From ba2e01c72be50b49e731ef3d06a0e5f55bb328b4 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 6 Nov 2014 08:28:42 -0600 Subject: arm: omap5: don't enable misc_init_r by default Out of all OMAP5-like boards, only one of them needs CONFIG_MISC_INIT_R, so it's best to enable that for that particular board only, instead of enabling for all boards unconditionally. Signed-off-by: Felipe Balbi Reviewed-by: Tom Rini --- include/configs/cm_t54.h | 1 - include/configs/omap5_uevm.h | 1 + include/configs/ti_omap5_common.h | 1 - 3 files changed, 1 insertion(+), 2 deletions(-) (limited to 'include') diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h index 641ab48c2c8..92ce1e17dac 100644 --- a/include/configs/cm_t54.h +++ b/include/configs/cm_t54.h @@ -16,7 +16,6 @@ #include -#undef CONFIG_MISC_INIT_R #undef CONFIG_SPL_OS_BOOT /* Enable Generic board */ diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index e8dc462f146..e07795f9210 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -23,6 +23,7 @@ #define CONFIG_SYS_NS16550_COM3 UART3_BASE #define CONFIG_BAUDRATE 115200 +#define CONFIG_MISC_INIT_R /* MMC ENV related defines */ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */ diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h index 3166392c780..5b03fb182e6 100644 --- a/include/configs/ti_omap5_common.h +++ b/include/configs/ti_omap5_common.h @@ -19,7 +19,6 @@ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO -#define CONFIG_MISC_INIT_R #define CONFIG_ARCH_CPU_INIT #define CONFIG_SYS_CACHELINE_SIZE 64 -- cgit v1.3.1 From a70e157f304f578db7c99f5fba2ebeb882d736ba Mon Sep 17 00:00:00 2001 From: Franklin S Cooper Jr Date: Thu, 6 Nov 2014 08:28:47 -0600 Subject: configs: omap5_common : Boot rootfs from sd card by default * Since the emmc isn't always programed trying to load the fs from the emmc causes boot failures/kernel panic. * The current bootcmd is set to: bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \ setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot; My guess is the env variables should be set so that sd card boot (dt,kernel,fs) is the default and then fallback to emmc if it fails (no sd card detected) The current bootcmd attempts to set mmcroot to the sd card rootfs but that code doesn't run due to mmcboot being ran early on. Signed-off-by: Franklin Cooper Jr. Signed-off-by: Felipe Balbi Reviewed-by: Tom Rini --- include/configs/ti_omap5_common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h index 5b03fb182e6..de96d7dadaa 100644 --- a/include/configs/ti_omap5_common.h +++ b/include/configs/ti_omap5_common.h @@ -78,7 +78,7 @@ "partitions=" PARTS_DEFAULT "\0" \ "optargs=\0" \ "mmcdev=0\0" \ - "mmcroot=/dev/mmcblk1p2 rw\0" \ + "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext4 rootwait\0" \ "mmcargs=setenv bootargs console=${console} " \ "${optargs} " \ -- cgit v1.3.1 From d11ac4b56d993153f9d72208809060f3b6c9af76 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Thu, 6 Nov 2014 08:28:51 -0600 Subject: arm: omap: add support for am57xx devices just add a few ifdefs around because this device is very similar to dra7xxx. Signed-off-by: Felipe Balbi Reviewed-by: Tom Rini --- arch/arm/cpu/armv7/omap-common/boot-common.c | 2 +- arch/arm/include/asm/arch-omap5/clock.h | 2 +- arch/arm/include/asm/arch-omap5/omap.h | 4 ++-- drivers/mmc/omap_hsmmc.c | 5 +++-- drivers/power/palmas.c | 2 +- drivers/spi/ti_qspi.c | 8 ++++---- include/linux/usb/xhci-omap.h | 4 ++++ 7 files changed, 16 insertions(+), 11 deletions(-) (limited to 'include') diff --git a/arch/arm/cpu/armv7/omap-common/boot-common.c b/arch/arm/cpu/armv7/omap-common/boot-common.c index fb535eb9ecc..b819fe2e642 100644 --- a/arch/arm/cpu/armv7/omap-common/boot-common.c +++ b/arch/arm/cpu/armv7/omap-common/boot-common.c @@ -57,7 +57,7 @@ void save_omap_boot_params(void) } } -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) /* * We get different values for QSPI_1 and QSPI_4 being used, but * don't actually care about this difference. Rather than diff --git a/arch/arm/include/asm/arch-omap5/clock.h b/arch/arm/include/asm/arch-omap5/clock.h index 7eacba26862..0dc584b8ce6 100644 --- a/arch/arm/include/asm/arch-omap5/clock.h +++ b/arch/arm/include/asm/arch-omap5/clock.h @@ -314,7 +314,7 @@ */ #define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219 -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) #define V_OSCK 20000000 /* Clock output from T2 */ #else #define V_OSCK 19200000 /* Clock output from T2 */ diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h index b9600cf42db..e2181598d5d 100644 --- a/arch/arm/include/asm/arch-omap5/omap.h +++ b/arch/arm/include/asm/arch-omap5/omap.h @@ -27,7 +27,7 @@ #define CONTROL_CORE_ID_CODE 0x4A002204 #define CONTROL_WKUP_ID_CODE 0x4AE0C204 -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) #define CONTROL_ID_CODE CONTROL_WKUP_ID_CODE #else #define CONTROL_ID_CODE CONTROL_CORE_ID_CODE @@ -163,7 +163,7 @@ struct s32ktimer { * much larger) and do not, at this time, make use of the additional * space. */ -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) #define NON_SECURE_SRAM_START 0x40300000 #define NON_SECURE_SRAM_END 0x40380000 /* Not inclusive */ #else diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index ffb5284a00e..bada0066ecd 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -663,7 +663,8 @@ int omap_mmc_init(int dev_index, uint host_caps_mask, uint f_max, int cd_gpio, case 1: priv_data->base_addr = (struct hsmmc *)OMAP_HSMMC2_BASE; #if (defined(CONFIG_OMAP44XX) || defined(CONFIG_OMAP54XX) || \ - defined(CONFIG_DRA7XX)) && defined(CONFIG_HSMMC2_8BIT) + defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX)) && \ + defined(CONFIG_HSMMC2_8BIT) /* Enable 8-bit interface for eMMC on OMAP4/5 or DRA7XX */ host_caps_val |= MMC_MODE_8BIT; #endif @@ -672,7 +673,7 @@ int omap_mmc_init(int dev_index, uint host_caps_mask, uint f_max, int cd_gpio, #ifdef OMAP_HSMMC3_BASE case 2: priv_data->base_addr = (struct hsmmc *)OMAP_HSMMC3_BASE; -#if defined(CONFIG_DRA7XX) && defined(CONFIG_HSMMC3_8BIT) +#if (defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX)) && defined(CONFIG_HSMMC3_8BIT) /* Enable 8-bit interface for eMMC on DRA7XX */ host_caps_val |= MMC_MODE_8BIT; #endif diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c index cfbc9dc5220..6430fe004d5 100644 --- a/drivers/power/palmas.c +++ b/drivers/power/palmas.c @@ -27,7 +27,7 @@ int palmas_mmc1_poweron_ldo(void) { u8 val = 0; -#if defined(CONFIG_DRA7XX) +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) /* * Currently valid for the dra7xx_evm board: * Set TPS659038 LDO1 to 3.0 V diff --git a/drivers/spi/ti_qspi.c b/drivers/spi/ti_qspi.c index fd7fea8df5b..857b60455a9 100644 --- a/drivers/spi/ti_qspi.c +++ b/drivers/spi/ti_qspi.c @@ -102,7 +102,7 @@ static void ti_spi_setup_spi_register(struct ti_qspi_slave *qslave) struct spi_slave *slave = &qslave->slave; u32 memval = 0; -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) slave->memory_map = (void *)MMAP_START_ADDR_DRA; #else slave->memory_map = (void *)MMAP_START_ADDR_AM43x; @@ -244,7 +244,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, uint status; int timeout; -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) int val; #endif @@ -254,7 +254,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, /* Setup mmap flags */ if (flags & SPI_XFER_MMAP) { writel(MM_SWITCH, &qslave->base->memswitch); -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) val = readl(CORE_CTRL_IO); val |= MEM_CS; writel(val, CORE_CTRL_IO); @@ -262,7 +262,7 @@ int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout, return 0; } else if (flags & SPI_XFER_MMAP_END) { writel(~MM_SWITCH, &qslave->base->memswitch); -#ifdef CONFIG_DRA7XX +#if defined(CONFIG_DRA7XX) || defined(CONFIG_AM57XX) val = readl(CORE_CTRL_IO); val &= MEM_CS_UNSELECT; writel(val, CORE_CTRL_IO); diff --git a/include/linux/usb/xhci-omap.h b/include/linux/usb/xhci-omap.h index 82630adc711..cb166e6a6c6 100644 --- a/include/linux/usb/xhci-omap.h +++ b/include/linux/usb/xhci-omap.h @@ -14,6 +14,10 @@ #define OMAP_XHCI_BASE 0x488d0000 #define OMAP_OCP1_SCP_BASE 0x4A081000 #define OMAP_OTG_WRAPPER_BASE 0x488c0000 +#elif defined CONFIG_AM57XX +#define OMAP_XHCI_BASE 0x48890000 +#define OMAP_OCP1_SCP_BASE 0x4A084c00 +#define OMAP_OTG_WRAPPER_BASE 0x48880000 #elif defined CONFIG_AM43XX #define OMAP_XHCI_BASE 0x483d0000 #define OMAP_OCP1_SCP_BASE 0x483E8000 -- cgit v1.3.1 From 1e4ad74b875f4da91193afffb0bb0db90ec7b886 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Mon, 10 Nov 2014 14:02:44 -0600 Subject: beagle_x15: add board support for Beagle x15 BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: http://www.elinux.org/Beagleboard:BeagleBoard-X15 Signed-off-by: Felipe Balbi Signed-off-by: Nishanth Menon Reviewed-by: Tom Rini --- arch/arm/cpu/armv7/omap5/Kconfig | 4 + board/ti/beagle_x15/Kconfig | 12 ++ board/ti/beagle_x15/Makefile | 8 + board/ti/beagle_x15/board.c | 395 ++++++++++++++++++++++++++++++++++++++ board/ti/beagle_x15/mux_data.h | 55 ++++++ configs/beagle_x15_defconfig | 5 + include/configs/beagle_x15.h | 88 +++++++++ include/configs/ti_omap5_common.h | 2 + 8 files changed, 569 insertions(+) create mode 100644 board/ti/beagle_x15/Kconfig create mode 100644 board/ti/beagle_x15/Makefile create mode 100644 board/ti/beagle_x15/board.c create mode 100644 board/ti/beagle_x15/mux_data.h create mode 100644 configs/beagle_x15_defconfig create mode 100644 include/configs/beagle_x15.h (limited to 'include') diff --git a/arch/arm/cpu/armv7/omap5/Kconfig b/arch/arm/cpu/armv7/omap5/Kconfig index 129982cacac..aca862d2b28 100644 --- a/arch/arm/cpu/armv7/omap5/Kconfig +++ b/arch/arm/cpu/armv7/omap5/Kconfig @@ -12,6 +12,9 @@ config TARGET_OMAP5_UEVM config TARGET_DRA7XX_EVM bool "TI DRA7XX" +config TARGET_BEAGLE_X15 + bool "BeagleBoard X15" + endchoice config SYS_SOC @@ -20,5 +23,6 @@ config SYS_SOC source "board/compulab/cm_t54/Kconfig" source "board/ti/omap5_uevm/Kconfig" source "board/ti/dra7xx/Kconfig" +source "board/ti/beagle_x15/Kconfig" endif diff --git a/board/ti/beagle_x15/Kconfig b/board/ti/beagle_x15/Kconfig new file mode 100644 index 00000000000..a305ff1044e --- /dev/null +++ b/board/ti/beagle_x15/Kconfig @@ -0,0 +1,12 @@ +if TARGET_BEAGLE_X15 + +config SYS_BOARD + default "beagle_x15" + +config SYS_VENDOR + default "ti" + +config SYS_CONFIG_NAME + default "beagle_x15" + +endif diff --git a/board/ti/beagle_x15/Makefile b/board/ti/beagle_x15/Makefile new file mode 100644 index 00000000000..5cd6873f5e9 --- /dev/null +++ b/board/ti/beagle_x15/Makefile @@ -0,0 +1,8 @@ +# +# (C) Copyright 2014 +# Texas Instruments, +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := board.o diff --git a/board/ti/beagle_x15/board.c b/board/ti/beagle_x15/board.c new file mode 100644 index 00000000000..db96e347e7a --- /dev/null +++ b/board/ti/beagle_x15/board.c @@ -0,0 +1,395 @@ +/* + * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com + * + * Author: Felipe Balbi + * + * Based on board/ti/dra7xx/evm.c + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "mux_data.h" + +#ifdef CONFIG_DRIVER_TI_CPSW +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +const struct omap_sysinfo sysinfo = { + "Board: BeagleBoard x15\n" +}; + +static const struct dmm_lisa_map_regs beagle_x15_lisa_regs = { + .dmm_lisa_map_3 = 0x80740300, + .is_ma_present = 0x1 +}; + +void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs) +{ + *dmm_lisa_regs = &beagle_x15_lisa_regs; +} + +static const struct emif_regs beagle_x15_emif1_ddr3_532mhz_emif_regs = { + .sdram_config_init = 0x61851b32, + .sdram_config = 0x61851b32, + .sdram_config2 = 0x00000000, + .ref_ctrl = 0x00001035, + .sdram_tim1 = 0xceef266b, + .sdram_tim2 = 0x328f7fda, + .sdram_tim3 = 0x027f88a8, + .read_idle_ctrl = 0x00050001, + .zq_config = 0x0007190b, + .temp_alert_config = 0x00000000, + .emif_ddr_phy_ctlr_1_init = 0x0e24400a, + .emif_ddr_phy_ctlr_1 = 0x0e24400a, + .emif_ddr_ext_phy_ctrl_1 = 0x10040100, + .emif_ddr_ext_phy_ctrl_2 = 0x00740074, + .emif_ddr_ext_phy_ctrl_3 = 0x00780078, + .emif_ddr_ext_phy_ctrl_4 = 0x007c007c, + .emif_ddr_ext_phy_ctrl_5 = 0x007b007b, + .emif_rd_wr_lvl_rmp_win = 0x00000000, + .emif_rd_wr_lvl_rmp_ctl = 0x00000000, + .emif_rd_wr_lvl_ctl = 0x00000000, + .emif_rd_wr_exec_thresh = 0x00000305 +}; + +static const u32 beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs[] = { + 0x00800080, + 0x00360036, + 0x00340034, + 0x00360036, + 0x00350035, + 0x00350035, + + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + + 0x00430043, + 0x003e003e, + 0x004a004a, + 0x00470047, + 0x00400040, + + 0x00000000, + 0x00600020, + 0x40010080, + 0x08102040, + + 0x00400040, + 0x00400040, + 0x00400040, + 0x00400040, + 0x00400040 +}; + +static const struct emif_regs beagle_x15_emif2_ddr3_532mhz_emif_regs = { + .sdram_config_init = 0x61851b32, + .sdram_config = 0x61851b32, + .sdram_config2 = 0x00000000, + .ref_ctrl = 0x00001035, + .sdram_tim1 = 0xceef266b, + .sdram_tim2 = 0x328f7fda, + .sdram_tim3 = 0x027f88a8, + .read_idle_ctrl = 0x00050001, + .zq_config = 0x0007190b, + .temp_alert_config = 0x00000000, + .emif_ddr_phy_ctlr_1_init = 0x0e24400a, + .emif_ddr_phy_ctlr_1 = 0x0e24400a, + .emif_ddr_ext_phy_ctrl_1 = 0x10040100, + .emif_ddr_ext_phy_ctrl_2 = 0x00820082, + .emif_ddr_ext_phy_ctrl_3 = 0x008b008b, + .emif_ddr_ext_phy_ctrl_4 = 0x00800080, + .emif_ddr_ext_phy_ctrl_5 = 0x007e007e, + .emif_rd_wr_lvl_rmp_win = 0x00000000, + .emif_rd_wr_lvl_rmp_ctl = 0x00000000, + .emif_rd_wr_lvl_ctl = 0x00000000, + .emif_rd_wr_exec_thresh = 0x00000305 +}; + +static const u32 beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs[] = { + 0x00800080, + 0x00370037, + 0x00390039, + 0x00360036, + 0x00370037, + 0x00350035, + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + 0x01ff01ff, + 0x00540054, + 0x00540054, + 0x004e004e, + 0x004c004c, + 0x00400040, + + 0x00000000, + 0x00600020, + 0x40010080, + 0x08102040, + + 0x00400040, + 0x00400040, + 0x00400040, + 0x00400040, + 0x00400040 +}; + +void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs) +{ + switch (emif_nr) { + case 1: + *regs = &beagle_x15_emif1_ddr3_532mhz_emif_regs; + break; + case 2: + *regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs; + break; + } +} + +void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr, const u32 **regs, u32 *size) +{ + switch (emif_nr) { + case 1: + *regs = beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs; + *size = ARRAY_SIZE(beagle_x15_emif1_ddr3_ext_phy_ctrl_const_regs); + break; + case 2: + *regs = beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs; + *size = ARRAY_SIZE(beagle_x15_emif2_ddr3_ext_phy_ctrl_const_regs); + break; + } +} + +struct vcores_data beagle_x15_volts = { + .mpu.value = VDD_MPU_DRA752, + .mpu.efuse.reg = STD_FUSE_OPP_VMIN_MPU_NOM, + .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, + .mpu.addr = TPS659038_REG_ADDR_SMPS12, + .mpu.pmic = &tps659038, + + .eve.value = VDD_EVE_DRA752, + .eve.efuse.reg = STD_FUSE_OPP_VMIN_DSPEVE_NOM, + .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, + .eve.addr = TPS659038_REG_ADDR_SMPS45, + .eve.pmic = &tps659038, + + .gpu.value = VDD_GPU_DRA752, + .gpu.efuse.reg = STD_FUSE_OPP_VMIN_GPU_NOM, + .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, + .gpu.addr = TPS659038_REG_ADDR_SMPS45, + .gpu.pmic = &tps659038, + + .core.value = VDD_CORE_DRA752, + .core.efuse.reg = STD_FUSE_OPP_VMIN_CORE_NOM, + .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, + .core.addr = TPS659038_REG_ADDR_SMPS6, + .core.pmic = &tps659038, + + .iva.value = VDD_IVA_DRA752, + .iva.efuse.reg = STD_FUSE_OPP_VMIN_IVA_NOM, + .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, + .iva.addr = TPS659038_REG_ADDR_SMPS45, + .iva.pmic = &tps659038, +}; + +void hw_data_init(void) +{ + *prcm = &dra7xx_prcm; + *dplls_data = &dra7xx_dplls; + *omap_vcores = &beagle_x15_volts; + *ctrl = &dra7xx_ctrl; +} + +int board_init(void) +{ + gpmc_init(); + gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100); + + return 0; +} + +int board_late_init(void) +{ + init_sata(0); + /* + * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds + * This is the POWERHOLD-in-Low behavior. + */ + palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1); + return 0; +} + +static void do_set_mux32(u32 base, + struct pad_conf_entry const *array, int size) +{ + int i; + struct pad_conf_entry *pad = (struct pad_conf_entry *)array; + + for (i = 0; i < size; i++, pad++) + writel(pad->val, base + pad->offset); +} + +void set_muxconf_regs_essential(void) +{ + do_set_mux32((*ctrl)->control_padconf_core_base, + core_padconf_array_essential, + sizeof(core_padconf_array_essential) / + sizeof(struct pad_conf_entry)); +} + +#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) +int board_mmc_init(bd_t *bis) +{ + omap_mmc_init(0, 0, 0, -1, -1); + omap_mmc_init(1, 0, 0, -1, -1); + return 0; +} +#endif + +#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT) +int spl_start_uboot(void) +{ + /* break into full u-boot on 'c' */ + if (serial_tstc() && serial_getc() == 'c') + return 1; + +#ifdef CONFIG_SPL_ENV_SUPPORT + env_init(); + env_relocate_spec(); + if (getenv_yesno("boot_os") != 1) + return 1; +#endif + + return 0; +} +#endif + +#ifdef CONFIG_DRIVER_TI_CPSW + +/* Delay value to add to calibrated value */ +#define RGMII0_TXCTL_DLY_VAL ((0x3 << 5) + 0x8) +#define RGMII0_TXD0_DLY_VAL ((0x3 << 5) + 0x8) +#define RGMII0_TXD1_DLY_VAL ((0x3 << 5) + 0x2) +#define RGMII0_TXD2_DLY_VAL ((0x4 << 5) + 0x0) +#define RGMII0_TXD3_DLY_VAL ((0x4 << 5) + 0x0) +#define VIN2A_D13_DLY_VAL ((0x3 << 5) + 0x8) +#define VIN2A_D17_DLY_VAL ((0x3 << 5) + 0x8) +#define VIN2A_D16_DLY_VAL ((0x3 << 5) + 0x2) +#define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0) +#define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0) + +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_addr = 1, + }, + { + .slave_reg_ofs = 0x308, + .sliver_reg_ofs = 0xdc0, + .phy_addr = 2, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .bd_ram_ofs = 0x2000, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + int ret; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + uint32_t ctrl_val; + + /* try reading mac address from efuse */ + mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); + mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); + mac_addr[0] = (mac_hi & 0xFF0000) >> 16; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = mac_hi & 0xFF; + mac_addr[3] = (mac_lo & 0xFF0000) >> 16; + mac_addr[4] = (mac_lo & 0xFF00) >> 8; + mac_addr[5] = mac_lo & 0xFF; + + if (!getenv("ethaddr")) { + printf(" not set. Validating first E-fuse MAC\n"); + + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + } + + mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); + mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); + mac_addr[0] = (mac_hi & 0xFF0000) >> 16; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = mac_hi & 0xFF; + mac_addr[3] = (mac_lo & 0xFF0000) >> 16; + mac_addr[4] = (mac_lo & 0xFF00) >> 8; + mac_addr[5] = mac_lo & 0xFF; + + if (!getenv("eth1addr")) { + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("eth1addr", mac_addr); + } + + ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); + ctrl_val |= 0x22; + writel(ctrl_val, (*ctrl)->control_core_control_io1); + + ret = cpsw_register(&cpsw_data); + if (ret < 0) + printf("Error %d registering CPSW switch\n", ret); + + return ret; +} +#endif + +#ifdef CONFIG_USB_XHCI_OMAP +int board_usb_init(int index, enum usb_init_type init) +{ + setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl, + OTG_SS_CLKCTRL_MODULEMODE_HW | OPTFCLKEN_REFCLK960M); + + return 0; +} +#endif diff --git a/board/ti/beagle_x15/mux_data.h b/board/ti/beagle_x15/mux_data.h new file mode 100644 index 00000000000..2294abec711 --- /dev/null +++ b/board/ti/beagle_x15/mux_data.h @@ -0,0 +1,55 @@ +/* + * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com + * + * Author: Felipe Balbi + * + * Based on board/ti/dra7xx/evm.c + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef _MUX_DATA_BEAGLE_X15_H_ +#define _MUX_DATA_BEAGLE_X15_H_ + +#include + +const struct pad_conf_entry core_padconf_array_essential[] = { + {MMC1_CLK, (IEN | PTU | PDIS | M0)}, /* MMC1_CLK */ + {MMC1_CMD, (IEN | PTU | PDIS | M0)}, /* MMC1_CMD */ + {MMC1_DAT0, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT0 */ + {MMC1_DAT1, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT1 */ + {MMC1_DAT2, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT2 */ + {MMC1_DAT3, (IEN | PTU | PDIS | M0)}, /* MMC1_DAT3 */ + {MMC1_SDCD, (FSC | IEN | PTU | PDIS | M0)}, /* MMC1_SDCD */ + {MMC1_SDWP, (FSC | IEN | PTD | PEN | M14)}, /* MMC1_SDWP */ + {GPMC_A19, (IEN | PTU | PDIS | M1)}, /* mmc2_dat4 */ + {GPMC_A20, (IEN | PTU | PDIS | M1)}, /* mmc2_dat5 */ + {GPMC_A21, (IEN | PTU | PDIS | M1)}, /* mmc2_dat6 */ + {GPMC_A22, (IEN | PTU | PDIS | M1)}, /* mmc2_dat7 */ + {GPMC_A23, (IEN | PTU | PDIS | M1)}, /* mmc2_clk */ + {GPMC_A24, (IEN | PTU | PDIS | M1)}, /* mmc2_dat0 */ + {GPMC_A25, (IEN | PTU | PDIS | M1)}, /* mmc2_dat1 */ + {GPMC_A26, (IEN | PTU | PDIS | M1)}, /* mmc2_dat2 */ + {GPMC_A27, (IEN | PTU | PDIS | M1)}, /* mmc2_dat3 */ + {GPMC_CS1, (IEN | PTU | PDIS | M1)}, /* mmm2_cmd */ + {UART3_RXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART3_RXD */ + {UART3_TXD, (FSC | IEN | PTU | PDIS | M0)}, /* UART3_TXD */ + {I2C1_SDA, (IEN | PTU | PDIS | M0)}, /* I2C1_SDA */ + {I2C1_SCL, (IEN | PTU | PDIS | M0)}, /* I2C1_SCL */ + {MDIO_MCLK, (PTU | PEN | M0)}, /* MDIO_MCLK */ + {MDIO_D, (IEN | PTU | PEN | M0)}, /* MDIO_D */ + {RGMII0_TXC, (M0) }, + {RGMII0_TXCTL, (M0) }, + {RGMII0_TXD3, (M0) }, + {RGMII0_TXD2, (M0) }, + {RGMII0_TXD1, (M0) }, + {RGMII0_TXD0, (M0) }, + {RGMII0_RXC, (IEN | M0) }, + {RGMII0_RXCTL, (IEN | M0) }, + {RGMII0_RXD3, (IEN | M0) }, + {RGMII0_RXD2, (IEN | M0) }, + {RGMII0_RXD1, (IEN | M0) }, + {RGMII0_RXD0, (IEN | M0) }, + {USB1_DRVVBUS, (M0 | FSC) }, + {SPI1_CS1, (PEN | IDIS | M14) }, /* GPIO7_11 */ +}; +#endif /* _MUX_DATA_BEAGLE_X15_H_ */ diff --git a/configs/beagle_x15_defconfig b/configs/beagle_x15_defconfig new file mode 100644 index 00000000000..872ab63bdd5 --- /dev/null +++ b/configs/beagle_x15_defconfig @@ -0,0 +1,5 @@ +CONFIG_SPL=y +CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=3" ++S:CONFIG_ARM=y ++S:CONFIG_OMAP54XX=y ++S:CONFIG_TARGET_BEAGLE_X15=y diff --git a/include/configs/beagle_x15.h b/include/configs/beagle_x15.h new file mode 100644 index 00000000000..cc363309383 --- /dev/null +++ b/include/configs/beagle_x15.h @@ -0,0 +1,88 @@ +/* + * (C) Copyright 2014 + * Texas Instruments Incorporated. + * Felipe Balbi + * + * Configuration settings for the TI Beagle x15 board. + * See ti_omap5_common.h for omap5 common settings. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_BEAGLE_X15_H +#define __CONFIG_BEAGLE_X15_H + +#define CONFIG_AM57XX + +#define CONFIG_NR_DRAM_BANKS 2 + +#define CONFIG_ENV_SIZE (64 << 10) +#define CONFIG_ENV_IS_IN_FAT +#define FAT_ENV_INTERFACE "mmc" +#define FAT_ENV_DEVICE_AND_PART "0:1" +#define FAT_ENV_FILE "uboot.env" + +#define CONFIG_CMD_SAVEENV + +#define CONSOLEDEV "ttyO2" +#define CONFIG_SYS_NS16550_COM1 UART1_BASE /* Base EVM has UART0 */ +#define CONFIG_SYS_NS16550_COM2 UART2_BASE /* UART2 */ +#define CONFIG_SYS_NS16550_COM3 UART3_BASE /* UART3 */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_OMAP_ABE_SYSCK + +/* Define the default GPT table for eMMC */ +#define PARTS_DEFAULT \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}" + +#include + +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + +/* CPSW Ethernet */ +#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ +#define CONFIG_MII /* Required in net/eth.c */ +#define CONFIG_PHY_GIGE /* per-board part of CPSW */ +#define CONFIG_PHYLIB + +#define CONFIG_SUPPORT_EMMC_BOOT + +/* USB xHCI HOST */ +#define CONFIG_CMD_USB +#define CONFIG_USB_HOST +#define CONFIG_USB_XHCI +#define CONFIG_USB_XHCI_OMAP +#define CONFIG_USB_STORAGE +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 + +#define CONFIG_OMAP_USB_PHY +#define CONFIG_OMAP_USB3PHY1_HOST + +/* SATA */ +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_CMD_SCSI +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +#endif /* __CONFIG_BEAGLE_X5_H */ diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h index de96d7dadaa..c47651d7962 100644 --- a/include/configs/ti_omap5_common.h +++ b/include/configs/ti_omap5_common.h @@ -117,6 +117,8 @@ "setenv fdtfile dra7-evm.dtb; fi;" \ "if test $board_name = dra72x; then " \ "setenv fdtfile dra72-evm.dtb; fi;" \ + "if test $board_name = beagle_x15; then " \ + "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \ "if test $fdtfile = undefined; then " \ "echo WARNING: Could not determine device tree to use; fi; \0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile};\0" \ -- cgit v1.3.1 From 95de9ab201e9c43c8969321711de9e93e444e420 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sat, 8 Nov 2014 20:55:45 +0100 Subject: mmc: Board-specific MMC power initializations Some devices may use non-standard combinations of regulators to power MMC: this allows these devices to provide a board-specific MMC power init function to set everything up in their own way. Signed-off-by: Paul Kocialkowski Reviewed-by: Tom Rini --- drivers/mmc/mmc.c | 7 +++++++ include/mmc.h | 1 + 2 files changed, 8 insertions(+) (limited to 'include') diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index 44a4feb96e0..8436bc7f5d3 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -1277,6 +1277,11 @@ block_dev_desc_t *mmc_get_dev(int dev) } #endif +/* board-specific MMC power initializations. */ +__weak void board_mmc_power_init(void) +{ +} + int mmc_start_init(struct mmc *mmc) { int err; @@ -1293,6 +1298,8 @@ int mmc_start_init(struct mmc *mmc) if (mmc->has_init) return 0; + board_mmc_power_init(); + /* made sure it's not NULL earlier */ err = mmc->cfg->ops->init(mmc); diff --git a/include/mmc.h b/include/mmc.h index d74a190eea0..adffc35af02 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -385,6 +385,7 @@ struct mmc *mmc_spi_init(uint bus, uint cs, uint speed, uint mode); int mmc_legacy_init(int verbose); #endif +void board_mmc_power_init(void); int board_mmc_init(bd_t *bis); int cpu_mmc_init(bd_t *bis); int mmc_get_env_addr(struct mmc *mmc, int copy, u32 *env_addr); -- cgit v1.3.1 From f3e85e4825e02fbd21859c35881f639a2c3e7afd Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sat, 8 Nov 2014 20:55:46 +0100 Subject: twl4030: device-index-specific MMC power initializations, common ramp-up delay Not every device has multiple MMC slots available, so it makes sense to enable only the required LDOs for the