.lds (limited to 'include') diff --git a/MAKEALL b/MAKEALL index 67b39c319b5..ef181bac73d 100755 --- a/MAKEALL +++ b/MAKEALL @@ -181,6 +181,7 @@ LIST_4xx=" \ EXBITGEN \ G2000 \ haleakala \ + haleakala_nand \ hcu4 \ hcu5 \ HH405 \ @@ -189,6 +190,7 @@ LIST_4xx=" \ KAREF \ katmai \ kilauea \ + kilauea_nand \ luan \ lwmon5 \ makalu \ diff --git a/Makefile b/Makefile index 814bba8af72..35f8d31095d 100644 --- a/Makefile +++ b/Makefile @@ -1173,6 +1173,15 @@ kilauea_config \ haleakala_config: unconfig @$(MKCONFIG) -n $@ -a kilauea ppc ppc4xx kilauea amcc +kilauea_nand_config \ +haleakala_nand_config: unconfig + @mkdir -p $(obj)include $(obj)board/amcc/kilauea + @mkdir -p $(obj)nand_spl/board/amcc/kilauea + @echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h + @$(MKCONFIG) -n $@ -a kilauea ppc ppc4xx kilauea amcc + @echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/kilauea/config.tmp + @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk + luan_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx luan amcc diff --git a/board/amcc/kilauea/config.mk b/board/amcc/kilauea/config.mk index a46b1972492..f5800ebe826 100644 --- a/board/amcc/kilauea/config.mk +++ b/board/amcc/kilauea/config.mk @@ -1,5 +1,5 @@ # -# (C) Copyright 2000 +# (C) Copyright 2007 # Wolfgang Denk, DENX Software Engineering, wd@denx.de. # # See file CREDITS for list of people who contributed to this @@ -21,4 +21,12 @@ # MA 02111-1307 USA # +sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp + +ifndef TEXT_BASE TEXT_BASE = 0xFFFA0000 +endif + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif diff --git a/board/amcc/kilauea/init.S b/board/amcc/kilauea/init.S index 96358c66514..43387445b14 100644 --- a/board/amcc/kilauea/init.S +++ b/board/amcc/kilauea/init.S @@ -38,6 +38,7 @@ .globl ext_bus_cntlr_init ext_bus_cntlr_init: +#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) /* * DDR2 setup @@ -148,5 +149,6 @@ pll_wait: /* Enable memory controller */ mtsdram_as(SDRAM_MCOPT2, 0x28000000); +#endif /* #ifndef CONFIG_NAND_U_BOOT */ blr diff --git a/board/amcc/kilauea/u-boot-nand.lds b/board/amcc/kilauea/u-boot-nand.lds new file mode 100644 index 00000000000..a5dae0e98cc --- /dev/null +++ b/board/amcc/kilauea/u-boot-nand.lds @@ -0,0 +1,137 @@ +/* + * (C) Copyright 2007 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/ppc4xx/start.o (.text) + + /* Align to next NAND block */ + . = ALIGN(0x4000); + common/environment.o (.ppcenv) + /* Keep some space here for redundant env and potential bad env blocks */ + . = ALIGN(0x10000); + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index caf8b5287a5..07f7eff39e5 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -50,7 +50,7 @@ #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ #define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- @@ -117,6 +117,71 @@ #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ + +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + +#ifdef CFG_ENV_IS_IN_NAND +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/sequoia/u-boot-nand.lds for details. + */ +#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ @@ -332,6 +397,18 @@ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ +#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) +/* booting from NAND, so NAND chips select has to be on CS 0 */ +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ + +/* Memory Bank 1 (NOR-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x05806500 +#define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ + +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000) +#else #define CFG_NAND_CS 1 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ @@ -341,6 +418,7 @@ /* Memory Bank 1 (NAND-FLASH) initialization */ #define CFG_EBC_PB1AP 0x018003c0 #define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000) +#endif /* Memory Bank 2 (FPGA) initialization */ #define CFG_EBC_PB2AP 0x9400C800 @@ -348,14 +426,6 @@ #define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ -/*----------------------------------------------------------------------- - * NAND FLASH - *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ - /*----------------------------------------------------------------------- * GPIO Setup *----------------------------------------------------------------------*/ diff --git a/nand_spl/board/amcc/kilauea/Makefile b/nand_spl/board/amcc/kilauea/Makefile new file mode 100644 index 00000000000..98f27750036 --- /dev/null +++ b/nand_spl/board/amcc/kilauea/Makefile @@ -0,0 +1,108 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk + +LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds +LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS) +AFLAGS += -DCONFIG_NAND_SPL +CFLAGS += -DCONFIG_NAND_SPL + +SOBJS = start.o init.o resetvec.o cache.o +COBJS = memory.o nand_boot.o nand_ecc.o ndfc.o + +SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) +OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) +__OBJS := $(SOBJS) $(COBJS) +LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR) + +nandobj := $(OBJTREE)/nand_spl/ + +ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin + +all: $(obj).depend $(ALL) + +$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@ + +$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl + $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@ + +$(nandobj)u-boot-spl: $(OBJS) + cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \ + -Map $(nandobj)u-boot-spl.map \ + -o $(nandobj)u-boot-spl + +# create symbolic links for common files + +# from cpu directory +$(obj)cache.S: + @rm -f $(obj)cache.S + ln -s $(SRCTREE)/cpu/ppc4xx/cache.S $(obj)cache.S + +$(obj)ndfc.c: + @rm -f $(obj)ndfc.c + ln -s $(SRCTREE)/cpu/ppc4xx/ndfc.c $(obj)ndfc.c + +$(obj)resetvec.S: + @rm -f $(obj)resetvec.S + ln -s $(SRCTREE)/cpu/ppc4xx/resetvec.S $(obj)resetvec.S + +$(obj)start.S: + @rm -f $(obj)start.S + ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S + +# from board directory +$(obj)init.S: + @rm -f $(obj)init.S + ln -s $(SRCTREE)/board/amcc/kilauea/init.S $(obj)init.S + +$(obj)memory.c: + @rm -f $(obj)memory.c + ln -s $(SRCTREE)/board/amcc/kilauea/memory.c $(obj)memory.c + +# from nand_spl directory +$(obj)nand_boot.c: + @rm -f $(obj)nand_boot.c + ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c + +# from drivers/nand directory +$(obj)nand_ecc.c: + @rm -f $(obj)nand_ecc.c + ln -s $(SRCTREE)/drivers/nand/nand_ecc.c $(obj)nand_ecc.c + +######################################################################### + +$(obj)%.o: $(obj)%.S + $(CC) $(AFLAGS) -c -o $@ $< + +$(obj)%.o: $(obj)%.c + $(CC) $(CFLAGS) -c -o $@ $< + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/nand_spl/board/amcc/kilauea/config.mk b/nand_spl/board/amcc/kilauea/config.mk new file mode 100644 index 00000000000..22490918d07 --- /dev/null +++ b/nand_spl/board/amcc/kilauea/config.mk @@ -0,0 +1,47 @@ +# +# (C) Copyright 2007 +# Stefan Roese, DENX Software Engineering, sr@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# +# +# AMCC 405EX Reference Platform (Kilauea) board +# + +# +# TEXT_BASE for SPL: +# +# On 4xx platforms the SPL is located at 0xfffff000...0xffffffff, +# in the last 4kBytes of memory space in cache. +# We will copy this SPL into instruction-cache in start.S. So we set +# TEXT_BASE to starting address in i-cache here. +# +TEXT_BASE = 0x00800000 + +# PAD_TO used to generate a 16kByte binary needed for the combined image +# -> PAD_TO = TEXT_BASE + 0x4000 +PAD_TO = 0x00804000 + +ifeq ($(debug),1) +PLATFORM_CPPFLAGS += -DDEBUG +endif + +ifeq ($(dbcr),1) +PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 +endif diff --git a/nand_spl/board/amcc/kilauea/u-boot.lds b/nand_spl/board/amcc/kilauea/u-boot.lds new file mode 100644 index 00000000000..24df32d02ee --- /dev/null +++ b/nand_spl/board/amcc/kilauea/u-boot.lds @@ -0,0 +1,64 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc:common) +SECTIONS +{ + .resetvec 0x00800FFC : + { + *(.resetvec) + } = 0xffff + + .text : + { + start.o (.text) + init.o (.text) + nand_boot.o (.text) + ndfc.o (.text) + + *(.text) + *(.fixup) + } + _etext = .; + + .data : + { + *(.rodata*) + *(.data*) + *(.sdata*) + __got2_start = .; + *(.got2) + __got2_end = .; + } + + _edata = .; + + __bss_start = .; + .bss : + { + *(.sbss) + *(.bss) + } + + _end = . ; +} -- cgit v1.3.1 From 9f23ca334a6f5f021ef9e9d0fad9da80d63b2d56 Mon Sep 17 00:00:00 2001 From: Jason Jin Date: Mon, 29 Oct 2007 19:26:21 +0800 Subject: Unify pixis_reset altbank across board families Basically, refactor the CFG_PIXIS_VBOOT_MASK values into the separate board config files. Signed-off-by: Jason Jin Signed-off-by: Jon Loeliger --- board/freescale/common/pixis.c | 5 ++++- include/configs/MPC8544DS.h | 1 + include/configs/MPC8641HPCN.h | 1 + 3 files changed, 6 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c index fd99a938c0f..45dcf4dab03 100644 --- a/board/freescale/common/pixis.c +++ b/board/freescale/common/pixis.c @@ -207,13 +207,16 @@ void read_from_px_regs_altbank(int set) out8(PIXIS_BASE + PIXIS_VCFGEN1, tmp); } +#ifndef CFG_PIXIS_VBOOT_MASK +#define CFG_PIXIS_VBOOT_MASK 0x40 +#endif void set_altbank(void) { u8 tmp; tmp = in8(PIXIS_BASE + PIXIS_VBOOT); - tmp ^= 0x40; + tmp ^= CFG_PIXIS_VBOOT_MASK; out8(PIXIS_BASE + PIXIS_VBOOT, tmp); } diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index f580ccadee5..13e2a2c079f 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -198,6 +198,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ /* define to use L1 as initial stack */ diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index aa6dbc47adf..6f872402633 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -201,6 +201,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ -- cgit v1.3.1 From f3bceaab230b4748d0afc4109b6837308f018b40 Mon Sep 17 00:00:00 2001 From: Jason Jin Date: Fri, 26 Oct 2007 18:31:59 +0800 Subject: Fix the BAT definition of PCI IO on 8610 board The address in the BAT register is aligned with the BAT size. The original definition actually did not define BAT for PCIE2 IO. This patch fix this. Signed-off-by: Jason Jin --- include/configs/MPC8610HPCD.h | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index be3434a4c9b..8bbe447a63c 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -361,28 +361,26 @@ #define CFG_IBAT1U CFG_DBAT1U /* - * BAT2 32M Cache-inhibited, guarded + * BAT2 16M Cache-inhibited, guarded * 0xe100_0000 1M PCI-1 I/O - * 0xe200_0000 1M PCI-Express 2 I/O - * */ #define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP) #define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT2U CFG_DBAT2U /* - * BAT3 1M Cache-inhibited, guarded + * BAT3 32M Cache-inhibited, guarded + * 0xe200_0000 1M PCI-Express 2 I/O * 0xe300_0000 1M PCI-Express 1 I/O - * */ -#define CFG_DBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ +#define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ | BATL_GUARDEDSTORAGE) -#define CFG_DBAT3U (CFG_PCIE1_IO_PHYS | BATU_BL_1M | BATU_VS | BATU_VP) -#define CFG_IBAT3L (CFG_PCIE1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) #define CFG_IBAT3U CFG_DBAT3U /* -- cgit v1.3.1 From 761421ccca80a9fb37b19c37aa61d46ef75e0647 Mon Sep 17 00:00:00 2001 From: Jason Jin Date: Mon, 29 Oct 2007 19:26:21 +0800 Subject: 8610: Actually enable pixis_reset CONFIGs Signed-off-by: Jason Jin --- include/configs/MPC8610HPCD.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 8bbe447a63c..8b6b117f30b 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -151,6 +151,7 @@ #define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ +#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ #define PIXIS_BASE 0xe8000000 /* PIXIS registers */ #define PIXIS_ID 0x0 /* Board ID at offset 0 */ #define PIXIS_VER 0x1 /* Board version at offset 1 */ @@ -166,6 +167,7 @@ #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ +#define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/ #define CFG_MAX_FLASH_BANKS 2 /* number of banks */ #define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ -- cgit v1.3.1 From 1815338fbd1c0f94f8276d2891b99caa5a05f622 Mon Sep 17 00:00:00 2001 From: York Sun Date: Mon, 29 Oct 2007 13:57:53 -0500 Subject: 8610: Make some extra debug environment variables conditional. One may #define ENV_DEBUG to get them back again. Signed-off-by: York Sun --- include/configs/MPC8610HPCD.h | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 8b6b117f30b..9fa42f32daa 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -587,7 +587,7 @@ "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\ "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0" - +#ifdef ENV_DEBUG #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ @@ -632,6 +632,17 @@ PCI_ENV \ PCIE_ENV \ DMA_ENV +#else +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ + "dtbaddr=c00000\0" \ + "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \ + "bdev=sda3\0" +#endif #define CONFIG_NFSBOOTCOMMAND \ "setenv bootargs root=/dev/nfs rw " \ -- cgit v1.3.1 From a877880c6949e948bd63cd6ea4e216573d2f53dd Mon Sep 17 00:00:00 2001 From: York Sun Date: Mon, 29 Oct 2007 13:58:39 -0500 Subject: 8610: Add 8610 DIU display driver 1280x1024 and 1024x768 @ 32 bpp are supported now. DVI, Single-link LVDS, Double-link LVDS are all supported. Environmental variable "monitor" is used to specify monitor port. A new command "diufb" is introduced to reinitialize monitor and display a BMP file in the memory. So far, 1-bit, 4-bit, 8-bit and 24-bit BMP formats are supported. diufb init - initialize the diu driver Enable the port specified in the environmental variable "monitor" diufb addr - display bmp file in memory. The bmp image should be no bigger than the resolution, 1280x1024 for DVI and double-link LVDS, 1024x768 for single-link LVDS. Note, this driver allocate memory but doesn't free it after use It is written on purpose -- to avoid a failure of reallocation due to memory fragement. ECC of DDR is disabled for DIU performance. L2 data cache is also disabled. Signed-off-by: York Sun Signed-off-by: Jon loeliger --- board/freescale/common/Makefile | 4 +- board/freescale/common/fsl_diu_fb.c | 656 ++++++++++++++++++++++++++ board/freescale/common/fsl_diu_fb.h | 35 ++ board/freescale/mpc8610hpcd/Makefile | 4 +- board/freescale/mpc8610hpcd/mpc8610hpcd.c | 45 +- board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c | 105 +++++ include/configs/MPC8610HPCD.h | 19 +- 7 files changed, 858 insertions(+), 10 deletions(-) create mode 100644 board/freescale/common/fsl_diu_fb.c create mode 100644 board/freescale/common/fsl_diu_fb.h create mode 100644 board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c (limited to 'include') diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 44f613e4185..9cee9f19bb5 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -31,7 +31,9 @@ LIB = $(obj)lib$(VENDOR).a COBJS := sys_eeprom.o \ pixis.o \ - pq-mds-pib.o + pq-mds-pib.o \ + fsl_logo_bmp.o \ + fsl_diu_fb.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/freescale/common/fsl_diu_fb.c b/board/freescale/common/fsl_diu_fb.c new file mode 100644 index 00000000000..a9999d393fa --- /dev/null +++ b/board/freescale/common/fsl_diu_fb.c @@ -0,0 +1,656 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * York Sun + * + * FSL DIU Framebuffer driver + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#include +#include +#include + +#ifdef CONFIG_FSL_DIU_FB + +#include "fsl_diu_fb.h" + + +#ifdef DEBUG +#define DPRINTF(fmt, args...) printf("%s: " fmt,__FUNCTION__,## args) +#else +#define DPRINTF(fmt, args...) +#endif + +struct fb_var_screeninfo { + unsigned int xres; /* visible resolution */ + unsigned int yres; + + unsigned int bits_per_pixel; /* guess what */ + + /* Timing: All values in pixclocks, except pixclock (of course) */ + unsigned int pixclock; /* pixel clock in ps (pico seconds) */ + unsigned int left_margin; /* time from sync to picture */ + unsigned int right_margin; /* time from picture to sync */ + unsigned int upper_margin; /* time from sync to picture */ + unsigned int lower_margin; + unsigned int hsync_len; /* length of horizontal sync */ + unsigned int vsync_len; /* length of vertical sync */ + unsigned int sync; /* see FB_SYNC_* */ + unsigned int vmode; /* see FB_VMODE_* */ + unsigned int rotate; /* angle we rotate counter clockwise */ +}; + +struct fb_info { + struct fb_var_screeninfo var; /* Current var */ + unsigned long smem_start; /* Start of frame buffer mem */ + /* (physical address) */ + unsigned int smem_len; /* Length of frame buffer mem */ + unsigned int type; /* see FB_TYPE_* */ + unsigned int line_length; /* length of a line in bytes */ + + char *screen_base; + unsigned long screen_size; + int logo_height; + unsigned int logo_size; +}; + +struct fb_videomode { + const char *name; /* optional */ + unsigned int refresh; /* optional */ + unsigned int xres; + unsigned int yres; + unsigned int pixclock; + unsigned int left_margin; + unsigned int right_margin; + unsigned int upper_margin; + unsigned int lower_margin; + unsigned int hsync_len; + unsigned int vsync_len; + unsigned int sync; + unsigned int vmode; + unsigned int flag; +}; + +#define FB_SYNC_VERT_HIGH_ACT 2 /* vertical sync high active */ +#define FB_SYNC_COMP_HIGH_ACT 8 /* composite sync high active */ +#define FB_VMODE_NONINTERLACED 0 /* non interlaced */ + +/* + * These parameters give default parameters + * for video output 1024x768, + * FIXME - change timing to proper amounts + * hsync 31.5kHz, vsync 60Hz + */ +static struct fb_videomode fsl_diu_mode_1024 = { + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 160, + .right_margin = 24, + .upper_margin = 29, + .lower_margin = 3, + .hsync_len = 136, + .vsync_len = 6, + .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .vmode = FB_VMODE_NONINTERLACED +}; + +static struct fb_videomode fsl_diu_mode_1280 = { + .name = "1280x1024-60", + .refresh = 60, + .xres = 1280, + .yres = 1024, + .pixclock = 9375, + .left_margin = 38, + .right_margin = 128, + .upper_margin = 2, + .lower_margin = 7, + .hsync_len = 216, + .vsync_len = 37, + .sync = FB_SYNC_COMP_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .vmode = FB_VMODE_NONINTERLACED +}; + +/* + * These are the fields of area descriptor(in DDR memory) for every plane + */ +struct diu_ad { + /* Word 0(32-bit) in DDR memory */ + unsigned int pix_fmt; /* hard coding pixel format */ + /* Word 1(32-bit) in DDR memory */ + unsigned int addr; + /* Word 2(32-bit) in DDR memory */ + unsigned int src_size_g_alpha; + /* Word 3(32-bit) in DDR memory */ + unsigned int aoi_size; + /* Word 4(32-bit) in DDR memory */ + unsigned int offset_xyi; + /* Word 5(32-bit) in DDR memory */ + unsigned int offset_xyd; + /* Word 6(32-bit) in DDR memory */ + unsigned int ckmax_r:8; + unsigned int ckmax_g:8; + unsigned int ckmax_b:8; + unsigned int res9:8; + /* Word 7(32-bit) in DDR memory */ + unsigned int ckmin_r:8; + unsigned int ckmin_g:8; + unsigned int ckmin_b:8; + unsigned int res10:8; + /* Word 8(32-bit) in DDR memory */ + unsigned int next_ad; + /* Word 9(32-bit) in DDR memory, just for 64-bit aligned */ + unsigned int res1; + unsigned int res2; + unsigned int res3; +}__attribute__ ((packed)); + +/* + * DIU register map + */ +struct diu { + unsigned int desc[3]; + unsigned int gamma; + unsigned int pallete; + unsigned int cursor; + unsigned int curs_pos; + unsigned int diu_mode; + unsigned int bgnd; + unsigned int bgnd_wb; + unsigned int disp_size; + unsigned int wb_size; + unsigned int wb_mem_addr; + unsigned int hsyn_para; + unsigned int vsyn_para; + unsigned int syn_pol; + unsigned int thresholds; + unsigned int int_status; + unsigned int int_mask; + unsigned int colorbar[8]; + unsigned int filling; + unsigned int plut; +} __attribute__ ((packed)); + +struct diu_hw { + struct diu *diu_reg; + volatile unsigned int mode; /* DIU operation mode */ +}; + +struct diu_addr { + unsigned char * paddr; /* Virtual address */ + unsigned int offset; +}; + +#define FSL_DIU_BASE_OFFSET 0x2C000 /* Offset of Display Interface Unit */ + +/* + * Modes of operation of DIU + */ +#define MFB_MODE0 0 /* DIU off */ +#define MFB_MODE1 1 /* All three planes output to display */ +#define MFB_MODE2 2 /* Plane 1 to display, + * planes 2+3 written back to memory */ +#define MFB_MODE3 3 /* All three planes written back to memory */ +#define MFB_MODE4 4 /* Color bar generation */ + +#define MAX_CURS 32 + + + +static struct fb_info fsl_fb_info; +static struct diu_addr gamma, cursor; +static struct diu_ad fsl_diu_fb_ad __attribute__ ((aligned(32))); +static struct diu_ad dummy_ad __attribute__ ((aligned(32))); +static unsigned char *dummy_fb; +static struct diu_hw dr = { + .mode = MFB_MODE1, +}; + +int fb_enabled = 0; +int fb_initialized = 0; +const int default_xres = 1280; +const int default_pixel_format = 0x88882317; + +static int map_video_memory(struct fb_info *info, unsigned long bytes_align); +static void enable_lcdc(void); +static void disable_lcdc(void); +static int fsl_diu_enable_panel(struct fb_info *info); +static int fsl_diu_disable_panel(struct fb_info *info); +static int allocate_buf(struct diu_addr *buf, u32 size, u32 bytes_align); +static u32 get_busfreq(void); + + +int fsl_diu_init(int xres, + unsigned int pixel_format, + int gamma_fix, + unsigned char *splash_bmp) +{ + struct fb_videomode *fsl_diu_mode_db; + struct diu_ad *ad = &fsl_diu_fb_ad; + struct diu *hw; + struct fb_info *info = &fsl_fb_info; + struct fb_var_screeninfo *var = &info->var; + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_gur_t *gur = &immap->im_gur; + volatile unsigned int *guts_clkdvdr = &gur->clkdvdr; + unsigned char *gamma_table_base; + unsigned int i, j; + unsigned long speed_ccb, temp, pixval; + + DPRINTF("Enter fsl_diu_init\n"); + dr.diu_reg = (struct diu *) (CFG_IMMR + FSL_DIU_BASE_OFFSET); + hw = (struct diu *) dr.diu_reg; + + disable_lcdc(); + + if (xres == 1280) { + fsl_diu_mode_db = &fsl_diu_mode_1280; + } else { + fsl_diu_mode_db = &fsl_diu_mode_1024; + } + + if (0 == fb_initialized) { + allocate_buf(&gamma, 768, 32); + DPRINTF("gamma is allocated @ 0x%x\n", + (unsigned int)gamma.paddr); + allocate_buf(&cursor, MAX_CURS * MAX_CURS * 2, 32); + DPRINTF("curosr is allocated @ 0x%x\n", + (unsigned int)cursor.paddr); + + /* create a dummy fb and dummy ad */ + dummy_fb = malloc(64); + if (NULL == dummy_fb) { + printf("Cannot allocate dummy fb\n"); + return -1; + } + dummy_ad.addr = cpu_to_le32((unsigned int)dummy_fb); + dummy_ad.pix_fmt = 0x88882317; + dummy_ad.src_size_g_alpha = 0x04400000; /* alpha = 0 */ + dummy_ad.aoi_size = 0x02000400; + dummy_ad.offset_xyi = 0; + dummy_ad.offset_xyd = 0; + dummy_ad.next_ad = 0; + /* Memory allocation for framebuffer */ + if (map_video_memory(info, 32)) { + printf("Unable to allocate fb memory 1\n"); + return -1; + } + } else { + memset(info->screen_base, 0, info->smem_len); + } + + dr.diu_reg->desc[0] = (unsigned int) &dummy_ad; + dr.diu_reg->desc[1] = (unsigned int) &dummy_ad; + dr.diu_reg->desc[2] = (unsigned int) &dummy_ad; + DPRINTF("dummy dr.diu_reg->desc[0] = 0x%x\n", dr.diu_reg->desc[0]); + DPRINTF("dummy desc[0] = 0x%x\n", hw->desc[0]); + + /* read mode info */ + var->xres = fsl_diu_mode_db->xres; + var->yres = fsl_diu_mode_db->yres; + var->bits_per_pixel = 32; + var->pixclock = fsl_diu_mode_db->pixclock; + var->left_margin = fsl_diu_mode_db->left_margin; + var->right_margin = fsl_diu_mode_db->right_margin; + var->upper_margin = fsl_diu_mode_db->upper_margin; + var->lower_margin = fsl_diu_mode_db->lower_margin; + var->hsync_len = fsl_diu_mode_db->hsync_len; + var->vsync_len = fsl_diu_mode_db->vsync_len; + var->sync = fsl_diu_mode_db->sync; + var->vmode = fsl_diu_mode_db->vmode; + info->line_length = var->xres * var->bits_per_pixel / 8; + info->logo_size = 0; + info->logo_height = 0; + + ad->pix_fmt = pixel_format; + ad->addr = cpu_to_le32((unsigned int)info->screen_base); + ad->src_size_g_alpha + = cpu_to_le32((var->yres << 12) | var->xres); + /* fix me. AOI should not be greater than display size */ + ad->aoi_size = cpu_to_le32(( var->yres << 16) | var->xres); + ad->offset_xyi = 0; + ad->offset_xyd = 0; + + /* Disable chroma keying function */ + ad->ckmax_r = 0; + ad->ckmax_g = 0; + ad->ckmax_b = 0; + + ad->ckmin_r = 255; + ad->ckmin_g = 255; + ad->ckmin_b = 255; + + gamma_table_base = gamma.paddr; + DPRINTF("gamma_table_base is allocated @ 0x%x\n", + (unsigned int)gamma_table_base); + + /* Prep for DIU init - gamma table */ + + for (i = 0; i <= 2; i++) + for (j = 0; j <= 255; j++) + *gamma_table_base++ = j; + + if (gamma_fix == 1) { /* fix the gamma */ + DPRINTF("Fix gamma table\n"); + gamma_table_base = gamma.paddr; + for (i = 0; i < 256*3; i++) { + gamma_table_base[i] = (gamma_table_base[i] << 2) + | ((gamma_table_base[i] >> 6) & 0x03); + } + } + + DPRINTF("update-lcdc: HW - %p\n Disabling DIU\n", hw); + + /* Program DIU registers */ + + hw->gamma = (unsigned int) gamma.paddr; + hw->cursor= (unsigned int) cursor.paddr; + hw->bgnd = 0x007F7F7F; /* BGND */ + hw->bgnd_wb = 0; /* BGND_WB */ + hw->disp_size = var->yres << 16 | var->xres; /* DISP SIZE */ + hw->wb_size = 0; /* WB SIZE */ + hw->wb_mem_addr = 0; /* WB MEM ADDR */ + hw->hsyn_para = var->left_margin << 22 | /* BP_H */ + var->hsync_len << 11 | /* PW_H */ + var->right_margin; /* FP_H */ + hw->vsyn_para = var->upper_margin << 22 | /* BP_V */ + var->vsync_len << 11 | /* PW_V */ + var->lower_margin; /* FP_V */ + + /* Pixel Clock configuration */ + DPRINTF("DIU: Bus Frequency = %d\n", get_busfreq()); + speed_ccb = get_busfreq(); + + DPRINTF("DIU pixclock in ps - %d\n", var->pixclock); + temp = 1; + temp *= 1000000000; + temp /= var->pixclock; + temp *= 1000; + pixval = speed_ccb / temp; + DPRINTF("DIU pixval = %lu\n", pixval); + + hw->syn_pol = 0; /* SYNC SIGNALS POLARITY */ + hw->thresholds = 0x00037800; /* The Thresholds */ + hw->int_status = 0; /* INTERRUPT STATUS */ + hw->int_mask = 0; /* INT MASK */ + hw->plut = 0x01F5F666; + + /* Modify PXCLK in GUTS CLKDVDR */ + DPRINTF("DIU: Current value of CLKDVDR = 0x%08x\n", *guts_clkdvdr); + temp = *guts_clkdvdr & 0x2000FFFF; + *guts_clkdvdr = temp; /* turn off clock */ + *guts_clkdvdr = temp | 0x80000000 | ((pixval & 0x1F) << 16); + DPRINTF("DIU: Modified value of CLKDVDR = 0x%08x\n", *guts_clkdvdr); + + fb_initialized = 1; + + if (splash_bmp) { + info->logo_height = fsl_diu_display_bmp(splash_bmp, 0, 0, 0); + info->logo_size = info->logo_height * info->line_length; + DPRINTF("logo height %d, logo_size 0x%x\n", + info->logo_height,info->logo_size); + } + + /* Enable the DIU */ + fsl_diu_enable_panel(info); + enable_lcdc(); + + return 0; +} + +char *fsl_fb_open(struct fb_info **info) +{ + *info = &fsl_fb_info; + return (char *) ((unsigned int)(*info)->screen_base + + (*info)->logo_size); +} + +void fsl_diu_close(void) +{ + struct fb_info *info = &fsl_fb_info; + fsl_diu_disable_panel(info); +} + +static int fsl_diu_enable_panel(struct fb_info *info) +{ + struct diu *hw = dr.diu_reg; + struct diu_ad *ad = &fsl_diu_fb_ad; + + DPRINTF("Entered: enable_panel\n"); + if (hw->desc[0] != (unsigned int)ad) + hw->desc[0] = (unsigned int)ad; + DPRINTF("desc[0] = 0x%x\n", hw->desc[0]); + return 0; +} + +static int fsl_diu_disable_panel(struct fb_info *info) +{ + struct diu *hw = dr.diu_reg; + + DPRINTF("Entered: disable_panel\n"); + if (hw->desc[0] != (unsigned int)&dummy_ad) + hw->desc[0] = (unsigned int)&dummy_ad; + return 0; +} + +static int map_video_memory(struct fb_info *info, unsigned long bytes_align) +{ + unsigned long offset; + unsigned long mask; + + DPRINTF("Entered: map_video_memory\n"); + /* allocate maximum 1280*1024 with 32bpp */ + info->smem_len = 1280 * 4 *1024 + bytes_align; + DPRINTF("MAP_VIDEO_MEMORY: smem_len = %d\n", info->smem_len); + info->screen_base = malloc(info->smem_len); + if (info->screen_base == NULL) { + printf("Unable to allocate fb memory\n"); + return -1; + } + info->smem_start = (unsigned int) info->screen_base; + mask = bytes_align - 1; + offset = (unsigned long)info->screen_base & mask; + if (offset) { + info->screen_base += offset; + info->smem_len = info->smem_len - (bytes_align - offset); + } else + info->smem_len = info->smem_len - bytes_align; + + info->screen_size = info->smem_len; + + DPRINTF("Allocated fb @ 0x%08lx, size=%d.\n", + info->smem_start, info->smem_len); + + return 0; +} + +static void enable_lcdc(void) +{ + struct diu *hw = dr.diu_reg; + + DPRINTF("Entered: enable_lcdc, fb_enabled = %d\n", fb_enabled); + if (!fb_enabled) { + hw->diu_mode = dr.mode; + fb_enabled++; + } + DPRINTF("diu_mode = %d\n", hw->diu_mode); +} + +static void disable_lcdc(void) +{ + struct diu *hw = dr.diu_reg; + + DPRINTF("Entered: disable_lcdc, fb_enabled = %d\n", fb_enabled); + if (fb_enabled) { + hw->diu_mode = 0; + fb_enabled = 0; + } +} + +static u32 get_busfreq(void) +{ + u32 fs_busfreq = 0; + + fs_busfreq = get_bus_freq(0); + return fs_busfreq; +} + +/* + * Align to 64-bit(8-byte), 32-byte, etc. + */ +static int allocate_buf(struct diu_addr *buf, u32 size, u32 bytes_align) +{ + u32 offset, ssize; + u32 mask; + + DPRINTF("Entered: allocate_buf\n"); + ssize = size + bytes_align; + buf->paddr = malloc(ssize); + if (!buf->paddr) + return -1; + + memset(buf->paddr, 0, ssize); + mask = bytes_align - 1; + offset = (u32)buf->paddr & mask; + if (offset) { + buf->offset = bytes_align - offset; + buf->paddr = (unsigned char *) ((u32)buf->paddr + offset); + } else + buf->offset = 0; + return 0; +} + +int fsl_diu_display_bmp(unsigned char *bmp, + int xoffset, + int yoffset, + int transpar) +{ + struct fb_info *info = &fsl_fb_info; + unsigned char r, g, b; + unsigned int *fb_t, val; + unsigned char *bitmap; + unsigned int palette[256]; + int width, height, bpp, ncolors, raster, offset, x, y, i, k, cpp; + + if (!bmp) { + printf("Must supply a bitmap address\n"); + return 0; + } + + raster = bmp[10] + (bmp[11] << 8) + (bmp[12] << 16) + (bmp[13] << 24); + width = (bmp[21] << 24) | (bmp[20] << 16) | (bmp[19] << 8) | bmp[18]; + height = (bmp[25] << 24) | (bmp[24] << 16) | (bmp[23] << 8) | bmp[22]; + bpp = (bmp[29] << 8) | (bmp[28]); + ncolors = bmp[46] + (bmp[47] << 8) + (bmp[48] << 16) + (bmp[49] << 24); + bitmap = bmp + raster; + cpp = info->var.bits_per_pixel / 8; + + DPRINTF("bmp = 0x%08x\n", (unsigned int)bmp); + DPRINTF("bitmap = 0x%08x\n", (unsigned int)bitmap); + DPRINTF("width = %d\n", width); + DPRINTF("height = %d\n", height); + DPRINTF("bpp = %d\n", bpp); + DPRINTF("ncolors = %d\n", ncolors); + + DPRINTF("xres = %d\n", info->var.xres); + DPRINTF("yres = %d\n", info->var.yres); + DPRINTF("Screen_base = 0x%x\n", (unsigned int)info->screen_base); + + if (((width+xoffset) > info->var.xres) || + ((height+yoffset) > info->var.yres)) { + printf("bitmap is out of range, image too large or too much offset\n"); + return 0; + } + if (bpp < 24) { + for (i = 0, offset = 54; i < ncolors; i++, offset += 4) + palette[i] = (bmp[offset+2] << 16) + + (bmp[offset+1] << 8) + bmp[offset]; + } + + switch (bpp) { + case 1: + for (y = height - 1; y >= 0; y--) { + fb_t = (unsigned int *) ((unsigned int)info->screen_base + (((y+yoffset) * info->var.xres) + xoffset)*cpp); + for (x = 0; x < width; x += 8) { + b = *bitmap++; + for (k = 0; k < 8; k++) { + if (b & 0x80) + *fb_t = palette[1]; + else + *fb_t = palette[0]; + b = b << 1; + } + } + for (i = (width / 2) % 4; i > 0; i--) + bitmap++; + } + break; + case 4: + for (y = height - 1; y >= 0; y--) { + fb_t = (unsigned int *) ((unsigned int)info->screen_base + (((y+yoffset) * info->var.xres) + xoffset)*cpp); + for (x = 0; x < width; x += 2) { + b = *bitmap++; + r = (b >> 4) & 0x0F; + g = b & 0x0F; + *fb_t++ = palette[r]; + *fb_t++ = palette[g]; + } + for (i = (width / 2) % 4; i > 0; i--) + bitmap++; + } + break; + case 8: + for (y = height - 1; y >= 0; y--) { + fb_t = (unsigned int *) ((unsigned int)info->screen_base + (((y+yoffset) * info->var.xres) + xoffset)*cpp); + for (x = 0; x < width; x++) { + *fb_t++ = palette[ *bitmap++ ]; + } + for (i = (width / 2) % 4; i > 0; i--) + bitmap++; + } + break; + case 24: + for (y = height - 1; y >= 0; y--) { + fb_t = (unsigned int *) ((unsigned int)info->screen_base + (((y+yoffset) * info->var.xres) + xoffset)*cpp); + for (x = 0; x < width; x++) { + b = *bitmap++; + g = *bitmap++; + r = *bitmap++; + val = (r << 16) + (g << 8) + b; + *fb_t++ = val; + } + for (; (x % 4) != 0; x++) /* 4-byte alignment */ + bitmap++; + } + break; + } + + return height; +} + +void fsl_diu_clear_screen(void) +{ + struct fb_info *info = &fsl_fb_info; + + memset(info->screen_base, 0, info->smem_len); +} +#endif /* CONFIG_FSL_DIU_FB */ diff --git a/board/freescale/common/fsl_diu_fb.h b/board/freescale/common/fsl_diu_fb.h new file mode 100644 index 00000000000..9ddd4c0a58c --- /dev/null +++ b/board/freescale/common/fsl_diu_fb.h @@ -0,0 +1,35 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * York Sun + * + * FSL DIU Framebuffer driver + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +extern int fsl_diu_init(int xres, + unsigned int pixel_format, + int gamma_fix, + unsigned char *splash_bmp); +extern void fsl_diu_clear_screen(void); +extern int fsl_diu_display_bmp(unsigned char *bmp, + int xoffset, + int yoffset, + int transpar); diff --git a/board/freescale/mpc8610hpcd/Makefile b/board/freescale/mpc8610hpcd/Makefile index 6f5a5c16e3c..76087c12a6e 100644 --- a/board/freescale/mpc8610hpcd/Makefile +++ b/board/freescale/mpc8610hpcd/Makefile @@ -29,7 +29,9 @@ LIB = $(obj)lib$(BOARD).a COBJS := $(BOARD).o \ ../common/sys_eeprom.o \ - ../common/pixis.o + ../common/pixis.o \ + mpc8610hpcd_diu.o \ + ../common/fsl_diu_fb.o SOBJS := init.o diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index 63790ca9b64..617881ad094 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -54,7 +54,47 @@ int board_early_init_f(void) volatile immap_t *immap = (immap_t *)CFG_IMMR; volatile ccsr_gur_t *gur = &immap->im_gur; - gur->gpiocr |= 0x888a5500; /* DIU16, IR1, UART0, UART2 */ + gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */ + + return 0; +} + +int misc_init_r(void) +{ + u8 tmp_val, version; + + /*Do not use 8259PIC*/ + tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0); + out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x80); + + /*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/ + version = in8(PIXIS_BASE + PIXIS_PVER); + if(version >= 0x07) { + tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0); + out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val & 0xbf); + } + + /* Using this for DIU init before the driver in linux takes over + * Enable the TFP410 Encoder (I2C address 0x38) + */ + + tmp_val = 0xBF; + i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); + /* Verify if enabled */ + tmp_val = 0; + i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val)); + debug("DVI Encoder Read: 0x%02lx\n",tmp_val); + + tmp_val = 0x10; + i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); + /* Verify if enabled */ + tmp_val = 0; + i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val)); + debug("DVI Encoder Read: 0x%02lx\n",tmp_val); + +#ifdef CONFIG_FSL_DIU_FB + mpc8610hpcd_diu_init(); +#endif return 0; } @@ -62,7 +102,6 @@ int board_early_init_f(void) int checkboard(void) { volatile immap_t *immap = (immap_t *)CFG_IMMR; - volatile ccsr_lbc_t *memctl = &immap->im_lbc; volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm; puts("Board: MPC8610HPCD\n"); @@ -468,7 +507,7 @@ ft_board_setup(void *blob, bd_t *bd) unsigned long get_board_sys_clk(ulong dummy) { - u8 i, go_bit, rd_clks; + u8 i; ulong val = 0; ulong a; diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c new file mode 100644 index 00000000000..4449376789c --- /dev/null +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c @@ -0,0 +1,105 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * York Sun + * + * FSL DIU Framebuffer driver + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#ifdef CONFIG_FSL_DIU_FB + +#include "../common/pixis.h" +#include "../common/fsl_diu_fb.h" + + +extern unsigned int FSL_Logo_BMP[]; + + +void mpc8610hpcd_diu_init(void) +{ + char *monitor_port; + int xres, gamma_fix; + unsigned int pixel_format; + unsigned char tmp_val; + + tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0); + monitor_port = getenv ("monitor"); + + if (!strncmp(monitor_port, "0", 1)) { /* 0 - DVI */ + xres = 1280; + pixel_format = 0x88882317; + gamma_fix = 0; + out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x08); + + } else if (!strncmp(monitor_port, "1", 1)) { /* 1 - Single link LVDS */ + xres = 1024; + pixel_format = 0x88883316; + gamma_fix = 0; + out8(PIXIS_BASE + PIXIS_BRDCFG0, (tmp_val & 0xf7) | 0x10); + + } else if (!strncmp(monitor_port, "2", 1)) { /* 2 - Double link LVDS */ + xres = 1280; + pixel_format = 0x88883316; + gamma_fix = 1; + out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val & 0xe7); + + } else { /* DVI */ + xres = 1280; + pixel_format = 0x88882317; + gamma_fix = 0; + out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x08); + } + + fsl_diu_init(xres, pixel_format, gamma_fix, + (unsigned char *)FSL_Logo_BMP); +} + +int mpc8610diu_init_show_bmp(cmd_tbl_t *cmdtp, + int flag, int argc, char *argv[]) +{ + unsigned int addr; + + if (argc < 2) { + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + if (!strncmp(argv[1],"init",4)) { + mpc8610hpcd_diu_init(); + } else { + addr = simple_strtoul(argv[1], NULL, 16); + fsl_diu_clear_screen(); + fsl_diu_display_bmp((unsigned char *)addr, 0, 0, 0); + } + + return 0; +} + +U_BOOT_CMD( + diufb, CFG_MAXARGS, 1, mpc8610diu_init_show_bmp, + "diufb init | addr - Init or Display BMP file\n", + "init\n - initialize DIU\n" + "addr\n - display bmp at address 'addr'\n" + ); +#endif /* CONFIG_FSL_DIU_FB */ diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 9fa42f32daa..00c94ef47df 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -21,6 +21,7 @@ #define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ +#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ #ifdef RUN_DIAG #define CFG_DIAG_ADDR 0xff800000 #endif @@ -38,7 +39,7 @@ #define CONFIG_SPD_EEPROM /* Use SPD for DDR */ #undef CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef #define CONFIG_NUM_DDR_CONTROLLERS 1 @@ -51,13 +52,14 @@ */ #define CFG_L2 #define L2_INIT 0 -#define L2_ENABLE (L2CR_L2E) +#define L2_ENABLE (L2CR_L2E |0x00100000 ) #ifndef CONFIG_SYS_CLK_FREQ #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) #endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_MISC_INIT_R 1 #undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ @@ -159,6 +161,7 @@ #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */ #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ +#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/ #define PIXIS_VCTL 0x10 /* VELA Control Register */ #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ @@ -208,7 +211,7 @@ #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 @@ -474,6 +477,9 @@ #undef CONFIG_WATCHDOG /* watchdog disabled */ +/*DIU Configuration*/ +#define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/ + /* * Miscellaneous configurable options */ @@ -621,7 +627,8 @@ "diuregs=md e002c000 1d\0" \ "dium=mw e002c01c\0" \ "diuerr=md e002c014 1\0" \ - "othbootargs=debug\0" \ + "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \ + "monitor=0-DVI\0" \ "pmregs=md e00e1000 2b\0" \ "lawregs=md e0000c08 4b\0" \ "lbcregs=md e0005000 36\0" \ @@ -641,7 +648,9 @@ "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ "dtbaddr=c00000\0" \ "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \ - "bdev=sda3\0" + "bdev=sda3\0" \ + "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\ + "monitor=0-DVI\0" #endif #define CONFIG_NFSBOOTCOMMAND \ -- cgit v1.3.1 From 070ba56115b4da63b46e974287fa4550d4023386 Mon Sep 17 00:00:00 2001 From: York Sun Date: Wed, 31 Oct 2007 14:59:04 -0500 Subject: 8610: Add console frame buffer support to FSL 8610 DIU driver. Add cfb console support to FSL 8610 DIU driver. Inspect board version from PIXIS to obtain correct pixel format. Use #define CONFIG_VIDEO in config file to enable fb console. To switch monitor, set monitor variable to 0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS followed by "diufb init". Preserve logo bitmap at the top of the fb console. Signed-off-by: York Sun Signed-off-by: Jon Loeliger --- board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c | 78 +++++++++++++++++++++++++-- include/configs/MPC8610HPCD.h | 20 +++++-- 2 files changed, 91 insertions(+), 7 deletions(-) (limited to 'include') diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c index 4449376789c..b70637f9402 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd_diu.c @@ -32,40 +32,55 @@ #include "../common/pixis.h" #include "../common/fsl_diu_fb.h" +#if defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) +#include +#include +#endif extern unsigned int FSL_Logo_BMP[]; +static int xres, yres; + void mpc8610hpcd_diu_init(void) { char *monitor_port; - int xres, gamma_fix; + int gamma_fix; unsigned int pixel_format; unsigned char tmp_val; + unsigned char pixis_arch; tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0); - monitor_port = getenv ("monitor"); + pixis_arch = in8(PIXIS_BASE + PIXIS_VER); + monitor_port = getenv("monitor"); if (!strncmp(monitor_port, "0", 1)) { /* 0 - DVI */ xres = 1280; - pixel_format = 0x88882317; + yres = 1024; + if (pixis_arch == 0x01) + pixel_format = 0x88882317; + else + pixel_format = 0x88883316; gamma_fix = 0; out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x08); } else if (!strncmp(monitor_port, "1", 1)) { /* 1 - Single link LVDS */ xres = 1024; + yres = 768; pixel_format = 0x88883316; gamma_fix = 0; out8(PIXIS_BASE + PIXIS_BRDCFG0, (tmp_val & 0xf7) | 0x10); } else if (!strncmp(monitor_port, "2", 1)) { /* 2 - Double link LVDS */ xres = 1280; + yres = 1024; pixel_format = 0x88883316; gamma_fix = 1; out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val & 0xe7); } else { /* DVI */ xres = 1280; + yres = 1024; pixel_format = 0x88882317; gamma_fix = 0; out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x08); @@ -86,7 +101,12 @@ int mpc8610diu_init_show_bmp(cmd_tbl_t *cmdtp, } if (!strncmp(argv[1],"init",4)) { +#if defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) + fsl_diu_clear_screen(); + drv_video_init(); +#else mpc8610hpcd_diu_init(); +#endif } else { addr = simple_strtoul(argv[1], NULL, 16); fsl_diu_clear_screen(); @@ -102,4 +122,56 @@ U_BOOT_CMD( "init\n - initialize DIU\n" "addr\n - display bmp at address 'addr'\n" ); + + +#if defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) + +/* + * The Graphic Device + */ +GraphicDevice ctfb; +void *video_hw_init(void) +{ + GraphicDevice *pGD = (GraphicDevice *) &ctfb; + struct fb_info *info; + + mpc8610hpcd_diu_init(); + + /* fill in Graphic device struct */ + sprintf(pGD->modeIdent, + "%dx%dx%d %ldkHz %ldHz", + xres, yres, 32, 64, 60); + + pGD->frameAdrs = (unsigned int)fsl_fb_open(&info); + pGD->winSizeX = xres; + pGD->winSizeY = yres - info->logo_height; + pGD->plnSizeX = pGD->winSizeX; + pGD->plnSizeY = pGD->winSizeY; + + pGD->gdfBytesPP = 4; + pGD->gdfIndex = GDF_32BIT_X888RGB; + + pGD->isaBase = 0; + pGD->pciBase = 0; + pGD->memSize = info->screen_size - info->logo_size; + + /* Cursor Start Address */ + pGD->dprBase = 0; + pGD->vprBase = 0; + pGD->cprBase = 0; + + return (void *)pGD; +} + +void video_set_lut (unsigned int index, /* color number */ + unsigned char r, /* red */ + unsigned char g, /* green */ + unsigned char b /* blue */ + ) +{ + return; +} + +#endif /* defined(CONFIG_VIDEO) || defined(CONFIG_CFB_CONSOLE) */ + #endif /* CONFIG_FSL_DIU_FB */ diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 00c94ef47df..f5d9c098c6b 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -22,6 +22,15 @@ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ + +/* video */ +#undef CONFIG_VIDEO + +#if defined(CONFIG_VIDEO) +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#endif + #ifdef RUN_DIAG #define CFG_DIAG_ADDR 0xff800000 #endif @@ -314,15 +323,17 @@ #define CONFIG_EEPRO100 #define CONFIG_TULIP -#if 0 /* TODO */ /************************************************************ * USB support ************************************************************/ -#define CONFIG_USB_OHCI 1 +#define CONFIG_PCI_OHCI 1 +#define CONFIG_USB_OHCI_NEW 1 #define CONFIG_USB_KEYBOARD 1 #define CFG_DEVICE_DEREGISTER -#define CFG_USB_INTERRUPT_POLL 1 -#endif +#define CFG_USB_EVENT_POLL 1 +#define CFG_USB_OHCI_SLOT_NAME "ohci_pci" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#define CFG_OHCI_SWAP_REG_ACCESS 1 #if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 @@ -472,6 +483,7 @@ #define CONFIG_CMD_PCI #define CONFIG_CMD_SCSI #define CONFIG_CMD_EXT2 +#define CONFIG_CMD_USB #endif -- cgit v1.3.1 From b53313dbfc74525d85f1e7e0102f902d5c863beb Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 9 Nov 2007 12:19:58 +0100 Subject: ppc4xx: Remove In:/Out:/Err: boot output for AMCC Kilauea Signed-off-by: Stefan Roese --- include/configs/kilauea.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 07f7eff39e5..ddd064ad1da 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -358,6 +358,7 @@ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ /*----------------------------------------------------------------------- * PCI stuff -- cgit v1.3.1 From 5ca9881aad8c413ac2a82868a5e3719178254502 Mon Sep 17 00:00:00 2001 From: Peter Pearse Date: Fri, 9 Nov 2007 15:24:26 +0000 Subject: Add apollon board support Signed-off-by: Kyungmin Park --- MAKEALL | 1 + Makefile | 5 +- board/apollon/Makefile | 48 +++ board/apollon/apollon.c | 608 ++++++++++++++++++++++++++++++++ board/apollon/config.mk | 25 ++ board/apollon/lowlevel_init.S | 337 ++++++++++++++++++ board/apollon/mem.c | 228 ++++++++++++ board/apollon/mem.h | 170 +++++++++ board/apollon/sys_info.c | 408 +++++++++++++++++++++ board/apollon/u-boot.lds | 64 ++++ include/asm-arm/arch-arm1136/mux.h | 2 + include/asm-arm/arch-arm1136/omap2420.h | 33 +- include/asm-arm/mach-types.h | 13 + include/configs/apollon.h | 238 +++++++++++++ 14 files changed, 2175 insertions(+), 5 deletions(-) create mode 100644 board/apollon/Makefile create mode 100644 board/apollon/apollon.c create mode 100644 board/apollon/config.mk create mode 100644 board/apollon/lowlevel_init.S create mode 100644 board/apollon/mem.c create mode 100644 board/apollon/mem.h create mode 100644 board/apollon/sys_info.c create mode 100644 board/apollon/u-boot.lds create mode 100644 include/configs/apollon.h (limited to 'include') diff --git a/MAKEALL b/MAKEALL index 20e81370f7c..52f3cd34783 100755 --- a/MAKEALL +++ b/MAKEALL @@ -476,6 +476,7 @@ LIST_ARM10=" \ LIST_ARM11=" \ cp1136 \ omap2420h4 \ + apollon \ " ######################################################################### diff --git a/Makefile b/Makefile index c0821d87aac..e2a367eaf7c 100644 --- a/Makefile +++ b/Makefile @@ -2376,9 +2376,12 @@ zylonite_config : ######################################################################### ## ARM1136 Systems ######################################################################### -omap2420h4_config : unconfig +omap2420h4_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 +apollon_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm1136 apollon + #======================================================================== # i386 #======================================================================== diff --git a/board/apollon/Makefile b/board/apollon/Makefile new file mode 100644 index 00000000000..5348f2d3025 --- /dev/null +++ b/board/apollon/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := apollon.o mem.o sys_info.o +SOBJS := lowlevel_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend diff --git a/board/apollon/apollon.c b/board/apollon/apollon.c new file mode 100644 index 00000000000..e2c62772575 --- /dev/null +++ b/board/apollon/apollon.c @@ -0,0 +1,608 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics. + * Kyungmin Park + * + * Derived from omap2420 + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +void wait_for_command_complete(unsigned int wd_base); + +/******************************************************* + * Routine: delay + * Description: spinning delay to use before udelay works +******************************************************/ +static inline void delay(unsigned long loops) { + __asm__ volatile ("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); } + +/***************************************** + * Routine: board_init + * Description: Early hardware init. + *****************************************/ +int board_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gpmc_init(); /* in SRAM or SDRM, finish GPMC */ + + gd->bd->bi_arch_number = 919; + /* adress of boot parameters */ + gd->bd->bi_boot_params = (OMAP2420_SDRC_CS0 + 0x100); + + return 0; +} + +/********************************************************** + * Routine: s_init + * Description: Does early system init of muxing and clocks. + * - Called path is with sram stack. + **********************************************************/ +void s_init(void) +{ + + watchdog_init(); + set_muxconf_regs(); + delay(100); + + peripheral_enable(); + icache_enable(); +} + +/******************************************************* + * Routine: misc_init_r + * Description: Init ethernet (done here so udelay works) +********************************************************/ +int misc_init_r(void) +{ + ether_init(); /* better done here so timers are init'ed */ + return (0); +} + +/**************************************** + * Routine: watchdog_init + * Description: Shut down watch dogs + *****************************************/ +void watchdog_init(void) +{ + /* There are 4 watch dogs. 1 secure, and 3 general purpose. + * The ROM takes care of the secure one. Of the 3 GP ones, + * 1 can reset us directly, the other 2 only generate MPU interrupts. + */ + __raw_writel(WD_UNLOCK1, WD2_BASE + WSPR); + wait_for_command_complete(WD2_BASE); + __raw_writel(WD_UNLOCK2, WD2_BASE + WSPR); + +#define MPU_WD_CLOCKED 1 +#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite */ + __raw_writel(WD_UNLOCK1, WD3_BASE + WSPR); + wait_for_command_complete(WD3_BASE); + __raw_writel(WD_UNLOCK2, WD3_BASE + WSPR); + + __raw_writel(WD_UNLOCK1, WD4_BASE + WSPR); + wait_for_command_complete(WD4_BASE); + __raw_writel(WD_UNLOCK2, WD4_BASE + WSPR); +#endif +} + +/****************************************************** + * Routine: wait_for_command_complete + * Description: Wait for posting to finish on watchdog +******************************************************/ +void wait_for_command_complete(unsigned int wd_base) { + int pending = 1; + do { + pending = __raw_readl(wd_base + WWPS); + } while (pending); +} + +/******************************************************************* + * Routine:ether_init + * Description: take the Ethernet controller out of reset and wait + * for the EEPROM load to complete. + ******************************************************************/ +void ether_init(void) +{ +#ifdef CONFIG_DRIVER_LAN91C96 + int cnt = 20; + + __raw_writeb(0x03, OMAP2420_CTRL_BASE + 0x0f2); /*protect->gpio74 */ + + __raw_writew(0x0, LAN_RESET_REGISTER); + do { + __raw_writew(0x1, LAN_RESET_REGISTER); + udelay(100); + if (cnt == 0) { + printf("1. eth reset err\n"); + goto eth_reset_err_out; + } + --cnt; + } while (__raw_readw(LAN_RESET_REGISTER) != 0x1); + + cnt = 20; + + do { + __raw_writew(0x0, LAN_RESET_REGISTER); + udelay(100); + if (cnt == 0) { + printf("2. eth reset err\n"); + goto eth_reset_err_out; + } + --cnt; + } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000); + udelay(1000); + + *((volatile unsigned char *)ETH_CONTROL_REG) &= ~0x01; + udelay(1000); + +eth_reset_err_out: + return; +#endif +} + +/********************************************** + * Routine: dram_init + * Description: sets uboots idea of sdram size +**********************************************/ +int dram_init(void) +{ + DECLARE_GLOBAL_DATA_PTR; + unsigned int size0 = 0, size1 = 0; + u32 mtype, btype, rev = 0, cpu = 0; +#define NOT_EARLY 0 + + btype = get_board_type(); + mtype = get_mem_type(); + rev = get_cpu_rev(); + cpu = get_cpu_type(); + + display_board_info(btype); + + if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) { + printf("ddr combo\n"); + do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); /* init other chip select */ + } + + size0 = get_sdr_cs_size(SDRC_CS0_OSET); + size1 = get_sdr_cs_size(SDRC_CS1_OSET); + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = size0; +#if CONFIG_NR_DRAM_BANKS > 1 + gd->bd->bi_dram[1].start = PHYS_SDRAM_1 + size0; + gd->bd->bi_dram[1].size = size1; +#endif + + return 0; +} + +/********************************************************** + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers + * specific to the hardware + *********************************************************/ +void set_muxconf_regs(void) +{ + muxSetupSDRC(); + muxSetupGPMC(); + muxSetupUsb0(); /* USB Device */ + muxSetupUsbHost(); /* USB Host */ + muxSetupUART1(); + muxSetupLCD(); + muxSetupMMCSD(); + muxSetupTouchScreen(); +} + +/***************************************************************** + * Routine: peripheral_enable + * Description: Enable the clks & power for perifs (GPT2, UART1,...) +******************************************************************/ +void peripheral_enable(void) +{ + unsigned int v, if_clks = 0, func_clks = 0; + + /* Enable GP2 timer. */ + if_clks |= BIT4 | BIT3; + func_clks |= BIT4 | BIT3; + v = __raw_readl(CM_CLKSEL2_CORE) | 0x4 | 0x2; /* Sys_clk input OMAP2420_GPT2 */ + __raw_writel(v, CM_CLKSEL2_CORE); + __raw_writel(0x1, CM_CLKSEL_WKUP); + +#ifdef CFG_NS16550 + /* Enable UART1 clock */ + func_clks |= BIT21; + if_clks |= BIT21; +#endif + v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */ + __raw_writel(v, CM_ICLKEN1_CORE); + v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */ + __raw_writel(v, CM_FCLKEN1_CORE); + delay(1000); + +#ifndef KERNEL_UPDATED + { +#define V1 0xffffffff +#define V2 0x00000007 + + __raw_writel(V1, CM_FCLKEN1_CORE); + __raw_writel(V2, CM_FCLKEN2_CORE); + __raw_writel(V1, CM_ICLKEN1_CORE); + __raw_writel(V1, CM_ICLKEN2_CORE); + } +#endif +} + +/**************************************** + * Routine: muxSetupUsb0 (ostboot) + * Description: Setup usb muxing + *****************************************/ +void muxSetupUsb0(void) +{ + volatile uint8 *MuxConfigReg; + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0; + *MuxConfigReg &= (uint8) (~0x1F); + + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT; + *MuxConfigReg &= (uint8) (~0x1F); +} + +#define CONTROL_PADCONF_USB1_RCV ((volatile uint8 *)0x480000EB) +#define CONTROL_PADCONF_USB1_TXEN ((volatile uint8 *)0x480000EC) +#define CONTROL_PADCONF_GPIO69 ((volatile uint8 *)0x480000ED) +#define CONTROL_PADCONF_GPIO70 ((volatile uint8 *)0x480000EE) + +#define CONTROL_PADCONF_GPIO102 ((volatile uint8 *)0x48000116) +#define CONTROL_PADCONF_GPIO103 ((volatile uint8 *)0x48000117) +#define CONTROL_PADCONF_GPIO104 ((volatile uint8 *)0x48000118) +#define CONTROL_PADCONF_GPIO105 ((volatile uint8 *)0x48000119) +/**************************************** + * Routine: muxSetupUSBHost (ostboot) + * Description: Setup USB Host muxing + *****************************************/ +void muxSetupUsbHost(void) +{ + volatile uint8 *MuxConfigReg; + + /* V19 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB1_RCV; + *MuxConfigReg = 1; + /* W20 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB1_TXEN; + *MuxConfigReg = 1; + /* N14 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO69; + *MuxConfigReg = 3; + /* P15 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO70; + *MuxConfigReg = 3; + + /* L18 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO102; + *MuxConfigReg = 3; + /* L19 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO103; + *MuxConfigReg = 3; + /* K15 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO104; + *MuxConfigReg = 3; + /* K14 */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO105; + *MuxConfigReg = 3; +} + +/**************************************** + * Routine: muxSetupUART1 (ostboot) + * Description: Set up uart1 muxing + *****************************************/ +void muxSetupUART1(void) +{ + volatile unsigned char *MuxConfigReg; + + /* UART1_CTS pin configuration, PIN = D21 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* UART1_RTS pin configuration, PIN = H21 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* UART1_TX pin configuration, PIN = L20 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* UART1_RX pin configuration, PIN = T21 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ +} + +/**************************************** + * Routine: muxSetupLCD (ostboot) + * Description: Setup lcd muxing + *****************************************/ +void muxSetupLCD(void) +{ + volatile unsigned char *MuxConfigReg; + + /* LCD_D0 pin configuration, PIN = Y7 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D1 pin configuration, PIN = P10 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D2 pin configuration, PIN = V8 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D3 pin configuration, PIN = Y8 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D4 pin configuration, PIN = W8 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D5 pin configuration, PIN = R10 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D6 pin configuration, PIN = Y9 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D7 pin configuration, PIN = V9 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D8 pin configuration, PIN = W9 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D9 pin configuration, PIN = P11 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D10 pin configuration, PIN = V10 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D11 pin configuration, PIN = Y10 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D12 pin configuration, PIN = W10 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D13 pin configuration, PIN = R11 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D14 pin configuration, PIN = V11 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D15 pin configuration, PIN = W11 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D16 pin configuration, PIN = P12 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_D17 pin configuration, PIN = R12 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_PCLK pin configuration, PIN = W6 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_VSYNC pin configuration, PIN = V7 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_HSYNC pin configuration, PIN = Y6 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* LCD_ACBIAS pin configuration, PIN = W7 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ +} + +/**************************************** + * Routine: muxSetupMMCSD (ostboot) + * Description: set up MMC muxing + *****************************************/ +void muxSetupMMCSD(void) +{ + volatile unsigned char *MuxConfigReg; + + /* SDMMC_CLKI pin configuration, PIN = H15 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_CLKO pin configuration, PIN = G19 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_CMD pin configuration, PIN = H18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* External pull-ups are present. */ + /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ + + /* SDMMC_DAT0 pin configuration, PIN = F20 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* External pull-ups are present. */ + /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ + + /* SDMMC_DAT1 pin configuration, PIN = H14 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* External pull-ups are present. */ + /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ + + /* SDMMC_DAT2 pin configuration, PIN = E19 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* External pull-ups are present. */ + /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ + + /* SDMMC_DAT3 pin configuration, PIN = D19 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* External pull-ups are present. */ + /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ + + /* SDMMC_DDIR0 pin configuration, PIN = F19 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_DDIR1 pin configuration, PIN = E20 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_DDIR2 pin configuration, PIN = F18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_DDIR3 pin configuration, PIN = E18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SDMMC_CDIR pin configuration, PIN = G18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ +} + +/****************************************** + * Routine: muxSetupTouchScreen (ostboot) + * Description: Set up touch screen muxing +*******************************************/ +void muxSetupTouchScreen(void) +{ + volatile unsigned char *MuxConfigReg; + + /* SPI1_CLK pin configuration, PIN = U18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SPI1_MOSI pin configuration, PIN = V20 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SPI1_MISO pin configuration, PIN = T18 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + + /* SPI1_nCS0 pin configuration, PIN = U19 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0; + *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + +#define CONTROL_PADCONF_GPIO85 CONTROL_PADCONF_SPI1_NCS1 + + /* PEN_IRQ pin configuration, PIN = N15 */ + MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_GPIO85; + *MuxConfigReg = 0x03; /* Mode = 3, PUPD=Disabled */ +} + +/*************************************************************** + * Routine: muxSetupGPMC (ostboot) + * Description: Configures balls which cam up in protected mode +***************************************************************/ +void muxSetupGPMC(void) +{ + volatile uint8 *MuxConfigReg; + volatile unsigned int *MCR = (volatile unsigned int *)0x4800008C; + + /* gpmc_io_dir */ + *MCR = 0x19000000; + + /* NOR FLASH CS0 */ + /* signal - Gpmc_clk; + pin - J4; offset - 0x0088; mode - 0; Byte-3 Pull/up - N/A */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3; + *MuxConfigReg = 0x00; + + /* MPDB(Multi Port Debug Port) CS1 */ + /* signal - gpmc_ncs1; + pin - N8; offset - 0x008C; mode - 0; Byte-1 Pull/up - N/A */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1; + *MuxConfigReg = 0x00; + + /* signal - Gpmc_ncs2; + pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2; + *MuxConfigReg = 0x00; + + /* signal - Gpmc_ncs3; + pin - N2; offset - 0x008C; mode - 0; Byte-3 Pull/up - N/A */ + MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3; + *MuxConfigReg = 0x00; + + MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000090); + *MuxConfigReg = 0x00; + MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000091); + *MuxConfigReg = 0x00; + MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000092); + *MuxConfigReg = 0x00; + MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000093); + *MuxConfigReg = 0x00; +} + +/**************************************************************** + * Routine: muxSetupSDRC (ostboot) + * Description: Configures balls which come up in protected mode +****************************************************************/ +void muxSetupSDRC(void) +{ + /* It's set by IPL */ +} diff --git a/board/apollon/config.mk b/board/apollon/config.mk new file mode 100644 index 00000000000..417b954a7fc --- /dev/null +++ b/board/apollon/config.mk @@ -0,0 +1,25 @@ +# +# (C) Copyright 2005-2007 +# Samsung Electronics +# +# Samsung December board with OMAP2420 (ARM1136) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# December has 1 bank of 128MB mDDR-SDRAM on CS0 +# December has 1 bank of 00MB mDDR-SDRAM on CS1 +# Physical Address: +# 8000'0000 (bank0) +# A000/0000 (bank1) ES2 will be configurable +# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# For use with external or internal boots. +TEXT_BASE = 0x80e80000 + +# Used with full SRAM boot. +# This is either with a GP system or a signed boot image. +# easiest, and safest way to go if you can. +#TEXT_BASE = 0x40270000 + +# Handy to get symbols to debug ROM version. +#TEXT_BASE = 0x0 +#TEXT_BASE = 0x08000000 diff --git a/board/apollon/lowlevel_init.S b/board/apollon/lowlevel_init.S new file mode 100644 index 00000000000..76762599b1d --- /dev/null +++ b/board/apollon/lowlevel_init.S @@ -0,0 +1,337 @@ +/* + * Board specific setup info + * + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include "mem.h" + +#define APOLLON_CS0_BASE 0x00000000 + +#ifdef PRCM_CONFIG_I +# define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 +# define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 +# define SDRC_RFR_CTRL_0_VAL 0x00044C01 +#elif defined(PRCM_CONFIG_II) +# define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 +# define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C +# define SDRC_RFR_CTRL_0_VAL 0x00030001 +#endif + +#define SDRAM_BASE_ADDRESS 0x80008000 + +_TEXT_BASE: + .word TEXT_BASE /* sdram load addr from config.mk */ + +.globl lowlevel_init +lowlevel_init: + +#ifdef CFG_NOR_BOOT + /* Check running in SDRAM */ + mov r0, pc, lsr #28 + cmp r0, #8 + beq prcm_setup + +flash_setup: + /* In Flash */ + ldr r0, =WD2_BASE + ldr r1, =WD_UNLOCK1 + str r1, [r0, #WSPR] + + ldr r1, =WD_UNLOCK2 + str r1, [r0, #WSPR] + + /* Pin muxing for SDRC */ + mov r1, #0x00 + ldr r0, =0x480000A1 /* ball C12, mode 0 */ + strb r1, [r0] + + ldr r0, =0x48000032 /* ball D11, mode 0 */ + strb r1, [r0] + + ldr r0, =0x480000A3 /* ball B13, mode 0 */ + strb r1, [r0] + + /* SDRC setting */ + ldr r0, =OMAP2420_SDRC_BASE + ldr r1, =0x00000010 + str r1, [r0, #0x10] + + ldr r1, =0x00000100 + str r1, [r0, #0x44] + + /* SDRC CS0 configuration */ + ldr r1, =0x00d04011 + str r1, [r0, #0x80] + + ldr r1, =SDRC_ACTIM_CTRLA_0_VAL + str r1, [r0, #0x9C] + + ldr r1, =SDRC_ACTIM_CTRLB_0_VAL + str r1, [r0, #0xA0] + + ldr r1, =SDRC_RFR_CTRL_0_VAL + str r1, [r0, #0xA4] + + ldr r1, =0x00000041 + str r1, [r0, #0x70] + + /* Manual command sequence */ + ldr r1, =0x00000007 + str r1, [r0, #0xA8] + + ldr r1, =0x00000000 + str r1, [r0, #0xA8] + + ldr r1, =0x00000001 + str r1, [r0, #0xA8] + + ldr r1, =0x00000002 + str r1, [r0, #0xA8] + str r1, [r0, #0xA8] + + /* + * CS0 SDRC Mode register + * Burst length = 4 - DDR memory + * Serial mode + * CAS latency = 3 + */ + ldr r1, =0x00000032 + str r1, [r0, #0x84] + + /* Note: You MUST set EMR values */ + /* EMR1 & EMR2 */ + ldr r1, =0x00000000 + str r1, [r0, #0x88] + str r1, [r0, #0x8C] + +#ifdef OLD_SDRC_DLLA_CTRL + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00007306 + str r1, [r0, #0x60] + + ldr r1, =0x00007303 + str r1, [r0, #0x60] +#else + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x60] + + ldr r1, =0x00000503 + str r1, [r0, #0x60] +#endif + +#ifdef __BROKEN_FEATURE__ + /* SDRC_DLLB_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x68] + + ldr r1, =0x00000503 + str r1, [r0, #0x68] +#endif + + /* little delay after init */ + mov r2, #0x1800 +1: + subs r2, r2, #0x1 + bne 1b + + /* Setup base address */ + ldr r0, =0x00000000 /* NOR address */ + ldr r1, =SDRAM_BASE_ADDRESS /* SDRAM address */ + ldr r2, =0x20000 /* Size: 128KB */ + +copy_loop: + ldmia r0!, {r3-r10} + stmia r1!, {r3-r10} + cmp r0, r2 + ble copy_loop + + ldr r1, =SDRAM_BASE_ADDRESS + mov lr, pc + mov pc, r1 +#endif + +prcm_setup: + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x544] /* CLKSEL2_PLL */ + bic r1, r1, #0x03 + orr r1, r1, #0x02 + str r1, [r0, #0x544] + + ldr r1, [r0, #0x500] + bic r1, r1, #0x03 + orr r1, r1, #0x01 + str r1, [r0, #0x500] + + ldr r1, [r0, #0x140] + bic r1, r1, #0x1f + orr r1, r1, #0x02 + str r1, [r0, #0x140] + +#ifdef PRCM_CONFIG_I + ldr r1, =0x000003C3 +#else + ldr r1, =0x00000343 +#endif + str r1, [r0, #0x840] + + ldr r1, =0x00000002 + str r1, [r0, #0x340] + + ldr r1, =CM_CLKSEL1_CORE +#ifdef PRCM_CONFIG_I + ldr r2, =0x08300C44 +#else + ldr r2, =0x04600C26 +#endif + str r2, [r1] + + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x01 + bne clkvalid + + b . + +clkvalid: + mov r1, #0x01 + str r1, [r0, #0x080] + +waitvalid: + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x00 + bne waitvalid + + ldr r0, =CM_CLKSEL1_PLL +#ifdef PRCM_CONFIG_I + ldr r1, =0x01837100 +#else + ldr r1, =0x01832100 +#endif + str r1, [r0] + + ldr r0, =PRCM_CLKCFG_CTRL + mov r1, #0x01 + str r1, [r0] + mov r6, #0x50 +loop1: + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop1 + + ldr r0, =CM_CLKEN_PLL + mov r1, #0x0f + str r1, [r0] + + mov r6, #0x100 +loop2: + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop2 + + ldr r0, =0x48008200 + ldr r1, =0xbfffffff + str r1, [r0] + + ldr r0, =0x48008210 + ldr r1, =0xfffffff9 + str r1, [r0] + + ldr r0, =0x4806a004 + ldr r1, =0x00 + strb r1, [r0] + + ldr r0, =0x4806a020 + ldr r1, =0x07 + strb r1, [r0] + + ldr r0, =0x4806a00c + ldr r1, =0x83 + strb r1, [r0] + + ldr r0, =0x4806a000 + ldr r1, =0x1a + strb r1, [r0] + + ldr r0, =0x4806a004 + ldr r1, =0x00 + strb r1, [r0] + + ldr r0, =0x4806a00c + ldr r1, =0x03 + strb r1, [r0] + + ldr r0, =0x4806a010 + ldr r1, =0x03 + strb r1, [r0] + + ldr r0, =0x4806a008 + ldr r1, =0x04 + strb r1, [r0] + + ldr r0, =0x4806a020 + ldr r1, =0x00 + strb r1, [r0] + +#if 0 + ldr r0, =0x4806a000 + mov r1, #'u' + strb r1, [r0] +#endif + +#if 0 + /* LED0 OFF */ + ldr r3, =0x480000E5 + mov r4, #0x0b + strb r4, [r3] +#endif + + ldr sp, SRAM_STACK + str ip, [sp] /* stash old link register */ + mov ip, lr /* save link reg across call */ + bl s_init /* go setup pll,mux,memory */ + ldr ip, [sp] /* restore save ip */ + mov lr, ip /* restore link reg */ + + /* map interrupt controller */ + ldr r0, VAL_INTH_SETUP + mcr p15, 0, r0, c15, c2, 4 + + /* back to arch calling code */ + mov pc, lr + + /* the literal pools origin */ + .ltorg + +VAL_INTH_SETUP: + .word PERIFERAL_PORT_BASE +SRAM_STACK: + .word LOW_LEVEL_SRAM_STACK diff --git a/board/apollon/mem.c b/board/apollon/mem.c new file mode 100644 index 00000000000..8154d118120 --- /dev/null +++ b/board/apollon/mem.c @@ -0,0 +1,228 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park + * + * Derived from omap2420 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "mem.h" + +/************************************************************ + * sdelay() - simple spin loop. Will be constant time as + * its generally used in 12MHz bypass conditions only. This + * is necessary until timers are accessible. + * + * not inline to increase chances its in cache when called +*************************************************************/ +void sdelay(unsigned long loops) +{ + __asm__ volatile ("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); +} + +/***************************************************************************** + * prcm_init() - inits clocks for PRCM as defined in clocks.h + * (config II default). Called from SRAM, or Flash (using temp SRAM stack). + *****************************************************************************/ +void prcm_init(void) +{ +} + +/************************************************************************** + * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow + * command line mem=xyz use all memory with out discontigious support + * compiled in. Could do it at the ATAG, but there really is two banks... + * Called as part of 2nd phase DDR init. + **************************************************************************/ +void make_cs1_contiguous(void) +{ + u32 size, a_add_low, a_add_high; + + size = get_sdr_cs_size(SDRC_CS0_OSET); + size /= SZ_32M; /* find size to offset CS1 */ + a_add_high = (size & 3) << 8; /* set up low field */ + a_add_low = (size & 0x3C) >> 2; /* set up high field */ + __raw_writel((a_add_high | a_add_low), SDRC_CS_CFG); +} + +/******************************************************** + * mem_ok() - test used to see if timings are correct + * for a part. Helps in gussing which part + * we are currently using. + *******************************************************/ +u32 mem_ok(void) +{ + u32 val1, val2; + u32 pattern = 0x12345678; + + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 0x400); /* clear pos A */ + __raw_writel(pattern, OMAP2420_SDRC_CS0); /* pattern to pos B */ + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 4); /* remove pattern off the bus */ + val1 = __raw_readl(OMAP2420_SDRC_CS0 + 0x400); /* get pos A value */ + val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */ + + if ((val1 != 0) || (val2 != pattern)) /* see if pos A value changed */ + return (0); + else + return (1); +} + +/******************************************************** + * sdrc_init() - init the sdrc chip selects CS0 and CS1 + * - early init routines, called from flash or + * SRAM. + *******************************************************/ +void sdrc_init(void) +{ +#define EARLY_INIT 1 + /* only init up first bank here */ + do_sdrc_init(SDRC_CS0_OSET, EARLY_INIT); +} + +/************************************************************************* + * do_sdrc_init(): initialize the SDRAM for use. + * -called from low level code with stack only. + * -code sets up SDRAM timing and muxing for 2422 or 2420. + * -optimal settings can be placed here, or redone after i2c + * inspection of board info + * + * This is a bit ugly, but should handle all memory moduels + * used with the APOLLON. The first time though this code from s_init() + * we configure the first chip select. Later on we come back and + * will configure the 2nd chip select if it exists. + * + **************************************************************************/ +void do_sdrc_init(u32 offset, u32 early) +{ +} + +/***************************************************** + * gpmc_init(): init gpmc bus + * Init GPMC for x16, MuxMode (SDRAM in x32). + * This code can only be executed from SRAM or SDRAM. + *****************************************************/ +void gpmc_init(void) +{ + u32 mux = 0, mtype, mwidth, rev, tval; + + rev = get_cpu_rev(); + if (rev == CPU_2420_2422_ES1) + tval = 1; + else + tval = 0; /* disable bit switched meaning */ + + /* global settings */ + __raw_writel(0x10, GPMC_SYSCONFIG); /* smart idle */ + __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */ + __raw_writel(tval, GPMC_TIMEOUT_CONTROL); /* timeout disable */ +#ifdef CFG_NAND_BOOT + __raw_writel(0x001, GPMC_CONFIG); /* set nWP, disable limited addr */ +#else + __raw_writel(0x111, GPMC_CONFIG); /* set nWP, disable limited addr */ +#endif + + /* discover bus connection from sysboot */ + if (is_gpmc_muxed() == GPMC_MUXED) + mux = BIT9; + mtype = get_gpmc0_type(); + mwidth = get_gpmc0_width(); + + /* setup cs0 */ + __raw_writel(0x0, GPMC_CONFIG7_0); /* disable current map */ + sdelay(1000); + +#ifdef CFG_NOR_BOOT + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_3, GPMC_CONFIG1_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_3, GPMC_CONFIG2_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_3, GPMC_CONFIG3_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_3, GPMC_CONFIG4_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_3, GPMC_CONFIG5_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_3, GPMC_CONFIG6_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_0); #else + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_0 | mux | mtype | mwidth, + GPMC_CONFIG1_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0); + /* enable new mapping */ + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0); +#endif + sdelay(2000); + + /* setup cs1 */ + __raw_writel(0, GPMC_CONFIG7_1); /* disable any mapping */ + sdelay(1000); + + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_1, GPMC_CONFIG1_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_1, GPMC_CONFIG2_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_1, GPMC_CONFIG3_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_1, GPMC_CONFIG4_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_1, GPMC_CONFIG5_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_1, GPMC_CONFIG6_1); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_1, GPMC_CONFIG7_1); + sdelay(2000); + + /* setup cs2 */ + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_0 | mux | mtype | mwidth, + GPMC_CONFIG1_2); + /* It's same as cs 0 */ + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_0, GPMC_CONFIG3_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_2); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_2); +#ifdef CFG_NOR_BOOT + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_2); +#else + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_2, GPMC_CONFIG7_2); +#endif + +#ifndef CFG_NOR_BOOT + /* setup cs3 */ + __raw_writel(0, GPMC_CONFIG7_3); /* disable any mapping */ + sdelay(1000); + + __raw_writel(APOLLON_24XX_GPMC_CONFIG1_3, GPMC_CONFIG1_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG2_3, GPMC_CONFIG2_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG3_3, GPMC_CONFIG3_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG4_3, GPMC_CONFIG4_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG5_3, GPMC_CONFIG5_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG6_3, GPMC_CONFIG6_3); + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_3); +#endif + +#ifndef ASYNC_NOR + __raw_writew(0xaa, (APOLLON_CS3_BASE + 0xaaa)); + __raw_writew(0x55, (APOLLON_CS3_BASE + 0x554)); + __raw_writew(0xc0, (APOLLON_CS3_BASE | SYNC_NOR_VALUE)); +#endif + sdelay(2000); +} diff --git a/board/apollon/mem.h b/board/apollon/mem.h new file mode 100644 index 00000000000..aed7e1d64d2 --- /dev/null +++ b/board/apollon/mem.h @@ -0,0 +1,170 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _APOLLON_OMAP24XX_MEM_H_ +#define _APOLLON_OMAP24XX_MEM_H_ + +/* Slower full frequency range default timings for x32 operation*/ +#define APOLLON_2420_SDRC_SHARING 0x00000100 +#define APOLLON_2420_SDRC_MDCFG_0_DDR 0x00d04011 +#define APOLLON_2420_SDRC_MR_0_DDR 0x00000032 + +/* optimized timings good for current shipping parts */ +#define APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz 0x4A59B485 +#define APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz 0x0000000C + +#define APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz 0x7BA35907 +#define APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz 0x00000013 + +#define APOLLON_242X_SDRC_RFR_CTRL_100MHz 0x00030001 +#define APOLLON_242X_SDRC_RFR_CTRL_166MHz 0x00044C01 + +#define APOLLON_242x_SDRC_DLLAB_CTRL_100MHz 0x00007306 +#define APOLLON_242x_SDRC_DLLAB_CTRL_166MHz 0x00000506 + +#ifdef PRCM_CONFIG_I +# define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz +# define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz +# define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_166MHz +# define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_166MHz +#elif PRCM_CONFIG_II +# define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz +# define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz +# define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_100MHz +# define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_100MHz +#endif + +/* GPMC settings */ +#ifdef PRCM_CONFIG_I /* L3 at 165MHz */ +/* CS0: OneNAND */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x00000001 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x000c1000 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00030400 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x0b841006 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x020f0c11 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000e40|(APOLLON_CS0_BASE >> 24)) + +/* CS1: Ethernet */ +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00011200 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001F1F01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C0b1C0a +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041F1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) + +/* CS2: OneNAND */ +/* It's same as CS0 */ +# define APOLLON_24XX_GPMC_CONFIG7_2 (0x00000e40|(APOLLON_CS2_BASE >> 24)) + +/* CS3: NOR */ +#ifdef ASYNC_NOR +# define APOLLON_24XX_GPMC_CONFIG1_3 0x00021201 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00121601 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00040401 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x12061605 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01151317 +#else +# define SYNC_NOR_VALUE 0x24aaa +# define APOLLON_24XX_GPMC_CONFIG1_3 0xe5011211 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00090b01 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00020201 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x09030b03 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x010a0a0c +#endif /* ASYNC_NOR */ +# define APOLLON_24XX_GPMC_CONFIG6_3 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_3 (0x00000e40|(APOLLON_CS3_BASE >> 24)) +#endif /* endif PRCM_CONFIG_I */ + +#ifdef PRCM_CONFIG_II /* L3 at 100MHz */ +/* CS0: OneNAND */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x00000001 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00081080 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00030300 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x08041004 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x020b0910 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000C40|(APOLLON_CS0_BASE >> 24)) + +/* CS1: ethernet */ +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00401203 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001F1F01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C091C09 +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041F1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) + +/* CS2: OneNAND */ +/* It's same as CS0 */ +# define APOLLON_24XX_GPMC_CONFIG7_2 (0x00000e40|(APOLLON_CS2_BASE >> 24)) + +/* CS3: NOR */ +#define ASYNC_NOR +#ifdef ASYNC_NOR +# define APOLLON_24XX_GPMC_CONFIG1_3 0x00021201 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00121601 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00040401 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x12061605 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01151317 +#else +# define SYNC_NOR_VALUE 0x24aaa +# define APOLLON_24XX_GPMC_CONFIG1_3 0xe1001202 +# define APOLLON_24XX_GPMC_CONFIG2_3 0x00151501 +# define APOLLON_24XX_GPMC_CONFIG3_3 0x00050501 +# define APOLLON_24XX_GPMC_CONFIG4_3 0x0e070e07 +# define APOLLON_24XX_GPMC_CONFIG5_3 0x01131F1F +#endif /* ASYNC_NOR */ +# define APOLLON_24XX_GPMC_CONFIG6_3 0x00000000 +# define APOLLON_24XX_GPMC_CONFIG7_3 (0x00000C40|(APOLLON_CS3_BASE >> 24)) +#endif /* endif PRCM_CONFIG_II */ + +#ifdef PRCM_CONFIG_III /* L3 at 133MHz */ +# ifdef CFG_NAND_BOOT +# define APOLLON_24XX_GPMC_CONFIG1_0 0x0 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00141400 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00141400 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x0F010F01 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x010C1414 +# define APOLLON_24XX_GPMC_CONFIG6_0 0x00000A80 +# else /* NOR boot */ +# define APOLLON_24XX_GPMC_CONFIG1_0 0x3 +# define APOLLON_24XX_GPMC_CONFIG2_0 0x00151501 +# define APOLLON_24XX_GPMC_CONFIG3_0 0x00060602 +# define APOLLON_24XX_GPMC_CONFIG4_0 0x10081008 +# define APOLLON_24XX_GPMC_CONFIG5_0 0x01131F1F +# define APOLLON_24XX_GPMC_CONFIG6_0 0x000004c4 +# endif /* endif CFG_NAND_BOOT */ +# define APOLLON_24XX_GPMC_CONFIG7_0 (0x00000C40|(APOLLON_CS0_BASE >> 24)) +# define APOLLON_24XX_GPMC_CONFIG1_1 0x00011000 +# define APOLLON_24XX_GPMC_CONFIG2_1 0x001f1f01 +# define APOLLON_24XX_GPMC_CONFIG3_1 0x00080803 +# define APOLLON_24XX_GPMC_CONFIG4_1 0x1C091C09 +# define APOLLON_24XX_GPMC_CONFIG5_1 0x041f1F1F +# define APOLLON_24XX_GPMC_CONFIG6_1 0x000004C4 +# define APOLLON_24XX_GPMC_CONFIG7_1 (0x00000F40|(APOLLON_CS1_BASE >> 24)) +#endif /* endif CFG_PRCM_III */ + +#endif /* endif _APOLLON_OMAP24XX_MEM_H_ */ diff --git a/board/apollon/sys_info.c b/board/apollon/sys_info.c new file mode 100644 index 00000000000..60c35b4586b --- /dev/null +++ b/board/apollon/sys_info.c @@ -0,0 +1,408 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park + * + * Derived from omap2420 + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include /* get mem tables */ +#include +#include +#include + +/************************************************************************** + * get_prod_id() - get id info from chips + ***************************************************************************/ +static u32 get_prod_id(void) +{ + u32 p; + p = __raw_readl(PRODUCTION_ID); /* get production ID */ + return ((p & CPU_242X_PID_MASK) >> 16); +} +/************************************************************************** + * get_cpu_type() - low level get cpu type + * - no C globals yet. + * - just looking to say if this is a 2422 or 2420 or ... + * - to start with we will look at switch settings.. + * - 2422 id's same as 2420 for ES1 will rely on H4 board characteristics + * (mux for 2420, non-mux for 2422). + ***************************************************************************/ +u32 get_cpu_type(void) +{ + u32 v; + + switch (get_prod_id()) { + case 1:; /* 2420 */ + case 2: + return (CPU_2420); + break; /* 2420 pop */ + case 4: + return (CPU_2422); + break; + case 8: + return (CPU_2423); + break; + default: + break; /* early 2420/2422's unmarked */ + } + + v = __raw_readl(TAP_IDCODE_REG); + v &= CPU_24XX_ID_MASK; + if (v == CPU_2420_CHIPID) { /* currently 2420 and 2422 have same id */ + if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */ + return (CPU_2420); + else + return (CPU_2422); + } else + return (CPU_2420); /* don't know, say 2420 */ +} + +/****************************************** + * get_cpu_rev(void) - extract version info + ******************************************/ +u32 get_cpu_rev(void) +{ + u32 v; + v = __raw_readl(TAP_IDCODE_REG); + v = v >> 28; + return (v + 1); /* currently 2422 and 2420 match up */ +} + +/**************************************************** + * is_mem_sdr() - return 1 if mem type in use is SDR + ****************************************************/ +u32 is_mem_sdr(void) +{ + volatile u32 *burst = (volatile u32 *)(SDRC_MR_0 + SDRC_CS0_OSET); + if (*burst == H4_2420_SDRC_MR_0_SDR) + return (1); + return (0); +} + +/*********************************************************** + * get_mem_type() - identify type of mDDR part used. + * 2422 uses stacked DDR, 2 parts CS0/CS1. + * 2420 may have 1 or 2, no good way to know...only init 1... + * when eeprom data is up we can select 1 more. + *************************************************************/ +u32 get_mem_type(void) +{ + u32 cpu, sdr = is_mem_sdr(); + + cpu = get_cpu_type(); + if (cpu == CPU_2422 || cpu == CPU_2423) + return (DDR_STACKED); + + if (get_prod_id() == 0x2) + return (XDR_POP); + + if (get_board_type() == BOARD_H4_MENELAUS) + if (sdr) + return (SDR_DISCRETE); + else + return (DDR_COMBO); + else if (sdr) /* SDP + SDR kit */ + return (SDR_DISCRETE); + else + return (DDR_DISCRETE); /* origional SDP */ +} + +/********************************************************************** + * + * get_cs0_size() - get size of chip select 0/1 + ************************************************************************/ +u32 get_sdr_cs_size(u32 offset) +{ + u32 size; + size = __raw_readl(SDRC_MCFG_0 + offset) >> 8; /* get ram size field */ + size &= 0x2FF; /* remove unwanted bits */ + size *= SZ_2M; /* find size in MB */ + return (size); +} + +/********************************************************************** + * + * get_board_type() - get board type based on current production stats. + * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info. + * when they are available we can get info from there. This should + * be correct of all known boards up until today. + ************************************************************************/ +u32 get_board_type(void) +{ +#if 0 + if (i2c_probe(I2C_MENELAUS) == 0) + return (BOARD_H4_MENELAUS); + else +#endif + return (BOARD_H4_SDP); +} + +/****************************************************************** + * get_sysboot_value() - get init word settings (dip switch on h4) +******************************************************************/ +inline u32 get_sysboot_value(void) +{ + return (0x00000FFF & __raw_readl(CONTROL_STATUS)); +} + +/*************************************************************************** + * get_gpmc0_base() - Return current address hardware will be + * fetching from. The below effectively gives what is correct, its a bit + * mis-leading compared to the TRM. For the most general case the mask + * needs to be also taken into account this does work in practice. + * - for u-boot we currently map: + * -- 0 to nothing, + * -- 4 to flash + * -- 8 to enent + * -- c to wifi + ***************************************************************************/ +u32 get_gpmc0_base(void) +{ + u32 b; + + b = __raw_readl(GPMC_CONFIG7_0); + b &= 0x1F; /* keep base [5:0] */ + b = b << 24; /* ret 0x0b000000 */ + return (b); +} + +/***************************************************************** + * is_gpmc_muxed() - tells if address/data lines are multiplexed + *****************************************************************/ +u32 is_gpmc_muxed(void) +{ + u32 mux; + mux = get_sysboot_value(); + if ((mux & (BIT0 | BIT1 | BIT2 | BIT3)) == (BIT0 | BIT2 | BIT3)) + return (GPMC_MUXED); /* NAND Boot mode */ + if (mux & BIT1) /* if mux'ed */ + return (GPMC_MUXED); + else + return (GPMC_NONMUXED); +} + +/************************************************************************ + * get_gpmc0_type() - read sysboot lines to see type of memory attached + ************************************************************************/ +u32 get_gpmc0_type(void) +{ + u32 type; + type = get_sysboot_value(); + if ((type & (BIT3 | BIT2)) == (BIT3 | BIT2)) + return (TYPE_NAND); + else + return (TYPE_NOR); +} + +/******************************************************************* + * get_gpmc0_width() - See if bus is in x8 or x16 (mainly for nand) + *******************************************************************/ +u32 get_gpmc0_width(void) +{ + u32 width; + width = get_sysboot_value(); + if ((width & 0xF) == (BIT3 | BIT2)) + return (WIDTH_8BIT); + else + return (WIDTH_16BIT); +} + +/********************************************************************* + * wait_on_value() - common routine to allow waiting for changes in + * volatile regs. + *********************************************************************/ +u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, +u32 bound) { + u32 i = 0, val; + do { + ++i; + val = __raw_readl(read_addr) & read_bit_mask; + if (val == match_value) + return (1); + if (i == bound) + return (0); + } while (1); +} + +/********************************************************************* + * display_board_info() - print banner with board info. + *********************************************************************/ +void display_board_info(u32 btype) +{ + char cpu_2420[] = "2420"; /* cpu type */ + char cpu_2422[] = "2422"; + char cpu_2423[] = "2423"; + char db_men[] = "Menelaus"; /* board type */ + char db_ip[] = "IP"; + char mem_sdr[] = "mSDR"; /* memory type */ + char mem_ddr[] = "mDDR"; + char t_tst[] = "TST"; /* security level */ + char t_emu[] = "EMU"; + char t_hs[] = "HS"; + char t_gp[] = "GP"; + char unk[] = "?"; + + char *cpu_s, *db_s, *mem_s, *sec_s; + u32 cpu, rev, sec; + + rev = get_cpu_rev(); + cpu = get_cpu_type(); + sec = get_device_type(); + + if (is_mem_sdr()) + mem_s = mem_sdr; + else + mem_s = mem_ddr; + + if (cpu == CPU_2423) + cpu_s = cpu_2423; + else if (cpu == CPU_2422) + cpu_s = cpu_2422; + else + cpu_s = cpu_2420; + + if (btype == BOARD_H4_MENELAUS) + db_s = db_men; + else + db_s = db_ip; + + switch (sec) { + case TST_DEVICE: + sec_s = t_tst; + break; + case EMU_DEVICE: + sec_s = t_emu; + break; + case HS_DEVICE: + sec_s = t_hs; + break; + case GP_DEVICE: + sec_s = t_gp; + break; + default: + sec_s = unk; + } + + printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev - 1); + printf("Samsung Apollon SDP Base Board + %s \n", mem_s); } + +/************************************************************************* + * get_board_rev() - setup to pass kernel board revision information + * 0 = 242x IP platform (first 2xx boards) + * 1 = 242x Menelaus platfrom. + *************************************************************************/ +u32 get_board_rev(void) +{ + u32 rev = 0; + u32 btype = get_board_type(); + + if (btype == BOARD_H4_MENELAUS) { + rev = 1; + } + return (rev); +} + +/******************************************************** + * get_base(); get upper addr of current execution + *******************************************************/ +u32 get_base(void) +{ + u32 val; + __asm__ __volatile__("mov %0, pc \n":"=r"(val)::"memory"); + val &= 0xF0000000; + val >>= 28; + return (val); +} + +/******************************************************** + * get_base2(); get 2upper addr of current execution + *******************************************************/ +u32 get_base2(void) +{ + u32 val; + __asm__ __volatile__("mov %0, pc \n":"=r"(val)::"memory"); + val &= 0xFF000000; + val >>= 24; + return (val); +} + +/******************************************************** + * running_in_flash() - tell if currently running in + * flash. + *******************************************************/ +u32 running_in_flash(void) +{ + if (get_base() < 4) + return (1); /* in flash */ + return (0); /* running in SRAM or SDRAM */ +} + +/******************************************************** + * running_in_sram() - tell if currently running in + * sram. + *******************************************************/ +u32 running_in_sram(void) +{ + if (get_base() == 4) + return (1); /* in SRAM */ + return (0); /* running in FLASH or SDRAM */ +} + +/******************************************************** + * running_in_sdram() - tell if currently running in + * flash. + *******************************************************/ +u32 running_in_sdram(void) +{ + if (get_base() > 4) + return (1); /* in sdram */ + return (0); /* running in SRAM or FLASH */ +} + +/************************************************************* + * running_from_internal_boot() - am I a signed NOR image. + *************************************************************/ +u32 running_from_internal_boot(void) +{ + u32 v, base; + + v = get_sysboot_value() & BIT3; + base = get_base2(); + /* if running at mask rom flash address and + * sysboot3 says this was an internal boot + */ + if ((base == 0x08) && v) + return (1); + else + return (0); +} + +/************************************************************* + * get_device_type(): tell if GP/HS/EMU/TST + *************************************************************/ +u32 get_device_type(void) +{ + int mode; + mode = __raw_readl(CONTROL_STATUS) & (BIT10 | BIT9 | BIT8); + return (mode >>= 8); +} diff --git a/board/apollon/u-boot.lds b/board/apollon/u-boot.lds new file mode 100644 index 00000000000..686d86b76ed --- /dev/null +++ b/board/apollon/u-boot.lds @@ -0,0 +1,64 @@ +/* + * + * Copyright (C) 2005-2007 Samsung Electronics + * Kyungin Park + * + * January 2004 - Changed to support H4 device + * Copyright (c) 2004 Texas Instruments + * + * (C) Copyright 2002 + * Gary Jennejohn, DENX Software Engineering, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/arm1136/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} + diff --git a/include/asm-arm/arch-arm1136/mux.h b/include/asm-arm/arch-arm1136/mux.h index 67c84190867..8bcd7a3685d 100644 --- a/include/asm-arm/arch-arm1136/mux.h +++ b/include/asm-arm/arch-arm1136/mux.h @@ -28,6 +28,7 @@ typedef unsigned int uint32; void muxSetupSDRC(void); void muxSetupGPMC(void); void muxSetupUsb0(void); +void muxSetupUsbHost(void); void muxSetupUart3(void); void muxSetupI2C1(void); void muxSetupUART1(void); @@ -70,6 +71,7 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_SPI1_SIMO ((volatile unsigned char *)0x48000100) #define CONTROL_PADCONF_SPI1_SOMI ((volatile unsigned char *)0x48000101) #define CONTROL_PADCONF_SPI1_NCS0 ((volatile unsigned char *)0x48000102) +#define CONTROL_PADCONF_SPI1_NCS1 ((volatile unsigned char *)0x48000103) #define CONTROL_PADCONF_MCBSP1_FSR ((volatile unsigned char *)0x4800010B) diff --git a/include/asm-arm/arch-arm1136/omap2420.h b/include/asm-arm/arch-arm1136/omap2420.h index d833035a4b3..0c11beccf68 100644 --- a/include/asm-arm/arch-arm1136/omap2420.h +++ b/include/asm-arm/arch-arm1136/omap2420.h @@ -77,6 +77,20 @@ #define GPMC_CONFIG5_1 (OMAP2420_GPMC_BASE+0xA0) #define GPMC_CONFIG6_1 (OMAP2420_GPMC_BASE+0xA4) #define GPMC_CONFIG7_1 (OMAP2420_GPMC_BASE+0xA8) +#define GPMC_CONFIG1_2 (OMAP2420_GPMC_BASE+0xC0) +#define GPMC_CONFIG2_2 (OMAP2420_GPMC_BASE+0xC4) +#define GPMC_CONFIG3_2 (OMAP2420_GPMC_BASE+0xC8) +#define GPMC_CONFIG4_2 (OMAP2420_GPMC_BASE+0xCC) +#define GPMC_CONFIG5_2 (OMAP2420_GPMC_BASE+0xD0) +#define GPMC_CONFIG6_2 (OMAP2420_GPMC_BASE+0xD4) +#define GPMC_CONFIG7_2 (OMAP2420_GPMC_BASE+0xD8) +#define GPMC_CONFIG1_3 (OMAP2420_GPMC_BASE+0xF0) +#define GPMC_CONFIG2_3 (OMAP2420_GPMC_BASE+0xF4) +#define GPMC_CONFIG3_3 (OMAP2420_GPMC_BASE+0xF8) +#define GPMC_CONFIG4_3 (OMAP2420_GPMC_BASE+0xFC) +#define GPMC_CONFIG5_3 (OMAP2420_GPMC_BASE+0x100) +#define GPMC_CONFIG6_3 (OMAP2420_GPMC_BASE+0x104) +#define GPMC_CONFIG7_3 (OMAP2420_GPMC_BASE+0x108) /* SMS */ #define OMAP2420_SMS_BASE 0x68008000 @@ -209,13 +223,24 @@ #define SRAM_OFFSET2 0x0000F800 #define SRAM_VECT_CODE (SRAM_OFFSET0|SRAM_OFFSET1|SRAM_OFFSET2) -#define LOW_LEVEL_SRAM_STACK 0x4020FFFC - -#define PERIFERAL_PORT_BASE 0x480FE003 - /* FPGA on Debug board.*/ #define ETH_CONTROL_REG (H4_CS1_BASE+0x30b) #define LAN_RESET_REGISTER (H4_CS1_BASE+0x1c) #endif /* endif CONFIG_2420H4 */ +#if defined(CONFIG_APOLLON) +#define APOLLON_CS0_BASE 0x00000000 /* OneNAND */ +#define APOLLON_CS1_BASE 0x08000000 /* ethernet */ +#define APOLLON_CS2_BASE 0x10000000 /* OneNAND */ +#define APOLLON_CS3_BASE 0x18000000 /* NOR */ + +#define ETH_CONTROL_REG (APOLLON_CS1_BASE + 0x30b) +#define LAN_RESET_REGISTER (APOLLON_CS1_BASE + 0x1c) +#endif /* endif CONFIG_APOLLON */ + +/* Common */ +#define LOW_LEVEL_SRAM_STACK 0x4020FFFC + +#define PERIFERAL_PORT_BASE 0x480FE003 + #endif diff --git a/include/asm-arm/mach-types.h b/include/asm-arm/mach-types.h index f6a5b4f1611..ab19047d059 100644 --- a/include/asm-arm/mach-types.h +++ b/include/asm-arm/mach-types.h @@ -737,6 +737,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_CB3RUFC 726 #define MACH_TYPE_MP2USB 727 #define MACH_TYPE_AT91SAM9261EK 848 +#define MACH_TYPE_OMAP_APOLLON 919 #define MACH_TYPE_PDNB3 1002 #define MACH_TYPE_AT91SAM9260EK 1099 #define MACH_TYPE_AT91RM9200DF 1119 @@ -6826,6 +6827,18 @@ extern unsigned int __machine_arch_type; # define machine_is_omap_h4() (0) #endif +#ifdef CONFIG_MACH_OMAP_APOLLON +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_OMAP_APOLLON +# endif +# define machine_is_omap_apollon() (machine_arch_type == MACH_TYPE_OMAP_APOLLON) +#else +# define machine_is_omap_apollon() (0) +#endif + #ifdef CONFIG_MACH_N10 # ifdef machine_arch_type # undef machine_arch_type diff --git a/include/configs/apollon.h b/include/configs/apollon.h new file mode 100644 index 00000000000..578153c8bf9 --- /dev/null +++ b/include/configs/apollon.h @@ -0,0 +1,238 @@ +/* + * (C) Copyright 2005-2007 + * Samsung Electronics, + * Kyungmin Park + * + * Configuration settings for the 2420 Samsung Apollon board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_ARM1136 1 /* This is an arm1136 CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP2420 1 /* which is in a 2420 */ +#define CONFIG_OMAP2420_APOLLON 1 +#define CONFIG_APOLLON 1 +#define CONFIG_APOLLON_PLUS 1 /* If you have apollon plus 1.x */ + +/* Clock config to target*/ +#define PRCM_CONFIG_I 1 +//#define PRCM_CONFIG_II 1 + +/* Boot method */ +/* uncomment if you use NOR boot */ +//#define CFG_NOR_BOOT 1 + +/* uncomment if you use NOR on CS3 */ +//#define CFG_USE_NOR 1 + +#ifdef CFG_NOR_BOOT +#undef CFG_USE_NOR +#define CFG_USE_NOR 1 +#endif + +#include /* get chip and board defs */ + +#define V_SCLK 12000000 + +/* input clock of PLL */ +/* the OMAP2420 H4 has 12MHz, 13MHz, or 19.2Mhz crystal input */ +#define CONFIG_SYS_CLK_FREQ V_SCLK + +#undef CONFIG_USE_IRQ /* no support for IRQs */ +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* + * Size of malloc() pool + */ +#define CFG_ENV_SIZE SZ_128K /* Total Size of Environment Sector */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + SZ_128K) +#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +/* + * SMC91c96 Etherent + */ +#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_LAN91C96_BASE (APOLLON_CS1_BASE+0x300) +#define CONFIG_LAN91C96_EXT_PHY + +/* + * NS16550 Configuration + */ +#define V_NS16550_CLK (48000000) /* 48MHz (APLL96/2) */ + +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE (-4) +#define CFG_NS16550_CLK V_NS16550_CLK /* 3MHz (1.5MHz*2) */ +#define CFG_NS16550_COM1 OMAP2420_UART1 + +/* + * select serial console configuration + */ +#define CONFIG_SERIAL1 1 /* UART1 on H4 */ + + /* + * I2C configuration + */ +#define CONFIG_HARD_I2C +#define CFG_I2C_SPEED 100000 +#define CFG_I2C_SLAVE 1 +#define CONFIG_DRIVER_OMAP24XX_I2C + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_ONENAND + +#undef CONFIG_CMD_AUTOSCRIPT + +#ifndef CFG_USE_NOR +# undef CONFIG_CMD_FLASH +# undef CONFIG_CMD_IMLS +#endif + +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT + +#define CONFIG_BOOTDELAY 1 + +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_IPADDR 192.168.116.25 +#define CONFIG_SERVERIP 192.168.116.1 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_ETHADDR 00:0E:99:00:24:20 + +#ifdef CONFIG_APOLLON_PLUS +# define CONFIG_BOOTARGS "root=/dev/nfs rw mem=64M console=ttyS0,115200n8 ip=192.168.116.25:192.168.116.1:192.168.116.1:255.255.255.0:apollon:eth0:off nfsroot=/tftpboot/nfsroot profile=2" +#else +# define CONFIG_BOOTARGS "root=/dev/nfs rw mem=128M console=ttyS0,115200n8 ip=192.168.116.25:192.168.116.1:192.168.116.1:255.255.255.0:apollon:eth0:off nfsroot=/tftpboot/nfsroot profile=2" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "Image=tftp 0x80008000 Image\; go 0x80008000\0" \ + "zImage=tftp 0x80180000 zImage\; go 0x80180000\0" \ + "uImage=tftp 0x80180000 uImage\; bootm 0x80180000\0" \ + "uboot=tftp 0x80008000 u-boot.bin\; go 0x80008000\0" \ + "xloader=tftp 0x80180000 x-load.bin\; cp.w 0x80180000 0x00000400 0x1000\; go 0x00000400\0" \ + "syncmode50=mw.w 0x1e442 0xc0c4\; mw 0x6800a060 0xe30d1201\0" \ + "syncmode=mw.w 0x1e442 0xe0f4\; mw 0x6800a060 0xe30d1201\0" \ + "norboot=cp32 0x18040000 0x80008000 0x200000\; go 0x80008000\0" \ + "oneboot=onenand read 0x80008000 0x40000 0x200000\; go 0x80008000\0"\ + "onesyncboot=run syncmode oneboot\0" \ + "bootcmd=run uboot\0" + +/* + * Miscellaneous configurable options + */ +#define V_PROMPT "Apollon # " + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT V_PROMPT +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START (OMAP2420_SDRC_CS0) /* memtest works on */ +#define CFG_MEMTEST_END (OMAP2420_SDRC_CS0+SZ_31M) + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */ + +/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) + * or by 32KHz clk, or from external sig. This rate is divided by a local + * divisor. + */ +#define V_PVT 7 /* use with 12MHz/128 */ + +#define CFG_TIMERBASE OMAP2420_GPT2 +#define CFG_PVT V_PVT /* 2^(pvt+1) */ +#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT)) + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE SZ_128K /* regular stack */ +#ifdef CONFIG_USE_IRQ +# define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */ +# define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* CS1 may or may not be populated */ +#define PHYS_SDRAM_1 OMAP2420_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE SZ_128M +#define PHYS_SDRAM_2 OMAP2420_SDRC_CS1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#ifdef CFG_USE_NOR +/* OneNAND boot, NOR has CS3, But NOR has CS0 when NOR boot */ +# define CFG_FLASH_BASE 0x18000000 +# define CFG_MAX_FLASH_BANKS 1 +# define CFG_MAX_FLASH_SECT 1024 +/*----------------------------------------------------------------------- + + * CFI FLASH driver setup + */ +# define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ +# define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +//#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ +# define CFG_FLASH_PROTECTION 1 /* Use h/w sector protection*/ + +#else /* !CFG_USE_NOR */ +# define CFG_NO_FLASH 1 +#endif /* CFG_USE_NOR */ + +/* OneNAND boot, OneNAND has CS0, NOR boot ONeNAND has CS2 */ +#define CFG_ONENAND_BASE 0x00000000 +#define CFG_ENV_IS_IN_ONENAND 1 +#define CFG_ENV_ADDR 0x00020000 + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 2d14684341109a69616e4d6016cd61402d55086f Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 9 Nov 2007 15:37:53 +0100 Subject: ppc4xx: Use generic usb-ohci driver for sequoia board This patch makes the sequoia board use the generic usb-ohci driver instead of cpu/ppc4xx/usb_ohci.c. Signed-off-by: Matthias Fuchs Signed-off-by: Stefan Roese --- include/configs/sequoia.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 72f01d90fd2..2af675ae146 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -301,8 +301,15 @@ /* USB */ #ifdef CONFIG_440EPX -#define CONFIG_USB_OHCI +#define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE +#define CFG_OHCI_BE_CONTROLLER + +#undef CFG_USB_OHCI_BOARD_INIT +#define CFG_USB_OHCI_CPU_INIT 1 +#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST +#define CFG_USB_OHCI_SLOT_NAME "ppc440" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE -- cgit v1.3.1 From 1d8a49eca1c7bdc8db1c47a92f9014a29ead03ae Mon Sep 17 00:00:00 2001 From: Roy Zang Date: Thu, 13 Sep 2007 18:52:28 +0800 Subject: Enable ULi1575 Ethernet support in 8610HPCD config Signed-off-by: Roy Zang Acked-by: Jon Loeliger --- include/configs/MPC8610HPCD.