From 373ee048a8bdc3291aa88b93da183a0bc3b34a22 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:04:58 +0100 Subject: ARM: IXP: Remove actux1 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- include/configs/actux1.h | 226 ----------------------------------------------- 1 file changed, 226 deletions(-) delete mode 100644 include/configs/actux1.h (limited to 'include') diff --git a/include/configs/actux1.h b/include/configs/actux1.h deleted file mode 100644 index 9b8bd78943f..00000000000 --- a/include/configs/actux1.h +++ /dev/null @@ -1,226 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-1 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX1 1 - -#define CONFIG_MACH_TYPE 1479 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux1/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include - -#define CONFIG_CMD_ELF -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113842 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#ifdef CONFIG_RAM_32MB -# define CONFIG_SYS_SDR_CONFIG 0x18 -# define PHYS_SDRAM_1_SIZE 0x02000000 -# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -# define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -# define CONFIG_SYS_DRAM_SIZE 0x02000000 -#else /* 16MB SDRAM */ -# define CONFIG_SYS_SDR_CONFIG 0x3A -# define PHYS_SDRAM_1_SIZE 0x01000000 -# define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -# define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -# define CONFIG_SYS_DRAM_SIZE 0x01000000 -#endif - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#ifdef CONFIG_FLASH2X2 -# define CONFIG_SYS_MAX_FLASH_BANKS 2 -/* max number of sectors on one chip */ -# define CONFIG_SYS_MAX_FLASH_SECT 40 -# define PHYS_FLASH_1 0x50000000 -# define PHYS_FLASH_2 0x50200000 -# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } -#endif -#ifdef CONFIG_FLASH1X8 -# define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -# define CONFIG_SYS_MAX_FLASH_SECT 140 -# define PHYS_FLASH_1 0x50000000 -# define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } -#endif - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0 -/* NPE1 PHY address (HW Release E only) */ -#define CONFIG_PHY1_ADDR 1 -/* MII PHY management */ -#define CONFIG_MII 1 -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 - -#define CONFIG_HAS_ETH1 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux1/uImage\0" \ - "rootfile=actux1/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux1/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ -- cgit v1.3.1 From 13e0ee7f9acf6f1af0db7147ea8d157668f45ca6 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:06:45 +0100 Subject: ARM: IXP: Remove actux2 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux2/Makefile | 8 -- board/actux2/actux2.c | 122 ---------------------------- board/actux2/actux2_hw.h | 43 ---------- board/actux2/u-boot.lds | 99 ----------------------- boards.cfg | 1 - doc/README.scrapyard | 1 + include/configs/actux2.h | 206 ----------------------------------------------- 7 files changed, 1 insertion(+), 479 deletions(-) delete mode 100644 board/actux2/Makefile delete mode 100644 board/actux2/actux2.c delete mode 100644 board/actux2/actux2_hw.h delete mode 100644 board/actux2/u-boot.lds delete mode 100644 include/configs/actux2.h (limited to 'include') diff --git a/board/actux2/Makefile b/board/actux2/Makefile deleted file mode 100644 index 24cbff1b473..00000000000 --- a/board/actux2/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux2.o diff --git a/board/actux2/actux2.c b/board/actux2/actux2.c deleted file mode 100644 index e578cd09964..00000000000 --- a/board/actux2/actux2.c +++ /dev/null @@ -1,122 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include - -#include - -#include "actux2_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HW release register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX2_LED1(1); - ACTUX2_LED2(0); - ACTUX2_LED3(0); - ACTUX2_LED4(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-2 rev."); - putc(ACTUX2_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX2_BOARDREL; -} - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE0", 29, 31, 0x175C); -} diff --git a/board/actux2/actux2_hw.h b/board/actux2/actux2_hw.h deleted file mode 100644 index 57c6fa7076e..00000000000 --- a/board/actux2/actux2_hw.h +++ /dev/null @@ -1,43 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX2_HW_H -#define _ACTUX2_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX2_LED1(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX2_LED2(a) writeb((a ? 2 : 0), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX2_LED3(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX2_LED4(a) writeb((a ? 