diff options
Diffstat (limited to 'general/HalExtensionSample/HalExtSampleTimers2')
5 files changed, 0 insertions, 993 deletions
diff --git a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.c b/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.c deleted file mode 100644 index 9a580fea..00000000 --- a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.c +++ /dev/null @@ -1,825 +0,0 @@ -/*++ - -Copyright (c) 2011 Microsoft Corporation - -Module Name: - - HalExtSampleTimers2.c - -Abstract: - - This file implements a HAL Extension Module for the fictitious EG2Timer. - -Author: - - Evan Green (evgreen) 8-Jan-2011 - ---*/ - -// -// ------------------------------------------------------------------- Includes -// - -#include <nthalext.h> - -// -// -------------------------------------------------------------- Specification -// - -// -// The EG2Timer is a fast-access low latency deadline-based timer designed -// for high-performance timekeeping operations. It consists of one counter -// counter and three match registers against that counter. Each match register -// consists of a 32-bit value that is compared on each clock cycle to the -// current count value. If the values match and the match register is enabled -// for generating an interrupt, an edge triggered interrupt will be fired. The -// register can also be configured with an "interval" value such that the -// match register is automatically moved forward by the given interval to -// generate periodic interrupts. The main counter is 32 bits and runs at 15MHz. -// The register layout of the timer block appears below. -// -// Offset Register Size -// 0x00 GlobalControl 4 -// 0x04 CounterValue 4 -// 0x08 Timer0_Match 4 -// 0x0C Timer0_Interval 4 -// 0x10 Timer0_Control 4 -// 0x14 Timer1_Match 4 -// 0x18 Timer1_Interval 4 -// 0x1C Timer1_Control 4 -// 0x20 Timer2_Match 4 -// 0x24 Timer2_Interval 4 -// 0x28 Timer2_Control 4 -// -// Register Descriptions: -// -// GlobalControl - Controls global state relating to the timer block. On reset, -// this register's value is 0. This register is Read/Write. -// -// Bit Function -// 31-1 Reserved. Read as 0, always write 0 to maintain future -// compatibility. -// -// 0 Enabled. When set to 1, the main counter is enabled and will -// count. When set to 0, the main counter is disabled and will -// not run. -// -// CounterValue - A Read/Write register containing the current value of the -// counter. Writes to this register must be done with caution as they do -// not alter or adjust the contents of the match registers. On reset, the -// value of this register is 0. -// -// TimerN_Match - A Read/Write register that contains the match value that this -// interrupt is primed against. When the global counter equals the match -// value, an interrupt will be generated. If the interrupt is set for -// periodic mode, the Interval value will be automatically added to the -// match value when the interrupt occurs. On reset, the value of this -// register is 0. -// -// TimerN_Interval - A Read/Write register that contains the periodic interval -// to add to the match register if the interrupt is armed for periodic -// mode. On reset, the value of this register is 0. -// -// TimerN_Control - A Read/Write register containing a bitfield that controls -// the behavior of the match register and associated interrupt. On reset, -// the value of this register is 0. -// -// Bit Function -// 31-2 Reserved. Read as 0, always write 0 to maintain future -// compatibility. -// -// 1 Periodic. When set to 1, the value in the Interval register will -// automatically be added to the value in the Match register and -// written back to the Match register when a match occurs. When -// set to 0, the Match register will not change when a match -// occurs. -// -// 0 InterruptEnable. When set to 1, an interrupt will be generated -// when a match occurs. When set to 0, no interrupt will be -// generated when a match occurs. The periodic