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index f5d9c098c6b..ef1310f606b 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -312,16 +312,16 @@ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CONFIG_NET_MULTI +#define CONFIG_CMD_NET #define CONFIG_PCI_PNP /* do pci plug-and-play */ -#if 0 /* TODO */ -/* enable onboard uli network support */ -#endif - #define CONFIG_RTL8139 #define CONFIG_SK98 #define CONFIG_EEPRO100 #define CONFIG_TULIP +#ifdef CONFIG_TULIP +#define CONFIG_ETHADDR 00:E0:0C:00:00:01 +#endif /************************************************************ * USB support -- cgit v1.3.1 From 2db916e14410e3ec1738508c7bf4dfeb2b299ae7 Mon Sep 17 00:00:00 2001 From: Peter Pearse Date: Thu, 15 Nov 2007 08:45:13 +0000 Subject: Correction patch --- board/apollon/apollon.c | 468 +++++++++++++------------------------ board/apollon/lowlevel_init.S | 18 +- board/apollon/mem.c | 43 ++-- board/apollon/mem.h | 16 +- board/apollon/sys_info.c | 31 ++- board/apollon/u-boot.lds | 3 +- include/asm-arm/arch-arm1136/mux.h | 18 +- 7 files changed, 239 insertions(+), 358 deletions(-) (limited to 'include') diff --git a/board/apollon/apollon.c b/board/apollon/apollon.c index e2c62772575..064d143ae48 100644 --- a/board/apollon/apollon.c +++ b/board/apollon/apollon.c @@ -31,18 +31,32 @@ #include #include #include -#include #include void wait_for_command_complete(unsigned int wd_base); +DECLARE_GLOBAL_DATA_PTR; + +#define write_config_reg(reg, value) \ +do { \ + writeb(value, reg); \ +} while (0) + +#define mask_config_reg(reg, mask) \ +do { \ + char value = readb(reg) & ~(mask); \ + writeb(value, reg); \ +} while (0) + /******************************************************* * Routine: delay * Description: spinning delay to use before udelay works -******************************************************/ -static inline void delay(unsigned long loops) { - __asm__ volatile ("1:\n" "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0"(loops)); } + ******************************************************/ +static inline void delay(unsigned long loops) +{ + __asm__("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); +} /***************************************** * Routine: board_init @@ -50,8 +64,6 @@ static inline void delay(unsigned long loops) { *****************************************/ int board_init(void) { - DECLARE_GLOBAL_DATA_PTR; - gpmc_init(); /* in SRAM or SDRM, finish GPMC */ gd->bd->bi_arch_number = 919; @@ -68,7 +80,6 @@ int board_init(void) **********************************************************/ void s_init(void) { - watchdog_init(); set_muxconf_regs(); delay(100); @@ -80,7 +91,7 @@ void s_init(void) /******************************************************* * Routine: misc_init_r * Description: Init ethernet (done here so udelay works) -********************************************************/ + ********************************************************/ int misc_init_r(void) { ether_init(); /* better done here so timers are init'ed */ @@ -102,22 +113,24 @@ void watchdog_init(void) __raw_writel(WD_UNLOCK2, WD2_BASE + WSPR); #define MPU_WD_CLOCKED 1 -#if MPU_WD_CLOCKED /* value 0x10 stick on aptix, BIT4 polarity seems oppsite */ +#if MPU_WD_CLOCKED + /* value 0x10 stick on aptix, BIT4 polarity seems oppsite */ __raw_writel(WD_UNLOCK1, WD3_BASE + WSPR); wait_for_command_complete(WD3_BASE); __raw_writel(WD_UNLOCK2, WD3_BASE + WSPR); __raw_writel(WD_UNLOCK1, WD4_BASE + WSPR); wait_for_command_complete(WD4_BASE); - __raw_writel(WD_UNLOCK2, WD4_BASE + WSPR); -#endif + __raw_writel(WD_UNLOCK2, WD4_BASE + WSPR); +#endif } /****************************************************** * Routine: wait_for_command_complete * Description: Wait for posting to finish on watchdog -******************************************************/ -void wait_for_command_complete(unsigned int wd_base) { + ******************************************************/ +void wait_for_command_complete(unsigned int wd_base) +{ int pending = 1; do { pending = __raw_readl(wd_base + WWPS); @@ -160,7 +173,7 @@ void ether_init(void) } while (__raw_readw(LAN_RESET_REGISTER) != 0x0000); udelay(1000); - *((volatile unsigned char *)ETH_CONTROL_REG) &= ~0x01; + mask_config_reg(ETH_CONTROL_REG, 0x01); udelay(1000); eth_reset_err_out: @@ -171,10 +184,9 @@ eth_reset_err_out: /********************************************** * Routine: dram_init * Description: sets uboots idea of sdram size -**********************************************/ + **********************************************/ int dram_init(void) { - DECLARE_GLOBAL_DATA_PTR; unsigned int size0 = 0, size1 = 0; u32 mtype, btype, rev = 0, cpu = 0; #define NOT_EARLY 0 @@ -187,8 +199,8 @@ int dram_init(void) display_board_info(btype); if ((mtype == DDR_COMBO) || (mtype == DDR_STACKED)) { - printf("ddr combo\n"); - do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); /* init other chip select */ + /* init other chip select */ + do_sdrc_init(SDRC_CS1_OSET, NOT_EARLY); } size0 = get_sdr_cs_size(SDRC_CS0_OSET); @@ -224,7 +236,7 @@ void set_muxconf_regs(void) /***************************************************************** * Routine: peripheral_enable * Description: Enable the clks & power for perifs (GPT2, UART1,...) -******************************************************************/ + ******************************************************************/ void peripheral_enable(void) { unsigned int v, if_clks = 0, func_clks = 0; @@ -232,7 +244,8 @@ void peripheral_enable(void) /* Enable GP2 timer. */ if_clks |= BIT4 | BIT3; func_clks |= BIT4 | BIT3; - v = __raw_readl(CM_CLKSEL2_CORE) | 0x4 | 0x2; /* Sys_clk input OMAP2420_GPT2 */ + /* Sys_clk input OMAP2420_GPT2 */ + v = __raw_readl(CM_CLKSEL2_CORE) | 0x4 | 0x2; __raw_writel(v, CM_CLKSEL2_CORE); __raw_writel(0x1, CM_CLKSEL_WKUP); @@ -241,9 +254,11 @@ void peripheral_enable(void) func_clks |= BIT21; if_clks |= BIT21; #endif - v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; /* Interface clocks on */ + /* Interface clocks on */ + v = __raw_readl(CM_ICLKEN1_CORE) | if_clks; __raw_writel(v, CM_ICLKEN1_CORE); - v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; /* Functional Clocks on */ + /* Functional Clocks on */ + v = __raw_readl(CM_FCLKEN1_CORE) | func_clks; __raw_writel(v, CM_FCLKEN1_CORE); delay(1000); @@ -261,199 +276,110 @@ void peripheral_enable(void) } /**************************************** - * Routine: muxSetupUsb0 (ostboot) + * Routine: muxSetupUsb0 (ostboot) * Description: Setup usb muxing *****************************************/ void muxSetupUsb0(void) { - volatile uint8 *MuxConfigReg; - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_PUEN; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VP; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_VM; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_RCV; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_TXEN; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_SE0; - *MuxConfigReg &= (uint8) (~0x1F); - - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB0_DAT; - *MuxConfigReg &= (uint8) (~0x1F); + mask_config_reg(CONTROL_PADCONF_USB0_PUEN, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_VP, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_VM, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_RCV, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_TXEN, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_SE0, 0x1f); + mask_config_reg(CONTROL_PADCONF_USB0_DAT, 0x1f); } -#define CONTROL_PADCONF_USB1_RCV ((volatile uint8 *)0x480000EB) -#define CONTROL_PADCONF_USB1_TXEN ((volatile uint8 *)0x480000EC) -#define CONTROL_PADCONF_GPIO69 ((volatile uint8 *)0x480000ED) -#define CONTROL_PADCONF_GPIO70 ((volatile uint8 *)0x480000EE) - -#define CONTROL_PADCONF_GPIO102 ((volatile uint8 *)0x48000116) -#define CONTROL_PADCONF_GPIO103 ((volatile uint8 *)0x48000117) -#define CONTROL_PADCONF_GPIO104 ((volatile uint8 *)0x48000118) -#define CONTROL_PADCONF_GPIO105 ((volatile uint8 *)0x48000119) /**************************************** - * Routine: muxSetupUSBHost (ostboot) + * Routine: muxSetupUSBHost (ostboot) * Description: Setup USB Host muxing *****************************************/ void muxSetupUsbHost(void) { - volatile uint8 *MuxConfigReg; - /* V19 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB1_RCV; - *MuxConfigReg = 1; + write_config_reg(CONTROL_PADCONF_USB1_RCV, 1); /* W20 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_USB1_TXEN; - *MuxConfigReg = 1; + write_config_reg(CONTROL_PADCONF_USB1_TXEN, 1); /* N14 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO69; - *MuxConfigReg = 3; + write_config_reg(CONTROL_PADCONF_GPIO69, 3); /* P15 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO70; - *MuxConfigReg = 3; - + write_config_reg(CONTROL_PADCONF_GPIO70, 3); /* L18 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO102; - *MuxConfigReg = 3; + write_config_reg(CONTROL_PADCONF_GPIO102, 3); /* L19 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO103; - *MuxConfigReg = 3; + write_config_reg(CONTROL_PADCONF_GPIO103, 3); /* K15 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO104; - *MuxConfigReg = 3; + write_config_reg(CONTROL_PADCONF_GPIO104, 3); /* K14 */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPIO105; - *MuxConfigReg = 3; + write_config_reg(CONTROL_PADCONF_GPIO105, 3); } /**************************************** - * Routine: muxSetupUART1 (ostboot) + * Routine: muxSetupUART1 (ostboot) * Description: Set up uart1 muxing *****************************************/ void muxSetupUART1(void) { - volatile unsigned char *MuxConfigReg; - - /* UART1_CTS pin configuration, PIN = D21 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_CTS; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* UART1_RTS pin configuration, PIN = H21 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RTS; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* UART1_TX pin configuration, PIN = L20 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_TX; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* UART1_RX pin configuration, PIN = T21 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_UART1_RX; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* UART1_CTS pin configuration, PIN = D21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_CTS, 0); + /* UART1_RTS pin configuration, PIN = H21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_RTS, 0); + /* UART1_TX pin configuration, PIN = L20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_TX, 0); + /* UART1_RX pin configuration, PIN = T21, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_UART1_RX, 0); } /**************************************** - * Routine: muxSetupLCD (ostboot) + * Routine: muxSetupLCD (ostboot) * Description: Setup lcd muxing *****************************************/ void muxSetupLCD(void) { - volatile unsigned char *MuxConfigReg; - - /* LCD_D0 pin configuration, PIN = Y7 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D0; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D1 pin configuration, PIN = P10 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D1; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D2 pin configuration, PIN = V8 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D2; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D3 pin configuration, PIN = Y8 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D3; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D4 pin configuration, PIN = W8 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D4; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D5 pin configuration, PIN = R10 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D5; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D6 pin configuration, PIN = Y9 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D6; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D7 pin configuration, PIN = V9 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D7; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D8 pin configuration, PIN = W9 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D8; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D9 pin configuration, PIN = P11 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D9; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D10 pin configuration, PIN = V10 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D10; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D11 pin configuration, PIN = Y10 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D11; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D12 pin configuration, PIN = W10 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D12; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D13 pin configuration, PIN = R11 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D13; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D14 pin configuration, PIN = V11 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D14; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D15 pin configuration, PIN = W11 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D15; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D16 pin configuration, PIN = P12 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D16; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_D17 pin configuration, PIN = R12 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_D17; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_PCLK pin configuration, PIN = W6 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_PCLK; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_VSYNC pin configuration, PIN = V7 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_VSYNC; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_HSYNC pin configuration, PIN = Y6 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_HSYNC; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* LCD_ACBIAS pin configuration, PIN = W7 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_DSS_ACBIAS; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* LCD_D0 pin configuration, PIN = Y7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D0, 0); + /* LCD_D1 pin configuration, PIN = P10 , Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D1, 0); + /* LCD_D2 pin configuration, PIN = V8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D2, 0); + /* LCD_D3 pin configuration, PIN = Y8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D3, 0); + /* LCD_D4 pin configuration, PIN = W8, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D4, 0); + /* LCD_D5 pin configuration, PIN = R10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D5, 0); + /* LCD_D6 pin configuration, PIN = Y9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D6, 0); + /* LCD_D7 pin configuration, PIN = V9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D7, 0); + /* LCD_D8 pin configuration, PIN = W9, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D8, 0); + /* LCD_D9 pin configuration, PIN = P11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D9, 0); + /* LCD_D10 pin configuration, PIN = V10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D10, 0); + /* LCD_D11 pin configuration, PIN = Y10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D11, 0); + /* LCD_D12 pin configuration, PIN = W10, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D12, 0); + /* LCD_D13 pin configuration, PIN = R11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D13, 0); + /* LCD_D14 pin configuration, PIN = V11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D14, 0); + /* LCD_D15 pin configuration, PIN = W11, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D15, 0); + /* LCD_D16 pin configuration, PIN = P12, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D16, 0); + /* LCD_D17 pin configuration, PIN = R12, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_D17, 0); + /* LCD_PCLK pin configuration, PIN = W6, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_PCLK, 0); + /* LCD_VSYNC pin configuration, PIN = V7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_VSYNC, 0); + /* LCD_HSYNC pin configuration, PIN = Y6, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_HSYNC, 0); + /* LCD_ACBIAS pin configuration, PIN = W7, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_DSS_ACBIAS, 0); } /**************************************** @@ -462,146 +388,84 @@ void muxSetupLCD(void) *****************************************/ void muxSetupMMCSD(void) { - volatile unsigned char *MuxConfigReg; - - /* SDMMC_CLKI pin configuration, PIN = H15 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKI; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_CLKO pin configuration, PIN = G19 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CLKO; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_CMD pin configuration, PIN = H18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - /* External pull-ups are present. */ - /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ - - /* SDMMC_DAT0 pin configuration, PIN = F20 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT0; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - /* External pull-ups are present. */ - /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ - - /* SDMMC_DAT1 pin configuration, PIN = H14 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT1; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - /* External pull-ups are present. */ - /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ - - /* SDMMC_DAT2 pin configuration, PIN = E19 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT2; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - /* External pull-ups are present. */ - /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ - - /* SDMMC_DAT3 pin configuration, PIN = D19 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT3; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - /* External pull-ups are present. */ - /* *MuxConfigReg |= 0x18 ; #/ PullUDEnable=Enabled, PullTypeSel=PU */ - - /* SDMMC_DDIR0 pin configuration, PIN = F19 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR0; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_DDIR1 pin configuration, PIN = E20 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR1; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_DDIR2 pin configuration, PIN = F18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR2; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_DDIR3 pin configuration, PIN = E18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_DAT_DIR3; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SDMMC_CDIR pin configuration, PIN = G18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_MMC_CMD_DIR; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ + /* SDMMC_CLKI pin configuration, PIN = H15, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CLKI, 0); + /* SDMMC_CLKO pin configuration, PIN = G19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CLKO, 0); + /* SDMMC_CMD pin configuration, PIN = H18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CMD, 0); + /* SDMMC_DAT0 pin configuration, PIN = F20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT0, 0); + /* SDMMC_DAT1 pin configuration, PIN = H14, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT1, 0); + /* SDMMC_DAT2 pin configuration, PIN = E19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT2, 0); + /* SDMMC_DAT3 pin configuration, PIN = D19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT3, 0); + /* SDMMC_DDIR0 pin configuration, PIN = F19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR0, 0); + /* SDMMC_DDIR1 pin configuration, PIN = E20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR1, 0); + /* SDMMC_DDIR2 pin configuration, PIN = F18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR2, 0); + /* SDMMC_DDIR3 pin configuration, PIN = E18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_DAT_DIR3, 0); + /* SDMMC_CDIR pin configuration, PIN = G18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_MMC_CMD_DIR, 0); } /****************************************** * Routine: muxSetupTouchScreen (ostboot) - * Description: Set up touch screen muxing -*******************************************/ + * Description: Set up touch screen muxing + *******************************************/ void muxSetupTouchScreen(void) { - volatile unsigned char *MuxConfigReg; - - /* SPI1_CLK pin configuration, PIN = U18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_CLK; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SPI1_MOSI pin configuration, PIN = V20 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SIMO; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SPI1_MISO pin configuration, PIN = T18 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_SOMI; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - - /* SPI1_nCS0 pin configuration, PIN = U19 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_SPI1_NCS0; - *MuxConfigReg = 0x00; /* Mode = 0, PUPD=Disabled */ - + /* SPI1_CLK pin configuration, PIN = U18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_CLK, 0); + /* SPI1_MOSI pin configuration, PIN = V20, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_SIMO, 0); + /* SPI1_MISO pin configuration, PIN = T18, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_SOMI, 0); + /* SPI1_nCS0 pin configuration, PIN = U19, Mode = 0, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_SPI1_NCS0, 0); #define CONTROL_PADCONF_GPIO85 CONTROL_PADCONF_SPI1_NCS1 - - /* PEN_IRQ pin configuration, PIN = N15 */ - MuxConfigReg = (volatile unsigned char *)CONTROL_PADCONF_GPIO85; - *MuxConfigReg = 0x03; /* Mode = 3, PUPD=Disabled */ + /* PEN_IRQ pin configuration, PIN = N15, Mode = 3, PUPD=Disabled */ + write_config_reg(CONTROL_PADCONF_GPIO85, 3); } /*************************************************************** * Routine: muxSetupGPMC (ostboot) * Description: Configures balls which cam up in protected mode -***************************************************************/ + ***************************************************************/ void muxSetupGPMC(void) { - volatile uint8 *MuxConfigReg; - volatile unsigned int *MCR = (volatile unsigned int *)0x4800008C; - - /* gpmc_io_dir */ - *MCR = 0x19000000; + /* gpmc_io_dir, MCR */ + writel(0x4800008C, 0x19000000); /* NOR FLASH CS0 */ - /* signal - Gpmc_clk; - pin - J4; offset - 0x0088; mode - 0; Byte-3 Pull/up - N/A */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_D2_BYTE3; - *MuxConfigReg = 0x00; - + /* signal - Gpmc_clk; pin - J4; offset - 0x0088; mode 0; Byte-3 */ + write_config_reg(CONTROL_PADCONF_GPMC_D2_BYTE3, 0); /* MPDB(Multi Port Debug Port) CS1 */ - /* signal - gpmc_ncs1; - pin - N8; offset - 0x008C; mode - 0; Byte-1 Pull/up - N/A */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE1; - *MuxConfigReg = 0x00; - - /* signal - Gpmc_ncs2; - pin - E2; offset - 0x008C; mode - 0; Byte-2 Pull/up - N/A */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE2; - *MuxConfigReg = 0x00; - - /* signal - Gpmc_ncs3; - pin - N2; offset - 0x008C; mode - 0; Byte-3 Pull/up - N/A */ - MuxConfigReg = (volatile uint8 *)CONTROL_PADCONF_GPMC_NCS0_BYTE3; - *MuxConfigReg = 0x00; - - MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000090); - *MuxConfigReg = 0x00; - MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000091); - *MuxConfigReg = 0x00; - MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000092); - *MuxConfigReg = 0x00; - MuxConfigReg = (volatile uint8 *)((volatile unsigned char *)0x48000093); - *MuxConfigReg = 0x00; + /* signal - gpmc_ncs1; pin - N8; offset - 0x008D; mode 0; Byte-1 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE1, 0); + /* signal - Gpmc_ncs2; pin - E2; offset - 0x008E; mode 0; Byte-2 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE2, 0); + /* signal - Gpmc_ncs3; pin - N2; offset - 0x008F; mode 0; Byte-3 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE3, 0); + /* signal - Gpmc_ncs4; pin - ??; offset - 0x0090; mode 0; Byte-4 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE4, 0); + /* signal - Gpmc_ncs5; pin - ??; offset - 0x0091; mode 0; Byte-5 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE5, 0); + /* signal - Gpmc_ncs6; pin - ??; offset - 0x0092; mode 0; Byte-6 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE6, 0); + /* signal - Gpmc_ncs7; pin - ??; offset - 0x0093; mode 0; Byte-7 */ + write_config_reg(CONTROL_PADCONF_GPMC_NCS0_BYTE7, 0); } /**************************************************************** - * Routine: muxSetupSDRC (ostboot) + * Routine: muxSetupSDRC (ostboot) * Description: Configures balls which come up in protected mode -****************************************************************/ + ****************************************************************/ void muxSetupSDRC(void) { /* It's set by IPL */ diff --git a/board/apollon/lowlevel_init.S b/board/apollon/lowlevel_init.S index 76762599b1d..f254428c9ca 100644 --- a/board/apollon/lowlevel_init.S +++ b/board/apollon/lowlevel_init.S @@ -34,13 +34,13 @@ #define APOLLON_CS0_BASE 0x00000000 #ifdef PRCM_CONFIG_I -# define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 -# define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 -# define SDRC_RFR_CTRL_0_VAL 0x00044C01 +#define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 +#define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 +#define SDRC_RFR_CTRL_0_VAL 0x00044C01 #elif defined(PRCM_CONFIG_II) -# define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 -# define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C -# define SDRC_RFR_CTRL_0_VAL 0x00030001 +#define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 +#define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C +#define SDRC_RFR_CTRL_0_VAL 0x00030001 #endif #define SDRAM_BASE_ADDRESS 0x80008000 @@ -56,7 +56,7 @@ lowlevel_init: mov r0, pc, lsr #28 cmp r0, #8 beq prcm_setup - + flash_setup: /* In Flash */ ldr r0, =WD2_BASE @@ -203,7 +203,7 @@ prcm_setup: ldr r1, =0x00000002 str r1, [r0, #0x340] - + ldr r1, =CM_CLKSEL1_CORE #ifdef PRCM_CONFIG_I ldr r2, =0x08300C44 @@ -211,7 +211,7 @@ prcm_setup: ldr r2, =0x04600C26 #endif str r2, [r1] - + ldr r0, =OMAP2420_CM_BASE ldr r1, [r0, #0x084] and r1, r1, #0x01 diff --git a/board/apollon/mem.c b/board/apollon/mem.c index 8154d118120..c0edca56e19 100644 --- a/board/apollon/mem.c +++ b/board/apollon/mem.c @@ -39,20 +39,19 @@ * is necessary until timers are accessible. * * not inline to increase chances its in cache when called -*************************************************************/ + *************************************************************/ void sdelay(unsigned long loops) { - __asm__ volatile ("1:\n" "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0"(loops)); + __asm__("1:\n" "subs %0, %1, #1\n" + "bne 1b":"=r" (loops):"0"(loops)); } -/***************************************************************************** +/******************************************************************** * prcm_init() - inits clocks for PRCM as defined in clocks.h - * (config II default). Called from SRAM, or Flash (using temp SRAM stack). - *****************************************************************************/ -void prcm_init(void) -{ -} + * (config II default). + * -- called from SRAM, or Flash (using temp SRAM stack). + ********************************************************************/ +void prcm_init(void) { } /************************************************************************** * make_cs1_contiguous() - for es2 and above remap cs1 behind cs0 to allow @@ -69,6 +68,7 @@ void make_cs1_contiguous(void) a_add_high = (size & 3) << 8; /* set up low field */ a_add_low = (size & 0x3C) >> 2; /* set up high field */ __raw_writel((a_add_high | a_add_low), SDRC_CS_CFG); + } /******************************************************** @@ -81,13 +81,18 @@ u32 mem_ok(void) u32 val1, val2; u32 pattern = 0x12345678; - __raw_writel(0x0, OMAP2420_SDRC_CS0 + 0x400); /* clear pos A */ - __raw_writel(pattern, OMAP2420_SDRC_CS0); /* pattern to pos B */ - __raw_writel(0x0, OMAP2420_SDRC_CS0 + 4); /* remove pattern off the bus */ - val1 = __raw_readl(OMAP2420_SDRC_CS0 + 0x400); /* get pos A value */ + /* clear pos A */ + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 0x400); + /* pattern to pos B */ + __raw_writel(pattern, OMAP2420_SDRC_CS0); + /* remove pattern off the bus */ + __raw_writel(0x0, OMAP2420_SDRC_CS0 + 4); + /* get pos A value */ + val1 = __raw_readl(OMAP2420_SDRC_CS0 + 0x400); val2 = __raw_readl(OMAP2420_SDRC_CS0); /* get val2 */ - if ((val1 != 0) || (val2 != pattern)) /* see if pos A value changed */ + /* see if pos A value changed */ + if ((val1 != 0) || (val2 != pattern)) return (0); else return (1); @@ -142,9 +147,11 @@ void gpmc_init(void) __raw_writel(0x0, GPMC_IRQENABLE); /* isr's sources masked */ __raw_writel(tval, GPMC_TIMEOUT_CONTROL); /* timeout disable */ #ifdef CFG_NAND_BOOT - __raw_writel(0x001, GPMC_CONFIG); /* set nWP, disable limited addr */ + /* set nWP, disable limited addr */ + __raw_writel(0x001, GPMC_CONFIG); #else - __raw_writel(0x111, GPMC_CONFIG); /* set nWP, disable limited addr */ + /* set nWP, disable limited addr */ + __raw_writel(0x111, GPMC_CONFIG); #endif /* discover bus connection from sysboot */ @@ -164,7 +171,8 @@ void gpmc_init(void) __raw_writel(APOLLON_24XX_GPMC_CONFIG4_3, GPMC_CONFIG4_0); __raw_writel(APOLLON_24XX_GPMC_CONFIG5_3, GPMC_CONFIG5_0); __raw_writel(APOLLON_24XX_GPMC_CONFIG6_3, GPMC_CONFIG6_0); - __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_0); #else + __raw_writel(APOLLON_24XX_GPMC_CONFIG7_3, GPMC_CONFIG7_0); +#else __raw_writel(APOLLON_24XX_GPMC_CONFIG1_0 | mux | mtype | mwidth, GPMC_CONFIG1_0); __raw_writel(APOLLON_24XX_GPMC_CONFIG2_0, GPMC_CONFIG2_0); @@ -172,7 +180,6 @@ void gpmc_init(void) __raw_writel(APOLLON_24XX_GPMC_CONFIG4_0, GPMC_CONFIG4_0); __raw_writel(APOLLON_24XX_GPMC_CONFIG5_0, GPMC_CONFIG5_0); __raw_writel(APOLLON_24XX_GPMC_CONFIG6_0, GPMC_CONFIG6_0); - /* enable new mapping */ __raw_writel(APOLLON_24XX_GPMC_CONFIG7_0, GPMC_CONFIG7_0); #endif sdelay(2000); diff --git a/board/apollon/mem.h b/board/apollon/mem.h index aed7e1d64d2..5bc96faa957 100644 --- a/board/apollon/mem.h +++ b/board/apollon/mem.h @@ -44,15 +44,15 @@ #define APOLLON_242x_SDRC_DLLAB_CTRL_166MHz 0x00000506 #ifdef PRCM_CONFIG_I -# define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz -# define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz -# define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_166MHz -# define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_166MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_166MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_166MHz +#define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_166MHz +#define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_166MHz #elif PRCM_CONFIG_II -# define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz -# define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz -# define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_100MHz -# define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_100MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLA_0 APOLLON_242X_SDRC_ACTIM_CTRLA_0_100MHz +#define APOLLON_2420_SDRC_ACTIM_CTRLB_0 APOLLON_242X_SDRC_ACTIM_CTRLB_0_100MHz +#define APOLLON_2420_SDRC_RFR_CTRL APOLLON_242X_SDRC_RFR_CTRL_100MHz +#define APOLLON_2420_SDRC_DLLAB_CTRL APOLLON_242x_SDRC_DLLAB_CTRL_100MHz #endif /* GPMC settings */ diff --git a/board/apollon/sys_info.c b/board/apollon/sys_info.c index 60c35b4586b..26ac9a2c8d0 100644 --- a/board/apollon/sys_info.c +++ b/board/apollon/sys_info.c @@ -39,6 +39,7 @@ static u32 get_prod_id(void) p = __raw_readl(PRODUCTION_ID); /* get production ID */ return ((p & CPU_242X_PID_MASK) >> 16); } + /************************************************************************** * get_cpu_type() - low level get cpu type * - no C globals yet. @@ -68,7 +69,8 @@ u32 get_cpu_type(void) v = __raw_readl(TAP_IDCODE_REG); v &= CPU_24XX_ID_MASK; - if (v == CPU_2420_CHIPID) { /* currently 2420 and 2422 have same id */ + /* currently 2420 and 2422 have same id */ + if (v == CPU_2420_CHIPID) { if (is_gpmc_muxed() == GPMC_MUXED) /* if mux'ed */ return (CPU_2420); else @@ -127,8 +129,7 @@ u32 get_mem_type(void) return (DDR_DISCRETE); /* origional SDP */ } -/********************************************************************** - * +/*********************************************************************** * get_cs0_size() - get size of chip select 0/1 ************************************************************************/ u32 get_sdr_cs_size(u32 offset) @@ -140,8 +141,7 @@ u32 get_sdr_cs_size(u32 offset) return (size); } -/********************************************************************** - * +/*********************************************************************** * get_board_type() - get board type based on current production stats. * --- NOTE: 2 I2C EEPROMs will someday be populated with proper info. * when they are available we can get info from there. This should @@ -149,17 +149,12 @@ u32 get_sdr_cs_size(u32 offset) ************************************************************************/ u32 get_board_type(void) { -#if 0 - if (i2c_probe(I2C_MENELAUS) == 0) - return (BOARD_H4_MENELAUS); - else -#endif - return (BOARD_H4_SDP); + return (BOARD_H4_SDP); } /****************************************************************** * get_sysboot_value() - get init word settings (dip switch on h4) -******************************************************************/ + ******************************************************************/ inline u32 get_sysboot_value(void) { return (0x00000FFF & __raw_readl(CONTROL_STATUS)); @@ -175,7 +170,7 @@ inline u32 get_sysboot_value(void) * -- 4 to flash * -- 8 to enent * -- c to wifi - ***************************************************************************/ + ****************************************************************************/ u32 get_gpmc0_base(void) { u32 b; @@ -231,8 +226,8 @@ u32 get_gpmc0_width(void) * wait_on_value() - common routine to allow waiting for changes in * volatile regs. *********************************************************************/ -u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, -u32 bound) { +u32 wait_on_value(u32 read_bit_mask, u32 match_value, u32 read_addr, u32 bound) +{ u32 i = 0, val; do { ++i; @@ -304,7 +299,8 @@ void display_board_info(u32 btype) } printf("OMAP%s-%s revision %d\n", cpu_s, sec_s, rev - 1); - printf("Samsung Apollon SDP Base Board + %s \n", mem_s); } + printf("Samsung Apollon SDP Base Board + %s \n", mem_s); +} /************************************************************************* * get_board_rev() - setup to pass kernel board revision information @@ -316,9 +312,8 @@ u32 get_board_rev(void) u32 rev = 0; u32 btype = get_board_type(); - if (btype == BOARD_H4_MENELAUS) { + if (btype == BOARD_H4_MENELAUS) rev = 1; - } return (rev); } diff --git a/board/apollon/u-boot.lds b/board/apollon/u-boot.lds index 686d86b76ed..c67cd3cda7f 100644 --- a/board/apollon/u-boot.lds +++ b/board/apollon/u-boot.lds @@ -36,7 +36,7 @@ SECTIONS . = 0x00000000; . = ALIGN(4); - .text : + .text : { cpu/arm1136/start.o (.text) *(.text) @@ -61,4 +61,3 @@ SECTIONS .bss : { *(.bss) } _end = .; } - diff --git a/include/asm-arm/arch-arm1136/mux.h b/include/asm-arm/arch-arm1136/mux.h index 8bcd7a3685d..4fdb9c635fd 100644 --- a/include/asm-arm/arch-arm1136/mux.h +++ b/include/asm-arm/arch-arm1136/mux.h @@ -54,6 +54,10 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_GPMC_NCS0_BYTE1 ((volatile unsigned char *)0x4800008D) #define CONTROL_PADCONF_GPMC_NCS0_BYTE2 ((volatile unsigned char *)0x4800008E) #define CONTROL_PADCONF_GPMC_NCS0_BYTE3 ((volatile unsigned char *)0x4800008F) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE4 (0x48000090) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE5 (0x48000091) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE6 (0x48000092) +#define CONTROL_PADCONF_GPMC_NCS0_BYTE7 (0x48000093) /* Pin Muxing registers used for SDRC */ #define CONTROL_PADCONF_SDRC_NCS0_BYTE0 ((volatile unsigned char *)0x480000A0) @@ -71,7 +75,7 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_SPI1_SIMO ((volatile unsigned char *)0x48000100) #define CONTROL_PADCONF_SPI1_SOMI ((volatile unsigned char *)0x48000101) #define CONTROL_PADCONF_SPI1_NCS0 ((volatile unsigned char *)0x48000102) -#define CONTROL_PADCONF_SPI1_NCS1 ((volatile unsigned char *)0x48000103) +#define CONTROL_PADCONF_SPI1_NCS1 (0x48000103) #define CONTROL_PADCONF_MCBSP1_FSR ((volatile unsigned char *)0x4800010B) @@ -153,8 +157,20 @@ void muxSetupHDQ(void); #define CONTROL_PADCONF_USB0_SE0 ((volatile uint8 *)0x48000122) #define CONTROL_PADCONF_USB0_DAT ((volatile uint8 *)0x48000123) +/* Pin Muxing registres used for USB1. */ +#define CONTROL_PADCONF_USB1_RCV (0x480000EB) +#define CONTROL_PADCONF_USB1_TXEN (0x480000EC) + /* Pin Muxing registers used for UART3/IRDA */ #define CONTROL_PADCONF_UART3_TX_IRTX ((volatile uint8 *)0x48000118) #define CONTROL_PADCONF_UART3_RX_IRRX ((volatile uint8 *)0x48000119) +/* Pin Muxing registers used for GPIO */ +#define CONTROL_PADCONF_GPIO69 (0x480000ED) +#define CONTROL_PADCONF_GPIO70 (0x480000EE) +#define CONTROL_PADCONF_GPIO102 (0x48000116) +#define CONTROL_PADCONF_GPIO103 (0x48000117) +#define CONTROL_PADCONF_GPIO104 (0x48000118) +#define CONTROL_PADCONF_GPIO105 (0x48000119) + #endif -- cgit v1.3.1 From 2ae64f5135e51bb18753884d1265b99e89b5aedd Mon Sep 17 00:00:00 2001 From: Peter Pearse Date: Thu, 15 Nov 2007 08:58:00 +0000 Subject: Remove warnings re CONFIG_EXTRA_ENV_SETTINGS Remove warnings re onenand_read() & write() --- common/env_onenand.c | 4 ++-- include/configs/apollon.h | 18 +++++++++--------- 2 files changed, 11 insertions(+), 11 deletions(-) mode change 100644 => 100755 include/configs/apollon.h (limited to 'include') diff --git a/common/env_onenand.c b/common/env_onenand.c index 66107f91f17..5888f75d895 100644 --- a/common/env_onenand.c +++ b/common/env_onenand.c @@ -64,7 +64,7 @@ void env_relocate_spec(void) DECLARE_GLOBAL_DATA_PTR; unsigned long env_addr; int use_default = 0; - int retlen; + size_t retlen; env_addr = CFG_ENV_ADDR; env_addr -= (unsigned long)onenand_chip.base; @@ -96,7 +96,7 @@ int saveenv(void) { unsigned long env_addr = CFG_ENV_ADDR; struct erase_info instr; - int retlen; + size_t retlen; instr.len = CFG_ENV_SIZE; instr.addr = env_addr; diff --git a/include/configs/apollon.h b/include/configs/apollon.h old mode 100644 new mode 100755 index 578153c8bf9..7727bc3e291 --- a/include/configs/apollon.h +++ b/include/configs/apollon.h @@ -148,15 +148,15 @@ #endif #define CONFIG_EXTRA_ENV_SETTINGS \ - "Image=tftp 0x80008000 Image\; go 0x80008000\0" \ - "zImage=tftp 0x80180000 zImage\; go 0x80180000\0" \ - "uImage=tftp 0x80180000 uImage\; bootm 0x80180000\0" \ - "uboot=tftp 0x80008000 u-boot.bin\; go 0x80008000\0" \ - "xloader=tftp 0x80180000 x-load.bin\; cp.w 0x80180000 0x00000400 0x1000\; go 0x00000400\0" \ - "syncmode50=mw.w 0x1e442 0xc0c4\; mw 0x6800a060 0xe30d1201\0" \ - "syncmode=mw.w 0x1e442 0xe0f4\; mw 0x6800a060 0xe30d1201\0" \ - "norboot=cp32 0x18040000 0x80008000 0x200000\; go 0x80008000\0" \ - "oneboot=onenand read 0x80008000 0x40000 0x200000\; go 0x80008000\0"\ + "Image=tftp 0x80008000 Image; go 0x80008000\0" \ + "zImage=tftp 0x80180000 zImage; go 0x80180000\0" \ + "uImage=tftp 0x80180000 uImage; bootm 0x80180000\0" \ + "uboot=tftp 0x80008000 u-boot.bin; go 0x80008000\0" \ + "xloader=tftp 0x80180000 x-load.bin; cp.w 0x80180000 0x00000400 0x1000; go 0x00000400\0" \ + "syncmode50=mw.w 0x1e442 0xc0c4; mw 0x6800a060 0xe30d1201\0" \ + "syncmode=mw.w 0x1e442 0xe0f4; mw 0x6800a060 0xe30d1201\0" \ + "norboot=cp32 0x18040000 0x80008000 0x200000; go 0x80008000\0" \ + "oneboot=onenand read 0x80008000 0x40000 0x200000; go 0x80008000\0"\ "onesyncboot=run syncmode oneboot\0" \ "bootcmd=run uboot\0" -- cgit v1.3.1 From f23cb34c367bb27585a4fdb8a75277370e7d0596 Mon Sep 17 00:00:00 2001 From: Marian Balakowicz Date: Thu, 15 Nov 2007 13:24:43 +0100 Subject: [INKA4x0] NG hardware: platform code update - Cleanup compile warnings. - Add missing '\0' in default environment. - Increase CFG_MONITOR_LEN to 256 KiB. - Add required CFG_USE_PPCENV. Signed-off-by: Marian Balakowicz --- board/inka4x0/inka4x0.c | 8 ++++---- include/configs/inka4x0.h | 5 +++-- 2 files changed, 7 insertions(+), 6 deletions(-) (limited to 'include') diff --git a/board/inka4x0/inka4x0.c b/board/inka4x0/inka4x0.c index 478a331b408..c80fc3ba513 100644 --- a/board/inka4x0/inka4x0.c +++ b/board/inka4x0/inka4x0.c @@ -88,7 +88,7 @@ long int initdram (int board_type) { ulong dramsize = 0; #ifndef CFG_RAMBOOT - ulong test1, test2; + long test1, test2; /* setup SDRAM chip selects */ *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001c; /* 512MB at 0x0 */ @@ -108,9 +108,9 @@ long int initdram (int board_type) /* find RAM size using SDRAM CS0 only */ sdram_start(0); - test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x20000000); + test1 = get_ram_size((long *)CFG_SDRAM_BASE, 0x20000000); sdram_start(1); - test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x20000000); + test2 = get_ram_size((long *)CFG_SDRAM_BASE, 0x20000000); if (test1 > test2) { sdram_start(0); dramsize = test1; @@ -175,7 +175,7 @@ void flash_preinit(void) int misc_init_f (void) { - uchar tmp[10]; + char tmp[10]; int i, br; i = getenv_r("brightness", tmp, sizeof(tmp)); diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index 0fac28fadd7..af8fb21e276 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -142,7 +142,7 @@ "cp.l 100000 f0000b28 1\0" \ "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ "ide_boot=ext2load ide 0:1 200000 uImage;" \ - "run ideargs addip addcons enable_disp;bootm" \ + "run ideargs addip addcons enable_disp;bootm\0" \ "brightness=255\0" \ "" @@ -174,6 +174,7 @@ #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_OVERWRITE 1 +#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */ /* * Memory map @@ -203,7 +204,7 @@ # define CFG_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -- cgit v1.3.1 From 5fb6d7191e206cdde0e23140fd8111caed93a595 Mon Sep 17 00:00:00 2001 From: Marian Balakowicz Date: Thu, 15 Nov 2007 13:29:55 +0100 Subject: [INKA4x0] NG hardware: SDRAM support Add support for three new DDR chips that may be present on a NG INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT. Cleanup board/inka4x0/mt48lc16m16a2-75.h file. Signed-off-by: Marian Balakowicz --- board/inka4x0/hyb25d512160bf-5.h | 32 ++++++++++++++++++++++++++++++++ board/inka4x0/inka4x0.c | 12 ++++++++++-- board/inka4x0/k4h511638c.h | 32 ++++++++++++++++++++++++++++++++ board/inka4x0/mt46v16m16-75.h | 7 +------ board/inka4x0/mt46v32m16-75.h | 32 ++++++++++++++++++++++++++++++++ board/inka4x0/mt48lc16m16a2-75.h | 19 +------------------ include/configs/inka4x0.h | 9 ++++++++- 7 files changed, 116 insertions(+), 27 deletions(-) create mode 100644 board/inka4x0/hyb25d512160bf-5.h create mode 100644 board/inka4x0/k4h511638c.h create mode 100644 board/inka4x0/mt46v32m16-75.h (limited to 'include') diff --git a/board/inka4x0/hyb25d512160bf-5.h b/board/inka4x0/hyb25d512160bf-5.h new file mode 100644 index 00000000000..7eb1f50158f --- /dev/null +++ b/board/inka4x0/hyb25d512160bf-5.h @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2007 Semihalf + * Written by Marian Balakowicz + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#define SDRAM_DDR 1 /* is DDR */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714F0F00 +#define SDRAM_CONFIG1 0x73711930 +#define SDRAM_CONFIG2 0x46770000 +#define SDRAM_TAPDELAY 0x10000000 diff --git a/board/inka4x0/inka4x0.c b/board/inka4x0/inka4x0.c index c80fc3ba513..5157f7d81de 100644 --- a/board/inka4x0/inka4x0.c +++ b/board/inka4x0/inka4x0.c @@ -31,10 +31,18 @@ #include #include -#if defined(CONFIG_MPC5200_DDR) +#if defined(CONFIG_DDR_MT46V16M16) #include "mt46v16m16-75.h" -#else +#elif defined(CONFIG_SDR_MT48LC16M16A2) #include "mt48lc16m16a2-75.h" +#elif defined(CONFIG_DDR_MT46V32M16) +#include "mt46v32m16.h" +#elif defined(CONFIG_DDR_HYB25D512160BF) +#include "hyb25d512160bf.h" +#elif defined(CONFIG_DDR_K4H511638C) +#include "k4h511638c.h" +#else +#error "INKA4x0 SDRAM: invalid chip type specified!" #endif #ifndef CFG_RAMBOOT diff --git a/board/inka4x0/k4h511638c.h b/board/inka4x0/k4h511638c.h new file mode 100644 index 00000000000..70cc40521f4 --- /dev/null +++ b/board/inka4x0/k4h511638c.h @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2007 Semihalf + * Written by Marian Balakowicz + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#define SDRAM_DDR 1 /* is DDR */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714F0F00 +#define SDRAM_CONFIG1 0x73722930 +#define SDRAM_CONFIG2 0x46770000 +#define SDRAM_TAPDELAY 0x10000000 diff --git a/board/inka4x0/mt46v16m16-75.h b/board/inka4x0/mt46v16m16-75.h index f650faaa109..a78e50e7c60 100644 --- a/board/inka4x0/mt46v16m16-75.h +++ b/board/inka4x0/mt46v16m16-75.h @@ -23,15 +23,10 @@ #define SDRAM_DDR 1 /* is DDR */ -#if defined(CONFIG_MPC5200) /* Settings for XLB = 132 MHz */ #define SDRAM_MODE 0x018D0000 #define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x714f0f00 +#define SDRAM_CONTROL 0x714F0F00 #define SDRAM_CONFIG1 0x73722930 #define SDRAM_CONFIG2 0x47770000 #define SDRAM_TAPDELAY 0x10000000 - -#else -#error CONFIG_MPC5200 not defined -#endif diff --git a/board/inka4x0/mt46v32m16-75.h b/board/inka4x0/mt46v32m16-75.h new file mode 100644 index 00000000000..7eb1f50158f --- /dev/null +++ b/board/inka4x0/mt46v32m16-75.h @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2007 Semihalf + * Written by Marian Balakowicz + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#define SDRAM_DDR 1 /* is DDR */ + +/* Settings for XLB = 132 MHz */ +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x714F0F00 +#define SDRAM_CONFIG1 0x73711930 +#define SDRAM_CONFIG2 0x46770000 +#define SDRAM_TAPDELAY 0x10000000 diff --git a/board/inka4x0/mt48lc16m16a2-75.h b/board/inka4x0/mt48lc16m16a2-75.h index 13a97ac4624..15477259cae 100644 --- a/board/inka4x0/mt48lc16m16a2-75.h +++ b/board/inka4x0/mt48lc16m16a2-75.h @@ -21,27 +21,10 @@ * MA 02111-1307 USA */ -#define SDRAM_DDR 1 /* is SDR */ +#define SDRAM_DDR 0 /* is SDR */ -#if defined(CONFIG_MPC5200) /* Settings for XLB = 132 MHz */ #define SDRAM_MODE 0x00CD0000 -/* #define SDRAM_MODE 0x008D0000 */ /* CAS latency 2 */ #define SDRAM_CONTROL 0x504F0000 #define SDRAM_CONFIG1 0xD2322800 -/* #define SDRAM_CONFIG1 0xD2222800 */ /* CAS latency 2 */ -/*#define SDRAM_CONFIG1 0xD7322800 */ /* SDRAM controller bug workaround */ #define SDRAM_CONFIG2 0x8AD70000 -/*#define SDRAM_CONFIG2 0xDDD70000 */ /* SDRAM controller bug workaround */ - -#elif defined(CONFIG_MGT5100) -/* Settings for XLB = 66 MHz */ -#define SDRAM_MODE 0x008D0000 -#define SDRAM_CONTROL 0x504F0000 -#define SDRAM_CONFIG1 0xC2222600 -#define SDRAM_CONFIG2 0x88B70004 -#define SDRAM_ADDRSEL 0x02000000 - -#else -#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined -#endif diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index af8fb21e276..1617cd49a6e 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -183,7 +183,14 @@ #define CFG_SDRAM_BASE 0x00000000 #define CFG_DEFAULT_MBAR 0x80000000 -#define CONFIG_MPC5200_DDR +/* + * SDRAM controller configuration + */ +#undef CONFIG_SDR_MT48LC16M16A2 +#undef CONFIG_DDR_MT46V16M16 +#undef CONFIG_DDR_MT46V32M16 +#undef CONFIG_DDR_HYB25D512160BF +#define CONFIG_DDR_K4H511638C /* Use ON-Chip SRAM until RAM will be available */ #define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -- cgit v1.3.1 From 5e71c51d74c963d3174060c078dcacf13bdd02ef Mon Sep 17 00:00:00 2001 From: Marian Balakowicz Date: Thu, 15 Nov 2007 13:37:28 +0100 Subject: [INKA4x0] NG hardware: flash support Disabled and remove inka4x0 custom flash driver, use CFI flash driver instead. Signed-off-by: Marian Balakowicz --- board/inka4x0/Makefile | 2 +- board/inka4x0/flash.c | 432 ---------------------------------------------- include/configs/inka4x0.h | 19 +- 3 files changed, 10 insertions(+), 443 deletions(-) delete mode 100644 board/inka4x0/flash.c (limited to 'include') diff --git a/board/inka4x0/Makefile b/board/inka4x0/Makefile index 8aa7e7c8e4a..ddfd2ef8afe 100644 --- a/board/inka4x0/Makefile +++ b/board/inka4x0/Makefile @@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).a -COBJS := $(BOARD).o flash.o +COBJS := $(BOARD).o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/inka4x0/flash.c b/board/inka4x0/flash.c deleted file mode 100644 index b13865530a3..00000000000 --- a/board/inka4x0/flash.c +++ /dev/null @@ -1,432 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include - -flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -/* - * CPU to flash interface is 8-bit, so make declaration accordingly - */ -typedef unsigned char FLASH_PORT_WIDTH; -typedef volatile unsigned char FLASH_PORT_WIDTHV; - -#define FPW FLASH_PORT_WIDTH -#define FPWV FLASH_PORT_WIDTHV - -#define FLASH_CYCLE1 0x0555 -#define FLASH_CYCLE2 0x02aa - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size(FPWV *addr, flash_info_t *info); -static void flash_reset(flash_info_t *info); -static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data); -static flash_info_t *flash_get_info(ulong base); - -/*----------------------------------------------------------------------- - * flash_init() - * - * sets up flash_info and returns size of FLASH (bytes) - */ -unsigned long flash_init (void) -{ - unsigned long size = 0; - extern void flash_preinit(void); - ulong flashbase = CFG_FLASH_BASE; - - flash_preinit(); - - /* Init: no FLASHes known */ - memset(&flash_info[0], 0, sizeof(flash_info_t)); - - flash_info[0].size = - flash_get_size((FPW *)flashbase, &flash_info[0]); - - size = flash_info[0].size; - -#if CFG_MONITOR_BASE >= CFG_FLASH_BASE - /* monitor protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CFG_MONITOR_BASE, - CFG_MONITOR_BASE+monitor_flash_len-1, - flash_get_info(CFG_MONITOR_BASE)); -#endif - -#ifdef CFG_ENV_IS_IN_FLASH - /* ENV protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CFG_ENV_ADDR, - CFG_ENV_ADDR+CFG_ENV_SIZE-1, - flash_get_info(CFG_ENV_ADDR)); -#endif - - return size ? size : 1; -} - -/*----------------------------------------------------------------------- - */ -static void flash_reset(flash_info_t *info) -{ - FPWV *base = (FPWV *)(info->start[0]); - - /* Put FLASH back in read mode */ - if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) - *base = (FPW)0x00FF00FF; /* Intel Read Mode */ - else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD) - *base = (FPW)0x00F000F0; /* AMD Read Mode */ -} - -/*----------------------------------------------------------------------- - */ - -static flash_info_t *flash_get_info(ulong base) -{ - int i; - flash_info_t * info; - - for (i = 0; i < CFG_MAX_FLASH_BANKS; i ++) { - info = & flash_info[i]; - if (info->size && info->start[0] <= base && - base <= info->start[0] + info->size - 1) - break; - } - - return i == CFG_MAX_FLASH_BANKS ? 0 : info; -} - -/*----------------------------------------------------------------------- - */ - -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: printf ("AMD "); break; - case FLASH_MAN_BM: printf ("BRIGHT MICRO "); break; - case FLASH_MAN_FUJ: printf ("FUJITSU "); break; - case FLASH_MAN_SST: printf ("SST "); break; - case FLASH_MAN_STM: printf ("STM "); break; - case FLASH_MAN_INTEL: printf ("INTEL "); break; - default: printf ("Unknown Vendor "); break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_AM116DB: - printf ("AM29LV116DB (16Mbit, bottom boot sect)\n"); - break; - case FLASH_AMLV128U: - printf ("AM29LV128ML (128Mbit, uniform sector size)\n"); - break; - case FLASH_AM160B: - printf ("AM29LV160B (16 Mbit, bottom boot sect)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, - info->sector_count); - - printf (" Sector Start Addresses:"); - - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) { - printf ("\n "); - } - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " "); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ - -/* - * The following code cannot be run from FLASH! - */ - -ulong flash_get_size (FPWV *addr, flash_info_t *info) -{ - int i; - ulong base = (ulong)addr; - - /* Write auto select command: read Manufacturer ID */ - /* Write auto select command sequence and test FLASH answer */ - addr[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* for AMD, Intel ignores this */ - addr[FLASH_CYCLE2] = (FPW)0x00550055; /* for AMD, Intel ignores this */ - addr[FLASH_CYCLE1] = (FPW)0x00900090; /* selects Intel or AMD */ - - /* The manufacturer codes are only 1 byte, so just use 1 byte. - * This works for any bus width and any FLASH device width. - */ - udelay(100); - switch (addr[0] & 0xff) { - - case (uchar)AMD_MANUFACT: - debug ("Manufacturer: AMD (Spansion)\n"); - info->flash_id = FLASH_MAN_AMD; - break; - - case (uchar)INTEL_MANUFACT: - debug ("Manufacturer: Intel (not supported yet)\n"); - info->flash_id = FLASH_MAN_INTEL; - break; - - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - break; - } - - /* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */ - if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[1]) { - - case (uchar)AMD_ID_LV116DB: - debug ("Chip: AM29LV116DB\n"); - info->flash_id += FLASH_AM116DB; - info->sector_count = 35; - info->size = 0x00200000; - /* - * The first 4 sectors are 16 kB, 8 kB, 8 kB and 32 kB, all - * the other ones are 64 kB - */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for( i = 4; i < info->sector_count; i++ ) - info->start[i] = - base + (i * (64 << 10)) - 0x00030000; - break; /* => 2 MB */ - - case (FPW)AMD_ID_LV160B: - debug ("Chip: AM29LV160MB\n"); - info->flash_id += FLASH_AM160B; - info->sector_count = 35; - info->size = 0x00400000; - /* - * The first 4 sectors are 16 kB, 8 kB, 8 kB and 32 kB, all - * the other ones are 64 kB - */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00008000; - info->start[2] = base + 0x0000C000; - info->start[3] = base + 0x00010000; - for( i = 4; i < info->sector_count; i++ ) - info->start[i] = - base + (i * 2 * (64 << 10)) - 0x00060000; - break; /* => 4 MB */ - - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - } - - /* Put FLASH back in read mode */ - flash_reset(info); - - return (info->size); -} - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - FPWV *addr = (FPWV*)(info->start[0]); - int flag, prot, sect, l_sect; - ulong start, now, last; - - debug ("flash_erase: first: %d last: %d\n", s_first, s_last); - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - if ((info->flash_id == FLASH_UNKNOWN) || - (info->flash_id > FLASH_AMD_COMP)) { - printf ("Can't erase unknown flash type %08lx - aborted\n", - info->flash_id); - return 1; - } - - prot = 0; - for (sect=s_first; sect<=s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - addr[0x0555] = (FPW)0x00AA00AA; - addr[0x02AA] = (FPW)0x00550055; - addr[0x0555] = (FPW)0x00800080; - addr[0x0555] = (FPW)0x00AA00AA; - addr[0x02AA] = (FPW)0x00550055; - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (FPWV*)(info->start[sect]); - addr[0] = (FPW)0x00300030; - l_sect = sect; - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - - start = get_timer (0); - last = start; - addr = (FPWV*)(info->start[l_sect]); - while ((addr[0] & (FPW)0x00800080) != (FPW)0x00800080) { - if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return 1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc ('.'); - last = now; - } - } - -DONE: - /* reset to read mode */ - addr = (FPWV*)info->start[0]; - addr[0] = (FPW)0x00F000F0; /* reset bank */ - - printf (" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - int i, rc = 0; - - for (i = 0; i < cnt; i++) - if ((rc = write_word_amd(info, (FPW *)(addr+i), src[i])) != 0) { - return (rc); - } - - return rc; -} - -/*----------------------------------------------------------------------- - * Write a word to Flash for AMD FLASH - * A word is 16 or 32 bits, whichever the bus width of the flash bank - * (not an individual chip) is. - * - * returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data) -{ - ulong start; - int flag; - FPWV *base; /* first address in flash bank */ - - /* Check if Flash is (sufficiently) erased */ - if ((*dest & data) != data) { - return (2); - } - - base = (FPWV *)(info->start[0]); - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - base[FLASH_CYCLE1] = (FPW)0x00AA00AA; /* unlock */ - base[FLASH_CYCLE2] = (FPW)0x00550055; /* unlock */ - base[FLASH_CYCLE1] = (FPW)0x00A000A0; /* selects program mode */ - - *dest = data; /* start programming the data */ - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - start = get_timer (0); - - /* data polling for D7 */ - while ((*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) { - if (get_timer(start) > CFG_FLASH_WRITE_TOUT) { - *dest = (FPW)0x00F000F0; /* reset bank */ - return (1); - } - } - return (0); -} diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index 1617cd49a6e..206007d8846 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -156,21 +156,20 @@ /* * Flash configuration */ -#define CFG_FLASH_BASE 0xFFE00000 - -#define CFG_FLASH_SIZE 0x00200000 /* 2 MByte */ -#define CFG_MAX_FLASH_SECT 35 /* max num of sects on one chip */ - -#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) /* second sector */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks - (= chip selects) */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 +#define CFG_FLASH_BASE 0xffe00000 +#define CFG_FLASH_SIZE 0x00200000 +#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ /* * Environment settings */ #define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_SECT_SIZE 0x2000 #define CONFIG_ENV_OVERWRITE 1 -- cgit v1.3.1 From 8ada0ebf38e4073beea0309188b25d82a112a2ae Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 15 Nov 2007 14:20:08 +0100 Subject: ppc4xx: AMCC Taihu board config file cleanup This patch makes the AMCC Taihu a little more compatible to the other AMCC eval boards. Signed-off-by: Stefan Roese --- include/configs/taihu.h | 44 +++++--------------------------------------- 1 file changed, 5 insertions(+), 39 deletions(-) (limited to 'include') diff --git a/include/configs/taihu.h b/include/configs/taihu.h index c51468b6c8e..d012c60aac8 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -80,6 +80,7 @@ "bootfile=/tftpboot/taihu/uImage\0" \ "rootpath=/opt/eldk/ppc_4xx\0" \ "netdev=eth0\0" \ + "hostname=taihu\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -210,10 +211,12 @@ #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ /*----------------------------------------------------------------------- * I2C stuff @@ -328,7 +331,7 @@ unsigned char spi_read(void); /*----------------------------------------------------------------------- * PPC405 GPIO Configuration */ -#define CFG_440_GPIO_TABLE { /* GPIO Alternate1 */ \ +#define CFG_4xx_GPIO_TABLE { /* GPIO Alternate1 */ \ { \ /* GPIO Core 0 */ \ { GPIO_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG }, /* GPIO0 PerBLast SPI CS */ \ @@ -415,43 +418,6 @@ unsigned char spi_read(void); #define CFG_EBC_PB4AP 0x158FF600 #define CFG_EBC_PB4CR 0x5021A000 -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs - */ -#define CFG_GPIO0_OSRH 0x15555550 /* output select high/low */ -#define CFG_GPIO0_OSRL 0x00000110 -#define CFG_GPIO0_ISR1H 0x00000001 /* input select high/low */ -#define CFG_GPIO0_ISR1L 0x15545440 -#define CFG_GPIO0_TSRH 0x00000000 /* three-state select high/low */ -#define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xFFFE8117 /* three-state control */ -#define CFG_GPIO0_ODR 0x00000000 /* open drain */ - -#define GPIO0 0 /* GPIO controller 0 */ - -/* the GPIO macros in include/ppc405.h for High/Low registers are backwards */ - -#define GPIOx_OSL (GPIO0_OSRH-GPIO_BASE) -#define GPIOx_TSL (GPIO0_TSRH-GPIO_BASE) -#define GPIOx_IS1L (GPIO0_ISR1H-GPIO_BASE) -#define GPIOx_IS2L (GPIO0_ISR1H-GPIO_BASE) -#define GPIOx_IS3L (GPIO0_ISR1H-GPIO_BASE) - -#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO output select */ -#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO three-state select */ -#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO input select */ -#define GPIO_IS2(x) (x+GPIOx_IS1L) -#define GPIO_IS3(x) (x+GPIOx_IS1L) - #define CPLD_REG0_ADDR 0x50100000 #define CPLD_REG1_ADDR 0x50100001 /* -- cgit v1.3.1 From aee747f19b460a0e9da20ff21e90fdaac1cec359 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 15 Nov 2007 14:23:55 +0100 Subject: ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platforms - Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE - Cleanup of the 4xx GPIO functions - Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h Signed-off-by: Stefan Roese --- cpu/ppc4xx/cpu_init.c | 6 +- cpu/ppc4xx/gpio.c | 134 ++++++++++++++++++++------------------------- include/asm-ppc/gpio.h | 35 ++++++++++++ include/configs/lwmon5.h | 2 +- include/configs/pcs440ep.h | 2 +- include/ppc405.h | 2 + include/ppc440.h | 28 ---------- 7 files changed, 101 insertions(+), 108 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c index afb94cc0700..01ab523c512 100644 --- a/cpu/ppc4xx/cpu_init.c +++ b/cpu/ppc4xx/cpu_init.c @@ -112,7 +112,7 @@ cpu_init_f (void) unsigned long val; #endif -#if defined(CONFIG_405EP) || defined (CONFIG_405EX) +#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && !defined(CFG_4xx_GPIO_TABLE) /* * GPIO0 setup (select GPIO or alternate function) */ @@ -144,9 +144,9 @@ cpu_init_f (void) #endif /* CONFIG_405EP */ #endif /* CONFIG_405EP */ -#if defined(CFG_440_GPIO_TABLE) +#if defined(CFG_4xx_GPIO_TABLE) gpio_set_chip_configuration(); -#endif /* CFG_440_GPIO_TABLE */ +#endif /* CFG_4xx_GPIO_TABLE */ /* * External Bus Controller (EBC) Setup diff --git a/cpu/ppc4xx/gpio.c b/cpu/ppc4xx/gpio.c index 50f2fdf1139..dcf1fba8384 100644 --- a/cpu/ppc4xx/gpio.c +++ b/cpu/ppc4xx/gpio.c @@ -26,8 +26,8 @@ #include #include -#if defined(CFG_440_GPIO_TABLE) -gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_440_GPIO_TABLE; +#if defined(CFG_4xx_GPIO_TABLE) +gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_4xx_GPIO_TABLE; #endif #if defined(GPIO0_OSRL) @@ -55,10 +55,10 @@ void gpio_config(int pin, int in_out, int gpio_alt, int out_val) mask2 = 0xc0000000 >> (pin2 << 1); /* first set TCR to 0 */ - out32(GPIO0_TCR + offs, in32(GPIO0_TCR + offs) & ~mask); + out_be32((void *)GPIO0_TCR + offs, in_be32((void *)GPIO0_TCR + offs) & ~mask); if (in_out == GPIO_OUT) { - val = in32(GPIO0_OSRL + offs + offs2) & ~mask2; + val = in_be32((void *)GPIO0_OSRL + offs + offs2) & ~mask2; switch (gpio_alt) { case GPIO_ALT1: val |= GPIO_ALT1_SEL >> pin2; @@ -70,20 +70,23 @@ void gpio_config(int pin, int in_out, int gpio_alt, int out_val) val |= GPIO_ALT3_SEL >> pin2; break; } - out32(GPIO0_OSRL + offs + offs2, val); + out_be32((void *)GPIO0_OSRL + offs + offs2, val); /* setup requested output value */ if (out_val == GPIO_OUT_0) - out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) & ~mask); + out_be32((void *)GPIO0_OR + offs, + in_be32((void *)GPIO0_OR + offs) & ~mask); else if (out_val == GPIO_OUT_1) - out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) | mask); + out_be32((void *)GPIO0_OR + offs, + in_be32((void *)GPIO0_OR + offs) | mask); /* now configure TCR to drive output if selected */ - out32(GPIO0_TCR + offs, in32(GPIO0_TCR + offs) | mask); + out_be32((void *)GPIO0_TCR + offs, + in_be32((void *)GPIO0_TCR + offs) | mask); } else { - val = in32(GPIO0_ISR1L + offs + offs2) & ~mask2; + val = in_be32((void *)GPIO0_ISR1L + offs + offs2) & ~mask2; val |= GPIO_IN_SEL >> pin2; - out32(GPIO0_ISR1L + offs + offs2, val); + out_be32((void *)GPIO0_ISR1L + offs + offs2, val); } } #endif /* GPIO_OSRL */ @@ -98,9 +101,11 @@ void gpio_write_bit(int pin, int val) } if (val) - out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) | GPIO_VAL(pin)); + out_be32((void *)GPIO0_OR + offs, + in_be32((void *)GPIO0_OR + offs) | GPIO_VAL(pin)); else - out32(GPIO0_OR + offs, in32(GPIO0_OR + offs) & ~GPIO_VAL(pin)); + out_be32((void *)GPIO0_OR + offs, + in_be32((void *)GPIO0_OR + offs) & ~GPIO_VAL(pin)); } int gpio_read_out_bit(int pin) @@ -112,10 +117,10 @@ int gpio_read_out_bit(int pin) pin -= GPIO_MAX; } - return (in32(GPIO0_OR + offs) & GPIO_VAL(pin) ? 1 : 0); + return (in_be32((void *)GPIO0_OR + offs) & GPIO_VAL(pin) ? 1 : 0); } -#if defined(CFG_440_GPIO_TABLE) +#if defined(CFG_4xx_GPIO_TABLE) void gpio_set_chip_configuration(void) { unsigned char i=0, j=0, offs=0, gpio_core; @@ -141,24 +146,24 @@ void gpio_set_chip_configuration(void) break; case GPIO_ALT1: - reg = in32(GPIO_IS1(core_add+offs)) + reg = in_be32((void *)GPIO_IS1(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_IN_SEL >> (j*2)); - out32(GPIO_IS1(core_add+offs), reg); + out_be32((void *)GPIO_IS1(core_add+offs), reg); break; case GPIO_ALT2: - reg = in32(GPIO_IS2(core_add+offs)) + reg = in_be32((void *)GPIO_IS2(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_IN_SEL >> (j*2)); - out32(GPIO_IS2(core_add+offs), reg); + out_be32((void *)GPIO_IS2(core_add+offs), reg); break; case GPIO_ALT3: - reg = in32(GPIO_IS3(core_add+offs)) + reg = in_be32((void *)GPIO_IS3(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_IN_SEL >> (j*2)); - out32(GPIO_IS3(core_add+offs), reg); + out_be32((void *)GPIO_IS3(core_add+offs), reg); break; } } @@ -168,87 +173,66 @@ void gpio_set_chip_configuration(void) switch (gpio_tab[gpio_core][i].alt_nb) { case GPIO_SEL: - if (gpio_core == GPIO0) { - /* - * Setup output value - * 1 -> high level - * 0 -> low level - * else -> don't touch - */ - reg = in32(GPIO0_OR); - if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_1) - reg |= (0x80000000 >> (i)); - else if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_0) - reg &= ~(0x80000000 >> (i)); - out32(GPIO0_OR, reg); - - reg = in32(GPIO0_TCR) | (0x80000000 >> (i)); - out32(GPIO0_TCR, reg); - } - -#ifdef GPIO1 - if (gpio_core == GPIO1) { - /* - * Setup output value - * 1 -> high level - * 0 -> low level - * else -> don't touch - */ - reg = in32(GPIO1_OR); - if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_1) - reg |= (0x80000000 >> (i)); - else if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_0) - reg &= ~(0x80000000 >> (i)); - out32(GPIO1_OR, reg); - - reg = in32(GPIO1_TCR) | (0x80000000 >> (i)); - out32(GPIO1_TCR, reg); - } -#endif /* GPIO1 */ - - reg = in32(GPIO_OS(core_add+offs)) + /* + * Setup output value + * 1 -> high level + * 0 -> low level + * else -> don't touch + */ + reg = in_be32((void *)GPIO_OR(core_add)); + if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_1) + reg |= (0x80000000 >> (i)); + else if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_0) + reg &= ~(0x80000000 >> (i)); + out_be32((void *)GPIO_OR(core_add), reg); + + reg = in_be32((void *)GPIO_TCR(core_add)) | + (0x80000000 >> (i)); + out_be32((void *)GPIO_TCR(core_add), reg); + + reg = in_be32((void *)GPIO_OS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); - out32(GPIO_OS(core_add+offs), reg); - reg = in32(GPIO_TS(core_add+offs)) + out_be32((void *)GPIO_OS(core_add+offs), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); - out32(GPIO_TS(core_add+offs), reg); + out_be32((void *)GPIO_TS(core_add+offs), reg); break; case GPIO_ALT1: - reg = in32(GPIO_OS(core_add+offs)) + reg = in_be32((void *)GPIO_OS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT1_SEL >> (j*2)); - out32(GPIO_OS(core_add+offs), reg); - reg = in32(GPIO_TS(core_add+offs)) + out_be32((void *)GPIO_OS(core_add+offs), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT1_SEL >> (j*2)); - out32(GPIO_TS(core_add+offs), reg); + out_be32((void *)GPIO_TS(core_add+offs), reg); break; case GPIO_ALT2: - reg = in32(GPIO_OS(core_add+offs)) + reg = in_be32((void *)GPIO_OS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT2_SEL >> (j*2)); - out32(GPIO_OS(core_add+offs), reg); - reg = in32(GPIO_TS(core_add+offs)) + out_be32((void *)GPIO_OS(core_add+offs), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT2_SEL >> (j*2)); - out32(GPIO_TS(core_add+offs), reg); + out_be32((void *)GPIO_TS(core_add+offs), reg); break; case GPIO_ALT3: - reg = in32(GPIO_OS(core_add+offs)) + reg = in_be32((void *)GPIO_OS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT3_SEL >> (j*2)); - out32(GPIO_OS(core_add+offs), reg); - reg = in32(GPIO_TS(core_add+offs)) + out_be32((void *)GPIO_OS(core_add+offs), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); reg = reg | (GPIO_ALT3_SEL >> (j*2)); - out32(GPIO_TS(core_add+offs), reg); + out_be32((void *)GPIO_TS(core_add+offs), reg); break; } } } } } -#endif /* CFG_440_GPIO_TABLE */ +#endif /* CFG_4xx_GPIO_TABLE */ diff --git a/include/asm-ppc/gpio.h b/include/asm-ppc/gpio.h index c9b6a36b4f9..d0c3eba8846 100644 --- a/include/asm-ppc/gpio.h +++ b/include/asm-ppc/gpio.h @@ -21,6 +21,9 @@ * MA 02111-1307 USA */ +#ifndef __ASM_PPC_GPIO_H +#define __ASM_PPC_GPIO_H + /* 4xx PPC's have 2 GPIO controllers */ #if defined(CONFIG_405EZ) || \ defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ @@ -30,6 +33,36 @@ #define GPIO_GROUP_MAX 1 #endif +/* Offsets */ +#define GPIOx_OR 0x00 /* GPIO Output Register */ +#define GPIOx_TCR 0x04 /* GPIO Three-State Control Register */ +#define GPIOx_OSL 0x08 /* GPIO Output Select Register (Bits 0-31) */ +#define GPIOx_OSH 0x0C /* GPIO Ouput Select Register (Bits 32-63) */ +#define GPIOx_TSL 0x10 /* GPIO Three-State Select Register (Bits 0-31) */ +#define GPIOx_TSH 0x14 /* GPIO Three-State Select Register (Bits 32-63) */ +#define GPIOx_ODR 0x18 /* GPIO Open drain Register */ +#define GPIOx_IR 0x1C /* GPIO Input Register */ +#define GPIOx_RR1 0x20 /* GPIO Receive Register 1 */ +#define GPIOx_RR2 0x24 /* GPIO Receive Register 2 */ +#define GPIOx_RR3 0x28 /* GPIO Receive Register 3 */ +#define GPIOx_IS1L 0x30 /* GPIO Input Select Register 1 (Bits 0-31) */ +#define GPIOx_IS1H 0x34 /* GPIO Input Select Register 1 (Bits 32-63) */ +#define GPIOx_IS2L 0x38 /* GPIO Input Select Register 2 (Bits 0-31) */ +#define GPIOx_IS2H 0x3C /* GPIO Input Select Register 2 (Bits 32-63) */ +#define GPIOx_IS3L 0x40 /* GPIO Input Select Register 3 (Bits 0-31) */ +#define GPIOx_IS3H 0x44 /* GPIO Input Select Register 3 (Bits 32-63) */ + +#define GPIO_OR(x) (x+GPIOx_OR) /* GPIO Output Register */ +#define GPIO_TCR(x) (x+GPIOx_TCR) /* GPIO Three-State Control Register */ +#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO Output Select Register High or Low */ +#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO Three-state Control Reg High or Low */ +#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO Input register1 High or Low */ +#define GPIO_IS2(x) (x+GPIOx_IS2L) /* GPIO Input register2 High or Low */ +#define GPIO_IS3(x) (x+GPIOx_IS3L) /* GPIO Input register3 High or Low */ + +#define GPIO0 0 +#define GPIO1 1 + #define GPIO_MAX 32 #define GPIO_ALT1_SEL 0x40000000 #define GPIO_ALT2_SEL 0x80000000 @@ -56,3 +89,5 @@ void gpio_config(int pin, int in_out, int gpio_alt, int out_val); void gpio_write_bit(int pin, int val); int gpio_read_out_bit(int pin); void gpio_set_chip_configuration(void); + +#endif /* __ASM_PPC_GPIO_H */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 3180617b1e0..9cb483d3ca7 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -414,7 +414,7 @@ /*----------------------------------------------------------------------- * PPC440 GPIO Configuration */ -#define CFG_440_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index d467338e920..d66f4bd449b 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -365,7 +365,7 @@ /*----------------------------------------------------------------------- * PPC440 GPIO Configuration */ -#define CFG_440_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_NO_CHG}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ diff --git a/include/ppc405.h b/include/ppc405.h index 2c5591726c3..e5051d45956 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -1135,6 +1135,8 @@ #endif /* CONFIG_405EZ */ +#define GPIO0_BASE GPIO_BASE + #if defined(CONFIG_405EX) #define SDR0_SRST 0x0200 diff --git a/include/ppc440.h b/include/ppc440.h index 2f841fa6bc6..dfa3d2a6100 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -3187,9 +3187,6 @@ /****************************************************************************** * GPIO macro register defines ******************************************************************************/ -#define GPIO0 0 -#define GPIO1 1 - #if defined(CONFIG_440GP) || defined(CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000700) @@ -3205,31 +3202,6 @@ #define GPIO0_BASE (CFG_PERIPHERAL_BASE+0x00000B00) #define GPIO1_BASE (CFG_PERIPHERAL_BASE+0x00000C00) -/* Offsets */ -#define GPIOx_OR 0x00 /* GPIO Output Register */ -#define GPIOx_TCR 0x04 /* GPIO Three-State Control Register */ -#define GPIOx_OSL 0x08 /* GPIO Output Select Register (Bits 0-31) */ -#define GPIOx_OSH 0x0C /* GPIO Ouput Select Register (Bits 32-63) */ -#define GPIOx_TSL 0x10 /* GPIO Three-State Select Register (Bits 0-31) */ -#define GPIOx_TSH 0x14 /* GPIO Three-State Select Register (Bits 32-63) */ -#define GPIOx_ODR 0x18 /* GPIO Open drain Register */ -#define GPIOx_IR 0x1C /* GPIO Input Register */ -#define GPIOx_RR1 0x20 /* GPIO Receive Register 1 */ -#define GPIOx_RR2 0x24 /* GPIO Receive Register 2 */ -#define GPIOx_RR3 0x28 /* GPIO Receive Register 3 */ -#define GPIOx_IS1L 0x30 /* GPIO Input Select Register 1 (Bits 0-31) */ -#define GPIOx_IS1H 0x34 /* GPIO Input Select Register 1 (Bits 32-63) */ -#define GPIOx_IS2L 0x38 /* GPIO Input Select Register 2 (Bits 0-31) */ -#define GPIOx_IS2H 0x3C /* GPIO Input Select Register 2 (Bits 32-63) */ -#define GPIOx_IS3L 0x40 /* GPIO Input Select Register 3 (Bits 0-31) */ -#define GPIOx_IS3H 0x44 /* GPIO Input Select Register 3 (Bits 32-63) */ - -#define GPIO_OS(x) (x+GPIOx_OSL) /* GPIO Output Register High or Low */ -#define GPIO_TS(x) (x+GPIOx_TSL) /* GPIO Three-state Control Reg High or Low */ -#define GPIO_IS1(x) (x+GPIOx_IS1L) /* GPIO Input register1 High or Low */ -#define GPIO_IS2(x) (x+GPIOx_IS2L) /* GPIO Input register2 High or Low */ -#define GPIO_IS3(x) (x+GPIOx_IS3L) /* GPIO Input register3 High or Low */ - #define GPIO0_OR (GPIO0_BASE+0x0) #define GPIO0_TCR (GPIO0_BASE+0x4) #define GPIO0_OSRL (GPIO0_BASE+0x8) -- cgit v1.3.1 From ecdcbd4f8c1f8cefd785752f4e7536aae2a4ecf9 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 16 Nov 2007 14:00:59 +0100 Subject: ppc4xx: Update AMCC Makalu for board rev 1.1 This patch adds changes needed for Makalu rev 1.1: - Enable 2nd DDR2 bank resulting in 256MByte of SDRAM - Enable 2nd ethernet port EMAC1 - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) - Reset PCIe ports via GPIO upon bootup Signed-off-by: Stefan Roese --- board/amcc/makalu/init.S | 10 ++---- board/amcc/makalu/makalu.c | 57 +++++++-------------------------- include/configs/makalu.h | 78 +++++++++++++++++++++++++++++----------------- 3 files changed, 62 insertions(+), 83 deletions(-) (limited to 'include') diff --git a/board/amcc/makalu/init.S b/board/amcc/makalu/init.S index 806f5fdee2e..57c1774e028 100644 --- a/board/amcc/makalu/init.S +++ b/board/amcc/makalu/init.S @@ -54,14 +54,8 @@ ext_bus_cntlr_init: /* base=00000000, size=128MByte (5), mode=2 (n*10*4) */ mtsdram_as(SDRAM_MB0CF, 0x00005201); - /* SET SDRAM_MB1CF - Not enabled */ - mtsdram_as(SDRAM_MB1CF, 0x00000000); - - /* SET SDRAM_MB2CF - Not enabled */ - mtsdram_as(SDRAM_MB2CF, 0x00000000); - - /* SET SDRAM_MB3CF - Not enabled */ - mtsdram_as(SDRAM_MB3CF, 0x00000000); + /* base=08000000, size=128MByte (5), mode=2 (n*10*4) */ + mtsdram_as(SDRAM_MB1CF, (0x08000000 >> 3) | 0x5201); /* SDRAM_CLKTR: Adv Addr clock by 90 deg */ mtsdram_as(SDRAM_CLKTR,0x80000000); diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c index 3b4a9c15477..b7933a056d1 100644 --- a/board/amcc/makalu/makalu.c +++ b/board/amcc/makalu/makalu.c @@ -26,7 +26,8 @@ #include #include #include -#include +#include +#include #if defined(CONFIG_PCI) #include @@ -189,6 +190,11 @@ int board_early_init_f (void) */ mtsdr(SDR0_SRST, 0); + /* Reset PCIe slots */ + gpio_write_bit(CFG_GPIO_PCIE_RST, 0); + udelay(100); + gpio_write_bit(CFG_GPIO_PCIE_RST, 1); + return 0; } @@ -239,45 +245,6 @@ int pci_pre_init(struct pci_controller * hose ) } #endif /* defined(CONFIG_PCI) */ -/************************************************************************* - * pci_target_init - * - * The bootstrap configuration provides default settings for the pci - * inbound map (PIM). But the bootstrap config choices are limited and - * may not be sufficient for a given board. - * - ************************************************************************/ -#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) -void pci_target_init(struct pci_controller * hose ) -{ - /*-------------------------------------------------------------------+ - * Disable everything - *-------------------------------------------------------------------*/ - out32r( PCIX0_PIM0SA, 0 ); /* disable */ - out32r( PCIX0_PIM1SA, 0 ); /* disable */ - out32r( PCIX0_PIM2SA, 0 ); /* disable */ - out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */ - - /*-------------------------------------------------------------------+ - * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 - * strapping options to not support sizes such as 128/256 MB. - *-------------------------------------------------------------------*/ - out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE ); - out32r( PCIX0_PIM0LAH, 0 ); - out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 ); - - out32r( PCIX0_BAR0, 0 ); - - /*-------------------------------------------------------------------+ - * Program the board's subsystem id/vendor id - *-------------------------------------------------------------------*/ - out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID ); - out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID ); - - out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY ); -} -#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */ - #ifdef CONFIG_PCI static struct pci_controller pcie_hose[2] = {{0},{0}}; @@ -292,15 +259,13 @@ void pcie_setup_hoses(int busno) for (i = 0; i < 2; i++) { - if (is_end_point(i)) { - printf("PCIE%d: will be configured as endpoint\n", i); + if (is_end_point(i)) ret = ppc4xx_init_pcie_endport(i); - } else { - printf("PCIE%d: will be configured as root-complex\n", i); + else ret = ppc4xx_init_pcie_rootport(i); - } if (ret) { - printf("PCIE%d: initialization failed\n", i); + printf("PCIE%d: initialization as %s failed\n", i, + is_end_point(i) ? "endpoint" : "root-complex"); continue; } diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 30707799f5c..aa421c1392a 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -44,11 +44,11 @@ * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFE000000 +#define CFG_FLASH_BASE 0xFC000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ #define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- @@ -113,7 +113,7 @@ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM 128 +#define CFG_MBYTES_SDRAM 256 /*----------------------------------------------------------------------- * I2C @@ -150,7 +150,7 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ -#define CONFIG_PHY1_ADDR 2 +#define CONFIG_PHY1_ADDR 0 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -187,8 +187,8 @@ "bootfile=makalu/uImage\0" \ "fdt_file=makalu/makalu.dtb\0" \ "fdt_addr=400000\0" \ - "kernel_addr=fe000000\0" \ - "ramdisk_addr=fe200000\0" \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc200000\0" \ "initrd_high=30000000\0" \ "load=tftp 200000 makalu/u-boot.bin\0" \ "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ @@ -282,6 +282,7 @@ #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ /*----------------------------------------------------------------------- * PCI stuff @@ -323,7 +324,7 @@ *----------------------------------------------------------------------*/ /* Memory Bank 0 (NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x04011000 -#define CFG_EBC_PB0CR 0xFE0BA000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/ +#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) /* Memory Bank 2 (CPLD) initialization */ #define CFG_EBC_PB2AP 0x9400C800 @@ -334,28 +335,47 @@ /*----------------------------------------------------------------------- * GPIO Setup *----------------------------------------------------------------------*/ -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EX specific) - * - * GPIO0[0-3] - EBC data 0-3 inputs/outputs - * GPIO0[4-7] - USB data 4-7 inputs/outputs - * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs - * GPIO0[12-15] - USB data 0-3 inputs/outputs - * GPIO0[16-21] - UART0 control signal inputs/outputs - * - * GPIO0[22-25,27] - EBC control signal inputs/outputs - * GPIO0[26] - Instruction trace outputs - * GPIO0[28] - Float, N/C - * GPIO0[29-31] - DMA control signal inputs/outputs - */ -#define CFG_GPIO0_OSRL 0x00AA54AA -#define CFG_GPIO0_OSRH 0x55500000 -#define CFG_GPIO0_TSRL 0x00AA54AA -#define CFG_GPIO0_TSRH 0x55500000 -#define CFG_GPIO0_ISR1L 0x00005400 -#define CFG_GPIO0_ISR1H 0x55500000 -#define CFG_GPIO0_ISR2L 0x00550055 -#define CFG_GPIO0_ISR2H 0x00000000 +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ +} \ +} + +#define CFG_GPIO_PCIE_RST 23 +#define CFG_GPIO_PCIE_CLKREQ 27 +#define CFG_GPIO_PCIE_WAKE 28 /* * Internal Definitions -- cgit v1.3.1 From f31d38b9eea9b32f6a1ac848a298cc71ca4c9a03 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 16 Nov 2007 14:16:54 +0100 Subject: ppc4xx: Enable 405EX PCIe UTL register configuration Till now the UTL registers on 405EX were not initialized but left with their default values. This patch new initializes some of the UTL registers on 405EX. Signed-off-by: Stefan Roese --- cpu/ppc4xx/4xx_pcie.c | 44 ++++++++++++++++++++++++++++++++++++++++++-- cpu/ppc4xx/cpu.c | 2 -- include/asm-ppc/4xx_pcie.h | 2 ++ include/common.h | 2 +- 4 files changed, 45 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/4xx_pcie.c b/cpu/ppc4xx/4xx_pcie.c index de7955280e0..cafd9338900 100644 --- a/cpu/ppc4xx/4xx_pcie.c +++ b/cpu/ppc4xx/4xx_pcie.c @@ -401,6 +401,48 @@ int ppc4xx_init_pcie(void) return 0; } #else +static void ppc4xx_setup_utl(u32 port) +{ + u32 utl_base; + + /* + * Map UTL registers at 0xef4f_n000 (4K 0xfff mask) PEGPLn_REGMSK + */ + switch (port) { + case 0: + mtdcr(DCRN_PEGPL_REGBAH(PCIE0), 0x00000000); + mtdcr(DCRN_PEGPL_REGBAL(PCIE0), CFG_PCIE0_UTLBASE); + mtdcr(DCRN_PEGPL_REGMSK(PCIE0), 0xfffffc01); /* 4k region, valid */ + mtdcr(DCRN_PEGPL_SPECIAL(PCIE0), 0); + break; + + case 1: + mtdcr(DCRN_PEGPL_REGBAH(PCIE1), 0x00000000); + mtdcr(DCRN_PEGPL_REGBAL(PCIE1), CFG_PCIE1_UTLBASE); + mtdcr(DCRN_PEGPL_REGMSK(PCIE1), 0xfffffc01); /* 4k region, valid */ + mtdcr(DCRN_PEGPL_SPECIAL(PCIE1), 0); + + break; + } + utl_base = (port==0) ? CFG_PCIE0_UTLBASE : CFG_PCIE1_UTLBASE; + + /* + * Set buffer allocations and then assert VRB and TXE. + */ + out_be32((u32 *)(utl_base + PEUTL_OUTTR), 0x02000000); + out_be32((u32 *)(utl_base + PEUTL_INTR), 0x02000000); + out_be32((u32 *)(utl_base + PEUTL_OPDBSZ), 0x04000000); + out_be32((u32 *)(utl_base + PEUTL_PBBSZ), 0x21000000); + out_be32((u32 *)(utl_base + PEUTL_IPHBSZ), 0x02000000); + out_be32((u32 *)(utl_base + PEUTL_IPDBSZ), 0x04000000); + out_be32((u32 *)(utl_base + PEUTL_RCIRQEN), 0x00f00000); + out_be32((u32 *)(utl_base + PEUTL_PCTL), 0x80800066); + + out_be32((u32 *)(utl_base + PEUTL_PBCTL), 0x0800000c); + out_be32((u32 *)(utl_base + PEUTL_RCSTA), + in_be32((u32 *)(utl_base + PEUTL_RCSTA)) | 0x000040000); +} + int ppc4xx_init_pcie(void) { /* @@ -643,14 +685,12 @@ int ppc4xx_init_pcie_port(int port, int rootport) return -1; } -#if defined(CONFIG_440SPE) /* * Setup UTL registers - but only on revA! * We use default settings for revB chip. */ if (!ppc440spe_revB()) ppc4xx_setup_utl(port); -#endif /* * We map PCI Express configuration access into the 512MB regions diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index d376f52a608..9e9c685afe3 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -510,7 +510,6 @@ int checkcpu (void) return 0; } -#if defined (CONFIG_440SPE) int ppc440spe_revB() { unsigned int pvr; @@ -520,7 +519,6 @@ int ppc440spe_revB() { else return 0; } -#endif /* ------------------------------------------------------------------------- */ diff --git a/include/asm-ppc/4xx_pcie.h b/include/asm-ppc/4xx_pcie.h index ffe07706a31..4c03b050fef 100644 --- a/include/asm-ppc/4xx_pcie.h +++ b/include/asm-ppc/4xx_pcie.h @@ -203,6 +203,7 @@ /* * UTL register offsets */ +#define PEUTL_PBCTL 0x00 #define PEUTL_PBBSZ 0x20 #define PEUTL_OPDBSZ 0x68 #define PEUTL_IPHBSZ 0x70 @@ -210,6 +211,7 @@ #define PEUTL_OUTTR 0x90 #define PEUTL_INTR 0x98 #define PEUTL_PCTL 0xa0 +#define PEUTL_RCSTA 0xb0 #define PEUTL_RCIRQEN 0xb8 /* diff --git a/include/common.h b/include/common.h index 46ed6bd97b3..77aed1a318d 100644 --- a/include/common.h +++ b/include/common.h @@ -516,10 +516,10 @@ void get_sys_info ( sys_info_t * ); # if defined(CONFIG_440SPE) unsigned long determine_sysper(void); unsigned long determine_pci_clock_per(void); - int ppc440spe_revB(void); # endif # endif typedef PPC4xx_SYS_INFO sys_info_t; +int ppc440spe_revB(void); void get_sys_info ( sys_info_t * ); #endif -- cgit v1.3.1 From 9ea61b57968554eaf0f474ec7e088b17d367f474 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 17 Nov 2007 14:52:29 +0100 Subject: ppc4xx: Update AMCC Kilauea config file - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) Signed-off-by: Stefan Roese --- include/configs/kilauea.h | 60 +++++++++++++++++++++++++++++------------------ 1 file changed, 37 insertions(+), 23 deletions(-) (limited to 'include') diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index ddd064ad1da..b4144b39f20 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -430,29 +430,43 @@ /*----------------------------------------------------------------------- * GPIO Setup *----------------------------------------------------------------------*/ -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EX specific) - * - * GPIO0[0-3] - EBC data 0-3 inputs/outputs - * GPIO0[4-7] - USB data 4-7 inputs/outputs - * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs - * GPIO0[12-15] - USB data 0-3 inputs/outputs - * GPIO0[16-21] - UART0 control signal inputs/outputs - * - * GPIO0[22-25,27] - EBC control signal inputs/outputs - * GPIO0[26] - Instruction trace outputs - * GPIO0[28] - Float, N/C - * GPIO0[29-31] - DMA control signal inputs/outputs - */ -#define CFG_GPIO0_OSRL 0x00AA54AA -#define CFG_GPIO0_OSRH 0x21800000 -#define CFG_GPIO0_TSRL 0x00AA55AA -#define CFG_GPIO0_TSRH 0xA5A00000 - -#define CFG_GPIO0_ISR1L 0x00000100 -#define CFG_GPIO0_ISR1H 0x04000000 -#define CFG_GPIO0_ISR2L 0x00550055 -#define CFG_GPIO0_ISR2H 0x40100000 +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ +} \ +} /* * Internal Definitions -- cgit v1.3.1 From 68b88999da87ab88e71e1306192905be3450198e Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Tue, 20 Nov 2007 15:02:26 -0600 Subject: 8610HPCD: Enable the 8610 Display Interface Unit Signed-off-by: Jon Loeliger --- include/configs/MPC8610HPCD.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index ef1310f606b..55df5aa10e6 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -24,7 +24,7 @@ #define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ /* video */ -#undef CONFIG_VIDEO +#define CONFIG_VIDEO #if defined(CONFIG_VIDEO) #define CONFIG_CFB_CONSOLE -- cgit v1.3.1 From ca1ce226287270bb01e25b8e3674c701f12edf19 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 26 Nov 2007 15:01:45 +0100 Subject: ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interrupt Signed-off-by: Stefan Roese --- include/configs/kilauea.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index b4144b39f20..2bb5f24667a 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -462,7 +462,7 @@ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ } \ -- cgit v1.3.1 From 63362cfc6baa97ae0e37ba2c6ece530fcac9f79e Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Mon, 26 Nov 2007 15:06:14 +0100 Subject: ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usage As suggested by Senao, use a different EBC_PB0AP setup for 400MHz operation. Signed-off-by: Stefan Roese --- include/configs/makalu.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/makalu.h b/include/configs/makalu.h index aa421c1392a..18e6dafea1c 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -323,7 +323,7 @@ * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x04011000 +#define CFG_EBC_PB0AP 0x08033700 #define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) /* Memory Bank 2 (CPLD) initialization */ -- cgit v1.3.1 From 8be760903645af09871be50ad0a6f9ebb62b311d Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 27 Nov 2007 11:57:35 +0100 Subject: ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexing After an error in the AMCC 405EX users manual now correctly configure IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ usage. Signed-off-by: Stefan Roese --- include/configs/kilauea.h | 14 +++++++------- include/configs/makalu.h | 12 ++++++------ 2 files changed, 13 insertions(+), 13 deletions(-) (limited to 'include') diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 2bb5f24667a..98d745cc3a0 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -441,16 +441,16 @@ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ -{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \ @@ -462,9 +462,9 @@ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO28 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \ } \ } diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 18e6dafea1c..e04efb771b0 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -346,9 +346,9 @@ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \ {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ @@ -367,9 +367,9 @@ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \ -{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \ -{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \ +{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \ } \ } -- cgit v1.3.1 From a90921f71d225bf9e0f0fc7b8beadeb8001bf78a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 4 Dec 2007 16:29:48 +0100 Subject: ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 support Signed-off-by: Stefan Roese --- include/configs/yosemite.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include') diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 2dde9bee30e..a8eeff989c3 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -160,6 +160,14 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_AD7414 1 /* use AD7414 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + #define CONFIG_PREBOOT "echo;" \ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ "echo" @@ -273,6 +281,7 @@ #define CONFIG_CMD_ASKENV #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG +#define CONFIG_CMD_DTT #define CONFIG_CMD_ELF #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C -- cgit v1.3.1 From a27044b14a9e93678a82d7b35f202b93e7687abc Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 6 Dec 2007 05:58:43 +0100 Subject: ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by setting the FIXD bit in the SDR0_MFR register. Here a description of the symptoms: Problem Description ------------------------------ If a DMA is performed between memory and PCI with the DMA 1 Controller using prefetch, and as a result uses a special purpose buffer selected by the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29), the first part of the transfer sequence is performed twice. The PPC440SPe PCI Controller requests more data than was needed such that in the case of enforce memory protection, a host CPU exception can occur. No data is corrupted, because data transfer is stopped in the PCI Controller. Prefetch enable is specified by setting DMA Configuration Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0. Behavior that may be observed in a running system --------------------------------------------------------------------------- 1. DMA performance is decreased because of the double access on the PCI bus interface. 2. If an illegal access to some address on the PCI bus is detected at the system level, a machine check or similar system error may occur. Workarounds Available ---------------------------------- 1. Do not program prefetch. Note that a prefetch command cannot be programmed without selecting a special purpose buffer. 2. To avoid crossing a physical boundary of the PCI slave device, add 512 bytes of address to the PCI address range. This patch was originally provided by Pravin M. Bathija from AMCC and slighly changed. Signed-off-by: Pravin M. Bathija Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 7 +++---- board/amcc/luan/luan.c | 6 ++++++ board/amcc/yucca/yucca.c | 8 ++++---- include/ppc440.h | 2 ++ 4 files changed, 15 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index 669b828a127..39a3ef16956 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -217,10 +217,9 @@ int board_early_init_f (void) mtdcr (uic0sr, 0x00000000); /* clear all interrupts*/ mtdcr (uic0sr, 0xffffffff); /* clear all interrupts*/ -/* SDR0_MFR should be part of Ethernet init */ - mfsdr (sdr_mfr, mfr); - mfr &= ~SDR0_MFR_ECS_MASK; -/* mtsdr(sdr_mfr, mfr); */ + mfsdr(sdr_mfr, mfr); + mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */ + mtsdr(sdr_mfr, mfr); mtsdr(SDR0_PFC0, CFG_PFC0); diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c index 0067ce0e7e5..f964511c572 100644 --- a/board/amcc/luan/luan.c +++ b/board/amcc/luan/luan.c @@ -39,6 +39,8 @@ extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ ************************************************************************/ int board_early_init_f(void) { + u32 mfr; + mtebc( pb0ap, 0x03800000 ); /* set chip selects */ mtebc( pb0cr, 0xffc58000 ); /* ebc0_b0cr, 4MB at 0xffc00000 CS0 */ mtebc( pb1ap, 0x03800000 ); @@ -64,6 +66,10 @@ int board_early_init_f(void) mtdcr( uic0sr, 0x00000000 ); /* clear all interrupts */ mtdcr( uic0sr, 0xffffffff ); + mfsdr(sdr_mfr, mfr); + mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */ + mtsdr(sdr_mfr, mfr); + return 0; } diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c index 17aaa269096..52486cc4c93 100644 --- a/board/amcc/yucca/yucca.c +++ b/board/amcc/yucca/yucca.c @@ -529,10 +529,10 @@ int board_early_init_f (void) mtdcr (uic0sr, 0x00000000); /* clear all interrupts */ mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */ - /* SDR0_MFR should be part of Ethernet init */ - mfsdr (sdr_mfr, mfr); - mfr &= ~SDR0_MFR_ECS_MASK; - /*mtsdr(sdr_mfr, mfr);*/ + mfsdr(sdr_mfr, mfr); + mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */ + mtsdr(sdr_mfr, mfr); + fpga_init(); return 0; diff --git a/include/ppc440.h b/include/ppc440.h index dfa3d2a6100..21e88366941 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -813,6 +813,8 @@ #define SDRAM_BXCF_M_BE_MASK 0x00000001 /* Memory Bank Enable */ #define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */ #define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */ + +#define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */ #endif /* CONFIG_440SPE */ /*----------------------------------------------------------------------------- -- cgit v1.3.1 From 7cfc12a7dcfdb350e2ab76db4dafcc30f7e77c2b Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 8 Dec 2007 14:47:34 +0100 Subject: ppc4xx: 405EX: Correctly enable USB pins This patch selects the USB data pins in the 405EX GPIO and MFC (multi function control) registers. This is done for the AMCC Kilauea and Makalu eval boards. Signed-off-by: Stefan Roese --- board/amcc/kilauea/kilauea.c | 7 +++++++ board/amcc/makalu/makalu.c | 9 +++++++++ include/configs/kilauea.h | 4 ++-- include/configs/makalu.h | 16 ++++++++-------- include/ppc405.h | 13 +++++++++++++ 5 files changed, 39 insertions(+), 10 deletions(-) (limited to 'include') diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c index 36e9e4a2117..96c0dd46003 100644 --- a/board/amcc/kilauea/kilauea.c +++ b/board/amcc/kilauea/kilauea.c @@ -206,6 +206,13 @@ int board_early_init_f (void) (0x80000000 >> (28 + CFG_NAND_CS)); mtsdr(SDR0_CUST0, val); + /* + * Configure PFC (Pin Function Control) registers + * -> Enable USB + */ + val = SDR0_PFC1_USBEN | SDR0_PFC1_USBBIGEN | SDR0_PFC1_GPT_FREQ; + mtsdr(SDR0_PFC1, val); + return 0; } diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c index b7933a056d1..15e51f42925 100644 --- a/board/amcc/makalu/makalu.c +++ b/board/amcc/makalu/makalu.c @@ -43,6 +43,8 @@ extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ */ int board_early_init_f (void) { + u32 val; + /*--------------------------------------------------------------------+ | Interrupt controller setup for the AMCC 405EX(r) PINE evaluation board. +--------------------------------------------------------------------+ @@ -195,6 +197,13 @@ int board_early_init_f (void) udelay(100); gpio_write_bit(CFG_GPIO_PCIE_RST, 1); + /* + * Configure PFC (Pin Function Control) registers + * -> Enable USB + */ + val = SDR0_PFC1_USBEN | SDR0_PFC1_USBBIGEN | SDR0_PFC1_GPT_FREQ; + mtsdr(SDR0_PFC1, val); + return 0; } diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 98d745cc3a0..e3f24a44b61 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -447,8 +447,8 @@ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ {GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ -{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index e04efb771b0..2871a6cac12 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -342,18 +342,18 @@ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \ {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ -{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \ +{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \ {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \ {GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \ diff --git a/include/ppc405.h b/include/ppc405.h index e5051d45956..b5ad38fc527 100644 --- a/include/ppc405.h +++ b/include/ppc405.h @@ -1574,6 +1574,19 @@ #define SDR0_CUST0_CHIPSELGAT_EN1 0x00000004 /* Chip Select1 Gating Enable */ #define SDR0_CUST0_CHIPSELGAT_EN2 0x00000002 /* Chip Select2 Gating Enable */ #define SDR0_CUST0_CHIPSELGAT_EN3 0x00000001 /* Chip Select3 Gating Enable */ + +#define SDR0_PFC0 0x4100 +#define SDR0_PFC1 0x4101 +#define SDR0_PFC1_U1ME 0x02000000 +#define SDR0_PFC1_U0ME 0x00080000 +#define SDR0_PFC1_U0IM 0x00040000 +#define SDR0_PFC1_SIS 0x00020000 +#define SDR0_PFC1_DMAAEN 0x00010000 +#define SDR0_PFC1_DMADEN 0x00008000 +#define SDR0_PFC1_USBEN 0x00004000 +#define SDR0_PFC1_AHBSWAP 0x00000020 +#define SDR0_PFC1_USBBIGEN 0x00000010 +#define SDR0_PFC1_GPT_FREQ 0x0000000f #endif #endif /* __PPC405_H__ */ -- cgit v1.3.1 From 136288847e3b04f2ff357a067ad45e10afa0a24c Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 13 Dec 2007 14:52:53 +0100 Subject: ppc4xx: Bring 4xx fdt support up-to-date This patch update the 4xx fdt support. It enabled fdt booting on the AMCC Kilauea and Sequoia for now. More can follow later quite easily. Signed-off-by: Stefan Roese --- board/amcc/kilauea/kilauea.c | 1 + board/amcc/sequoia/sequoia.c | 25 +++++++++- cpu/ppc4xx/fdt.c | 114 +++++++++++++------------------------------ include/configs/kilauea.h | 3 +- include/configs/sequoia.h | 6 +++ 5 files changed, 66 insertions(+), 83 deletions(-) (limited to 'include') diff --git a/board/amcc/kilauea/kilauea.c b/board/amcc/kilauea/kilauea.c index 96c0dd46003..2ee896abd96 100644 --- a/board/amcc/kilauea/kilauea.c +++ b/board/amcc/kilauea/kilauea.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index 4e47ab395b4..f81f07146da 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -23,9 +23,11 @@ */ #include +#include +#include +#include #include #include -#include DECLARE_GLOBAL_DATA_PTR; @@ -583,3 +585,24 @@ int post_hotkeys_pressed(void) return 0; /* No hotkeys supported */ } #endif /* CONFIG_POST */ + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + u32 val[4]; + int rc; + + ft_cpu_setup(blob, bd); + + /* Fixup NOR mapping */ + val[0] = 0; /* chip select number */ + val[1] = 0; /* always 0 */ + val[2] = gd->bd->bi_flashstart; + val[3] = gd->bd->bi_flashsize; + rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", + val, sizeof(val), 1); + if (rc) + printf("Unable to update property NOR mapping, err=%s\n", + fdt_strerror(rc)); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/cpu/ppc4xx/fdt.c b/cpu/ppc4xx/fdt.c index dcedbbb3083..3ef30004fb7 100644 --- a/cpu/ppc4xx/fdt.c +++ b/cpu/ppc4xx/fdt.c @@ -35,25 +35,18 @@ #if defined(CONFIG_OF_LIBFDT) #include #include +#include DECLARE_GLOBAL_DATA_PTR; -static void do_fixup(void *fdt, const char *node, const char *prop, - const void *val, int len, int create) -{ -#if defined(DEBUG) - int i; - debug("Updating property '%s/%s' = ", node, prop); - for (i = 0; i < len; i++) - debug(" %.2x", *(u8*)(val+i)); - debug("(%d)\n", *(u32 *)val); -#endif - int rc = fdt_find_and_setprop(fdt, node, prop, val, len, create); - if (rc) - printf("Unable to update property %s:%s, err=%s\n", - node, prop, fdt_strerror(rc)); -} +/* + * The aliases needed for this generic etherne MAC address + * fixup function are not in place yet. So don't use this + * approach for now. This will be enabled later. + */ +#undef USES_FDT_ALIASES +#ifndef USES_FDT_ALIASES static void do_fixup_macaddr(void *fdt, int offset, const void *val, int i) { int rc; @@ -69,87 +62,47 @@ static void do_fixup_macaddr(void *fdt, int offset, const void *val, int i) printf("Unable to update property %s, err=%s\n", "local-mac-address", fdt_strerror(rc)); } - -static void do_fixup_u32(void *fdt, const char *node, const char *prop, - u32 val, int create) -{ - val = cpu_to_fdt32(val); - do_fixup(fdt, node, prop, &val, sizeof(val), create); -} - -static void do_fixup_uart(void *fdt, int offset, int i, bd_t *bd) -{ - int rc; - u32 val; - PPC4xx_SYS_INFO sys_info; - - get_sys_info(&sys_info); - - debug("Updating node UART%d: clock-frequency=%d\n", i, gd->uart_clk); - - val = cpu_to_fdt32(gd->uart_clk); - rc = fdt_setprop(fdt, offset, "clock-frequency", &val, 4); - if (rc) - printf("Unable to update node UART, err=%s\n", fdt_strerror(rc)); - - val = cpu_to_fdt32(bd->bi_baudrate); - rc = fdt_setprop(fdt, offset, "current-speed", &val, 4); - if (rc) - printf("Unable to update node UART, err=%s\n", fdt_strerror(rc)); -} +#endif /* USES_FDT_ALIASES */ void ft_cpu_setup(void *blob, bd_t *bd) { - char * cpu_path = "/cpus/" OF_CPU; + char *cpu_path = "/cpus/" OF_CPU; sys_info_t sys_info; int offset; int i; - int tmp[2]; - get_sys_info (&sys_info); + get_sys_info(&sys_info); - do_fixup_u32(blob, cpu_path, "timebase-frequency", bd->bi_intfreq, 1); - do_fixup_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); - do_fixup_u32(blob, "/plb", "clock-frequency", sys_info.freqPLB, 1); - do_fixup_u32(blob, "/plb/opb", "clock-frequency", sys_info.freqOPB, 1); - do_fixup_u32(blob, "/plb/opb/ebc", "clock-frequency", sys_info.freqEBC, 1); - - /* update, or add and update /memory node */ - offset = fdt_find_node_by_path(blob, "/memory"); - if (offset < 0) { - offset = fdt_add_subnode(blob, 0, "memory"); - if (offset < 0) - debug("failed to add /memory node: %s\n", - fdt_strerror(offset)); - } - if (offset >= 0) { - fdt_setprop(blob, offset, "device_type", - "memory", sizeof("memory")); - tmp[0] = cpu_to_fdt32(bd->bi_memstart); - tmp[1] = cpu_to_fdt32(bd->bi_memsize); - fdt_setprop(blob, offset, "reg", tmp, sizeof(tmp)); - debug("Updating /memory node to %d:%d\n", - bd->bi_memstart, bd->bi_memsize); - } + do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", bd->bi_intfreq, 1); + do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_path_u32(blob, "/plb", "clock-frequency", sys_info.freqPLB, 1); + do_fixup_by_path_u32(blob, "/plb/opb", "clock-frequency", sys_info.freqOPB, 1); + do_fixup_by_path_u32(blob, "/plb/opb/ebc", "clock-frequency", + sys_info.freqEBC, 1); + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); /* * Setup all baudrates for the UARTs */ - offset = 0; - for (i = 0; i < 4; i++) { - offset = fdt_find_node_by_type(blob, offset, "serial"); - if (offset < 0) - break; - - do_fixup_uart(blob, offset, i, bd); - } + do_fixup_by_compat_u32(blob, "ns16550", "clock-frequency", gd->uart_clk, 1); +#ifdef USES_FDT_ALIASES /* - * Setup all MAC addresses in fdt + * The aliases needed for this generic etherne MAC address + * fixup function are not in place yet. So don't use this + * approach for now. This will be enabled later. */ - offset = 0; + fdt_fixup_ethernet(blob, bd); +#else + offset = -1; for (i = 0; i < 4; i++) { - offset = fdt_find_node_by_type(blob, offset, "network"); + /* + * FIXME: This will cause problems with emac3 compatible + * devices, like on 405GP. But hopefully when we deal + * with those devices, the aliases stuff will be in + * place. + */ + offset = fdt_node_offset_by_compatible(blob, offset, "ibm,emac4"); if (offset < 0) break; @@ -174,5 +127,6 @@ void ft_cpu_setup(void *blob, bd_t *bd) #endif } } +#endif /* USES_FDT_ALIASES */ } #endif /* CONFIG_OF_LIBFDT */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index e3f24a44b61..bec9fde73aa 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -519,7 +519,6 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,405EX@0" +#define OF_CPU "cpu@0" #endif /* __CONFIG_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 2af675ae146..58acbc090e5 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -487,4 +487,10 @@ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define OF_CPU "cpu@0" + #endif /* __CONFIG_H */ -- cgit v1.3.1 From 052440b022ca8981d39b6f8c10d1aa6326f47480 Mon Sep 17 00:00:00 2001 From: Markus Klotzbücher Date: Fri, 23 Nov 2007 13:09:18 +0100 Subject: ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board config When using dhcp/bootp the "netmask" environment variable is not set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is desireable, so the following patch adds this this option to the board config. Signed-off-by: Markus Klotzbuecher Signed-off-by: Stefan Roese --- include/configs/sequoia.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 58acbc090e5..419ee733498 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -329,6 +329,7 @@ #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_SUBNETMASK /* -- cgit v1.3.1 From 328a340392a5df9aaf00792be989df73e750859e Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 18 Dec 2007 08:44:51 +0100 Subject: ppc4xx: fdt: Cleanup setup of cpu node setup Now the cpu node setup ("timebase-frequency" and "clock-frequency") is without using the absolute path to the cpu node. This makes it possible to use this U-Boot version with both versions of cpu-node naming "cpu@0" and the former "PowerPC,440EPx@0". Signed-off-by: Stefan Roese --- cpu/ppc4xx/fdt.c | 7 ++++--- include/configs/kilauea.h | 1 - include/configs/sequoia.h | 1 - 3 files changed, 4 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/fdt.c b/cpu/ppc4xx/fdt.c index f351b8bf3c0..afcb9740685 100644 --- a/cpu/ppc4xx/fdt.c +++ b/cpu/ppc4xx/fdt.c @@ -36,13 +36,14 @@ DECLARE_GLOBAL_DATA_PTR; void ft_cpu_setup(void *blob, bd_t *bd) { - char *cpu_path = "/cpus/" OF_CPU; sys_info_t sys_info; get_sys_info(&sys_info); - do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", bd->bi_intfreq, 1); - do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, "timebase-frequency", + bd->bi_intfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, "clock-frequency", + bd->bi_intfreq, 1); do_fixup_by_path_u32(blob, "/plb", "clock-frequency", sys_info.freqPLB, 1); do_fixup_by_path_u32(blob, "/plb/opb", "clock-frequency", sys_info.freqOPB, 1); do_fixup_by_path_u32(blob, "/plb/opb/ebc", "clock-frequency", diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index bec9fde73aa..f3e8601d850 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -519,6 +519,5 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -#define OF_CPU "cpu@0" #endif /* __CONFIG_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 419ee733498..48a64e3fd83 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -492,6 +492,5 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -#define OF_CPU "cpu@0" #endif /* __CONFIG_H */ -- cgit v1.3.1 From bf8324e4a50758daff8cddd04c6a2ff8ed775bea Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 19 Dec 2007 09:05:40 +0100 Subject: ppc4xx: Add fdt support to AMCC Katmai eval board Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 23 +++++++++++++++++++++++ include/configs/katmai.h | 12 +++++++++++- 2 files changed, 34 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index 39a3ef16956..25c9a22feab 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -25,6 +25,8 @@ #include #include #include +#include +#include #include #include #include @@ -533,3 +535,24 @@ int post_hotkeys_pressed(void) return (ctrlc()); } #endif + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + u32 val[4]; + int rc; + + ft_cpu_setup(blob, bd); + + /* Fixup NOR mapping */ + val[0] = 0; /* chip select number */ + val[1] = 0; /* always 0 */ + val[2] = gd->bd->bi_flashstart; + val[3] = gd->bd->bi_flashsize; + rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges", + val, sizeof(val), 1); + if (rc) + printf("Unable to update property NOR mapping, err=%s\n", + fdt_strerror(rc)); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 2eed9413f66..0aa4f2dcc05 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -193,8 +193,14 @@ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ + "net_nfs_fdt=tftp 200000 ${bootfile};" \ + "tftp ${fdt_addr} ${fdt_file};" \ + "run nfsargs addip addtty;" \ + "bootm 200000 - ${fdt_addr}\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ "bootfile=katmai/uImage\0" \ + "fdt_file=katmai/katmai.dtb\0" \ + "fdt_addr=400000\0" \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ "initrd_high=30000000\0" \ @@ -445,4 +451,8 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + #endif /* __CONFIG_H */ -- cgit v1.3.1 From b0265b576bb8fa9465f99e99c323768b562fadc2 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 21 Dec 2007 07:51:29 +0100 Subject: ppc4xx: Update Makalu fdt support Signed-off-by: Stefan Roese --- include/configs/makalu.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include') diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 2871a6cac12..8f8e867b83c 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -394,6 +394,4 @@ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -#define OF_CPU "PowerPC,405EX@0" - #endif /* __CONFIG_H */ -- cgit v1.3.1 From 42d55ea0bde06e47d5a3b49b0d91002acd8e5708 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 22 Dec 2007 12:20:09 +0100 Subject: ppc4xx: Move virtual address of POST cache test to bigger address On Sequoia & LWMON5 the virtual address of the POST cache test is now moved to a bigger address. This enables usage of more memory on those boards. Signed-off-by: Stefan Roese --- include/configs/lwmon5.h | 2 +- include/configs/sequoia.h | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 9cb483d3ca7..5210024d8f2 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -153,7 +153,7 @@ CFG_POST_SPR | \ CFG_POST_UART) -#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ +#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ #define CONFIG_LOGBUFFER #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 48a64e3fd83..1f72b54884b 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -377,7 +377,7 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CONFIG_LOGBUFFER -#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ +#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -- cgit v1.3.1 From 9e2c347151db5ae8acf5f18b99493cd53e6637e3 Mon Sep 17 00:00:00 2001 From: Larry Johnson Date: Thu, 27 Dec 2007 09:52:17 -0500 Subject: Add driver for National Semiconductor LM73 temperature sensor This driver is based on the driver for the LM75. Signed-off-by: Larry Johnson --- drivers/hwmon/Makefile | 1 + drivers/hwmon/lm73.c | 181 +++++++++++++++++++++++++++++++++++++++++++++++++ include/dtt.h | 12 +++- 3 files changed, 193 insertions(+), 1 deletion(-) create mode 100644 drivers/hwmon/lm73.c (limited to 'include') diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index cebb2ba6353..32e3f44a916 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -34,6 +34,7 @@ COBJS-y += adm1021.o COBJS-y += ds1621.o COBJS-y += ds1722.o COBJS-y += ds1775.o +COBJS-y += lm73.o COBJS-y += lm75.o COBJS-y += lm81.o diff --git a/drivers/hwmon/lm73.c b/drivers/hwmon/lm73.c new file mode 100644 index 00000000000..f9ae01297bc --- /dev/null +++ b/drivers/hwmon/lm73.c @@ -0,0 +1,181 @@ +/* + * (C) Copyright 2007 + * Larry Johnson, lrj@acm.org + * + * based on dtt/lm75.c which is ... + * + * (C) Copyright 2001 + * Bill Hunter, Wave 7 Optics, williamhunter@mediaone.net + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * National Semiconductor LM73 Temperature Sensor + */ + +#include + +#ifdef CONFIG_DTT_LM73 +#if !defined(CFG_EEPROM_PAGE_WRITE_ENABLE) || \ + (CFG_EEPROM_PAGE_WRITE_BITS < 1) +# error "CFG_EEPROM_PAGE_WRITE_ENABLE must be defined and CFG_EEPROM_PAGE_WRITE_BITS must be greater than 1 to use CONFIG_DTT_LM73" +#endif + +#include +#include + +/* + * Device code + */ +#define DTT_I2C_DEV_CODE 0x48 /* National Semi's LM73 device */ + +int dtt_read(int sensor, int reg) +{ + int dlen; + uchar data[2]; + + /* + * Validate 'reg' param and get register size. + */ + switch (reg) { + case DTT_CONFIG: + case DTT_CONTROL: + dlen = 1; + break; + case DTT_READ_TEMP: + case DTT_TEMP_HIGH: + case DTT_TEMP_LOW: + case DTT_ID: + dlen = 2; + break; + default: + return -1; + } + /* + * Calculate sensor address and register. + */ + sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* calculate LM73 addr */ + /* + * Now try to read the register. + */ + if (i2c_read(sensor, reg, 1, data, dlen) != 0) + return -1; + /* + * Handle 2 byte result. + */ + if (2 == dlen) + return ((int)((short)data[1] + (((short)data[0]) << 8))); + + return (int)data[0]; +} /* dtt_read() */ + +int dtt_write(int sensor, int reg, int val) +{ + int dlen; + uchar data[2]; + + /* + * Validate 'reg' param and handle register size + */ + switch (reg) { + case DTT_CONFIG: + case DTT_CONTROL: + dlen = 1; + data[0] = (char)(val & 0xff); + break; + case DTT_TEMP_HIGH: + case DTT_TEMP_LOW: + dlen = 2; + data[0] = (char)((val >> 8) & 0xff); /* MSB first */ + data[1] = (char)(val & 0xff); + break; + default: + return -1; + } + /* + * Calculate sensor address and register. + */ + sensor = DTT_I2C_DEV_CODE + (sensor & 0x07); /* calculate LM73 addr */ + /* + * Write value to register. + */ + return i2c_write(sensor, reg, 1, data, dlen) != 0; +} /* dtt_write() */ + +static int _dtt_init(int sensor) +{ + int val; + + /* + * Validate the Identification register + */ + if (0x0190 != dtt_read(sensor, DTT_ID)) + return 1; + /* + * Setup THIGH (upper-limit) and TLOW (lower-limit) registers + */ + val = CFG_DTT_MAX_TEMP << 7; + if (dtt_write(sensor, DTT_TEMP_HIGH, val)) + return 1; + + val = CFG_DTT_MIN_TEMP << 7; + if (dtt_write(sensor, DTT_TEMP_LOW, val)) + return 1; + /* + * Setup configuraton register + */ + /* config = alert active low, disabled, and reset */ + val = 0x64; + if (dtt_write(sensor, DTT_CONFIG, val)) + return 1; + /* + * Setup control/status register + */ + /* control = temp resolution 0.25C */ + val = 0x00; + if (dtt_write(sensor, DTT_CONTROL, val)) + return 1; + + dtt_read(sensor, DTT_CONTROL); /* clear temperature flags */ + return 0; +} /* _dtt_init() */ + +int dtt_init(void) +{ + int i; + unsigned char sensors[] = CONFIG_DTT_SENSORS; + const char *const header = "DTT: "; + + for (i = 0; i < sizeof(sensors); i++) { + if (_dtt_init(sensors[i]) != 0) + printf("%s%d FAILED INIT\n", header, i + 1); + else + printf("%s%d is %i C\n", header, i + 1, + dtt_get_temp(sensors[i])); + } + return 0; +} /* dtt_init() */ + +int dtt_get_temp(int sensor) +{ + return (dtt_read(sensor, DTT_READ_TEMP) + 0x0040) >> 7; +} /* dtt_get_temp() */ + +#endif /* CONFIG_DTT_LM73 */ diff --git a/include/dtt.h b/include/dtt.h index 2e8c690158f..4e8aaad87fe 100644 --- a/include/dtt.h +++ b/include/dtt.h @@ -31,7 +31,8 @@ defined(CONFIG_DTT_DS1621) || \ defined(CONFIG_DTT_DS1775) || \ defined(CONFIG_DTT_LM81) || \ - defined(CONFIG_DTT_ADM1021) + defined(CONFIG_DTT_ADM1021) || \ + defined(CONFIG_DTT_LM73) #define CONFIG_DTT /* We have a DTT */ @@ -119,4 +120,13 @@ extern int dtt_get_temp(int sensor); #define DTT_ADM1021_DEVID 0x41 #endif +#if defined(CONFIG_DTT_LM73) +#define DTT_READ_TEMP 0x0 +#define DTT_CONFIG 0x1 +#define DTT_TEMP_HIGH 0x2 +#define DTT_TEMP_LOW 0x3 +#define DTT_CONTROL 0x4 +#define DTT_ID 0x7 +#endif + #endif /* _DTT_H_ */ -- cgit v1.3.1 From c46f53333b22b1f9098676bea8884fc7db820cf3 Mon Sep 17 00:00:00 2001 From: Larry Johnson Date: Sat, 22 Dec 2007 15:15:13 -0500 Subject: Add definitions for 440EPx/GRx SDRAM controller to ppc440.h This patch adds the Denali SDRAM controller definitions to "ppc440.h". It also fixes two typos in the definitions, so the board-specific "sdram.h" files containing these definitions are also fixed to avoid compiler warnings. Signed-off-by: Larry Johnson --- board/amcc/sequoia/sdram.h | 4 +- board/lwmon5/sdram.h | 4 +- include/ppc440.h | 514 ++++++++++++++++++++++++++++++++++++++++----- 3 files changed, 470 insertions(+), 52 deletions(-) (limited to 'include') diff --git a/board/amcc/sequoia/sdram.h b/board/amcc/sequoia/sdram.h index 7f847aa2ad9..6a7bf01efbf 100644 --- a/board/amcc/sequoia/sdram.h +++ b/board/amcc/sequoia/sdram.h @@ -395,8 +395,8 @@ #define DDR0_26_TRAS_MAX_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) #define DDR0_26_TRAS_MAX_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) #define DDR0_26_TREF_MASK 0x00003FFF -#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) -#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) +#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0) +#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF) #define DDR0_27 0x1B #define DDR0_27_EMRS_DATA_MASK 0x3FFF0000 diff --git a/board/lwmon5/sdram.h b/board/lwmon5/sdram.h index 7f847aa2ad9..6a7bf01efbf 100644 --- a/board/lwmon5/sdram.h +++ b/board/lwmon5/sdram.h @@ -395,8 +395,8 @@ #define DDR0_26_TRAS_MAX_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) #define DDR0_26_TRAS_MAX_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) #define DDR0_26_TREF_MASK 0x00003FFF -#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) -#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) +#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0) +#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF) #define DDR0_27 0x1B #define DDR0_27_EMRS_DATA_MASK 0x3FFF0000 diff --git a/include/ppc440.h b/include/ppc440.h index 21e88366941..90e56b0989e 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -19,6 +19,30 @@ | LICENSED MATERIAL - PROGRAM PROPERTY OF I B M +----------------------------------------------------------------------------*/ +/* + * (C) Copyright 2006 + * Sylvie Gohl, AMCC/IBM, gohl.sylvie@fr.ibm.com + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Thierry Roman, AMCC/IBM, thierry_roman@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * Robert Snyder, AMCC/IBM, rob.snyder@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + #ifndef __PPC440_H__ #define __PPC440_H__ @@ -186,54 +210,6 @@ #define sdr_plbtr 0x4200 #define sdr_mfr 0x4300 /* SDR0_MFR reg */ -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* test-only!!!! */ -#define DDR0_00 0x00 -#define DDR0_01 0x01 -#define DDR0_02 0x02 -#define DDR0_03 0x03 -#define DDR0_04 0x04 -#define DDR0_05 0x05 -#define DDR0_06 0x06 -#define DDR0_07 0x07 -#define DDR0_08 0x08 -#define DDR0_09 0x09 -#define DDR0_10 0x0A -#define DDR0_11 0x0B -#define DDR0_12 0x0C -#define DDR0_13 0x0D -#define DDR0_14 0x0E -#define DDR0_15 0x0F -#define DDR0_16 0x10 -#define DDR0_17 0x11 -#define DDR0_18 0x12 -#define DDR0_19 0x13 -#define DDR0_20 0x14 -#define DDR0_21 0x15 -#define DDR0_22 0x16 -#define DDR0_23 0x17 -#define DDR0_24 0x18 -#define DDR0_25 0x19 -#define DDR0_26 0x1A -#define DDR0_27 0x1B -#define DDR0_28 0x1C -#define DDR0_29 0x1D -#define DDR0_30 0x1E -#define DDR0_31 0x1F -#define DDR0_32 0x20 -#define DDR0_33 0x21 -#define DDR0_34 0x22 -#define DDR0_35 0x23 -#define DDR0_36 0x24 -#define DDR0_37 0x25 -#define DDR0_38 0x26 -#define DDR0_39 0x27 -#define DDR0_40 0x28 -#define DDR0_41 0x29 -#define DDR0_42 0x2A -#define DDR0_43 0x2B -#define DDR0_44 0x2C -#endif /*CONFIG_440EPX*/ - /*----------------------------------------------------------------------------- | SDRAM Controller +----------------------------------------------------------------------------*/ @@ -817,6 +793,448 @@ #define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */ #endif /* CONFIG_440SPE */ +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) +/*----------------------------------------------------------------------------- + | SDRAM Controller + +----------------------------------------------------------------------------*/ +#define DDR0_00 0x00 +#define DDR0_00_INT_ACK_MASK 0x7F000000 /* Write only */ +#define DDR0_00_INT_ACK_ALL 0x7F000000 +#define DDR0_00_INT_ACK_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_00_INT_ACK_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +/* Status */ +#define DDR0_00_INT_STATUS_MASK 0x00FF0000 /* Read only */ +/* Bit0. A single access outside the defined PHYSICAL memory space detected. */ +#define DDR0_00_INT_STATUS_BIT0 0x00010000 +/* Bit1. Multiple accesses outside the defined PHYSICAL memory space detected. */ +#define DDR0_00_INT_STATUS_BIT1 0x00020000 +/* Bit2. Single correctable ECC event detected */ +#define DDR0_00_INT_STATUS_BIT2 0x00040000 +/* Bit3. Multiple correctable ECC events detected. */ +#define DDR0_00_INT_STATUS_BIT3 0x00080000 +/* Bit4. Single uncorrectable ECC event detected. */ +#define DDR0_00_INT_STATUS_BIT4 0x00100000 +/* Bit5. Multiple uncorrectable ECC events detected. */ +#define DDR0_00_INT_STATUS_BIT5 0x00200000 +/* Bit6. DRAM initialization complete. */ +#define DDR0_00_INT_STATUS_BIT6 0x00400000 +/* Bit7. Logical OR of all lower bits. */ +#define DDR0_00_INT_STATUS_BIT7 0x00800000 + +#define DDR0_00_INT_STATUS_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16) +#define DDR0_00_INT_STATUS_DECODE(n) ((((unsigned long)(n))>>16)&0xFF) +#define DDR0_00_DLL_INCREMENT_MASK 0x00007F00 +#define DDR0_00_DLL_INCREMENT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_00_DLL_INCREMENT_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_00_DLL_START_POINT_MASK 0x0000007F +#define DDR0_00_DLL_START_POINT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_00_DLL_START_POINT_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_01 0x01 +#define DDR0_01_PLB0_DB_CS_LOWER_MASK 0x1F000000 +#define DDR0_01_PLB0_DB_CS_LOWER_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define DDR0_01_PLB0_DB_CS_LOWER_DECODE(n) ((((unsigned long)(n))>>24)&0x1F) +#define DDR0_01_PLB0_DB_CS_UPPER_MASK 0x001F0000 +#define DDR0_01_PLB0_DB_CS_UPPER_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16) +#define DDR0_01_PLB0_DB_CS_UPPER_DECODE(n) ((((unsigned long)(n))>>16)&0x1F) +#define DDR0_01_OUT_OF_RANGE_TYPE_MASK 0x00000700 /* Read only */ +#define DDR0_01_OUT_OF_RANGE_TYPE_ENCODE(n) ((((unsigned long)(n))&0x7)<<8) +#define DDR0_01_OUT_OF_RANGE_TYPE_DECODE(n) ((((unsigned long)(n))>>8)&0x7) +#define DDR0_01_INT_MASK_MASK 0x000000FF +#define DDR0_01_INT_MASK_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0) +#define DDR0_01_INT_MASK_DECODE(n) ((((unsigned long)(n))>>0)&0xFF) +#define DDR0_01_INT_MASK_ALL_ON 0x000000FF +#define DDR0_01_INT_MASK_ALL_OFF 0x00000000 + +#define DDR0_02 0x02 +#define DDR0_02_MAX_CS_REG_MASK 0x02000000 /* Read only */ +#define DDR0_02_MAX_CS_REG_ENCODE(n) ((((unsigned long)(n))&0x2)<<24) +#define DDR0_02_MAX_CS_REG_DECODE(n) ((((unsigned long)(n))>>24)&0x2) +#define DDR0_02_MAX_COL_REG_MASK 0x000F0000 /* Read only */ +#define DDR0_02_MAX_COL_REG_ENCODE(n) ((((unsigned long)(n))&0xF)<<16) +#define DDR0_02_MAX_COL_REG_DECODE(n) ((((unsigned long)(n))>>16)&0xF) +#define DDR0_02_MAX_ROW_REG_MASK 0x00000F00 /* Read only */ +#define DDR0_02_MAX_ROW_REG_ENCODE(n) ((((unsigned long)(n))&0xF)<<8) +#define DDR0_02_MAX_ROW_REG_DECODE(n) ((((unsigned long)(n))>>8)&0xF) +#define DDR0_02_START_MASK 0x00000001 +#define DDR0_02_START_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_02_START_DECODE(n) ((((unsigned long)(n))>>0)&0x1) +#define DDR0_02_START_OFF 0x00000000 +#define DDR0_02_START_ON 0x00000001 + +#define DDR0_03 0x03 +#define DDR0_03_BSTLEN_MASK 0x07000000 +#define DDR0_03_BSTLEN_ENCODE(n) ((((unsigned long)(n))&0x7)<<24) +#define DDR0_03_BSTLEN_DECODE(n) ((((unsigned long)(n))>>24)&0x7) +#define DDR0_03_CASLAT_MASK 0x00070000 +#define DDR0_03_CASLAT_ENCODE(n) ((((unsigned long)(n))&0x7)<<16) +#define DDR0_03_CASLAT_DECODE(n) ((((unsigned long)(n))>>16)&0x7) +#define DDR0_03_CASLAT_LIN_MASK 0x00000F00 +#define DDR0_03_CASLAT_LIN_ENCODE(n) ((((unsigned long)(n))&0xF)<<8) +#define DDR0_03_CASLAT_LIN_DECODE(n) ((((unsigned long)(n))>>8)&0xF) +#define DDR0_03_INITAREF_MASK 0x0000000F +#define DDR0_03_INITAREF_ENCODE(n) ((((unsigned long)(n))&0xF)<<0) +#define DDR0_03_INITAREF_DECODE(n) ((((unsigned long)(n))>>0)&0xF) + +#define DDR0_04 0x04 +#define DDR0_04_TRC_MASK 0x1F000000 +#define DDR0_04_TRC_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define DDR0_04_TRC_DECODE(n) ((((unsigned long)(n))>>24)&0x1F) +#define DDR0_04_TRRD_MASK 0x00070000 +#define DDR0_04_TRRD_ENCODE(n) ((((unsigned long)(n))&0x7)<<16) +#define DDR0_04_TRRD_DECODE(n) ((((unsigned long)(n))>>16)&0x7) +#define DDR0_04_TRTP_MASK 0x00000700 +#define DDR0_04_TRTP_ENCODE(n) ((((unsigned long)(n))&0x7)<<8) +#define DDR0_04_TRTP_DECODE(n) ((((unsigned long)(n))>>8)&0x7) + +#define DDR0_05 0x05 +#define DDR0_05_TMRD_MASK 0x1F000000 +#define DDR0_05_TMRD_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define DDR0_05_TMRD_DECODE(n) ((((unsigned long)(n))>>24)&0x1F) +#define DDR0_05_TEMRS_MASK 0x00070000 +#define DDR0_05_TEMRS_ENCODE(n) ((((unsigned long)(n))&0x7)<<16) +#define DDR0_05_TEMRS_DECODE(n) ((((unsigned long)(n))>>16)&0x7) +#define DDR0_05_TRP_MASK 0x00000F00 +#define DDR0_05_TRP_ENCODE(n) ((((unsigned long)(n))&0xF)<<8) +#define DDR0_05_TRP_DECODE(n) ((((unsigned long)(n))>>8)&0xF) +#define DDR0_05_TRAS_MIN_MASK 0x000000FF +#define DDR0_05_TRAS_MIN_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0) +#define DDR0_05_TRAS_MIN_DECODE(n) ((((unsigned long)(n))>>0)&0xFF) + +#define DDR0_06 0x06 +#define DDR0_06_WRITEINTERP_MASK 0x01000000 +#define DDR0_06_WRITEINTERP_ENCODE(n) ((((unsigned long)(n))&0x1)<<24) +#define DDR0_06_WRITEINTERP_DECODE(n) ((((unsigned long)(n))>>24)&0x1) +#define DDR0_06_TWTR_MASK 0x00070000 +#define DDR0_06_TWTR_ENCODE(n) ((((unsigned long)(n))&0x7)<<16) +#define DDR0_06_TWTR_DECODE(n) ((((unsigned long)(n))>>16)&0x7) +#define DDR0_06_TDLL_MASK 0x0000FF00 +#define DDR0_06_TDLL_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8) +#define DDR0_06_TDLL_DECODE(n) ((((unsigned long)(n))>>8)&0xFF) +#define DDR0_06_TRFC_MASK 0x0000007F +#define DDR0_06_TRFC_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_06_TRFC_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_07 0x07 +#define DDR0_07_NO_CMD_INIT_MASK 0x01000000 +#define DDR0_07_NO_CMD_INIT_ENCODE(n) ((((unsigned long)(n))&0x1)<<24) +#define DDR0_07_NO_CMD_INIT_DECODE(n) ((((unsigned long)(n))>>24)&0x1) +#define DDR0_07_TFAW_MASK 0x001F0000 +#define DDR0_07_TFAW_ENCODE(n) ((((unsigned long)(n))&0x1F)<<16) +#define DDR0_07_TFAW_DECODE(n) ((((unsigned long)(n))>>16)&0x1F) +#define DDR0_07_AUTO_REFRESH_MODE_MASK 0x00000100 +#define DDR0_07_AUTO_REFRESH_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<8) +#define DDR0_07_AUTO_REFRESH_MODE_DECODE(n) ((((unsigned long)(n))>>8)&0x1) +#define DDR0_07_AREFRESH_MASK 0x00000001 +#define DDR0_07_AREFRESH_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_07_AREFRESH_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_08 0x08 +#define DDR0_08_WRLAT_MASK 0x07000000 +#define DDR0_08_WRLAT_ENCODE(n) ((((unsigned long)(n))&0x7)<<24) +#define DDR0_08_WRLAT_DECODE(n) ((((unsigned long)(n))>>24)&0x7) +#define DDR0_08_TCPD_MASK 0x00FF0000 +#define DDR0_08_TCPD_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16) +#define DDR0_08_TCPD_DECODE(n) ((((unsigned long)(n))>>16)&0xFF) +#define DDR0_08_DQS_N_EN_MASK 0x00000100 +#define DDR0_08_DQS_N_EN_ENCODE(n) ((((unsigned long)(n))&0x1)<<8) +#define DDR0_08_DQS_N_EN_DECODE(n) ((((unsigned long)(n))>>8)&0x1) +#define DDR0_08_DDRII_SDRAM_MODE_MASK 0x00000001 +#define DDR0_08_DDRII_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_08_DDRII_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_09 0x09 +#define DDR0_09_OCD_ADJUST_PDN_CS_0_MASK 0x1F000000 +#define DDR0_09_OCD_ADJUST_PDN_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<24) +#define DDR0_09_OCD_ADJUST_PDN_CS_0_DECODE(n) ((((unsigned long)(n))>>24)&0x1F) +#define DDR0_09_RTT_0_MASK 0x00030000 +#define DDR0_09_RTT_0_ENCODE(n) ((((unsigned long)(n))&0x3)<<16) +#define DDR0_09_RTT_0_DECODE(n) ((((unsigned long)(n))>>16)&0x3) +#define DDR0_09_WR_DQS_SHIFT_BYPASS_MASK 0x00007F00 +#define DDR0_09_WR_DQS_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_09_WR_DQS_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_09_WR_DQS_SHIFT_MASK 0x0000007F +#define DDR0_09_WR_DQS_SHIFT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_09_WR_DQS_SHIFT_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_10 0x0A +#define DDR0_10_WRITE_MODEREG_MASK 0x00010000 /* Write only */ +#define DDR0_10_WRITE_MODEREG_ENCODE(n) ((((unsigned long)(n))&0x1)<<16) +#define DDR0_10_WRITE_MODEREG_DECODE(n) ((((unsigned long)(n))>>16)&0x1) +#define DDR0_10_CS_MAP_MASK 0x00000300 +#define DDR0_10_CS_MAP_NO_MEM 0x00000000 +#define DDR0_10_CS_MAP_RANK0_INSTALLED 0x00000100 +#define DDR0_10_CS_MAP_RANK1_INSTALLED 0x00000200 +#define DDR0_10_CS_MAP_ENCODE(n) ((((unsigned long)(n))&0x3)<<8) +#define DDR0_10_CS_MAP_DECODE(n) ((((unsigned long)(n))>>8)&0x3) +#define DDR0_10_OCD_ADJUST_PUP_CS_0_MASK 0x0000001F +#define DDR0_10_OCD_ADJUST_PUP_CS_0_ENCODE(n) ((((unsigned long)(n))&0x1F)<<0) +#define DDR0_10_OCD_ADJUST_PUP_CS_0_DECODE(n) ((((unsigned long)(n))>>0)&0x1F) + +#define DDR0_11 0x0B +#define DDR0_11_SREFRESH_MASK 0x01000000 +#define DDR0_11_SREFRESH_ENCODE(n) ((((unsigned long)(n))&0x1)<<24) +#define DDR0_11_SREFRESH_DECODE(n) ((((unsigned long)(n))>>24)&0x1F) +#define DDR0_11_TXSNR_MASK 0x00FF0000 +#define DDR0_11_TXSNR_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16) +#define DDR0_11_TXSNR_DECODE(n) ((((unsigned long)(n))>>16)&0xFF) +#define DDR0_11_TXSR_MASK 0x0000FF00 +#define DDR0_11_TXSR_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8) +#define DDR0_11_TXSR_DECODE(n) ((((unsigned long)(n))>>8)&0xFF) + +#define DDR0_12 0x0C +#define DDR0_12_TCKE_MASK 0x0000007 +#define DDR0_12_TCKE_ENCODE(n) ((((unsigned long)(n))&0x7)<<0) +#define DDR0_12_TCKE_DECODE(n) ((((unsigned long)(n))>>0)&0x7) + +#define DDR0_14 0x0E +#define DDR0_14_DLL_BYPASS_MODE_MASK 0x01000000 +#define DDR0_14_DLL_BYPASS_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<24) +#define DDR0_14_DLL_BYPASS_MODE_DECODE(n) ((((unsigned long)(n))>>24)&0x1) +#define DDR0_14_REDUC_MASK 0x00010000 +#define DDR0_14_REDUC_64BITS 0x00000000 +#define DDR0_14_REDUC_32BITS 0x00010000 +#define DDR0_14_REDUC_ENCODE(n) ((((unsigned long)(n))&0x1)<<16) +#define DDR0_14_REDUC_DECODE(n) ((((unsigned long)(n))>>16)&0x1) +#define DDR0_14_REG_DIMM_ENABLE_MASK 0x00000100 +#define DDR0_14_REG_DIMM_ENABLE_ENCODE(n) ((((unsigned long)(n))&0x1)<<8) +#define DDR0_14_REG_DIMM_ENABLE_DECODE(n) ((((unsigned long)(n))>>8)&0x1) + +#define DDR0_17 0x11 +#define DDR0_17_DLL_DQS_DELAY_0_MASK 0x7F000000 +#define DDR0_17_DLL_DQS_DELAY_0_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_17_DLL_DQS_DELAY_0_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +#define DDR0_17_DLLLOCKREG_MASK 0x00010000 /* Read only */ +#define DDR0_17_DLLLOCKREG_LOCKED 0x00010000 +#define DDR0_17_DLLLOCKREG_UNLOCKED 0x00000000 +#define DDR0_17_DLLLOCKREG_ENCODE(n) ((((unsigned long)(n))&0x1)<<16) +#define DDR0_17_DLLLOCKREG_DECODE(n) ((((unsigned long)(n))>>16)&0x1) +#define DDR0_17_DLL_LOCK_MASK 0x00007F00 /* Read only */ +#define DDR0_17_DLL_LOCK_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_17_DLL_LOCK_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) + +#define DDR0_18 0x12 +#define DDR0_18_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F +#define DDR0_18_DLL_DQS_DELAY_4_MASK 0x7F000000 +#define DDR0_18_DLL_DQS_DELAY_4_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_18_DLL_DQS_DELAY_4_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +#define DDR0_18_DLL_DQS_DELAY_3_MASK 0x007F0000 +#define DDR0_18_DLL_DQS_DELAY_3_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define DDR0_18_DLL_DQS_DELAY_3_DECODE(n) ((((unsigned long)(n))>>16)&0x7F) +#define DDR0_18_DLL_DQS_DELAY_2_MASK 0x00007F00 +#define DDR0_18_DLL_DQS_DELAY_2_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_18_DLL_DQS_DELAY_2_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_18_DLL_DQS_DELAY_1_MASK 0x0000007F +#define DDR0_18_DLL_DQS_DELAY_1_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_18_DLL_DQS_DELAY_1_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_19 0x13 +#define DDR0_19_DLL_DQS_DELAY_X_MASK 0x7F7F7F7F +#define DDR0_19_DLL_DQS_DELAY_8_MASK 0x7F000000 +#define DDR0_19_DLL_DQS_DELAY_8_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_19_DLL_DQS_DELAY_8_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +#define DDR0_19_DLL_DQS_DELAY_7_MASK 0x007F0000 +#define DDR0_19_DLL_DQS_DELAY_7_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define DDR0_19_DLL_DQS_DELAY_7_DECODE(n) ((((unsigned long)(n))>>16)&0x7F) +#define DDR0_19_DLL_DQS_DELAY_6_MASK 0x00007F00 +#define DDR0_19_DLL_DQS_DELAY_6_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_19_DLL_DQS_DELAY_6_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_19_DLL_DQS_DELAY_5_MASK 0x0000007F +#define DDR0_19_DLL_DQS_DELAY_5_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_19_DLL_DQS_DELAY_5_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_20 0x14 +#define DDR0_20_DLL_DQS_BYPASS_3_MASK 0x7F000000 +#define DDR0_20_DLL_DQS_BYPASS_3_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_20_DLL_DQS_BYPASS_3_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +#define DDR0_20_DLL_DQS_BYPASS_2_MASK 0x007F0000 +#define DDR0_20_DLL_DQS_BYPASS_2_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define DDR0_20_DLL_DQS_BYPASS_2_DECODE(n) ((((unsigned long)(n))>>16)&0x7F) +#define DDR0_20_DLL_DQS_BYPASS_1_MASK 0x00007F00 +#define DDR0_20_DLL_DQS_BYPASS_1_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_20_DLL_DQS_BYPASS_1_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_20_DLL_DQS_BYPASS_0_MASK 0x0000007F +#define DDR0_20_DLL_DQS_BYPASS_0_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_20_DLL_DQS_BYPASS_0_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_21 0x15 +#define DDR0_21_DLL_DQS_BYPASS_7_MASK 0x7F000000 +#define DDR0_21_DLL_DQS_BYPASS_7_ENCODE(n) ((((unsigned long)(n))&0x7F)<<24) +#define DDR0_21_DLL_DQS_BYPASS_7_DECODE(n) ((((unsigned long)(n))>>24)&0x7F) +#define DDR0_21_DLL_DQS_BYPASS_6_MASK 0x007F0000 +#define DDR0_21_DLL_DQS_BYPASS_6_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define DDR0_21_DLL_DQS_BYPASS_6_DECODE(n) ((((unsigned long)(n))>>16)&0x7F) +#define DDR0_21_DLL_DQS_BYPASS_5_MASK 0x00007F00 +#define DDR0_21_DLL_DQS_BYPASS_5_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_21_DLL_DQS_BYPASS_5_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_21_DLL_DQS_BYPASS_4_MASK 0x0000007F +#define DDR0_21_DLL_DQS_BYPASS_4_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_21_DLL_DQS_BYPASS_4_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_22 0x16 +#define DDR0_22_CTRL_RAW_MASK 0x03000000 +#define DDR0_22_CTRL_RAW_ECC_DISABLE 0x00000000 /* ECC not being used */ +#define DDR0_22_CTRL_RAW_ECC_CHECK_ONLY 0x01000000 /* ECC checking is on, but no attempts to correct */ +#define DDR0_22_CTRL_RAW_NO_ECC_RAM 0x02000000 /* No ECC RAM storage available */ +#define DDR0_22_CTRL_RAW_ECC_ENABLE 0x03000000 /* ECC checking and correcting on */ +#define DDR0_22_CTRL_RAW_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define DDR0_22_CTRL_RAW_DECODE(n) ((((unsigned long)(n))>>24)&0x3) +#define DDR0_22_DQS_OUT_SHIFT_BYPASS_MASK 0x007F0000 +#define DDR0_22_DQS_OUT_SHIFT_BYPASS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) +#define DDR0_22_DQS_OUT_SHIFT_BYPASS_DECODE(n) ((((unsigned long)(n))>>16)&0x7F) +#define DDR0_22_DQS_OUT_SHIFT_MASK 0x00007F00 +#define DDR0_22_DQS_OUT_SHIFT_ENCODE(n) ((((unsigned long)(n))&0x7F)<<8) +#define DDR0_22_DQS_OUT_SHIFT_DECODE(n) ((((unsigned long)(n))>>8)&0x7F) +#define DDR0_22_DLL_DQS_BYPASS_8_MASK 0x0000007F +#define DDR0_22_DLL_DQS_BYPASS_8_ENCODE(n) ((((unsigned long)(n))&0x7F)<<0) +#define DDR0_22_DLL_DQS_BYPASS_8_DECODE(n) ((((unsigned long)(n))>>0)&0x7F) + +#define DDR0_23 0x17 +#define DDR0_23_ODT_RD_MAP_CS0_MASK 0x03000000 +#define DDR0_23_ODT_RD_MAP_CS0_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define DDR0_23_ODT_RD_MAP_CS0_DECODE(n) ((((unsigned long)(n))>>24)&0x3) +#define DDR0_23_ECC_C_SYND_MASK 0x00FF0000 /* Read only */ +#define DDR0_23_ECC_C_SYND_ENCODE(n) ((((unsigned long)(n))&0xFF)<<16) +#define DDR0_23_ECC_C_SYND_DECODE(n) ((((unsigned long)(n))>>16)&0xFF) +#define DDR0_23_ECC_U_SYND_MASK 0x0000FF00 /* Read only */ +#define DDR0_23_ECC_U_SYND_ENCODE(n) ((((unsigned long)(n))&0xFF)<<8) +#define DDR0_23_ECC_U_SYND_DECODE(n) ((((unsigned long)(n))>>8)&0xFF) +#define DDR0_23_FWC_MASK 0x00000001 /* Write only */ +#define DDR0_23_FWC_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_23_FWC_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_24 0x18 +#define DDR0_24_RTT_PAD_TERMINATION_MASK 0x03000000 +#define DDR0_24_RTT_PAD_TERMINATION_ENCODE(n) ((((unsigned long)(n))&0x3)<<24) +#define DDR0_24_RTT_PAD_TERMINATION_DECODE(n) ((((unsigned long)(n))>>24)&0x3) +#define DDR0_24_ODT_WR_MAP_CS1_MASK 0x00030000 +#define DDR0_24_ODT_WR_MAP_CS1_ENCODE(n) ((((unsigned long)(n))&0x3)<<16) +#define DDR0_24_ODT_WR_MAP_CS1_DECODE(n) ((((unsigned long)(n))>>16)&0x3) +#define DDR0_24_ODT_RD_MAP_CS1_MASK 0x00000300 +#define DDR0_24_ODT_RD_MAP_CS1_ENCODE(n) ((((unsigned long)(n))&0x3)<<8) +#define DDR0_24_ODT_RD_MAP_CS1_DECODE(n) ((((unsigned long)(n))>>8)&0x3) +#define DDR0_24_ODT_WR_MAP_CS0_MASK 0x00000003 +#define DDR0_24_ODT_WR_MAP_CS0_ENCODE(n) ((((unsigned long)(n))&0x3)<<0) +#define DDR0_24_ODT_WR_MAP_CS0_DECODE(n) ((((unsigned long)(n))>>0)&0x3) + +#define DDR0_25 0x19 +#define DDR0_25_VERSION_MASK 0xFFFF0000 /* Read only */ +#define DDR0_25_VERSION_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) +#define DDR0_25_VERSION_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) +#define DDR0_25_OUT_OF_RANGE_LENGTH_MASK 0x000003FF /* Read only */ +#define DDR0_25_OUT_OF_RANGE_LENGTH_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) +#define DDR0_25_OUT_OF_RANGE_LENGTH_DECODE(n) ((((unsigned long)(n))>>0)&0x3FF) + +#define DDR0_26 0x1A +#define DDR0_26_TRAS_MAX_MASK 0xFFFF0000 +#define DDR0_26_TRAS_MAX_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<16) +#define DDR0_26_TRAS_MAX_DECODE(n) ((((unsigned long)(n))>>16)&0xFFFF) +#define DDR0_26_TREF_MASK 0x00003FFF +#define DDR0_26_TREF_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0) +#define DDR0_26_TREF_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF) + +#define DDR0_27 0x1B +#define DDR0_27_EMRS_DATA_MASK 0x3FFF0000 +#define DDR0_27_EMRS_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<16) +#define DDR0_27_EMRS_DATA_DECODE(n) ((((unsigned long)(n))>>16)&0x3FFF) +#define DDR0_27_TINIT_MASK 0x0000FFFF +#define DDR0_27_TINIT_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<0) +#define DDR0_27_TINIT_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFF) + +#define DDR0_28 0x1C +#define DDR0_28_EMRS3_DATA_MASK 0x3FFF0000 +#define DDR0_28_EMRS3_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<16) +#define DDR0_28_EMRS3_DATA_DECODE(n) ((((unsigned long)(n))>>16)&0x3FFF) +#define DDR0_28_EMRS2_DATA_MASK 0x00003FFF +#define DDR0_28_EMRS2_DATA_ENCODE(n) ((((unsigned long)(n))&0x3FFF)<<0) +#define DDR0_28_EMRS2_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0x3FFF) + +#define DDR0_31 0x1F +#define DDR0_31_XOR_CHECK_BITS_MASK 0x0000FFFF +#define DDR0_31_XOR_CHECK_BITS_ENCODE(n) ((((unsigned long)(n))&0xFFFF)<<0) +#define DDR0_31_XOR_CHECK_BITS_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFF) + +#define DDR0_32 0x20 +#define DDR0_32_OUT_OF_RANGE_ADDR_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_32_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_32_OUT_OF_RANGE_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_33 0x21 +#define DDR0_33_OUT_OF_RANGE_ADDR_MASK 0x00000001 /* Read only */ +#define DDR0_33_OUT_OF_RANGE_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_33_OUT_OF_RANGE_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_34 0x22 +#define DDR0_34_ECC_U_ADDR_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_34_ECC_U_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_34_ECC_U_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_35 0x23 +#define DDR0_35_ECC_U_ADDR_MASK 0x00000001 /* Read only */ +#define DDR0_35_ECC_U_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_35_ECC_U_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_36 0x24 +#define DDR0_36_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_36_ECC_U_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_36_ECC_U_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_37 0x25 +#define DDR0_37_ECC_U_DATA_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_37_ECC_U_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_37_ECC_U_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_38 0x26 +#define DDR0_38_ECC_C_ADDR_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_38_ECC_C_ADDR_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_38_ECC_C_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_39 0x27 +#define DDR0_39_ECC_C_ADDR_MASK 0x00000001 /* Read only */ +#define DDR0_39_ECC_C_ADDR_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_39_ECC_C_ADDR_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_40 0x28 +#define DDR0_40_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_40_ECC_C_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_40_ECC_C_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_41 0x29 +#define DDR0_41_ECC_C_DATA_MASK 0xFFFFFFFF /* Read only */ +#define DDR0_41_ECC_C_DATA_ENCODE(n) ((((unsigned long)(n))&0xFFFFFFFF)<<0) +#define DDR0_41_ECC_C_DATA_DECODE(n) ((((unsigned long)(n))>>0)&0xFFFFFFFF) + +#define DDR0_42 0x2A +#define DDR0_42_ADDR_PINS_MASK 0x07000000 +#define DDR0_42_ADDR_PINS_ENCODE(n) ((((unsigned long)(n))&0x7)<<24) +#define DDR0_42_ADDR_PINS_DECODE(n) ((((unsigned long)(n))>>24)&0x7) +#define DDR0_42_CASLAT_LIN_GATE_MASK 0x0000000F +#define DDR0_42_CASLAT_LIN_GATE_ENCODE(n) ((((unsigned long)(n))&0xF)<<0) +#define DDR0_42_CASLAT_LIN_GATE_DECODE(n) ((((unsigned long)(n))>>0)&0xF) + +#define DDR0_43 0x2B +#define DDR0_43_TWR_MASK 0x07000000 +#define DDR0_43_TWR_ENCODE(n) ((((unsigned long)(n))&0x7)<<24) +#define DDR0_43_TWR_DECODE(n) ((((unsigned long)(n))>>24)&0x7) +#define DDR0_43_APREBIT_MASK 0x000F0000 +#define DDR0_43_APREBIT_ENCODE(n) ((((unsigned long)(n))&0xF)<<16) +#define DDR0_43_APREBIT_DECODE(n) ((((unsigned long)(n))>>16)&0xF) +#define DDR0_43_COLUMN_SIZE_MASK 0x00000700 +#define DDR0_43_COLUMN_SIZE_ENCODE(n) ((((unsigned long)(n))&0x7)<<8) +#define DDR0_43_COLUMN_SIZE_DECODE(n) ((((unsigned long)(n))>>8)&0x7) +#define DDR0_43_EIGHT_BANK_MODE_MASK 0x00000001 +#define DDR0_43_EIGHT_BANK_MODE_8_BANKS 0x00000001 +#define DDR0_43_EIGHT_BANK_MODE_4_BANKS 0x00000000 +#define DDR0_43_EIGHT_BANK_MODE_ENCODE(n) ((((unsigned long)(n))&0x1)<<0) +#define DDR0_43_EIGHT_BANK_MODE_DECODE(n) ((((unsigned long)(n))>>0)&0x1) + +#define DDR0_44 0x2C +#define DDR0_44_TRCD_MASK 0x000000FF +#define DDR0_44_TRCD_ENCODE(n) ((((unsigned long)(n))&0xFF)<<0) +#define DDR0_44_TRCD_DECODE(n) ((((unsigned long)(n))>>0)&0xFF) + +#endif /* CONFIG_440EPX */ + /*----------------------------------------------------------------------------- | External Bus Controller +----------------------------------------------------------------------------*/ -- cgit v1.3.1 From 87dc096829e6a6363f4fdd73653b0093a85adbe0 Mon Sep 17 00:00:00 2001 From: Larry Johnson Date: Sat, 22 Dec 2007 15:16:25 -0500 Subject: Add configuration file for Korat board This patch supplies the configuration file for the Korat PPC440EPx- processor board. Signed-off-by: Larry Johnson --- include/configs/korat.h | 376 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 376 insertions(+) create mode 100644 include/configs/korat.h (limited to 'include') diff --git a/include/configs/korat.h b/include/configs/korat.h new file mode 100644 index 00000000000..1ea7d4894aa --- /dev/null +++ b/include/configs/korat.h @@ -0,0 +1,376 @@ +/* + * (C) Copyright 2007 + * Larry Johnson, lrj@acm.org + * + * (C) Copyright 2006-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * korat.h - configuration for Korat board + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 33333333 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/*----------------------------------------------------------------------- + * Manufacturer's information serial EEPROM parameters + *----------------------------------------------------------------------*/ +#define MAN_DATA_EEPROM_ADDR 0x53 /* EEPROM I2C address */ +#define MAN_SERIAL_NO_FIELD 2 +#define MAN_SERIAL_NO_LENGTH 13 +#define MAN_MAC_ADDR_FIELD 3 +#define MAN_MAC_ADDR_LENGTH 17 + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ + +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_OCM_BASE 0xe0010000 /* ocm */ +#define CFG_OCM_DATA_ADDR CFG_OCM_BASE +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 + +/* Don't change either of these */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ + +#define CFG_USB2D0_BASE 0xe0000100 +#define CFG_USB_DEVICE 0xe0000000 +#define CFG_USB_HOST 0xe0000400 +#define CFG_CPLD_BASE 0xc0000000 + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +/* 440EPx has 16KB of internal SRAM, so no need for D-Cache */ +#undef CFG_INIT_RAM_DCACHE +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#undef CONFIG_UART1_CONSOLE + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environ vars */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM (512) /* 512 MiB TODO: remove */ +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ +#define CONFIG_ZERO_SDRAM /* Zero SDRAM after setup */ +#define CONFIG_DDR_ECC /* Use ECC when available */ +#define SPD_EEPROM_ADDRESS {0x50} +#define CONFIG_PROG_SDRAM_TLB +#define CFG_DRAM_TEST + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0xa8>>1) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* I2C RTC */ +#define CONFIG_RTC_M41T60 1 +#define CFG_I2C_RTC_ADDR 0x68 + +/* I2C SYSMON (LM73) */ +#define CONFIG_DTT_LM73 1 /* National Semi's LM73 */ +#define CONFIG_DTT_SENSORS {2} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_MIN_TEMP -30 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +/* Setup some board specific values for the default environment variables */ +#define CONFIG_HOSTNAME korat +#define CFG_BOOTFILE "bootfile=/tftpboot/korat/uImage\0" +#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CFG_BOOTFILE \ + CFG_ROOTPATH \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ + "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ + "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ + "cp.b 200000 FFFA0000 60000\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ +#define CONFIG_PHY_DYNAMIC_ANEG 1 + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 3 + +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* Comment this out to enable USB 1.1 device */ +#define USB_2_0_DEVICE + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_SUBNETMASK + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DTT +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_I2C_CMD_TREE +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_USB + +/* POST support */ +#define CONFIG_POST (CFG_POST_CACHE | \ + CFG_POST_CPU | \ + CFG_POST_ECC | \ + CFG_POST_ETHER | \ + CFG_POST_FPU | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_RTC | \ + CFG_POST_SPR | \ + CFG_POST_UART) + +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CONFIG_LOGBUFFER +#define CFG_POST_CACHE_ADDR 0xC8000000 /* free virtual address */ + +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +#define CONFIG_SUPPORT_VFAT + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ + +/* Board-specific PCI */ +#define CFG_PCI_TARGET_INIT +#define CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x04017300 +#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0x000DA000) + +/* Memory Bank 1 (NOR-FLASH) initialization */ +#define CFG_EBC_PB1AP 0x04017300 +#define CFG_EBC_PB1CR (0xF8000000 | 0x000DA000) + +/* Memory Bank 2 (CPLD) initialization */ +#define CFG_EBC_PB2AP 0x04017300 +#define CFG_EBC_PB2CR (CFG_CPLD_BASE | 0x00038000) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ -- cgit v1.3.1 From b568fd25574181a3b12ae3d66b2913903442cb83 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Thu, 27 Dec 2007 17:03:46 +0100 Subject: Remove CPCI440 board This board never left prototyping state and it became a millstone round my neck. So remove it. Signed-off-by: Matthias Fuchs --- MAINTAINERS | 1 - MAKEALL | 1 - Makefile | 3 - board/esd/cpci440/Makefile | 54 --- board/esd/cpci440/config.mk | 45 --- board/esd/cpci440/cpci440.c | 152 -------- board/esd/cpci440/init.S | 94 ----- board/esd/cpci440/strataflash.c | 755 ---------------------------------------- board/esd/cpci440/u-boot.lds | 159 --------- include/configs/CPCI440.h | 287 --------------- 10 files changed, 1551 deletions(-) delete mode 100644 board/esd/cpci440/Makefile delete mode 100644 board/esd/cpci440/config.mk delete mode 100644 board/esd/cpci440/cpci440.c delete mode 100644 board/esd/cpci440/init.S delete mode 100644 board/esd/cpci440/strataflash.c delete mode 100644 board/esd/cpci440/u-boot.lds delete mode 100644 include/configs/CPCI440.