From 1a0ce20aa4cb4e3068da04e7290ee9986fd0b834 Mon Sep 17 00:00:00 2001 From: Martin Krause Date: Wed, 24 Oct 2007 08:42:25 +0200 Subject: TQM5200: fix spurious characters on second serial interface With this patch PSC3 is configured as UART. This is done, because if the pins of PSC3 are not configured at all (-> all pins are GPI), due to crosstalk, spurious characters may be send over the RX232_2_TXD signal line. Signed-off-by: Martin Krause Signed-off-by: Grant Likely --- include/configs/TQM5200.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index d55340404d8..c3f16f524ef 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -547,7 +547,7 @@ # if defined (CONFIG_TQM5200_REV100) # error TQM5200 REV100 not supported on STK52XX REV200 or above # else/* TQM5200 REV200 and above */ -# define CFG_GPS_PORT_CONFIG 0x91500004 +# define CFG_GPS_PORT_CONFIG 0x91500404 # endif # endif #elif defined (CONFIG_FO300) -- cgit v1.3.1 From 2acefa72ee0026f862ab65597ca687428f63a973 Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:09:17 -0500 Subject: ColdFire 5282: Fix external flash boot and return dramsize Signed-off-by: TsiChungLiew --- board/m5282evb/m5282evb.c | 1 + cpu/mcf52x2/start.S | 6 +++++- include/configs/M5282EVB.h | 2 +- 3 files changed, 7 insertions(+), 2 deletions(-) (limited to 'include') diff --git a/board/m5282evb/m5282evb.c b/board/m5282evb/m5282evb.c index 243d6a4d83e..7d6d1d6231a 100644 --- a/board/m5282evb/m5282evb.c +++ b/board/m5282evb/m5282evb.c @@ -89,4 +89,5 @@ long int initdram (int board_type) /* Write to the SDRAM Mode Register */ *(u32 *)(CFG_SDRAM_BASE + 0x400) = 0xA5A59696; } + return dramsize; } diff --git a/cpu/mcf52x2/start.S b/cpu/mcf52x2/start.S index 686e2a53330..260a09abf76 100644 --- a/cpu/mcf52x2/start.S +++ b/cpu/mcf52x2/start.S @@ -58,7 +58,7 @@ _vectors: .long 0x00000000 /* Flash offset is 0 until we setup CS0 */ #if defined(CONFIG_R5200) .long 0x400 -#elif defined(CONFIG_M5282) +#elif defined(CONFIG_M5282) && (TEXT_BASE == CFG_INT_FLASH_BASE) .long _start - TEXT_BASE #else .long _START @@ -177,7 +177,11 @@ _after_flashbar_copy: * therefore no VBR to set */ #if !defined(CONFIG_MONITOR_IS_IN_RAM) +#if defined(CONFIG_M5282) && (TEXT_BASE == CFG_INT_FLASH_BASE) + move.l #CFG_INT_FLASH_BASE, %d0 +#else move.l #CFG_FLASH_BASE, %d0 +#endif movec %d0, %VBR #endif diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h index 3c17c1ea146..7bb9f60f765 100644 --- a/include/configs/M5282EVB.h +++ b/include/configs/M5282EVB.h @@ -163,7 +163,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ #define CFG_FLASH_BASE 0xffe00000 #define CFG_INT_FLASH_BASE 0xf0000000 #define CFG_INT_FLASH_ENABLE 0x21 -- cgit v1.3.1 From 95e9f2c212a65610b2e59a5c00d0113383a4da0b Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:10:23 -0500 Subject: ColdFire 5253: Assign correct SDRAM size Signed-off-by: TsiChungLiew --- include/configs/M5253EVBE.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'include') diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h index 48170e7a35a..f5e1b646ca2 100644 --- a/include/configs/M5253EVBE.h +++ b/include/configs/M5253EVBE.h @@ -146,7 +146,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x00000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */ #ifdef CONFIG_MONITOR_IS_IN_RAM #define CFG_MONITOR_BASE 0x20000 -- cgit v1.3.1 From c67e12e705b204cfe914e3e3e693d69a445dcabf Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:12:36 -0500 Subject: ColdFire 5329: Assign correct SDRAM size and fix cache Signed-off-by: TsiChungLiew --- cpu/mcf532x/start.S | 4 ++-- include/configs/M5329EVB.h | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'include') diff --git a/cpu/mcf532x/start.S