bit is still live -// however, the Match register will continue to get accumulated -// with the Interval register on matches. -// - -// -// ---------------------------------------------------------------- Definitions -// - -// -// Define the total size of the register block, which is 1 page. -// - -#define EG2TIMER_BLOCK_SIZE 0x1000 - -// -// Define the size of one timer's match register block, in ULONGs. -// - -#define EG2MATCH_SIZE 3 - -// -// Define the total number of match registers. -// - -#define EG2MATCH_COUNT 3 - -// -// Define the timer's bit width. -// - -#define EG2TIMER_BIT_WIDTH 32 - -// -// Define the counter's frequency, in Hertz. -// - -#define EG2TIMER_FREQUENCY 15000000 - -// -// Define the global control bits. -// - -#define EG2TIMER_GLOBAL_CONTROL_ENABLE 0x00000001 - -// -// Define bits for the control register. -// - -#define EG2TIMER_MATCH_INTERRUPT_ENABLE 0x00000001 -#define EG2TIMER_MATCH_PERIODIC 0x00000002 - -// -// Define the special offset used to indicate this timer is the counter -// itself. -// - -#define EG2TIMER_COUNTER_OFFSET 0xFFFFFFFF - -// -// ------------------------------------------------------ Data Type Definitions -// - - -// -// Define the registers and their offsets, in ULONGs. -// - -typedef enum _EG2TIMER_REGISTER { - Eg2TimerGlobalControl = 0, - Eg2TimerCurrentCount = 1, - Eg2TimerMatch = 2, - Eg2TimerInterval = 3, - Eg2TimerControl = 4 -} EG2TIMER_REGISTER, *PEG2TIMER_REGISTER; - -// -// Define the format of the private data structure. The offset member stores the -// offset to the match register, in ULONGs. The value 0 is reserved for the -// global counter. -// - -typedef struct _EG2TIMER_DATA { - ULONG Offset; - TIMER_MODE Mode; - ULONG Period; -} EG2TIMER_DATA, *PEG2TIMER_DATA; - -// -// --------------------------------------------------------------------- Macros -// - -// -// The following macros are used to read from and write to the timer. The first -// parameter is the offset in ULONGs to apply to the requested register. The -// second parameter is the register to read or write. For write functions, the -// third parameter is the value to write. -// -// READ_REGISTER_ULONG and WRITE_REGISTER_ULONG should always be used to -// ensure that the proper barriers and flushes are in place for doing direct -// hardware accesses. -// - -#define READ_EG2TIMER(_TimerOffset, _Register) \ - READ_REGISTER_ULONG((PULONG)Eg2TimerBase + (_TimerOffset) + (_Register)) - -#define WRITE_EG2TIMER(_TimerOffset, _Register, _Value) \ - WRITE_REGISTER_ULONG((PULONG)Eg2TimerBase + (_TimerOffset) + (_Register), \ - (_Value)) - -// -// ----------------------------------------------- Internal Function Prototypes -// - -NTSTATUS -Eg2TimerRegister ( - __in ULONG Handle, - __in PCSRT_RESOURCE_GROUP_HEADER ResourceGroup - ); - -_Function_class_(TIMER_INITIALIZE) -NTSTATUS -Eg2TimerInitialize ( - __in PVOID TimerData - ); - -_Function_class_(TIMER_QUERY_COUNTER) -ULONGLONG -Eg2TimerQueryCounter ( - __in PVOID TimerData - ); - -_Function_class_(TIMER_ACKNOWLEDGE_INTERRUPT) -VOID -Eg2TimerAcknowledgeInterrupt ( - __in PVOID TimerData - ); - -_Function_class_(TIMER_ARM_TIMER) -NTSTATUS -Eg2TimerArm ( - __in PVOID TimerData, - __in TIMER_MODE Mode, - __in ULONGLONG TickCount - ); - -_Function_class_(TIMER_STOP) -VOID -Eg2TimerStop ( - __in PVOID TimerData - ); - -// -// -------------------------------------------------------------------- Globals -// - -// -// Define the physical address of the timer block. This information can either -// be hardcoded like it is here or fetched out of the CSRT resource passed to -// the extension. -// - -ULONGLONG Eg2TimerPhysicalAddress = 0xBEEF7AC0; - -// -// Define the GSIVs for each timer's interrupt. This is also a candidate for -// information to be retrieved out of the CSRT. -// - -ULONG Eg2TimerGsi[EG2MATCH_COUNT] = { - 40, - 41, - 42, -}; - -// -// Define the mapped virtual address of the timer block. -// - -PVOID Eg2TimerBase = NULL; - -// -// ------------------------------------------------------------------ Functions -// - -NTSTATUS -AddResourceGroup ( - __in ULONG Handle, - __in PCSRT_RESOURCE_GROUP_HEADER ResourceGroup - ) - -/*++ - -Routine Description: - - This routine identifies and registers all of the Resource Descriptors - in the specified Resource Group. - -Arguments: - - Handle - Supplies the HAL Extension handle which must be passed to other - HAL Extension APIs. - - ResourceGroup - Supplies a pointer to the Resource Group which the - HAL Extension has been installed on. - -Return Value: - - NTSTATUS code. - ---*/ - -{ - - NTSTATUS Status; - - // - // Register the main timer block. - // - - Status = Eg2TimerRegister(Handle, ResourceGroup); - if (!NT_SUCCESS(Status)) { - goto AddResourceGroupEnd; - } - - Status = STATUS_SUCCESS; - -AddResourceGroupEnd: - return Status; -} - -// -// --------------------------------------------------------- Internal Functions -// - -NTSTATUS -Eg2TimerRegister ( - __in ULONG Handle, - __in PCSRT_RESOURCE_GROUP_HEADER ResourceGroup - ) - -/*++ - -Routine Description: - - This routine registers the EG2 Timer hardware. - -Arguments: - - Handle - Supplies the HAL Extension handle which must be passed to other - HAL Extension APIs. - - ResourceGroup - Supplies a pointer to the Resource Group which the - HAL Extension has been installed on. - -Return Value: - - NT status code. - ---*/ - -{ - - EG2TIMER_DATA InternalData; - TIMER_INITIALIZATION_BLOCK NewTimer; - PHYSICAL_ADDRESS PhysicalAddress; - CSRT_RESOURCE_DESCRIPTOR_HEADER ResourceDescriptorHeader; - NTSTATUS Status; - ULONG TimerIndex; - - // - // DEV HACK: Makeup a resource type until we get correct CSRT parsing. - // - - ResourceDescriptorHeader.Type = CSRT_RD_TYPE_TIMER; - ResourceDescriptorHeader.Subtype = CSRT_RD_SUBTYPE_TIMER; - ResourceDescriptorHeader.Length = sizeof(CSRT_RESOURCE_DESCRIPTOR_HEADER); - - // - // Register the entire timer block's address usage with the HAL. This - // address space should be shown to the HAL as reserved even if the timer - // is not going to be registered or used so that the system knows that - // region of *physical* address space is occupied. - // - - PhysicalAddress.QuadPart = Eg2TimerPhysicalAddress; - Status = HalRegisterPermanentAddressUsage(PhysicalAddress, - EG2TIMER_BLOCK_SIZE); - - if (!NT_SUCCESS(Status)) { - goto RegisterEnd; - } - - // - // Register the main counter as a non-interrupt generating timer, as it can - // be used completely independently of the match registers as long as it - // is never written to. - // - - RtlZeroMemory(&NewTimer, sizeof(TIMER_INITIALIZATION_BLOCK)); - RtlZeroMemory(&InternalData, sizeof(EG2TIMER_DATA)); - INITIALIZE_TIMER_HEADER(&NewTimer); - NewTimer.CounterBitWidth = EG2TIMER_BIT_WIDTH; - NewTimer.CounterFrequency = EG2TIMER_FREQUENCY; - - // - // Set the pointer to the internal data and its size. The pointer can - // be the same for each timer (and a local variable) because a *copy* - // of this data will be made for each timer registered. This is the - // extensions only chance to dynamically allocate memory. - // - - NewTimer.InternalData = &InternalData; - NewTimer.InternalDataSize = sizeof(EG2TIMER_DATA); - NewTimer.Interrupt.Mode = Latched; - NewTimer.Interrupt.Polarity = InterruptActiveHigh; - - // - // This must be set to indicate that this is a custom third-party timer. - // The HAL will fail the registration if this is not set correctly. - // - - NewTimer.KnownType = TimerUnknown; - - // - // The timer does not support a divisor. The GSI data can be hardcoded - // like it is here or pulled out of the resource from the CSRT table. - // Filling in extra functions doesn't hurt as the HAL will never call - // anything but Initialize and QueryCounter on timers that don't - // generate interrupts. - // - - NewTimer.MaxDivisor = 1; - NewTimer.FunctionTable.Initialize = Eg2TimerInitialize; - NewTimer.FunctionTable.QueryCounter = Eg2TimerQueryCounter; - NewTimer.FunctionTable.AcknowledgeInterrupt = Eg2TimerAcknowledgeInterrupt; - NewTimer.FunctionTable.ArmTimer = Eg2TimerArm; - NewTimer.FunctionTable.Stop = Eg2TimerStop; - NewTimer.Capabilities = TIMER_COUNTER_READABLE; - InternalData.Offset = EG2TIMER_COUNTER_OFFSET; - ResourceDescriptorHeader.Uid = EG2TIMER_COUNTER_OFFSET; - Status = RegisterResourceDescriptor(Handle, - ResourceGroup, - &ResourceDescriptorHeader, - &NewTimer); - - if (!NT_SUCCESS(Status)) { - goto RegisterEnd; - } - - - // - // Register each match register as a separate non-readable timer with the - // HAL. Since this timer is deadline-based, it can do pseudo-periodic - // mode and lossless rate transitions. - // - - NewTimer.Capabilities = TIMER_ONE_SHOT_CAPABLE | - TIMER_PERIODIC_CAPABLE | - TIMER_PSEUDO_PERIODIC_CAPABLE | - TIMER_GENERATES_LINE_BASED_INTERRUPTS; - - for (TimerIndex = 0; TimerIndex < EG2MATCH_COUNT; TimerIndex += 1) { - NewTimer.Interrupt.Gsi = Eg2TimerGsi[TimerIndex]; - InternalData.Offset = EG2MATCH_SIZE * TimerIndex; - ResourceDescriptorHeader.Uid = EG2MATCH_SIZE * TimerIndex; - Status = RegisterResourceDescriptor(Handle, - ResourceGroup, - &ResourceDescriptorHeader, - &NewTimer); - - if (!NT_SUCCESS(Status)) { - goto RegisterEnd; - } - } - - Status = STATUS_SUCCESS; - -RegisterEnd: - return Status; -} - -_Function_class_(TIMER_INITIALIZE) -NTSTATUS -Eg2TimerInitialize ( - __in PVOID TimerData - ) - -/*++ - -Routine Description: - - This routine is responsible for initializing the timer hardware. This is - guaranteed to be the first timer routine called by the HAL. It must prepare - the timer for use by beginning the timer's counter ticking if the counter - is readable, setting the intial input clock divisor to 1 if applicable, - and masking all interrupts. If the timer's stop routine is called, this - routine will be called before the timer is queried or armed again. It will - not be called between every rearming of the timer. - - This routine will not be called concurrently with any other calls to - this HAL Timer extension. For per-processor timers, this routine will be - called once on each processor. A failure on any processor blocks the timer's - use on all processors. - -Arguments: - - TimerData - Supplies a pointer to the timer's private context. The contents - of this pointer were specified when the timer was initially registered, - and may be modified inside this routine. The HAL does not interpret any - data deferenced from this pointer. - -Return Value: - - Returns an NT status code indicating success or failure. If a successful - status code is returned then the HAL may subsequently call further routines - in this HAL extension to query or arm the timer. If a failure code is - returned, this HAL extension will not attempt to use this timer unless the - Initialize routine is called again and succeeds. - ---*/ - -{ - - PHYSICAL_ADDRESS PhysicalAddress; - NTSTATUS Status; - PEG2TIMER_DATA Timer; - - Timer = (PEG2TIMER_DATA)TimerData; - - // - // Map the timer if no one has done that yet. - // - - if (Eg2TimerBase == NULL) { - PhysicalAddress.QuadPart = Eg2TimerPhysicalAddress; - Eg2TimerBase = HalMapIoSpace(PhysicalAddress, - EG2TIMER_BLOCK_SIZE, - MmNonCached); - - if (Eg2TimerBase == NULL) { - Status = STATUS_INSUFFICIENT_RESOURCES; - goto InitializeEnd; - } - } - - // - // Start the counter ticking in free running mode, and mask all interrupts. - // The counter must *not* be reset here, otherwise an Initialize call on the - // counter would affect the match register timers, which as far as the HAL - // is concerned are completely independent from one another. - // - - WRITE_EG2TIMER(0, Eg2TimerGlobalControl, EG2TIMER_GLOBAL_CONTROL_ENABLE); - if (Timer->Offset != EG2TIMER_COUNTER_OFFSET) { - WRITE_EG2TIMER(Timer->Offset, Eg2TimerControl, 0); - } - - Status = STATUS_SUCCESS; - -InitializeEnd: - return Status; -} - -_Function_class_(TIMER_QUERY_COUNTER) -ULONGLONG -Eg2TimerQueryCounter ( - __in PVOID TimerData - ) - -/*++ - -Routine Description: - - This routine queries the timer hardware and retrieves the current counter - value. - - Timers are assumed to always count *up*. If the actual timer hardware counts - down, then this routine should subtract the current count from the maximum - counter value so that values appear to count up. This routine may be called - concurrently on multiple processors and must be reentrant. This routine is - extremely performance sensitive, as it may be used to back the system - performance counter. - -Arguments: - - TimerData - Supplies a pointer to the timer's private context, whose - initial content was supplied when the timer was registered. - -Return Value: - - Returns the hardware's current count. - ---*/ - -{ - - PEG2TIMER_DATA Timer; - - Timer = (PEG2TIMER_DATA)TimerData; - - NT_ASSERT(Timer->Offset == EG2TIMER_COUNTER_OFFSET); - - return READ_EG2TIMER(Timer->Offset, Eg2TimerCurrentCount); -} - -_Function_class_(TIMER_ACKNOWLEDGE_INTERRUPT) -VOID -Eg2TimerAcknowledgeInterrupt ( - __in PVOID TimerData - ) - -/*++ - -Routine Description: - - This routine performs any actions necessary to acknowledge and quiesce a - timer interrupt. For per-processor timers, this routine may be called - concurrently on multiple processors. This routine will be called on every - timer interrupt at the hardware priority level of that interrupt, so this - routine is extremely performance sensitive. For timers running in - pseudo-periodic mode, this routine must rearm the timer for the same - interval as it was armed with without introducing delay into the interrupt - interval. Only deadline-based timers support pseudo-periodic mode. - -Arguments: - - TimerData - Supplies a pointer to the timer's private context, whose - initial content was supplied when the timer was registered. - -Return Value: - - None. - ---*/ - -{ - - ULONG MatchValue; - PEG2TIMER_DATA Timer; - - // - // No action is necessary here as far as acknowledging the interrupt. - // If the current mode is pseudo-periodic, the next interrupt must be - // armed now. - // - - Timer = (PEG2TIMER_DATA)TimerData; - - NT_ASSERT(Timer->Offset != EG2TIMER_COUNTER_OFFSET); - NT_ASSERT(Timer->Mode != TimerModeInvalid); - - if (Timer->Mode == TimerModePseudoPeriodic) { - - NT_ASSERT(Timer->Period != 0); - - // - // Read the deadline that just passed, add the period, and then write - // the new deadline. - // - - MatchValue = READ_EG2TIMER(Timer->Offset, Eg2TimerMatch); - MatchValue += Timer->Period; - WRITE_EG2TIMER(Timer->Offset, Eg2TimerMatch, MatchValue); - } - - return; -} - -_Function_class_(TIMER_ARM_TIMER) -NTSTATUS -Eg2TimerArm ( - __in PVOID TimerData, - __in TIMER_MODE Mode, - __in ULONGLONG TickCount - ) - -/*++ - -Routine Description: - - This routine arms a timer to fire an interrupt after the given number of - timer ticks. For timers that only interrupt on rollovers, this simply - enables the interrupt, the tick count parameter is ignored. If the timer - is currently armed for a different mode or tick count, this call is - expected to replace that programming. This routine will not get called - concurrently with other timer calls, except on per-processor timers, where - it may get called concurrently on different processors. - -Arguments: - - TimerData - Supplies a pointer to the timer's private context, whose - initial content was supplied when the timer was registered. - - Mode - Supplies the mode to arm the timer in, which will be one of the - modes the HAL extension advertised support for when registering the - timer. The modes are as follows: - - OneShot - Arms the timer to fire the given number of ticks from now. - Only one interrupt is expected to come in. The HAL does not make - assumptions on whether or not the expiration of this interrupt - causes the counter to stop. The Query Counter routine will not be - called while a timer is armed to fire an interrupt. - - Periodic - Arms the