available slots. Generic code in omap_hsmmc will enable both VMMC1 and VMMC2, in doubt. Signed-off-by: Paul Kocialkowski Reviewed-by: Tom Rini --- drivers/mmc/omap_hsmmc.c | 4 ++-- drivers/power/twl4030.c | 28 +++++++++++++++++----------- include/twl4030.h | 2 +- 3 files changed, 20 insertions(+), 14 deletions(-) (limited to 'include') diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index bada0066ecd..3303eafa85a 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -137,8 +137,8 @@ static unsigned char mmc_board_init(struct mmc *mmc) writel(pbias_lite, &t2_base->pbias_lite); #endif #if defined(CONFIG_TWL4030_POWER) - twl4030_power_mmc_init(); - mdelay(100); /* ramp-up delay from Linux code */ + twl4030_power_mmc_init(0); + twl4030_power_mmc_init(1); #endif #if defined(CONFIG_OMAP34XX) writel(pbias_lite | PBIASLITEPWRDNZ1 | diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c index e578ae63429..7f1fdd1534c 100644 --- a/drivers/power/twl4030.c +++ b/drivers/power/twl4030.c @@ -91,17 +91,23 @@ void twl4030_power_init(void) TWL4030_PM_RECEIVER_DEV_GRP_P1); } -void twl4030_power_mmc_init(void) +void twl4030_power_mmc_init(int dev_index) { - /* Set VMMC1 to 3.15 Volts */ - twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC1_DEDICATED, - TWL4030_PM_RECEIVER_VMMC1_VSEL_32, - TWL4030_PM_RECEIVER_VMMC1_DEV_GRP, - TWL4030_PM_RECEIVER_DEV_GRP_P1); + if (dev_index == 0) { + /* Set VMMC1 to 3.15 Volts */ + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC1_DEDICATED, + TWL4030_PM_RECEIVER_VMMC1_VSEL_32, + TWL4030_PM_RECEIVER_VMMC1_DEV_GRP, + TWL4030_PM_RECEIVER_DEV_GRP_P1); - /* Set VMMC2 to 3.15 Volts */ - twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC2_DEDICATED, - TWL4030_PM_RECEIVER_VMMC2_VSEL_32, - TWL4030_PM_RECEIVER_VMMC2_DEV_GRP, - TWL4030_PM_RECEIVER_DEV_GRP_P1); + mdelay(100); /* ramp-up delay from Linux code */ + } else if (dev_index == 1) { + /* Set VMMC2 to 3.15 Volts */ + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VMMC2_DEDICATED, + TWL4030_PM_RECEIVER_VMMC2_VSEL_32, + TWL4030_PM_RECEIVER_VMMC2_DEV_GRP, + TWL4030_PM_RECEIVER_DEV_GRP_P1); + + mdelay(100); /* ramp-up delay from Linux code */ + } } diff --git a/include/twl4030.h b/include/twl4030.h index f33cd1eaed6..50f8da822af 100644 --- a/include/twl4030.h +++ b/include/twl4030.h @@ -651,7 +651,7 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val, /* For initializing power device */ void twl4030_power_init(void); /* For initializing mmc power */ -void twl4030_power_mmc_init(void); +void twl4030_power_mmc_init(int dev_index); /* * LED -- cgit v1.3.1 From 8065a4e83d0e6bc3db843b24ba58ad2ee238c0cf Mon Sep 17 00:00:00 2001 From: Lubomir Popov Date: Mon, 10 Nov 2014 18:14:18 +0200 Subject: ARM: OMAP5: DRA7xx: Enable 8-bit eMMC access on the dra7xx_evm Tested on a Vayu EVM Rev.E2 with DRA752 ES1.1 Signed-off-by: Lubomir Popov Reviewed-by: Tom Rini --- include/configs/dra7xx_evm.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 2eaabdefeea..174a711bb4b 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -50,6 +50,7 @@ #define CONFIG_EFI_PARTITION #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART +#define CONFIG_HSMMC2_8BIT /* CPSW Ethernet */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ -- cgit v1.3.1 From 0c331ebcc6843bb5e4e6727d1b4a13ef2284a5ab Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 18 Nov 2014 11:51:06 +0100 Subject: arm, am335x: siemens boards add FIT support add FIT support and set "boardid" from factoryset records "DEV/id" and "COMP/ver". "boardid" is used for selecting which fit configuration gets booted on the board. Signed-off-by: Heiko Schocher --- board/siemens/common/board.c | 9 --------- board/siemens/common/factoryset.c | 18 ++++++++---------- board/siemens/common/factoryset.h | 1 + board/siemens/draco/board.c | 9 +++++++++ board/siemens/pxm2/board.c | 34 ++++++++++++++++++++++++++++++++++ board/siemens/rut/board.c | 23 +++++++++++++++++++++++ include/configs/pxm2.h | 4 ++++ include/configs/rut.h | 4 ++++ 8 files changed, 83 insertions(+), 19 deletions(-) (limited to 'include') diff --git a/board/siemens/common/board.c b/board/siemens/common/board.c index 2782bcc2a71..cc0ac6b0bda 100644 --- a/board/siemens/common/board.c +++ b/board/siemens/common/board.c @@ -96,15 +96,6 @@ const struct dpll_params *get_dpll_ddr_params(void) return &dpll_ddr; } -#ifdef CONFIG_BOARD_LATE_INIT -int board_late_init(void) -{ - omap_nand_switch_ecc(1, 