| Age | Commit message (Collapse) | Author |
|---|
|
Add RPMI MPXY proxy driver for LOGGING service group so that
S-mode can leverage LOGGING service group implemented by the
platform microcontroller.
Reviewed-by: Rahul Pathak <[email protected]>
Signed-off-by: Subrahmanya Lingappa <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
PMU_AP_CORE2_IDLE_CFG and PMU_AP_CORE3_IDLE_CFG are not continuous with
PMU_AP_CORE0_IDLE_CFG and PMU_AP_CORE1_IDLE_CFG. They are at PMU AP
base + 0x160 and + 0x164, matching the vendor OpenSBI definitions. After
fixing these addresses, the intermediate cluster offset macros are
redundant now, so define the wakeup and idle registers directly as
PMU_AP_BASE offsets. This makes the actual register addresses easier to
inspect and compare against the vendor code.
C1_RVBADDR_HI_ADDR is also corrected according to the vendor OpenSBI
definition. This was tested by writing an invalid value to the corrected
address, which prevents cluster1 CPUs from coming online, while doing
the same with the old address does not affect SMP boot.
Fixes: 1f84ec2a ("platform: generic: spacemit: add K1")
Signed-off-by: Junhui Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
When JTAG is connected, internal logic leads to the bit
MIPS_CTL0_DBG_RST_DASRT (for the debug unit) stay high and
this prevents normal cluster power-up.
Force proper power-on reset value prior to power-up sequence.
Hold this value for about 10 usec
Signed-off-by: Vladimir Kondratiev <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
During warm reset, my EIC770X/Hifive Premier P550 can sometimes
encounter memory corruption issue crashing Linux boot. Currently the
issue is mitigated by having a sbi_printf before writing to the reset
register. I analyzed the issue further since then. From the SoC
datasheet[1], it's recommended to implement power-down flow as:
a. Designate a primary core, and let it broadcast requests to other
cores to execute a CEASE insn. Primary core also notifies an
"Externel Agent" to start monitoring.
b. Primary core waits for other cores to CEASE before it CEASEs.
c. "External Agent" waits for primary core to CEASE before resets
the Core Complex.
It's possible that EIC770X can trigger undefined behavior if the core
complex is reset while the harts are actively running. The sbi_printf
in the reset handler effectively hides the problem by delaying the
reset -- by the time sbi_printf finishes, all other harts will have
already landed in the loop in sbi_hsm_hart_wait(), which parks the hart.
Without the sbi_printf, I confirmed that other harts haven't reached
sbi_hsm_hart_wait yet before current hart resets the SoC. (by debugging)
To safely reset, and inspired by the datasheet, the warm reset logic
in eic770x.c now use the current hart as both primary core and the
"External Agent", and other harts as secondary cores. It leverages
the HSM framework and a new eic770x_hsm device to CEASE other harts,
and wait for them to CEASE before resets the SoC. with the sbi_printf
before reset removed, and this logic in place, stress test shows that
the memory corruption issue no longer occurs.
The new eic770x_hsm device is only used for the reset-CEASE logic at
the moment, and may be extended to a fully functional HSM device in
the future.
[1] https://github.com/eswincomputing/EIC7700X-SoC-Technical-Reference-Manual
Fixes: e5797e0688c1 ("platform: generic: eswin: add EIC7700")
Signed-off-by: Bo Gan <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Litex SoC controller supports reboot function by toggling the first
bit of the ctrl register. Add a reset driver so other software can
use it.
Signed-off-by: Inochi Amaoto <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Instead of parsing ISA extensions separately for each hart in the
generic_extensions_init() function, it is better to parse ISA extensions
for all available harts in the cold boot path. Also, this allows us
to remove fdt_isa_bitmap from scratch space and directly initialize
"extensions" in struct sbi_hart_features for each hart.
Signed-off-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The payload for FW_PAYLOAD needs to be placed at a 2M/4M aligned address
(for 64/32 bit systems) and the current makefile uses FW_PAYLOAD_OFFSET
to achieve this. This only works if FW_TEXT_START is already 2M/4M
aligned. Most existing physical/virtual platforms have used a
FW_TEXT_START of 0x0 or 0x80000000, so this hasn't been an issue so far.