timer to fire periodically with an interval of the - given number of ticks. The first interrupt should happen - approximately the given number of ticks from when the arm timer - function was invoked. - - PseudoPeriodic - Arms the timer with the same functional behavior as - periodic mode, with the knowledge that the timer will have to rearm - itself during the acknowledge interrupt routine. This mode is - expected to have slightly worse performance than pure periodic mode, - but is expected to generate periodic interrupts at the exact rate - specified. - - TickCount - Supplies the number of ticks from now that the timer should - assert its interrupt in. For timers that are only capable of - interrupting on rollovers from their maximum value to 0, this parameter - is ignored. - -Return Value: - - Returns and NTSTATUS code indicating success or failure. If the timer - returns success, then the interrupt is expected to come in the specified - number of ticks from when the function was called, with a tolerance of - however long the function took to execute. If the routine fails, then no - timer routines will be called again until the timer Initialize routine is - called again and succeeds. In most cases, returning a failure code results - in a system bugcheck. - ---*/ - -{ - - ULONG ControlRegister; - ULONG MatchValue; - PEG2TIMER_DATA Timer; - - Timer = (PEG2TIMER_DATA)TimerData; - - NT_ASSERT(TickCount != 0); - NT_ASSERT(TickCount <= 0xFFFFFFFF); - NT_ASSERT(Timer->Offset != EG2TIMER_COUNTER_OFFSET); - - // - // This will never occur. - // - - if ((TickCount > 0xFFFFFFFF) || (TickCount == 0)) { - return STATUS_INVALID_PARAMETER; - } - - // - // Disable the timer while it's being programmed to avoid spurious - // interrupts. - // - - WRITE_EG2TIMER(Timer->Offset, Eg2TimerControl, 0); - ControlRegister = EG2TIMER_MATCH_INTERRUPT_ENABLE; - - // - // For periodic mode, set the periodic interval register. - // - - if (Mode == TimerModePeriodic) { - ControlRegister |= EG2TIMER_MATCH_PERIODIC; - WRITE_EG2TIMER(Timer->Offset, Eg2TimerInterval, (ULONG)TickCount); - } - - Timer->Mode = Mode; - Timer->Period = (ULONG)TickCount; - - // - // Calculate and write in the first match value. - // - - MatchValue = READ_EG2TIMER(Timer->Offset, Eg2TimerCurrentCount); - MatchValue += (ULONG)TickCount; - WRITE_EG2TIMER(Timer->Offset, Eg2TimerMatch, MatchValue); - - // - // Enable the interrupt. - // - - WRITE_EG2TIMER(Timer->Offset, Eg2TimerControl, ControlRegister); - return STATUS_SUCCESS; -} - -_Function_class_(TIMER_STOP) -VOID -Eg2TimerStop ( - __in PVOID TimerData - ) - -/*++ - -Routine Description: - - This routine stops a timer from ticking. After this function returns, the - timer should not generate any more interrupts, and reads to its counter - might return the same value every time. - -Arguments: - - TimerData - Supplies a pointer to the timer's private context, whose - initial content was supplied when the timer was registered. - -Return Value: - - None, this function must succeed. - ---*/ - -{ - - PEG2TIMER_DATA Timer; - - Timer = (PEG2TIMER_DATA)TimerData; - - // - // Clear the interrupt enable bit. - // - - WRITE_EG2TIMER(Timer->Offset, Eg2TimerControl, 0); - return; -} diff --git a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.def b/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.def deleted file mode 100644 index 685129d2..00000000 --- a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.def +++ /dev/null @@ -1,2 +0,0 @@ -LIBRARY HalExtSampleTimers2 - diff --git a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.rc b/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.rc deleted file mode 100644 index c82378e0..00000000 --- a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.rc +++ /dev/null @@ -1,10 +0,0 @@ -#include "verrsrc.h" -#include <ntverp.h> - -#define VER_FILETYPE VFT_DLL -#define VER_FILESUBTYPE VFT_UNKNOWN -#define VER_FILEDESCRIPTION_STR "HAL Extension Sample - Timers 2" -#define VER_INTERNALNAME_STR "HalExtSampleTimers2.DLL" -#define VER_ORIGINALFILENAME_STR "HalExtSampleTimers2.DLL" - -#include <common.ver> diff --git a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj b/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj deleted file mode 100644 index dc581c00..00000000 --- a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj +++ /dev/null @@ -1,126 +0,0 @@ -<?xml version="1.0" encoding="utf-8"?