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 0238d2e8163..6e3c2ef499f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -146,7 +146,6 @@ Matthias Fuchs CPCI4052 PPC405GP CPCI405AB PPC405GP CPCI405DT PPC405GP - CPCI440 PPC440GP CPCIISER4 PPC405GP DASA_SIM IOP480 (PPC401) DP405 PPC405EP diff --git a/MAKEALL b/MAKEALL index 97e389172a8..a6e0eef1652 100755 --- a/MAKEALL +++ b/MAKEALL @@ -168,7 +168,6 @@ LIST_4xx=" \ CPCI4052 \ CPCI405AB \ CPCI405DT \ - CPCI440 \ CPCIISER4 \ CRAYL1 \ csb272 \ diff --git a/Makefile b/Makefile index c127bcfb94d..e5d69b4fc11 100644 --- a/Makefile +++ b/Makefile @@ -1160,9 +1160,6 @@ CPCI405AB_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci405 esd @echo "BOARD_REVISION = $(@:_config=)" >> $(obj)include/config.mk -CPCI440_config: unconfig - @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpci440 esd - CPCIISER4_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx cpciiser4 esd diff --git a/board/esd/cpci440/Makefile b/board/esd/cpci440/Makefile deleted file mode 100644 index d13d31c9748..00000000000 --- a/board/esd/cpci440/Makefile +++ /dev/null @@ -1,54 +0,0 @@ -# -# (C) Copyright 2002-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk -ifneq ($(OBJTREE),$(SRCTREE)) -$(shell mkdir -p $(obj)../common) -endif - -LIB = $(obj)lib$(BOARD).a - -COBJS = $(BOARD).o strataflash.o ../common/misc.o -SOBJS = init.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(OBJS) $(SOBJS) - $(AR) $(ARFLAGS) $@ $(OBJS) - -clean: - rm -f $(SOBJS) $(OBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/esd/cpci440/config.mk b/board/esd/cpci440/config.mk deleted file mode 100644 index 8e5f63fe489..00000000000 --- a/board/esd/cpci440/config.mk +++ /dev/null @@ -1,45 +0,0 @@ -# -# (C) Copyright 2002 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -# -# esd ADCIOP boards -# - -#TEXT_BASE = 0xFFFE0000 - -ifeq ($(ramsym),1) -TEXT_BASE = 0x07FD0000 -else -TEXT_BASE = 0xFFFC0000 -#TEXT_BASE = 0x01fc0000 -endif - -PLATFORM_CPPFLAGS += -DCONFIG_440=1 - -ifeq ($(debug),1) -PLATFORM_CPPFLAGS += -DDEBUG -endif - -ifeq ($(dbcr),1) -PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000 -endif diff --git a/board/esd/cpci440/cpci440.c b/board/esd/cpci440/cpci440.c deleted file mode 100644 index caa6d5591fd..00000000000 --- a/board/esd/cpci440/cpci440.c +++ /dev/null @@ -1,152 +0,0 @@ -/* - * (C) Copyright 2002 - * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#include - - -extern void lxt971_no_sleep(void); - - -long int fixed_sdram( void ); - -int board_early_init_f (void) -{ - uint reg; - - /*-------------------------------------------------------------------- - * Setup the external bus controller/chip selects - *-------------------------------------------------------------------*/ - mtdcr( ebccfga, xbcfg ); - reg = mfdcr( ebccfgd ); - mtdcr( ebccfgd, reg | 0x04000000 ); /* Set ATC */ - - mtebc( pb0ap, 0x92015480 ); /* FLASH/SRAM */ - mtebc( pb0cr, 0xFF87A000 ); /* BAS=0xff8 8MB R/W 16-bit */ - /* test-only: other regs still missing... */ - - /*-------------------------------------------------------------------- - * Setup the interrupt controller polarities, triggers, etc. - *-------------------------------------------------------------------*/ - mtdcr( uic0sr, 0xffffffff ); /* clear all */ - mtdcr( uic0er, 0x00000000 ); /* disable all */ - mtdcr( uic0cr, 0x00000009 ); /* SMI & UIC1 crit are critical */ - mtdcr( uic0pr, 0xfffffe13 ); /* per ref-board manual */ - mtdcr( uic0tr, 0x01c00008 ); /* per ref-board manual */ - mtdcr( uic0vr, 0x00000001 ); /* int31 highest, base=0x000 */ - mtdcr( uic0sr, 0xffffffff ); /* clear all */ - - mtdcr( uic1sr, 0xffffffff ); /* clear all */ - mtdcr( uic1er, 0x00000000 ); /* disable all */ - mtdcr( uic1cr, 0x00000000 ); /* all non-critical */ - mtdcr( uic1pr, 0xffffe0ff ); /* per ref-board manual */ - mtdcr( uic1tr, 0x00ffc000 ); /* per ref-board manual */ - mtdcr( uic1vr, 0x00000001 ); /* int31 highest, base=0x000 */ - mtdcr( uic1sr, 0xffffffff ); /* clear all */ - - return 0; -} - - -int checkboard (void) -{ - sys_info_t sysinfo; - get_sys_info(&sysinfo); - - printf("Board: esd CPCI-440\n"); - printf("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz/1000000); - printf("\tCPU: %lu MHz\n", sysinfo.freqProcessor/1000000); - printf("\tPLB: %lu MHz\n", sysinfo.freqPLB/1000000); - printf("\tOPB: %lu MHz\n", sysinfo.freqOPB/1000000); - printf("\tEBC: %lu MHz\n", sysinfo.freqEBC/1000000); - - /* - * Disable sleep mode in LXT971 - */ - lxt971_no_sleep(); - - return (0); -} - - -long int initdram (int board_type) -{ - long dram_size = 0; - - dram_size = fixed_sdram(); - return dram_size; -} - - -/************************************************************************* - * fixed sdram init -- doesn't use serial presence detect. - * - * Assumes: 64 MB, non-ECC, non-registered - * PLB @ 133 MHz - * - ************************************************************************/ -long int fixed_sdram( void ) -{ - uint reg; - -#if 1 /* test-only */ - /*-------------------------------------------------------------------- - * Setup some default - *------------------------------------------------------------------*/ - mtsdram( mem_uabba, 0x00000000 ); /* ubba=0 (default) */ - mtsdram( mem_slio, 0x00000000 ); /* rdre=0 wrre=0 rarw=0 */ - mtsdram( mem_devopt,0x00000000 ); /* dll=0 ds=0 (normal) */ - mtsdram( mem_wddctr,0x40000000 ); /* wrcp=0 dcd=0 */ - mtsdram( mem_clktr, 0x40000000 ); /* clkp=1 (90 deg wr) dcdt=0 */ - - /*-------------------------------------------------------------------- - * Setup for board-specific specific mem - *------------------------------------------------------------------*/ - /* - * Following for CAS Latency = 2.5 @ 133 MHz PLB - */ - mtsdram( mem_b0cr, 0x00082001 );/* SDBA=0x000, 64MB, Mode 2, enabled*/ - mtsdram( mem_tr0, 0x410a4012 );/* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */ - /* RA=10 RD=3 */ - mtsdram( mem_tr1, 0x8080082f );/* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */ - mtsdram( mem_rtr, 0x08200000 );/* Rate 15.625 ns @ 133 MHz PLB */ - mtsdram( mem_cfg1, 0x00000000 );/* Self-refresh exit, disable PM */ - udelay( 400 ); /* Delay 200 usecs (min) */ - - /*-------------------------------------------------------------------- - * Enable the controller, then wait for DCEN to complete - *------------------------------------------------------------------*/ - mtsdram( mem_cfg0, 0x86000000 );/* DCEN=1, PMUD=1, 64-bit */ - for(;;) - { - mfsdram( mem_mcsts, reg ); - if( reg & 0x80000000 ) - break; - } - - return( 64 * 1024 * 1024 ); /* 64 MB */ -#else - return( 32 * 1024 * 1024 ); /* 64 MB */ -#endif -} diff --git a/board/esd/cpci440/init.S b/board/esd/cpci440/init.S deleted file mode 100644 index 82f37fd9967..00000000000 --- a/board/esd/cpci440/init.S +++ /dev/null @@ -1,94 +0,0 @@ -/* -* Copyright (C) 2002 Scott McNutt -* -* See file CREDITS for list of people who contributed to this -* project. -* -* This program is free software; you can redistribute it and/or -* modify it under the terms of the GNU General Public License as -* published by the Free Software Foundation; either version 2 of -* the License, or (at your option) any later version. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License -* along with this program; if not, write to the Free Software -* Foundation, Inc., 59 Temple Place, Suite 330, Boston, -* MA 02111-1307 USA -*/ - -#include -#include - -/* General */ -#define TLB_VALID 0x00000200 - -/* Supported page sizes */ - -#define SZ_1K 0x00000000 -#define SZ_4K 0x00000010 -#define SZ_16K 0x00000020 -#define SZ_64K 0x00000030 -#define SZ_256K 0x00000040 -#define SZ_1M 0x00000050 -#define SZ_16M 0x00000070 -#define SZ_256M 0x00000090 - -/* Storage attributes */ -#define SA_W 0x00000800 /* Write-through */ -#define SA_I 0x00000400 /* Caching inhibited */ -#define SA_M 0x00000200 /* Memory coherence */ -#define SA_G 0x00000100 /* Guarded */ -#define SA_E 0x00000080 /* Endian */ - -/* Access control */ -#define AC_X 0x00000024 /* Execute */ -#define AC_W 0x00000012 /* Write */ -#define AC_R 0x00000009 /* Read */ - -/* Some handy macros */ - -#define EPN(e) ((e) & 0xfffffc00) -#define TLB0(epn,sz) ( (EPN((epn)) | (sz) | TLB_VALID ) ) -#define TLB1(rpn,erpn) ( ((rpn)&0xfffffc00) | (erpn) ) -#define TLB2(a) ( (a)&0x00000fbf ) - -#define tlbtab_start\ - mflr r1 ;\ - bl 0f ; - -#define tlbtab_end\ - .long 0, 0, 0 ; \ -0: mflr r0 ; \ - mtlr r1 ; \ - blr ; - -#define tlbentry(epn,sz,rpn,erpn,attr)\ - .long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr) - - -/************************************************************************** - * TLB TABLE - * - * This table is used by the cpu boot code to setup the initial tlb - * entries. Rather than make broad assumptions in the cpu source tree, - * this table lets each board set things up however they like. - * - * Pointer to the table is returned in r1 - * - *************************************************************************/ - - .section .bootpg,"ax" - .globl tlbtab - -tlbtab: - tlbtab_start - tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I) - tlbentry( CFG_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_R|AC_W|SA_G|SA_I) - tlbentry( CFG_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_R|AC_W|AC_X ) - tlbentry( CFG_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_R|AC_W|AC_X ) - tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X ) - tlbtab_end diff --git a/board/esd/cpci440/strataflash.c b/board/esd/cpci440/strataflash.c deleted file mode 100644 index 2f055c20d5b..00000000000 --- a/board/esd/cpci440/strataflash.c +++ /dev/null @@ -1,755 +0,0 @@ -/* - * (C) Copyright 2002 - * Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include - -#undef DEBUG_FLASH -/* - * This file implements a Common Flash Interface (CFI) driver for U-Boot. - * The width of the port and the width of the chips are determined at initialization. - * These widths are used to calculate the address for access CFI data structures. - * It has been tested on an Intel Strataflash implementation. - * - * References - * JEDEC Standard JESD68 - Common Flash Interface (CFI) - * JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes - * Intel Application Note 646 Common Flash Interface (CFI) and Command Sets - * Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet - * - * TODO - * Use Primary Extended Query table (PRI) and Alternate Algorithm Query Table (ALT) to determine if protection is available - * Add support for other command sets Use the PRI and ALT to determine command set - * Verify erase and program timeouts. - */ - -#define FLASH_CMD_CFI 0x98 -#define FLASH_CMD_READ_ID 0x90 -#define FLASH_CMD_RESET 0xff -#define FLASH_CMD_BLOCK_ERASE 0x20 -#define FLASH_CMD_ERASE_CONFIRM 0xD0 -#define FLASH_CMD_WRITE 0x40 -#define FLASH_CMD_PROTECT 0x60 -#define FLASH_CMD_PROTECT_SET 0x01 -#define FLASH_CMD_PROTECT_CLEAR 0xD0 -#define FLASH_CMD_CLEAR_STATUS 0x50 -#define FLASH_CMD_WRITE_TO_BUFFER 0xE8 -#define FLASH_CMD_WRITE_BUFFER_CONFIRM 0xD0 - -#define FLASH_STATUS_DONE 0x80 -#define FLASH_STATUS_ESS 0x40 -#define FLASH_STATUS_ECLBS 0x20 -#define FLASH_STATUS_PSLBS 0x10 -#define FLASH_STATUS_VPENS 0x08 -#define FLASH_STATUS_PSS 0x04 -#define FLASH_STATUS_DPS 0x02 -#define FLASH_STATUS_R 0x01 -#define FLASH_STATUS_PROTECT 0x01 - -#define FLASH_OFFSET_CFI 0x55 -#define FLASH_OFFSET_CFI_RESP 0x10 -#define FLASH_OFFSET_WTOUT 0x1F -#define FLASH_OFFSET_WBTOUT 0x20 -#define FLASH_OFFSET_ETOUT 0x21 -#define FLASH_OFFSET_CETOUT 0x22 -#define FLASH_OFFSET_WMAX_TOUT 0x23 -#define FLASH_OFFSET_WBMAX_TOUT 0x24 -#define FLASH_OFFSET_EMAX_TOUT 0x25 -#define FLASH_OFFSET_CEMAX_TOUT 0x26 -#define FLASH_OFFSET_SIZE 0x27 -#define FLASH_OFFSET_INTERFACE 0x28 -#define FLASH_OFFSET_BUFFER_SIZE 0x2A -#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C -#define FLASH_OFFSET_ERASE_REGIONS 0x2D -#define FLASH_OFFSET_PROTECT 0x02 -#define FLASH_OFFSET_USER_PROTECTION 0x85 -#define FLASH_OFFSET_INTEL_PROTECTION 0x81 - - -#define FLASH_MAN_CFI 0x01000000 - - -typedef union { - unsigned char c; - unsigned short w; - unsigned long l; -} cfiword_t; - -typedef union { - unsigned char * cp; - unsigned short *wp; - unsigned long *lp; -} cfiptr_t; - -#define NUM_ERASE_REGIONS 4 - -flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */ - - -/*----------------------------------------------------------------------- - * Functions - */ - - -static void flash_add_byte(flash_info_t *info, cfiword_t * cword, uchar c); -static void flash_make_cmd(flash_info_t * info, uchar cmd, void * cmdbuf); -static void flash_write_cmd(flash_info_t * info, int sect, uchar offset, uchar cmd); -static int flash_isequal(flash_info_t * info, int sect, uchar offset, uchar cmd); -static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd); -static int flash_detect_cfi(flash_info_t * info); -static ulong flash_get_size (ulong base, int banknum); -static int flash_write_cfiword (flash_info_t *info, ulong dest, cfiword_t cword); -static int flash_full_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt); -#ifdef CFG_FLASH_USE_BUFFER_WRITE -static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp, int len); -#endif -/*----------------------------------------------------------------------- - * create an address based on the offset and the port width - */ -inline uchar * flash_make_addr(flash_info_t * info, int sect, int offset) -{ - return ((uchar *)(info->start[sect] + (offset * info->portwidth))); -} -/*----------------------------------------------------------------------- - * read a character at a port width address - */ -inline uchar flash_read_uchar(flash_info_t * info, uchar offset) -{ - uchar *cp; - cp = flash_make_addr(info, 0, offset); - return (cp[info->portwidth - 1]); -} - -/*----------------------------------------------------------------------- - * read a short word by swapping for ppc format. - */ -ushort flash_read_ushort(flash_info_t * info, int sect, uchar offset) -{ - uchar * addr; - - addr = flash_make_addr(info, sect, offset); - return ((addr[(2*info->portwidth) - 1] << 8) | addr[info->portwidth - 1]); - -} - -/*----------------------------------------------------------------------- - * read a long word by picking the least significant byte of each maiximum - * port size word. Swap for ppc format. - */ -ulong flash_read_long(flash_info_t * info, int sect, uchar offset) -{ - uchar * addr; - - addr = flash_make_addr(info, sect, offset); - return ( (addr[(2*info->portwidth) - 1] << 24 ) | (addr[(info->portwidth) -1] << 16) | - (addr[(4*info->portwidth) - 1] << 8) | addr[(3*info->portwidth) - 1]); - -} - -/*----------------------------------------------------------------------- - */ -unsigned long flash_init (void) -{ - unsigned long size; - int i; - unsigned long address; - - - /* The flash is positioned back to back, with the demultiplexing of the chip - * based on the A24 address line. - * - */ - - address = CFG_FLASH_BASE; - size = 0; - - /* Init: no FLASHes known */ - for (i=0; i= CFG_FLASH_BASE) - for(i=0; flash_info[0].start[i] < CFG_MONITOR_BASE+monitor_flash_len-1; i++) - (void)flash_real_protect(&flash_info[0], i, 1); -#endif -#endif - - return (size); -} - -/*----------------------------------------------------------------------- - */ -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - int rcode = 0; - int prot; - int sect; - - if( info->flash_id != FLASH_MAN_CFI) { - printf ("Can't erase unknown flash type - aborted\n"); - return 1; - } - if ((s_first < 0) || (s_first > s_last)) { - printf ("- no sectors to erase\n"); - return 1; - } - - prot = 0; - for (sect=s_first; sect<=s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - flash_write_cmd(info, sect, 0, FLASH_CMD_CLEAR_STATUS); - flash_write_cmd(info, sect, 0, FLASH_CMD_BLOCK_ERASE); - flash_write_cmd(info, sect, 0, FLASH_CMD_ERASE_CONFIRM); - - if(flash_full_status_check(info, sect, info->erase_blk_tout, "erase")) { - rcode = 1; - } else - printf("."); - } - } - printf (" done\n"); - return rcode; -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id != FLASH_MAN_CFI) { - printf ("missing or unknown FLASH type\n"); - return; - } - - printf("CFI conformant FLASH (%d x %d)", - (info->portwidth << 3 ), (info->chipwidth << 3 )); - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - printf(" Erase timeout %ld ms, write timeout %ld ms, buffer write timeout %ld ms, buffer size %d\n", - info->erase_blk_tout, info->write_tout, info->buffer_write_tout, info->buffer_size); - - printf (" Sector Start Addresses:"); - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) - printf ("\n"); - printf (" %08lX%5s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - ulong wp; - ulong cp; - int aln; - cfiword_t cword; - int i, rc; - - /* get lower aligned address */ - wp = (addr & ~(info->portwidth - 1)); - - /* handle unaligned start */ - if((aln = addr - wp) != 0) { - cword.l = 0; - cp = wp; - for(i=0;iportwidth) && (cnt > 0) ; i++) { - flash_add_byte(info, &cword, *src++); - cnt--; - cp++; - } - for(; (cnt == 0) && (i < info->portwidth); ++i, ++cp) - flash_add_byte(info, &cword, (*(uchar *)cp)); - if((rc = flash_write_cfiword(info, wp, cword)) != 0) - return rc; - wp = cp; - } - -#ifdef CFG_FLASH_USE_BUFFER_WRITE - while(cnt >= info->portwidth) { - i = info->buffer_size > cnt? cnt: info->buffer_size; - if((rc = flash_write_cfibuffer(info, wp, src,i)) != ERR_OK) - return rc; - wp += i; - src += i; - cnt -=i; - } -#else - /* handle the aligned part */ - while(cnt >= info->portwidth) { - cword.l = 0; - for(i = 0; i < info->portwidth; i++) { - flash_add_byte(info, &cword, *src++); - } - if((rc = flash_write_cfiword(info, wp, cword)) != 0) - return rc; - wp += info->portwidth; - cnt -= info->portwidth; - } -#endif /* CFG_FLASH_USE_BUFFER_WRITE */ - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - cword.l = 0; - for (i=0, cp=wp; (iportwidth) && (cnt>0); ++i, ++cp) { - flash_add_byte(info, &cword, *src++); - --cnt; - } - for (; iportwidth; ++i, ++cp) { - flash_add_byte(info, & cword, (*(uchar *)cp)); - } - - return flash_write_cfiword(info, wp, cword); -} - -/*----------------------------------------------------------------------- - */ -int flash_real_protect(flash_info_t *info, long sector, int prot) -{ - int retcode = 0; - - flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS); - flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT); - if(prot) - flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_SET); - else - flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_CLEAR); - - if((retcode = flash_full_status_check(info, sector, info->erase_blk_tout, - prot?"protect":"unprotect")) == 0) { - - info->protect[sector] = prot; - /* Intel's unprotect unprotects all locking */ - if(prot == 0) { - int i; - for(i = 0 ; isector_count; i++) { - if(info->protect[i]) - flash_real_protect(info, i, 1); - } - } - } - - return retcode; -} -/*----------------------------------------------------------------------- - * wait for XSR.7 to be set. Time out with an error if it does not. - * This routine does not set the flash to read-array mode. - */ -static int flash_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt) -{ - ulong start; - - /* Wait for command completion */ - start = get_timer (0); - while(!flash_isset(info, sector, 0, FLASH_STATUS_DONE)) { - if (get_timer(start) > info->erase_blk_tout) { - printf("Flash %s timeout at address %lx\n", prompt, info->start[sector]); - flash_write_cmd(info, sector, 0, FLASH_CMD_RESET); - return ERR_TIMOUT; - } - } - return ERR_OK; -} -/*----------------------------------------------------------------------- - * Wait for XSR.7 to be set, if it times out print an error, otherwise do a full status check. - * This routine sets the flash to read-array mode. - */ -static int flash_full_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt) -{ - int retcode; - retcode = flash_status_check(info, sector, tout, prompt); - if((retcode == ERR_OK) && !flash_isequal(info,sector, 0, FLASH_STATUS_DONE)) { - retcode = ERR_INVAL; - printf("Flash %s error at address %lx\n", prompt,info->start[sector]); - if(flash_isset(info, sector, 0, FLASH_STATUS_ECLBS | FLASH_STATUS_PSLBS)){ - printf("Command Sequence Error.\n"); - } else if(flash_isset(info, sector, 0, FLASH_STATUS_ECLBS)){ - printf("Block Erase Error.\n"); - retcode = ERR_NOT_ERASED; - } else if (flash_isset(info, sector, 0, FLASH_STATUS_PSLBS)) { - printf("Locking Error\n"); - } - if(flash_isset(info, sector, 0, FLASH_STATUS_DPS)){ - printf("Block locked.\n"); - retcode = ERR_PROTECTED; - } - if(flash_isset(info, sector, 0, FLASH_STATUS_VPENS)) - printf("Vpp Low Error.\n"); - } - flash_write_cmd(info, sector, 0, FLASH_CMD_RESET); - return retcode; -} -/*----------------------------------------------------------------------- - */ -static void flash_add_byte(flash_info_t *info, cfiword_t * cword, uchar c) -{ - switch(info->portwidth) { - case FLASH_CFI_8BIT: - cword->c = c; - break; - case FLASH_CFI_16BIT: - cword->w = (cword->w << 8) | c; - break; - case FLASH_CFI_32BIT: - cword->l = (cword->l << 8) | c; - } -} - - -/*----------------------------------------------------------------------- - * make a proper sized command based on the port and chip widths - */ -static void flash_make_cmd(flash_info_t * info, uchar cmd, void * cmdbuf) -{ - int i; - uchar *cp = (uchar *)cmdbuf; - for(i=0; i< info->portwidth; i++) - *cp++ = ((i+1) % info->chipwidth) ? '\0':cmd; -} - -/* - * Write a proper sized command to the correct address - */ -static void flash_write_cmd(flash_info_t * info, int sect, uchar offset, uchar cmd) -{ - - volatile cfiptr_t addr; - cfiword_t cword; - addr.cp = flash_make_addr(info, sect, offset); - flash_make_cmd(info, cmd, &cword); - switch(info->portwidth) { - case FLASH_CFI_8BIT: - *addr.cp = cword.c; - break; - case FLASH_CFI_16BIT: - *addr.wp = cword.w; - break; - case FLASH_CFI_32BIT: - *addr.lp = cword.l; - break; - } -} - -/*----------------------------------------------------------------------- - */ -static int flash_isequal(flash_info_t * info, int sect, uchar offset, uchar cmd) -{ - cfiptr_t cptr; - cfiword_t cword; - int retval; - cptr.cp = flash_make_addr(info, sect, offset); - flash_make_cmd(info, cmd, &cword); - switch(info->portwidth) { - case FLASH_CFI_8BIT: - retval = (cptr.cp[0] == cword.c); - break; - case FLASH_CFI_16BIT: - retval = (cptr.wp[0] == cword.w); - break; - case FLASH_CFI_32BIT: - retval = (cptr.lp[0] == cword.l); - break; - default: - retval = 0; - break; - } - return retval; -} -/*----------------------------------------------------------------------- - */ -static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd) -{ - cfiptr_t cptr; - cfiword_t cword; - int retval; - cptr.cp = flash_make_addr(info, sect, offset); - flash_make_cmd(info, cmd, &cword); - switch(info->portwidth) { - case FLASH_CFI_8BIT: - retval = ((cptr.cp[0] & cword.c) == cword.c); - break; - case FLASH_CFI_16BIT: - retval = ((cptr.wp[0] & cword.w) == cword.w); - break; - case FLASH_CFI_32BIT: - retval = ((cptr.lp[0] & cword.l) == cword.l); - break; - default: - retval = 0; - break; - } - return retval; -} - -/*----------------------------------------------------------------------- - * detect if flash is compatible with the Common Flash Interface (CFI) - * http://www.jedec.org/download/search/jesd68.pdf - * - */ -static int flash_detect_cfi(flash_info_t * info) -{ - - for(info->portwidth=FLASH_CFI_8BIT; info->portwidth <= FLASH_CFI_32BIT; - info->portwidth <<= 1) { - for(info->chipwidth =FLASH_CFI_BY8; - info->chipwidth <= info->portwidth; - info->chipwidth <<= 1) { - flash_write_cmd(info, 0, 0, FLASH_CMD_RESET); - flash_write_cmd(info, 0, FLASH_OFFSET_CFI, FLASH_CMD_CFI); - if(flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP,'Q') && - flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R') && - flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) - return 1; - } - } - return 0; -} -/* - * The following code cannot be run from FLASH! - * - */ -static ulong flash_get_size (ulong base, int banknum) -{ - flash_info_t * info = &flash_info[banknum]; - int i, j; - int sect_cnt; - unsigned long sector; - unsigned long tmp; - int size_ratio; - uchar num_erase_regions; - int erase_region_size; - int erase_region_count; - - info->start[0] = base; - - if(flash_detect_cfi(info)){ -#ifdef DEBUG_FLASH - printf("portwidth=%d chipwidth=%d\n", info->portwidth, info->chipwidth); /* test-only */ -#endif - size_ratio = info->portwidth / info->chipwidth; - num_erase_regions = flash_read_uchar(info, FLASH_OFFSET_NUM_ERASE_REGIONS); -#ifdef DEBUG_FLASH - printf("found %d erase regions\n", num_erase_regions); -#endif - sect_cnt = 0; - sector = base; - for(i = 0 ; i < num_erase_regions; i++) { - if(i > NUM_ERASE_REGIONS) { - printf("%d erase regions found, only %d used\n", - num_erase_regions, NUM_ERASE_REGIONS); - break; - } - tmp = flash_read_long(info, 0, FLASH_OFFSET_ERASE_REGIONS); - erase_region_size = (tmp & 0xffff)? ((tmp & 0xffff) * 256): 128; - tmp >>= 16; - erase_region_count = (tmp & 0xffff) +1; - for(j = 0; j< erase_region_count; j++) { - info->start[sect_cnt] = sector; - sector += (erase_region_size * size_ratio); - info->protect[sect_cnt] = flash_isset(info, sect_cnt, FLASH_OFFSET_PROTECT, FLASH_STATUS_PROTECT); - sect_cnt++; - } - } - - info->sector_count = sect_cnt; - /* multiply the size by the number of chips */ - info->size = (1 << flash_read_uchar(info, FLASH_OFFSET_SIZE)) * size_ratio; - info->buffer_size = (1 << flash_read_ushort(info, 0, FLASH_OFFSET_BUFFER_SIZE)); - tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_ETOUT); - info->erase_blk_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_EMAX_TOUT))); - tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WBTOUT); - info->buffer_write_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_WBMAX_TOUT))); - tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WTOUT); - info->write_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_WMAX_TOUT)))/ 1000; - info->flash_id = FLASH_MAN_CFI; - } - - flash_write_cmd(info, 0, 0, FLASH_CMD_RESET); - return(info->size); -} - - -/*----------------------------------------------------------------------- - */ -static int flash_write_cfiword (flash_info_t *info, ulong dest, cfiword_t cword) -{ - - cfiptr_t ctladdr; - cfiptr_t cptr; - int flag; - - ctladdr.cp = flash_make_addr(info, 0, 0); - cptr.cp = (uchar *)dest; - - - /* Check if Flash is (sufficiently) erased */ - switch(info->portwidth) { - case FLASH_CFI_8BIT: - flag = ((cptr.cp[0] & cword.c) == cword.c); - break; - case FLASH_CFI_16BIT: - flag = ((cptr.wp[0] & cword.w) == cword.w); - break; - case FLASH_CFI_32BIT: - flag = ((cptr.lp[0] & cword.l) == cword.l); - break; - default: - return 2; - } - if(!flag) - return 2; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - flash_write_cmd(info, 0, 0, FLASH_CMD_CLEAR_STATUS); - flash_write_cmd(info, 0, 0, FLASH_CMD_WRITE); - - switch(info->portwidth) { - case FLASH_CFI_8BIT: - cptr.cp[0] = cword.c; - break; - case FLASH_CFI_16BIT: - cptr.wp[0] = cword.w; - break; - case FLASH_CFI_32BIT: - cptr.lp[0] = cword.l; - break; - } - - /* re-enable interrupts if necessary */ - if(flag) - enable_interrupts(); - - return flash_full_status_check(info, 0, info->write_tout, "write"); -} - -#ifdef CFG_FLASH_USE_BUFFER_WRITE - -/* loop through the sectors from the highest address - * when the passed address is greater or equal to the sector address - * we have a match - */ -static int find_sector(flash_info_t *info, ulong addr) -{ - int sector; - for(sector = info->sector_count - 1; sector >= 0; sector--) { - if(addr >= info->start[sector]) - break; - } - return sector; -} - -static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp, int len) -{ - - int sector; - int cnt; - int retcode; - volatile cfiptr_t src; - volatile cfiptr_t dst; - - src.cp = cp; - dst.cp = (uchar *)dest; - sector = find_sector(info, dest); - flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS); - flash_write_cmd(info, sector, 0, FLASH_CMD_WRITE_TO_BUFFER); - if((retcode = flash_status_check(info, sector, info->buffer_write_tout, - "write to buffer")) == ERR_OK) { - switch(info->portwidth) { - case FLASH_CFI_8BIT: - cnt = len; - break; - case FLASH_CFI_16BIT: - cnt = len >> 1; - break; - case FLASH_CFI_32BIT: - cnt = len >> 2; - break; - default: - return ERR_INVAL; - break; - } - flash_write_cmd(info, sector, 0, (uchar)cnt-1); - while(cnt-- > 0) { - switch(info->portwidth) { - case FLASH_CFI_8BIT: - *dst.cp++ = *src.cp++; - break; - case FLASH_CFI_16BIT: - *dst.wp++ = *src.wp++; - break; - case FLASH_CFI_32BIT: - *dst.lp++ = *src.lp++; - break; - default: - return ERR_INVAL; - break; - } - } - flash_write_cmd(info, sector, 0, FLASH_CMD_WRITE_BUFFER_CONFIRM); - retcode = flash_full_status_check(info, sector, info->buffer_write_tout, - "buffer write"); - } - flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS); - return retcode; -} -#endif /* CFG_USE_FLASH_BUFFER_WRITE */ diff --git a/board/esd/cpci440/u-boot.lds b/board/esd/cpci440/u-boot.lds deleted file mode 100644 index b1b4ad2a978..00000000000 --- a/board/esd/cpci440/u-boot.lds +++ /dev/null @@ -1,159 +0,0 @@ -/* - * (C) Copyright 2002 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - .resetvec 0xFFFFFFFC : -/* .resetvec 0x01FFFFFC :*/ - { - *(.resetvec) - } = 0xffff - - .bootpg 0xFFFFF000 : -/* .bootpg 0x01FFF000 :*/ - { - cpu/ppc4xx/start.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - cpu/ppc4xx/start.o (.text) - board/esd/cpci440/init.o (.text) - cpu/ppc4xx/kgdb.o (.text) - cpu/ppc4xx/traps.o (.text) - cpu/ppc4xx/interrupts.o (.text) - cpu/ppc4xx/4xx_uart.o (.text) - cpu/ppc4xx/cpu_init.o (.text) - cpu/ppc4xx/speed.o (.text) - common/dlmalloc.o (.text) - lib_generic/crc32.o (.text) - lib_ppc/extable.o (.text) - lib_generic/zlib.o (.text) - -/* . = env_offset;*/ -/* common/environment.o(.text)*/ - - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - *(.eh_frame) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - _end = . ; - PROVIDE (end = .); -} diff --git a/include/configs/CPCI440.h b/include/configs/CPCI440.h deleted file mode 100644 index eb47cd7ff82..00000000000 --- a/include/configs/CPCI440.h +++ /dev/null @@ -1,287 +0,0 @@ -/* - * (C) Copyright 2002 - * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/************************************************************************ - * board/config_CPCI440.h - configuration for esd CPCI-440 board - ***********************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_CPCI440 1 /* Board is ebony */ -#define CONFIG_440GP 1 /* Specifc GP support */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ -#define CONFIG_SYS_CLK_FREQ 33330000 /* external frequency to pll */ - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#if 1 -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ -#else -#define CFG_MONITOR_BASE 0x01fc0000 /* start of monitor */ -#endif -#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ - -#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) -#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in internal SRAM) - *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ - -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#undef CFG_EXT_SERIAL_CLOCK /* (1843200 * 6) / * Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 9600 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} - -/*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. - * The DS1743 code assumes this condition (i.e. -- it assumes the base - * address for the RTC registers is: - * - * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE - * - *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */ -#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#if 1 /* test-only */ - -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_FLASH_INCREMENT 0 /* there is only one bank */ -#define CFG_FLASH_PROTECTION 1 /* use hardware protection */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#undef CFG_FLASH_BASE -#define CFG_FLASH_BASE 0xFF800000 /* test-only...*/ - -#else /* test-only */ - -#define CFG_MAX_FLASH_BANKS 3 /* number of banks */ -#define CFG_MAX_FLASH_SECT 32 /* sectors per device */ - -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#endif - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#if 0 /* test-only */ -#define CFG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ -#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */ -#undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ - -#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */ -#define CFG_ENV_ADDR \ - (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) -#else - -#if 0 /* test-only */ -#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CFG_ENV_OFFSET 0x010 /* environment starts at the beginning of the EEPROM */ -#define CFG_ENV_SIZE 0x800 /* 2048 bytes may be used for env vars*/ - /* total size of a CAT24WC16 is 2048 bytes */ -#else -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ -#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ -#endif - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F - -#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE - -#endif - -#undef CONFIG_BOOTARGS -#undef CONFIG_BOOTCOMMAND - -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#define CONFIG_BAUDRATE 9600 - -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address */ -#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_ELF -#define CONFIG_CMD_DATE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_EEPROM - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#undef CONFIG_SPD_EEPROM /* don't use SPD EEPROM for setup */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#if 0 /* test-only */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#endif - - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#if 0 -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/ - -#define CFG_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* Configuration Port location */ -#define CONFIG_PORT_ADDR 0xF0000500 - -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - * (to get SDRAM settings) - */ -#define SPD_EEPROM_ADDRESS 0x50 - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif -#endif /* __CONFIG_H */ -- cgit v1.3.1 From b56bd0fcfc1c73db722e3462c8a9bf607ba7775e Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 28 Dec 2007 17:10:42 +0100 Subject: ppc4xx: Maintenance patch for VOH405 boards - add EEPROM write protection - initialize NAND GPIOs - use correct io accessors - slow down I2C clock to 100kHz - enable ext. I2C bus - cleanup Signed-off-by: Matthias Fuchs --- board/esd/voh405/voh405.c | 135 +++++++++++++++++++++++++++++++++++++++------- include/configs/VOH405.h | 31 ++++------- 2 files changed, 127 insertions(+), 39 deletions(-) (limited to 'include') diff --git a/board/esd/voh405/voh405.c b/board/esd/voh405/voh405.c index 2857a0bef5e..87a584979b9 100644 --- a/board/esd/voh405/voh405.c +++ b/board/esd/voh405/voh405.c @@ -22,6 +22,7 @@ */ #include +#include #include #include #include @@ -112,11 +113,11 @@ int misc_init_f (void) int misc_init_r (void) { - volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4); - volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4); - volatile unsigned short *lcd_contrast = + unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4); + unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4); + unsigned short *lcd_contrast = (unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL + 4); - volatile unsigned short *lcd_backlight = + unsigned short *lcd_backlight = (unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL + 6); unsigned char *dst; ulong len = sizeof(fpgadata); @@ -180,25 +181,37 @@ int misc_init_r (void) /* * Reset FPGA via FPGA_INIT pin */ - out32(GPIO0_TCR, in32(GPIO0_TCR) | FPGA_INIT); /* setup FPGA_INIT as output */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~FPGA_INIT); /* reset low */ + out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | FPGA_INIT); /* setup FPGA_INIT as output */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~FPGA_INIT); /* reset low */ udelay(1000); /* wait 1ms */ - out32(GPIO0_OR, in32(GPIO0_OR) | FPGA_INIT); /* reset high */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | FPGA_INIT); /* reset high */ udelay(1000); /* wait 1ms */ /* * Reset external DUARTs */ - out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_DUART_RST); /* set reset to high */ udelay(10); /* wait 10us */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */ udelay(1000); /* wait 1ms */ + /* + * Set NAND-FLASH GPIO signals to default + */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE)); + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_NAND_CE); + + /* + * Setup EEPROM write protection + */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP); + out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | CFG_EEPROM_WP); + /* * Enable interrupts in exar duart mcr[3] */ - *duart0_mcr = 0x08; - *duart1_mcr = 0x08; + out_8(duart0_mcr, 0x08); + out_8(duart1_mcr, 0x08); /* * Init lcd interface and display logo @@ -240,17 +253,23 @@ int misc_init_r (void) /* * Set invert bit in small lcd controller */ - *(unsigned char *)(CFG_LCD_SMALL_REG + 2) |= 0x01; + out_8((unsigned char *)(CFG_LCD_SMALL_REG + 2), + in_8((unsigned char *)(CFG_LCD_SMALL_REG + 2)) | 0x01); /* * Set default contrast voltage on epson vga controller */ - *lcd_contrast = 0x4646; + out_be16(lcd_contrast, 0x4646); /* * Enable backlight */ - *lcd_backlight = 0xffff; + out_be16(lcd_backlight, 0xffff); + + /* + * Enable external I2C bus + */ + out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | CFG_IIC_ON); return (0); } @@ -281,11 +300,6 @@ int checkboard (void) putc ('\n'); - /* - * Disable sleep mode in LXT971 - */ - lxt971_no_sleep(); - return 0; } @@ -334,3 +348,86 @@ void ide_set_reset(int on) } } #endif /* CONFIG_IDE_RESET */ + +#if defined(CONFIG_RESET_PHY_R) +void reset_phy(void) +{ +#ifdef CONFIG_LXT971_NO_SLEEP + + /* + * Disable sleep mode in LXT971 + */ + lxt971_no_sleep(); +#endif +} +#endif + +#if defined(CFG_EEPROM_WREN) +/* Input: I2C address of EEPROM device to enable. + * -1: deliver current state + * 0: disable write + * 1: enable write + * Returns: -1: wrong device address + * 0: dis-/en- able done + * 0/1: current state if was -1. + */ +int eeprom_write_enable (unsigned dev_addr, int state) +{ + if (CFG_I2C_EEPROM_ADDR != dev_addr) { + return -1; + } else { + switch (state) { + case 1: + /* Enable write access, clear bit GPIO0. */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CFG_EEPROM_WP); + state = 0; + break; + case 0: + /* Disable write access, set bit GPIO0. */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP); + state = 0; + break; + default: + /* Read current status back. */ + state = (0 == (in_be32((void*)GPIO0_OR) & CFG_EEPROM_WP)); + break; + } + } + return state; +} + +int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int query = argc == 1; + int state = 0; + + if (query) { + /* Query write access state. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1); + if (state < 0) { + puts ("Query of write access state failed.\n"); + } else { + printf ("Write access for device 0x%0x is %sabled.\n", + CFG_I2C_EEPROM_ADDR, state ? "en" : "dis"); + state = 0; + } + } else { + if ('0' == argv[1][0]) { + /* Disable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0); + } else { + /* Enable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1); + } + if (state < 0) { + puts ("Setup of write access state failed.\n"); + } + } + + return state; +} + +U_BOOT_CMD(eepwren, 2, 0, do_eep_wren, + "eepwren - Enable / disable / query EEPROM write access\n", + NULL); +#endif /* #if defined(CFG_EEPROM_WREN) */ diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 3a413f555dc..3ca928ec931 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -52,9 +52,13 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ @@ -204,8 +208,6 @@ #define CFG_IDE_MAXBUS 2 /* max. 2 IDE busses */ #define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ -#define CONFIG_ATAPI 1 /* ATAPI for Travelstar */ - #define CFG_ATA_BASE_ADDR 0xF0100000 #define CFG_ATA_IDE0_OFFSET 0x0000 #define CFG_ATA_IDE1_OFFSET 0x0010 @@ -244,11 +246,6 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#if 0 /* test-only */ -#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ -#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */ -#endif - /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) @@ -281,19 +278,12 @@ * I2C EEPROM (CAT24WC16) for environment */ #define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ -#if 0 /* test-only */ -/* CAT24WC08/16... */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#else +#define CFG_EEPROM_WREN 1 + /* CAT24WC32/64... */ #define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ @@ -301,7 +291,6 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ /* 32 byte page write mode using*/ /* last 5 bits of the address */ -#endif #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE @@ -400,18 +389,20 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs -> GPIO */ -#define CFG_GPIO0_OSRH 0x40000550 +#define CFG_GPIO0_OSRH 0x00000550 #define CFG_GPIO0_OSRL 0x00000110 #define CFG_GPIO0_ISR1H 0x00000000 #define CFG_GPIO0_ISR1L 0x15555440 #define CFG_GPIO0_TSRH 0x00000000 #define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xF7FE0017 +#define CFG_GPIO0_TCR 0x777E0017 #define CFG_DUART_RST (0x80000000 >> 14) #define CFG_LCD_ENDIAN (0x80000000 >> 7) +#define CFG_IIC_ON (0x80000000 >> 8) #define CFG_LCD0_RST (0x80000000 >> 30) #define CFG_LCD1_RST (0x80000000 >> 31) +#define CFG_EEPROM_WP (0x80000000 >> 0) /* * Internal Definitions -- cgit v1.3.1 From f6e0f1f61896ce7729ba1bcea2ffbd138d3947f5 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 28 Dec 2007 17:10:36 +0100 Subject: ppc4xx: Add EEPROM write protection for PLU405 boards + misc. updates - add EEPROM write protection for esd PLU405 boards. - initialize NAND GPIOs - use correct io accessors - cleanup Signed-off-by: Matthias Fuchs --- board/esd/plu405/plu405.c | 95 ++++++++++++++++++++++++++++++++++++++++++++--- include/configs/PLU405.h | 6 ++- 2 files changed, 93 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c index f026a7ac3b2..57762b54ee0 100644 --- a/board/esd/plu405/plu405.c +++ b/board/esd/plu405/plu405.c @@ -109,8 +109,8 @@ int misc_init_f (void) int misc_init_r (void) { - volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4); - volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4); + unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4); + unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4); unsigned char *dst; ulong len = sizeof(fpgadata); int status; @@ -184,16 +184,28 @@ int misc_init_r (void) /* * Reset external DUARTs */ - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) | CFG_DUART_RST); + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_DUART_RST); /* set reset to high */ udelay(10); /* wait 10us */ - out_be32((void *)GPIO0_OR, in_be32((void *)GPIO0_OR) & ~CFG_DUART_RST); + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */ udelay(1000); /* wait 1ms */ + /* + * Set NAND-FLASH GPIO signals to default + */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE)); + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_NAND_CE); + + /* + * Setup EEPROM write protection + */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP); + out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) | CFG_EEPROM_WP); + /* * Enable interrupts in exar duart mcr[3] */ - *duart0_mcr = 0x08; - *duart1_mcr = 0x08; + out_8(duart0_mcr, 0x08); + out_8(duart1_mcr, 0x08); return (0); } @@ -259,3 +271,74 @@ void reset_phy(void) lxt971_no_sleep(); #endif } + + +#if defined(CFG_EEPROM_WREN) +/* Input: I2C address of EEPROM device to enable. + * -1: deliver current state + * 0: disable write + * 1: enable write + * Returns: -1: wrong device address + * 0: dis-/en- able done + * 0/1: current state if was -1. + */ +int eeprom_write_enable (unsigned dev_addr, int state) +{ + if (CFG_I2C_EEPROM_ADDR != dev_addr) { + return -1; + } else { + switch (state) { + case 1: + /* Enable write access, clear bit GPIO0. */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) & ~CFG_EEPROM_WP); + state = 0; + break; + case 0: + /* Disable write access, set bit GPIO0. */ + out_be32((void*)GPIO0_OR, in_be32((void*)GPIO0_OR) | CFG_EEPROM_WP); + state = 0; + break; + default: + /* Read current status back. */ + state = (0 == (in_be32((void*)GPIO0_OR) & CFG_EEPROM_WP)); + break; + } + } + return state; +} + +int do_eep_wren (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int query = argc == 1; + int state = 0; + + if (query) { + /* Query write access state. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, -1); + if (state < 0) { + puts ("Query of write access state failed.\n"); + } else { + printf ("Write access for device 0x%0x is %sabled.\n", + CFG_I2C_EEPROM_ADDR, state ? "en" : "dis"); + state = 0; + } + } else { + if ('0' == argv[1][0]) { + /* Disable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 0); + } else { + /* Enable write access. */ + state = eeprom_write_enable (CFG_I2C_EEPROM_ADDR, 1); + } + if (state < 0) { + puts ("Setup of write access state failed.\n"); + } + } + + return state; +} + +U_BOOT_CMD(eepwren, 2, 0, do_eep_wren, + "eepwren - Enable / disable / query EEPROM write access\n", + NULL); +#endif /* #if defined(CFG_EEPROM_WREN) */ diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 6b166540422..0bd77c07b65 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -288,6 +288,7 @@ #define CFG_I2C_SLAVE 0x7F #define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ +#define CFG_EEPROM_WREN 1 /* CAT24WC08/16... */ #define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ @@ -379,15 +380,16 @@ * GPIO0[28-29] - UART1 data signal input/output * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs */ -#define CFG_GPIO0_OSRH 0x40000550 +#define CFG_GPIO0_OSRH 0x00000550 #define CFG_GPIO0_OSRL 0x00000110 #define CFG_GPIO0_ISR1H 0x00000000 #define CFG_GPIO0_ISR1L 0x15555445 #define CFG_GPIO0_TSRH 0x00000000 #define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xF7FE0014 +#define CFG_GPIO0_TCR 0x77FE0014 #define CFG_DUART_RST (0x80000000 >> 14) +#define CFG_EEPROM_WP (0x80000000 >> 0) /* * Internal Definitions -- cgit v1.3.1 From 8ba132cab18ae438b6dd5b0214c28a8fc0d976e5 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 28 Dec 2007 17:07:24 +0100 Subject: ppc4xx: Complete PMC440 board support This patch brings the PMC440 board configuration file. Finally it enables the PMC440 board support. Signed-off-by: Matthias Fuchs --- MAINTAINERS | 1 + MAKEALL | 1 + Makefile | 3 + include/configs/PMC440.h | 522 +++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 527 insertions(+) create mode 100644 include/configs/PMC440.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index be0b8d36c52..fa0e9ea2d9e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -158,6 +158,7 @@ Matthias Fuchs PCI405 PPC405GP PLU405 PPC405EP PMC405 PPC405GP + PMC440 PPC440EPx VOH405 PPC405EP VOM405 PPC405EP WUH405 PPC405EP diff --git a/MAKEALL b/MAKEALL index a05946d42c9..0af989a8182 100755 --- a/MAKEALL +++ b/MAKEALL @@ -208,6 +208,7 @@ LIST_4xx=" \ PIP405 \ PLU405 \ PMC405 \ + PMC440 \ PPChameleonEVB \ rainier \ sbc405 \ diff --git a/Makefile b/Makefile index 87d0a77ae1d..34e9f9d70d2 100644 --- a/Makefile +++ b/Makefile @@ -1286,6 +1286,9 @@ PLU405_config: unconfig PMC405_config: unconfig @$(MKCONFIG) $(@:_config=) ppc ppc4xx pmc405 esd +PMC440_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc ppc4xx pmc440 esd + PPChameleonEVB_config \ PPChameleonEVB_BA_25_config \ PPChameleonEVB_ME_25_config \ diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h new file mode 100644 index 00000000000..3d2ed1e7d64 --- /dev/null +++ b/include/configs/PMC440.h @@ -0,0 +1,522 @@ +/* + * (C) Copyright 2007 + * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com. + * Based on the sequoia configuration file. + * + * (C) Copyright 2006-2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2006 + * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com + * Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * PMC440.h - configuration for esd PMC440 boards + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ + +#define CONFIG_SYS_CLK_FREQ 33333400 + +#define CONFIG_4xx_DCACHE /* enable dcache */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_TYPES 1 /* support board types */ +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 256 kB for malloc() */ + +#define CONFIG_PRAM 0 /* use pram variable to overwrite */ + +#define CFG_BOOT_BASE_ADDR 0xf0000000 +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CFG_OCM_BASE 0xe0010000 /* ocm */ +#define CFG_OCM_DATA_ADDR CFG_OCM_BASE +#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 +#define CFG_PCI_MEMSIZE 0x80000000 /* 2GB! */ + +/* Don't change either of these */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ + +#define CFG_USB2D0_BASE 0xe0000100 +#define CFG_USB_DEVICE 0xe0000000 +#define CFG_USB_HOST 0xe0000400 +#define CFG_FPGA_BASE0 0xef000000 /* 32 bit */ +#define CFG_FPGA_BASE1 0xef100000 /* 16 bit */ + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ +#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#define CFG_INIT_RAM_END (4 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +#undef CONFIG_UART1_CONSOLE /* console on front panel */ + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */ +#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */ +#endif + +/*----------------------------------------------------------------------- + * RTC + *----------------------------------------------------------------------*/ +#define CONFIG_RTC_RX8025 + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_OFFSET 0 /* environment starts at the beginning of the EEPROM */ +#define CFG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */ +#endif + +/* + * IPL (Initial Program Loader, integrated inside CPU) + * Will load first 4k from NAND (SPL) into cache and execute it from there. + * + * SPL (Secondary Program Loader) + * Will load special U-Boot version (NUB) from NAND and execute it. This SPL + * has to fit into 4kByte. It sets up the CPU and configures the SDRAM + * controller and the NAND controller so that the special U-Boot image can be + * loaded from NAND to SDRAM. + * + * NUB (NAND U-Boot) + * This NAND U-Boot (NUB) is a special U-Boot version which can be started + * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. + * + * On 440EPx the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from cache, I experienced problems accessing + * the NAND controller. sr - 2006-08-25 + */ +#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) + +/* + * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) + */ +#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ + +/* + * Now the NAND chip has to be defined (no autodetection used!) + */ +#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#define CFG_NAND_ECCSIZE 256 +#define CFG_NAND_ECCBYTES 3 +#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) +#define CFG_NAND_OOBSIZE 16 +#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) +#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} + +#ifdef CFG_ENV_IS_IN_NAND +/* + * For NAND booting the environment is embedded in the U-Boot image. Please take + * look at the file board/amcc/sequoia/u-boot-nand.lds for details. + */ +#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE +#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE) +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE) +#endif + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#endif + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CONFIG_I2C_CMD_TREE 1 +#define CONFIG_I2C_MULTI_BUS 1 + +#define CFG_I2C_MULTI_EEPROMS + +#define CFG_I2C_EEPROM_ADDR 0x54 +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 5 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01 + +#define CFG_EEPROM_WREN 1 +#define CFG_I2C_BOOT_EEPROM_ADDR 0x52 + +/* + * standard dtt sensor configuration - bottom bit will determine local or + * remote sensor of the TMP401 + */ +#define CONFIG_DTT_SENSORS { 0, 1 } + +/* + * The PMC440 uses a TI TMP401 temperature sensor. This part + * is basically compatible to the ADM1021 that is supported + * by U-Boot. + * + * - i2c addr 0x4c + * - conversion rate 0x02 = 0.25 conversions/second + * - ALERT ouput disabled + * - local temp sensor enabled, min set to 0 deg, max set to 70 deg + * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg + */ +#define CONFIG_DTT_ADM1021 +#define CFG_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } + +#define CONFIG_PREBOOT /* enable preboot variable */ + +#undef CONFIG_BOOTARGS + +/* Setup some board specific values for the default environment variables */ +#define CONFIG_HOSTNAME pmc440 +#define CFG_BOOTFILE "bootfile=/tftpboot/pmc440/uImage\0" +#define CFG_ROOTPATH "rootpath=/opt/eldk_410/ppc_4xx\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CFG_BOOTFILE \ + CFG_ROOTPATH \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ + "load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0" \ + "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ + "cp.b 200000 FFFA0000 60000\0" \ + "" + +#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ + +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ + +#define CONFIG_HAS_ETH0 +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 1 +#define CONFIG_RESET_PHY_R 1 + +/* USB */ +#define CONFIG_USB_OHCI_NEW +#define CONFIG_USB_STORAGE +#define CFG_OHCI_BE_CONTROLLER + +#define CFG_USB_OHCI_BOARD_INIT 1 +#define CFG_USB_OHCI_CPU_INIT 1 +#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST +#define CFG_USB_OHCI_SLOT_NAME "ppc440" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 + +/* Comment this out to enable USB 1.1 device */ +#define USB_2_0_DEVICE + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +#include + +#define CONFIG_CMD_BSP +#define CONFIG_CMD_DATE +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DTT +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_USB +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SDRAM + +/* POST support */ +/* ethernet POST sometimes freezes the CPU. + * So disable it for now until issue is solved + */ +#if 0 +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_I2C | \ + CFG_POST_CACHE | \ + CFG_POST_FPU | \ + CFG_POST_ETHER | \ + CFG_POST_SPR) +#else +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_UART | \ + CFG_POST_I2C | \ + CFG_POST_CACHE | \ + CFG_POST_FPU | \ + CFG_POST_SPR) +#endif + +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) + +/* esd expects pram at end of physical memory. + * So no logbuffer at the moment. + */ +#if 0 +#define CONFIG_LOGBUFFER +#endif +#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ + +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +#define CONFIG_SUPPORT_VFAT + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n" +#undef CONFIG_AUTOBOOT_DELAY_STR +#define CONFIG_AUTOBOOT_STOP_STR " " + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ + +/* Board-specific PCI */ +#define CFG_PCI_TARGET_INIT +#define CFG_PCI_MASTER_INIT + +/* PCI identification */ +#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */ +#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */ +#define CFG_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC +#define CFG_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FPGA stuff + *----------------------------------------------------------------------*/ +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_SPARTAN2 +#define CONFIG_FPGA_SPARTAN3 + +#define CONFIG_FPGA_COUNT 2 +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ + +/* + * On Sequoia CS0 and CS3 are switched when configuring for NAND booting + */ +#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) +#define CFG_NAND_CS 2 /* NAND chip connected to CSx */ + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x03017200 +#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) + +/* Memory Bank 2 (NAND-FLASH) initialization */ +#define CFG_EBC_PB2AP 0x018003c0 +#define CFG_EBC_PB2CR (CFG_NAND_ADDR | 0x1c000) +#else +#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +/* Memory Bank 2 (NOR-FLASH) initialization */ +#define CFG_EBC_PB2AP 0x03017200 +#define CFG_EBC_PB2CR (CFG_FLASH_BASE | 0xda000) + +/* Memory Bank 0 (NAND-FLASH) initialization */ +#define CFG_EBC_PB0AP 0x018003c0 +#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) +#endif + +/* Memory Bank 4 (FPGA / 32Bit) initialization */ +#define CFG_EBC_PB4AP 0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */ +#define CFG_EBC_PB4CR (CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */ + +/* Memory Bank 5 (FPGA / 16Bit) initialization */ +#define CFG_EBC_PB5AP 0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */ +#define CFG_EBC_PB5CR (CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ + +/*----------------------------------------------------------------------- + * NAND FLASH + *----------------------------------------------------------------------*/ +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) +#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 3dfd708cc1b2a966ad454ca9ed125dd17dbadbcc Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 2 Jan 2008 12:38:43 +0100 Subject: Minor coding style cleanup. Signed-off-by: Wolfgang Denk --- include/libfdt.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/libfdt.h b/include/libfdt.h index 6b2fb92ea35..8253ccffe16 100644 --- a/include/libfdt.h +++ b/include/libfdt.h @@ -544,7 +544,7 @@ int fdt_parent_offset(const void *fdt, int nodeoffset); * offset = fdt_node_offset_by_prop_value(fdt, -1, propname, * propval, proplen); * while (offset != -FDT_ERR_NOTFOUND) { - * // other code here + * /* other code here */ * offset = fdt_node_offset_by_prop_value(fdt, offset, propname, * propval, proplen); * } @@ -629,7 +629,7 @@ int fdt_node_check_compatible(const void *fdt, int nodeoffset, * idiom can be used: * offset = fdt_node_offset_by_compatible(fdt, -1, compatible); * while (offset != -FDT_ERR_NOTFOUND) { - * // other code here + * /* other code here */ * offset = fdt_node_offset_by_compatible(fdt, offset, compatible); * } * -- cgit v1.3.1 From 1182e9f8e3b92fc372d64943293de53daa2e26cf Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 2 Jan 2008 15:58:44 +0100 Subject: Fix compile problem introduced by "cleanup" commit 3dfd708c Signed-off-by: Wolfgang Denk --- include/libfdt.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/libfdt.h b/include/libfdt.h index 8253ccffe16..805004900da 100644 --- a/include/libfdt.h +++ b/include/libfdt.h @@ -544,7 +544,7 @@ int fdt_parent_offset(const void *fdt, int nodeoffset); * offset = fdt_node_offset_by_prop_value(fdt, -1, propname, * propval, proplen); * while (offset != -FDT_ERR_NOTFOUND) { - * /* other code here */ + * ... other code here ... * offset = fdt_node_offset_by_prop_value(fdt, offset, propname, * propval, proplen); * } @@ -629,7 +629,7 @@ int fdt_node_check_compatible(const void *fdt, int nodeoffset, * idiom can be used: * offset = fdt_node_offset_by_compatible(fdt, -1, compatible); * while (offset != -FDT_ERR_NOTFOUND) { - * /* other code here */ + * ... other code here ... * offset = fdt_node_offset_by_compatible(fdt, offset, compatible); * } * -- cgit v1.3.1 From ea9f7395ec362584e5e4f266bd0b0c4422cf6a4c Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Wed, 28 Nov 2007 14:47:18 -0600 Subject: Convert MPC8641HPCN to use libfdt. Assumes the presence of the aliases node in the DTS to locate the ethernet, pci and serial nodes for fixups. Use consistent fdtaddr and fdtfile in environment variables. Signed-off-by: Jon Loeliger --- board/freescale/mpc8641hpcn/mpc8641hpcn.c | 60 +++++++++++++++++-------------- include/configs/MPC8641HPCN.h | 21 +++++------ 2 files changed, 43 insertions(+), 38 deletions(-) (limited to 'include') diff --git a/board/freescale/mpc8641hpcn/mpc8641hpcn.c b/board/freescale/mpc8641hpcn/mpc8641hpcn.c index 931be9f375e..827878939d2 100644 --- a/board/freescale/mpc8641hpcn/mpc8641hpcn.c +++ b/board/freescale/mpc8641hpcn/mpc8641hpcn.c @@ -27,11 +27,8 @@ #include #include #include - -#if defined(CONFIG_OF_FLAT_TREE) -#include -extern void ft_cpu_setup(void *blob, bd_t *bd); -#endif +#include +#include #include "../common/pixis.h" @@ -324,36 +321,47 @@ void pci_init_board(void) } -#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +#if defined(CONFIG_OF_BOARD_SETUP) void ft_board_setup(void *blob, bd_t *bd) { - u32 *p; - int len; + int node, tmp[2]; + const char *path; - ft_cpu_setup(blob, bd); + fdt_fixup_ethernet(blob, bd); - p = ft_get_prop(blob, "/memory/reg", &len); - if (p != NULL) { - *p++ = cpu_to_be32(bd->bi_memstart); - *p = cpu_to_be32(bd->bi_memsize); - } + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "timebase-frequency", bd->bi_busfreq / 4, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "soc", 4, + "bus-frequency", bd->bi_busfreq, 1); + + do_fixup_by_compat_u32(blob, "ns16550", + "clock-frequency", bd->bi_busfreq, 1); + + fdt_fixup_memory(blob, bd->bi_memstart, bd->bi_memsize); + + node = fdt_path_offset(blob, "/aliases"); + tmp[0] = 0; + if (node >= 0) { #ifdef CONFIG_PCI1 - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pcie@8000/bus-range", &len); - if (p != NULL) { - p[0] = 0; - p[1] = pci1_hose.last_busno - pci1_hose.first_busno; - debug("PCI@8000 first_busno=%d last_busno=%d\n",p[0],p[1]); - } + path = fdt_getprop(blob, node, "pci0", NULL); + if (path) { + tmp[1] = pci1_hose.last_busno - pci1_hose.first_busno; + do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); + } #endif #ifdef CONFIG_PCI2 - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pcie@9000/bus-range", &len); - if (p != NULL) { - p[0] = 0; - p[1] = pci2_hose.last_busno - pci2_hose.first_busno; - debug("PCI@9000 first_busno=%d last_busno=%d\n",p[0],p[1]); - } + path = fdt_getprop(blob, node, "pci1", NULL); + if (path) { + tmp[1] = pci2_hose.last_busno - pci2_hose.first_busno; + do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); + } #endif + } } #endif diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 6f872402633..0fc65213cce 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -267,13 +267,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * Pass open firmware flat tree to kernel */ -#define CONFIG_OF_FLAT_TREE 1 -#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define OF_CPU "PowerPC,8641@0" -#define OF_SOC "soc8641@f8000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500" #define CFG_64BIT_VSPRINTF 1 #define CFG_64BIT_STRTOUL 1 @@ -645,8 +642,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=your.ramdisk.u-boot\0" \ - "dtbaddr=c00000\0" \ - "dtbfile=mpc8641_hpcn.dtb\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=mpc8641_hpcn.dtb\0" \ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ "maxcpus=2" @@ -658,16 +655,16 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr $ramdiskaddr $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND -- cgit v1.3.1 From 61d3421bdea090bd0399b14c3e10a3bebcc8d5ff Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Tue, 4 Dec 2007 10:53:34 -0600 Subject: Don't slam #undef DEBUG in the 8641HPCN config file. Doing so prevents it from being individually set and useful in other files. Signed-off-by: Jon Loeliger --- include/configs/MPC8641HPCN.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 0fc65213cce..575bbae431f 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -38,7 +38,6 @@ #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ #define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ -#undef DEBUG #ifdef RUN_DIAG #define CFG_DIAG_ADDR 0xff800000 -- cgit v1.3.1 From f85b60710571b37293d2233933b76e2aa3db5635 Mon Sep 17 00:00:00 2001 From: Rafal Jaworowski Date: Thu, 27 Dec 2007 18:19:02 +0100 Subject: Introduce new eth_receive routine The purpose of this routine is receiving a single network frame, outside of U-Boot's NetLoop(). Exporting it to standalone programs that run on top of U-Boot will let them utilise networking facilities. For sending a raw frame the already existing eth_send() can be used. The direct consumer of this routine is the newly introduced API layer for external applications (enabled with CONFIG_API). Signed-off-by: Rafal Jaworowski Signed-off-by: Piotr Kruszynski Signed-off-by: Ben Warren --- include/net.h | 3 +++ net/eth.c | 58 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ net/net.c | 10 ++++++++++ 3 files changed, 71 insertions(+) (limited to 'include') diff --git a/include/net.h b/include/net.h index 603452ab328..f6decdca883 100644 --- a/include/net.h +++ b/include/net.h @@ -122,6 +122,9 @@ extern void eth_set_enetaddr(int num, char* a); /* Set new MAC address */ extern int eth_init(bd_t *bis); /* Initialize the device */ extern int eth_send(volatile void *packet, int length); /* Send a packet */ +#ifdef CONFIG_API +extern int eth_receive(volatile void *packet, int length); /* Receive a packet */ +#endif extern int eth_rx(void); /* Check for received packets */ extern void eth_halt(void); /* stop SCC */ extern char *eth_get_name(void); /* get name of current device */ diff --git a/net/eth.c b/net/eth.c index 1b56a356c4f..4657f7970f6 100644 --- a/net/eth.c +++ b/net/eth.c @@ -62,6 +62,17 @@ extern int bfin_EMAC_initialize(bd_t *); extern int atstk1000_eth_initialize(bd_t *); extern int mcffec_initialize(bd_t*); +#ifdef CONFIG_API +extern void (*push_packet)(volatile void *, int); + +static struct { + uchar data[PKTSIZE]; + int length; +} eth_rcv_bufs[PKTBUFSRX]; + +static unsigned int eth_rcv_current = 0, eth_rcv_last = 0; +#endif + static struct eth_device *eth_devices, *eth_current; struct eth_device *eth_get_dev(void) @@ -457,6 +468,53 @@ int eth_rx(void) return eth_current->recv(eth_current); } +#ifdef CONFIG_API +static void eth_save_packet(volatile void *packet, int length) +{ + volatile char *p = packet; + int i; + + if ((eth_rcv_last+1) % PKTBUFSRX == eth_rcv_current) + return; + + if (PKTSIZE < length) + return; + + for (i = 0; i < length; i++) + eth_rcv_bufs[eth_rcv_last].data[i] = p[i]; + + eth_rcv_bufs[eth_rcv_last].length = length; + eth_rcv_last = (eth_rcv_last + 1) % PKTBUFSRX; +} + +int eth_receive(volatile void *packet, int length) +{ + volatile char *p = packet; + void *pp = push_packet; + int i; + + if (eth_rcv_current == eth_rcv_last) { + push_packet = eth_save_packet; + eth_rx(); + push_packet = pp; + + if (eth_rcv_current == eth_rcv_last) + return -1; + } + + if (length < eth_rcv_bufs[eth_rcv_current].length) + return -1; + + length = eth_rcv_bufs[eth_rcv_current].length; + + for (i = 0; i < length; i++) + p[i] = eth_rcv_bufs[eth_rcv_current].data[i]; + + eth_rcv_current = (eth_rcv_current + 1) % PKTBUFSRX; + return length; +} +#endif /* CONFIG_API */ + void eth_try_another(int first_restart) { static struct eth_device *first_failed = NULL; diff --git a/net/net.c b/net/net.c index c719bc4c0f3..cac3e09d96d 100644 --- a/net/net.c +++ b/net/net.c @@ -137,6 +137,9 @@ uchar NetBcastAddr[6] = /* Ethernet bcast address */ { 0xff, 0xff, 0xff, 0xff, 0xff, 0xff }; uchar NetEtherNullAddr[6] = { 0, 0, 0, 0, 0, 0 }; +#ifdef CONFIG_API +void (*push_packet)(volatile void *, int len) = 0; +#endif #if defined(CONFIG_CMD_CDP) uchar NetCDPAddr[6] = /* Ethernet bcast address */ { 0x01, 0x00, 0x0c, 0xcc, 0xcc, 0xcc }; @@ -1161,6 +1164,13 @@ NetReceive(volatile uchar * inpkt, int len) if (len < ETHER_HDR_SIZE) return; +#ifdef CONFIG_API + if (push_packet) { + (*push_packet)(inpkt, len); + return; + } +#endif + #if defined(CONFIG_CMD_CDP) /* keep track if packet is CDP */ iscdp = memcmp(et->et_dest, NetCDPAddr, 6) == 0; -- cgit v1.3.1 From 5ab884b254ca2e707ab50545cd705f30108cf491 Mon Sep 17 00:00:00 2001 From: "Lawrence R. Johnson" Date: Thu, 3 Jan 2008 18:54:00 -0500 Subject: ppc4xx: Add functionality to GPIO support This patch makes two additions to GPIO support: First, it adds function gpio_read_in_bit() to read the a bit from the GPIO Input Register (GPIOx_IR) in the same way that function gpio_read_out_bit() reads a bit from the GPIO Output Register (GPIOx_OR). Second, it modifies function gpio_set_chip_configuration() to provide an additional option for configuring the GPIO from the "CFG_4xx_GPIO_TABLE". According to the 440EPx User's Manual, when an alternate output is used, the three-state control is configured in one of two ways, depending on the particular output. The first option is to select the corresponding alternate three-state control in the GPIOx_TRSH/L registers. The second option is to select the GPIO Three-State Control Register (GPIOx_TCR) in the GPIOx_TRSH/L registers, and set the corresponding bit in the GPIOx_TCR register to enable the output. For example, the Manual specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use the alternate three-state control (first option), and specifies configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output enabled in the GPIOx_TCR register (second option). Currently, gpio_set_chip_configuration() configures all alternate signal outputs to use the first option. This patch allow the second option to be selected by setting the "out_val" element in the table entry to "GPIO_OUT_1". The first option is used when the "out_val" element is set to "GPIO_OUT_0". Because "out_val" is not currently used when an alternate signal is selected, and because all current GPIO tables set "out_val" to "GPIO_OUT_0" for all alternate signals, this patch should not change any existing configurations. Signed-off-by: Larry Johnson --- cpu/ppc4xx/gpio.c | 63 ++++++++++++++++++++++++++++++++------------------ include/asm-ppc/gpio.h | 1 + 2 files changed, 41 insertions(+), 23 deletions(-) (limited to 'include') diff --git a/cpu/ppc4xx/gpio.c b/cpu/ppc4xx/gpio.c index 7b09a2f7d37..37d3fa8ef74 100644 --- a/cpu/ppc4xx/gpio.c +++ b/cpu/ppc4xx/gpio.c @@ -27,7 +27,7 @@ #include #if defined(CFG_4xx_GPIO_TABLE) -gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_4xx_GPIO_TABLE; +gpio_param_s const gpio_tab[GPIO_GROUP_MAX][GPIO_MAX] = CFG_4xx_GPIO_TABLE; #endif #if defined(GPIO0_OSRL) @@ -120,6 +120,18 @@ int gpio_read_out_bit(int pin) return (in_be32((void *)GPIO0_OR + offs) & GPIO_VAL(pin) ? 1 : 0); } +int gpio_read_in_bit(int pin) +{ + u32 offs = 0; + + if (pin >= GPIO_MAX) { + offs = 0x100; + pin -= GPIO_MAX; + } + + return (in_be32((void *)GPIO0_IR + offs) & GPIO_VAL(pin) ? 1 : 0); +} + #if defined(CFG_4xx_GPIO_TABLE) void gpio_set_chip_configuration(void) { @@ -171,6 +183,8 @@ void gpio_set_chip_configuration(void) if ((gpio_tab[gpio_core][i].in_out == GPIO_OUT) || (gpio_tab[gpio_core][i].in_out == GPIO_BI)) { + u32 gpio_alt_sel = 0; + switch (gpio_tab[gpio_core][i].alt_nb) { case GPIO_SEL: /* @@ -199,37 +213,40 @@ void gpio_set_chip_configuration(void) break; case GPIO_ALT1: - reg = in_be32((void *)GPIO_OS(core_add+offs)) - & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT1_SEL >> (j*2)); - out_be32((void *)GPIO_OS(core_add+offs), reg); - reg = in_be32((void *)GPIO_TS(core_add+offs)) - & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT1_SEL >> (j*2)); - out_be32((void *)GPIO_TS(core_add+offs), reg); + gpio_alt_sel = GPIO_ALT1_SEL; break; case GPIO_ALT2: - reg = in_be32((void *)GPIO_OS(core_add+offs)) - & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT2_SEL >> (j*2)); - out_be32((void *)GPIO_OS(core_add+offs), reg); - reg = in_be32((void *)GPIO_TS(core_add+offs)) - & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT2_SEL >> (j*2)); - out_be32((void *)GPIO_TS(core_add+offs), reg); + gpio_alt_sel = GPIO_ALT2_SEL; break; case GPIO_ALT3: + gpio_alt_sel = GPIO_ALT3_SEL; + break; + } + + if (0 != gpio_alt_sel) { reg = in_be32((void *)GPIO_OS(core_add+offs)) & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT3_SEL >> (j*2)); + reg = reg | (gpio_alt_sel >> (j*2)); out_be32((void *)GPIO_OS(core_add+offs), reg); - reg = in_be32((void *)GPIO_TS(core_add+offs)) - & ~(GPIO_MASK >> (j*2)); - reg = reg | (GPIO_ALT3_SEL >> (j*2)); - out_be32((void *)GPIO_TS(core_add+offs), reg); - break; + + if (gpio_tab[gpio_core][i].out_val == GPIO_OUT_1) { + reg = in_be32((void *)GPIO_TCR(core_add)) + | (0x80000000 >> (i)); + out_be32((void *)GPIO_TCR(core_add), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) + & ~(GPIO_MASK >> (j*2)); + out_be32((void *)GPIO_TS(core_add+offs), reg); + } else { + reg = in_be32((void *)GPIO_TCR(core_add)) + & ~(0x80000000 >> (i)); + out_be32((void *)GPIO_TCR(core_add), reg); + reg = in_be32((void *)GPIO_TS(core_add+offs)) + & ~(GPIO_MASK >> (j*2)); + reg = reg | (gpio_alt_sel >> (j*2)); + out_be32((void *)GPIO_TS(core_add+offs), reg); + } } } } diff --git a/include/asm-ppc/gpio.h b/include/asm-ppc/gpio.h index d0c3eba8846..c3a4a88d581 100644 --- a/include/asm-ppc/gpio.h +++ b/include/asm-ppc/gpio.h @@ -88,6 +88,7 @@ typedef struct { void gpio_config(int pin, int in_out, int gpio_alt, int out_val); void gpio_write_bit(int pin, int val); int gpio_read_out_bit(int pin); +int gpio_read_in_bit(int pin); void gpio_set_chip_configuration(void); #endif /* __ASM_PPC_GPIO_H */ -- cgit v1.3.1 From b05e8bf58be9d8956fdfde3d8c8e87c140414663 Mon Sep 17 00:00:00 2001 From: "Lawrence R. Johnson" Date: Fri, 4 Jan 2008 02:11:56 -0500 Subject: ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board Note: this patch changes the configuration of some GPIO registers: Register Old Value New Value --------------- ---------- ---------- DCR GPIO0_TCR 0x0000000F 0x0000F0CF DCR GPIO0_TSRH 0x55005000 0x00000000 DCR GPIO1_TCR 0xC2000000 0xE2000000 DCR GPIO1_TSRL 0x0C000000 0x00200000 DCR GPIO1_ISR2L 0x00050000 0x00110000 Signed-off-by: Larry Johnson --- board/amcc/sequoia/sequoia.c | 31 +----------------- include/configs/sequoia.h | 77 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 78 insertions(+), 30 deletions(-) (limited to 'include') diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index 37b4f31b908..2268bc06b19 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -26,6 +26,7 @@ #include #include #include +#include #include #include @@ -44,36 +45,6 @@ int board_early_init_f(void) mtdcr(ebccfga, xbcfg); mtdcr(ebccfgd, 0xb8400000); - /*-------------------------------------------------------------------- - * Setup the GPIO pins - *-------------------------------------------------------------------*/ - /* test-only: take GPIO init from pcs440ep ???? in config file */ - out_be32((u32 *) GPIO0_OR, 0x00000000); - out_be32((u32 *) GPIO0_TCR, 0x0000000f); - out_be32((u32 *) GPIO0_OSRL, 0x50015400); - out_be32((u32 *) GPIO0_OSRH, 0x550050aa); - out_be32((u32 *) GPIO0_TSRL, 0x50015400); - out_be32((u32 *) GPIO0_TSRH, 0x55005000); - out_be32((u32 *) GPIO0_ISR1L, 0x50000000); - out_be32((u32 *) GPIO0_ISR1H, 0x00000000); - out_be32((u32 *) GPIO0_ISR2L, 0x00000000); - out_be32((u32 *) GPIO0_ISR2H, 0x00000100); - out_be32((u32 *) GPIO0_ISR3L, 0x00000000); - out_be32((u32 *) GPIO0_ISR3H, 0x00000000); - - out_be32((u32 *) GPIO1_OR, 0x00000000); - out_be32((u32 *) GPIO1_TCR, 0xc2000000); - out_be32((u32 *) GPIO1_OSRL, 0x5c280000); - out_be32((u32 *) GPIO1_OSRH, 0x00000000); - out_be32((u32 *) GPIO1_TSRL, 0x0c000000); - out_be32((u32 *) GPIO1_TSRH, 0x00000000); - out_be32((u32 *) GPIO1_ISR1L, 0x00005550); - out_be32((u32 *) GPIO1_ISR1H, 0x00000000); - out_be32((u32 *) GPIO1_ISR2L, 0x00050000); - out_be32((u32 *) GPIO1_ISR2H, 0x00000000); - out_be32((u32 *) GPIO1_ISR3L, 0x01400000); - out_be32((u32 *) GPIO1_ISR3H, 0x00000000); - /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 1f72b54884b..8929134b5ff 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -476,6 +476,83 @@ #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +/*----------------------------------------------------------------------- + * PPC440 GPIO Configuration + */ +/* test-only: take GPIO init from pcs440ep ???? in config file */ +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO14 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO28 USB2D_TXVALID */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ +}, \ +{ \ +/* GPIO Core 1 */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ +{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ +} \ +} + /* * Internal Definitions * -- cgit v1.3.1 From 0ddd969aec532bd7eae30fc09590488a3aaa629a Mon Sep 17 00:00:00 2001 From: "Lawrence R. Johnson" Date: Thu, 3 Jan 2008 15:02:02 -0500 Subject: ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board Signed-off-by: Larry Johnson --- board/korat/korat.c | 117 +++--------------------------------- include/configs/korat.h | 153 +++++++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 161 insertions(+), 109 deletions(-) (limited to 'include') diff --git a/board/korat/korat.c b/board/korat/korat.c index 7cb9ee11f36..199c1ff9da5 100644 --- a/board/korat/korat.c +++ b/board/korat/korat.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Larry Johnson, lrj@acm.org * * (C) Copyright 2006 @@ -26,6 +26,7 @@ */ #include +#include #include #include #include @@ -40,109 +41,12 @@ ulong flash_get_size(ulong base, int banknum); int board_early_init_f(void) { u32 sdr0_pfc1, sdr0_pfc2; - u32 gpio0_ir; u32 reg; int eth; mtdcr(ebccfga, xbcfg); mtdcr(ebccfgd, 0xb8400000); - /*-------------------------------------------------------------------- - * Setup the GPIO pins - * - * Korat GPIO usage: - * - * Init. - * Pin Source I/O value Function - * ------ ------ --- ----- --------------------------------- - * GPIO00 Alt1 I/O x PerAddr07 - * GPIO01 Alt1 I/O x PerAddr06 - * GPIO02 Alt1 I/O x PerAddr05 - * GPIO03 GPIO x x GPIO03 to expansion bus connector - * GPIO04 GPIO x x GPIO04 to expansion bus connector - * GPIO05 GPIO x x GPIO05 to expansion bus connector - * GPIO06 Alt1 O x PerCS1 (2nd NOR flash) - * GPIO07 Alt1 O x PerCS2 (CPLD) - * GPIO08 Alt1 O x PerCS3 to expansion bus connector - * GPIO09 Alt1 O x PerCS4 to expansion bus connector - * GPIO10 Alt1 O x PerCS5 to expansion bus connector - * GPIO11 Alt1 I x PerErr - * GPIO12 GPIO O 0 ATMega !Reset - * GPIO13 GPIO O 1 SPI Atmega !SS - * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8) - * GPIO15 GPIO O 0 CPU Run LED !On - * GPIO16 Alt1 O x GMC1TxD0 - * GPIO17 Alt1 O x GMC1TxD1 - * GPIO18 Alt1 O x GMC1TxD2 - * GPIO19 Alt1 O x GMC1TxD3 - * GPIO20 Alt1 O x RejectPkt0 - * GPIO21 Alt1 O x RejectPkt1 - * GPIO22 GPIO I x PGOOD_DDR - * GPIO23 Alt1 O x SCPD0 - * GPIO24 Alt1 O x GMC0TxD2 - * GPIO25 Alt1 O x GMC0TxD3 - * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4) - * GPIO27 GPIO O 0 PHY #0 1000BASE-X - * GPIO28 GPIO O 0 PHY #1 1000BASE-X - * GPIO29 GPIO I x Test jumper !Present - * GPIO30 GPIO I x SFP module #0 !Present - * GPIO31 GPIO I x SFP module #1 !Present - * - * GPIO32 GPIO O 1 SFP module #0 Tx !Enable - * GPIO33 GPIO O 1 SFP module #1 Tx !Enable - * GPIO34 Alt2 I x !UART1_CTS - * GPIO35 Alt2 O x !UART1_RTS - * GPIO36 Alt1 I x !UART0_CTS - * GPIO37 Alt1 O x !UART0_RTS - * GPIO38 Alt2 O x UART1_Tx - * GPIO39 Alt2 I x UART1_Rx - * GPIO40 Alt1 I x IRQ0 (Ethernet 0) - * GPIO41 Alt1 I x IRQ1 (Ethernet 1) - * GPIO42 Alt1 I x IRQ2 (PCI interrupt) - * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD) - * GPIO44 xxxx x x (grounded through pulldown) - * GPIO45 GPIO O 0 PHY #0 Enable - * GPIO46 GPIO O 0 PHY #1 Enable - * GPIO47 GPIO I x Reset switch !Pressed - * GPIO48 GPIO I x Shutdown switch !Pressed - * GPIO49 xxxx x x (reserved for trace port) - * . . . . . - * . . . . . - * . . . . . - * GPIO63 xxxx x x (reserved for trace port) - *-------------------------------------------------------------------*/ - - out_be32((u32 *) GPIO0_OR, 0x00060000); - out_be32((u32 *) GPIO1_OR, 0xC0000000); - - out_be32((u32 *) GPIO0_OSRL, 0x54055400); - out_be32((u32 *) GPIO0_OSRH, 0x55015000); - out_be32((u32 *) GPIO1_OSRL, 0x02180000); - out_be32((u32 *) GPIO1_OSRH, 0x00000000); - - out_be32((u32 *) GPIO0_TSRL, 0x54055500); - out_be32((u32 *) GPIO0_TSRH, 0x00015000); - out_be32((u32 *) GPIO1_TSRL, 0x00000000); - out_be32((u32 *) GPIO1_TSRH, 0x00000000); - - out_be32((u32 *) GPIO0_TCR, 0x000FF0D8); - out_be32((u32 *) GPIO1_TCR, 0xD6060000); - - out_be32((u32 *) GPIO0_ISR1L, 0x54000100); - out_be32((u32 *) GPIO0_ISR1H, 0x00500000); - out_be32((u32 *) GPIO1_ISR1L, 0x00405500); - out_be32((u32 *) GPIO1_ISR1H, 0x00000000); - - out_be32((u32 *) GPIO0_ISR2L, 0x00000000); - out_be32((u32 *) GPIO0_ISR2H, 0x00000000); - out_be32((u32 *) GPIO1_ISR2L, 0x04010000); - out_be32((u32 *) GPIO1_ISR2H, 0x00000000); - - out_be32((u32 *) GPIO0_ISR3L, 0x00000000); - out_be32((u32 *) GPIO0_ISR3H, 0x00000000); - out_be32((u32 *) GPIO1_ISR3L, 0x00000000); - out_be32((u32 *) GPIO1_ISR3H, 0x00000000); - /*-------------------------------------------------------------------- * Setup the interrupt controller polarities, triggers, etc. *-------------------------------------------------------------------*/ @@ -176,9 +80,8 @@ int board_early_init_f(void) /* Configure the two Ethernet PHYs. For each PHY, configure for fiber * if the SFP module is present, and for copper if it is not present. */ - gpio0_ir = in_be32((u32 *) GPIO0_IR); for (eth = 0; eth < 2; ++eth) { - if (gpio0_ir & (0x00000001 << (1 - eth))) { + if (gpio_read_in_bit(CFG_GPIO_SFP0_PRESENT_ + eth)) { /* SFP module not present: configure PHY for copper. */ /* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */ out_8((u8 *) CFG_CPLD_BASE + 0x06, @@ -187,14 +90,13 @@ int board_early_init_f(void) } else { /* SFP module present: configure PHY for fiber and enable output */ - out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) | - (0x00000001 << (4 - eth))); - out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) & - ~(0x00000001 << (31 - eth))); + gpio_write_bit(CFG_GPIO_PHY0_FIBER_SEL + eth, 1); + gpio_write_bit(CFG_GPIO_SFP0_TX_EN_ + eth, 0); } } /* enable Ethernet: set GPIO45 and GPIO46 to 1 */ - out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000); + gpio_write_bit(CFG_GPIO_PHY0_EN, 1); + gpio_write_bit(CFG_GPIO_PHY1_EN, 1); /* select Ethernet pins */ mfsdr(SDR0_PFC1, sdr0_pfc1); @@ -525,20 +427,19 @@ int checkboard(void) { char const *const s = getenv("serial#"); u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0); - u32 const gpio0_or = in_be32((u32 *) GPIO0_OR); printf("Board: Korat, Rev. %X", rev); if (s != NULL) printf(", serial# %s", s); printf(", Ethernet PHY 0: "); - if (gpio0_or & 0x00000010) + if (gpio_read_out_bit(CFG_GPIO_PHY0_FIBER_SEL)) printf("fiber"); else printf("copper"); printf(", PHY 1: "); - if (gpio0_or & 0x00000008) + if (gpio_read_out_bit(CFG_GPIO_PHY1_FIBER_SEL)) printf("fiber"); else printf("copper"); diff --git a/include/configs/korat.h b/include/configs/korat.h index 1ea7d4894aa..7d0640bbcf8 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Larry Johnson, lrj@acm.org * * (C) Copyright 2006-2007 @@ -361,6 +361,157 @@ #define CFG_EBC_PB2AP 0x04017300 #define CFG_EBC_PB2CR (CFG_CPLD_BASE | 0x00038000) +/*----------------------------------------------------------------------- + * GPIO Setup + * + * Korat GPIO usage: + * + * Init. + * Pin Source I/O value Function + * ------ ------ --- ----- --------------------------------- + * GPIO00 Alt1 I/O x PerAddr07 + * GPIO01 Alt1 I/O x PerAddr06 + * GPIO02 Alt1 I/O x PerAddr05 + * GPIO03 GPIO x x GPIO03 to expansion bus connector + * GPIO04 GPIO x x GPIO04 to expansion bus connector + * GPIO05 GPIO x x GPIO05 to expansion bus connector + * GPIO06 Alt1 O x PerCS1 (2nd NOR flash) + * GPIO07 Alt1 O x PerCS2 (CPLD) + * GPIO08 Alt1 O x PerCS3 to expansion bus connector + * GPIO09 Alt1 O x PerCS4 to expansion bus connector + * GPIO10 Alt1 O x PerCS5 to expansion bus connector + * GPIO11 Alt1 I x PerErr + * GPIO12 GPIO O 0 ATMega !Reset + * GPIO13 GPIO O 1 SPI Atmega !SS + * GPIO14 GPIO O 1 Write protect EEPROM #1 (0xA8) + * GPIO15 GPIO O 0 CPU Run LED !On + * GPIO16 Alt1 O x GMC1TxD0 + * GPIO17 Alt1 O x GMC1TxD1 + * GPIO18 Alt1 O x GMC1TxD2 + * GPIO19 Alt1 O x GMC1TxD3 + * GPIO20 Alt1 I x RejectPkt0 + * GPIO21 Alt1 I x RejectPkt1 + * GPIO22 GPIO I x PGOOD_DDR + * GPIO23 Alt1 O x SCPD0 + * GPIO24 Alt1 O x GMC0TxD2 + * GPIO25 Alt1 O x GMC0TxD3 + * GPIO26 GPIO? I/O x IIC0SDA (selected in SDR0_PFC4) + * GPIO27 GPIO O 0 PHY #0 1000BASE-X select + * GPIO28 GPIO O 0 PHY #1 1000BASE-X select + * GPIO29 GPIO I x Test jumper !Present + * GPIO30 GPIO I x SFP module #0 !Present + * GPIO31 GPIO I x SFP module #1 !Present + * + * GPIO32 GPIO O 1 SFP module #0 Tx !Enable + * GPIO33 GPIO O 1 SFP module #1 Tx !Enable + * GPIO34 Alt2 I x !UART1_CTS + * GPIO35 Alt2 O x !UART1_RTS + * GPIO36 Alt1 I x !UART0_CTS + * GPIO37 Alt1 O x !UART0_RTS + * GPIO38 Alt2 O x UART1_Tx + * GPIO39 Alt2 I x UART1_Rx + * GPIO40 Alt1 I x IRQ0 (Ethernet 0) + * GPIO41 Alt1 I x IRQ1 (Ethernet 1) + * GPIO42 Alt1 I x IRQ2 (PCI interrupt) + * GPIO43 Alt1 I x IRQ3 (System Alert from CPLD) + * GPIO44 xxxx x x (grounded through pulldown) + * GPIO45 GPIO O 0 PHY #0 Enable + * GPIO46 GPIO O 0 PHY #1 Enable + * GPIO47 GPIO I x Reset switch !Pressed + * GPIO48 GPIO I x Shutdown switch !Pressed + * GPIO49 xxxx x x (reserved for trace port) + * . . . . . + * . . . . . + * . . . . . + * GPIO63 xxxx x x (reserved for trace port) +*----------------------------------------------------------------------*/ + +#define CFG_GPIO_ATMEGA_SS_ 13 +#define CFG_GPIO_PHY0_FIBER_SEL 27 +#define CFG_GPIO_PHY1_FIBER_SEL 28 +#define CFG_GPIO_SFP0_PRESENT_ 30 +#define CFG_GPIO_SFP1_PRESENT_ 31 +#define CFG_GPIO_SFP0_TX_EN_ 32 +#define CFG_GPIO_SFP1_TX_EN_ 33 +#define CFG_GPIO_PHY0_EN 45 +#define CFG_GPIO_PHY1_EN 46 + +/*----------------------------------------------------------------------- + * PPC440 GPIO Configuration + */ +#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ +{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ +{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ +{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ +{GPIO0_BASE, GPIO_DIS, GPIO_SEL , GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO13 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO15 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO16 GMCTxD(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO17 GMCTxD(5) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO18 GMCTxD(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO19 GMCTxD(7) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO24 GMCTxD(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO25 GMCTxD(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ +}, \ +{ \ +/* GPIO Core 1 */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ +} \ +} + /* * Internal Definitions * -- cgit v1.3.1 From 845c6c95dbfe6c915ce68a0a115852fa17932fb4 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Sat, 5 Jan 2008 09:12:41 +0100 Subject: ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setup On Katmai the complete auto-calibration somehow doesn't seem to produce the best results, meaning optimal values for RQFD/RFFD. This was discovered by GDA using a high bandwidth scope, analyzing the DDR2 signals. GDA provided a fixed value for RQFD, so now on Katmai "only" RFFD is auto-calibrated. This patch also adds RDCC calibration as mentioned on page 7 of the AMCC PowerPC440SP/SPe DDR2 application note: "DDR1/DDR2 Initialization Sequence and Dynamic Tuning" Signed-off-by: Stefan Roese --- board/amcc/katmai/katmai.c | 14 ++++++++++++- cpu/ppc4xx/44x_spd_ddr2.c | 52 +++++++++++++++++++++++++++++++++------------- include/configs/katmai.h | 1 + include/ppc440.h | 12 +++++++++-- 4 files changed, 61 insertions(+), 18 deletions(-) (limited to 'include') diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c index 25c9a22feab..e41caaf344c 100644 --- a/board/amcc/katmai/katmai.c +++ b/board/amcc/katmai/katmai.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this @@ -246,6 +246,18 @@ int checkboard (void) return 0; } +/* + * Override the default functions in cpu/ppc4xx/44x_spd_ddr2.c with + * board specific values. + */ +u32 ddr_wrdtr(u32 default_val) { + return (SDRAM_WRDTR_LLWP_1_CYC | SDRAM_WRDTR_WTR_180_DEG_ADV | 0x823); +} + +u32 ddr_clktr(u32 default_val) { + return (SDRAM_CLKTR_CLKP_90_DEG_ADV); +} + #if defined(CFG_DRAM_TEST) int testdram (void) { diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index e19929437e2..2475ed95ecf 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -3,7 +3,7 @@ * This SPD SDRAM detection code supports AMCC PPC44x cpu's with a * DDR2 controller (non Denali Core). Those are 440SP/SPe. * - * (C) Copyright 2007 + * (C) Copyright 2007-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * * COPYRIGHT AMCC CORPORATION 2004 @@ -2409,17 +2409,10 @@ static void program_DQS_calibration(unsigned long *dimm_populated, * Read sample cycle auto-update enable *-----------------------------------------------------------------*/ - /* - * Modified for the Katmai platform: with some DIMMs, the DDR2 - * controller automatically selects the T2 read cycle, but this - * proves unreliable. Go ahead and force the DDR2 controller - * to use the T4 sample and disable the automatic update of the - * RDSS field. - */ mfsdram(SDRAM_RDCC, val); mtsdram(SDRAM_RDCC, (val & ~(SDRAM_RDCC_RDSS_MASK | SDRAM_RDCC_RSAE_MASK)) - | (SDRAM_RDCC_RDSS_T4 | SDRAM_RDCC_RSAE_DISABLE)); + | SDRAM_RDCC_RSAE_ENABLE); /*------------------------------------------------------------------ * Program RQDC register @@ -2512,10 +2505,7 @@ static void DQS_calibration_process(void) { unsigned long rfdc_reg; unsigned long rffd; - unsigned long rqdc_reg; - unsigned long rqfd; unsigned long val; - long rqfd_average; long rffd_average; long max_start; long min_end; @@ -2533,10 +2523,14 @@ static void DQS_calibration_process(void) long max_end; unsigned char fail_found; unsigned char pass_found; +#if !defined(CONFIG_DDR_RQDC_FIXED) + u32 rqdc_reg; + u32 rqfd; u32 rqfd_start; + u32 rqfd_average; + int loopi = 0; char str[] = "Auto calibration -"; char slash[] = "\\|/-\\|/-"; - int loopi = 0; /*------------------------------------------------------------------ * Test to determine the best read clock delay tuning bits. @@ -2571,6 +2565,16 @@ calibration_loop: mfsdram(SDRAM_RQDC, rqdc_reg); mtsdram(SDRAM_RQDC, (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) | SDRAM_RQDC_RQFD_ENCODE(rqfd_start)); +#else /* CONFIG_DDR_RQDC_FIXED */ + /* + * On Katmai the complete auto-calibration somehow doesn't seem to + * produce the best results, meaning optimal values for RQFD/RFFD. + * This was discovered by GDA using a high bandwidth scope, + * analyzing the DDR2 signals. GDA provided a fixed value for RQFD, + * so now on Katmai "only" RFFD is auto-calibrated. + */ + mtsdram(SDRAM_RQDC, CONFIG_DDR_RQDC_FIXED); +#endif /* CONFIG_DDR_RQDC_FIXED */ max_start = 0; min_end = 0; @@ -2655,6 +2659,7 @@ calibration_loop: /* now fix RFDC[RFFD] found and find RQDC[RQFD] */ mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average)); +#if !defined(CONFIG_DDR_RQDC_FIXED) max_pass_length = 0; max_start = 0; max_end = 0; @@ -2727,8 +2732,6 @@ calibration_loop: spd_ddr_init_hang (); } - blank_string(strlen(str)); - if (rqfd_average < 0) rqfd_average = 0; @@ -2739,12 +2742,31 @@ calibration_loop: (rqdc_reg & ~SDRAM_RQDC_RQFD_MASK) | SDRAM_RQDC_RQFD_ENCODE(rqfd_average)); + blank_string(strlen(str)); +#endif /* CONFIG_DDR_RQDC_FIXED */ + + /* + * Now complete RDSS configuration as mentioned on page 7 of the AMCC + * PowerPC440SP/SPe DDR2 application note: + * "DDR1/DDR2 Initialization Sequence and Dynamic Tuning" + */ + mfsdram(SDRAM_RTSR, val); + if ((val & SDRAM_RTSR_TRK1SM_MASK) == SDRAM_RTSR_TRK1SM_ATPLS1) { + mfsdram(SDRAM_RDCC, val); + if ((val & SDRAM_RDCC_RDSS_MASK) != SDRAM_RDCC_RDSS_T4) { + val += 0x40000000; + mtsdram(SDRAM_RDCC, val); + } + } + mfsdram(SDRAM_DLCR, val); debug("%s[%d] DLCR: 0x%08X\n", __FUNCTION__, __LINE__, val); mfsdram(SDRAM_RQDC, val); debug("%s[%d] RQDC: 0x%08X\n", __FUNCTION__, __LINE__, val); mfsdram(SDRAM_RFDC, val); debug("%s[%d] RFDC: 0x%08X\n", __FUNCTION__, __LINE__, val); + mfsdram(SDRAM_RDCC, val); + debug("%s[%d] RDCC: 0x%08X\n", __FUNCTION__, __LINE__, val); } #else /* calibration test with hardvalues */ /*-----------------------------------------------------------------------------+ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 0aa4f2dcc05..78c794a05de 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -111,6 +111,7 @@ #define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ #define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/ #define CONFIG_DDR_ECC 1 /* with ECC support */ +#define CONFIG_DDR_RQDC_FIXED 0x80000038 /* optimal value found by GDA*/ #undef CONFIG_STRESS /*----------------------------------------------------------------------- diff --git a/include/ppc440.h b/include/ppc440.h index 90e56b0989e..bfd1e10338d 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -492,6 +492,7 @@ #define SDRAM_ECCCR 0x98 /* ECC error status */ #define SDRAM_CID 0xA4 /* core ID */ #define SDRAM_RID 0xA8 /* revision ID */ +#define SDRAM_RTSR 0xB1 /* run time status tracking */ /*-----------------------------------------------------------------------------+ | Memory Controller Status @@ -605,8 +606,8 @@ #define SDRAM_RFDC_ARSE_ENABLE 0x00000000 #define SDRAM_RFDC_RFOS_MASK 0x007F0000 #define SDRAM_RFDC_RFOS_ENCODE(n) ((((unsigned long)(n))&0x7F)<<16) -#define SDRAM_RFDC_RFFD_MASK 0x000003FF -#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x3FF)<<0) +#define SDRAM_RFDC_RFFD_MASK 0x000007FF +#define SDRAM_RFDC_RFFD_ENCODE(n) ((((unsigned long)(n))&0x7FF)<<0) #define SDRAM_RFDC_RFFD_MAX 0x7FF @@ -690,6 +691,7 @@ #define SDRAM_CLKTR_CLKP_MASK 0xC0000000 #define SDRAM_CLKTR_CLKP_0_DEG 0x00000000 #define SDRAM_CLKTR_CLKP_180_DEG_ADV 0x80000000 +#define SDRAM_CLKTR_CLKP_90_DEG_ADV 0x40000000 /*-----------------------------------------------------------------------------+ | SDRAM Write Timing Register @@ -790,6 +792,12 @@ #define SDRAM_BXCF_M_BE_DISABLE 0x00000000 /* Memory Bank Enable */ #define SDRAM_BXCF_M_BE_ENABLE 0x00000001 /* Memory Bank Enable */ +#define SDRAM_RTSR_TRK1SM_MASK 0xC0000000 /* Tracking State Mach 1*/ +#define SDRAM_RTSR_TRK1SM_ATBASE 0x00000000 /* atbase state */ +#define SDRAM_RTSR_TRK1SM_MISSED 0x40000000 /* missed state */ +#define SDRAM_RTSR_TRK1SM_ATPLS1 0x80000000 /* atpls1 state */ +#define SDRAM_RTSR_TRK1SM_RESET 0xC0000000 /* reset state */ + #define SDR0_MFR_FIXD 0x10000000 /* Workaround for PCI/DMA */ #endif /* CONFIG_440SPE */ -- cgit v1.3.1 From b2893e1fcb28fad8c8b317104df8cee0142c7631 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Mon, 5 Nov 2007 09:34:06 -0600 Subject: 83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the currently-defined 83xx boards. This change guarantees that the environment will be located on the first flash sector after the U-Boot image. Signed-off-by: Timur Tabi Signed-off-by: Kim Phillips --- include/configs/MPC8313ERDB.h | 3 ++- include/configs/MPC8323ERDB.h | 5 +++-- include/configs/MPC832XEMDS.h | 5 +++-- include/configs/MPC8349EMDS.h | 2 +- include/configs/MPC8349ITX.h | 3 ++- include/configs/MPC8360EMDS.h | 5 +++-- 6 files changed, 14 insertions(+), 9 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 6568fe13b85..0c3bc16c9cb 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -178,6 +178,7 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ @@ -326,7 +327,7 @@ */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 376973b94da..558f94bb77a 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -116,6 +116,7 @@ #undef CFG_RAMBOOT #endif +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ @@ -354,8 +355,8 @@ */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CFG_ENV_SECT_SIZE 0x20000 #define CFG_ENV_SIZE 0x2000 #else #define CFG_NO_FLASH 1 /* Flash is not usable now */ diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index c9c6d88cf01..5345fc62f80 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -145,6 +145,7 @@ #undef CFG_RAMBOOT #endif +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ @@ -410,8 +411,8 @@ */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CFG_ENV_SECT_SIZE 0x20000 #define CFG_ENV_SIZE 0x2000 #else #define CFG_NO_FLASH 1 /* Flash is not usable now */ diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 92555bac422..7d5b17b50b1 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -456,7 +456,7 @@ */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 54cab528bde..2a2e753c87d 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -261,6 +261,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ @@ -404,8 +405,8 @@ boards, we say we have two, but don't display a message if we find only one. */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for environment */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + (4 * CFG_ENV_SECT_SIZE)) #define CFG_ENV_SIZE 0x2000 #else #define CFG_NO_FLASH /* Flash is not usable now */ diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 41f062ce72e..8098951c5b9 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -170,6 +170,7 @@ #undef CFG_RAMBOOT #endif +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ @@ -443,8 +444,8 @@ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CFG_ENV_SECT_SIZE 0x20000 #define CFG_ENV_SIZE 0x2000 #else #define CFG_NO_FLASH 1 /* Flash is not usable now */ -- cgit v1.3.1 From 03051c3d35c9981ceaa059005660e699f3eacf1c Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Tue, 18 Sep 2007 12:36:11 +0800 Subject: mpc83xx: Add the support of MPC837x SoC The MPC837x SoC including e300c4 core and new IP blocks, such as SDHC, PCI Express and SATA controller. Signed-off-by: Dave Liu --- cpu/mpc83xx/cpu.c | 24 +++++- cpu/mpc83xx/speed.c | 167 +++++++++++++++++++++++++++++++++------- include/asm-ppc/global_data.h | 10 ++- include/asm-ppc/immap_83xx.h | 84 +++++++++++++++++++- include/mpc83xx.h | 174 +++++++++++++++++++++++++++++++++++++----- 5 files changed, 406 insertions(+), 53 deletions(-) (limited to 'include') diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index f1ea17d5a52..98236ef5094 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -65,6 +65,10 @@ int checkcpu(void) printf("e300c3, "); break; + case PVR_E300C4: + printf("e300c4, "); + break; + default: printf("Unknown core, "); } @@ -149,6 +153,24 @@ int checkcpu(void) case SPR_8313E_REV10: puts("MPC8313E, "); break; + case SPR_8379E_REV10: + puts("MPC8379E, "); + break; + case SPR_8379_REV10: + puts("MPC8379, "); + break; + case SPR_8378E_REV10: + puts("MPC8378E, "); + break; + case SPR_8378_REV10: + puts("MPC8378, "); + break; + case SPR_8377E_REV10: + puts("MPC8377E, "); + break; + case SPR_8377_REV10: + puts("MPC8377, "); + break; default: printf("Rev: Unknown revision number:%08x\n" "Warning: Unsupported cpu revision!\n",spridr); diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c index cba57fadb99..23dfb304149 100644 --- a/cpu/mpc83xx/speed.c +++ b/cpu/mpc83xx/speed.c @@ -2,7 +2,7 @@ * (C) Copyright 2000-2002 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -100,7 +100,7 @@ int get_clocks(void) u32 lcrr; u32 csb_clk; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; @@ -112,6 +112,9 @@ int get_clocks(void) u32 i2c1_clk; #if !defined(CONFIG_MPC832X) u32 i2c2_clk; +#endif +#if defined(CONFIG_MPC837X) + u32 sdhc_clk; #endif u32 enc_clk; u32 lbiu_clk; @@ -126,6 +129,11 @@ int get_clocks(void) u32 qe_clk; u32 brg_clk; #endif +#if defined(CONFIG_MPC837X) + u32 pciexp1_clk; + u32 pciexp2_clk; + u32 sata_clk; +#endif if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) return -1; @@ -151,7 +159,7 @@ int get_clocks(void) sccr = im->clk.sccr; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) switch ((sccr & SCCR_TSEC1CM) >> SCCR_TSEC1CM_SHIFT) { case 0: tsec1_clk = 0; @@ -167,7 +175,7 @@ int get_clocks(void) break; default: /* unkown SCCR_TSEC1CM value */ - return -4; + return -2; } switch ((sccr & SCCR_USBDRCM) >> SCCR_USBDRCM_SHIFT) { @@ -185,11 +193,11 @@ int get_clocks(void) break; default: /* unkown SCCR_USBDRCM value */ - return -8; + return -3; } #endif -#if defined(CONFIG_MPC834X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) { case 0: tsec2_clk = 0; @@ -205,11 +213,18 @@ int get_clocks(void) break; default: /* unkown SCCR_TSEC2CM value */ - return -5; + return -4; } +#elif defined(CONFIG_MPC831X) + tsec2_clk = tsec1_clk; - i2c1_clk = tsec2_clk; + if (!(sccr & SCCR_TSEC1ON)) + tsec1_clk = 0; + if (!(sccr & SCCR_TSEC2ON)) + tsec2_clk = 0; +#endif +#if defined(CONFIG_MPC834X) switch ((sccr & SCCR_USBMPHCM) >> SCCR_USBMPHCM_SHIFT) { case 0: usbmph_clk = 0; @@ -225,7 +240,7 @@ int get_clocks(void) break; default: /* unkown SCCR_USBMPHCM value */ - return -7; + return -5; } if (usbmph_clk != 0 && usbdr_clk != 0 && usbmph_clk != usbdr_clk) { @@ -233,42 +248,120 @@ int get_clocks(void) * USB DR clock is not disabled then * USB MPH & USB DR must have the same rate */ - return -9; + return -6; + } +#endif + switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { + case 0: + enc_clk = 0; + break; + case 1: + enc_clk = csb_clk; + break; + case 2: + enc_clk = csb_clk / 2; + break; + case 3: + enc_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_ENCCM value */ + return -7; } -#elif defined(CONFIG_MPC831X) - tsec2_clk = tsec1_clk; - if (!(sccr & SCCR_TSEC1ON)) - tsec1_clk = 0; - if (!