0 : 2), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) - -#define ACTUX2_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX2_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX2_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_UNUSED4 4 -#define CONFIG_SYS_GPIO_UNUSED5 5 -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_IPAC_INT 8 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds deleted file mode 100644 index f00d7c72b1f..00000000000 --- a/board/actux2/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux2/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/boards.cfg b/boards.cfg index b3faeb4c455..d3ebb4f58b5 100644 --- a/boards.cfg +++ b/boards.cfg @@ -377,7 +377,6 @@ Active arm armv7:arm720t tegra20 toradex colibri_t20_iris Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel Active arm armv7:arm720t tegra30 nvidia beaver beaver - Tom Warren :Stephen Warren Active arm armv7:arm720t tegra30 nvidia cardhu cardhu - Tom Warren -Active arm ixp - - - actux2 - Michael Schwingen Active arm ixp - - - actux3 - Michael Schwingen Active arm ixp - - - actux4 - Michael Schwingen Active arm ixp - - - dvlhost - Michael Schwingen diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 0ae5e4de3f8..0ac90a97bac 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +actux2 arm ixp - 2014-01-28 Michael Schwingen actux1 arm ixp - 2014-01-28 Michael Schwingen mx1ads arm arm920t - 2014-01-13 mini2440 arm arm920t - 2014-01-13 Gabriel Huau diff --git a/include/configs/actux2.h b/include/configs/actux2.h deleted file mode 100644 index f0cbff79cae..00000000000 --- a/include/configs/actux2.h +++ /dev/null @@ -1,206 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX2 1 - -#define CONFIG_MACH_TYPE 1480 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux2/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include - -#define CONFIG_CMD_ELF -#undef CONFIG_CMD_PCI -#undef CONFIG_PCI - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113042 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 16MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x3A -#define PHYS_SDRAM_1_SIZE 0x01000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x01000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x00 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux2/uImage\0" \ - "rootfile=actux2/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux2/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ -- cgit v1.3.1 From 38da33f3c1fabeb0350c1bd0ed28556802cc7c12 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:08:10 +0100 Subject: ARM: IXP: Remove actux3 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux3/Makefile | 8 -- board/actux3/actux3.c | 149 ---------------------------------- board/actux3/actux3_hw.h | 44 ---------- board/actux3/u-boot.lds | 99 ----------------------- boards.cfg | 1 - doc/README.scrapyard | 1 + include/configs/actux3.h | 205 ----------------------------------------------- 7 files changed, 1 insertion(+), 506 deletions(-) delete mode 100644 board/actux3/Makefile delete mode 100644 board/actux3/actux3.c delete mode 100644 board/actux3/actux3_hw.h delete mode 100644 board/actux3/u-boot.lds delete mode 100644 include/configs/actux3.h (limited to 'include') diff --git a/board/actux3/Makefile b/board/actux3/Makefile deleted file mode 100644 index f628f264495..00000000000 --- a/board/actux3/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux3.o diff --git a/board/actux3/actux3.c b/board/actux3/actux3.c deleted file mode 100644 index 09c803ccd4e..00000000000 --- a/board/actux3/actux3.c +++ /dev/null @@ -1,149 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include "actux3_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: IPAC-X */ - writel(0x94d10013, IXP425_EXP_CS1); - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: Release/Option register */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_ETHRST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DCD); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED6_GN); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_ETHRST); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_DSR); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DCD); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED5_GN); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_RT); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_LED6_GN); - - /* - * Setup GPIO's for Interrupt inputs - */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_DBGINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_ETHINT); - - /* - * Setup GPIO's for 33MHz clock output - */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - /* we