8); - - return 0; -} -#endif - #ifndef CONFIG_SPL_BUILD #if defined(BOARD_DFU_BUTTON_GPIO) /* diff --git a/board/siemens/common/factoryset.c b/board/siemens/common/factoryset.c index be0091d1334..7baac3dda6d 100644 --- a/board/siemens/common/factoryset.c +++ b/board/siemens/common/factoryset.c @@ -220,15 +220,6 @@ int factoryset_read_eeprom(int i2c_addr) printf("DFU USB: VID = 0x%4x, PID = 0x%4x\n", factory_dat.usb_vendor_id, factory_dat.usb_product_id); #endif - if (0 <= get_factory_record_val(cp, size, (uchar *)"DEV", - (uchar *)"id", buf, - MAX_STRING_LENGTH)) { - if (strncmp((const char *)buf, "PXM50", 5) == 0) - factory_dat.pxm50 = 1; - else - factory_dat.pxm50 = 0; - } - debug("PXM50: %d\n", factory_dat.pxm50); #if defined(CONFIG_VIDEO) if (0 <= get_factory_record_val(cp, size, (uchar *)"DISP1", (uchar *)"name", factory_dat.disp_name, @@ -248,7 +239,14 @@ int factoryset_read_eeprom(int i2c_addr) NULL, 16); debug("version number: %d\n", factory_dat.version); } - + /* Get ASN from factory set if available */ + if (0 <= get_factory_record_val(cp, size, (uchar *)"DEV", + (uchar *)"id", factory_dat.asn, + MAX_STRING_LENGTH)) { + debug("factoryset asn: %s\n", factory_dat.asn); + } else { + factory_dat.asn[0] = 0; + } /* Get COMP/ver from factory set if available */ if (0 <= get_factory_record_val(cp, size, (uchar *)"COMP", (uchar *)"ver", diff --git a/board/siemens/common/factoryset.h b/board/siemens/common/factoryset.h index 7667b96b532..3f23d5ebf41 100644 --- a/board/siemens/common/factoryset.h +++ b/board/siemens/common/factoryset.h @@ -20,6 +20,7 @@ struct factorysetcontainer { #endif unsigned char serial[MAX_STRING_LENGTH]; int version; + uchar asn[MAX_STRING_LENGTH]; uchar comp_version[MAX_STRING_LENGTH]; }; diff --git a/board/siemens/draco/board.c b/board/siemens/draco/board.c index 9be2e344f8d..ede73baf3e9 100644 --- a/board/siemens/draco/board.c +++ b/board/siemens/draco/board.c @@ -280,4 +280,13 @@ U_BOOT_CMD( #endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */ #endif /* #if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) */ +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + omap_nand_switch_ecc(1, 8); + + return 0; +} +#endif + #include "../common/board.c" diff --git a/board/siemens/pxm2/board.c b/board/siemens/pxm2/board.c index 559af0e0e52..264ba025b70 100644 --- a/board/siemens/pxm2/board.c +++ b/board/siemens/pxm2/board.c @@ -428,4 +428,38 @@ static int board_video_init(void) return 0; } #endif + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + int ret; + + omap_nand_switch_ecc(1, 8); + +#ifdef CONFIG_FACTORYSET + if (factory_dat.asn[0] != 0) { + char tmp[2 * MAX_STRING_LENGTH + 2]; + + if (strncmp((const char *)factory_dat.asn, "PXM50", 5) == 0) + factory_dat.pxm50 = 1; + else + factory_dat.pxm50 = 0; + sprintf(tmp, "%s_%s", factory_dat.asn, + factory_dat.comp_version); + ret = setenv("boardid", tmp); + if (ret) + printf("error setting board id\n"); + } else { + factory_dat.pxm50 = 1; + ret = setenv("boardid", "PXM50_1.0"); + if (ret) + printf("error setting board id\n"); + } + debug("PXM50: %d\n", factory_dat.pxm50); +#endif + + return 0; +} +#endif + #include "../common/board.c" diff --git a/board/siemens/rut/board.c b/board/siemens/rut/board.c index 1752df2c4fb..fb840f7ed22 100644 --- a/board/siemens/rut/board.c +++ b/board/siemens/rut/board.c @@ -467,4 +467,27 @@ static int board_video_init(void) return 0; } #endif /* ifdef CONFIG_VIDEO */ + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + int ret; + char tmp[2 * MAX_STRING_LENGTH + 2]; + + omap_nand_switch_ecc(1, 8); + + if (factory_dat.asn[0] != 0) + sprintf(tmp, "%s_%s", factory_dat.asn, + factory_dat.comp_version); + else + sprintf(tmp, "QMX7.E38_4.0"); + + ret = setenv("boardid", tmp); + if (ret) + printf("error setting board id\n"); + + return 0; +} +#endif + #include "../common/board.c" diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index d75d5629639..946b2c85e9d 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -150,4 +150,8 @@ #define CONFIG_SYS_CONSOLE_FG_COL 0x00 #endif +#ifndef CONFIG_SPL_BUILD +#define CONFIG_FIT +#endif + #endif /* ! __CONFIG_PXM2_H */ diff --git a/include/configs/rut.h b/include/configs/rut.h index 6bddededaeb..0067ea46e0c 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -154,4 +154,8 @@ #define CONFIG_SYS_CONSOLE_FG_COL 0x00 #endif +#ifndef CONFIG_SPL_BUILD +#define CONFIG_FIT +#endif + #endif /* ! __CONFIG_RUT_H */ -- cgit v1.3.1