(sccr & SCCR_TSEC2ON)) - tsec2_clk = 0; +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_SDHCCM) >> SCCR_SDHCCM_SHIFT) { + case 0: + sdhc_clk = 0; + break; + case 1: + sdhc_clk = csb_clk; + break; + case 2: + sdhc_clk = csb_clk / 2; + break; + case 3: + sdhc_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_SDHCCM value */ + return -8; + } #endif -#if !defined(CONFIG_MPC834X) +#if defined(CONFIG_MPC834X) + i2c1_clk = tsec2_clk; +#elif defined(CONFIG_MPC8360) i2c1_clk = csb_clk; +#elif defined(CONFIG_MPC832X) + i2c1_clk = enc_clk; +#elif defined(CONFIG_MPC831X) + i2c1_clk = enc_clk; +#elif defined(CONFIG_MPC837X) + i2c1_clk = sdhc_clk; #endif #if !defined(CONFIG_MPC832X) - i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ + i2c2_clk = csb_clk; /* i2c-2 clk is equal to csb clk */ #endif - switch ((sccr & SCCR_ENCCM) >> SCCR_ENCCM_SHIFT) { +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_PCIEXP1CM) >> SCCR_PCIEXP1CM_SHIFT) { case 0: - enc_clk = 0; + pciexp1_clk = 0; break; case 1: - enc_clk = csb_clk; + pciexp1_clk = csb_clk; break; case 2: - enc_clk = csb_clk / 2; + pciexp1_clk = csb_clk / 2; break; case 3: - enc_clk = csb_clk / 3; + pciexp1_clk = csb_clk / 3; break; default: - /* unkown SCCR_ENCCM value */ - return -6; + /* unkown SCCR_PCIEXP1CM value */ + return -9; } + switch ((sccr & SCCR_PCIEXP2CM) >> SCCR_PCIEXP2CM_SHIFT) { + case 0: + pciexp2_clk = 0; + break; + case 1: + pciexp2_clk = csb_clk; + break; + case 2: + pciexp2_clk = csb_clk / 2; + break; + case 3: + pciexp2_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_PCIEXP2CM value */ + return -10; + } +#endif + +#if defined(CONFIG_MPC837X) + switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) { + case 0: + sata_clk = 0; + break; + case 1: + sata_clk = csb_clk; + break; + case 2: + sata_clk = csb_clk / 2; + break; + case 3: + sata_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_SATA1CM value */ + return -11; + } +#endif + lbiu_clk = csb_clk * (1 + ((im->reset.rcwl & HRCWL_LBIUCM) >> HRCWL_LBIUCM_SHIFT)); lcrr = (im->lbus.lcrr & LCRR_CLKDIV) >> LCRR_CLKDIV_SHIFT; @@ -280,7 +373,7 @@ int get_clocks(void) break; default: /* unknown lcrr */ - return -10; + return -12; } ddr_clk = csb_clk * @@ -316,7 +409,7 @@ int get_clocks(void) break; default: /* unkown core to csb ratio */ - return -12; + return -13; } #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) @@ -327,13 +420,16 @@ int get_clocks(void) #endif gd->csb_clk = csb_clk; -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) gd->tsec1_clk = tsec1_clk; gd->tsec2_clk = tsec2_clk; gd->usbdr_clk = usbdr_clk; #endif #if defined(CONFIG_MPC834X) gd->usbmph_clk = usbmph_clk; +#endif +#if defined(CONFIG_MPC837X) + gd->sdhc_clk = sdhc_clk; #endif gd->core_clk = core_clk; gd->i2c1_clk = i2c1_clk; @@ -350,6 +446,11 @@ int get_clocks(void) #if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) gd->qe_clk = qe_clk; gd->brg_clk = brg_clk; +#endif +#if defined(CONFIG_MPC837X) + gd->pciexp1_clk = pciexp1_clk; + gd->pciexp2_clk = pciexp2_clk; + gd->sata_clk = sata_clk; #endif gd->pci_clk = pci_sync_in; gd->cpu_clk = gd->core_clk; @@ -387,13 +488,21 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if !defined(CONFIG_MPC832X) printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000); #endif -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC837X) + printf(" SDHC: %4d MHz\n", gd->sdhc_clk / 1000000); +#endif +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) printf(" TSEC1: %4d MHz\n", gd->tsec1_clk / 1000000); printf(" TSEC2: %4d MHz\n", gd->tsec2_clk / 1000000); printf(" USB DR: %4d MHz\n", gd->usbdr_clk / 1000000); #endif #if defined(CONFIG_MPC834X) printf(" USB MPH: %4d MHz\n", gd->usbmph_clk / 1000000); +#endif +#if defined(CONFIG_MPC837X) + printf(" PCIEXP1: %4d MHz\n", gd->pciexp1_clk / 1000000); + printf(" PCIEXP2: %4d MHz\n", gd->pciexp2_clk / 1000000); + printf(" SATA: %4d MHz\n", gd->sata_clk / 1000000); #endif return 0; } diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 05aee749494..6ce072f663d 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -55,7 +55,7 @@ typedef struct global_data { #if defined(CONFIG_MPC83XX) /* There are other clocks in the MPC83XX */ u32 csb_clk; -#if defined (CONFIG_MPC834X) || defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) u32 tsec1_clk; u32 tsec2_clk; u32 usbdr_clk; @@ -63,6 +63,9 @@ typedef struct global_data { #if defined (CONFIG_MPC834X) u32 usbmph_clk; #endif /* CONFIG_MPC834X */ +#if defined(CONFIG_MPC837X) + u32 sdhc_clk; +#endif u32 core_clk; u32 i2c1_clk; u32 i2c2_clk; @@ -71,6 +74,11 @@ typedef struct global_data { u32 lclk_clk; u32 ddr_clk; u32 pci_clk; +#if defined(CONFIG_MPC837X) + u32 pciexp1_clk; + u32 pciexp2_clk; + u32 sata_clk; +#endif #if defined(CONFIG_MPC8360) u32 ddr_sec_clk; #endif /* CONFIG_MPC8360 */ diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 0de93385f3f..75171115b68 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2004-2006 Freescale Semiconductor, Inc. + * (C) Copyright 2004-2007 Freescale Semiconductor, Inc. * * MPC83xx Internal Memory Map * @@ -63,7 +63,8 @@ typedef struct sysconf83xx { u8 res6[0x0C]; u32 ddrcdr; /* DDR Control Driver Register */ u32 ddrdsr; /* DDR Debug Status Register */ - u8 res7[0xD0]; + u32 obir; /* Output Buffer Impedance Register */ + u8 res7[0xCC]; } sysconf83xx_t; /* @@ -553,6 +554,41 @@ typedef struct security83xx { u8 fixme[0x10000]; } security83xx_t; +/* + * PCI Express + */ +typedef struct pex83xx { + u8 fixme[0x1000]; +} pex83xx_t; + +/* + * SATA + */ +typedef struct sata83xx { + u8 fixme[0x1000]; +} sata83xx_t; + +/* + * eSDHC + */ +typedef struct sdhc83xx { + u8 fixme[0x1000]; +} sdhc83xx_t; + +/* + * SerDes + */ +typedef struct serdes83xx { + u8 fixme[0x100]; +} serdes83xx_t; + +/* + * On Chip ROM + */ +typedef struct rom83xx { + u8 mem[0x10000]; +} rom83xx_t; + #if defined(CONFIG_MPC834X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ @@ -625,6 +661,50 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; +#elif defined(CONFIG_MPC837X) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[2]; /* Global Timers Module */ + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + gpio83xx_t gpio[2]; /* General purpose I/O module */ + u8 res0[0x1200]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res1[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res2[0x900]; + lbus83xx_t lbus; /* Local Bus Controller Registers */ + u8 res3[0x1000]; + spi83xx_t spi; /* Serial Peripheral Interface */ + dma83xx_t dma; /* DMA */ + pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */ + u8 res4[0x80]; + ios83xx_t ios; /* Sequencer */ + pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */ + u8 res5[0xa00]; + pex83xx_t pciexp[2]; /* PCI Express Controller */ + u8 res6[0xd000]; + sata83xx_t sata[4]; /* SATA Controller */ + u8 res7[0x7000]; + usb83xx_t usb[1]; /* USB DR Controller */ + tsec83xx_t tsec[2]; + u8 res8[0x8000]; + sdhc83xx_t sdhc; /* SDHC Controller */ + u8 res9[0x1000]; + security83xx_t security; + u8 res10[0xA3000]; + serdes83xx_t serdes[2]; /* SerDes Registers */ + u8 res11[0xCE00]; + rom83xx_t rom; /* On Chip ROM */ +} immap_t; + #elif defined(CONFIG_MPC8360) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 4d32c6a3764..4c230943c08 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -98,10 +98,17 @@ #define SPR_8321E_REV11 0x80660011 #define SPR_8321_REV11 0x80670011 -#define SPR_8311_REV10 0x80B30010 -#define SPR_8311E_REV10 0x80B20010 -#define SPR_8313_REV10 0x80B10010 #define SPR_8313E_REV10 0x80B00010 +#define SPR_8313_REV10 0x80B10010 +#define SPR_8311E_REV10 0x80B20010 +#define SPR_8311_REV10 0x80B30010 + +#define SPR_8379E_REV10 0x80C20010 +#define SPR_8379_REV10 0x80C30010 +#define SPR_8378E_REV10 0x80C40010 +#define SPR_8378_REV10 0x80C50010 +#define SPR_8377E_REV10 0x80C60010 +#define SPR_8377_REV10 0x80C70010 /* SPCR - System Priority Configuration Register */ @@ -130,8 +137,8 @@ #define SPCR_TSEC2EP 0x00000003 /* TSEC2 emergency priority */ #define SPCR_TSEC2EP_SHIFT (31-31) -#elif defined(CONFIG_MPC831X) -/* SPCR bits - MPC831x specific */ +#elif defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) +/* SPCR bits - MPC831x and MPC837x specific */ #define SPCR_TSECDP 0x00003000 /* TSEC data priority */ #define SPCR_TSECDP_SHIFT (31-19) #define SPCR_TSECEP 0x00000C00 /* TSEC emergency priority */ @@ -242,6 +249,55 @@ #define SICRH_TSOBI1 0x00000002 #define SICRH_TSOBI2 0x00000001 +#elif defined(CONFIG_MPC837X) +/* SICRL bits - MPC837x specific */ +#define SICRL_USB_A 0xC0000000 +#define SICRL_USB_B 0x30000000 +#define SICRL_UART 0x0C000000 +#define SICRL_GPIO_A 0x02000000 +#define SICRL_GPIO_B 0x01000000 +#define SICRL_GPIO_C 0x00800000 +#define SICRL_GPIO_D 0x00400000 +#define SICRL_GPIO_E 0x00200000 +#define SICRL_GPIO_F 0x00180000 +#define SICRL_GPIO_G 0x00040000 +#define SICRL_GPIO_H 0x00020000 +#define SICRL_GPIO_I 0x00010000 +#define SICRL_GPIO_J 0x00008000 +#define SICRL_GPIO_K 0x00004000 +#define SICRL_GPIO_L 0x00003000 +#define SICRL_DMA_A 0x00000800 +#define SICRL_DMA_B 0x00000400 +#define SICRL_DMA_C 0x00000200 +#define SICRL_DMA_D 0x00000100 +#define SICRL_DMA_E 0x00000080 +#define SICRL_DMA_F 0x00000040 +#define SICRL_DMA_G 0x00000020 +#define SICRL_DMA_H 0x00000010 +#define SICRL_DMA_I 0x00000008 +#define SICRL_DMA_J 0x00000004 +#define SICRL_LDP_A 0x00000002 +#define SICRL_LDP_B 0x00000001 + +/* SICRH bits - MPC837x specific */ +#define SICRH_DDR 0x80000000 +#define SICRH_TSEC1_A 0x10000000 +#define SICRH_TSEC1_B 0x08000000 +#define SICRH_TSEC2_A 0x00400000 +#define SICRH_TSEC2_B 0x00200000 +#define SICRH_TSEC2_C 0x00100000 +#define SICRH_TSEC2_D 0x00080000 +#define SICRH_TSEC2_E 0x00040000 +#define SICRH_TMR 0x00010000 +#define SICRH_GPIO2_A 0x00008000 +#define SICRH_GPIO2_B 0x00004000 +#define SICRH_GPIO2_C 0x00002000 +#define SICRH_GPIO2_D 0x00001000 +#define SICRH_GPIO2_E 0x00000C00 +#define SICRH_GPIO2_F 0x00000300 +#define SICRH_GPIO2_G 0x000000C0 +#define SICRH_GPIO2_H 0x00000030 +#define SICRH_SPI 0x00000003 #endif /* SWCRR - System Watchdog Control Register @@ -390,6 +446,14 @@ #define HRCWL_CE_TO_PLL_1X29 0x0000001D #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F + +#elif defined(CONFIG_MPC837X) +#define HRCWL_SVCOD 0x30000000 +#define HRCWL_SVCOD_SHIFT 28 +#define HRCWL_SVCOD_DIV_4 0x00000000 +#define HRCWL_SVCOD_DIV_8 0x10000000 +#define HRCWL_SVCOD_DIV_2 0x20000000 +#define HRCWL_SVCOD_DIV_1 0x30000000 #endif /* HRCWH - Hardware Reset Configuration Word High @@ -436,11 +500,14 @@ #if defined(CONFIG_MPC834X) #define HRCWH_ROM_LOC_PCI2 0x00200000 #endif +#if defined(CONIFG_MPC837X) +#define HRCWH_ROM_LOC_ON_CHIP_ROM 0x00300000 +#endif #define HRCWH_ROM_LOC_LOCAL_8BIT 0x00500000 #define HRCWH_ROM_LOC_LOCAL_16BIT 0x00600000 #define HRCWH_ROM_LOC_LOCAL_32BIT 0x00700000 -#if defined(CONFIG_MPC831X) +#if defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) #define HRCWH_ROM_LOC_NAND_SP_8BIT 0x00100000 #define HRCWH_ROM_LOC_NAND_SP_16BIT 0x00200000 #define HRCWH_ROM_LOC_NAND_LP_8BIT 0x00500000 @@ -489,8 +556,13 @@ /* RSR - Reset Status Register */ +#if defined(CONFIG_MPC837X) +#define RSR_RSTSRC 0xF0000000 /* Reset source */ +#define RSR_RSTSRC_SHIFT 28 +#else #define RSR_RSTSRC 0xE0000000 /* Reset source */ #define RSR_RSTSRC_SHIFT 29 +#endif #define RSR_BSF 0x00010000 /* Boot seq. fail */ #define RSR_BSF_SHIFT 16 #define RSR_SWSR 0x00002000 /* software soft reset */ @@ -577,8 +649,8 @@ #define SCCR_PCICM 0x00010000 #define SCCR_PCICM_SHIFT 16 -/* SCCR bits - MPC8349 specific */ -#ifdef CONFIG_MPC834X +#if defined(CONFIG_MPC834X) +/* SCCR bits - MPC834x specific */ #define SCCR_TSEC1CM 0xc0000000 #define SCCR_TSEC1CM_SHIFT 30 #define SCCR_TSEC1CM_0 0x00000000 @@ -593,6 +665,18 @@ #define SCCR_TSEC2CM_2 0x20000000 #define SCCR_TSEC2CM_3 0x30000000 +/* The MPH must have the same clock ratio as DR, unless its clock disabled */ +#define SCCR_USBMPHCM 0x00c00000 +#define SCCR_USBMPHCM_SHIFT 22 +#define SCCR_USBDRCM 0x00300000 +#define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBCM 0x00f00000 +#define SCCR_USBCM_SHIFT 20 +#define SCCR_USBCM_0 0x00000000 +#define SCCR_USBCM_1 0x00500000 +#define SCCR_USBCM_2 0x00A00000 +#define SCCR_USBCM_3 0x00F00000 + #elif defined(CONFIG_MPC831X) /* TSEC1 bits are for TSEC2 as well */ #define SCCR_TSEC1CM 0xc0000000 @@ -606,17 +690,67 @@ #define SCCR_TSEC2ON 0x10000000 #define SCCR_TSEC2ON_SHIFT 28 -#endif - -#define SCCR_USBMPHCM 0x00c00000 -#define SCCR_USBMPHCM_SHIFT 22 #define SCCR_USBDRCM 0x00300000 #define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00100000 +#define SCCR_USBDRCM_2 0x00200000 +#define SCCR_USBDRCM_3 0x00300000 -#define SCCR_USBCM_0 0x00000000 -#define SCCR_USBCM_1 0x00500000 -#define SCCR_USBCM_2 0x00A00000 -#define SCCR_USBCM_3 0x00F00000 +#elif defined(CONFIG_MPC837X) +/* SCCR bits - MPC837x specific */ +#define SCCR_TSEC1CM 0xc0000000 +#define SCCR_TSEC1CM_SHIFT 30 +#define SCCR_TSEC1CM_0 0x00000000 +#define SCCR_TSEC1CM_1 0x40000000 +#define SCCR_TSEC1CM_2 0x80000000 +#define SCCR_TSEC1CM_3 0xC0000000 + +#define SCCR_TSEC2CM 0x30000000 +#define SCCR_TSEC2CM_SHIFT 28 +#define SCCR_TSEC2CM_0 0x00000000 +#define SCCR_TSEC2CM_1 0x10000000 +#define SCCR_TSEC2CM_2 0x20000000 +#define SCCR_TSEC2CM_3 0x30000000 + +#define SCCR_SDHCCM 0x0c000000 +#define SCCR_SDHCCM_SHIFT 26 +#define SCCR_SDHCCM_0 0x00000000 +#define SCCR_SDHCCM_1 0x04000000 +#define SCCR_SDHCCM_2 0x08000000 +#define SCCR_SDHCCM_3 0x0c000000 + +#define SCCR_USBDRCM 0x00c00000 +#define SCCR_USBDRCM_SHIFT 22 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00400000 +#define SCCR_USBDRCM_2 0x00800000 +#define SCCR_USBDRCM_3 0x00c00000 + +#define SCCR_PCIEXP1CM 0x00300000 +#define SCCR_PCIEXP1CM_SHIFT 20 +#define SCCR_PCIEXP1CM_0 0x00000000 +#define SCCR_PCIEXP1CM_1 0x00100000 +#define SCCR_PCIEXP1CM_2 0x00200000 +#define SCCR_PCIEXP1CM_3 0x00300000 + +#define SCCR_PCIEXP2CM 0x000c0000 +#define SCCR_PCIEXP2CM_SHIFT 18 +#define SCCR_PCIEXP2CM_0 0x00000000 +#define SCCR_PCIEXP2CM_1 0x00040000 +#define SCCR_PCIEXP2CM_2 0x00080000 +#define SCCR_PCIEXP2CM_3 0x000c0000 + +/* All of the four SATA controllers must have the same clock ratio */ +#define SCCR_SATA1CM 0x000000c0 +#define SCCR_SATA1CM_SHIFT 6 +#define SCCR_SATACM 0x000000ff +#define SCCR_SATACM_SHIFT 0 +#define SCCR_SATACM_0 0x00000000 +#define SCCR_SATACM_1 0x00000055 +#define SCCR_SATACM_2 0x000000aa +#define SCCR_SATACM_3 0x000000ff +#endif /* CSn_BDNS - Chip Select memory Bounds Register */ @@ -860,7 +994,7 @@ #define BR_MS_UPMA 0x00000080 /* UPMA */ #define BR_MS_UPMB 0x000000A0 /* UPMB */ #define BR_MS_UPMC 0x000000C0 /* UPMC */ -#if defined(CONFIG_MPC8360) || defined(CONFIG_MPC832X) +#if !defined(CONFIG_MPC834X) #define BR_ATOM 0x0000000C #define BR_ATOM_SHIFT 2 #endif @@ -869,7 +1003,7 @@ #if defined(CONFIG_MPC834X) #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_V) -#elif defined(CONFIG_MPC8360) +#else #define BR_RES ~(BR_BA | BR_PS | BR_DECC | BR_WP | BR_MSEL | BR_ATOM | BR_V) #endif @@ -1255,7 +1389,7 @@ #define LTESR_CS 0x00080000 #define LTESR_CC 0x00000001 -/* DDR Control Driver Register +/* DDRCDR - DDR Control Driver Register */ #define DDRCDR_EN 0x40000000 #define DDRCDR_PZ 0x3C000000 -- cgit v1.3.1 From 555da61702771fe0f76f3de23b4e7590f3704161 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Tue, 18 Sep 2007 12:36:58 +0800 Subject: mpc83xx: Add the support of MPC8315E SoC The MPC8315E SoC including e300c3 core and new IP blocks, such as TDM, PCI Express and SATA controller. Signed-off-by: Dave Liu --- cpu/mpc83xx/cpu.c | 12 ++++++ cpu/mpc83xx/speed.c | 40 +++++++++++++++++-- include/asm-ppc/global_data.h | 5 +++ include/asm-ppc/immap_83xx.h | 61 +++++++++++++++++++++++++++- include/mpc83xx.h | 93 ++++++++++++++++++++++++++++++++++++++++--- 5 files changed, 201 insertions(+), 10 deletions(-) (limited to 'include') diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index 98236ef5094..8d69d229050 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -153,6 +153,18 @@ int checkcpu(void) case SPR_8313E_REV10: puts("MPC8313E, "); break; + case SPR_8315E_REV10: + puts("MPC8315E, "); + break; + case SPR_8315_REV10: + puts("MPC8315, "); + break; + case SPR_8314E_REV10: + puts("MPC8314E, "); + break; + case SPR_8314_REV10: + puts("MPC8314, "); + break; case SPR_8379E_REV10: puts("MPC8379E, "); break; diff --git a/cpu/mpc83xx/speed.c b/cpu/mpc83xx/speed.c index 23dfb304149..4f5a8661816 100644 --- a/cpu/mpc83xx/speed.c +++ b/cpu/mpc83xx/speed.c @@ -113,6 +113,9 @@ int get_clocks(void) #if !defined(CONFIG_MPC832X) u32 i2c2_clk; #endif +#if defined(CONFIG_MPC8315) + u32 tdm_clk; +#endif #if defined(CONFIG_MPC837X) u32 sdhc_clk; #endif @@ -132,6 +135,8 @@ int get_clocks(void) #if defined(CONFIG_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) u32 sata_clk; #endif @@ -197,7 +202,7 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC834X) || defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) switch ((sccr & SCCR_TSEC2CM) >> SCCR_TSEC2CM_SHIFT) { case 0: tsec2_clk = 0; @@ -215,7 +220,7 @@ int get_clocks(void) /* unkown SCCR_TSEC2CM value */ return -4; } -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) tsec2_clk = tsec1_clk; if (!(sccr & SCCR_TSEC1ON)) @@ -288,6 +293,25 @@ int get_clocks(void) return -8; } #endif +#if defined(CONFIG_MPC8315) + switch ((sccr & SCCR_TDMCM) >> SCCR_TDMCM_SHIFT) { + case 0: + tdm_clk = 0; + break; + case 1: + tdm_clk = csb_clk; + break; + case 2: + tdm_clk = csb_clk / 2; + break; + case 3: + tdm_clk = csb_clk / 3; + break; + default: + /* unkown SCCR_TDMCM value */ + return -8; + } +#endif #if defined(CONFIG_MPC834X) i2c1_clk = tsec2_clk; @@ -342,7 +366,7 @@ int get_clocks(void) } #endif -#if defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) switch ((sccr & SCCR_SATA1CM) >> SCCR_SATA1CM_SHIFT) { case 0: sata_clk = 0; @@ -428,6 +452,9 @@ int get_clocks(void) #if defined(CONFIG_MPC834X) gd->usbmph_clk = usbmph_clk; #endif +#if defined(CONFIG_MPC8315) + gd->tdm_clk = tdm_clk; +#endif #if defined(CONFIG_MPC837X) gd->sdhc_clk = sdhc_clk; #endif @@ -450,6 +477,8 @@ int get_clocks(void) #if defined(CONFIG_MPC837X) gd->pciexp1_clk = pciexp1_clk; gd->pciexp2_clk = pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) gd->sata_clk = sata_clk; #endif gd->pci_clk = pci_sync_in; @@ -488,6 +517,9 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if !defined(CONFIG_MPC832X) printf(" I2C2: %4d MHz\n", gd->i2c2_clk / 1000000); #endif +#if defined(CONFIG_MPC8315) + printf(" TDM: %4d MHz\n", gd->tdm_clk / 1000000); +#endif #if defined(CONFIG_MPC837X) printf(" SDHC: %4d MHz\n", gd->sdhc_clk / 1000000); #endif @@ -502,6 +534,8 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) #if defined(CONFIG_MPC837X) printf(" PCIEXP1: %4d MHz\n", gd->pciexp1_clk / 1000000); printf(" PCIEXP2: %4d MHz\n", gd->pciexp2_clk / 1000000); +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) printf(" SATA: %4d MHz\n", gd->sata_clk / 1000000); #endif return 0; diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 6ce072f663d..91acf9b7cb2 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -63,6 +63,9 @@ typedef struct global_data { #if defined (CONFIG_MPC834X) u32 usbmph_clk; #endif /* CONFIG_MPC834X */ +#if defined(CONFIG_MPC815) + u32 tdm_clk; +#endif #if defined(CONFIG_MPC837X) u32 sdhc_clk; #endif @@ -77,6 +80,8 @@ typedef struct global_data { #if defined(CONFIG_MPC837X) u32 pciexp1_clk; u32 pciexp2_clk; +#endif +#if defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) u32 sata_clk; #endif #if defined(CONFIG_MPC8360) diff --git a/include/asm-ppc/immap_83xx.h b/include/asm-ppc/immap_83xx.h index 75171115b68..34ea2959902 100644 --- a/include/asm-ppc/immap_83xx.h +++ b/include/asm-ppc/immap_83xx.h @@ -589,6 +589,20 @@ typedef struct rom83xx { u8 mem[0x10000]; } rom83xx_t; +/* + * TDM + */ +typedef struct tdm83xx { + u8 fixme[0x200]; +} tdm83xx_t; + +/* + * TDM DMAC + */ +typedef struct tdmdmac83xx { + u8 fixme[0x2000]; +} tdmdmac83xx_t; + #if defined(CONFIG_MPC834X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ @@ -626,7 +640,7 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ @@ -661,6 +675,51 @@ typedef struct immap { u8 res7[0xC0000]; } immap_t; +#elif defined(CONFIG_MPC8315) +typedef struct immap { + sysconf83xx_t sysconf; /* System configuration */ + wdt83xx_t wdt; /* Watch Dog Timer (WDT) Registers */ + rtclk83xx_t rtc; /* Real Time Clock Module Registers */ + rtclk83xx_t pit; /* Periodic Interval Timer */ + gtm83xx_t gtm[2]; /* Global Timers Module */ + ipic83xx_t ipic; /* Integrated Programmable Interrupt Controller */ + arbiter83xx_t arbiter; /* System Arbiter Registers */ + reset83xx_t reset; /* Reset Module */ + clk83xx_t clk; /* System Clock Module */ + pmc83xx_t pmc; /* Power Management Control Module */ + gpio83xx_t gpio[1]; /* General purpose I/O module */ + u8 res0[0x1300]; + ddr83xx_t ddr; /* DDR Memory Controller Memory */ + fsl_i2c_t i2c[2]; /* I2C Controllers */ + u8 res1[0x1300]; + duart83xx_t duart[2]; /* DUART */ + u8 res2[0x900]; + lbus83xx_t lbus; /* Local Bus Controller Registers */ + u8 res3[0x1000]; + spi83xx_t spi; /* Serial Peripheral Interface */ + dma83xx_t dma; /* DMA */ + pciconf83xx_t pci_conf[1]; /* PCI Software Configuration Registers */ + u8 res4[0x80]; + ios83xx_t ios; /* Sequencer */ + pcictrl83xx_t pci_ctrl[1]; /* PCI Controller Control and Status Registers */ + u8 res5[0xa00]; + pex83xx_t pciexp[2]; /* PCI Express Controller */ + u8 res6[0xb000]; + tdm83xx_t tdm; /* TDM Controller */ + u8 res7[0x1e00]; + sata83xx_t sata[2]; /* SATA Controller */ + u8 res8[0x9000]; + usb83xx_t usb[1]; /* USB DR Controller */ + tsec83xx_t tsec[2]; + u8 res9[0x6000]; + tdmdmac83xx_t tdmdmac; /* TDM DMAC */ + u8 res10[0x2000]; + security83xx_t security; + u8 res11[0xA3000]; + serdes83xx_t serdes[1]; /* SerDes Registers */ + u8 res12[0x1CF00]; +} immap_t; + #elif defined(CONFIG_MPC837X) typedef struct immap { sysconf83xx_t sysconf; /* System configuration */ diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 4c230943c08..dba1aea4fa9 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -102,6 +102,10 @@ #define SPR_8313_REV10 0x80B10010 #define SPR_8311E_REV10 0x80B20010 #define SPR_8311_REV10 0x80B30010 +#define SPR_8315E_REV10 0x80B40010 +#define SPR_8315_REV10 0x80B50010 +#define SPR_8314E_REV10 0x80B60010 +#define SPR_8314_REV10 0x80B70010 #define SPR_8379E_REV10 0x80C20010 #define SPR_8379_REV10 0x80C30010 @@ -220,8 +224,8 @@ #define SICRL_URT_CTPR 0x06000000 #define SICRL_IRQ_CTPR 0x00C00000 -#elif defined(CONFIG_MPC831X) -/* SICRL bits - MPC831x specific */ +#elif defined(CONFIG_MPC8313) +/* SICRL bits - MPC8313 specific */ #define SICRL_LBC 0x30000000 #define SICRL_UART 0x0C000000 #define SICRL_SPI_A 0x03000000 @@ -232,7 +236,7 @@ #define SICRL_ETSEC1_A 0x0000000C #define SICRL_ETSEC2_A 0x00000003 -/* SICRH bits - MPC831x specific */ +/* SICRH bits - MPC8313 specific */ #define SICRH_INTR_A 0x02000000 #define SICRH_INTR_B 0x00C00000 #define SICRH_IIC 0x00300000 @@ -249,6 +253,41 @@ #define SICRH_TSOBI1 0x00000002 #define SICRH_TSOBI2 0x00000001 +#elif defined(CONFIG_MPC8315) +/* SICRL bits - MPC8315 specific */ +#define SICRL_DMA_CH0 0xc0000000 +#define SICRL_DMA_SPI 0x30000000 +#define SICRL_UART 0x0c000000 +#define SICRL_IRQ4 0x02000000 +#define SICRL_IRQ5 0x01800000 +#define SICRL_IRQ6_7 0x00400000 +#define SICRL_IIC1 0x00300000 +#define SICRL_TDM 0x000c0000 +#define SICRL_TDM_SHARED 0x00030000 +#define SICRL_PCI_A 0x0000c000 +#define SICRL_ELBC_A 0x00003000 +#define SICRL_ETSEC1_A 0x000000c0 +#define SICRL_ETSEC1_B 0x00000030 +#define SICRL_ETSEC1_C 0x0000000c +#define SICRL_TSEXPOBI 0x00000001 + +/* SICRH bits - MPC8315 specific */ +#define SICRH_GPIO_0 0xc0000000 +#define SICRH_GPIO_1 0x30000000 +#define SICRH_GPIO_2 0x0c000000 +#define SICRH_GPIO_3 0x03000000 +#define SICRH_GPIO_4 0x00c00000 +#define SICRH_GPIO_5 0x00300000 +#define SICRH_GPIO_6 0x000c0000 +#define SICRH_GPIO_7 0x00030000 +#define SICRH_GPIO_8 0x0000c000 +#define SICRH_GPIO_9 0x00003000 +#define SICRH_GPIO_10 0x00000c00 +#define SICRH_GPIO_11 0x00000300 +#define SICRH_ETSEC2_A 0x000000c0 +#define SICRH_TSOBI1 0x00000002 +#define SICRH_TSOBI2 0x00000001 + #elif defined(CONFIG_MPC837X) /* SICRL bits - MPC837x specific */ #define SICRL_USB_A 0xC0000000 @@ -447,7 +486,7 @@ #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F -#elif defined(CONFIG_MPC837X) +#elif defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) #define HRCWL_SVCOD 0x30000000 #define HRCWL_SVCOD_SHIFT 28 #define HRCWL_SVCOD_DIV_4 0x00000000 @@ -556,7 +595,7 @@ /* RSR - Reset Status Register */ -#if defined(CONFIG_MPC837X) +#if defined(CONFIG_MPC831X) || defined(CONFIG_MPC837X) #define RSR_RSTSRC 0xF0000000 /* Reset source */ #define RSR_RSTSRC_SHIFT 28 #else @@ -677,7 +716,7 @@ #define SCCR_USBCM_2 0x00A00000 #define SCCR_USBCM_3 0x00F00000 -#elif defined(CONFIG_MPC831X) +#elif defined(CONFIG_MPC8313) /* TSEC1 bits are for TSEC2 as well */ #define SCCR_TSEC1CM 0xc0000000 #define SCCR_TSEC1CM_SHIFT 30 @@ -697,6 +736,48 @@ #define SCCR_USBDRCM_2 0x00200000 #define SCCR_USBDRCM_3 0x00300000 +#elif defined(CONFIG_MPC8315) +/* SCCR bits - MPC8315 specific */ +#define SCCR_TSEC1CM 0xc0000000 +#define SCCR_TSEC1CM_SHIFT 30 +#define SCCR_TSEC1CM_0 0x00000000 +#define SCCR_TSEC1CM_1 0x40000000 +#define SCCR_TSEC1CM_2 0x80000000 +#define SCCR_TSEC1CM_3 0xC0000000 + +#define SCCR_TSEC2CM 0x30000000 +#define SCCR_TSEC2CM_SHIFT 28 +#define SCCR_TSEC2CM_0 0x00000000 +#define SCCR_TSEC2CM_1 0x10000000 +#define SCCR_TSEC2CM_2 0x20000000 +#define SCCR_TSEC2CM_3 0x30000000 + +#define SCCR_USBDRCM 0x00300000 +#define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBDRCM_0 0x00000000 +#define SCCR_USBDRCM_1 0x00100000 +#define SCCR_USBDRCM_2 0x00200000 +#define SCCR_USBDRCM_3 0x00300000 + +#define SCCR_PCIEXP1CM 0x00080000 +#define SCCR_PCIEXP2CM 0x00040000 + +#define SCCR_SATA1CM 0x0000c000 +#define SCCR_SATA1CM_SHIFT 14 +#define SCCR_SATACM 0x0000f000 +#define SCCR_SATACM_SHIFT 8 +#define SCCR_SATACM_0 0x00000000 +#define SCCR_SATACM_1 0x00005000 +#define SCCR_SATACM_2 0x0000a000 +#define SCCR_SATACM_3 0x0000f000 + +#define SCCR_TDMCM 0x000000c0 +#define SCCR_TDMCM_SHIFT 6 +#define SCCR_TDMCM_0 0x00000000 +#define SCCR_TDMCM_1 0x00000040 +#define SCCR_TDMCM_2 0x00000080 +#define SCCR_TDMCM_3 0x000000c0 + #elif defined(CONFIG_MPC837X) /* SCCR bits - MPC837x specific */ #define SCCR_TSEC1CM 0xc0000000 -- cgit v1.3.1 From 19580e660cc8da49f16536a8bd78c047c7bc12e5 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Tue, 18 Sep 2007 12:37:57 +0800 Subject: mpc83xx: Add the support of MPC837xEMDS board The MPC837xEMDS board support: * DDR2 400MHz hardcoded and SPD init * Local bus NOR Flash * I2C, UART, MII and RTC * eTSEC RGMII * PCI host Signed-off-by: Dave Liu --- Makefile | 10 + board/freescale/mpc837xemds/Makefile | 50 +++ board/freescale/mpc837xemds/config.mk | 28 ++ board/freescale/mpc837xemds/mpc837xemds.c | 144 +++++++ board/freescale/mpc837xemds/pci.c | 65 ++++ cpu/mpc83xx/cpu_init.c | 6 +- cpu/mpc83xx/spd_sdram.c | 7 +- drivers/net/tsec.c | 10 + include/configs/MPC837XEMDS.h | 605 ++++++++++++++++++++++++++++++ 9 files changed, 922 insertions(+), 3 deletions(-) create mode 100644 board/freescale/mpc837xemds/Makefile create mode 100644 board/freescale/mpc837xemds/config.mk create mode 100644 board/freescale/mpc837xemds/mpc837xemds.c create mode 100644 board/freescale/mpc837xemds/pci.c create mode 100644 include/configs/MPC837XEMDS.h (limited to 'include') diff --git a/Makefile b/Makefile index 35e90315f4c..dd995d30581 100644 --- a/Makefile +++ b/Makefile @@ -1922,6 +1922,16 @@ MPC8360EMDS_ATM_config: unconfig fi ; @$(MKCONFIG) -a MPC8360EMDS ppc mpc83xx mpc8360emds freescale +MPC837XEMDS_config \ +MPC837XEMDS_HOST_config: unconfig + @mkdir -p $(obj)include + @echo "" >$(obj)include/config.h ; \ + if [ "$(findstring _HOST_,$@)" ] ; then \ + echo -n "... PCI HOST " ; \ + echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \ + fi ; + @$(MKCONFIG) -a MPC837XEMDS ppc mpc83xx mpc837xemds freescale + sbc8349_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349 diff --git a/board/freescale/mpc837xemds/Makefile b/board/freescale/mpc837xemds/Makefile new file mode 100644 index 00000000000..5ec7a871d4d --- /dev/null +++ b/board/freescale/mpc837xemds/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o pci.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc837xemds/config.mk b/board/freescale/mpc837xemds/config.mk new file mode 100644 index 00000000000..63c5fc3c348 --- /dev/null +++ b/board/freescale/mpc837xemds/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# MPC837xEMDS +# + +TEXT_BASE = 0xFE000000 diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c new file mode 100644 index 00000000000..0e4ec0213b5 --- /dev/null +++ b/board/freescale/mpc837xemds/mpc837xemds.c @@ -0,0 +1,144 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Dave Liu + * + * CREDITS: Kim Phillips contribute to LIBFDT code + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include +#include +#include +#if defined(CONFIG_SPD_EEPROM) +#include +#endif +#if defined(CONFIG_OF_FLAT_TREE) +#include +#elif defined(CONFIG_OF_LIBFDT) +#include +#endif +#if defined(CONFIG_PQ_MDS_PIB) +#include "../common/pq-mds-pib.h" +#endif + +int board_early_init_f(void) +{ + u8 *bcsr = (u8 *)CFG_BCSR; + + /* Enable flash write */ + bcsr[0x9] &= ~0x04; + /* Clear all of the interrupt of BCSR */ + bcsr[0xe] = 0xff; + + return 0; +} + +int board_early_init_r(void) +{ +#ifdef CONFIG_PQ_MDS_PIB + pib_init(); +#endif + return 0; +} + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif +int fixed_sdram(void); + +long int initdram(int board_type) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im) + return -1; + +#if defined(CONFIG_SPD_EEPROM) + msize = spd_sdram(); +#else + msize = fixed_sdram(); +#endif + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + /* Initialize DDR ECC byte */ + ddr_enable_ecc(msize * 1024 * 1024); +#endif + + /* return total bus DDR size(bytes) */ + return (msize * 1024 * 1024); +} + +#if !defined(CONFIG_SPD_EEPROM) +/************************************************************************* + * fixed sdram init -- doesn't use serial presence detect. + ************************************************************************/ +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *) CFG_IMMR; + u32 msize = CFG_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12; + im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1); + +#if (CFG_DDR_SIZE != 512) +#warning Currenly any ddr size other than 512 is not supported +#endif + im->sysconf.ddrcdr = CFG_DDRCDR_VALUE; + udelay(50000); + + im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL; + udelay(1000); + + im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG; + udelay(1000); + + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE2; + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + __asm__ __volatile__("sync"); + udelay(1000); + + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + udelay(2000); + return CFG_DDR_SIZE; +} +#endif /*!CFG_SPD_EEPROM */ + +int checkboard(void) +{ + puts("Board: Freescale MPC837xEMDS\n"); + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ +#if defined(CONFIG_OF_FLAT_TREE) + u32 *p; + int len; + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +#endif + ft_cpu_setup(blob, bd); +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif +} +#endif /* CONFIG_OF_BOARD_SETUP */ diff --git a/board/freescale/mpc837xemds/pci.c b/board/freescale/mpc837xemds/pci.c new file mode 100644 index 00000000000..ab909790e5d --- /dev/null +++ b/board/freescale/mpc837xemds/pci.c @@ -0,0 +1,65 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_PCI) +static struct pci_region pci_regions[] = { + { + bus_start: CFG_PCI_MEM_BASE, + phys_start: CFG_PCI_MEM_PHYS, + size: CFG_PCI_MEM_SIZE, + flags: PCI_REGION_MEM | PCI_REGION_PREFETCH + }, + { + bus_start: CFG_PCI_MMIO_BASE, + phys_start: CFG_PCI_MMIO_PHYS, + size: CFG_PCI_MMIO_SIZE, + flags: PCI_REGION_MEM + }, + { + bus_start: CFG_PCI_IO_BASE, + phys_start: CFG_PCI_IO_PHYS, + size: CFG_PCI_IO_SIZE, + flags: PCI_REGION_IO + } +}; + +void pci_init_board(void) +{ + volatile immap_t *immr = (volatile immap_t *)CFG_IMMR; + volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; + volatile law83xx_t *pci_law = immr->sysconf.pcilaw; + struct pci_region *reg[] = { pci_regions }; + + /* Enable all 5 PCI_CLK_OUTPUTS */ + clk->occr |= 0xf8000000; + udelay(2000); + + /* Configure PCI Local Access Windows */ + pci_law[0].bar = CFG_PCI_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; + + pci_law[1].bar = CFG_PCI_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; + + udelay(2000); + + mpc83xx_pci_init(1, reg, 0); +} +#endif /* CONFIG_PCI */ diff --git a/cpu/mpc83xx/cpu_init.c b/cpu/mpc83xx/cpu_init.c index 722497966a1..2b92be01ad9 100644 --- a/cpu/mpc83xx/cpu_init.c +++ b/cpu/mpc83xx/cpu_init.c @@ -1,5 +1,5 @@ /* - * Copyright (C) 2004-2006 Freescale Semiconductor, Inc. + * Copyright (C) 2004-2007 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -155,6 +155,10 @@ void cpu_init_f (volatile immap_t * im) #ifdef CFG_DDRCDR im->sysconf.ddrcdr = CFG_DDRCDR; #endif + /* Output buffer impedance register */ +#ifdef CFG_OBIR + im->sysconf.obir = CFG_OBIR; +#endif #ifdef CONFIG_QE /* Config QE ioports */ diff --git a/cpu/mpc83xx/spd_sdram.c b/cpu/mpc83xx/spd_sdram.c index ee2d0385e45..29dd47078ec 100644 --- a/cpu/mpc83xx/spd_sdram.c +++ b/cpu/mpc83xx/spd_sdram.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2006 Freescale Semiconductor, Inc. + * (C) Copyright 2006-2007 Freescale Semiconductor, Inc. * * (C) Copyright 2006 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. @@ -198,6 +198,7 @@ long int spd_sdram() if(spd.mem_type == SPD_MEMTYPE_DDR2) { immap->sysconf.ddrcdr = CFG_DDRCDR_VALUE; } + udelay(50000); #endif /* @@ -576,7 +577,7 @@ long int spd_sdram() if (effective_data_rate == 266 || effective_data_rate == 333) { cpo = 0x7; /* READ_LAT + 5/4 */ } else if (effective_data_rate == 400) { - cpo = 0x9; /* READ_LAT + 7/4 */ + cpo = 0x7; /* READ_LAT + 5/4 */ } else { /* Automatic calibration */ cpo = 0x1f; @@ -705,9 +706,11 @@ long int spd_sdram() * SDRAM Cfg 2 */ odt_cfg = 0; +#ifndef CONFIG_NEVER_ASSERT_ODT_TO_CPU if (odt_rd_cfg | odt_wr_cfg) { odt_cfg = 0x2; /* ODT to IOs during reads */ } +#endif if (spd.mem_type == SPD_MEMTYPE_DDR2) { ddr->sdram_cfg2 = (0 | (0 << 26) /* True DQS */ diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c index ca6284b7265..108cebd8797 100644 --- a/drivers/net/tsec.c +++ b/drivers/net/tsec.c @@ -674,6 +674,15 @@ uint mii_cis8204_setmode(uint mii_reg, struct tsec_private * priv) return MIIM_CIS8204_EPHYCON_INIT; } +uint mii_m88e1111s_setmode(uint mii_reg, struct tsec_private *priv) +{ + uint mii_data = read_phy_reg(priv, mii_reg); + + if (priv->flags & TSEC_REDUCED) + mii_data = (mii_data & 0xfff0) | 0x000b; + return mii_data; +} + /* Initialized required registers to appropriate values, zeroing * those we don't care about (unless zero is bad, in which case, * choose a more appropriate value) @@ -1034,6 +1043,7 @@ struct phy_info phy_info_M88E1111S = { (struct phy_cmd[]){ /* config */ /* Reset and configure the PHY */ {MIIM_CONTROL, MIIM_CONTROL_RESET, NULL}, + {0x1b, 0x848f, &mii_m88e1111s_setmode}, {0x14, 0x0cd2, NULL}, /* Delay RGMII TX and RX */ {MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT, NULL}, {MIIM_ANAR, MIIM_ANAR_INIT, NULL}, diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h new file mode 100644 index 00000000000..7e344925ce3 --- /dev/null +++ b/include/configs/MPC837XEMDS.h @@ -0,0 +1,605 @@ +/* + * Copyright (C) 2007 Freescale Semiconductor, Inc. + * Dave Liu + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC837X 1 /* MPC837X CPU specific */ +#define CONFIG_MPC837XEMDS 1 /* MPC837XEMDS board specific */ + +/* + * System Clock Setup + */ +#ifdef CONFIG_PCISLAVE +#define CONFIG_83XX_PCICLK 66000000 /* in HZ */ +#else +#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ +#endif + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 66000000 +#endif + +/* + * Hardware Reset Configuration Word + * if CLKIN is 66MHz, then + * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_SVCOD_DIV_2 |\ + HRCWL_CSB_TO_CLKIN_6X1 |\ + HRCWL_CORE_TO_CSB_1_5X1) + +#ifdef CONFIG_PCISLAVE +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_AGENT |\ + HRCWH_PCI1_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0XFFF00100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LDP_CLEAR) +#else +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_RL_EXT_LEGACY |\ + HRCWH_TSEC1M_IN_RGMII |\ + HRCWH_TSEC2M_IN_RGMII |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LDP_CLEAR) +#endif + +/* + * eTSEC Clock Config + */ +#define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ +#define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ + +/* + * System IO Config + */ +#define CFG_SICRH 0x00000000 +#define CFG_SICRL 0x00000000 + +/* + * Output Buffer Impedance + */ +#define CFG_OBIR 0x31100000 + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CFG_83XX_DDR_USES_CS0 +#define CFG_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ + +#undef CONFIG_DDR_ECC /* support DDR ECC function */ +#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ + +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ + +#if defined(CONFIG_SPD_EEPROM) +#define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ +#else +/* + * Manually set up DDR parameters + * WHITE ELECTRONIC DESGGNS - W3HG64M72EEU403PD4 SO-DIMM + * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 + */ +#define CFG_DDR_SIZE 512 /* MB */ +#define CFG_DDR_CS0_BNDS 0x0000001f +#define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ + | 0x00010000 /* ODT_WR to CSn */ \ + | CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 ) + /* 0x80010202 */ +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ + | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ + | ( 6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ + | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ + | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) + /* 0x00620802 */ +#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ + | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ + | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ + | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ + | (13 << TIMING_CFG1_REFREC_SHIFT ) \ + | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ + | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ + | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) + /* 0x3935d322 */ +#define CFG_DDR_TIMING_2 ( ( 2 << TIMING_CFG2_ADD_LAT_SHIFT ) \ + | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ + | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ + | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ + | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ + | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) + /* 0x231088c8 */ +#define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ + | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) + /* 0x03E00100 */ +#define CFG_DDR_SDRAM_CFG 0x43000000 +#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ +#define CFG_DDR_MODE ( ( 0x0450 << SDRAM_MODE_ESD_SHIFT ) \ + | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) + /* ODT 150ohm CL=3, AL=2 on SDRAM */ +#define CFG_DDR_MODE2 0x00000000 +#endif + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00040000 /* memtest region */ +#define CFG_MEMTEST_END 0x00140000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) +#define CFG_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ + OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * BCSR on the Local Bus + */ +#define CFG_BCSR 0xF8000000 +#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ +#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ + +#define CFG_BR1_PRELIM (CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ +#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ + +/* + * NAND Flash on the Local Bus + */ +#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CFG_BR3_PRELIM ( CFG_NAND_BASE \ + | (2< " +#endif + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_HAS_BD_T 1 +#define CONFIG_OF_HAS_UBOOT_ENV 1 + +#define OF_CPU "PowerPC,837x@0" +#define OF_SOC "soc837x@e0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc837x@e0000000/serial@4500" + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI_MEM_BASE 0x80000000 +#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE +#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_MMIO_BASE 0x90000000 +#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE +#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI_IO_BASE 0xE0300000 +#define CFG_PCI_IO_PHYS 0xE0300000 +#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE +#define CFG_PCI_SLV_MEM_BUS 0x00000000 +#define CFG_PCI_SLV_MEM_SIZE 0x80000000 + +#ifdef CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ +#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#endif /* CONFIG_PCI */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* TSEC ethernet support */ +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 3 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC1" + +/* + * Environment + */ +#ifndef CFG_RAMBOOT + #define CFG_ENV_IS_IN_FLASH 1 + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + #define CFG_ENV_SIZE 0x2000 +#else + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_DATE + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CFG_RAMBOOT) + #undef CONFIG_CMD_ENV + #undef CONFIG_CMD_LOADS +#endif + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Cache Config + */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_SDRAM_LOWER CFG_SDRAM_BASE +#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) + +#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* BCSR: cache-inhibit and guarded */ +#define CFG_IBAT3L (CFG_BCSR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT3U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT4U CFG_IBAT4U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#else +#define CFG_IBAT6L (0) +#define CFG_IBAT6U (0) +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 00:E0:0C:00:83:79 +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:83:78 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=ramfs.83xx\0" \ + "fdtaddr=400000\0" \ + "fdtfile=mpc837xemds.dtb\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 921d4b19ad1be704df58725485d9292dc0414adf Mon Sep 17 00:00:00 2001 From: Kim Phillips Date: Mon, 19 Nov 2007 12:30:09 -0600 Subject: mpc83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions for 837x Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x. This change guarantees that the environment will be located on the first flash sector after the U-Boot image. Signed-off-by: Kim Phillips --- include/configs/MPC837XEMDS.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 7e344925ce3..524ff7c9283 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -197,6 +197,7 @@ #undef CFG_RAMBOOT #endif +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ @@ -386,7 +387,7 @@ */ #ifndef CFG_RAMBOOT #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) + #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #define CFG_ENV_SIZE 0x2000 #else -- cgit v1.3.1 From e6af9932d31171e35db880e7b2f29f903b1b7660 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Mon, 26 Nov 2007 11:00:54 -0600 Subject: Remove CONFIG options related to OF that we dont use The MPC8360E MDS config defined: CONFIG_OF_HAS_BD_T CONFIG_OF_HAS_UBOOT_ENV Which we don't use or ever needed. This seems like copy-paste feature creep. Signed-off-by: Kumar Gala --- include/configs/MPC8360EMDS.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 8098951c5b9..c192f33658d 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -349,8 +349,6 @@ #define CONFIG_OF_LIBFDT 1 #undef CONFIG_OF_FLAT_TREE #define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_HAS_BD_T 1 -#define CONFIG_OF_HAS_UBOOT_ENV 1 #define OF_CPU "PowerPC,8360@0" #define OF_SOC "soc8360@e0000000" -- cgit v1.3.1 From a1e1ac849249310e5e2e5c7148e9fb353a8317a7 Mon Sep 17 00:00:00 2001 From: Kim Phillips Date: Thu, 20 Dec 2007 01:30:48 -0600 Subject: mpc83xx: Remove CONFIG options related to OF that we dont use (on 837x) continuation of commit 37395fa2b0d9d617f28d44ca11592260ef16105a to 837x Signed-off-by: Kim Phillips --- include/configs/MPC837XEMDS.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'include') diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 524ff7c9283..772fd023817 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -297,8 +297,6 @@ /* Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_HAS_BD_T 1 -#define CONFIG_OF_HAS_UBOOT_ENV 1 #define OF_CPU "PowerPC,837x@0" #define OF_SOC "soc837x@e0000000" -- cgit v1.3.1 From e496865ecc31a2fe2f9abfe798334bb02aaf05ab Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Thu, 20 Dec 2007 12:58:51 -0500 Subject: sbc8349: enable libfdt by default on WRS SBC8349 board. Make libfdt the default for the WRS SBC8349 board. Parallel of commit 35cc4e4823668e8745854899cfaedd4489beb0ef done for the other 83xx based boards. Also fix a typo in CONFIG_PCI. Signed-off-by: Paul Gortmaker --- include/configs/sbc8349.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index e7d8a5a6627..45f20dc12ca 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -310,7 +310,7 @@ #endif /* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define OF_CPU "PowerPC,8349@0" @@ -458,7 +458,7 @@ #define CONFIG_CMD_PING #if defined(CONFIG_PCI) - #define CONFG_CMD_PCI + #define CONFIG_CMD_PCI #endif #if defined(CFG_RAMBOOT) -- cgit v1.3.1 From 5b8bc606c61456566af6912f818a153b6b06f242 Mon Sep 17 00:00:00 2001 From: Kim Phillips Date: Thu, 20 Dec 2007 14:09:22 -0600 Subject: mpc83xx: convert to using do_fixup_*() convert to using simpler mpc85xx style fdt update code; streamline by eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm the old school FLAT_TREE code from 83xx (since the sbc8349 was just converted over to using libfdt). Signed-off-by: Kim Phillips --- board/freescale/mpc832xemds/pci.c | 30 ++- board/freescale/mpc8349emds/pci.c | 51 ++-- board/freescale/mpc8349itx/pci.c | 51 ++-- board/freescale/mpc8360emds/mpc8360emds.c | 41 +-- board/freescale/mpc8360emds/pci.c | 27 +- board/sbc8349/pci.c | 43 ++- cpu/mpc83xx/Makefile | 2 +- cpu/mpc83xx/cpu.c | 426 ------------------------------ cpu/mpc83xx/fdt.c | 72 +++++ cpu/mpc83xx/pci.c | 83 +++--- include/configs/MPC8313ERDB.h | 6 +- include/configs/MPC8323ERDB.h | 7 +- include/configs/MPC832XEMDS.h | 7 +- include/configs/MPC8349EMDS.h | 6 +- include/configs/MPC8349ITX.h | 8 +- include/configs/MPC8360EMDS.h | 8 +- include/configs/MPC837XEMDS.h | 6 +- include/configs/sbc8349.h | 6 +- 18 files changed, 265 insertions(+), 615 deletions(-) create mode 100644 cpu/mpc83xx/fdt.c (limited to 'include') diff --git a/board/freescale/mpc832xemds/pci.c b/board/freescale/mpc832xemds/pci.c index 7818a2e1ee9..d50b78aa843 100644 --- a/board/freescale/mpc832xemds/pci.c +++ b/board/freescale/mpc832xemds/pci.c @@ -22,6 +22,7 @@ #include #elif defined(CONFIG_OF_LIBFDT) #include +#include #endif #include @@ -262,23 +263,28 @@ void pci_init_board(void) #endif /* CONFIG_PCISLAVE */ #if defined(CONFIG_OF_LIBFDT) -void -ft_pci_setup(void *blob, bd_t *bd) +void ft_pci_setup(void *blob, bd_t *bd) { int nodeoffset; - int err; int tmp[2]; + const char *path; + + if (pci_num_buses < 1) + return; - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); + nodeoffset = fdt_path_offset(blob, "/aliases"); if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(hose[0].first_busno); - tmp[1] = cpu_to_be32(hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } } } #elif defined(CONFIG_OF_FLAT_TREE) diff --git a/board/freescale/mpc8349emds/pci.c b/board/freescale/mpc8349emds/pci.c index 7bcdccbcc67..3eaf77a5910 100644 --- a/board/freescale/mpc8349emds/pci.c +++ b/board/freescale/mpc8349emds/pci.c @@ -29,6 +29,7 @@ #include #elif defined(CONFIG_OF_LIBFDT) #include +#include #endif @@ -389,37 +390,39 @@ pci_init_board(void) } #if defined(CONFIG_OF_LIBFDT) -void -ft_pci_setup(void *blob, bd_t *bd) +void ft_pci_setup(void *blob, bd_t *bd) { int nodeoffset; - int err; int tmp[2]; + const char *path; - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); + nodeoffset = fdt_path_offset(blob, "/aliases"); if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[0].first_busno); - tmp[1] = cpu_to_be32(pci_hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } #ifdef CONFIG_MPC83XX_PCI2 - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8600"); - if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[1].first_busno); - tmp[1] = cpu_to_be32(pci_hose[1].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } + path = fdt_getprop(blob, nodeoffset, "pci1", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } #endif + } } #elif defined(CONFIG_OF_FLAT_TREE) void diff --git a/board/freescale/mpc8349itx/pci.c b/board/freescale/mpc8349itx/pci.c index a764a61867a..a6bb101b4d1 100644 --- a/board/freescale/mpc8349itx/pci.c +++ b/board/freescale/mpc8349itx/pci.c @@ -33,6 +33,7 @@ #include #elif defined(CONFIG_OF_LIBFDT) #include +#include #endif DECLARE_GLOBAL_DATA_PTR; @@ -335,37 +336,39 @@ void pci_init_board(void) } #if defined(CONFIG_OF_LIBFDT) -void -ft_pci_setup(void *blob, bd_t *bd) +void ft_pci_setup(void *blob, bd_t *bd) { int nodeoffset; - int err; int tmp[2]; + const char *path; - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); + nodeoffset = fdt_path_offset(blob, "/aliases"); if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[0].first_busno); - tmp[1] = cpu_to_be32(pci_hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } #ifdef CONFIG_MPC83XX_PCI2 - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); - if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[1].first_busno); - tmp[1] = cpu_to_be32(pci_hose[1].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } + path = fdt_getprop(blob, nodeoffset, "pci1", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } #endif + } } #elif defined(CONFIG_OF_FLAT_TREE) void diff --git a/board/freescale/mpc8360emds/mpc8360emds.c b/board/freescale/mpc8360emds/mpc8360emds.c index e673840cfa4..a899800a8b7 100644 --- a/board/freescale/mpc8360emds/mpc8360emds.c +++ b/board/freescale/mpc8360emds/mpc8360emds.c @@ -327,25 +327,32 @@ void ft_board_setup(void *blob, bd_t *bd) immr->sysconf.spridr == SPR_8360E_REV21) { int nodeoffset; const char *prop; + const char *path; - /* fixup UCC 1 if using rgmii-id mode */ - nodeoffset = fdt_path_offset(blob, "/" OF_QE "/ucc@2000"); + nodeoffset = fdt_path_offset(fdt, "/aliases"); if (nodeoffset >= 0) { - prop = fdt_getprop(blob, nodeoffset, - "phy-connection-type", 0); - if (prop && (strcmp(prop, "rgmii-id") == 0)) - fdt_setprop(blob, nodeoffset, "phy-connection-type", - "rgmii-rxid", sizeof("rgmii-rxid")); - } - - /* fixup UCC 2 if using rgmii-id mode */ - nodeoffset = fdt_path_offset(blob, "/" OF_QE "/ucc@3000"); - if (nodeoffset >= 0) { - prop = fdt_getprop(blob, nodeoffset, - "phy-connection-type", 0); - if (prop && (strcmp(prop, "rgmii-id") == 0)) - fdt_setprop(blob, nodeoffset, "phy-connection-type", - "rgmii-rxid", sizeof("rgmii-rxid")); +#if defined(CONFIG_HAS_ETH0) + /* fixup UCC 1 if using rgmii-id mode */ + path = fdt_getprop(blob, nodeoffset, "ethernet0", NULL); + if (path) { + prop = fdt_getprop(blob, nodeoffset, + "phy-connection-type", 0); + if (prop && (strcmp(prop, "rgmii-id") == 0)) + fdt_setprop(blob, nodeoffset, "phy-connection-type", + "rgmii-rxid", sizeof("rgmii-rxid")); + } +#endif +#if defined(CONFIG_HAS_ETH1) + /* fixup UCC 2 if using rgmii-id mode */ + path = fdt_getprop(blob, nodeoffset, "ethernet1", NULL); + if (path) { + prop = fdt_getprop(blob, nodeoffset, + "phy-connection-type", 0); + if (prop && (strcmp(prop, "rgmii-id") == 0)) + fdt_setprop(blob, nodeoffset, "phy-connection-type", + "rgmii-rxid", sizeof("rgmii-rxid")); + } +#endif } } } diff --git a/board/freescale/mpc8360emds/pci.c b/board/freescale/mpc8360emds/pci.c index f18e532ef5f..64cb8ade62f 100644 --- a/board/freescale/mpc8360emds/pci.c +++ b/board/freescale/mpc8360emds/pci.c @@ -22,6 +22,7 @@ #include #elif defined(CONFIG_OF_LIBFDT) #include +#include #endif #include @@ -262,23 +263,25 @@ void pci_init_board(void) #endif /* CONFIG_PCISLAVE */ #if defined(CONFIG_OF_LIBFDT) -void -ft_pci_setup(void *blob, bd_t *bd) +void ft_pci_setup(void *blob, bd_t *bd) { int nodeoffset; - int err; int tmp[2]; + const char *path; - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); + nodeoffset = fdt_path_offset(blob, "/aliases"); if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(hose[0].first_busno); - tmp[1] = cpu_to_be32(hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } } } #elif defined(CONFIG_OF_FLAT_TREE) diff --git a/board/sbc8349/pci.c b/board/sbc8349/pci.c index eadf230983d..e59f9f9a59a 100644 --- a/board/sbc8349/pci.c +++ b/board/sbc8349/pci.c @@ -30,6 +30,12 @@ #include #include #include +#if defined(CONFIG_OF_FLAT_TREE) +#include +#elif defined(CONFIG_OF_LIBFDT) +#include +#include +#endif DECLARE_GLOBAL_DATA_PTR; @@ -323,7 +329,42 @@ pci_init_board(void) } -#ifdef CONFIG_OF_FLAT_TREE +#if defined(CONFIG_OF_LIBFDT) +void ft_pci_setup(void *blob, bd_t *bd) +{ + int nodeoffset; + int tmp[2]; + const char *path; + + nodeoffset = fdt_path_offset(blob, "/aliases"); + if (nodeoffset >= 0) { + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } +#ifdef CONFIG_MPC83XX_PCI2 + path = fdt_getprop(blob, nodeoffset, "pci1", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } +#endif + } +} +#elif defined(CONFIG_OF_FLAT_TREE) void ft_pci_setup(void *blob, bd_t *bd) { diff --git a/cpu/mpc83xx/Makefile b/cpu/mpc83xx/Makefile index 23299700510..94a3cb83347 100644 --- a/cpu/mpc83xx/Makefile +++ b/cpu/mpc83xx/Makefile @@ -29,7 +29,7 @@ LIB = $(obj)lib$(CPU).a START = start.o COBJS = traps.o cpu.o cpu_init.o speed.o interrupts.o \ - spd_sdram.o ecc.o qe_io.o pci.o + spd_sdram.o ecc.o qe_io.o pci.o fdt.o SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/cpu/mpc83xx/cpu.c b/cpu/mpc83xx/cpu.c index 3d3f20a636d..bff3cefda94 100644 --- a/cpu/mpc83xx/cpu.c +++ b/cpu/mpc83xx/cpu.c @@ -31,12 +31,7 @@ #include #include #include -#if defined(CONFIG_OF_FLAT_TREE) -#include -#elif defined(CONFIG_OF_LIBFDT) #include -#include -#endif DECLARE_GLOBAL_DATA_PTR; @@ -359,427 +354,6 @@ void watchdog_reset (void) } #endif -#if defined(CONFIG_OF_LIBFDT) - -/* - * "Setter" functions used to add/modify FDT entries. - */ -static int fdt_set_eth0(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - /* Fix it up if it exists, don't create it if it doesn't exist */ - if (fdt_get_property(blob, nodeoffset, name, 0)) { - return fdt_setprop(blob, nodeoffset, name, bd->bi_enetaddr, 6); - } - return 0; -} -#ifdef CONFIG_HAS_ETH1 -/* second onboard ethernet port */ -static int fdt_set_eth1(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - /* Fix it up if it exists, don't create it if it doesn't exist */ - if (fdt_get_property(blob, nodeoffset, name, 0)) { - return fdt_setprop(blob, nodeoffset, name, bd->bi_enet1addr, 6); - } - return 0; -} -#endif -#ifdef CONFIG_HAS_ETH2 -/* third onboard ethernet port */ -static int fdt_set_eth2(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - /* Fix it up if it exists, don't create it if it doesn't exist */ - if (fdt_get_property(blob, nodeoffset, name, 0)) { - return fdt_setprop(blob, nodeoffset, name, bd->bi_enet2addr, 6); - } - return 0; -} -#endif -#ifdef CONFIG_HAS_ETH3 -/* fourth onboard ethernet port */ -static int fdt_set_eth3(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - /* Fix it up if it exists, don't create it if it doesn't exist */ - if (fdt_get_property(blob, nodeoffset, name, 0)) { - return fdt_setprop(blob, nodeoffset, name, bd->bi_enet3addr, 6); - } - return 0; -} -#endif - -static int fdt_set_busfreq(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - u32 tmp; - /* Create or update the property */ - tmp = cpu_to_be32(bd->bi_busfreq); - return fdt_setprop(blob, nodeoffset, name, &tmp, sizeof(tmp)); -} - -static int fdt_set_tbfreq(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - u32 tmp; - /* Create or update the property */ - tmp = cpu_to_be32(OF_TBCLK); - return fdt_setprop(blob, nodeoffset, name, &tmp, sizeof(tmp)); -} - - -static int fdt_set_clockfreq(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - u32 tmp; - /* Create or update the property */ - tmp = cpu_to_be32(gd->core_clk); - return fdt_setprop(blob, nodeoffset, name, &tmp, sizeof(tmp)); -} - -#ifdef CONFIG_QE -static int fdt_set_qe_busfreq(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - u32 tmp; - /* Create or update the property */ - tmp = cpu_to_be32(gd->qe_clk); - return fdt_setprop(blob, nodeoffset, name, &tmp, sizeof(tmp)); -} - -static int fdt_set_qe_brgfreq(void *blob, int nodeoffset, const char *name, bd_t *bd) -{ - u32 tmp; - /* Create or update the property */ - tmp = cpu_to_be32(gd->brg_clk); - return fdt_setprop(blob, nodeoffset, name, &tmp, sizeof(tmp)); -} -#endif - -/* - * Fixups to the fdt. - */ -static const struct { - char *node; - char *prop; - int (*set_fn)(void *blob, int nodeoffset, const char *name, bd_t *bd); -} fixup_props[] = { - { "/cpus/" OF_CPU, - "timebase-frequency", - fdt_set_tbfreq - }, - { "/cpus/" OF_CPU, - "bus-frequency", - fdt_set_busfreq - }, - { "/cpus/" OF_CPU, - "clock-frequency", - fdt_set_clockfreq - }, - { "/" OF_SOC, - "bus-frequency", - fdt_set_busfreq - }, - { "/" OF_SOC "/serial@4500", - "clock-frequency", - fdt_set_busfreq - }, - { "/" OF_SOC "/serial@4600", - "clock-frequency", - fdt_set_busfreq - }, -#ifdef CONFIG_TSEC1 - { "/" OF_SOC "/ethernet@24000", - "mac-address", - fdt_set_eth0 - }, - { "/" OF_SOC "/ethernet@24000", - "local-mac-address", - fdt_set_eth0 - }, -#endif -#ifdef CONFIG_TSEC2 - { "/" OF_SOC "/ethernet@25000", - "mac-address", - fdt_set_eth1 - }, - { "/" OF_SOC "/ethernet@25000", - "local-mac-address", - fdt_set_eth1 - }, -#endif -#ifdef CONFIG_QE - { "/" OF_QE, - "brg-frequency", - fdt_set_qe_brgfreq - }, - { "/" OF_QE, - "bus-frequency", - fdt_set_qe_busfreq - }, -#ifdef CONFIG_UEC_ETH1 -#if CFG_UEC1_UCC_NUM == 0 /* UCC1 */ - { "/" OF_QE "/ucc@2000", - "mac-address", - fdt_set_eth0 - }, - { "/" OF_QE "/ucc@2000", - "local-mac-address", - fdt_set_eth0 - }, -#elif CFG_UEC1_UCC_NUM == 1 /* UCC2 */ - { "/" OF_QE "/ucc@3000", - "mac-address", - fdt_set_eth0 - }, - { "/" OF_QE "/ucc@3000", - "local-mac-address", - fdt_set_eth0 - }, -#elif CFG_UEC1_UCC_NUM == 2 /* UCC3 */ - { "/" OF_QE "/ucc@2200", - "mac-address", - fdt_set_eth0 - }, - { "/" OF_QE "/ucc@2200", - "local-mac-address", - fdt_set_eth0 - }, -#elif CFG_UEC1_UCC_NUM == 3 /* UCC4 */ - { "/" OF_QE "/ucc@3200", - "mac-address", - fdt_set_eth0 - }, - { "/" OF_QE "/ucc@3200", - "local-mac-address", - fdt_set_eth0 - }, -#endif -#endif /* CONFIG_UEC_ETH1 */ -#ifdef CONFIG_UEC_ETH2 -#if CFG_UEC2_UCC_NUM == 0 /* UCC1 */ - { "/" OF_QE "/ucc@2000", - "mac-address", - fdt_set_eth1 - }, - { "/" OF_QE "/ucc@2000", - "local-mac-address", - fdt_set_eth1 - }, -#elif CFG_UEC2_UCC_NUM == 1 /* UCC2 */ - { "/" OF_QE "/ucc@3000", - "mac-address", - fdt_set_eth1 - }, - { "/" OF_QE "/ucc@3000", - "local-mac-address", - fdt_set_eth1 - }, -#elif CFG_UEC2_UCC_NUM == 2 /* UCC3 */ - { "/" OF_QE "/ucc@2200", - "mac-address", - fdt_set_eth1 - }, - { "/" OF_QE "/ucc@2200", - "local-mac-address", - fdt_set_eth1 - }, -#elif CFG_UEC2_UCC_NUM == 3 /* UCC4 */ - { "/" OF_QE "/ucc@3200", - "mac-address", - fdt_set_eth1 - }, - { "/" OF_QE "/ucc@3200", - "local-mac-address", - fdt_set_eth1 - }, -#endif -#endif /* CONFIG_UEC_ETH2 */ -#ifdef CONFIG_UEC_ETH3 -#if CFG_UEC3_UCC_NUM == 0 /* UCC1 */ - { "/" OF_QE "/ucc@2000", - "mac-address", - fdt_set_eth2 - }, - { "/" OF_QE "/ucc@2000", - "local-mac-address", - fdt_set_eth2 - }, -#elif CFG_UEC3_UCC_NUM == 1 /* UCC2 */ - { "/" OF_QE "/ucc@3000", - "mac-address", - fdt_set_eth2 - }, - { "/" OF_QE "/ucc@3000", - "local-mac-address", - fdt_set_eth2 - }, -#elif CFG_UEC3_UCC_NUM == 2 /* UCC3 */ - { "/" OF_QE "/ucc@2200", - "mac-address", - fdt_set_eth2 - }, - { "/" OF_QE "/ucc@2200", - "local-mac-address", - fdt_set_eth2 - }, -#elif CFG_UEC3_UCC_NUM == 3 /* UCC4 */ - { "/" OF_QE "/ucc@3200", - "mac-address", - fdt_set_eth2 - }, - { "/" OF_QE "/ucc@3200", - "local-mac-address", - fdt_set_eth2 - }, -#endif -#endif /* CONFIG_UEC_ETH3 */ -#ifdef CONFIG_UEC_ETH4 -#if CFG_UEC4_UCC_NUM == 0 /* UCC1 */ - { "/" OF_QE "/ucc@2000", - "mac-address", - fdt_set_eth3 - }, - { "/" OF_QE "/ucc@2000", - "local-mac-address", - fdt_set_eth3 - }, -#elif CFG_UEC4_UCC_NUM == 1 /* UCC2 */ - { "/" OF_QE "/ucc@3000", - "mac-address", - fdt_set_eth3 - }, - { "/" OF_QE "/ucc@3000", - "local-mac-address", - fdt_set_eth3 - }, -#elif CFG_UEC4_UCC_NUM == 2 /* UCC3 */ - { "/" OF_QE "/ucc@2200", - "mac-address", - fdt_set_eth3 - }, - { "/" OF_QE "/ucc@2200", - "local-mac-address", - fdt_set_eth3 - }, -#elif CFG_UEC4_UCC_NUM == 3 /* UCC4 */ - { "/" OF_QE "/ucc@3200", - "mac-address", - fdt_set_eth3 - }, - { "/" OF_QE "/ucc@3200", - "local-mac-address", - fdt_set_eth3 - }, -#endif -#endif /* CONFIG_UEC_ETH4 */ -#endif /* CONFIG_QE */ -}; - -void -ft_cpu_setup(void *blob, bd_t *bd) -{ - int nodeoffset; - int err; - int j; - - for (j = 0; j < (sizeof(fixup_props) / sizeof(fixup_props[0])); j++) { - nodeoffset = fdt_path_offset(blob, fixup_props[j].node); - if (nodeoffset >= 0) { - err = fixup_props[j].set_fn(blob, nodeoffset, - fixup_props[j].prop, bd); - if (err < 0) - debug("Problem setting %s = %s: %s\n", - fixup_props[j].node, fixup_props[j].prop, - fdt_strerror(err)); - } else { - debug("Couldn't find %s: %s\n", - fixup_props[j].node, fdt_strerror(nodeoffset)); - } - } - - fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); -} -#elif defined(CONFIG_OF_FLAT_TREE) -void -ft_cpu_setup(void *blob, bd_t *bd) -{ - u32 *p; - int len; - ulong clock; - - clock = bd->bi_busfreq; - p = ft_get_prop(blob, "/cpus/" OF_CPU "/bus-frequency", &len); - if (p != NULL) - *p = cpu_to_be32(clock); - - p = ft_get_prop(blob, "/" OF_SOC "/bus-frequency", &len); - if (p != NULL) - *p = cpu_to_be32(clock); - - p = ft_get_prop(blob, "/" OF_SOC "/serial@4500/clock-frequency", &len); - if (p != NULL) - *p = cpu_to_be32(clock); - - p = ft_get_prop(blob, "/" OF_SOC "/serial@4600/clock-frequency", &len); - if (p != NULL) - *p = cpu_to_be32(clock); - -#ifdef CONFIG_TSEC1 - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); - - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@24000/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); -#endif - -#ifdef CONFIG_TSEC2 - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); - - p = ft_get_prop(blob, "/" OF_SOC "/ethernet@25000/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); -#endif - -#ifdef CONFIG_UEC_ETH1 -#if CFG_UEC1_UCC_NUM == 0 /* UCC1 */ - p = ft_get_prop(blob, "/" OF_QE "/ucc@2000/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); - - p = ft_get_prop(blob, "/" OF_QE "/ucc@2000/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); -#elif CFG_UEC1_UCC_NUM == 2 /* UCC3 */ - p = ft_get_prop(blob, "/" OF_QE "/ucc@2200/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); - - p = ft_get_prop(blob, "/" OF_QE "/ucc@2200/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enetaddr, 6); -#endif -#endif - -#ifdef CONFIG_UEC_ETH2 -#if CFG_UEC2_UCC_NUM == 1 /* UCC2 */ - p = ft_get_prop(blob, "/" OF_QE "/ucc@3000/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); - - p = ft_get_prop(blob, "/" OF_QE "/ucc@3000/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); -#elif CFG_UEC2_UCC_NUM == 3 /* UCC4 */ - p = ft_get_prop(blob, "/" OF_QE "/ucc@3200/mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); - - p = ft_get_prop(blob, "/" OF_QE "/ucc@3200/local-mac-address", &len); - if (p != NULL) - memcpy(p, bd->bi_enet1addr, 6); -#endif -#endif -} -#endif - #if defined(CONFIG_DDR_ECC) void dma_init(void) { diff --git a/cpu/mpc83xx/fdt.c b/cpu/mpc83xx/fdt.c new file mode 100644 index 00000000000..f21c54e80bc --- /dev/null +++ b/cpu/mpc83xx/fdt.c @@ -0,0 +1,72 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +#if defined(CONFIG_OF_LIBFDT) + +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +void ft_cpu_setup(void *blob, bd_t *bd) +{ +#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) ||\ + defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) + fdt_fixup_ethernet(blob, bd); +#endif + + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "timebase-frequency", (bd->bi_busfreq / 4), 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "clock-frequency", gd->core_clk, 1); + do_fixup_by_prop_u32(blob, "device_type", "soc", 4, + "bus-frequency", bd->bi_busfreq, 1); +#ifdef CONFIG_QE + do_fixup_by_prop_u32(blob, "device_type", "qe", 4, + "bus-frequency", gd->qe_clk, 1); + do_fixup_by_prop_u32(blob, "device_type", "qe", 4, + "brg-frequency", gd->brg_clk, 1); +#endif + +#ifdef CFG_NS16550 + do_fixup_by_compat_u32(blob, "ns16550", + "clock-frequency", bd->bi_busfreq, 1); +#endif + +#ifdef CONFIG_CPM2 + do_fixup_by_compat_u32(blob, "fsl,cpm2-scc-uart", + "current-speed", bd->bi_baudrate, 1); + + do_fixup_by_compat_u32(blob, "fsl,cpm2-brg", + "clock-frequency", bd->bi_brgfreq, 1); +#endif + + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); +} +#endif /* CONFIG_OF_LIBFDT */ diff --git a/cpu/mpc83xx/pci.c b/cpu/mpc83xx/pci.c index 0defb0ec890..18558db537b 100644 --- a/cpu/mpc83xx/pci.c +++ b/cpu/mpc83xx/pci.c @@ -28,8 +28,7 @@ #if defined(CONFIG_OF_LIBFDT) #include -#elif defined(CONFIG_OF_FLAT_TREE) -#include +#include #endif #include @@ -173,63 +172,41 @@ void mpc83xx_pci_init(int num_buses, struct pci_region **reg, int warmboot) void ft_pci_setup(void *blob, bd_t *bd) { int nodeoffset; - int err; int tmp[2]; + const char *path; if (pci_num_buses < 1) return; - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8500"); + nodeoffset = fdt_path_offset(blob, "/aliases"); if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[0].first_busno); - tmp[1] = cpu_to_be32(pci_hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } - - if (pci_num_buses < 2) - return; - - nodeoffset = fdt_path_offset(blob, "/" OF_SOC "/pci@8600"); - if (nodeoffset >= 0) { - tmp[0] = cpu_to_be32(pci_hose[0].first_busno); - tmp[1] = cpu_to_be32(pci_hose[0].last_busno); - err = fdt_setprop(blob, nodeoffset, "bus-range", - tmp, sizeof(tmp)); - - tmp[0] = cpu_to_be32(gd->pci_clk); - err = fdt_setprop(blob, nodeoffset, "clock-frequency", - tmp, sizeof(tmp[0])); - } -} -#elif CONFIG_OF_FLAT_TREE -void ft_pci_setup(void *blob, bd_t *bd) -{ - u32 *p; - int len; - - if (pci_num_buses < 1) - return; - - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8500/bus-range", &len); - if (p) { - p[0] = pci_hose[0].first_busno; - p[1] = pci_hose[0].last_busno; - } - - if (pci_num_buses < 2) - return; - - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8600/bus-range", &len); - if (p) { - p[0] = pci_hose[1].first_busno; - p[1] = pci_hose[1].last_busno; + path = fdt_getprop(blob, nodeoffset, "pci0", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } + + if (pci_num_buses < 2) + return; + + path = fdt_getprop(blob, nodeoffset, "pci1", NULL); + if (path) { + tmp[0] = cpu_to_be32(pci_hose[0].first_busno); + tmp[1] = cpu_to_be32(pci_hose[0].last_busno); + do_fixup_by_path(blob, path, "bus-range", + &tmp, sizeof(tmp), 1); + + tmp[0] = cpu_to_be32(gd->pci_clk); + do_fixup_by_path(blob, path, "clock-frequency", + &tmp, sizeof(tmp[0]), 1); + } } } -#endif /* CONFIG_OF_FLAT_TREE */ - +#endif /* CONFIG_OF_LIBFDT */ #endif /* CONFIG_83XX_GENERIC_PCI */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 0c3bc16c9cb..c9a9c83f220 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -231,11 +231,7 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8313@0" -#define OF_SOC "soc8313@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8313@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* * Serial Port diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 558f94bb77a..564de02f5b5 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -270,12 +270,7 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8323@0" -#define OF_SOC "soc8323@e0000000" -#define OF_QE "qe@e0100000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8323@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 5345fc62f80..a48b3117b60 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -321,12 +321,7 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8323@0" -#define OF_SOC "soc8323@e0000000" -#define OF_QE "qe@e0100000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8323@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 7d5b17b50b1..03409bbbafa 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -341,11 +341,7 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8349@0" -#define OF_SOC "soc8349@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 2a2e753c87d..49dc0de535e 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -298,12 +298,8 @@ boards, we say we have two, but don't display a message if we find only one. */ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP - -#define OF_CPU "PowerPC,8349@0" -#define OF_SOC "soc8349@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500" +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* * PCI diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index c192f33658d..fedb8a9c5bf 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -347,14 +347,8 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 -#undef CONFIG_OF_FLAT_TREE #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8360@0" -#define OF_SOC "soc8360@e0000000" -#define OF_QE "qe@e0100000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8360@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 772fd023817..0958e6b9679 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -297,11 +297,7 @@ /* Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,837x@0" -#define OF_SOC "soc837x@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc837x@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 45f20dc12ca..9efe3c49de7 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -312,11 +312,7 @@ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,8349@0" -#define OF_SOC "soc8349@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500" +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ -- cgit v1.3.1 From 22fb2246df91bfc840d87f0c5910818bad55577a Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 28 Dec 2007 11:56:30 +0100 Subject: Add fdt_find_and_setprop() to fdt_support.h fdt_find_and_setprop() is used by several 4xx boards and it's missing in the appropriate header. This patch eliminates a warning when building U-Boot for such boards. Signed-off-by: Matthias Fuchs Acked-by: Stefan Roese --- include/fdt_support.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/fdt_support.h b/include/fdt_support.h index 3d6c1a841b7..58e26abf827 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -46,6 +46,8 @@ void do_fixup_by_compat_u32(void *fdt, const char *compat, const char *prop, u32 val, int create); int fdt_fixup_memory(void *blob, u64 start, u64 size); void fdt_fixup_ethernet(void *fdt, bd_t *bd); +int fdt_find_and_setprop(void *fdt, const char *node, const char *prop, + const void *val, int len, int create); #ifdef CONFIG_OF_HAS_UBOOT_ENV int fdt_env(void *fdt); -- cgit v1.3.1 From 9d4450b5adc36623e9c1de1f92539db77ad0c57e Mon Sep 17 00:00:00 2001 From: David Gibson Date: Mon, 17 Dec 2007 14:41:52 +1100 Subject: libfdt: Add more documentation (patch the sixth) This patch adds some more documenting comments to libfdt.h. Specifically this documents all the write-in-place functions. Signed-off-by: David Gibson --- include/libfdt.h | 104 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 104 insertions(+) (limited to 'include') diff --git a/include/libfdt.h b/include/libfdt.h index 805004900da..ffac678d9e9 100644 --- a/include/libfdt.h +++ b/include/libfdt.h @@ -655,8 +655,65 @@ int fdt_node_offset_by_compatible(const void *fdt, int startoffset, /* Write-in-place functions */ /**********************************************************************/ +/** + * fdt_setprop_inplace - change a property's value, but not its size + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: pointer to data to replace the property value with + * @len: length of the property value + * + * fdt_setprop_inplace() replaces the value of a given property with + * the data in val, of length len. This function cannot change the + * size of a property, and so will only work if len is equal to the + * current length of the property. + * + * This function will alter only the bytes in the blob which contain + * the given property value, and will not alter or move any other part + * of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, if len is not equal to the property's current length + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_setprop_inplace(void *fdt, int nodeoffset, const char *name, const void *val, int len); + +/** + * fdt_setprop_inplace_cell - change the value of a single-cell property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: cell (32-bit integer) value to replace the property with + * + * fdt_setprop_inplace_cell() replaces the value of a given property + * with the 32-bit integer cell value in val, converting val to + * big-endian if necessary. This function cannot change the size of a + * property, and so will only work if the property already exists and + * has length 4. + * + * This function will alter only the bytes in the blob which contain + * the given property value, and will not alter or move any other part + * of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, if the property's length is not equal to 4 + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ static inline int fdt_setprop_inplace_cell(void *fdt, int nodeoffset, const char *name, uint32_t val) { @@ -664,7 +721,54 @@ static inline int fdt_setprop_inplace_cell(void *fdt, int nodeoffset, return fdt_setprop_inplace(fdt, nodeoffset, name, &val, sizeof(val)); } +/** + * fdt_nop_property - replace a property with nop tags + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to nop + * @name: name of the property to nop + * + * fdt_nop_property() will replace a given property's representation + * in the blob with FDT_NOP tags, effectively removing it from the + * tree. + * + * This function will alter only the bytes in the blob which contain + * the property, and will not alter or move any other part of the + * tree. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_nop_property(void *fdt, int nodeoffset, const char *name); + +/** + * fdt_nop_node - replace a node (subtree) with nop tags + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node to nop + * + * fdt_nop_node() will replace a given node's representation in the + * blob, including all its subnodes, if any, with FDT_NOP tags, + * effectively removing it from the tree. + * + * This function will alter only the bytes in the blob which contain + * the node and its properties and subnodes, and will not alter or + * move any other part of the tree. + * + * returns: + * 0, on success + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_nop_node(void *fdt, int nodeoffset); /**********************************************************************/ -- cgit v1.3.1 From aec7135bc300e3340d18f203347ee00c5b5f68c0 Mon Sep 17 00:00:00 2001 From: David Gibson Date: Mon, 17 Dec 2007 14:42:07 +1100 Subject: libfdt: Add more documentation (patch the seventh) This patch adds more documenting comments to libfdt.h. Specifically, these document the read/write functions (not including fdt_open_into() and fdt_pack(), for now). Signed-off-by: David Gibson --- include/libfdt.h | 219 +++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 219 insertions(+) (limited to 'include') diff --git a/include/libfdt.h b/include/libfdt.h index ffac678d9e9..6c052368581 100644 --- a/include/libfdt.h +++ b/include/libfdt.h @@ -797,23 +797,242 @@ int fdt_finish(void *fdt); int fdt_open_into(const void *fdt, void *buf, int bufsize); int fdt_pack(void *fdt); +/** + * fdt_add_mem_rsv - add one memory reserve map entry + * @fdt: pointer to the device tree blob + * @addres, @size: 64-bit values (native endian) + * + * Adds a reserve map entry to the given blob reserving a region at + * address address of length size. + * + * This function will insert data into the reserve map and will + * therfore change the indexes of some entries in the table. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new reservation entry + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_add_mem_rsv(void *fdt, uint64_t address, uint64_t size); + +/** + * fdt_del_mem_rsv - remove a memory reserve map entry + * @fdt: pointer to the device tree blob + * @n: entry to remove + * + * fdt_del_mem_rsv() removes the n-th memory reserve map entry from + * the blob. + * + * This function will delete data from the reservation table and will + * therfore change the indexes of some entries in the table. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, there is no entry of the given index (i.e. there + * are less than n+1 reserve map entries) + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_del_mem_rsv(void *fdt, int n); +/** + * fdt_setprop - create or change a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: pointer to data to set the property value to + * @len: length of the property value + * + * fdt_setprop() sets the value of the named property in the given + * node to the given value and length, creeating the property if it + * does not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_setprop(void *fdt, int nodeoffset, const char *name, const void *val, int len); + +/** + * fdt_setprop_cell - set a property to a single cell value + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @val: 32-bit integer value for the property (native endian) + * + * fdt_setprop_cell() sets the value of the named property in the + * given node to the given cell value (converting to big-endian if + * necessary), or creates a new property with that value if it does + * not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ static inline int fdt_setprop_cell(void *fdt, int nodeoffset, const char *name, uint32_t val) { val = cpu_to_fdt32(val); return fdt_setprop(fdt, nodeoffset, name, &val, sizeof(val)); } + +/** + * fdt_setprop_string - set a property to a string value + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to change + * @name: name of the property to change + * @str: string value for the property + * + * fdt_setprop_string() sets the value of the named property in the + * given node to the given string value (using the length of the + * string to determine the new length of the property), or creates a + * new property with that value if it does not already exist. + * + * This function may insert or delete data from the blob, and will + * therefore change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOSPACE, there is insufficient free space in the blob to + * contain the new property value + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_TRUNCATED, standard meanings + */ #define fdt_setprop_string(fdt, nodeoffset, name, str) \ fdt_setprop((fdt), (nodeoffset), (name), (str), strlen(str)+1) + +/** + * fdt_delprop - delete a property + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node whose property to nop + * @name: name of the property to nop + * + * fdt_del_property() will delete the given property. + * + * This function will delete data from the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_NOTFOUND, node does not have the named property + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_delprop(void *fdt, int nodeoffset, const char *name); + +/** + * fdt_add_subnode_namelen - creates a new node based on substring + * @fdt: pointer to the device tree blob + * @parentoffset: structure block offset of a node + * @name: name of the subnode to locate + * @namelen: number of characters of name to consider + * + * Identical to fdt_add_subnode(), but use only the first namelen + * characters of name as the name of the new node. This is useful for + * creating subnodes based on a portion of a larger string, such as a + * full path. + */ int fdt_add_subnode_namelen(void *fdt, int parentoffset, const char *name, int namelen); + +/** + * fdt_add_subnode - creates a new node + * @fdt: pointer to the device tree blob + * @parentoffset: structure block offset of a node + * @name: name of the subnode to locate + * + * fdt_add_subnode() creates a new node as a subnode of the node at + * structure block offset parentoffset, with the given name (which + * should include the unit address, if any). + * + * This function will insert data into the blob, and will therefore + * change the offsets of some existing nodes. + + * returns: + * structure block offset of the created nodeequested subnode (>=0), on success + * -FDT_ERR_NOTFOUND, if the requested subnode does not exist + * -FDT_ERR_BADOFFSET, if parentoffset did not point to an FDT_BEGIN_NODE tag + * -FDT_ERR_EXISTS, if the node at parentoffset already has a subnode of + * the given name + * -FDT_ERR_NOSPACE, if there is insufficient free space in the + * blob to contain the new node + * -FDT_ERR_NOSPACE + * -FDT_ERR_BADLAYOUT + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings. + */ int fdt_add_subnode(void *fdt, int parentoffset, const char *name); + +/** + * fdt_del_node - delete a node (subtree) + * @fdt: pointer to the device tree blob + * @nodeoffset: offset of the node to nop + * + * fdt_del_node() will remove the given node, including all its + * subnodes if any, from the blob. + * + * This function will delete data from the blob, and will therefore + * change the offsets of some existing nodes. + * + * returns: + * 0, on success + * -FDT_ERR_BADOFFSET, nodeoffset did not point to FDT_BEGIN_NODE tag + * -FDT_ERR_BADLAYOUT, + * -FDT_ERR_BADMAGIC, + * -FDT_ERR_BADVERSION, + * -FDT_ERR_BADSTATE, + * -FDT_ERR_BADSTRUCTURE, + * -FDT_ERR_TRUNCATED, standard meanings + */ int fdt_del_node(void *fdt, int nodeoffset); /**********************************************************************/ -- cgit v1.3.1 From 7d5d75633174867316a0c0f2fca5ceb2cf312cde Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Tue, 8 Jan 2008 11:13:09 +0100 Subject: ppc4xx: Disable error message when no NAND chip is installed on PMC440 Add CFG_NAND_QUIET_TEST option to disable error message when no NAND chip is installed on PMC440 boards. Disable a couple of config defines that are only used for NAND_U_BOOT. Signed-off-by: Matthias Fuchs --- include/configs/PMC440.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'include') diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index 3d2ed1e7d64..87fca3c470f 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -167,6 +167,7 @@ * set up. While still running from cache, I experienced problems accessing * the NAND controller. sr - 2006-08-25 */ +#if defined (CONFIG_NAND_U_BOOT) #define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ #define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ #define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ @@ -195,6 +196,7 @@ #define CFG_NAND_OOBSIZE 16 #define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) #define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} +#endif #ifdef CFG_ENV_IS_IN_NAND /* @@ -501,6 +503,7 @@ #define NAND_MAX_CHIPS 1 #define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) #define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CFG_NAND_QUIET_TEST 1 /* * Internal Definitions -- cgit v1.3.1 From 6e9233d30afe57cb6e148fbfa4895e7810196fac Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Tue, 8 Jan 2008 15:50:49 +0100 Subject: ppc4xx: Move cpu/ppc4xx/vecnum.h into include path This patch allows the use of 4xx interrupt vector number defines in board specific code outside cpu/ppc4xx. Signed-off-by: Matthias Fuchs --- cpu/ppc4xx/4xx_enet.c | 2 +- cpu/ppc4xx/4xx_uart.c | 2 +- cpu/ppc4xx/interrupts.c | 2 +- cpu/ppc4xx/iop480_uart.c | 2 +- cpu/ppc4xx/usbdev.c | 2 +- cpu/ppc4xx/vecnum.h | 403 ---------------------------------------- include/asm-ppc/ppc4xx-intvec.h | 403 ++++++++++++++++++++++++++++++++++++++++ 7 files changed, 408 insertions(+), 408 deletions(-) delete mode 100644 cpu/ppc4xx/vecnum.h create mode 100644 include/asm-ppc/ppc4xx-intvec.h (limited to 'include') diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index ff707dda58d..44659ffcd98 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -90,7 +90,7 @@ #include <405_mal.h> #include #include -#include "vecnum.h" +#include /* * Only compile for platform with AMCC EMAC ethernet controller and diff --git a/cpu/ppc4xx/4xx_uart.c b/cpu/ppc4xx/4xx_uart.c index ac2b12b8773..3d1124e0b27 100644 --- a/cpu/ppc4xx/4xx_uart.c +++ b/cpu/ppc4xx/4xx_uart.c @@ -46,7 +46,7 @@ #include #include #include -#include "vecnum.h" +#include #ifdef CONFIG_SERIAL_MULTI #include diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c index 2026cc927a9..2f3dc326b46 100644 --- a/cpu/ppc4xx/interrupts.c +++ b/cpu/ppc4xx/interrupts.c @@ -34,7 +34,7 @@ #include #include #include -#include "vecnum.h" +#include DECLARE_GLOBAL_DATA_PTR; diff --git a/cpu/ppc4xx/iop480_uart.c b/cpu/ppc4xx/iop480_uart.c index 8dd226729e2..3af0767c552 100644 --- a/cpu/ppc4xx/iop480_uart.c +++ b/cpu/ppc4xx/iop480_uart.c @@ -26,7 +26,7 @@ #include #include #include -#include "vecnum.h" +#include #ifdef CONFIG_SERIAL_MULTI #include diff --git a/cpu/ppc4xx/usbdev.c b/cpu/ppc4xx/usbdev.c index 5924a6cb847..d71ba7710a0 100644 --- a/cpu/ppc4xx/usbdev.c +++ b/cpu/ppc4xx/usbdev.c @@ -7,7 +7,7 @@ #include #include "usbdev.h" -#include "vecnum.h" +#include #define USB_DT_DEVICE 0x01 #define USB_DT_CONFIG 0x02 diff --git a/cpu/ppc4xx/vecnum.h b/cpu/ppc4xx/vecnum.h deleted file mode 100644 index 8d04b690632..00000000000 --- a/cpu/ppc4xx/vecnum.h +++ /dev/null @@ -1,403 +0,0 @@ -/* -* Copyright (C) 2002 Scott McNutt -* -* See file CREDITS for list of people who contributed to this -* project. -* -* This program is free software; you can redistribute it and/or -* modify it under the terms of the GNU General Public License as -* published by the Free Software Foundation; either version 2 of -* the License, or (at your option) any later version. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License -* along with this program; if not, write to the Free Software -* Foundation, Inc., 59 Temple Place, Suite 330, Boston, -* MA 02111-1307 USA -*/ - -/* - * Interrupt vector number definitions to ease the - * 405 -- 440 porting pain ;-) - * - * NOTE: They're not all here yet ... update as needed. - * - */ - -#ifndef _VECNUMS_H_ -#define _VECNUMS_H_ - -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART 0 */ -#define VECNUM_U1 1 /* UART 1 */ -#define VECNUM_IIC0 2 /* IIC */ -#define VECNUM_KRD 3 /* Kasumi Ready for data */ -#define VECNUM_KDA 4 /* Kasumi Data Available */ -#define VECNUM_PCRW 5 /* PCI command register write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_IIC1 7 /* IIC */ -#define VECNUM_SPI 8 /* SPI */ -#define VECNUM_EPCISER 9 /* External PCI SERR */ -#define VECNUM_MTE 10 /* MAL TXEOB */ -#define VECNUM_MRE 11 /* MAL RXEOB */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_UD0 16 /* UDMA irq 0 */ -#define VECNUM_UD1 17 /* UDMA irq 1 */ -#define VECNUM_UD2 18 /* UDMA irq 2 */ -#define VECNUM_UD3 19 /* UDMA irq 3 */ -#define VECNUM_HSB2D 20 /* USB2.0 Device */ -#define VECNUM_USBDEV 20 /* USB 1.1/USB 2.0 Device */ -#define VECNUM_OHCI1 21 /* USB2.0 Host OHCI irq 1 */ -#define VECNUM_OHCI2 22 /* USB2.0 Host OHCI irq 2 */ -#define VECNUM_EIP94 23 /* Security EIP94 */ -#define VECNUM_ETH0 24 /* Emac 0 */ -#define VECNUM_ETH1 25 /* Emac 1 */ -#define VECNUM_EHCI 26 /* USB2.0 Host EHCI */ -#define VECNUM_EIR4 27 /* External interrupt 4 */ -#define VECNUM_UIC2NC 28 /* UIC2 non-critical interrupt */ -#define VECNUM_UIC2C 29 /* UIC2 critical interrupt */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 0) /* MAL SERR */ -#define VECNUM_MTDE (32 + 1) /* MAL TXDE */ -#define VECNUM_MRDE (32 + 2) /* MAL RXDE */ -#define VECNUM_U2 (32 + 3) /* UART 2 */ -#define VECNUM_U3 (32 + 4) /* UART 3 */ -#define VECNUM_EBCO (32 + 5) /* EBCO interrupt status */ -#define VECNUM_NDFC (32 + 6) /* NDFC */ -#define VECNUM_KSLE (32 + 7) /* KASUMI slave error */ -#define VECNUM_CT5 (32 + 8) /* GPT compare timer 5 */ -#define VECNUM_CT6 (32 + 9) /* GPT compare timer 6 */ -#define VECNUM_PLB34I0 (32 + 10) /* PLB3X4X MIRQ0 */ -#define VECNUM_PLB34I1 (32 + 11) /* PLB3X4X MIRQ1 */ -#define VECNUM_PLB34I2 (32 + 12) /* PLB3X4X MIRQ2 */ -#define VECNUM_PLB34I3 (32 + 13) /* PLB3X4X MIRQ3 */ -#define VECNUM_PLB34I4 (32 + 14) /* PLB3X4X MIRQ4 */ -#define VECNUM_PLB34I5 (32 + 15) /* PLB3X4X MIRQ5 */ -#define VECNUM_CT0 (32 + 16) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 17) /* GPT compare timer 1 */ -#define VECNUM_EIR7 (32 + 18) /* External interrupt 7 */ -#define VECNUM_EIR8 (32 + 19) /* External interrupt 8 */ -#define VECNUM_EIR9 (32 + 20) /* External interrupt 9 */ -#define VECNUM_CT2 (32 + 21) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 22) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 23) /* GPT compare timer 4 */ -#define VECNUM_SRE (32 + 24) /* Serial ROM error */ -#define VECNUM_GPTDC (32 + 25) /* GPT decrementer pulse */ -#define VECNUM_RSVD0 (32 + 26) /* Reserved */ -#define VECNUM_EPCIPER (32 + 27) /* External PCI PERR */ -#define VECNUM_EIR0 (32 + 28) /* External interrupt 0 */ -#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ -#define VECNUM_EIR1 (32 + 30) /* External interrupt 1 */ -#define VECNUM_EWU1 (32 + 31) /* Ethernet 1 wakeup */ - -#define VECNUM_TXDE VECNUM_MTDE -#define VECNUM_RXDE VECNUM_MRDE - -/* UIC 2 */ -#define VECNUM_EIR5 (64 + 0) /* External interrupt 5 */ -#define VECNUM_EIR6 (64 + 1) /* External interrupt 6 */ -#define VECNUM_OPB (64 + 2) /* OPB to PLB bridge int stat */ -#define VECNUM_EIR2 (64 + 3) /* External interrupt 2 */ -#define VECNUM_EIR3 (64 + 4) /* External interrupt 3 */ -#define VECNUM_DDR2 (64 + 5) /* DDR2 sdram */ -#define VECNUM_MCTX0 (64 + 6) /* MAl intp coalescence TX0 */ -#define VECNUM_MCTX1 (64 + 7) /* MAl intp coalescence TX1 */ -#define VECNUM_MCTR0 (64 + 8) /* MAl intp coalescence TR0 */ -#define VECNUM_MCTR1 (64 + 9) /* MAl intp coalescence TR1 */ - -#elif defined(CONFIG_440SPE) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_MSI0 7 /* PCI MSI level 0 */ -#define VECNUM_MSI1 8 /* PCI MSI level 0 */ -#define VECNUM_MSI2 9 /* PCI MSI level 0 */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 1 ) /* MAL SERR */ -#define VECNUM_TXDE (32 + 2 ) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 3 ) /* MAL RXDE */ -#define VECNUM_MTE (32 + 6 ) /* MAL Tx EOB */ -#define VECNUM_MRE (32 + 7 ) /* MAL Rx EOB */ -#define VECNUM_CT0 (32 + 12 ) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 13 ) /* GPT compare timer 1 */ -#define VECNUM_CT2 (32 + 14 ) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 15 ) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 16 ) /* GPT compare timer 4 */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ - -/* UIC 2 */ -#define VECNUM_EIR5 (64 + 24) /* External interrupt 5 */ -#define VECNUM_EIR4 (64 + 25) /* External interrupt 4 */ -#define VECNUM_EIR3 (64 + 26) /* External interrupt 3 */ -#define VECNUM_EIR2 (64 + 27) /* External interrupt 2 */ -#define VECNUM_EIR1 (64 + 28) /* External interrupt 1 */ -#define VECNUM_EIR0 (64 + 29) /* External interrupt 0 */ - -#elif defined(CONFIG_440SP) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_EIR0 (32 + 0) /* External interrupt 0 */ -#define VECNUM_MS (32 + 1) /* MAL SERR */ -#define VECNUM_TXDE (32 + 2) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 3) /* MAL RXDE */ -#define VECNUM_MTE (32 + 6) /* MAL Tx EOB */ -#define VECNUM_MRE (32 + 7) /* MAL Rx EOB */ -#define VECNUM_CT0 (32 + 12) /* GPT compare timer 0 */ -#define VECNUM_CT1 (32 + 13) /* GPT compare timer 1 */ -#define VECNUM_CT2 (32 + 14) /* GPT compare timer 2 */ -#define VECNUM_CT3 (32 + 15) /* GPT compare timer 3 */ -#define VECNUM_CT4 (32 + 16) /* GPT compare timer 4 */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ - -#elif defined(CONFIG_440) - -/* UIC 0 */ -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_IIC0 2 /* IIC0 */ -#define VECNUM_IIC1 3 /* IIC1 */ -#define VECNUM_PIM 4 /* PCI inbound message */ -#define VECNUM_PCRW 5 /* PCI command reg write */ -#define VECNUM_PPM 6 /* PCI power management */ -#define VECNUM_MSI0 7 /* PCI MSI level 0 */ -#define VECNUM_MSI1 8 /* PCI MSI level 0 */ -#define VECNUM_MSI2 9 /* PCI MSI level 0 */ -#define VECNUM_MTE 10 /* MAL TXEOB */ -#define VECNUM_MRE 11 /* MAL RXEOB */ -#define VECNUM_D0 12 /* DMA channel 0 */ -#define VECNUM_D1 13 /* DMA channel 1 */ -#define VECNUM_D2 14 /* DMA channel 2 */ -#define VECNUM_D3 15 /* DMA channel 3 */ -#define VECNUM_CT0 18 /* GPT compare timer 0 */ -#define VECNUM_CT1 19 /* GPT compare timer 1 */ -#define VECNUM_CT2 20 /* GPT compare timer 2 */ -#define VECNUM_CT3 21 /* GPT compare timer 3 */ -#define VECNUM_CT4 22 /* GPT compare timer 4 */ -#define VECNUM_EIR0 23 /* External interrupt 0 */ -#define VECNUM_EIR1 24 /* External interrupt 1 */ -#define VECNUM_EIR2 25 /* External interrupt 2 */ -#define VECNUM_EIR3 26 /* External interrupt 3 */ -#define VECNUM_EIR4 27 /* External interrupt 4 */ -#define VECNUM_EIR5 28 /* External interrupt 5 */ -#define VECNUM_EIR6 29 /* External interrupt 6 */ -#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ -#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ - -/* UIC 1 */ -#define VECNUM_MS (32 + 0 ) /* MAL SERR */ -#define VECNUM_TXDE (32 + 1 ) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 2 ) /* MAL RXDE */ -#define VECNUM_USBDEV (32 + 23) /* USB 1.1/USB 2.0 Device */ -#define VECNUM_ETH0 (32 + 28) /* Ethernet 0 interrupt status */ -#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ - -#else /* !defined(CONFIG_440) */ - -#if defined(CONFIG_405EZ) -#define VECNUM_D0 0 /* DMA channel 0 */ -#define VECNUM_D1 1 /* DMA channel 1 */ -#define VECNUM_D2 2 /* DMA channel 2 */ -#define VECNUM_D3 3 /* DMA channel 3 */ -#define VECNUM_1588 4 /* IEEE 1588 network synchronization */ -#define VECNUM_U0 5 /* UART0 */ -#define VECNUM_U1 6 /* UART1 */ -#define VECNUM_CAN0 7 /* CAN 0 */ -#define VECNUM_CAN1 8 /* CAN 1 */ -#define VECNUM_SPI 9 /* SPI */ -#define VECNUM_IIC0 10 /* I2C */ -#define VECNUM_CHT0 11 /* Chameleon timer high pri interrupt */ -#define VECNUM_CHT1 12 /* Chameleon timer high pri interrupt */ -#define VECNUM_USBH1 13 /* USB Host 1 */ -#define VECNUM_USBH2 14 /* USB Host 2 */ -#define VECNUM_USBDEV 15 /* USB Device */ -#define VECNUM_ETH0 16 /* 10/100 Ethernet interrupt status */ -#define VECNUM_EWU0 17 /* Ethernet wakeup sequence detected */ - -#define VECNUM_MADMAL 18 /* Logical OR of following MadMAL int */ -#define VECNUM_MS 18 /* MAL_SERR_INT */ -#define VECNUM_TXDE 18 /* MAL_TXDE_INT */ -#define VECNUM_RXDE 18 /* MAL_RXDE_INT */ - -#define VECNUM_MTE 19 /* MAL TXEOB */ -#define VECNUM_MTE1 20 /* MAL TXEOB1 */ -#define VECNUM_MRE 21 /* MAL RXEOB */ -#define VECNUM_NAND 22 /* NAND Flash controller */ -#define VECNUM_ADC 23 /* ADC */ -#define VECNUM_DAC 24 /* DAC */ -#define VECNUM_OPB2PLB 25 /* OPB to PLB bridge interrupt */ -#define VECNUM_RESERVED0 26 /* Reserved */ -#define VECNUM_EIR0 27 /* External interrupt 0 */ -#define VECNUM_EIR1 28 /* External interrupt 1 */ -#define VECNUM_EIR2 29 /* External interrupt 2 */ -#define VECNUM_EIR3 30 /* External interrupt 3 */ -#define VECNUM_EIR4 31 /* External interrupt 4 */ - -#elif defined(CONFIG_405EX) - -/* UIC 0 */ -#define VECNUM_U0 00 -#define VECNUM_U1 01 -#define VECNUM_IIC0 02 -#define VECNUM_PKA 03 -#define VECNUM_TRNG 04 -#define VECNUM_EBM 05 -#define VECNUM_BGI 06 -#define VECNUM_IIC1 07 -#define VECNUM_SPI 08 -#define VECNUM_EIR0 09 -#define VECNUM_MTE 10 /* MAL Tx EOB */ -#define VECNUM_MRE 11 /* MAL Rx EOB */ -#define VECNUM_DMA0 12 -#define VECNUM_DMA1 13 -#define VECNUM_DMA2 14 -#define VECNUM_DMA3 15 -#define VECNUM_PCIE0AL 16 -#define VECNUM_PCIE0VPD 17 -#define VECNUM_RPCIE0HRST 18 -#define VECNUM_FPCIE0HRST 19 -#define VECNUM_PCIE0TCR 20 -#define VECNUM_PCIEMSI0 21 -#define VECNUM_PCIEMSI1 22 -#define VECNUM_SECURITY 23 -#define VECNUM_ETH0 24 -#define VECNUM_ETH1 25 -#define VECNUM_PCIEMSI2 26 -#define VECNUM_EIR4 27 -#define VECNUM_UIC2NC 28 -#define VECNUM_UIC2C 29 -#define VECNUM_UIC1NC 30 -#define VECNUM_UIC1C 31 - -/* UIC 1 */ -#define VECNUM_MS (32 + 00) /* MAL SERR */ -#define VECNUM_TXDE (32 + 01) /* MAL TXDE */ -#define VECNUM_RXDE (32 + 02) /* MAL RXDE */ -#define VECNUM_PCIE0BMVC0 (32 + 03) -#define VECNUM_PCIE0DCRERR (32 + 04) -#define VECNUM_EBC (32 + 05) -#define VECNUM_NDFC (32 + 06) -#define VECNUM_PCEI1DCRERR (32 + 07) -#define VECNUM_CT8 (32 + 08) -#define VECNUM_CT9 (32 + 09) -#define VECNUM_PCIE1AL (32 + 10) -#define VECNUM_PCIE1VPD (32 + 11) -#define VECNUM_RPCE1HRST (32 + 12) -#define VECNUM_FPCE1HRST (32 + 13) -#define VECNUM_PCIE1TCR (32 + 14) -#define VECNUM_PCIE1VC0 (32 + 15) -#define VECNUM_CT3 (32 + 16) -#define VECNUM_CT4 (32 + 17) -#define VECNUM_EIR7 (32 + 18) -#define VECNUM_EIR8 (32 + 19) -#define VECNUM_EIR9 (32 + 20) -#define VECNUM_CT5 (32 + 21) -#define VECNUM_CT6 (32 + 22) -#define VECNUM_CT7 (32 + 23) -#define VECNUM_SROM (32 + 24) /* SERIAL ROM */ -#define VECNUM_GPTDECPULS (32 + 25) /* GPT Decrement pulse */ -#define VECNUM_EIR2 (32 + 26) -#define VECNUM_EIR5 (32 + 27) -#define VECNUM_EIR6 (32 + 28) -#define VECNUM_EMAC0WAKE (32 + 29) -#define VECNUM_EIR1 (32 + 30) -#define VECNUM_EMAC1WAKE (32 + 31) - -/* UIC 2 */ -#define VECNUM_PCIE0INTA (64 + 00) /* PCIE0 INTA */ -#define VECNUM_PCIE0INTB (64 + 01) /* PCIE0 INTB */ -#define VECNUM_PCIE0INTC (64 + 02) /* PCIE0 INTC */ -#define VECNUM_PCIE0INTD (64 + 03) /* PCIE0 INTD */ -#define VECNUM_EIR3 (64 + 04) /* External IRQ 3 */ -#define VECNUM_DDRMCUE (64 + 05) -#define VECNUM_DDRMCCE (64 + 06) -#define VECNUM_MALINTCOATX0 (64 + 07) /* Interrupt coalecence TX0 */ -#define VECNUM_MALINTCOATX1 (64 + 08) /* Interrupt coalecence TX1 */ -#define VECNUM_MALINTCOARX0 (64 + 09) /* Interrupt coalecence RX0 */ -#define VECNUM_MALINTCOARX1 (64 + 10) /* Interrupt coalecence RX1 */ -#define VECNUM_PCIE1INTA (64 + 11) /* PCIE0 INTA */ -#define VECNUM_PCIE1INTB (64 + 12) /* PCIE0 INTB */ -#define VECNUM_PCIE1INTC (64 + 13) /* PCIE0 INTC */ -#define VECNUM_PCIE1INTD (64 + 14) /* PCIE0 INTD */ -#define VECNUM_RPCIEMSI2 (64 + 15) /* MSI level 2 */ -#define VECNUM_PCIEMSI3 (64 + 16) /* MSI level 2 */ -#define VECNUM_PCIEMSI4 (64 + 17) /* MSI level 2 */ -#define VECNUM_PCIEMSI5 (64 + 18) /* MSI level 2 */ -#define VECNUM_PCIEMSI6 (64 + 19) /* MSI level 2 */ -#define VECNUM_PCIEMSI7 (64 + 20) /* MSI level 2 */ -#define VECNUM_PCIEMSI8 (64 + 21) /* MSI level 2 */ -#define VECNUM_PCIEMSI9 (64 + 22) /* MSI level 2 */ -#define VECNUM_PCIEMSI10 (64 + 23) /* MSI level 2 */ -#define VECNUM_PCIEMSI11 (64 + 24) /* MSI level 2 */ -#define VECNUM_PCIEMSI12 (64 + 25) /* MSI level 2 */ -#define VECNUM_PCIEMSI13 (64 + 26) /* MSI level 2 */ -#define VECNUM_PCIEMSI14 (64 + 27) /* MSI level 2 */ -#define VECNUM_PCIEMSI15 (64 + 28) /* MSI level 2 */ -#define VECNUM_PLB4XAHB (64 + 29) /* PLBxAHB bridge */ -#define VECNUM_USBWAKE (64 + 30) /* USB wakup */ -#define VECNUM_USBOTG (64 + 31) /* USB OTG */ - -#else /* !CONFIG_405EZ */ - -#define VECNUM_U0 0 /* UART0 */ -#define VECNUM_U1 1 /* UART1 */ -#define VECNUM_D0 5 /* DMA channel 0 */ -#define VECNUM_D1 6 /* DMA channel 1 */ -#define VECNUM_D2 7 /* DMA channel 2 */ -#define VECNUM_D3 8 /* DMA channel 3 */ -#define VECNUM_EWU0 9 /* Ethernet wakeup */ -#define VECNUM_MS 10 /* MAL SERR */ -#define VECNUM_MTE 11 /* MAL TXEOB */ -#define VECNUM_MRE 12 /* MAL RXEOB */ -#define VECNUM_TXDE 13 /* MAL TXDE */ -#define VECNUM_RXDE 14 /* MAL RXDE */ -#define VECNUM_ETH0 15 /* Ethernet interrupt status */ -#define VECNUM_EIR0 25 /* External interrupt 0 */ -#define VECNUM_EIR1 26 /* External interrupt 1 */ -#define VECNUM_EIR2 27 /* External interrupt 2 */ -#define VECNUM_EIR3 28 /* External interrupt 3 */ -#define VECNUM_EIR4 29 /* External interrupt 4 */ -#define VECNUM_EIR5 30 /* External interrupt 5 */ -#define VECNUM_EIR6 31 /* External interrupt 6 */ -#endif /* defined(CONFIG_405EZ) */ - -#endif /* defined(CONFIG_440) */ - -#endif /* _VECNUMS_H_ */ diff --git a/include/asm-ppc/ppc4xx-intvec.h b/include/asm-ppc/ppc4xx-intvec.h new file mode 100644 index 00000000000..8d04b690632 --- /dev/null +++ b/include/asm-ppc/ppc4xx-intvec.h @@ -0,0 +1,403 @@ +/* +* Copyright (C) 2002 Scott McNutt +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +/* + * Interrupt vector number definitions to ease the + * 405 -- 440 porting pain ;-) + * + * NOTE: They're not all here yet ... update as needed. + * + */ + +#ifndef _VECNUMS_H_ +#define _VECNUMS_H_ + +#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) + +/* UIC 0 */ +#define VECNUM_U0 0 /* UART 0 */ +#define VECNUM_U1 1 /* UART 1 */ +#define VECNUM_IIC0 2 /* IIC */ +#define VECNUM_KRD 3 /* Kasumi Ready for data */ +#define VECNUM_KDA 4 /* Kasumi Data Available */ +#define VECNUM_PCRW 5 /* PCI command register write */ +#define VECNUM_PPM 6 /* PCI power management */ +#define VECNUM_IIC1 7 /* IIC */ +#define VECNUM_SPI 8 /* SPI */ +#define VECNUM_EPCISER 9 /* External PCI SERR */ +#define VECNUM_MTE 10 /* MAL TXEOB */ +#define VECNUM_MRE 11 /* MAL RXEOB */ +#define VECNUM_D0 12 /* DMA channel 0 */ +#define VECNUM_D1 13 /* DMA channel 1 */ +#define VECNUM_D2 14 /* DMA channel 2 */ +#define VECNUM_D3 15 /* DMA channel 3 */ +#define VECNUM_UD0 16 /* UDMA irq 0 */ +#define VECNUM_UD1 17 /* UDMA irq 1 */ +#define VECNUM_UD2 18 /* UDMA irq 2 */ +#define VECNUM_UD3 19 /* UDMA irq 3 */ +#define VECNUM_HSB2D 20 /* USB2.0 Device */ +#define VECNUM_USBDEV 20 /* USB 1.1/USB 2.0 Device */ +#define VECNUM_OHCI1 21 /* USB2.0 Host OHCI irq 1 */ +#define VECNUM_OHCI2 22 /* USB2.0 Host OHCI irq 2 */ +#define VECNUM_EIP94 23 /* Security EIP94 */ +#define VECNUM_ETH0 24 /* Emac 0 */ +#define VECNUM_ETH1 25 /* Emac 1 */ +#define VECNUM_EHCI 26 /* USB2.0 Host EHCI */ +#define VECNUM_EIR4 27 /* External interrupt 4 */ +#define VECNUM_UIC2NC 28 /* UIC2 non-critical interrupt */ +#define VECNUM_UIC2C 29 /* UIC2 critical interrupt */ +#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ +#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ + +/* UIC 1 */ +#define VECNUM_MS (32 + 0) /* MAL SERR */ +#define VECNUM_MTDE (32 + 1) /* MAL TXDE */ +#define VECNUM_MRDE (32 + 2) /* MAL RXDE */ +#define VECNUM_U2 (32 + 3) /* UART 2 */ +#define VECNUM_U3 (32 + 4) /* UART 3 */ +#define VECNUM_EBCO (32 + 5) /* EBCO interrupt status */ +#define VECNUM_NDFC (32 + 6) /* NDFC */ +#define VECNUM_KSLE (32 + 7) /* KASUMI slave error */ +#define VECNUM_CT5 (32 + 8) /* GPT compare timer 5 */ +#define VECNUM_CT6 (32 + 9) /* GPT compare timer 6 */ +#define VECNUM_PLB34I0 (32 + 10) /* PLB3X4X MIRQ0 */ +#define VECNUM_PLB34I1 (32 + 11) /* PLB3X4X MIRQ1 */ +#define VECNUM_PLB34I2 (32 + 12) /* PLB3X4X MIRQ2 */ +#define VECNUM_PLB34I3 (32 + 13) /* PLB3X4X MIRQ3 */ +#define VECNUM_PLB34I4 (32 + 14) /* PLB3X4X MIRQ4 */ +#define VECNUM_PLB34I5 (32 + 15) /* PLB3X4X MIRQ5 */ +#define VECNUM_CT0 (32 + 16) /* GPT compare timer 0 */ +#define VECNUM_CT1 (32 + 17) /* GPT compare timer 1 */ +#define VECNUM_EIR7 (32 + 18) /* External interrupt 7 */ +#define VECNUM_EIR8 (32 + 19) /* External interrupt 8 */ +#define VECNUM_EIR9 (32 + 20) /* External interrupt 9 */ +#define VECNUM_CT2 (32 + 21) /* GPT compare timer 2 */ +#define VECNUM_CT3 (32 + 22) /* GPT compare timer 3 */ +#define VECNUM_CT4 (32 + 23) /* GPT compare timer 4 */ +#define VECNUM_SRE (32 + 24) /* Serial ROM error */ +#define VECNUM_GPTDC (32 + 25) /* GPT decrementer pulse */ +#define VECNUM_RSVD0 (32 + 26) /* Reserved */ +#define VECNUM_EPCIPER (32 + 27) /* External PCI PERR */ +#define VECNUM_EIR0 (32 + 28) /* External interrupt 0 */ +#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ +#define VECNUM_EIR1 (32 + 30) /* External interrupt 1 */ +#define VECNUM_EWU1 (32 + 31) /* Ethernet 1 wakeup */ + +#define VECNUM_TXDE VECNUM_MTDE +#define VECNUM_RXDE VECNUM_MRDE + +/* UIC 2 */ +#define VECNUM_EIR5 (64 + 0) /* External interrupt 5 */ +#define VECNUM_EIR6 (64 + 1) /* External interrupt 6 */ +#define VECNUM_OPB (64 + 2) /* OPB to PLB bridge int stat */ +#define VECNUM_EIR2 (64 + 3) /* External interrupt 2 */ +#define VECNUM_EIR3 (64 + 4) /* External interrupt 3 */ +#define VECNUM_DDR2 (64 + 5) /* DDR2 sdram */ +#define VECNUM_MCTX0 (64 + 6) /* MAl intp coalescence TX0 */ +#define VECNUM_MCTX1 (64 + 7) /* MAl intp coalescence TX1 */ +#define VECNUM_MCTR0 (64 + 8) /* MAl intp coalescence TR0 */ +#define VECNUM_MCTR1 (64 + 9) /* MAl intp coalescence TR1 */ + +#elif defined(CONFIG_440SPE) + +/* UIC 0 */ +#define VECNUM_U0 0 /* UART0 */ +#define VECNUM_U1 1 /* UART1 */ +#define VECNUM_IIC0 2 /* IIC0 */ +#define VECNUM_IIC1 3 /* IIC1 */ +#define VECNUM_PIM 4 /* PCI inbound message */ +#define VECNUM_PCRW 5 /* PCI command reg write */ +#define VECNUM_PPM 6 /* PCI power management */ +#define VECNUM_MSI0 7 /* PCI MSI level 0 */ +#define VECNUM_MSI1 8 /* PCI MSI level 0 */ +#define VECNUM_MSI2 9 /* PCI MSI level 0 */ +#define VECNUM_D0 12 /* DMA channel 0 */ +#define VECNUM_D1 13 /* DMA channel 1 */ +#define VECNUM_D2 14 /* DMA channel 2 */ +#define VECNUM_D3 15 /* DMA channel 3 */ +#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ +#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ + +/* UIC 1 */ +#define VECNUM_MS (32 + 1 ) /* MAL SERR */ +#define VECNUM_TXDE (32 + 2 ) /* MAL TXDE */ +#define VECNUM_RXDE (32 + 3 ) /* MAL RXDE */ +#define VECNUM_MTE (32 + 6 ) /* MAL Tx EOB */ +#define VECNUM_MRE (32 + 7 ) /* MAL Rx EOB */ +#define VECNUM_CT0 (32 + 12 ) /* GPT compare timer 0 */ +#define VECNUM_CT1 (32 + 13 ) /* GPT compare timer 1 */ +#define VECNUM_CT2 (32 + 14 ) /* GPT compare timer 2 */ +#define VECNUM_CT3 (32 + 15 ) /* GPT compare timer 3 */ +#define VECNUM_CT4 (32 + 16 ) /* GPT compare timer 4 */ +#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ +#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ + +/* UIC 2 */ +#define VECNUM_EIR5 (64 + 24) /* External interrupt 5 */ +#define VECNUM_EIR4 (64 + 25) /* External interrupt 4 */ +#define VECNUM_EIR3 (64 + 26) /* External interrupt 3 */ +#define VECNUM_EIR2 (64 + 27) /* External interrupt 2 */ +#define VECNUM_EIR1 (64 + 28) /* External interrupt 1 */ +#define VECNUM_EIR0 (64 + 29) /* External interrupt 0 */ + +#elif defined(CONFIG_440SP) + +/* UIC 0 */ +#define VECNUM_U0 0 /* UART0 */ +#define VECNUM_U1 1 /* UART1 */ +#define VECNUM_IIC0 2 /* IIC0 */ +#define VECNUM_IIC1 3 /* IIC1 */ +#define VECNUM_PIM 4 /* PCI inbound message */ +#define VECNUM_PCRW 5 /* PCI command reg write */ +#define VECNUM_PPM 6 /* PCI power management */ +#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ +#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ + +/* UIC 1 */ +#define VECNUM_EIR0 (32 + 0) /* External interrupt 0 */ +#define VECNUM_MS (32 + 1) /* MAL SERR */ +#define VECNUM_TXDE (32 + 2) /* MAL TXDE */ +#define VECNUM_RXDE (32 + 3) /* MAL RXDE */ +#define VECNUM_MTE (32 + 6) /* MAL Tx EOB */ +#define VECNUM_MRE (32 + 7) /* MAL Rx EOB */ +#define VECNUM_CT0 (32 + 12) /* GPT compare timer 0 */ +#define VECNUM_CT1 (32 + 13) /* GPT compare timer 1 */ +#define VECNUM_CT2 (32 + 14) /* GPT compare timer 2 */ +#define VECNUM_CT3 (32 + 15) /* GPT compare timer 3 */ +#define VECNUM_CT4 (32 + 16) /* GPT compare timer 4 */ +#define VECNUM_ETH0 (32 + 28) /* Ethernet interrupt status */ +#define VECNUM_EWU0 (32 + 29) /* Emac wakeup */ + +#elif defined(CONFIG_440) + +/* UIC 0 */ +#define VECNUM_U0 0 /* UART0 */ +#define VECNUM_U1 1 /* UART1 */ +#define VECNUM_IIC0 2 /* IIC0 */ +#define VECNUM_IIC1 3 /* IIC1 */ +#define VECNUM_PIM 4 /* PCI inbound message */ +#define VECNUM_PCRW 5 /* PCI command reg write */ +#define VECNUM_PPM 6 /* PCI power management */ +#define VECNUM_MSI0 7 /* PCI MSI level 0 */ +#define VECNUM_MSI1 8 /* PCI MSI level 0 */ +#define VECNUM_MSI2 9 /* PCI MSI level 0 */ +#define VECNUM_MTE 10 /* MAL TXEOB */ +#define VECNUM_MRE 11 /* MAL RXEOB */ +#define VECNUM_D0 12 /* DMA channel 0 */ +#define VECNUM_D1 13 /* DMA channel 1 */ +#define VECNUM_D2 14 /* DMA channel 2 */ +#define VECNUM_D3 15 /* DMA channel 3 */ +#define VECNUM_CT0 18 /* GPT compare timer 0 */ +#define VECNUM_CT1 19 /* GPT compare timer 1 */ +#define VECNUM_CT2 20 /* GPT compare timer 2 */ +#define VECNUM_CT3 21 /* GPT compare timer 3 */ +#define VECNUM_CT4 22 /* GPT compare timer 4 */ +#define VECNUM_EIR0 23 /* External interrupt 0 */ +#define VECNUM_EIR1 24 /* External interrupt 1 */ +#define VECNUM_EIR2 25 /* External interrupt 2 */ +#define VECNUM_EIR3 26 /* External interrupt 3 */ +#define VECNUM_EIR4 27 /* External interrupt 4 */ +#define VECNUM_EIR5 28 /* External interrupt 5 */ +#define VECNUM_EIR6 29 /* External interrupt 6 */ +#define VECNUM_UIC1NC 30 /* UIC1 non-critical interrupt */ +#define VECNUM_UIC1C 31 /* UIC1 critical interrupt */ + +/* UIC 1 */ +#define VECNUM_MS (32 + 0 ) /* MAL SERR */ +#define VECNUM_TXDE (32 + 1 ) /* MAL TXDE */ +#define VECNUM_RXDE (32 + 2 ) /* MAL RXDE */ +#define VECNUM_USBDEV (32 + 23) /* USB 1.1/USB 2.0 Device */ +#define VECNUM_ETH0 (32 + 28) /* Ethernet 0 interrupt status */ +#define VECNUM_EWU0 (32 + 29) /* Ethernet 0 wakeup */ + +#else /* !defined(CONFIG_440) */ + +#if defined(CONFIG_405EZ) +#define VECNUM_D0 0 /* DMA channel 0 */ +#define VECNUM_D1 1 /* DMA channel 1 */ +#define VECNUM_D2 2 /* DMA channel 2 */ +#define VECNUM_D3 3 /* DMA channel 3 */ +#define VECNUM_1588 4 /* IEEE 1588 network synchronization */ +#define VECNUM_U0 5 /* UART0 */ +#define VECNUM_U1 6 /* UART1 */ +#define VECNUM_CAN0 7 /* CAN 0 */ +#define VECNUM_CAN1 8 /* CAN 1 */ +#define VECNUM_SPI 9 /* SPI */ +#define VECNUM_IIC0 10 /* I2C */ +#define VECNUM_CHT0 11 /* Chameleon timer high pri interrupt */ +#define VECNUM_CHT1 12 /* Chameleon timer high pri interrupt */ +#define VECNUM_USBH1 13 /* USB Host 1 */ +#define VECNUM_USBH2 14 /* USB Host 2 */ +#define VECNUM_USBDEV 15 /* USB Device */ +#define VECNUM_ETH0 16 /* 10/100 Ethernet interrupt status */ +#define VECNUM_EWU0 17 /* Ethernet wakeup sequence detected */ + +#define VECNUM_MADMAL 18 /* Logical OR of following MadMAL int */ +#define VECNUM_MS 18 /* MAL_SERR_INT */ +#define VECNUM_TXDE 18 /* MAL_TXDE_INT */ +#define VECNUM_RXDE 18 /* MAL_RXDE_INT */ + +#define VECNUM_MTE 19 /* MAL TXEOB */ +#define VECNUM_MTE1 20 /* MAL TXEOB1 */ +#define VECNUM_MRE 21 /* MAL RXEOB */ +#define VECNUM_NAND 22 /* NAND Flash controller */ +#define VECNUM_ADC 23 /* ADC */ +#define VECNUM_DAC 24 /* DAC */ +#define VECNUM_OPB2PLB 25 /* OPB to PLB bridge interrupt */ +#define VECNUM_RESERVED0 26 /* Reserved */ +#define VECNUM_EIR0 27 /* External interrupt 0 */ +#define VECNUM_EIR1 28 /* External interrupt 1 */ +#define VECNUM_EIR2 29 /* External interrupt 2 */ +#define VECNUM_EIR3 30 /* External interrupt 3 */ +#define VECNUM_EIR4 31 /* External interrupt 4 */ + +#elif defined(CONFIG_405EX) + +/* UIC 0 */ +#define VECNUM_U0 00 +#define VECNUM_U1 01 +#define VECNUM_IIC0 02 +#define VECNUM_PKA 03 +#define VECNUM_TRNG 04 +#define VECNUM_EBM 05 +#define VECNUM_BGI 06 +#define VECNUM_IIC1 07 +#define VECNUM_SPI 08 +#define VECNUM_EIR0 09 +#define VECNUM_MTE 10 /* MAL Tx EOB */ +#define VECNUM_MRE 11 /* MAL Rx EOB */ +#define VECNUM_DMA0 12 +#define VECNUM_DMA1 13 +#define VECNUM_DMA2 14 +#define VECNUM_DMA3 15 +#define VECNUM_PCIE0AL 16 +#define VECNUM_PCIE0VPD 17 +#define VECNUM_RPCIE0HRST 18 +#define VECNUM_FPCIE0HRST 19 +#define VECNUM_PCIE0TCR 20 +#define VECNUM_PCIEMSI0 21 +#define VECNUM_PCIEMSI1 22 +#define VECNUM_SECURITY 23 +#define VECNUM_ETH0 24 +#define VECNUM_ETH1 25 +#define VECNUM_PCIEMSI2 26 +#define VECNUM_EIR4 27 +#define VECNUM_UIC2NC 28 +#define VECNUM_UIC2C 29 +#define VECNUM_UIC1NC 30 +#define VECNUM_UIC1C 31 + +/* UIC 1 */ +#define VECNUM_MS (32 + 00) /* MAL SERR */ +#define VECNUM_TXDE (32 + 01) /* MAL TXDE */ +#define VECNUM_RXDE (32 + 02) /* MAL RXDE */ +#define VECNUM_PCIE0BMVC0 (32 + 03) +#define VECNUM_PCIE0DCRERR (32 + 04) +#define VECNUM_EBC (32 + 05) +#define VECNUM_NDFC (32 + 06) +#define VECNUM_PCEI1DCRERR (32 + 07) +#define VECNUM_CT8 (32 + 08) +#define VECNUM_CT9 (32 + 09) +#define VECNUM_PCIE1AL (32 + 10) +#define VECNUM_PCIE1VPD (32 + 11) +#define VECNUM_RPCE1HRST (32 + 12) +#define VECNUM_FPCE1HRST (32 + 13) +#define VECNUM_PCIE1TCR (32 + 14) +#define VECNUM_PCIE1VC0 (32 + 15) +#define VECNUM_CT3 (32 + 16) +#define VECNUM_CT4 (32 + 17) +#define VECNUM_EIR7 (32 + 18) +#define VECNUM_EIR8 (32 + 19) +#define VECNUM_EIR9 (32 + 20) +#define VECNUM_CT5 (32 + 21) +#define VECNUM_CT6 (32 + 22) +#define VECNUM_CT7 (32 + 23) +#define VECNUM_SROM (32 + 24) /* SERIAL ROM */ +#define VECNUM_GPTDECPULS (32 + 25) /* GPT Decrement pulse */ +#define VECNUM_EIR2 (32 + 26) +#define VECNUM_EIR5 (32 + 27) +#define VECNUM_EIR6 (32 + 28) +#define VECNUM_EMAC0WAKE (32 + 29) +#define VECNUM_EIR1 (32 + 30) +#define VECNUM_EMAC1WAKE (32 + 31) + +/* UIC 2 */ +#define VECNUM_PCIE0INTA (64 + 00) /* PCIE0 INTA */ +#define VECNUM_PCIE0INTB (64 + 01) /* PCIE0 INTB */ +#define VECNUM_PCIE0INTC (64 + 02) /* PCIE0 INTC */ +#define VECNUM_PCIE0INTD (64 + 03) /* PCIE0 INTD */ +#define VECNUM_EIR3 (64 + 04) /* External IRQ 3 */ +#define VECNUM_DDRMCUE (64 + 05) +#define VECNUM_DDRMCCE (64 + 06) +#define VECNUM_MALINTCOATX0 (64 + 07) /* Interrupt coalecence TX0 */ +#define VECNUM_MALINTCOATX1 (64 + 08) /* Interrupt coalecence TX1 */ +#define VECNUM_MALINTCOARX0 (64 + 09) /* Interrupt coalecence RX0 */ +#define VECNUM_MALINTCOARX1 (64 + 10) /* Interrupt coalecence RX1 */ +#define VECNUM_PCIE1INTA (64 + 11) /* PCIE0 INTA */ +#define VECNUM_PCIE1INTB (64 + 12) /* PCIE0 INTB */ +#define VECNUM_PCIE1INTC (64 + 13) /* PCIE0 INTC */ +#define VECNUM_PCIE1INTD (64 + 14) /* PCIE0 INTD */ +#define VECNUM_RPCIEMSI2 (64 + 15) /* MSI level 2 */ +#define VECNUM_PCIEMSI3 (64 + 16) /* MSI level 2 */ +#define VECNUM_PCIEMSI4 (64 + 17) /* MSI level 2 */ +#define VECNUM_PCIEMSI5 (64 + 18) /* MSI level 2 */ +#define VECNUM_PCIEMSI6 (64 + 19) /* MSI level 2 */ +#define VECNUM_PCIEMSI7 (64 + 20) /* MSI level 2 */ +#define VECNUM_PCIEMSI8 (64 + 21) /* MSI level 2 */ +#define VECNUM_PCIEMSI9 (64 + 22) /* MSI level 2 */ +#define VECNUM_PCIEMSI10 (64 + 23) /* MSI level 2 */ +#define VECNUM_PCIEMSI11 (64 + 24) /* MSI level 2 */ +#define VECNUM_PCIEMSI12 (64 + 25) /* MSI level 2 */ +#define VECNUM_PCIEMSI13 (64 + 26) /* MSI level 2 */ +#define VECNUM_PCIEMSI14 (64 + 27) /* MSI level 2 */ +#define VECNUM_PCIEMSI15 (64 + 28) /* MSI level 2 */ +#define VECNUM_PLB4XAHB (64 + 29) /* PLBxAHB bridge */ +#define VECNUM_USBWAKE (64 + 30) /* USB wakup */ +#define VECNUM_USBOTG (64 + 31) /* USB OTG */ + +#else /* !CONFIG_405EZ */ + +#define VECNUM_U0 0 /* UART0 */ +#define VECNUM_U1 1 /* UART1 */ +#define VECNUM_D0 5 /* DMA channel 0 */ +#define VECNUM_D1 6 /* DMA channel 1 */ +#define VECNUM_D2 7 /* DMA channel 2 */ +#define VECNUM_D3 8 /* DMA channel 3 */ +#define VECNUM_EWU0 9 /* Ethernet wakeup */ +#define VECNUM_MS 10 /* MAL SERR */ +#define VECNUM_MTE 11 /* MAL TXEOB */ +#define VECNUM_MRE 12 /* MAL RXEOB */ +#define VECNUM_TXDE 13 /* MAL TXDE */ +#define VECNUM_RXDE 14 /* MAL RXDE */ +#define VECNUM_ETH0 15 /* Ethernet interrupt status */ +#define VECNUM_EIR0 25 /* External interrupt 0 */ +#define VECNUM_EIR1 26 /* External interrupt 1 */ +#define VECNUM_EIR2 27 /* External interrupt 2 */ +#define VECNUM_EIR3 28 /* External interrupt 3 */ +#define VECNUM_EIR4 29 /* External interrupt 4 */ +#define VECNUM_EIR5 30 /* External interrupt 5 */ +#define VECNUM_EIR6 31 /* External interrupt 6 */ +#endif /* defined(CONFIG_405EZ) */ + +#endif /* defined(CONFIG_440) */ + +#endif /* _VECNUMS_H_ */ -- cgit v1.3.1 From 32d6f1bc09175f3b77469771e839bc7255a9f22e Mon Sep 17 00:00:00 2001 From: Markus Klotzbücher Date: Tue, 5 Jan 1988 08:17:15 +0100 Subject: Fix problems with usb storage devices on MPC5200 /TQM5200 The MPC5200 OHCI controller operates in big endian, so CFG_OHCI_BE_CONTROLLER must be defined for it to work properly. Signed-off-by: Markus Klotzbuecher --- include/configs/TQM5200.