From f485c8a35b38356a473208bec5ed786792c1eafe Mon Sep 17 00:00:00 2001 From: Matt Porter Date: Wed, 20 Mar 2013 05:38:13 +0000 Subject: phy: add support for ET1011C phys Adds an ET1011C PHY driver which is derived from the Linux kernel PHY driver (drivers/net/phy/et1011c.c) from the v3.9-rc2 tag. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the PG1.0 TI814X EVM. Signed-off-by: Matt Porter Reviewed-by: Tom Rini --- include/phy.h | 1 + 1 file changed, 1 insertion(+) (limited to 'include') diff --git a/include/phy.h b/include/phy.h index 58ca2730c84..7b4ce744e11 100644 --- a/include/phy.h +++ b/include/phy.h @@ -223,6 +223,7 @@ int gen10g_discover_mmds(struct phy_device *phydev); int phy_atheros_init(void); int phy_broadcom_init(void); int phy_davicom_init(void); +int phy_et1011c_init(void); int phy_lxt_init(void); int phy_marvell_init(void); int phy_micrel_init(void); -- cgit v1.3.1 From cd87464d0873d2db920e6b712ef34e9c83cfe5e6 Mon Sep 17 00:00:00 2001 From: Matt Porter Date: Wed, 20 Mar 2013 05:38:14 +0000 Subject: ti814x_evm: enable CPSW support Adds CPSW support to the TI814X EVM configured with an ET1011C PHY in GMII mode. Signed-off-by: Matt Porter Reviewed-by: Tom Rini --- board/ti/ti814x/evm.c | 72 ++++++++++++++++++++++++++++++++++++++++++++ board/ti/ti814x/evm.h | 1 + board/ti/ti814x/mux.c | 35 +++++++++++++++++++++ include/configs/ti814x_evm.h | 21 +++++++++++++ 4 files changed, 129 insertions(+) (limited to 'include') diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c index 2089a143d61..7adb52405c1 100644 --- a/board/ti/ti814x/evm.c +++ b/board/ti/ti814x/evm.c @@ -17,6 +17,7 @@ */ #include +#include #include #include #include @@ -39,6 +40,8 @@ static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; #endif +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + /* UART Defines */ #ifdef CONFIG_SPL_BUILD #define UART_RESET (0x1 << 1) @@ -166,6 +169,9 @@ void s_init(void) /* Set MMC pins */ enable_mmc1_pin_mux(); + /* Set Ethernet pins */ + enable_enet_pin_mux(); + /* Enable UART */ uart_enable(); @@ -199,3 +205,69 @@ int board_mmc_init(bd_t *bis) return 0; } #endif + +#ifdef CONFIG_DRIVER_TI_CPSW +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x50, + .sliver_reg_ofs = 0x700, + .phy_id = 1, + }, + { + .slave_reg_ofs = 0x90, + .sliver_reg_ofs = 0x740, + .phy_id = 0, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x100, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0x600, + .ale_entries = 1024, + .host_port_reg_ofs = 0x28, + .hw_stats_reg_ofs = 0x400, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_1, +}; +#endif + +int board_eth_init(bd_t *bis) +{ + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { + printf(" not set. Reading from E-fuse\n"); + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + else + printf("Unable to read MAC address. Set \n"); + } + + return cpsw_register(&cpsw_data); +} diff --git a/board/ti/ti814x/evm.h b/board/ti/ti814x/evm.h index 40f8710c896..6aebec62d4a 100644 --- a/board/ti/ti814x/evm.h +++ b/board/ti/ti814x/evm.h @@ -3,5 +3,6 @@ void enable_uart0_pin_mux(void); void enable_mmc1_pin_mux(void); +void enable_enet_pin_mux(void); #endif /* _EVM_H */ diff --git a/board/ti/ti814x/mux.c b/board/ti/ti814x/mux.c index 137acb45233..fd9f3645115 100644 --- a/board/ti/ti814x/mux.c +++ b/board/ti/ti814x/mux.c @@ -40,6 +40,36 @@ static struct module_pin_mux mmc1_pin_mux[] = { {-1}, }; +static struct module_pin_mux enet_pin_mux[] = { + {OFFSET(pincntl232), MODE(0x01)}, /* EMAC_RMREFCLK */ + {OFFSET(pincntl233), PULLUP_EN | MODE(0x01)}, /* MDCLK */ + {OFFSET(pincntl234), PULLUP_EN | MODE(0x01)}, /* MDIO */ + {OFFSET(pincntl235), MODE(0x01)}, /* EMAC[0]_MTCLK */ + {OFFSET(pincntl236), MODE(0x01)}, /* EMAC[0]_MCOL */ + {OFFSET(pincntl237), MODE(0x01)}, /* EMAC[0]_MCRS */ + {OFFSET(pincntl238), MODE(0x01)}, /* EMAC[0]_MRXER */ + {OFFSET(pincntl239), MODE(0x01)}, /* EMAC[0]_MRCLK */ + {OFFSET(pincntl240), MODE(0x01)}, /* EMAC[0]_MRXD[0] */ + {OFFSET(pincntl241), MODE(0x01)}, /* EMAC[0]_MRXD[1] */ + {OFFSET(pincntl242), MODE(0x01)}, /* EMAC[0]_MRXD[2] */ + {OFFSET(pincntl243), MODE(0x01)}, /* EMAC[0]_MRXD[3] */ + {OFFSET(pincntl244), MODE(0x01)}, /* EMAC[0]_MRXD[4] */ + {OFFSET(pincntl245), MODE(0x01)}, /* EMAC[0]_MRXD[5] */ + {OFFSET(pincntl246), MODE(0x01)}, /* EMAC[0]_MRXD[6] */ + {OFFSET(pincntl247), MODE(0x01)}, /* EMAC[0]_MRXD[7] */ + {OFFSET(pincntl248), MODE(0x01)}, /* EMAC[0]_MRXDV */ + {OFFSET(pincntl249), MODE(0x01)}, /* EMAC[0]_GMTCLK */ + {OFFSET(pincntl250), MODE(0x01)}, /* EMAC[0]_MTXD[0] */ + {OFFSET(pincntl251), MODE(0x01)}, /* EMAC[0]_MTXD[1] */ + {OFFSET(pincntl252), MODE(0x01)}, /* EMAC[0]_MTXD[2] */ + {OFFSET(pincntl253), MODE(0x01)}, /* EMAC[0]_MTXD[3] */ + {OFFSET(pincntl254), MODE(0x01)}, /* EMAC[0]_MTXD[4] */ + {OFFSET(pincntl255), MODE(0x01)}, /* EMAC[0]_MTXD[5] */ + {OFFSET(pincntl256), MODE(0x01)}, /* EMAC[0]_MTXD[6] */ + {OFFSET(pincntl257), MODE(0x01)}, /* EMAC[0]_MTXD[7] */ + {OFFSET(pincntl258), MODE(0x01)}, /* EMAC[0]_MTXEN */ +}; + void enable_uart0_pin_mux(void) { configure_module_pin_mux(uart0_pin_mux); @@ -49,3 +79,8 @@ void enable_mmc1_pin_mux(void) { configure_module_pin_mux(mmc1_pin_mux); } + +void enable_enet_pin_mux(void) +{ + configure_module_pin_mux(enet_pin_mux); +} diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index 16547e33146..e646bd72350 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -218,4 +218,25 @@ /* Unsupported features */ #undef CONFIG_USE_IRQ +/* Ethernet */ +#define CONFIG_CMD_NET +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY_ET1011C +#define CONFIG_PHY_ET1011C_TX_CLK_FIX + #endif /* ! __CONFIG_TI814X_EVM_H */ -- cgit v1.3.1 From 0208aaf6c2e0f346e8410c0e5adb0ea784f00829 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:49 +0000 Subject: twl4030: make twl4030_i2c_write_u8 prototype consistent u-boot standard i2c register write prototype is i2c_reg_write(u8 addr, u8 reg, u8 val) twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val) Signed-off-by: Nishanth Menon --- board/cm_t35/cm_t35.c | 20 ++++++++++---------- board/nokia/rx51/rx51.c | 36 ++++++++++++++++++------------------ board/pandora/pandora.c | 3 ++- drivers/misc/twl4030_led.c | 4 ++-- drivers/power/twl4030.c | 12 ++++++------ drivers/usb/phy/twl4030.c | 46 +++++++++++++++++++++++----------------------- include/twl4030.h | 2 +- 7 files changed, 62 insertions(+), 61 deletions(-) (limited to 'include') diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c index 84c36bafb41..87d73546a2f 100644 --- a/board/cm_t35/cm_t35.c +++ b/board/cm_t35/cm_t35.c @@ -493,17 +493,17 @@ static void setup_net_chip_gmpc(void) static void reset_net_chip(void) { /* Set GPIO1 of TPS65930 as output */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x03); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x03, + 0x02); /* Send a pulse on the GPIO pin */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x0C); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C, + 0x02); udelay(1); - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x09); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x09, + 0x02); mdelay(40); - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0x02, - TWL4030_BASEADD_GPIO + 0x0C); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO + 0x0C, + 0x02); mdelay(1); } #else @@ -600,10 +600,10 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset); /* Set GPIO6 and GPIO7 of TPS65930 as output */ val |= 0xC0; - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, val, offset); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, val); offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_SETGPIODATAOUT1; /* Take both PHYs out of reset */ - twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, 0xC0, offset); + twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, 0xC0); udelay(1); return omap_ehci_hcd_init(&usbhs_bdata, hccr, hcor); diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c index 48eb65f8968..860d52da3f1 100644 --- a/board/nokia/rx51/rx51.c +++ b/board/nokia/rx51/rx51.c @@ -332,10 +332,10 @@ void *video_hw_init(void) static void twl4030_regulator_set_mode(u8 id, u8 mode) { u16 msg = MSG_SINGULAR(DEV_GRP_P1, id, mode); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg >> 8, - TWL4030_PM_MASTER_PB_WORD_MSB); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, msg & 0xff, - TWL4030_PM_MASTER_PB_WORD_LSB); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PB_WORD_MSB, msg >> 8); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PB_WORD_LSB, msg & 0xff); } static void omap3_emu_romcode_call(u32 service_id, u32 *parameters) @@ -410,8 +410,8 @@ int misc_init_r(void) TWL4030_PM_MASTER_PB_CFG); /* enable I2C access to powerbus (needed for twl4030 regulator) */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x02, - TWL4030_PM_MASTER_PB_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, + 0x02); /* set VAUX3, VSIM and VMMC1 state to active - enable eMMC memory */ twl4030_regulator_set_mode(RES_VAUX3, RES_STATE_ACTIVE); @@ -419,8 +419,8 @@ int misc_init_r(void) twl4030_regulator_set_mode(RES_VMMC1, RES_STATE_ACTIVE); /* restore I2C access state */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, state, - TWL4030_PM_MASTER_PB_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, + state); /* set env variable attkernaddr for relocated kernel */ sprintf(buf, "%#x", KERNEL_ADDRESS); @@ -481,8 +481,8 @@ void hw_watchdog_reset(void) /* timeout 0 means watchdog is disabled */ /* reset watchdog timeout to 31s (maximum) */ if (timeout != 0) - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 31, - TWL4030_PM_RECEIVER_WATCHDOG_CFG); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_WATCHDOG_CFG, 31); /* store last watchdog reset time */ twl_wd_time = get_timer(0); @@ -541,18 +541,18 @@ int rx51_kp_init(void) ctrl |= TWL4030_KEYPAD_CTRL_KBD_ON; ctrl |= TWL4030_KEYPAD_CTRL_SOFT_NRST; ctrl |= TWL4030_KEYPAD_CTRL_SOFTMODEN; - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, ctrl, - TWL4030_KEYPAD_KEYP_CTRL_REG); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_CTRL_REG, ctrl); /* enable key event status */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0xfe, - TWL4030_KEYPAD_KEYP_IMR1); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_IMR1, 0xfe); /* enable interrupt generation on rising and falling */ /* this is a workaround for qemu twl4030 emulation */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x57, - TWL4030_KEYPAD_KEYP_EDR); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_EDR, 0x57); /* enable ISR clear on read */ - ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, 0x05, - TWL4030_KEYPAD_KEYP_SIH_CTRL); + ret |= twl4030_i2c_write_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_SIH_CTRL, 0x05); return 0; } diff --git a/board/pandora/pandora.c b/board/pandora/pandora.c index 9ff5dd76641..5f0c58d8d2c 100644 --- a/board/pandora/pandora.c +++ b/board/pandora/pandora.c @@ -114,8 +114,9 @@ int misc_init_r(void) /* Enable battery backup capacitor (3.2V, 0.5mA charge current) */ twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_BB_CFG, TWL4030_BB_CFG_BBCHEN | TWL4030_BB_CFG_BBSEL_3200MV | - TWL4030_BB_CFG_BBISEL_500UA, TWL4030_PM_RECEIVER_BB_CFG); + TWL4030_BB_CFG_BBISEL_500UA); dieid_num_r(); diff --git a/drivers/misc/twl4030_led.c b/drivers/misc/twl4030_led.c index 33cea116d29..e150d8f0372 100644 --- a/drivers/misc/twl4030_led.c +++ b/drivers/misc/twl4030_led.c @@ -42,7 +42,7 @@ void twl4030_led_init(unsigned char ledon_mask) if (ledon_mask & TWL4030_LED_LEDEN_LEDBON) ledon_mask |= TWL4030_LED_LEDEN_LEDBPWM; - twl4030_i2c_write_u8(TWL4030_CHIP_LED, ledon_mask, - TWL4030_LED_LEDEN); + twl4030_i2c_write_u8(TWL4030_CHIP_LED, TWL4030_LED_LEDEN, + ledon_mask); } diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c index e7d5f132b2b..2bf94b134c6 100644 --- a/drivers/power/twl4030.c +++ b/drivers/power/twl4030.c @@ -51,8 +51,8 @@ void twl4030_power_reset_init(void) printf("Could not initialize hardware reset\n"); } else { val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON; - if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, val, - TWL4030_PM_MASTER_P1_SW_EVENTS)) { + if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_P1_SW_EVENTS, val)) { printf("Error:TWL4030: failed to write the power register\n"); printf("Could not initialize hardware reset\n"); } @@ -68,8 +68,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val, int ret; /* Select the Voltage */ - ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_val, - vsel_reg); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, vsel_reg, + vsel_val); if (ret != 0) { printf("Could not write vsel to reg %02x (%d)\n", vsel_reg, ret); @@ -77,8 +77,8 @@ void twl4030_pmrecv_vsel_cfg(u8 vsel_reg, u8 vsel_val, } /* Select the Device Group (enable the supply if dev_grp_sel != 0) */ - ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp_sel, - dev_grp); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, dev_grp, + dev_grp_sel); if (ret != 0) printf("Could not write grp_sel to reg %02x (%d)\n", dev_grp, ret); diff --git a/drivers/usb/phy/twl4030.c b/drivers/usb/phy/twl4030.c index 54d2e615c80..f41cc07fe70 100644 --- a/drivers/usb/phy/twl4030.c +++ b/drivers/usb/phy/twl4030.c @@ -54,7 +54,7 @@ static int twl4030_usb_write(u8 address, u8 data) { int ret; - ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, data, address); + ret = twl4030_i2c_write_u8(TWL4030_CHIP_USB, address, data); if (ret != 0) printf("TWL4030:USB:Write[0x%x] Error %d\n", address, ret); @@ -78,40 +78,40 @@ static int twl4030_usb_read(u8 address) static void twl4030_usb_ldo_init(void) { /* Enable writing to power configuration registers */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0xC0, - TWL4030_PM_MASTER_PROTECT_KEY); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x0C, - TWL4030_PM_MASTER_PROTECT_KEY); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0xC0); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0x0C); /* put VUSB3V1 LDO in active state */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB_DEDICATED2); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB_DEDICATED2, 0x00); /* input to VUSB3V1 LDO is from VBAT, not VBUS */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x14, - TWL4030_PM_RECEIVER_VUSB_DEDICATED1); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB_DEDICATED1, 0x14); /* turn on 3.1V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB3V1_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB3V1_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB3V1_TYPE, 0x00); /* turn on 1.5V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB1V5_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V5_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V5_TYPE, 0x00); /* turn on 1.8V regulator */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x20, - TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP); - twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, 0x00, - TWL4030_PM_RECEIVER_VUSB1V8_TYPE); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V8_DEV_GRP, 0x20); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_VUSB1V8_TYPE, 0x00); /* disable access to power configuration registers */ - twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, 0x00, - TWL4030_PM_MASTER_PROTECT_KEY); + twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_PROTECT_KEY, 0x00); } static void twl4030_phy_power(void) diff --git a/include/twl4030.h b/include/twl4030.h index 5aa184183e7..aca695d5bb5 100644 --- a/include/twl4030.h +++ b/include/twl4030.h @@ -638,7 +638,7 @@ * examples are TWL4030_PM_RECEIVER_VMMC1_DEV_GRP and * TWL4030_LED_LEDEN. */ -static inline int twl4030_i2c_write_u8(u8 chip_no, u8 val, u8 reg) +static inline int twl4030_i2c_write_u8(u8 chip_no, u8 reg, u8 val) { return i2c_write(chip_no, reg, 1, &val, 1); } -- cgit v1.3.1 From b29c2f0c142fdb8ef50deae1cc7c4338952fba6c Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:50 +0000 Subject: twl4030: make twl4030_i2c_read_u8 prototype consistent u-boot standard i2c read prototype is i2c_read(addr, reg, 1, &buf, 1) twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val) Signed-off-by: Nishanth Menon --- board/cm_t35/cm_t35.c | 4 ++-- board/nokia/rx51/rx51.c | 16 ++++++++-------- drivers/power/twl4030.c | 4 ++-- drivers/usb/phy/twl4030.c | 2 +- include/twl4030.h | 2 +- 5 files changed, 14 insertions(+), 14 deletions(-) (limited to 'include') diff --git a/board/cm_t35/cm_t35.c b/board/cm_t35/cm_t35.c index 87d73546a2f..85286809d3d 100644 --- a/board/cm_t35/cm_t35.c +++ b/board/cm_t35/cm_t35.c @@ -448,7 +448,7 @@ int board_mmc_getcd(struct mmc *mmc) { u8 val; - if (twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, TWL4030_BASEADD_GPIO)) + if (twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, TWL4030_BASEADD_GPIO, &val)) return -1; return !(val & 1); @@ -597,7 +597,7 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) udelay(1000); offset = TWL4030_BASEADD_GPIO + TWL4030_GPIO_GPIODATADIR1; - twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, &val, offset); + twl4030_i2c_read_u8(TWL4030_CHIP_GPIO, offset, &val); /* Set GPIO6 and GPIO7 of TPS65930 as output */ val |= 0xC0; twl4030_i2c_write_u8(TWL4030_CHIP_GPIO, offset, val); diff --git a/board/nokia/rx51/rx51.c b/board/nokia/rx51/rx51.c index 860d52da3f1..42bf8b669d7 100644 --- a/board/nokia/rx51/rx51.c +++ b/board/nokia/rx51/rx51.c @@ -406,8 +406,8 @@ int misc_init_r(void) TWL4030_PM_RECEIVER_DEV_GRP_P1); /* store I2C access state */ - twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, &state, - TWL4030_PM_MASTER_PB_CFG); + twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, + &state); /* enable I2C access to powerbus (needed for twl4030 regulator) */ twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, TWL4030_PM_MASTER_PB_CFG, @@ -475,8 +475,8 @@ void hw_watchdog_reset(void) return; /* read actual watchdog timeout */ - twl4030_i2c_read_u8(TWL4030_CHIP_PM_RECEIVER, &timeout, - TWL4030_PM_RECEIVER_WATCHDOG_CFG); + twl4030_i2c_read_u8(TWL4030_CHIP_PM_RECEIVER, + TWL4030_PM_RECEIVER_WATCHDOG_CFG, &timeout); /* timeout 0 means watchdog is disabled */ /* reset watchdog timeout to 31s (maximum) */ @@ -531,8 +531,8 @@ int rx51_kp_init(void) { int ret = 0; u8 ctrl; - ret = twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, &ctrl, - TWL4030_KEYPAD_KEYP_CTRL_REG); + ret = twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_CTRL_REG, &ctrl); if (ret) return ret; @@ -615,8 +615,8 @@ int rx51_kp_tstc(void) for (i = 0; i < 2; i++) { /* check interrupt register for events */ - twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, &intr, - TWL4030_KEYPAD_KEYP_ISR1+(2*i)); + twl4030_i2c_read_u8(TWL4030_CHIP_KEYPAD, + TWL4030_KEYPAD_KEYP_ISR1 + (2 * i), &intr); /* no event */ if (!(intr&1)) diff --git a/drivers/power/twl4030.c b/drivers/power/twl4030.c index 2bf94b134c6..6610f787d0c 100644 --- a/drivers/power/twl4030.c +++ b/drivers/power/twl4030.c @@ -45,8 +45,8 @@ void twl4030_power_reset_init(void) { u8 val = 0; - if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, &val, - TWL4030_PM_MASTER_P1_SW_EVENTS)) { + if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, + TWL4030_PM_MASTER_P1_SW_EVENTS, &val)) { printf("Error:TWL4030: failed to read the power register\n"); printf("Could not initialize hardware reset\n"); } else { diff --git a/drivers/usb/phy/twl4030.c b/drivers/usb/phy/twl4030.c index f41cc07fe70..74f1dccbd49 100644 --- a/drivers/usb/phy/twl4030.c +++ b/drivers/usb/phy/twl4030.c @@ -66,7 +66,7 @@ static int twl4030_usb_read(u8 address) u8 data; int ret; - ret = twl4030_i2c_read_u8(TWL4030_CHIP_USB, &data, address); + ret = twl4030_i2c_read_u8(TWL4030_CHIP_USB, address, &data); if (ret == 0) ret = data; else diff --git a/include/twl4030.h b/include/twl4030.h index aca695d5bb5..569ad2773fb 100644 --- a/include/twl4030.h +++ b/include/twl4030.h @@ -643,7 +643,7 @@ static inline int twl4030_i2c_write_u8(u8 chip_no, u8 reg, u8 val) return i2c_write(chip_no, reg, 1, &val, 1); } -static inline int twl4030_i2c_read_u8(u8 chip_no, u8 *val, u8 reg) +static inline int twl4030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val) { return i2c_read(chip_no, reg, 1, val, 1); } -- cgit v1.3.1 From ebce10e5b2542e71e1201c85dbe3b6432569a497 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:52 +0000 Subject: twl6030: move twl6030 register access functions to common header file twl6030_i2c_[read|write]_u8 can be used else where to access multi-function device such as twl6030, so move the register access functions to the common twl6030.h header file. Signed-off-by: Nishanth Menon --- drivers/power/twl6030.c | 11 ----------- include/twl6030.h | 11 +++++++++++ 2 files changed, 11 insertions(+), 11 deletions(-) (limited to 'include') diff --git a/drivers/power/twl6030.c b/drivers/power/twl6030.c index 58ad4ad3664..d421e6005ba 100644 --- a/drivers/power/twl6030.c +++ b/drivers/power/twl6030.c @@ -25,17 +25,6 @@ #include -/* Functions to read and write from TWL6030 */ -static inline int twl6030_i2c_write_u8(u8 chip_no, u8 reg, u8 val) -{ - return i2c_write(chip_no, reg, 1, &val, 1); -} - -static inline int twl6030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val) -{ - return i2c_read(chip_no, reg, 1, val, 1); -} - static int twl6030_gpadc_read_channel(u8 channel_no) { u8 lsb = 0; diff --git a/include/twl6030.h b/include/twl6030.h index a9fcadbfef7..f7ba3c7b1ff 100644 --- a/include/twl6030.h +++ b/include/twl6030.h @@ -126,6 +126,17 @@ #define GPCH0_LSB 0x57 #define GPCH0_MSB 0x58 +/* Functions to read and write from TWL6030 */ +static inline int twl6030_i2c_write_u8(u8 chip_no, u8 reg, u8 val) +{ + return i2c_write(chip_no, reg, 1, &val, 1); +} + +static inline int twl6030_i2c_read_u8(u8 chip_no, u8 reg, u8 *val) +{ + return i2c_read(chip_no, reg, 1, val, 1); +} + void twl6030_init_battery_charging(void); void twl6030_usb_device_settings(void); void twl6030_start_usb_charging(void); -- cgit v1.3.1 From 502dac5568df4c67d7bb53b4aca242f2435eed73 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:53 +0000 Subject: twl6030: add header guard Add an header guard to common header file to prevent multiple includes messing things up. Signed-off-by: Nishanth Menon --- include/twl6030.