> -<Project DefaultTargets="Build" ToolsVersion="12.0" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> - <ItemGroup Label="ProjectConfigurations"> - <ProjectConfiguration Include="Debug|Arm"> - <Configuration>Debug</Configuration> - <Platform>Arm</Platform> - </ProjectConfiguration> - <ProjectConfiguration Include="Release|Arm"> - <Configuration>Release</Configuration> - <Platform>Arm</Platform> - </ProjectConfiguration> - </ItemGroup> - <PropertyGroup Label="Globals"> - <ProjectGuid>{A99E0448-5F6C-42B3-99AA-C43464989418}</ProjectGuid> - <RootNamespace>$(MSBuildProjectName)</RootNamespace> - <KMDF_VERSION_MAJOR>1</KMDF_VERSION_MAJOR> - <Configuration Condition="'$(Configuration)' == ''">Debug</Configuration> - <Platform Condition="'$(Platform)' == ''">Arm</Platform> - <SampleGuid>{E9FE899A-F0DB-43B5-8DFD-65D5D790DD76}</SampleGuid> - </PropertyGroup> - <Import Project="$(VCTargetsPath)\Microsoft.Cpp.Default.props" /> - <PropertyGroup Label="Configuration" Condition="'$(Configuration)|$(Platform)'=='Release|Arm'"> - <TargetVersion>Windows10</TargetVersion> - <UseDebugLibraries>False</UseDebugLibraries> - <DriverTargetPlatform>Universal</DriverTargetPlatform> - <DriverType /> - <PlatformToolset>WindowsApplicationForDrivers10.0</PlatformToolset> - <ConfigurationType>DynamicLibrary</ConfigurationType> - </PropertyGroup> - <PropertyGroup Label="Configuration" Condition="'$(Configuration)|$(Platform)'=='Debug|Arm'"> - <TargetVersion>Windows10</TargetVersion> - <UseDebugLibraries>True</UseDebugLibraries> - <DriverTargetPlatform>Universal</DriverTargetPlatform> - <DriverType /> - <PlatformToolset>WindowsApplicationForDrivers10.0</PlatformToolset> - <ConfigurationType>DynamicLibrary</ConfigurationType> - </PropertyGroup> - <Import Project="$(VCTargetsPath)\Microsoft.Cpp.props" /> - <PropertyGroup> - <OutDir>$(IntDir)</OutDir> - </PropertyGroup> - <ImportGroup Label="PropertySheets" Condition="'$(Configuration)|$(Platform)'=='Release|Arm'"> - <Import Project="$(UserRootDir)\Microsoft.Cpp.$(Platform).user.props" Condition="exists('$(UserRootDir)\Microsoft.Cpp.$(Platform).user.props')" /> - </ImportGroup> - <ImportGroup Label="PropertySheets" Condition="'$(Configuration)|$(Platform)'=='Debug|Arm'"> - <Import Project="$(UserRootDir)\Microsoft.Cpp.$(Platform).user.props" Condition="exists('$(UserRootDir)\Microsoft.Cpp.$(Platform).user.props')" /> - </ImportGroup> - <ItemGroup Label="WrappedTaskItems" /> - <ItemDefinitionGroup Condition="'$(Configuration)|$(Platform)'=='Release|Arm'"> - <Link> - <EntryPointSymbol Condition="'$(Platform)'=='win32'">HalExtensionInit@12</EntryPointSymbol> - <EntryPointSymbol Condition="'$(Platform)'!='win32'">HalExtensionInit</EntryPointSymbol> - </Link> - </ItemDefinitionGroup> - <ItemDefinitionGroup Condition="'$(Configuration)|$(Platform)'=='Debug|Arm'"> - <Link> - <EntryPointSymbol Condition="'$(Platform)'=='win32'">HalExtensionInit@12</EntryPointSymbol> - <EntryPointSymbol Condition="'$(Platform)'!