From 8f8bd565f35ff8a068727bfcf8975c50df082043 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:38 -0500 Subject: USB Consolidate descriptor definitions The header files usb.h and usbdescriptors.h have the same nameed structure definitions for usb_config_descriptor usb_interface_descriptor usb_endpoint_descriptor usb_device_descriptor usb_string_descriptor These are out right duplicates in usb.h usb_device_descriptor usb_string_descriptor This one has extra unused elements usb_endpoint_descriptor unsigned char bRefresh unsigned char bSynchAddress; These in usb.h have extra elements at the end of the usb 2.0 specified descriptor and are used. usb_config_descriptor usb_interface_descriptor The change is to consolidate the definition of the descriptors to usbdescriptors.h. The dublicates in usb.h are removed. The extra element structure will have their name shorted by removing the '_descriptor' suffix. So usb_config_descriptor -> usb_config usb_interface_descriptor -> usb_interface For these, the common descriptor elements are accessed now by an element 'desc'. As an example - if (iface->bInterfaceClass != USB_CLASS_HUB) + if (iface->desc.bInterfaceClass != USB_CLASS_HUB) This has been compile tested on MAKEALL arm, ppc and mips. Signed-off-by: Tom Rix --- include/usb.h | 70 ++++++++--------------------------------------------------- 1 file changed, 9 insertions(+), 61 deletions(-) (limited to 'include') diff --git a/include/usb.h b/include/usb.h index 7c47098d8a4..4148d67e121 100644 --- a/include/usb.h +++ b/include/usb.h @@ -27,6 +27,7 @@ #define _USB_H_ #include +#include /* Everything is aribtrary */ #define USB_ALTSETTINGALLOC 4 @@ -41,13 +42,6 @@ #define USB_CNTL_TIMEOUT 100 /* 100ms timeout */ -/* String descriptor */ -struct usb_string_descriptor { - unsigned char bLength; - unsigned char bDescriptorType; - unsigned short wData[1]; -} __attribute__ ((packed)); - /* device request (setup) */ struct devrequest { unsigned char requesttype; @@ -63,47 +57,9 @@ struct usb_descriptor_header { unsigned char bDescriptorType; } __attribute__ ((packed)); -/* Device descriptor */ -struct usb_device_descriptor { - unsigned char bLength; - unsigned char bDescriptorType; - unsigned short bcdUSB; - unsigned char bDeviceClass; - unsigned char bDeviceSubClass; - unsigned char bDeviceProtocol; - unsigned char bMaxPacketSize0; - unsigned short idVendor; - unsigned short idProduct; - unsigned short bcdDevice; - unsigned char iManufacturer; - unsigned char iProduct; - unsigned char iSerialNumber; - unsigned char bNumConfigurations; -} __attribute__ ((packed)); - -/* Endpoint descriptor */ -struct usb_endpoint_descriptor { - unsigned char bLength; - unsigned char bDescriptorType; - unsigned char bEndpointAddress; - unsigned char bmAttributes; - unsigned short wMaxPacketSize; - unsigned char bInterval; - unsigned char bRefresh; - unsigned char bSynchAddress; -} __attribute__ ((packed)) __attribute__ ((aligned(2))); - -/* Interface descriptor */ -struct usb_interface_descriptor { - unsigned char bLength; - unsigned char bDescriptorType; - unsigned char bInterfaceNumber; - unsigned char bAlternateSetting; - unsigned char bNumEndpoints; - unsigned char bInterfaceClass; - unsigned