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 7ecc275a1cd..9a0e9b84afa 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -131,6 +131,7 @@ /* USB */ #if defined(CONFIG_STK52XX) || defined(CONFIG_FO300) #define CONFIG_USB_OHCI_NEW +#define CFG_OHCI_BE_CONTROLLER #define CONFIG_USB_STORAGE #define CONFIG_CMD_FAT #define CONFIG_CMD_USB -- cgit v1.3.1 From 8f24e0637ae113500d8bd60d80d57afcc0aa8bde Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 9 Jan 2008 10:28:20 +0100 Subject: ppc4xx: Change LWMON5 to not use OCM for init-ram and POST anymore This patch configures the LWMON5 port to use d-cache as init-ram and the unused GPT0_COMP6 as POST WORD storage. Signed-off-by: Stefan Roese --- board/lwmon5/init.S | 2 +- include/configs/lwmon5.h | 19 ++++++++++++------- include/ppc440.h | 4 +--- 3 files changed, 14 insertions(+), 11 deletions(-) (limited to 'include') diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S index 6798e80985d..5aade72b52f 100644 --- a/board/lwmon5/init.S +++ b/board/lwmon5/init.S @@ -57,7 +57,7 @@ tlbtab: #ifdef CFG_INIT_RAM_DCACHE /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry(CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G) + tlbentry(CFG_INIT_RAM_ADDR, SZ_4K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G) #endif /* TLB-entry for PCI Memory */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 5210024d8f2..0bf536b6b59 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -71,15 +71,20 @@ /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ -/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ -#define CFG_OCM_DATA_ADDR CFG_OCM_BASE - +/* + * On LWMON5 we use D-cache as init-ram and stack pointer. We also move + * the POST_WORD from OCM to a 440EPx register that preserves it's + * content during reset (GPT0_COM6). This way we reserve the OCM (16k) + * for logbuffer only. + */ +#define CFG_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ #define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6) + /* unused GPT0 COMP reg */ /*----------------------------------------------------------------------- * Serial Port diff --git a/include/ppc440.h b/include/ppc440.h index 90e56b0989e..b0d16fb4a7d 100644 --- a/include/ppc440.h +++ b/include/ppc440.h @@ -1354,8 +1354,6 @@ #define plb1_bearl (PLB_ARBITER_BASE+ 0x0C) #define plb1_bearh (PLB_ARBITER_BASE+ 0x0D) -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) /* Pin Function Control Register 1 */ #define SDR0_PFC1 0x4101 #define SDR0_PFC1_U1ME_MASK 0x02000000 /* UART1 Mode Enable */ @@ -1421,7 +1419,7 @@ #define SDR0_MFR_PKT_REJ_EN1 0x00080000 /* Pkt Rej. Enable on EMAC3(1) */ #define SDR0_MFR_PKT_REJ_POL 0x00200000 /* Packet Reject Polarity */ -#endif /* defined(CONFIG_440EP) || defined(CONFIG_440GR) */ +#define GPT0_COMP6 0x00000098 #if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) #define SDR0_USB2D0CR 0x0320 -- cgit v1.3.1 From 435dc8fcdb3bc61d3d490773a8f369f98a20c868 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Wed, 9 Jan 2008 11:36:21 +0100 Subject: Coding Style cleanup, update CHANGELOG Signed-off-by: Wolfgang Denk --- CHANGELOG | 4815 ++++++++++++++++++++++++++--------- board/apollon/lowlevel_init.S | 248 +- board/freescale/common/fsl_diu_fb.c | 6 - include/configs/apollon.h | 18 +- 4 files changed, 3815 insertions(+), 1272 deletions(-) (limited to 'include') diff --git a/CHANGELOG b/CHANGELOG index ef5c7ea98b5..d682b96f672 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,1748 +1,4264 @@ -commit 467bcee11fe26ad422f2de971aa70866079870f2 -Author: Haavard Skinnemoen -Date: Fri Dec 14 15:36:18 2007 +0100 +commit b2e2142c500c48a57f18f9dd30e66c13caea0971 +Author: Stefan Roese +Date: Wed Jan 9 10:38:58 2008 +0100 - cfi_flash: Add manufacturer-specific fixups + POST: Execute SPR test after relocation - Run fixups based on the JEDEC manufacturer ID independent of the - command set ID. + On LWMON5 we now use d-cache as init-ram and stack. The SPR POST test uses + self modifying code and this doesn't work with stack in d-cache, since + I can't move the code from d-cache to i-cache. We move the SPR test to + be executed a little later, after relocation. Then stack is located in + SDRAM and this self-modifying code is no problem anymore. - This changes current behaviour: Previously, geometry reversal for AMD - chips were done based on the command set ID, while they are now done - based on the JEDEC manufacturer and device ID. + Signed-off-by: Stefan Roese - Also add fixup for top-boot Atmel chips. A fixup is needed for - AT49BV6416(T) too, but since u-boot currently only reads the low byte - of the device ID, there's no way to tell it apart from AT49BV642D, - which should not have this fixup. Since AT49BV642D support is - necessary to get ATNGW100 board support into mainline, I've commented - out the fixup for now. +commit 8f24e0637ae113500d8bd60d80d57afcc0aa8bde +Author: Stefan Roese +Date: Wed Jan 9 10:28:20 2008 +0100 - Signed-off-by: Haavard Skinnemoen + ppc4xx: Change LWMON5 to not use OCM for init-ram and POST anymore -commit 0ddf06ddf6b4bd057ad4c5f0dffea7870ba06a2a -Author: Haavard Skinnemoen -Date: Fri Dec 14 15:36:17 2007 +0100 + This patch configures the LWMON5 port to use d-cache as init-ram and + the unused GPT0_COMP6 as POST WORD storage. - cfi_flash: Add cmdset-specific init functions + Signed-off-by: Stefan Roese - Move things like reading JEDEC IDs and fixing up geometry reversal - into separate functions. The geometry reversal fixup is now performed - by altering the qry structure directly, which makes the sector init - code slightly cleaner. +commit 1754f50b710194f886b6f2831803d8960171a14d +Author: Stefan Roese +Date: Wed Jan 9 10:25:46 2008 +0100 - Signed-off-by: Haavard Skinnemoen + ppc4xx: Add CFG_POST_ALT_WORD_ADDR to support non OCM POST WORD storage -commit e23741f4a6d8047520ef0d4971762749b3587d32 -Author: Haavard Skinnemoen -Date: Fri Dec 14 15:36:16 2007 +0100 + The privious 4xx POST implementation only supported storing the POST + WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer + we need to store the POST WORD in some other non volatile location. + This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such + a location. - cfi_flash: Read whole QRY structure in one go + Signed-off-by: Stefan Roese - Read out the whole CFI Standard Query structure after successful cfi - identification. This allows subsequent code to access this information - directly without having to go through flash_read_uchar() and friends. +commit e02c521d94b45d7b05aa522e4ccde6b74bf5fe57 +Author: Stefan Roese +Date: Wed Jan 9 10:23:16 2008 +0100 - Signed-off-by: Haavard Skinnemoen + ppc4xx: Add 44x cache locking to better support init-ram in d-cache -commit df9c25ea04b38a0e05d4f8c73c5cc144cdafa7db -Author: Haavard Skinnemoen -Date: Mon Dec 17 11:02:44 2007 +0100 + This patch adds support for locking the init-ram/stack in d-cache, + so that other regions may use d-cache as well - AVR32: Fix logic inversion in disable_interrupts() + Note, that this current implementation locks exactly 4k of d-cache, + so please make sure that you don't define a bigger init-ram area. Take + a look at the lwmon5 440EPx implementation as a reference. - disable_interrupts() should return nonzero if interrupts were - _enabled_ before, not disabled. + Signed-off-by: Stefan Roese - Signed-off-by: Haavard Skinnemoen +commit 0ddb89601a8d29e808db450366752ffdc6267c53 +Author: Wolfgang Denk +Date: Wed Jan 9 10:16:33 2008 +0100 -commit acac475212cbedb17b321a363a1c878e2b47b37f -Author: Haavard Skinnemoen -Date: Fri Dec 14 16:51:22 2007 +0100 + Fix memset bug in ext2fs_read_file() - AVR32: Enable interrupts at bootup + ext2fs_read_file() had the function arguments swapped. - The timer code depends on the timer interrupt to keep track of the - upper 32 bits of the cycle counter. This obviously doesn't work when - interrupts are disabled the whole time. + Pointed out by Mike Montour, 19 Dec 2007 22:34:25 -0800 - Signed-off-by: Haavard Skinnemoen + Signed-off-by: Wolfgang Denk -commit 9570bcd87f4db255514f43b6701746c412f8fef0 -Author: Haavard Skinnemoen -Date: Thu Nov 15 10:03:45 2007 +0100 +commit 32d6f1bc09175f3b77469771e839bc7255a9f22e +Author: Markus Klotzbücher +Date: Tue Jan 5 08:17:15 1988 +0100 - AVR32: Fix wrong pin setup for USART3 + Fix problems with usb storage devices on MPC5200 /TQM5200 - As reported by Gerhard Berghofer: + The MPC5200 OHCI controller operates in big endian, so + CFG_OHCI_BE_CONTROLLER must be defined for it to work properly. - in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18 - instead of PB18 and PB19. + Signed-off-by: Markus Klotzbuecher - which is obviously correct. There's currently no code that uses - USART3, but custom boards may run into problems. +commit 46f6e5019048b103d7693d5310de0f1cfbaf4c19 +Author: Wolfgang Denk +Date: Tue Jan 8 22:58:27 2008 +0100 - Signed-off-by: Haavard Skinnemoen + Fix compile problem with new env code. -commit 09ea0de03dcc3ee7af045b0b572227bda2c1c918 -Author: Haavard Skinnemoen -Date: Thu Nov 1 12:44:20 2007 +0100 + Signed-off-by: Wolfgang Denk - README: Remove ATSTK1000 daughterboard list +commit 64b3727b9779d86127cd576e392a987de5ebb9fd +Author: Markus Klotzbücher +Date: Tue Nov 27 10:23:20 2007 +0100 - As noted by Kim Phillips, these lists tend to become out of date. + tools: fix fw_printenv tool to compile again - Signed-off-by: Haavard Skinnemoen + This patch updates the fw_printenv/fw_setenv userspace tool to include + the correct MTD header in order to compile against current kernel + headers. Backward compatibility is preserved by introducing an option + MTD_VERSION which can be set to "old" for compilation using the old MTD + headers. Along with this a number of warnings are fixed. -commit c81cbbad21cb0ae983e2e796211202234cdc8be2 -Author: Haavard Skinnemoen -Date: Tue Oct 30 14:56:36 2007 +0100 + Signed-off-by: Markus Klotzbuecher - Add ATSTK100[234] to MAINTAINERS +commit 1f84021a85abeb837d2ce0dc84297b4f1d45d516 +Author: Matthias Fuchs +Date: Tue Jan 8 15:40:09 2008 +0100 - Add all the ATSTK1000 daughterboards to MAINTAINERS along with their - "mother". Also update the entry for ATSTK1000 to be not only about the - AP7000 CPU; it's intended to handle all CPUs in the AT32AP family. + ppc4xx: assign PCI interrupts on seuqoia boards - Signed-off-by: Haavard Skinnemoen + Some operating systems rely on assigned PCI interrupts. -commit 64ff2357b1727213803591813dbc779c924bf772 -Author: Haavard Skinnemoen -Date: Mon Oct 29 13:02:54 2007 +0100 + Signed-off-by: Matthias Fuchs - AVR32: Add support for the ATSTK1004 board +commit 6e9233d30afe57cb6e148fbfa4895e7810196fac +Author: Matthias Fuchs +Date: Tue Jan 8 15:50:49 2008 +0100 - ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU, - which is a derivative of AT32AP7000. + ppc4xx: Move cpu/ppc4xx/vecnum.h into include path - Signed-off-by: Haavard Skinnemoen + This patch allows the use of 4xx interrupt vector number defines + in board specific code outside cpu/ppc4xx. -commit 667568db157f374b85abd7e03596ddd1f0b25681 -Author: Haavard Skinnemoen -Date: Mon Oct 29 13:02:54 2007 +0100 + Signed-off-by: Matthias Fuchs - AVR32: Add support for the ATSTK1003 board +commit 580d1d3186a2bc6dbdb626941b716dae1788e51e +Author: Matthias Fuchs +Date: Tue Jan 8 15:39:01 2008 +0100 - ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU, - which is a derivative of AT32AP7000. + ppc4xx: Fix UIC2 vector number base - Signed-off-by: Haavard Skinnemoen + Signed-off-by: Matthias Fuchs -commit 5fee84a794a51ec830548cda485a770efb018b92 -Author: Haavard Skinnemoen -Date: Mon Oct 29 13:23:33 2007 +0100 +commit ff5fb8a6ccba56e3482d0e297d8cfb7faa040811 +Author: Matthias Fuchs +Date: Tue Jan 8 12:49:58 2008 +0100 - AVR32: Make some AT32AP700x peripherals optional + ppc4xx: Update PLB/PCI divider for PMC440 board - Add a chip-features file providing definitions of the form + This patch updates the PLB/PCI divider when running at + 400MHz CPU frequency from 4 to 3 which results in 44MHz PCI sync clock. - AT32AP700x_CHIP_HAS_ + Signed-off-by: Matthias Fuchs - to indicate the availability of the given peripheral on the currently - selected chip. +commit 7d5d75633174867316a0c0f2fca5ceb2cf312cde +Author: Matthias Fuchs +Date: Tue Jan 8 11:13:09 2008 +0100 - Signed-off-by: Haavard Skinnemoen + ppc4xx: Disable error message when no NAND chip is installed on PMC440 -commit 36f28f8a9605ee5dcfa330482cfc62171261af97 -Author: Haavard Skinnemoen -Date: Mon Oct 29 13:09:56 2007 +0100 + Add CFG_NAND_QUIET_TEST option to disable error message when + no NAND chip is installed on PMC440 boards. - AVR32: Rename at32ap7000 -> at32ap700x + Disable a couple of config defines that are only used for NAND_U_BOOT. - The SoC-specific code for all the AT32AP700x CPUs is practically - identical; the only difference is that some chips have less features - than others. By doing this rename, we can add support for the AP7000 - derivatives simply by making some features conditional. + Signed-off-by: Matthias Fuchs - Signed-off-by: Haavard Skinnemoen +commit ad3006fe7e84667021753b74247b0bafd97ba35f +Author: Gerald Van Baren +Date: Mon Jan 7 23:47:32 2008 -0500 -commit 4d5fa99c73f354e7cf985efcf417ea55ca2f6a5e -Author: Haavard Skinnemoen -Date: Fri Jun 29 18:22:34 2007 +0200 + LIBFDT: use memmove() instead of memcpy() - atmel_mci: Show SR when block read fails + This is partial patch from the DTC/libfdt + commit 67b6b33b9b413a450a72135b5dc59c0a1e33e647 + Author: David Gibson + Date: Wed Nov 21 11:56:14 2007 +1100 - Show controller status as well as card status when an error occurs - during block read. + The patch also fixes one genuine bug caught by valgrind - + _packblocks() in fdt_rw.c was using memcpy() where it should have been + using memmove(). - Signed-off-by: Haavard Skinnemoen + Signed-off-by: Gerald Van Baren -commit 12d30aa79779c2aa7a998bbae4c075f822a53004 -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:34 2007 +0100 +commit aec7135bc300e3340d18f203347ee00c5b5f68c0 +Author: David Gibson +Date: Mon Dec 17 14:42:07 2007 +1100 - cfi_flash: Use map_physmem() and unmap_physmem() + libfdt: Add more documentation (patch the seventh) - Use map_physmem() and unmap_physmem() to convert from physical to - virtual addresses. This gives the arch a chance to provide an uncached - mapping for flash accesses. + This patch adds more documenting comments to libfdt.h. Specifically, + these document the read/write functions (not including fdt_open_into() + and fdt_pack(), for now). - Signed-off-by: Haavard Skinnemoen + Signed-off-by: David Gibson -commit 4d7d6936eb29af7cca330937808312aa5f61454d -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:33 2007 +0100 +commit 9d4450b5adc36623e9c1de1f92539db77ad0c57e +Author: David Gibson +Date: Mon Dec 17 14:41:52 2007 +1100 - Introduce map_physmem() and unmap_physmem() + libfdt: Add more documentation (patch the sixth) - map_physmem() returns a virtual address which can be used to access a - given physical address without involving the cache. unmap_physmem() - should be called when the virtual address returned by map_physmem() is - no longer needed. + This patch adds some more documenting comments to libfdt.h. + Specifically this documents all the write-in-place functions. - This patch adds a stub implementation which simply returns the - physical address cast to a uchar * for all architectures except AVR32, - which converts the physical address to an uncached virtual mapping. - unmap_physmem() is a no-op on all architectures, but if any - architecture needs to do such mappings through the TLB, this is the - hook where those TLB entries can be invalidated. + Signed-off-by: David Gibson - Signed-off-by: Haavard Skinnemoen +commit b60af3d4c1680487ee37e11aa1b3db6dec04d8f0 +Author: Gerald Van Baren +Date: Sat Dec 29 22:45:27 2007 -0500 -commit cdbaefb5f5f03e54455d0439dcf6dbd97ead1f9d -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:32 2007 +0100 + Fine grained per property /chosen updating. - cfi_flash: Introduce read and write accessors + Implement a suggestion by Scott Wood to make the /chosen handling fine + grained. Don't overwrite pre-existing properties on a per-property basis, + so if /chosen exists but a necessary /chosen/property doesn't, it gets + created. If a /chosen property exists, it is NOT overwritten unless the + "force" flag is true. - Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use - them to access the flash memory. This makes it clearer when the flash - is actually being accessed; merely dereferencing a volatile pointer - looks just like any other kind of access. + Signed-off-by: Gerald Van Baren - Signed-off-by: Haavard Skinnemoen +commit 238cb7a423c6eaa36496efb788cfb9798cea7f95 +Author: Gerald Van Baren +Date: Sat Jan 5 15:33:29 2008 -0500 -commit 812711ce6b3a386125dcf0d6a59588e461abbb87 -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:31 2007 +0100 + Improve the FDT help message. - Implement __raw_{read,write}[bwl] on all architectures + Add a note that "fdt copy" makes the new address active. + Remove most of the extra hints at the end of the fdt help. - This adds implementations of __raw_read[bwl] and __raw_write[bwl] to - m68k, ppc, nios and nios2. The m68k and ppc implementations were taken - from Linux. + Signed-off-by: Gerald Van Baren - Signed-off-by: Haavard Skinnemoen +commit ea6d8be153ceaf16958f8009cea6d75f3ff58d92 +Author: Gerald Van Baren +Date: Sat Jan 5 14:52:04 2008 -0500 -commit be60a9021c82fc5aecd5b2b1fc96f70a9c81bbcd -Author: Haavard Skinnemoen -Date: Sat Oct 6 18:55:36 2007 +0200 + Support setting FDT properties with optional values. - cfi_flash: Reorder functions and eliminate extra prototypes + Fix a bug found and documented by Bartlomiej Sieka where the optional + value on "fdt set []" wasn't optional. - Reorder the functions in cfi_flash.c so that each function only uses - functions that have been defined before it. This allows the static - prototype declarations near the top to be eliminated and might allow - gcc to do a better job inlining functions. + => fdt mknode / testnode + => fdt print /testnode + testnode { + }; + => fdt set /testnode testprop + => fdt print /testnode + testnode { + testprop; + }; - Signed-off-by: Haavard Skinnemoen + Signed-off-by: Gerald Van Baren -commit 3055793bcbdf24b1f8117f606ffb766d32eb766f -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:29 2007 +0100 +commit 22fb2246df91bfc840d87f0c5910818bad55577a +Author: Matthias Fuchs +Date: Fri Dec 28 11:56:30 2007 +0100 - cfi_flash: Make some needlessly global functions static + Add fdt_find_and_setprop() to fdt_support.h - Make functions not declared in any header file static. + fdt_find_and_setprop() is used by several 4xx boards and it's + missing in the appropriate header. This patch eliminates a + warning when building U-Boot for such boards. - Signed-off-by: Haavard Skinnemoen + Signed-off-by: Matthias Fuchs + Acked-by: Stefan Roese -commit 7e5b9b471518c5652febc68ba62b432193d6abf4 -Author: Haavard Skinnemoen -Date: Thu Dec 13 12:56:28 2007 +0100 +commit 802b769bac17b0560d3535a42c502469ee190cd1 +Author: Stefan Roese +Date: Tue Jan 8 18:39:30 2008 +0100 - cfi_flash: Break long lines + ppc4xx: Return 0 on success in 4xx ethernet driver - This patch tries to keep all lines in the cfi_flash driver below 80 - columns. There are a few lines left which don't fit this requirement - because I couldn't find any trivial way to break them (i.e. it would - take some restructuring, which I intend to do in a later patch.) + Signed-off-by: Stefan Roese - Signed-off-by: Haavard Skinnemoen +commit 6775c68683a53c7abc778774641aac6f833a2cbf +Author: Kim Phillips +Date: Tue Jan 8 09:59:49 2008 -0600 -commit 42026c9cb3a76849b41e6e24abfb7b56807a5c1a -Author: Bartlomiej Sieka -Date: Tue Dec 11 13:59:57 2007 +0100 + mpc83xx: fix missed pci_hose -> hose conversion for new libfdt code - CFI: synchronize command offsets with Linux CFI driver + Signed-off-by: Kim Phillips - Fixes non-working CFI Flash on the Inka4x0 board. +commit 94fab25f5f1a7d1c0cc63c17e813ea8943fe49c7 +Author: Kim Phillips +Date: Thu Dec 20 16:28:34 2007 -0600 - Signed-off-by: Bartlomiej Sieka + mpc83xx: rm remaining FLAT_TREE code -commit 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d -Author: Kumar Gala -Date: Fri Dec 7 12:17:34 2007 -0600 + ..in board pci.c files - Handle MPC85xx PCIe reset errata (PCI-Ex 38) + Signed-off-by: Kim Phillips - On the MPC85xx boards that have PCIe enable the PCIe errata fix. - (MPC8544DS, MPC8548CDS, MPC8568MDS). +commit b3458d2cd55d01732e30a76d898afd99e871cd67 +Author: Kim Phillips +Date: Thu Dec 20 15:57:28 2007 -0600 - Signed-off-by: Kumar Gala + mpc83xx: remove FLAT_TREE code -commit 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c -Author: Kumar Gala -Date: Fri Dec 7 12:04:30 2007 -0600 + need to rm it from pci code, too! - Update Freescale MPC85xx ADS/CDS/MDS board config + Signed-off-by: Kim Phillips - * Enabled CONFIG_CMD_ELF +commit 5b8bc606c61456566af6912f818a153b6b06f242 +Author: Kim Phillips +Date: Thu Dec 20 14:09:22 2007 -0600 - Signed-off-by: Kumar Gala + mpc83xx: convert to using do_fixup_*() -commit d435793229ce29a42797c1edc39f5b34f987f91a -Author: Kumar Gala -Date: Fri Dec 7 04:59:26 2007 -0600 + convert to using simpler mpc85xx style fdt update code; streamline by + eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm + the old school FLAT_TREE code from 83xx (since the sbc8349 was just + converted over to using libfdt). - Handle Asynchronous DDR clock on 85xx + Signed-off-by: Kim Phillips - The MPC8572 introduces the concept of an asynchronous DDR clock with - regards to the platform clock. +commit e496865ecc31a2fe2f9abfe798334bb02aaf05ab +Author: Paul Gortmaker +Date: Thu Dec 20 12:58:51 2007 -0500 - Introduce get_ddr_freq() to report the DDR freq regardless of sync/async - mode. + sbc8349: enable libfdt by default on WRS SBC8349 board. - Signed-off-by: Kumar Gala + Make libfdt the default for the WRS SBC8349 board. + Parallel of commit 35cc4e4823668e8745854899cfaedd4489beb0ef + done for the other 83xx based boards. Also fix a typo in CONFIG_PCI. -commit 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10 -Author: Kumar Gala -Date: Thu Nov 29 10:34:28 2007 -0600 + Signed-off-by: Paul Gortmaker - Update Freescale MPC85xx ADS/CDS/MDS board config +commit 2408b3f20bcbdd9c6c397cd03ab0d71d54680a40 +Author: Paul Gortmaker +Date: Thu Dec 20 12:58:16 2007 -0500 - * Removed some misc environment setup - * Enabled CONFIG_CMDLINE_EDITING + sbc8349: migrate board to libfdt - Signed-off-by: Kumar Gala + This adds libfdt support code for the Wind River sbc8349 board. -commit 415a613babb84d5e5d5b42e8e553868c71fc3a64 -Author: Kumar Gala -Date: Thu Nov 29 10:47:44 2007 -0600 + Parallel of commit 3fde9e8b22cfbd7af489214758f9839a206576cb for + the other Freescale 83xx boards. - Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale. + Signed-off-by: Paul Gortmaker - Minor path corrections needed to ensure buildability. +commit 27a256a90cc86392ac9bf0039a3afe638ec2c18d +Author: Paul Gortmaker +Date: Thu Dec 20 12:56:19 2007 -0500 - Signed-off-by: Kumar Gala + sbc8349: Remove board specific ECC code -commit c2d943ffbfd3359b3b45d177b437379d2cb86fbf -Author: Kumar Gala -Date: Thu Nov 29 10:16:18 2007 -0600 + ECC code is now shared for all 83xx boards, so remove board specific one. + See commit daab8c67d2defef73dc26ab07f0c3afd1b05d019 for reference. - Move the MPC8540 ADS board under board/freescale. + Signed-off-by: Paul Gortmaker - Minor path corrections needed to ensure buildability. +commit a1e1ac849249310e5e2e5c7148e9fb353a8317a7 +Author: Kim Phillips +Date: Thu Dec 20 01:30:48 2007 -0600 - Signed-off-by: Kumar Gala + mpc83xx: Remove CONFIG options related to OF that we dont use (on 837x) -commit 870ceac5b3a3486c109396e005af81ae762b5710 -Author: Kumar Gala -Date: Thu Nov 29 10:14:50 2007 -0600 + continuation of commit 37395fa2b0d9d617f28d44ca11592260ef16105a to 837x - Move the MPC8560 ADS board under board/freescale. + Signed-off-by: Kim Phillips - Minor path corrections needed to ensure buildability. +commit ccf21c311e68d48399eff1e72936052885f6e3f7 +Author: Joakim Tjernlund +Date: Thu Dec 6 16:43:40 2007 +0100 - Signed-off-by: Kumar Gala + Add support CONFIG_UEC_ETH3 in MPC83xx -commit acbca876fb3fec25cd9c55b0efc81ff618ff5262 + Signed-off-by: Joakim Tjernlund + +commit e6af9932d31171e35db880e7b2f29f903b1b7660 Author: Kumar Gala -Date: Thu Nov 29 10:13:47 2007 -0600 +Date: Mon Nov 26 11:00:54 2007 -0600 - Move the MPC8568 MDS board under board/freescale. + Remove CONFIG options related to OF that we dont use - Minor path corrections needed to ensure buildability. + The MPC8360E MDS config defined: + CONFIG_OF_HAS_BD_T + CONFIG_OF_HAS_UBOOT_ENV + + Which we don't use or ever needed. This seems like copy-paste feature creep. Signed-off-by: Kumar Gala -commit a853d56c59b33415304531443633808736acfc6e -Author: Kumar Gala -Date: Thu Nov 29 02:18:59 2007 -0600 +commit f602082b4b7ed4ee16432067cc67a0a24fedc715 +Author: Kim Phillips +Date: Mon Dec 10 14:16:22 2007 -0600 - Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx + mpc83xx: supress compiler warning - We already had defines for LAWAR_TRGT_IF_* that we should use - rather than creating new ones. Also, added some missing defines for - PCIE targets. + mpc8360emds.c: In function ‘ft_board_setup’: + mpc8360emds.c:335: warning: assignment discards qualifiers from pointer target type + mpc8360emds.c:345: warning: assignment discards qualifiers from pointer target type - Signed-off-by: Kumar Gala + Signed-off-by: Kim Phillips -commit 04db400892da37b76a585e332a0c137954ad2015 -Author: Kumar Gala -Date: Thu Nov 29 02:10:09 2007 -0600 +commit c16e44fa835fb9eec982d919863a04e2f78e5ce7 +Author: Kim Phillips +Date: Tue Nov 27 14:17:29 2007 -0600 - Stop using immap_t on 85xx + mpc83xx: fix remaining fdt_find_node_by_path references - In the future the offsets to various blocks may not be in same location. - Move to using CFG_MPC85xx_*_ADDR as the base of the registers - instead of getting it via &immap. + rename to fdt_path_offset - Signed-off-by: Kumar Gala + Signed-off-by: Kim Phillips -commit 2714223f8e04ab3e4133ff65872eef366d90bfea -Author: Kumar Gala -Date: Thu Nov 29 01:23:09 2007 -0600 +commit 921d4b19ad1be704df58725485d9292dc0414adf +Author: Kim Phillips +Date: Mon Nov 19 12:30:09 2007 -0600 - Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt + mpc83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions for 837x - Signed-off-by: Kumar Gala + Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x. + This change guarantees that the environment will be located on the + first flash sector after the U-Boot image. -commit c480861bf000156e6a3e932c258db59ff2212dd3 -Author: Kumar Gala -Date: Thu Nov 29 01:06:19 2007 -0600 + Signed-off-by: Kim Phillips - Update MPC8568 MDS to use libfdt +commit 24f868433b50ecbaa88e118aadc7bd254013c6ae +Author: Kim Phillips +Date: Fri Nov 9 14:28:08 2007 -0600 - Updated the MPC8568 MDS config to use libfdt and assume use of aliases for - ethernet, pci, and serial for the various fixups that are done. + mpc83xx: mpc8360 rev.2.1 erratum 2: replace rgmii-id with rgmii-rxid - Signed-off-by: Kumar Gala + u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type + properties in the device tree so the PHY gets configured for internal delay on + RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2. -commit 1563f56e0c68f6920f956382d6d13bee3f01c0f7 -Author: Haiying Wang -Date: Wed Nov 14 15:52:06 2007 -0500 + Signed-off-by: Kim Phillips - Add PCI Express support on MPC8568MDS +commit 22b448dbfbe2a98f01ff4adc3c3979f8c541ad7b +Author: Dave Liu +Date: Tue Sep 18 12:41:15 2007 +0800 - Signed-off-by: Haiying Wang - Signed-off-by: Kumar Gala + mpc83xx: update the CREDITS and MAINTAINERS -commit b90d25497625b90ffa3f2911a0895ca237556ff5 -Author: Kumar Gala -Date: Thu Nov 29 00:11:44 2007 -0600 + update the CREDITS and MAINTAINERS. - Update MPC85xx CDS to use libfdt + Signed-off-by: Dave Liu - Updated the MPC85xx CDS config to use libfdt and assume use of aliases for - ethernet, pci, and serial for the various fixups that are done. +commit b21add4b42af7b767448251b599b91066a160e0d +Author: Dave Liu +Date: Tue Sep 18 12:40:21 2007 +0800 - Signed-off-by: Kumar Gala + mpc83xx: add MAINTAINER and MAKEALL entries for the mpc837xemds -commit 0fd5ec66b10521a057ad73e69ab5f0f9eafba255 -Author: Kumar Gala -Date: Wed Nov 28 22:54:27 2007 -0600 + Add the MAINTAINER and MAKEALL entries for mpc837xemds - Update MPC8540 ADS to use libfdt + Signed-off-by: Dave Liu - Updated the MPC8540 ADS config to use libfdt and assume use of aliases for - ethernet, pci, and serial for the various fixups that are done. +commit f8900ce9094c462355eb792eea264ff16ac8fd16 +Author: Dave Liu +Date: Tue Sep 18 12:38:53 2007 +0800 - Signed-off-by: Kumar Gala + mpc83xx: Add the MPC837xEMDS board readme -commit 5ce715802f6c50dc78b3405b92f184b1e3710519 -Author: Kumar Gala -Date: Wed Nov 28 22:40:31 2007 -0600 + Add the README.mpc837xemds to /doc - Update MPC8560 ADS to use libfdt + Signed-off-by: Dave Liu - Updated the MPC8560 ADS config to use libfdt and assume use of aliases for - ethernet, pci, and serial for the various fixups that are done. +commit 19580e660cc8da49f16536a8bd78c047c7bc12e5 +Author: Dave Liu +Date: Tue Sep 18 12:37:57 2007 +0800 - Signed-off-by: Kumar Gala + mpc83xx: Add the support of MPC837xEMDS board -commit aafeefbdb8b029f5ca2a195598d0a501a606eea9 -Author: Kumar Gala -Date: Wed Nov 28 00:36:33 2007 -0600 + The MPC837xEMDS board support: + * DDR2 400MHz hardcoded and SPD init + * Local bus NOR Flash + * I2C, UART, MII and RTC + * eTSEC RGMII + * PCI host - Stop using immap_t for cpm offset on 85xx + Signed-off-by: Dave Liu - In the future the offsets to various blocks may not be in same location. - Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers - instead of getting it via &immap->im_cpm. +commit 555da61702771fe0f76f3de23b4e7590f3704161 +Author: Dave Liu +Date: Tue Sep 18 12:36:58 2007 +0800 - Signed-off-by: Kumar Gala + mpc83xx: Add the support of MPC8315E SoC -commit f59b55a5b8fcadaa99781ba48e7a38e956afa527 -Author: Kumar Gala -Date: Tue Nov 27 23:25:02 2007 -0600 + The MPC8315E SoC including e300c3 core and new IP blocks, + such as TDM, PCI Express and SATA controller. - Stop using immap_t for guts offset on 85xx + Signed-off-by: Dave Liu - In the future the offsets to various blocks may not be in same location. - Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers - instead of getting it via &immap->im_gur. +commit 03051c3d35c9981ceaa059005660e699f3eacf1c +Author: Dave Liu +Date: Tue Sep 18 12:36:11 2007 +0800 - Signed-off-by: Kumar Gala + mpc83xx: Add the support of MPC837x SoC -commit 50c03c8cf494d91cdec39670d95337c743e16ec9 -Author: Kumar Gala -Date: Tue Nov 27 22:42:34 2007 -0600 + The MPC837x SoC including e300c4 core and new IP blocks, + such as SDHC, PCI Express and SATA controller. - Update MPC8544 DS config + Signed-off-by: Dave Liu - * Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2 - * Removed some misc environment setup - * Moved to using fdtfile & fdtaddr as fdt env var names - * Enabled CONFIG_CMDLINE_EDITING +commit 651d96f7e4c84adcdb98ef07ec878c20326e3359 +Author: Anton Vorontsov +Date: Wed Nov 14 18:54:53 2007 +0300 - Signed-off-by: Kumar Gala + MPC8360E-MDS: configure and enable second UART -commit addce57e2e4c49e77ffb2020a84690713bb18b47 -Author: Kumar Gala -Date: Mon Nov 26 17:12:24 2007 -0600 + Despite user manual, BCSR9.7 is negated (high) on HRST, so + UART2 is disabled. Fix that and configure QE pins properly. - Update MPC8544DS to use libfdt + Signed-off-by: Anton Vorontsov - Updated the MPC8544DS config to use libfdt and assume use of aliases for - ethernet, pci, and serial for the various fixups that are done. +commit b2893e1fcb28fad8c8b317104df8cee0142c7631 +Author: Timur Tabi +Date: Mon Nov 5 09:34:06 2007 -0600 - Signed-off-by: Kumar Gala + 83xx: fix CFG_ENV_ADDR and CFG_ENV_SECT_SIZE definitions -commit f852ce72f100cabd1f11c21c085a0ad8eca9fb65 -Author: Kumar Gala -Date: Thu Nov 29 00:15:30 2007 -0600 + Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the + currently-defined 83xx boards. This change guarantees that the environment + will be located on the first flash sector after the U-Boot image. - Add libfdt based ft_cpu_setup for mpc85xx + Signed-off-by: Timur Tabi + Signed-off-by: Kim Phillips - Signed-off-by: Kumar Gala +commit e05329516a13616b53240cd85b739217c2bf87f1 +Author: Larry Johnson +Date: Fri Jan 4 13:27:02 2008 -0500 -commit 9692c2734a47f23b44a0f68042a3e2ca8d1bfb39 + ppc4xx: Remove weak binding from common Denali data-eye search code + + Now that there are no board-specific versions of + "denali_core_search_data_eye()", the weak binding on the common version + can be removed. + + Signed-off-by: Larry Johnson + +commit 5ba576c01602fd328800a427964c36a0a05c5dce Author: Stefan Roese -Date: Sat Dec 8 08:25:09 2007 +0100 +Date: Sat Jan 5 09:13:46 2008 +0100 - CFI: Coding style cleanup + ppc4xx: Remove unused CONFIG_ECC_ERROR_RESET from 44x_spd_ddr2.c Signed-off-by: Stefan Roese -commit 81b20ccc2d795ae9a1199db5a50ad9c28d1e4d22 -Author: Michael Schwingen -Date: Fri Dec 7 23:35:02 2007 +0100 +commit 845c6c95dbfe6c915ce68a0a115852fa17932fb4 +Author: Stefan Roese +Date: Sat Jan 5 09:12:41 2008 +0100 - CFI: support JEDEC flash roms in CFI-flash framework + ppc4xx: Update Katmai/44x_spd_ddr2.c code for optimal DDR2 setup - The following patch adds support for non-CFI flash ROMS, by hooking into the - CFI flash code and using most of its code, as recently discussed here in the - thread "Mixing CFI and non-CFI flashs". + On Katmai the complete auto-calibration somehow doesn't seem to + produce the best results, meaning optimal values for RQFD/RFFD. + This was discovered by GDA using a high bandwidth scope, + analyzing the DDR2 signals. GDA provided a fixed value for RQFD, + so now on Katmai "only" RFFD is auto-calibrated. + + This patch also adds RDCC calibration as mentioned on page 7 of + the AMCC PowerPC440SP/SPe DDR2 application note: + "DDR1/DDR2 Initialization Sequence and Dynamic Tuning" - Signed-off-by: Michael Schwingen Signed-off-by: Stefan Roese -commit c01b17dd856fa120b2970f50d9598546a4927ec3 -Author: Gerald Van Baren -Date: Wed Nov 28 21:24:50 2007 -0500 +commit 49db47b8ae6afff2b898be312948ff501357dc80 +Author: Matthias Fuchs +Date: Wed Jan 2 16:48:42 2008 +0100 - Conditionally compile fdt_fixup_ethernet() + ppc4xx: Remove sdram.h from PMC440 board - Fix compiler warnings: On boards that don't have ethernets defined, - don't compile fdt_fixup_ethernet(). + Signed-off-by: Matthias Fuchs -commit 246d4ae6bc282bc1841224e1c5fc49dc925e0bf7 -Author: Kumar Gala -Date: Tue Nov 27 21:59:46 2007 -0600 +commit 34065a2ce0d8972f2ec6652076014ab243d2ce8a +Author: Matthias Fuchs +Date: Wed Jan 2 16:48:34 2008 +0100 - Convert boards that set memory node to use fdt_fixup_memory() + ppc4xx: use common denali core defines and data eye search code for PMC440 - Signed-off-by: Kumar Gala + Signed-off-by: Matthias Fuchs -commit 151c8b09b35eebe8fd9139cb6c1d91c27b22f058 -Author: Kumar Gala -Date: Mon Nov 26 17:06:15 2007 -0600 +commit 9ac6b6f3d3f1b072d89268b2efe47e95e6659489 +Author: Matthias Fuchs +Date: Wed Jan 2 12:05:14 2008 +0100 - Added fdt_fixup_stdout that uses aliases to set linux,stdout-path + ppc4xx: More cleanup for esd's LCD code - We use a combination of the serialN alias and CONFIG_CONS_INDEX to - determine which serial alias we should set linux,stdout-path to. + Signed-off-by: Matthias Fuchs - Signed-off-by: Kumar Gala +commit fe9c26b330a21ce73e52b5bd347d725cb81e3cfb +Author: Stefan Roese +Date: Fri Jan 4 12:00:01 2008 +0100 -commit 3c9272813fad84c691d0e4989bb18a3ffebdebfc -Author: Kumar Gala -Date: Mon Nov 26 14:57:45 2007 -0600 + ppc4xx: Fix Sequoia NAND booting target - Add common memory fixup function + The Sequoia NAND booting target now uses the recently extracted + cpu/ppc4xx/denali_data_eye.c file too. - Add the function fdt_fixup_memory() to fixup the /memory node of the fdt + Signed-off-by: Stefan Roese - Signed-off-by: Kumar Gala +commit 0ddd969aec532bd7eae30fc09590488a3aaa629a +Author: Lawrence R. Johnson +Date: Thu Jan 3 15:02:02 2008 -0500 -commit 9c9109e7fcf7ac2ca19c95b8ac54b8d1c773b157 -Author: Kumar Gala -Date: Mon Nov 26 11:19:12 2007 -0600 + ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Korat board - Conditionally compile fdt_support.c + Signed-off-by: Larry Johnson - Modify common/Makefile to conditionally compile fdt_support.c based - on CONFIG_OF_LIBFDT. +commit b05e8bf58be9d8956fdfde3d8c8e87c140414663 +Author: Lawrence R. Johnson +Date: Fri Jan 4 02:11:56 2008 -0500 - Signed-off-by: Kumar Gala + ppc4xx: Use CFG_4xx_GPIO_TABLE to configure Sequoia board -commit d88e7ba0980773479e1a64badb293116071b7ef0 -Author: Kumar Gala -Date: Mon Nov 26 10:41:40 2007 -0600 + Note: this patch changes the configuration of some GPIO registers: - Fix build breakage due to libfdt import + Register Old Value New Value + --------------- ---------- ---------- + DCR GPIO0_TCR 0x0000000F 0x0000F0CF + DCR GPIO0_TSRH 0x55005000 0x00000000 + DCR GPIO1_TCR 0xC2000000 0xE2000000 + DCR GPIO1_TSRL 0x0C000000 0x00200000 + DCR GPIO1_ISR2L 0x00050000 0x00110000 - The IDS8247 got lost in the update and need an API update - do to rename of functions in libfdt. + Signed-off-by: Larry Johnson - Signed-off-by: Kumar Gala +commit 5ab884b254ca2e707ab50545cd705f30108cf491 +Author: Lawrence R. Johnson +Date: Thu Jan 3 18:54:00 2008 -0500 + + ppc4xx: Add functionality to GPIO support + + This patch makes two additions to GPIO support: + + First, it adds function gpio_read_in_bit() to read the a bit from the + GPIO Input Register (GPIOx_IR) in the same way that function + gpio_read_out_bit() reads a bit from the GPIO Output Register + (GPIOx_OR). + + Second, it modifies function gpio_set_chip_configuration() to provide + an additional option for configuring the GPIO from the + "CFG_4xx_GPIO_TABLE". + + According to the 440EPx User's Manual, when an alternate output is used, + the three-state control is configured in one of two ways, depending on + the particular output. The first option is to select the corresponding + alternate three-state control in the GPIOx_TRSH/L registers. The second + option is to select the GPIO Three-State Control Register (GPIOx_TCR) in + the GPIOx_TRSH/L registers, and set the corresponding bit in the + GPIOx_TCR register to enable the output. For example, the Manual + specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use + the alternate three-state control (first option), and specifies + configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output + enabled in the GPIOx_TCR register (second option). + + Currently, gpio_set_chip_configuration() configures all alternate signal + outputs to use the first option. This patch allow the second option to + be selected by setting the "out_val" element in the table entry to + "GPIO_OUT_1". The first option is used when the "out_val" element is + set to "GPIO_OUT_0". Because "out_val" is not currently used when an + alternate signal is selected, and because all current GPIO tables set + "out_val" to "GPIO_OUT_0" for all alternate signals, this patch should + not change any existing configurations. -commit 28f384b171bbf1fb2dafb1046e6d259a6b2f8714 -Author: Gerald Van Baren -Date: Fri Nov 23 19:43:20 2007 -0500 + Signed-off-by: Larry Johnson - Add spaces around the = in the fdt print format. +commit 196404cdc1de495d6182e84731c200fc5748df15 +Author: Larry Johnson +Date: Sun Dec 30 01:01:54 2007 -0500 - Signed-off-by: Gerald Van Baren + PPC4xx: Remove sdram.h from board/lwmon5 -commit 29592ecba3b932b9b152bcec6c0c0806412db4a3 -Author: Nobuhiro Iwamatsu -Date: Fri Dec 7 01:25:38 2007 +0900 + These definitions are now in "include/ppc440.h". - sh: Moved driver of the SuperH dependence + Signed-off-by: Larry Johnson - The composition of the directory in the drivers/ changed. - I moved SuperH serial driver and marubun PCMCIA driver. +commit ef16fccf96e55eab93fe25d03ebe2e9b56e5332b +Author: Larry Johnson +Date: Sun Dec 30 01:01:32 2007 -0500 - Signed-off-by: Nobuhiro Iwamatsu + PPC4xx: Use common code for LWMON5 board SDRAM support -commit 41be969f4957115ed7b1fe8b890bfaee99d7a7a2 -Author: Wolfgang Denk -Date: Thu Dec 6 10:21:19 2007 +0100 + This patch also modifies the functionality of the code so that the data-eye + search is now done with with the cache disabled. - Release v1.3.1 + Signed-off-by: Larry Johnson - Signed-off-by: Wolfgang Denk +commit 62cc3951ab72135d9c101f1845b794e63a0fa189 +Author: Larry Johnson +Date: Sun Dec 30 01:01:14 2007 -0500 -commit cf5933ba1e97a1cd8f5f24070e820f21d976eaeb -Author: Wolfgang Denk -Date: Thu Dec 6 10:21:03 2007 +0100 + PPC4xx: Remove sdram.h from board/amcc/sequoia - ADS5121 Board: fix compile problem. + These definitions are now in "include/ppc440.h". - Signed-off-by: Wolfgang Denk + Signed-off-by: Larry Johnson -commit 8d4f040a3c15036a6ea25a9c39e7d89fefa8440d -Author: Wolfgang Denk -Date: Mon Dec 3 00:15:28 2007 +0100 +commit ce3902e1765bbfb07cf5bbe98be9a68e3009996a +Author: Larry Johnson +Date: Sun Dec 30 01:00:50 2007 -0500 - Prepare for 1.3.1-rc1 + PPC4xx: Use common code for Sequoia board SDRAM support - Signed-off-by: Wolfgang Denk + Signed-off-by: Larry Johnson -commit 260eea5676ca46903a335686cc020b29c4ca46fe -Author: Nobuhiro Iwamatsu -Date: Thu Nov 29 01:21:54 2007 +0900 +commit 8b0c5c127690335758100c25eaec2b84db97c101 +Author: Matthias Fuchs +Date: Thu Dec 27 16:58:41 2007 +0100 - sh: Add SuperH boards maintainer to MAINTAINERS file + net: Add CONFIG_NET_DO_NOT_TRY_ANOTHER option - Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file. + When CONFIG_NET_DO_NOT_TRY_ANOTHER is defined U-Boot's + networking stack does not automatically switch to + another interface. This patch does not touch the default + behavior. - Signed-off-by: Nobuhiro Iwamatsu + Signed-off-by: Matthias Fuchs + Signed-off-by: Ben Warren -commit aa9c4f1d22701a92347c1c81f34d12c8ad3a3747 -Author: Nobuhiro Iwamatsu -Date: Thu Nov 29 00:13:04 2007 +0900 +commit 505be87a65e4f87ad7d8da1d57ea4dcd487d7e32 +Author: Upakul Barkakaty +Date: Thu Nov 29 12:16:13 2007 +0530 - sh: Add ms7750se support in MAKEALL + NET: Proper return code handling in eth_init() function in file eth.c - Signed-off-by: Nobuhiro Iwamatsu + This patch modifies the return code handling in the eth_init() + function, to be compatible with the handling of the return codes in + the other network stack files. It now returns a 0 on Success and -1 on + error. -commit c7144373427a178332bf9754131c8c34c52c200a -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 27 09:44:53 2007 +0100 + Signed-off-by: Upakul Barkakaty + Signed-off-by: Ben Warren - sh: Add sh3 and sh4 support in MAKEALL +commit 5ca2d0953e4579a80810966cca2077e20d912c97 +Author: Shinya Kuribayashi +Date: Mon Nov 19 20:27:04 2007 +0900 - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD - Signed-off-by: Nobuhiro Iwamatsu + net/eth.c: Fix env_enetaddr signed overflow -commit 130080874a3d28450098481a262c5f7c855e908d -Author: Nobuhiro Iwamatsu -Date: Sun Nov 25 02:51:17 2007 +0900 + Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are + warned as below: - sh: Add document for SuperH. + U-Boot 1.2.0 (Aug 30 2007 - 08:27:37) - This document is a summary of information concerning SuperH of U-Boot. + DRAM: 256 MB + Flash: 32 MB + In: serial + Out: serial + Err: serial + Net: NEC-Candy + Warning: NEC-Candy MAC addresses don't match: + Address in SROM is 00:00:4C:80:92:A2 + Address in environment is FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21 - Signed-off-by: Nobuhiro Iwamatsu + This patch changes env_enetaddr type from `char' to `unsigned char'. -commit 33ecdc2f9d64926e1a6067b28f3a0aefc3b6d23d -Author: Nobuhiro Iwamatsu -Date: Sun Nov 25 02:39:31 2007 +0900 + Cc: Masaki Ishikawa + Signed-off-by: Shinya Kuribayashi + Signed-off-by: Ben Warren - sh: Add marubun's pcmcia driver +commit f85b60710571b37293d2233933b76e2aa3db5635 +Author: Rafal Jaworowski +Date: Thu Dec 27 18:19:02 2007 +0100 - Marubun pcmcia is a chip for PCMCIA used with SuperH. - Of course, this can be used even by other architectures. - When use this driver, came to be able to use CompactFlash - and Ethernet. + Introduce new eth_receive routine - Signed-off-by: Nobuhiro Iwamatsu + The purpose of this routine is receiving a single network frame, outside of + U-Boot's NetLoop(). Exporting it to standalone programs that run on top of + U-Boot will let them utilise networking facilities. For sending a raw frame + the already existing eth_send() can be used. -commit febd86b969b975289ed948f1ac0eb9722da41ced -Author: Nobuhiro Iwamatsu -Date: Sun Nov 25 02:32:13 2007 +0900 + The direct consumer of this routine is the newly introduced API layer for + external applications (enabled with CONFIG_API). - sh: Update SuperH SCIF driver + Signed-off-by: Rafal Jaworowski + Signed-off-by: Piotr Kruszynski + Signed-off-by: Ben Warren - - Changed volatile unsigned to vu_. - - Changed Makefile for kconfig. +commit 5c740711f0ea5b51414b341b71597c4a0751be74 +Author: Jon Loeliger +Date: Thu Jan 3 10:41:04 2008 -0600 - Signed-off-by: Nobuhiro Iwamatsu + 8610: Move include of config.h earlier. -commit a5f601fd1b1278deae5aa9fc27a232b0d1c1c788 -Author: Wolfgang Denk -Date: Mon Nov 26 19:18:21 2007 +0100 + Include config.h earlier in the set of #includes + so as to avoid a incidental and duplicate definition + of CFG_CACHELINE_SIZE. - Cleanup coding style; update CHANGELOG + Signed-off-by: Jon Loeliger - Signed-off-by: Wolfgang Denk +commit 61d3421bdea090bd0399b14c3e10a3bebcc8d5ff +Author: Jon Loeliger +Date: Tue Dec 4 10:53:34 2007 -0600 -commit 3deca9d44767efd1b83f4b701f0dbf21a7595f7b -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sun Nov 25 22:39:25 2007 +0100 + Don't slam #undef DEBUG in the 8641HPCN config file. - MAKEALL: add missing 512x boards in ppc + Doing so prevents it from being individually set + and useful in other files. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Jon Loeliger -commit a340c325e668ca7386c2276387681720be9c3757 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sun Nov 25 18:45:47 2007 +0100 +commit ea9f7395ec362584e5e4f266bd0b0c4422cf6a4c +Author: Jon Loeliger +Date: Wed Nov 28 14:47:18 2007 -0600 - Makefile : fix tags ctags etags with new drivers organization + Convert MPC8641HPCN to use libfdt. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Assumes the presence of the aliases node in the DTS to + locate the ethernet, pci and serial nodes for fixups. -commit 87ddedd6ad804427ce125ceaa076d7a4f74e9d5d -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sun Nov 25 18:45:47 2007 +0100 + Use consistent fdtaddr and fdtfile in environment variables. - Makefile : fix tags ctags etags with new drivers organization + Signed-off-by: Jon Loeliger - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD +commit ce37422d0002e10490e268392e0c4e3028e52cec +Author: Stefan Roese +Date: Wed Jan 2 14:06:26 2008 +0100 -commit 59829cc189378c142c13d2aa8d9a897d8bef3961 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 21:26:56 2007 +0100 + cfi_flash: Fix bug in flash_isset() to use correct 32bit function - drivers/mtd : move mtd drivers to drivers/mtd + This bug was detected on the LWMON5 target which has 2 Intel 16bit wide + flash chips connected to a 32bit wide port. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Stefan Roese -commit 318c0b90431f2648552e5ade78833f42652ce859 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 21:17:55 2007 +0100 +commit 1182e9f8e3b92fc372d64943293de53daa2e26cf +Author: Wolfgang Denk +Date: Wed Jan 2 15:58:44 2008 +0100 - drivers/misc : move misc drivers to drivers/misc + Fix compile problem introduced by "cleanup" commit 3dfd708c - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Wolfgang Denk -commit 33daf5b7858807cb4ce4158c2c56524671c14c08 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 21:13:59 2007 +0100 +commit 1aaab9bfae0b3b2ee2b418c22c651280ee7b65c7 +Author: Wolfgang Denk +Date: Wed Jan 2 15:54:45 2008 +0100 - drivers/block : move block drivers to drivers/block + Make scripts and Makefiles POSIX compliant - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + The bash builtin versions of the "test" (resp. "[") command allow + using "==" for string comparisons, but POSIX compatible implemen- + tations (like /usr/bin/test) insist on using "=" only. On such systems + you will see: -commit 0c698dcaa70275eb8814f665b545547cee013892 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 20:59:50 2007 +0100 + $ /usr/bin/test a == a && echo OK + /usr/bin/test: ==: binary operator expected - drivers/rtc : move rtc drivers to drivers/rtc + This patch fixes Makefiles and scripts to use POSIX style. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Wolfgang Denk -commit f868cc5a50757d94f36c312395481cb0f187d9e6 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 20:14:44 2007 +0100 +commit 3dfd708cc1b2a966ad454ca9ed125dd17dbadbcc +Author: Wolfgang Denk +Date: Wed Jan 2 12:38:43 2008 +0100 - drivers/hwmon : move hardware monitor drviers to drivers/hwmon + Minor coding style cleanup. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Wolfgang Denk -commit 16b195c82a18cbfd164800f17a1ef9db2e48331a -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 19:46:45 2007 +0100 +commit e174ac34adf5d5653df12bc3cf19c52063a71269 +Author: Stefan Roese +Date: Fri Dec 28 17:29:56 2007 +0100 - drivers/input : move input drivers to drivers/input + ppc4xx: Coding style cleanup - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Stefan Roese -commit e4558666293364fc3af1c1d9381ca933fa0f1275 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 19:40:11 2007 +0100 +commit 8ba132cab18ae438b6dd5b0214c28a8fc0d976e5 +Author: Matthias Fuchs +Date: Fri Dec 28 17:07:24 2007 +0100 - drivers/usb : move usb drivers to drivers/usb + ppc4xx: Complete PMC440 board support - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + This patch brings the PMC440 board configuration file. + Finally it enables the PMC440 board support. -commit 1378df792a7ff3abd1bf54a63f5475784f5b083c -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 24 19:33:38 2007 +0100 + Signed-off-by: Matthias Fuchs - drivers/serial : move serial drivers to drivers/serial +commit 407843a582560fc5231299561ab3c2b6b6cd3397 +Author: Matthias Fuchs +Date: Fri Dec 28 17:07:18 2007 +0100 - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + ppc4xx: Add FPGA support and BSP commands for PMC440 boards -commit 2439e4bfa111babf4bc07ba20efbf3e36036813e -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Wed Nov 21 21:19:24 2007 +0100 + This patch adds some BSP commands and FPGA booting support + for esd's PMC440 boards. - drivers/net : move net drivers to drivers/net + Signed-off-by: Matthias Fuchs - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD +commit 72c5d52aedcce35e4b4fa5895605554825b6a76f +Author: Matthias Fuchs +Date: Fri Dec 28 17:07:14 2007 +0100 -commit 352d259130b349fe9593b8dada641bd78a9659e5 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 20 20:41:48 2007 +0100 + ppc4xx: Add initial esd PMC440 board files - drivers/video : move video drivers to drivers/video + This patch adds the first files for the new esd PMC440 boards. + The next two patches will complete the PMC440 board support. - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Matthias Fuchs -commit 73646217186aa17afc8e305c5f06f06dd335eaad -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 20 20:33:09 2007 +0100 +commit f6e0f1f61896ce7729ba1bcea2ffbd138d3947f5 +Author: Matthias Fuchs +Date: Fri Dec 28 17:10:36 2007 +0100 - drivers/pcmcia : move pcmcia drivers to drivers/pcmcia + ppc4xx: Add EEPROM write protection for PLU405 boards + misc. updates - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + - add EEPROM write protection for esd PLU405 boards. + - initialize NAND GPIOs + - use correct io accessors + - cleanup -commit 93a686ee9c5ddc6fa368c32cfbfde6f6724599fc -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 20 20:28:09 2007 +0100 + Signed-off-by: Matthias Fuchs - drivers/pci : move pci drivers to drivers/pci +commit 77660c4b59055d621d2a8595bd4c18bb277268fc +Author: Matthias Fuchs +Date: Fri Dec 28 17:10:44 2007 +0100 - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + ppc4xx: use correct io accessors for esd's LCD code -commit 9162352817579840d7802da6d85872b3ca003c97 -Author: Gerald Van Baren -Date: Thu Nov 22 17:23:23 2007 -0500 + This patch fixes esd's LCD dectection code to work correctly with + newer gcc versions. - Fix fdt printing for updated libfdt + Signed-off-by: Matthias Fuchs - Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup. +commit b56bd0fcfc1c73db722e3462c8a9bf607ba7775e +Author: Matthias Fuchs +Date: Fri Dec 28 17:10:42 2007 +0100 - Signed-off-by: Gerald Van Baren + ppc4xx: Maintenance patch for VOH405 boards -commit 9eb77cea1fa12d5969eb26a1d1d81da381bd6b1c -Author: Kumar Gala -Date: Wed Nov 21 13:30:15 2007 -0600 + - add EEPROM write protection + - initialize NAND GPIOs + - use correct io accessors + - slow down I2C clock to 100kHz + - enable ext. I2C bus + - cleanup - Add additional fdt fixup helper functions + Signed-off-by: Matthias Fuchs - Added the following fdt fixup helpers: - * do_fixup_by_prop{_u32} - Find matching nodes by property name/value - * do_fixup_by_compat{_u32} - Find matching nodes by compat +commit c05569066dbcba3fdf36d4d1943df265dc316a86 +Author: Stefan Roese +Date: Fri Dec 28 16:08:08 2007 +0100 - The _u32 variants work the same only the property they are setting - is know to be a 32-bit integer instead of a byte buffer. + ppc4xx: Enable 405EP PCI arbiter per default on all boards - Signed-off-by: Kumar Gala + In an attmemt to clean up the 4xx start.S file, I removed the enabling + of the internal 405EP PCI arbiter. This is needed for multiple other + 405EP platforms, like most of the esd 405EP. Now the internal PCI + arbiter is enabled again per default as it has been before. -commit ab544633abdd14f4dd5d92e500b73eb59ef57e67 -Author: Kumar Gala -Date: Wed Nov 21 11:11:03 2007 -0600 + Signed-off-by: Stefan Roese + Acked-by: Matthias Fuchs - Add fdt_fixup_ethernet helper to set mac addresses +commit bec9264616fb78273a1d93e87ff4b0b67c7bec1b +Author: Stefan Roese +Date: Fri Dec 28 15:53:46 2007 +0100 - Added a fixup helper that uses aliases to set mac addresses - in the device tree based on the bd_t + ppc4xx: Fix bug in cpu_init.c (405EP instead of 450EP) - Signed-off-by: Kumar Gala + Signed-off-by: Stefan Roese + Acked-by: Matthias Fuchs -commit dbaf07ce620aab249e3502b20a986234a6af1d3a -Author: Kumar Gala -Date: Wed Nov 21 14:07:46 2007 -0600 +commit fb83a65c60ab5ca12358b75f1257e5eee6cdbf79 +Author: Stefan Roese +Date: Fri Dec 28 06:06:04 2007 +0100 - Fix warnings from import of libfdt + ppc4xx: Fix compilation problem of kilauea/haleakala nand booting target - cmd_fdt.c: In function fdt_print: - cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type - cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type - cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type - cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type + Use correct link to nand_ecc now located in drivers/mtd/nand/ for the + platforms mentioned above. - Signed-off-by: Kumar Gala + Signed-off-by: Stefan Roese -commit 8d04f02f6224e6983f4812ea4da704950ec8539c -Author: Kumar Gala -Date: Wed Oct 24 11:04:22 2007 -0500 +commit b568fd25574181a3b12ae3d66b2913903442cb83 +Author: Matthias Fuchs +Date: Thu Dec 27 17:03:46 2007 +0100 - Update libfdt from device tree compiler (dtc) + Remove CPCI440 board - Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from - the device tree compiler (dtc) project. + This board never left prototyping state and it + became a millstone round my neck. So remove it. - Signed-off-by: Kumar Gala + Signed-off-by: Matthias Fuchs -commit e93becf80d732b64aef81b23e8b6ece02c40533d -Author: Kumar Gala -Date: Sat Nov 3 19:46:28 2007 -0500 +commit c591dffe0cbacd896ccbad06011fe6d6afa080da +Author: Larry Johnson +Date: Thu Dec 27 11:28:51 2007 -0500 - Move do_fixup* for libfdt into common code + Add support for Korat PPC440EPx board - Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260 - into common/fdt_support.c and renamed: + These patches add support for the PPC440EPx-based "Korat" board to + U-Boot. They are based primarily on support for the Sequoia board. - do_fixup() -> do_fixup_by_path() - do_fixup_u32() -> do_fixup_by_path_u32() + Signed-off-by: Larry Johnson - Signed-off-by: Kumar Gala +commit 87dc096829e6a6363f4fdd73653b0093a85adbe0 +Author: Larry Johnson +Date: Sat Dec 22 15:16:25 2007 -0500 -commit f738b4a75998f42a7408defadc9baac7a31c92db -Author: Kumar Gala -Date: Thu Oct 25 16:15:07 2007 -0500 + Add configuration file for Korat board - Make no options to fdt print default to '/' + This patch supplies the configuration file for the Korat PPC440EPx- + processor board. - Signed-off-by: Kumar Gala + Signed-off-by: Larry Johnson -commit a3c2933e02503fe36ade2c1b65af46f2b7a168e7 -Author: Kumar Gala -Date: Wed Oct 24 10:21:57 2007 -0500 +commit 8eb52d5d982b764b39c88d9d1064d56c5397bfa5 +Author: Larry Johnson +Date: Sat Dec 22 15:16:11 2007 -0500 - Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt + Add denali_data_eye.o and denali_spd_ddr2.o to PPC4xx Makefile - Removed: - fdt_node_is_compatible - fdt_find_node_by_type - fdt_find_compatible_node + Signed-off-by: Larry Johnson - To ease merge of newer libfdt as we aren't using them anywhere at this time. +commit aba19604d848b2838cfb9ebe818909e6a216058e +Author: Larry Johnson +Date: Thu Dec 27 10:54:48 2007 -0500 - Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same - reason. + Add 440EPx DDR2 SPD DIMM support - Signed-off-by: Kumar Gala + This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM + controller. It should also work on the 440GRx. It is based on the DDR2 + SPD code for the 440EP/440EPx, but makes no provision for DDR1 support. -commit 98e2867cc85409b919f862e6c16026461ec955df -Author: Grant Likely -Date: Wed Nov 21 09:19:37 2007 -0700 + This code has been tested on prototype Korat boards with three Kingston + DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC + (two ranks). The Korat board has a single DIMM socket, but support has + been provided (though not tested) for boards with two DIMM sockets. - [BUILD] Remove libraries when updating autoconf.mk + Signed-off-by: Larry Johnson - Fix library problems caused by conditional compilation. Using - autoconf.mk to decide which files to compile has caused a problem when - changing configuration from one board to another without clearing out - the library (*.a) files. +commit 8a24a6963002cb867d5a6b70e3560f0b1467f55f +Author: Larry Johnson +Date: Sat Dec 22 15:15:30 2007 -0500 - It used to be that the linker was always passed the same list of .o - files when building the .a files. However, that is not longer true - with conditional compilation. Now, a different board config will have - a different file list passed to the linker. The problem occurs when - a library has already been built and the board config is changed. + Copy 440EPx/GRx SDRAM data-eye search to common directory - Since the linker will update instead of replace a preexisting library, - then if the file list changes to remove some object files the old - objects will still exist in the library. + This patch creates a non-board-specific file for performing the SDRAM + data-eye search. It also adds ECC error checking to the test of valid + data on readback when ECC is enabled. - The solution is to remove all old library files when autoconf.mk is - made. + Signed-off-by: Larry Johnson - Signed-off-by: Grant Likely +commit c46f53333b22b1f9098676bea8884fc7db820cf3 +Author: Larry Johnson +Date: Sat Dec 22 15:15:13 2007 -0500 -commit ed1353d74b9ce8a7fcd660570b848a184d614b5f -Author: Kumar Gala -Date: Wed Nov 21 08:49:50 2007 -0600 + Add definitions for 440EPx/GRx SDRAM controller to ppc440.h - [BUILD] conditionally compile libfdt/*.c in libfdt/Makefile + This patch adds the Denali SDRAM controller definitions to "ppc440.h". + It also fixes two typos in the definitions, so the board-specific + "sdram.h" files containing these definitions are also fixed to avoid + compiler warnings. - Modify libfdt/Makefile to conditionally compile the *.c files based - on the board config. + Signed-off-by: Larry Johnson + +commit c348578bf612d0c56d8d376d23cae16defbd86af +Author: Larry Johnson +Date: Thu Dec 27 10:50:55 2007 -0500 + + Add Ethernet 1000BASE-X support for PPC4xx + + This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol + is defined, the PHY will advertise it's capabilities for autonegotiation + based on the capabilities shown in the PHY's status registers, including + 1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will + advertise hard-coded capabilities, as before. + + Signed-off-by: Larry Johnson + +commit 9e2c347151db5ae8acf5f18b99493cd53e6637e3 +Author: Larry Johnson +Date: Thu Dec 27 09:52:17 2007 -0500 + + Add driver for National Semiconductor LM73 temperature sensor + + This driver is based on the driver for the LM75. + + Signed-off-by: Larry Johnson + +commit 12618278688ea9b3d76536960a5ad2e3790fac40 +Author: Larry Johnson +Date: Sat Dec 22 15:14:00 2007 -0500 + + Add driver for STMicroelectronics M41T60 RTC + + This driver is based on the driver for the M41T11. In the intended + application, the RTC will be powered by a large capacitor, rather than a + battery. The driver therefore checks to see whether the RTC has lost + power. The chip's OUT bit is normally reset from its power-up state. If + the OUT bit is read as set, or if the date and time are not valid, then the + RTC is assumed to have lost power, and its date and time are reset to + 1900-01-01 00:00:00. + + Support for adjusting the speed of the clock to improve accuracy is + provided through an environment variable. + + Signed-off-by: Larry Johnson + +commit d3471173e14b7544bb60339eda8d3d3906694b0a +Author: Larry Johnson +Date: Sat Dec 22 15:34:39 2007 -0500 + + Use out_be32() and friends to access memory-mapped registers in sequoia.c + + Signed-off-by: Larry Johnson + +commit c68f59fe3ec16769f82b5fca7421983c336d3aac +Author: Larry Johnson +Date: Sat Dec 22 15:34:20 2007 -0500 + + Use definitions from "asm-ppc/mmu.h" in init.S for Sequoia + + Signed-off-by: Larry Johnson + +commit 0d9cdeac1d3fa8d62ed7d883acc950c364f5bda8 +Author: Larry Johnson +Date: Sat Dec 22 15:23:50 2007 -0500 + + Cosmetic changes to ECC POST for AMCC Denali core + + Signed-off-by: Larry Johnson + +commit 2e583d6c81034f80a267b89fa55498ae063ccef1 +Author: Stefan Roese +Date: Wed Dec 26 20:20:19 2007 +0100 + + ppc4xx: Fix compilation problem in 405 cache POST test + + Signed-off-by: Stefan Roese + +commit 42d55ea0bde06e47d5a3b49b0d91002acd8e5708 +Author: Stefan Roese +Date: Sat Dec 22 12:20:09 2007 +0100 + + ppc4xx: Move virtual address of POST cache test to bigger address + + On Sequoia & LWMON5 the virtual address of the POST cache test is now + moved to a bigger address. This enables usage of more memory on those + boards. + + Signed-off-by: Stefan Roese + +commit d91722102cf63f77a0148ed3f3d54a26d87575e9 +Author: Stefan Roese +Date: Sat Dec 22 12:18:26 2007 +0100 + + ppc4xx: Fix problem in 44x cache POST routine + + As repoted by Larry Johnson, running "diag run cache" caused a crash + in U-Boot. This problem was introduced by a patch that removed the + TLB entry for the cache test after the test has completed. Since this + TLB was only setup once, a 2nd attempt to run this cache test + failed with a crash. Now this TLB entry is created every time the + routine is called. + + Signed-off-by: Stefan Roese + +commit b0265b576bb8fa9465f99e99c323768b562fadc2 +Author: Stefan Roese +Date: Fri Dec 21 07:51:29 2007 +0100 + + ppc4xx: Update Makalu fdt support + + Signed-off-by: Stefan Roese + +commit bf8324e4a50758daff8cddd04c6a2ff8ed775bea +Author: Stefan Roese +Date: Wed Dec 19 09:05:40 2007 +0100 + + ppc4xx: Add fdt support to AMCC Katmai eval board + + Signed-off-by: Stefan Roese + +commit 328a340392a5df9aaf00792be989df73e750859e +Author: Stefan Roese +Date: Tue Dec 18 08:44:51 2007 +0100 + + ppc4xx: fdt: Cleanup setup of cpu node setup + + Now the cpu node setup ("timebase-frequency" and "clock-frequency") is + without using the absolute path to the cpu node. This makes it possible + to use this U-Boot version with both versions of cpu-node naming + "cpu@0" and the former "PowerPC,440EPx@0". + + Signed-off-by: Stefan Roese + +commit 7812bc4a2e2436ebbc0ce5b4e99c1dfc2e77eb5b +Author: Stefan Roese +Date: Mon Dec 17 17:26:21 2007 +0100 + + ppc4xx: Fix lwmon5 compilation problem + + Now that the 440EPx ECC test is not board specific anymore + remove this Makefile. + + Signed-off-by: Stefan Roese + +commit 42ed33ffe135f618680f9d6e9712eb35a85bcb62 +Author: Anatolij Gustschin +Date: Wed Dec 5 17:43:20 2007 +0100 + + Fix ppc4xx clear_bss() code + + ppc4xx clear_bss() fails if BSS segment size is not + divisible by 4 without remainder. This patch provides + fix for this problem. + + Signed-off-by: Anatolij Gustschin + +commit 85dc2a7f82d11e17f0ca2a448118aed7f7a4b85d +Author: Niklaus Giger +Date: Fri Nov 30 18:35:11 2007 +0100 + + PPC4xx: Minimal changes to add vxWorks support + + Signed-off-by: Niklaus Giger + +commit 052440b022ca8981d39b6f8c10d1aa6326f47480 +Author: Markus Klotzbücher +Date: Fri Nov 23 13:09:18 2007 +0100 + + ppc4xx: Add CONFIG_BOOTP_SUBNETMASK to Sequoia board config + + When using dhcp/bootp the "netmask" environment variable is not + set because CONFIG_BOOTP_SUBNETMASK is not defined. But usually this is + desireable, so the following patch adds this this option to the board + config. + + Signed-off-by: Markus Klotzbuecher + Signed-off-by: Stefan Roese + +commit a724a9b40c7fbeb6ade193ca52321b441eaecb4e +Author: Larry Johnson +Date: Sat Oct 27 12:48:15 2007 -0400 + + Fix/enhance ECC POST for 440EPx/GRx + + This patch allows the ECC POST to be used for different boards with the + PPC440 Denali SDRAM controller. Modifications include skipping the test + if ECC is not enabled (as for non-ECC DIMMs) and adding synchronization + to prevent timing errors. + + Signed-off-by: Larry Johnson + +commit 454a6cf8d498f70d2b3e18f07837603eb24b12d4 +Author: Larry Johnson +Date: Sat Oct 27 12:48:05 2007 -0400 + + PPC4xx: Move/rename ECC POST for 440EPx/GRx + + Signed-off-by: Larry Johnson + +commit c29d2d3680046d430022c55e50fcb27f5866517e +Author: Matthias Fuchs +Date: Fri Dec 14 11:20:33 2007 +0100 + + ppc4xx: use correct io accessors for 4xx ethernet POST + + Signed-off-by: Matthias Fuchs + +commit ba79fde58a48c0a6ff8e2a96caba951594142203 +Author: Matthias Fuchs +Date: Fri Dec 14 11:19:56 2007 +0100 + + ppc4xx: fix flush + invalidate_dcache_range arguments + + flush + invalidate_dcache_range() expect the start and stop+1 address. + So the stop address is the first address behind (!) the range. + + Signed-off-by: Matthias Fuchs + +commit 871e6ce188a7c6bc7321bcf8372857035d20f1cd +Author: Stefan Roese +Date: Fri Dec 14 08:41:29 2007 +0100 + + ppc4xx: fdt: use fdt_fixup_ethernet() + + By using aliases in the dts file, the ethernet node fixup is + much easier with the recently added functions. + + Please note that the dts file needs the aliases for this to work. + + Signed-off-by: Stefan Roese + +commit 136288847e3b04f2ff357a067ad45e10afa0a24c +Author: Stefan Roese +Date: Thu Dec 13 14:52:53 2007 +0100 + + ppc4xx: Bring 4xx fdt support up-to-date + + This patch update the 4xx fdt support. It enabled fdt booting + on the AMCC Kilauea and Sequoia for now. More can follow later + quite easily. + + Signed-off-by: Stefan Roese + +commit 0dc80e2759fba859ccc4cdadc633577ca2971f3e +Author: Stefan Roese +Date: Thu Dec 27 07:50:54 2007 +0100 + + cfi_flash: Add missing check for erased dest to flash_write_cfibuffer() + + The check for an sufficiently erased destination was missing in the + buffered write function of the cfi flash driver (when + CFG_FLASH_USE_BUFFER_WRITE is defined). This patch adds this check to that + writing to such a region will fail with the currect error message. + + Signed-off-by: Stefan Roese + +commit 33ed73bc0e38d0f2b5c183d4629d8f207e5b9994 +Author: Martin Krause +Date: Mon Nov 12 10:56:17 2007 +0100 + + Some configuration updates for the TQM5200 based TB5200 board: + + - enable command line history + - increase malloc space (because of bigger flash sectors) + + Signed-off-by: Martin Krause + +commit e318d9e9021a0af7508171f84ed09d0e79f0284e +Author: Martin Krause +Date: Thu Sep 27 11:10:08 2007 +0200 + + TQM8xx: use the CFI flash driver on all TQM8xx boards + + Signed-off-by: Martin Krause + +commit 11d9eec479b470eab9242ab937fca70a876d9376 +Author: Martin Krause +Date: Wed Sep 26 17:55:56 2007 +0200 + + TQM885D: adjust for doubled flash sector size + some minor fixes + + Signed-off-by: Martin Krause + +commit 22d1a56cbfb0bff34f477b4db6a55d076d829b83 +Author: Jens Gehrlein +Date: Wed Sep 26 17:55:54 2007 +0200 + + TQM885D: Exchanged SDRAM timing by a more relaxed timing. + + CAS-Latency=2, Write Recovery Time tWR=2 + The max. supported bus frequency is 66 MHz. Therefore, changed + threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz. + + Signed-off-by: Martin Krause + +commit b988b8cd443989be65161888eea0127ad03f846f +Author: Martin Krause +Date: Wed Sep 26 17:55:56 2007 +0200 + + TQM885D: use calculated cpuclk instead of measuring it + + On the TQM885D the measurement of cpuclk with the PIT reference + timer ist not necessary. Since all module variants use the same + external 10 MHz oscillator, the cpuclk only depends on the PLL + configuration - which is readable by software. + + Signed-off-by: Martin Krause + +commit 492c7049869348d31168de8dad89651315e468e0 +Author: Jens Gehrlein +Date: Thu Sep 27 14:54:46 2007 +0200 + + TQM885D: fix SDRAM refresh + + At 133 MHz the current SDRAM refresh rate is too fast + (measured 4 * 1.17 us). + CFG_MAMR_PTA changes from 39 to 128. This result + in a refresh rate of 4 * 7.8 us at the default clock + 66 MHz. At 133 MHz the value will be then 4 * 3.8 us. + This is a compromise until a new method is found to + adjust the refresh rate. + + Signed-off-by: Martin Krause + +commit dabad4b9bc46908e301f73ce76b38b23626a96e9 +Author: Jens Gehrlein +Date: Thu Sep 27 14:54:46 2007 +0200 + + TQM860M: Support for 10col SDRAMs, max. 128 MiB + + Signed-off-by: Martin Krause + +commit 61fb15c516fef5631e305f1976d7b3a679725856 +Author: Wolfgang Denk +Date: Thu Dec 27 01:52:50 2007 +0100 + + Fix coding style issues; update CHANGELOG. + + Signed-off-by: Wolfgang Denk + +commit 467bcee11fe26ad422f2de971aa70866079870f2 +Author: Haavard Skinnemoen +Date: Fri Dec 14 15:36:18 2007 +0100 + + cfi_flash: Add manufacturer-specific fixups + + Run fixups based on the JEDEC manufacturer ID independent of the + command set ID. + + This changes current behaviour: Previously, geometry reversal for AMD + chips were done based on the command set ID, while they are now done + based on the JEDEC manufacturer and device ID. + + Also add fixup for top-boot Atmel chips. A fixup is needed for + AT49BV6416(T) too, but since u-boot currently only reads the low byte + of the device ID, there's no way to tell it apart from AT49BV642D, + which should not have this fixup. Since AT49BV642D support is + necessary to get ATNGW100 board support into mainline, I've commented + out the fixup for now. + + Signed-off-by: Haavard Skinnemoen + +commit 0ddf06ddf6b4bd057ad4c5f0dffea7870ba06a2a +Author: Haavard Skinnemoen +Date: Fri Dec 14 15:36:17 2007 +0100 + + cfi_flash: Add cmdset-specific init functions + + Move things like reading JEDEC IDs and fixing up geometry reversal + into separate functions. The geometry reversal fixup is now performed + by altering the qry structure directly, which makes the sector init + code slightly cleaner. + + Signed-off-by: Haavard Skinnemoen + +commit e23741f4a6d8047520ef0d4971762749b3587d32 +Author: Haavard Skinnemoen +Date: Fri Dec 14 15:36:16 2007 +0100 + + cfi_flash: Read whole QRY structure in one go + + Read out the whole CFI Standard Query structure after successful cfi + identification. This allows subsequent code to access this information + directly without having to go through flash_read_uchar() and friends. + + Signed-off-by: Haavard Skinnemoen + +commit df9c25ea04b38a0e05d4f8c73c5cc144cdafa7db +Author: Haavard Skinnemoen +Date: Mon Dec 17 11:02:44 2007 +0100 + + AVR32: Fix logic inversion in disable_interrupts() + + disable_interrupts() should return nonzero if interrupts were + _enabled_ before, not disabled. + + Signed-off-by: Haavard Skinnemoen + +commit acac475212cbedb17b321a363a1c878e2b47b37f +Author: Haavard Skinnemoen +Date: Fri Dec 14 16:51:22 2007 +0100 + + AVR32: Enable interrupts at bootup + + The timer code depends on the timer interrupt to keep track of the + upper 32 bits of the cycle counter. This obviously doesn't work when + interrupts are disabled the whole time. + + Signed-off-by: Haavard Skinnemoen + +commit 9570bcd87f4db255514f43b6701746c412f8fef0 +Author: Haavard Skinnemoen +Date: Thu Nov 15 10:03:45 2007 +0100 + + AVR32: Fix wrong pin setup for USART3 + + As reported by Gerhard Berghofer: + + in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18 + instead of PB18 and PB19. + + which is obviously correct. There's currently no code that uses + USART3, but custom boards may run into problems. + + Signed-off-by: Haavard Skinnemoen + +commit 09ea0de03dcc3ee7af045b0b572227bda2c1c918 +Author: Haavard Skinnemoen +Date: Thu Nov 1 12:44:20 2007 +0100 + + README: Remove ATSTK1000 daughterboard list + + As noted by Kim Phillips, these lists tend to become out of date. + + Signed-off-by: Haavard Skinnemoen + +commit c81cbbad21cb0ae983e2e796211202234cdc8be2 +Author: Haavard Skinnemoen +Date: Tue Oct 30 14:56:36 2007 +0100 + + Add ATSTK100[234] to MAINTAINERS + + Add all the ATSTK1000 daughterboards to MAINTAINERS along with their + "mother". Also update the entry for ATSTK1000 to be not only about the + AP7000 CPU; it's intended to handle all CPUs in the AT32AP family. + + Signed-off-by: Haavard Skinnemoen + +commit 64ff2357b1727213803591813dbc779c924bf772 +Author: Haavard Skinnemoen +Date: Mon Oct 29 13:02:54 2007 +0100 + + AVR32: Add support for the ATSTK1004 board + + ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU, + which is a derivative of AT32AP7000. + + Signed-off-by: Haavard Skinnemoen + +commit 667568db157f374b85abd7e03596ddd1f0b25681 +Author: Haavard Skinnemoen +Date: Mon Oct 29 13:02:54 2007 +0100 + + AVR32: Add support for the ATSTK1003 board + + ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU, + which is a derivative of AT32AP7000. + + Signed-off-by: Haavard Skinnemoen + +commit 5fee84a794a51ec830548cda485a770efb018b92 +Author: Haavard Skinnemoen +Date: Mon Oct 29 13:23:33 2007 +0100 + + AVR32: Make some AT32AP700x peripherals optional + + Add a chip-features file providing definitions of the form + + AT32AP700x_CHIP_HAS_ + + to indicate the availability of the given peripheral on the currently + selected chip. + + Signed-off-by: Haavard Skinnemoen + +commit 36f28f8a9605ee5dcfa330482cfc62171261af97 +Author: Haavard Skinnemoen +Date: Mon Oct 29 13:09:56 2007 +0100 + + AVR32: Rename at32ap7000 -> at32ap700x + + The SoC-specific code for all the AT32AP700x CPUs is practically + identical; the only difference is that some chips have less features + than others. By doing this rename, we can add support for the AP7000 + derivatives simply by making some features conditional. + + Signed-off-by: Haavard Skinnemoen + +commit 4d5fa99c73f354e7cf985efcf417ea55ca2f6a5e +Author: Haavard Skinnemoen +Date: Fri Jun 29 18:22:34 2007 +0200 + + atmel_mci: Show SR when block read fails + + Show controller status as well as card status when an error occurs + during block read. + + Signed-off-by: Haavard Skinnemoen + +commit 8697e6a19b10f514511b6a9c86de88bd108c4f8d +Author: Stefan Roese +Date: Thu Dec 13 14:52:53 2007 +0100 + + ppc4xx: Bring 4xx fdt support up-to-date + + This patch update the 4xx fdt support. It enabled fdt booting + on the AMCC Kilauea and Sequoia for now. More can follow later + quite easily. + + Signed-off-by: Stefan Roese + +commit 12d30aa79779c2aa7a998bbae4c075f822a53004 +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:34 2007 +0100 + + cfi_flash: Use map_physmem() and unmap_physmem() + + Use map_physmem() and unmap_physmem() to convert from physical to + virtual addresses. This gives the arch a chance to provide an uncached + mapping for flash accesses. + + Signed-off-by: Haavard Skinnemoen + +commit 4d7d6936eb29af7cca330937808312aa5f61454d +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:33 2007 +0100 + + Introduce map_physmem() and unmap_physmem() + + map_physmem() returns a virtual address which can be used to access a + given physical address without involving the cache. unmap_physmem() + should be called when the virtual address returned by map_physmem() is + no longer needed. + + This patch adds a stub implementation which simply returns the + physical address cast to a uchar * for all architectures except AVR32, + which converts the physical address to an uncached virtual mapping. + unmap_physmem() is a no-op on all architectures, but if any + architecture needs to do such mappings through the TLB, this is the + hook where those TLB entries can be invalidated. + + Signed-off-by: Haavard Skinnemoen + +commit cdbaefb5f5f03e54455d0439dcf6dbd97ead1f9d +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:32 2007 +0100 + + cfi_flash: Introduce read and write accessors + + Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use + them to access the flash memory. This makes it clearer when the flash + is actually being accessed; merely dereferencing a volatile pointer + looks just like any other kind of access. + + Signed-off-by: Haavard Skinnemoen + +commit 812711ce6b3a386125dcf0d6a59588e461abbb87 +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:31 2007 +0100 + + Implement __raw_{read,write}[bwl] on all architectures + + This adds implementations of __raw_read[bwl] and __raw_write[bwl] to + m68k, ppc, nios and nios2. The m68k and ppc implementations were taken + from Linux. + + Signed-off-by: Haavard Skinnemoen + +commit be60a9021c82fc5aecd5b2b1fc96f70a9c81bbcd +Author: Haavard Skinnemoen +Date: Sat Oct 6 18:55:36 2007 +0200 + + cfi_flash: Reorder functions and eliminate extra prototypes + + Reorder the functions in cfi_flash.c so that each function only uses + functions that have been defined before it. This allows the static + prototype declarations near the top to be eliminated and might allow + gcc to do a better job inlining functions. + + Signed-off-by: Haavard Skinnemoen + +commit 3055793bcbdf24b1f8117f606ffb766d32eb766f +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:29 2007 +0100 + + cfi_flash: Make some needlessly global functions static + + Make functions not declared in any header file static. + + Signed-off-by: Haavard Skinnemoen + +commit 7e5b9b471518c5652febc68ba62b432193d6abf4 +Author: Haavard Skinnemoen +Date: Thu Dec 13 12:56:28 2007 +0100 + + cfi_flash: Break long lines + + This patch tries to keep all lines in the cfi_flash driver below 80 + columns. There are a few lines left which don't fit this requirement + because I couldn't find any trivial way to break them (i.e. it would + take some restructuring, which I intend to do in a later patch.) + + Signed-off-by: Haavard Skinnemoen + +commit 42026c9cb3a76849b41e6e24abfb7b56807a5c1a +Author: Bartlomiej Sieka +Date: Tue Dec 11 13:59:57 2007 +0100 + + CFI: synchronize command offsets with Linux CFI driver + + Fixes non-working CFI Flash on the Inka4x0 board. + + Signed-off-by: Bartlomiej Sieka + +commit 8ff3de61fc5f9b3b21647bce081a3b7f710f0d4d +Author: Kumar Gala +Date: Fri Dec 7 12:17:34 2007 -0600 + + Handle MPC85xx PCIe reset errata (PCI-Ex 38) + + On the MPC85xx boards that have PCIe enable the PCIe errata fix. + (MPC8544DS, MPC8548CDS, MPC8568MDS). + + Signed-off-by: Kumar Gala + +commit 82ac8c97145a4c3bf8b3dbfad00fa96e920f9b9c +Author: Kumar Gala +Date: Fri Dec 7 12:04:30 2007 -0600 + + Update Freescale MPC85xx ADS/CDS/MDS board config + + * Enabled CONFIG_CMD_ELF + + Signed-off-by: Kumar Gala + +commit d435793229ce29a42797c1edc39f5b34f987f91a +Author: Kumar Gala +Date: Fri Dec 7 04:59:26 2007 -0600 + + Handle Asynchronous DDR clock on 85xx + + The MPC8572 introduces the concept of an asynchronous DDR clock with + regards to the platform clock. + + Introduce get_ddr_freq() to report the DDR freq regardless of sync/async + mode. + + Signed-off-by: Kumar Gala + +commit 22abb2d2eaf7b795a6923c6273ec9cb53fda9a10 +Author: Kumar Gala +Date: Thu Nov 29 10:34:28 2007 -0600 + + Update Freescale MPC85xx ADS/CDS/MDS board config + + * Removed some misc environment setup + * Enabled CONFIG_CMDLINE_EDITING + + Signed-off-by: Kumar Gala + +commit 415a613babb84d5e5d5b42e8e553868c71fc3a64 +Author: Kumar Gala +Date: Thu Nov 29 10:47:44 2007 -0600 + + Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala + +commit c2d943ffbfd3359b3b45d177b437379d2cb86fbf +Author: Kumar Gala +Date: Thu Nov 29 10:16:18 2007 -0600 + + Move the MPC8540 ADS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala + +commit 870ceac5b3a3486c109396e005af81ae762b5710 +Author: Kumar Gala +Date: Thu Nov 29 10:14:50 2007 -0600 + + Move the MPC8560 ADS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala + +commit acbca876fb3fec25cd9c55b0efc81ff618ff5262 +Author: Kumar Gala +Date: Thu Nov 29 10:13:47 2007 -0600 + + Move the MPC8568 MDS board under board/freescale. + + Minor path corrections needed to ensure buildability. + + Signed-off-by: Kumar Gala + +commit a853d56c59b33415304531443633808736acfc6e +Author: Kumar Gala +Date: Thu Nov 29 02:18:59 2007 -0600 + + Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx + + We already had defines for LAWAR_TRGT_IF_* that we should use + rather than creating new ones. Also, added some missing defines for + PCIE targets. + + Signed-off-by: Kumar Gala + +commit 04db400892da37b76a585e332a0c137954ad2015 +Author: Kumar Gala +Date: Thu Nov 29 02:10:09 2007 -0600 + + Stop using immap_t on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_*_ADDR as the base of the registers + instead of getting it via &immap. + + Signed-off-by: Kumar Gala + +commit 2714223f8e04ab3e4133ff65872eef366d90bfea +Author: Kumar Gala +Date: Thu Nov 29 01:23:09 2007 -0600 + + Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt + + Signed-off-by: Kumar Gala + +commit c480861bf000156e6a3e932c258db59ff2212dd3 +Author: Kumar Gala +Date: Thu Nov 29 01:06:19 2007 -0600 + + Update MPC8568 MDS to use libfdt + + Updated the MPC8568 MDS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala + +commit 1563f56e0c68f6920f956382d6d13bee3f01c0f7 +Author: Haiying Wang +Date: Wed Nov 14 15:52:06 2007 -0500 + + Add PCI Express support on MPC8568MDS + + Signed-off-by: Haiying Wang + Signed-off-by: Kumar Gala + +commit b90d25497625b90ffa3f2911a0895ca237556ff5 +Author: Kumar Gala +Date: Thu Nov 29 00:11:44 2007 -0600 + + Update MPC85xx CDS to use libfdt + + Updated the MPC85xx CDS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala + +commit 0fd5ec66b10521a057ad73e69ab5f0f9eafba255 +Author: Kumar Gala +Date: Wed Nov 28 22:54:27 2007 -0600 + + Update MPC8540 ADS to use libfdt + + Updated the MPC8540 ADS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala + +commit 5ce715802f6c50dc78b3405b92f184b1e3710519 +Author: Kumar Gala +Date: Wed Nov 28 22:40:31 2007 -0600 + + Update MPC8560 ADS to use libfdt + + Updated the MPC8560 ADS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala + +commit aafeefbdb8b029f5ca2a195598d0a501a606eea9 +Author: Kumar Gala +Date: Wed Nov 28 00:36:33 2007 -0600 + + Stop using immap_t for cpm offset on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers + instead of getting it via &immap->im_cpm. + + Signed-off-by: Kumar Gala + +commit f59b55a5b8fcadaa99781ba48e7a38e956afa527 +Author: Kumar Gala +Date: Tue Nov 27 23:25:02 2007 -0600 + + Stop using immap_t for guts offset on 85xx + + In the future the offsets to various blocks may not be in same location. + Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers + instead of getting it via &immap->im_gur. + + Signed-off-by: Kumar Gala + +commit 50c03c8cf494d91cdec39670d95337c743e16ec9 +Author: Kumar Gala +Date: Tue Nov 27 22:42:34 2007 -0600 + + Update MPC8544 DS config + + * Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2 + * Removed some misc environment setup + * Moved to using fdtfile & fdtaddr as fdt env var names + * Enabled CONFIG_CMDLINE_EDITING + + Signed-off-by: Kumar Gala + +commit addce57e2e4c49e77ffb2020a84690713bb18b47 +Author: Kumar Gala +Date: Mon Nov 26 17:12:24 2007 -0600 + + Update MPC8544DS to use libfdt + + Updated the MPC8544DS config to use libfdt and assume use of aliases for + ethernet, pci, and serial for the various fixups that are done. + + Signed-off-by: Kumar Gala + +commit f852ce72f100cabd1f11c21c085a0ad8eca9fb65 +Author: Kumar Gala +Date: Thu Nov 29 00:15:30 2007 -0600 + + Add libfdt based ft_cpu_setup for mpc85xx + + Signed-off-by: Kumar Gala + +commit 3b9abdc448a1c2c6a4c2aa292724b4d1a05166a9 +Author: Stefan Roese +Date: Tue Dec 11 13:38:19 2007 +0100 + + ppc4xx: Correct GPIO offset in gpio_config() + + Thanks to Gary Jennejohn for pointing this out. + + Signed-off-by: Stefan Roese + +commit 8809a2713b1ceaf3da55d9d785470294f15de06a +Author: Stefan Roese +Date: Tue Dec 11 11:46:01 2007 +0100 + + rtc: Fix merging problem + + Signed-off-by: Stefan Roese + +commit 7cfc12a7dcfdb350e2ab76db4dafcc30f7e77c2b +Author: Stefan Roese +Date: Sat Dec 8 14:47:34 2007 +0100 + + ppc4xx: 405EX: Correctly enable USB pins + + This patch selects the USB data pins in the 405EX GPIO and MFC (multi + function control) registers. This is done for the AMCC Kilauea and + Makalu eval boards. + + Signed-off-by: Stefan Roese + +commit 9692c2734a47f23b44a0f68042a3e2ca8d1bfb39 +Author: Stefan Roese +Date: Sat Dec 8 08:25:09 2007 +0100 + + CFI: Coding style cleanup + + Signed-off-by: Stefan Roese + +commit 81b20ccc2d795ae9a1199db5a50ad9c28d1e4d22 +Author: Michael Schwingen +Date: Fri Dec 7 23:35:02 2007 +0100 + + CFI: support JEDEC flash roms in CFI-flash framework + + The following patch adds support for non-CFI flash ROMS, by hooking into the + CFI flash code and using most of its code, as recently discussed here in the + thread "Mixing CFI and non-CFI flashs". + + Signed-off-by: Michael Schwingen + Signed-off-by: Stefan Roese + +commit c01b17dd856fa120b2970f50d9598546a4927ec3 +Author: Gerald Van Baren +Date: Wed Nov 28 21:24:50 2007 -0500 + + Conditionally compile fdt_fixup_ethernet() + + Fix compiler warnings: On boards that don't have ethernets defined, + don't compile fdt_fixup_ethernet(). + +commit 246d4ae6bc282bc1841224e1c5fc49dc925e0bf7 +Author: Kumar Gala +Date: Tue Nov 27 21:59:46 2007 -0600 + + Convert boards that set memory node to use fdt_fixup_memory() + + Signed-off-by: Kumar Gala + +commit 151c8b09b35eebe8fd9139cb6c1d91c27b22f058 +Author: Kumar Gala +Date: Mon Nov 26 17:06:15 2007 -0600 + + Added fdt_fixup_stdout that uses aliases to set linux,stdout-path + + We use a combination of the serialN alias and CONFIG_CONS_INDEX to + determine which serial alias we should set linux,stdout-path to. + + Signed-off-by: Kumar Gala + +commit 3c9272813fad84c691d0e4989bb18a3ffebdebfc +Author: Kumar Gala +Date: Mon Nov 26 14:57:45 2007 -0600 + + Add common memory fixup function + + Add the function fdt_fixup_memory() to fixup the /memory node of the fdt + + Signed-off-by: Kumar Gala + +commit 9c9109e7fcf7ac2ca19c95b8ac54b8d1c773b157 +Author: Kumar Gala +Date: Mon Nov 26 11:19:12 2007 -0600 + + Conditionally compile fdt_support.c + + Modify common/Makefile to conditionally compile fdt_support.c based + on CONFIG_OF_LIBFDT. + + Signed-off-by: Kumar Gala + +commit d88e7ba0980773479e1a64badb293116071b7ef0 +Author: Kumar Gala +Date: Mon Nov 26 10:41:40 2007 -0600 + + Fix build breakage due to libfdt import + + The IDS8247 got lost in the update and need an API update + do to rename of functions in libfdt. + + Signed-off-by: Kumar Gala + +commit 28f384b171bbf1fb2dafb1046e6d259a6b2f8714 +Author: Gerald Van Baren +Date: Fri Nov 23 19:43:20 2007 -0500 + + Add spaces around the = in the fdt print format. + + Signed-off-by: Gerald Van Baren + +commit 29592ecba3b932b9b152bcec6c0c0806412db4a3 +Author: Nobuhiro Iwamatsu +Date: Fri Dec 7 01:25:38 2007 +0900 + + sh: Moved driver of the SuperH dependence + + The composition of the directory in the drivers/ changed. + I moved SuperH serial driver and marubun PCMCIA driver. + + Signed-off-by: Nobuhiro Iwamatsu + +commit 41be969f4957115ed7b1fe8b890bfaee99d7a7a2 +Author: Wolfgang Denk +Date: Thu Dec 6 10:21:19 2007 +0100 + + Release v1.3.1 + + Signed-off-by: Wolfgang Denk + +commit cf5933ba1e97a1cd8f5f24070e820f21d976eaeb +Author: Wolfgang Denk +Date: Thu Dec 6 10:21:03 2007 +0100 + + ADS5121 Board: fix compile problem. + + Signed-off-by: Wolfgang Denk + +commit a27044b14a9e93678a82d7b35f202b93e7687abc +Author: Stefan Roese +Date: Thu Dec 6 05:58:43 2007 +0100 + + ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards + + This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by + setting the FIXD bit in the SDR0_MFR register. Here a description of the + symptoms: + + Problem Description + ------------------------------ + If a DMA is performed between memory and PCI with the DMA 1 Controller + using prefetch, and as a result uses a special purpose buffer selected by + the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29), + the first part of the transfer sequence is performed twice. The + PPC440SPe PCI Controller requests more data than was needed such that in + the case of enforce memory protection, a host CPU exception can occur. + No data is corrupted, because data transfer is stopped in the PCI + Controller. Prefetch enable is specified by setting DMA Configuration + Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0. + + Behavior that may be observed in a running system + --------------------------------------------------------------------------- + + 1. DMA performance is decreased because of the double access on the PCI bus + interface. + 2. If an illegal access to some address on the PCI bus is detected at the + system level, a machine check or similar system error may occur. + + Workarounds Available + ---------------------------------- + + 1. Do not program prefetch. Note that a prefetch command cannot be programmed + without selecting a special purpose buffer. + 2. To avoid crossing a physical boundary of the PCI slave device, add 512 + bytes of address to the PCI address range. + + This patch was originally provided by Pravin M. Bathija + from AMCC and slighly changed. + + Signed-off-by: Pravin M. Bathija + Signed-off-by: Stefan Roese + +commit a90921f71d225bf9e0f0fc7b8beadeb8001bf78a +Author: Stefan Roese +Date: Tue Dec 4 16:29:48 2007 +0100 + + ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 support + + Signed-off-by: Stefan Roese + +commit 8d4f040a3c15036a6ea25a9c39e7d89fefa8440d +Author: Wolfgang Denk +Date: Mon Dec 3 00:15:28 2007 +0100 + + Prepare for 1.3.1-rc1 + + Signed-off-by: Wolfgang Denk + +commit e15e33433e7c05111968dc9b434a52fd42cbd221 +Author: Stefan Roese +Date: Fri Nov 30 07:15:41 2007 +0100 + + ppc4xx: Kilauea: Add PCIe reset assertion upon power-up + + This manual PCIe reset triggering solves the problem seen with the + Intel EPRO/1000 card, which was not detected (link not established) + upon power-up reset. + + Signed-off-by: Stefan Roese + +commit 260eea5676ca46903a335686cc020b29c4ca46fe +Author: Nobuhiro Iwamatsu +Date: Thu Nov 29 01:21:54 2007 +0900 + + sh: Add SuperH boards maintainer to MAINTAINERS file + + Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file. + + Signed-off-by: Nobuhiro Iwamatsu + +commit aa9c4f1d22701a92347c1c81f34d12c8ad3a3747 +Author: Nobuhiro Iwamatsu +Date: Thu Nov 29 00:13:04 2007 +0900 + + sh: Add ms7750se support in MAKEALL + + Signed-off-by: Nobuhiro Iwamatsu + +commit c7144373427a178332bf9754131c8c34c52c200a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 27 09:44:53 2007 +0100 + + sh: Add sh3 and sh4 support in MAKEALL + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Nobuhiro Iwamatsu + +commit 130080874a3d28450098481a262c5f7c855e908d +Author: Nobuhiro Iwamatsu +Date: Sun Nov 25 02:51:17 2007 +0900 + + sh: Add document for SuperH. + + This document is a summary of information concerning SuperH of U-Boot. + + Signed-off-by: Nobuhiro Iwamatsu + +commit 33ecdc2f9d64926e1a6067b28f3a0aefc3b6d23d +Author: Nobuhiro Iwamatsu +Date: Sun Nov 25 02:39:31 2007 +0900 + + sh: Add marubun's pcmcia driver + + Marubun pcmcia is a chip for PCMCIA used with SuperH. + Of course, this can be used even by other architectures. + When use this driver, came to be able to use CompactFlash + and Ethernet. + + Signed-off-by: Nobuhiro Iwamatsu + +commit febd86b969b975289ed948f1ac0eb9722da41ced +Author: Nobuhiro Iwamatsu +Date: Sun Nov 25 02:32:13 2007 +0900 + + sh: Update SuperH SCIF driver + + - Changed volatile unsigned to vu_. + - Changed Makefile for kconfig. + + Signed-off-by: Nobuhiro Iwamatsu + +commit 8be760903645af09871be50ad0a6f9ebb62b311d +Author: Stefan Roese +Date: Tue Nov 27 11:57:35 2007 +0100 + + ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexing + + After an error in the AMCC 405EX users manual now correctly configure + IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ + usage. + + Signed-off-by: Stefan Roese + +commit a5f601fd1b1278deae5aa9fc27a232b0d1c1c788 +Author: Wolfgang Denk +Date: Mon Nov 26 19:18:21 2007 +0100 + + Cleanup coding style; update CHANGELOG + + Signed-off-by: Wolfgang Denk + +commit 3deca9d44767efd1b83f4b701f0dbf21a7595f7b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Nov 25 22:39:25 2007 +0100 + + MAKEALL: add missing 512x boards in ppc + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit a340c325e668ca7386c2276387681720be9c3757 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Nov 25 18:45:47 2007 +0100 + + Makefile : fix tags ctags etags with new drivers organization + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 63362cfc6baa97ae0e37ba2c6ece530fcac9f79e +Author: Stefan Roese +Date: Mon Nov 26 15:06:14 2007 +0100 + + ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usage + + As suggested by Senao, use a different EBC_PB0AP setup for 400MHz + operation. + + Signed-off-by: Stefan Roese + +commit ca1ce226287270bb01e25b8e3674c701f12edf19 +Author: Stefan Roese +Date: Mon Nov 26 15:01:45 2007 +0100 + + ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interrupt + + Signed-off-by: Stefan Roese + +commit 87ddedd6ad804427ce125ceaa076d7a4f74e9d5d +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Nov 25 18:45:47 2007 +0100 + + Makefile : fix tags ctags etags with new drivers organization + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 59829cc189378c142c13d2aa8d9a897d8bef3961 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 21:26:56 2007 +0100 + + drivers/mtd : move mtd drivers to drivers/mtd + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 318c0b90431f2648552e5ade78833f42652ce859 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 21:17:55 2007 +0100 + + drivers/misc : move misc drivers to drivers/misc + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 33daf5b7858807cb4ce4158c2c56524671c14c08 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 21:13:59 2007 +0100 + + drivers/block : move block drivers to drivers/block + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0c698dcaa70275eb8814f665b545547cee013892 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 20:59:50 2007 +0100 + + drivers/rtc : move rtc drivers to drivers/rtc + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit f868cc5a50757d94f36c312395481cb0f187d9e6 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 20:14:44 2007 +0100 + + drivers/hwmon : move hardware monitor drviers to drivers/hwmon + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 16b195c82a18cbfd164800f17a1ef9db2e48331a +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 19:46:45 2007 +0100 + + drivers/input : move input drivers to drivers/input + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit e4558666293364fc3af1c1d9381ca933fa0f1275 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 19:40:11 2007 +0100 + + drivers/usb : move usb drivers to drivers/usb + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 1378df792a7ff3abd1bf54a63f5475784f5b083c +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 24 19:33:38 2007 +0100 + + drivers/serial : move serial drivers to drivers/serial + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 2439e4bfa111babf4bc07ba20efbf3e36036813e +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Nov 21 21:19:24 2007 +0100 + + drivers/net : move net drivers to drivers/net + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 352d259130b349fe9593b8dada641bd78a9659e5 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 20 20:41:48 2007 +0100 + + drivers/video : move video drivers to drivers/video + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 73646217186aa17afc8e305c5f06f06dd335eaad +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 20 20:33:09 2007 +0100 + + drivers/pcmcia : move pcmcia drivers to drivers/pcmcia + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 93a686ee9c5ddc6fa368c32cfbfde6f6724599fc +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 20 20:28:09 2007 +0100 + + drivers/pci : move pci drivers to drivers/pci + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 9162352817579840d7802da6d85872b3ca003c97 +Author: Gerald Van Baren +Date: Thu Nov 22 17:23:23 2007 -0500 + + Fix fdt printing for updated libfdt + + Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup. + + Signed-off-by: Gerald Van Baren + +commit 9eb77cea1fa12d5969eb26a1d1d81da381bd6b1c +Author: Kumar Gala +Date: Wed Nov 21 13:30:15 2007 -0600 + + Add additional fdt fixup helper functions + + Added the following fdt fixup helpers: + * do_fixup_by_prop{_u32} - Find matching nodes by property name/value + * do_fixup_by_compat{_u32} - Find matching nodes by compat + + The _u32 variants work the same only the property they are setting + is know to be a 32-bit integer instead of a byte buffer. + + Signed-off-by: Kumar Gala + +commit ab544633abdd14f4dd5d92e500b73eb59ef57e67 +Author: Kumar Gala +Date: Wed Nov 21 11:11:03 2007 -0600 + + Add fdt_fixup_ethernet helper to set mac addresses + + Added a fixup helper that uses aliases to set mac addresses + in the device tree based on the bd_t + + Signed-off-by: Kumar Gala + +commit dbaf07ce620aab249e3502b20a986234a6af1d3a +Author: Kumar Gala +Date: Wed Nov 21 14:07:46 2007 -0600 + + Fix warnings from import of libfdt + + cmd_fdt.c: In function fdt_print: + cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type + cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type + cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type + cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type + + Signed-off-by: Kumar Gala + +commit 8d04f02f6224e6983f4812ea4da704950ec8539c +Author: Kumar Gala +Date: Wed Oct 24 11:04:22 2007 -0500 + + Update libfdt from device tree compiler (dtc) + + Update libfdt to commit 8eaf5e358366017aa2e846c5038d1aa19958314e from + the device tree compiler (dtc) project. + + Signed-off-by: Kumar Gala + +commit e93becf80d732b64aef81b23e8b6ece02c40533d +Author: Kumar Gala +Date: Sat Nov 3 19:46:28 2007 -0500 + + Move do_fixup* for libfdt into common code + + Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260 + into common/fdt_support.c and renamed: + + do_fixup() -> do_fixup_by_path() + do_fixup_u32() -> do_fixup_by_path_u32() + + Signed-off-by: Kumar Gala + +commit f738b4a75998f42a7408defadc9baac7a31c92db +Author: Kumar Gala +Date: Thu Oct 25 16:15:07 2007 -0500 + + Make no options to fdt print default to '/' + + Signed-off-by: Kumar Gala + +commit a3c2933e02503fe36ade2c1b65af46f2b7a168e7 +Author: Kumar Gala +Date: Wed Oct 24 10:21:57 2007 -0500 + + Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt + + Removed: + fdt_node_is_compatible + fdt_find_node_by_type + fdt_find_compatible_node + + To ease merge of newer libfdt as we aren't using them anywhere at this time. + + Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same + reason. + + Signed-off-by: Kumar Gala + +commit 98e2867cc85409b919f862e6c16026461ec955df +Author: Grant Likely +Date: Wed Nov 21 09:19:37 2007 -0700 + + [BUILD] Remove libraries when updating autoconf.mk + + Fix library problems caused by conditional compilation. Using + autoconf.mk to decide which files to compile has caused a problem when + changing configuration from one board to another without clearing out + the library (*.a) files. + + It used to be that the linker was always passed the same list of .o + files when building the .a files. However, that is not longer true + with conditional compilation. Now, a different board config will have + a different file list passed to the linker. The problem occurs when + a library has already been built and the board config is changed. + + Since the linker will update instead of replace a preexisting library, + then if the file list changes to remove some object files the old + objects will still exist in the library. + + The solution is to remove all old library files when autoconf.mk is + made. + + Signed-off-by: Grant Likely + +commit ed1353d74b9ce8a7fcd660570b848a184d614b5f +Author: Kumar Gala +Date: Wed Nov 21 08:49:50 2007 -0600 + + [BUILD] conditionally compile libfdt/*.c in libfdt/Makefile + + Modify libfdt/Makefile to conditionally compile the *.c files based + on the board config. Signed-off-by: Kumar Gala -commit 4a43719a7738712811d822ca8125427b27a55cdc -Author: Grant Likely -Date: Mon Sep 24 09:05:31 2007 -0600 +commit 4a43719a7738712811d822ca8125427b27a55cdc +Author: Grant Likely +Date: Mon Sep 24 09:05:31 2007 -0600 + + [BUILD] conditionally compile common/cmd_*.c in common/Makefile + + Modify common/Makefile to conditionally compile the cmd_*.c files based + on the board config. + + Signed-off-by: Grant Likely + +commit 2f155f6c0a1f5e9a306a3f1f4fbe067db7ced3b1 +Author: Grant Likely +Date: Mon Sep 24 09:05:31 2007 -0600 + + [BUILD] Generate include/autoconf.mk from board config files + + Use cpp and sed to postprocess config.h and import the defined values + into include/autoconf.mk. autoconf.mk is then included by config.mk to + give 'make' access to the board configuration. + + Doing this enables conditional compilation at the Makefile level instead + of by wrapping every .c file with #ifdef/#endif wrappers. + + Signed-off-by: Grant Likely + +commit 68b88999da87ab88e71e1306192905be3450198e +Author: Jon Loeliger +Date: Tue Nov 20 15:02:26 2007 -0600 + + 8610HPCD: Enable the 8610 Display Interface Unit + + Signed-off-by: Jon Loeliger + +commit 74f89faa9d1e77ed947e628d3effaa513fe05d05 +Author: Jon Loeliger +Date: Tue Nov 20 15:00:53 2007 -0600 + + Move 8610 DIU interface structure definitions to header file. + + These two structures are still needed during the + initialization and setup of the DIU hardware. + So move them to the fsl_diu_fb.h file for now. + Official "blah". + + Noticed-by: York Sun + Signed-off-by: Jon Loeliger + +commit 080c646dbf474a109c3f85718fb01ce042a38c45 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 20 20:14:18 2007 +0100 + + drivers/i2c : move i2c drivers to drivers/i2c + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 9a337ddc154a10a26f117fd147b009abcdeba75a +Author: Wolfgang Denk +Date: Mon Nov 19 22:20:24 2007 +0100 + + Prepare for 1.3.0 release. + + Signed-off-by: Wolfgang Denk + +commit f30ad49b16bf998b03c1a5228b6c86369d61c258 +Author: Haiying Wang +Date: Mon Nov 19 10:02:13 2007 -0500 + + Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS + + CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it. + + Signed-off-by: Haiying Wang + +commit f8c320609366176b31104d9bf5e295232e1c7f1d +Author: Shinya Kuribayashi +Date: Mon Nov 19 11:14:16 2007 +0900 + + [MIPS] board/gth2/lowlevel_init.S: Fix a build warning + + lowlevel_init.S: Assembler messages: + lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local. + + Looking at codes, the `memtest' and `clearmem' are intentional mixed + use of `global symbols' and `label' for debugging purpose. To make it + build, just disable global-symbols-use for now. As a result `memtest' + still remains as unused, but leave it be... + + Signed-off-by: Shinya Kuribayashi + +commit e8da58f2bc092891e8cc92b927ed5c4bd0cb0cab +Author: Wolfgang Denk +Date: Mon Nov 19 12:59:14 2007 +0100 + + Fix build problems with mp2usb board + + Signed-off-by: Wolfgang Denk + +commit 6bf4c686afca1e86e1c384d59218f914605713bf +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Nov 18 18:36:11 2007 +0100 + + s3c24x0: Fix usb_ohci.c missing in Makefile + and usb_ohci.c warning differ in signedness + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 6073f61e078da5ddb521b56256bcc36508589883 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Nov 18 12:55:02 2007 +0100 + + pb1x00 board: Fix u16 status declaration when PCMCIA is defined + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 8412d814ce8bf5570a2b747f1e7fd321097fe987 +Author: Wolfgang Denk +Date: Sun Nov 18 17:11:09 2007 +0100 + + Fix compiler warnings for ARM systems. + + Signed-off-by: Wolfgang Denk + +commit 409ecdc0bb47dd28b0af6c25ffd658d22cc36b37 +Author: Wolfgang Denk +Date: Sun Nov 18 16:36:27 2007 +0100 + + Fix compiler warnings for PPC systems. Update CHANGELOG. + + Signed-off-by: Wolfgang Denk + +commit 653811a3c2b35856bf12e196dcc8c4694e28e420 +Author: Stefan Roese +Date: Sun Nov 18 14:44:44 2007 +0100 + + ppc4xx: Correct 405EX PCIe UTL register mapping + + Map 4k mem space for UTL registers for each port. + + Signed-off-by: Stefan Roese + +commit 079c2c4fa71c0d1ebef394508df9088df8a308d3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sat Nov 17 11:31:10 2007 +0100 + + Fix warning differ in signedness in net/net.c and net/nfs.c + +commit 7e14fc65368cbd2861b1207453da55a4fc7b3f81 +Author: Shinya Kuribayashi +Date: Sat Nov 17 20:42:45 2007 +0900 + + gth2.c: Fix a warning on gth2 build. + + gth2.c: In function 'misc_init_r': + gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness + + Signed-off-by: Shinya Kuribayashi + +commit 2309c130aa4c84b91bd874a41269c923eb61b555 +Author: Stefan Roese +Date: Sat Nov 17 07:58:25 2007 +0100 + + Fix warning differ in signedness in common/cmd_scsi.c + + Signed-off-by: Stefan Roese + +commit 9ea61b57968554eaf0f474ec7e088b17d367f474 +Author: Stefan Roese +Date: Sat Nov 17 14:52:29 2007 +0100 + + ppc4xx: Update AMCC Kilauea config file + + - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) + + Signed-off-by: Stefan Roese + +commit 7e1d884b7cb602007329c517ec1c453e3a6a5d9c +Author: Shinya Kuribayashi +Date: Sat Nov 17 20:05:26 2007 +0900 + + [MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker + + Current trick to pick up GNU assembler minor version does not work with the + latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to + "(GNU Binutils) ". + + $ sde-as --version |grep "GNU assembler" + GNU assembler 2.15.94 mipssde-6.02.02-20050602 + $ sde-as --version |grep "GNU assembler" |awk '{print $3}' + 2.15.94 + $ sde-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}' + 15 + $ + + $ mips-linux-as --version |grep "GNU assembler" + GNU assembler (GNU Binutils) 2.18 + $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' + (GNU + $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}' + (no output) + $ + + As a result of above, you'll see many noises with such binutils: + + make -C cpu/mips/ + /bin/sh: line 0: [: : integer expression expected + /bin/sh: line 0: [: : integer expression expected + make[1]: Entering directory `/home/skuribay/devel/u-boot.git/cpu/mips' + mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o incaip_wdt.o incaip_wdt.S + /bin/sh: line 0: [: : integer expression expected + mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o cache.o cache.S + /bin/sh: line 0: [: : integer expression expected + mips-linux-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -Wall -Wstrict-prototypes -c -o asc_serial.o asc_serial.c + /bin/sh: line 0: [: : integer expression expected + + This patch simplifies the trick and makes it work with both versions of gas. + I also replace an expensive `awk (or gawk)' with `cut'. + + Signed-off-by: Shinya Kuribayashi + +commit 16664f72850846e645616da1c0fa5afcd6d15f15 +Author: Shinya Kuribayashi +Date: Sat Nov 17 20:05:26 2007 +0900 + + [MIPS] Remove useless instructions for initializing $gp. + + Signed-off-by: Shinya Kuribayashi + +commit 03c031d5660ea946c39af6e2e16267da857c609f +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:27:06 2007 +0900 + + [MIPS] MIPS 4K core: Coding style cleanups + + No logical changes. + + Signed-off-by: Shinya Kuribayashi + +commit f5e429d3860bba4c6ae8bead8f78349fa24491b2 +Author: Shinya Kuribayashi +Date: Sat Nov 17 20:05:20 2007 +0900 + + [MIPS] gth2.c: Fix a warning on gth2 build. + + gth2.c: In function 'misc_init_r': + gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness + + Signed-off-by: Shinya Kuribayashi + +commit 4fbd0741b2b6441da10be93e10267122581b7079 +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:22:33 2007 +0900 + + [MIPS] au1x00_eth.c: Fixed a warning on pb1000 build. + + au1x00_eth.c: In function 'au1x00_miiphy_write': + au1x00_eth.c:139: warning: 'return' with no value, in function returning non-void + + Signed-off-by: Shinya Kuribayashi + +commit f01320459736f156707425cf8112f98606301aa4 +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:00:25 2007 +0900 + + [MIPS] au1x00_eth.c: Fix au1x00_miiphy_{read,write} build error + + au1x00_eth.c: In function 'au1x00_enet_initialize': + au1x00_eth.c:246: error: 'au1x00_miiphy_read' undeclared (first use in this function) + au1x00_eth.c:246: error: (Each undeclared identifier is reported only once + au1x00_eth.c:246: error: for each function it appears in.) + au1x00_eth.c:246: error: 'au1x00_miiphy_write' undeclared (first use in this function) + au1x00_eth.c: In function 'au1x00_miiphy_write': + au1x00_eth.c:298: warning: 'return' with no value, in function returning non-void + make[1]: *** [au1x00_eth.o] Error 1 + + Fixed by moving these two functions forward. + + Signed-off-by: Shinya Kuribayashi + +commit b09258c5393edd1087c5f39ae68338f16b49f8b3 +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:00:25 2007 +0900 + + MAKEALL: Added missing pb1000 board + + Signed-off-by: Shinya Kuribayashi + +commit 2e4a6e3667a1e39c0e6e99498686b15d2718b369 +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:00:24 2007 +0900 + + [MIPS] pb1000: Replace obsolete memsetup.S with lowlevel_init.S + + Signed-off-by: Shinya Kuribayashi + +commit 662e5cb397249c3ea88a4c3255e9ccfc40b98d82 +Author: Shinya Kuribayashi +Date: Sat Oct 27 15:00:24 2007 +0900 + + [MIPS] u-boot.lds: Cleanup __u_boot_cmd_{start,end} + + Signed-off-by: Shinya Kuribayashi + +commit 5947f6999aafa7c54c1390983d264a8463dfea8e +Author: Wolfgang Denk +Date: Sat Nov 17 02:34:38 2007 +0100 + + Update CHANGELOIG, prepare for -rc4 + + Signed-off-by: Wolfgang Denk + +commit fd329e6f05bbdfe6bd71b0e09f0c76d3b0a025a5 +Author: Luotao Fu +Date: Wed Nov 14 18:58:33 2007 +0100 + + Fix the i2c frequency and default address in rsdproto board + + rsdproto board support has wrong I2C frequency and wrong return value + handling. + + Signed-off-by: Luotao Fu + +commit 429c180edad038f91c989cb14b478228092e7054 +Author: Wolfgang Denk +Date: Sat Nov 17 01:45:38 2007 +0100 + + powerpc: Backout relocation changes for MPC5121, too. + + Apply Grant Likely's backout to MPC5121 code, too. + + Pointed out by Rafal Jaworowski + + Signed-off-by: Wolfgang Denk + +commit 1c3dd43338a077165e7e0309cb3994e65d2bdbf8 +Author: Grant Likely +Date: Tue Nov 13 22:18:33 2007 -0700 + + powerpc: Backout relocation changes. + + Ugh. I *hate* to back this change out, but these compiler flags don't + work for relocation on all versions of GCC. I've not been able to + reproduce the environment in my setup (and hence, not been able to + find a combination that *does* work), so I've got no choice but to go + back to the old gcc flags and linker script. + + Signed-off-by: Grant Likely + +commit 5c15010efad980ad5498cc565fc1ed70df2f52b4 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Nov 13 09:11:05 2007 +0100 + + Fixed mips_io_port_base build errors. + + This patch has been sent on: + - 29 Sep 2007 + + Although mips_io_port_base is currently a part of IDE command, it is quite + fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move + it to MIPS general part, and introduce `set_io_port_base()' from Linux. + + This patch is triggered by multiple definition of `mips_io_port_base' build + error on gth2 (and tb0229 also needs this fix.) + + board/gth2/libgth2.a(gth2.o): In function `log_serial_char': + /home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base' + common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here + make: *** [u-boot] Error 1 + + Signed-off-by: Shinya Kuribayashi + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 6ecbb7a3fa9b0940ed33e490d195d4b6830b2422 +Author: Wolfgang Denk +Date: Sat Nov 17 01:30:40 2007 +0100 + + Fix a bug in the slave serial programming mode for the Xilinx + Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if + the most significant bit was set, which did not work on any + architecture where "char" defaulted to be an unsigned type. + + Based on a patch by Angelos Manousaridis + + Signed-off-by: Wolfgang Denk + +commit d08b7233bc252faad8339e7ca0ddfd62fa79903c +Author: Jon Loeliger +Date: Thu Nov 1 12:23:29 2007 -0500 + + 86xx: Fix broken variable reference when #def DEBUGing. + + Sometimes you can't reference the DDR2 controller variables. + + Signed-off-by: Jon Loeliger + +commit f9d9164d9c6b5a7f0393fd8d7e246b8a0326bc19 +Author: Jason Jin +Date: Fri Oct 26 18:32:00 2007 +0800 + + make 8610 board use pixis reset + + Signed-off-by: Jason Jin + +commit db74b3c1c9481a6bffbf8cd445e5bcbf6908e836 +Author: Jason Jin +Date: Mon Oct 29 19:26:21 2007 +0800 + + Unify pixis_reset altbank across board families + + Basically, refactor the CFG_PIXIS_VBOOT_MASK values + into the separate board config files. + + Signed-off-by: Jason Jin + Signed-off-by: Jon Loeliger + +commit 64bf555465c7926be13e1046ac0d0f05ac72829c +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Nov 7 08:19:21 2007 +0100 + + Fix warning: pointer targets in assignment differ in signedness + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 7a60ee7c6248a958c5757d3660a1702723a2786d +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Nov 7 08:19:19 2007 +0100 + + Fix warning differ in signedness in common/cmd_ide.c + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit f31d38b9eea9b32f6a1ac848a298cc71ca4c9a03 +Author: Stefan Roese +Date: Fri Nov 16 14:16:54 2007 +0100 + + ppc4xx: Enable 405EX PCIe UTL register configuration + + Till now the UTL registers on 405EX were not initialized but left with + their default values. This patch new initializes some of the UTL + registers on 405EX. + + Signed-off-by: Stefan Roese + +commit ecdcbd4f8c1f8cefd785752f4e7536aae2a4ecf9 +Author: Stefan Roese +Date: Fri Nov 16 14:00:59 2007 +0100 + + ppc4xx: Update AMCC Makalu for board rev 1.1 + + This patch adds changes needed for Makalu rev 1.1: + + - Enable 2nd DDR2 bank resulting in 256MByte of SDRAM + - Enable 2nd ethernet port EMAC1 + - Use generic GPIO configuration framework (CFG_4xx_GPIO_TABLE) + - Reset PCIe ports via GPIO upon bootup + + Signed-off-by: Stefan Roese + +commit 4d4faae65e115e327425cd514c1a35146a85166b +Author: Grant Likely +Date: Mon Sep 24 09:05:31 2007 -0600 + + Group PCI and PCMCIA drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit 5798f87dc10a496d79d3177b9f5a76488987fd35 +Author: Grant Likely +Date: Mon Sep 24 09:05:31 2007 -0600 + + Group block/flash drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit df58c81551700f058b44cacf55a7997fa63bfe0a +Author: Grant Likely +Date: Mon Sep 24 09:05:31 2007 -0600 + + Group USB drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit 5dbb6ed622e539b0c8493ef7e578d3a533181d29 +Author: Grant Likely +Date: Mon Sep 24 09:05:30 2007 -0600 + + Group i2c drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit ec00c76de0e5971273905998d62d6bb119324218 +Author: Grant Likely +Date: Mon Sep 24 09:05:30 2007 -0600 + + Group console drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit 754f230aa01b8c789fc31f8013c2487954073300 +Author: Grant Likely +Date: Mon Sep 24 09:05:30 2007 -0600 + + Group network drivers in drivers/Makefile + + Signed-off-by: Grant Likely + +commit f0037c56b0d12cd46215124667b9f83d60ef9391 +Author: Grant Likely +Date: Mon Sep 24 09:05:30 2007 -0600 + + Build: split COBJS value into multiple lines + + This change is in preparation for condtitionial compile support in the + build system. By spliting them all into seperate lines now, subsequent + patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_) += ' will + be less invasive and easier to review + + Signed-off-by: Grant Likely + +commit 1b4aaffe4fb2a5e95d9111a5d94fd1f89215dce4 +Author: Grant Likely +Date: Mon Sep 24 09:05:30 2007 -0600 + + Add .gitignore files + + Signed-off-by: Grant Likely + Acked-by: Kim Phillips + +commit 955413f35f054a82e40042f1dbcf501c6a05719b +Author: Grant Likely +Date: Thu Nov 15 08:27:52 2007 -0700 + + Revert "Correct relocation fixup for mpc5xx" + + This reverts commit 3649cd99ba815b6601868735765602f00ef3692b. + Signed-off-by: Grant Likely + +commit e15633888a058aacb31a62d2cf1278e1e4c236ab +Author: Grant Likely +Date: Thu Nov 15 08:24:32 2007 -0700 + + Revert "Correct fixup relocation for MPC5xxx" + + This reverts commit 6f7576b20ecf0d040c3ac3b032b5cbc860e38a90. + Signed-off-by: Grant Likely + +commit 139365fbe566d0fc619a1ed04452ec5388f0cef8 +Author: Grant Likely +Date: Thu Nov 15 08:21:04 2007 -0700 + + Revert "Correct fixup relocation for mpc8220" + + This reverts commit a85dd254c0577fca13627c46e93fc2ad4c4f1f00. + Signed-off-by: Grant Likely + +commit 70922342369e5e39b286fe21e768a239ca07a514 +Author: Grant Likely +Date: Thu Nov 15 08:20:57 2007 -0700 + + Revert "Correct fixup relocation for mpc824x" + + This reverts commit f3a52fe05923935db86985daf9438e2f70ac39aa. + Signed-off-by: Grant Likely + +commit 96279ab4cad60cb5972aa934fbe4845ac02cc75a +Author: Grant Likely +Date: Thu Nov 15 08:20:50 2007 -0700 + + Revert "Correct fixup relocation for mpc8260" + + This reverts commit 5af61b2f4b838a05f79be274f3e5a66edd2d9c96. + Signed-off-by: Grant Likely + +commit 928fe33b24cdf382a8dc8687fed24b1961cdb5d6 +Author: Grant Likely +Date: Thu Nov 15 08:20:43 2007 -0700 + + Revert "Correct fixup relocation for mpc83xx" + + This reverts commit 057004f4a4863554d56cc56268bfa7c7d9738e27. + Signed-off-by: Grant Likely + +commit c93945e8f9e300860d2bf73a2549ce5794f8bd00 +Author: Grant Likely +Date: Thu Nov 15 08:20:25 2007 -0700 + + Revert "[MPC512x] Correct fixup relocation" + + This reverts commit 8d17979d0359492a822a0a409d26e3a3549b4cd4. + Signed-off-by: Grant Likely + +commit c9672f81f1bdb4e8ddf62aa72ca0206e8b72aa1c +Author: Stefan Roese +Date: Thu Nov 15 14:25:09 2007 +0100 + + ppc4xx: Small AMCC Kilauea cleanup + + Remove not needed pci_target_init() function. + + Signed-off-by: Stefan Roese + +commit aee747f19b460a0e9da20ff21e90fdaac1cec359 +Author: Stefan Roese +Date: Thu Nov 15 14:23:55 2007 +0100 + + ppc4xx: Enable 440 GPIO init table CFG_440_GPIO_TABLE for 405 platforms + + - Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE + - Cleanup of the 4xx GPIO functions + - Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h + + Signed-off-by: Stefan Roese + +commit 8ada0ebf38e4073beea0309188b25d82a112a2ae +Author: Stefan Roese +Date: Thu Nov 15 14:20:08 2007 +0100 + + ppc4xx: AMCC Taihu board config file cleanup + + This patch makes the AMCC Taihu a little more compatible to the other + AMCC eval boards. + + Signed-off-by: Stefan Roese + +commit 5e71c51d74c963d3174060c078dcacf13bdd02ef +Author: Marian Balakowicz +Date: Thu Nov 15 13:37:28 2007 +0100 + + [INKA4x0] NG hardware: flash support + + Disabled and remove inka4x0 custom flash driver, use CFI flash + driver instead. + + Signed-off-by: Marian Balakowicz + +commit 5fb6d7191e206cdde0e23140fd8111caed93a595 +Author: Marian Balakowicz +Date: Thu Nov 15 13:29:55 2007 +0100 + + [INKA4x0] NG hardware: SDRAM support + + Add support for three new DDR chips that may be present on a NG + INKA4x0 hardware: HYB25D512160BF-5, K4H511638C-7CB3, T46V32M16BN-6IT. + + Cleanup board/inka4x0/mt48lc16m16a2-75.h file. + + Signed-off-by: Marian Balakowicz + +commit f23cb34c367bb27585a4fdb8a75277370e7d0596 +Author: Marian Balakowicz +Date: Thu Nov 15 13:24:43 2007 +0100 + + [INKA4x0] NG hardware: platform code update + + - Cleanup compile warnings. + - Add missing '\0' in default environment. + - Increase CFG_MONITOR_LEN to 256 KiB. + - Add required CFG_USE_PPCENV. + + Signed-off-by: Marian Balakowicz + +commit 2ae64f5135e51bb18753884d1265b99e89b5aedd +Author: Peter Pearse +Date: Thu Nov 15 08:58:00 2007 +0000 + + Remove warnings re CONFIG_EXTRA_ENV_SETTINGS + Remove warnings re onenand_read() & write() + +commit 2db916e14410e3ec1738508c7bf4dfeb2b299ae7 +Author: Peter Pearse +Date: Thu Nov 15 08:45:13 2007 +0000 + + Correction patch + +commit 1d8a49eca1c7bdc8db1c47a92f9014a29ead03ae +Author: Roy Zang +Date: Thu Sep 13 18:52:28 2007 +0800 + + Enable ULi1575 Ethernet support in 8610HPCD config + + Signed-off-by: Roy Zang + Acked-by: Jon Loeliger + +commit 54fd6c93c28a0a45352fff5dd92673401ff563f2 +Author: Stefan Roese +Date: Tue Nov 13 08:18:20 2007 +0100 + + ppc4xx: lwmon5: Change PHY reset sequence for PHY MDIO address latching + + Signed-off-by: Stefan Roese + +commit 7d0a4066b5a6b698e5fc1b66cfe9705774bbce93 +Author: Stefan Roese +Date: Tue Nov 13 08:06:11 2007 +0100 + + ppc4xx: Fix 405EX PCIe UTLSET register setup + + Signed-off-by: Stefan Roese + +commit 1ce55151c85d068f70317a8d65c61058b891afb4 +Author: Heiko Schocher +Date: Tue Nov 13 07:50:29 2007 +0100 + + [UC101] SRAM now with 2 MB working. + + Signed-off-by: Heiko Schocher + +commit 2d14684341109a69616e4d6016cd61402d55086f +Author: Matthias Fuchs +Date: Fri Nov 9 15:37:53 2007 +0100 + + ppc4xx: Use generic usb-ohci driver for sequoia board + + This patch makes the sequoia board use the generic usb-ohci driver + instead of cpu/ppc4xx/usb_ohci.c. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 9be659ac0868dc367caa957c5c725e46b07f6a5f +Author: Matthias Fuchs +Date: Fri Nov 9 15:37:23 2007 +0100 + + ppc4xx: Make USB working with CONFIG_4xx_DCACHE defined + + This patch disables the 44x d-cache on 'usb start' and + reenables it on 'usb stop'. This should be seen as a + temporary fix until the generic usb-ohci driver can + life with d-cache enabled. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit fbde2169d2c48fcc9ff03489534a78ffb0a8a0d4 +Author: Matthias Fuchs +Date: Fri Nov 9 15:36:44 2007 +0100 + + ppc4xx: Remove redundant code from 4xx network driver + + This patch removes some redundant code and decrements the end + address of cache flush and invalidate by 1. + + Signed-off-by: Matthias Fuchs + Signed-off-by: Stefan Roese + +commit 5ca9881aad8c413ac2a82868a5e3719178254502 +Author: Peter Pearse +Date: Fri Nov 9 15:24:26 2007 +0000 + + Add apollon board support + Signed-off-by: Kyungmin Park + +commit b53313dbfc74525d85f1e7e0102f902d5c863beb +Author: Stefan Roese +Date: Fri Nov 9 12:19:58 2007 +0100 + + ppc4xx: Remove In:/Out:/Err: boot output for AMCC Kilauea + + Signed-off-by: Stefan Roese + +commit c7f69c340277935a6c19a956421852da944a365f +Author: Stefan Roese +Date: Fri Nov 9 12:18:54 2007 +0100 + + ppc4xx: Make output a little shorter on I2C bootrom detection + + Most 4xx PPC capable of using an I2C bootrom for bootstrap setting + already print a line with the information which I2C bootrom is + used for bootstrap configuration. So we don't need this extra line + with "I2C boot EEPROM en-/dis-abled". + + This patch also has a little code cleanup integrated. + + Signed-off-by: Stefan Roese + +commit 8d737a28152ec12873f8544cca1fb39a49e5e693 +Author: TsiChungLiew +Date: Thu Nov 8 12:50:18 2007 -0600 + + ColdFire: MCF5329 - Remove reset registers from CCM + + Signed-off-by: TsiChungLiew + +commit 7d7cdea769a60b0a6e4c18bef7f9d648fd14b8d7 +Author: TsiChungLiew +Date: Thu Nov 8 12:31:11 2007 -0600 + + ColdFire: MCF5329 - Add Reset structure to immap_5329.h + + Signed-off-by: TsiChungLiew + +commit 09b26cf00d76d75fdf7fdc4b13e4dd929743bc21 +Author: TsiChungLiew +Date: Thu Nov 8 12:19:01 2007 -0600 + + ColdFire: MCF5329 - revert include/asm-m68k/m5329.h file mode + + Signed-off-by: TsiChungLiew + +commit 225a24b5e062ad94627424508ae814f51dbe1a34 +Author: TsiChungLiew +Date: Wed Nov 7 18:00:54 2007 -0600 + + ColdFire: MCF5445x - Update correct RAMBAR and missing linker files + + Signed-off-by: TsiChungLiew + +commit 248c7c14835f34d5d910b45e5600050e58ca6cab +Author: TsiChungLiew +Date: Wed Nov 7 17:56:15 2007 -0600 + + ColdFire: MCF532x - Update do_reset() using core reset + + Signed-off-by: TsiChungLiew + +commit d9240a5f827eb3b476a6ba2938d01f1a9e7688f4 +Author: TsiChungLiew +Date: Wed Nov 7 17:51:00 2007 -0600 + + ColdFire: Update cpu flag for 4.2-xx compiler + + Signed-off-by: TsiChungLiew + +commit 070ba56115b4da63b46e974287fa4550d4023386 +Author: York Sun +Date: Wed Oct 31 14:59:04 2007 -0500 + + 8610: Add console frame buffer support to FSL 8610 DIU driver. + + Add cfb console support to FSL 8610 DIU driver. + Inspect board version from PIXIS to obtain correct pixel format. + + Use #define CONFIG_VIDEO in config file to enable fb console. + + To switch monitor, set monitor variable to + 0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS + followed by "diufb init". + + Preserve logo bitmap at the top of the fb console. + + Signed-off-by: York Sun + Signed-off-by: Jon Loeliger + +commit a877880c6949e948bd63cd6ea4e216573d2f53dd +Author: York Sun +Date: Mon Oct 29 13:58:39 2007 -0500 + + 8610: Add 8610 DIU display driver + + 1280x1024 and 1024x768 @ 32 bpp are supported now. + DVI, Single-link LVDS, Double-link LVDS are all supported. + + Environmental variable "monitor" is used to specify monitor port. + + A new command "diufb" is introduced to reinitialize monitor + and display a BMP file in the memory. So far, 1-bit, 4-bit, + 8-bit and 24-bit BMP formats are supported. + + diufb init + - initialize the diu driver + Enable the port specified in the environmental variable "monitor" + + diufb addr + - display bmp file in memory. + The bmp image should be no bigger than the resolution, 1280x1024 + for DVI and double-link LVDS, 1024x768 for single-link LVDS. + + Note, this driver allocate memory but doesn't free it after use + It is written on purpose -- to avoid a failure of reallocation + due to memory fragement. + + ECC of DDR is disabled for DIU performance. L2 data cache is also disabled. + + Signed-off-by: York Sun + Signed-off-by: Jon loeliger + +commit 52e5ddfecdda308f75782fae206b677b1810f5f9 +Author: York Sun +Date: Wed Oct 31 10:43:59 2007 -0500 + + FSL: Add a freescale bitmap logo. + + This Freescale logo is a 340 x 128 x 4bpp BMP file + that can be displayed by the DIU Framebuffer driver. + + Signed-off-by: York Sun + Signed-off-by: Jon Loeliger + +commit 1815338fbd1c0f94f8276d2891b99caa5a05f622 +Author: York Sun +Date: Mon Oct 29 13:57:53 2007 -0500 + + 8610: Make some extra debug environment variables conditional. + + One may #define ENV_DEBUG to get them back again. + + Signed-off-by: York Sun + +commit 761421ccca80a9fb37b19c37aa61d46ef75e0647 +Author: Jason Jin +Date: Mon Oct 29 19:26:21 2007 +0800 + + 8610: Actually enable pixis_reset CONFIGs + + Signed-off-by: Jason Jin + +commit f3bceaab230b4748d0afc4109b6837308f018b40 +Author: Jason Jin +Date: Fri Oct 26 18:31:59 2007 +0800 + + Fix the BAT definition of PCI IO on 8610 board + + The address in the BAT register is aligned with the BAT size. + The original definition actually did not define BAT for PCIE2 IO. + This patch fix this. + + Signed-off-by: Jason Jin + +commit 9f23ca334a6f5f021ef9e9d0fad9da80d63b2d56 +Author: Jason Jin +Date: Mon Oct 29 19:26:21 2007 +0800 + + Unify pixis_reset altbank across board families + + Basically, refactor the CFG_PIXIS_VBOOT_MASK values + into the separate board config files. + + Signed-off-by: Jason Jin + Signed-off-by: Jon Loeliger + +commit a8318ec205c8e8794b5f9f1b8584abadb440e8ba +Author: Jason Jin +Date: Fri Oct 26 18:32:00 2007 +0800 + + make 8610 board use pixis reset + + Signed-off-by: Jason Jin + +commit 9c84709eedce9c680dd695984ab7d2328f4f04f5 +Author: Jon Loeliger +Date: Thu Nov 1 12:23:29 2007 -0500 + + 86xx: Fix broken variable reference when #def DEBUGing. + + Sometimes you can't reference the DDR2 controller variables. + + Signed-off-by: Jon Loeliger + +commit 1f103105a3746ab12279b63b8c1d372c0ce2cc58 +Author: Roy Zang +Date: Mon Nov 5 17:39:24 2007 +0800 + + Implement general ULi 526x Ethernet driver support in U-boot + + This patch implements general ULi 526x Ethernet driver. + Until now, it is the only native Ethernet port on + MPC8610HPCD board, but it could be used on other boards + with ULi 526x Ethernet port as well. + + Signed-off-by: Roy Zang + Signed-off-by: Zhang Wei + Acked-by: Jon Loeliger + Signed-off-by: Ben Warren + +commit 71bc6e6474fea8ef481b9b45d1edd7ad1f6dfbbd +Author: Larry Johnson +Date: Thu Nov 1 08:46:50 2007 -0500 + + NET: Add Ethernet 1000BASE-X support for PPC4xx + + This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and + "miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which + returns non-zero iff the PHY registers are configured for 1000BASE-X. The + "mii info" command is modified to distinguish between 1000BASE-T and -X. + + Signed-off-by: Larry Johnson + Signed-off-by: Ben Warren + +commit 298035df4948b113d29ac0e694717d34b95bc5dc +Author: Larry Johnson +Date: Wed Oct 31 11:21:29 2007 -0500 + + NET: Cosmetic changes + + Signed-off-by: Larry Johnson + Signed-off-by: Ben Warren - [BUILD] conditionally compile common/cmd_*.c in common/Makefile +commit 654f38b3a387886996a5a75771fbfc29cb4f225e +Author: Stefan Roese +Date: Mon Nov 5 07:43:05 2007 +0100 - Modify common/Makefile to conditionally compile the cmd_*.c files based - on the board config. + ppc4xx: Make output a little shorter on PCIe detection - Signed-off-by: Grant Likely + Now not max 3 lines but 2 lines are printed per PCIe port. -commit 2f155f6c0a1f5e9a306a3f1f4fbe067db7ced3b1 -Author: Grant Likely -Date: Mon Sep 24 09:05:31 2007 -0600 + Signed-off-by: Stefan Roese - [BUILD] Generate include/autoconf.mk from board config files +commit 992742a5b09d9040adbd156fb90756af66ade310 +Author: Wolfgang Denk +Date: Sat Nov 3 23:09:27 2007 +0100 - Use cpp and sed to postprocess config.h and import the defined values - into include/autoconf.mk. autoconf.mk is then included by config.mk to - give 'make' access to the board configuration. + Cleanup coding style; update CHANGELOG - Doing this enables conditional compilation at the Makefile level instead - of by wrapping every .c file with #ifdef/#endif wrappers. + Signed-off-by: Wolfgang Denk - Signed-off-by: Grant Likely +commit e881cb563e32f45832b7b6db77bdcd017adcbb41 +Author: Bruce Adler +Date: Fri Nov 2 13:15:42 2007 -0700 -commit 080c646dbf474a109c3f85718fb01ce042a38c45 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 20 20:14:18 2007 +0100 + fix wording in README - drivers/i2c : move i2c drivers to drivers/i2c + Changed the wording to properly describe the shadowing + of the environment from ROM to RAM - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Bruce Adler -commit 9a337ddc154a10a26f117fd147b009abcdeba75a -Author: Wolfgang Denk -Date: Mon Nov 19 22:20:24 2007 +0100 +commit ad845beef06245426c57b53dcdc01b7dc70e0d45 +Author: Shinya Kuribayashi +Date: Wed Oct 31 02:18:15 2007 +0900 - Prepare for 1.3.0 release. + blackfin: Move `-D__BLACKFIN__' to $(ARCH)_config.mk - Signed-off-by: Wolfgang Denk + Signed-off-by: Shinya Kuribayashi -commit f30ad49b16bf998b03c1a5228b6c86369d61c258 -Author: Haiying Wang -Date: Mon Nov 19 10:02:13 2007 -0500 +commit ec22755799466c8a103664bb3a5e647bf9c238f4 +Author: Vlad Lungu +Date: Thu Oct 25 16:08:14 2007 +0300 - Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS + Trimmed some variables in ne2000.c - CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it. + Signed-off-by: Vlad Lungu - Signed-off-by: Haiying Wang +commit eb6f214d3644b2a77968c176ed36dcf858cfe7e0 +Author: Zhang Wei +Date: Thu Oct 25 17:51:27 2007 +0800 -commit f8c320609366176b31104d9bf5e295232e1c7f1d -Author: Shinya Kuribayashi -Date: Mon Nov 19 11:14:16 2007 +0900 + Fix the issue of usb_kbd driver missing the scan code of key 'z'. - [MIPS] board/gth2/lowlevel_init.S: Fix a build warning + The scan code of the key 'z' is 0x1d, which should be handled. - lowlevel_init.S: Assembler messages: - lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local. + The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI + controller. - Looking at codes, the `memtest' and `clearmem' are intentional mixed - use of `global symbols' and `label' for debugging purpose. To make it - build, just disable global-symbols-use for now. As a result `memtest' - still remains as unused, but leave it be... + Signed-off-by: Zhang Wei - Signed-off-by: Shinya Kuribayashi +commit bbf4796f6498fbade56d56eff3a0a49b299d93e5 +Author: Zhang Wei +Date: Thu Oct 25 17:30:04 2007 +0800 -commit e8da58f2bc092891e8cc92b927ed5c4bd0cb0cab -Author: Wolfgang Denk -Date: Mon Nov 19 12:59:14 2007 +0100 + Fix USB support issue for MPC8641HPCN board. - Fix build problems with mp2usb board + The configuration file has already enabled USB, but it + missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB + on MPC8641HPCN can not work because of the wrong USB + register endian. - Signed-off-by: Wolfgang Denk + And add the USB command to U-Boot commands list. -commit 6bf4c686afca1e86e1c384d59218f914605713bf + Signed-off-by: Zhang Wei + +commit 4e62041023dc3de9d98d977bb080235bc6d035e0 Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sun Nov 18 18:36:11 2007 +0100 +Date: Wed Oct 24 18:16:01 2007 +0200 - s3c24x0: Fix usb_ohci.c missing in Makefile - and usb_ohci.c warning differ in signedness + Use config_cmd_default.h instead of config_cmd_all.h Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD -commit 6073f61e078da5ddb521b56256bcc36508589883 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sun Nov 18 12:55:02 2007 +0100 +commit 56622f87857439b1c221e9deef11a9d5bb5d4308 +Author: Marian Balakowicz +Date: Wed Oct 24 01:37:36 2007 +0200 - pb1x00 board: Fix u16 status declaration when PCMCIA is defined + TQM5200: Call usb_cpu_init() during board init - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + usb_cpu_init() configures GPS USB pins, clocks, etc. and + is required for proper operation of kernel USB subsystem. + This setup was previously done in the kernel by the fixup + code which is being removed, thus low level init must be + done by U-boot now. -commit 8412d814ce8bf5570a2b747f1e7fd321097fe987 -Author: Wolfgang Denk -Date: Sun Nov 18 17:11:09 2007 +0100 + Signed-off-by: Marian Balakowicz - Fix compiler warnings for ARM systems. +commit 29c29c0267fe857e72014ce90c5d35b2ef6302bd +Author: Guennadi Liakhovetski +Date: Tue Oct 23 16:25:50 2007 +0200 - Signed-off-by: Wolfgang Denk + Fix typo in nfs.c -commit 409ecdc0bb47dd28b0af6c25ffd658d22cc36b37 -Author: Wolfgang Denk -Date: Sun Nov 18 16:36:27 2007 +0100 + An obvious typo. Originally fixed in linkstation u-boot port. - Fix compiler warnings for PPC systems. Update CHANGELOG. + Signed-off-by: Guennadi Liakhovetski - Signed-off-by: Wolfgang Denk +commit 59543fe00a4ce720ef9f5aa7fb387c6daf1c7d78 +Author: Guennadi Liakhovetski +Date: Tue Oct 23 14:35:05 2007 +0200 -commit 079c2c4fa71c0d1ebef394508df9088df8a308d3 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Sat Nov 17 11:31:10 2007 +0100 + Fix a typo in cpu/mpc824x/interrupts.c - Fix warning differ in signedness in net/net.c and net/nfs.c + Since December 2003 the timer_interrupt_cpu() function in + cpu/mpc824x/interrupts.c contains what seems to be a superfluous + parameter. Remove it. -commit 7e14fc65368cbd2861b1207453da55a4fc7b3f81 -Author: Shinya Kuribayashi -Date: Sat Nov 17 20:42:45 2007 +0900 + Signed-off-by: Guennadi Liakhovetski - gth2.c: Fix a warning on gth2 build. +commit c9e7b9b9a1700fe009678d1f9b41e6364ac5df2d +Author: Sergej Stepanov +Date: Wed Oct 17 11:13:51 2007 +0200 - gth2.c: In function 'misc_init_r': - gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness + add ft_cpu_setup(..) on mpc8260 - Signed-off-by: Shinya Kuribayashi + Add ft_cpu_setup(..)