From 566a494f592ae3b3c0785d90d4e1ba45574880c4 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Fri, 22 Jun 2007 19:11:54 +0200 Subject: [PCS440EP] upgrade the PCS440EP board: - Show on the Status LEDs, some States of the board. - Get the MAC addresses from the EEProm - use PREBOOT - use the CF on the board. - check the U-Boot image in the Flash with a SHA1 checksum. - use dynamic TLB entries generation for the SDRAM Signed-off-by: Heiko Schocher --- include/configs/pcs440ep.h | 83 ++++++++++++++++++++++++++++++-- include/sha1.h | 115 +++++++++++++++++++++++++++++++++++++++++++++ include/status_led.h | 7 +++ 3 files changed, 202 insertions(+), 3 deletions(-) create mode 100644 include/sha1.h (limited to 'include') diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index 23bdfc8dfb9..d4718088213 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -105,19 +105,27 @@ #ifdef CFG_ENV_IS_IN_FLASH #define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ #define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +#define CONFIG_ENV_OVERWRITE 1 /* Address and size of Redundant Environment Sector */ #define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #endif /* CFG_ENV_IS_IN_FLASH */ +#define ENV_NAME_REVLEV "revision_level" +#define ENV_NAME_SOLDER "solder_switch" +#define ENV_NAME_DIP "dip" + /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */ #undef CONFIG_DDR_ECC /* don't use ECC */ #define SPD_EEPROM_ADDRESS {0x50} +#define CONFIG_PROG_SDRAM_TLB 1 +#define CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG 1 /*----------------------------------------------------------------------- * I2C @@ -142,6 +150,8 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "hostname=pcs440ep\0" \ + "use_eeprom_ethaddr=default\0" \ + "cs_test=off\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -172,6 +182,36 @@ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ #endif +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +/* check U-Boot image with SHA1 sum */ +#define CONFIG_SHA1_CHECK_UB_IMG 1 +#define CONFIG_SHA1_START CFG_MONITOR_BASE +#define CONFIG_SHA1_LEN CFG_MONITOR_LEN + +/*----------------------------------------------------------------------- + * Definitions for status LED + */ +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED 1 + +#define STATUS_LED_BIT 0x08 /* LED 1 is on GPIO_PPC_1 */ +#define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_BIT1 0x04 /* LED 2 is on GPIO_PPC_2 */ +#define STATUS_LED_PERIOD1 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE1 STATUS_LED_ON +#define STATUS_LED_BIT2 0x02 /* LED 3 is on GPIO_PPC_3 */ +#define STATUS_LED_PERIOD2 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE2 STATUS_LED_OFF +#define STATUS_LED_BIT3 0x01 /* LED 4 is on GPIO_PPC_4 */ +#define STATUS_LED_PERIOD3 ((CFG_HZ / 2) / 5) /* blink at 5 Hz */ +#define STATUS_LED_STATE3 STATUS_LED_OFF + +#define CONFIG_SHOW_BOOT_PROGRESS 1 + #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -213,7 +253,10 @@ CFG_CMD_DIAG | \ CFG_CMD_EEPROM | \ CFG_CMD_ELF | \ + CFG_CMD_EXT2 | \ + CFG_CMD_FAT | \ CFG_CMD_I2C | \ + CFG_CMD_IDE | \ CFG_CMD_IRQ | \ CFG_CMD_MII | \ CFG_CMD_NET | \ @@ -221,9 +264,8 @@ CFG_CMD_PCI | \ CFG_CMD_PING | \ CFG_CMD_REGINFO | \ + CFG_CMD_REISER | \ CFG_CMD_SDRAM | \ - CFG_CMD_EXT2 | \ - CFG_CMD_FAT | \ CFG_CMD_USB ) @@ -410,4 +452,39 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif +/*----------------------------------------------------------------------- + * IDE/ATA stuff Supports IDE harddisk + *----------------------------------------------------------------------- + */ + +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ + +#define CONFIG_IDE_PREINIT 1 +#define CONFIG_IDE_RESET 1 + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_CF1 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET (0x0000) + +/* This addresses need to