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include') diff --git a/include/twl6030.h b/include/twl6030.h index f7ba3c7b1ff..029b21f7108 100644 --- a/include/twl6030.h +++ b/include/twl6030.h @@ -21,6 +21,9 @@ * MA 02111-1307 USA */ +#ifndef TWL6030_H +#define TWL6030_H + #include #include @@ -144,3 +147,5 @@ void twl6030_stop_usb_charging(void); int twl6030_get_battery_voltage(void); int twl6030_get_battery_current(void); void twl6030_power_mmc_init(void); + +#endif /* TWL6030_H */ -- cgit v1.3.1 From cb199102b06c5d895d2495c62554c5be998b234b Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:54 +0000 Subject: twl6035: rename to palmas TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs Rename twl6035 to palmas to allow reuse across multiple current and future platforms As part of this change, change the CONFIG_TWL6035_POWER to CONFIG_PALMAS_POWER and update usage of header file accordingly. Signed-off-by: Nishanth Menon --- board/ti/dra7xx/evm.c | 2 +- board/ti/omap5_uevm/evm.c | 4 +-- drivers/mmc/omap_hsmmc.c | 6 ++-- drivers/power/Makefile | 2 +- drivers/power/palmas.c | 74 ++++++++++++++++++++++++++++++++++++++++++++ drivers/power/twl6035.c | 74 -------------------------------------------- include/configs/omap5_uevm.h | 2 +- include/palmas.h | 42 +++++++++++++++++++++++++ include/twl6035.h | 42 ------------------------- 9 files changed, 124 insertions(+), 124 deletions(-) create mode 100644 drivers/power/palmas.c delete mode 100644 drivers/power/twl6035.c create mode 100644 include/palmas.h delete mode 100644 include/twl6035.h (limited to 'include') diff --git a/board/ti/dra7xx/evm.c b/board/ti/dra7xx/evm.c index 7bbb5492feb..bf7e0919665 100644 --- a/board/ti/dra7xx/evm.c +++ b/board/ti/dra7xx/evm.c @@ -27,7 +27,7 @@ * MA 02111-1307 USA */ #include -#include +#include #include #include diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c index 55337c09d5e..701842bdd1d 100644 --- a/board/ti/omap5_uevm/evm.c +++ b/board/ti/omap5_uevm/evm.c @@ -23,7 +23,7 @@ * MA 02111-1307 USA */ #include -#include +#include #include #include @@ -63,7 +63,7 @@ int board_eth_init(bd_t *bis) */ int misc_init_r(void) { -#ifdef CONFIG_TWL6035_POWER +#ifdef CONFIG_PALMAS_POWER twl6035_init_settings(); #endif return 0; diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index 166744c3204..b39db9e32fe 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -29,7 +29,7 @@ #include #include #include -#include +#include #include #include #include @@ -107,7 +107,7 @@ static void omap4_vmmc_pbias_config(struct mmc *mmc) } #endif -#if defined(CONFIG_OMAP54XX) && defined(CONFIG_TWL6035_POWER) +#if defined(CONFIG_OMAP54XX) && defined(CONFIG_PALMAS_POWER) static void omap5_pbias_config(struct mmc *mmc) { u32 value = 0; @@ -178,7 +178,7 @@ unsigned char mmc_board_init(struct mmc *mmc) if (mmc->block_dev.dev == 0) omap4_vmmc_pbias_config(mmc); #endif -#if defined(CONFIG_OMAP54XX) && defined(CONFIG_TWL6035_POWER) +#if defined(CONFIG_OMAP54XX) && defined(CONFIG_PALMAS_POWER) if (mmc->block_dev.dev == 0) omap5_pbias_config(mmc); #endif diff --git a/drivers/power/Makefile b/drivers/power/Makefile index 1dac16a9f7d..a9c42370f99 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -30,7 +30,7 @@ COBJS-$(CONFIG_FTPMU010_POWER) += ftpmu010.o COBJS-$(CONFIG_TPS6586X_POWER) += tps6586x.o COBJS-$(CONFIG_TWL4030_POWER) += twl4030.o COBJS-$(CONFIG_TWL6030_POWER) += twl6030.o -COBJS-$(CONFIG_TWL6035_POWER) += twl6035.o +COBJS-$(CONFIG_PALMAS_POWER) += palmas.o COBJS-$(CONFIG_POWER) += power_core.o COBJS-$(CONFIG_DIALOG_POWER) += power_dialog.o diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c new file mode 100644 index 00000000000..8ed77421d6b --- /dev/null +++ b/drivers/power/palmas.c @@ -0,0 +1,74 @@ +/* + * (C) Copyright 2012-2013 + * Texas Instruments, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include +#include + +/* Functions to read and write from TWL6030 */ +int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg) +{ + return i2c_write(chip_no, reg, 1, &val, 1); +} + +int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg) +{ + return i2c_read(chip_no, reg, 1, val, 1); +} + +/* To align with i2c mw/mr address, reg, val command syntax */ +static inline int palmas_write_u8(u8 chip_no, u8 reg, u8 val) +{ + return i2c_write(chip_no, reg, 1, &val, 1); +} + +static inline int palmas_read_u8(u8 chip_no, u8 reg, u8 *val) +{ + return i2c_read(chip_no, reg, 1, val, 1); +} + +void twl6035_init_settings(void) +{ + return; +} + +int twl6035_mmc1_poweron_ldo(void) +{ + u8 val = 0; + + /* set LDO9 TWL6035 to 3V */ + val = 0x2b; /* (3 -.9)*28 +1 */ + + if (palmas_write_u8(0x48, LDO9_VOLTAGE, val)) { + printf("twl6035: could not set LDO9 voltage.\n"); + return 1; + } + + /* TURN ON LDO9 */ + val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE; + + if (palmas_write_u8(0x48, LDO9_CTRL, val)) { + printf("twl6035: could not turn on LDO9.\n"); + return 1; + } + + return 0; +} diff --git a/drivers/power/twl6035.c b/drivers/power/twl6035.c deleted file mode 100644 index d3de698cde7..00000000000 --- a/drivers/power/twl6035.c +++ /dev/null @@ -1,74 +0,0 @@ -/* - * (C) Copyright 2012 - * Texas Instruments, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ -#include -#include - -/* Functions to read and write from TWL6030 */ -int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg) -{ - return i2c_write(chip_no, reg, 1, &val, 1); -} - -int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg) -{ - return i2c_read(chip_no, reg, 1, val, 1); -} - -/* To align with i2c mw/mr address, reg, val command syntax */ -static inline int palmas_write_u8(u8 chip_no, u8 reg, u8 val) -{ - return i2c_write(chip_no, reg, 1, &val, 1); -} - -static inline int palmas_read_u8(u8 chip_no, u8 reg, u8 *val) -{ - return i2c_read(chip_no, reg, 1, val, 1); -} - -void twl6035_init_settings(void) -{ - return; -} - -int twl6035_mmc1_poweron_ldo(void) -{ - u8 val = 0; - - /* set LDO9 TWL6035 to 3V */ - val = 0x2b; /* (3 -.9)*28 +1 */ - - if (palmas_write_u8(0x48, LDO9_VOLTAGE, val)) { - printf("twl6035: could not set LDO9 voltage.\n"); - return 1; - } - - /* TURN ON LDO9 */ - val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE; - - if (palmas_write_u8(0x48, LDO9_CTRL, val)) { - printf("twl6035: could not turn on LDO9.\n"); - return 1; - } - - return 0; -} diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 240fdfcb478..c5bf51d9c95 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -37,7 +37,7 @@ /* TWL6035 */ #ifndef CONFIG_SPL_BUILD -#define CONFIG_TWL6035_POWER +#define CONFIG_PALMAS_POWER #endif /* MMC ENV related defines */ diff --git a/include/palmas.h b/include/palmas.h new file mode 100644 index 00000000000..cf836d7d6c5 --- /dev/null +++ b/include/palmas.h @@ -0,0 +1,42 @@ +/* + * (C) Copyright 2012-2013 + * Texas Instruments, + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +/* I2C chip addresses */ +#define PALMAS_CHIP_ADDR 0x48 + +/* 0x1XY translates to page 1, register address 0xXY */ +#define LDO9_CTRL 0x60 +#define LDO9_VOLTAGE 0x61 + +/* Bit field definitions for LDOx_CTRL */ +#define LDO_ON (1 << 4) +#define LDO_MODE_SLEEP (1 << 2) +#define LDO_MODE_ACTIVE (1 << 0) + +int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg); +int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg); +void twl6035_init_settings(void); +int twl6035_mmc1_poweron_ldo(void); diff --git a/include/twl6035.h b/include/twl6035.h deleted file mode 100644 index ce74348d443..00000000000 --- a/include/twl6035.h +++ /dev/null @@ -1,42 +0,0 @@ -/* - * (C) Copyright 2012 - * Texas Instruments, - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include - -/* I2C chip addresses */ -#define TWL6035_CHIP_ADDR 0x48 - -/* 0x1XY translates to page 1, register address 0xXY */ -#define LDO9_CTRL 0x60 -#define LDO9_VOLTAGE 0x61 - -/* Bit field definitions for LDOx_CTRL */ -#define LDO_ON (1 << 4) -#define LDO_MODE_SLEEP (1 << 2) -#define LDO_MODE_ACTIVE (1 << 0) - -int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg); -int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg); -void twl6035_init_settings(void); -int twl6035_mmc1_poweron_ldo(void); -- cgit v1.3.1 From 12733881e94018f9a9b0cdb72c7ab55638142220 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:55 +0000 Subject: palmas: rename init_settings to an generic palmas init Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_init_settings with an more generic palmas_init_settings Signed-off-by: Nishanth Menon --- board/ti/omap5_uevm/evm.c | 2 +- drivers/power/palmas.c | 2 +- include/palmas.h | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/board/ti/omap5_uevm/evm.c b/board/ti/omap5_uevm/evm.c index 701842bdd1d..46db1bfe664 100644 --- a/board/ti/omap5_uevm/evm.c +++ b/board/ti/omap5_uevm/evm.c @@ -64,7 +64,7 @@ int board_eth_init(bd_t *bis) int misc_init_r(void) { #ifdef CONFIG_PALMAS_POWER - twl6035_init_settings(); + palmas_init_settings(); #endif return 0; } diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c index 8ed77421d6b..bf36a19aa1e 100644 --- a/drivers/power/palmas.c +++ b/drivers/power/palmas.c @@ -45,7 +45,7 @@ static inline int palmas_read_u8(u8 chip_no, u8 reg, u8 *val) return i2c_read(chip_no, reg, 1, val, 1); } -void twl6035_init_settings(void) +void palmas_init_settings(void) { return; } diff --git a/include/palmas.h b/include/palmas.h index cf836d7d6c5..6618aad4916 100644 --- a/include/palmas.h +++ b/include/palmas.h @@ -38,5 +38,5 @@ int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg); int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg); -void twl6035_init_settings(void); +void palmas_init_settings(void); int twl6035_mmc1_poweron_ldo(void); -- cgit v1.3.1 From 384bcae013c78e020e9a04df4c7cc3b451a68811 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:56 +0000 Subject: palmas: rename twl6035_mmc1_poweron_ldo with an palmas generic function Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo function. Signed-off-by: Nishanth Menon --- drivers/mmc/omap_hsmmc.c | 2 +- drivers/power/palmas.c | 2 +- include/palmas.h | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index b39db9e32fe..afdfa886e8a 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -117,7 +117,7 @@ static void omap5_pbias_config(struct mmc *mmc) value |= SDCARD_BIAS_HIZ_MODE; writel(value, (*ctrl)->control_pbias); - twl6035_mmc1_poweron_ldo(); + palmas_mmc1_poweron_ldo(); value = readl((*ctrl)->control_pbias); value &= ~SDCARD_BIAS_HIZ_MODE; diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c index bf36a19aa1e..489a7a9fe29 100644 --- a/drivers/power/palmas.c +++ b/drivers/power/palmas.c @@ -50,7 +50,7 @@ void palmas_init_settings(void) return; } -int twl6035_mmc1_poweron_ldo(void) +int palmas_mmc1_poweron_ldo(void) { u8 val = 0; diff --git a/include/palmas.h b/include/palmas.h index 6618aad4916..305092e1cee 100644 --- a/include/palmas.h +++ b/include/palmas.h @@ -39,4 +39,4 @@ int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg); int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg); void palmas_init_settings(void); -int twl6035_mmc1_poweron_ldo(void); +int palmas_mmc1_poweron_ldo(void); -- cgit v1.3.1 From ff2d57ea5e9b56e22c84647b9532292e5ea862f9 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:57 +0000 Subject: palmas: use palmas_i2c_[read|write]_u8 commit 21144298 (power: twl6035: add palmas PMIC support) introduced twl6035_i2c_[read|write]_u8 Then, commit dd23e59d (omap5: pbias ldo9 turn on) introduced palmas_[read|write]_u8 for precisely the same access function. TWL6035 belongs to the palmas family, so instead of having an twl6035 API, we could use an generic palmas API instead. To stay consistent with the function naming of twl4030,6030 accessors, we use palmas_i2c_[read|write]_u8 Cc: Balaji T K Cc: Sricharan R Reported-by: Ruchika Kharwar Signed-off-by: Nishanth Menon --- drivers/power/palmas.c | 26 ++------------------------ include/palmas.h | 16 ++++++++++++++-- 2 files changed, 16 insertions(+), 26 deletions(-) (limited to 'include') diff --git a/drivers/power/palmas.c b/drivers/power/palmas.c index 489a7a9fe29..09c832d8b6e 100644 --- a/drivers/power/palmas.c +++ b/drivers/power/palmas.c @@ -23,28 +23,6 @@ #include #include -/* Functions to read and write from TWL6030 */ -int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg) -{ - return i2c_write(chip_no, reg, 1, &val, 1); -} - -int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg) -{ - return i2c_read(chip_no, reg, 1, val, 1); -} - -/* To align with i2c mw/mr address, reg, val command syntax */ -static inline int palmas_write_u8(u8 chip_no, u8 reg, u8 val) -{ - return i2c_write(chip_no, reg, 1, &val, 1); -} - -static inline int palmas_read_u8(u8 chip_no, u8 reg, u8 *val) -{ - return i2c_read(chip_no, reg, 1, val, 1); -} - void palmas_init_settings(void) { return; @@ -57,7 +35,7 @@ int palmas_mmc1_poweron_ldo(void) /* set LDO9 TWL6035 to 3V */ val = 0x2b; /* (3 -.9)*28 +1 */ - if (palmas_write_u8(0x48, LDO9_VOLTAGE, val)) { + if (palmas_i2c_write_u8(0x48, LDO9_VOLTAGE, val)) { printf("twl6035: could not set LDO9 voltage.\n"); return 1; } @@ -65,7 +43,7 @@ int palmas_mmc1_poweron_ldo(void) /* TURN ON LDO9 */ val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE; - if (palmas_write_u8(0x48, LDO9_CTRL, val)) { + if (palmas_i2c_write_u8(0x48, LDO9_CTRL, val)) { printf("twl6035: could not turn on LDO9.\n"); return 1; } diff --git a/include/palmas.h b/include/palmas.h index 305092e1cee..e629fbf9988 100644 --- a/include/palmas.h +++ b/include/palmas.h @@ -36,7 +36,19 @@ #define LDO_MODE_SLEEP (1 << 2) #define LDO_MODE_ACTIVE (1 << 0) -int twl6035_i2c_write_u8(u8 chip_no, u8 val, u8 reg); -int twl6035_i2c_read_u8(u8 chip_no, u8 *val, u8 reg); +/* + * Functions to read and write from TPS659038/TWL6035/TWL6037 + * or other Palmas family of TI PMICs + */ +static inline int palmas_i2c_write_u8(u8 chip_no, u8 reg, u8 val) +{ + return i2c_write(chip_no, reg, 1, &val, 1); +} + +static inline int palmas_i2c_read_u8(u8 chip_no, u8 reg, u8 *val) +{ + return i2c_read(chip_no, reg, 1, val, 1); +} + void palmas_init_settings(void); int palmas_mmc1_poweron_ldo(void); -- cgit v1.3.1 From da2cc4545b7dfcff32eb2bb7feab43e1be9792f6 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 26 Mar 2013 05:20:58 +0000 Subject: palmas: add header guard Add an header guard to common header file to prevent multiple includes messing things up. Signed-off-by: Nishanth Menon --- include/palmas.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'include') diff --git a/include/palmas.h b/include/palmas.h index e629fbf9988..3b185896d63 100644 --- a/include/palmas.h +++ b/include/palmas.h @@ -20,6 +20,8 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ +#ifndef PALMAS_H +#define PALMAS_H #include #include @@ -52,3 +54,5 @@ static inline int palmas_i2c_read_u8(u8 chip_no, u8 reg, u8 *val) void palmas_init_settings(void); int palmas_mmc1_poweron_ldo(void); + +#endif /* PALMAS_H */ -- cgit v1.3.1 From 5f5c1d13d3b3bb97fae1ed8c3c9e35b4af0f19e5 Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Thu, 4 Apr 2013 22:27:58 +0000 Subject: ARM: Add support for IGEP COM AQUILA/CYGNUS The IGEP COM AQUILA and CYGNUS are industrial processors modules with following highlights: o AM3352/AM3354 Texas Instruments processor o Cortex-A8 ARM CPU o 3.3 volts Inputs / Outputs use industrial o 256 MB DDR3 SDRAM / 128 Megabytes FLASH o MicroSD card reader on-board o Ethernet controller on-board o JTAG debug connector available o Designed for industrial range purposes Signed-off-by: Enric Balletbo i Serra --- MAINTAINERS | 1 + board/isee/igep0033/Makefile | 46 +++++++ board/isee/igep0033/board.c | 232 +++++++++++++++++++++++++++++++++++ board/isee/igep0033/board.h | 27 ++++ board/isee/igep0033/mux.c | 89 ++++++++++++++ boards.cfg | 1 + include/configs/igep0033.h | 284 +++++++++++++++++++++++++++++++++++++++++++ 7 files changed, 680 insertions(+) create mode 100644 board/isee/igep0033/Makefile create mode 100644 board/isee/igep0033/board.c create mode 100644 board/isee/igep0033/board.h create mode 100644 board/isee/igep0033/mux.c create mode 100644 include/configs/igep0033.h (limited to 'include') diff --git a/MAINTAINERS b/MAINTAINERS index 643a5acc412..a46803cd5fb 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -607,6 +607,7 @@ Enric Balletbo i Serra igep0020 ARM ARMV7 (OMAP3xx SoC) igep0030 ARM ARMV7 (OMAP3xx SoC) igep0032 ARM ARMV7 (OMAP3xx SoC) + igep0033 ARM ARMV7 (AM33xx Soc) Eric Benard diff --git a/board/isee/igep0033/Makefile b/board/isee/igep0033/Makefile new file mode 100644 index 00000000000..54a4b75252d --- /dev/null +++ b/board/isee/igep0033/Makefile @@ -0,0 +1,46 @@ +# +# Makefile +# +# Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed "as is" WITHOUT ANY WARRANTY of any +# kind, whether express or implied; without even the implied warranty +# of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +ifdef CONFIG_SPL_BUILD +COBJS := mux.o +endif + +COBJS += board.o +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c new file mode 100644 index 00000000000..d315516fea4 --- /dev/null +++ b/board/isee/igep0033/board.c @@ -0,0 +1,232 @@ +/* + * Board functions for IGEP COM AQUILA/CYGNUS based boards + * + * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "board.h" + +DECLARE_GLOBAL_DATA_PTR; + +static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; +#ifdef CONFIG_SPL_BUILD +static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; +#endif + +/* MII mode defines */ +#define RMII_MODE_ENABLE 0x4D + +static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; + +/* UART Defines */ +#ifdef CONFIG_SPL_BUILD +#define UART_RESET (0x1 << 1) +#define UART_CLK_RUNNING_MASK 0x1 +#define UART_SMART_IDLE_EN (0x1 << 0x3) + +static void rtc32k_enable(void) +{ + struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE; + + /* + * Unlock the RTC's registers. For more details please see the + * RTC_SS section of the TRM. In order to unlock we need to + * write these specific values (keys) in this order. + */ + writel(0x83e70b13, &rtc->kick0r); + writel(0x95a4f1e0, &rtc->kick1r); + + /* Enable the RTC 32K OSC by setting bits 3 and 6. */ + writel((1 << 3) | (1 << 6), &rtc->osc); +} + +static const struct ddr_data ddr3_data = { + .datardsratio0 = K4B2G1646EBIH9_RD_DQS, + .datawdsratio0 = K4B2G1646EBIH9_WR_DQS, + .datafwsratio0 = K4B2G1646EBIH9_PHY_FIFO_WE, + .datawrsratio0 = K4B2G1646EBIH9_PHY_WR_DATA, + .datadldiff0 = PHY_DLL_LOCK_DIFF, +}; + +static const struct cmd_control ddr3_cmd_ctrl_data = { + .cmd0csratio = K4B2G1646EBIH9_RATIO, + .cmd0dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF, + .cmd0iclkout = K4B2G1646EBIH9_INVERT_CLKOUT, + + .cmd1csratio = K4B2G1646EBIH9_RATIO, + .cmd1dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF, + .cmd1iclkout = K4B2G1646EBIH9_INVERT_CLKOUT, + + .cmd2csratio = K4B2G1646EBIH9_RATIO, + .cmd2dldiff = K4B2G1646EBIH9_DLL_LOCK_DIFF, + .cmd2iclkout = K4B2G1646EBIH9_INVERT_CLKOUT, +}; + +static struct emif_regs ddr3_emif_reg_data = { + .sdram_config = K4B2G1646EBIH9_EMIF_SDCFG, + .ref_ctrl = K4B2G1646EBIH9_EMIF_SDREF, + .sdram_tim1 = K4B2G1646EBIH9_EMIF_TIM1, + .sdram_tim2 = K4B2G1646EBIH9_EMIF_TIM2, + .sdram_tim3 = K4B2G1646EBIH9_EMIF_TIM3, + .zq_config = K4B2G1646EBIH9_ZQ_CFG, + .emif_ddr_phy_ctlr_1 = K4B2G1646EBIH9_EMIF_READ_LATENCY, +}; +#endif + +/* + * Early system init of muxing and clocks. + */ +void s_init(void) +{ + /* WDT1 is already running when the bootloader gets control + * Disable it to avoid "random" resets + */ + writel(0xAAAA, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; + writel(0x5555, &wdtimer->wdtwspr); + while (readl(&wdtimer->wdtwwps) != 0x0) + ; + +#ifdef CONFIG_SPL_BUILD + /* Setup the PLLs and the clocks for the peripherals */ + pll_init(); + + /* Enable RTC32K clock */ + rtc32k_enable(); + + /* UART softreset */ + u32 regval; + + enable_uart0_pin_mux(); + + regval = readl(&uart_base->uartsyscfg); + regval |= UART_RESET; + writel(regval, &uart_base->uartsyscfg); + while ((readl(&uart_base->uartsyssts) & + UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK) + ; + + /* Disable smart idle */ + regval = readl(&uart_base->uartsyscfg); + regval |= UART_SMART_IDLE_EN; + writel(regval, &uart_base->uartsyscfg); + + gd = &gdata; + + preloader_console_init(); + + /* Configure board pin mux */ + enable_board_pin_mux(); + + config_ddr(303, K4B2G1646EBIH9_IOCTRL_VALUE, &ddr3_data, + &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); +#endif +} + +/* + * Basic board specific setup. Pinmux has been handled already. + */ +int board_init(void) +{ + gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100; + + gpmc_init(); + + return 0; +} + +#if defined(CONFIG_DRIVER_TI_CPSW) +static void cpsw_control(int enabled) +{ + /* VTP can be added here */ + + return; +} + +static struct cpsw_slave_data cpsw_slaves[] = { + { + .slave_reg_ofs = 0x208, + .sliver_reg_ofs = 0xd80, + .phy_id = 0, + .phy_if = PHY_INTERFACE_MODE_RMII, + }, +}; + +static struct cpsw_platform_data cpsw_data = { + .mdio_base = CPSW_MDIO_BASE, + .cpsw_base = CPSW_BASE, + .mdio_div = 0xff, + .channels = 8, + .cpdma_reg_ofs = 0x800, + .slaves = 1, + .slave_data = cpsw_slaves, + .ale_reg_ofs = 0xd00, + .ale_entries = 1024, + .host_port_reg_ofs = 0x108, + .hw_stats_reg_ofs = 0x900, + .mac_control = (1 << 5), + .control = cpsw_control, + .host_port_num = 0, + .version = CPSW_CTRL_VERSION_2, +}; + +int board_eth_init(bd_t *bis) +{ + int rv, ret = 0; + uint8_t mac_addr[6]; + uint32_t mac_hi, mac_lo; + + if (!eth_getenv_enetaddr("ethaddr", mac_addr)) { + /* try reading mac address from efuse */ + mac_lo = readl(&cdev->macid0l); + mac_hi = readl(&cdev->macid0h); + mac_addr[0] = mac_hi & 0xFF; + mac_addr[1] = (mac_hi & 0xFF00) >> 8; + mac_addr[2] = (mac_hi & 0xFF0000) >> 16; + mac_addr[3] = (mac_hi & 0xFF000000) >> 24; + mac_addr[4] = mac_lo & 0xFF; + mac_addr[5] = (mac_lo & 0xFF00) >> 8; + if (is_valid_ether_addr(mac_addr)) + eth_setenv_enetaddr("ethaddr", mac_addr); + } + + writel(RMII_MODE_ENABLE, &cdev->miisel); + + rv = cpsw_register(&cpsw_data); + if (rv < 0) + printf("Error %d registering CPSW switch\n", rv); + else + ret += rv; + + return ret; +} +#endif + diff --git a/board/isee/igep0033/board.h b/board/isee/igep0033/board.h new file mode 100644 index 00000000000..37988e0fd33 --- /dev/null +++ b/board/isee/igep0033/board.h @@ -0,0 +1,27 @@ +/* + * IGEP COM AQUILA/CYGNUS boards information header + * + * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * We must be able to enable uart0, for initial output. We then have a + * main pinmux function that can be overridden to enable all other pinmux that + * is required on the board. + */ +void enable_uart0_pin_mux(void); +void enable_board_pin_mux(void); +#endif diff --git a/board/isee/igep0033/mux.c b/board/isee/igep0033/mux.c new file mode 100644 index 00000000000..16f4addf3dd --- /dev/null +++ b/board/isee/igep0033/mux.c @@ -0,0 +1,89 @@ +/* + * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include "board.h" + +static struct module_pin_mux uart0_pin_mux[] = { + {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */ + {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */ + {-1}, +}; + +static struct module_pin_mux mmc0_pin_mux[] = { + {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */ + {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */ + {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */ + {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */ + {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */ + {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */ + {OFFSET(mcasp0_aclkx), (MODE(4) | RXACTIVE)}, /* MMC0_CD */ + {-1}, +}; + +static struct module_pin_mux nand_pin_mux[] = { + {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */ + {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */ + {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */ + {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */ + {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */ + {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */ + {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */ + {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */ + {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */ + {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */ + {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */ + {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */ + {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */ + {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */ + {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */ + {-1}, +}; + +static struct module_pin_mux rmii1_pin_mux[] = { + {OFFSET(mii1_txen), MODE(1)}, /* RMII1_TXEN */ + {OFFSET(mii1_rxerr), MODE(1) | RXACTIVE}, /* RMII1_RXERR */ + {OFFSET(mii1_crs), MODE(1) | RXACTIVE}, /* RMII1_CRS_DV */ + {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE}, /* RMII1_RXD0 */ + {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE}, /* RMII1_RXD1 */ + {OFFSET(mii1_txd0), MODE(1)}, /* RMII1_TXD0 */ + {OFFSET(mii1_txd1), MODE(1)}, /* RMII1_TXD1 */ + {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE}, /* RMII1_REF_CLK */ + {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */ + {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ + {-1}, +}; + +void enable_uart0_pin_mux(void) +{ + configure_module_pin_mux(uart0_pin_mux); +} + +/* + * Do board-specific muxes. + */ +void enable_board_pin_mux(void) +{ + /* NAND Flash */ + configure_module_pin_mux(nand_pin_mux); + /* SD Card */ + configure_module_pin_mux(mmc0_pin_mux); + /* Ethernet pinmux. */ + configure_module_pin_mux(rmii1_pin_mux); +} + diff --git a/boards.cfg b/boards.cfg index 31483d623fb..06ba9795fab 100644 --- a/boards.cfg +++ b/boards.cfg @@ -277,6 +277,7 @@ igep0020_nand arm armv7 igep00x0 isee igep0030 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_ONENAND igep0030_nand arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0030,BOOT_NAND igep0032 arm armv7 igep00x0 isee omap3 igep00x0:MACH_TYPE=MACH_TYPE_IGEP0032,BOOT_ONENAND +igep0033 arm armv7 igep0033 isee am33xx am3517_evm arm armv7 am3517evm logicpd omap3 mt_ventoux arm armv7 mt_ventoux teejet omap3 omap3_zoom1 arm armv7 zoom1 logicpd omap3 diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h new file mode 100644 index 00000000000..50eafdf60b6 --- /dev/null +++ b/include/configs/igep0033.h @@ -0,0 +1,284 @@ +/* + * Copyright (C) 2013, ISEE 2007 SL - http://www.isee.biz/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __CONFIG_IGEP0033_H +#define __CONFIG_IGEP0033_H + +#define CONFIG_AM33XX + +#include + +/* Mach type */ +#define MACH_TYPE_IGEP0033 4521 /* Until the next sync */ +#define CONFIG_MACH_TYPE MACH_TYPE_IGEP0033 + +/* Clock defines */ +#define V_OSCK 24000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +/* DMA defines */ +#define CONFIG_DMA_COHERENT +#define CONFIG_DMA_COHERENT_SIZE (1 << 20) + +#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT "U-Boot# " +#define CONFIG_SYS_NO_FLASH + +/* Display cpuinfo */ +#define CONFIG_DISPLAY_CPUINFO + +/* Commands to include */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FS_GENERIC +#define CONFIG_CMD_MMC +#define CONFIG_CMD_MTDPARTS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS + +/* + * Because the issues explained in doc/README.memory-test, the "mtest command + * is considered deprecated. It should not be enabled in most normal ports of + * U-Boot. + */ +#undef CONFIG_CMD_MEMTEST + +#define CONFIG_BOOTDELAY 1 /* negative for no autoboot */ +#define CONFIG_ENV_VARS_UBOOT_CONFIG +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80200000\0" \ + "rdaddr=0x81000000\0" \ + "bootfile=/boot/uImage\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 rw\0" \ + "mmcrootfstype=ext4 rootwait\0" \ + "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=${rdaddr},64M\0" \ + "ramrootfstype=ext2\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t $loadaddr $filesize\0" \ + "ramargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${ramroot} " \ + "rootfstype=${ramrootfstype}\0" \ + "loadramdisk=load mmc ${mmcdev} ${rdaddr} ramdisk.gz\0" \ + "loaduimagefat=load mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \ + "loaduimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootfile}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" \ + "ramboot=echo Booting from ramdisk ...; " \ + "run ramargs; " \ + "bootm ${loadaddr}\0" \ + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loaduimage; then " \ + "run mmcboot;" \ + "fi;" \ + "fi;" \ + +/* Max number of command args */ +#define CONFIG_SYS_MAXARGS 16 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 512 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */ +#define CONFIG_SYS_HZ 1000 /* 1ms clock */ + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ +#define PHYS_DRAM_1 0x80000000 /* DRAM Bank #1 */ +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_DRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) +/* Platform/Board specific defs */ +#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK (48000000) +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ + +#define CONFIG_SERIAL_MULTI +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_SYS_CONSOLE_INFO_QUIET + +/* MMC support */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_DOS_PARTITION + +/* GPIO support */ +#define CONFIG_OMAP_GPIO + +/* Ethernet support */ +#define CONFIG_DRIVER_TI_CPSW +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 0 +#define CONFIG_PHY_SMSC + +/* NAND support */ +#define CONFIG_NAND +#define CONFIG_NAND_OMAP_GPMC +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_ONFI_DETECTION 1 +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */ + +#define CONFIG_MTD_PARTITIONS +#define CONFIG_MTD_DEVICE +#define CONFIG_RBTREE +#define CONFIG_LZO + +#define MTDIDS_DEFAULT "nand0=nand" +#define MTDPARTS_DEFAULT "mtdparts=nand:512k(SPL),"\ + "1m(U-Boot),128k(U-Boot Env),"\ + "5m(Kernel),-(File System)" + +/* Unsupported features */ +#undef CONFIG_USE_IRQ + +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x402F0400 +#define CONFIG_SPL_MAX_SIZE (101 * 1024) +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_YMODEM_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_NAND_AM33XX_BCH +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_ECCSTEPS 4 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ + CONFIG_SYS_NAND_ECCSTEPS) + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80800000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 + +/* + * Since SPL did pll and ddr initialization for us, + * we don't need to do it twice. + */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif + +#endif /* ! __CONFIG_IGEP0033_H */ -- cgit v1.3.1 From 85b7ac4588c3128e3702f7232b3fd46c7cd7cf43 Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Thu, 11 Apr 2013 05:22:10 +0000 Subject: omap5_common: Add optargs variable for kernel command line args Add 'optargs' variable to be set to additional kernel arguments, similar to omap3*/am3* usage. Cc: Sricharan R Signed-off-by: Tom Rini --- include/configs/omap5_common.