need a minimum PCI reset pulse width after enabling the clock */ - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_ETHRST); - - ACTUX3_LED1_RT(1); - ACTUX3_LED1_GN(0); - ACTUX3_LED2_RT(0); - ACTUX3_LED2_GN(0); - ACTUX3_LED3_RT(0); - ACTUX3_LED3_GN(0); - ACTUX3_LED4_GN(0); - ACTUX3_LED5_RT(0); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-3 rev."); - putc(ACTUX3_BOARDREL + 'A' - 1); - - if (i > 0) { - puts (", serial# "); - puts (buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX3_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -void reset_phy(void) -{ - int i; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - /* all LED outputs = Link/Act */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 0x16, 0x0AAA); - - /* - * The Marvell 88E6060 switch comes up with all ports disabled. - * set all ethernet switch ports to forwarding state - */ - for (i = 1; i <= 5; i++) - miiphy_write("NPE0", CONFIG_PHY_ADDR + 8 + i, 0x04, 0x03); - -} diff --git a/board/actux3/actux3_hw.h b/board/actux3/actux3_hw.h deleted file mode 100644 index f8acb4d0604..00000000000 --- a/board/actux3/actux3_hw.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-3 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX3_HW_H -#define _ACTUX3_HW_H - -/* 0 = LED off,1 = ON */ -#define ACTUX3_LED1_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX3_LED1_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX3_LED2_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX3_LED2_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX3_LED3_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX3_LED3_GN(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX3_LED4_GN(a) writeb((a)^1, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX3_LED5_RT(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) - -#define ACTUX3_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX3_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) -#define ACTUX3_OPTION (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0xF0) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_DBGINT 0 -#define CONFIG_SYS_GPIO_ETHINT 1 -#define CONFIG_SYS_GPIO_ETHRST 2 /* Out */ -#define CONFIG_SYS_GPIO_LED5_GN 3 /* Out */ -#define CONFIG_SYS_GPIO_LED6_RT 4 /* Out */ -#define CONFIG_SYS_GPIO_LED6_GN 5 /* Out */ -#define CONFIG_SYS_GPIO_DSR 6 /* Out */ -#define CONFIG_SYS_GPIO_DCD 7 /* Out */ -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds deleted file mode 100644 index 2de3ca60b58..00000000000 --- a/board/actux3/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux3/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/boards.cfg b/boards.cfg index d3ebb4f58b5..ab94887666e 100644 --- a/boards.cfg +++ b/boards.cfg @@ -377,7 +377,6 @@ Active arm armv7:arm720t tegra20 toradex colibri_t20_iris Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel Active arm armv7:arm720t tegra30 nvidia beaver beaver - Tom Warren :Stephen Warren Active arm armv7:arm720t tegra30 nvidia cardhu cardhu - Tom Warren -Active arm ixp - - - actux3 - Michael Schwingen Active arm ixp - - - actux4 - Michael Schwingen Active arm ixp - - - dvlhost - Michael Schwingen Active arm pxa - - - balloon3 - Marek Vasut diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 0ac90a97bac..2e64278da0a 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +actux3 arm ixp - 2014-01-28 Michael Schwingen actux2 arm ixp - 2014-01-28 Michael Schwingen actux1 arm ixp - 2014-01-28 Michael Schwingen mx1ads arm arm920t - 2014-01-13 diff --git a/include/configs/actux3.h b/include/configs/actux3.h deleted file mode 100644 index 763910745ce..00000000000 --- a/include/configs/actux3.h +++ /dev/null @@ -1,205 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-3 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX3 1 - -#define CONFIG_MACH_TYPE 1481 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/actux3/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include - -#define CONFIG_CMD_ELF - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 -#define CONFIG_REVISION_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113442 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 16MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x3A -#define PHYS_SDRAM_1_SIZE 0x01000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x01000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x10 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=actux3/uImage\0" \ - "rootfile=actux3/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux3/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ -- cgit v1.3.1 From 6ff7aafa4b1f3a3f3808c9a9d9257f13e880689b Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:09:01 +0100 Subject: ARM: IXP: Remove actux4 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux4/Makefile | 8 -- board/actux4/actux4.c | 129 ------------------------------ board/actux4/actux4_hw.h | 33 -------- boards.cfg | 1 - doc/README.scrapyard | 1 + include/configs/actux4.h | 204 ----------------------------------------------- 6 files changed, 1 insertion(+), 375 deletions(-) delete mode 100644 board/actux4/Makefile delete mode 100644 board/actux4/actux4.c delete mode 100644 board/actux4/actux4_hw.h delete mode 100644 include/configs/actux4.h (limited to 'include') diff --git a/board/actux4/Makefile b/board/actux4/Makefile deleted file mode 100644 index b949b608c66..00000000000 --- a/board/actux4/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux4.o diff --git a/board/actux4/actux4.c b/board/actux4/actux4.c deleted file mode 100644 index 81c545884eb..00000000000 --- a/board/actux4/actux4.c +++ /dev/null @@ -1,129 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "actux4_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - writel(0xbd113c42, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_nPWRON); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_nPWRON); - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* led not populated on board*/ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED3); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED3); - - /* middle LED */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_LED2); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED2); - - /* right LED */ - /* weak pulldown = LED weak on */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_LED1); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_LED1); - - /* Setup GPIO's for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTB); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_USBINTC); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_RTCINT); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI_INTB); - - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTB); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_USBINTC); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_RTCINT); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI_INTB); - - /* Setup GPIO's for 33MHz clock output */ - writel(0x011001FF, IXP425_GPIO_GPCLKR); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - udelay(10000); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - puts("Board: AcTux-4\n"); - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -/* - * Hardcoded flash setup: - * Flash 0 is a non-CFI SST 39VF020 flash, 8 bit flash / 8 bit bus. - * Flash 1 is an Intel *16 flash using the CFI driver. - */ -ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info) -{ - if (banknum == 0) { /* non-CFI boot flash */ - info->portwidth = 1; - info->chipwidth = 1; - info->interface = FLASH_CFI_X8; - return 1; - } else - return 0; -} diff --git a/board/actux4/actux4_hw.h b/board/actux4/actux4_hw.h deleted file mode 100644 index b936376de9d..00000000000 --- a/board/actux4/actux4_hw.h +++ /dev/null @@ -1,33 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-4 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX4_HW_H -#define _ACTUX4_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_USBINTA 0 -#define CONFIG_SYS_GPIO_USBINTB 1 -#define CONFIG_SYS_GPIO_USBINTC 2 -#define CONFIG_SYS_GPIO_nPWRON 3 /* Out */ -#define CONFIG_SYS_GPIO_I2C_SCL 4 -#define CONFIG_SYS_GPIO_I2C_SDA 5 -#define CONFIG_SYS_GPIO_PCI_INTB 6 -#define CONFIG_SYS_GPIO_BUTTON1 7 -#define CONFIG_SYS_GPIO_LED1 8 /* Out */ -#define CONFIG_SYS_GPIO_RTCINT 9 -#define CONFIG_SYS_GPIO_LED2 10 /* Out */ -#define CONFIG_SYS_GPIO_PCI_INTA 11 -#define CONFIG_SYS_GPIO_IORST 12 /* Out */ -#define CONFIG_SYS_GPIO_LED3 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/boards.cfg b/boards.cfg index ab94887666e..2d810eefe08 100644 --- a/boards.cfg +++ b/boards.cfg @@ -377,7 +377,6 @@ Active arm armv7:arm720t tegra20 toradex colibri_t20_iris Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel Active arm armv7:arm720t tegra30 nvidia beaver beaver - Tom Warren :Stephen Warren Active arm armv7:arm720t tegra30 nvidia cardhu cardhu - Tom Warren -Active arm ixp - - - actux4 - Michael Schwingen Active arm ixp - - - dvlhost - Michael Schwingen Active arm pxa - - - balloon3 - Marek Vasut Active arm pxa - - - h2200 - Lukasz Dalek diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 2e64278da0a..2ec2ad4bdb0 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +actux4 arm ixp - 2014-01-28 Michael Schwingen actux3 arm ixp - 2014-01-28 Michael Schwingen actux2 arm ixp - 2014-01-28 Michael Schwingen actux1 arm ixp - 2014-01-28 