If, for example, FW_TEXT_START is 0x80000, the payload would end up
placed at 0x280000 on a 64 bit system, which isn't a 2M aligned
address.
Update the makefile to use FW_PAYLOAD_ALIGN instead. This will ensure
that the address picked for the payload is 2M/4M aligned irrespective of
where FW_TEXT_START is.
Signed-off-by: Anirudh Srinivasan <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
PMP functions that deal with hart PMP CSRs are given a sbi_hart_ prefix,
to distinguish from RISC-V PMP encoding functions.
The is_pmp_entry_mapped() function is changed a little more, to align
with other PMP conventions, and made to return a bool to make it more
obvious that it returns a bool and not an SBI_ return code.
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The SpacemiT P1 is a PMIC commonly found with SpacemiT CPU like K1. Add
a reset driver for it.
Signed-off-by: Aurelien Jarno <[email protected]>
Tested-by: Anand Moon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add a simple SpacemiT I2C driver for basic byte transfers over the I2C
bus, prioritizing simplicity over performance. The driver operates in
PIO mode and does not use interrupts, FIFO, or DMA.
The controller is reset at the start of each transaction to ensure a
known initial state, regardless of prior configuration by the kernel.
This also avoids the need for additional error recovery code.
This will be used for communication with onboard PMIC to reset and
power-off the board.
Signed-off-by: Aurelien Jarno <[email protected]>
Tested-by: Anand Moon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add the Tenstorrent Atlantis as a generic-platform. This initial support
enables the single_fw_region option, and verifies and prints HART PMA
CSR configuration.
Signed-off-by: Nicholas Piggin <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
The kendryte/k210 platform does not have MMU support in S-mode hence
only NOMMU kernel which runs in M-mode can be used on this platform.
As of now, there is no clear use-case of supporting OpenSBI for
kendryte/k210 platform.
Signed-off-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add necessary infra for implementing RPMI Management Mode
service group on platform microcontroller.
Co-authored-by: Sunil V L <[email protected]>
Signed-off-by: Ranbir Singh <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Set a default MMIO region with a single SmePMP entry, which allows us
to save entries for M-mode only devices. The default entry has M-/S-mode
shared permission, so system-level resource protection, such as RISC-V
World extension and WorldGuard checker, will be introduced to protect
M-mode only region access from lower privilege modes.
Reviewed-by: Greentime Hu <[email protected]>
Reviewed-by: Zong Li <[email protected]>
Signed-off-by: Yu-Chien Peter Lin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add initial platform support for SiFive development platforms
with the "sifive-dev" compatible string.
Reviewed-by: Greentime Hu <[email protected]>
Reviewed-by: Zong Li <[email protected]>
Signed-off-by: Yu-Chien Peter Lin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add a 32-bit unique ID to plic, aplic, and imsic data which can be
used to differentiate multiple irqchip devices.
Signed-off-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Use a platform-specific compatible to avoid clashing
with CPU compatible
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Conor Dooley <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Signed-off-by: Vladimir Kondratiev <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
P8700 has MIPS specific CSRs. Fix the list, adding
few missing ones and remove few non-existing
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
SBI code arranges domain PMP regions in a way that last entry is
all-inclusive "0..~0 RWX" and the rest of entries are not programmed.
This causes a problem for the eyeq7h.
CPU can issue speculative prefetches to non-existent addresses. If this
access goes to the system NOC, it is mis-interpreted as an access
violation and error is reported, forcing system reset.
To prevent such a speculative transaction to leave a CPU cluster,
block it using PMP, by restricting memory region to physically present
memory. To achieve this, on early init:
- update flags for the last all-inclusive "0..~0 RWX" entry to be
inaccessible MMIO. MMIO serves to set up PMA attributes to uncached
non-prefetchable, preventing transactions to reach system NOC
- add an all-permissive entry matching DRAM.