char bInterfaceSubClass; - unsigned char bInterfaceProtocol; - unsigned char iInterface; +/* Interface */ +struct usb_interface { + struct usb_interface_descriptor desc; unsigned char no_of_ep; unsigned char num_altsetting; @@ -112,20 +68,12 @@ struct usb_interface_descriptor { struct usb_endpoint_descriptor ep_desc[USB_MAXENDPOINTS]; } __attribute__ ((packed)); - -/* Configuration descriptor information.. */ -struct usb_config_descriptor { - unsigned char bLength; - unsigned char bDescriptorType; - unsigned short wTotalLength; - unsigned char bNumInterfaces; - unsigned char bConfigurationValue; - unsigned char iConfiguration; - unsigned char bmAttributes; - unsigned char MaxPower; +/* Configuration information.. */ +struct usb_config { + struct usb_configuration_descriptor desc; unsigned char no_of_if; /* number of interfaces */ - struct usb_interface_descriptor if_desc[USB_MAXINTERFACES]; + struct usb_interface if_desc[USB_MAXINTERFACES]; } __attribute__ ((packed)); enum { @@ -156,7 +104,7 @@ struct usb_device { int configno; /* selected config number */ struct usb_device_descriptor descriptor; /* Device Descriptor */ - struct usb_config_descriptor config; /* config descriptor */ + struct usb_config config; /* config descriptor */ int have_langid; /* whether string_langid is valid yet */ int string_langid; /* language ID for strings */ -- cgit v1.2.3 From 988365a2048356f94ed0c294009233317c9fb4b2 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:39 -0500 Subject: USB add macros for debugging usb device setup. When developing usb device features, it is useful to print out common usb structures. Signed-off-by: Tom Rix --- include/usbdescriptors.h | 26 ++++++++++++ include/usbdevice.h | 103 +++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 129 insertions(+) (limited to 'include') diff --git a/include/usbdescriptors.h b/include/usbdescriptors.h index a752097e5bc..2dec3b93d65 100644 --- a/include/usbdescriptors.h +++ b/include/usbdescriptors.h @@ -504,4 +504,30 @@ struct usb_class_descriptor { } __attribute__ ((packed)); +#ifdef DEBUG +static inline void print_device_descriptor(struct usb_device_descriptor *d) +{ + serial_printf("usb device descriptor \n"); + serial_printf("\tbLength %2.2x\n", d->bLength); + serial_printf("\tbDescriptorType %2.2x\n", d->bDescriptorType); + serial_printf("\tbcdUSB %4.4x\n", d->bcdUSB); + serial_printf("\tbDeviceClass %2.2x\n", d->bDeviceClass); + serial_printf("\tbDeviceSubClass %2.2x\n", d->bDeviceSubClass); + serial_printf("\tbDeviceProtocol %2.2x\n", d->bDeviceProtocol); + serial_printf("\tbMaxPacketSize0 %2.2x\n", d->bMaxPacketSize0); + serial_printf("\tidVendor %4.4x\n", d->idVendor); + serial_printf("\tidProduct %4.4x\n", d->idProduct); + serial_printf("\tbcdDevice %4.4x\n", d->bcdDevice); + serial_printf("\tiManufacturer %2.2x\n", d->iManufacturer); + serial_printf("\tiProduct %2.2x\n", d->iProduct); + serial_printf("\tiSerialNumber %2.2x\n", d->iSerialNumber); + serial_printf("\tbNumConfigurations %2.2x\n", d->bNumConfigurations); +} + +#else + +/* stubs */ +#define print_device_descriptor(d) + +#endif /* DEBUG */ #endif diff --git a/include/usbdevice.h b/include/usbdevice.h index 206dbbc864e..41716364b31 100644 --- a/include/usbdevice.h +++ b/include/usbdevice.h @@ -663,4 +663,107 @@ int usbd_endpoint_halted (struct usb_device_instance *device, int endpoint); void usbd_rcv_complete(struct usb_endpoint_instance *endpoint, int len, int urb_bad); void usbd_tx_complete (struct usb_endpoint_instance *endpoint); +/* These are macros used in debugging */ +#ifdef DEBUG +static inline void print_urb(struct urb *u) +{ + serial_printf("urb %p\n", (u)); + serial_printf("\tendpoint %p\n", u->endpoint); + serial_printf("\tdevice %p\n", u->device); + serial_printf("\tbuffer %p\n", u->buffer); + serial_printf("\tbuffer_length %d\n", u->buffer_length); + serial_printf("\tactual_length %d\n", u->actual_length); + serial_printf("\tstatus %d\n", u->status); + serial_printf("\tdata %d\n", u->data); +} + +static inline void print_usb_device_request(struct usb_device_request *r) +{ + serial_printf("usb request\n"); + serial_printf("\tbmRequestType 0x%2.2x\n", r->bmRequestType); + if ((r->bmRequestType & USB_REQ_DIRECTION_MASK) == 0) + serial_printf("\t\tDirection : To device\n"); + else + serial_printf("\t\tDirection : To host\n"); + if ((r->bmRequestType & USB_TYPE_STANDARD) == USB_TYPE_STANDARD) + serial_printf("\t\tType : Standard\n"); + if ((r->bmRequestType & USB_TYPE_CLASS) == USB_TYPE_CLASS) + serial_printf("\t\tType : Standard\n"); + if ((r->bmRequestType & USB_TYPE_VENDOR) == USB_TYPE_VENDOR) + serial_printf("\t\tType : Standard\n"); + if ((r->bmRequestType & USB_TYPE_RESERVED) == USB_TYPE_RESERVED) + serial_printf("\t\tType : Standard\n"); + if ((r->bmRequestType & USB_REQ_RECIPIENT_MASK) == + USB_REQ_RECIPIENT_DEVICE) + serial_printf("\t\tRecipient : Device\n"); + if ((r->bmRequestType & USB_REQ_RECIPIENT_MASK) == + USB_REQ_RECIPIENT_INTERFACE) + serial_printf("\t\tRecipient : Interface\n"); + if ((r->bmRequestType & USB_REQ_RECIPIENT_MASK) == + USB_REQ_RECIPIENT_ENDPOINT) + serial_printf("\t\tRecipient : Endpoint\n"); + if ((r->bmRequestType & USB_REQ_RECIPIENT_MASK) == + USB_REQ_RECIPIENT_OTHER) + serial_printf("\t\tRecipient : Other\n"); + serial_printf("\tbRequest 0x%2.2x\n", r->bRequest); + if (r->bRequest == USB_REQ_GET_STATUS) + serial_printf("\t\tGET_STATUS\n"); + else if (r->bRequest == USB_REQ_SET_ADDRESS) + serial_printf("\t\tSET_ADDRESS\n"); + else if (r->bRequest == USB_REQ_SET_FEATURE) + serial_printf("\t\tSET_FEATURE\n"); + else if (r->bRequest == USB_REQ_GET_DESCRIPTOR) + serial_printf("\t\tGET_DESCRIPTOR\n"); + else if (r->bRequest == USB_REQ_SET_CONFIGURATION) + serial_printf("\t\tSET_CONFIGURATION\n"); + else if (r->bRequest == USB_REQ_SET_INTERFACE) + serial_printf("\t\tUSB_REQ_SET_INTERFACE\n"); + else + serial_printf("\tUNKNOWN %d\n", r->bRequest); + serial_printf("\twValue 0x%4.4x\n", r->wValue); + if (r->bRequest == USB_REQ_GET_DESCRIPTOR) { + switch (r->wValue >> 8) { + case USB_DESCRIPTOR_TYPE_DEVICE: + serial_printf("\tDEVICE\n"); + break; + case USB_DESCRIPTOR_TYPE_CONFIGURATION: + serial_printf("\tCONFIGURATION\n"); + break; + case USB_DESCRIPTOR_TYPE_STRING: + serial_printf("\tSTRING\n"); + break; + case USB_DESCRIPTOR_TYPE_INTERFACE: + serial_printf("\tINTERFACE\n"); + break; + case USB_DESCRIPTOR_TYPE_ENDPOINT: + serial_printf("\tENDPOINT\n"); + break; + case