// SPDX-License-Identifier: BSD-3-Clause /* * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. */ /dts-v1/; #include #include #include "talos.dtsi" #include "pm8150.dtsi" / { aliases { i2c1 = &i2c1; i2c5 = &i2c5; mmc0 = &sdhc_1; serial0 = &uart0; serial1 = &uart7; spi6 = &spi6; }; chosen { stdout-path = "serial0:115200n8"; }; clocks { can_osc: can-oscillator { compatible = "fixed-clock"; clock-frequency = <20000000>; #clock-cells = <0>; }; sleep_clk: sleep-clk { compatible = "fixed-clock"; clock-frequency = <32764>; #clock-cells = <0>; }; xo_board_clk: xo-board-clk { compatible = "fixed-clock"; clock-frequency = <38400000>; #clock-cells = <0>; }; }; vreg_conn_1p8: regulator-conn-1p8 { compatible = "regulator-fixed"; regulator-name = "vreg_conn_1p8"; startup-delay-us = <4000>; enable-active-high; gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>; }; vreg_conn_pa: regulator-conn-pa { compatible = "regulator-fixed"; regulator-name = "vreg_conn_pa"; startup-delay-us = <4000>; enable-active-high; gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>; }; regulator-usb2-vbus { compatible = "regulator-fixed"; regulator-name = "USB2_VBUS"; gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; pinctrl-0 = <&usb2_en>; pinctrl-names = "default"; enable-active-high; regulator-always-on; }; vreg_v3p3_can: regulator-v3p3-can { compatible = "regulator-fixed"; regulator-name = "vreg-v3p3-can"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-boot-on; regulator-always-on; }; vreg_v5p0_can: regulator-v5p0-can { compatible = "regulator-fixed"; regulator-name = "vreg-v5p0-can"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-boot-on; regulator-always-on; }; wcn6855-pmu { compatible = "qcom,wcn6855-pmu"; pinctrl-0 = <&bt_en_state>, <&wlan_en_state>; pinctrl-names = "default"; bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; wlan-enable-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>; vddio-supply = <&vreg_conn_pa>; vddaon-supply = <&vreg_s5a>; vddpmu-supply = <&vreg_conn_1p8>; vddpmumx-supply = <&vreg_conn_1p8>; vddpmucx-supply = <&vreg_conn_pa>; vddrfa0p95-supply = <&vreg_s5a>; vddrfa1p3-supply = <&vreg_s6a>; vddrfa1p9-supply = <&vreg_l15a>; vddpcie1p3-supply = <&vreg_s6a>; vddpcie1p9-supply = <&vreg_l15a>; regulators { vreg_pmu_rfa_cmn: ldo0 { regulator-name = "vreg_pmu_rfa_cmn"; }; vreg_pmu_aon_0p59: ldo1 { regulator-name = "vreg_pmu_aon_0p59"; }; vreg_pmu_wlcx_0p8: ldo2 { regulator-name = "vreg_pmu_wlcx_0p8"; }; vreg_pmu_wlmx_0p85: ldo3 { regulator-name = "vreg_pmu_wlmx_0p85"; }; vreg_pmu_btcmx_0p85: ldo4 { regulator-name = "vreg_pmu_btcmx_0p85"; }; vreg_pmu_rfa_0p8: ldo5 { regulator-name = "vreg_pmu_rfa_0p8"; }; vreg_pmu_rfa_1p2: ldo6 { regulator-name = "vreg_pmu_rfa_1p2"; }; vreg_pmu_rfa_1p7: ldo7 { regulator-name = "vreg_pmu_rfa_1p7"; }; vreg_pmu_pcie_0p9: ldo8 { regulator-name = "vreg_pmu_pcie_0p9"; }; vreg_pmu_pcie_1p8: ldo9 { regulator-name = "vreg_pmu_pcie_1p8"; }; }; }; }; &apps_rsc { regulators-0 { compatible = "qcom,pm8150-rpmh-regulators"; qcom,pmic-id = "a"; vreg_s3a: smps3 { regulator-name = "vreg_s3a"; regulator-min-microvolt = <600000>; regulator-max-microvolt = <650000>; regulator-initial-mode = ; }; vreg_s4a: smps4 { regulator-name = "vreg_s4a"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1829000>; regulator-initial-mode = ; }; vreg_s5a: smps5 { regulator-name = "vreg_s5a"; regulator-min-microvolt = <1896000>; regulator-max-microvolt = <2040000>; regulator-initial-mode = ; }; vreg_s6a: smps6 { regulator-name = "vreg_s6a"; regulator-min-microvolt = <1304000>; regulator-max-microvolt = <1404000>; regulator-initial-mode = ; }; vreg_l1a: ldo1 { regulator-name = "vreg_l1a"; regulator-min-microvolt = <488000>; regulator-max-microvolt = <852000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l2a: ldo2 { regulator-name = "vreg_l2a"; regulator-min-microvolt = <1650000>; regulator-max-microvolt = <3100000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l3a: ldo3 { regulator-name = "vreg_l3a"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1248000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l5a: ldo5 { regulator-name = "vreg_l5a"; regulator-min-microvolt = <875000>; regulator-max-microvolt = <975000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l7a: ldo7 { regulator-name = "vreg_l7a"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1900000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l8a: ldo8 { regulator-name = "vreg_l8a"; regulator-min-microvolt = <1150000>; regulator-max-microvolt = <1350000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l10a: ldo10 { regulator-name = "vreg_l10a"; regulator-min-microvolt = <2950000>; regulator-max-microvolt = <3312000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l11a: ldo11 { regulator-name = "vreg_l11a"; regulator-min-microvolt = <1232000>; regulator-max-microvolt = <1260000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l12a: ldo12 { regulator-name = "vreg_l12a"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1890000>; regulator-initial-mode = ; }; vreg_l13a: ldo13 { regulator-name = "vreg_l13a"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3230000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l15a: ldo15 { regulator-name = "vreg_l15a"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1904000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l16a: ldo16 { regulator-name = "vreg_l16a"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3312000>; regulator-initial-mode = ; regulator-allow-set-load; regulator-allowed-modes = ; }; vreg_l17a: ldo17 { regulator-name = "vreg_l17a"; regulator-min-microvolt = <2950000>; regulator-max-microvolt = <3312000>; regulator-initial-mode = ; }; }; }; &gpi_dma0 { status = "okay"; }; &gpi_dma1 { status = "okay"; }; &i2c5 { clock-frequency = <400000>; status = "okay"; eeprom@57 { compatible = "atmel,24c02"; reg = <0x57>; pagesize = <16>; }; eeprom@5f { compatible = "atmel,24mac602"; reg = <0x5f>; pagesize = <16>; }; }; &mdss { status = "okay"; }; &mdss_dp0 { status = "okay"; }; &mdss_dp0_out { link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; remote-endpoint = <&dp0_connector_in>; }; &mdss_dsi0 { vdda-supply = <&vreg_l11a>; status = "okay"; }; &mdss_dsi0_phy { vcca-supply = <&vreg_l5a>; status = "okay"; }; &pcie { perst-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; pinctrl-0 = <&pcie_default_state>; pinctrl-names = "default"; status = "okay"; }; &pcie_phy { vdda-phy-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; status = "okay"; }; &pcie_port0 { wifi@0 { compatible = "pci17cb,1103"; reg = <0x10000 0x0 0x0 0x0 0x0>; qcom,calibration-variant = "QC_QCS615_Ride"; vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; vddaon-supply = <&vreg_pmu_aon_0p59>; vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; }; }; &pm8150_gpios { usb2_en: usb2-en-state { pins = "gpio10"; function = "normal"; output-enable; power-source = <0>; }; }; &qupv3_id_0 { status = "okay"; }; &qupv3_id_1 { status = "okay"; }; &remoteproc_adsp { firmware-name = "qcom/qcs615/adsp.mbn"; status = "okay"; }; &remoteproc_cdsp { firmware-name = "qcom/qcs615/cdsp.mbn"; status = "okay"; }; &sdhc_1 { pinctrl-0 = <&sdc1_state_on>; pinctrl-1 = <&sdc1_state_off>; pinctrl-names = "default", "sleep"; bus-width = <8>; mmc-ddr-1_8v; mmc-hs200-1_8v; mmc-hs400-1_8v; mmc-hs400-enhanced-strobe; vmmc-supply = <&vreg_l17a>; vqmmc-supply = <&vreg_s4a>; non-removable; no-sd; no-sdio; status = "okay"; }; &spi6 { status = "okay"; can@0 { compatible = "microchip,mcp2515"; reg = <0>; clocks = <&can_osc>; interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>; spi-max-frequency = <10000000>; vdd-supply = <&vreg_v3p3_can>; xceiver-supply = <&vreg_v5p0_can>; }; }; &tlmm { bt_en_state: bt-en-state { pins = "gpio85"; function = "gpio"; bias-pull-down; }; cam1_reset_default: cam1-reset-default-state { pins = "gpio29"; function = "gpio"; drive-strength = <2>; bias-disable; }; pcie_default_state: pcie-default-state { clkreq-pins { pins = "gpio90"; function = "pcie_clk_req"; drive-strength = <2>; bias-pull-up; }; perst-pins { pins = "gpio89"; function = "gpio"; drive-strength = <2>; bias-pull-down; }; wake-pins { pins = "gpio100"; function = "gpio"; drive-strength = <2>; bias-pull-up; }; }; wifi_reg_en_pins_state: wifi-reg-en-pins-state { pins = "gpio91"; function = "gpio"; drive-strength = <8>; output-high; bias-pull-up; }; wlan_en_state: wlan-en-state { pins = "gpio84"; function = "gpio"; drive-strength = <16>; bias-pull-up; }; }; &uart0 { status = "okay"; }; &uart7 { status = "okay"; bluetooth { compatible = "qcom,wcn6855-bt"; firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv"; vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; vddaon-supply = <&vreg_pmu_aon_0p59>; vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>; vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>; }; }; /* * USB0 routing and EDL mode: * * The USB0 controller’s HS differential pair is switched (manually) * between the Micro-USB port for EDL/ADB and the on-board USB 3.0 hub. * * During EDL (Emergency Download) mode, the HS lines are explicitly * routed to the Micro-USB port to allow the SoC to enter device mode * for flashing. * * After EDL the switch is normally toggled so the HS lines stay * connected to the hub’s Type-A downstream ports, leaving no electrical * path to the Micro-USB connector — therefore USB0 runs host-only in * normal runtime and device mode must not be advertised. * * USB0 is configured host-only in the base device tree; a separate * device-tree overlay enables the Micro-USB peripheral configuration for * ADB. For ADB to work during normal runtime the DIP switch SW1 must be * manually toggled to the off position (reconnecting the HS pair to the * Micro-USB port). */ &usb_1 { dr_mode = "host"; status = "okay"; }; &usb_1_hsphy { vdd-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; vdda-phy-dpdm-supply = <&vreg_l13a>; status = "okay"; }; &usb_2 { dr_mode = "host"; status = "okay"; }; &usb_2_hsphy { vdd-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; vdda-phy-dpdm-supply = <&vreg_l13a>; status = "okay"; }; &usb_qmpphy { vdda-phy-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; status = "okay"; }; &usb_qmpphy_2 { vdda-phy-supply = <&vreg_l11a>; vdda-pll-supply = <&vreg_l5a>; status = "okay"; }; &ufs_mem_hc { reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>; vcc-supply = <&vreg_l17a>; vcc-max-microamp = <600000>; vccq2-supply = <&vreg_s4a>; vccq2-max-microamp = <600000>; status = "okay"; }; &ufs_mem_phy { vdda-phy-supply = <&vreg_l5a>; vdda-pll-supply = <&vreg_l12a>; status = "okay"; }; &venus { status = "okay"; };