-function to adapt it for use with libfdt + based on code from mpc5xxx -commit 2309c130aa4c84b91bd874a41269c923eb61b555 + Sigend-off-by: Sergej Stepanov + -- + +commit 6abd82e19ae93c0b4d104e50165e235915ec0875 +Author: Sergej Stepanov +Date: Wed Oct 17 11:18:42 2007 +0200 + + changes for IDS8247 board support + + To get the IDS8247 board working following are done: + - FCC2 is deactivated + - FCC1 is activated + - I2C is activated + - CFI driver is activated + - Adapted for use with LIBFDT + + Signed-off-by: Sergej Stepanov + -- + +commit 3d6cb3b24add6415f86a0f013ea40f5639b90047 Author: Stefan Roese -Date: Sat Nov 17 07:58:25 2007 +0100 +Date: Sat Nov 3 12:08:28 2007 +0100 - Fix warning differ in signedness in common/cmd_scsi.c + ppc4xx: Add AMCC Kilauea/Haleakala NAND booting support + + This patch adds NAND booting support for the AMCC 405EX(r) eval boards. + Again, only one image supports both targets. Signed-off-by: Stefan Roese -commit 7e1d884b7cb602007329c517ec1c453e3a6a5d9c -Author: Shinya Kuribayashi -Date: Sat Nov 17 20:05:26 2007 +0900 +commit 8b6684a698500be9c142ec2c9f46cfc348e17f0c +Author: Haavard Skinnemoen +Date: Wed Oct 24 15:48:37 2007 +0200 - [MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker + ATSTK1002: Remove default ethernet addresses - Current trick to pick up GNU assembler minor version does not work with the - latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to - "(GNU Binutils) ". + Wolfgang is right: It's not a good idea to set up default initial + ethernet addresses for a board, even though they belong to the local + range. - $ sde-as --version |grep "GNU assembler" - GNU assembler 2.15.94 mipssde-6.02.02-20050602 - $ sde-as --version |grep "GNU assembler" |awk '{print $3}' - 2.15.94 - $ sde-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}' - 15 - $ + This will change the failure mode from "IT manager screams at you for + using duplicate ethernet addresses" to a nice error message explaining + that the ethernet address hasn't been set properly. - $ mips-linux-as --version |grep "GNU assembler" - GNU assembler (GNU Binutils) 2.18 - $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' - (GNU - $ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}' - (no output) - $ + Signed-off-by: Haavard Skinnemoen - As a result of above, you'll see many noises with such binutils: +commit e5c794e491a57d829b6d8733e2ed8368a2269abf +Author: Justin Flammia +Date: Mon Oct 29 17:40:35 2007 -0400 - make -C cpu/mips/ - /bin/sh: line 0: [: : integer expression expected - /bin/sh: line 0: [: : integer expression expected - make[1]: Entering directory `/home/skuribay/devel/u-boot.git/cpu/mips' - mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o incaip_wdt.o incaip_wdt.S - /bin/sh: line 0: [: : integer expression expected - mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o cache.o cache.S - /bin/sh: line 0: [: : integer expression expected - mips-linux-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -Wall -Wstrict-prototypes -c -o asc_serial.o asc_serial.c - /bin/sh: line 0: [: : integer expression expected + DHCP Client Fix - This patch simplifies the trick and makes it work with both versions of gas. - I also replace an expensive `awk (or gawk)' with `cut'. + This is a multi-part message in MIME format. - Signed-off-by: Shinya Kuribayashi + commit e6e505eae94ed721e123e177489291fc4544b7b8 + Author: Justin Flammia + Date: Mon Oct 29 17:19:03 2007 -0400 -commit 16664f72850846e645616da1c0fa5afcd6d15f15 -Author: Shinya Kuribayashi -Date: Sat Nov 17 20:05:26 2007 +0900 + Found a bug in the way the DHCP Request packet is built, where the IP address + that is offered by the server is bound to prematurely. This patch is a fix of + that bug where the IP address offered by the DHCP server is not used until + after the DHCP ACK from the server is received. - [MIPS] Remove useless instructions for initializing $gp. + Signed-off-by: Justin Flammia + Signed-off-by: Ben Warren - Signed-off-by: Shinya Kuribayashi +commit 5d96d40d3f36da33348e68f9ea993f383e11f997 +Author: Stefan Roese +Date: Wed Oct 31 20:58:34 2007 +0100 -commit 03c031d5660ea946c39af6e2e16267da857c609f -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:27:06 2007 +0900 + ppc4xx: Fix acadia_nand build problem - [MIPS] MIPS 4K core: Coding style cleanups + Since the cache handling functions were moved from start.S into cache.S + the acadia NAND booting Makfile needs to be adapted accordingly. - No logical changes. + Signed-off-by: Stefan Roese - Signed-off-by: Shinya Kuribayashi +commit ea2e142843533ca593fcb5cb3e1daf1b7f5e5949 +Author: Stefan Roese +Date: Wed Oct 31 20:57:11 2007 +0100 -commit f5e429d3860bba4c6ae8bead8f78349fa24491b2 -Author: Shinya Kuribayashi -Date: Sat Nov 17 20:05:20 2007 +0900 + ppc4xx: Add CONFIG_4xx_DCACHE compile options to enable cached SDRAM + + This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files + and to the Sequoia TLB init code. Now the cache can be enabled on 44x + boards by defining CONFIG_4xx_DCACHE in the board config file. This + option will disappear, when more boards use is successfully and no + more known problems exist. + + This is tested successfully on Sequoia and Katmai. The only problem that + needs to be fixed is, that USB is not working on Sequoia right now, since + it will need some cache handling code too, similar to the 4xx EMAC driver. + + Signed-off-by: Stefan Roese - [MIPS] gth2.c: Fix a warning on gth2 build. +commit 3db93b8bedd32e914b38976141b3fdf4ea3ff738 +Author: Stefan Roese +Date: Wed Oct 31 20:51:10 2007 +0100 - gth2.c: In function 'misc_init_r': - gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness + ppc4xx: Enable CPU POST test for 4xx with dcache enabled - Signed-off-by: Shinya Kuribayashi + Now with caches enabled (i- and d-cache) on 44x, we need a chance to + disable the cache for the CPU POST tests, since these tests consist + of self modifying code. This is done via the new change_tlb() function. -commit 4fbd0741b2b6441da10be93e10267122581b7079 -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:22:33 2007 +0900 + Signed-off-by: Stefan Roese - [MIPS] au1x00_eth.c: Fixed a warning on pb1000 build. +commit f71b2888b4b3c870909a0341427b2a914246f81f +Author: Stefan Roese +Date: Wed Oct 31 20:47:26 2007 +0100 - au1x00_eth.c: In function 'au1x00_miiphy_write': - au1x00_eth.c:139: warning: 'return' with no value, in function returning non-void + ppc4xx: Change 4xx POST ethernet test to handle cached memory too - Signed-off-by: Shinya Kuribayashi + This patch enables the 4xx EMAC POST driver to work too, when dcache is + enabled. -commit f01320459736f156707425cf8112f98606301aa4 -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:00:25 2007 +0900 + Signed-off-by: Stefan Roese - [MIPS] au1x00_eth.c: Fix au1x00_miiphy_{read,write} build error +commit a2685904061b35a17583d65fe47cdc2686a69eaa +Author: Stefan Roese +Date: Wed Oct 31 20:45:53 2007 +0100 - au1x00_eth.c: In function 'au1x00_enet_initialize': - au1x00_eth.c:246: error: 'au1x00_miiphy_read' undeclared (first use in this function) - au1x00_eth.c:246: error: (Each undeclared identifier is reported only once - au1x00_eth.c:246: error: for each function it appears in.) - au1x00_eth.c:246: error: 'au1x00_miiphy_write' undeclared (first use in this function) - au1x00_eth.c: In function 'au1x00_miiphy_write': - au1x00_eth.c:298: warning: 'return' with no value, in function returning non-void - make[1]: *** [au1x00_eth.o] Error 1 + ppc4xx: Remove temporary TLB entry in POST cache test only for 440 - Fixed by moving these two functions forward. + Signed-off-by: Stefan Roese - Signed-off-by: Shinya Kuribayashi +commit ff768cb168d8157c24a25016dbfbeb465e47f420 +Author: Stefan Roese +Date: Wed Oct 31 18:01:24 2007 +0100 -commit b09258c5393edd1087c5f39ae68338f16b49f8b3 -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:00:25 2007 +0900 + ppc4xx: Change 4xx ethernet driver to handle cached memory too - MAKEALL: Added missing pb1000 board + This patch enables the 4xx EMAC driver to work too, when dcache is + enabled. - Signed-off-by: Shinya Kuribayashi + Signed-off-by: Stefan Roese -commit 2e4a6e3667a1e39c0e6e99498686b15d2718b369 -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:00:24 2007 +0900 +commit 483e09a223c666269ef81d3573a6591b1046b0ef +Author: Stefan Roese +Date: Wed Oct 31 17:59:22 2007 +0100 - [MIPS] pb1000: Replace obsolete memsetup.S with lowlevel_init.S + ppc4xx: Add change_tlb function to modify I attribute of TLB(s) - Signed-off-by: Shinya Kuribayashi + This function is used to either turn cache on or off in a specific + memory area. -commit 662e5cb397249c3ea88a4c3255e9ccfc40b98d82 -Author: Shinya Kuribayashi -Date: Sat Oct 27 15:00:24 2007 +0900 + Signed-off-by: Stefan Roese - [MIPS] u-boot.lds: Cleanup __u_boot_cmd_{start,end} +commit d25dfe08fbd1220cb994e7e6b105049aa9aa8e79 +Author: Stefan Roese +Date: Wed Oct 31 17:57:52 2007 +0100 - Signed-off-by: Shinya Kuribayashi + ppc4xx: Remove cache definition from 4xx board config files -commit 5947f6999aafa7c54c1390983d264a8463dfea8e -Author: Wolfgang Denk -Date: Sat Nov 17 02:34:38 2007 +0100 + All 4xx board config files don't need the cache definitions anymore. + These are now defined in common headers. - Update CHANGELOIG, prepare for -rc4 + Signed-off-by: Stefan Roese - Signed-off-by: Wolfgang Denk +commit 9b94ac61d2176185c30adf0793e079ec30e68687 +Author: Stefan Roese +Date: Wed Oct 31 17:55:58 2007 +0100 -commit fd329e6f05bbdfe6bd71b0e09f0c76d3b0a025a5 -Author: Luotao Fu -Date: Wed Nov 14 18:58:33 2007 +0100 + ppc4xx: Rework 4xx cache support - Fix the i2c frequency and default address in rsdproto board + New cache handling functions added and all existing functions + moved from start.S into seperate cache.S. - rsdproto board support has wrong I2C frequency and wrong return value - handling. + Signed-off-by: Stefan Roese - Signed-off-by: Luotao Fu +commit 06713773da4ac3d390c63d82641eb553224b27c2 +Author: Stefan Roese +Date: Tue Oct 23 18:03:12 2007 +0200 -commit 429c180edad038f91c989cb14b478228092e7054 -Author: Wolfgang Denk -Date: Sat Nov 17 01:45:38 2007 +0100 + ppc4xx: Remove compiler warning from previous commit - powerpc: Backout relocation changes for MPC5121, too. + Signed-off-by: Stefan Roese - Apply Grant Likely's backout to MPC5121 code, too. +commit 6fa397df67c0f269e4528bf181a6e8c88f9723f9 +Author: Stefan Roese +Date: Tue Oct 23 14:40:30 2007 +0200 - Pointed out by Rafal Jaworowski + ppc4xx: Remove temporary TLB entry in POST cache test - Signed-off-by: Wolfgang Denk + Signed-off-by: Stefan Roese -commit 1c3dd43338a077165e7e0309cb3994e65d2bdbf8 -Author: Grant Likely -Date: Tue Nov 13 22:18:33 2007 -0700 +commit 1338e6a81834099ba19733b69aafd8ef5f098094 +Author: Stefan Roese +Date: Tue Oct 23 14:05:08 2007 +0200 - powerpc: Backout relocation changes. + ppc4xx: Change autonegotiation timeout from 4 to 5 seconds - Ugh. I *hate* to back this change out, but these compiler flags don't - work for relocation on all versions of GCC. I've not been able to - reproduce the environment in my setup (and hence, not been able to - find a combination that *does* work), so I've got no choice but to go - back to the old gcc flags and linker script. + I lately noticed, that newer 4xx board with GBit support sometimes don't + finish link autonegotiation in 4 seconds. Changing this timeout to 5 + seconds seems fine here. - Signed-off-by: Grant Likely + Signed-off-by: Stefan Roese -commit 5c15010efad980ad5498cc565fc1ed70df2f52b4 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Tue Nov 13 09:11:05 2007 +0100 +commit 2d83476a4c1c9911d158a3f8a4312d354bc1bdb7 +Author: Stefan Roese +Date: Tue Oct 23 14:03:17 2007 +0200 - Fixed mips_io_port_base build errors. + ppc4xx: Change 4xx_enet & miiphy to use out_be32() and friends - This patch has been sent on: - - 29 Sep 2007 + This patch changes all in32/out32 calls to use the recommended in_be32/ + out_be32 macros instead. - Although mips_io_port_base is currently a part of IDE command, it is quite - fundamental for MIPS I/O port access such as in[bwl] and out[bwl]. So move - it to MIPS general part, and introduce `set_io_port_base()' from Linux. + Signed-off-by: Stefan Roese - This patch is triggered by multiple definition of `mips_io_port_base' build - error on gth2 (and tb0229 also needs this fix.) +commit 7d47cee2cc57f907380f2c06f5b6c683d03e423a +Author: Stefan Roese +Date: Thu Oct 25 12:24:59 2007 +0200 - board/gth2/libgth2.a(gth2.o): In function `log_serial_char': - /home/skuribay/devel/u-boot.git/board/gth2/gth2.c:47: multiple definition of `mips_io_port_base' - common/libcommon.a(cmd_ide.o):/home/skuribay/devel/u-boot.git/common/cmd_ide.c:712: first defined here - make: *** [u-boot] Error 1 + ppc4xx: Fix POST ethernet test for Haleakala - Signed-off-by: Shinya Kuribayashi - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + The POST ethernet test needed to be changed to dynamically determine + the count of ethernet devices. This code is cloned from the 4xx + ethernet driver. -commit 6ecbb7a3fa9b0940ed33e490d195d4b6830b2422 -Author: Wolfgang Denk -Date: Sat Nov 17 01:30:40 2007 +0100 + Signed-off-by: Stefan Roese - Fix a bug in the slave serial programming mode for the Xilinx - Spartan2/3 FPGAs. The old code used "< 0" on a "char" type to test if - the most significant bit was set, which did not work on any - architecture where "char" defaulted to be an unsigned type. +commit f10493c6d77a1e07a6c2ff4d772937a5e7359d6a +Author: Stefan Roese +Date: Tue Oct 23 11:31:05 2007 +0200 - Based on a patch by Angelos Manousaridis + ppc4xx: Correct UART input clock calculation and passing to fdt - Signed-off-by: Wolfgang Denk + We now use a value in the gd (global data) structure for the UART input + frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely + in get_sys_info(). -commit d08b7233bc252faad8339e7ca0ddfd62fa79903c -Author: Jon Loeliger -Date: Thu Nov 1 12:23:29 2007 -0500 + Signed-off-by: Stefan Roese - 86xx: Fix broken variable reference when #def DEBUGing. +commit 353f2688b4e0fc7b969bc70a02be4b40bf0dd124 +Author: Stefan Roese +Date: Tue Oct 23 10:10:08 2007 +0200 - Sometimes you can't reference the DDR2 controller variables. + ppc4xx: Add initial AMCC Haleakala PPC405EXr eval board support - Signed-off-by: Jon Loeliger + The Haleakala is nearly identical with the Kilauea eval board. The only + difference is that the 405EXr only supports one EMAC and one PCIe + interface. This patch adds support for the Haleakala board by using + the identical image for Kilauea and Haleakala. The distinction is done + by comparing the PVR. -commit f9d9164d9c6b5a7f0393fd8d7e246b8a0326bc19 -Author: Jason Jin -Date: Fri Oct 26 18:32:00 2007 +0800 + Signed-off-by: Stefan Roese - make 8610 board use pixis reset +commit 9f798766aa85e62eb8fa8c721e148df609b78137 +Author: Eugene O'Brien +Date: Tue Oct 23 08:29:10 2007 +0200 - Signed-off-by: Jason Jin + ppc4xx: Fixed offset of refresh rate type for Bamboo on-board DDR SDRAM -commit db74b3c1c9481a6bffbf8cd445e5bcbf6908e836 -Author: Jason Jin -Date: Mon Oct 29 19:26:21 2007 +0800 + This patch also adds a note to the fixed DDR setup for Bamboo NAND booting: - Unify pixis_reset altbank across board families + Note: + As found out by Eugene O'Brien , the fixed + DDR setup has problems (U-Boot crashes randomly upon TFTP), when the DIMM + modules are still plugged in. So it is recommended to remove the DIMM + modules while using the NAND booting code with the fixed SDRAM setup! - Basically, refactor the CFG_PIXIS_VBOOT_MASK values - into the separate board config files. + Signed-off-by: Eugene O'Brien + Signed-off-by: Stefan Roese - Signed-off-by: Jason Jin - Signed-off-by: Jon Loeliger +commit afe9fa59cb63b4f9d16bf01c93eb212f25a38c2a +Author: Stefan Roese +Date: Mon Oct 22 16:24:44 2007 +0200 -commit 64bf555465c7926be13e1046ac0d0f05ac72829c -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Wed Nov 7 08:19:21 2007 +0100 + ppc4xx: Add SNTP support to AMCC Katmai, Kilauea & Makalu boards - Fix warning: pointer targets in assignment differ in signedness + Signed-off-by: Stefan Roese - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD +commit 3248f63ad89cb031491edb7016587fe6e9a238b9 +Author: Stefan Roese +Date: Mon Oct 22 16:22:40 2007 +0200 -commit 7a60ee7c6248a958c5757d3660a1702723a2786d -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Wed Nov 7 08:19:19 2007 +0100 + ppc4xx: Rework of 4xx serial driver (4) - Fix warning differ in signedness in common/cmd_ide.c + Change 4xx_uart.c: - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + - Use in_8/out_8 macros instead of in8/out8 + - No need for UART_BASE marco anymore, now really handled via function + parameter + - serial_init_common() introduced + - Further coding style cleanup -commit 4d4faae65e115e327425cd514c1a35146a85166b -Author: Grant Likely -Date: Mon Sep 24 09:05:31 2007 -0600 + Signed-off-by: Stefan Roese - Group PCI and PCMCIA drivers in drivers/Makefile +commit e61cb8163a66b8a135696ae232e2bead1ce0a049 +Author: Stefan Roese +Date: Mon Oct 22 15:45:49 2007 +0200 - Signed-off-by: Grant Likely + ppc4xx: Rework of 4xx serial driver (3) -commit 5798f87dc10a496d79d3177b9f5a76488987fd35 -Author: Grant Likely -Date: Mon Sep 24 09:05:31 2007 -0600 + Change all linker scripts to reference the changed driver name iop480_uart.o. - Group block/flash drivers in drivers/Makefile + Signed-off-by: Stefan Roese - Signed-off-by: Grant Likely +commit 882ae41274921f9016131806bdeb27e19606f47a +Author: Stefan Roese +Date: Mon Oct 22 15:44:39 2007 +0200 -commit df58c81551700f058b44cacf55a7997fa63bfe0a -Author: Grant Likely -Date: Mon Sep 24 09:05:31 2007 -0600 + ppc4xx: Rework of 4xx serial driver (2) - Group USB drivers in drivers/Makefile + Change all linker scripts to reference the changed driver name 4xx_uart.o. - Signed-off-by: Grant Likely + Note: In most cased all these explicit referencing of these object files + in the linker scripts is not neccessary. Only for manually embedded + environment into the U-Boot image, which is not done is most cases. -commit 5dbb6ed622e539b0c8493ef7e578d3a533181d29 -Author: Grant Likely -Date: Mon Sep 24 09:05:30 2007 -0600 + Signed-off-by: Stefan Roese - Group i2c drivers in drivers/Makefile +commit ad31e40bed042cb670d0036fea96435007afb838 +Author: Stefan Roese +Date: Mon Oct 22 15:09:59 2007 +0200 - Signed-off-by: Grant Likely + ppc4xx: Rework of 4xx serial driver (1) -commit ec00c76de0e5971273905998d62d6bb119324218 -Author: Grant Likely -Date: Mon Sep 24 09:05:30 2007 -0600 + This patch starts the rework of the PPC4xx serial driver. First we split + the file into two seperate files, one 4xx_uart.c with the 405/440 UART + handling code and the other one iop480_uart.c with the UART code for the + PLX-Tech IOP480 PPC (PPC403 based). - Group console drivers in drivers/Makefile + Signed-off-by: Stefan Roese - Signed-off-by: Grant Likely +commit 764e7417ee5f6e25b1715720e7d7dd3487109385 +Author: Stefan Roese +Date: Mon Oct 22 10:30:38 2007 +0200 -commit 754f230aa01b8c789fc31f8013c2487954073300 -Author: Grant Likely -Date: Mon Sep 24 09:05:30 2007 -0600 + ppc4xx: Correct UART input clock calculation and passing to fdt - Group network drivers in drivers/Makefile + Signed-off-by: Stefan Roese - Signed-off-by: Grant Likely +commit 211ea91ac6c225bec7e668a03d0ba7d7310679fa +Author: Stefan Roese +Date: Mon Oct 22 07:34:34 2007 +0200 -commit f0037c56b0d12cd46215124667b9f83d60ef9391 -Author: Grant Likely -Date: Mon Sep 24 09:05:30 2007 -0600 + ppc4xx: Add initial AMCC Makalu 405EX support - Build: split COBJS value into multiple lines + Signed-off-by: Stefan Roese - This change is in preparation for condtitionial compile support in the - build system. By spliting them all into seperate lines now, subsequent - patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_) += ' will - be less invasive and easier to review +commit fa8aea20456e6f1dba43f46bcc72024dd9499998 +Author: Stefan Roese +Date: Mon Oct 22 07:33:52 2007 +0200 - Signed-off-by: Grant Likely + ppc4xx: Add freqUART to CPU speed detection -commit 1b4aaffe4fb2a5e95d9111a5d94fd1f89215dce4 -Author: Grant Likely -Date: Mon Sep 24 09:05:30 2007 -0600 + This value is needed later for the device tree configuration of + the uart clock. - Add .gitignore files + Signed-off-by: Stefan Roese - Signed-off-by: Grant Likely - Acked-by: Kim Phillips +commit 837c730b4d7c6b1ddf3d1e247cb4445005d9bf0d +Author: Stefan Roese +Date: Sun Oct 21 14:26:29 2007 +0200 -commit 955413f35f054a82e40042f1dbcf501c6a05719b -Author: Grant Likely -Date: Thu Nov 15 08:27:52 2007 -0700 + ppc: Small Kilauea cleanup of config file - Revert "Correct relocation fixup for mpc5xx" + Signed-off-by: Stefan Roese - This reverts commit 3649cd99ba815b6601868735765602f00ef3692b. - Signed-off-by: Grant Likely +commit 758c037aeead34b49631b8da3a90b1bba14c0410 +Author: Stefan Roese +Date: Sun Oct 21 08:16:12 2007 +0200 -commit e15633888a058aacb31a62d2cf1278e1e4c236ab -Author: Grant Likely -Date: Thu Nov 15 08:24:32 2007 -0700 + rtc: Add Xicor/Intersil X1205 RTC support - Revert "Correct fixup relocation for MPC5xxx" + This patch adds support for the Xicor/Intersil X1205 RTC used on the + AMCC Makalu eval board. This driver is basically cloned from the Linux + driver version (2.6.23). - This reverts commit 6f7576b20ecf0d040c3ac3b032b5cbc860e38a90. - Signed-off-by: Grant Likely + This patch also introduces the Linux bcd.h header for the BCD2BIN/ + BIN2BCD conversions. In the future some of the other U-Boot RTC driver + should be converted to also use this header instead of implementing + their own local copy of these functions/macros. -commit 139365fbe566d0fc619a1ed04452ec5388f0cef8 -Author: Grant Likely -Date: Thu Nov 15 08:21:04 2007 -0700 + Signed-off-by: Stefan Roese - Revert "Correct fixup relocation for mpc8220" +commit 087dfdb79b5fd1ab99a26990c62a732c01a8c7f6 +Author: Stefan Roese +Date: Sun Oct 21 08:12:41 2007 +0200 - This reverts commit a85dd254c0577fca13627c46e93fc2ad4c4f1f00. - Signed-off-by: Grant Likely + ppc4xx: Consolidate some of the 405 and 440 macros/structs into 4xx -commit 70922342369e5e39b286fe21e768a239ca07a514 -Author: Grant Likely -Date: Thu Nov 15 08:20:57 2007 -0700 + This patch moves some common 4xx macros and the PPC405_SYS_INFO/ + PPC440_SYS_INFO structure into the common ppc4xx.h header. - Revert "Correct fixup relocation for mpc824x" + Lot's of other macros are good candidates to be consolidated this way + in the future. - This reverts commit f3a52fe05923935db86985daf9438e2f70ac39aa. - Signed-off-by: Grant Likely + Signed-off-by: Stefan Roese -commit 96279ab4cad60cb5972aa934fbe4845ac02cc75a -Author: Grant Likely -Date: Thu Nov 15 08:20:50 2007 -0700 +commit 770c7af5800f598d22730d1f4b70f16c9b33512e +Author: Stefan Roese +Date: Sun Oct 21 08:05:18 2007 +0200 - Revert "Correct fixup relocation for mpc8260" + ppc4xx: Fix size setup in Kilauea DDR2 init routine - This reverts commit 5af61b2f4b838a05f79be274f3e5a66edd2d9c96. - Signed-off-by: Grant Likely + The size was initilized wrong. Instead of 256MB, the DDR2 controller + was setup to 512MB. Now the correct values is used. -commit 928fe33b24cdf382a8dc8687fed24b1961cdb5d6 -Author: Grant Likely -Date: Thu Nov 15 08:20:43 2007 -0700 + This patch also does a little cleanup and adds a comment here. - Revert "Correct fixup relocation for mpc83xx" + Signed-off-by: Stefan Roese - This reverts commit 057004f4a4863554d56cc56268bfa7c7d9738e27. - Signed-off-by: Grant Likely +commit f6ba9b56607d4b27550301c7c7f6b55b654fd62a +Author: Eugene O'Brien +Date: Thu Oct 18 17:29:04 2007 +0200 -commit c93945e8f9e300860d2bf73a2549ce5794f8bd00 -Author: Grant Likely -Date: Thu Nov 15 08:20:25 2007 -0700 + ppc4xx: Define CONFIG_BOOKE for all PPC440 based processors - Revert "[MPC512x] Correct fixup relocation" + CONFIG_BOOKE must be defined for PPC440 processors so that the proper SPR + number is used to access system registers. - This reverts commit 8d17979d0359492a822a0a409d26e3a3549b4cd4. - Signed-off-by: Grant Likely + Signed-off-by: Eugene O'Brien + Signed-off-by: Stefan Roese -commit 54fd6c93c28a0a45352fff5dd92673401ff563f2 +commit c36c68160333ac5fe41ec3db12a728b7075b3912 Author: Stefan Roese -Date: Tue Nov 13 08:18:20 2007 +0100 +Date: Thu Oct 18 07:42:27 2007 +0200 - ppc4xx: lwmon5: Change PHY reset sequence for PHY MDIO address latching + ppc4xx: Change inbound PCIe location for endpoint tests on Katmai - Signed-off-by: Stefan Roese + On Yucca & Katmai, the inbound memory map pointed to 0x4.0000.0000, which + is the internal SRAM. Since I now ported and tested this endpoint mode + on Kilauea successfully to map to 0 (SDRAM), I also changed this for + Katmai. -commit 1ce55151c85d068f70317a8d65c61058b891afb4 -Author: Heiko Schocher -Date: Tue Nov 13 07:50:29 2007 +0100 + Yucca will stay at internal SRAM for now. Not sure if somebody relies on + this setup. - [UC101] SRAM now with 2 MB working. + Signed-off-by: Stefan Roese - Signed-off-by: Heiko Schocher +commit 5cb4af4791f61843432155142b6cfac901f66c10 +Author: Stefan Roese +Date: Thu Oct 18 07:39:38 2007 +0200 -commit 8d737a28152ec12873f8544cca1fb39a49e5e693 -Author: TsiChungLiew -Date: Thu Nov 8 12:50:18 2007 -0600 + ppc4xx: Add PCIe endpoint support on Kilauea (405EX) - ColdFire: MCF5329 - Remove reset registers from CCM + This patch adds endpoint support for the AMCC Kilauea eval board. It can + be tested by connecting a reworked PCIe cable (only 1x lane singles + connected) to another root-complex. - Signed-off-by: TsiChungLiew + In this test setup, a 64MB inbound window is configured at BAR0 which maps + to 0 on the PLB side. So accessing this BAR0 from the root-complex will + access the first 64MB of the SDRAM on the PPC side. -commit 7d7cdea769a60b0a6e4c18bef7f9d648fd14b8d7 -Author: TsiChungLiew -Date: Thu Nov 8 12:31:11 2007 -0600 + Signed-off-by: Stefan Roese - ColdFire: MCF5329 - Add Reset structure to immap_5329.h +commit d4cb2d17946466740afeb195a57d6cb290bf4cc0 +Author: Stefan Roese +Date: Sat Oct 13 16:43:23 2007 +0200 - Signed-off-by: TsiChungLiew + ppc4xx: Dynamic configuration of 4xx PCIe mode as root or endpoint mode -commit 09b26cf00d76d75fdf7fdc4b13e4dd929743bc21 -Author: TsiChungLiew -Date: Thu Nov 8 12:19:01 2007 -0600 + This patch adds support for dynamic configuration of PCIe ports for the + AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe + boards Yucca & Katmai and the 405EX board Kilauea. - ColdFire: MCF5329 - revert include/asm-m68k/m5329.h file mode + This dynamic configuration is done via the "pcie_mode" environement + variable. This variable can be set to "EP" or "RP" for endpoint or + rootpoint mode. Multiple values can be joined via the ":" delimiter. + Here an example: - Signed-off-by: TsiChungLiew + pcie_mode=RP:EP:EP -commit 225a24b5e062ad94627424508ae814f51dbe1a34 -Author: TsiChungLiew -Date: Wed Nov 7 18:00:54 2007 -0600 + This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2 + as endpoint. - ColdFire: MCF5445x - Update correct RAMBAR and missing linker files + Per default Yucca will be configured as: + pcie_mode=RP:EP:EP - Signed-off-by: TsiChungLiew + Per default Katmai will be configured as: + pcie_mode=RP:RP:REP -commit 248c7c14835f34d5d910b45e5600050e58ca6cab -Author: TsiChungLiew -Date: Wed Nov 7 17:56:15 2007 -0600 + Per default Kilauea will be configured as: + pcie_mode=RP:RP - ColdFire: MCF532x - Update do_reset() using core reset + Signed-off-by: Tirumala R Marri + Signed-off-by: Stefan Roese - Signed-off-by: TsiChungLiew +commit fd671802b67a0ef37a06124fa2ce85f00aa22c6f +Author: Stefan Roese +Date: Thu Oct 11 11:15:59 2007 +0200 -commit d9240a5f827eb3b476a6ba2938d01f1a9e7688f4 -Author: TsiChungLiew -Date: Wed Nov 7 17:51:00 2007 -0600 + ppc4xx: Enable device tree support (fdt) on Kilauea per default - ColdFire: Update cpu flag for 4.2-xx compiler + This patch enables the fdt support on the AMCC Kilauea eval board. + Additionally now EBC ranges fdt fixup is included to support NOR + FLASH mapping via the Linux physmap_of driver. - Signed-off-by: TsiChungLiew + This Kilauea port now support booting arch/ppc and arch/powerpc + Linux kernels. The default environment "net_nfs" is for arch/ppc + and "net_nfs_fdt" is for arch/powerpc. In the long run, arch/ppc + support will be removed. -commit 1f103105a3746ab12279b63b8c1d372c0ce2cc58 -Author: Roy Zang -Date: Mon Nov 5 17:39:24 2007 +0800 + Signed-off-by: Stefan Roese - Implement general ULi 526x Ethernet driver support in U-boot +commit 4994ffd890b9d95d807387a9b7bd8a4803ee406e +Author: Stefan Roese +Date: Thu Oct 11 11:11:45 2007 +0200 - This patch implements general ULi 526x Ethernet driver. - Until now, it is the only native Ethernet port on - MPC8610HPCD board, but it could be used on other boards - with ULi 526x Ethernet port as well. + ppc4xx: Add additional debug info to 4xx fdt support - Signed-off-by: Roy Zang - Signed-off-by: Zhang Wei - Acked-by: Jon Loeliger - Signed-off-by: Ben Warren + Signed-off-by: Stefan Roese -commit 71bc6e6474fea8ef481b9b45d1edd7ad1f6dfbbd -Author: Larry Johnson -Date: Thu Nov 1 08:46:50 2007 -0500 +commit db3232ddb058d0ed0bc31f7c5c296748a1afac67 +Author: Stefan Roese +Date: Fri Oct 5 21:28:58 2007 +0200 - NET: Add Ethernet 1000BASE-X support for PPC4xx + ppc4xx: Fix small merge problems with CPCI440 and Acadia boards - This patch adds support for 1000BASE-X to functions "miiphy_speed ()" and - "miiphy_duplex()". It also adds function "miiphy_is_1000base_x ()", which - returns non-zero iff the PHY registers are configured for 1000BASE-X. The - "mii info" command is modified to distinguish between 1000BASE-T and -X. + Signed-off-by: Stefan Roese - Signed-off-by: Larry Johnson - Signed-off-by: Ben Warren +commit 1941cce71b1ae975602854045061e82f94ecd012 +Author: Stefan Roese +Date: Fri Oct 5 17:35:10 2007 +0200 -commit 298035df4948b113d29ac0e694717d34b95bc5dc -Author: Larry Johnson -Date: Wed Oct 31 11:21:29 2007 -0500 + ppc4xx: Fix small merge problem in 4xx_enet.c - NET: Cosmetic changes + Signed-off-by: Stefan Roese - Signed-off-by: Larry Johnson - Signed-off-by: Ben Warren +commit 566806ca1a1bf4d895daaf0b2ba5494abbffebaf +Author: Stefan Roese +Date: Fri Oct 5 17:11:30 2007 +0200 -commit 992742a5b09d9040adbd156fb90756af66ade310 -Author: Wolfgang Denk -Date: Sat Nov 3 23:09:27 2007 +0100 + ppc4xx: Add initial AMCC Kilauea 405EX support - Cleanup coding style; update CHANGELOG + Signed-off-by: Stefan Roese - Signed-off-by: Wolfgang Denk +commit dbbd125721aea6645fdb962f36bd41f59e272f9d +Author: Stefan Roese +Date: Fri Oct 5 17:10:59 2007 +0200 -commit e881cb563e32f45832b7b6db77bdcd017adcbb41 -Author: Bruce Adler -Date: Fri Nov 2 13:15:42 2007 -0700 + ppc4xx: Add PPC405EX support - fix wording in README + Signed-off-by: Stefan Roese - Changed the wording to properly describe the shadowing - of the environment from ROM to RAM +commit 1d7b874e9c9a7c66f5d8da9ec78a3733765d3e31 +Author: Stefan Roese +Date: Fri Oct 5 17:09:36 2007 +0200 - Signed-off-by: Bruce Adler + ppc4xx: Cleanup of 4xx PCI and PCIe support (renaming) -commit ad845beef06245426c57b53dcdc01b7dc70e0d45 -Author: Shinya Kuribayashi -Date: Wed Oct 31 02:18:15 2007 +0900 + Signed-off-by: Stefan Roese - blackfin: Move `-D__BLACKFIN__' to $(ARCH)_config.mk +commit 4f14ed6230b9c109aac9a6fb878497dabd44c2db +Author: Stefan Roese +Date: Fri Oct 5 17:07:50 2007 +0200 - Signed-off-by: Shinya Kuribayashi + ppc4xx: Add initial fdt support to 4xx (first needed on 405EX) -commit ec22755799466c8a103664bb3a5e647bf9c238f4 -Author: Vlad Lungu -Date: Thu Oct 25 16:08:14 2007 +0300 + Signed-off-by: Stefan Roese - Trimmed some variables in ne2000.c +commit a424a8bb2924b90724b944165d3141f1fa8dfe5b +Author: Stefan Roese +Date: Fri Oct 5 17:04:57 2007 +0200 - Signed-off-by: Vlad Lungu + POST: Add 405EX support to 4xx UART POST test -commit eb6f214d3644b2a77968c176ed36dcf858cfe7e0 -Author: Zhang Wei -Date: Thu Oct 25 17:51:27 2007 +0800 + Signed-off-by: Stefan Roese - Fix the issue of usb_kbd driver missing the scan code of key 'z'. +commit 4f2e92c11f6e2392fc8187829211a5ca7f0c1e12 +Author: Stefan Roese +Date: Fri Oct 5 15:10:02 2007 +0200 - The scan code of the key 'z' is 0x1d, which should be handled. + DTT: Prepare DS1775 driver for use of different I2C addresses - The change has be tested on NOVATEK USB keyboard and ULI PCI OHCI - controller. + Signed-off-by: Stefan Roese - Signed-off-by: Zhang Wei +commit 19e93b1e16d267220440d827b920fbad8abfa70f +Author: Stefan Roese +Date: Fri Oct 5 14:23:43 2007 +0200 -commit bbf4796f6498fbade56d56eff3a0a49b299d93e5 -Author: Zhang Wei -Date: Thu Oct 25 17:30:04 2007 +0800 + ppc4xx: 4xx_pcie: Change PCIe status output to match common style - Fix USB support issue for MPC8641HPCN board. + Signed-off-by: Stefan Roese - The configuration file has already enabled USB, but it - missed definition of CFG_OHCI_SWAP_REG_ACCESS, the USB - on MPC8641HPCN can not work because of the wrong USB - register endian. +commit ff68f66bcb0da847845aa2fac11eba6c25938c99 +Author: Stefan Roese +Date: Fri Oct 5 09:22:33 2007 +0200 - And add the USB command to U-Boot commands list. + ppc4xx: 4xx_pcie: Disable debug output as default - Signed-off-by: Zhang Wei + Signed-off-by: Stefan Roese -commit 4e62041023dc3de9d98d977bb080235bc6d035e0 -Author: Jean-Christophe PLAGNIOL-VILLARD -Date: Wed Oct 24 18:16:01 2007 +0200 +commit 97923770cb52b64d69eec958a11b2eda8d46e0f7 +Author: Stefan Roese +Date: Fri Oct 5 09:18:23 2007 +0200 - Use config_cmd_default.h instead of config_cmd_all.h + ppc4xx: 4xx_pcie: More general cleanup and 405EX PCIe support added - Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Stefan Roese -commit 56622f87857439b1c221e9deef11a9d5bb5d4308 -Author: Marian Balakowicz -Date: Wed Oct 24 01:37:36 2007 +0200 +commit 4dbee8a90df613eb517aadbecebd70f168913d30 +Author: Stefan Roese +Date: Fri Oct 5 07:57:20 2007 +0200 - TQM5200: Call usb_cpu_init() during board init + ppc4xx: 4xx_pcie: Change CFG_PCIE_MEMSIZE to 128MB on Yucca & Katmai - usb_cpu_init() configures GPS USB pins, clocks, etc. and - is required for proper operation of kernel USB subsystem. - This setup was previously done in the kernel by the fixup - code which is being removed, thus low level init must be - done by U-boot now. + 128MB seems to be the smallest possible value for the memory size + for on PCIe port. With this change now the BAR's of the PCIe cards + are accessible under U-Boot. - Signed-off-by: Marian Balakowicz + One big note: This only works for PCIe port 0 & 1. For port 2 this + currently doesn't work, since the base address is now 0xc0000000 + (0xb0000000 + 2 * 0x08000000), and this is already occupied by + CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean + to change the base addresses completely and this change would have + too much impact right now. -commit 29c29c0267fe857e72014ce90c5d35b2ef6302bd -Author: Guennadi Liakhovetski -Date: Tue Oct 23 16:25:50 2007 +0200 + This patch adds debug output to the 4xx pcie driver too. - Fix typo in nfs.c + Signed-off-by: Stefan Roese - An obvious typo. Originally fixed in linkstation u-boot port. +commit 6d95289281ed2958ebf76d2b55f86bbd88591fd2 +Author: Stefan Roese +Date: Wed Oct 3 21:16:32 2007 +0200 - Signed-off-by: Guennadi Liakhovetski + ppc4xx: 4xx_pcie: Fix problem with SDRN access using port number as idx -commit 59543fe00a4ce720ef9f5aa7fb387c6daf1c7d78 -Author: Guennadi Liakhovetski -Date: Tue Oct 23 14:35:05 2007 +0200 + Signed-off-by: Stefan Roese - Fix a typo in cpu/mpc824x/interrupts.c +commit 3048bcbf0bad262378c5af68f2bf6778fb7d829a +Author: Stefan Roese +Date: Wed Oct 3 15:01:02 2007 +0200 - Since December 2003 the timer_interrupt_cpu() function in - cpu/mpc824x/interrupts.c contains what seems to be a superfluous - parameter. Remove it. + ppc4xx: Rename 405gp_pci to 4xx_pci since its used on all 4xx platforms - Signed-off-by: Guennadi Liakhovetski + These files were introduced with the IBM 405GP but are currently used on all + 4xx PPC platforms. So the name doesn't match the content anymore. This patch + renames the files to 4xx_pci.c/h. -commit c9e7b9b9a1700fe009678d1f9b41e6364ac5df2d -Author: Sergej Stepanov -Date: Wed Oct 17 11:13:51 2007 +0200 + Signed-off-by: Stefan Roese - add ft_cpu_setup(..) on mpc8260 +commit 94276eb0a7a35b9e8c053d589ae225b0f017a237 +Author: Stefan Roese +Date: Wed Oct 3 14:14:58 2007 +0200 - Add ft_cpu_setup(..)-function to adapt it for use with libfdt - based on code from mpc5xxx + ppc4xx: Add a comment for 405EX PCIe endpoint configuration - Sigend-off-by: Sergej Stepanov - -- + Signed-off-by: Stefan Roese -commit 6abd82e19ae93c0b4d104e50165e235915ec0875 -Author: Sergej Stepanov -Date: Wed Oct 17 11:18:42 2007 +0200 +commit 03d344bb6a5f082ea10ec9d753558ea7dfd1c626 +Author: Stefan Roese +Date: Wed Oct 3 10:38:09 2007 +0200 - changes for IDS8247 board support + ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (3) - To get the IDS8247 board working following are done: - - FCC2 is deactivated - - FCC1 is activated - - I2C is activated - - CFI driver is activated - - Adapted for use with LIBFDT + (3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access + the SDR registers of the PCIe ports. This makes the overall design + clearer, since it removed a lot of switch statements which are not + needed anymore. - Signed-off-by: Sergej Stepanov - -- + Also, the functions ppc4xx_init_pcie_rootport() and + ppc4xx_init_pcie_entport() are merged into a single function + ppc4xx_init_pcie_port(), since most of the code was duplicated. + This makes maintainance and porting to other 4xx platforms + easier. -commit 8b6684a698500be9c142ec2c9f46cfc348e17f0c -Author: Haavard Skinnemoen -Date: Wed Oct 24 15:48:37 2007 +0200 + Signed-off-by: Stefan Roese - ATSTK1002: Remove default ethernet addresses +commit 026f71106871f31d17d0ea0db9a7547ff92934bc +Author: Stefan Roese +Date: Wed Oct 3 07:48:09 2007 +0200 - Wolfgang is right: It's not a good idea to set up default initial - ethernet addresses for a board, even though they belong to the local - range. + ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (2) - This will change the failure mode from "IT manager screams at you for - using duplicate ethernet addresses" to a nice error message explaining - that the ethernet address hasn't been set properly. + This patch is the first patch of a series to make the 440SPe PCIe code + usable on different 4xx PPC platforms. In preperation for the new 405EX + which is also equipped with PCIe interfaces. - Signed-off-by: Haavard Skinnemoen + (2) This patch renames the functions from 440spe_ to 4xx_ with a + little additional cleanup -commit e5c794e491a57d829b6d8733e2ed8368a2269abf -Author: Justin Flammia -Date: Mon Oct 29 17:40:35 2007 -0400 + Signed-off-by: Stefan Roese - DHCP Client Fix +commit c7c6da23028f146d912514b95aefa3da7cf37699 +Author: Stefan Roese +Date: Wed Oct 3 07:34:10 2007 +0200 - This is a multi-part message in MIME format. + ppc4xx: Make 440SPe PCIe code more generic to use on different 4xx PPCs (1) - commit e6e505eae94ed721e123e177489291fc4544b7b8 - Author: Justin Flammia - Date: Mon Oct 29 17:19:03 2007 -0400 + This patch is the first patch of a series to make the 440SPe PCIe code + usable on different 4xx PPC platforms. In preperation for the new 405EX + which is also equipped with PCIe interfaces. - Found a bug in the way the DHCP Request packet is built, where the IP address - that is offered by the server is bound to prematurely. This patch is a fix of - that bug where the IP address offered by the DHCP server is not used until - after the DHCP ACK from the server is received. + (1) This patch renames the files from 440spe_pcie to 4xx_pcie - Signed-off-by: Justin Flammia - Signed-off-by: Ben Warren + Signed-off-by: Stefan Roese commit 31548249decf18a6b877a18436b6139dd483fe4a Author: Justin Flammia @@ -2232,6 +4748,39 @@ Date: Wed Oct 17 15:40:19 2007 +0200 Signed-off-by: Stefan Roese +commit 3c89d75409eb26639d36dfa11d4ee3d8b962dc3c +Author: Jon Loeliger +Date: Tue Oct 16 15:27:43 2007 -0500 + + Initial mpc8610hpcd Makefile files. + + Signed-off-by: Ed Swarthout + Signed-off-by: Mahesh Jade + Signed-off-by: Jason Jin + Signed-off-by: Jon Loeliger + +commit 9553df86d3a319c3a1a7cde7e4edd6eeb5aa64c7 +Author: Jon Loeliger +Date: Tue Oct 16 15:26:51 2007 -0500 + + Initial mpc8610hpcd cpu/, README and include/ files. + + Signed-off-by: Ed Swarthout + Signed-off-by: Mahesh Jade + Signed-off-by: Jason Jin + Signed-off-by: Jon Loeliger + +commit 3dd2db53ceb0dff80f25c2a07f83f29b907b403e +Author: Jon Loeliger +Date: Tue Oct 16 13:54:01 2007 -0500 + + Initial mpc8610hpcd board files. + + Signed-off-by: Ed Swarthout + Signed-off-by: Mahesh Jade + Signed-off-by: Jason Jin + Signed-off-by: Jon Loeliger + commit 7ee6ba1a056e4061ab4cfde30127e332e7957afd Author: runet@innovsys.com Date: Tue Oct 16 14:50:40 2007 -0500 diff --git a/board/apollon/lowlevel_init.S b/board/apollon/lowlevel_init.S index f254428c9ca..8381feae086 100644 --- a/board/apollon/lowlevel_init.S +++ b/board/apollon/lowlevel_init.S @@ -31,16 +31,16 @@ #include #include "mem.h" -#define APOLLON_CS0_BASE 0x00000000 +#define APOLLON_CS0_BASE 0x00000000 #ifdef PRCM_CONFIG_I -#define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 -#define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 -#define SDRC_RFR_CTRL_0_VAL 0x00044C01 +#define SDRC_ACTIM_CTRLA_0_VAL 0x7BA35907 +#define SDRC_ACTIM_CTRLB_0_VAL 0x00000013 +#define SDRC_RFR_CTRL_0_VAL 0x00044C01 #elif defined(PRCM_CONFIG_II) -#define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 -#define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C -#define SDRC_RFR_CTRL_0_VAL 0x00030001 +#define SDRC_ACTIM_CTRLA_0_VAL 0x4A59B485 +#define SDRC_ACTIM_CTRLB_0_VAL 0x0000000C +#define SDRC_RFR_CTRL_0_VAL 0x00030001 #endif #define SDRAM_BASE_ADDRESS 0x80008000 @@ -66,100 +66,100 @@ flash_setup: ldr r1, =WD_UNLOCK2 str r1, [r0, #WSPR] - /* Pin muxing for SDRC */ - mov r1, #0x00 - ldr r0, =0x480000A1 /* ball C12, mode 0 */ - strb r1, [r0] - - ldr r0, =0x48000032 /* ball D11, mode 0 */ - strb r1, [r0] - - ldr r0, =0x480000A3 /* ball B13, mode 0 */ - strb r1, [r0] + /* Pin muxing for SDRC */ + mov r1, #0x00 + ldr r0, =0x480000A1 /* ball C12, mode 0 */ + strb r1, [r0] - /* SDRC setting */ - ldr r0, =OMAP2420_SDRC_BASE - ldr r1, =0x00000010 - str r1, [r0, #0x10] + ldr r0, =0x48000032 /* ball D11, mode 0 */ + strb r1, [r0] - ldr r1, =0x00000100 - str r1, [r0, #0x44] + ldr r0, =0x480000A3 /* ball B13, mode 0 */ + strb r1, [r0] - /* SDRC CS0 configuration */ - ldr r1, =0x00d04011 - str r1, [r0, #0x80] + /* SDRC setting */ + ldr r0, =OMAP2420_SDRC_BASE + ldr r1, =0x00000010 + str r1, [r0, #0x10] - ldr r1, =SDRC_ACTIM_CTRLA_0_VAL - str r1, [r0, #0x9C] + ldr r1, =0x00000100 + str r1, [r0, #0x44] - ldr r1, =SDRC_ACTIM_CTRLB_0_VAL - str r1, [r0, #0xA0] + /* SDRC CS0 configuration */ + ldr r1, =0x00d04011 + str r1, [r0, #0x80] - ldr r1, =SDRC_RFR_CTRL_0_VAL - str r1, [r0, #0xA4] + ldr r1, =SDRC_ACTIM_CTRLA_0_VAL + str r1, [r0, #0x9C] - ldr r1, =0x00000041 - str r1, [r0, #0x70] + ldr r1, =SDRC_ACTIM_CTRLB_0_VAL + str r1, [r0, #0xA0] - /* Manual command sequence */ - ldr r1, =0x00000007 - str r1, [r0, #0xA8] + ldr r1, =SDRC_RFR_CTRL_0_VAL + str r1, [r0, #0xA4] - ldr r1, =0x00000000 - str r1, [r0, #0xA8] + ldr r1, =0x00000041 + str r1, [r0, #0x70] - ldr r1, =0x00000001 - str r1, [r0, #0xA8] + /* Manual command sequence */ + ldr r1, =0x00000007 + str r1, [r0, #0xA8] - ldr r1, =0x00000002 - str r1, [r0, #0xA8] - str r1, [r0, #0xA8] + ldr r1, =0x00000000 + str r1, [r0, #0xA8] - /* - * CS0 SDRC Mode register - * Burst length = 4 - DDR memory - * Serial mode - * CAS latency = 3 - */ - ldr r1, =0x00000032 - str r1, [r0, #0x84] + ldr r1, =0x00000001 + str r1, [r0, #0xA8] - /* Note: You MUST set EMR values */ - /* EMR1 & EMR2 */ - ldr r1, =0x00000000 - str r1, [r0, #0x88] - str r1, [r0, #0x8C] + ldr r1, =0x00000002 + str r1, [r0, #0xA8] + str r1, [r0, #0xA8] + + /* + * CS0 SDRC Mode register + * Burst length = 4 - DDR memory + * Serial mode + * CAS latency = 3 + */ + ldr r1, =0x00000032 + str r1, [r0, #0x84] + + /* Note: You MUST set EMR values */ + /* EMR1 & EMR2 */ + ldr r1, =0x00000000 + str r1, [r0, #0x88] + str r1, [r0, #0x8C] #ifdef OLD_SDRC_DLLA_CTRL - /* SDRC_DLLA_CTRL */ - ldr r1, =0x00007306 - str r1, [r0, #0x60] + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00007306 + str r1, [r0, #0x60] - ldr r1, =0x00007303 - str r1, [r0, #0x60] + ldr r1, =0x00007303 + str r1, [r0, #0x60] #else - /* SDRC_DLLA_CTRL */ - ldr r1, =0x00000506 - str r1, [r0, #0x60] + /* SDRC_DLLA_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x60] - ldr r1, =0x00000503 - str r1, [r0, #0x60] + ldr r1, =0x00000503 + str r1, [r0, #0x60] #endif #ifdef __BROKEN_FEATURE__ - /* SDRC_DLLB_CTRL */ - ldr r1, =0x00000506 - str r1, [r0, #0x68] + /* SDRC_DLLB_CTRL */ + ldr r1, =0x00000506 + str r1, [r0, #0x68] - ldr r1, =0x00000503 - str r1, [r0, #0x68] + ldr r1, =0x00000503 + str r1, [r0, #0x68] #endif - /* little delay after init */ - mov r2, #0x1800 + /* little delay after init */ + mov r2, #0x1800 1: - subs r2, r2, #0x1 - bne 1b + subs r2, r2, #0x1 + bne 1b /* Setup base address */ ldr r0, =0x00000000 /* NOR address */ @@ -178,21 +178,21 @@ copy_loop: #endif prcm_setup: - ldr r0, =OMAP2420_CM_BASE - ldr r1, [r0, #0x544] /* CLKSEL2_PLL */ - bic r1, r1, #0x03 - orr r1, r1, #0x02 - str r1, [r0, #0x544] - - ldr r1, [r0, #0x500] - bic r1, r1, #0x03 - orr r1, r1, #0x01 - str r1, [r0, #0x500] - - ldr r1, [r0, #0x140] - bic r1, r1, #0x1f - orr r1, r1, #0x02 - str r1, [r0, #0x140] + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x544] /* CLKSEL2_PLL */ + bic r1, r1, #0x03 + orr r1, r1, #0x02 + str r1, [r0, #0x544] + + ldr r1, [r0, #0x500] + bic r1, r1, #0x03 + orr r1, r1, #0x01 + str r1, [r0, #0x500] + + ldr r1, [r0, #0x140] + bic r1, r1, #0x1f + orr r1, r1, #0x02 + str r1, [r0, #0x140] #ifdef PRCM_CONFIG_I ldr r1, =0x000003C3 @@ -204,58 +204,58 @@ prcm_setup: ldr r1, =0x00000002 str r1, [r0, #0x340] - ldr r1, =CM_CLKSEL1_CORE + ldr r1, =CM_CLKSEL1_CORE #ifdef PRCM_CONFIG_I - ldr r2, =0x08300C44 + ldr r2, =0x08300C44 #else - ldr r2, =0x04600C26 + ldr r2, =0x04600C26 #endif - str r2, [r1] + str r2, [r1] - ldr r0, =OMAP2420_CM_BASE - ldr r1, [r0, #0x084] - and r1, r1, #0x01 - cmp r1, #0x01 - bne clkvalid + ldr r0, =OMAP2420_CM_BASE + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x01 + bne clkvalid - b . + b . clkvalid: - mov r1, #0x01 - str r1, [r0, #0x080] + mov r1, #0x01 + str r1, [r0, #0x080] waitvalid: - ldr r1, [r0, #0x084] - and r1, r1, #0x01 - cmp r1, #0x00 - bne waitvalid + ldr r1, [r0, #0x084] + and r1, r1, #0x01 + cmp r1, #0x00 + bne waitvalid - ldr r0, =CM_CLKSEL1_PLL + ldr r0, =CM_CLKSEL1_PLL #ifdef PRCM_CONFIG_I - ldr r1, =0x01837100 + ldr r1, =0x01837100 #else - ldr r1, =0x01832100 + ldr r1, =0x01832100 #endif - str r1, [r0] + str r1, [r0] - ldr r0, =PRCM_CLKCFG_CTRL - mov r1, #0x01 - str r1, [r0] - mov r6, #0x50 + ldr r0, =PRCM_CLKCFG_CTRL + mov r1, #0x01 + str r1, [r0] + mov r6, #0x50 loop1: - subs r6, r6, #0x01 - cmp r6, #0x01 - bne loop1 + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop1 - ldr r0, =CM_CLKEN_PLL + ldr r0, =CM_CLKEN_PLL mov r1, #0x0f - str r1, [r0] + str r1, [r0] - mov r6, #0x100 + mov r6, #0x100 loop2: - subs r6, r6, #0x01 - cmp r6, #0x01 - bne loop2 + subs r6, r6, #0x01 + cmp r6, #0x01 + bne loop2 ldr r0, =0x48008200 ldr r1, =0xbfffffff diff --git a/board/freescale/common/fsl_diu_fb.c b/board/freescale/common/fsl_diu_fb.c index c1dc48c6229..5a8576ea2b0 100644 --- a/board/freescale/common/fsl_diu_fb.c +++ b/board/freescale/common/fsl_diu_fb.c @@ -23,7 +23,6 @@ * MA 02111-1307 USA */ - #include #include #include @@ -32,14 +31,12 @@ #include "fsl_diu_fb.h" - #ifdef DEBUG #define DPRINTF(fmt, args...) printf("%s: " fmt,__FUNCTION__,## args) #else #define DPRINTF(fmt, args...) #endif - struct fb_videomode { const char *name; /* optional */ unsigned int refresh; /* optional */ @@ -182,8 +179,6 @@ struct diu_addr { #define MAX_CURS 32 - - static struct fb_info fsl_fb_info; static struct diu_addr gamma, cursor; static struct diu_ad fsl_diu_fb_ad __attribute__ ((aligned(32))); @@ -206,7 +201,6 @@ static int fsl_diu_disable_panel(struct fb_info *info); static int allocate_buf(struct diu_addr *buf, u32 size, u32 bytes_align); static u32 get_busfreq(void); - int fsl_diu_init(int xres, unsigned int pixel_format, int gamma_fix, diff --git a/include/configs/apollon.h b/include/configs/apollon.h index 7727bc3e291..f10120617c7 100755 --- a/include/configs/apollon.h +++ b/include/configs/apollon.h @@ -39,14 +39,14 @@ /* Clock config to target*/ #define PRCM_CONFIG_I 1 -//#define PRCM_CONFIG_II 1 +/* #define PRCM_CONFIG_II 1 */ /* Boot method */ /* uncomment if you use NOR boot */ -//#define CFG_NOR_BOOT 1 +/* #define CFG_NOR_BOOT 1 */ /* uncomment if you use NOR on CS3 */ -//#define CFG_USE_NOR 1 +/* #define CFG_USE_NOR 1 */ #ifdef CFG_NOR_BOOT #undef CFG_USE_NOR @@ -111,13 +111,13 @@ #define CFG_I2C_SLAVE 1 #define CONFIG_DRIVER_OMAP24XX_I2C -/* allow to overwrite serial and ethaddr */ +/* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 115200 #define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include #define CONFIG_CMD_DHCP @@ -180,8 +180,8 @@ #define CFG_LOAD_ADDR (OMAP2420_SDRC_CS0) /* default load address */ -/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) - * or by 32KHz clk, or from external sig. This rate is divided by a local +/* The 2420 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) + * or by 32KHz clk, or from external sig. This rate is divided by a local * divisor. */ #define V_PVT 7 /* use with 12MHz/128 */ @@ -193,7 +193,7 @@ /*----------------------------------------------------------------------- * Stack sizes * - * The stack sizes are set up in start.S using the settings below + * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE SZ_128K /* regular stack */ #ifdef CONFIG_USE_IRQ @@ -223,7 +223,7 @@ */ # define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ # define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ -//#define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ +/* #define CFG_FLASH_USE_BUFFER_WRITE 1 */ /* Use buffered writes (~10x faster) */ # define CFG_FLASH_PROTECTION 1 /* Use h/w sector protection*/ #else /* !CFG_USE_NOR */ -- cgit v1.3.1 From a2df4da31b1a1e41e3e9e1358cfc52b806046ce1 Mon Sep 17 00:00:00 2001 From: Jean-Christophe PLAGNIOL-VILLARD Date: Sun, 9 Dec 2007 11:01:10 +0100 Subject: Add missing file in gitignore and comments based on Linux source tree's .gitignore files Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD --- .gitignore | 32 ++++++++++++++++++++++++++++++-- include/.gitignore | 1 + 2 files changed, 31 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/.gitignore b/.gitignore index 67fed082c83..cda275ec73b 100644 --- a/.gitignore +++ b/.gitignore @@ -1,13 +1,41 @@ +# +# NOTE! Don't add files that are generated in specific +# subdirectories here. Add them in the ".gitignore" file +# in that subdirectory instead. +# +# Normal rules +# + +*.rej *.orig *.a *.o -*.depend -System.map + +# +# Top-level generic files +# + +/System.map /u-boot /u-boot.map /u-boot.bin /u-boot.srec + +# +# Generated files +# + +*.depend /LOG /errlog /reloc_off +# stgit generated dirs +patches-* + +# quilt's files +patches +series + +# cscope files +cscope.* diff --git a/include/.gitignore b/include/.gitignore index d8fda80d5ea..ab7d4c76f4b 100644 --- a/include/.gitignore +++ b/include/.gitignore @@ -1,3 +1,4 @@ +/autoconf.mk* /asm /asm-ppc/arch /bmp_logo.h -- cgit v1.3.1 From d16471ee05ce7ac5392bc0e9fe3ff4b58a768f33 Mon Sep 17 00:00:00 2001 From: Harald Welte Date: Wed, 19 Dec 2007 14:14:47 +0100 Subject: add 'terminal program' functionality This patch adds a 'cu' like serial terminal command to u-boot using which you can access other serial ports from the system console. OpenMoko uses this in their Neo1973 phones to get access to the GSM Modem and GPS chip from the bootloader. Signed-off-by: Harald Welte --- common/Makefile | 1 + common/cmd_terminal.c | 102 +++++++++++++++++++++++++++++++++++++++++++++++ include/config_cmd_all.h | 1 + 3 files changed, 104 insertions(+) create mode 100644 common/cmd_terminal.c (limited to 'include') diff --git a/common/Makefile b/common/Makefile index 7be89a41c6e..fbfa536a30c 100644 --- a/common/Makefile +++ b/common/Makefile @@ -86,6 +86,7 @@ COBJS-$(CONFIG_CMD_REISER) += cmd_reiser.o COBJS-y += cmd_sata.o COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o +COBJS-$(CONFIG_CMD_TERMINAL) += cmd_terminal.o COBJS-$(CONFIG_CMD_UNIVERSE) += cmd_universe.o COBJS-$(CONFIG_CMD_USB) += cmd_usb.o COBJS-y += cmd_vfd.o diff --git a/common/cmd_terminal.c b/common/cmd_terminal.c new file mode 100644 index 00000000000..88716072b30 --- /dev/null +++ b/common/cmd_terminal.c @@ -0,0 +1,102 @@ +/* + * (C) Copyright 2007 OpenMoko, Inc. + * Written by Harald Welte + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Boot support + */ +#include +#include +#include + +#if defined(CONFIG_CMD_TERMINAL) + +int do_terminal(cmd_tbl_t * cmd, int flag, int argc, char *argv[]) +{ + int i, l; + int last_tilde = 0; + device_t *dev = NULL; + + if (argc < 1) + return -1; + + /* Scan for selected output/input device */ + for (i = 1; i <= ListNumItems (devlist); i++) { + device_t *tmp = ListGetPtrToItem (devlist, i); + if (!strcmp(tmp->name, argv[1])) { + dev = tmp; + break; + } + } + if (!dev) + return -1; + + serial_reinit_all(); + printf("Entering terminal mode for port %s\n", dev->name); + puts("Use '~.' to leave the terminal and get back to u-boot\n"); + + while (1) { + int c; + + /* read from console and display on serial port */ + if (stdio_devices[0]->tstc()) { + c = stdio_devices[0]->getc(); + if (last_tilde == 1) { + if (c == '.') { + putc(c); + putc('\n'); + break; + } else { + last_tilde = 0; + /* write the delayed tilde */ + dev->putc('~'); + /* fall-through to print current + * character */ + } + } + if (c == '~') { + last_tilde = 1; + puts("[u-boot]"); + putc(c); + } + dev->putc(c); + } + + /* read from serial port and display on console */ + if (dev->tstc()) { + c = dev->getc(); + putc(c); + } + } + return 0; +} + + +/***************************************************/ + +U_BOOT_CMD( + terminal, 3, 1, do_terminal, + "terminal - start terminal emulator\n", + "" +); + +#endif /* CONFIG_CMD_TERMINAL */ diff --git a/include/config_cmd_all.h b/include/config_cmd_all.h index d7ef65d5dde..f3965efe953 100644 --- a/include/config_cmd_all.h +++ b/include/config_cmd_all.h @@ -73,6 +73,7 @@ #define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ #define CONFIG_CMD_SNTP /* SNTP support */ #define CONFIG_CMD_SPI /* SPI utility */ +#define CONFIG_CMD_TERMINAL /* built-in Serial Terminal */ #define CONFIG_CMD_UNIVERSE /* Tundra Universe Support */ #define CONFIG_CMD_USB /* USB Support */ #define CONFIG_CMD_VFD /* VFD support (TRAB) */ -- cgit v1.3.1 From 0133502e39ff89b67c26cb4015e0e7e8d9571184 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Thu, 27 Dec 2007 17:12:34 +0100 Subject: Improve configuration of FPGA subsystem This patch removes the FPGA subsystem configuration through the CONFIG_FPGA bitmask configuration option. See README for the new options: CONFIG_FPGA, CONFIG_FPGA_, CONFIG_FPGA_ Signed-off-by: Matthias Fuchs --- README | 19 ++++++++++++++----- board/gen860t/fpga.c | 2 +- board/gen860t/gen860t.c | 2 +- common/ACEX1K.c | 4 ++-- common/altera.c | 18 +++++++++--------- common/cmd_fpga.c | 2 +- common/cyclon2.c | 4 ++-- common/fpga.c | 30 +++++++++++------------------- common/spartan2.c | 2 +- common/spartan3.c | 2 +- common/virtex2.c | 2 +- common/xilinx.c | 28 ++++++++++++++-------------- include/configs/GEN860T.h | 4 +++- include/configs/M54455EVB.h | 4 +++- include/configs/alpr.h | 4 +++- include/xilinx.h | 4 ++-- 16 files changed, 69 insertions(+), 62 deletions(-) (limited to 'include') diff --git a/README b/README index 26f93c21a76..9a8b3b903d1 100644 --- a/README +++ b/README @@ -1377,14 +1377,23 @@ The following options need to be configured: SPI configuration items (port pins to use, etc). For an example, see include/configs/sacsng.h. -- FPGA Support: CONFIG_FPGA_COUNT +- FPGA Support: CONFIG_FPGA - Specify the number of FPGA devices to support. + Enables FPGA subsystem. + + CONFIG_FPGA_ + + Enables support for specific chip vendors. + (ALTERA, XILINX) - CONFIG_FPGA + CONFIG_FPGA_ - Used to specify the types of FPGA devices. For example, - #define CONFIG_FPGA CFG_XILINX_VIRTEX2 + Enables support for FPGA family. + (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX) + + CONFIG_FPGA_COUNT + + Specify the number of FPGA devices to support. CFG_FPGA_PROG_FEEDBACK diff --git a/board/gen860t/fpga.c b/board/gen860t/fpga.c index 2ba7e0e4207..3816e52eed7 100644 --- a/board/gen860t/fpga.c +++ b/board/gen860t/fpga.c @@ -34,7 +34,7 @@ DECLARE_GLOBAL_DATA_PTR; -#if (CONFIG_FPGA) +#if defined(CONFIG_FPGA) #if 0 #define GEN860T_FPGA_DEBUG diff --git a/board/gen860t/gen860t.c b/board/gen860t/gen860t.c index d448f9fa33d..73cc16d4792 100644 --- a/board/gen860t/gen860t.c +++ b/board/gen860t/gen860t.c @@ -254,7 +254,7 @@ int misc_init_r (void) mii_init (); #endif -#if (CONFIG_FPGA) +#if defined(CONFIG_FPGA) gen860t_init_fpga (); #endif return 0; diff --git a/common/ACEX1K.c b/common/ACEX1K.c index 2a421e2da9c..76dc1664385 100644 --- a/common/ACEX1K.c +++ b/common/ACEX1K.c @@ -28,7 +28,7 @@ #include /* core U-Boot definitions */ #include /* ACEX device family */ -#if (CONFIG_FPGA & (CFG_ALTERA | CFG_ACEX1K)) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_ALTERA) && defined(CONFIG_FPGA_ACEX1K) /* Define FPGA_DEBUG to get debug printf's */ #ifdef FPGA_DEBUG @@ -363,4 +363,4 @@ static int ACEX1K_ps_reloc (Altera_desc * desc, ulong reloc_offset) } -#endif /* (CONFIG_FPGA & (CFG_ALTERA | CFG_ACEX1K)) */ +#endif /* CONFIG_FPGA && CONFIG_FPGA_ALTERA && CONFIG_FPGA_ACEX1K */ diff --git a/common/altera.c b/common/altera.c index 06e8a950158..0df7bae013e 100644 --- a/common/altera.c +++ b/common/altera.c @@ -40,7 +40,7 @@ #define PRINTF(fmt,args...) #endif -#if (CONFIG_FPGA & CFG_FPGA_ALTERA) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_ALTERA) /* Local Static Functions */ static int altera_validate (Altera_desc * desc, char *fn); @@ -56,11 +56,11 @@ int altera_load( Altera_desc *desc, void *buf, size_t bsize ) switch (desc->family) { case Altera_ACEX1K: case Altera_CYC2: -#if (CONFIG_FPGA & CFG_ACEX1K) +#if defined(CONFIG_FPGA_ACEX1K) PRINTF ("%s: Launching the ACEX1K Loader...\n", __FUNCTION__); ret_val = ACEX1K_load (desc, buf, bsize); -#elif (CONFIG_FPGA & CFG_CYCLON2) +#elif defined CONFIG_FPGA_CYCLON2 PRINTF ("%s: Launching the CYCLON II Loader...\n", __FUNCTION__); ret_val = CYC2_load (desc, buf, bsize); @@ -88,7 +88,7 @@ int altera_dump( Altera_desc *desc, void *buf, size_t bsize ) } else { switch (desc->family) { case Altera_ACEX1K: -#if (CONFIG_FPGA & CFG_ACEX) +#if defined(CONFIG_FPGA_ACEX) PRINTF ("%s: Launching the ACEX1K Reader...\n", __FUNCTION__); ret_val = ACEX1K_dump (desc, buf, bsize); @@ -156,9 +156,9 @@ int altera_info( Altera_desc *desc ) switch (desc->family) { case Altera_ACEX1K: case Altera_CYC2: -#if (CONFIG_FPGA & CFG_ACEX1K) +#if defined(CONFIG_FPGA_ACEX1K) ACEX1K_info (desc); -#elif (CONFIG_FPGA & CFG_CYCLON2) +#elif defined(CONFIG_FPGA_CYCLON2) CYC2_info (desc); #else /* just in case */ @@ -192,7 +192,7 @@ int altera_reloc( Altera_desc *desc, ulong reloc_offset) } else { switch (desc->family) { case Altera_ACEX1K: -#if (CONFIG_FPGA & CFG_ACEX1K) +#if defined(CONFIG_FPGA_ACEX1K) ret_val = ACEX1K_reloc (desc, reloc_offset); #else printf ("%s: No support for ACEX devices.\n", @@ -200,7 +200,7 @@ int altera_reloc( Altera_desc *desc, ulong reloc_offset) #endif break; case Altera_CYC2: -#if (CONFIG_FPGA & CFG_CYCLON2) +#if defined(CONFIG_FPGA_CYCLON2) ret_val = CYC2_reloc (desc, reloc_offset); #else printf ("%s: No support for CYCLON II devices.\n", @@ -249,4 +249,4 @@ static int altera_validate (Altera_desc * desc, char *fn) /* ------------------------------------------------------------------------- */ -#endif /* CONFIG_FPGA & CFG_FPGA_ALTERA */ +#endif /* CONFIG_FPGA & CONFIG_FPGA_ALTERA */ diff --git a/common/cmd_fpga.c b/common/cmd_fpga.c index 377a692f7dc..fb24395b58a 100644 --- a/common/cmd_fpga.c +++ b/common/cmd_fpga.c @@ -58,7 +58,7 @@ static int fpga_get_op (char *opstr); /* Convert bitstream data and load into the fpga */ int fpga_loadbitstream(unsigned long dev, char* fpgadata, size_t size) { -#if (CONFIG_FPGA & CFG_FPGA_XILINX) +#if defined(CONFIG_FPGA_XILINX) unsigned int length; unsigned char* swapdata; unsigned int swapsize; diff --git a/common/cyclon2.c b/common/cyclon2.c index dce13b50d00..06f5e8aeaec 100644 --- a/common/cyclon2.c +++ b/common/cyclon2.c @@ -27,7 +27,7 @@ #include #include /* ACEX device family */ -#if (CONFIG_FPGA & (CFG_ALTERA | CFG_CYCLON2)) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_ALTERA) && defined(CONFIG_FPGA_CYCLON2) /* Define FPGA_DEBUG to get debug printf's */ #ifdef FPGA_DEBUG @@ -302,4 +302,4 @@ static int CYC2_ps_reloc (Altera_desc * desc, ulong reloc_offset) return ret_val; } -#endif /* (CONFIG_FPGA & (CFG_ALTERA | CFG_CYCLON2)) */ +#endif /* CONFIG_FPGA && CONFIG_FPGA_ALTERA && CONFIG_FPGA_CYCLON2 */ diff --git a/common/fpga.c b/common/fpga.c index 2eff239c478..d8b6ae354ab 100644 --- a/common/fpga.c +++ b/common/fpga.c @@ -67,14 +67,11 @@ static int fpga_dev_info( int devnum ); static void fpga_no_sup( char *fn, char *msg ) { if ( fn && msg ) { - printf( "%s: No support for %s. CONFIG_FPGA defined as 0x%x.\n", - fn, msg, CONFIG_FPGA ); + printf( "%s: No support for %s.\n", fn, msg); } else if ( msg ) { - printf( "No support for %s. CONFIG_FPGA defined as 0x%x.\n", - msg, CONFIG_FPGA ); + printf( "No support for %s.\n", msg); } else { - printf( "No FPGA suport! CONFIG_FPGA defined as 0x%x.\n", - CONFIG_FPGA ); + printf( "No FPGA suport!\n"); } } @@ -112,11 +109,6 @@ static __attribute__((__const__)) fpga_desc * __attribute__((__const__)) fpga_va printf( "%s: Null buffer.\n", fn ); return (fpga_desc * const)NULL; } - if ( !bsize ) { - printf( "%s: Null buffer size.\n", fn ); - return (fpga_desc * const)NULL; - } - return desc; } @@ -135,7 +127,7 @@ static int fpga_dev_info( int devnum ) switch ( desc->devtype ) { case fpga_xilinx: -#if CONFIG_FPGA & CFG_FPGA_XILINX +#if defined(CONFIG_FPGA_XILINX) printf( "Xilinx Device\nDescriptor @ 0x%p\n", desc ); ret_val = xilinx_info( desc->devdesc ); #else @@ -143,7 +135,7 @@ static int fpga_dev_info( int devnum ) #endif break; case fpga_altera: -#if CONFIG_FPGA & CFG_FPGA_ALTERA +#if defined(CONFIG_FPGA_ALTERA) printf( "Altera Device\nDescriptor @ 0x%p\n", desc ); ret_val = altera_info( desc->devdesc ); #else @@ -175,14 +167,14 @@ int fpga_reloc( fpga_type devtype, void *desc, ulong reloc_off ) switch ( devtype ) { case fpga_xilinx: -#if CONFIG_FPGA & CFG_FPGA_XILINX +#if defined(CONFIG_FPGA_XILINX) ret_val = xilinx_reloc( desc, reloc_off ); #else fpga_no_sup( (char *)__FUNCTION__, "Xilinx devices" ); #endif break; case fpga_altera: -#if CONFIG_FPGA & CFG_FPGA_ALTERA +#if defined(CONFIG_FPGA_ALTERA) ret_val = altera_reloc( desc, reloc_off ); #else fpga_no_sup( (char *)__FUNCTION__, "Altera devices" ); @@ -268,14 +260,14 @@ int fpga_load( int devnum, void *buf, size_t bsize ) if ( desc ) { switch ( desc->devtype ) { case fpga_xilinx: -#if CONFIG_FPGA & CFG_FPGA_XILINX +#if defined(CONFIG_FPGA_XILINX) ret_val = xilinx_load( desc->devdesc, buf, bsize ); #else fpga_no_sup( (char *)__FUNCTION__, "Xilinx devices" ); #endif break; case fpga_altera: -#if CONFIG_FPGA & CFG_FPGA_ALTERA +#if defined(CONFIG_FPGA_ALTERA) ret_val = altera_load( desc->devdesc, buf, bsize ); #else fpga_no_sup( (char *)__FUNCTION__, "Altera devices" ); @@ -301,14 +293,14 @@ int fpga_dump( int devnum, void *buf, size_t bsize ) if ( desc ) { switch ( desc->devtype ) { case fpga_xilinx: -#if CONFIG_FPGA & CFG_FPGA_XILINX +#if defined(CONFIG_FPGA_XILINX) ret_val = xilinx_dump( desc->devdesc, buf, bsize ); #else fpga_no_sup( (char *)__FUNCTION__, "Xilinx devices" ); #endif break; case fpga_altera: -#if CONFIG_FPGA & CFG_FPGA_ALTERA +#if defined(CONFIG_FPGA_ALTERA) ret_val = altera_dump( desc->devdesc, buf, bsize ); #else fpga_no_sup( (char *)__FUNCTION__, "Altera devices" ); diff --git a/common/spartan2.c b/common/spartan2.c index 06550b9858c..457009f8584 100644 --- a/common/spartan2.c +++ b/common/spartan2.c @@ -25,7 +25,7 @@ #include /* core U-Boot definitions */ #include /* Spartan-II device family */ -#if (CONFIG_FPGA & (CFG_XILINX | CFG_SPARTAN2)) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_SPARTAN2) /* Define FPGA_DEBUG to get debug printf's */ #ifdef FPGA_DEBUG diff --git a/common/spartan3.c b/common/spartan3.c index f7c4f8cf2b2..17379eb8b1e 100644 --- a/common/spartan3.c +++ b/common/spartan3.c @@ -30,7 +30,7 @@ #include /* core U-Boot definitions */ #include /* Spartan-II device family */ -#if (CONFIG_FPGA & (CFG_XILINX | CFG_SPARTAN3)) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_SPARTAN3) /* Define FPGA_DEBUG to get debug printf's */ #ifdef FPGA_DEBUG diff --git a/common/virtex2.c b/common/virtex2.c index b5dc366aad3..1283ff610d8 100644 --- a/common/virtex2.c +++ b/common/virtex2.c @@ -31,7 +31,7 @@ #include #include -#if (CONFIG_FPGA & (CFG_XILINX | CFG_VIRTEX2)) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_VIRTEX2) #if 0 #define FPGA_DEBUG diff --git a/common/xilinx.c b/common/xilinx.c index e03e78cb285..c8982386824 100644 --- a/common/xilinx.c +++ b/common/xilinx.c @@ -32,7 +32,7 @@ #include #include -#if (CONFIG_FPGA & CFG_FPGA_XILINX) +#if defined(CONFIG_FPGA) && defined(CONFIG_FPGA_XILINX) #if 0 #define FPGA_DEBUG @@ -59,7 +59,7 @@ int xilinx_load (Xilinx_desc * desc, void *buf, size_t bsize) } else switch (desc->family) { case Xilinx_Spartan2: -#if (CONFIG_FPGA & CFG_SPARTAN2) +#if defined(CONFIG_FPGA_SPARTAN2) PRINTF ("%s: Launching the Spartan-II Loader...\n", __FUNCTION__); ret_val = Spartan2_load (desc, buf, bsize); @@ -69,7 +69,7 @@ int xilinx_load (Xilinx_desc * desc, void *buf, size_t bsize) #endif break; case Xilinx_Spartan3: -#if (CONFIG_FPGA & CFG_SPARTAN3) +#if defined(CONFIG_FPGA_SPARTAN3) PRINTF ("%s: Launching the Spartan-III Loader...\n", __FUNCTION__); ret_val = Spartan3_load (desc, buf, bsize); @@ -79,7 +79,7 @@ int xilinx_load (Xilinx_desc * desc, void *buf, size_t bsize) #endif break; case Xilinx_Virtex2: -#if (CONFIG_FPGA & CFG_VIRTEX2) +#if defined(CONFIG_FPGA_VIRTEX2) PRINTF ("%s: Launching the Virtex-II Loader...\n", __FUNCTION__); ret_val = Virtex2_load (desc, buf, bsize); @@ -106,7 +106,7 @@ int xilinx_dump (Xilinx_desc * desc, void *buf, size_t bsize) } else switch (desc->family) { case Xilinx_Spartan2: -#if (CONFIG_FPGA & CFG_SPARTAN2) +#if defined(CONFIG_FPGA_SPARTAN2) PRINTF ("%s: Launching the Spartan-II Reader...\n", __FUNCTION__); ret_val = Spartan2_dump (desc, buf, bsize); @@ -116,7 +116,7 @@ int xilinx_dump (Xilinx_desc * desc, void *buf, size_t bsize) #endif break; case Xilinx_Spartan3: -#if (CONFIG_FPGA & CFG_SPARTAN3) +#if defined(CONFIG_FPGA_SPARTAN3) PRINTF ("%s: Launching the Spartan-III Reader...\n", __FUNCTION__); ret_val = Spartan3_dump (desc, buf, bsize); @@ -126,7 +126,7 @@ int xilinx_dump (Xilinx_desc * desc, void *buf, size_t bsize) #endif break; case Xilinx_Virtex2: -#if (CONFIG_FPGA & CFG_VIRTEX2) +#if defined( CONFIG_FPGA_VIRTEX2) PRINTF ("%s: Launching the Virtex-II Reader...\n", __FUNCTION__); ret_val = Virtex2_dump (desc, buf, bsize); @@ -198,7 +198,7 @@ int xilinx_info (Xilinx_desc * desc) printf ("Device Function Table @ 0x%p\n", desc->iface_fns); switch (desc->family) { case Xilinx_Spartan2: -#if (CONFIG_FPGA & CFG_SPARTAN2) +#if defined(CONFIG_FPGA_SPARTAN2) Spartan2_info (desc); #else /* just in case */ @@ -207,7 +207,7 @@ int xilinx_info (Xilinx_desc * desc) #endif break; case Xilinx_Spartan3: -#if (CONFIG_FPGA & CFG_SPARTAN3) +#if defined(CONFIG_FPGA_SPARTAN3) Spartan3_info (desc); #else /* just in case */ @@ -216,7 +216,7 @@ int xilinx_info (Xilinx_desc * desc) #endif break; case Xilinx_Virtex2: -#if (CONFIG_FPGA & CFG_VIRTEX2) +#if defined(CONFIG_FPGA_VIRTEX2) Virtex2_info (desc); #else /* just in case */ @@ -249,7 +249,7 @@ int xilinx_reloc (Xilinx_desc * desc, ulong reloc_offset) } else switch (desc->family) { case Xilinx_Spartan2: -#if (CONFIG_FPGA & CFG_SPARTAN2) +#if defined(CONFIG_FPGA_SPARTAN2) ret_val = Spartan2_reloc (desc, reloc_offset); #else printf ("%s: No support for Spartan-II devices.\n", @@ -257,7 +257,7 @@ int xilinx_reloc (Xilinx_desc * desc, ulong reloc_offset) #endif break; case Xilinx_Spartan3: -#if (CONFIG_FPGA & CFG_SPARTAN3) +#if defined(CONFIG_FPGA_SPARTAN3) ret_val = Spartan3_reloc (desc, reloc_offset); #else printf ("%s: No support for Spartan-III devices.\n", @@ -265,7 +265,7 @@ int xilinx_reloc (Xilinx_desc * desc, ulong reloc_offset) #endif break; case Xilinx_Virtex2: -#if (CONFIG_FPGA & CFG_VIRTEX2) +#if defined(CONFIG_FPGA_VIRTEX2) ret_val = Virtex2_reloc (desc, reloc_offset); #else printf ("%s: No support for Virtex-II devices.\n", @@ -308,4 +308,4 @@ static int xilinx_validate (Xilinx_desc * desc, char *fn) return ret_val; } -#endif /* CONFIG_FPGA & CFG_FPGA_XILINX */ +#endif /* CONFIG_FPGA && CONFIG_FPGA_XILINX */ diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h index bfbf3a839cf..3eb3131d4d8 100644 --- a/include/configs/GEN860T.h +++ b/include/configs/GEN860T.h @@ -273,7 +273,9 @@ * Virtex2 FPGA configuration support */ #define CONFIG_FPGA_COUNT 1 -#define CONFIG_FPGA CFG_XILINX_VIRTEX2 +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_VIRTEX2 #define CFG_FPGA_PROG_FEEDBACK diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index db309584b9a..35637f92c9f 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -192,7 +192,9 @@ /* FPGA - Spartan 2 */ /* experiment -#define CONFIG_FPGA CFG_SPARTAN3 +#define CONFIG_FPGA +#define CONFIG_FPGA_XILINX +#define CONFIG_FPGA_SPARTAN3 #define CONFIG_FPGA_COUNT 1 #define CFG_FPGA_PROG_FEEDBACK #define CFG_FPGA_CHECK_CTRLC diff --git a/include/configs/alpr.h b/include/configs/alpr.h index aff9823d559..cfe08c85647 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -296,7 +296,9 @@ /*----------------------------------------------------------------------- * FPGA stuff *-----------------------------------------------------------------------*/ -#define CONFIG_FPGA CFG_ALTERA_CYCLON2 +#define CONFIG_FPGA +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_CYCLON2 #define CFG_FPGA_CHECK_CTRLC #define CFG_FPGA_PROG_FEEDBACK #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in diff --git a/include/xilinx.h b/include/xilinx.h index 3704e1d938d..95ebe3d92b6 100644 --- a/include/xilinx.h +++ b/include/xilinx.h @@ -31,11 +31,11 @@ *********************************************************************/ #define CFG_SPARTAN2 CFG_FPGA_DEV( 0x1 ) #define CFG_VIRTEX_E CFG_FPGA_DEV( 0x2 ) -#define CFG_VIRTEX2 CFG_FPGA_DEV( 0x4 ) +#define CFG_VIRTEX2 CFG_FPGA_DEV( 0x4 ) #define CFG_SPARTAN3 CFG_FPGA_DEV( 0x8 ) #define CFG_XILINX_SPARTAN2 (CFG_FPGA_XILINX | CFG_SPARTAN2) #define CFG_XILINX_VIRTEX_E (CFG_FPGA_XILINX | CFG_VIRTEX_E) -#define CFG_XILINX_VIRTEX2 (CFG_FPGA_XILINX | CFG_VIRTEX2) +#define CFG_XILINX_VIRTEX2 (CFG_FPGA_XILINX | CFG_VIRTEX2) #define CFG_XILINX_SPARTAN3 (CFG_FPGA_XILINX | CFG_SPARTAN3) /* XXX - Add new models here */ -- cgit v1.3.1 From 21d39d598c4e74d4e7761608c79dba2715d40a4c Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Thu, 27 Dec 2007 17:12:43 +0100 Subject: Add pre and post configuration callbacks for Spartan FPGAs This patch adds a post configuration callback for Spartan2/3 FPGAs. pre and post configuration callback are now optional and not called when the function pointer is set to NULL. Signed-off-by: Matthias Fuchs --- common/spartan2.c | 18 ++++++++++++++++-- common/spartan3.c | 18 ++++++++++++++++-- include/spartan2.h | 1 + include/spartan3.h | 1 + 4 files changed, 34 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/common/spartan2.c b/common/spartan2.c index 457009f8584..ef107bcbc86 100644 --- a/common/spartan2.c +++ b/common/spartan2.c @@ -561,6 +561,13 @@ static int Spartan2_ss_load (Xilinx_desc * desc, void *buf, size_t bsize) } putc ('\n'); /* terminate the dotted line */ + /* + * Run the post configuration function if there is one. + */ + if (*fn->post) { + (*fn->post) (cookie); + } + #ifdef CFG_FPGA_PROG_FEEDBACK if (ret_val == FPGA_SUCCESS) { puts ("Done.\n"); @@ -615,8 +622,10 @@ static int Spartan2_ss_reloc (Xilinx_desc * desc, ulong reloc_offset) PRINTF ("%s: Relocating descriptor at 0x%p\n", __FUNCTION__, desc); - addr = (ulong) (fn->pre) + reloc_offset; - fn_r->pre = (Xilinx_pre_fn) addr; + if (fn->pre) { + addr = (ulong) (fn->pre) + reloc_offset; + fn_r->pre = (Xilinx_pre_fn) addr; + } addr = (ulong) (fn->pgm) + reloc_offset; fn_r->pgm = (Xilinx_pgm_fn) addr; @@ -633,6 +642,11 @@ static int Spartan2_ss_reloc (Xilinx_desc * desc, ulong reloc_offset) addr = (ulong) (fn->wr) + reloc_offset; fn_r->wr = (Xilinx_wr_fn) addr; + if (fn->post) { + addr = (ulong) (fn->post) + reloc_offset; + fn_r->post = (Xilinx_post_fn) addr; + } + fn_r->relocated = TRUE; } else { diff --git a/common/spartan3.c b/common/spartan3.c index 17379eb8b1e..56a172e0be8 100644 --- a/common/spartan3.c +++ b/common/spartan3.c @@ -566,6 +566,13 @@ static int Spartan3_ss_load (Xilinx_desc * desc, void *buf, size_t bsize) } putc ('\n'); /* terminate the dotted line */ + /* + * Run the post configuration function if there is one. + */ + if (*fn->post) { + (*fn->post) (cookie); + } + #ifdef CFG_FPGA_PROG_FEEDBACK if (ret_val == FPGA_SUCCESS) { puts ("Done.\n"); @@ -620,8 +627,10 @@ static int Spartan3_ss_reloc (Xilinx_desc * desc, ulong reloc_offset) PRINTF ("%s: Relocating descriptor at 0x%p\n", __FUNCTION__, desc); - addr = (ulong) (fn->pre) + reloc_offset; - fn_r->pre = (Xilinx_pre_fn) addr; + if (fn->pre) { + addr = (ulong) (fn->pre) + reloc_offset; + fn_r->pre = (Xilinx_pre_fn) addr; + } addr = (ulong) (fn->pgm) + reloc_offset; fn_r->pgm = (Xilinx_pgm_fn) addr; @@ -638,6 +647,11 @@ static int Spartan3_ss_reloc (Xilinx_desc * desc, ulong reloc_offset) addr = (ulong) (fn->wr) + reloc_offset; fn_r->wr = (Xilinx_wr_fn) addr; + if (fn->post) { + addr = (ulong) (fn->post) + reloc_offset; + fn_r->post = (Xilinx_post_fn) addr; + } + fn_r->relocated = TRUE; } else { diff --git a/include/spartan2.h b/include/spartan2.h index d2e81e38ab5..f3cde688f78 100644 --- a/include/spartan2.h +++ b/include/spartan2.h @@ -58,6 +58,7 @@ typedef struct { Xilinx_init_fn init; Xilinx_done_fn done; Xilinx_wr_fn wr; + Xilinx_post_fn post; int relocated; } Xilinx_Spartan2_Slave_Serial_fns; diff --git a/include/spartan3.h b/include/spartan3.h index 65a3f5a4dbc..529aade6577 100644 --- a/include/spartan3.h +++ b/include/spartan3.h @@ -58,6 +58,7 @@ typedef struct { Xilinx_init_fn init; Xilinx_done_fn done; Xilinx_wr_fn wr; + Xilinx_post_fn post; int relocated; } Xilinx_Spartan3_Slave_Serial_fns; -- cgit v1.3.1 From 3bff4ffa33729a42645e328a21e8d16488872958 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Thu, 27 Dec 2007 17:12:56 +0100 Subject: Add new Xilinx Spartan FPGA types Signed-off-by: Matthias Fuchs --- include/spartan2.h | 4 ++++ include/spartan3.h | 10 +++++++++- 2 files changed, 13 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/include/spartan2.h b/include/spartan2.h index f3cde688f78..bd159e18230 100644 --- a/include/spartan2.h +++ b/include/spartan2.h @@ -70,6 +70,7 @@ typedef struct { #define XILINX_XC2S50_SIZE 559232/8 #define XILINX_XC2S100_SIZE 781248/8 #define XILINX_XC2S150_SIZE 1040128/8 +#define XILINX_XC2S200_SIZE 1335872/8 /* Spartan-IIE (1.8V) */ #define XILINX_XC2S50E_SIZE 630048/8 @@ -96,6 +97,9 @@ typedef struct { #define XILINX_XC2S150_DESC(iface, fn_table, cookie) \ { Xilinx_Spartan2, iface, XILINX_XC2S150_SIZE, fn_table, cookie } +#define XILINX_XC2S200_DESC(iface, fn_table, cookie) \ +{ Xilinx_Spartan2, iface, XILINX_XC2S200_SIZE, fn_table, cookie } + #define XILINX_XC2S50E_DESC(iface, fn_table, cookie) \ { Xilinx_Spartan2, iface, XILINX_XC2S50E_SIZE, fn_table, cookie } diff --git a/include/spartan3.h b/include/spartan3.h index 529aade6577..c203eeb580f 100644 --- a/include/spartan3.h +++ b/include/spartan3.h @@ -81,9 +81,12 @@ typedef struct { #define XILINX_XC3S1200E_SIZE 3841184/8 #define XILINX_XC3S1600E_SIZE 5969696/8 +/* Spartan-IIIE (1.2V) */ +#define XILINX_XC3S1200E_SIZE 3841184/8 + /* Descriptor Macros *********************************************************************/ -/* Spartan-II devices */ +/* Spartan-III devices */ #define XILINX_XC3S50_DESC(iface, fn_table, cookie) \ { Xilinx_Spartan3, iface, XILINX_XC3S50_SIZE, fn_table, cookie } @@ -125,4 +128,9 @@ typedef struct { #define XILINX_XC3S1600E_DESC(iface, fn_table, cookie) \ { Xilinx_Spartan3, iface, XILINX_XC3S1600E_SIZE, fn_table, cookie } + +/* Spartan-IIIE devices */ +#define XILINX_XC3S1200E_DESC(iface, fn_table, cookie) \ +{ Xilinx_Spartan3, iface, XILINX_XC3S1200E_SIZE, fn_table, cookie } + #endif /* _SPARTAN3_H_ */ -- cgit v1.3.1 From 1df170f8b2a99e1e2f940f9f0b56511e1e4c9e1f Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Fri, 4 Jan 2008 12:07:27 -0600 Subject: Convert MPC8610HPCD to use libfdt. Assumes the presence of the aliases node in the DTS to locate the pci and serial nodes for fixups. Use consistent fdtaddr and fdtfile in environment variables. Signed-off-by: Jon Loeliger --- board/freescale/mpc8610hpcd/mpc8610hpcd.c | 73 +++++++++++++++++-------------- include/configs/MPC8610HPCD.h | 31 ++++++------- 2 files changed, 54 insertions(+), 50 deletions(-) (limited to 'include') diff --git a/board/freescale/mpc8610hpcd/mpc8610hpcd.c b/board/freescale/mpc8610hpcd/mpc8610hpcd.c index 9f32890c8b1..264e95962c7 100644 --- a/board/freescale/mpc8610hpcd/mpc8610hpcd.c +++ b/board/freescale/mpc8610hpcd/mpc8610hpcd.c @@ -29,12 +29,8 @@ #include #include #include - - -#if defined(CONFIG_OF_FLAT_TREE) -#include -extern void ft_cpu_setup(void *blob, bd_t *bd); -#endif +#include +#include #include "../common/pixis.h" @@ -459,46 +455,57 @@ void pci_init_board(void) #endif /* CONFIG_PCI1 */ } -#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +#if defined(CONFIG_OF_BOARD_SETUP) void ft_board_setup(void *blob, bd_t *bd) { - u32 *p; - int len; + int node, tmp[2]; + const char *path; - ft_cpu_setup(blob, bd); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "timebase-frequency", bd->bi_busfreq / 4, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "cpu", 4, + "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_prop_u32(blob, "device_type", "soc", 4, + "bus-frequency", bd->bi_busfreq, 1); - p = ft_get_prop(blob, "/memory/reg", &len); - if (p != NULL) { - *p++ = cpu_to_be32(bd->bi_memstart); - *p = cpu_to_be32(bd->bi_memsize); - } + do_fixup_by_compat_u32(blob, "ns16550", + "clock-frequency", bd->bi_busfreq, 1); + + fdt_fixup_memory(blob, bd->bi_memstart, bd->bi_memsize); + + + node = fdt_path_offset(blob, "/aliases"); + tmp[0] = 0; + if (node >= 0) { #ifdef CONFIG_PCI1 - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pci@8000/bus-range", &len); - if (p != NULL) { - p[0] = 0; - p[1] = pci1_hose.last_busno - pci1_hose.first_busno; - debug("pci@8000 first_busno=%d last_busno=%d\n",p[0],p[1]); - } + path = fdt_getprop(blob, node, "pci0", NULL); + if (path) { + tmp[1] = pci1_hose.last_busno - pci1_hose.first_busno; + do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); + } + #endif #ifdef CONFIG_PCIE1 - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pcie@a000/bus-range", &len); - if (p != NULL) { - p[0] = 0; - p[1] = pcie1_hose.last_busno - pcie1_hose.first_busno; - debug("pcie@9000 first_busno=%d last_busno=%d\n",p[0],p[1]); + path = fdt_getprop(blob, node, "pci1", NULL); + if (path) { + tmp[1] = pcie1_hose.last_busno + - pcie1_hose.first_busno; + do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); } #endif #ifdef CONFIG_PCIE2 - p = (u32 *)ft_get_prop(blob, "/" OF_SOC "/pcie@9000/bus-range", &len); - if (p != NULL) { - p[0] = 0; - p[1] = pcie2_hose.last_busno - pcie2_hose.first_busno; - debug("pcie@9000 first_busno=%d last_busno=%d\n",p[0],p[1]); - } + path = fdt_getprop(blob, node, "pci2", NULL); + if (path) { + tmp[1] = pcie2_hose.last_busno + - pcie2_hose.first_busno; + do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); + } #endif - + } } #endif diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 55df5aa10e6..11c18361795 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -245,17 +245,14 @@ /* * Pass open firmware flat tree to kernel */ -#define CONFIG_OF_FLAT_TREE 1 -#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + /* maximum size of the flat tree (8K) */ #define OF_FLAT_TREE_MAX_SIZE 8192 -#define OF_CPU "PowerPC,8610@0" -#define OF_SOC "soc@e0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc@e0000000/serial@4500" - #define CFG_64BIT_VSPRINTF 1 #define CFG_64BIT_STRTOUL 1 @@ -618,8 +615,8 @@ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ - "dtbaddr=c00000\0" \ - "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ "bdev=sda3\0" \ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ @@ -658,8 +655,8 @@ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ - "dtbaddr=c00000\0" \ - "dtbfile=8610hpcd/mpc8610_hpcd.dtb\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ "bdev=sda3\0" \ "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\ "monitor=0-DVI\0" @@ -671,22 +668,22 @@ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr $ramdiskaddr $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ - "tftp $dtbaddr $dtbfile;" \ - "bootm $loadaddr - $dtbaddr" + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #endif /* __CONFIG_H */ -- cgit v1.3.1 From 26a41790f8eba19ad450e18ae91351daf485b3e2 Mon Sep 17 00:00:00 2001 From: Rafal Jaworowski Date: Wed, 9 Jan 2008 18:05:27 +0100 Subject: Globalize envmatch() The newly introduced API (routines related to env vars) will need to call it. Signed-off-by: Rafal Zabdyr --- common/cmd_nvedit.c | 5 +---- include/common.h | 1 + 2 files changed, 2 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/common/cmd_nvedit.c b/common/cmd_nvedit.c index 67704088104..dd263b66663 100644 --- a/common/cmd_nvedit.c +++ b/common/cmd_nvedit.c @@ -81,8 +81,6 @@ extern void env_crc_update (void); /************************************************************************ ************************************************************************/ -static int envmatch (uchar *, int); - /* * Table with supported baudrates (defined in config_xyz.h) */ @@ -576,8 +574,7 @@ int do_saveenv (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) * If the names match, return the index for the value2, else NULL. */ -static int -envmatch (uchar *s1, int i2) +int envmatch (uchar *s1, int i2) { while (*s1 == env_get_char(i2++)) diff --git a/include/common.h b/include/common.h index 493417f8776..da2f01b464d 100644 --- a/include/common.h +++ b/include/common.h @@ -227,6 +227,7 @@ extern ulong load_addr; /* Default Load Address */ /* common/cmd_nvedit.c */ int env_init (void); void env_relocate (void); +int envmatch (uchar *, int); char *getenv (char *); int getenv_r (char *name, char *buf, unsigned len); int saveenv (void); -- cgit v1.3.1 From fe8dd0b2220b7c02b0d4c9c4f9967879970477b1 Mon Sep 17 00:00:00 2001 From: Jon Loeliger Date: Wed, 9 Jan 2008 12:14:55 -0600 Subject: 86xx: Remove cache config from configs.h Just use the standard defines in asm/cache.h. Signed-off-by: Jon Loeliger --- include/configs/MPC8610HPCD.h | 7 ------- 1 file changed, 7 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 11c18361795..eb6ccb6e196 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -514,13 +514,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * -- cgit v1.3.1 From 500856eb1707ed17d9204baa61dd59948d3b2899 Mon Sep 17 00:00:00 2001 From: Rafal Jaworowski Date: Wed, 9 Jan 2008 19:39:36 +0100 Subject: API for external applications. This is an API for external (standalone) applications running on top of U-Boot, and is meant to be more extensible and robust than the existing jumptable mechanism. It is similar to UNIX syscall approach. See api/README for more details. Included is the demo application using this new framework (api_examples). Please note this is still an experimental feature, and is turned off by default. Signed-off-by: Rafal Jaworowski --- Makefile | 10 + api/Makefile | 40 +++ api/README | 55 ++++ api/api.c | 670 ++++++++++++++++++++++++++++++++++++++++++++++ api/api_net.c | 113 ++++++++ api/api_platform-arm.c | 60 +++++ api/api_platform-ppc.c | 79 ++++++ api/api_private.h | 48 ++++ api/api_storage.c | 370 +++++++++++++++++++++++++ api_examples/Makefile | 103 +++++++ api_examples/crt0.S | 50 ++++ api_examples/demo.c | 258 ++++++++++++++++++ api_examples/glue.c | 405 ++++++++++++++++++++++++++++ api_examples/glue.h | 76 ++++++ api_examples/libgenwrap.c | 90 +++++++ include/api_public.h | 102 +++++++ include/common.h | 3 + lib_ppc/board.c | 5 + 18 files changed, 2537 insertions(+) create mode 100644 api/Makefile create mode 100644 api/README create mode 100644 api/api.c create mode 100644 api/api_net.c create mode 100644 api/api_platform-arm.c create mode 100644 api/api_platform-ppc.c create mode 100644 api/api_private.h create mode 100644 api/api_storage.c create mode 100644 api_examples/Makefile create mode 100644 api_examples/crt0.S create mode 100644 api_examples/demo.c create mode 100644 api_examples/glue.c create mode 100644 api_examples/glue.h create mode 100644 api_examples/libgenwrap.c create mode 100644 include/api_public.h (limited to 'include') diff --git a/Makefile b/Makefile index 47db5b7212b..0e948751224 100644 --- a/Makefile +++ b/Makefile @@ -243,6 +243,9 @@ LIBS += $(shell if [ -d post/board/$(BOARDDIR) ]; then echo \ "post/board/$(BOARDDIR)/libpost$(BOARD).a"; fi) LIBS += common/libcommon.a LIBS += libfdt/libfdt.a +ifeq ($(CONFIG_API),y) +LIBS += api/libapi.a +endif LIBS := $(addprefix $(obj),$(LIBS)) .PHONY : $(LIBS) @@ -255,6 +258,10 @@ PLATFORM_LIBS += -L $(shell dirname `$(CC) $(CFLAGS) -print-libgcc-file-name`) - SUBDIRS = tools \ examples +ifeq ($(CONFIG_API),y) +SUBDIRS += api_examples +endif + .PHONY : $(SUBDIRS) ifeq ($(CONFIG_NAND_U_BOOT),y) @@ -2749,6 +2756,7 @@ clean: rm -f $(obj)board/bf537-stamp/u-boot.lds $(obj)board/bf561-ezkit/u-boot.lds rm -f $(obj)include/bmp_logo.h rm -f $(obj)nand_spl/u-boot-spl $(obj)nand_spl/u-boot-spl.map + rm -f $(obj)api_examples/demo clobber: clean find $(OBJTREE) -type f \( -name .depend \ @@ -2762,6 +2770,8 @@ clobber: clean rm -f $(obj)tools/inca-swap-bytes $(obj)cpu/mpc824x/bedbug_603e.c rm -f $(obj)include/asm/proc $(obj)include/asm/arch $(obj)include/asm [ ! -d $(OBJTREE)/nand_spl ] || find $(obj)nand_spl -lname "*" -print | xargs rm -f + find $(obj)api_examples -lname "*" -print | xargs rm -f + rm -f $(obj)api_examples/demo ifeq ($(OBJTREE),$(SRCTREE)) mrproper \ diff --git a/api/Makefile b/api/Makefile new file mode 100644 index 00000000000..94de3dc395a --- /dev/null +++ b/api/Makefile @@ -0,0 +1,40 @@ +# +# (C) Copyright 2007 Semihalf +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundatio; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)libapi.a + +COBJS = api.o api_net.o api_storage.o api_platform-$(ARCH).o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +all: $(LIB) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend diff --git a/api/README b/api/README new file mode 100644 index 00000000000..c8f9c457c44 --- /dev/null +++ b/api/README @@ -0,0 +1,55 @@ +U-Boot machine/arch independent API for external apps +===================================================== + +1. Main assumptions + + - there is a single entry point (syscall) to the API + + - per current design the syscall is a C-callable function in the U-Boot + text, which might evolve into a real syscall using machine exception trap + once this initial version proves functional + + - the consumer app is responsible for producing appropriate context (call + number and arguments) + + - upon entry, the syscall dispatches the call to other (existing) U-Boot + functional areas like networking or storage operations + + - consumer application will recognize the API is available by searching + a specified (assumed by convention) range of address space for the + signature + + - the U-Boot integral part of the API is meant to be thin and non-intrusive, + leaving as much processing as possible on the consumer application side, + for example it doesn't keep states, but relies on hints from the app and + so on + + - optional (CONFIG_API) + + +2. Calls + + - console related (getc, putc, tstc etc.) + - system (reset, platform info) + - time (delay, current) + - env vars (enumerate all, get, set) + - devices (enumerate all, open, close, read, write); currently two classes + of devices are recognized and supported: network and storage (ide, scsi, + usb etc.) + + +3. Structure overview + + - core API, integral part of U-Boot, mandatory + - implements the single entry point (mimics UNIX syscall) + + - glue + - entry point at the consumer side, allows to make syscall, mandatory + part + + - helper conveniency wrappers so that consumer app does not have to use + the syscall directly, but in a more friendly manner (a la libc calls), + optional part + + - consumer application + - calls directly, or leverages the provided glue mid-layer diff --git a/api/api.c b/api/api.c new file mode 100644 index 00000000000..10f83eb691c --- /dev/null +++ b/api/api.c @@ -0,0 +1,670 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#if defined(CONFIG_API) + +#include +#include +#include +#include +#include + +#include "api_private.h" + +#define DEBUG +#undef DEBUG + +/* U-Boot routines needed */ +extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); +extern uchar (*env_get_char)(int); +extern uchar *env_get_addr(int); + +/***************************************************************************** + * + * This is the API core. + * + * API_ functions are part of U-Boot code and constitute the lowest level + * calls: + * + * - they know what values they need as arguments + * - their direct return value pertains to the API_ "shell" itself (0 on + * success, some error code otherwise) + * - if the call returns a value it is buried within arguments + * + ****************************************************************************/ + +#ifdef DEBUG +#define debugf(fmt, args...) do { printf("%s(): ", __func__); printf(fmt, ##args); } while (0) +#else +#define debugf(fmt, args...) +#endif + +typedef int (*cfp_t)(va_list argp); + +static int calls_no; + +/* + * pseudo signature: + * + * int API_getc(int *c) + */ +static int API_getc(va_list ap) +{ + int *c; + + if ((c = (int *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + *c = getc(); + return 0; +} + +/* + * pseudo signature: + * + * int API_tstc(int *c) + */ +static int API_tstc(va_list ap) +{ + int *t; + + if ((t = (int *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + *t = tstc(); + return 0; +} + +/* + * pseudo signature: + * + * int API_putc(char *ch) + */ +static int API_putc(va_list ap) +{ + char *c; + + if ((c = (char *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + putc(*c); + return 0; +} + +/* + * pseudo signature: + * + * int API_puts(char **s) + */ +static int API_puts(va_list ap) +{ + char *s; + + if ((s = (char *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + puts(s); + return 0; +} + +/* + * pseudo signature: + * + * int API_reset(void) + */ +static int API_reset(va_list ap) +{ + do_reset(NULL, 0, 0, NULL); + + /* NOT REACHED */ + return 0; +} + +/* + * pseudo signature: + * + * int API_get_sys_info(struct sys_info *si) + * + * fill out the sys_info struct containing selected parameters about the + * machine + */ +static int API_get_sys_info(va_list ap) +{ + struct sys_info *si; + + si = (struct sys_info *)va_arg(ap, u_int32_t); + if (si == NULL) + return API_ENOMEM; + + return (platform_sys_info(si)) ? 0 : API_ENODEV; +} + +/* + * pseudo signature: + * + * int API_udelay(unsigned long *udelay) + */ +static int API_udelay(va_list ap) +{ + unsigned long *d; + + if ((d = (unsigned long *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + udelay(*d); + return 0; +} + +/* + * pseudo signature: + * + * int API_get_timer(unsigned long *current, unsigned long *base) + */ +static int API_get_timer(va_list ap) +{ + unsigned long *base, *cur; + + cur = (unsigned long *)va_arg(ap, u_int32_t); + if (cur == NULL) + return API_EINVAL; + + base = (unsigned long *)va_arg(ap, u_int32_t); + if (base == NULL) + return API_EINVAL; + + *cur = get_timer(*base); + return 0; +} + + +/***************************************************************************** + * + * pseudo signature: + * + * int API_dev_enum(struct device_info *) + * + * + * cookies uniqely identify the previously enumerated device instance and + * provide a hint for what to inspect in current enum iteration: + * + * - net: ð_device struct address from list pointed to by eth_devices + * + * - storage: block_dev_desc_t struct address from &ide_dev_desc[n], + * &scsi_dev_desc[n] and similar tables + * + ****************************************************************************/ + +static int API_dev_enum(va_list ap) +{ + struct device_info *di; + + /* arg is ptr to the device_info struct we are going to fill out */ + di = (struct device_info *)va_arg(ap, u_int32_t); + if (di == NULL) + return API_EINVAL; + + if (di->cookie == NULL) { + /* start over - clean up enumeration */ + dev_enum_reset(); /* XXX shouldn't the name contain 'stor'? */ + debugf("RESTART ENUM\n"); + + /* net device enumeration first */ + if (dev_enum_net(di)) + return 0; + } + + /* + * The hidden assumption is there can only be one active network + * device and it is identified upon enumeration (re)start, so there's + * no point in trying to find network devices in other cases than the + * (re)start and hence the 'next' device can only be storage + */ + if (!dev_enum_storage(di)) + /* make sure we mark there are no more devices */ + di->cookie = NULL; + + return 0; +} + + +static int API_dev_open(va_list ap) +{ + struct device_info *di; + int err = 0; + + /* arg is ptr to the device_info struct */ + di = (struct device_info *)va_arg(ap, u_int32_t); + if (di == NULL) + return API_EINVAL; + + /* Allow only one consumer of the device at a time */ + if (di->state == DEV_STA_OPEN) + return API_EBUSY; + + if (di->cookie == NULL) + return API_ENODEV; + + if (di->type & DEV_TYP_STOR) + err = dev_open_stor(di->cookie); + + else if (di->type & DEV_TYP_NET) + err = dev_open_net(di->cookie); + else + err = API_ENODEV; + + if (!err) + di->state = DEV_STA_OPEN; + + return err; +} + + +static int API_dev_close(va_list ap) +{ + struct device_info *di; + int err = 0; + + /* arg is ptr to the device_info struct */ + di = (struct device_info *)va_arg(ap, u_int32_t); + if (di == NULL) + return API_EINVAL; + + if (di->state == DEV_STA_CLOSED) + return 0; + + if (di->cookie == NULL) + return API_ENODEV; + + if (di->type & DEV_TYP_STOR) + err = dev_close_stor(di->cookie); + + else if (di->type & DEV_TYP_NET) + err = dev_close_net(di->cookie); + else + /* + * In case of unknown device we cannot change its state, so + * only return error code + */ + err = API_ENODEV; + + if (!err) + di->state = DEV_STA_CLOSED; + + return err; +} + + +/* + * Notice: this is for sending network packets only, as U-Boot does not + * support writing to storage at the moment (12.2007) + * + * pseudo signature: + * + * int API_dev_write( + * struct device_info *di, + * void *buf, + * int *len + * ) + * + * buf: ptr to buffer from where to get the data to send + * + * len: length of packet to be sent (in bytes) + * + */ +static int API_dev_write(va_list ap) +{ + struct device_info *di; + void *buf; + int *len; + int err = 0; + + /* 1. arg is ptr to the device_info struct */ + di = (struct device_info *)va_arg(ap, u_int32_t); + if (di == NULL) + return API_EINVAL; + + /* XXX should we check if device is open? i.e. the ->state ? */ + + if (di->cookie == NULL) + return API_ENODEV; + + /* 2. arg is ptr to buffer from where to get data to write */ + buf = (void *)va_arg(ap, u_int32_t); + if (buf == NULL) + return API_EINVAL; + + /* 3. arg is length of buffer */ + len = (int *)va_arg(ap, u_int32_t); + if (len == NULL) + return API_EINVAL; + if (*len <= 0) + return API_EINVAL; + + if (di->type & DEV_TYP_STOR) + /* + * write to storage is currently not supported by U-Boot: + * no storage device implements block_write() method + */ + return API_ENODEV; + + else if (di->type & DEV_TYP_NET) + err = dev_write_net(di->cookie, buf, *len); + else + err = API_ENODEV; + + return err; +} + + +/* + * pseudo signature: + * + * int API_dev_read( + * struct device_info *di, + * void *buf, + * size_t *len, + * unsigned long *start + * size_t *act_len + * ) + * + * buf: ptr to buffer where to put the read data + * + * len: ptr to length to be read + * - network: len of packet to read (in bytes) + * - storage: # of blocks to read (can vary in size depending on define) + * + * start: ptr to start block (only used for storage devices, ignored for + * network) + * + * act_len: ptr to where to put the len actually read + */ +static int API_dev_read(va_list ap) +{ + struct device_info *di; + void *buf; + lbasize_t *len_stor, *act_len_stor; + lbastart_t *start; + int *len_net, *act_len_net; + + /* 1. arg is ptr to the device_info struct */ + di = (struct device_info *)va_arg(ap, u_int32_t); + if (di == NULL) + return API_EINVAL; + + /* XXX should we check if device is open? i.e. the ->state ? */ + + if (di->cookie == NULL) + return API_ENODEV; + + /* 2. arg is ptr to buffer from where to put the read data */ + buf = (void *)va_arg(ap, u_int32_t); + if (buf == NULL) + return API_EINVAL; + + if (di->type & DEV_TYP_STOR) { + /* 3. arg - ptr to var with # of blocks to read */ + len_stor = (lbasize_t *)va_arg(ap, u_int32_t); + if (!len_stor) + return API_EINVAL; + if (*len_stor <= 0) + return API_EINVAL; + + /* 4. arg - ptr to var with start block */ + start = (lbastart_t *)va_arg(ap, u_int32_t); + + /* 5. arg - ptr to var where to put the len actually read */ + act_len_stor = (lbasize_t *)va_arg(ap, u_int32_t); + if (!act_len_stor) + return API_EINVAL; + + *act_len_stor = dev_read_stor(di->cookie, buf, *len_stor, *start); + + } else if (di->type & DEV_TYP_NET) { + + /* 3. arg points to the var with length of packet to read */ + len_net = (int *)va_arg(ap, u_int32_t); + if (!len_net) + return API_EINVAL; + if (*len_net <= 0) + return API_EINVAL; + + /* 4. - ptr to var where to put the len actually read */ + act_len_net = (int *)va_arg(ap, u_int32_t); + if (!act_len_net) + return API_EINVAL; + + *act_len_net = dev_read_net(di->cookie, buf, *len_net); + + } else + return API_ENODEV; + + return 0; +} + + +/* + * pseudo signature: + * + * int API_env_get(const char *name, char **value) + * + * name: ptr to name of env var + */ +static int API_env_get(va_list ap) +{ + char *name, **value; + + if ((name = (char *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + if ((value = (char **)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + *value = getenv(name); + + return 0; +} + +/* + * pseudo signature: + * + * int API_env_set(const char *name, const char *value) + * + * name: ptr to name of env var + * + * value: ptr to value to be set + */ +static int API_env_set(va_list ap) +{ + char *name, *value; + + if ((name = (char *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + if ((value = (char *)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + setenv(name, value); + + return 0; +} + +/* + * pseudo signature: + * + * int API_env_enum(const char *last, char **next) + * + * last: ptr to name of env var found in last iteration + */ +static int API_env_enum(va_list ap) +{ + int i, n; + char *last, **next; + + last = (char *)va_arg(ap, u_int32_t); + + if ((next = (char **)va_arg(ap, u_int32_t)) == NULL) + return API_EINVAL; + + if (last == NULL) + /* start over */ + *next = ((char *)env_get_addr(0)); + else { + *next = last; + + for (i = 0; env_get_char(i) != '\0'; i = n + 1) { + for (n = i; env_get_char(n) != '\0'; ++n) { + if (n >= CFG_ENV_SIZE) { + /* XXX shouldn't we set *next = NULL?? */ + return 0; + } + } + + if (envmatch((uchar *)last, i) < 0) + continue; + + /* try to get next name */ + i = n + 1; + if (env_get_char(i) == '\0') { + /* no more left */ + *next = NULL; + return 0; + } + + *next = ((char *)env_get_addr(i)); + return 0; + } + } + + return 0; +} + +static cfp_t calls_table[API_MAXCALL] = { NULL, }; + +/* + * The main syscall entry point - this is not reentrant, only one call is + * serviced until finished. + * + * e.g. syscall(1, int *, u_int32_t, u_int32_t, u_int32_t, u_int32_t); + * + * call: syscall number + * + * retval: points to the return value placeholder, this is the place the + * syscall puts its return value, if NULL the caller does not + * expect a return value + * + * ... syscall arguments (variable number) + * + * returns: 0 if the call not found, 1 if serviced + */ +int syscall(int call, int *retval, ...) +{ + va_list ap; + int rv; + + if (call < 0 || call >= calls_no || calls_table[call] == NULL) { + debugf("invalid call #%d\n", call); + return 0; + } + + if (calls_table[call] == NULL) { + debugf("syscall #%d does not have a handler\n", call); + return 0; + } + + va_start(ap, retval); + rv = calls_table[call](ap); + if (retval != NULL) + *retval = rv; + + return 1; +} + +void api_init(void) +{ + struct api_signature *sig = NULL; + + /* TODO put this into linker set one day... */ + calls_table[API_RSVD] = NULL; + calls_table[API_GETC] = &API_getc; + calls_table[API_PUTC] = &API_putc; + calls_table[API_TSTC] = &API_tstc; + calls_table[API_PUTS] = &API_puts; + calls_table[API_RESET] = &API_reset; + calls_table[API_GET_SYS_INFO] = &API_get_sys_info; + calls_table[API_UDELAY] = &API_udelay; + calls_table[API_GET_TIMER] = &API_get_timer; + calls_table[API_DEV_ENUM] = &API_dev_enum; + calls_table[API_DEV_OPEN] = &API_dev_open; + calls_table[API_DEV_CLOSE] = &API_dev_close; + calls_table[API_DEV_READ] = &API_dev_read; + calls_table[API_DEV_WRITE] = &API_dev_write; + calls_table[API_ENV_GET] = &API_env_get; + calls_table[API_ENV_SET] = &API_env_set; + calls_table[API_ENV_ENUM] = &API_env_enum; + calls_no = API_MAXCALL; + + debugf("API initialized with %d calls\n", calls_no); + + dev_stor_init(); + + /* + * Produce the signature so the API consumers can find it + */ + sig = malloc(sizeof(struct api_signature)); + if (sig == NULL) { + printf("API: could not allocate memory for the signature!\n"); + return; + } + + debugf("API sig @ 0x%08x\n", sig); + memcpy(sig->magic, API_SIG_MAGIC, 8); + sig->version = API_SIG_VERSION; + sig->syscall = &syscall; + sig->checksum = 0; + sig->checksum = crc32(0, (unsigned char *)sig, + sizeof(struct api_signature)); + debugf("syscall entry: 0x%08x\n", sig->syscall); +} + +void platform_set_mr(struct sys_info *si, unsigned long start, unsigned long size, + int flags) +{ + int i; + + if (!si->mr || !size || (flags == 0)) + return; + + /* find free slot */ + for (i = 0; i < si->mr_no; i++) + if (si->mr[i].flags == 0) { + /* insert new mem region */ + si->mr[i].start = start; + si->mr[i].size = size; + si->mr[i].flags = flags; + return; + } +} + +#endif /* CONFIG_API */ diff --git a/api/api_net.c b/api/api_net.c new file mode 100644 index 00000000000..9b20a1740c7 --- /dev/null +++ b/api/api_net.c @@ -0,0 +1,113 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#if defined(CONFIG_API) + +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define DEBUG +#undef DEBUG + +#if !defined(CONFIG_NET_MULTI) +#error "API/net is currently only available for platforms with CONFIG_NET_MULTI" +#endif + +#ifdef DEBUG +#define debugf(fmt, args...) do { printf("%s(): ", __func__); printf(fmt, ##args); } while (0) +#else +#define debugf(fmt, args...) +#endif + +#define errf(fmt, args...) do { printf("ERROR @ %s(): ", __func__); printf(fmt, ##args); } while (0) + + +static int dev_valid_net(void *cookie) +{ + return ((void *)eth_get_dev() == cookie) ? 1 : 0; +} + +int dev_open_net(void *cookie) +{ + if (!dev_valid_net(cookie)) + return API_ENODEV; + + if (eth_init(gd->bd) < 0) + return API_EIO; + + return 0; +} + +int dev_close_net(void *cookie) +{ + if (!dev_valid_net(cookie)) + return API_ENODEV; + + eth_halt(); + return 0; +} + +/* + * There can only be one active eth interface at a time - use what is + * currently set to eth_current + */ +int dev_enum_net(struct device_info *di) +{ + struct eth_device *eth_current = eth_get_dev(); + + di->type = DEV_TYP_NET; + di->cookie = (void *)eth_current; + if (di->cookie == NULL) + return 0; + + memcpy(di->di_net.hwaddr, eth_current->enetaddr, 6); + + debugf("device found, returning cookie 0x%08x\n", + (u_int32_t)di->cookie); + + return 1; +} + +int dev_write_net(void *cookie, void *buf, int len) +{ + /* XXX verify that cookie points to a valid net device??? */ + + return eth_send(buf, len); +} + +int dev_read_net(void *cookie, void *buf, int len) +{ + /* XXX verify that cookie points to a valid net device??? */ + + return eth_receive(buf, len); +} + +#endif /* CONFIG_API */ diff --git a/api/api_platform-arm.c b/api/api_platform-arm.c new file mode 100644 index 00000000000..ca15ca5a985 --- /dev/null +++ b/api/api_platform-arm.c @@ -0,0 +1,60 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * + * This file contains routines that fetch data from ARM-dependent sources + * (bd_info etc.) + * + */ + +#include + +#if defined(CONFIG_API) + +#include +#include + +#include +#include + +#include "api_private.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Important notice: handling of individual fields MUST be kept in sync with + * include/asm-arm/u-boot.h and include/asm-arm/global_data.h, so any changes + * need to reflect their current state and layout of structures involved! + */ +int platform_sys_info(struct sys_info *si) +{ + int i; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) + platform_set_mr(si, gd->bd->bi_dram[i].start, + gd->bd->bi_dram[i].size, MR_ATTR_DRAM); + + return 1; +} + +#endif /* CONFIG_API */ diff --git a/api/api_platform-ppc.c b/api/api_platform-ppc.c new file mode 100644 index 00000000000..ca9f9a5cd19 --- /dev/null +++ b/api/api_platform-ppc.c @@ -0,0 +1,79 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * + * This file contains routines that fetch data from PowerPC-dependent sources + * (bd_info etc.) + * + */ + +#include + +#if defined(CONFIG_API) + +#include +#include + +#include +#include + +#include "api_private.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Important notice: handling of individual fields MUST be kept in sync with + * include/asm-ppc/u-boot.h and include/asm-ppc/global_data.h, so any changes + * need to reflect their current state and layout of structures involved! + */ +int platform_sys_info(struct sys_info *si) +{ + si->clk_bus = gd->bus_clk; + si->clk_cpu = gd->cpu_clk; + +#if defined(CONFIG_5xx) || defined(CONFIG_8xx) || defined(CONFIG_8260) || \ + defined(CONFIG_E500) || defined(CONFIG_MPC86xx) +#define bi_bar bi_immr_base +#elif defined(CONFIG_MPC5xxx) +#define bi_bar bi_mbar_base +#elif defined(CONFIG_MPC83XX) +#define bi_bar bi_immrbar +#elif defined(CONFIG_MPC8220) +#define bi_bar bi_mbar_base +#endif + +#if defined(bi_bar) + si->bar = gd->bd->bi_bar; +#undef bi_bar +#else + si->bar = NULL; +#endif + + platform_set_mr(si, gd->bd->bi_memstart, gd->bd->bi_memsize, MR_ATTR_DRAM); + platform_set_mr(si, gd->bd->bi_flashstart, gd->bd->bi_flashsize, MR_ATTR_FLASH); + platform_set_mr(si, gd->bd->bi_sramstart, gd->bd->bi_sramsize, MR_ATTR_SRAM); + + return 1; +} + +#endif /* CONFIG_API */ diff --git a/api/api_private.h b/api/api_private.h new file mode 100644 index 00000000000..94a7fc509c7 --- /dev/null +++ b/api/api_private.h @@ -0,0 +1,48 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#ifndef _API_PRIVATE_H_ +#define _API_PRIVATE_H_ + +void api_init(void); +void platform_set_mr(struct sys_info *, unsigned long, unsigned long, int); +int platform_sys_info(struct sys_info *); + +void dev_enum_reset(void); +int dev_enum_storage(struct device_info *); +int dev_enum_net(struct device_info *); + +int dev_open_stor(void *); +int dev_open_net(void *); +int dev_close_stor(void *); +int dev_close_net(void *); + +lbasize_t dev_read_stor(void *, void *, lbasize_t, lbastart_t); +int dev_read_net(void *, void *, int); +int dev_write_net(void *, void *, int); + +void dev_stor_init(void); + +#endif /* _API_PRIVATE_H_ */ diff --git a/api/api_storage.c b/api/api_storage.c new file mode 100644 index 00000000000..7cd4efb45ba --- /dev/null +++ b/api/api_storage.c @@ -0,0 +1,370 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include + +#if defined(CONFIG_API) + +#include +#include + +#define DEBUG +#undef DEBUG + +#ifdef DEBUG +#define debugf(fmt, args...) do { printf("%s(): ", __func__); printf(fmt, ##args); } while (0) +#else +#define debugf(fmt, args...) +#endif + +#define errf(fmt, args...) do { printf("ERROR @ %s(): ", __func__); printf(fmt, ##args); } while (0) + + +#define ENUM_IDE 0 +#define ENUM_USB 1 +#define ENUM_SCSI 2 +#define ENUM_MMC 3 +#define ENUM_MAX 4 + +struct stor_spec { + int max_dev; + int enum_started; + int enum_ended; + int type; /* "external" type: DT_STOR_{IDE,USB,etc} */ + char name[4]; +}; + +static struct stor_spec specs[ENUM_MAX] = { { 0, 0, 0, 0, "" }, }; + + +void dev_stor_init(void) +{ +#if (CONFIG_COMMANDS & CFG_CMD_IDE) + specs[ENUM_IDE].max_dev = CFG_IDE_MAXDEVICE; + specs[ENUM_IDE].enum_started = 0; + specs[ENUM_IDE].enum_ended = 0; + specs[ENUM_IDE].type = DEV_TYP_STOR | DT_STOR_IDE; + specs[ENUM_IDE].name = "ide"; +#endif +#if (CONFIG_COMMANDS & CFG_CMD_USB) + specs[ENUM_USB].max_dev = USB_MAX_STOR_DEV; + specs[ENUM_USB].enum_started = 0; + specs[ENUM_USB].enum_ended = 0; + specs[ENUM_USB].type = DEV_TYP_STOR | DT_STOR_USB; + specs[ENUM_USB].name = "usb"; +#endif +#if (CONFIG_COMMANDS & CFG_CMD_SCSI) + specs[ENUM_SCSI].max_dev = CFG_SCSI_MAX_DEVICE; + specs[ENUM_SCSI].enum_started = 0; + specs[ENUM_SCSI].enum_ended = 0; + specs[ENUM_SCSI].type = DEV_TYP_STOR | DT_STOR_SCSI; + specs[ENUM_SCSI].name = "scsi"; +#endif +} + +/* + * Finds next available device in the storage group + * + * type: storage group type - ENUM_IDE, ENUM_SCSI etc. + * + * first: if 1 the first device in the storage group is returned (if + * exists), if 0 the next available device is searched + * + * more: returns 0/1 depending if there are more devices in this group + * available (for future iterations) + * + * returns: 0/1 depending if device found in this iteration + */ +static int dev_stor_get(int type, int first, int *more, struct device_info *di) +{ + int found = 0; + *more = 0; + + int i; + + block_dev_desc_t *dd; + + if (first) { + di->cookie = (void *)get_dev(specs[type].name, 0); + found = 1; + + } else { + for (i = 0; i < specs[type].max_dev; i++) + if (di->cookie == (void *)get_dev(specs[type].name, i)) { + /* previous cookie found -- advance to the + * next device, if possible */ + + if (++i >= specs[type].max_dev) { + /* out of range, no more to enum */ + di->cookie = NULL; + break; + } + + di->cookie = (void *)get_dev(specs[type].name, i); + found = 1; + + /* provide hint if there are more devices in + * this group to enumerate */ + if ((i + 1) < specs[type].max_dev) + *more = 1; + + break; + } + } + + if (found) { + di->type = specs[type].type; + + if (di->cookie != NULL) { + dd = (block_dev_desc_t *)di->cookie; + if (dd->type == DEV_TYPE_UNKNOWN) { + debugf("device instance exists, but is not active.."); + found = 0; + } else { + di->di_stor.block_count = dd->lba; + di->di_stor.block_size = dd->blksz; + } + } + + } else + di->cookie = NULL; + + return found; +} + + +/* + * returns: ENUM_IDE, ENUM_USB etc. based on block_dev_desc_t + */ +static int dev_stor_type(block_dev_desc_t *dd) +{ + int i, j; + + for (i = ENUM_IDE; i < ENUM_MAX; i++) + for (j = 0; j < specs[i].max_dev; j++) + if (dd == get_dev(specs[i].name, j)) + return i; + + return ENUM_MAX; +} + + +/* + * returns: 0/1 whether cookie points to some device in this group + */ +static int dev_is_stor(int type, struct device_info *di) +{ + return (dev_stor_type(di->cookie) == type) ? 1 : 0; +} + + +static int dev_enum_stor(int type, struct device_info *di) +{ + int found = 0, more = 0; + + debugf("called, type %d\n", type); + + /* + * Formulae for enumerating storage devices: + * 1. if cookie (hint from previous enum call) is NULL we start again + * with enumeration, so return the first available device, done. + * + * 2. if cookie is not NULL, check if it identifies some device in + * this group: + * + * 2a. if cookie is a storage device from our group (IDE, USB etc.), + * return next available (if exists) in this group + * + * 2b. if it isn't device from our group, check if such devices were + * ever enumerated before: + * - if not, return the first available device from this group + * - else return 0 + */ + + if (di->cookie == NULL) { + + debugf("group%d - enum restart\n", type); + + /* + * 1. Enumeration (re-)started: take the first available + * device, if exists + */ + found = dev_stor_get(type, 1, &more, di); + specs[type].enum_started = 1; + + } else if (dev_is_stor(type, di)) { + + debugf("group%d - enum continued for the next device\n", type); + + if (specs[type].enum_ended) { + debugf("group%d - nothing more to enum!\n", type); + return 0; + } + + /* 2a. Attempt to take a next available device in the group */ + found = dev_stor_get(type, 0, &more, di); + + } else { + + if (specs[type].enum_ended) { + debugf("group %d - already enumerated, skipping\n", type); + return 0; + } + + debugf("group%d - first time enum\n", type); + + if (specs[type].enum_started == 0) { + /* + * 2b. If enumerating devices in this group did not + * happen before, it means the cookie pointed to a + * device frome some other group (another storage + * group, or network); in this case try to take the + * first available device from our group + */ + specs[type].enum_started = 1; + + /* + * Attempt to take the first device in this group: + *'first element' flag is set + */ + found = dev_stor_get(type, 1, &more, di); + + } else { + errf("group%d - out of order iteration\n", type); + found = 0; + more = 0; + } + } + + /* + * If there are no more devices in this group, consider its + * enumeration finished + */ + specs[type].enum_ended = (!more) ? 1 : 0; + + if (found) + debugf("device found, returning cookie 0x%08x\n", + (u_int32_t)di->cookie); + else + debugf("no device found\n"); + + return found; +} + +void dev_enum_reset(void) +{ + int i; + + for (i = 0; i < ENUM_MAX; i ++) { + specs[i].enum_started = 0; + specs[i].enum_ended = 0; + } +} + +int dev_enum_storage(struct device_info *di) +{ + int i; + + /* + * check: ide, usb, scsi, mmc + */ + for (i = ENUM_IDE; i < ENUM_MAX; i ++) { + if (dev_enum_stor(i, di)) + return 1; + } + + return 0; +} + +static int dev_stor_is_valid(int type, block_dev_desc_t *dd) +{ + int i; + + for (i = 0; i < specs[type].max_dev; i++) + if (dd == get_dev(specs[type].name, i)) + if (dd->type != DEV_TYPE_UNKNOWN) + return 1; + + return 0; +} + + +int dev_open_stor(void *cookie) +{ + int type = dev_stor_type(cookie); + + if (type == ENUM_MAX) + return API_ENODEV; + + if (dev_stor_is_valid(type, (block_dev_desc_t *)cookie)) + return 0; + + return API_ENODEV; +} + + +int dev_close_stor(void *cookie) +{ + /* + * Not much to do as we actually do not alter storage devices upon + * close + */ + return 0; +} + + +static int dev_stor_index(block_dev_desc_t *dd) +{ + int i, type; + + type = dev_stor_type(dd); + for (i = 0; i < specs[type].max_dev; i++) + if (dd == get_dev(specs[type].name, i)) + return i; + + return (specs[type].max_dev); +} + + +lbasize_t dev_read_stor(void *cookie, void *buf, lbasize_t len, lbastart_t start) +{ + int type; + block_dev_desc_t *dd = (block_dev_desc_t *)cookie; + + if ((type = dev_stor_type(dd)) == ENUM_MAX) + return 0; + + if (!dev_stor_is_valid(type, dd)) + return 0; + + if ((dd->block_read) == NULL) { + debugf("no block_read() for device 0x%08x\n"); + return 0; + } + + return (dd->block_read(dev_stor_index(dd), start, len, buf)); +} + +#endif /* CONFIG_API */ diff --git a/api_examples/Makefile b/api_examples/Makefile new file mode 100644 index 00000000000..5812bcd3370 --- /dev/null +++ b/api_examples/Makefile @@ -0,0 +1,103 @@ +# +# (C) Copyright 2007 Semihalf +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundatio; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +ifeq ($(ARCH),ppc) +LOAD_ADDR = 0x40000 +endif + +#ifeq ($(ARCH),arm) +#LOAD_ADDR = 0xc100000 +#endif + +include $(TOPDIR)/config.mk + +ELF += demo +BIN += demo.bin + +#CFLAGS += -v + +COBJS := $(ELF:=.o) +SOBJS := crt0.o +ifeq ($(ARCH),ppc) +SOBJS += ppcstring.o +endif + +LIB = $(obj)libglue.a +LIBCOBJS= glue.o crc32.o ctype.o string.o vsprintf.o libgenwrap.o + +LIBOBJS = $(addprefix $(obj),$(SOBJS) $(LIBCOBJS)) + +SRCS := $(COBJS:.o=.c) $(LIBCOBJS:.o=.c) $(SOBJS:.o=.S) +OBJS := $(addprefix $(obj),$(COBJS)) +ELF := $(addprefix $(obj),$(ELF)) +BIN := $(addprefix $(obj),$(BIN)) + +gcclibdir := $(shell dirname `$(CC) -print-libgcc-file-name`) + +CPPFLAGS += -I.. + +all: $(obj).depend $(OBJS) $(LIB) $(BIN) $(ELF) + +######################################################################### +$(LIB): $(obj).depend $(LIBOBJS) + $(AR) $(ARFLAGS) $@ $(LIBOBJS) + +$(ELF): +$(obj)%: $(obj)%.o $(LIB) + $(LD) $(obj)crt0.o -Ttext $(LOAD_ADDR) \ + -o $@ $< $(LIB) \ + -L$(gcclibdir) -lgcc + +$(BIN): +$(obj)%.bin: $(obj)% + $(OBJCOPY) -O binary $< $@ 2>/dev/null + +$(obj)crc32.c: + @rm -f $(obj)crc32.c + ln -s $(src)../lib_generic/crc32.c $(obj)crc32.c + +$(obj)ctype.c: + @rm -f $(obj)ctype.c + ln -s $(src)../lib_generic/ctype.c $(obj)ctype.c + +$(obj)string.c: + @rm -f $(obj)string.c + ln -s $(src)../lib_generic/string.c $(obj)string.c + +$(obj)vsprintf.c: + @rm -f $(obj)vsprintf.c + ln -s $(src)../lib_generic/vsprintf.c $(obj)vsprintf.c + +ifeq ($(ARCH),ppc) +$(obj)ppcstring.S: + @rm -f $(obj)ppcstring.S + ln -s $(src)../lib_ppc/ppcstring.S $(obj)ppcstring.S +endif + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/api_examples/crt0.S b/api_examples/crt0.S new file mode 100644 index 00000000000..8d4f7064eb9 --- /dev/null +++ b/api_examples/crt0.S @@ -0,0 +1,50 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#if defined(CONFIG_PPC) + + .text + + .globl _start +_start: + b main + + + .globl syscall +syscall: + lis %r11, syscall_ptr@ha + addi %r11, %r11, syscall_ptr@l + lwz %r11, 0(%r11) + mtctr %r11 + bctr + + + .globl syscall_ptr +syscall_ptr: + .align 4 + .long 0 +#else +#error No support for this arch! +#endif diff --git a/api_examples/demo.c b/api_examples/demo.c new file mode 100644 index 00000000000..a4aeef183b5 --- /dev/null +++ b/api_examples/demo.c @@ -0,0 +1,258 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include + +#include "glue.h" + +#define errf(fmt, args...) do { printf("ERROR @ %s(): ", __func__); printf(fmt, ##args); } while (0) + +void test_dump_si(struct sys_info *); +void test_dump_di(int); +void test_dump_sig(struct api_signature *); + +char buf[2048]; + +#define WAIT_SECS 5 + +int main(int argc, char *argv[]) +{ + int rv = 0; + int h, i, j; + int devs_no; + struct api_signature *sig = NULL; + ulong start, now; + struct device_info *di; + + if (!api_search_sig(&sig)) + return -1; + + syscall_ptr = sig->syscall; + if (syscall_ptr == NULL) + return -2; + + if (sig->version > API_SIG_VERSION) + return -3; + + printf("API signature found @%x\n", sig); + test_dump_sig(sig); + + printf("\n*** Consumer API test ***\n"); + printf("syscall ptr 0x%08x@%08x\n", syscall_ptr, &syscall_ptr); + + /* console activities */ + ub_putc('B'); + + printf("*** Press any key to continue ***\n"); + printf("got char 0x%x\n", ub_getc()); + + /* system info */ + test_dump_si(ub_get_sys_info()); + + /* timing */ + printf("\n*** Timing - wait a couple of secs ***\n"); + start = ub_get_timer(0); + printf("\ntime: start %lu\n\n", start); + for (i = 0; i < WAIT_SECS; i++) + for (j = 0; j < 1000; j++) + ub_udelay(1000); /* wait 1 ms */ + + /* this is the number of milliseconds that passed from ub_get_timer(0) */ + now = ub_get_timer(start); + printf("\ntime: now %lu\n\n", now); + + /* enumerate devices */ + printf("\n*** Enumerate devices ***\n"); + devs_no = ub_dev_enum(); + + printf("Number of devices found: %d\n", devs_no); + if (devs_no == 0) + return -1; + + + printf("\n*** Show devices ***\n"); + for (i = 0; i < devs_no; i++) { + test_dump_di(i); + printf("\n"); + } + + printf("\n*** Operations on devices ***\n"); + + /* test opening a device already opened */ + h = 0; + if ((rv = ub_dev_open(h)) != 0) { + errf("open device %d error %d\n", h, rv); + return -1; + } + if ((rv = ub_dev_open(h)) != 0) + errf("open device %d error %d\n", h, rv); + + ub_dev_close(h); + + /* test storage */ + printf("Trying storage devices...