USB_DESCRIPTOR_TYPE_DEVICE_QUALIFIER: + serial_printf("\tDEVICE_QUALIFIER\n"); + break; + case USB_DESCRIPTOR_TYPE_OTHER_SPEED_CONFIGURATION: + serial_printf("\tOTHER_SPEED_CONFIGURATION\n"); + break; + case USB_DESCRIPTOR_TYPE_INTERFACE_POWER: + serial_printf("\tINTERFACE_POWER\n"); + break; + case USB_DESCRIPTOR_TYPE_HID: + serial_printf("\tHID\n"); + break; + case USB_DESCRIPTOR_TYPE_REPORT: + serial_printf("\tREPORT\n"); + break; + default: + serial_printf("\tUNKNOWN TYPE\n"); + break; + } + } + serial_printf("\twIndex 0x%4.4x\n", r->wIndex); + serial_printf("\twLength 0x%4.4x\n", r->wLength); +} +#else +/* stubs */ +#define print_urb(u) +#define print_usb_device_request(r) +#endif /* DEBUG */ #endif -- cgit v1.2.3 From bffbb2a86d2a3aa28bd8f9869aa553082fb5af5f Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:40 -0500 Subject: TWL4030 Add usb PHY support The twl4030 provides a PHY device for connecting a link device, like musb, to physical connection. This change adds the twl4030 usb registers and functions for initializing the PHY as required by omap3. Signed-off-by: Tom Rix --- include/twl4030.h | 143 ++++++++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 128 insertions(+), 15 deletions(-) (limited to 'include') diff --git a/include/twl4030.h b/include/twl4030.h index f260ecb8b12..feaec47b36a 100644 --- a/include/twl4030.h +++ b/include/twl4030.h @@ -342,21 +342,129 @@ #define TWL4030_KEYPAD_CTRL_SOFT_NRST (1 << 0) /* USB */ -#define TWL4030_USB_FUNC_CTRL (0x04) -#define TWL4030_USB_OPMODE_MASK (3 << 3) -#define TWL4030_USB_XCVRSELECT_MASK (3 << 0) -#define TWL4030_USB_IFC_CTRL (0x07) -#define TWL4030_USB_CARKITMODE (1 << 2) -#define TWL4030_USB_POWER_CTRL (0xAC) -#define TWL4030_USB_OTG_ENAB (1 << 5) -#define TWL4030_USB_PHY_PWR_CTRL (0xFD) -#define TWL4030_USB_PHYPWD (1 << 0) -#define TWL4030_USB_PHY_CLK_CTRL (0xFE) -#define TWL4030_USB_CLOCKGATING_EN (1 << 2) -#define TWL4030_USB_CLK32K_EN (1 << 1) -#define TWL4030_USB_REQ_PHY_DPLL_CLK (1 << 0) -#define TWL4030_USB_PHY_CLK_CTRL_STS (0xFF) -#define TWL4030_USB_PHY_DPLL_CLK (1 << 0) +#define TWL4030_USB_VENDOR_ID_LO 0x00 +#define TWL4030_USB_VENDOR_ID_HI 0x01 +#define TWL4030_USB_PRODUCT_ID_LO 0x02 +#define TWL4030_USB_PRODUCT_ID_HI 0x03 +#define TWL4030_USB_FUNC_CTRL 0x04 +#define TWL4030_USB_FUNC_CTRL_SET 0x05 +#define TWL4030_USB_FUNC_CTRL_CLR 0x06 +#define TWL4030_USB_IFC_CTRL 0x07 +#define TWL4030_USB_IFC_CTRL_SET 0x08 +#define TWL4030_USB_IFC_CTRL_CLR 0x09 +#define TWL4030_USB_OTG_CTRL 0x0A +#define TWL4030_USB_OTG_CTRL_SET 0x0B +#define TWL4030_USB_OTG_CTRL_CLR 0x0C +#define TWL4030_USB_USB_INT_EN_RISE 0x0D +#define TWL4030_USB_USB_INT_EN_RISE_SET 0x0E +#define TWL4030_USB_USB_INT_EN_RISE_CLR 0x0F +#define TWL4030_USB_USB_INT_EN_FALL 0x10 +#define TWL4030_USB_USB_INT_EN_FALL_SET 0x11 +#define TWL4030_USB_USB_INT_EN_FALL_CLR 0x12 +#define TWL4030_USB_USB_INT_STS 0x13 +#define TWL4030_USB_USB_INT_LATCH 0x14 +#define TWL4030_USB_DEBUG 0x15 +#define TWL4030_USB_SCRATCH_REG 0x16 +#define TWL4030_USB_SCRATCH_REG_SET 0x17 +#define TWL4030_USB_SCRATCH_REG_CLR 0x18 +#define TWL4030_USB_CARKIT_CTRL 0x19 +#define TWL4030_USB_CARKIT_CTRL_SET 0x1A +#define TWL4030_USB_CARKIT_CTRL_CLR 0x1B +#define