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h index c21c387cba8..7528f4c0b16 100644 --- a/include/configs/omap5_common.h +++ b/include/configs/omap5_common.h @@ -150,10 +150,12 @@ "usbtty=cdc_acm\0" \ "vram=16M\0" \ "partitions=" PARTS_DEFAULT "\0" \ + "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext4 rootwait\0" \ "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ "vram=${vram} " \ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype}\0" \ -- cgit v1.3.1 From 15191c91a240bd8683ca40e6c4b8b8c44b98412f Mon Sep 17 00:00:00 2001 From: Mark Jackson Date: Wed, 17 Apr 2013 08:22:47 +0000 Subject: Remove duplicate / unused #defines on AM335x boards As part of a review of a recent patch to add a new AM335x board, Tom found several duplicate and/or unused #defines. This patch simply removes them. The two affected configs have been recompiled to check nothing was broken (from a compilation point of view !!) Reported-by: Tom Rini Signed-off-by: Mark Jackson --- include/configs/am335x_evm.h | 10 ++-------- include/configs/pcm051.h | 4 +--- 2 files changed, 3 insertions(+), 11 deletions(-) (limited to 'include') diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index ef00306a55e..5739422c4c1 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -196,7 +196,6 @@ + (8 * 1024 * 1024)) #define CONFIG_SYS_LOAD_ADDR 0x81000000 /* Default load address */ -#define CONFIG_SYS_HZ 1000 /* 1ms clock */ #define CONFIG_MMC #define CONFIG_GENERIC_MMC @@ -260,12 +259,11 @@ /* Platform/Board specific defs */ #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_HZ 1000 /* 1ms clock */ /* NS16550 Configuration */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SERIAL_MULTI #define CONFIG_SYS_NS16550_REG_SIZE (-4) #define CONFIG_SYS_NS16550_CLK (48000000) #define CONFIG_SYS_NS16550_COM1 0x44e09000 /* Base EVM has UART0 */ @@ -360,11 +358,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 14 -#define CONFIG_SYS_NAND_ECCSTEPS 4 -#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \ - CONFIG_SYS_NAND_ECCSTEPS) - -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index d0ea74e0b48..2e3f08b5b6d 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -129,7 +129,6 @@ + (8 * 1024 * 1024)) #define CONFIG_SYS_LOAD_ADDR 0x80007fc0 /* Default load address */ -#define CONFIG_SYS_HZ 1000 /* 1ms clock */ #define CONFIG_MMC #define CONFIG_GENERIC_MMC @@ -158,13 +157,12 @@ /* Platform/Board specific defs */ #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ -#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_HZ 1000 /* 1ms clock */ #define CONFIG_CONS_INDEX 1 /* NS16550 Configuration */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SERIAL_MULTI #define CONFIG_SYS_NS16550_REG_SIZE (-4) #define CONFIG_SYS_NS16550_CLK (48000000) #define CONFIG_SYS_NS16550_COM1 0x44e09000 /* Base EVM has UART0 */ -- cgit v1.3.1 From 0b1b60c77954df19b5a601e2ba87614f2d0bbb8b Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Wed, 17 Apr 2013 20:49:40 +0000 Subject: ARM: OMAP5: Fix warm reset with USB cable connected Warm reset on OMAP5 freezes when USB cable is connected. Fix requires PRM_RSTTIME.RSTTIME1 to be programmed with the time for which reset should be held low for the voltages and the oscillator to reach stable state. There are 3 parameters to be considered for calculating the time, which are mostly board and PMIC dependent. -1- Time taken by the Oscillator to shut + restart -2- PMIC OTP times -3- Voltage rail ramp times, which inturn depends on the PMIC slew rate and value of the voltage ramp needed. In order to keep the code in u-boot simple, have a way for boards to specify a pre computed time directly using the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' option. If boards fail to specify the time, use a default as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead. Using the default value translates into some ~22ms and should work in all cases. However in order to avoid this large delay hiding other bugs, its recommended that all boards look at their respective data sheets and specify a pre computed and optimal value using 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC' In order to help future board additions to compute this config option value, add a README at doc/README.omap-reset-time which explains how to compute the value. Also update the toplevel README with the additional option and pointers to doc/README.omap-reset-time. Signed-off-by: Lokesh Vutla [rnayak@ti.com: Updated changelog and added the README] Signed-off-by: Rajendra Nayak --- README | 4 ++++ arch/arm/cpu/armv7/omap-common/clocks-common.c | 1 + arch/arm/cpu/armv7/omap-common/reset.c | 4 ++++ arch/arm/cpu/armv7/omap5/hwinit.c | 19 +++++++++++++++++++ arch/arm/cpu/armv7/omap5/prcm-regs.c | 2 ++ arch/arm/include/asm/arch-omap4/sys_proto.h | 1 + arch/arm/include/asm/arch-omap5/clocks.h | 10 ++++++++++ arch/arm/include/asm/arch-omap5/sys_proto.h | 10 ++++++++++ arch/arm/include/asm/omap_common.h | 1 + doc/README.omap-reset-time | 20 ++++++++++++++++++++ include/configs/omap5_uevm.h | 1 + 11 files changed, 73 insertions(+) create mode 100644 doc/README.omap-reset-time (limited to 'include') diff --git a/README b/README index 0bc0af57006..453189156c8 100644 --- a/README +++ b/README @@ -3323,6 +3323,10 @@ Configuration Settings: offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than directly. You should not need to touch this setting. +- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only) + This is set by OMAP boards for the max time that reset should + be asserted. See doc/README.omap-reset-time for details on how + the value can be calulated on a given board. The following definitions that deal with the placement and management of environment data (variable area); in general, we support the diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 2b955c7c006..99910cdcb0b 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -716,6 +716,7 @@ void prcm_init(void) setup_non_essential_dplls(); enable_non_essential_clocks(); #endif + setup_warmreset_time(); break; default: break; diff --git a/arch/arm/cpu/armv7/omap-common/reset.c b/arch/arm/cpu/armv7/omap-common/reset.c index 587bb47745a..57ea9d99995 100644 --- a/arch/arm/cpu/armv7/omap-common/reset.c +++ b/arch/arm/cpu/armv7/omap-common/reset.c @@ -39,3 +39,7 @@ u32 __weak warm_reset(void) { return (readl(PRM_RSTST) & PRM_RSTST_WARM_RESET_MASK); } + +void __weak setup_warmreset_time(void) +{ +} diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c index 2f4b24752b2..d29df787206 100644 --- a/arch/arm/cpu/armv7/omap5/hwinit.c +++ b/arch/arm/cpu/armv7/omap5/hwinit.c @@ -363,3 +363,22 @@ u32 warm_reset(void) { return readl((*prcm)->prm_rstst) & PRM_RSTST_WARM_RESET_MASK; } + +void setup_warmreset_time(void) +{ + u32 rst_time, rst_val; + +#ifndef CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC + rst_time = CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC; +#else + rst_time = CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC; +#endif + rst_time = usec_to_32k(rst_time) << RSTTIME1_SHIFT; + + if (rst_time > RSTTIME1_MASK) + rst_time = RSTTIME1_MASK; + + rst_val = readl((*prcm)->prm_rsttime) & ~RSTTIME1_MASK; + rst_val |= rst_time; + writel(rst_val, (*prcm)->prm_rsttime); +} diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c index b8a61fe8813..e9f6a326539 100644 --- a/arch/arm/cpu/armv7/omap5/prcm-regs.c +++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c @@ -729,6 +729,7 @@ struct prcm_regs const omap5_es2_prcm = { .cm_wkupaon_io_srcomp_clkctrl = 0x4ae07998, .prm_rstctrl = 0x4ae07c00, .prm_rstst = 0x4ae07c04, + .prm_rsttime = 0x4ae07c08, .prm_vc_val_bypass = 0x4ae07ca0, .prm_vc_cfg_i2c_mode = 0x4ae07cb4, .prm_vc_cfg_i2c_clk = 0x4ae07cb8, @@ -952,6 +953,7 @@ struct prcm_regs const dra7xx_prcm = { .cm_wkupaon_scrm_clkctrl = 0x4ae07890, .prm_rstctrl = 0x4ae07d00, .prm_rstst = 0x4ae07d04, + .prm_rsttime = 0x4ae07d08, .prm_vc_val_bypass = 0x4ae07da0, .prm_vc_cfg_i2c_mode = 0x4ae07db4, .prm_vc_cfg_i2c_clk = 0x4ae07db8, diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index d5f1868eeed..ac9c1f83ed7 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -58,6 +58,7 @@ void omap_vc_init(u16 speed_khz); int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); +void setup_warmreset_time(void); /* * This is used to verify if the configuration header * was executed by Romcode prior to control of transfer diff --git a/arch/arm/include/asm/arch-omap5/clocks.h b/arch/arm/include/asm/arch-omap5/clocks.h index cfde3743330..68afa766960 100644 --- a/arch/arm/include/asm/arch-omap5/clocks.h +++ b/arch/arm/include/asm/arch-omap5/clocks.h @@ -190,6 +190,10 @@ #define OPTFCLKEN_SRCOMP_FCLK_SHIFT 8 #define OPTFCLKEN_SRCOMP_FCLK_MASK (1 << 8) +/* PRM_RSTTIME */ +#define RSTTIME1_SHIFT 0 +#define RSTTIME1_MASK (0x3ff << 0) + /* Clock frequencies */ #define OMAP_SYS_CLK_FREQ_38_4_MHZ 38400000 #define OMAP_SYS_CLK_IND_38_4_MHZ 6 @@ -251,4 +255,10 @@ #define DPLL_NO_LOCK 0 #define DPLL_LOCK 1 +/* + * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff. + * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles + * into microsec and passing the value. + */ +#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219 #endif /* _CLOCKS_OMAP5_H_ */ diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h index e66ab44341d..393c8bfdb7a 100644 --- a/arch/arm/include/asm/arch-omap5/sys_proto.h +++ b/arch/arm/include/asm/arch-omap5/sys_proto.h @@ -64,6 +64,7 @@ u32 warm_reset(void); void force_emif_self_refresh(void); void get_ioregs(const struct ctrl_ioregs **regs); void srcomp_enable(void); +void setup_warmreset_time(void); /* * This is used to verify if the configuration header @@ -122,4 +123,13 @@ static inline u32 omap_hw_init_context(void) #endif } +static inline u32 div_round_up(u32 num, u32 den) +{ + return (num + den - 1)/den; +} + +static inline u32 usec_to_32k(u32 usec) +{ + return div_round_up(32768 * usec, 1000000); +} #endif diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index 091ddb508d5..6d377d5b596 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -316,6 +316,7 @@ struct prcm_regs { u32 cm_wkupaon_io_srcomp_clkctrl; u32 prm_rstctrl; u32 prm_rstst; + u32 prm_rsttime; u32 prm_vc_val_bypass; u32 prm_vc_cfg_i2c_mode; u32 prm_vc_cfg_i2c_clk; diff --git a/doc/README.omap-reset-time b/doc/README.omap-reset-time new file mode 100644 index 00000000000..0c974bacae2 --- /dev/null +++ b/doc/README.omap-reset-time @@ -0,0 +1,20 @@ +README on how reset time on OMAPs should be calculated + +CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC: +Most OMAPs' provide a way to specify the time for +which the reset should be held low while the voltages +and Oscillator outputs stabilize. + +This time is mostly board and PMIC dependent. Hence the +boards are expected to specify a pre-computed time +using the above option, (the details on how to compute +the value are given below) without which a default time +as specified by CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC +is used. + +The value for CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC +can be computed using a summation of the below 3 parameters +-1- Time taken by the Osciallator to stop and restart +-2- PMIC OTP time +-3- Voltage ramp time, which can be derived using the +PMIC slew rate and value of voltage ramp needed. diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index c5bf51d9c95..c791789cb75 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -54,4 +54,5 @@ #define CONFIG_SYS_PROMPT "OMAP5430 EVM # " +#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 #endif /* __CONFIG_OMAP5_EVM_H */ -- cgit v1.3.1 From 34f667bbc4819607735dd56df17c8f1789af40d1 Mon Sep 17 00:00:00 2001 From: Dan Murphy Date: Thu, 18 Apr 2013 06:29:53 +0000 Subject: ARM:Panda:Fix device tree loading for the panda-es Fix the device tree loading for panda(4430) and panda-es(4460) Modify the board name if a 4460 panda or panda-es is detected at run time. In the findfdt add a check for the panda-es board name and load the panda-es device tree blob. Signed-off-by: Dan Murphy --- board/ti/panda/panda.c | 6 ++++++ include/configs/omap4_common.h | 4 +++- 2 files changed, 9 insertions(+), 1 deletion(-) (limited to 'include') diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index cab059863d3..2bbe392d811 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -82,6 +82,12 @@ int misc_init_r(void) if (omap_revision() == OMAP4430_ES1_0) return 0; +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + if (omap_revision() >= OMAP4460_ES1_0 || + omap_revision() <= OMAP4460_ES1_1) + setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es")); +#endif + gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO); phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO); diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index 1fd3097d757..68faecacecf 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -176,7 +176,9 @@ "if test $board_name = sdp4430; then " \ "setenv fdtfile omap4-sdp.dtb; fi; " \ "if test $board_name = panda; then " \ - "setenv fdtfile omap4-panda-es.dtb; fi\0" \ + "setenv fdtfile omap4-panda.dtb; fi;" \ + "if test $board_name = panda-es; then " \ + "setenv fdtfile omap4-panda-es.dtb; fi; \0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ #define CONFIG_BOOTCOMMAND \ -- cgit v1.3.1 From 584506bee694643214152ed2bec9a99df9a244d6 Mon Sep 17 00:00:00 2001 From: Dan Murphy Date: Thu, 18 Apr 2013 06:29:54 +0000 Subject: ARM: Panda: Add flag to allow runtime enviroment varibale mods Add the flag to allow runtime enviroment variable modifications. This is being added so that the board-name can be modified at runtime to indicate either a panda(4430) or a panda-es(4460) Signed-off-by: Dan Murphy --- include/configs/omap4_panda.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h index eacb5f5c3b7..abf586b872a 100644 --- a/include/configs/omap4_panda.h +++ b/include/configs/omap4_panda.h @@ -66,4 +66,6 @@ #define CONFIG_SYS_PROMPT "Panda # " +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + #endif /* __CONFIG_PANDA_H */ -- cgit v1.3.1 From 0b800a6b267de24466ca5a463db6497d7362f128 Mon Sep 17 00:00:00 2001 From: Igor Grinberg Date: Mon, 22 Apr 2013 01:06:55 +0000 Subject: cm-t35: update config file Several minor updates to the cm-t35 config file. Signed-off-by: Igor Grinberg Tested-by: Nikita Kiryanov --- include/configs/cm_t35.h | 18 +++++------------- 1 file changed, 5 insertions(+), 13 deletions(-) (limited to 'include') diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index 726714dd211..c6e357a8ceb 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -135,12 +135,12 @@ #define CONFIG_CMD_CACHE #define CONFIG_CMD_EXT2 /* EXT2 Support */ #define CONFIG_CMD_FAT /* FAT support */ -#define CONFIG_CMD_JFFS2 /* JFFS2 Support */ #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_MTD_PARTITIONS #define MTDIDS_DEFAULT "nand0=nand" #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ - "1920k(u-boot),128k(u-boot-env),"\ + "1920k(u-boot),256k(u-boot-env),"\ "4m(kernel),-(fs)" #define CONFIG_CMD_I2C /* I2C serial bus support */ @@ -182,14 +182,6 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ -#define CONFIG_JFFS2_NAND -/* nand device jffs2 lives on */ -#define CONFIG_JFFS2_DEV "nand0" -/* start of jffs2 partition */ -#define CONFIG_JFFS2_PART_OFFSET 0x680000 -#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */ - /* partition */ - /* Environment information */ #define CONFIG_BOOTDELAY 10 #define CONFIG_ZERO_BOOTDELAY_CHECK @@ -204,9 +196,9 @@ "defaultdisplay=dvi\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ - "mmcrootfstype=ext3 rootwait\0" \ + "mmcrootfstype=ext4 rootwait\0" \ "nandroot=/dev/mtdblock4 rw\0" \ - "nandrootfstype=jffs2\0" \ + "nandrootfstype=ubifs\0" \ "mmcargs=setenv bootargs console=${console} " \ "mpurate=${mpurate} " \ "vram=${vram} " \ @@ -232,7 +224,7 @@ "bootm ${loadaddr}\0" \ "nandboot=echo Booting from nand ...; " \ "run nandargs; " \ - "nand read ${loadaddr} 280000 400000; " \ + "nand read ${loadaddr} 2a0000 400000; " \ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ -- cgit v1.3.1 From 34fa07063a7f5fc437bcaa71156182bb3bf2f516 Mon Sep 17 00:00:00 2001 From: Eric Benard Date: Mon, 22 Apr 2013 05:55:00 +0000 Subject: davinci: handle CONFIG_SYS_CLE_MASK and CONFIG_SYS_ALE_MASK MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit these variables are curently defined in several config files but the driver doesn't use them and defaults to hardcoded values in nand_defs.h It's interesting to be able to change this hardcoded valude when the hardware is not using the default adress signals to drive ALE and CLE and two configuration defines already exist for this purpose so use them. Signed-off-by: Eric Bénard --- arch/arm/include/asm/arch-davinci/nand_defs.h | 9 +++++++++ include/configs/da830evm.h | 4 ++-- include/configs/da850evm.h | 4 ++-- include/configs/enbw_cmc.h | 4 ++-- include/configs/tnetv107x_evm.h | 4 ++-- 5 files changed, 17 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/arch/arm/include/asm/arch-davinci/nand_defs.h b/arch/arm/include/asm/arch-davinci/nand_defs.h index 10f3a392aba..4a30813808a 100644 --- a/arch/arm/include/asm/arch-davinci/nand_defs.h +++ b/arch/arm/include/asm/arch-davinci/nand_defs.h @@ -36,6 +36,15 @@ #define MASK_ALE 0x08 #endif +#ifdef CONFIG_SYS_NAND_MASK_CLE +#undef MASK_CLE +#define MASK_CLE CONFIG_SYS_NAND_MASK_CLE +#endif +#ifdef CONFIG_SYS_NAND_MASK_ALE +#undef MASK_ALE +#define MASK_ALE CONFIG_SYS_NAND_MASK_ALE +#endif + #define NAND_READ_START 0x00 #define NAND_READ_END 0x30 #define NAND_STATUS 0x70 diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h index f7ac256a0fa..198892ba571 100644 --- a/include/configs/da830evm.h +++ b/include/configs/da830evm.h @@ -109,8 +109,8 @@ #define CONFIG_SYS_NAND_CS 3 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE #define CONFIG_SYS_NAND_PAGE_2K -#define CONFIG_SYS_CLE_MASK 0x10 -#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #endif diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index 583568d309a..c420967411d 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -199,8 +199,8 @@ #define CONFIG_SYS_NAND_PAGE_2K #define CONFIG_SYS_NAND_CS 3 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE -#define CONFIG_SYS_CLE_MASK 0x10 -#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 #undef CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST diff --git a/include/configs/enbw_cmc.h b/include/configs/enbw_cmc.h index 2d63b670cd7..97bc9729a1b 100644 --- a/include/configs/enbw_cmc.h +++ b/include/configs/enbw_cmc.h @@ -118,8 +118,8 @@ #define CONFIG_SYS_NAND_PAGE_2K #define CONFIG_SYS_NAND_CS 3 #define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE -#define CONFIG_SYS_CLE_MASK 0x10 -#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 #undef CONFIG_SYS_NAND_HW_ECC #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ diff --git a/include/configs/tnetv107x_evm.h b/include/configs/tnetv107x_evm.h index d6371fce4d0..cabc06e5ba6 100644 --- a/include/configs/tnetv107x_evm.h +++ b/include/configs/tnetv107x_evm.h @@ -82,8 +82,8 @@ #define CONFIG_SYS_NAND_CS 2 #define CONFIG_SYS_NAND_USE_FLASH_BBT #define CONFIG_SYS_NAND_BASE TNETV107X_ASYNC_EMIF_DATA_CE0_BASE -#define CONFIG_SYS_CLE_MASK 0x10 -#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_MASK_CLE 0x10 +#define CONFIG_SYS_NAND_MASK_ALE 0x8 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_MTD_PARTITIONS #define CONFIG_CMD_MTDPARTS -- cgit v1.3.1 From 4a0eb75752167bef51993307a10677295cef315b Mon Sep 17 00:00:00 2001 From: SRICHARAN R Date: Wed, 24 Apr 2013 00:41:24 +0000 Subject: ARM: OMAP: Cleanup boot parameters usage The boot parameters are read from individual variables assigned for each of them. This been corrected and now they are stored as a part of the global data 'gd' structure. So read them from 'gd' instead. Signed-off-by: Sricharan R [trini: Add igep0033 hunk] Signed-off-by: Tom Rini --- arch/arm/cpu/armv7/lowlevel_init.S | 8 ++++- arch/arm/cpu/armv7/omap-common/boot-common.c | 31 ++++++++-------- arch/arm/cpu/armv7/omap-common/lowlevel_init.S | 50 ++------------------------ arch/arm/include/asm/arch-omap4/sys_proto.h | 11 ++---- arch/arm/include/asm/arch-omap5/sys_proto.h | 12 ++----- arch/arm/include/asm/omap_common.h | 3 ++ common/spl/spl.c | 10 ++---- include/configs/am335x_evm.h | 1 + include/configs/igep0033.h | 1 + include/configs/pcm051.h | 1 + include/configs/ti814x_evm.h | 1 + include/spl.h | 1 - 12 files changed, 39 insertions(+), 91 deletions(-) (limited to 'include') diff --git a/arch/arm/cpu/armv7/lowlevel_init.S b/arch/arm/cpu/armv7/lowlevel_init.S index 0d45528e999..0a15aa4671b 100644 --- a/arch/arm/cpu/armv7/lowlevel_init.S +++ b/arch/arm/cpu/armv7/lowlevel_init.S @@ -37,7 +37,13 @@ ENTRY(lowlevel_init) */ ldr sp, =CONFIG_SYS_INIT_SP_ADDR bic sp, sp, #7 /* 8-byte alignment for ABI compliance */ - +#ifdef CONFIG_SPL_BUILD + ldr r8, =gdata +#else + sub sp, #GD_SIZE + bic sp, sp, #7 + mov r8, sp +#endif /* * Save the old lr(passed in ip) and the current lr to stack */ diff --git a/arch/arm/cpu/armv7/omap-common/boot-common.c b/arch/arm/cpu/armv7/omap-common/boot-common.c index 24cbe2da05d..bff7e9c82a1 100644 --- a/arch/arm/cpu/armv7/omap-common/boot-common.c +++ b/arch/arm/cpu/armv7/omap-common/boot-common.c @@ -23,31 +23,17 @@ #include #include -/* - * This is used to verify if the configuration header - * was executed by rom code prior to control of transfer - * to the bootloader. SPL is responsible for saving and - * passing the boot_params pointer to the u-boot. - */ -struct omap_boot_parameters boot_params __attribute__ ((section(".data"))); +DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_SPL_BUILD -/* - * We use static variables because global data is not ready yet. - * Initialized data is available in SPL right from the beginning. - * We would not typically need to save these parameters in regular - * U-Boot. This is needed only in SPL at the moment. - */ -u32 omap_bootmode = MMCSD_MODE_FAT; - u32 spl_boot_device(void) { - return (u32) (boot_params.omap_bootdevice); + return (u32) (gd->arch.omap_boot_params.omap_bootdevice); } u32 spl_boot_mode(void) { - return omap_bootmode; + return gd->arch.omap_boot_params.omap_bootmode; } void spl_board_init(void) @@ -73,4 +59,15 @@ int board_mmc_init(bd_t *bis) } return 0; } + +void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image) +{ + typedef void __noreturn (*image_entry_noargs_t)(u32 *); + image_entry_noargs_t image_entry = + (image_entry_noargs_t) spl_image->entry_point; + + debug("image entry point: 0x%X\n", spl_image->entry_point); + /* Pass the saved boot_params from rom code */ + image_entry((u32 *)&gd->arch.omap_boot_params); +} #endif diff --git a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S index 90b3c8aea4e..c4895369bfb 100644 --- a/arch/arm/cpu/armv7/omap-common/lowlevel_init.S +++ b/arch/arm/cpu/armv7/omap-common/lowlevel_init.S @@ -28,59 +28,13 @@ #include #include +#include #include #include ENTRY(save_boot_params) - /* - * See if the rom code passed pointer is valid: - * It is not valid if it is not in non-secure SRAM - * This may happen if you are booting with the help of - * debugger - */ - ldr r2, =NON_SECURE_SRAM_START - cmp r2, r0 - bgt 1f - ldr r2, =NON_SECURE_SRAM_END - cmp r2, r0 - blt 1f - - /* - * store the boot params passed from rom code or saved - * and passed by SPL - */ - cmp r0, #0 - beq 1f - ldr r1, =boot_params + ldr r1, =OMAP_SRAM_SCRATCH_BOOT_PARAMS str r0, [r1] -#ifdef CONFIG_SPL_BUILD - /* Store the boot device in spl_boot_device */ - ldrb r2, [r0, #BOOT_DEVICE_OFFSET] @ r1 <- value of boot device - and r2, #BOOT_DEVICE_MASK - ldr r3, =boot_params - strb r2, [r3, #BOOT_DEVICE_OFFSET] @ spl_boot_device <- r1 - - /* - * boot mode is only valid for device that can be raw or FAT booted. - * in other cases it may be fatal to look. While platforms differ - * in the values used for each MMC slot, they are contiguous. - */ - cmp r2, #MMC_BOOT_DEVICES_START - blt 2f - cmp r2, #MMC_BOOT_DEVICES_END - bgt 2f - /* Store the boot mode (raw/FAT) in omap_bootmode */ - ldr r2, [r0, #DEV_DESC_PTR_OFFSET] @ get the device descriptor ptr - ldr r2, [r2, #DEV_DATA_PTR_OFFSET] @ get the pDeviceData ptr - ldr r2, [r2, #BOOT_MODE_OFFSET] @ get the boot mode - ldr r3, =omap_bootmode - str r2, [r3] -#endif -2: - ldrb r2, [r0, #CH_FLAGS_OFFSET] - ldr r3, =boot_params - strb r2, [r3, #CH_FLAGS_OFFSET] -1: bx lr ENDPROC(save_boot_params) diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h index ac9c1f83ed7..039a1f2604f 100644 --- a/arch/arm/include/asm/arch-omap4/sys_proto.h +++ b/arch/arm/include/asm/arch-omap4/sys_proto.h @@ -27,6 +27,8 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + struct omap_sysinfo { char *board_string; }; @@ -59,13 +61,6 @@ int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data); u32 warm_reset(void); void force_emif_self_refresh(void); void setup_warmreset_time(void); -/* - * This is used to verify if the configuration header - * was executed by Romcode prior to control of transfer - * to the bootloader. SPL is responsible for saving and - * passing this to the u-boot. - */ -extern struct omap_boot_parameters boot_params; static inline u32 running_from_sdram(void) { @@ -85,7 +80,7 @@ static inline u8 uboot_loaded_by_spl(void) * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a * mandatory section if CH is present. */ - if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS)) + if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS)) return 0; else return running_from_sdram(); diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h index 393c8bfdb7a..b79161d79ab 100644 --- a/arch/arm/include/asm/arch-omap5/sys_proto.h +++ b/arch/arm/include/asm/arch-omap5/sys_proto.h @@ -27,6 +27,8 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + struct pad_conf_entry { u32 offset; u32 val; @@ -66,14 +68,6 @@ void get_ioregs(const struct ctrl_ioregs **regs); void srcomp_enable(void); void setup_warmreset_time(void); -/* - * This is used to verify if the configuration header - * was executed by Romcode prior to control of transfer - * to the bootloader. SPL is responsible for saving and - * passing this to the u-boot. - */ -extern struct omap_boot_parameters boot_params; - static inline u32 running_from_sdram(void) { u32 pc; @@ -92,7 +86,7 @@ static inline u8 uboot_loaded_by_spl(void) * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a * mandatory section if CH is present. */ - if ((boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS)) + if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS)) return 0; else return running_from_sdram(); diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h index eebc9c7cbf1..ee7b188d3a5 100644 --- a/arch/arm/include/asm/omap_common.h +++ b/arch/arm/include/asm/omap_common.h @@ -25,6 +25,8 @@ #ifndef _OMAP_COMMON_H_ #define _OMAP_COMMON_H_ +#ifndef __ASSEMBLY__ + #include #define NUM_SYS_CLKS 8 @@ -558,6 +560,7 @@ static inline u32 omap_revision(void) extern u32 *const omap_si_rev; return *omap_si_rev; } +#endif /* * silicon revisions. diff --git a/common/spl/spl.c b/common/spl/spl.c index 6715e0d203a..e6aa89bdd00 100644 --- a/common/spl/spl.c +++ b/common/spl/spl.c @@ -125,17 +125,13 @@ void spl_parse_image_header(const struct image_header *header) __weak void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image) { - typedef void __noreturn (*image_entry_noargs_t)(u32 *); + typedef void __noreturn (*image_entry_noargs_t)(void); + image_entry_noargs_t image_entry = (image_entry_noargs_t) spl_image->entry_point; debug("image entry point: 0x%X\n", spl_image->entry_point); - /* Pass the saved boot_params from rom code */ -#if defined(CONFIG_VIRTIO) || defined(CONFIG_ZEBU) - image_entry = (image_entry_noargs_t)0x80100000; -#endif - u32 boot_params_ptr_addr = (u32)&boot_params_ptr; - image_entry((u32 *)boot_params_ptr_addr); + image_entry(); } #ifdef CONFIG_SPL_RAM_DEVICE diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 5739422c4c1..941054d70a0 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -17,6 +17,7 @@ #define __CONFIG_AM335X_EVM_H #define CONFIG_AM33XX +#define CONFIG_OMAP #include diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h index 50eafdf60b6..14063a83e6a 100644 --- a/include/configs/igep0033.h +++ b/include/configs/igep0033.h @@ -15,6 +15,7 @@ #define __CONFIG_IGEP0033_H #define CONFIG_AM33XX +#define CONFIG_OMAP #include diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 2e3f08b5b6d..cc8d3171998 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -20,6 +20,7 @@ #define __CONFIG_PCM051_H #define CONFIG_AM33XX +#define CONFIG_OMAP #include diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index e646bd72350..6c423df372e 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -19,6 +19,7 @@ #define CONFIG_TI81XX #define CONFIG_TI814X #define CONFIG_SYS_NO_FLASH +#define CONFIG_OMAP #include diff --git a/include/spl.h b/include/spl.h index b40be8039c0..4bc1dd13bbc 100644 --- a/include/spl.h +++ b/include/spl.h @@ -44,7 +44,6 @@ struct spl_image_info { #define SPL_COPY_PAYLOAD_ONLY 1 extern struct spl_image_info spl_image; -extern u32 *boot_params_ptr; /* SPL common functions */ void preloader_console_init(void); -- cgit v1.3.1 From 47c6ea076eb51e624f8744d93db5cd70b97dc25d Mon Sep 17 00:00:00 2001 From: SRICHARAN R Date: Wed, 24 Apr 2013 00:41:25 +0000 Subject: ARM: OMAP: Add arch_cpu_init function The boot parameters passed from SPL to UBOOT must be saved as a part of uboot's gd data as early as possible, before we will inadvertently overwrite it. So adding a arch_cpu_init for the required Socs to save it. Signed-off-by: Sricharan R [trini: Add igep0033 hunk] Signed-off-by: Tom Rini --- arch/arm/cpu/armv7/omap-common/hwinit-common.c | 11 +++++++++++ include/configs/am335x_evm.h | 3 +++ include/configs/igep0033.h | 3 +++ include/configs/omap4_common.h | 4 ++++ include/configs/omap5_common.h | 3 +++ include/configs/pcm051.h | 3 +++ include/configs/ti814x_evm.h | 3 +++ 7 files changed, 30 insertions(+) (limited to 'include') diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c index c7107847c4f..1645120de7a 100644 --- a/arch/arm/cpu/armv7/omap-common/hwinit-common.c +++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c @@ -147,6 +147,17 @@ static void save_omap_boot_params(void) } } +#ifdef CONFIG_ARCH_CPU_INIT +/* + * SOC specific cpu init + */ +int arch_cpu_init(void) +{ + save_omap_boot_params(); + return 0; +} +#endif /* CONFIG_ARCH_CPU_INIT */ + /* * Routine: s_init * Description: Does early system init of watchdog, muxing, andclocks diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 941054d70a0..f019134216a 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -294,6 +294,9 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 110, 300, 600, 1200, 2400, \ 4800, 9600, 14400, 19200, 28800, 38400, 56000, 57600, 115200 } +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + #define CONFIG_ENV_OVERWRITE 1 #define CONFIG_SYS_CONSOLE_INFO_QUIET diff --git a/include/configs/igep0033.h b/include/configs/igep0033.h index 14063a83e6a..1912d7df376 100644 --- a/include/configs/igep0033.h +++ b/include/configs/igep0033.h @@ -157,6 +157,9 @@ #define CONFIG_CONS_INDEX 1 #define CONFIG_BAUDRATE 115200 +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + #define CONFIG_ENV_OVERWRITE 1 #define CONFIG_SYS_CONSOLE_INFO_QUIET diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index 68faecacecf..d6448b0529e 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -87,6 +87,10 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} + +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + /* I2C */ #define CONFIG_HARD_I2C 1 #define CONFIG_SYS_I2C_SPEED 100000 diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h index 7528f4c0b16..deb5e9fd5e6 100644 --- a/include/configs/omap5_common.h +++ b/include/configs/omap5_common.h @@ -86,6 +86,9 @@ #define CONFIG_BAUDRATE 115200 +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + /* I2C */ #define CONFIG_HARD_I2C #define CONFIG_SYS_I2C_SPEED 100000 diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index cc8d3171998..478f805b7c5 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -193,6 +193,9 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 110, 300, 600, 1200, 2400, \ 4800, 9600, 14400, 19200, 28800, 38400, 56000, 57600, 115200 } +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_INFO_QUIET diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h index 6c423df372e..eac5ad02434 100644 --- a/include/configs/ti814x_evm.h +++ b/include/configs/ti814x_evm.h @@ -163,6 +163,9 @@ #define CONFIG_BAUDRATE 115200 +/* CPU */ +#define CONFIG_ARCH_CPU_INIT + #define CONFIG_ENV_OVERWRITE #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_CONSOLE_INFO_QUIET -- cgit v1.3.1