\n"); + for (i = 0; i < devs_no; i++) { + di = ub_dev_get(i); + + if (di->type & DEV_TYP_STOR) + break; + + } + if (i == devs_no) + printf("No storage devices available\n"); + else { + if ((rv = ub_dev_open(i)) != 0) + errf("open device %d error %d\n", i, rv); + else if ((rv = ub_dev_read(i, &buf, 200, 20)) != 0) + errf("could not read from device %d, error %d\n", i, rv); + + ub_dev_close(i); + } + + /* test networking */ + printf("Trying network devices...\n"); + for (i = 0; i < devs_no; i++) { + di = ub_dev_get(i); + + if (di->type == DEV_TYP_NET) + break; + + } + if (i == devs_no) + printf("No network devices available\n"); + else { + if ((rv = ub_dev_open(i)) != 0) + errf("open device %d error %d\n", i, rv); + else if ((rv = ub_dev_send(i, &buf, 2048)) != 0) + errf("could not send to device %d, error %d\n", i, rv); + + ub_dev_close(i); + } + + if (ub_dev_close(h) != 0) + errf("could not close device %d\n", h); + + printf("\n*** Env vars ***\n"); + + printf("ethact = %s\n", ub_env_get("ethact")); + printf("old fileaddr = %s\n", ub_env_get("fileaddr")); + ub_env_set("fileaddr", "deadbeef"); + printf("new fileaddr = %s\n", ub_env_get("fileaddr")); + + const char *env = NULL; + + while ((env = ub_env_enum(env)) != NULL) + printf("%s = %s\n", env, ub_env_get(env)); + + /* reset */ + ub_reset(); + printf("\nHmm, reset returned...?!\n"); + + return rv; +} + +void test_dump_sig(struct api_signature *sig) +{ + printf("signature:\n"); + printf(" version\t= %d\n", sig->version); + printf(" checksum\t= 0x%08x\n", sig->checksum); + printf(" sc entry\t= 0x%08x\n", sig->syscall); +} + +void test_dump_si(struct sys_info *si) +{ + int i; + + printf("sys info:\n"); + printf(" clkbus\t= 0x%08x\n", si->clk_bus); + printf(" clkcpu\t= 0x%08x\n", si->clk_cpu); + printf(" bar\t\t= 0x%08x\n", si->bar); + + printf("---\n"); + for (i = 0; i < si->mr_no; i++) { + if (si->mr[i].flags == 0) + break; + + printf(" start\t= 0x%08lx\n", si->mr[i].start); + printf(" size\t= 0x%08lx\n", si->mr[i].size); + + switch(si->mr[i].flags & 0x000F) { + case MR_ATTR_FLASH: + printf(" type FLASH\n"); + break; + case MR_ATTR_DRAM: + printf(" type DRAM\n"); + break; + case MR_ATTR_SRAM: + printf(" type SRAM\n"); + break; + default: + printf(" type UNKNOWN\n"); + } + printf("---\n"); + } +} + +static char * test_stor_typ(int type) +{ + if (type & DT_STOR_IDE) + return "IDE"; + + if (type & DT_STOR_SCSI) + return "SCSI"; + + if (type & DT_STOR_USB) + return "USB"; + + if (type & DT_STOR_MMC); + return "MMC"; + + return "Unknown"; +} + +void test_dump_di(int handle) +{ + int i; + struct device_info *di = ub_dev_get(handle); + + printf("device info (%d):\n", handle); + printf(" cookie\t= 0x%08x\n", (uint32_t)di->cookie); + printf(" type\t\t= 0x%08x\n", di->type); + + if (di->type == DEV_TYP_NET) { + printf(" hwaddr\t= "); + for (i = 0; i < 6; i++) + printf("%02x ", di->di_net.hwaddr[i]); + + printf("\n"); + + } else if (di->type & DEV_TYP_STOR) { + printf(" type\t\t= %s\n", test_stor_typ(di->type)); + printf(" blk size\t\t= %d\n", di->di_stor.block_size); + printf(" blk count\t\t= %d\n", di->di_stor.block_count); + } +} diff --git a/api_examples/glue.c b/api_examples/glue.c new file mode 100644 index 00000000000..75983691fde --- /dev/null +++ b/api_examples/glue.c @@ -0,0 +1,405 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include + +#include "glue.h" + +static int valid_sig(struct api_signature *sig) +{ + uint32_t checksum; + struct api_signature s; + + if (sig == NULL) + return 0; + /* + * Clear the checksum field (in the local copy) so as to calculate the + * CRC with the same initial contents as at the time when the sig was + * produced + */ + s = *sig; + s.checksum = 0; + + checksum = crc32(0, (unsigned char *)&s, sizeof(struct api_signature)); + + if (checksum != sig->checksum) + return 0; + + return 1; +} + +/* + * Searches for the U-Boot API signature + * + * returns 1/0 depending on found/not found result + */ +int api_search_sig(struct api_signature **sig) { + + unsigned char *sp; + + if (sig == NULL) + return 0; + + sp = (unsigned char *)API_SEARCH_START; + + while ((sp + (int)API_SIG_MAGLEN) < (unsigned char *)API_SEARCH_END) { + if (!memcmp(sp, API_SIG_MAGIC, API_SIG_MAGLEN)) { + *sig = (struct api_signature *)sp; + if (valid_sig(*sig)) + return 1; + } + sp += API_SIG_MAGLEN; + } + + *sig = NULL; + return 0; +} + +/**************************************** + * + * console + * + ****************************************/ + +int ub_getc(void) +{ + int c; + + if (!syscall(API_GETC, NULL, (uint32_t)&c)) + return -1; + + return c; +} + +int ub_tstc(void) +{ + int t; + + if (!syscall(API_TSTC, NULL, (uint32_t)&t)) + return -1; + + return t; +} + +void ub_putc(char c) +{ + syscall(API_PUTC, NULL, (uint32_t)&c); +} + +void ub_puts(const char *s) +{ + syscall(API_PUTS, NULL, (uint32_t)s); +} + +/**************************************** + * + * system + * + ****************************************/ + +void ub_reset(void) +{ + syscall(API_RESET, NULL); +} + +#define MR_MAX 5 +static struct mem_region mr[MR_MAX]; +static struct sys_info si; + +struct sys_info * ub_get_sys_info(void) +{ + int err = 0; + + memset(&si, 0, sizeof(struct sys_info)); + si.mr = mr; + si.mr_no = MR_MAX; + memset(&mr, 0, sizeof(mr)); + + if (!syscall(API_GET_SYS_INFO, &err, (u_int32_t)&si)) + return NULL; + + return ((err) ? NULL : &si); +} + +/**************************************** + * + * timing + * + ****************************************/ + +void ub_udelay(unsigned long usec) +{ + syscall(API_UDELAY, NULL, &usec); +} + +unsigned long ub_get_timer(unsigned long base) +{ + unsigned long cur; + + if (!syscall(API_GET_TIMER, NULL, &cur, &base)) + return 0; + + return cur; +} + + +/**************************************************************************** + * + * devices + * + * Devices are identified by handles: numbers 0, 1, 2, ..., MAX_DEVS-1 + * + ***************************************************************************/ + +#define MAX_DEVS 6 + +static struct device_info devices[MAX_DEVS]; + +struct device_info * ub_dev_get(int i) +{ + return ((i < 0 || i >= MAX_DEVS) ? NULL : &devices[i]); +} + +/* + * Enumerates the devices: fills out device_info elements in the devices[] + * array. + * + * returns: number of devices found + */ +int ub_dev_enum(void) +{ + struct device_info *di; + int n = 0; + + memset(&devices, 0, sizeof(struct device_info) * MAX_DEVS); + di = &devices[0]; + + if (!syscall(API_DEV_ENUM, NULL, di)) + return 0; + + while (di->cookie != NULL) { + + if (++n >= MAX_DEVS) + break; + + /* take another device_info */ + di++; + + /* pass on the previous cookie */ + di->cookie = devices[n - 1].cookie; + + if (!syscall(API_DEV_ENUM, NULL, di)) + return 0; + } + + return n; +} + +/* + * handle: 0-based id of the device + * + * returns: 0 when OK, err otherwise + */ +int ub_dev_open(int handle) +{ + struct device_info *di; + int err = 0; + + if (handle < 0 || handle >= MAX_DEVS) + return API_EINVAL; + + di = &devices[handle]; + + if (!syscall(API_DEV_OPEN, &err, di)) + return -1; + + return err; +} + +int ub_dev_close(int handle) +{ + struct device_info *di; + + if (handle < 0 || handle >= MAX_DEVS) + return API_EINVAL; + + di = &devices[handle]; + if (!syscall(API_DEV_CLOSE, NULL, di)) + return -1; + + return 0; +} + +/* + * + * Validates device for read/write, it has to: + * + * - have sane handle + * - be opened + * + * returns: 0/1 accordingly + */ +static int dev_valid(int handle) +{ + if (handle < 0 || handle >= MAX_DEVS) + return 0; + + if (devices[handle].state != DEV_STA_OPEN) + return 0; + + return 1; +} + +static int dev_stor_valid(int handle) +{ + if (!dev_valid(handle)) + return 0; + + if (!(devices[handle].type & DEV_TYP_STOR)) + return 0; + + return 1; +} + +int ub_dev_read(int handle, void *buf, lbasize_t len, lbastart_t start) +{ + struct device_info *di; + lbasize_t act_len; + int err = 0; + + if (!dev_stor_valid(handle)) + return API_ENODEV; + + di = &devices[handle]; + if (!syscall(API_DEV_READ, &err, di, buf, &len, &start, &act_len)) + return -1; + + if (err) + return err; + + if (act_len != len) + return API_EIO; + + return 0; +} + +static int dev_net_valid(int handle) +{ + if (!dev_valid(handle)) + return 0; + + if (devices[handle].type != DEV_TYP_NET) + return 0; + + return 1; +} + +int ub_dev_recv(int handle, void *buf, int len) +{ + struct device_info *di; + int err = 0, act_len; + + if (!dev_net_valid(handle)) + return API_ENODEV; + + di = &devices[handle]; + if (!syscall(API_DEV_READ, &err, di, buf, &len, &act_len)) + return -1; + + if (err) + return -1; + + return act_len; +} + +int ub_dev_send(int handle, void *buf, int len) +{ + struct device_info *di; + int err = 0; + + if (!dev_net_valid(handle)) + return API_ENODEV; + + di = &devices[handle]; + if (!syscall(API_DEV_WRITE, &err, di, buf, &len)) + return -1; + + return err; +} + +/**************************************** + * + * env vars + * + ****************************************/ + +char * ub_env_get(const char *name) +{ + char *value; + + if (!syscall(API_ENV_GET, NULL, (uint32_t)name, (uint32_t)&value)) + return NULL; + + return value; +} + +void ub_env_set(const char *name, char *value) +{ + syscall(API_ENV_SET, NULL, (uint32_t)name, (uint32_t)value); +} + + +static char env_name[256]; + +const char * ub_env_enum(const char *last) +{ + const char *env, *str; + int i; + + env = NULL; + + /* + * It's OK to pass only the name piece as last (and not the whole + * 'name=val' string), since the API_ENUM_ENV call uses envmatch() + * internally, which handles such case + */ + if (!syscall(API_ENV_ENUM, NULL, (uint32_t)last, (uint32_t)&env)) + return NULL; + + if (!env) + /* no more env. variables to enumerate */ + return NULL; + + /* next enumerated env var */ + memset(env_name, 0, 256); + for (i = 0, str = env; *str != '=' && *str != '\0';) + env_name[i++] = *str++; + + env_name[i] = '\0'; + + return env_name; +} diff --git a/api_examples/glue.h b/api_examples/glue.h new file mode 100644 index 00000000000..a82f783cbe0 --- /dev/null +++ b/api_examples/glue.h @@ -0,0 +1,76 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +/* + * This is the header file for conveniency wrapper routines (API glue) + */ + +#ifndef _API_GLUE_H_ +#define _API_GLUE_H_ + +#define API_SEARCH_START (255 * 1024 * 1024) /* start at 1MB below top RAM */ +#define API_SEARCH_END (256 * 1024 * 1024 - 1) /* ...and search to the end */ + +int syscall(int, int *, ...); +void * syscall_ptr; + +int api_search_sig(struct api_signature **sig); + +/* + * ub_ library calls are part of the application, not U-Boot code! They are + * front-end wrappers that are used by the consumer application: they prepare + * arguments for particular syscall and jump to the low level syscall() + */ + +/* console */ +int ub_getc(void); +int ub_tstc(void); +void ub_putc(char c); +void ub_puts(const char *s); + +/* system */ +void ub_reset(void); +struct sys_info * ub_get_sys_info(void); + +/* time */ +void ub_udelay(unsigned long); +unsigned long ub_get_timer(unsigned long); + +/* env vars */ +char * ub_env_get(const char *name); +void ub_env_set(const char *name, char *value); +const char * ub_env_enum(const char *last); + +/* devices */ +int ub_dev_enum(void); +int ub_dev_open(int handle); +int ub_dev_close(int handle); +int ub_dev_read(int handle, void *buf, + lbasize_t len, lbastart_t start); +int ub_dev_send(int handle, void *buf, int len); +int ub_dev_recv(int handle, void *buf, int len); +struct device_info * ub_dev_get(int); + +#endif /* _API_GLUE_H_ */ diff --git a/api_examples/libgenwrap.c b/api_examples/libgenwrap.c new file mode 100644 index 00000000000..df62633ca70 --- /dev/null +++ b/api_examples/libgenwrap.c @@ -0,0 +1,90 @@ +/* + * (C) Copyright 2007 Semihalf + * + * Written by: Rafal Jaworowski + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + * + * This is is a set of wrappers/stubs that allow to use certain routines from + * U-Boot's lib_generic in the standalone app. This way way we can re-use + * existing code e.g. operations on strings and similar. + * + */ + +#include +#include +#include + +#include "glue.h" + +/* + * printf() and vprintf() are stolen from u-boot/common/console.c + */ +void printf (const char *fmt, ...) +{ + va_list args; + uint i; + char printbuffer[256]; + + va_start (args, fmt); + + /* For this to work, printbuffer must be larger than + * anything we ever want to print. + */ + i = vsprintf (printbuffer, fmt, args); + va_end (args); + + /* Print the string */ + ub_puts (printbuffer); +} + +void vprintf (const char *fmt, va_list args) +{ + uint i; + char printbuffer[256]; + + /* For this to work, printbuffer must be larger than + * anything we ever want to print. + */ + i = vsprintf (printbuffer, fmt, args); + + /* Print the string */ + ub_puts (printbuffer); +} + +void putc (const char c) +{ + ub_putc(c); +} + +void udelay(unsigned long usec) +{ + ub_udelay(usec); +} + +void do_reset (void) +{ + ub_reset(); +} + +void *malloc(size_t len) +{ + return NULL; +} diff --git a/include/api_public.h b/include/api_public.h new file mode 100644 index 00000000000..690975ee40d --- /dev/null +++ b/include/api_public.h @@ -0,0 +1,102 @@ +#ifndef _API_PUBLIC_H_ +#define _API_PUBLIC_H_ + +#define API_EINVAL 1 /* invalid argument(s) */ +#define API_ENODEV 2 /* no device */ +#define API_ENOMEM 3 /* no memory */ +#define API_EBUSY 4 /* busy, occupied etc. */ +#define API_EIO 5 /* I/O error */ + +typedef int (*scp_t)(int, int *, ...); + +#define API_SIG_VERSION 1 +#define API_SIG_MAGIC "UBootAPI" +#define API_SIG_MAGLEN 8 + +struct api_signature { + char magic[API_SIG_MAGLEN]; /* magic string */ + uint16_t version; /* API version */ + uint32_t checksum; /* checksum of this sig struct */ + scp_t syscall; /* entry point to the API */ +}; + +enum { + API_RSVD = 0, + API_GETC, + API_PUTC, + API_TSTC, + API_PUTS, + API_RESET, + API_GET_SYS_INFO, + API_UDELAY, + API_GET_TIMER, + API_DEV_ENUM, + API_DEV_OPEN, + API_DEV_CLOSE, + API_DEV_READ, + API_DEV_WRITE, + API_ENV_ENUM, + API_ENV_GET, + API_ENV_SET, + API_MAXCALL +}; + +#define MR_ATTR_FLASH 0x0001 +#define MR_ATTR_DRAM 0x0002 +#define MR_ATTR_SRAM 0x0003 + +struct mem_region { + unsigned long start; + unsigned long size; + int flags; +}; + +struct sys_info { + unsigned long clk_bus; + unsigned long clk_cpu; + unsigned long bar; + struct mem_region *mr; + int mr_no; /* number of memory regions */ +}; + +#undef CFG_64BIT_LBA +#ifdef CFG_64BIT_LBA +typedef u_int64_t lbasize_t; +#else +typedef unsigned long lbasize_t; +#endif +typedef unsigned long lbastart_t; + +#define DEV_TYP_NONE 0x0000 +#define DEV_TYP_NET 0x0001 + +#define DEV_TYP_STOR 0x0002 +#define DT_STOR_IDE 0x0010 +#define DT_STOR_SCSI 0x0020 +#define DT_STOR_USB 0x0040 +#define DT_STOR_MMC 0x0080 + +#define DEV_STA_CLOSED 0x0000 /* invalid, closed */ +#define DEV_STA_OPEN 0x0001 /* open i.e. active */ + +struct device_info { + int type; + void *cookie; + + union { + struct { + lbasize_t block_count; /* no of blocks */ + unsigned long block_size; /* size of one block */ + } storage; + + struct { + unsigned char hwaddr[6]; + } net; + } info; +#define di_stor info.storage +#define di_net info.net + + int state; +}; + +#endif /* _API_PUBLIC_H_ */ diff --git a/include/common.h b/include/common.h index da2f01b464d..169bd2cd949 100644 --- a/include/common.h +++ b/include/common.h @@ -279,6 +279,9 @@ int misc_init_r (void); /* common/exports.c */ void jumptable_init(void); +/* api/api.c */ +void api_init (void); + /* common/memsize.c */ long get_ram_size (volatile long *, long); diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 9aa67f93c0f..07197450666 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -928,6 +928,11 @@ void board_init_r (gd_t *id, ulong dest_addr) /* Initialize the jump table for applications */ jumptable_init (); +#if defined(CONFIG_API) + /* Initialize API */ + api_init (); +#endif + /* Initialize the console (after the relocation and devices init) */ console_init_r (); -- cgit v1.3.1 From 7817cb2083d982923752fe0f12b67c0e7c09a027 Mon Sep 17 00:00:00 2001 From: Marcel Ziswiler Date: Sun, 30 Dec 2007 03:30:46 +0100 Subject: fix comments with new drivers organization Signed-off-by: Marcel Ziswiler --- README | 4 ++-- board/sc3/sc3.c | 2 +- board/ssv/common/cmd_sled.c | 4 ++-- common/env_nand.c | 2 +- cpu/ppc4xx/4xx_pci.c | 2 +- doc/README.generic_usb_ohci | 2 +- doc/README.modnet50 | 4 ++-- drivers/mtd/nand/nand_util.c | 2 +- drivers/net/sk98lin/Makefile | 2 +- drivers/usb/isp116x-hcd.c | 2 +- drivers/usb/usbdcore_mpc8xx.c | 3 ++- drivers/video/cfb_console.c | 8 ++++---- fs/jffs2/jffs2_1pass.c | 2 +- include/configs/CATcenter.h | 2 +- include/configs/MPC8313ERDB.h | 2 +- include/configs/PPChameleonEVB.h | 2 +- include/configs/SX1.h | 2 +- include/configs/integratorcp.h | 2 +- include/configs/omap1510inn.h | 2 +- include/configs/omap2420h4.h | 2 +- include/configs/omap5912osk.h | 2 +- nand_spl/board/amcc/acadia/Makefile | 2 +- nand_spl/board/amcc/bamboo/Makefile | 2 +- nand_spl/board/amcc/sequoia/Makefile | 2 +- 24 files changed, 31 insertions(+), 30 deletions(-) (limited to 'include') diff --git a/README b/README index 9a8b3b903d1..57fc01a9096 100644 --- a/README +++ b/README @@ -924,7 +924,7 @@ The following options need to be configured: (i.e. setenv videomode 317; saveenv; reset;) - "videomode=bootargs" all the video parameters are parsed - from the bootargs. (See drivers/videomodes.c) + from the bootargs. (See drivers/video/videomodes.c) CONFIG_VIDEO_SED13806 @@ -1353,7 +1353,7 @@ The following options need to be configured: CONFIG_FSL_I2C Define this option if you want to use Freescale's I2C driver in - drivers/fsl_i2c.c. + drivers/i2c/fsl_i2c.c. - SPI Support: CONFIG_SPI diff --git a/board/sc3/sc3.c b/board/sc3/sc3.c index 363a77d8a4e..09407647ab1 100644 --- a/board/sc3/sc3.c +++ b/board/sc3/sc3.c @@ -757,7 +757,7 @@ static struct pci_config_table pci_solidcard3_config_table[] = }; /*-------------------------------------------------------------------------+ - | pci_init_board (Called from pci_init() in drivers/pci.c) + | pci_init_board (Called from pci_init() in drivers/pci/pci.c) | | Init the PCI part of the SolidCard III | diff --git a/board/ssv/common/cmd_sled.c b/board/ssv/common/cmd_sled.c index 713ed65568c..2208580faec 100644 --- a/board/ssv/common/cmd_sled.c +++ b/board/ssv/common/cmd_sled.c @@ -32,8 +32,8 @@ * !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! * !!!!! !!!!! * !!!!! Next type definition was coming from original !!!!! - * !!!!! status LED driver drivers/status_led.c and !!!!! - * !!!!! should exported for using here. !!!!! + * !!!!! status LED driver drivers/misc/status_led.c !!!!! + * !!!!! and should be exported for using it here. !!!!! * !!!!! !!!!! * !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! */ diff --git a/common/env_nand.c b/common/env_nand.c index 38a07f8993f..ce0a2514db4 100644 --- a/common/env_nand.c +++ b/common/env_nand.c @@ -57,7 +57,7 @@ int nand_legacy_rw (struct nand_chip* nand, int cmd, size_t start, size_t len, size_t * retlen, u_char * buf); -/* info for NAND chips, defined in drivers/nand/nand.c */ +/* info for NAND chips, defined in drivers/mtd/nand/nand.c */ extern nand_info_t nand_info[]; /* references to names in env_common.c */ diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c index a68c419b1ba..a5b9690bec3 100644 --- a/cpu/ppc4xx/4xx_pci.c +++ b/cpu/ppc4xx/4xx_pci.c @@ -339,7 +339,7 @@ void pci_405gp_init(struct pci_controller *hose) } /* - * drivers/pci.c skips every host bridge but the 405GP since it could + * drivers/pci/pci.c skips every host bridge but the 405GP since it could * be set as an Adapter. * * I (Andrew May) don't know what we should do here, but I don't want diff --git a/doc/README.generic_usb_ohci b/doc/README.generic_usb_ohci index 494dd1f5d92..c44c5014743 100644 --- a/doc/README.generic_usb_ohci +++ b/doc/README.generic_usb_ohci @@ -1,7 +1,7 @@ Notes on the the generic USB-OHCI driver ======================================== -This driver (drivers/usb_ohci.[ch]) is the result of the merge of +This driver (drivers/usb/usb_ohci.[ch]) is the result of the merge of various existing OHCI drivers that were basically identical beside cpu/board dependant initalization. This initalization has been moved into cpu/board directories and are called via the hooks below. diff --git a/doc/README.modnet50 b/doc/README.modnet50 index 30338ce8cc7..f7bb254e16d 100644 --- a/doc/README.modnet50 +++ b/doc/README.modnet50 @@ -51,8 +51,8 @@ board/modnet50/lowlevel_init.S .. memory setup for ModNET50 board/modnet50/flash.c .. flash routines board/modnet50/modnet50.c .. some board init stuff -drivers/netarm_eth.c .. ethernet driver for the NET+50 CPU -drivers/netarm_eth.h .. header for ethernet driver +drivers/net/netarm_eth.c .. ethernet driver for the NET+50 CPU +drivers/net/netarm_eth.h .. header for ethernet driver include/configs/modnet50.h .. configuration file for ModNET50 diff --git a/drivers/mtd/nand/nand_util.c b/drivers/mtd/nand/nand_util.c index 4fd4e166e6a..6c5624a49a4 100644 --- a/drivers/mtd/nand/nand_util.c +++ b/drivers/mtd/nand/nand_util.c @@ -1,5 +1,5 @@ /* - * drivers/nand/nand_util.c + * drivers/mtd/nand/nand_util.c * * Copyright (C) 2006 by Weiss-Electronic GmbH. * All rights reserved. diff --git a/drivers/net/sk98lin/Makefile b/drivers/net/sk98lin/Makefile index a7d4a3b7a7e..8b83faeb15e 100644 --- a/drivers/net/sk98lin/Makefile +++ b/drivers/net/sk98lin/Makefile @@ -20,7 +20,7 @@ # Foundation, Inc., 59 Temple Place, Suite 330, Boston, # MA 02111-1307 USA # -# File: drivers/sk98lin/Makefile +# File: drivers/net/sk98lin/Makefile # # Makefile for the SysKonnect SK-98xx device driver. # diff --git a/drivers/usb/isp116x-hcd.c b/drivers/usb/isp116x-hcd.c index b21af10d0ba..ac6703056c9 100644 --- a/drivers/usb/isp116x-hcd.c +++ b/drivers/usb/isp116x-hcd.c @@ -20,7 +20,7 @@ * MA 02111-1307 USA * * - * Derived in part from the SL811 HCD driver "u-boot/drivers/sl811_usb.c" + * Derived in part from the SL811 HCD driver "u-boot/drivers/usb/sl811_usb.c" * (original copyright message follows): * * (C) Copyright 2004 diff --git a/drivers/usb/usbdcore_mpc8xx.c b/drivers/usb/usbdcore_mpc8xx.c index d4c40965656..122793c023c 100644 --- a/drivers/usb/usbdcore_mpc8xx.c +++ b/drivers/usb/usbdcore_mpc8xx.c @@ -3,7 +3,8 @@ * bodonoghue@CodeHermit.ie * * References - * DasUBoot/drivers/usbdcore_omap1510.c, for design and implementation ideas. + * DasUBoot/drivers/usb/usbdcore_omap1510.c, for design and implementation + * ideas. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/drivers/video/cfb_console.c b/drivers/video/cfb_console.c index bcf877194e0..82cc0c76c30 100644 --- a/drivers/video/cfb_console.c +++ b/drivers/video/cfb_console.c @@ -187,9 +187,9 @@ CONFIG_VIDEO_HW_CURSOR: - Uses the hardware cursor capability of the /*****************************************************************************/ /* Cursor definition: */ -/* CONFIG_CONSOLE_CURSOR: Uses a timer function (see drivers/i8042.c) to */ -/* let the cursor blink. Uses the macros CURSOR_OFF */ -/* and CURSOR_ON. */ +/* CONFIG_CONSOLE_CURSOR: Uses a timer function (see drivers/input/i8042.c) */ +/* to let the cursor blink. Uses the macros */ +/* CURSOR_OFF and CURSOR_ON. */ /* CONFIG_VIDEO_SW_CURSOR: Draws a cursor after the last character. No */ /* blinking is provided. Uses the macros CURSOR_SET */ /* and CURSOR_OFF. */ @@ -217,7 +217,7 @@ void console_cursor (int state); #define CURSOR_OFF console_cursor(0); #define CURSOR_SET #ifndef CONFIG_I8042_KBD -#warning Cursor drawing on/off needs timer function s.a. drivers/i8042.c +#warning Cursor drawing on/off needs timer function s.a. drivers/input/i8042.c #endif #else #ifdef CONFIG_CONSOLE_TIME diff --git a/fs/jffs2/jffs2_1pass.c b/fs/jffs2/jffs2_1pass.c index 53166683fd0..69f53eabcf0 100644 --- a/fs/jffs2/jffs2_1pass.c +++ b/fs/jffs2/jffs2_1pass.c @@ -165,7 +165,7 @@ static struct part_info *current_part; int read_jffs2_nand(size_t start, size_t len, size_t * retlen, u_char * buf, int nanddev); #else -/* info for NAND chips, defined in drivers/nand/nand.c */ +/* info for NAND chips, defined in drivers/mtd/nand/nand.c */ extern nand_info_t nand_info[]; #endif diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h index 0321650f3d2..1603c9c0bda 100644 --- a/include/configs/CATcenter.h +++ b/include/configs/CATcenter.h @@ -473,7 +473,7 @@ #define CONFIG_VGA_AS_SINGLE_DEVICE /* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ #define CFG_ISA_IO 0xE8000000 -/* see also drivers/videomodes.c */ +/* see also drivers/video/videomodes.c */ #define CFG_DEFAULT_VIDEO_MODE 0x303 #endif diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index c9a9c83f220..7bc4e274367 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -192,7 +192,7 @@ #define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */ -/* drivers/nand/nand.c */ +/* drivers/mtd/nand/nand.c */ #define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */ #define CFG_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index c2aa2cc0984..cf98324344c 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -496,7 +496,7 @@ #define CONFIG_VGA_AS_SINGLE_DEVICE /* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ #define CFG_ISA_IO 0xE8000000 -/* see also drivers/videomodes.c */ +/* see also drivers/video/videomodes.c */ #define CFG_DEFAULT_VIDEO_MODE 0x303 #endif diff --git a/include/configs/SX1.h b/include/configs/SX1.h index 05cef873e5f..50ad7dd598d 100644 --- a/include/configs/SX1.h +++ b/include/configs/SX1.h @@ -181,7 +181,7 @@ * FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ #define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ diff --git a/include/configs/integratorcp.h b/include/configs/integratorcp.h index 69310d4dfbc..e1d1483b719 100644 --- a/include/configs/integratorcp.h +++ b/include/configs/integratorcp.h @@ -168,7 +168,7 @@ SIB at Block62 End Block62 address 0x24f80000 /* * Move up the U-Boot & monitor area if more flash is fitted. * If this U-Boot is to be run on Integrators with varying flash sizes, - * drivers/cfi_flash.c::flash_init() can read the Integrator CP_FLASHPROG + * drivers/mtd/cfi_flash.c::flash_init() can read the Integrator CP_FLASHPROG * register and dynamically assign CFG_ENV_ADDR & CFG_MONITOR_BASE * - CFG_MONITOR_BASE is set to indicate that the environment is not * embedded in the boot monitor(s) area diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h index 8623ed3cc88..0be46eacec7 100644 --- a/include/configs/omap1510inn.h +++ b/include/configs/omap1510inn.h @@ -179,7 +179,7 @@ * FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ #define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ diff --git a/include/configs/omap2420h4.h b/include/configs/omap2420h4.h index 8ae8efeb817..88a3f6eb95b 100644 --- a/include/configs/omap2420h4.h +++ b/include/configs/omap2420h4.h @@ -283,7 +283,7 @@ * CFI FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ #define CFG_FLASH_PROTECTION 1 /* Use hardware sector protection */ diff --git a/include/configs/omap5912osk.h b/include/configs/omap5912osk.h index 16ce2f61aec..e3bde4ff81d 100644 --- a/include/configs/omap5912osk.h +++ b/include/configs/omap5912osk.h @@ -174,7 +174,7 @@ * FLASH driver setup */ #define CFG_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ #define CFG_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } diff --git a/nand_spl/board/amcc/acadia/Makefile b/nand_spl/board/amcc/acadia/Makefile index 6e53bea0179..4272108b510 100644 --- a/nand_spl/board/amcc/acadia/Makefile +++ b/nand_spl/board/amcc/acadia/Makefile @@ -97,7 +97,7 @@ $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c -# from drivers/nand directory +# from drivers/mtd/nand directory $(obj)nand_ecc.c: @rm -f $(obj)nand_ecc.c ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $(obj)nand_ecc.c diff --git a/nand_spl/board/amcc/bamboo/Makefile b/nand_spl/board/amcc/bamboo/Makefile index 3a633fb8871..aed79607090 100644 --- a/nand_spl/board/amcc/bamboo/Makefile +++ b/nand_spl/board/amcc/bamboo/Makefile @@ -79,7 +79,7 @@ $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c -# from drivers/nand directory +# from drivers/mtd/nand directory $(obj)nand_ecc.c: @rm -f $(obj)nand_ecc.c ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $(obj)nand_ecc.c diff --git a/nand_spl/board/amcc/sequoia/Makefile b/nand_spl/board/amcc/sequoia/Makefile index dfa0ce39e82..93150aad1be 100644 --- a/nand_spl/board/amcc/sequoia/Makefile +++ b/nand_spl/board/amcc/sequoia/Makefile @@ -89,7 +89,7 @@ $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c -# from drivers/nand directory +# from drivers/mtd/nand directory $(obj)nand_ecc.c: @rm -f $(obj)nand_ecc.c ln -s $(SRCTREE)/drivers/mtd/nand/nand_ecc.c $(obj)nand_ecc.c -- cgit v1.3.1 From 10c7382bc5d5e64c47f94ac2ca78cc574442e82d Mon Sep 17 00:00:00 2001 From: Marcel Ziswiler Date: Sun, 30 Dec 2007 03:30:56 +0100 Subject: fix various comments Signed-off-by: Marcel Ziswiler --- cpu/pxa/start.S | 38 +++++++++++++++++++------------------- doc/README.nand | 2 +- drivers/net/ne2000.c | 7 +++---- include/linux/mtd/nand.h | 2 +- nand_spl/nand_boot.c | 2 +- 5 files changed, 25 insertions(+), 26 deletions(-) (limited to 'include') diff --git a/cpu/pxa/start.S b/cpu/pxa/start.S index b922485ed33..31f408dfa72 100644 --- a/cpu/pxa/start.S +++ b/cpu/pxa/start.S @@ -57,7 +57,7 @@ _fiq: .word fiq * Startup Code (reset vector) * * do important init only if we don't start from RAM! - * - relocate armboot to ram + * - relocate armboot to RAM * - setup stack * - jump to second stage */ @@ -90,7 +90,7 @@ IRQ_STACK_START: .globl FIQ_STACK_START FIQ_STACK_START: .word 0x0badc0de -#endif +#endif /* CONFIG_USE_IRQ */ /****************************************************************************/ @@ -100,18 +100,18 @@ FIQ_STACK_START: /****************************************************************************/ reset: - mrs r0,cpsr /* set the cpu to SVC32 mode */ + mrs r0,cpsr /* set the CPU to SVC32 mode */ bic r0,r0,#0x1f /* (superviser mode, M=10011) */ orr r0,r0,#0x13 msr cpsr,r0 /* * we do sys-critical inits only at reboot, - * not when booting from ram! + * not when booting from RAM! */ #ifndef CONFIG_SKIP_LOWLEVEL_INIT bl cpu_init_crit /* we do sys-critical inits */ -#endif +#endif /* !CONFIG_SKIP_LOWLEVEL_INIT */ #ifndef CONFIG_SKIP_RELOCATE_UBOOT relocate: /* relocate U-Boot to RAM */ @@ -130,7 +130,7 @@ copy_loop: stmia r1!, {r3-r10} /* copy to target address [r1] */ cmp r0, r2 /* until source end addreee [r2] */ ble copy_loop -#endif /* CONFIG_SKIP_RELOCATE_UBOOT */ +#endif /* !CONFIG_SKIP_RELOCATE_UBOOT */ /* Set up the stack */ stack_setup: @@ -139,7 +139,7 @@ stack_setup: sub r0, r0, #CFG_GBL_DATA_SIZE /* bdinfo */ #ifdef CONFIG_USE_IRQ sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) -#endif +#endif /* CONFIG_USE_IRQ */ sub sp, r0, #12 /* leave 3 words for abort-stack */ clear_bss: @@ -172,11 +172,11 @@ _start_armboot: .word start_armboot #undef OSCR #undef OWER #undef OIER -#endif +#endif /* CONFIG_PXA250 || CONFIG_CPU_MONAHANS */ #ifdef CONFIG_PXA250 #undef RCSR #undef CCCR -#endif +#endif /* CONFIG_PXA250 */ /* Interrupt-Controller base address */ IC_BASE: .word 0x40d00000 @@ -197,18 +197,18 @@ OSTIMER_BASE: .word 0x40a00000 #ifdef CONFIG_CPU_MONAHANS # ifndef CFG_MONAHANS_RUN_MODE_OSC_RATIO # error "You have to define CFG_MONAHANS_RUN_MODE_OSC_RATIO!!" -# endif +# endif /* !CFG_MONAHANS_RUN_MODE_OSC_RATIO */ # ifndef CFG_MONAHANS_TURBO_RUN_MODE_RATIO # define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 0x1 -# endif -#else /* ! CONFIG_CPU_MONAHANS */ +# endif /* !CFG_MONAHANS_TURBO_RUN_MODE_RATIO */ +#else /* !CONFIG_CPU_MONAHANS */ #ifdef CFG_CPUSPEED CC_BASE: .word 0x41300000 #define CCCR 0x00 cpuspeed: .word CFG_CPUSPEED -#else +#else /* !CFG_CPUSPEED */ #error "You have to define CFG_CPUSPEED!!" -#endif +#endif /* CFG_CPUSPEED */ #endif /* CONFIG_CPU_MONAHANS */ /* takes care the CP15 update has taken place */ @@ -225,7 +225,7 @@ cpu_init_crit: ldr r0, IC_BASE mov r1, #0x00 str r1, [r0, #ICMR] -#else +#else /* CONFIG_CPU_MONAHANS */ /* Step 1 - Enable CP6 permission */ mrc p15, 0, r1, c15, c1, 0 @ read CPAR orr r1, r1, #0x40 @@ -244,14 +244,14 @@ cpu_init_crit: ldr r1, =CKENB ldr r2, =(CKENB_6_IRQ) str r2, [r1] -#endif +#endif /* !CONFIG_CPU_MONAHANS */ /* set clock speed */ #ifdef CONFIG_CPU_MONAHANS ldr r0, =ACCR ldr r1, =(((CFG_MONAHANS_TURBO_RUN_MODE_RATIO<<8) & ACCR_XN_MASK) | (CFG_MONAHANS_RUN_MODE_OSC_RATIO & ACCR_XL_MASK)) str r1, [r0] -#else /* ! CONFIG_CPU_MONAHANS */ +#else /* !CONFIG_CPU_MONAHANS */ #ifdef CFG_CPUSPEED ldr r0, CC_BASE ldr r1, cpuspeed @@ -451,7 +451,7 @@ fiq: bl do_fiq /* effiction fiq_save_user_regs */ irq_restore_user_regs -#else +#else /* !CONFIG_USE_IRQ */ .align 5 irq: @@ -465,7 +465,7 @@ fiq: bad_save_user_regs bl do_fiq -#endif +#endif /* CONFIG_USE_IRQ */ /****************************************************************************/ /* */ diff --git a/doc/README.nand b/doc/README.nand index c5c5ef29e63..647a6b8e67f 100644 --- a/doc/README.nand +++ b/doc/README.nand @@ -79,7 +79,7 @@ Commands: nand write.jffs2 addr ofs|partition size Like `write', but blocks that are marked bad are skipped and the - is written to the next block instead. This allows writing writing + data is written to the next block instead. This allows writing a JFFS2 image, as long as the image is short enough to fit even after skipping the bad blocks. Compact images, such as those produced by mkfs.jffs2 should work well, but loading an image copied diff --git a/drivers/net/ne2000.c b/drivers/net/ne2000.c index c978d62ef30..b1006575394 100644 --- a/drivers/net/ne2000.c +++ b/drivers/net/ne2000.c @@ -839,7 +839,7 @@ void uboot_push_packet_len(int len) { } dp83902a_recv(&pbuf[0], len); - /*Just pass it to the upper layer*/ + /* Just pass it to the upper layer */ NetReceive(&pbuf[0], len); } @@ -902,7 +902,6 @@ int eth_init(bd_t *bd) { } void eth_halt() { - PRINTK("### eth_halt\n"); if(initialized) dp83902a_stop(); @@ -910,8 +909,8 @@ void eth_halt() { } int eth_rx() { -dp83902a_poll(); -return 1; + dp83902a_poll(); + return 1; } int eth_send(volatile void *packet, int length) { diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index 49ff80fd3aa..4cc4a7d1bb4 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -129,7 +129,7 @@ extern int nand_read_raw (struct mtd_info *mtd, uint8_t *buf, loff_t from, size_ #define NAND_ECC_HW3_256 2 /* Hardware ECC 3 byte ECC per 512 Byte data */ #define NAND_ECC_HW3_512 3 -/* Hardware ECC 3 byte ECC per 512 Byte data */ +/* Hardware ECC 6 byte ECC per 512 Byte data */ #define NAND_ECC_HW6_512 4 /* Hardware ECC 8 byte ECC per 512 Byte data */ #define NAND_ECC_HW8_512 6 diff --git a/nand_spl/nand_boot.c b/nand_spl/nand_boot.c index 840a5965967..e2147cb909b 100644 --- a/nand_spl/nand_boot.c +++ b/nand_spl/nand_boot.c @@ -73,7 +73,7 @@ static int nand_is_bad_block(struct mtd_info *mtd, int block) nand_command(mtd, block, 0, CFG_NAND_BAD_BLOCK_POS, NAND_CMD_READOOB); /* - * Read on byte + * Read one byte */ if (this->read_byte(mtd) != 0xff) return 1; -- cgit v1.3.1 From 7ca90513486abd4ae50bd1b7403f47cc58c5ad25 Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Wed, 9 Jan 2008 01:15:25 +0100 Subject: trivial: fix consequences of a bad merge Fix what looks like a merge artifact. Signed-off-by: Guennadi Liakhovetski --- include/configs/M54455EVB.h | 1 - 1 file changed, 1 deletion(-) (limited to 'include') diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 35637f92c9f..211f11d6046 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -293,7 +293,6 @@ # define CFG_ENV_SECT_SIZE 0x20000 #endif -/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system /* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system keep reset. */ #undef CFG_FLASH_CFI -- cgit v1.3.1 From 6636b62a6efc7f14e6e788788631ae7a7fca4537 Mon Sep 17 00:00:00 2001 From: James Yang Date: Wed, 9 Jan 2008 11:17:49 -0600 Subject: Expose parse_line() globally. Add new function readline_into_buffer() that allows the output of readline to be put into a pointer to char buffer. This refactoring allows other functions besides the main command loop to also use the same input mechanism. Signed-off-by: James Yang Acked-by: Jon Loeliger --- common/main.c | 25 +++++++++++++++---------- include/common.h | 2 ++ 2 files changed, 17 insertions(+), 10 deletions(-) (limited to 'include') diff --git a/common/main.c b/common/main.c index 4253eac2d4f..ad2a386c865 100644 --- a/common/main.c +++ b/common/main.c @@ -59,7 +59,6 @@ extern int do_bootd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); #define MAX_DELAY_STOP_STR 32 -static int parse_line (char *, char *[]); #if defined(CONFIG_BOOTDELAY) && (CONFIG_BOOTDELAY >= 0) static int abortboot(int); #endif @@ -918,8 +917,15 @@ static int cread_line(const char *const prompt, char *buf, unsigned int *len) */ int readline (const char *const prompt) { + return readline_into_buffer(prompt, console_buffer); +} + + +int readline_into_buffer (const char *const prompt, char * buffer) +{ + char *p = buffer; + char * p_buf = p; #ifdef CONFIG_CMDLINE_EDITING - char *p = console_buffer; unsigned int len=MAX_CMDBUF_SIZE; int rc; static int initted = 0; @@ -934,7 +940,6 @@ int readline (const char *const prompt) rc = cread_line(prompt, p, &len); return rc < 0 ? rc : len; #else - char *p = console_buffer; int n = 0; /* buffer index */ int plen = 0; /* prompt length */ int col; /* output column cnt */ @@ -972,13 +977,13 @@ int readline (const char *const prompt) case '\n': *p = '\0'; puts ("\r\n"); - return (p - console_buffer); + return (p - p_buf); case '\0': /* nul */ continue; case 0x03: /* ^C - break */ - console_buffer[0] = '\0'; /* discard input */ + p_buf[0] = '\0'; /* discard input */ return (-1); case 0x15: /* ^U - erase line */ @@ -986,20 +991,20 @@ int readline (const char *const prompt) puts (erase_seq); --col; } - p = console_buffer; + p = p_buf; n = 0; continue; case 0x17: /* ^W - erase word */ - p=delete_char(console_buffer, p, &col, &n, plen); + p=delete_char(p_buf, p, &col, &n, plen); while ((n > 0) && (*p != ' ')) { - p=delete_char(console_buffer, p, &col, &n, plen); + p=delete_char(p_buf, p, &col, &n, plen); } continue; case 0x08: /* ^H - backspace */ case 0x7F: /* DEL - backspace */ - p=delete_char(console_buffer, p, &col, &n, plen); + p=delete_char(p_buf, p, &col, &n, plen); continue; default: @@ -1012,7 +1017,7 @@ int readline (const char *const prompt) /* if auto completion triggered just continue */ *p = '\0'; if (cmd_auto_complete(prompt, console_buffer, &n, &col)) { - p = console_buffer + n; /* reset */ + p = p_buf + n; /* reset */ continue; } #endif diff --git a/include/common.h b/include/common.h index 493417f8776..3b5bd8c52db 100644 --- a/include/common.h +++ b/include/common.h @@ -197,6 +197,8 @@ int print_buffer (ulong addr, void* data, uint width, uint count, uint linelen); void main_loop (void); int run_command (const char *cmd, int flag); int readline (const char *const prompt); +int readline_into_buffer (const char *const prompt, char * buffer); +int parse_line (char *, char *[]); void init_cmd_timeout(void); void reset_cmd_timeout(void); -- cgit v1.3.1 From 1d47273d46925929f8f2c1913cd96d7257aade88 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 18 Dec 2007 23:21:51 -0600 Subject: Use FSL Book-E MMU macros from Linux Kernel Grab the FSL Book-E MAS register macros from Linux. Also added defines for page sizes up to 4TB and removed SHAREN since it doesnt really exist. Signed-off-by: Kumar Gala --- include/asm-ppc/mmu.h | 100 ++++++++++++++++++++++++++------------------------ include/e500.h | 12 ++---- 2 files changed, 56 insertions(+), 56 deletions(-) (limited to 'include') diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h index b19abe73a09..fed4fd64a72 100644 --- a/include/asm-ppc/mmu.h +++ b/include/asm-ppc/mmu.h @@ -336,55 +336,57 @@ extern int write_bat(ppc_bat_t bat, unsigned long upper, unsigned long lower); */ /* - * e500 support + * FSL Book-E support */ -#define MAS0_TLBSEL 0x10000000 -#define MAS0_ESEL 0x000F0000 -#define MAS0_NV 0x00000001 - -#define MAS1_VALID 0x80000000 -#define MAS1_IPROT 0x40000000 -#define MAS1_TID 0x00FF0000 -#define MAS1_TS 0x00001000 -#define MAS1_TSIZE 0x00000F00 - -#define MAS2_EPN 0xFFFFF000 -#define MAS2_SHAREN 0x00000200 -#define MAS2_X0 0x00000040 -#define MAS2_X1 0x00000020 -#define MAS2_W 0x00000010 -#define MAS2_I 0x00000008 -#define MAS2_M 0x00000004 -#define MAS2_G 0x00000002 -#define MAS2_E 0x00000001 - -#define MAS3_RPN 0xFFFFF000 -#define MAS3_U0 0x00000200 -#define MAS3_U1 0x00000100 -#define MAS3_U2 0x00000080 -#define MAS3_U3 0x00000040 -#define MAS3_UX 0x00000020 -#define MAS3_SX 0x00000010 -#define MAS3_UW 0x00000008 -#define MAS3_SW 0x00000004 -#define MAS3_UR 0x00000002 -#define MAS3_SR 0x00000001 - -#define MAS4_TLBSELD 0x10000000 -#define MAS4_TIDDSEL 0x00030000 -#define MAS4_DSHAREN 0x00001000 -#define MAS4_TSIZED(x) (x << 8) -#define MAS4_X0D 0x00000040 -#define MAS4_X1D 0x00000020 -#define MAS4_WD 0x00000010 -#define MAS4_ID 0x00000008 -#define MAS4_MD 0x00000004 -#define MAS4_GD 0x00000002 -#define MAS4_ED 0x00000001 - -#define MAS6_SPID 0x00FF0000 -#define MAS6_SAS 0x00000001 +#define MAS0_TLBSEL(x) ((x << 28) & 0x30000000) +#define MAS0_ESEL(x) ((x << 16) & 0x0FFF0000) +#define MAS0_NV(x) ((x) & 0x00000FFF) + +#define MAS1_VALID 0x80000000 +#define MAS1_IPROT 0x40000000 +#define MAS1_TID(x) ((x << 16) & 0x3FFF0000) +#define MAS1_TS 0x00001000 +#define MAS1_TSIZE(x) ((x << 8) & 0x00000F00) + +#define MAS2_EPN 0xFFFFF000 +#define MAS2_X0 0x00000040 +#define MAS2_X1 0x00000020 +#define MAS2_W 0x00000010 +#define MAS2_I 0x00000008 +#define MAS2_M 0x00000004 +#define MAS2_G 0x00000002 +#define MAS2_E 0x00000001 + +#define MAS3_RPN 0xFFFFF000 +#define MAS3_U0 0x00000200 +#define MAS3_U1 0x00000100 +#define MAS3_U2 0x00000080 +#define MAS3_U3 0x00000040 +#define MAS3_UX 0x00000020 +#define MAS3_SX 0x00000010 +#define MAS3_UW 0x00000008 +#define MAS3_SW 0x00000004 +#define MAS3_UR 0x00000002 +#define MAS3_SR 0x00000001 + +#define MAS4_TLBSELD(x) MAS0_TLBSEL(x) +#define MAS4_TIDDSEL 0x000F0000 +#define MAS4_TSIZED(x) MAS1_TSIZE(x) +#define MAS4_X0D 0x00000040 +#define MAS4_X1D 0x00000020 +#define MAS4_WD 0x00000010 +#define MAS4_ID 0x00000008 +#define MAS4_MD 0x00000004 +#define MAS4_GD 0x00000002 +#define MAS4_ED 0x00000001 + +#define MAS6_SPID0 0x3FFF0000 +#define MAS6_SPID1 0x00007FFE +#define MAS6_SAS 0x00000001 +#define MAS6_SPID MAS6_SPID0 + +#define MAS7_RPN 0xFFFFFFFF #define BOOKE_PAGESZ_1K 0 #define BOOKE_PAGESZ_4K 1 @@ -398,6 +400,10 @@ extern int write_bat(ppc_bat_t bat, unsigned long upper, unsigned long lower); #define BOOKE_PAGESZ_256M 9 #define BOOKE_PAGESZ_1G 10 #define BOOKE_PAGESZ_4G 11 +#define BOOKE_PAGESZ_16GB 12 +#define BOOKE_PAGESZ_64GB 13 +#define BOOKE_PAGESZ_256GB 14 +#define BOOKE_PAGESZ_1TB 15 #if defined(CONFIG_MPC86xx) #define LAWBAR_BASE_ADDR 0x00FFFFFF diff --git a/include/e500.h b/include/e500.h index 0d73260f40c..983826d32cc 100644 --- a/include/e500.h +++ b/include/e500.h @@ -50,10 +50,7 @@ typedef struct * nv(Next victim):0,1 */ #define TLB1_MAS0(tlbsel,esel,nv) \ - ((((tlbsel) << 28) & MAS0_TLBSEL) |\ - (((esel) << 16) & MAS0_ESEL ) |\ - (nv) ) - + (MAS0_TLBSEL(tlbsel) | MAS0_ESEL(esel) | MAS0_NV(nv)) /* MAS1 * v(TLB valid bit):0,1 @@ -65,10 +62,9 @@ typedef struct #define TLB1_MAS1(v,iprot,tid,ts,tsize) \ ((((v) << 31) & MAS1_VALID) |\ (((iprot) << 30) & MAS1_IPROT) |\ - (((tid) << 16) & MAS1_TID) |\ + (MAS1_TID(tid)) |\ (((ts) << 12) & MAS1_TS) |\ - (((tsize) << 8) & MAS1_TSIZE) ) - + (MAS1_TSIZE(tsize))) /* MAS2 * epn(effective page number):20bits @@ -79,7 +75,6 @@ typedef struct */ #define TLB1_MAS2(epn,sharen,x0,x1,w,i,m,g,e) \ ((((epn) << 12) & MAS2_EPN) |\ - (((sharen) << 9) & MAS2_SHAREN) |\ (((x0) << 6) & MAS2_X0) |\ (((x1) << 5) & MAS2_X1) |\ (((w) << 4) & MAS2_W) |\ @@ -88,7 +83,6 @@ typedef struct (((g) << 1) & MAS2_G) |\ (e) ) - /* MAS3 * rpn(real page number):20bits * u0-u3(user bits, useful for page table management in OS):0,1 -- cgit v1.3.1 From 2146cf56821c3364786ca94a7306008c5824b238 Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Wed, 19 Dec 2007 01:18:15 -0600 Subject: Reworked FSL Book-E TLB macros to be more readable The old macros made it difficult to know what WIMGE and perm bits were set for a TLB entry. Actually use the bit masks for these items since they are only a single bit. Also moved the macros into mmu.h out of e500.h since they aren't specific to e500. Signed-off-by: Kumar Gala --- board/freescale/mpc8540ads/init.S | 145 +++++++++++++++++--------------------- board/freescale/mpc8541cds/init.S | 124 +++++++++++++++----------------- board/freescale/mpc8544ds/init.S | 117 ++++++++++++++---------------- board/freescale/mpc8548cds/init.S | 109 +++++++++++++--------------- board/freescale/mpc8555cds/init.S | 124 +++++++++++++++----------------- board/freescale/mpc8560ads/init.S | 144 +++++++++++++++++-------------------- board/freescale/mpc8568mds/init.S | 104 +++++++++++++-------------- board/mpc8540eval/init.S | 132 +++++++++++++++++----------------- board/pm854/init.S | 124 +++++++++++++++----------------- board/pm856/init.S | 124 +++++++++++++++----------------- board/sbc8560/init.S | 94 ++++++++++++------------ board/stxgp3/init.S | 144 +++++++++++++++++-------------------- board/stxssa/init.S | 110 +++++++++++++---------------- board/tqm85xx/init.S | 124 +++++++++++++++----------------- cpu/mpc85xx/spd_sdram.c | 23 +++--- include/asm-ppc/mmu.h | 13 ++++ include/e500.h | 88 ----------------------- 17 files changed, 809 insertions(+), 1034 deletions(-) (limited to 'include') diff --git a/board/freescale/mpc8540ads/init.S b/board/freescale/mpc8540ads/init.S index 544fde94c43..74d71c632a9 100644 --- a/board/freescale/mpc8540ads/init.S +++ b/board/freescale/mpc8540ads/init.S @@ -43,7 +43,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -75,10 +75,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -94,112 +94,99 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) - + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4*1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4*1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8*1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8*1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12*1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12*1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 0: 16M Non-cacheable, guarded * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 16K Non-cacheable, guarded * 0xf8000000 16K BCSR registers */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K) - .long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K) + .long FSL_BOOKE_MAS2(CFG_BCSR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BCSR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) /* @@ -211,17 +198,15 @@ tlb1_entry: * Likely it needs to be increased by two for these entries. */ #error("Update the number of table entries in tlb1_entry") - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1, 9, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 8, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1, 9, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE + 0x4000000, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE + 0x4000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/freescale/mpc8541cds/init.S b/board/freescale/mpc8541cds/init.S index 978bda5e4dc..8c8c087c4a3 100644 --- a/board/freescale/mpc8541cds/init.S +++ b/board/freescale/mpc8541cds/init.S @@ -42,7 +42,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -74,10 +74,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -93,33 +93,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -127,50 +119,46 @@ tlb1_entry: * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xa0000000 256M PCI2 MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xb0000000 256M PCI2 MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded @@ -178,28 +166,28 @@ tlb1_entry: * 0xe200_0000 16M PCI1 IO * 0xe300_0000 16M PCI2 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 1M Non-cacheable, guarded * 0xf8000000 1M CADMUS registers */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) - .long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CADMUS_BASE_ADDR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CADMUS_BASE_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) entry_end diff --git a/board/freescale/mpc8544ds/init.S b/board/freescale/mpc8544ds/init.S index 084d4b80d94..544dc07c8dc 100644 --- a/board/freescale/mpc8544ds/init.S +++ b/board/freescale/mpc8544ds/init.S @@ -40,7 +40,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -71,10 +71,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB0 16K Cacheable, guarded @@ -87,33 +87,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -121,68 +113,63 @@ tlb1_entry: * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000 * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_BOOT_BLOCK, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BOOT_BLOCK, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 1G Non-cacheable, guarded * 0x80000000 1G PCIE 8,9,a,b */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long FSL_BOOKE_MAS2(CFG_PCIE_PHYS, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCIE_PHYS, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI_PHYS, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI_PHYS, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI_PHYS + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI_PHYS + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe100_0000 255M PCI IO range */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #ifdef CFG_LBC_CACHE_BASE /* * TLB 5: 64M Cacheable, non-guarded */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_CACHE_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_CACHE_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif /* * TLB 6: 64M Non-cacheable, guarded * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_NONCACHE_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_LBC_NONCACHE_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) 2: entry_end diff --git a/board/freescale/mpc8548cds/init.S b/board/freescale/mpc8548cds/init.S index a83a0952c32..ed0fc44939d 100644 --- a/board/freescale/mpc8548cds/init.S +++ b/board/freescale/mpc8548cds/init.S @@ -41,7 +41,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -74,10 +74,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -93,33 +93,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, (MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -127,39 +119,36 @@ tlb1_entry: * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_BOOT_BLOCK, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BOOT_BLOCK, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 1G Non-cacheable, guarded * 0x80000000 1G PCI1/PCIE 8,9,a,b */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long FSL_BOOKE_MAS2(CFG_PCI_PHYS, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI_PHYS, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #ifdef CFG_RIO_MEM_PHYS /* * TLB 2: 256M Non-cacheable, guarded */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_PHYS), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_PHYS), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_PHYS, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_PHYS, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_PHYS + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_PHYS + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_PHYS + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_PHYS + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif /* * TLB 5: 64M Non-cacheable, guarded @@ -168,28 +157,28 @@ tlb1_entry: * 0xe210_0000 1M PCI2 IO * 0xe300_0000 1M PCIe IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_CACHE_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_CACHE_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 64M Non-cacheable, guarded * 0xf8000000 64M CADMUS registers, relocated L2SRAM */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_NONCACHE_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_LBC_NONCACHE_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) 2: entry_end diff --git a/board/freescale/mpc8555cds/init.S b/board/freescale/mpc8555cds/init.S index 978bda5e4dc..8c8c087c4a3 100644 --- a/board/freescale/mpc8555cds/init.S +++ b/board/freescale/mpc8555cds/init.S @@ -42,7 +42,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -74,10 +74,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -93,33 +93,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -127,50 +119,46 @@ tlb1_entry: * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xa0000000 256M PCI2 MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xb0000000 256M PCI2 MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded @@ -178,28 +166,28 @@ tlb1_entry: * 0xe200_0000 16M PCI1 IO * 0xe300_0000 16M PCI2 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 1M Non-cacheable, guarded * 0xf8000000 1M CADMUS registers */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) - .long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CADMUS_BASE_ADDR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CADMUS_BASE_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) entry_end diff --git a/board/freescale/mpc8560ads/init.S b/board/freescale/mpc8560ads/init.S index 544fde94c43..37fd0c6f488 100644 --- a/board/freescale/mpc8560ads/init.S +++ b/board/freescale/mpc8560ads/init.S @@ -43,7 +43,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -75,10 +75,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -94,33 +94,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -128,78 +120,74 @@ tlb1_entry: * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 16K Non-cacheable, guarded * 0xf8000000 16K BCSR registers */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K) - .long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16K) + .long FSL_BOOKE_MAS2(CFG_BCSR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BCSR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) /* @@ -211,17 +199,15 @@ tlb1_entry: * Likely it needs to be increased by two for these entries. */ #error("Update the number of table entries in tlb1_entry") - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1, 9, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 8, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1, 9, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE + 0x4000000, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE + 0x4000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/freescale/mpc8568mds/init.S b/board/freescale/mpc8568mds/init.S index e36036daf0d..2748c51f3bb 100644 --- a/board/freescale/mpc8568mds/init.S +++ b/board/freescale/mpc8568mds/init.S @@ -41,7 +41,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ #define entry_start \ @@ -73,10 +73,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -93,31 +93,25 @@ tlb1_entry: * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* TLB 1 Initializations */ /* @@ -125,31 +119,29 @@ tlb1_entry: * 0xff000000 16M FLASH (upper half) * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE + 0x1000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE + 0x1000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE + 0x1000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE + 0x1000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLBe 1: 16M Non-cacheable, guarded * 0xfe000000 16M FLASH (lower half) */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLBe 2: 1G Non-cacheable, guarded * 0x80000000 512M PCI1 MEM * 0xa0000000 512M PCIe MEM */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLBe 3: 64M Non-cacheable, guarded @@ -157,19 +149,19 @@ tlb1_entry: * 0xe200_0000 8M PCI1 IO * 0xe280_0000 8M PCIe IO */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLBe 4: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLBe 5: 256K Non-cacheable, guarded @@ -177,10 +169,10 @@ tlb1_entry: * 0xf8008000 32K PIB (CS4) * 0xf8010000 32K PIB (CS5) */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K) - .long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K) + .long FSL_BOOKE_MAS2(CFG_BCSR_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BCSR_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) 2: entry_end diff --git a/board/mpc8540eval/init.S b/board/mpc8540eval/init.S index 8c2ca65a91c..a8ac3fb8c7e 100644 --- a/board/mpc8540eval/init.S +++ b/board/mpc8540eval/init.S @@ -46,93 +46,93 @@ tlb1_entry: .long 0x0a /* the following data table uses a few of 16 TLB entries */ - .long TLB1_MAS0(1,1,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,1,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #if defined(CFG_FLASH_PORT_WIDTH_16) - .long TLB1_MAS0(1,2,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_4M) - .long TLB1_MAS2(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,3,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_4M) - .long TLB1_MAS2((((CFG_FLASH_BASE+0x400000)>>12)&0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3((((CFG_FLASH_BASE+0x400000)>>12)&0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,2,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_4M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,3,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_4M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE+0x400000,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE+0x400000,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #else - .long TLB1_MAS0(1,2,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16M) - .long TLB1_MAS2(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,3,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,2,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,3,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #endif #if !defined(CONFIG_SPD_EEPROM) - .long TLB1_MAS0(1,4,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) - .long TLB1_MAS2(((CFG_DDR_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,0,0,0) - .long TLB1_MAS3(((CFG_DDR_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,5,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) - .long TLB1_MAS2((((CFG_DDR_SDRAM_BASE+0x4000000)>>12) & 0xfffff),0,0,0,0,0,0,0,0) - .long TLB1_MAS3((((CFG_DDR_SDRAM_BASE+0x4000000)>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,4,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE,0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,5,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE+0x4000000,0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE+0x4000000,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #else - .long TLB1_MAS0(1,4,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,5,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,4,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,5,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #endif - .long TLB1_MAS0(1,6,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS0(1,6,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_64M) #if defined(CONFIG_RAM_AS_FLASH) - .long TLB1_MAS2(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE,(MAS2_I|MAS2_G)) #else - .long TLB1_MAS2(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,0,0,0) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE,0) #endif - .long TLB1_MAS3(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(1,7,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) + .long FSL_BOOKE_MAS0(1,7,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) #ifdef CONFIG_L2_INIT_RAM - .long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,1,0,0,0,0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR,0,0,0,1,0,0,0,0) #else - .long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,0,0,0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR,0) #endif - .long TLB1_MAS3(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR,0,(MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(1,8,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,8,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI_MEM_BASE,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI_MEM_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(1,9,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) - .long TLB1_MAS2(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,9,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) + .long FSL_BOOKE_MAS2(CFG_BCSR,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_BCSR,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR) - .long TLB1_MAS0(1,15,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,15,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #else - .long TLB1_MAS0(1,15,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,15,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/pm854/init.S b/board/pm854/init.S index ade5d6e5b61..0a403abb1b2 100644 --- a/board/pm854/init.S +++ b/board/pm854/init.S @@ -43,7 +43,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -75,10 +75,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -94,33 +94,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -128,69 +120,65 @@ tlb1_entry: * 0xfc000000 64M FLASH (8,16,32 or 64 MB) * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(0xfc000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(0xfc000000), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(0xfc000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(0xfc000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) /* @@ -201,10 +189,10 @@ tlb1_entry: * Likely it needs to be increased by two for these entries. */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/pm856/init.S b/board/pm856/init.S index ade5d6e5b61..0a403abb1b2 100644 --- a/board/pm856/init.S +++ b/board/pm856/init.S @@ -43,7 +43,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -75,10 +75,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -94,33 +94,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -128,69 +120,65 @@ tlb1_entry: * 0xfc000000 64M FLASH (8,16,32 or 64 MB) * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(0xfc000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(0xfc000000), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(0xfc000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(0xfc000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) /* @@ -201,10 +189,10 @@ tlb1_entry: * Likely it needs to be increased by two for these entries. */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/sbc8560/init.S b/board/sbc8560/init.S index 3d8d180d849..95cb85abf77 100644 --- a/board/sbc8560/init.S +++ b/board/sbc8560/init.S @@ -97,69 +97,69 @@ tlb1_entry: /* TLB for CCSRBAR (IMMR) */ - .long TLB1_MAS0(1,1,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,1,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR,0,(MAS3_SX|MAS3_SW|MAS3_SR)) /* TLB for Local Bus stuff, just map the whole 512M */ /* note that the LBC SDRAM is cache-inhibit and guarded, like everything else */ - .long TLB1_MAS0(1,2,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2(((0xe0000000>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((0xe0000000>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,2,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(0xe0000000,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(0xe0000000,0,(MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(1,3,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2(((0xf0000000>>12)&0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((0xf0000000>>12)&0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,3,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(0xf0000000,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(0xf0000000,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) - .long TLB1_MAS0(1,4,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2(((CFG_DDR_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,0,0,0) - .long TLB1_MAS3(((CFG_DDR_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,5,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2((((CFG_DDR_SDRAM_BASE+0x10000000)>>12) & 0xfffff),0,0,0,0,0,0,0,0) - .long TLB1_MAS3((((CFG_DDR_SDRAM_BASE+0x10000000)>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,4,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE,0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,5,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE+0x10000000,0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE+0x10000000,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #else - .long TLB1_MAS0(1,4,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1,5,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,4,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1,5,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #endif - .long TLB1_MAS0(1,6,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) + .long FSL_BOOKE_MAS0(1,6,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_16K) #ifdef CONFIG_L2_INIT_RAM - .long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,1,0,0,0,0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR,0,0,0,1,0,0,0,0) #else - .long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,0,0,0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR,0) #endif - .long TLB1_MAS3(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR,0,(MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(1,7,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) - .long TLB1_MAS2(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,7,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI_MEM_BASE,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI_MEM_BASE,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR) - .long TLB1_MAS0(1,15,0) - .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,1,0,1,0) - .long TLB1_MAS3(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,15,0) + .long FSL_BOOKE_MAS1(1,1,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT,(MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #else - .long TLB1_MAS0(1,15,0) - .long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) - .long TLB1_MAS2(0,0,0,0,0,0,0,0,0) - .long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1,15,0) + .long FSL_BOOKE_MAS1(0,0,0,0,BOOKE_PAGESZ_1M) + .long FSL_BOOKE_MAS2(0,0) + .long FSL_BOOKE_MAS3(0,0,(MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/stxgp3/init.S b/board/stxgp3/init.S index d504289bb20..f491a57cebb 100644 --- a/board/stxgp3/init.S +++ b/board/stxgp3/init.S @@ -49,7 +49,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -81,10 +81,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -100,33 +100,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), \ - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -134,78 +126,74 @@ tlb1_entry: * 0xff000000 16M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), \ - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), \ - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Cacheable, non-guarded * 0xf000_0000 64M LBC SDRAM */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_LBC_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_LBC_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7: 16K Non-cacheable, guarded * 0xfc000000 16K Configuration Latch register */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_LCLDEVS_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_LCLDEVS_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64K) + .long FSL_BOOKE_MAS2(CFG_LBC_LCLDEVS_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_LBC_LCLDEVS_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #if !defined(CONFIG_SPD_EEPROM) /* @@ -217,17 +205,15 @@ tlb1_entry: * Likely it needs to be increased by two for these entries. */ #error("Update the number of table entries in tlb1_entry") - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(1, 9, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE + 0x4000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 8, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(1, 9, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE + 0x4000000, 0) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE + 0x4000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #endif entry_end diff --git a/board/stxssa/init.S b/board/stxssa/init.S index a1a8d9e0cbb..82dafb80b88 100644 --- a/board/stxssa/init.S +++ b/board/stxssa/init.S @@ -49,7 +49,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -81,10 +81,10 @@ tlb1_entry: * This ends up at a TLB0 Index==0 entry, and must not collide * with other TLB0 Entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR_DEFAULT, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR_DEFAULT, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) #else #error("Update the number of table entries in tlb1_entry") #endif @@ -100,33 +100,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), \ - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -134,50 +126,46 @@ tlb1_entry: * 0xfc000000 6M4 FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 1: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), \ - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0xa0000000 256M PCI2 MEM First half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xb0000000 256M PCI2 MEM Second half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), \ - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), \ - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI2_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI2_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 64M Non-cacheable, guarded @@ -185,10 +173,10 @@ tlb1_entry: * 0xe200_0000 16M PCI1 IO * 0xe300_0000 16M PCI2 IO */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 256M Non-cacheable, guarded @@ -196,10 +184,10 @@ tlb1_entry: * 0xfb000000 Configuration Latch register (one word) * 0xfc000000 Up to 64M flash */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_OPTION_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_OPTION_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_LBC_OPTION_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_LBC_OPTION_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) entry_end /* diff --git a/board/tqm85xx/init.S b/board/tqm85xx/init.S index 1f610385e6d..dcb9386c006 100644 --- a/board/tqm85xx/init.S +++ b/board/tqm85xx/init.S @@ -43,7 +43,7 @@ * * MAS0: tlbsel, esel, nv * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS2: epn, x0, x1, w, i, m, g, e * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr */ @@ -78,33 +78,25 @@ tlb1_entry: * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, * and must not collide with other TLB0 entries. */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 4 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 4 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 8 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 8 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + + .long FSL_BOOKE_MAS0(0, 0, 0) + .long FSL_BOOKE_MAS1(1, 0, 0, 0, 0) + .long FSL_BOOKE_MAS2(CFG_INIT_RAM_ADDR + 12 * 1024, 0) + .long FSL_BOOKE_MAS3(CFG_INIT_RAM_ADDR + 12 * 1024, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* @@ -112,64 +104,60 @@ tlb1_entry: * 0xf8000000 128M FLASH * Out of reset this entry is only 4K. */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 1, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + .long FSL_BOOKE_MAS0(1, 0, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_FLASH_BASE+0x4000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_FLASH_BASE+0x4000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 2: 256M Non-cacheable, guarded * 0x80000000 256M PCI1 MEM First half */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 2, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 3: 256M Non-cacheable, guarded * 0x90000000 256M PCI1 MEM Second half */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 3, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_PCI1_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_PCI1_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 4: 256M Non-cacheable, guarded * 0xc0000000 256M Rapid IO MEM First half */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 4, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 5: 256M Non-cacheable, guarded * 0xd0000000 256M Rapid IO MEM Second half */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 5, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_RIO_MEM_BASE + 0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_RIO_MEM_BASE + 0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 6: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR * 0xe200_0000 16M PCI1 IO */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 6, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long FSL_BOOKE_MAS2(CFG_CCSRBAR, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_CCSRBAR, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) /* * TLB 7+8: 512M DDR, cache disabled (needed for memory test) @@ -178,14 +166,14 @@ tlb1_entry: * Make sure the TLB count at the top of this table is correct. * Likely it needs to be increased by two for these entries. */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1) + .long FSL_BOOKE_MAS0(1, 7, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) + .long FSL_BOOKE_MAS0(1, 8, 0) + .long FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long FSL_BOOKE_MAS2(CFG_DDR_SDRAM_BASE+0x10000000, (MAS2_I|MAS2_G)) + .long FSL_BOOKE_MAS3(CFG_DDR_SDRAM_BASE+0x10000000, 0, (MAS3_SX|MAS3_SW|MAS3_SR)) entry_end diff --git a/cpu/mpc85xx/spd_sdram.c b/cpu/mpc85xx/spd_sdram.c index 553f736a56a..adc9c4dd40e 100644 --- a/cpu/mpc85xx/spd_sdram.c +++ b/cpu/mpc85xx/spd_sdram.c @@ -1071,22 +1071,19 @@ setup_laws_and_tlbs(unsigned int memsize) ram_tlb_address = (unsigned int)CFG_DDR_SDRAM_BASE; while (ram_tlb_address < (memsize * 1024 * 1024) && ram_tlb_index < 16) { - mtspr(MAS0, TLB1_MAS0(1, ram_tlb_index, 0)); - mtspr(MAS1, TLB1_MAS1(1, 1, 0, 0, tlb_size)); - mtspr(MAS2, TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), - 0, 0, 0, 0, 0, 0, 0, 0)); - mtspr(MAS3, TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), - 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); + mtspr(MAS0, FSL_BOOKE_MAS0(1, ram_tlb_index, 0)); + mtspr(MAS1, FSL_BOOKE_MAS1(1, 1, 0, 0, tlb_size)); + mtspr(MAS2, FSL_BOOKE_MAS2(ram_tlb_address, 0)); + mtspr(MAS3, FSL_BOOKE_MAS3(ram_tlb_address, 0, + (MAS3_SX|MAS3_SW|MAS3_SR))); asm volatile("isync;msync;tlbwe;isync"); - debug("DDR: MAS0=0x%08x\n", TLB1_MAS0(1, ram_tlb_index, 0)); - debug("DDR: MAS1=0x%08x\n", TLB1_MAS1(1, 1, 0, 0, tlb_size)); - debug("DDR: MAS2=0x%08x\n", - TLB1_MAS2(E500_TLB_EPN(ram_tlb_address), - 0, 0, 0, 0, 0, 0, 0, 0)); + debug("DDR: MAS0=0x%08x\n", FSL_BOOKE_MAS0(1, ram_tlb_index, 0)); + debug("DDR: MAS1=0x%08x\n", FSL_BOOKE_MAS1(1, 1, 0, 0, tlb_size)); + debug("DDR: MAS2=0x%08x\n", FSL_BOOKE_MAS2(ram_tlb_address, 0)); debug("DDR: MAS3=0x%08x\n", - TLB1_MAS3(E500_TLB_RPN(ram_tlb_address), - 0, 0, 0, 0, 0, 1, 0, 1, 0, 1)); + FSL_BOOKE_MAS3(ram_tlb_address, 0, + (MAS3_SX|MAS3_SW|MAS3_SR))); ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2)); ram_tlb_index++; diff --git a/include/asm-ppc/mmu.h b/include/asm-ppc/mmu.h index fed4fd64a72..45a47645edf 100644 --- a/include/asm-ppc/mmu.h +++ b/include/asm-ppc/mmu.h @@ -388,6 +388,19 @@ extern int write_bat(ppc_bat_t bat, unsigned long upper, unsigned long lower); #define MAS7_RPN 0xFFFFFFFF +#define FSL_BOOKE_MAS0(tlbsel,esel,nv) \ + (MAS0_TLBSEL(tlbsel) | MAS0_ESEL(esel) | MAS0_NV(nv)) +#define FSL_BOOKE_MAS1(v,iprot,tid,ts,tsize) \ + ((((v) << 31) & MAS1_VALID) |\ + (((iprot) << 30) & MAS1_IPROT) |\ + (MAS1_TID(tid)) |\ + (((ts) << 12) & MAS1_TS) |\ + (MAS1_TSIZE(tsize))) +#define FSL_BOOKE_MAS2(epn, wimge) \ + (((epn) & MAS3_RPN) | (wimge)) +#define FSL_BOOKE_MAS3(rpn, user, perms) \ + (((rpn) & MAS3_RPN) | (user) | (perms)) + #define BOOKE_PAGESZ_1K 0 #define BOOKE_PAGESZ_4K 1 #define BOOKE_PAGESZ_16K 2 diff --git a/include/e500.h b/include/e500.h index 983826d32cc..1971eee291a 100644 --- a/include/e500.h +++ b/include/e500.h @@ -17,94 +17,6 @@ typedef struct #endif /* _ASMLANGUAGE */ -/* Motorola E500 core provides 16 TLB1 entries; they can be used for - * initial memory mapping like legacy BAT registers do. Usually we - * use four MAS registers(MAS0-3) to operate on TLB1 entries. - * - * While there are 16 Entries with variable Page Sizes in TLB1, - * there are also 256 Entries with fixed 4K pages in TLB0. - * - * We also need LAWs(Local Access Window) to associate a range of - * the local 32-bit address space with a particular target interface - * such as PCI/PCI-X, RapidIO, Local Bus and DDR SDRAM. - * - * We put TLB1/LAW code here because memory mapping is board-specific - * instead of cpu-specific. - * - * While these macros are all nominally for TLB1 by name, they can - * also be used for TLB0 as well. - */ - - -/* - * Convert addresses to Effective and Real Page Numbers. - * Grab the high 20-bits and shift 'em down, dropping the "byte offset". - */ -#define E500_TLB_EPN(addr) (((addr) >> 12) & 0xfffff) -#define E500_TLB_RPN(addr) (((addr) >> 12) & 0xfffff) - - -/* MAS0 - * tlbsel(TLB Select):0,1 - * esel(Entry Select): 0,1,2,...,15 for TLB1 - * nv(Next victim):0,1 - */ -#define TLB1_MAS0(tlbsel,esel,nv) \ - (MAS0_TLBSEL(tlbsel) | MAS0_ESEL(esel) | MAS0_NV(nv)) - -/* MAS1 - * v(TLB valid bit):0,1 - * iprot(invalidate protect):0,1 - * tid(translation identity):8bit to match process IDs - * ts(translation space,comparing with MSR[IS,DS]): 0,1 - * tsize(translation size):1,2,...,9(4K,16K,64K,256K,1M,4M,16M,64M,256M) - */ -#define TLB1_MAS1(v,iprot,tid,ts,tsize) \ - ((((v) << 31) & MAS1_VALID) |\ - (((iprot) << 30) & MAS1_IPROT) |\ - (MAS1_TID(tid)) |\ - (((ts) << 12) & MAS1_TS) |\ - (MAS1_TSIZE(tsize))) - -/* MAS2 - * epn(effective page number):20bits - * sharen(Shared cache state):0,1 - * x0,x1(implementation specific page attribute):0,1 - * w,i,m,g,e(write-through,cache-inhibited,memory coherency,guarded, - * endianness):0,1 - */ -#define TLB1_MAS2(epn,sharen,x0,x1,w,i,m,g,e) \ - ((((epn) << 12) & MAS2_EPN) |\ - (((x0) << 6) & MAS2_X0) |\ - (((x1) << 5) & MAS2_X1) |\ - (((w) << 4) & MAS2_W) |\ - (((i) << 3) & MAS2_I) |\ - (((m) << 2) & MAS2_M) |\ - (((g) << 1) & MAS2_G) |\ - (e) ) - -/* MAS3 - * rpn(real page number):20bits - * u0-u3(user bits, useful for page table management in OS):0,1 - * ux,sx,uw,sw,ur,sr(permission bits, user and supervisor read, - * write,execute permission). - */ -#define TLB1_MAS3(rpn,u0,u1,u2,u3,ux,sx,uw,sw,ur,sr) \ - ((((rpn) << 12) & MAS3_RPN) |\ - (((u0) << 9) & MAS3_U0) |\ - (((u1) << 8) & MAS3_U1) |\ - (((u2) << 7) & MAS3_U2) |\ - (((u3) << 6) & MAS3_U3) |\ - (((ux) << 5) & MAS3_UX) |\ - (((sx) << 4) & MAS3_SX) |\ - (((uw) << 3) & MAS3_UW) |\ - (((sw) << 2) & MAS3_SW) |\ - (((ur) << 1) & MAS3_UR) |\ - (sr) ) - - #define RESET_VECTOR 0xfffffffc -#define CACHELINE_MASK (CFG_CACHELINE_SIZE - 1) /* Address mask for cache - line aligned data. */ #endif /* __E500_H__ */ -- cgit v1.3.1 From 9e3ed392d2c8965e24c942b58796c31c644c2f70 Mon Sep 17 00:00:00 2001 From: Joe Hamman Date: Thu, 13 Dec 2007 06:45:14 -0600 Subject: mpc85xx: Add support for SBC8548 (updated) Add support for Wind River's SBC8548 reference board. Signed-off by: Joe Hamman --- board/sbc8548/u-boot.lds | 149 ++++++++++++ doc/README.sbc8548 | 27 +++ include/configs/sbc8548.h | 576 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 752 insertions(+) create mode 100644 board/sbc8548/u-boot.lds create mode 100644 doc/README.sbc8548 create mode 100644 include/configs/sbc8548.h (limited to 'include') diff --git a/board/sbc8548/u-boot.lds b/board/sbc8548/u-boot.lds new file mode 100644 index 00000000000..4cd177e4843 --- /dev/null +++ b/board/sbc8548/u-boot.lds @@ -0,0 +1,149 @@ +/* + * Copyright 2004, 2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/sbc8548/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/sbc8548/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + drivers/net/tsec.o (.text) + cpu/mpc85xx/speed.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/doc/README.sbc8548 b/doc/README.sbc8548 new file mode 100644 index 00000000000..b34d0406cbb --- /dev/null +++ b/doc/README.sbc8548 @@ -0,0 +1,27 @@ +Wind River SBC8548 reference board +=========================== + +Copyright 2007, Embedded Specialties, Inc. +Copyright 2007 Wind River Systemes, Inc. +----------------------------- + +1. Building U-Boot +------------------ +The SBC8548 code is known to build using ELDK 4.1. + + $ make sbc8548_config + Configuring for sbc8548 board... + + $ make + + +2. Switch and Jumper Settings +----------------------------- +All Jumpers & Switches are in their default positions. Please refer to +the board documentation for details. Some settings control CPU voltages +and settings may change with board revisions. + +3. Known limitations +-------------------- +PCI: + The code to support PCI is currently disabled and has not been verified. diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h new file mode 100644 index 00000000000..30d7b011155 --- /dev/null +++ b/include/configs/sbc8548.h @@ -0,0 +1,576 @@ +/* + * Copyright 2007 Wind River Systems + * Copyright 2007 Embedded Specialties, Inc. + * Copyright 2004, 2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * sbc8548 board configuration file + * + * Please refer to doc/README.sbc85xx for more info. + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 /* MPC8548 specific */ +#define CONFIG_SBC8548 1 /* SBC8548 board specific */ + +#undef CONFIG_PCI /* enable any pci type devices */ +#undef CONFIG_PCI1 /* PCI controller 1 */ +#undef CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#undef CONFIG_RIO +#undef CONFIG_PCI2 +#undef CONFIG_FSL_PCI_INIT /* Use common FSL init code */ + +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + + +#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ + +#define CONFIG_SYS_CLK_FREQ 66000000 /* SBC8548 default SYSCLK */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00400000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) +#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +/* + * Make sure required options are set + */ +#ifndef CONFIG_SPD_EEPROM + #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */ +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * FLASH on the Local Bus + * Two banks, one 8MB the other 64MB, using the CFI driver. + * Boot from BR0/OR0 bank at 0xff80_0000 + * Alternate BR6/OR6 bank at 0xfb80_0000 + * + * BR0: + * Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0 + * Port Size = 8 bits = BRx[19:20] = 01 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0 + * + * BR6: + * Base address 6 = 0xfb80_0000 = BR6[0:16] = 1111 1011 1000 0000 0 + * Port Size = 32 bits = BRx[19:20] = 11 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1011 1000 0000 0001 1000 0000 0001 = fb801801 BR6 + * + * OR0: + * Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0 + * XAM = OR0[17:18] = 11 + * CSNT = OR0[20] = 1 + * ACS = half cycle delay = OR0[21:22] = 11 + * SCY = 6 = OR0[24:27] = 0110 + * TRLX = use relaxed timing = OR0[29] = 1 + * EAD = use external address latch delay = OR0[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0 + * + * OR6: + * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0 + * XAM = OR6[17:18] = 11 + * CSNT = OR6[20] = 1 + * ACS = half cycle delay = OR6[21:22] = 11 + * SCY = 6 = OR6[24:27] = 0110 + * TRLX = use relaxed timing = OR6[29] = 1 + * EAD = use external address latch delay = OR6[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6 + */ + +#define CFG_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */ +#define CFG_FLASH_BASE CFG_BOOT_BLOCK /* start of FLASH 16M */ + +#define CFG_BR0_PRELIM 0xff800801 +#define CFG_BR6_PRELIM 0xfb801801 + +#define CFG_OR0_PRELIM 0xff806e65 +#define CFG_OR6_PRELIM 0xfc006e65 + +#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + +/* CS5 = Local bus peripherals controlled by the EPLD */ + +#define CFG_BR5_PRELIM 0xf8000801 +#define CFG_OR5_PRELIM 0xff006e65 +#define CFG_EPLD_BASE 0xf8000000 +#define CFG_LED_DISP_BASE 0xf8000000 +#define CFG_USER_SWITCHES_BASE 0xf8100000 +#define CFG_BD_REV 0xf8300000 +#define CFG_EEPROM_BASE 0xf8b00000 + +/* + * SDRAM on the Local Bus + */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* + * Base Register 3 and Option Register 3 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR3, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port-size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 + * + */ + +#define CFG_BR3_PRELIM 0xf0001861 + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR3, need: + * 64MB mask for AM, OR3[0:7] = 1111 1100 + * XAM, OR3[17:18] = 11 + * 10 columns OR3[19-21] = 011 + * 12 rows OR3[23-25] = 011 + * EAD set for extra time OR[31] = 0 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0 + */ + +#define CFG_OR3_PRELIM 0xfc006cc0 + +#define CFG_LBC_LCRR 0x00000002 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) +#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) +#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) +#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) +#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) +#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) +#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) +#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) +#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) +#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) + +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +/* + * Common settings for all Local Bus SDRAM commands. + * At run time, either BSMA1516 (for CPU 1.1) + * or BSMA1617 (for CPU 1.0) (old) + * is OR'ed in too. + */ +#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \ + | CFG_LBC_LSDMR_PRETOACT7 \ + | CFG_LBC_LSDMR_ACTTORW7 \ + | CFG_LBC_LSDMR_BL8 \ + | CFG_LBC_LSDMR_WRC4 \ + | CFG_LBC_LSDMR_CL3 \ + | CFG_LBC_LSDMR_RFEN \ + ) + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK 400000000 /* get_bus_freq(0) */ + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_OFFSET 0x3000 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */ + +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe2000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#ifdef CONFIG_PCI2 +#define CFG_PCI2_MEM_BASE 0xa0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0x00000000 +#define CFG_PCI2_IO_PHYS 0xe2800000 +#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */ +#endif + +#ifdef CONFIG_PCIE1 +#define CFG_PCIE1_MEM_BASE 0xa0000000 +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0x00000000 +#define CFG_PCIE1_IO_PHYS 0xe3000000 +#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ +#endif + +#ifdef CONFIG_RIO +/* + * RapidIO MMU + */ +#define CFG_RIO_MEM_BASE 0xC0000000 +#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */ +#endif + +#ifdef CONFIG_LEGACY +#define BRIDGE_ID 17 +#define VIA_ID 2 +#else +#define BRIDGE_ID 28 +#define VIA_ID 4 +#endif + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +#endif /* CONFIG_PCI */ + + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC2" +#define CONFIG_TSEC4 +#define CONFIG_TSEC4_NAME "eTSEC3" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC3_PHY_ADDR 2 +#define TSEC4_PHY_ADDR 3 + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) + +/* Options are: eTSEC[0-3] */ +#define CONFIG_ETHPRIME "eTSEC0" +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ +#define CFG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 02:E0:0C:00:00:FD +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD +#define CONFIG_HAS_ETH3 +#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD +#endif + +#define CONFIG_IPADDR 192.168.0.55 + +#define CONFIG_HOSTNAME sbc8548 +#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx +#define CONFIG_BOOTFILE /uImage +#define CONFIG_UBOOTPATH /u-boot.bin /* TFTP server */ + +#define CONFIG_SERVERIP 192.168.0.2 +#define CONFIG_GATEWAYIP 192.168.0.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ + "tftpflash=tftpboot $loadaddr $uboot; " \ + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \ + "erase " MK_STR(TEXT_BASE) " +$filesize; " \ + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \ + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \ + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=uRamdisk\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=sbc8548.dtb\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 7bd6104b71de9bca80ac8e0936003443bb42f2fc Mon Sep 17 00:00:00 2001 From: robert lazarski Date: Fri, 21 Dec 2007 10:36:37 -0500 Subject: mpc85xx: Add support for ATUM8548 (updated) Add support for Instituto Atlantico's ATUM8548 board Signed-off-by: robert lazarski --- MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + board/atum8548/u-boot.lds | 147 ++++++++++++++ doc/README.atum8548 | 29 +++ include/configs/ATUM8548.h | 465 +++++++++++++++++++++++++++++++++++++++++++++ 6 files changed, 649 insertions(+) create mode 100644 board/atum8548/u-boot.lds create mode 100644 doc/README.atum8548 create mode 100644 include/configs/ATUM8548.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 88a38caf59a..2ef2f5c7c49 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -222,6 +222,10 @@ Thomas Lange GTH MPC860 +Robert Lazarski + + ATUM8548 MPC8548 + The LEOX team ELPT860 MPC860T diff --git a/MAKEALL b/MAKEALL index 73ba7a28522..ebc5a225abd 100755 --- a/MAKEALL +++ b/MAKEALL @@ -324,6 +324,7 @@ LIST_83xx=" \ ######################################################################### LIST_85xx=" \ + ATUM8548 \ MPC8540ADS \ MPC8540EVAL \ MPC8541CDS \ diff --git a/Makefile b/Makefile index d3608fd93b4..2f3d72a9c32 100644 --- a/Makefile +++ b/Makefile @@ -1943,6 +1943,9 @@ TQM834x_config: unconfig ## MPC85xx Systems ######################################################################### +ATUM8548_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc85xx atum8548 + MPC8540ADS_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc85xx mpc8540ads freescale diff --git a/board/atum8548/u-boot.lds b/board/atum8548/u-boot.lds new file mode 100644 index 00000000000..5c0e8a2d734 --- /dev/null +++ b/board/atum8548/u-boot.lds @@ -0,0 +1,147 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/atum8548/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/atum8548/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/speed.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/doc/README.atum8548 b/doc/README.atum8548 new file mode 100644 index 00000000000..4eb56bae2fc --- /dev/null +++ b/doc/README.atum8548 @@ -0,0 +1,29 @@ +Building U-Boot +--------------- + +The ATUM8548 code is known to build using ELDK 4.1. + +$ make ATUM8548_config +Configuring for ATUM8548 board... +$ make + +Using Flash +----------- + +The ATUM8548 board has one flash bank, of 128MB in size (2^23 = 0x08000000). + +The BDI2000 commands for copying u-boot into flash are +as follows: + + erase 0xFFF80000 0x4000 0x20 + prog 0xfff80000 uboot.bin bin + +Booting Linux +------------- + +U-boot/kermit commands for booting linux via NFS - assumming the proper +bootargs are set - are as follows: + + tftp 1000000 uImage.atum + tftp c00000 mpc8548atum.dtb + bootm 1000000 - c00000 diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h new file mode 100644 index 00000000000..e11a4454362 --- /dev/null +++ b/include/configs/ATUM8548.h @@ -0,0 +1,465 @@ +/* + * Copyright 2007 + * Robert Lazarski, Instituto Atlantico, robertlazarski@gmail.com + * + * Copyright 2004, 2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * atum8548 board configuration file + * + * Please refer to doc/README.atum8548 for more info. + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* Debug Options, Disable in production +#define ET_DEBUG 1 +#define CONFIG_PANIC_HANG 1 +#define DEBUG 1 +*/ + +/* CPLD Configuration Options */ +#define MPC85xx_ATUM_CLKOCR 0x80000002 + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 /* MPC8548 specific */ + +#define CONFIG_PCI 1 /* enable any pci type devices */ +#define CONFIG_PCI1 1 /* PCI controller 1 */ +#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCI2 1 /* PCI controller 2 */ +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ + +#define CONFIG_TSEC_ENET 1 /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for DDR setup*/ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef +#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ + +#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ + +#define CONFIG_SYS_CLK_FREQ 33000000 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#define CONFIG_CMD_SDRAM 1 /* SDRAM DIMM SPD info printout */ +#define CONFIG_ENABLE_36BIT_PHYS 1 +#undef CFG_DRAM_TEST +#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00400000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +#define PCI_SPEED 33333000 /* CPLD currenlty does not have PCI setup info */ +#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) +#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000) + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#if defined(CONFIG_SPD_EEPROM) + /* + * Determine DDR configuration from I2C interface. + */ + #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +#else + /* + * Manually set up DDR parameters + */ + #define CFG_SDRAM_SIZE 1024 /* DDR is 1024MB */ + #define CFG_DDR_CS0_BNDS 0x0000000f /* 0-1024 */ + #define CFG_DDR_CS0_CONFIG 0x80000102 + #define CFG_DDR_TIMING_0 0x00260802 + #define CFG_DDR_TIMING_1 0x38355322 + #define CFG_DDR_TIMING_2 0x039048c7 + #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ + #define CFG_DDR_MODE 0x00000432 + #define CFG_DDR_INTERVAL 0x05150100 + #define DDR_SDRAM_CFG 0x43000000 +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Local Bus Definitions + */ + +/* + * FLASH on the Local Bus + * based on flash chip S29GL01GP + * One bank, 128M, using the CFI driver. + * Boot from BR0 bank at 0xf800_0000 + * + * BR0: + * Base address 0 = 0xF8000000 = BR0[0:16] = 1111 1000 0000 0000 0 + * Port Size = 16 bits = BRx[19:20] = 10 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1000 0000 0000 0001 0000 0000 0001 = f8001001 BR0 + * + * OR0: + * Addr Mask = 128M = ORx[0:16] = 1111 1000 0000 0000 0 + * Reserved ORx[17:18] = 00 + * CSNT = ORx[20] = 1 + * ACS = half cycle delay = ORx[21:22] = 11 + * SCY = 6 = ORx[24:27] = 0110 + * TRLX = use relaxed timing = ORx[29] = 1 + * EAD = use external address latch delay = OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1000 0000 0000 0000 1110 0110 0101 = f8000E65 ORx + */ + +#define CFG_BOOT_BLOCK 0xf8000000 /* boot TLB block */ +#define CFG_FLASH_BASE CFG_BOOT_BLOCK /* start of FLASH 128M */ + +#define CFG_BR0_PRELIM 0xf8001001 + +#define CFG_OR0_PRELIM 0xf8000E65 + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 512000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 8000 /* Flash Write Timeout (ms) */ + + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER 1 +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_EMPTY_INFO + +/* + * Flash on the LocalBus + */ +#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ + +/* Memory */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ +#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */ + +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xe2000000 +#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ + +#ifdef CONFIG_PCI2 +#define CFG_PCI2_MEM_BASE 0xC0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0x00000000 +#define CFG_PCI2_IO_PHYS 0xe2800000 +#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */ +#endif + +#ifdef CONFIG_PCIE1 +#define CFG_PCIE1_MEM_BASE 0xa0000000 +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0x00000000 +#define CFG_PCIE1_IO_PHYS 0xe3000000 +#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */ +#endif + + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ +#endif + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "eTSEC2" +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "eTSEC3" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC3_PHY_ADDR 2 +#define TSEC4_PHY_ADDR 3 + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT +#define TSEC3_FLAGS TSEC_GIGABIT +#define TSEC4_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-3] */ +#define CONFIG_ETHPRIME "eTSEC2" +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ +#define CFG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_ETHADDR 00:E0:0C:00:00:FD +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD +#define CONFIG_HAS_ETH3 +#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD +#endif + +#define CONFIG_IPADDR 10.101.43.142 + +#define CONFIG_HOSTNAME atum +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE /tftpboot/uImage.atum +#define CONFIG_UBOOTPATH /tftpboot/uboot.bin /* TFTP server */ + +#define CONFIG_SERVERIP 10.101.43.10 +#define CONFIG_GATEWAYIP 10.101.45.1 +#define CONFIG_NETMASK 255.255.248.0 + +#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $dtbaddr $dtbfile;" \ + "bootm $loadaddr - $dtbaddr" + + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $dtbaddr $dtbfile;" \ + "bootm $loadaddr $ramdiskaddr $dtbaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From b009f3eca99bb7b9e6ba6639a8909a138dd5e9fe Mon Sep 17 00:00:00 2001 From: Kumar Gala Date: Tue, 8 Jan 2008 01:22:21 -0600 Subject: 85xx: Remove cache config from configs.h Either use the standard defines in asm/cache.h or grab the information at runtime from the L1CFG SPR. Also, minor cleanup in cache.h to make the code a bit more readable. Signed-off-by: Kumar Gala --- cpu/mpc85xx/start.S | 9 +++++++-- include/asm-ppc/cache.h | 10 ++++------ include/asm-ppc/processor.h | 4 ++++ include/configs/MPC8540ADS.h | 7 ------- include/configs/MPC8540EVAL.h | 7 ------- include/configs/MPC8541CDS.h | 7 ------- include/configs/MPC8544DS.h | 7 ------- include/configs/MPC8548CDS.h | 7 ------- include/configs/MPC8555CDS.h | 7 ------- include/configs/MPC8560ADS.h | 7 ------- include/configs/MPC8568MDS.h | 7 ------- include/configs/MPC8641HPCN.h | 7 ------- include/configs/PM854.h | 7 ------- include/configs/PM856.h | 7 ------- include/configs/SBC8540.h | 7 ------- include/configs/TQM85xx.h | 7 ------- include/configs/sbc8560.h | 7 ------- include/configs/stxgp3.h | 7 ------- include/configs/stxssa.h | 7 ------- 19 files changed, 15 insertions(+), 120 deletions(-) (limited to 'include') diff --git a/cpu/mpc85xx/start.S b/cpu/mpc85xx/start.S index b769ef8a76a..b489d2ff0ca 100644 --- a/cpu/mpc85xx/start.S +++ b/cpu/mpc85xx/start.S @@ -268,7 +268,10 @@ _start_e500: */ lis r3,CFG_INIT_RAM_ADDR@h ori r3,r3,CFG_INIT_RAM_ADDR@l - li r2,(CFG_DCACHE_SIZE / (2 * CFG_CACHELINE_SIZE)) + mfspr r2, L1CFG0 + andi. r2, r2, 0x1ff + /* cache size * 1024 / (2 * L1 line size) */ + slwi r2, r2, (10 - 1 - L1_CACHE_SHIFT) mtctr r2 li r0,0 1: @@ -1061,7 +1064,9 @@ unlock_ram_in_cache: /* invalidate the INIT_RAM section */ lis r3,(CFG_INIT_RAM_ADDR & ~31)@h ori r3,r3,(CFG_INIT_RAM_ADDR & ~31)@l - li r4,(CFG_DCACHE_SIZE / (2 * CFG_CACHELINE_SIZE)) + mfspr r4,L1CFG0 + andi. r4,r4,0x1ff + slwi r4,r4,(10 - 1 - L1_CACHE_SHIFT) mtctr r4 1: icbi r0,r3 dcbi r0,r3 diff --git a/include/asm-ppc/cache.h b/include/asm-ppc/cache.h index e29bfc2a7b4..9d9b9717dde 100644 --- a/include/asm-ppc/cache.h +++ b/include/asm-ppc/cache.h @@ -8,15 +8,13 @@ #include /* bytes per L1 cache line */ -#if !(defined(CONFIG_8xx) || defined(CONFIG_IOP480)) -#if defined(CONFIG_PPC64BRIDGE) +#if defined(CONFIG_8xx) || defined(CONFIG_IOP480) +#define L1_CACHE_SHIFT 4 +#elif defined(CONFIG_PPC64BRIDGE) #define L1_CACHE_SHIFT 7 #else #define L1_CACHE_SHIFT 5 -#endif /* PPC64 */ -#else -#define L1_CACHE_SHIFT 4 -#endif /* !(8xx || IOP480) */ +#endif #define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT) diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 9fbbdf8c56a..86c5df2dbaa 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -424,6 +424,8 @@ #define SPRN_IVOR15 0x19f /* Interrupt Vector Offset Register 15 */ /* e500 definitions */ +#define SPRN_L1CFG0 0x203 /* L1 Cache Configuration Register 0 */ +#define SPRN_L1CFG1 0x204 /* L1 Cache Configuration Register 1 */ #define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */ #define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */ #define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */ @@ -621,6 +623,8 @@ #define MCSRR1 SPRN_MCSRR1 #define L1CSR0 SPRN_L1CSR0 #define L1CSR1 SPRN_L1CSR1 +#define L1CFG0 SPRN_L1CFG0 +#define L1CFG1 SPRN_L1CFG1 #define MCSR SPRN_MCSR #define MMUCSR0 SPRN_MMUCSR0 #define BUCSR SPRN_BUCSR diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 35e1d630666..afce7fb78fe 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -460,13 +460,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h index e376c11656b..2868dcb8ad6 100644 --- a/include/configs/MPC8540EVAL.h +++ b/include/configs/MPC8540EVAL.h @@ -319,13 +319,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index d2e7237895e..c83382f0df6 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -450,13 +450,6 @@ extern unsigned long get_clock_freq(void); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 545a76cc621..5a96db5ab25 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -444,13 +444,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 3f382e59a6b..90beb252138 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -512,13 +512,6 @@ extern unsigned long get_clock_freq(void); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 90ef3d6b673..76d673cd0d6 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -450,13 +450,6 @@ extern unsigned long get_clock_freq(void); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index d4e0de0d32b..5f105552f40 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -490,13 +490,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 59f490e8566..2b089d90d68 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -480,13 +480,6 @@ extern unsigned long get_clock_freq(void); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 575bbae431f..7f485c68f6c 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -573,13 +573,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) - #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/PM854.h b/include/configs/PM854.h index a6a1e738a80..f0d0399a9d0 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -366,13 +366,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/PM856.h b/include/configs/PM856.h index 9a17e3d7333..ae2645c079c 100644 --- a/include/configs/PM856.h +++ b/include/configs/PM856.h @@ -365,13 +365,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index f2c3699ab74..3ca85b8a9fe 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -395,13 +395,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) - #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index 6dbd3924bdd..f3b1a53fe9c 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -417,13 +417,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index defc428819b..b71ba785be8 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -377,13 +377,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) - #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index c5ae0cde361..3baa32c8d6e 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -357,13 +357,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index c6e79532096..9457bce0aea 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -391,13 +391,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - /* * Internal Definitions * -- cgit v1.3.1 From b8ec2385038c094b07ec5b49336289a46b6e9cc6 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Mon, 7 Jan 2008 13:31:19 -0600 Subject: 85xx: add ability to upload QE firmware Define the layout of a binary blob that contains a QE firmware and instructions on how to upload it. Add function qe_upload_firmware() to parse the blob and perform the actual upload. Add command-line command "qe fw" to take a firmware blob in memory and upload it. Update ft_cpu_setup() on 85xx to create the 'firmware' device tree node if U-Boot has uploaded a firmware. Fully define 'struct rsp' in immap_qe.h to include the actual RISC Special Registers. Signed-off-by: Timur Tabi --- common/fdt_support.c | 48 ++++++++++ cpu/mpc85xx/fdt.c | 1 + drivers/qe/qe.c | 219 +++++++++++++++++++++++++++++++++++++++++++++ drivers/qe/qe.h | 56 ++++++++++++ include/asm-ppc/immap_qe.h | 33 ++++++- include/fdt_support.h | 1 + 6 files changed, 356 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/common/fdt_support.c b/common/fdt_support.c index 92f1c7f54fd..a13c140cff4 100644 --- a/common/fdt_support.c +++ b/common/fdt_support.c @@ -30,6 +30,9 @@ #include #include +#ifdef CONFIG_QE +#include "../drivers/qe/qe.h" +#endif /* * Global data (for the gd->bd) */ @@ -614,4 +617,49 @@ void fdt_fixup_ethernet(void *fdt, bd_t *bd) #endif } } + +#ifdef CONFIG_QE +/* + * If a QE firmware has been uploaded, then add the 'firmware' node under + * the 'qe' node. + */ +void fdt_fixup_qe_firmware(void *fdt) +{ + struct qe_firmware_info *qe_fw_info; + int node, ret; + + qe_fw_info = qe_get_firmware_info(); + if (!qe_fw_info) + return; + + node = fdt_path_offset(fdt, "/qe"); + if (node < 0) + return; + + /* We assume the node doesn't exist yet */ + node = fdt_add_subnode(fdt, node, "firmware"); + if (node < 0) + return; + + ret = fdt_setprop(fdt, node, "extended-modes", + &qe_fw_info->extended_modes, sizeof(u64)); + if (ret < 0) + goto error; + + ret = fdt_setprop_string(fdt, node, "id", qe_fw_info->id); + if (ret < 0) + goto error; + + ret = fdt_setprop(fdt, node, "virtual-traps", qe_fw_info->vtraps, + sizeof(qe_fw_info->vtraps)); + if (ret < 0) + goto error; + + return; + +error: + fdt_del_node(fdt, node); +} +#endif + #endif diff --git a/cpu/mpc85xx/fdt.c b/cpu/mpc85xx/fdt.c index 737a6c485a2..0812c89a2e5 100644 --- a/cpu/mpc85xx/fdt.c +++ b/cpu/mpc85xx/fdt.c @@ -45,6 +45,7 @@ void ft_cpu_setup(void *blob, bd_t *bd) #ifdef CONFIG_QE do_fixup_by_prop_u32(blob, "device_type", "soc", 4, "bus-frequency", bd->bi_busfreq, 1); + fdt_fixup_qe_firmware(blob); #endif #ifdef CFG_NS16550 diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c index 7559e922272..276788c8574 100644 --- a/drivers/qe/qe.c +++ b/drivers/qe/qe.c @@ -21,6 +21,7 @@ */ #include "common.h" +#include #include "asm/errno.h" #include "asm/io.h" #include "asm/immap_qe.h" @@ -248,4 +249,222 @@ int qe_set_mii_clk_src(int ucc_num) return 0; } +/* The maximum number of RISCs we support */ +#define MAX_QE_RISC 2 + +/* Firmware information stored here for qe_get_firmware_info() */ +static struct qe_firmware_info qe_firmware_info; + +/* + * Set to 1 if QE firmware has been uploaded, and therefore + * qe_firmware_info contains valid data. + */ +static int qe_firmware_uploaded; + +/* + * Upload a QE microcode + * + * This function is a worker function for qe_upload_firmware(). It does + * the actual uploading of the microcode. + */ +static void qe_upload_microcode(const void *base, + const struct qe_microcode *ucode) +{ + const u32 *code = base + be32_to_cpu(ucode->code_offset); + unsigned int i; + + if (ucode->major || ucode->minor || ucode->revision) + printf("QE: uploading microcode '%s' version %u.%u.%u\n", + ucode->id, ucode->major, ucode->minor, ucode->revision); + else + printf("QE: uploading microcode '%s'\n", ucode->id); + + /* Use auto-increment */ + out_be32(&qe_immr->iram.iadd, be32_to_cpu(ucode->iram_offset) | + QE_IRAM_IADD_AIE | QE_IRAM_IADD_BADDR); + + for (i = 0; i < be32_to_cpu(ucode->count); i++) + out_be32(&qe_immr->iram.idata, be32_to_cpu(code[i])); +} + +/* + * Upload a microcode to the I-RAM at a specific address. + * + * See docs/README.qe_firmware for information on QE microcode uploading. + * + * Currently, only version 1 is supported, so the 'version' field must be + * set to 1. + * + * The SOC model and revision are not validated, they are only displayed for + * informational purposes. + * + * 'calc_size' is the calculated size, in bytes, of the firmware structure and + * all of the microcode structures, minus the CRC. + * + * 'length' is the size that the structure says it is, including the CRC. + */ +int qe_upload_firmware(const struct qe_firmware *firmware) +{ + unsigned int i; + unsigned int j; + u32 crc; + size_t calc_size = sizeof(struct qe_firmware); + size_t length; + const struct qe_header *hdr; + + if (!firmware) { + printf("Invalid address\n"); + return -EINVAL; + } + + hdr = &firmware->header; + length = be32_to_cpu(hdr->length); + + /* Check the magic */ + if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') || + (hdr->magic[2] != 'F')) { + printf("Not a microcode\n"); + return -EPERM; + } + + /* Check the version */ + if (hdr->version != 1) { + printf("Unsupported version\n"); + return -EPERM; + } + + /* Validate some of the fields */ + if ((firmware->count < 1) || (firmware->count >= MAX_QE_RISC)) { + printf("Invalid data\n"); + return -EINVAL; + } + + /* Validate the length and check if there's a CRC */ + calc_size += (firmware->count - 1) * sizeof(struct qe_microcode); + + for (i = 0; i < firmware->count; i++) + /* + * For situations where the second RISC uses the same microcode + * as the first, the 'code_offset' and 'count' fields will be + * zero, so it's okay to add those. + */ + calc_size += sizeof(u32) * + be32_to_cpu(firmware->microcode[i].count); + + /* Validate the length */ + if (length != calc_size + sizeof(u32)) { + printf("Invalid length\n"); + return -EPERM; + } + + /* + * Validate the CRC. We would normally call crc32_no_comp(), but that + * function isn't available unless you turn on JFFS support. + */ + crc = be32_to_cpu(*(u32 *)((void *)firmware + calc_size)); + if (crc != (crc32(-1, (const void *) firmware, calc_size) ^ -1)) { + printf("Firmware CRC is invalid\n"); + return -EIO; + } + + /* + * If the microcode calls for it, split the I-RAM. + */ + if (!firmware->split) { + out_be16(&qe_immr->cp.cercr, + in_be16(&qe_immr->cp.cercr) | QE_CP_CERCR_CIR); + } + + if (firmware->soc.model) + printf("Firmware '%s' for %u V%u.%u\n", + firmware->id, be16_to_cpu(firmware->soc.model), + firmware->soc.major, firmware->soc.minor); + else + printf("Firmware '%s'\n", firmware->id); + + /* + * The QE only supports one microcode per RISC, so clear out all the + * saved microcode information and put in the new. + */ + memset(&qe_firmware_info, 0, sizeof(qe_firmware_info)); + strcpy(qe_firmware_info.id, firmware->id); + qe_firmware_info.extended_modes = firmware->extended_modes; + memcpy(qe_firmware_info.vtraps, firmware->vtraps, + sizeof(firmware->vtraps)); + qe_firmware_uploaded = 1; + + /* Loop through each microcode. */ + for (i = 0; i < firmware->count; i++) { + const struct qe_microcode *ucode = &firmware->microcode[i]; + + /* Upload a microcode if it's present */ + if (ucode->code_offset) + qe_upload_microcode(firmware, ucode); + + /* Program the traps for this processor */ + for (j = 0; j < 16; j++) { + u32 trap = be32_to_cpu(ucode->traps[j]); + + if (trap) + out_be32(&qe_immr->rsp[i].tibcr[j], trap); + } + + /* Enable traps */ + out_be32(&qe_immr->rsp[i].eccr, be32_to_cpu(ucode->eccr)); + } + + return 0; +} + +struct qe_firmware_info *qe_get_firmware_info(void) +{ + return qe_firmware_uploaded ? &qe_firmware_info : NULL; +} + +static int qe_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + ulong addr; + + if (argc < 3) { + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; + } + + if (strcmp(argv[1], "fw") == 0) { + addr = simple_strtoul(argv[2], NULL, 16); + + if (!addr) { + printf("Invalid address\n"); + return -EINVAL; + } + + /* + * If a length was supplied, compare that with the 'length' + * field. + */ + + if (argc > 3) { + ulong length = simple_strtoul(argv[3], NULL, 16); + struct qe_firmware *firmware = (void *) addr; + + if (length != be32_to_cpu(firmware->header.length)) { + printf("Length mismatch\n"); + return -EINVAL; + } + } + + return qe_upload_firmware((const struct qe_firmware *) addr); + } + + printf ("Usage:\n%s\n", cmdtp->usage); + return 1; +} + +U_BOOT_CMD( + qe, 4, 0, qe_cmd, + "qe - QUICC Engine commands\n", + "fw [] - Upload firmware binary at address to " + "the QE,\n\twith optional length verification.\n" + ); + #endif /* CONFIG_QE */ diff --git a/drivers/qe/qe.h b/drivers/qe/qe.h index 400b1a6f603..4c96c67ff34 100644 --- a/drivers/qe/qe.h +++ b/drivers/qe/qe.h @@ -222,6 +222,60 @@ typedef enum qe_clock { #define QE_SDEBCR_BA_MASK 0x01FFFFFF +/* Communication Processor */ +#define QE_CP_CERCR_MEE 0x8000 /* Multi-user RAM ECC enable */ +#define QE_CP_CERCR_IEE 0x4000 /* Instruction RAM ECC enable */ +#define QE_CP_CERCR_CIR 0x0800 /* Common instruction RAM */ + +/* I-RAM */ +#define QE_IRAM_IADD_AIE 0x80000000 /* Auto Increment Enable */ +#define QE_IRAM_IADD_BADDR 0x00080000 /* Base Address */ + +/* Structure that defines QE firmware binary files. + * + * See doc/README.qe_firmware for a description of these fields. + */ +struct qe_firmware { + struct qe_header { + u32 length; /* Length of the entire structure, in bytes */ + u8 magic[3]; /* Set to { 'Q', 'E', 'F' } */ + u8 version; /* Version of this layout. First ver is '1' */ + } header; + u8 id[62]; /* Null-terminated identifier string */ + u8 split; /* 0 = shared I-RAM, 1 = split I-RAM */ + u8 count; /* Number of microcode[] structures */ + struct { + u16 model; /* The SOC model */ + u8 major; /* The SOC revision major */ + u8 minor; /* The SOC revision minor */ + } __attribute__ ((packed)) soc; + u8 padding[4]; /* Reserved, for alignment */ + u64 extended_modes; /* Extended modes */ + u32 vtraps[8]; /* Virtual trap addresses */ + u8 reserved[4]; /* Reserved, for future expansion */ + struct qe_microcode { + u8 id[32]; /* Null-terminated identifier */ + u32 traps[16]; /* Trap addresses, 0 == ignore */ + u32 eccr; /* The value for the ECCR register */ + u32 iram_offset; /* Offset into I-RAM for the code */ + u32 count; /* Number of 32-bit words of the code */ + u32 code_offset; /* Offset of the actual microcode */ + u8 major; /* The microcode version major */ + u8 minor; /* The microcode version minor */ + u8 revision; /* The microcode version revision */ + u8 padding; /* Reserved, for alignment */ + u8 reserved[4]; /* Reserved, for future expansion */ + } __attribute__ ((packed)) microcode[1]; + /* All microcode binaries should be located here */ + /* CRC32 should be located here, after the microcode binaries */ +} __attribute__ ((packed)); + +struct qe_firmware_info { + char id[64]; /* Firmware name */ + u32 vtraps[8]; /* Virtual trap addresses */ + u64 extended_modes; /* Extended modes */ +}; + void qe_config_iopin(u8 port, u8 pin, int dir, int open_drain, int assign); void qe_issue_cmd(uint cmd, uint sbc, u8 mcn, u32 cmd_data); uint qe_muram_alloc(uint size, uint align); @@ -233,5 +287,7 @@ void qe_reset(void); void qe_assign_page(uint snum, uint para_ram_base); int qe_set_brg(uint brg, uint rate); int qe_set_mii_clk_src(int ucc_num); +int qe_upload_firmware(const struct qe_firmware *firmware); +struct qe_firmware_info *qe_get_firmware_info(void); #endif /* __QE_H__ */ diff --git a/include/asm-ppc/immap_qe.h b/include/asm-ppc/immap_qe.h index a16a6d3fc5f..39da3771c95 100644 --- a/include/asm-ppc/immap_qe.h +++ b/include/asm-ppc/immap_qe.h @@ -513,10 +513,39 @@ typedef struct dbg { u8 res2[0x48]; } __attribute__ ((packed)) dbg_t; -/* RISC Special Registers (Trap and Breakpoint) +/* + * RISC Special Registers (Trap and Breakpoint). These are described in + * the QE Developer's Handbook. */ typedef struct rsp { - u8 fixme[0x100]; + u32 tibcr[16]; /* Trap/instruction breakpoint control regs */ + u8 res0[64]; + u32 ibcr0; + u32 ibs0; + u32 ibcnr0; + u8 res1[4]; + u32 ibcr1; + u32 ibs1; + u32 ibcnr1; + u32 npcr; + u32 dbcr; + u32 dbar; + u32 dbamr; + u32 dbsr; + u32 dbcnr; + u8 res2[12]; + u32 dbdr_h; + u32 dbdr_l; + u32 dbdmr_h; + u32 dbdmr_l; + u32 bsr; + u32 bor; + u32 bior; + u8 res3[4]; + u32 iatr[4]; + u32 eccr; /* Exception control configuration register */ + u32 eicr; + u8 res4[0x100-0xf8]; } __attribute__ ((packed)) rsp_t; typedef struct qe_immap { diff --git a/include/fdt_support.h b/include/fdt_support.h index 58e26abf827..7836f28cda6 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -48,6 +48,7 @@ int fdt_fixup_memory(void *blob, u64 start, u64 size); void fdt_fixup_ethernet(void *fdt, bd_t *bd); int fdt_find_and_setprop(void *fdt, const char *node, const char *prop, const void *val, int len, int create); +void fdt_fixup_qe_firmware(void *fdt); #ifdef CONFIG_OF_HAS_UBOOT_ENV int fdt_env(void *fdt); -- cgit v1.3.1 From 890dfef06c2d169a3356359596890754dfb8ee1c Mon Sep 17 00:00:00 2001 From: Andy Fleming Date: Wed, 9 Jan 2008 16:34:51 -0600 Subject: Remove cache config from ATUM8548 and sbc8548 configs These boards weren't updated by Kumar's config patch because they weren't in the tree, yet. Signed-off-by: Andy Fleming --- include/configs/ATUM8548.h | 7 ------- include/configs/sbc8548.h | 7 ------- 2 files changed, 14 deletions(-) (limited to 'include') diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h index e11a4454362..f7020b49569 100644 --- a/include/configs/ATUM8548.h +++ b/include/configs/ATUM8548.h @@ -388,13 +388,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 30d7b011155..c050a061beb 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -484,13 +484,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - /* * Internal Definitions * -- cgit v1.3.1 From 4d332dbeb08f5863d1ea69d91a00c5499d3a87ed Mon Sep 17 00:00:00 2001 From: Niklaus Giger Date: Thu, 10 Jan 2008 18:50:33 +0100 Subject: ppc4xx: Make Sequoia boot vxWorks vxWorks expects in TLB 0 a entry for the Machine Check interrupt TLB 1 a entry for the RAM TLB 2 a entry for the EBC TLB 3 a entry for the boot flash After changing the baudrate to 9600 I had no problems to boot the vxWorks image as distributed by WindRiver (Revision 2.0/1 from June 18, 2007) Signed-off-by: Niklaus Giger --- board/amcc/sequoia/init.S | 26 ++++++++++++++------------ include/configs/sequoia.h | 1 + 2 files changed, 15 insertions(+), 12 deletions(-) (limited to 'include') diff --git a/board/amcc/sequoia/init.S b/board/amcc/sequoia/init.S index ff6ae669efb..306c92c157e 100644 --- a/board/amcc/sequoia/init.S +++ b/board/amcc/sequoia/init.S @@ -39,15 +39,8 @@ tlbtab: tlbtab_start - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the - * speed up boot process. It is patched after relocation to enable SA_I - */ -#ifndef CONFIG_NAND_SPL - tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G ) -#else - tlbentry( CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 1, AC_R|AC_W|AC_X|SA_G ) -#endif + /* vxWorks needs this as first entry for the Machine Check interrupt */ + tlbentry( 0x40000000, SZ_256M, 0, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) /* TLB-entry for DDR SDRAM (Up to 2GB) */ #ifdef CONFIG_4xx_DCACHE @@ -56,6 +49,18 @@ tlbtab: tlbentry( CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I ) #endif + /* TLB-entry for EBC */ + tlbentry( CFG_BCSR_BASE, SZ_256M, CFG_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) + + /* BOOT_CS (FLASH) must be forth. Before relocation SA_I can be off to use the + * speed up boot process. It is patched after relocation to enable SA_I + */ +#ifndef CONFIG_NAND_SPL + tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G ) +#else + tlbentry( CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 1, AC_R|AC_W|AC_X|SA_G ) +#endif + #ifdef CFG_INIT_RAM_DCACHE /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G ) @@ -67,9 +72,6 @@ tlbtab: tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I ) tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I ) - /* TLB-entry for EBC */ - tlbentry( CFG_BCSR_BASE, SZ_1K, CFG_BCSR_BASE, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) - /* TLB-entry for NAND */ tlbentry( CFG_NAND_ADDR, SZ_1K, CFG_NAND_ADDR, 1, AC_R|AC_W|AC_X|SA_G|SA_I ) diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 8929134b5ff..056c2889bfb 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -61,6 +61,7 @@ #define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ #define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_TLB_FOR_BOOT_FLASH 0x0003 #define CFG_BOOT_BASE_ADDR 0xf0000000 #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -- cgit v1.3.1 From 977b57583a7c34010e566a09a679ec3c1836f996 Mon Sep 17 00:00:00 2001 From: Kim Phillips Date: Wed, 9 Jan 2008 15:24:06 -0600 Subject: mpc83xx: add missing CONFIG_HAS_ETH0 defines the new libfdt code only updates eth0 if CONFIG_HAS_ETH0 is defined; add the define to the missing board configs. Thanks to Emilian Medve for finding this. Signed-off-by: Kim Phillips --- include/configs/MPC8323ERDB.h | 1 + include/configs/MPC832XEMDS.h | 1 + include/configs/MPC8360EMDS.h | 1 + 3 files changed, 3 insertions(+) (limited to 'include') diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 564de02f5b5..3521eb67a01 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -513,6 +513,7 @@ */ #define CONFIG_ENV_OVERWRITE +#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */ #define CONFIG_ETHADDR 00:04:9f:ef:03:01 #define CONFIG_HAS_ETH1 /* add support for "eth1addr" */ #define CONFIG_ETH1ADDR 00:04:9f:ef:03:02 diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index a48b3117b60..5eb5f1290ab 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -575,6 +575,7 @@ #define CONFIG_ENV_OVERWRITE #if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:04:9f:ef:03:01 #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:04:9f:ef:03:02 diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index fedb8a9c5bf..a6755e7cc97 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -606,6 +606,7 @@ #define CONFIG_ENV_OVERWRITE #if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 #define CONFIG_ETHADDR 00:04:9f:ef:01:01 #define CONFIG_HAS_ETH1 #define CONFIG_ETH1ADDR 00:04:9f:ef:01:02 -- cgit v1.3.1 From fab6f556bbbbd1bb35a5433161f7f173c18df559 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Wed, 9 Jan 2008 20:57:47 +0300 Subject: mpc83xx: add support for the MPC8360E-RDK This is MPC8360E based board with: - 256MB fixed SDRAM; - 8MB Intel Strata NOR flash; - StMICRO 64MiB NAND flash; - two 10/100/1000 ethernet ports connected via Broadcom BCM5481 PHYs; - two 10/100 ethernet ports connected via National DP83848 PHYs; - one PCI and one miniPCI slots; - four serial ports (two NS16550-compatible, two UCCs); - four USB ports working through MPC8360E "FHCI" USB controller; - Fujitsu MB86277 graphics controller; - Analog to Digital Converter/Touchscreen controller, AD7843 connected to SPI. Features not supported in this patch are: - StMICRO 64MiB NAND flash (patch sent); - MINT framebuffer initialization (patch is pending); - Fetching production information from the EEPROM via I2C; - FHCI USB; - Two slow UCCs used as RS-485 UARTs. Signed-off-by: Anton Vorontsov Signed-off-by: Kim Phillips --- MAINTAINERS | 4 + MAKEALL | 2 + Makefile | 11 + board/freescale/mpc8360erdk/Makefile | 50 +++ board/freescale/mpc8360erdk/config.mk | 28 ++ board/freescale/mpc8360erdk/mpc8360erdk.c | 340 +++++++++++++++++++ include/configs/MPC8360ERDK.h | 538 ++++++++++++++++++++++++++++++ 7 files changed, 973 insertions(+) create mode 100644 board/freescale/mpc8360erdk/Makefile create mode 100644 board/freescale/mpc8360erdk/config.mk create mode 100644 board/freescale/mpc8360erdk/mpc8360erdk.c create mode 100644 include/configs/MPC8360ERDK.