TWL4030_USB_CARKIT_INT_DELAY 0x1C +#define TWL4030_USB_CARKIT_INT_EN 0x1D +#define TWL4030_USB_CARKIT_INT_EN_SET 0x1E +#define TWL4030_USB_CARKIT_INT_EN_CLR 0x1F +#define TWL4030_USB_CARKIT_INT_STS 0x20 +#define TWL4030_USB_CARKIT_INT_LATCH 0x21 +#define TWL4030_USB_CARKIT_PLS_CTRL 0x22 +#define TWL4030_USB_CARKIT_PLS_CTRL_SET 0x23 +#define TWL4030_USB_CARKIT_PLS_CTRL_CLR 0x24 +#define TWL4030_USB_TRANS_POS_WIDTH 0x25 +#define TWL4030_USB_TRANS_NEG_WIDTH 0x26 +#define TWL4030_USB_RCV_PLTY_RECOVERY 0x27 +#define TWL4030_USB_MCPC_CTRL 0x30 +#define TWL4030_USB_MCPC_CTRL_SET 0x31 +#define TWL4030_USB_MCPC_CTRL_CLR 0x32 +#define TWL4030_USB_MCPC_IO_CTRL 0x33 +#define TWL4030_USB_MCPC_IO_CTRL_SET 0x34 +#define TWL4030_USB_MCPC_IO_CTRL_CLR 0x35 +#define TWL4030_USB_MCPC_CTRL2 0x36 +#define TWL4030_USB_MCPC_CTRL2_SET 0x37 +#define TWL4030_USB_MCPC_CTRL2_CLR 0x38 +#define TWL4030_USB_OTHER_FUNC_CTRL 0x80 +#define TWL4030_USB_OTHER_FUNC_CTRL_SET 0x81 +#define TWL4030_USB_OTHER_FUNC_CTRL_CLR 0x82 +#define TWL4030_USB_OTHER_IFC_CTRL 0x83 +#define TWL4030_USB_OTHER_IFC_CTRL_SET 0x84 +#define TWL4030_USB_OTHER_IFC_CTRL_CLR 0x85 +#define TWL4030_USB_OTHER_INT_EN_RISE_SET 0x87 +#define TWL4030_USB_OTHER_INT_EN_RISE_CLR 0x88 +#define TWL4030_USB_OTHER_INT_EN_FALL 0x89 +#define TWL4030_USB_OTHER_INT_EN_FALL_SET 0x8A +#define TWL4030_USB_OTHER_INT_EN_FALL_CLR 0x8B +#define TWL4030_USB_OTHER_INT_STS 0x8C +#define TWL4030_USB_OTHER_INT_LATCH 0x8D +#define TWL4030_USB_ID_STATUS 0x96 +#define TWL4030_USB_CARKIT_SM_1_INT_EN 0x97 +#define TWL4030_USB_CARKIT_SM_1_INT_EN_SET 0x98 +#define TWL4030_USB_CARKIT_SM_1_INT_EN_CLR 0x99 +#define TWL4030_USB_CARKIT_SM_1_INT_STS 0x9A +#define TWL4030_USB_CARKIT_SM_1_INT_LATCH 0x9B +#define TWL4030_USB_CARKIT_SM_2_INT_EN 0x9C +#define TWL4030_USB_CARKIT_SM_2_INT_EN_SET 0x9D +#define TWL4030_USB_CARKIT_SM_2_INT_EN_CLR 0x9E +#define TWL4030_USB_CARKIT_SM_2_INT_STS 0x9F +#define TWL4030_USB_CARKIT_SM_2_INT_LATCH 0xA0 +#define TWL4030_USB_CARKIT_SM_CTRL 0xA1 +#define TWL4030_USB_CARKIT_SM_CTRL_SET 0xA2 +#define TWL4030_USB_CARKIT_SM_CTRL_CLR 0xA3 +#define TWL4030_USB_CARKIT_SM_CMD 0xA4 +#define TWL4030_USB_CARKIT_SM_CMD_SET 0xA5 +#define TWL4030_USB_CARKIT_SM_CMD_CLR 0xA6 +#define TWL4030_USB_CARKIT_SM_CMD_STS 0xA7 +#define TWL4030_USB_CARKIT_SM_STATUS 0xA8 +#define TWL4030_USB_CARKIT_SM_ERR_STATUS 0xAA +#define TWL4030_USB_CARKIT_SM_CTRL_STATE 0xAB +#define TWL4030_USB_POWER_CTRL 0xAC +#define TWL4030_USB_POWER_CTRL_SET 0xAD +#define TWL4030_USB_POWER_CTRL_CLR 0xAE +#define TWL4030_USB_OTHER_IFC_CTRL2 0xAF +#define TWL4030_USB_OTHER_IFC_CTRL2_SET 0xB0 +#define TWL4030_USB_OTHER_IFC_CTRL2_CLR 0xB1 +#define TWL4030_USB_REG_CTRL_EN 0xB2 +#define TWL4030_USB_REG_CTRL_EN_SET 0xB3 +#define TWL4030_USB_REG_CTRL_EN_CLR 0xB4 +#define TWL4030_USB_REG_CTRL_ERROR 0xB5 +#define TWL4030_USB_OTHER_FUNC_CTRL2 0xB8 +#define TWL4030_USB_OTHER_FUNC_CTRL2_SET 0xB9 +#define TWL4030_USB_OTHER_FUNC_CTRL2_CLR 0xBA +#define TWL4030_USB_CARKIT_ANA_CTRL 0xBB +#define TWL4030_USB_CARKIT_ANA_CTRL_SET 0xBC +#define TWL4030_USB_CARKIT_ANA_CTRL_CLR 0xBD +#define TWL4030_USB_VBUS_DEBOUNCE 0xC0 +#define TWL4030_USB_ID_DEBOUNCE 0xC1 +#define TWL4030_USB_TPH_DP_CON_MIN 0xC2 +#define