Michael Schwingen diff --git a/include/configs/actux4.h b/include/configs/actux4.h deleted file mode 100644 index 12bd98a7e18..00000000000 --- a/include/configs/actux4.h +++ /dev/null @@ -1,204 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the AcTux-4 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_ACTUX4 1 - -#define CONFIG_MACH_TYPE 1532 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration */ -#include - -#define CONFIG_CMD_ELF - -#define CONFIG_PCI -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00400000 -#define CONFIG_SYS_MEMTEST_END 0x00800000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66000000 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113003 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 32MB SDRAM */ -#define CONFIG_SYS_SDR_CONFIG 0x18 -#define PHYS_SDRAM_1_SIZE 0x02000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE 0x02000000 - -/* FLASH organization */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 -/* max # of sectors per chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 70 -#define PHYS_FLASH_1 0x50000000 -#define PHYS_FLASH_2 0x51000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (252 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 258048 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* board provides its own flash_init code */ -#define CONFIG_FLASH_CFI_LEGACY 1 -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -/* SST 39VF020 etc. support */ -#define CONFIG_SYS_FLASH_LEGACY_256Kx8 1 - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY address */ -#define CONFIG_PHY_ADDR 0x1C -/* MII PHY management */ -#define CONFIG_MII 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* environment organization: one complete 4k flash sector */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x3f000) - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=51000000\0" \ - "mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \ - "IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \ - "kerneladdr=51020000\0" \ - "kernelfile=actux4/uImage\0" \ - "rootfile=actux4/rootfs\0" \ - "rootaddr=51160000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} actux4/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 5003efff;" \ - " erase 50000000 +${filesize}\0" \ - "writeboot=cp.b 10000 50000000 ${filesize}\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock4" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ -- cgit v1.3.1 From e317de6b083adee81187fe1bba8b2fdf0ac983e7 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:10:46 +0100 Subject: ARM: IXP: Remove dvl_host board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/dvlhost/Makefile | 8 -- board/dvlhost/dvlhost.c | 112 ----------------------- board/dvlhost/dvlhost_hw.h | 31 ------- board/dvlhost/u-boot.lds | 99 -------------------- board/dvlhost/watchdog.c | 27 ------ boards.cfg | 1 - doc/README.scrapyard | 1 + include/configs/dvlhost.h | 222 --------------------------------------------- 8 files changed, 1 insertion(+), 500 deletions(-) delete mode 100644 board/dvlhost/Makefile delete mode 100644 board/dvlhost/dvlhost.c delete mode 100644 board/dvlhost/dvlhost_hw.h delete mode 100644 board/dvlhost/u-boot.lds delete mode 100644 board/dvlhost/watchdog.c delete mode 100644 include/configs/dvlhost.h (limited to 'include') diff --git a/board/dvlhost/Makefile b/board/dvlhost/Makefile deleted file mode 100644 index 8b489362cea..00000000000 --- a/board/dvlhost/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := dvlhost.o watchdog.o diff --git a/board/dvlhost/dvlhost.c b/board/dvlhost/dvlhost.c deleted file mode 100644 index 087070f40d1..00000000000 --- a/board/dvlhost/dvlhost.c +++ /dev/null @@ -1,112 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS1: LED Latch */ - writel(0xBFFF0002, IXP425_EXP_CS1); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - /* Setup GPIOs used as output */ - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_PCIRST); - - /* - * LED latch enable and watchdog enable are tied to the same GPIO, - * so we need to trigger the watchdog if we want to enable the LEDs. - */ -#ifdef CONFIG_HW_WATCHDOG - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_WDG_LED_EN); -#else - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_WDG_LED_EN); -#endif - - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDGTRIGGER); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_DLAN_PAIRING); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_WDG_LED_EN); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCIRST); - - /* Setup GPIOs for Interrupt inputs */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_WLAN); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_PAIRING); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_BTN_RESET); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQA); - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_IRQB); - - /* Setup GPIO's for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x01FF01FF, IXP425_GPIO_GPCLKR); - - /* turn off all LEDs */ - writew(0x0000, DVLHOST_LED_LATCH); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_PCIRST); - - return 0; -} - -/* Check Board Identity */ -int checkboard(void) -{ - char *s = getenv("serial#"); - - puts("Board: dLAN 200AV (dvlhost)"); - - if (s != NULL) { - puts(", serial# "); - puts(s); - } - putc('\n'); - - return 0; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - /* init IcPlus IP175C ethernet switch to native IP175C mode */ - miiphy_write("NPE1", 29, 31, 0x175C); -} diff --git a/board/dvlhost/dvlhost_hw.h b/board/dvlhost/dvlhost_hw.h deleted file mode 100644 index 545099e9ea6..00000000000 --- a/board/dvlhost/dvlhost_hw.h +++ /dev/null @@ -1,31 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the - * dLAN200 AV Wireless G ("dvlhost") board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _DVLHOST_HW_H -#define _DVLHOST_HW_H - -/* - * GPIO settings - */ -#define CONFIG_SYS_GPIO_WDGTRIGGER 0 /* Out */ -#define CONFIG_SYS_GPIO_BTN_WLAN 1 -#define CONFIG_SYS_GPIO_BTN_PAIRING 6 -#define CONFIG_SYS_GPIO_DLAN_PAIRING 7 /* Out */ -#define CONFIG_SYS_GPIO_BTN_RESET 9 -#define CONFIG_SYS_GPIO_IRQB 10 -#define CONFIG_SYS_GPIO_IRQA 11 -#define CONFIG_SYS_GPIO_WDG_LED_EN 12 /* Out */ -#define CONFIG_SYS_GPIO_PCIRST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#define DVLHOST_LED_LATCH IXP425_EXP_BUS_CS1_BASE_PHYS - -#endif diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds deleted file mode 100644 index ebcaf447b83..00000000000 --- a/board/dvlhost/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/dvlhost/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/serial/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN (4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN (4); - .data : { - *(.data*) - } - . = ALIGN (4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/board/dvlhost/watchdog.c b/board/dvlhost/watchdog.c deleted file mode 100644 index 02ec35eb1a9..00000000000 --- a/board/dvlhost/watchdog.c +++ /dev/null @@ -1,27 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include "dvlhost_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -#ifdef CONFIG_HW_WATCHDOG -#include -#include - -void hw_watchdog_reset(void) -{ - unsigned int x; - x = readl(IXP425_GPIO_GPOUTR); - x ^= (1 << (CONFIG_SYS_GPIO_WDGTRIGGER)); - writel(x, IXP425_GPIO_GPOUTR); -} - -#endif /* CONFIG_HW_WATCHDOG */ diff --git a/boards.cfg b/boards.cfg index 2d810eefe08..de11dfe2938 100644 --- a/boards.cfg +++ b/boards.cfg @@ -377,7 +377,6 @@ Active arm armv7:arm720t tegra20 toradex colibri_t20_iris Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel Active arm armv7:arm720t tegra30 nvidia beaver beaver - Tom Warren :Stephen Warren Active arm armv7:arm720t tegra30 nvidia cardhu cardhu - Tom Warren -Active arm ixp - - - dvlhost - Michael Schwingen Active arm pxa - - - balloon3 - Marek Vasut Active arm pxa - - - h2200 - Lukasz Dalek Active arm pxa - - - palmld - Marek Vasut diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 2ec2ad4bdb0..6b41445faa0 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +dvl_host arm ixp - 2014-01-28 Michael Schwingen actux4 arm ixp - 2014-01-28 Michael Schwingen actux3 arm ixp - 2014-01-28 Michael Schwingen actux2 arm ixp - 2014-01-28 Michael Schwingen diff --git a/include/configs/dvlhost.h b/include/configs/dvlhost.h deleted file mode 100644 index 1af7f169893..00000000000 --- a/include/configs/dvlhost.h +++ /dev/null @@ -1,222 +0,0 @@ -/* - * (C) Copyright 2009 - * Michael Schwingen, michael@schwingen.org - * - * Configuration settings for the - * dLAN200 AV Wireless G ("dvlhost") board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_IXP425 1 -#define CONFIG_DVLHOST 1 - -#define CONFIG_MACH_TYPE 1343 - -#define CONFIG_DISPLAY_CPUINFO 1 -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_IXP_SERIAL -#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART2 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 3 -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_BOARD_EARLY_INIT_F 1 -#define CONFIG_SYS_LDSCRIPT "board/dvlhost/u-boot.lds" - -/*************************************************************** - * U-boot generic defines start here. - ***************************************************************/ -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* Command line configuration. */ -#include - -#define CONFIG_CMD_ELF -#define CONFIG_PCI -#ifdef CONFIG_PCI -#define CONFIG_CMD_PCI -#define CONFIG_PCI_PNP -#define CONFIG_IXP_PCI -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_CMD_PCI_ENUM -#endif - -#define CONFIG_BOOTCOMMAND "run boot_flash" -/* enable passing of ATAGs */ -#define CONFIG_CMDLINE_TAG 1 -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_KGDB_BAUDRATE 230400 -#endif - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00000000 -#define CONFIG_SYS_MEMTEST_END 0x01D80000 - -/* timer clock - 2* OSC_IN system clock */ -#define CONFIG_IXP425_TIMER_CLK 66666666 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x00010000 - -/* valid baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200, 230400 } -#define CONFIG_SERIAL_RTS_ACTIVE 1 - -/* Expansion bus settings */ -#define CONFIG_SYS_EXP_CS0 0xbd113442 - -/* SDRAM settings */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 0x00000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* 32MB SDRAM: 2* 8Mx16, CL3 */ -#define CONFIG_SYS_SDR_CONFIG 0x18 -#define PHYS_SDRAM_1_SIZE 0x02000000 -#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x800 -#define CONFIG_SYS_SDR_MODE_CONFIG 0x1 -#define CONFIG_SYS_DRAM_SIZE PHYS_SDRAM_1_SIZE - -/* FLASH organization: one Spansion S29AL032D-04 Flash */ -#define CONFIG_SYS_TEXT_BASE 0x50000000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 140 -#define PHYS_FLASH_1 0x50000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 } - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) -#define CONFIG_BOARD_SIZE_LIMIT 262144 - -/* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -/* no byte writes on IXP4xx */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* Ethernet */ - -/* include IXP4xx NPE support */ -#define CONFIG_IXP4XX_NPE 1 - -/* NPE0 PHY: MII dLAN200 AVmodule, 100BaseT-FDX fixed */ -#define CONFIG_PHY_ADDR 0x18 -/* NPE1 PHY: MII IP175 switch, port 5 is host port */ -#define CONFIG_PHY1_ADDR 0x05 -/* MII PHY management */ -#define CONFIG_MII 1 -/* fixed-speed powerline modem without standard PHY registers on MII */ -#define CONFIG_MII_NPE0_FIXEDLINK 1 -#define CONFIG_MII_NPE0_SPEED 100 -#define CONFIG_MII_NPE0_FULLDUPLEX 1 -/* fixed-speed switch without standard PHY registers on MII */ -#define CONFIG_MII_NPE1_FIXEDLINK 1 -#define CONFIG_MII_NPE1_SPEED 100 -#define CONFIG_MII_NPE1_FULLDUPLEX 1 - -/* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SYS_RX_ETH_BUFFER 16 -#define CONFIG_RESET_PHY_R 1 -/* ethernet switch connected to MII port */ -#define CONFIG_MII_ETHSWITCH 1 -#define CONFIG_HAS_ETH1 1 - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#undef CONFIG_CMD_NFS - -/* BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* Cache Configuration */ -#define CONFIG_SYS_CACHELINE_SIZE 32 - -/* - * environment organization: - * one flash sector, embedded in uboot area (bottom bootblock flash) - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x4000) -#define CONFIG_SYS_USE_PPCENV 1 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "npe_ucode=50040000\0" \ - "ethprime=NPE1\0" \ - "ethrotate=no\0" \ - "mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root),\0" \ - "kerneladdr=50050000\0" \ - "kernelfile=dvlhost/uImage\0" \ - "rootfile=dvlhost/rootfs\0" \ - "rootaddr=50170000\0" \ - "loadaddr=10000\0" \ - "updateboot_ser=mw.b 10000 ff 40000;" \ - " loady ${loadaddr};" \ - " run eraseboot writeboot\0" \ - "updateboot_net=mw.b 10000 ff 40000;" \ - " tftp ${loadaddr} dvlhost/u-boot.bin;" \ - " run eraseboot writeboot\0" \ - "eraseboot=protect off 50000000 50003fff;" \ - " protect off 50006000 5003ffff;" \ - " erase 50000000 50003fff;" \ - " erase 50006000 5003ffff\0" \ - "writeboot=cp.b 10000 50000000 4000;" \ - " cp.b 16000 50006000 3a000\0" \ - "updateucode=loady;" \ - " era ${npe_ucode} +${filesize};" \ - " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \ - "updateroot=tftp ${loadaddr} ${rootfile};" \ - " era ${rootaddr} +${filesize};" \ - " cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \ - "updatekern=tftp ${loadaddr} ${kernelfile};" \ - " era ${kerneladdr} +${filesize};" \ - " cp.b ${loadaddr} ${kerneladdr} ${filesize}\0" \ - "flashargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "netargs=setenv bootargs mtdparts=${mtd} root=/dev/mtdblock3" \ - " rootfstype=squashfs,jffs2 init=/etc/preinit\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ - "boot_flash=run flashargs addtty addeth;" \ - " bootm ${kerneladdr}\0" \ - "boot_net=run netargs addtty addeth;" \ - " tftpboot ${loadaddr} ${kernelfile};" \ - " bootm\0" - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE) - -#endif /* __CONFIG_H */ -- cgit v1.3.1