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 2ef2f5c7c49..72429ac0437 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -371,6 +371,10 @@ David Updegraff CRAYL1 PPC4xx +Anton Vorontsov + + MPC8360ERDK MPC8360 + Josef Wagner CPC45 MPC8245 diff --git a/MAKEALL b/MAKEALL index ebc5a225abd..6013d49f523 100755 --- a/MAKEALL +++ b/MAKEALL @@ -313,6 +313,8 @@ LIST_83xx=" \ MPC8349ITXGP \ MPC8360EMDS \ MPC8360EMDS_ATM \ + MPC8360ERDK_33 \ + MPC8360ERDK_66 \ MPC837XEMDS \ sbc8349 \ TQM834x \ diff --git a/Makefile b/Makefile index 1983ca0f13b..47206fc7602 100644 --- a/Makefile +++ b/Makefile @@ -1929,6 +1929,17 @@ MPC8360EMDS_ATM_config: unconfig fi ; @$(MKCONFIG) -a MPC8360EMDS ppc mpc83xx mpc8360emds freescale +MPC8360ERDK_33_config \ +MPC8360ERDK_66_config \ +MPC8360ERDK_config: + @mkdir -p $(obj)include + @echo "" >$(obj)include/config.h ; \ + if [ "$(findstring _33_,$@)" ] ; then \ + echo -n "... CLKIN 33MHz " ; \ + echo "#define CONFIG_CLKIN_33MHZ" >>$(obj)include/config.h ;\ + fi ; + @$(MKCONFIG) -a MPC8360ERDK ppc mpc83xx mpc8360erdk freescale + MPC837XEMDS_config \ MPC837XEMDS_HOST_config: unconfig @mkdir -p $(obj)include diff --git a/board/freescale/mpc8360erdk/Makefile b/board/freescale/mpc8360erdk/Makefile new file mode 100644 index 00000000000..acc954488f5 --- /dev/null +++ b/board/freescale/mpc8360erdk/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc8360erdk/config.mk b/board/freescale/mpc8360erdk/config.mk new file mode 100644 index 00000000000..87dd746a600 --- /dev/null +++ b/board/freescale/mpc8360erdk/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# MPC8360ERDK +# + +TEXT_BASE = 0xFF800000 diff --git a/board/freescale/mpc8360erdk/mpc8360erdk.c b/board/freescale/mpc8360erdk/mpc8360erdk.c new file mode 100644 index 00000000000..98ec6abd279 --- /dev/null +++ b/board/freescale/mpc8360erdk/mpc8360erdk.c @@ -0,0 +1,340 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * Dave Liu + * + * Copyright (C) 2007 Logic Product Development, Inc. + * Peter Barada + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +const qe_iop_conf_t qe_iop_conf_tab[] = { + /* MDIO */ + {0, 1, 3, 0, 2}, /* MDIO */ + {0, 2, 1, 0, 1}, /* MDC */ + + /* UCC1 - UEC (Gigabit) */ + {0, 3, 1, 0, 1}, /* TxD0 */ + {0, 4, 1, 0, 1}, /* TxD1 */ + {0, 5, 1, 0, 1}, /* TxD2 */ + {0, 6, 1, 0, 1}, /* TxD3 */ + {0, 9, 2, 0, 1}, /* RxD0 */ + {0, 10, 2, 0, 1}, /* RxD1 */ + {0, 11, 2, 0, 1}, /* RxD2 */ + {0, 12, 2, 0, 1}, /* RxD3 */ + {0, 7, 1, 0, 1}, /* TX_EN */ + {0, 8, 1, 0, 1}, /* TX_ER */ + {0, 15, 2, 0, 1}, /* RX_DV */ + {0, 0, 2, 0, 1}, /* RX_CLK */ + {2, 9, 1, 0, 3}, /* GTX_CLK - CLK10 */ + {2, 8, 2, 0, 1}, /* GTX125 - CLK9 */ + + /* UCC2 - UEC (Gigabit) */ + {0, 17, 1, 0, 1}, /* TxD0 */ + {0, 18, 1, 0, 1}, /* TxD1 */ + {0, 19, 1, 0, 1}, /* TxD2 */ + {0, 20, 1, 0, 1}, /* TxD3 */ + {0, 23, 2, 0, 1}, /* RxD0 */ + {0, 24, 2, 0, 1}, /* RxD1 */ + {0, 25, 2, 0, 1}, /* RxD2 */ + {0, 26, 2, 0, 1}, /* RxD3 */ + {0, 21, 1, 0, 1}, /* TX_EN */ + {0, 22, 1, 0, 1}, /* TX_ER */ + {0, 29, 2, 0, 1}, /* RX_DV */ + {0, 31, 2, 0, 1}, /* RX_CLK */ + {2, 2, 1, 0, 2}, /* GTX_CLK - CLK10 */ + {2, 3, 2, 0, 1}, /* GTX125 - CLK4 */ + + /* UCC7 - UEC */ + {4, 0, 1, 0, 1}, /* TxD0 */ + {4, 1, 1, 0, 1}, /* TxD1 */ + {4, 2, 1, 0, 1}, /* TxD2 */ + {4, 3, 1, 0, 1}, /* TxD3 */ + {4, 6, 2, 0, 1}, /* RxD0 */ + {4, 7, 2, 0, 1}, /* RxD1 */ + {4, 8, 2, 0, 1}, /* RxD2 */ + {4, 9, 2, 0, 1}, /* RxD3 */ + {4, 4, 1, 0, 1}, /* TX_EN */ + {4, 5, 1, 0, 1}, /* TX_ER */ + {4, 12, 2, 0, 1}, /* RX_DV */ + {4, 13, 2, 0, 1}, /* RX_ER */ + {4, 10, 2, 0, 1}, /* COL */ + {4, 11, 2, 0, 1}, /* CRS */ + {2, 18, 2, 0, 1}, /* TX_CLK - CLK19 */ + {2, 19, 2, 0, 1}, /* RX_CLK - CLK20 */ + + /* UCC4 - UEC */ + {1, 14, 1, 0, 1}, /* TxD0 */ + {1, 15, 1, 0, 1}, /* TxD1 */ + {1, 16, 1, 0, 1}, /* TxD2 */ + {1, 17, 1, 0, 1}, /* TxD3 */ + {1, 20, 2, 0, 1}, /* RxD0 */ + {1, 21, 2, 0, 1}, /* RxD1 */ + {1, 22, 2, 0, 1}, /* RxD2 */ + {1, 23, 2, 0, 1}, /* RxD3 */ + {1, 18, 1, 0, 1}, /* TX_EN */ + {1, 19, 1, 0, 2}, /* TX_ER */ + {1, 26, 2, 0, 1}, /* RX_DV */ + {1, 27, 2, 0, 1}, /* RX_ER */ + {1, 24, 2, 0, 1}, /* COL */ + {1, 25, 2, 0, 1}, /* CRS */ + {2, 6, 2, 0, 1}, /* TX_CLK - CLK7 */ + {2, 7, 2, 0, 1}, /* RX_CLK - CLK8 */ + + /* PCI1 */ + {5, 4, 2, 0, 3}, /* PCI_M66EN */ + {5, 5, 1, 0, 3}, /* PCI_INTA */ + {5, 6, 1, 0, 3}, /* PCI_RSTO */ + {5, 7, 3, 0, 3}, /* PCI_C_BE0 */ + {5, 8, 3, 0, 3}, /* PCI_C_BE1 */ + {5, 9, 3, 0, 3}, /* PCI_C_BE2 */ + {5, 10, 3, 0, 3}, /* PCI_C_BE3 */ + {5, 11, 3, 0, 3}, /* PCI_PAR */ + {5, 12, 3, 0, 3}, /* PCI_FRAME */ + {5, 13, 3, 0, 3}, /* PCI_TRDY */ + {5, 14, 3, 0, 3}, /* PCI_IRDY */ + {5, 15, 3, 0, 3}, /* PCI_STOP */ + {5, 16, 3, 0, 3}, /* PCI_DEVSEL */ + {5, 17, 0, 0, 0}, /* PCI_IDSEL */ + {5, 18, 3, 0, 3}, /* PCI_SERR */ + {5, 19, 3, 0, 3}, /* PCI_PERR */ + {5, 20, 3, 0, 3}, /* PCI_REQ0 */ + {5, 21, 2, 0, 3}, /* PCI_REQ1 */ + {5, 22, 2, 0, 3}, /* PCI_GNT2 */ + {5, 23, 3, 0, 3}, /* PCI_GNT0 */ + {5, 24, 1, 0, 3}, /* PCI_GNT1 */ + {5, 25, 1, 0, 3}, /* PCI_GNT2 */ + {5, 26, 0, 0, 0}, /* PCI_CLK0 */ + {5, 27, 0, 0, 0}, /* PCI_CLK1 */ + {5, 28, 0, 0, 0}, /* PCI_CLK2 */ + {5, 29, 0, 0, 3}, /* PCI_SYNC_OUT */ + {6, 0, 3, 0, 3}, /* PCI_AD0 */ + {6, 1, 3, 0, 3}, /* PCI_AD1 */ + {6, 2, 3, 0, 3}, /* PCI_AD2 */ + {6, 3, 3, 0, 3}, /* PCI_AD3 */ + {6, 4, 3, 0, 3}, /* PCI_AD4 */ + {6, 5, 3, 0, 3}, /* PCI_AD5 */ + {6, 6, 3, 0, 3}, /* PCI_AD6 */ + {6, 7, 3, 0, 3}, /* PCI_AD7 */ + {6, 8, 3, 0, 3}, /* PCI_AD8 */ + {6, 9, 3, 0, 3}, /* PCI_AD9 */ + {6, 10, 3, 0, 3}, /* PCI_AD10 */ + {6, 11, 3, 0, 3}, /* PCI_AD11 */ + {6, 12, 3, 0, 3}, /* PCI_AD12 */ + {6, 13, 3, 0, 3}, /* PCI_AD13 */ + {6, 14, 3, 0, 3}, /* PCI_AD14 */ + {6, 15, 3, 0, 3}, /* PCI_AD15 */ + {6, 16, 3, 0, 3}, /* PCI_AD16 */ + {6, 17, 3, 0, 3}, /* PCI_AD17 */ + {6, 18, 3, 0, 3}, /* PCI_AD18 */ + {6, 19, 3, 0, 3}, /* PCI_AD19 */ + {6, 20, 3, 0, 3}, /* PCI_AD20 */ + {6, 21, 3, 0, 3}, /* PCI_AD21 */ + {6, 22, 3, 0, 3}, /* PCI_AD22 */ + {6, 23, 3, 0, 3}, /* PCI_AD23 */ + {6, 24, 3, 0, 3}, /* PCI_AD24 */ + {6, 25, 3, 0, 3}, /* PCI_AD25 */ + {6, 26, 3, 0, 3}, /* PCI_AD26 */ + {6, 27, 3, 0, 3}, /* PCI_AD27 */ + {6, 28, 3, 0, 3}, /* PCI_AD28 */ + {6, 29, 3, 0, 3}, /* PCI_AD29 */ + {6, 30, 3, 0, 3}, /* PCI_AD30 */ + {6, 31, 3, 0, 3}, /* PCI_AD31 */ + + /* NAND */ + {4, 18, 2, 0, 0}, /* NAND_RYnBY */ + + /* DUART - UART2 */ + {5, 0, 1, 0, 2}, /* UART2_SOUT */ + {5, 2, 1, 0, 1}, /* UART2_RTS */ + {5, 3, 2, 0, 2}, /* UART2_SIN */ + {5, 1, 2, 0, 3}, /* UART2_CTS */ + + /* UCC5 - UART3 */ + {3, 0, 1, 0, 1}, /* UART3_TX */ + {3, 4, 1, 0, 1}, /* UART3_RTS */ + {3, 6, 2, 0, 1}, /* UART3_RX */ + {3, 12, 2, 0, 0}, /* UART3_CTS */ + {3, 13, 2, 0, 0}, /* UCC5_CD */ + + /* UCC6 - UART4 */ + {3, 14, 1, 0, 1}, /* UART4_TX */ + {3, 18, 1, 0, 1}, /* UART4_RTS */ + {3, 20, 2, 0, 1}, /* UART4_RX */ + {3, 26, 2, 0, 0}, /* UART4_CTS */ + {3, 27, 2, 0, 0}, /* UCC6_CD */ + + /* Fujitsu MB86277 (MINT) graphics controller */ + {0, 30, 1, 0, 0}, /* nSRESET_GRAPHICS */ + {1, 5, 1, 0, 0}, /* nXRST_GRAPHICS */ + {1, 7, 1, 0, 0}, /* LVDS_BKLT_CTR */ + {2, 16, 1, 0, 0}, /* LVDS_BKLT_EN */ + + /* END of table */ + {0, 0, 0, 0, QE_IOP_TAB_END}, +}; + +int board_early_init_f(void) +{ + return 0; +} + +int board_early_init_r(void) +{ + void *reg = (void *)(CFG_IMMR + 0x14a8); + u32 val; + + /* + * Because of errata in the UCCs, we have to write to the reserved + * registers to slow the clocks down. + */ + val = in_be32(reg); + /* UCC1 */ + val |= 0x00003000; + /* UCC2 */ + val |= 0x0c000000; + out_be32(reg, val); + + return 0; +} + +int fixed_sdram(void) +{ + volatile immap_t *im = (immap_t *)CFG_IMMR; + u32 msize = 0; + u32 ddr_size; + u32 ddr_size_log2; + + msize = CFG_DDR_SIZE; + for (ddr_size = msize << 20, ddr_size_log2 = 0; + (ddr_size > 1); ddr_size = ddr_size >> 1, ddr_size_log2++) { + if (ddr_size & 1) + return -1; + } + + im->sysconf.ddrlaw[0].ar = + LAWAR_EN | ((ddr_size_log2 - 1) & LAWAR_SIZE); + + im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS; + im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG; + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG; + im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE2; + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL; + udelay(200); + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + + return msize; +} + +long int initdram(int board_type) +{ +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + extern void ddr_enable_ecc(unsigned int dram_size); +#endif + volatile immap_t *im = (immap_t *)CFG_IMMR; + u32 msize = 0; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + /* DDR SDRAM - Main SODIMM */ + im->sysconf.ddrlaw[0].bar = CFG_DDR_BASE & LAWBAR_BAR; + msize = fixed_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC) + /* + * Initialize DDR ECC byte + */ + ddr_enable_ecc(msize * 1024 * 1024); +#endif + + /* return total bus SDRAM size(bytes) -- DDR */ + return (msize * 1024 * 1024); +} + +int checkboard(void) +{ + puts("Board: Freescale/Logic MPC8360ERDK\n"); + return 0; +} + +static struct pci_region pci_regions[] = { + { + .bus_start = CFG_PCI1_MEM_BASE, + .phys_start = CFG_PCI1_MEM_PHYS, + .size = CFG_PCI1_MEM_SIZE, + .flags = PCI_REGION_MEM | PCI_REGION_PREFETCH, + }, + { + .bus_start = CFG_PCI1_MMIO_BASE, + .phys_start = CFG_PCI1_MMIO_PHYS, + .size = CFG_PCI1_MMIO_SIZE, + .flags = PCI_REGION_MEM, + }, + { + .bus_start = CFG_PCI1_IO_BASE, + .phys_start = CFG_PCI1_IO_PHYS, + .size = CFG_PCI1_IO_SIZE, + .flags = PCI_REGION_IO, + }, +}; + +void pci_init_board(void) +{ + volatile immap_t *immr = (volatile immap_t *)CFG_IMMR; + volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; + volatile law83xx_t *pci_law = immr->sysconf.pcilaw; + struct pci_region *reg[] = { pci_regions, }; + +#if defined(PCI_33M) + clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2 | + OCCR_PCICD0 | OCCR_PCICD1 | OCCR_PCICD2 | OCCR_PCICR; + printf("PCI clock is 33MHz\n"); +#else + clk->occr = OCCR_PCICOE0 | OCCR_PCICOE1 | OCCR_PCICOE2; + printf("PCI clock is 66MHz\n"); +#endif + + udelay(2000); + + /* Configure PCI Local Access Windows */ + pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; + + pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; + + mpc83xx_pci_init(1, reg, 0); +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + ft_pci_setup(blob, bd); +} +#endif diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h new file mode 100644 index 00000000000..e6d0c5e98ee --- /dev/null +++ b/include/configs/MPC8360ERDK.h @@ -0,0 +1,538 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * Dave Liu + * + * Copyright (C) 2007 Logic Product Development, Inc. + * Peter Barada + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#undef DEBUG + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ +#define CONFIG_MPC83XX 1 /* MPC83XX family */ +#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ +#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */ + +/* + * System Clock Setup + */ +#ifdef CONFIG_CLKIN_33MHZ +#define CONFIG_83XX_CLKIN 33000000 +#define CONFIG_SYS_CLK_FREQ 33000000 +#define PCI_33M 1 +#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1 +#else +#define CONFIG_83XX_CLKIN 66000000 +#define CONFIG_SYS_CLK_FREQ 66000000 +#define PCI_66M 1 +#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1 +#endif /* CONFIG_CLKIN_33MHZ */ + +/* + * Hardware Reset Configuration Word + */ +#define CFG_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\ + HRCWL_CORE_TO_CSB_2X1 |\ + HRCWL_CE_TO_PLL_1X15) + +#define CFG_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCICKDRV_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_SECONDARY_DDR_DISABLE |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_EARLY) + +/* + * System IO Config + */ +#define CFG_SICRH 0x00000000 +#define CFG_SICRL 0x40000000 + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * IMMR new address + */ +#define CFG_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + +#define CFG_83XX_DDR_USES_CS0 + +#undef CONFIG_DDR_ECC /* support DDR ECC function */ +#undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ + +/* + * DDRCDR - DDR Control Driver Register + */ +#define CFG_DDRCDR_VALUE 0x80080001 + +#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ + +/* + * Manually set up DDR parameters + */ +#define CONFIG_DDR_II +#define CFG_DDR_SIZE 256 /* MB */ +#define CFG_DDRCDR 0x80080001 +#define CFG_DDR_CS0_BNDS 0x0000000f +#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \ + CSCONFIG_COL_BIT_10) +#define CFG_DDR_TIMING_0 0x00330903 +#define CFG_DDR_TIMING_1 0x3835a322 +#define CFG_DDR_TIMING_2 0x00104909 +#define CFG_DDR_TIMING_3 0x00000000 +#define CFG_DDR_CLK_CNTL 0x02000000 +#define CFG_DDR_MODE 0x47800432 +#define CFG_DDR_MODE2 0x8000c000 +#define CFG_DDR_INTERVAL 0x045b0100 +#define CFG_DDR_SDRAM_CFG 0x03000000 +#define CFG_DDR_SDRAM_CFG2 0x00001000 + +/* + * Memory test + */ +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00000000 /* memtest region */ +#define CFG_MEMTEST_END 0x00100000 + +/* + * The reserved memory + */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_FLASH_BASE 0xFF800000 /* FLASH base address */ + +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#else +#undef CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) +#define CFG_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */ +#define CFG_FLASH_PROTECTION 1 /* Use intel Flash protection. */ + +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ +#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ + (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ + BR_V) /* valid */ +#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ + OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \ + OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) + +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CFG_FLASH_CHECKSUM + +/* + * NAND flash on the local bus + */ +#define CFG_NAND_BASE 0x60000000 + +#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE +#define CFG_LBLAWAR1_PRELIM 0x8000001b /* Access window size 4K */ + +/* Port size 8 bit, UPMA */ +#define CFG_BR1_PRELIM (CFG_NAND_BASE | 0x00000881) +#define CFG_OR1_PRELIM 0xfc000001 + +/* + * Fujitsu MB86277 (MINT) graphics controller + */ +#define CFG_VIDEO_BASE 0x70000000 + +#define CFG_LBLAWBAR2_PRELIM CFG_VIDEO_BASE +#define CFG_LBLAWAR2_PRELIM 0x80000019 /* Access window size 64MB */ + +/* Port size 32 bit, UPMB */ +#define CFG_BR2_PRELIM (CFG_VIDEO_BASE | 0x000018a1) /* PS=11, UPMB */ +#define CFG_OR2_PRELIM 0xfc000001 /* (64MB, EAD=1) */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,} + +#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */ +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI 1 + +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_MMIO_BASE 0x90000000 +#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE +#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CFG_PCI1_IO_BASE 0xE0300000 +#define CFG_PCI1_IO_PHYS 0xE0300000 +#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */ + +#ifdef CONFIG_PCI + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "Freescale GETH" + +#define CONFIG_UEC_ETH1 /* GETH1 */ + +#ifdef CONFIG_UEC_ETH1 +#define CFG_UEC1_UCC_NUM 0 /* UCC1 */ +#define CFG_UEC1_RX_CLK QE_CLK_NONE +#define CFG_UEC1_TX_CLK QE_CLK9 +#define CFG_UEC1_ETH_TYPE GIGA_ETH +#define CFG_UEC1_PHY_ADDR 2 +#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII +#endif + +#define CONFIG_UEC_ETH2 /* GETH2 */ + +#ifdef CONFIG_UEC_ETH2 +#define CFG_UEC2_UCC_NUM 1 /* UCC2 */ +#define CFG_UEC2_RX_CLK QE_CLK_NONE +#define CFG_UEC2_TX_CLK QE_CLK4 +#define CFG_UEC2_ETH_TYPE GIGA_ETH +#define CFG_UEC2_PHY_ADDR 4 +#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII +#endif + +/* + * Environment + */ + +#ifndef CFG_RAMBOOT +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CFG_ENV_SIZE 0x20000 +#else /* CFG_RAMBOOT */ +#define CFG_NO_FLASH 1 /* Flash is not usable now */ +#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) +#define CFG_ENV_SIZE 0x2000 +#endif /* CFG_RAMBOOT */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_ASKENV + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +#if defined(CFG_RAMBOOT) +#undef CONFIG_CMD_ENV +#undef CONFIG_CMD_LOADS +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if defined(CONFIG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CFG_HID2 HID2_HBE + +/* + * Cache Config + */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * MMU Setup + */ + +/* DDR: cache cacheable */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +/* IMMRBAR & PCI IO: cache-inhibit and guarded */ +#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U + +/* NAND: cache-inhibit and guarded */ +#define CFG_IBAT2L (CFG_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP) +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT3U CFG_IBAT3U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CFG_IBAT4L (CFG_INIT_RAM_ADDR | BATL_PP_10) +#define CFG_IBAT4U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U + +#define CFG_IBAT5L (CFG_VIDEO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CFG_IBAT5U (CFG_VIDEO_BASE | BATU_BL_64M | BATU_VS | BATU_VP) +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \ + BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#else /* CONFIG_PCI */ +#define CFG_IBAT6L (0) +#define CFG_IBAT6U (0) +#define CFG_IBAT7L (0) +#define CFG_IBAT7U (0) +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U +#endif /* CONFIG_PCI */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#define CONFIG_HAS_ETH3 +#define CONFIG_ETHADDR 00:04:9f:ef:01:01 +#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02 +#define CONFIG_ETH2ADDR 00:04:9f:ef:01:03 +#define CONFIG_ETH3ADDR 00:04:9f:ef:01:04 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR a00000 +#define CONFIG_HOSTNAME mpc8360erdk +#define CONFIG_BOOTFILE uImage + +#define CONFIG_IPADDR 10.0.0.99 +#define CONFIG_SERVERIP 10.0.0.2 +#define CONFIG_GATEWAYIP 10.0.0.2 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_ROOTPATH /nfsroot/ + +#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0"\ + "consoledev=ttyS0\0"\ + "loadaddr=a00000\0"\ + "fdtaddr=900000\0"\ + "bootfile=uImage\0"\ + "fdtfile=dtb\0"\ + "fsfile=fs\0"\ + "ubootfile=u-boot.bin\0"\ + "setbootargs=setenv bootargs console=$consoledev,$baudrate "\ + "$mtdparts panic=1\0"\ + "adddhcpargs=setenv bootargs $bootargs ip=on\0"\ + "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\ + "$gatewayip:$netmask:$hostname:$netdev:off "\ + "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\ + "tftp_get_uboot=tftp 100000 $ubootfile\0"\ + "tftp_get_kernel=tftp $loadaddr $bootfile\0"\ + "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\ + "tftp_get_fs=tftp c00000 $fsfile\0"\ + "nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\ + "cp.b 100000 ff800000 $filesize\0"\ + "boot_m=bootm $loadaddr - $fdtaddr\0"\ + "dhcpboot=run setbootargs adddhcpargs tftp_get_kernel tftp_get_dtb "\ + "boot_m\0"\ + "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\ + "boot_m\0"\ + "" + +#define CONFIG_BOOTCOMMAND "run dhcpboot" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 2c5b48fc205c3e2752910da8f39209ed075929e5 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:03:03 +0800 Subject: mpc83xx: Remove cache config from config.h clean up the cache config from configs.h of board Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/configs/MPC8313ERDB.h | 5 ----- include/configs/MPC8323ERDB.h | 9 --------- include/configs/MPC832XEMDS.h | 9 --------- include/configs/MPC8349EMDS.h | 7 ------- include/configs/MPC8349ITX.h | 9 --------- include/configs/MPC8360EMDS.h | 9 --------- include/configs/MPC837XEMDS.h | 9 --------- include/configs/TQM834x.h | 9 --------- include/configs/sbc8349.h | 7 ------- 9 files changed, 73 deletions(-) (limited to 'include') diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 7bc4e274367..455bbe0cf7d 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -386,11 +386,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 16384 -#define CFG_CACHELINE_SIZE 32 -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ - #define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ #ifdef CFG_66MHZ diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 3521eb67a01..4ea87090c6e 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -422,15 +422,6 @@ #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE -/* - * Cache Config - */ -#define CFG_DCACHE_SIZE 16384 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ -#endif - /* * MMU Setup */ diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 5eb5f1290ab..25ac58c5711 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -481,15 +481,6 @@ #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE -/* - * Cache Config - */ -#define CFG_DCACHE_SIZE 16384 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ -#endif - /* * MMU Setup */ diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 03409bbbafa..437a9a5f7bf 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -527,13 +527,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - #define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ #if 1 /*528/264*/ diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index 49dc0de535e..48c2736fcbe 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -487,15 +487,6 @@ boards, we say we have two, but don't display a message if we find only one. */ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /* log2 of the above value */ -#endif - #define CFG_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_1X1 |\ diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index a6755e7cc97..fdacb904e56 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -511,15 +511,6 @@ #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE -/* - * Cache Config - */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ -#endif - /* * MMU Setup */ diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 0958e6b9679..46fc239c831 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -458,15 +458,6 @@ #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE -/* - * Cache Config - */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ -#endif - /* * MMU Setup */ diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index 01472529d04..8ef3f090855 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -378,15 +378,6 @@ extern int tqm834x_num_flash_banks; */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* - * Cache Configuration - */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - #define CFG_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_1X1 |\ diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 9efe3c49de7..4cc4ff1723f 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -490,13 +490,6 @@ */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - #define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ #if 1 /*528/264*/ -- cgit v1.3.1 From c86ef2cd9ef81935049231fa89f36c7b793f2d4b Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:04:13 +0800 Subject: mpc83xx: Fix the typo in global data struct Fix the typo in global_data.h Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/asm-ppc/global_data.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index 91acf9b7cb2..c3b5e8292e5 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -63,7 +63,7 @@ typedef struct global_data { #if defined (CONFIG_MPC834X) u32 usbmph_clk; #endif /* CONFIG_MPC834X */ -#if defined(CONFIG_MPC815) +#if defined(CONFIG_MPC8315) u32 tdm_clk; #endif #if defined(CONFIG_MPC837X) -- cgit v1.3.1 From ec2638ea08a537a1bd409db873aaaa33a053ebae Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:05:00 +0800 Subject: mpc83xx: Fix the typo in mpc83xx.h The SPCR about TSEC priority is wrong. Signed-off-by: Michael Barkowski Signed-off-by: Joe D'Abbraccio Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/mpc83xx.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/mpc83xx.h b/include/mpc83xx.h index dba1aea4fa9..119f8b1cb74 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -145,10 +145,10 @@ /* SPCR bits - MPC831x and MPC837x specific */ #define SPCR_TSECDP 0x00003000 /* TSEC data priority */ #define SPCR_TSECDP_SHIFT (31-19) -#define SPCR_TSECEP 0x00000C00 /* TSEC emergency priority */ -#define SPCR_TSECEP_SHIFT (31-21) -#define SPCR_TSECBDP 0x00000300 /* TSEC buffer descriptor priority */ -#define SPCR_TSECBDP_SHIFT (31-23) +#define SPCR_TSECBDP 0x00000C00 /* TSEC buffer descriptor priority */ +#define SPCR_TSECBDP_SHIFT (31-21) +#define SPCR_TSECEP 0x00000300 /* TSEC emergency priority */ +#define SPCR_TSECEP_SHIFT (31-23) #endif /* SICRL/H - System I/O Configuration Register Low/High -- cgit v1.3.1 From 6f3931a2bed5412c20d5e5536c865fbd657f7d28 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:06:05 +0800 Subject: mpc83xx: Fix the wrong definition of MPC8315E According to the latest user manual of MPC8315E, 1) The SVCOD of HRCWL is different than 837x 2) The SCCR has changes Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/mpc83xx.h | 48 ++++++++++++++++++++++++++++-------------------- 1 file changed, 28 insertions(+), 20 deletions(-) (limited to 'include') diff --git a/include/mpc83xx.h b/include/mpc83xx.h index 119f8b1cb74..7299ca00bc4 100644 --- a/include/mpc83xx.h +++ b/include/mpc83xx.h @@ -486,7 +486,15 @@ #define HRCWL_CE_TO_PLL_1X30 0x0000001E #define HRCWL_CE_TO_PLL_1X31 0x0000001F -#elif defined(CONFIG_MPC837X) || defined(CONFIG_MPC8315) +#elif defined(CONFIG_MPC8315) +#define HRCWL_SVCOD 0x30000000 +#define HRCWL_SVCOD_SHIFT 28 +#define HRCWL_SVCOD_DIV_2 0x00000000 +#define HRCWL_SVCOD_DIV_4 0x10000000 +#define HRCWL_SVCOD_DIV_8 0x20000000 +#define HRCWL_SVCOD_DIV_1 0x30000000 + +#elif defined(CONFIG_MPC837X) #define HRCWL_SVCOD 0x30000000 #define HRCWL_SVCOD_SHIFT 28 #define HRCWL_SVCOD_DIV_4 0x00000000 @@ -752,31 +760,31 @@ #define SCCR_TSEC2CM_2 0x20000000 #define SCCR_TSEC2CM_3 0x30000000 -#define SCCR_USBDRCM 0x00300000 -#define SCCR_USBDRCM_SHIFT 20 +#define SCCR_USBDRCM 0x00c00000 +#define SCCR_USBDRCM_SHIFT 22 #define SCCR_USBDRCM_0 0x00000000 -#define SCCR_USBDRCM_1 0x00100000 -#define SCCR_USBDRCM_2 0x00200000 -#define SCCR_USBDRCM_3 0x00300000 +#define SCCR_USBDRCM_1 0x00400000 +#define SCCR_USBDRCM_2 0x00800000 +#define SCCR_USBDRCM_3 0x00c00000 -#define SCCR_PCIEXP1CM 0x00080000 -#define SCCR_PCIEXP2CM 0x00040000 +#define SCCR_PCIEXP1CM 0x00300000 +#define SCCR_PCIEXP2CM 0x000c0000 -#define SCCR_SATA1CM 0x0000c000 -#define SCCR_SATA1CM_SHIFT 14 -#define SCCR_SATACM 0x0000f000 -#define SCCR_SATACM_SHIFT 8 +#define SCCR_SATA1CM 0x00003000 +#define SCCR_SATA1CM_SHIFT 12 +#define SCCR_SATACM 0x00003c00 +#define SCCR_SATACM_SHIFT 10 #define SCCR_SATACM_0 0x00000000 -#define SCCR_SATACM_1 0x00005000 -#define SCCR_SATACM_2 0x0000a000 -#define SCCR_SATACM_3 0x0000f000 +#define SCCR_SATACM_1 0x00001400 +#define SCCR_SATACM_2 0x00002800 +#define SCCR_SATACM_3 0x00003c00 -#define SCCR_TDMCM 0x000000c0 -#define SCCR_TDMCM_SHIFT 6 +#define SCCR_TDMCM 0x00000030 +#define SCCR_TDMCM_SHIFT 4 #define SCCR_TDMCM_0 0x00000000 -#define SCCR_TDMCM_1 0x00000040 -#define SCCR_TDMCM_2 0x00000080 -#define SCCR_TDMCM_3 0x000000c0 +#define SCCR_TDMCM_1 0x00000010 +#define SCCR_TDMCM_2 0x00000020 +#define SCCR_TDMCM_3 0x00000030 #elif defined(CONFIG_MPC837X) /* SCCR bits - MPC837x specific */ -- cgit v1.3.1 From 7e74d63d1a211fbc34ec424e2dc6726601f323d0 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:07:23 +0800 Subject: mpc83xx: Reduce the latency of DDR Reduce the AL from 2 to 1 clock to improve the performance. Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/configs/MPC837XEMDS.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'include') diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 46fc239c831..0b4e562bc57 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -132,7 +132,7 @@ #else /* * Manually set up DDR parameters - * WHITE ELECTRONIC DESGGNS - W3HG64M72EEU403PD4 SO-DIMM + * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 */ #define CFG_DDR_SIZE 512 /* MB */ @@ -160,22 +160,22 @@ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) /* 0x3935d322 */ -#define CFG_DDR_TIMING_2 ( ( 2 << TIMING_CFG2_ADD_LAT_SHIFT ) \ +#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) - /* 0x231088c8 */ + /* 0x131088c8 */ #define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) /* 0x03E00100 */ #define CFG_DDR_SDRAM_CFG 0x43000000 #define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ -#define CFG_DDR_MODE ( ( 0x0450 << SDRAM_MODE_ESD_SHIFT ) \ +#define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \ | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) - /* ODT 150ohm CL=3, AL=2 on SDRAM */ + /* ODT 150ohm CL=3, AL=1 on SDRAM */ #define CFG_DDR_MODE2 0x00000000 #endif -- cgit v1.3.1 From ded08317ad9e340b887bf2eb46e9565a0f610a93 Mon Sep 17 00:00:00 2001 From: Dave Liu Date: Thu, 10 Jan 2008 23:08:26 +0800 Subject: mpc83xx: Make the code more readable Format the code, make it more readable Signed-off-by: Dave Liu Signed-off-by: Kim Phillips --- include/configs/MPC837XEMDS.h | 19 +++++++++++++------ 1 file changed, 13 insertions(+), 6 deletions(-) (limited to 'include') diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index 0b4e562bc57..2b84e9cd9c5 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -227,12 +227,19 @@ #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ -#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ - (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ - BR_V) /* valid */ -#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ - OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ - OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) +#define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \ + | (2 << BR_PS_SHIFT) /* 16 bit port size */ \ + | BR_V ) /* valid */ +#define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_0b11 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX \ + | OR_GPCM_EHTR \ + | OR_GPCM_EAD ) + /* 0xFE000FF7 */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ -- cgit v1.3.1 From ff41ffc93c1592e77a44bdbebd5d781739f3aae0 Mon Sep 17 00:00:00 2001 From: Matthias Fuchs Date: Fri, 11 Jan 2008 14:55:16 +0100 Subject: ppc4xx: Update PMC440 config file Signed-off-by: Matthias Fuchs --- include/configs/PMC440.h | 16 +++------------- 1 file changed, 3 insertions(+), 13 deletions(-) (limited to 'include') diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index 87fca3c470f..67bf4b179d9 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -41,7 +41,9 @@ #define CONFIG_SYS_CLK_FREQ 33333400 +#if 0 /* temporary disabled because OS/9 does not like dcache on startup */ #define CONFIG_4xx_DCACHE /* enable dcache */ +#endif #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -272,6 +274,7 @@ CFG_BOOTFILE \ CFG_ROOTPATH \ "netdev=eth0\0" \ + "ethrotate=no\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -354,10 +357,6 @@ #define CONFIG_CMD_SDRAM /* POST support */ -/* ethernet POST sometimes freezes the CPU. - * So disable it for now until issue is solved - */ -#if 0 #define CONFIG_POST (CFG_POST_MEMORY | \ CFG_POST_CPU | \ CFG_POST_UART | \ @@ -366,15 +365,6 @@ CFG_POST_FPU | \ CFG_POST_ETHER | \ CFG_POST_SPR) -#else -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_FPU | \ - CFG_POST_SPR) -#endif #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -- cgit v1.3.1 From d610a60730b7464f6f659db49d264d89a7c71061 Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Fri, 11 Jan 2008 15:31:09 +0100 Subject: ppc4xx: Rework Lime support for lwmon5 Rework Lime support for lwmon5 using new video driver Signed-off-by: Anatolij Gustschin --- board/lwmon5/lwmon5.c | 157 +++++++++++++++++++++++++---------------------- include/configs/lwmon5.h | 16 +++++ 2 files changed, 101 insertions(+), 72 deletions(-) (limited to 'include') diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c index 9b24a7e55e5..815c01f4e48 100644 --- a/board/lwmon5/lwmon5.c +++ b/board/lwmon5/lwmon5.c @@ -233,78 +233,6 @@ int misc_init_r(void) reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP; mtdcr(plb4_acr, reg); - /* - * Reset Lime controller - */ - gpio_write_bit(CFG_GPIO_LIME_S, 1); - udelay(500); - gpio_write_bit(CFG_GPIO_LIME_RST, 1); - - /* Lime memory clock adjusted to 100MHz */ - out_be32((void *)CFG_LIME_SDRAM_CLOCK, CFG_LIME_CLOCK_100MHZ); - /* Wait untill time expired. Because of requirements in lime manual */ - udelay(300); - /* Write lime controller memory parameters */ - out_be32((void *)CFG_LIME_MMR, CFG_LIME_MMR_VALUE); - - /* - * Init display controller - */ - /* Setup dot clock (internal PLL, division rate 1/16) */ - out_be32((void *)0xc1fd0100, 0x00000f00); - - /* Lime L0 init (16 bpp, 640x480) */ - out_be32((void *)0xc1fd0020, 0x801401df); - out_be32((void *)0xc1fd0024, 0x0); - out_be32((void *)0xc1fd0028, 0x0); - out_be32((void *)0xc1fd002c, 0x0); - out_be32((void *)0xc1fd0110, 0x0); - out_be32((void *)0xc1fd0114, 0x0); - out_be32((void *)0xc1fd0118, 0x01df0280); - - /* Display timing init */ - out_be32((void *)0xc1fd0004, 0x031f0000); - out_be32((void *)0xc1fd0008, 0x027f027f); - out_be32((void *)0xc1fd000c, 0x015f028f); - out_be32((void *)0xc1fd0010, 0x020c0000); - out_be32((void *)0xc1fd0014, 0x01df01ea); - out_be32((void *)0xc1fd0018, 0x0); - out_be32((void *)0xc1fd001c, 0x01e00280); - -#if 1 - /* - * Clear framebuffer using Lime's drawing engine - * (draw blue rect. with white border around it) - */ - /* Setup mode and fbbase, xres, fg, bg */ - out_be32((void *)0xc1ff0420, 0x8300); - out_be32((void *)0xc1ff0440, 0x0000); - out_be32((void *)0xc1ff0444, 0x0280); - out_be32((void *)0xc1ff0480, 0x7fff); - out_be32((void *)0xc1ff0484, 0x0000); - /* Reset clipping rectangle */ - out_be32((void *)0xc1ff0454, 0x0000); - out_be32((void *)0xc1ff0458, 0x0280); - out_be32((void *)0xc1ff045c, 0x0000); - out_be32((void *)0xc1ff0460, 0x01e0); - /* Draw white rect. */ - out_be32((void *)0xc1ff04a0, 0x09410000); - out_be32((void *)0xc1ff04a0, 0x00000000); - out_be32((void *)0xc1ff04a0, 0x01e00280); - udelay(2000); - /* Draw blue rect. */ - out_be32((void *)0xc1ff0480, 0x001f); - out_be32((void *)0xc1ff04a0, 0x09410000); - out_be32((void *)0xc1ff04a0, 0x00010001); - out_be32((void *)0xc1ff04a0, 0x01de027e); -#endif - /* Display enable, L0 layer */ - out_be32((void *)0xc1fd0100, 0x80010f00); - - /* TFT-LCD enable - PWM duty, lamp on */ - out_be32((void *)0xc4000024, 0x64); - out_be32((void *)0xc4000020, 0x701); - /* * Init matrix keyboard */ @@ -562,3 +490,88 @@ U_BOOT_CMD( "eepromwp- eeprom write protect off/on\n", " - enable (on) or disable (off) I2C EEPROM write protect\n" ); + +#if defined(CONFIG_VIDEO) +#include +#include + +extern GraphicDevice mb862xx; + +static const gdc_regs init_regs [] = +{ + {0x0100, 0x00000f00}, + {0x0020, 0x801401df}, + {0x0024, 0x00000000}, + {0x0028, 0x00000000}, + {0x002c, 0x00000000}, + {0x0110, 0x00000000}, + {0x0114, 0x00000000}, + {0x0118, 0x01df0280}, + {0x0004, 0x031f0000}, + {0x0008, 0x027f027f}, + {0x000c, 0x015f028f}, + {0x0010, 0x020c0000}, + {0x0014, 0x01df01ea}, + {0x0018, 0x00000000}, + {0x001c, 0x01e00280}, + {0x0100, 0x80010f00}, + {0x0, 0x0} +}; + +const gdc_regs *board_get_regs (void) +{ + return init_regs; +} + +/* Returns Lime base address */ +unsigned int board_video_init (void) +{ + /* + * Reset Lime controller + */ + gpio_write_bit(CFG_GPIO_LIME_S, 1); + udelay(500); + gpio_write_bit(CFG_GPIO_LIME_RST, 1); + + /* Lime memory clock adjusted to 100MHz */ + out_be32((void *)CFG_LIME_SDRAM_CLOCK, CFG_LIME_CLOCK_100MHZ); + /* Wait untill time expired. Because of requirements in lime manual */ + udelay(300); + /* Write lime controller memory parameters */ + out_be32((void *)CFG_LIME_MMR, CFG_LIME_MMR_VALUE); + + mb862xx.winSizeX = 640; + mb862xx.winSizeY = 480; + mb862xx.gdfBytesPP = 2; + mb862xx.gdfIndex = GDF_15BIT_555RGB; + + return CFG_LIME_BASE_0; +} + +void board_backlight_switch (int flag) +{ + if (flag) { + /* pwm duty, lamp on */ + out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000024), 0x64); + out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000020), 0x701); + } else { + /* lamp off */ + out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000024), 0x00); + out_be32((void *)(CFG_FPGA_BASE_0 + 0x00000020), 0x00); + } +} + +#if defined(CONFIG_CONSOLE_EXTRA_INFO) +/* + * Return text to be printed besides the logo. + */ +void video_get_info_str (int line_number, char *info) +{ + if (line_number == 1) { + strcpy (info, " Board: Lwmon5 (Liebherr Elektronik GmbH)"); + } else { + info [0] = '\0'; + } +} +#endif +#endif /* CONFIG_VIDEO */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 0bf536b6b59..c5c2724dd2d 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -248,6 +248,18 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 1 +/* Video console */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO +#define VIDEO_FB_16BPP_PIXEL_SWAP + +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_SPLASH_SCREEN + /* USB */ #ifdef CONFIG_440EPX #define CONFIG_USB_OHCI @@ -294,6 +306,10 @@ #define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP +#endif + #ifdef CONFIG_440EPX #define CONFIG_CMD_USB #endif -- cgit v1.3.1 From bed53753dd1d7e6bcbea4339be0fb7760214cc35 Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Fri, 11 Jan 2008 14:30:01 +0100 Subject: Add Fujitsu CoralP/Lime video driver Signed-off-by: Anatolij Gustschin Signed-off-by: Rodolfo Giometti --- drivers/video/Makefile | 1 + drivers/video/cfb_console.c | 42 +++++ drivers/video/mb862xx.c | 414 ++++++++++++++++++++++++++++++++++++++++++++ include/mb862xx.h | 44 +++++ 4 files changed, 501 insertions(+) create mode 100644 drivers/video/mb862xx.c create mode 100644 include/mb862xx.h (limited to 'include') diff --git a/drivers/video/Makefile b/drivers/video/Makefile index 36611ecdda9..0e40f2afa98 100644 --- a/drivers/video/Makefile +++ b/drivers/video/Makefile @@ -28,6 +28,7 @@ LIB := $(obj)libvideo.a COBJS-y += ati_radeon_fb.o COBJS-y += cfb_console.o COBJS-y += ct69000.o +COBJS-y += mb862xx.o COBJS-y += sed13806.o COBJS-y += sed156x.o COBJS-y += sm501.o diff --git a/drivers/video/cfb_console.c b/drivers/video/cfb_console.c index 6262d02510c..4f73067251e 100644 --- a/drivers/video/cfb_console.c +++ b/drivers/video/cfb_console.c @@ -140,6 +140,18 @@ CONFIG_VIDEO_HW_CURSOR: - Uses the hardware cursor capability of the #endif #endif +/*****************************************************************************/ +/* Defines for the MB862xx driver */ +/*****************************************************************************/ +#ifdef CONFIG_VIDEO_MB862xx + +#ifdef CONFIG_VIDEO_CORALP +#define VIDEO_FB_LITTLE_ENDIAN +#endif +#define VIDEO_HW_RECTFILL +#define VIDEO_HW_BITBLT +#endif + /*****************************************************************************/ /* Include video_fb.h after definitions of VIDEO_HW_RECTFILL etc */ /*****************************************************************************/ @@ -304,7 +316,11 @@ void console_cursor (int state); #else #define SWAP16(x) (x) #define SWAP32(x) (x) +#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP) #define SHORTSWAP32(x) (x) +#else +#define SHORTSWAP32(x) ( ((x) >> 16) | ((x) << 16) ) +#endif #endif #if defined(DEBUG) || defined(DEBUG_CFB_CONSOLE) @@ -735,10 +751,24 @@ void video_puts (const char *s) fb ++; \ } +#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP) #define FILL_15BIT_555RGB(r,g,b) { \ *(unsigned short *)fb = SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3))); \ fb += 2; \ } +#else +static int tgl; +static unsigned short p0; +#define FILL_15BIT_555RGB(r,g,b) { \ + if (!tgl++) { \ + p0 = SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3))); \ + } else { \ + tgl=0; \ + *(unsigned long *)(fb-2) = (SWAP16((unsigned short)(((r>>3)<<10) | ((g>>3)<<5) | (b>>3)))<<16) | p0; \ + } \ + fb += 2; \ +} +#endif #define FILL_16BIT_565RGB(r,g,b) { \ *(unsigned short *)fb = SWAP16((unsigned short)((((r)>>3)<<11) | (((g)>>2)<<5) | ((b)>>3))); \ @@ -1080,8 +1110,20 @@ void logo_plot (void *screen, int width, int x, int y) *dest = ((r >> 5) << 5) | ((g >> 5) << 2) | (b >> 6); break; case GDF_15BIT_555RGB: +#if !defined(VIDEO_FB_16BPP_PIXEL_SWAP) *(unsigned short *) dest = SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3))); +#else + { + if (!tgl++) { + p0 = SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3))); + } else { + *(unsigned long *)(dest-2) = + (SWAP16 ((unsigned short) (((r >> 3) << 10) | ((g >> 3) << 5) | (b >> 3)))<<16) | p0; + tgl=0; + } + } +#endif break; case GDF_16BIT_565RGB: *(unsigned short *) dest = diff --git a/drivers/video/mb862xx.c b/drivers/video/mb862xx.c new file mode 100644 index 00000000000..bfb057f513b --- /dev/null +++ b/drivers/video/mb862xx.c @@ -0,0 +1,414 @@ +/* + * (C) Copyright 2007 + * DENX Software Engineering, Anatolij Gustschin, agust@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mb862xx.c - Graphic interface for Fujitsu CoralP/Lime + * PCI and video mode code was derived from smiLynxEM driver. + */ + +#include + +#if defined(CONFIG_VIDEO_MB862xx) + +#include +#include +#include +#include "videomodes.h" +#include + +/* + * Graphic Device + */ +GraphicDevice mb862xx; + +/* + * 32MB external RAM - 256K Chip MMIO = 0x1FC0000 ; + */ +#define VIDEO_MEM_SIZE 0x01FC0000 + +#if defined(CONFIG_PCI) +#if defined(CONFIG_VIDEO_CORALP) + +static struct pci_device_id supported[] = { + { PCI_VENDOR_ID_FUJITSU, PCI_DEVICE_ID_CORAL_P }, + { PCI_VENDOR_ID_FUJITSU, PCI_DEVICE_ID_CORAL_PA }, + { } +}; + +/* Internal clock frequency divider table, index is mode number */ +unsigned int fr_div[] = { 0x00000f00, 0x00000900, 0x00000500 }; +#endif +#endif + +#if defined(CONFIG_VIDEO_CORALP) +#define rd_io in32r +#define wr_io out32r +#else +#define rd_io(addr) in_be32((volatile unsigned*)(addr)) +#define wr_io(addr,val) out_be32((volatile unsigned*)(addr), (val)) +#endif + +#define HOST_RD_REG(off) rd_io((pGD->frameAdrs + 0x01fc0000 + (off))) +#define HOST_WR_REG(off, val) wr_io((pGD->frameAdrs + 0x01fc0000 + (off)), (val)) +#define DISP_RD_REG(off) rd_io((pGD->frameAdrs + 0x01fd0000 + (off))) +#define DISP_WR_REG(off, val) wr_io((pGD->frameAdrs + 0x01fd0000 + (off)), (val)) +#define DE_RD_REG(off) rd_io((pGD->dprBase + (off))) +#define DE_WR_REG(off, val) wr_io((pGD->dprBase + (off)), (val)) + +#if defined(CONFIG_VIDEO_CORALP) +#define DE_WR_FIFO(val) wr_io((pGD->dprBase + (0x8400)), (val)) +#else +#define DE_WR_FIFO(val) wr_io((pGD->dprBase + (0x04a0)), (val)) +#endif + +#define L0PAL_RD_REG(idx, val) rd_io((pGD->frameAdrs + 0x01fd0400 + ((idx)<<2))) +#define L0PAL_WR_REG(idx, val) wr_io((pGD->frameAdrs + 0x01fd0400 + ((idx)<<2)), (val)) +#define L1PAL_RD_REG(idx, val) rd_io((pGD->frameAdrs + 0x01fd0800 + ((idx)<<2))) +#define L1PAL_WR_REG(idx, val) wr_io((pGD->frameAdrs + 0x01fd0800 + ((idx)<<2)), (val)) +#define L2PAL_RD_REG(idx, val) rd_io((pGD->frameAdrs + 0x01fd1000 + ((idx)<<2))) +#define L2PAL_WR_REG(idx, val) wr_io((pGD->frameAdrs + 0x01fd1000 + ((idx)<<2)), (val)) +#define L3PAL_RD_REG(idx, val) rd_io((pGD->frameAdrs + 0x01fd1400 + ((idx)<<2))) +#define L3PAL_WR_REG(idx, val) wr_io((pGD->frameAdrs + 0x01fd1400 + ((idx)<<2)), (val)) + +static void gdc_sw_reset(void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + HOST_WR_REG (0x002c, 0x00000001); + udelay (500); + video_hw_init (); +} + + +static void de_wait(void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + int lc = 0x10000; + + /* Sync with software writes to framebuffer, + try to reset if engine locked */ + while (DE_RD_REG (0x0400) & 0x00000131) + if (lc-- < 0) { + gdc_sw_reset (); + printf ("gdc reset done after drawing engine lock...\n"); + break; + } +} + +static void de_wait_slots(int slots) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + int lc = 0x10000; + + /* Wait for free fifo slots */ + while (DE_RD_REG (0x0408) < slots) + if (lc-- < 0) { + gdc_sw_reset (); + printf ("gdc reset done after drawing engine lock...\n"); + break; + } +} + +#if !defined(CONFIG_VIDEO_CORALP) +static void board_disp_init(void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + const gdc_regs *regs = board_get_regs (); + + while (regs->index) { + DISP_WR_REG (regs->index, regs->value); + regs++; + } +} +#endif + +/* + * Init drawing engine + */ +static void de_init (void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + int cf = (pGD->gdfBytesPP == 1) ? 0x0000 : 0x8000; + + pGD->dprBase = pGD->frameAdrs + 0x01ff0000; + + /* Setup mode and fbbase, xres, fg, bg */ + de_wait_slots (2); + DE_WR_FIFO (0xf1010108); + DE_WR_FIFO (cf | 0x0300); + DE_WR_REG (0x0440, 0x0000); + DE_WR_REG (0x0444, pGD->winSizeX); + DE_WR_REG (0x0480, 0x0000); + DE_WR_REG (0x0484, 0x0000); + /* Reset clipping */ + DE_WR_REG (0x0454, 0x0000); + DE_WR_REG (0x0458, pGD->winSizeX); + DE_WR_REG (0x045c, 0x0000); + DE_WR_REG (0x0460, pGD->winSizeY); + + /* Clear framebuffer using drawing engine */ + de_wait_slots (3); + DE_WR_FIFO (0x09410000); + DE_WR_FIFO (0x00000000); + DE_WR_FIFO (pGD->winSizeY<<16 | pGD->winSizeX); +} + +#if defined(CONFIG_VIDEO_CORALP) +unsigned int pci_video_init(void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + pci_dev_t devbusfn; + + if ((devbusfn = pci_find_devices(supported, 0)) < 0) + { + printf ("PCI video controller not found!\n"); + return 0; + } + + /* PCI setup */ + pci_write_config_dword (devbusfn, PCI_COMMAND, (PCI_COMMAND_MEMORY | PCI_COMMAND_IO)); + pci_read_config_dword (devbusfn, PCI_BASE_ADDRESS_0, &pGD->frameAdrs); + pGD->frameAdrs = pci_mem_to_phys (devbusfn, pGD->frameAdrs); + + if (pGD->frameAdrs == 0) { + printf ("PCI config: failed to get base address\n"); + return 0; + } + + pGD->pciBase = pGD->frameAdrs; + + /* Setup clocks and memory mode for Coral-P Eval. Board */ + HOST_WR_REG (0x0038, 0x00090000); + udelay (200); + HOST_WR_REG (0xfffc, 0x11d7fa13); + udelay (100); + return pGD->frameAdrs; +} + +unsigned int card_init (void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + unsigned int cf, videomode, div = 0; + unsigned long t1, hsync, vsync; + char *penv; + int tmp, i, bpp; + struct ctfb_res_modes *res_mode; + struct ctfb_res_modes var_mode; + + memset (pGD, 0, sizeof (GraphicDevice)); + + if (!pci_video_init ()) { + return 0; + } + + printf ("CoralP\n"); + + tmp = 0; + videomode = 0x310; + /* get video mode via environment */ + if ((penv = getenv ("videomode")) != NULL) { + /* deceide if it is a string */ + if (penv[0] <= '9') { + videomode = (int) simple_strtoul (penv, NULL, 16); + tmp = 1; + } + } else { + tmp = 1; + } + if (tmp) { + /* parameter are vesa modes */ + /* search params */ + for (i = 0; i < VESA_MODES_COUNT; i++) { + if (vesa_modes[i].vesanr == videomode) + break; + } + if (i == VESA_MODES_COUNT) { + printf ("\tno VESA Mode found, switching to mode 0x%x \n", videomode); + i = 0; + } + res_mode = + (struct ctfb_res_modes *) &res_mode_init[vesa_modes[i].resindex]; + if (vesa_modes[i].resindex > 2) { + printf ("\tUnsupported resolution, switching to default\n"); + bpp = vesa_modes[1].bits_per_pixel; + div = fr_div[1]; + } + bpp = vesa_modes[i].bits_per_pixel; + div = fr_div[vesa_modes[i].resindex]; + } else { + + res_mode = (struct ctfb_res_modes *) &var_mode; + bpp = video_get_params (res_mode, penv); + } + + /* calculate hsync and vsync freq (info only) */ + t1 = (res_mode->left_margin + res_mode->xres + + res_mode->right_margin + res_mode->hsync_len) / 8; + t1 *= 8; + t1 *= res_mode->pixclock; + t1 /= 1000; + hsync = 1000000000L / t1; + t1 *= (res_mode->upper_margin + res_mode->yres + + res_mode->lower_margin + res_mode->vsync_len); + t1 /= 1000; + vsync = 1000000000L / t1; + + /* fill in Graphic device struct */ + sprintf (pGD->modeIdent, "%dx%dx%d %ldkHz %ldHz", res_mode->xres, + res_mode->yres, bpp, (hsync / 1000), (vsync / 1000)); + printf ("\t%s\n", pGD->modeIdent); + pGD->winSizeX = res_mode->xres; + pGD->winSizeY = res_mode->yres; + pGD->memSize = VIDEO_MEM_SIZE; + + switch (bpp) { + case 8: + pGD->gdfIndex = GDF__8BIT_INDEX; + pGD->gdfBytesPP = 1; + break; + case 15: + case 16: + pGD->gdfIndex = GDF_15BIT_555RGB; + pGD->gdfBytesPP = 2; + break; + default: + printf ("\t%d bpp configured, but only 8,15 and 16 supported.\n", bpp); + printf ("\tSwitching back to 15bpp\n"); + pGD->gdfIndex = GDF_15BIT_555RGB; + pGD->gdfBytesPP = 2; + } + + /* Setup dot clock (internal pll, division rate) */ + DISP_WR_REG (0x0100, div); + /* L0 init */ + cf = (pGD->gdfBytesPP == 1) ? 0x00000000 : 0x80000000; + DISP_WR_REG (0x0020, ((pGD->winSizeX * pGD->gdfBytesPP)/64)<<16 | + (pGD->winSizeY-1) | + cf); + DISP_WR_REG (0x0024, 0x00000000); + DISP_WR_REG (0x0028, 0x00000000); + DISP_WR_REG (0x002c, 0x00000000); + DISP_WR_REG (0x0110, 0x00000000); + DISP_WR_REG (0x0114, 0x00000000); + DISP_WR_REG (0x0118, (pGD->winSizeY-1)<<16 | pGD->winSizeX); + + /* Display timing init */ + DISP_WR_REG (0x0004, (pGD->winSizeX+res_mode->left_margin+res_mode->right_margin+res_mode->hsync_len-1)<<16); + DISP_WR_REG (0x0008, (pGD->winSizeX-1) << 16 | (pGD->winSizeX-1)); + DISP_WR_REG (0x000c, (res_mode->vsync_len-1)<<24|(res_mode->hsync_len-1)<<16|(pGD->winSizeX+res_mode->right_margin-1)); + DISP_WR_REG (0x0010, (pGD->winSizeY+res_mode->lower_margin+res_mode->upper_margin+res_mode->vsync_len-1)<<16); + DISP_WR_REG (0x0014, (pGD->winSizeY-1) << 16 | (pGD->winSizeY+res_mode->lower_margin-1)); + DISP_WR_REG (0x0018, 0x00000000); + DISP_WR_REG (0x001c, pGD->winSizeY << 16 | pGD->winSizeX); + /* Display enable, L0 layer */ + DISP_WR_REG (0x0100, 0x80010000 | div); + + return pGD->frameAdrs; +} +#endif + +void *video_hw_init (void) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + + printf ("Video: Fujitsu "); + + memset (pGD, 0, sizeof (GraphicDevice)); + +#if defined(CONFIG_VIDEO_CORALP) + if (card_init () == 0) { + return (NULL); + } +#else + /* Preliminary init of the onboard graphic controller, + retrieve base address */ + if ((pGD->frameAdrs = board_video_init ()) == 0) { + printf ("Controller not found!\n"); + return (NULL); + } else + printf("Lime\n"); +#endif + + de_init (); + +#if !defined(CONFIG_VIDEO_CORALP) + board_disp_init(); +#endif + +#if defined(CONFIG_LWMON5) + /* Lamp on */ + board_backlight_switch (1); +#endif + + return pGD; +} + +/* + * Set a RGB color in the LUT + */ +void video_set_lut (unsigned int index, unsigned char r, unsigned char g, unsigned char b) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + + L0PAL_WR_REG (index, (r << 16) | (g << 8) | (b)); +} + +/* + * Drawing engine Fill and BitBlt screen region + */ +void video_hw_rectfill (unsigned int bpp, unsigned int dst_x, unsigned int dst_y, + unsigned int dim_x, unsigned int dim_y, unsigned int color) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + + de_wait_slots (3); + DE_WR_REG (0x0480, color); + DE_WR_FIFO (0x09410000); + DE_WR_FIFO ((dst_y << 16) | dst_x); + DE_WR_FIFO ((dim_y << 16) | dim_x); + de_wait (); +} + +void video_hw_bitblt (unsigned int bpp, unsigned int src_x, unsigned int src_y, + unsigned int dst_x, unsigned int dst_y, unsigned int width, + unsigned int height) +{ + GraphicDevice *pGD = (GraphicDevice *)&mb862xx; + unsigned int ctrl = 0x0d000000L; + + if (src_x >= dst_x && src_y >= dst_y) + ctrl |= 0x00440000L; + else if (src_x >= dst_x && src_y <= dst_y) + ctrl |= 0x00460000L; + else if (src_x <= dst_x && src_y >= dst_y) + ctrl |= 0x00450000L; + else + ctrl |= 0x00470000L; + + de_wait_slots (4); + DE_WR_FIFO (ctrl); + DE_WR_FIFO ((src_y << 16) | src_x); + DE_WR_FIFO ((dst_y << 16) | dst_x); + DE_WR_FIFO ((height << 16) | width); + de_wait (); /* sync */ +} +#endif /* CONFIG_VIDEO_MB862xx */ diff --git a/include/mb862xx.h b/include/mb862xx.h new file mode 100644 index 00000000000..1af567002eb --- /dev/null +++ b/include/mb862xx.h @@ -0,0 +1,44 @@ +/* + * (C) Copyright 2007 + * DENX Software Engineering, Anatolij Gustschin, agust@denx.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mb862xx.h - Graphic interface for Fujitsu CoralP/Lime + */ + +#ifndef _MB862XX_H_ +#define _MB862XX_H_ + +#define PCI_VENDOR_ID_FUJITSU 0x10CF +#define PCI_DEVICE_ID_CORAL_P 0x2019 +#define PCI_DEVICE_ID_CORAL_PA 0x201E + +typedef struct { + unsigned int index; + unsigned int value; +} gdc_regs; + +const gdc_regs *board_get_regs (void); +unsigned int board_video_init (void); +void board_backlight_switch(int); + +#endif /* _MB862XX_H_ */ -- cgit v1.3.1 From efc6f447c1b940d1650c4b854c5598a595ddc3da Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 10 Jan 2008 17:59:07 +0100 Subject: Add support for the TK885D baseboard from TELE-DATA The TK885D board uses a TQM885D module from TQ, this port adds an own configuration file and adds a last_stage_init() method to configure the two PHYs, depending on the phy_auto_nego environment variable. Signed-off-by: Guennadi Liakhovetski --- MAKEALL | 1 + Makefile | 1 + board/tqm8xx/tqm8xx.c | 47 +++++ include/configs/TK885D.h | 513 +++++++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 562 insertions(+) create mode 100644 include/configs/TK885D.h (limited to 'include') diff --git a/MAKEALL b/MAKEALL index 6013d49f523..cb1322d7c93 100755 --- a/MAKEALL +++ b/MAKEALL @@ -135,6 +135,7 @@ LIST_8xx=" \ SPD823TS \ svm_sc8xx \ SXNI855T \ + TK885D \ TOP860 \ TQM823L \ TQM823L_LCD \ diff --git a/Makefile b/Makefile index 47206fc7602..fa12ed7cef8 100644 --- a/Makefile +++ b/Makefile @@ -1062,6 +1062,7 @@ TQM860M_config \ TQM862M_config \ TQM866M_config \ TQM885D_config \ +TK885D_config \ virtlab2_config: unconfig @mkdir -p $(obj)include @ >$(obj)include/config.h diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c index fcd941e0d2d..18bf2a83029 100644 --- a/board/tqm8xx/tqm8xx.c +++ b/board/tqm8xx/tqm8xx.c @@ -504,4 +504,51 @@ int misc_init_r (void) } #endif /* CONFIG_NSCU */ +/* ---------------------------------------------------------------------------- */ +/* TK885D specific initializaion */ +/* ---------------------------------------------------------------------------- */ +#ifdef CONFIG_TK885D +#include +int last_stage_init(void) +{ + const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY}; + unsigned short reg; + int ret, i = 100; + char *s; + + mii_init(); + /* Without this delay 0xff is read from the UART buffer later in + * abortboot() and autoboot is aborted */ + udelay(10000); + while (tstc() && i--) + (void)getc(); + + /* Check if auto-negotiation is prohibited */ + s = getenv("phy_auto_nego"); + + if (!s || !strcmp(s, "on")) + /* Nothing to do - autonegotiation by default */ + return 0; + + for (i = 0; i < 2; i++) { + ret = miiphy_read("FEC ETHERNET", phy[i], PHY_BMCR, ®); + if (ret) { + printf("Cannot read BMCR on PHY %d\n", phy[i]); + return 0; + } + /* Auto-negotiation off, hard set full duplex, 100Mbps */ + ret = miiphy_write("FEC ETHERNET", phy[i], + PHY_BMCR, (reg | PHY_BMCR_100MB | + PHY_BMCR_DPLX) & ~PHY_BMCR_AUTON); + if (ret) { + printf("Cannot write BMCR on PHY %d\n", phy[i]); + return 0; + } + } + + return 0; +} + +#endif + /* ------------------------------------------------------------------------- */ diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h new file mode 100644 index 00000000000..761a35276bb --- /dev/null +++ b/include/configs/TK885D.h @@ -0,0 +1,513 @@ +/* + * (C) Copyright 2000-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2006 + * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC885 1 /* This is a MPC885 CPU */ +#define CONFIG_TQM885D 1 /* ...on a TQM88D module */ +#define CONFIG_TK885D 1 /* ...in a TK885D base board */ + +#define CONFIG_8xx_OSCLK 10000000 /* 10 MHz - PLL input clock */ +#define CFG_8xx_CPUCLK_MIN 15000000 /* 15 MHz - CPU minimum clock */ +#define CFG_8xx_CPUCLK_MAX 133000000 /* 133 MHz - CPU maximum clock */ +#define CONFIG_8xx_CPUCLK_DEFAULT 66000000 /* 66 MHz - CPU default clock */ + /* (it will be used if there is no */ + /* 'cpuclk' variable with valid value) */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/TQM885D/uImage\0" \ + "kernel_addr=40080000\0" \ + "ramdisk_addr=40180000\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off 40000000 +${filesize};" \ + "erase 40000000 +${filesize};" \ + "cp.b 200000 40000000 ${filesize};" \ + "protect on 40000000 +${filesize}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ + +#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */ +#define CFG_I2C_SLAVE 0xFE + +#ifdef CONFIG_SOFT_I2C +/* + * Software (bit-bang) I2C driver configuration + */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + +#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 4 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +# define CONFIG_RTC_DS1337 1 +# define CFG_I2C_RTC_ADDR 0x68 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#undef CONFIG_RTC_MPC8xx /* MPC885 does not support RTC */ + +#define CONFIG_TIMESTAMP /* but print image timestmps */ + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING + + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0300000 /* 1 ... 3 MB in DRAM */ +#define CFG_ALT_MEMTEST /* alternate, more extensive + memory test.*/ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Enable loopw command. + */ +#define CONFIG_LOOPW + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ + +/* use CFI flash driver */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_USE_BUFFER_WRITE 1 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment */ +#define CFG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* + * FLASH timing: Default value of OR0 after reset + */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \ + OR_SCY_6_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) + +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM CFG_OR0_PRELIM +#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V ) + +/* + * BR2/3 and OR2/3 (SDRAM) + * + */ +#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */ +#define SDRAM_MAX_SIZE (256 << 20) /* max 256 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM ) +#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) + +#ifndef CONFIG_CAN_DRIVER +#define CFG_OR3_PRELIM CFG_OR2_PRELIM +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V ) +#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */ +#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */ +#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */ +#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI) +#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \ + BR_PS_8 | BR_MS_UPMB | BR_V ) +#endif /* CONFIG_CAN_DRIVER */ + +/* + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + */ +#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) + +/* + * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad) + * + * CPUclock(MHz) * 31.2 + * CFG_MAMR_PTA = ----------------------------------- with DFBRG = 0 + * 2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16 + * + * CPU clock = 15 MHz: CFG_MAMR_PTA = 29 -> 4 * 7.73 us + * CPU clock = 50 MHz: CFG_MAMR_PTA = 97 -> 4 * 7.76 us + * CPU clock = 66 MHz: CFG_MAMR_PTA = 128 -> 4 * 7.75 us + * CPU clock = 133 MHz: CFG_MAMR_PTA = 255 -> 4 * 7.67 us + * + * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will + * be met also in the default configuration, i.e. if environment variable + * 'cpuclk' is not set. + */ +#define CFG_MAMR_PTA 128 + +/* + * Memory Periodic Timer Prescaler Register (MPTPR) values. + */ +/* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 +/* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 10 column SDRAM */ +#define CFG_MAMR_10COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* + * Network configuration + */ +#define CONFIG_FEC_ENET /* enable ethernet on FEC */ +#define CONFIG_ETHER_ON_FEC1 /* ... for FEC1 */ +#define CONFIG_ETHER_ON_FEC2 /* ... for FEC2 */ + +#define CONFIG_LAST_STAGE_INIT 1 /* Have to configure PHYs for Linux */ + +/* CFG_DISCOVER_PHY only works with FEC if only one interface is enabled */ +#if (!defined(CONFIG_ETHER_ON_FEC1) || !defined(CONFIG_ETHER_ON_FEC2)) +#define CFG_DISCOVER_PHY +#endif + +#ifndef CFG_DISCOVER_PHY +/* PHY addresses - hard wired in hardware */ +#define CONFIG_FEC1_PHY 1 +#define CONFIG_FEC2_PHY 2 +#endif + +#define CONFIG_NET_RETRY_COUNT 3 +#define CONFIG_ETHPRIME "FEC ETHERNET" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 92fa37eac530860643afa26ae347af3d23d67309 Mon Sep 17 00:00:00 2001 From: Larry Johnson Date: Wed, 9 Jan 2008 12:42:35 -0500 Subject: Remove superfluous preprocessor conditionals from LM73 driver (1) Remove unused symbol "CFG_EEPROM_PAGE_WRITE_ENABLE". (2) Use conditional Makefile.o. Signed-off-by: Larry Johnson --- drivers/hwmon/Makefile | 2 +- drivers/hwmon/lm73.c | 9 --------- include/configs/korat.h | 1 - 3 files changed, 1 insertion(+), 11 deletions(-) (limited to 'include') diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 32e3f44a916..065433a6088 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -34,7 +34,7 @@ COBJS-y += adm1021.o COBJS-y += ds1621.o COBJS-y += ds1722.o COBJS-y += ds1775.o -COBJS-y += lm73.o +COBJS-$(CONFIG_DTT_LM73) += lm73.o COBJS-y += lm75.o COBJS-y += lm81.o diff --git a/drivers/hwmon/lm73.c b/drivers/hwmon/lm73.c index f9ae01297bc..db8ef662adc 100644 --- a/drivers/hwmon/lm73.c +++ b/drivers/hwmon/lm73.c @@ -31,13 +31,6 @@ */ #include - -#ifdef CONFIG_DTT_LM73 -#if !defined(CFG_EEPROM_PAGE_WRITE_ENABLE) || \ - (CFG_EEPROM_PAGE_WRITE_BITS < 1) -# error "CFG_EEPROM_PAGE_WRITE_ENABLE must be defined and CFG_EEPROM_PAGE_WRITE_BITS must be greater than 1 to use CONFIG_DTT_LM73" -#endif - #include #include @@ -177,5 +170,3 @@ int dtt_get_temp(int sensor) { return (dtt_read(sensor, DTT_READ_TEMP) + 0x0040) >> 7; } /* dtt_get_temp() */ - -#endif /* CONFIG_DTT_LM73 */ diff --git a/include/configs/korat.h b/include/configs/korat.h index 7d0640bbcf8..5182972829b 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -156,7 +156,6 @@ #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) #define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -- cgit v1.3.1 From 381e4e639720d8d2efb8066c7c48ec9588cb28c7 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 01:12:06 +0100 Subject: Added support for the mgsuvd board from keymile. Signed-off-by: Heiko Schocher --- MAKEALL | 1 + Makefile | 3 + board/mgsuvd/Makefile | 44 +++++++ board/mgsuvd/config.mk | 28 ++++ board/mgsuvd/mgsuvd.c | 216 +++++++++++++++++++++++++++++++ board/mgsuvd/u-boot.lds | 144 +++++++++++++++++++++ cpu/mpc8xx/cpu.c | 16 +++ include/commproc.h | 26 ++++ include/configs/mgsuvd.h | 325 +++++++++++++++++++++++++++++++++++++++++++++++ 9 files changed, 803 insertions(+) create mode 100644 board/mgsuvd/Makefile create mode 100644 board/mgsuvd/config.mk create mode 100644 board/mgsuvd/mgsuvd.c create mode 100644 board/mgsuvd/u-boot.lds create mode 100644 include/configs/mgsuvd.h (limited to 'include') diff --git a/MAKEALL b/MAKEALL index cb1322d7c93..8fbb7928baf 100755 --- a/MAKEALL +++ b/MAKEALL @@ -107,6 +107,7 @@ LIST_8xx=" \ lwmon \ MBX \ MBX860T \ + mgsuvd \ MHPC \ MPC86xADS \ MPC885ADS \ diff --git a/Makefile b/Makefile index fa12ed7cef8..60cc4e5afed 100644 --- a/Makefile +++ b/Makefile @@ -853,6 +853,9 @@ MBX_config \ MBX860T_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc8xx mbx8xx +mgsuvd_config: unconfig + @$(MKCONFIG) $(@:_config=) ppc mpc8xx mgsuvd + MHPC_config: unconfig @$(MKCONFIG) $(@:_config=) ppc mpc8xx mhpc eltec diff --git a/board/mgsuvd/Makefile b/board/mgsuvd/Makefile new file mode 100644 index 00000000000..af0d400c885 --- /dev/null +++ b/board/mgsuvd/Makefile @@ -0,0 +1,44 @@ +# +# (C) Copyright 2007 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS = $(BOARD).o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mgsuvd/config.mk b/board/mgsuvd/config.mk new file mode 100644 index 00000000000..8625cea5685 --- /dev/null +++ b/board/mgsuvd/config.mk @@ -0,0 +1,28 @@ +# +# (C) Copyright 2007 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mgsvud boards +# + +TEXT_BASE = 0xf0000000 diff --git a/board/mgsuvd/mgsuvd.c b/board/mgsuvd/mgsuvd.c new file mode 100644 index 00000000000..dd7d8236d57 --- /dev/null +++ b/board/mgsuvd/mgsuvd.c @@ -0,0 +1,216 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#if 0 +#define DEBUG +#endif + +#include +#include + +#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +const uint sdram_table[] = +{ + 0x0f07fc04, 0x0ffffc04, 0x00bdfc04, 0x0ff77c00, + 0x1ffffc05, 0xfffffc04, 0xfffffc04, 0xfffffc04, + /* 0x08 Burst Read */ + 0x0f07fc04, 0x0ffffc04, 0x00bdfc04, 0x00fffc00, + 0x00fffc00, 0x00fffc00, 0x0ff77c00, 0x1ffffc05, + /* 0x10 Load mode register */ + 0x0ffffc34, 0x0ff57c04, 0x0ffffc04, 0x1ffffc05, + 0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04, + /* 0x18 Single Write */ + 0x0f07fc04, 0x0ffffc00, 0x00bd7c04, 0x0ffffc04, + 0x0ff77c04, 0x1ffffc05, 0xfffffc04, 0xfffffc04, + /* 0x20 Burst Write */ + 0x0f07fc04, 0x0ffffc00, 0x00bd7c00, 0x00fffc00, + 0x00fffc00, 0x00fffc04, 0x0ffffc04, 0x0ff77c04, + 0x1ffffc05, 0xfffffc04, 0xfffffc04, 0xfffffc04, + 0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04, + /* 0x30 Precharge all and Refresh */ + 0x0ff77c04, 0x0ffffc04, 0x0ff5fc84, 0x0ffffc04, + 0x0ffffc04, 0x0ffffc84, 0x1ffffc05, 0xfffffc04, + 0xfffffc04, 0xfffffc04, 0xfffffc04, 0xfffffc04, + /* 0x3C Exception */ + 0x7ffffc04, 0xfffffc07, 0xfffffc04, 0xfffffc04, +}; + +int checkboard (void) +{ + puts ("Board: Keymile mgsuvd\n"); + return (0); +} + +long int initdram (int board_type) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile memctl8xx_t *memctl = &immap->im_memctl; + long int size; + + upmconfig (UPMB, (uint *) sdram_table, + sizeof (sdram_table) / sizeof (uint)); + + /* + * Preliminary prescaler for refresh (depends on number of + * banks): This value is selected for four cycles every 62.4 us + * with two SDRAM banks or four cycles every 31.2 us with one + * bank. It will be adjusted after memory sizing. + */ + memctl->memc_mptpr = CFG_MPTPR; + + /* + * The following value is used as an address (i.e. opcode) for + * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If + * the port size is 32bit the SDRAM does NOT "see" the lower two + * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for + * MICRON SDRAMs: + * -> 0 00 010 0 010 + * | | | | +- Burst Length = 4 + * | | | +----- Burst Type = Sequential + * | | +------- CAS Latency = 2 + * | +----------- Operating Mode = Standard + * +-------------- Write Burst Mode = Programmed Burst Length + */ + memctl->memc_mar = CFG_MAR; + + /* + * Map controller banks 1 to the SDRAM banks 1 at + * preliminary addresses - these have to be modified after the + * SDRAM size has been determined. + */ + memctl->memc_or1 = CFG_OR1_PRELIM; + memctl->memc_br1 = CFG_BR1_PRELIM; + + memctl->memc_mbmr = CFG_MBMR & (~(MBMR_PTBE)); /* no refresh yet */ + + udelay (200); + + /* perform SDRAM initializsation sequence */ + + memctl->memc_mcr = 0x80802830; /* SDRAM bank 0 */ + udelay (1); + memctl->memc_mcr = 0x80802110; /* SDRAM bank 0 - execute twice */ + udelay (1); + + memctl->memc_mbmr |= MBMR_PTBE; /* enable refresh */ + + udelay (1000); + + /* + * Check Bank 0 Memory Size for re-configuration + * + */ + size = get_ram_size(SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE); + + udelay (1000); + + debug ("SDRAM Bank 0: %ld MB\n", size >> 20); + + return (size); +} + +#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) +/* + * update "memory" property in the blob + */ +void ft_blob_update(void *blob, bd_t *bd) +{ + int ret, nodeoffset = 0; + ulong brg_data[1] = {0}; + ulong memory_data[2] = {0}; + ulong flash_data[4] = {0}; + + memory_data[0] = cpu_to_be32(bd->bi_memstart); + memory_data[1] = cpu_to_be32(bd->bi_memsize); + + nodeoffset = fdt_path_offset (blob, "/memory"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "reg", memory_data, + sizeof(memory_data)); + if (ret < 0) + printf("ft_blob_update): cannot set /memory/reg " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /memory node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + + flash_data[2] = cpu_to_be32(bd->bi_flashstart); + flash_data[3] = cpu_to_be32(bd->bi_flashsize); + nodeoffset = fdt_path_offset (blob, "/localbus"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "ranges", flash_data, + sizeof(flash_data)); + if (ret < 0) + printf("ft_blob_update): cannot set /localbus/ranges " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /localbus node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + /* BRG */ + brg_data[0] = cpu_to_be32(bd->bi_busfreq); + nodeoffset = fdt_path_offset (blob, "/soc866/cpm"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "brg-frequency", brg_data, + sizeof(brg_data)); + if (ret < 0) + printf("ft_blob_update): cannot set /soc866/cpm/brg-frequency " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /localbus node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + /* MAC Adresse */ + nodeoffset = fdt_path_offset (blob, "/soc866/cpm/scc"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "mac-address", bd->bi_enetaddr, + sizeof(uchar) * 6); + if (ret < 0) + printf("ft_blob_update): cannot set /soc866/cpm/scc/mac-address " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /localbus node " + "err:%s\n", fdt_strerror(nodeoffset)); + } +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup( blob, bd); + ft_blob_update(blob, bd); +} +#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */ diff --git a/board/mgsuvd/u-boot.lds b/board/mgsuvd/u-boot.lds new file mode 100644 index 00000000000..d526d1d07d3 --- /dev/null +++ b/board/mgsuvd/u-boot.lds @@ -0,0 +1,144 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + /* WARNING - the following is hand-optimized to fit within */ + /* the sector layout of our flash chips! XXX FIXME XXX */ + + cpu/mpc8xx/start.o (.text) + cpu/mpc8xx/traps.o (.text) + common/dlmalloc.o (.text) + lib_ppc/ppcstring.o (.text) + lib_generic/vsprintf.o (.text) + lib_generic/crc32.o (.text) + lib_generic/zlib.o (.text) + lib_ppc/cache.o (.text) + lib_ppc/time.o (.text) + + . = DEFINED(env_offset) ? env_offset : .; + common/environment.o (.ppcenv) + + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; + __fixup_entries = (. - _FIXUP_TABLE_)>>2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/cpu/mpc8xx/cpu.c b/cpu/mpc8xx/cpu.c index 97112f03daf..c8783525129 100644 --- a/cpu/mpc8xx/cpu.c +++ b/cpu/mpc8xx/cpu.c @@ -39,6 +39,12 @@ #include #include +#if defined(CONFIG_OF_LIBFDT) +#include +#include +#include +#endif + DECLARE_GLOBAL_DATA_PTR; static char *cpu_warning = "\n " \ @@ -632,3 +638,13 @@ void reset_8xx_watchdog (volatile immap_t * immr) #endif /* CONFIG_WATCHDOG */ /* ------------------------------------------------------------------------- */ +#if defined(CONFIG_OF_LIBFDT) +void ft_cpu_setup (void *blob, bd_t *bd) +{ + char * cpu_path = "/cpus/" OF_CPU; + + do_fixup_by_path_u32(blob, cpu_path, "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", OF_TBCLK, 1); + do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); +} +#endif /* CONFIG_OF_LIBFDT */ diff --git a/include/commproc.h b/include/commproc.h index 12400e3eddb..53659c28fd9 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -1120,6 +1120,32 @@ typedef struct scc_enet { #define SICR_ENET_CLKRT ((uint)0x0000003d) #endif /* CONFIG_MBX */ +/*** MGSUVD *********************************************************/ + +/* The MGSUVD Service Module uses SCC3 for Ethernet */ + +#ifdef CONFIG_MGSUVD +#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */ +#define CPM_CR_ENET CPM_CR_CH_SCC3 +#define SCC_ENET 2 +#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */ +#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */ +#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */ +#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */ + +#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */ + +#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */ +#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */ + +/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to + * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero. + */ +#define SICR_ENET_MASK ((uint)0x00FF0000) +#define SICR_ENET_CLKRT ((uint)0x00250000) +#endif /* CONFIG_MGSUVD */ + + /*** MHPC ********************************************************/ #if defined(CONFIG_MHPC) diff --git a/include/configs/mgsuvd.h b/include/configs/mgsuvd.h new file mode 100644 index 00000000000..13e7a7c07b4 --- /dev/null +++ b/include/configs/mgsuvd.h @@ -0,0 +1,325 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC866 1 /* This is a MPC866 CPU */ +#define CONFIG_MGSUVD 1 /* ...on a mgsuvd board */ + +#define CONFIG_8xx_GCLK_FREQ 66000000 + +#define CFG_SMC_UCODE_PATCH 1 /* Relocate SMC1 */ +#define CFG_SMC_DPMEM_OFFSET 0x1fc0 +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "addcon=setenv bootargs ${bootargs} console=ttyCPM0,${baudrate}\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcon;"\ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/mgsuvd/uImage\0" \ + "fdt_addr=400000\0" \ + "kernel_addr=200000\0" \ + "fdt_file=/tftpboot/mgsuvd/mgsuvd.dtb\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off f0000000 +${filesize};" \ + "erase f0000000 +${filesize};" \ + "cp.b 200000 f0000000 ${filesize};" \ + "protect on f0000000 +${filesize}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + +#undef CONFIG_RTC_MPC8xx /* MPC866 does not support RTC */ + +#define CONFIG_TIMESTAMP /* but print image timestmps */ + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xf0000000 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_FLASH_SIZE 32 +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ + + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x08000 /* Total Size of Environment Sector */ +#define CFG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#define CFG_SYPCR 0xffffff89 + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + */ +#define CFG_SIUMCR 0x00610480 + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK 0x01800000 +#define CFG_SCCR 0x01800000 + +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xf0000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* + * FLASH timing: Default value of OR0 after reset + */ +#define CFG_OR0_PRELIM 0xfe000954 +#define CFG_BR0_PRELIM 0xf0000401 + +/* + * BR1 and OR1 (SDRAM) + * + */ +#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE (64 << 20) /* max 64 MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM 0x00000A00 + +#define CFG_OR1_PRELIM 0xfc000800 +#define CFG_BR1_PRELIM (0x000000C0 | 0x01) + +#define CFG_MPTPR 0x0200 +/* PTB=16, AMB=001, FIXME 1 RAS precharge cycles, 1 READ loop cycle (not used), + 1 Write loop Cycle (not used), 1 Timer Loop Cycle */ +#define CFG_MBMR 0x10964111 +#define CFG_MAR 0x00000088 + +/* + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + */ +#define CFG_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64)) +/* HS HS noch zu setzen */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_SCC3_ENET +#define CONFIG_ETHPRIME "SCC ETHERNET" +#define CONFIG_HAS_ETH0 + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,866@0" +#define OF_SOC "soc@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc/cpm/serial@a80" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From b423d055cc2e13c4ef1f0389c3fa2988d0eed818 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 01:12:07 +0100 Subject: Enable SMC microcode relocation patch for SMC1. Signed-off-by: Heiko Schocher --- README | 4 +++ cpu/mpc8xx/cpu_init.c | 6 ++-- cpu/mpc8xx/serial.c | 21 ++++++++++++ cpu/mpc8xx/upatch.c | 94 ++++++++++++++++++++++++++++++++++++++++++++++++++- include/commproc.h | 2 ++ 5 files changed, 124 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/README b/README index 57fc01a9096..f2a49149238 100644 --- a/README +++ b/README @@ -2278,6 +2278,10 @@ Low Level (hardware related) configuration options: enable I2C microcode relocation patch (MPC8xx); define relocation offset in DPRAM [DSP2] +- CFG_SMC_UCODE_PATCH, CFG_SMC_DPMEM_OFFSET [0x1FC0]: + enable SMC microcode relocation patch (MPC8xx); + define relocation offset in DPRAM [SMC1] + - CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]: enable SPI microcode relocation patch (MPC8xx); define relocation offset in DPRAM [SCC4] diff --git a/cpu/mpc8xx/cpu_init.c b/cpu/mpc8xx/cpu_init.c index c79e5780ad3..fb3414aae25 100644 --- a/cpu/mpc8xx/cpu_init.c +++ b/cpu/mpc8xx/cpu_init.c @@ -31,7 +31,8 @@ DECLARE_GLOBAL_DATA_PTR; #endif -#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) +#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) || \ + defined(CFG_SMC_UCODE_PATCH) void cpm_load_patch (volatile immap_t * immr); #endif @@ -253,7 +254,8 @@ void cpu_init_f (volatile immap_t * immr) immr->im_cpm.cp_rccr = CFG_RCCR; #endif -#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) +#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) || \ + defined(CFG_SMC_UCODE_PATCH) cpm_load_patch (immr); /* load mpc8xx microcode patch */ #endif } diff --git a/cpu/mpc8xx/serial.c b/cpu/mpc8xx/serial.c index 68804cc4394..ad0229999fa 100644 --- a/cpu/mpc8xx/serial.c +++ b/cpu/mpc8xx/serial.c @@ -124,6 +124,12 @@ static int smc_init (void) sp = (smc_t *) &(cp->cp_smc[SMC_INDEX]); up = (smc_uart_t *) &cp->cp_dparam[PROFF_SMC]; +#ifdef CFG_SMC_UCODE_PATCH + up = (smc_uart_t *) &cp->cp_dpmem[up->smc_rpbase]; +#else + /* Disable relocation */ + up->smc_rpbase = 0; +#endif /* Disable transmitter/receiver. */ @@ -212,6 +218,12 @@ static int smc_init (void) up->smc_tbase = dpaddr+sizeof(cbd_t); up->smc_rfcr = SMC_EB; up->smc_tfcr = SMC_EB; +#if defined (CFG_SMC_UCODE_PATCH) + up->smc_rbptr = up->smc_rbase; + up->smc_tbptr = up->smc_tbase; + up->smc_rstate = 0; + up->smc_tstate = 0; +#endif #if defined(CONFIG_MBX) board_serial_init(); @@ -288,6 +300,9 @@ smc_putc(const char c) smc_putc ('\r'); up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC]; +#ifdef CFG_SMC_UCODE_PATCH + up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase]; +#endif tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase]; @@ -326,6 +341,9 @@ smc_getc(void) unsigned char c; up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC]; +#ifdef CFG_SMC_UCODE_PATCH + up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase]; +#endif rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase]; @@ -351,6 +369,9 @@ smc_tstc(void) volatile cpm8xx_t *cpmp = &(im->im_cpm); up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC]; +#ifdef CFG_SMC_UCODE_PATCH + up = (smc_uart_t *) &cpmp->cp_dpmem[up->smc_rpbase]; +#endif rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase]; diff --git a/cpu/mpc8xx/upatch.c b/cpu/mpc8xx/upatch.c index eccff645e30..4d6c5224679 100644 --- a/cpu/mpc8xx/upatch.c +++ b/cpu/mpc8xx/upatch.c @@ -1,7 +1,8 @@ #include #include -#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) +#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH) || \ + defined(CFG_SMC_UCODE_PATCH) static void UcodeCopy (volatile cpm8xx_t *cpm); @@ -32,13 +33,29 @@ void cpm_load_patch (volatile immap_t *immr) } #endif +#ifdef CFG_SMC_UCODE_PATCH + { + volatile smc_uart_t *up = (smc_uart_t *) & immr->im_cpm.cp_dparam[PROFF_SMC1]; + /* Activate the microcode per the instructions in the microcode manual */ + /* NOTE: We're only relocating the SMC parameters. */ + immr->im_cpm.cp_cpmcr1 = 0x8080; /* Write Trap register 1 value */ + immr->im_cpm.cp_cpmcr2 = 0x8088; /* Write Trap register 2 value */ + up->smc_rpbase = CFG_SMC_DPMEM_OFFSET; /* Where to relocte SMC params */ + } +#endif + /* * Enable DPRAM microcode to execute from the first 512 bytes * and a 256 byte extension of DPRAM. */ +#ifdef CFG_SMC_UCODE_PATCH + immr->im_cpm.cp_rccr |= 0x0002; +#else immr->im_cpm.cp_rccr |= 0x0001; +#endif } +#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCh) static ulong patch_2000[] = { 0x7FFFEFD9, 0x3FFD0000, 0x7FFB49F7, 0x7FF90000, 0x5FEFADF7, 0x5F88ADF7, 0x5FEFAFF7, 0x5F88AFF7, @@ -82,6 +99,81 @@ static ulong patch_2F00[] = { 0x35931497, 0x35376956, 0xBD697B9D, 0x96931313, 0x19797937, 0x69350000, }; +#else + +static ulong patch_2000[] = { + 0x3fff0000, 0x3ffd0000, 0x3ffb0000, 0x3ff90000, + 0x5fefeff8, 0x5f91eff8, 0x3ff30000, 0x3ff10000, + 0x3a11e710, 0xedf0ccb9, 0xf318ed66, 0x7f0e5fe2, + 0x7fedbb38, 0x3afe7468, 0x7fedf4d8, 0x8ffbb92d, + 0xb83b77fd, 0xb0bb5eb9, 0xdfda7fed, 0x90bde74d, + 0x6f0dcbd3, 0xe7decfed, 0xcb50cfed, 0xcfeddf6d, + 0x914d4f74, 0x5eaedfcb, 0x9ee0e7df, 0xefbb6ffb, + 0xe7ef7f0e, 0x9ee57fed, 0xebb7effa, 0xeb30affb, + 0x7fea90b3, 0x7e0cf09f, 0xbffff318, 0x5fffdfff, + 0xac35efea, 0x7fce1fc1, 0xe2ff5fbd, 0xaffbe2ff, + 0x5fbfaffb, 0xf9a87d0f, 0xaef8770f, 0x7d0fb0a2, + 0xeffbbfff, 0xcfef5fba, 0x7d0fbfff, 0x5fba4cf8, + 0x7fddd09b, 0x49f847fd, 0x7efdf097, 0x7fedfffd, + 0x7dfdf093, 0xef7e7e1e, 0x5fba7f0e, 0x3a11e710, + 0xedf0cc87, 0xfb18ad0a, 0x1f85bbb8, 0x74283b7e, + 0x7375e4bb, 0x2ab64fb8, 0x5c7de4bb, 0x32fdffbf, + 0x5f0843f8, 0x7ce3e1bb, 0xe74f7ded, 0x6f0f4fe8, + 0xc7ba32be, 0x73f2efeb, 0x600b4f78, 0xe5bb760b, + 0x5388aef8, 0x4ef80b6a, 0xcfef9ee5, 0xabf8751f, + 0xefef5b88, 0x741f4fe8, 0x751e760d, 0x7fdb70dd, + 0x741cafce, 0xefcc7fce, 0x751e7088, 0x741ce7bb, + 0x334ecfed, 0xafdbefeb, 0xe5bb760b, 0x53ceaef8, + 0xafe8e7eb, 0x4bf8771e, 0x7e007fed, 0x4fcbe2cc, + 0x7fbc3085, 0x7b0f7a0f, 0x34b177fd, 0xb0e75e93, + 0xdf313e3b, 0xaf78741f, 0x741f30cc, 0xcfef5f08, + 0x741f3e88, 0xafb8771e, 0x5f437fed, 0x0bafe2cc, + 0x741ccfec, 0xe5ca53a9, 0x6fcb4f74, 0x5e89df27, + 0x2a923d14, 0x4b8fdf0c, 0x751f741c, 0x6c1eeffa, + 0xefea7fce, 0x6ffc309a, 0xefec3fca, 0x308fdf0a, + 0xadf85e7a, 0xaf7daefd, 0x5e7adf0a, 0x5e7aafdd, + 0x761f1088, 0x1e7c7efd, 0x3089fffe, 0x4908fb18, + 0x5fffdfff, 0xafbbf0f7, 0x4ef85f43, 0xadf81489, + 0x7a0f7089, 0xcfef5089, 0x7a0fdf0c, 0x5e7cafed, + 0xbc6e780f, 0xefef780f, 0xefef790f, 0xa7f85eeb, + 0xffef790f, 0xefef790f, 0x1489df0a, 0x5e7aadfd, + 0x5f09fffb, 0xe79aded9, 0xeff96079, 0x607ae79a, + 0xded8eff9, 0x60795edb, 0x607acfef, 0xefefefdf, + 0xefbfef7f, 0xeeffedff, 0xebffe7ff, 0xafefafdf, + 0xafbfaf7f, 0xaeffadff, 0xabffa7ff, 0x6fef6fdf, + 0x6fbf6f7f, 0x6eff6dff, 0x6bff67ff, 0x2fef2fdf, + 0x2fbf2f7f, 0x2eff2dff, 0x2bff27ff, 0x4e08fd1f, + 0xe5ff6e0f, 0xaff87eef, 0x7e0ffdef, 0xf11f6079, + 0xabf8f51e, 0x7e0af11c, 0x37cfae16, 0x7fec909a, + 0xadf8efdc, 0xcfeae52f, 0x7d0fe12b, 0xf11c6079, + 0x7e0a4df8, 0xcfea5ea0, 0x7d0befec, 0xcfea5ea2, + 0xe522efdc, 0x5ea2cfda, 0x4e08fd1f, 0x6e0faff8, + 0x7c1f761f, 0xfdeff91f, 0x6079abf8, 0x761cee00, + 0xf91f2bfb, 0xefefcfec, 0xf91f6079, 0x761c27fb, + 0xefdf5e83, 0xcfdc7fdd, 0x50f84bf8, 0x47fd7c1f, + 0x761ccfcf, 0x7eef7fed, 0x7dfd70ef, 0xef7e7f1e, + 0x771efb18, 0x6079e722, 0xe6bbe5bb, 0x2e66e5bb, + 0x600b2ee1, 0xe2bbe2bb, 0xe2bbe2bb, 0x2f5ee2bb, + 0xe2bb2ff9, 0x6079e2bb, +}; + +static ulong patch_2F00[] = { + 0x30303030, 0x3e3e3030, 0xaf79b9b3, 0xbaa3b979, + 0x9693369f, 0x79f79777, 0x97333fff, 0xfb3b9e9f, + 0x79b91d11, 0x9e13f3ff, 0x3f9b6bd9, 0xe173d136, + 0x695669d1, 0x697b3daf, 0x79b93a3a, 0x3f979f91, + 0x379ff976, 0xf99777fd, 0x9779737d, 0xe9d6bbf9, + 0xbfffd9df, 0x97f7fd97, 0x6f7b9bff, 0xf9bd9683, + 0x397db973, 0xd97b3b9f, 0xd7f9f733, 0x9993bb9e, + 0xe1f9ef93, 0x73773337, 0xb936917d, 0x11f87379, + 0xb979d336, 0x8b7ded73, 0x1b7d9337, 0x31f3f22f, + 0x3f2327ee, 0xeeeeeeee, 0xeeeeeeee, 0xeeeeeeee, + 0xeeeeee4b, 0xf4fbdbd2, 0x58bb1878, 0x577fdfd2, + 0xd573b773, 0xf7374b4f, 0xbdbd25b8, 0xb177d2d1, + 0x7376856b, 0xbfdd687b, 0xdd2fff8f, 0x78ffff8f, + 0xf22f0000, +}; +#endif static void UcodeCopy (volatile cpm8xx_t *cpm) { diff --git a/include/commproc.h b/include/commproc.h index 53659c28fd9..6b1b4e8fffb 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -159,6 +159,8 @@ typedef struct smc_uart { ushort smc_brkec; /* rcv'd break condition counter */ ushort smc_brkcr; /* xmt break count register */ ushort smc_rmask; /* Temporary bit mask */ + u_char res1[8]; + ushort smc_rpbase; /* Relocation pointer */ } smc_uart_t; /* Function code bits. -- cgit v1.3.1 From ac9db066b26935f31bff15c98168b19faeb603f3 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 01:12:08 +0100 Subject: Added support for the mgcoge board from keymile. Signed-off-by: Heiko Schocher --- MAKEALL | 1 + Makefile | 3 + board/mgcoge/Makefile | 50 +++++++ board/mgcoge/config.mk | 24 ++++ board/mgcoge/mgcoge.c | 345 +++++++++++++++++++++++++++++++++++++++++++++++ cpu/mpc8260/ether_scc.c | 9 +- include/configs/mgcoge.h | 317 +++++++++++++++++++++++++++++++++++++++++++ 7 files changed, 745 insertions(+), 4 deletions(-) create mode 100644 board/mgcoge/Makefile create mode 100644 board/mgcoge/config.mk create mode 100644 board/mgcoge/mgcoge.c create mode 100644 include/configs/mgcoge.h (limited to 'include') diff --git a/MAKEALL b/MAKEALL index 8fbb7928baf..67fadd01406 100755 --- a/MAKEALL +++ b/MAKEALL @@ -282,6 +282,7 @@ LIST_8260=" \ hymod \ IPHASE4539 \ ISPAN \ + mgcoge \ MPC8260ADS \ MPC8266ADS \ MPC8272ADS \ diff --git a/Makefile b/Makefile index 60cc4e5afed..0288fa1f737 100644 --- a/Makefile +++ b/Makefile @@ -1547,6 +1547,9 @@ ISPAN_REVB_config: unconfig fi @$(MKCONFIG) -a ISPAN ppc mpc8260 ispan +mgcoge_config : unconfig + @$(MKCONFIG) mgcoge ppc mpc8260 mgcoge + MPC8260ADS_config \ MPC8260ADS_lowboot_config \ MPC8260ADS_33MHz_config \ diff --git a/board/mgcoge/Makefile b/board/mgcoge/Makefile new file mode 100644 index 00000000000..1a1424406f1 --- /dev/null +++ b/board/mgcoge/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2001-2007 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mgcoge/config.mk b/board/mgcoge/config.mk new file mode 100644 index 00000000000..143bc9f76c1 --- /dev/null +++ b/board/mgcoge/config.mk @@ -0,0 +1,24 @@ +# +# (C) Copyright 2007 +# Heiko Schocher, DENX Software Engineering, hs@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +TEXT_BASE = 0xFE000000 diff --git a/board/mgcoge/mgcoge.c b/board/mgcoge/mgcoge.c new file mode 100644 index 00000000000..0207a3aebd7 --- /dev/null +++ b/board/mgcoge/mgcoge.c @@ -0,0 +1,345 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) +#include +#endif + +/* + * I/O Port configuration table + * + * if conf is 1, then that port pin will be configured at boot time + * according to the five values podr/pdir/ppar/psor/pdat for that entry + */ +const iop_conf_t iop_conf_tab[4][32] = { + + /* Port A */ + { /* conf ppar psor pdir podr pdat */ + /* PA31 */ { 0, 0, 0, 0, 0, 0 }, /* PA31 */ + /* PA30 */ { 0, 0, 0, 0, 0, 0 }, /* PA30 */ + /* PA29 */ { 0, 0, 0, 0, 0, 0 }, /* PA29 */ + /* PA28 */ { 0, 0, 0, 0, 0, 0 }, /* PA28 */ + /* PA27 */ { 0, 0, 0, 0, 0, 0 }, /* PA27 */ + /* PA26 */ { 0, 0, 0, 0, 0, 0 }, /* PA26 */ + /* PA25 */ { 0, 0, 0, 0, 0, 0 }, /* PA25 */ + /* PA24 */ { 0, 0, 0, 0, 0, 0 }, /* PA24 */ + /* PA23 */ { 0, 0, 0, 0, 0, 0 }, /* PA23 */ + /* PA22 */ { 0, 0, 0, 0, 0, 0 }, /* PA22 */ + /* PA21 */ { 0, 0, 0, 0, 0, 0 }, /* PA21 */ + /* PA20 */ { 0, 0, 0, 0, 0, 0 }, /* PA20 */ + /* PA19 */ { 0, 0, 0, 0, 0, 0 }, /* PA19 */ + /* PA18 */ { 0, 0, 0, 0, 0, 0 }, /* PA18 */ + /* PA17 */ { 0, 0, 0, 0, 0, 0 }, /* PA17 */ + /* PA16 */ { 0, 0, 0, 0, 0, 0 }, /* PA16 */ + /* PA15 */ { 0, 0, 0, 0, 0, 0 }, /* PA15 */ + /* PA14 */ { 0, 0, 0, 0, 0, 0 }, /* PA14 */ + /* PA13 */ { 0, 0, 0, 0, 0, 0 }, /* PA13 */ + /* PA12 */ { 0, 0, 0, 0, 0, 0 }, /* PA12 */ + /* PA11 */ { 0, 0, 0, 0, 0, 0 }, /* PA11 */ + /* PA10 */ { 0, 0, 0, 0, 0, 0 }, /* PA10 */ + /* PA9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TxD */ + /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RxD */ + /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */ + /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */ + /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */ + /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */ + /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */ + /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */ + /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */ + /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */ + }, + + /* Port B */ + { /* conf ppar psor pdir podr pdat */ + /* PB31 */ { 0, 0, 0, 0, 0, 0 }, /* PB31 */ + /* PB30 */ { 0, 0, 0, 0, 0, 0 }, /* PB30 */ + /* PB29 */ { 0, 0, 0, 0, 0, 0 }, /* PB29 */ + /* PB28 */ { 0, 0, 0, 0, 0, 0 }, /* PB28 */ + /* PB27 */ { 0, 0, 0, 0, 0, 0 }, /* PB27 */ + /* PB26 */ { 0, 0, 0, 0, 0, 0 }, /* PB26 */ + /* PB25 */ { 0, 0, 0, 0, 0, 0 }, /* PB25 */ + /* PB24 */ { 0, 0, 0, 0, 0, 0 }, /* PB24 */ + /* PB23 */ { 0, 0, 0, 0, 0, 0 }, /* PB23 */ + /* PB22 */ { 0, 0, 0, 0, 0, 0 }, /* PB22 */ + /* PB21 */ { 0, 0, 0, 0, 0, 0 }, /* PB21 */ + /* PB20 */ { 0, 0, 0, 0, 0, 0 }, /* PB20 */ + /* PB19 */ { 0, 0, 0, 0, 0, 0 }, /* PB19 */ + /* PB18 */ { 0, 0, 0, 0, 0, 0 }, /* PB18 */ + /* PB17 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB16 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB15 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB14 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB13 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB12 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB11 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB10 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB9 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB8 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB6 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB5 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB4 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */ + }, + + /* Port C */ + { /* conf ppar psor pdir podr pdat */ + /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */ + /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */ + /* PC29 */ { 0, 0, 0, 0, 0, 0 }, /* PC29 */ + /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */ + /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */ + /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */ + /* PC25 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4 RxClk */ + /* PC24 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4 TxClk */ + /* PC23 */ { 0, 0, 0, 0, 0, 0 }, /* PC23 */ + /* PC22 */ { 0, 0, 0, 0, 0, 0 }, /* PC22 */ + /* PC21 */ { 0, 0, 0, 0, 0, 0 }, /* PC21 */ + /* PC20 */ { 0, 0, 0, 0, 0, 0 }, /* PC20 */ + /* PC19 */ { 0, 0, 0, 0, 0, 0 }, /* PC19 */ + /* PC18 */ { 0, 0, 0, 0, 0, 0 }, /* PC18 */ + /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */ + /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */ + /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */ + /* PC14 */ { 0, 0, 0, 0, 0, 0 }, /* PC14 */ + /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */ + /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */ + /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */ + /* PC10 */ { 0, 0, 0, 0, 0, 0 }, /* PC10 */ + /* PC9 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4: CTS */ + /* PC8 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4: CD */ + /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */ + /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */ + /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */ + /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */ + /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */ + /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */ + /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */ + /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */ + }, + + /* Port D */ + { /* conf ppar psor pdir podr pdat */ + /* PD31 */ { 0, 0, 0, 0, 0, 0 }, /* PD31 */ + /* PD30 */ { 0, 0, 0, 0, 0, 0 }, /* PD30 */ + /* PD29 */ { 0, 0, 0, 0, 0, 0 }, /* PD29 */ + /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */ + /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */ + /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */ + /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */ + /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */ + /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */ + /* PD22 */ { 1, 1, 0, 0, 0, 0 }, /* SCC4: RXD */ + /* PD21 */ { 1, 1, 0, 1, 0, 0 }, /* SCC4: TXD */ + /* PD20 */ { 1, 1, 0, 1, 0, 0 }, /* SCC4: RTS */ + /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */ + /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */ + /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ + /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ + /* PD15 */ { 0, 0, 0, 0, 0, 0 }, /* PD15 */ + /* PD14 */ { 0, 0, 0, 0, 0, 0 }, /* PD14 */ + /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ + /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ + /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ + /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ + /* PD9 */ { 0, 0, 0, 0, 0, 0 }, /* PD9 */ + /* PD8 */ { 0, 0, 0, 0, 0, 0 }, /* PD8 */ + /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */ + /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */ + /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */ + /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */ + /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* non-existent */ + /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* non-existent */ + } +}; + +/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx + * + * This routine performs standard 8260 initialization sequence + * and calculates the available memory size. It may be called + * several times to try different SDRAM configurations on both + * 60x and local buses. + */ +static long int try_init (volatile memctl8260_t * memctl, ulong sdmr, + ulong orx, volatile uchar * base) +{ + volatile uchar c = 0xff; + volatile uint *sdmr_ptr; + volatile uint *orx_ptr; + ulong maxsize, size; + int i; + + /* We must be able to test a location outsize the maximum legal size + * to find out THAT we are outside; but this address still has to be + * mapped by the controller. That means, that the initial mapping has + * to be (at least) twice as large as the maximum expected size. + */ + maxsize = (1 + (~orx | 0x7fff))/* / 2*/; + + sdmr_ptr = &memctl->memc_psdmr; + orx_ptr = &memctl->memc_or1; + + *orx_ptr = orx; + + /* + * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): + * + * "At system reset, initialization software must set up the + * programmable parameters in the memory controller banks registers + * (ORx, BRx, P/LSDMR). After all memory parameters are configured, + * system software should execute the following initialization sequence + * for each SDRAM device. + * + * 1. Issue a PRECHARGE-ALL-BANKS command + * 2. Issue eight CBR REFRESH commands + * 3. Issue a MODE-SET command to initialize the mode register + * + * The initial commands are executed by setting P/LSDMR[OP] and + * accessing the SDRAM with a single-byte transaction." + * + * The appropriate BRx/ORx registers have already been set when we + * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE. + */ + + *sdmr_ptr = sdmr | PSDMR_OP_PREA; + *base = c; + + *sdmr_ptr = sdmr | PSDMR_OP_CBRR; + for (i = 0; i < 8; i++) + *base = c; + + *sdmr_ptr = sdmr | PSDMR_OP_MRW; + *(base + CFG_MRS_OFFS) = c; /* setting MR on address lines */ + + *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN; + *base = c; + + size = get_ram_size((long *)base, maxsize); + *orx_ptr = orx | ~(size - 1); + + return (size); +} + +long int initdram(int board_type) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile memctl8260_t *memctl = &immap->im_memctl; + + long psize; + + memctl->memc_psrt = CFG_PSRT; + memctl->memc_mptpr = CFG_MPTPR; + +#ifndef CFG_RAMBOOT + /* 60x SDRAM setup: + */ + psize = try_init (memctl, CFG_PSDMR, CFG_OR1, + (uchar *) CFG_SDRAM_BASE); +#endif /* CFG_RAMBOOT */ + + icache_enable (); + + return (psize); +} + +int checkboard(void) +{ + puts("Board: mgcoge\n"); + + return 0; +} + +#if defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) +/* + * update "memory" property in the blob + */ +void ft_blob_update(void *blob, bd_t *bd) +{ + int ret, nodeoffset = 0; + ulong memory_data[2] = {0}; + ulong flash_data[4] = {0}; + + memory_data[0] = cpu_to_be32(bd->bi_memstart); + memory_data[1] = cpu_to_be32(bd->bi_memsize); + + nodeoffset = fdt_path_offset (blob, "/memory"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "reg", memory_data, + sizeof(memory_data)); + if (ret < 0) + printf("ft_blob_update): cannot set /memory/reg " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /memory node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + /* update Flash size */ + flash_data[2] = cpu_to_be32(bd->bi_flashstart); + flash_data[3] = cpu_to_be32(bd->bi_flashsize); + nodeoffset = fdt_path_offset (blob, "/localbus"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "ranges", flash_data, + sizeof(flash_data)); + if (ret < 0) + printf("ft_blob_update): cannot set /localbus/ranges " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /localbus node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + /* MAC Adresse */ + nodeoffset = fdt_path_offset (blob, "/soc/cpm/ethernet"); + if (nodeoffset >= 0) { + ret = fdt_setprop(blob, nodeoffset, "mac-address", bd->bi_enetaddr, + sizeof(uchar) * 6); + if (ret < 0) + printf("ft_blob_update): cannot set /soc/cpm/ethernet/mac-address " + "property err:%s\n", fdt_strerror(ret)); + } + else { + /* memory node is required in dts */ + printf("ft_blob_update(): cannot find /localbus node " + "err:%s\n", fdt_strerror(nodeoffset)); + } + +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup( blob, bd); + ft_blob_update(blob, bd); +} +#endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */ diff --git a/cpu/mpc8260/ether_scc.c b/cpu/mpc8260/ether_scc.c index e56839d3aad..633d053914e 100644 --- a/cpu/mpc8260/ether_scc.c +++ b/cpu/mpc8260/ether_scc.c @@ -77,7 +77,9 @@ #define TX_BUF_CNT 2 -#define TOUT_LOOP 1000000 +#if !defined(CFG_SCC_TOUT_LOOP) + #define CFG_SCC_TOUT_LOOP 1000000 +#endif static char txbuf[TX_BUF_CNT][ DBUF_LENGTH ]; @@ -109,7 +111,7 @@ int eth_send(volatile void *packet, int length) } for(i=0; rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) { - if (i >= TOUT_LOOP) { + if (i >= CFG_SCC_TOUT_LOOP) { puts ("scc: tx buffer not ready\n"); goto out; } @@ -121,7 +123,7 @@ int eth_send(volatile void *packet, int length) BD_ENET_TX_WRAP); for(i=0; rtx->txbd[txIdx].cbd_sc & BD_ENET_TX_READY; i++) { - if (i >= TOUT_LOOP) { + if (i >= CFG_SCC_TOUT_LOOP) { puts ("scc: tx error\n"); goto out; } @@ -262,7 +264,6 @@ int eth_init(bd_t *bis) pram_ptr->sen_taddrm = 0x0; /* Tmp Address (unused) */ pram_ptr->sen_taddrl = 0x0; /* Tmp Address (LSB) (unused) */ - /* 24.21 - (19): Initialize RxBD */ for (i = 0; i < PKTBUFSRX; i++) { diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h new file mode 100644 index 00000000000..ab2877858b7 --- /dev/null +++ b/include/configs/mgcoge.h @@ -0,0 +1,317 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8247 1 +#define CONFIG_MPC8272_FAMILY 1 +#define CONFIG_MGCOGE 1 + +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#undef DEBUG + +/* + * Select serial console configuration + * + * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + */ +#define CONFIG_CONS_ON_SMC /* Console is on SMC */ +#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ +#undef CONFIG_CONS_NONE /* It's not on external UART */ +#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */ + +/* + * Select ethernet configuration + * + * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, + * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for + * SCC, 1-3 for FCC) + * + * If CONFIG_ETHER_NONE is defined, then either the ethernet routines + * must be defined elsewhere (as for the console), or CONFIG_CMD_NET + * must be unset. + */ +#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */ +#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */ +#undef CONFIG_ETHER_NONE /* No external Ethernet */ + +#define CONFIG_ETHER_INDEX 4 +#define CFG_SCC_TOUT_LOOP 10000000 + +# define CFG_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8) + +#ifndef CONFIG_8260_CLKIN +#define CONFIG_8260_CLKIN 66000000 /* in Hz */ +#endif + +#define CONFIG_BAUDRATE 115200 + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_IMMAP +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING + +/* + * Default environment settings + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "u-boot_addr=100000\0" \ + "kernel_addr=200000\0" \ + "fdt_addr=400000\0" \ + "rootpath=/opt/eldk-4.2/ppc_82xx\0" \ + "u-boot=/tftpboot/mgcoge/u-boot.bin\0" \ + "bootfile=/tftpboot/mgcoge/uImage\0" \ + "fdt_file=/tftpboot/mgcoge/mgcoge.dtb\0" \ + "load=tftp ${u-boot_addr} ${u-boot}\0" \ + "update=prot off fe000000 fe03ffff; era fe000000 fe03ffff; " \ + "cp.b ${u-boot_addr} fe000000 ${filesize};" \ + "prot on fe000000 fe03ffff\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "addcon=setenv bootargs ${bootargs} console=ttyCPM0,,${baudrate}\0" \ + "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:" \ + "${netmask}:${hostname}:${netdev}:on panic=1 " \ + "console=${console}\0" \ + "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcon;"\ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_self=tftp ${kernel_addr} ${bootfile}; " \ + "tftp ${fdt_addr} ${fdt_file}; " \ + "tftp ${ramdisk_addr} ${ramdisk_file}; " \ + "run ramargs addip; " \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run net_nfs" +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFE000000 +#define CFG_FLASH_SIZE 32 +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */ + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +#define CFG_RAMBOOT +#endif + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */ + +#define CFG_ENV_IS_IN_FLASH + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#endif /* CFG_ENV_IS_IN_FLASH */ + +#define CFG_IMMR 0xF0000000 + +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* Hard reset configuration word */ +#define CFG_HRCW_MASTER 0x0604b211 + +/* No slaves */ +#define CFG_HRCW_SLAVE1 0 +#define CFG_HRCW_SLAVE2 0 +#define CFG_HRCW_SLAVE3 0 +#define CFG_HRCW_SLAVE4 0 +#define CFG_HRCW_SLAVE5 0 +#define CFG_HRCW_SLAVE6 0 +#define CFG_HRCW_SLAVE7 0 + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) + +#define CFG_HID2 0 + +#define CFG_SIUMCR 0x4020c200 +#define CFG_SYPCR 0xFFFFFFC3 +#define CFG_BCR 0x10000000 +#define CFG_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK) + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CFG_RMR 0 + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CFG_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 8 bit FLASH + * 1 60x SDRAM 32 bit SDRAM + * + */ +/* Bank 0 - FLASH + */ +#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX ) + + +/* Bank 1 - 60x bus SDRAM + */ +#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ +#define CFG_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */ + +#define CFG_MPTPR 0x1800 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + */ +#define CFG_MRS_OFFS 0x00000110 +#define CFG_PSRT 0x0e + +#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CFG_OR1_PRELIM CFG_OR1 + +/* SDRAM initialization values +*/ + +#define CFG_OR1 ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_8 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + +#define CFG_PSDMR (PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_5_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,8247@0" +#define OF_SOC "soc@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc/cpm/serial@11a90" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From 5aa437baae5fe629abeab99bef793a2a1fc71b58 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 01:12:09 +0100 Subject: Fix defaultconfig for the mgcoge board. Signed-off-by: Heiko Schocher --- include/configs/mgcoge.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h index ab2877858b7..3de24669fdf 100644 --- a/include/configs/mgcoge.h +++ b/include/configs/mgcoge.h @@ -108,7 +108,7 @@ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:" \ - "${netmask}:${hostname}:${netdev}:on panic=1 " \ + "${netmask}:${hostname}:${netdev}:off panic=1 " \ "console=${console}\0" \ "net_nfs=tftp ${kernel_addr} ${bootfile}; " \ "tftp ${fdt_addr} ${fdt_file}; run nfsargs addip addcon;"\ -- cgit v1.3.1 From 5fb2b2342ece8d786c6f7fdba1bc273febd3b3d2 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 15:15:15 +0100 Subject: added the config File for the MUNICes board. Signed-off-by: Heiko Schocher --- include/configs/munices.h | 214 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 214 insertions(+) create mode 100644 include/configs/munices.h (limited to 'include') diff --git a/include/configs/munices.h b/include/configs/munices.h new file mode 100644 index 00000000000..4359e29050f --- /dev/null +++ b/include/configs/munices.h @@ -0,0 +1,214 @@ +/* + * (C) Copyright 2007 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ +#define CONFIG_MPC5200_DDR 1 /* (with DDR-SDRAM) */ +#define CONFIG_MUNICES 1 /* ... on MUNICes board */ +#define CFG_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IMMAP +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#undef CONFIG_BOOTARGS + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run net_nfs\" to load Kernel over TFTP and to mount root filesystem over NFS;" \ + "echo" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=5\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=/tftpboot/munices/u-boot.bin\0" \ + "update=tftpboot 200000 ${bootfile};protect off fff00000 fff3ffff;" \ + "erase fff00000 fff3ffff; cp.b 200000 FFF00000 ${filesize}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run net_nfs" + +/* + * IPB Bus clocking configuration. + */ +#define CFG_IPBSPEED_133 /* define for 133MHz speed */ +#if defined(CFG_IPBSPEED_133) +/* + * PCI Bus clocking configuration + * + * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if + * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't + * been tested with a IPB Bus Clock of 66 MHz. + */ +#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#else +#undef CFG_PCISPEED_66 /* for 33MHz speed */ +#endif + +/* + * Memory map + */ +#define CFG_MBAR 0xF0000000 /* MBAR hast to be switched by other bootloader or debugger config */ +#define CFG_SDRAM_BASE 0x00000000 +/* Use SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Flash configuration + */ +#define CFG_FLASH_BASE 0xFF000000 +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +//#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_SIZE 0x01000000 /* 16 MByte */ +#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks (= chip selects) */ +#define CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +/* + * Chip selects configuration + */ +/* Boot Chipselect */ +#define CFG_BOOTCS_START CFG_FLASH_BASE +#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE +#define CFG_BOOTCS_CFG 0x00047800 + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x40000 +#define CFG_ENV_ADDR (TEXT_BASE + CFG_ENV_OFFSET) +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_SIZE 0x4000 +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR_REDUND (TEXT_BASE + CFG_ENV_OFFSET_REDUND) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_OVERWRITE 1 + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_PHY_ADDR 0x01 +#define CONFIG_MII 1 + +/* + * GPIO configuration + */ +#define CFG_GPS_PORT_CONFIG 0x00058044 /* PSC1=UART, PSC2=UART ; Ether=100MBit with MD + no PCI */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x200000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_DISPLAY_BOARDINFO 1 +#define CONFIG_CMDLINE_EDITING 1 + +/* + * Various low-level settings + */ +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333333 +#define CFG_RESET_ADDRESS 0xff000000 + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5200@0" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_SOC "soc5200@f0000000" +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" + +#endif /* __CONFIG_H */ -- cgit v1.3.1 From fa05664cd8c7ab1ecf062aa73b992b7b58bba49c Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 11 Jan 2008 15:15:16 +0100 Subject: MUNICes: Set the right CFG_DEFAULT_MBAR value. Signed-off-by: Heiko Schocher --- include/configs/munices.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/munices.h b/include/configs/munices.h index 4359e29050f..e47227094ee 100644 --- a/include/configs/munices.h +++ b/include/configs/munices.h @@ -108,6 +108,8 @@ * Memory map */ #define CFG_MBAR 0xF0000000 /* MBAR hast to be switched by other bootloader or debugger config */ + +#define CFG_DEFAULT_MBAR 0x80000000 #define CFG_SDRAM_BASE 0x00000000 /* Use SRAM until RAM will be available */ #define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -- cgit v1.3.1 From a10ff9196183e7e5f2ae3c4f5f3cbe92ae9cb719 Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sat, 12 Jan 2008 01:05:50 +0100 Subject: Coding Style cleanup; update CHANGELOG. Signed-off-by: Wolfgang Denk --- CHANGELOG | 41 +++++++++++++++++++++++++++++++++++++++++ include/configs/munices.h | 1 - 2 files changed, 41 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/CHANGELOG b/CHANGELOG index edd4bcd9b82..17e9c68d7aa 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,3 +1,44 @@ +commit f6db945649e5e9d0c7efe33b507d243cdc86cf03 +Author: Heiko Schocher +Date: Fri Jan 11 15:15:17 2008 +0100 + + Fixed syntax error in function init_e300_core() of mpc83xx/start.S if + + Signed-off-by: Timur Tabi + Signed-off-by: Heiko Schocher + +commit fa05664cd8c7ab1ecf062aa73b992b7b58bba49c +Author: Heiko Schocher +Date: Fri Jan 11 15:15:16 2008 +0100 + + MUNICes: Set the right CFG_DEFAULT_MBAR value. + + Signed-off-by: Heiko Schocher + +commit 5fb2b2342ece8d786c6f7fdba1bc273febd3b3d2 +Author: Heiko Schocher +Date: Fri Jan 11 15:15:15 2008 +0100 + + added the config File for the MUNICes board. + + Signed-off-by: Heiko Schocher + +commit 6341d9d723b71b4c0bf86f979e4cb228c02fd09d +Author: Heiko Schocher +Date: Fri Jan 11 15:15:14 2008 +0100 + + added basic support for the MUNICes board. + + Signed-off-by: Heiko Schocher + +commit 3bb77fb09a1caabf5a292cc5b486a78b977fbe19 +Author: Wolfgang Denk +Date: Sat Jan 12 00:39:37 2008 +0100 + + Update CHANGELOG and MAINTAINERS files. + + Signed-off-by: Wolfgang Denk + commit 5ba7390c3cb579172be66888a371707b47b5be4e Author: Anatolij Gustschin Date: Fri Jan 11 02:15:02 2008 +0100 diff --git a/include/configs/munices.h b/include/configs/munices.h index e47227094ee..2372b5763b8 100644 --- a/include/configs/munices.h +++ b/include/configs/munices.h @@ -133,7 +133,6 @@ #define CFG_FLASH_BASE 0xFF000000 #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ #define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -//#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } #define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #define CFG_FLASH_EMPTY_INFO #define CFG_FLASH_SIZE 0x01000000 /* 16 MByte */ -- cgit v1.3.1 From 281ff9a45cf9eb17b8a9afc436cb783cf1f62363 Mon Sep 17 00:00:00 2001 From: Grzegorz Bernacki Date: Tue, 8 Jan 2008 17:16:15 +0100 Subject: ads5121: Added support for FDT. Signed-off-by: Grzegorz Bernacki --- board/ads5121/ads5121.c | 8 ++++++++ cpu/mpc512x/cpu.c | 21 +++++++++++++++++++++ include/asm-ppc/u-boot.h | 3 +++ include/configs/ads5121.h | 8 ++++++++ lib_ppc/board.c | 3 +++ 5 files changed, 43 insertions(+) (limited to 'include') diff --git a/board/ads5121/ads5121.c b/board/ads5121/ads5121.c index f275ce7de03..46be6a516ae 100644 --- a/board/ads5121/ads5121.c +++ b/board/ads5121/ads5121.c @@ -184,3 +184,11 @@ int checkboard (void) brd_rev, cpld_rev); return 0; } + +#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); + fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ diff --git a/cpu/mpc512x/cpu.c b/cpu/mpc512x/cpu.c index accae6e066e..6421a511e42 100644 --- a/cpu/mpc512x/cpu.c +++ b/cpu/mpc512x/cpu.c @@ -32,6 +32,10 @@ #include #include +#if defined(CONFIG_OF_LIBFDT) +#include +#endif + DECLARE_GLOBAL_DATA_PTR; int checkcpu (void) @@ -125,3 +129,20 @@ void watchdog_reset (void) enable_interrupts (); } #endif + +#ifdef CONFIG_OF_LIBFDT +void ft_cpu_setup(void *blob, bd_t *bd) +{ + char * cpu_path = "/cpus/" OF_CPU; + char * eth_path = "/" OF_SOC "/ethernet@2800"; + + do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", OF_TBCLK, 1); + do_fixup_by_path_u32(blob, cpu_path, "bus-frequency", bd->bi_busfreq, 1); + do_fixup_by_path_u32(blob, cpu_path, "ref-frequency", CFG_MPC512X_CLKIN, 1); + do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1); + do_fixup_by_path_u32(blob, "/" OF_SOC, "bus-frequency", bd->bi_ipsfreq, 1); + do_fixup_by_path_u32(blob, "/" OF_SOC, "ref-frequency", CFG_MPC512X_CLKIN, 1); + do_fixup_by_path(blob, eth_path, "address", bd->bi_enetaddr, 6, 0); + do_fixup_by_path(blob, eth_path, "local-mac-address", bd->bi_enetaddr, 6, 0); +} +#endif diff --git a/include/asm-ppc/u-boot.h b/include/asm-ppc/u-boot.h index bd9b6f70dda..2b31814b666 100644 --- a/include/asm-ppc/u-boot.h +++ b/include/asm-ppc/u-boot.h @@ -74,6 +74,9 @@ typedef struct bd_info { unsigned long bi_sccfreq; /* SCC_CLK Freq, in MHz */ unsigned long bi_vco; /* VCO Out from PLL, in MHz */ #endif +#if defined(CONFIG_MPC512X) + unsigned long bi_ipsfreq; /* IPS Bus Freq, in MHz */ +#endif /* CONFIG_MPC512X */ #if defined(CONFIG_MPC5xxx) unsigned long bi_ipbfreq; /* IPB Bus Freq, in MHz */ unsigned long bi_pcifreq; /* PCI Bus Freq, in MHz */ diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h index 58060a8c8a5..11e7e4431ef 100644 --- a/include/configs/ads5121.h +++ b/include/configs/ads5121.h @@ -407,4 +407,12 @@ #define CONFIG_BOOTCOMMAND "run flash_self" +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_CPU "PowerPC,5121@0" +#define OF_SOC "soc5121@80000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5121@80000000/serial@11300" + #endif /* __CONFIG_H */ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 07197450666..63509186078 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -555,6 +555,9 @@ void board_init_f (ulong bootflag) bd->bi_sccfreq = gd->scc_clk; bd->bi_vco = gd->vco_out; #endif /* CONFIG_CPM2 */ +#if defined(CONFIG_MPC512X) + bd->bi_ipsfreq = gd->ipb_clk; +#endif /* CONFIG_MPC512X */ #if defined(CONFIG_MPC5xxx) bd->bi_ipbfreq = gd->ipb_clk; bd->bi_pcifreq = gd->pci_clk; -- cgit v1.3.1 From 66a9455b6bf46d69cec5c88d1a600d1d9a10670d Mon Sep 17 00:00:00 2001 From: Grzegorz Bernacki Date: Tue, 8 Jan 2008 17:16:59 +0100 Subject: MPC512X: Fixed typo in macro name. Signed-off-by: Grzegorz Bernacki --- include/common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/common.h b/include/common.h index 9ef93444125..54083f10c54 100644 --- a/include/common.h +++ b/include/common.h @@ -468,7 +468,7 @@ int prt_8260_clks (void); #elif defined(CONFIG_MPC5xxx) int prt_mpc5xxx_clks (void); #endif -#if defined(CONFIG_MPC512x) +#if defined(CONFIG_MPC512X) int prt_mpc512xxx_clks (void); #endif #if defined(CONFIG_MPC8220) -- cgit v1.3.1 From 5d49e0e152a8b81cc0602271e8fd259371f559b7 Mon Sep 17 00:00:00 2001 From: Grzegorz Bernacki Date: Fri, 11 Jan 2008 12:03:43 +0100 Subject: MPC512X: Cleanup bus clock names. Signed-off-by: Grzegorz Bernacki --- cpu/mpc512x/fec.c | 2 +- cpu/mpc512x/i2c.c | 12 ++++++------ cpu/mpc512x/serial.c | 2 +- cpu/mpc512x/speed.c | 4 ++-- include/asm-ppc/global_data.h | 2 +- lib_ppc/board.c | 2 +- 6 files changed, 12 insertions(+), 12 deletions(-) (limited to 'include') diff --git a/cpu/mpc512x/fec.c b/cpu/mpc512x/fec.c index 675b7a2e09e..c226a8a5a20 100644 --- a/cpu/mpc512x/fec.c +++ b/cpu/mpc512x/fec.c @@ -299,7 +299,7 @@ int mpc512x_fec_init_phy (struct eth_device *dev, bd_t * bis) * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock * and do not drop the Preamble. */ - fec->eth->mii_speed = (((gd->ipb_clk / 1000000) / 5) + 1) << 1; + fec->eth->mii_speed = (((gd->ips_clk / 1000000) / 5) + 1) << 1; /* * Reset PHY, then delay 300ns diff --git a/cpu/mpc512x/i2c.c b/cpu/mpc512x/i2c.c index 00e28d6404d..56ba4437269 100644 --- a/cpu/mpc512x/i2c.c +++ b/cpu/mpc512x/i2c.c @@ -236,7 +236,7 @@ static int mpc_get_fdr (int speed) if (fdr == -1) { ulong best_speed = 0; ulong divider; - ulong ipb, scl; + ulong ips, scl; ulong bestmatch = 0xffffffffUL; int best_i = 0, best_j = 0, i, j; int SCL_Tap[] = { 9, 10, 12, 15, 5, 6, 7, 8}; @@ -251,18 +251,18 @@ static int mpc_get_fdr (int speed) {126, 128} }; - ipb = gd->ipb_clk; + ips = gd->ips_clk; for (i = 7; i >= 0; i--) { for (j = 7; j >= 0; j--) { scl = 2 * (scltap[j].scl2tap + (SCL_Tap[i] - 1) * scltap[j].tap2tap + 2); - if (ipb <= speed*scl) { - if ((speed*scl - ipb) < bestmatch) { - bestmatch = speed*scl - ipb; + if (ips <= speed*scl) { + if ((speed*scl - ips) < bestmatch) { + bestmatch = speed*scl - ips; best_i = i; best_j = j; - best_speed = ipb/scl; + best_speed = ips/scl; } } } diff --git a/cpu/mpc512x/serial.c b/cpu/mpc512x/serial.c index 200ff2c4964..8a214041ad8 100644 --- a/cpu/mpc512x/serial.c +++ b/cpu/mpc512x/serial.c @@ -86,7 +86,7 @@ int serial_init(void) psc->mode = PSC_MODE_1_STOPBIT; /* calculate dividor for setting PSC CTUR and CTLR registers */ - baseclk = (gd->ipb_clk + 8) / 16; + baseclk = (gd->ips_clk + 8) / 16; div = (baseclk + (gd->baudrate / 2)) / gd->baudrate; psc->ctur = (div >> 8) & 0xff; diff --git a/cpu/mpc512x/speed.c b/cpu/mpc512x/speed.c index a609827387b..99e3495c2fd 100644 --- a/cpu/mpc512x/speed.c +++ b/cpu/mpc512x/speed.c @@ -96,7 +96,7 @@ int get_clocks (void) ips_clk = 0; } - gd->ipb_clk = ips_clk; + gd->ips_clk = ips_clk; gd->csb_clk = csb_clk; gd->cpu_clk = core_clk; gd->bus_clk = csb_clk; @@ -118,7 +118,7 @@ int do_clocks (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]) printf ("Clock configuration:\n"); printf (" CPU: %4d MHz\n", gd->cpu_clk / 1000000); printf (" Coherent System Bus: %4d MHz\n", gd->csb_clk / 1000000); - printf (" IPS Bus: %4d MHz\n", gd->ipb_clk / 1000000); + printf (" IPS Bus: %4d MHz\n", gd->ips_clk / 1000000); printf (" DDR: %4d MHz\n", 2 * gd->csb_clk / 1000000); return 0; } diff --git a/include/asm-ppc/global_data.h b/include/asm-ppc/global_data.h index c3b5e8292e5..aa6384c1524 100644 --- a/include/asm-ppc/global_data.h +++ b/include/asm-ppc/global_data.h @@ -99,7 +99,7 @@ typedef struct global_data { unsigned long pci_clk; #endif #if defined(CONFIG_MPC512X) - u32 ipb_clk; + u32 ips_clk; u32 csb_clk; #endif /* CONFIG_MPC512X */ #if defined(CONFIG_MPC8220) diff --git a/lib_ppc/board.c b/lib_ppc/board.c index 63509186078..7b95246e110 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -556,7 +556,7 @@ void board_init_f (ulong bootflag) bd->bi_vco = gd->vco_out; #endif /* CONFIG_CPM2 */ #if defined(CONFIG_MPC512X) - bd->bi_ipsfreq = gd->ipb_clk; + bd->bi_ipsfreq = gd->ips_clk; #endif /* CONFIG_MPC512X */ #if defined(CONFIG_MPC5xxx) bd->bi_ipbfreq = gd->ipb_clk; -- cgit v1.3.1 From 2b2f43ed6a30ece77f76191c845ac95267daa31a Mon Sep 17 00:00:00 2001 From: Wolfgang Denk Date: Sun, 13 Jan 2008 02:19:44 +0100 Subject: MPC8360ERDK: fix incorrect initialization of CFG_I2C_NOPROBES Signed-off-by: Wolfgang Denk --- include/configs/MPC8360ERDK.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index e6d0c5e98ee..0f6f8f19c05 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -241,7 +241,7 @@ #define CONFIG_I2C_CMD_TREE #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {{0x52}} /* Don't probe these addrs */ #define CFG_I2C_OFFSET 0x3000 #define CFG_I2C2_OFFSET 0x3100 -- cgit v1.3.1