Resulting memory regions:
Domain0 Region00 : 0x0000000800100000-0x000000080013ffff M: (F,R,X) S/U: ()
Domain0 Region01 : 0x0000000800100000-0x00000008001fffff M: (F,R,W) S/U: ()
Domain0 Region02 : 0x0000000048700000-0x000000004870ffff M: (I,R,W) S/U: ()
Domain0 Region03 : 0x0000000067480000-0x000000006748ffff M: (I,R,W) S/U: ()
Domain0 Region04 : 0x0000000067500000-0x000000006750ffff M: (I,R,W) S/U: ()
Domain0 Region05 : 0x0000000048740000-0x000000004875ffff M: (I,R,W) S/U: ()
Domain0 Region06 : 0x00000000674c0000-0x00000000674dffff M: (I,R,W) S/U: ()
Domain0 Region07 : 0x0000000067540000-0x000000006755ffff M: (I,R,W) S/U: ()
Domain0 Region08 : 0x0000000000000000-0x000000007fffffff M: (I,R,W) S/U: (R,W)
Domain0 Region09 : 0x0000000800000000-0x00000008ffffffff M: () S/U: (R,W,X)
Domain0 Region10 : 0x0000001000000000-0x0000001fffffffff M: (I) S/U: (R,W)
Domain0 Region11 : 0x0000000000000000-0xffffffffffffffff M: (I) S/U: ()
Here Region09 covers DRAM, region 11 set to non-accessible
uncached no-prefetch for the entire address range
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Debug print MMIO regions
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
CPU clusters 1 and 2 cannot access NCORE registers through AUX ports.
AUX ports of clusters 1 and 2 are connected to NCORE through east port.
East port has no access to NCORE registers address space.
Re-route NCORE registers range to MEM port by re-configuring MMIO
regions in the GCR. REsulting map is as below. Mind a gap between
regions [1] and [2]; this gap covering NCORE registers now routed
to the default MEM port
Cluster 0: 4 MMIO regions
[0] : 0x0000000000000000-0x000000001fff0000 AUX0 UC|UCA
[1] : 0x0000000020000000-0x00000000677f0000 AUX0 ANY
[2] : 0x0000000080000000-0x0000001fffff0000 AUX0 UC|UCA
[3] : --disabled--
Cluster 1: 4 MMIO regions
[0] : 0x0000000000000000-0x000000001fff0000 AUX0 UC|UCA
[1] : 0x0000000020000000-0x00000000677f0000 AUX0 ANY
[2] : 0x0000000080000000-0x0000001fffff0000 AUX0 UC|UCA
[3] : --disabled--
Cluster 2: 4 MMIO regions
[0] : 0x0000000000000000-0x000000001fff0000 AUX0 UC|UCA
[1] : 0x0000000020000000-0x00000000677f0000 AUX0 ANY
[2] : 0x0000000080000000-0x0000001fffff0000 AUX0 UC|UCA
[3] : --disabled--
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Use eyeq7 specific method to synchronously restart architectural
mtimer and eyeq7h specific high-resolution timer with common
hardware trigger. This ensures all timers are precisely in sync
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
There's high-resolution (1GHz) timer found in the p8700 cluster.
This timer used for precise time measurement by platform specific
software.
Synchronize this proprietary timers to reference in cluster 0.
Procedure borrowed from the aclint mtimer.
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Switch to GENMASK, EXTRACT_BITFIELD, INSERT_BITFIELD
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Reserve memory regions for CPU clusters according to P8700
cluster memory layout.
There's a set of components in the CPU cluster according to [1]
[1] https://mips.com/wp-content/uploads/2025/11/P8700-F_Programmers_Reference_Manual-TM.pdf
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
P8700 has a read-only cache configuration registers.
Provide a CPU specific function to extract cache information.
Use this information in the eyeq7h board for informational
message
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
On the EyeQ7H board, there's cluster level resets found in the
accelerator OLBs. These resets should be deasserted once on boot
and never used after
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
In the design, accelerator clusters ACC[01] and XNN[01] presence
indicated by the OLB_WEST register OLB_WEST_TSTCSR.