TWL4030_USB_TPH_DP_CON_MAX 0xC3 +#define TWL4030_USB_TCR_DP_CON_MIN 0xC4 +#define TWL4030_USB_TCR_DP_CON_MAX 0xC5 +#define TWL4030_USB_TPH_DP_PD_SHORT 0xC6 +#define TWL4030_USB_TPH_CMD_DLY 0xC7 +#define TWL4030_USB_TPH_DET_RST 0xC8 +#define TWL4030_USB_TPH_AUD_BIAS 0xC9 +#define TWL4030_USB_TCR_UART_DET_MIN 0xCA +#define TWL4030_USB_TCR_UART_DET_MAX 0xCB +#define TWL4030_USB_TPH_ID_INT_PW 0xCD +#define TWL4030_USB_TACC_ID_INT_WAIT 0xCE +#define TWL4030_USB_TACC_ID_INT_PW 0xCF +#define TWL4030_USB_TPH_CMD_WAIT 0xD0 +#define TWL4030_USB_TPH_ACK_WAIT 0xD1 +#define TWL4030_USB_TPH_DP_DISC_DET 0xD2 +#define TWL4030_USB_VBAT_TIMER 0xD3 +#define TWL4030_USB_CARKIT_4W_DEBUG 0xE0 +#define TWL4030_USB_CARKIT_5W_DEBUG 0xE1 +#define TWL4030_USB_PHY_PWR_CTRL 0xFD +#define TWL4030_USB_PHY_CLK_CTRL 0xFE +#define TWL4030_USB_PHY_CLK_CTRL_STS 0xFF /* * Convience functions to read and write from TWL4030 @@ -398,4 +506,9 @@ void twl4030_power_mmc_init(void); */ void twl4030_led_init(void); +/* + * USB + */ +int twl4030_usb_ulpi_init(void); + #endif /* TWL4030_H */ -- cgit v1.2.3 From f298e4b6dd56df3e35a13a6ddd572ca3baf06ad2 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:41 -0500 Subject: OMAP3 Add usb device support This change adds the usb device support for musb. Omap3 platform support added at the same level as davinci. The interface for usbtty to use the musb device support was added. Verified on omap3 beagle, zoom1 and zoom2. Signed-off-by: Tom Rix --- include/usb.h | 3 ++- include/usb/musb_udc.h | 54 ++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 56 insertions(+), 1 deletion(-) create mode 100644 include/usb/musb_udc.h (limited to 'include') diff --git a/include/usb.h b/include/usb.h index 4148d67e121..1cc3e4229da 100644 --- a/include/usb.h +++ b/include/usb.h @@ -131,7 +131,8 @@ struct usb_device { #if defined(CONFIG_USB_UHCI) || defined(CONFIG_USB_OHCI) || \ defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ - defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) + defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ + defined(CONFIG_USB_OMAP3) int usb_lowlevel_init(void); int usb_lowlevel_stop(void); diff --git a/include/usb/musb_udc.h b/include/usb/musb_udc.h new file mode 100644 index 00000000000..ef37dbbcc4a --- /dev/null +++ b/include/usb/musb_udc.h @@ -0,0 +1,54 @@ +/* + * Copyright (c) 2009 Wind River Systems, Inc. + * Tom Rix + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __MUSB_UDC_H__ +#define __MUSB_UDC_H__ + +#include + +/* UDC level routines */ +void udc_irq(void); +void udc_set_nak(int ep_num); +void udc_unset_nak(int ep_num); +int udc_endpoint_write(struct usb_endpoint_instance *endpoint); +void udc_setup_ep(struct usb_device_instance *device, unsigned int id, + struct usb_endpoint_instance *endpoint); +void udc_connect(void); +void udc_disconnect(void); +void udc_enable(struct usb_device_instance *device); +void udc_disable(void); +void udc_startup_events(struct usb_device_instance *device); +int udc_init(void); + +/* usbtty */ +#ifdef CONFIG_USB_TTY + +#define EP0_MAX_PACKET_SIZE 64 /* MUSB_EP0_FIFOSIZE */ +#define UDC_INT_ENDPOINT 1 +#define UDC_INT_PACKET_SIZE 64 +#define UDC_OUT_ENDPOINT 2 +#define UDC_OUT_PACKET_SIZE 