be shifted one place to the left + * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0) + * This values are shifted + */ +#define CFG_ATA_PORT_ADDR(port) ((port) << 1) + #endif /* __CONFIG_H */ diff --git a/include/sha1.h b/include/sha1.h new file mode 100644 index 00000000000..3030f2975f2 --- /dev/null +++ b/include/sha1.h @@ -0,0 +1,115 @@ +/** + * \file sha1.h + * based from http://xyssl.org/code/source/sha1/ + * FIPS-180-1 compliant SHA-1 implementation + * + * Copyright (C) 2003-2006 Christophe Devine + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Lesser General Public + * License, version 2.1 as published by the Free Software Foundation. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Lesser General Public License for more details. + * + * You should have received a copy of the GNU Lesser General Public + * License along with this library; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ +/* + * The SHA-1 standard was published by NIST in 1993. + * + * http://www.itl.nist.gov/fipspubs/fip180-1.htm + */ +#ifndef _SHA1_H +#define _SHA1_H + +#ifdef __cplusplus +extern "C" { +#endif + +#define SHA1_SUM_POS -0x20 +#define SHA1_SUM_LEN 20 + +/** + * \brief SHA-1 context structure + */ +typedef struct +{ + unsigned long total[2]; /*!< number of bytes processed */ + unsigned long state[5]; /*!< intermediate digest state */ + unsigned char buffer[64]; /*!< data block being processed */ +} +sha1_context; + +/** + * \brief SHA-1 context setup + * + * \param ctx SHA-1 context to be initialized + */ +void sha1_starts( sha1_context *ctx ); + +/** + * \brief SHA-1 process buffer + * + * \param ctx SHA-1 context + * \param input buffer holding the data + * \param ilen length of the input data + */ +void sha1_update( sha1_context *ctx, unsigned char *input, int ilen ); + +/** + * \brief SHA-1 final digest + * + * \param ctx SHA-1 context + * \param output SHA-1 checksum result + */ +void sha1_finish( sha1_context *ctx, unsigned char output[20] ); + +/** + * \brief Output = SHA-1( input buffer ) + * + * \param input buffer holding the data + * \param ilen length of the input data + * \param output SHA-1 checksum result + */ +void sha1_csum( unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Output = SHA-1( file contents ) + * + * \param path input file name + * \param output SHA-1 checksum result + * \return 0 if successful, or 1 if fopen failed + */ +int sha1_file( char *path, unsigned char output[20] ); + +/** + * \brief Output = HMAC-SHA-1( input buffer, hmac key ) + * + * \param key HMAC secret key + * \param keylen length of the HMAC key + * \param input buffer holding the data + * \param ilen length of the input data + * \param output HMAC-SHA-1 result + */ +void sha1_hmac( unsigned char *key, int keylen, + unsigned char *input, int ilen, + unsigned char output[20] ); + +/** + * \brief Checkup routine + * + * \return 0 if successful, or 1 if the test failed + */ +int sha1_self_test( void ); + +#ifdef __cplusplus +} +#endif + +#endif /* sha1.h */ diff --git a/include/status_led.h b/include/status_led.h index 71a202fe36e..a6468142557 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -367,6 +367,13 @@ void status_led_set (int led, int state); #define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ +#elif defined(CONFIG_BOARD_SPECIFIC_LED) +/* led_id_t is unsigned long mask */ +typedef unsigned long led_id_t; + +extern void __led_toggle (led_id_t mask); +extern void __led_init (led_id_t mask, int state); +extern void __led_set (led_id_t mask, int state); #else # error Status LED configuration missing #endif -- cgit v1.3.1 From a5d71e290f3673269be8eefb4ec44f53412f9461 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Mon, 25 Jun 2007 19:11:37 +0200 Subject: [PCS440EP] get rid of CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG Signed-off-by: Heiko Schocher --- board/pcs440ep/pcs440ep.c | 3 -- cpu/ppc4xx/44x_spd_ddr.c | 32 ++++++++++--------- cpu/ppc4xx/44x_spd_ddr2.c | 79 ++++++++++++++++++++++++---------------------- include/configs/pcs440ep.h | 1 - 4 files changed, 58 insertions(+), 57 deletions(-) (limited to 'include') diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c index f638589df29..8b2427aa946 100644 --- a/board/pcs440ep/pcs440ep.c +++ b/board/pcs440ep/pcs440ep.c @@ -506,8 +506,6 @@ int checkboard(void) return (0); } - -#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) void spd_ddr_init_hang (void) { status_led_set (0, STATUS_LED_OFF); @@ -520,7 +518,6 @@ void spd_ddr_init_hang (void) udelay (100000); } } -#endif long int initdram (int board_type) { diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index 8621aa00cf4..a384392406a 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -70,12 +70,14 @@ #define ONE_BILLION 1000000000 -#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) -extern void spd_ddr_init_hang (void); -#define HANG() spd_ddr_init_hang() -#else -#define HANG() hang() -#endif +/* + * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed + */ +void __spd_ddr_init_hang (void) +{ + hang (); +} +void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang"))); /*----------------------------------------------------------------------------- | Memory Controller Options 0 @@ -474,7 +476,7 @@ static void get_spd_info(unsigned long *dimm_populated, if (dimm_found == FALSE) { printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } } @@ -497,7 +499,7 @@ static void check_mem_type(unsigned long *dimm_populated, dimm_num); printf("Only DDR SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; } } @@ -517,7 +519,7 @@ static void check_volt_type(unsigned long *dimm_populated, if (voltage_type != 0x04) { printf("ERROR: DIMM %lu with unsupported voltage level.\n", dimm_num); - HANG(); + spd_ddr_init_hang (); } else { debug("DIMM %lu voltage level supported.\n", dimm_num); } @@ -588,7 +590,7 @@ static void program_cfg0(unsigned long *dimm_populated, printf("WARNING: DIMM with datawidth of %lu bits.\n", data_width); printf("Only DIMMs with 32 or 64 bit datawidths supported.\n"); - HANG(); + spd_ddr_init_hang (); } break; } @@ -776,7 +778,7 @@ static void program_tr0(unsigned long *dimm_populated, if ((tcyc_reg & 0x0F) >= 10) { printf("ERROR: Tcyc incorrect for DIMM in slot %lu\n", dimm_num); - HANG(); + spd_ddr_init_hang (); } cycle_time_ns_x_10[cas_index] = @@ -856,7 +858,7 @@ static void program_tr0(unsigned long *dimm_populated, printf("ERROR: No supported CAS latency with the installed DIMMs.\n"); printf("Only CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); printf("Make sure the PLB speed is within the supported range.\n"); - HANG(); + spd_ddr_init_hang (); } /* @@ -1168,7 +1170,7 @@ static void program_tr1(void) */ if (window_found == FALSE) { printf("ERROR: Cannot determine a common read delay.\n"); - HANG(); + spd_ddr_init_hang (); } /* @@ -1318,7 +1320,7 @@ static unsigned long program_bxcr(unsigned long *dimm_populated, printf("ERROR: Unsupported value for the banksize: %d.\n", bank_size_id); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } switch (num_col_addr) { @@ -1340,7 +1342,7 @@ static unsigned long program_bxcr(unsigned long *dimm_populated, printf("ERROR: Unsupported value for number of " "column addresses: %d.