In the simulation environments, part (or all) accelerators may be
not instantiated
Disable clusters not present in the model, updating the DTB
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
In the eyeq7h platform, there's extra power control for the CPU
clusters. To enable cluster, it should be powered up using this OLB
registers prior to accessing any cluster management registers
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Refactor MIPS P8700 support, convert P8700 into a "CPU" and add
2 platforms using this CPU:
- "boston" - FPGA platform developed by MIPS
- "eyeq7h" - automotive platform by Mobileye
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Modify the coherence manager register accessors to use the global variable
p8700_cm_info instead of the statically declared GLOBAL_CM_BASE array.
Also use p8700_cm_info to get the number of coherence managers and their
base addresses in mips_p8700_early_init() and mips_p8700_nascent_init().
Clean up the hard-coded values in mips/board.h, access to the coherence
manager is now fully based on information provided by platform compatible
from the device tree.
Signed-off-by: Benoît Monin <[email protected]>
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Introduce a structure p8700_cm_info holding the number of coherence
managers and their base addresses found in a particular SoC.
Declare a global pointer to the structure that is set in
mips_p8700_platform_init(), based on the match data of the platform
compatible.
For the match data of the MIPS P8700, a single coherence manager with
a base address of 0x16100000 is declared, identical to what is found
in mips/board.h.
For now, access to the coherence manager register is still based on
the hard-coded values defined in mips/board.h.
Signed-off-by: Benoît Monin <[email protected]>
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
In the multi-cluster system each cluster has its own CM (Coherency Manager).
Every CM has its "global" memory address where it is accessible from
any bus master.
Initially, all CMs accessible from the local cluster using same "local"
address. Transactions by local address are not routed through system bus
and thus are faster.
Remap CM in every cluster to the local address matching its global address.
Then, every CM is always accessed using same address, but when transaction
initiated from the local cluster it is routed internally.
This removes need for 2 PMP regions covering local address access.
CM accessor functions simplified because there's no need to detect whether
transaction is local or global
Access timer always in cluster 0
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
When powering up cores, wait for power up to complete
using tight loop. This saves 10ms delay observed for every core
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
While powering up cluster, only indication is bit in cluster
power control.
It used to wait for CORE0 in that cluster reach U5 state
(non-coherent execution), this won't happen when only CM
powered up without booting any core
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Reserve memory upfront in large well aligned chunks,
to avoid problem with PMP granularity that is
64Kbytes for the p8700 CPU
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
use function call like format; debug print returning value
of the "read" accessor
Signed-off-by: Vladimir Kondratiev <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Altera provides a JTAG UART core that provides virtual UART over JTAG
and can coexist with their virtual JTAG. [1] This core has already been
supported by Linux and the programming interface has always been stable.
Add support for it to OpenSBI to ease JTAG prototype bringing up.
The driver follows the device tree binding in mainline Linux. [2]
[1] https://docs.altera.com/r/docs/683130/25.3/embedded-peripherals-ip-user-guide/jtag-uart-core
[2] https://github.com/torvalds/linux/blob/v6.19-rc1/Documentation/devicetree/bindings/serial/altr%2Cjuart-1.0.yaml
Signed-off-by: Icenowy Zheng <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Implement a system-wide suspend driver for the Andes AE350 platform.
This driver supports Andes-specific deep sleep (suspend to RAM) and
light sleep (suspend to standby) functionalities via the ATCSMU.
The major differences between deep sleep and light sleep are:
- Power Domain and Resume Path: Deep sleep powers down the core domain.
Consequently, harts waking from deep sleep resume from the reset
vector. Light sleep utilizes clock gating to the core domain; harts
maintain state and resume execution at the instruction immediately
following the WFI instruction.
- Primary Hart Wakeup: In both modes, the primary hart is woken by
UART or RTC alarm interrupts. In deep sleep, the primary hart is
additionally responsible for re-enabling the Last Level Cache (LLC)
and restoring Andes-specific CSRs.
- Secondary Hart Wakeup: In light sleep, secondary harts are woken
by an IPI sent from the primary hart. In deep sleep, they are
woken by an ATCSMU hardware wake-up command. Furthermore,
secondary harts must restore Andes-specific CSRs when returning
from deep sleep.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Introduce a FDT-based driver for the Andes Last Level Cache (LLC)
controller to support cache maintenance operations.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Implement a save and restore mechanism for Andes-specific CSRs to support
hardware power-saving modes, such as CPU hotplug or suspend to RAM.