b/cpu/mcf532x/start.S index 5cc1c87cdd0..61be2eac695 100644 --- a/cpu/mcf532x/start.S +++ b/cpu/mcf532x/start.S @@ -131,7 +131,7 @@ _start: movec %d0, %VBR move.l #(CFG_INIT_RAM_ADDR + CFG_INIT_RAM_CTRL), %d0 - movec %d0, %RAMBAR0 + movec %d0, %RAMBAR1 /* invalidate and disable cache */ move.l #0x01000000, %d0 /* Invalidate cache cmd */ @@ -268,7 +268,7 @@ _int_handler: icache_enable: move.l #0x01000000, %d0 /* Invalidate cache cmd */ movec %d0, %CACR /* Invalidate cache */ - move.l #(CFG_SDRAM_BASE + 0xc000 + ((CFG_SDRAM_SIZE & 0x1fe0) << 11)), %d0 + move.l #(CFG_SDRAM_BASE + 0x1c000), %d0 movec %d0, %ACR0 /* Enable cache */ move.l #0x80000200, %d0 /* Setup cache mask */ diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index d3b160505be..47d74a3c37a 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -175,7 +175,7 @@ * Please note that CFG_SDRAM_BASE _must_ start at 0 */ #define CFG_SDRAM_BASE 0x40000000 -#define CFG_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CFG_SDRAM_SIZE 32 /* SDRAM size in MB */ #define CFG_SDRAM_CFG1 0x53722730 #define CFG_SDRAM_CFG2 0x56670000 #define CFG_SDRAM_CTRL 0xE1092000 -- cgit v1.3.1 From e8ee8f3ade2a06c1893dd5e68f223070d650c7ed Mon Sep 17 00:00:00 2001 From: TsiChungLiew Date: Thu, 25 Oct 2007 17:16:22 -0500 Subject: ColdFire 54455: Fix correct boot location for atmel and intel Signed-off-by: TsiChungLiew --- Makefile | 4 ++++ board/freescale/m54455evb/config.mk | 4 +++- include/configs/M54455EVB.h | 36 ++++++++++++++++++++---------------- 3 files changed, 27 insertions(+), 17 deletions(-) (limited to 'include') diff --git a/Makefile b/Makefile index ce7b07f9d18..850c68e235c 100644 --- a/Makefile +++ b/Makefile @@ -1733,9 +1733,13 @@ M54455EVB_i66_config : unconfig >include/config.h ; \ if [ "$${FLASH}" == "INTEL" ] ; then \ echo "#undef CFG_ATMEL_BOOT" >> $(obj)include/config.h ; \ + echo "TEXT_BASE = 0x00000000" > $(obj)board/freescale/m54455evb/config.tmp ; \ + cp $(obj)board/freescale/m54455evb/u-boot.int $(obj)board/freescale/m54455evb/u-boot.lds ; \ echo "... with INTEL boot..." ; \ else \ echo "#define CFG_ATMEL_BOOT" >> $(obj)include/config.h ; \ + echo "TEXT_BASE = 0x04000000" > $(obj)board/freescale/m54455evb/config.tmp ; \ + cp $(obj)board/freescale/m54455evb/u-boot.atm $(obj)board/freescale/m54455evb/u-boot.lds ; \ echo "... with ATMEL boot..." ; \ fi; \ echo "#define CFG_INPUT_CLKSRC $${FREQ}" >> $(obj)include/config.h ; \ diff --git a/board/freescale/m54455evb/config.mk b/board/freescale/m54455evb/config.mk index ce014edca8f..b42fcc94ce7 100644 --- a/board/freescale/m54455evb/config.mk +++ b/board/freescale/m54455evb/config.mk @@ -22,4 +22,6 @@ # MA 02111-1307 USA # -TEXT_BASE = 0 +sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 6f4859c2380..ba050cb7e46 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -27,8 +27,8 @@ * board/config.h - configuration options, board specific */ -#ifndef _JAMICA54455_H -#define _JAMICA54455_H +#ifndef _M54455EVB_H +#define _M54455EVB_H /* * High Level Configuration Options @@ -75,7 +75,7 @@ #define CONFIG_CMD_MISC #define CONFIG_CMD_MII #define CONFIG_CMD_NET -#define CONFIG_CMD_PCI +#undef CONFIG_CMD_PCI #define CONFIG_CMD_PING #define CONFIG_CMD_REGINFO @@ -129,8 +129,8 @@ "u-boot=u-boot.bin\0" \ "load=tftp ${loadaddr) ${u-boot}\0" \ "upd=run load; run prog\0" \ - "prog=prot off 0 2ffff;" \ - "era 0 2ffff;" \ + "prog=prot off 4000000 402ffff;" \ + "era 4000000 402ffff;" \ "cp.b ${loadaddr} 0 ${filesize};" \ "save\0" \ "" @@ -174,6 +174,7 @@ #define CFG_IMMR CFG_MBAR /* PCI */ +#ifdef CONFIG_CMD_PCI #define CONFIG_PCI 1 #define CFG_PCI_MEM_BUS 0xA0000000 @@ -187,6 +188,7 @@ #define CFG_PCI_CFG_BUS 0xB0000000 #define CFG_PCI_CFG_PHYS CFG_PCI_CFG_BUS #define CFG_PCI_CFG_SIZE 0x01000000 +#endif /* FPGA - Spartan 2 */ /* experiment @@ -268,8 +270,6 @@ /* Configuration for environment * Environment is embedded in u-boot in the second sector of the flash */ -#define CFG_ENV_OFFSET 0x4000 -#define CFG_ENV_SECT_SIZE 0x2000 #define CFG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_OVERWRITE 1 #undef CFG_ENV_IS_EMBEDDED @@ -278,13 +278,17 @@ * FLASH organization */ #ifdef CFG_ATMEL_BOOT -# define CFG_FLASH_BASE 0 +# define CFG_FLASH_BASE CFG_CS0_BASE # define CFG_FLASH0_BASE CFG_CS0_BASE # define CFG_FLASH1_BASE CFG_CS1_BASE +# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x4000) +# define CFG_ENV_SECT_SIZE 0x2000 #else # define CFG_FLASH_BASE CFG_FLASH0_BASE # define CFG_FLASH0_BASE CFG_CS1_BASE # define CFG_FLASH1_BASE CFG_CS0_BASE +# define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000) +# define CFG_ENV_SECT_SIZE 0x20000 #endif /* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system @@ -328,9 +332,9 @@ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. */ #ifdef CFG_ATMEL_BOOT -# define CONFIG_JFFS2_DEV "nor0" +# define CONFIG_JFFS2_DEV "nor1" # define CONFIG_JFFS2_PART_SIZE 0x01000000 -# define CONFIG_JFFS2_PART_OFFSET CFG_FLASH1_BASE +# define CONFIG_JFFS2_PART_OFFSET (CFG_FLASH1_BASE + 0x500000) #else # define CONFIG_JFFS2_DEV "nor0" # define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000) @@ -356,20 +360,20 @@ #ifdef CFG_ATMEL_BOOT /* Atmel Flash */ -#define CFG_CS0_BASE 0 +#define CFG_CS0_BASE 0x04000000 #define CFG_CS0_MASK 0x00070001 #define CFG_CS0_CTRL 0x00001140 /* Intel Flash */ -#define CFG_CS1_BASE 0x04000000 +#define CFG_CS1_BASE 0x00000000 #define CFG_CS1_MASK 0x01FF0001 -#define CFG_CS1_CTRL 0x003F3D60 +#define CFG_CS1_CTRL 0x00000D60 #define CFG_ATMEL_BASE CFG_CS0_BASE #else /* Intel Flash */ -#define CFG_CS0_BASE 0 +#define CFG_CS0_BASE 0x00000000 #define CFG_CS0_MASK 0x01FF0001 -#define CFG_CS0_CTRL 0x003F3D60 +#define CFG_CS0_CTRL 0x00000D60 /* Atmel Flash */ #define CFG_CS1_BASE 0x04000000 #define CFG_CS1_MASK 0x00070001 @@ -388,4 +392,4 @@ #define CFG_CS3_MASK 0x00070001 #define CFG_CS3_CTRL 0x00000020 -#endif /* _JAMICA54455_H */ +#endif /* _M54455EVB_H */ -- cgit v1.3.1 From 8b6684a698500be9c142ec2c9f46cfc348e17f0c Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Wed, 24 Oct 2007 15:48:37 +0200 Subject: ATSTK1002: Remove default ethernet addresses Wolfgang is right: It's not a good idea to set up default initial ethernet addresses for a board, even though they belong to the local range. This will change the failure mode from "IT manager screams at you for using duplicate ethernet addresses" to a nice error message explaining that the ethernet address hasn't been set properly. Signed-off-by: Haavard Skinnemoen --- include/configs/atstk1002.h | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-) (limited to 'include') diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h index 1809fc5d864..b33e26fe011 100644 --- a/include/configs/atstk1002.h +++ b/include/configs/atstk1002.h @@ -114,15 +114,10 @@ #define CONFIG_AUTOBOOT_STOP_STR " " /* - * These are "locally administered ethernet addresses" generated by - * ./tools/gen_eth_addr - * - * After booting the board for the first time, new addresses should be - * generated and assigned to the environment variables "ethaddr" and - * "eth1addr". + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr" and "eth1addr". This is normally done during production. */ -#define CONFIG_ETHADDR 6a:87:71:14:cd:cb -#define CONFIG_ETH1ADDR ca:f8:15:e6:3e:e6 #define CONFIG_OVERWRITE_ETHADDR_ONCE 1 #define CONFIG_NET_MULTI 1 -- cgit v1.3.1