\n", num_col_addr); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } /* diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index d748daee015..626b3e69bd9 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -129,12 +129,15 @@ #define MY_TLB_WORD2_I_ENABLE TLB_WORD2_I_ENABLE /* disable caching on SDRAM */ #endif -#if defined(CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG) -extern void spd_ddr_init_hang (void); -#define HANG() spd_ddr_init_hang() -#else -#define HANG() hang() -#endif +/* + * Board-specific Platform code can reimplement spd_ddr_init_hang () if needed + */ +void __spd_ddr_init_hang (void) +{ + hang (); +} +void spd_ddr_init_hang (void) __attribute__((weak, alias("__spd_ddr_init_hang"))); + /* Private Structure Definitions */ @@ -589,7 +592,7 @@ static void get_spd_info(unsigned long *dimm_populated, if (dimm_found == FALSE) { printf("ERROR - No memory installed. Install a DDR-SDRAM DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } } @@ -636,42 +639,42 @@ static void check_mem_type(unsigned long *dimm_populated, "slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 2: printf("ERROR: EDO DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 3: printf("ERROR: Pipelined Nibble DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 4: printf("ERROR: SDRAM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 5: printf("ERROR: Multiplexed ROM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 6: printf("ERROR: SGRAM DIMM detected in slot %d.\n", (unsigned int)dimm_num); printf("Only DDR and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; case 7: debug("DIMM slot %d: DDR1 SDRAM detected\n", dimm_num); @@ -686,7 +689,7 @@ static void check_mem_type(unsigned long *dimm_populated, (unsigned int)dimm_num); printf("Only DDR1 and DDR2 SDRAM DIMMs are supported.\n"); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; } } @@ -696,7 +699,7 @@ static void check_mem_type(unsigned long *dimm_populated, && (dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_populated[dimm_num-1] != dimm_populated[dimm_num])) { printf("ERROR: DIMM's DDR1 and DDR2 type can not be mixed.\n"); - HANG(); + spd_ddr_init_hang (); } } } @@ -771,7 +774,7 @@ static void check_frequency(unsigned long *dimm_populated, (unsigned int)(calc_cycle_time*10)); printf("Replace the DIMM, or change DDR frequency via " "strapping bits.\n\n"); - HANG(); + spd_ddr_init_hang (); } } } @@ -803,7 +806,7 @@ static void check_rank_number(unsigned long *dimm_populated, "slot %d is not supported.\n", dimm_rank, dimm_num); printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } else total_rank += dimm_rank; } @@ -812,7 +815,7 @@ static void check_rank_number(unsigned long *dimm_populated, "for all slots.\n", (unsigned int)total_rank); printf("Only %d ranks are supported for all DIMM.\n", MAXRANKS); printf("Remove one of the DIMM modules.\n\n"); - HANG(); + spd_ddr_init_hang (); } } } @@ -837,28 +840,28 @@ static void check_voltage_type(unsigned long *dimm_populated, printf("This DIMM is 5.0 Volt/TTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); break; case 0x01: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is LVTTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); break; case 0x02: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is 1.5 Volt.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); break; case 0x03: printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("This DIMM is 3.3 Volt/TTL.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); break; case 0x04: /* 2.5 Voltage only for DDR1 */ @@ -870,7 +873,7 @@ static void check_voltage_type(unsigned long *dimm_populated, printf("ERROR: Only DIMMs DDR 2.5V or DDR2 1.8V are supported.\n"); printf("Replace the DIMM module in slot %d with a supported DIMM.\n\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); break; } } @@ -1013,13 +1016,13 @@ static void program_copt1(unsigned long *dimm_populated, if ((dimm_populated[0] != SDRAM_NONE) && (dimm_populated[1] != SDRAM_NONE)) { if (buf0 != buf1) { printf("ERROR: DIMM's buffered/unbuffered, registered, clocking don't match.\n"); - HANG(); + spd_ddr_init_hang (); } } if ((dimm_64bit == TRUE) && (dimm_32bit == TRUE)) { printf("ERROR: Cannot mix 32 bit and 64 bit DDR-SDRAM DIMMs together.