Signed-off-by: Ben Zong-You Xie <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Refactor ATCSMU (System Management Unit) support by moving it from a
system utility into a dedicated FDT-based HSM driver.
Key changes include:
- Moving the functions in lib/utils/sys/atcsmu.c into the new HSM driver
- Moving hart start and stop operations on AE350 platform into the new
HSM driver
- Converting the assembly-based functions in sleep.S to C code for the
readability
- Updating the ATCWDT200 driver
Signed-off-by: Ben Zong-You Xie <[email protected]>
Signed-off-by: Leo Yu-Chi Liang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Hifive Premier P550[1] is a Mini-DTX form factor board with EIC7700X.
It has a STM32F407VET6 onboard MCU acting as the BMC, controlling
ATX power on/off while providing remote management features. The
EIC7700X SoC/SoM communicates with the BMC via UART2, using ESWIN's
protocol. The messages transmitted are fixed sizes (267 bytes), and
depending on the type, can be directional or bi-directional. The
shutdown and cold reboot requests are directional messages from SoC
to BMC (NOTIFY type) with CMD_POWER_OFF or CMD_RESTART. The payload
of shutdown/cold reboot requests should be empty and are ignored by
the BMC at the moment. A HFP (Hifive Premier) specific reset device
is registered in addition to the SoC reset device. For shutdown and
cold reboot, the board-level reset takes precedence.
The definitions of the SoC <-> BMC message protocol is taken from
ESWIN's repo [2]. The only file used from that repo is `hf_common.h`
It's disjunctively dual licensed as (GPL-2.0-only OR BSD-2-Clause),
hence, compatible with the license of OpenSBI. It's heavily modified
and renamed as platform/generic/include/eswin/hfp.h. The author and
copyright in the original file are retained.
Validated shutdown/cold reboot working on Hifive Premier P550.
[1] https://www.sifive.com/boards/hifive-premier-p550#documentation
[2] https://github.com/eswincomputing/hifive-premier-p550-mcu-patches.git
Signed-off-by: Bo Gan <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Initial platform support for ESWIN Computing EIC7700 based on public SoC
datasheet[1] and tested on HiFive Premier P550. Vendor U-boot/Linux boots
fine, and I've tested Geekbench 6.5.0 Preview and got scores on par with
the vendor OpenSBI. System shutdown/reboot for HiFive Premier P550 and
other boards will be implemented in subsequent commits. At this point,
only SoC-level warm reset is implemented.
The files and functions are intentionally named as eic770x in many places
for future enhancements to support the 2 die version of the same SoC,
namely EIC7702, seen on DC-ROMA AI PC FML13V03 [2]. This patch set only
deals with the single die version, and the assumption is we can be either
die with id=0 or id=1, but there's only a single die in the system, or we
are only using a single die out of 2. However, the way the SoC handles 2-
die greatly affects how we configure it in a 1-die setup. EIC770X address
map has die 0/1 memory regions interleaved (see comments in eic770x.c).
If only 1 die is connected or active, it creates holes in the address map
for those regions corresponding to the remote die. When speculative-
execution or HW prefetcher touches data-cacheable regions that happen to
fall into those holes, it can trigger bus error. Specifically:
- Remote (non-existent) die L3 zero device
- Remote (non-existent) die cached memory region
- Other holes in Memory Port
To make matters worse, EIC770X doesn't have cache coherent DMA, and due
to the fact that the P550 core lacks Svpbmt, the SoC maps main memory
twice as different regions, so it can bypass cache and fetch the data
directly from memory. In address space, we have two memory regions, one
as cached, the other as uncached. Thus, we also need an extra PMP entry
to protect OpenSBI blob from the uncached window. To do this, platform
code requires single_fw_region, otherwise, we'll run out of PMP entries.
