diff options
| -rw-r--r-- | bsp/renesas/ra2a1-ek/board/Kconfig | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/bsp/renesas/ra2a1-ek/board/Kconfig b/bsp/renesas/ra2a1-ek/board/Kconfig index c5c31871eb..7ef62b3e5e 100644 --- a/bsp/renesas/ra2a1-ek/board/Kconfig +++ b/bsp/renesas/ra2a1-ek/board/Kconfig @@ -96,7 +96,184 @@ menu "Hardware Drivers Config" default 0 endif endif + + menuconfig BSP_USING_SCI + bool "Enable SCI Controller" + default n + config BSP_USING_SCIn_SPI + bool + depends on BSP_USING_SCI + select RT_USING_SPI + default n + config BSP_USING_SCIn_I2C + bool + depends on BSP_USING_SCI + select RT_USING_I2C + default n + + config BSP_USING_SCIn_UART + bool + depends on BSP_USING_SCI + select RT_USING_SERIAL + select RT_USING_SERIAL_V2 + default n + + if BSP_USING_SCI + config BSP_USING_SCI0 + bool "Enable SCI0" + default n + if BSP_USING_SCI0 + choice + prompt "choice sci mode" + default BSP_USING_SCI0_SPI + config BSP_USING_SCI0_SPI + select BSP_USING_SCIn_SPI + bool "SPI mode" + config BSP_USING_SCI0_I2C + select BSP_USING_SCIn_I2C + bool "I2C mode" + config BSP_USING_SCI0_UART + select BSP_USING_SCIn_UART + bool "UART mode" + endchoice + if BSP_USING_SCI0_UART + config BSP_SCI0_UART_RX_BUFSIZE + int "Set UART0 RX buffer size" + range 64 65535 + depends on RT_USING_SERIAL_V2 + default 256 + + config BSP_SCI0_UART_TX_BUFSIZE + int "Set UART0 TX buffer size" + range 0 65535 + depends on RT_USING_SERIAL_V2 + default 0 + endif + endif + config BSP_USING_SCI1 + bool "Enable SCI1" + default n + if BSP_USING_SCI1 + choice + prompt "choice sci mode" + default BSP_USING_SCI1_SPI + config BSP_USING_SCI1_SPI + select BSP_USING_SCIn_SPI + bool "SPI mode" + config BSP_USING_SCI1_I2C + select BSP_USING_SCIn_I2C + bool "I2C mode" + config BSP_USING_SCI1_UART + select BSP_USING_SCIn_UART + bool "UART mode" + endchoice + if BSP_USING_SCI1_UART + config BSP_SCI1_UART_RX_BUFSIZE + int "Set UART1 RX buffer size" + range 64 65535 + depends on RT_USING_SERIAL_V2 + default 256 + + config BSP_SCI1_UART_TX_BUFSIZE + int "Set UART1 TX buffer size" + range 0 65535 + depends on RT_USING_SERIAL_V2 + default 0 + endif + endif + + config BSP_USING_SCI9 + bool "Enable SCI9" + default n + if BSP_USING_SCI9 + choice + prompt "choice sci mode" + default BSP_USING_SCI9_SPI + config BSP_USING_SCI9_SPI + select BSP_USING_SCIn_SPI + bool "SPI mode" + config BSP_USING_SCI9_I2C + select BSP_USING_SCIn_I2C + bool "I2C mode" + config BSP_USING_SCI9_UART + select BSP_USING_SCIn_UART + bool "UART mode" + endchoice + if BSP_USING_SCI9_UART + config BSP_SCI9_UART_RX_BUFSIZE + int "Set UART9 RX buffer size" + range 64 65535 + depends on RT_USING_SERIAL_V2 + default 256 + + config BSP_SCI9_UART_TX_BUFSIZE + int "Set UART9 TX buffer size" + range 0 65535 + depends on RT_USING_SERIAL_V2 + default 0 + endif + endif + endif + + menuconfig BSP_USING_HW_I2C + bool "Enable hardware I2C BUS" + default n + if BSP_USING_HW_I2C + config BSP_USING_HW_I2C0 + bool "Enable Hardware I2C0 BUS" + default n + config BSP_USING_HW_I2C1 + bool "Enable Hardware I2C1 BUS" + default n + endif + + menuconfig BSP_USING_PWM + bool "Enable PWM" + default n + select RT_USING_PWM + if BSP_USING_PWM + config BSP_USING_PWM0 + bool "Enable GPT0 (32-Bits) output PWM" + default n + + config BSP_USING_PWM1 + bool "Enable GPT1 (32-Bits) output PWM" + default n + + config BSP_USING_PWM2 + bool "Enable GPT2 (32-Bits) output PWM" + default n + + config BSP_USING_PWM3 + bool "Enable GPT3 (32-Bits) output PWM" + default n + + config BSP_USING_PWM4 + bool "Enable GPT4 (32-Bits) output PWM" + default n + + config BSP_USING_PWM5 + bool "Enable GPT5 (32-Bits) output PWM" + default n + + config BSP_USING_PWM6 + bool "Enable GPT6 (32-Bits) output PWM" + default n + endif + + menuconfig BSP_USING_SPI + bool "Enable SPI BUS" + default n + select RT_USING_SPI + if BSP_USING_SPI + config BSP_USING_SPI0 + bool "Enable SPI0 BUS" + default n + config BSP_USING_SPI1 + bool "Enable SPI1 BUS" + default n + endif endmenu menu "Board extended module Drivers" |