64 +#define UDC_IN_ENDPOINT 3 +#define UDC_IN_PACKET_SIZE 64 +#define UDC_BULK_PACKET_SIZE 64 + +#endif /* CONFIG_USB_TTY */ + +#endif /* __MUSB_UDC_H__ */ + -- cgit v1.2.3 From 05be5a60e98eb1243901f556fefd66b1691fabe4 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:42 -0500 Subject: OMAP3 zoom1 Add usbtty configuration The primary console of zoom1 is the serial out from the jumpers accessed by removing the back panel. A secondary console is to use the usbtty. The user can set this manually by doing setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty saveenv usbtty will be usable by accessing the /dev/ttyACM0 on a linux host. Signed-off-by: Tom Rix --- include/configs/omap3_zoom1.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'include') diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h index ef7a28bbc5a..fa58281593c 100644 --- a/include/configs/omap3_zoom1.h +++ b/include/configs/omap3_zoom1.h @@ -101,6 +101,21 @@ /* DDR - I use Micron DDR */ #define CONFIG_OMAP3_MICRON_DDR 1 +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Zoom1" + /* commands to include */ #include @@ -160,6 +175,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "videomode=1024x768@60,vxres=1024,vyres=768\0" \ "videospec=omapfb:vram:2M,vram:4M\0" \ -- cgit v1.2.3 From 25374bfbf3a6c6624d8db512c95a4960e3a84635 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:43 -0500 Subject: OMAP3 beagle Add usbtty configuration The primary console of beagle is the serial header. A secondary console is to use the usbtty. The user can set this manually by doing setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty saveenv usbtty will be usable by accessing the /dev/ttyACM0 on a linux host. Signed-off-by: Tom Rix --- include/configs/omap3_beagle.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'include') diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index a6fe5e12bd6..4fe3bd8bee6 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -100,6 +100,21 @@ /* DDR - I use Micron DDR */ #define CONFIG_OMAP3_MICRON_DDR 1 +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Beagle" + /* commands to include */ #include @@ -164,6 +179,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ -- cgit v1.2.3 From 6299487ef5dcdb06e0394f5955755c8dd9ce707b Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:44 -0500 Subject: USBTTY make some function declarations easier to use. Zoom2 needs to use these declarations and the include directory is a better place from them than in the middle of the driver directory. It did not make sense to create a new file for just a couple of lines so they were appended to the serial.h Signed-off-by: Tom Rix --- include/serial.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'include') diff --git a/include/serial.h b/include/serial.h index bbda3f08c60..43451a30195 100644 --- a/include/serial.h +++ b/include/serial.h @@ -66,4 +66,10 @@ extern void serial_stdio_init(void); extern int serial_assign(char * name); extern void serial_reinit_all(void); +/* For usbtty */ +extern int usbtty_getc(void); +extern void usbtty_putc(const char c); +extern void usbtty_puts(const char *str); +extern int usbtty_tstc(void); + #endif -- cgit v1.2.3 From 