\n"); - HANG(); + spd_ddr_init_hang (); } else if ((dimm_64bit == TRUE) && (dimm_32bit == FALSE)) { mcopt1 |= SDRAM_MCOPT1_DMWD_64; @@ -1027,7 +1030,7 @@ static void program_copt1(unsigned long *dimm_populated, mcopt1 |= SDRAM_MCOPT1_DMWD_32; } else { printf("ERROR: Please install only 32 or 64 bit DDR-SDRAM DIMMs.\n\n"); - HANG(); + spd_ddr_init_hang (); } if (ecc_enabled == TRUE) @@ -1216,7 +1219,7 @@ static void program_initplr(unsigned long *dimm_populated, break; default: printf("ERROR: ucode error on selected_cas value %d", selected_cas); - HANG(); + spd_ddr_init_hang (); break; } @@ -1248,7 +1251,7 @@ static void program_initplr(unsigned long *dimm_populated, break; default: printf("ERROR: write recovery not support (%d)", write_recovery); - HANG(); + spd_ddr_init_hang (); break; } #else @@ -1266,7 +1269,7 @@ static void program_initplr(unsigned long *dimm_populated, ods = ODS_REDUCED; } else { printf("ERROR: Unsupported number of DIMM's (%d)", total_dimm); - HANG(); + spd_ddr_init_hang (); } mr = CMD_EMR | SELECT_MR | BURST_LEN_4 | wr | cas; @@ -1291,7 +1294,7 @@ static void program_initplr(unsigned long *dimm_populated, mtsdram(SDRAM_INITPLR13, 0x80800000 | emr); /* EMR OCD Exit */ } else { printf("ERROR: ucode error as unknown DDR type in program_initplr"); - HANG(); + spd_ddr_init_hang (); } } @@ -1396,7 +1399,7 @@ static void program_mode(unsigned long *dimm_populated, } else { printf("ERROR: SPD reported Tcyc is incorrect for DIMM " "in slot %d\n", (unsigned int)dimm_num); - HANG(); + spd_ddr_init_hang (); } } else { /* Convert from hex to decimal */ @@ -1533,7 +1536,7 @@ static void program_mode(unsigned long *dimm_populated, printf("ERROR: Cannot find a supported CAS latency with the installed DIMMs.\n"); printf("Only DIMMs DDR1 with CAS latencies of 2.0, 2.5, and 3.0 are supported.\n"); printf("Make sure the PLB speed is within the supported range of the DIMMs.\n\n"); - HANG(); + spd_ddr_init_hang (); } } else { /* DDR2 */ debug("cas_3_0_available=%d\n", cas_3_0_available); @@ -1556,7 +1559,7 @@ static void program_mode(unsigned long *dimm_populated, cas_3_0_available, cas_4_0_available, cas_5_0_available); printf("sdram_freq=%d cycle3=%d cycle4=%d cycle5=%d\n\n", sdram_freq, cycle_3_0_clk, cycle_4_0_clk, cycle_5_0_clk); - HANG(); + spd_ddr_init_hang (); } } @@ -1665,7 +1668,7 @@ static void program_rtr(unsigned long *dimm_populated, printf("ERROR: DIMM %d unsupported refresh rate/type.\n", (unsigned int)dimm_num); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); break; } @@ -2073,7 +2076,7 @@ static void program_bxcf(unsigned long *dimm_populated, printf("ERROR: Unsupported value for number of " "column addresses: %d.\n", (unsigned int)num_col_addr); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } } @@ -2155,7 +2158,7 @@ static void program_memory_queue(unsigned long *dimm_populated, printf("ERROR: Unsupported value for the banksize: %d.\n", (unsigned int)rank_size_id); printf("Replace the DIMM module with a supported DIMM.\n\n"); - HANG(); + spd_ddr_init_hang (); } if ((dimm_populated[dimm_num] != SDRAM_NONE) && (dimm_num == 1)) @@ -2700,7 +2703,7 @@ calibration_loop: printf("\nERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__); - HANG(); + spd_ddr_init_hang (); } blank_string(strlen(str)); @@ -2856,7 +2859,7 @@ static void test(void) if (window_found == FALSE) { printf("ERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); - HANG(); + spd_ddr_init_hang (); } /*------------------------------------------------------------------ diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index d4718088213..c2b5cb8f9f5 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -125,7 +125,6 @@ #undef CONFIG_DDR_ECC /* don't use ECC */ #define SPD_EEPROM_ADDRESS {0x50} #define CONFIG_PROG_SDRAM_TLB 1 -#define CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG 1 /*----------------------------------------------------------------------- * I2C -- cgit v1.3.1