='win32'">HalExtensionInit</EntryPointSymbol> - </Link> - </ItemDefinitionGroup> - <PropertyGroup Condition="'$(Configuration)|$(Platform)'=='Release|Arm'"> - <TargetName>HalExtSampleTimers2</TargetName> - </PropertyGroup> - <PropertyGroup Condition="'$(Configuration)|$(Platform)'=='Debug|Arm'"> - <TargetName>HalExtSampleTimers2</TargetName> - </PropertyGroup> - <ItemDefinitionGroup Condition="'$(Configuration)|$(Platform)'=='Release|Arm'"> - <ResourceCompile> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - </ResourceCompile> - <ClCompile> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - <TreatWarningAsError>true</TreatWarningAsError> - <WarningLevel>Level4</WarningLevel> - <AdditionalOptions>%(AdditionalOptions) /J</AdditionalOptions> - <ExceptionHandling> - </ExceptionHandling> - </ClCompile> - <Midl> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - </Midl> - <Link> - <AdditionalDependencies>%(AdditionalDependencies);halextlib.lib;libcntpr.lib;bufferoverflowfastfailk.lib</AdditionalDependencies> - <AdditionalOptions>%(AdditionalOptions) -merge:PAGECONST=PAGE -merge:INITCONST=INIT /LARGEADDRESSAWARE</AdditionalOptions> - <ModuleDefinitionFile>HalExtSampleTimers2.def</ModuleDefinitionFile> - </Link> - </ItemDefinitionGroup> - <ItemDefinitionGroup Condition="'$(Configuration)|$(Platform)'=='Debug|Arm'"> - <ResourceCompile> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - </ResourceCompile> - <ClCompile> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - <TreatWarningAsError>true</TreatWarningAsError> - <WarningLevel>Level4</WarningLevel> - <AdditionalOptions>%(AdditionalOptions) /J</AdditionalOptions> - <ExceptionHandling> - </ExceptionHandling> - </ClCompile> - <Midl> - <AdditionalIncludeDirectories>%(AdditionalIncludeDirectories);$(DDK_INC_PATH)</AdditionalIncludeDirectories> - </Midl> - <Link> - <AdditionalDependencies>%(AdditionalDependencies);halextlib.lib;libcntpr.lib;bufferoverflowfastfailk.lib</AdditionalDependencies> - <AdditionalOptions>%(AdditionalOptions) -merge:PAGECONST=PAGE -merge:INITCONST=INIT /LARGEADDRESSAWARE</AdditionalOptions> - <ModuleDefinitionFile>HalExtSampleTimers2.def</ModuleDefinitionFile> - </Link> - </ItemDefinitionGroup> - <ItemGroup> - <ClCompile Include="HalExtSampleTimers2.c" /> - <ResourceCompile Include="HalExtSampleTimers2.rc" /> - </ItemGroup> - <ItemGroup> - <Inf Exclude="@(Inf)" Include="*.inf" /> - <FilesToPackage Include="$(TargetPath)" Condition="'$(ConfigurationType)'=='Driver' or '$(ConfigurationType)'=='DynamicLibrary'" /> - </ItemGroup> - <ItemGroup> - <None Exclude="@(None)" Include="*.txt;*.htm;*.html" /> - <None Exclude="@(None)" Include="*.ico;*.cur;*.bmp;*.dlg;*.rct;*.gif;*.jpg;*.jpeg;*.wav;*.jpe;*.tiff;*.tif;*.png;*.rc2" /> - <None Exclude="@(None)" Include="*.def;*.bat;*.hpj;*.asmx" /> - </ItemGroup> - <ItemGroup> - <ClInclude Exclude="@(ClInclude)" Include="*.h;*.hpp;*.hxx;*.hm;*.inl;*.xsd" /> - </ItemGroup> - <Import Project="$(VCTargetsPath)\Microsoft.Cpp.targets" /> -</Project>
\ No newline at end of file diff --git a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj.Filters b/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj.Filters deleted file mode 100644 index d752a638..00000000 --- a/general/HalExtensionSample/HalExtSampleTimers2/HalExtSampleTimers2.vcxproj.Filters +++ /dev/null @@ -1,30 +0,0 @@ -<?xml version="1.0" encoding="utf-8"?> -<Project ToolsVersion="4.0" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> - <ItemGroup> - <Filter Include="Source Files"> - <Extensions>cpp;c;cc;cxx;def;odl;idl;hpj;bat;asm;asmx;*</Extensions> - <UniqueIdentifier>{CE019AA9-89F5-4A8E-87D1-ED585767F789}</UniqueIdentifier> - </Filter> - <Filter Include="Header Files"> - <Extensions>h;hpp;hxx;hm;inl;inc;xsd</Extensions> - <UniqueIdentifier>{EF3411D2-5BFE-41A9-906C-0E6611142568}</UniqueIdentifier> - </Filter> - <Filter Include="Resource Files"> - <Extensions>rc;ico;cur;bmp;dlg;rc2;rct;bin;rgs;gif;jpg;jpeg;jpe;resx;tiff;tif;png;wav;mfcribbon-ms;man;xml</Extensions> - <UniqueIdentifier>{07F31510-2D3D-4110-85A6-F39922948329}</UniqueIdentifier> - </Filter> - </ItemGroup> - <ItemGroup> - <ClCompile Include="HalExtSampleTimers2.c"> - <Filter>Source Files</Filter> - </ClCompile> - <None Include="HalExtSampleTimers2.def"> - <Filter>Source Files</Filter> - </None> - </ItemGroup> - <ItemGroup> - <ResourceCompile Include="HalExtSampleTimers2.rc"> - <Filter>Resource Files</Filter> - </ResourceCompile> - </ItemGroup> -</Project>
\ No newline at end of file |