2ec1abea4359b94523d45a20d68d8582e09ace46 Mon Sep 17 00:00:00 2001 From: Tom Rix Date: Sat, 31 Oct 2009 12:37:45 -0500 Subject: OMAP3 zoom2 Use usbtty if the debug board is not connected. The preferred serial output comes from the debug board. When the debug board is disconnected, fall back on using usbtty from the usb connector on the Zoom2 board. This shows up as /dev/ttyACM0 in a linux host. Signed-off-by: Tom Rix --- include/configs/omap3_zoom2.h | 17 +++++++++++++++++ include/serial.h | 12 ++++++++++++ 2 files changed, 29 insertions(+) (limited to 'include') diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h index 2b076666e96..7a8beb8505d 100644 --- a/include/configs/omap3_zoom2.h +++ b/include/configs/omap3_zoom2.h @@ -125,6 +125,20 @@ #define CONFIG_OMAP3_GPIO_3 /* board revision */ #define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */ +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "Zoom2" + /* commands to include */ #include @@ -170,6 +184,9 @@ /* Environment information */ #define CONFIG_BOOTDELAY 10 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbtty=cdc_acm\0" \ + /* * Miscellaneous configurable options */ diff --git a/include/serial.h b/include/serial.h index 43451a30195..f2638ec5667 100644 --- a/include/serial.h +++ b/include/serial.h @@ -67,9 +67,21 @@ extern int serial_assign(char * name); extern void serial_reinit_all(void); /* For usbtty */ +#ifdef CONFIG_USB_TTY + extern int usbtty_getc(void); extern void usbtty_putc(const char c); extern void usbtty_puts(const char *str); extern int usbtty_tstc(void); +#else + +/* stubs */ +#define usbtty_getc() 0 +#define usbtty_putc(a) +#define usbtty_puts(a) +#define usbtty_tstc() 0 + +#endif /* CONFIG_USB_TTY */ + #endif -- cgit v1.2.3 From 73c8640e93881439b87a5734485a9e56a494ef50 Mon Sep 17 00:00:00 2001 From: Ajay Kumar Gupta Date: Wed, 4 Nov 2009 15:58:23 -0600 Subject: omap3evm: musb: add USB config Added USB host and device config for host (MSC, Keyboard) and device (ACM) functionalities. Signed-off-by: Ajay Kumar Gupta --- include/configs/omap3_evm.h | 39 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 39 insertions(+) (limited to 'include') diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 00093f83dc0..630b00faed4 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -104,6 +104,44 @@ /* DDR - I use Micron DDR */ #define CONFIG_OMAP3_MICRON_DDR 1 +/* USB + * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard + * Enable CONFIG_MUSB_UDD for Device functionalities. + */ +#define CONFIG_USB_OMAP3 1 +#define CONFIG_MUSB_HCD 1 +/* #define CONFIG_MUSB_UDC 1 */ + +#ifdef CONFIG_USB_OMAP3 + +#ifdef CONFIG_MUSB_HCD +#define CONFIG_CMD_USB + +#define CONFIG_USB_STORAGE +#define CONGIG_CMD_STORAGE +#define CONFIG_CMD_FAT + +#ifdef CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_MUSB_HCD */ + +#ifdef CONFIG_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "EVM" +#endif /* CONFIG_MUSB_UDC */ + +#endif /* CONFIG_USB_OMAP3 */ + /* commands to include */ #include @@ -160,6 +198,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ + "usbtty=cdc_acm\0" \ "console=ttyS2,115200n8\0" \ "mmcargs=setenv bootargs console=${console} " \ "root=/dev/mmcblk0p2 rw " \ -- cgit v1.2.3