EIC770X also have several feature disable/enable CSRs accessible in M
mode. By default many core features such as speculation and HW prefetch
are disabled, and M mode software is responsible of enabling. Hence,
introduce 4 new build time tunable parameters to Kconfig, which reflects
the values get updated to those CSRs:
- ESWIN_EIC770X_FEAT0_CFG
- ESWIN_EIC770X_FEAT1_CFG
- ESWIN_EIC770X_L1_HWPF_CFG
- ESWIN_EIC770X_L2_HWPF_CFG
The default values are somewhat optimal for generic workloads. They are
dumped when running SiFive's vendor OpenSBI, and in addition, with my
own tuning to address the perf regression reported by drmpeg [3]
To build the firmware+u-boot blob, Use the following, and docs [4] for
testing it with UART boot without flashing:
make FW_TEXT_START=0x80000000 \
FW_PAYLOAD_OFFSET=0x200000 \
FW_PAYLOAD_PATH=u-boot-nodtb.bin \
FW_PAYLOAD_FDT_ADDR=0xf8000000 \
FW_FDT_PATH=u-boot.dtb
[1] https://github.com/eswincomputing/EIC7700X-SoC-Technical-Reference-Manual
[2] https://github.com/geerlingguy/sbc-reviews/issues/82
[3] https://forums.sifive.com/t/low-1-core-stream-bandwidth/7274/15
[4] https://github.com/ganboing/EIC770x-Docs/blob/main/p550/bootchain/UART-Boot.md
Signed-off-by: Bo Gan <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Leaving no empty space in the FDT passed to the next booting stage
causes the following U-Boot crash on Ventana internal platforms:
Unhandled exception: Load access fault
EPC: 00000000fffa6372 RA: 00000000fffa7418 TVAL: 0001746174730068
EPC: 0000000080245372 RA: 0000000080246418 reloc adjusted
SP: 00000000fef38440 GP: 00000000fef40e60 TP: 0000000000000000
T0: 00000000fef40a70 T1: 000000000000ff00 T2: 0000000000000000
S0: 00000000fffc17a8 S1: 00000000fef38d40 A0: 7375746174730068
A1: 00000000fffc17a8 A2: 0000000000000010 A3: 0000000000000010
A4: 0000000000000000 A5: 00000000fffc17b8 A6: 0000000000ff0000
A7: 000000000000b100 S2: 0000000000000000 S3: 0000000000000001
S4: 00000000fef38d40 S5: 7375746174730068 S6: 0000000000000000
S7: 00000000fef4eef0 S8: 00000000fef4ef90 S9: 0000000000000000
S10: 0000000000000000 S11: 00000000fef4efc0 T3: 00000000fef40ea8
T4: 0000000000ff0000 T5: 00000000fef40a60 T6: 00000000fef40a6c
To address the above issue, keep some minimal empty space in the
FDT instead of no empty space.
Fixes: bbe9a23060e9 ("platform: generic: Pack the FDT after applying fixups")
Signed-off-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add the missing objects.mk for the SpacemiT platform, required for the
K1 platform to be included in the build.
Fixes: 1f84ec2a ("platform: generic: spacemit: add K1")
Signed-off-by: Junhui Liu <[email protected]>
Acked-by: Troy Mitchell <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add support for SiFive Extensible Cache (EC) controller with multi-slice
architecture. The driver implements cache maintenance operations through
MMIO register interface.
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Co-developed-by: Yong-Xuan Wang <[email protected]>
Signed-off-by: Yong-Xuan Wang <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
SiFive Private L2(PL2) cache is a private cache owned by each hart. Add
this driver to support private cache flush operations via the MMIO
registers.
Co-developed-by: Eric Lin <[email protected]>
Signed-off-by: Eric Lin <[email protected]>
Co-developed-by: Zong Li <[email protected]>
Signed-off-by: Zong Li <[email protected]>
Co-developed-by: Vincent Chen <[email protected]>
Signed-off-by: Vincent Chen <[email protected]>
Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Signed-off-by: Nick Hu <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
|
Add code for using generic_early_init so that the uart parameters
are parsed from dtb.
Signed-off-by: Manuel Hernández Méndez <[email protected]>
Reviewed-by: Anup Patel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Anup Patel <[email protected]>
|
